Polaris Water Heater PG10 100 199 3NV OR 3PV User Manual

This manual covers model numbers:

United States

Canada

PG10* 34-100-2NV or 2PV PR 100-34 2NV or 2PV

PG10* 34-130-2NV or 2PV PR 130-34 2NV or 2PV

PG10* 50-130-2NV or 2PV PR 130-50 2NV or 2PV

PG10* 34-150-2NV or 2PV PR 150-34 2NV or 2PV

PG10* 50-175-3NV or 3PV PR 175-50 3NV or 3PV

PG10* 50-199-3NV or 3PV PR 199-50 3NV or 3PV

PG10* 100-199-3NV or 3PV PR 199-100-3NV or 3PV

* Indicates warranty period

Note:

The manufacturer of this water heater recommends that it

be professionally installed by trained and qualified service

professionals.

Polaris

Residential Gas

Water Heater

Installation

WARNING: If the information in these

instructions is not followed exactly, a fire

or explosion may result causing property

damage, personal injury or death.

Instructions and

Use & Care Guide

To obtain technical, warranty or service assistance during or

after the installation of this water heater, visit our website at:

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

http://www.americanwaterheater.com

or call toll free:

1-800-456-9805.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

When calling for assistance, please have the following

information ready:

• Do not touch any electrical switch;

do not use any telephone in your

building.

1. Model number

2. 7 Digit product number

3. Serial number

• Immediately call your gas supplier

from a neighbor’s telephone. Follow

the gas supplier’s instructions.

4. Date of installation

5. Place of Purchase

• If you cannot reach your gas

supplier, call the fire department.

Table of Contents .......................................................... 2

Installation and service must be performed

by a qualified installer, service agency or

the gas supplier.

INSTALLER:

•

Afﬁx these instructions to or adjacent to the water

heater.

OWNER:

•

Retain these instructions and warranty for future

reference. Retain the original receipt as proof of

purchase.

6510336

December 2004

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION INSTRUCTIONS

Consumer Information

Unpacking the Water Heater

OBSERVE ALL GOVERNING CODES AND ORDINANCES.

This water heater is design-certified by CSA International

as a Category IV, direct vented water heater which takes

its combustion air from the outside of the structure and

exhausts all products of combustion to the outside of the

structure.

Excessive Weight Hazard

Use two or more people to move and

install water heater unless proper

handling equipment is utilized.

Failure to do so can result in back or

other injury.

This water heater must be installed according to all local

and state codes or in the absence of local and state codes

with the “National Fuel Gas Code”, ANSI Z223.1(NFPA

54)- latest edition. Canadian installations must be per-

formed in accordance with CAN/CGA-B149. This is avail-

able from the following:

Removing Packaging Materials

Important: Do not remove any permanent instructions,

labels, or the data plate from outside of the water heater or

on the inside of panels.

CSA America, Inc.

8501 East Pleasant Valley Road

Cleveland, OH 44131

National Fire Protection Agency

1 Batterymarch Park

Quincy, MA 02169-7471

•

Remove exterior packaging and place installation

components aside.

Inspect all parts for damage prior to installation and

start-up.

Completely read all instructions before attempting to

assemble and install this product.

After installation, dispose of packaging material in the

proper manner.

Canadian Standards Association

178 Rexdale Boulevard

Toronto, ON M9W 1R3

Check the phone listings for the local authorities having

jurisdiction over this installation.

Installer and Owner Responsibilities

This manual has been prepared to acquaint you with the

installation, operation, and maintenance of your gas water

heater and provide important safety information in these

areas.

Read all of the instructions thoroughly before attempting

the installation or operation of this water heater.

Do not discard this manual. You or future users of this

water heater will need it for future reference.

Service to the water heater should only be performed

by a qualified service technician.

Examples of qualified service technicians include:

those trained in the plumbing and heating industry,

local gas utility personnel, or an authorized service

person.

The manufacturer and seller of this water heater will

not be liable for any damages, injuries, or deaths

caused by failure to comply with the installation and

operating instructions outlined in this manual.

If you lack the necessary skills required to properly install

this water heater, or you have difficulty following the

instructions, you should not proceed but have a qualified

service technician perform the installation of this water

heater.

Massachusetts code requires this water heater to be

installed in accordance with Massachusetts Plumbing and

Fuel Gas Code 248 CMR section 2.00 and 5.00.

A data plate identifying your water heater can be found on

the front of the heater. When referring to your water heater,

always have the information listed on the data plate readily

available.

Retain your original receipt as proof of purchase.

Download from Www.Somanuals.com. All Manuals Search And Download.

•

Consider the inlet and exhaust vent system piping

when selecting the water heater location. The venting

system must be able to run from the water heater to

the termination with a minimal length and number of

elbows. Input rates are reduced as vent system length

increases. The venting system must comply with the

requirements set forth in the venting section of this

manual.

Locate the water heater near the existing gas piping.

If installing a new gas line, locate the water heater to

minimize the pipe length and elbows.

Important: Air for combustion and ventilation must not

come from a corrosive atmosphere. Any failure due to cor-

rosive elements in the atmosphere is excluded from war-

ranty coverage.

Note: The water heater must be installed according to all

local and state codes or in absence of the local and state

codes with the “National Fuel Gas Code”, ANSI Z223.1

(NFPA 54)-latest edition. Canadian installations must be

performed in accordance with CAN/CGA-B149.

FIRE AND EXPLOSION HAZARD

Can result in serious injury or death

Do not store or use gasoline or other

flammable vapors and liquids in the vicinity

of this or any other appliance. Storage of or

use of gasoline or other flammable vapors

or liquids in the vicinity of this or any other

appliance can result in serious injury or death

Important: The water heater should be located in

an area where leakage of the tank or connections will

not result in damage to the area adjacent to the water

heater or to lower floors of the structure. Due to the

normal corrosive action of the water, the tank will

eventually leak after an extended period of time.

Also any external plumbing leak, including those

from improper installation, may cause early failure

of the water tank due to corrosion if not repaired.

A qualified service technician should be contacted

for repairs. A suitable metal drain pan should be

installed under the water heater as shown below, to help

protect the property from damage which may occur from

condensate formation or leaks in the piping connections

or tank. The pan must limit the water level to a maximum

depth of 1-3/4” and be at least two inches wider than

the heater and piped to an adequate drain. Locate the

water heater near a suitable indoor drain. Outside drains

are subject to freezing temperatures which can obstruct

the drain line. The piping should be at least 3/4” ID and

pitched for proper drainage. Under no circumstances will

the manufacturer or seller of this water heater be held

liable for any water damage which is caused by your

failure to follow these instructions.

Location Requirements

The water heater design has been tested by CSA

International and complies with ANSI Z21.10.1, Section

2.35 Flammable Vapors Resistance. In garage installation

avoid damage to your water heater by installing a vehicle

stop as shown in figure below. Check state and local

codes for requirements prior to installation.

Figure 1: Garage Installation

This water heater is not certified for installation in mobile

homes.

Note: In the State of California, the water heater must be

braced, anchored, or strapped to avoid moving during an

earthquake. Contact local utilities for code requirements in

your area or call 1-800-456-9805 and request instructions.

34/50 GAL. MODEL SHOWN

Site Location

•

The water heater should be located in an area not sub-

ject to freezing temperatures. Water heaters located in

unconditioned spaces (i.e., attics, basements, etc) may

require insulation of the water piping and drain piping

to protect against freezing. The drain and controls must

be easily accessible for operation and service. Maintain

proper clearances as specified on the data plate.

•

Select a location near the center of the water piping

system. The water heater must be installed indoors

and in a vertical position on a level surface. DO NOT

install in bathrooms, bedrooms, or any occupied room

normally kept closed. Note: The water heater may be

installed in a closet with a door off a bedroom or bath-

room providing the units are installed and vented per

the manufacturer’s instructions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Clearances and Accessibility

Notice: Minimum clearances from combustible materi-

als are stated on the data plate located on the front of the

water heater.

Figure 3A: 2” Condensation Trap Installation

100,000 - 150,000 BTU/Hr Models

•

The water heater is certified for installation on a

combustible floor.

Important: If installing over carpeting, the carpeting must

be protected by a metal or wood panel beneath the water

heater. The protective panel must extend beyond the full

width and depth of the water heater by at least 3 inches

(76.2mm) in any direction or if in a alcove or closet instal-

lation, the entire floor must be covered by the panel. The

panel must be strong enough to carry the weight of the

heater when full of water.

Figure 2 may be used as a reference guide to locate the

specific clearance locations. A minimum of 24 inches of

front clearance and 4 inches on each side should be pro-

vided for inspection and service.

Figure 3B: 3” Condensation Trap Installation

175,000 - 199,000(50 gal.) BTU/Hr Models

Figure 2: Minimum Clearance Locations

Figure 3C: 3” Condensation Trap Installation

100 Gallon Models

CONDENSATE LINE

Important: Do not run the condensate drain in areas

that are likely to freeze. Frozen condensate will block the

drain line and result in property damage or water heater

malfunction.

Condensate Trap Assembly

A condensate trap/drain stem assembly has been supplied

with the water heater and is located behind the access door

inside the base of the water heater. This assembly must be

installed between the water heater and the exhaust outlet

piping to ensure proper operation of the water heater. To

install, remove the slip-joint nut, stainless steel washer, and

O-ring from the trap assembly. Slip the nut, washer and

O-ring (in that order) over the stainless exhaust tubing and

slide them back near the base of the heater. Insert the trap

assembly over the tubing (see figure 3A or 3B accordingly)

and firmly hand-tighten (using a wrench will cause the

O-ring to seal improperly) the nut to form a water-tight

seal between the O-ring and the stainless exhaust tubing.

When tightened, the nut to heater base clearance should

be 3/4” (+/- 1/8”). On 100 gallon models the condensate

trap assembly should be glued to the exhaust pipe (see

figure 3C).

Note: The trap should be aligned so that the exhaust pipe

is in a vertical position close to the surface of the water

heater.

Download from Www.Somanuals.com. All Manuals Search And Download.

VENT PIPE SYSTEM

Figure 4: Condensate Drain

Carbon Monoxide Hazard

Follow all instructions to locate and install

the vent pipe system.

Instructions can be found in this manual, in

state or local codes (or the authority having

jurisdiction), or in the absence of such, the

National Fuel Gas Code, ANSI Z223.1, NFPA

54, Latest Edition. Canadian installations

must be performed in accordance with

CAN/CGA-B149.

Condensate Drain Line

All parts of the condensate trap are glued except for the

1/2” CPVC drain stem joint at the elbow (see figure 3). This

assembly can be turned with the outlet of the tee oriented

as needed.

Failure to properly locate and install the

vent pipe system can result in death or

carbon monoxide poisoning.

Once orientation direction is decided, remove the unglued

joint from the elbow at the bottom and apply a suitable

cement to joint. Re-insert the joint fully and quickly into

the elbow making sure to orient it before the cement sets.

Connect the remaining piping and run the condensate drain

line to a suitable drain.

Venting

This water heater has a direct vent system in which all air

for combustion is taken from the outside atmosphere and

all combustion products are discharged to the outdoors.

Important: Be sure the drain stem joint is inserted against

the stop in the elbow. Failure to do so may result in

improper water heater operation.

This water heater must be properly vented for removal

of exhaust gases to the outside atmosphere. Correct

installation of the vent pipe system is mandatory for the

safe and efficient operation of this water heater and is an

important factor in the life of the unit.

If required by local codes, install a condensate neutralizer

cartridge on the drain line (see figure 4).

The condensate drain line must be routed to a suitable

drain. If no ﬂoor drain is available or the drain is above

the level of the condensate line, install a condensate pump

that is resistant to the acidic condensate. These pumps are

available from local distributors. If the pump is not resistant

to acidic water, a condensate neutralizer must be used

ahead of the pump.

Vent pipe installation must be performed in accordance

with state and local codes, or in the absence of such, the

National Fuel Gas Code, NFPA 54, ANSI Z223.1-latest

edition. Canadian installations must be performed in

accordance with CAN/CGA-B149.

When replacing an existing Polaris unit, it is recommended

that the venting system be reviewed for compliance with

the requirements contained in this installation manual. If the

venting is not in compliance, it is recommended that the

appropriate changes be made to bring it into compliance.

If this is not practical, and the existing venting system

complies with a prior Polaris installation manual the venting

requirements as stated in the updated installation manual

do not have to be met: however, vent length in excess of

those referenced in the manual will result in reduced input.

Note: in either case it is important that the inlet air filter

supplied with this unit be installed in the inlet combustion

air piping. (Follow installation instructions supplied with the

filter kit). Note: if the vent system is not in compliance with

the current or prior installation manuals, the manufacturer

reserves the right to evaluate the installation prior to

granting any warranty on service claims.

When installing the drain line, note the following:

•

Plastic pipe or tubing must be used to connect the

condensate drain to a suitable drain or condensate

pump. Do not use copper tubing, iron, or steel pipe for

the condensate drain line.

•

Condensate drain lines should be installed in condi-

tioned areas only. Drain lines installed in areas that are

subject to freezing temperatures should be wrapped

with a nationally recognized/listed heat tape and/or

approved insulation for freeze protection. Install per

manufacturer’s instructions.

•

Do not common drain with the temperature and pres-

sure relief valve or the condensate line from an air

conditioner evaporator coil.

•

Slope the condensate drain toward the inside ﬂoor

drain or condensate pump.

The condensate drain line and connection to the drain

piping must comply with all local codes.

Important: Check to make sure the vent pipe is not

blocked in any way.

Note: Do not common vent this water heater with any

other appliance. Do not install in the same chase or

chimney with a metal or high-temperature plastic from

another gas or fuel burning appliance.

Do not run the condensate line into the drain pan.

Download from Www.Somanuals.com. All Manuals Search And Download.

All pipe, fittings, pipe cement, primers and procedures

must conform to American National Standard Institute and

American Society for Testing and Materials (ANSI/ASTM)

standards in the United States. This water heater has been

design certified by the Canadian Standards Association for

use with the specified (CSA) listed plastic vent pipe.

Vent Pipe Material

The following plastic materials may be used for both the

combustion air inlet and exhaust outlet piping subject to

state and local codes:

• Schedule 40 PVC or ABS

• Schedule 40 or 80 CPVC

• DWV Pipe is acceptable

All joints in the inlet and outlet piping must be properly

cemented. Size and cut all piping before cementing.

1. Cut the pipe end square and remove all ragged edges

and burrs. Make sure the inside of the pipe is clean

and free of cuttings and loose dirt. Chamfer the end

and apply primer to the fitting and pipe.

2. Using a suitable grade of pipe cement, apply a moder-

ate, even coat inside the fitting. Apply a liberal amount

of cement to the outside of the pipe to socket depth.

Note: It is important to select the proper pipe cement for

the type of plastic pipe being used.

Note: Use only solid (not foam core) piping.

Plastic pipe and fittings are available through most plumb-

ing suppliers. Always check the marking on the pipe to

make sure you are using the correct material.

Important: Do not use vent elbows in this vent pipe installa-

tion (see figure 5 below).

Figure 5: Correct and Incorrect Pipe Fittings

3. Assemble the parts quickly while the cement is

still wet. Twist the pipe 1/4 turn during insertion

and hold for 30 seconds.

Vent Pipe Length

Size the exhaust outlet and combustion air inlet pipes as

specified in Table 1. This table lists the maximum allow-

able length in feet of the exhaust outlet and combustion air

inlet pipes as related to the number of required elbows and

the termination. The specified maximum lengths are for

the separate inlet and exhaust pipe systems and not the

combined length of both systems. Minimum pipe length is

6 feet with one elbow per side.

Vent Pipe Installation

1. Determine termination type and pipe size.

2. Determine number of elbows in exhaust pipe. Do not

include the elbows in the termination or the condensate

trap. Corresponding number Indicates the maximum

length of exhaust pipe.

3. Determine number of elbows in inlet pipe. Do not

include the elbows in the termination. The correspond-

ing number indicates the maximum length of inlet pipe.

The following guidelines should be followed when installing

the air inlet and exhaust outlet piping:

•

Venting should be as direct as possible with a minimum

number of pipe fittings.

Vent diameter must not be reduced unless specifically

noted in the installation instructions.

All 2” horizontal vent piping must be sloped upward

1/4 inch per foot (3” Piping must slope upward at 1/8”

per foot) so that condensate will run back to the heater

and exit through the condensate trap.

•

Support all horizontal pipe runs every four feet and

all vertical pipe runs every six feet or according to

local codes.

Vents run through unconditioned spaces where below

freezing temperatures are expected should be properly

insulated to prevent freezing. For horizontal runs, wrap

the vent pipe with nationally recognized/listed heat tape

and/or approved insulation for freeze protection. Install

per the manufacturer’s instructions.

•

An air intake filter is included with the unit and must be

installed according to the installation instructions

supplied with the filter.

The combustion air inlet and exhaust outlet piping and

termination may be installed in one of the following type

terminations:

1. Standard Horizontal (2 Pipe)

2. Alternate Horizontal (2 Pipe)

3. Vertical (2 Pipe)

4. Concentric Vent - Through the Wall

5. Concentric Vent - Through the Roof

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Use only 2 inch pipe or a 2 inch concentric vent on

the vent termination for 100,000 - 150,000 BTU/Hr

models. For inputs of 175,000 BTU/Hr or more, use

only 3 inch pipe or a 3 inch concentric vent. Do not

expose any 3” X 2” reducers or bushings to out-

door ambient temperatures.

2. The air inlet and exhaust outlet must not terminate

under a patio, deck or any covered area.

3. Do not terminate the vent near walkways or into alleys

or other publicly accessible areas.

4. Do not terminate the vent in an area where children

or animals could block pipes.

5. Do not locate the vent terminal too close to shrubs or

bushes.

6. Caulk all cracks, seams and joints within 6 feet horizon-

tally above and below the vent.

7. Combustion air inlet termination and exhaust air termi-

nation must be located in the same pressure zone.

Vent Termination Locations

The air inlet and exhaust outlet must be installed with the

following minimum clearances (see figure 6):

•

Twelve inches above grade or maximum anticipated

snow level.

Twelve inches from any opening through which flue

gases could enter the structure.

Four feet horizontally and vertically from gas or electric

meters, gas regulators, dryer vents, vent hoods, bath-

room fan exhaust, attic fans and turbines.

Two feet from an inside corner formed by two exterior

walls.

Two feet from porches, decks, overhangs and other

obstructions.

•

In addition to maintaining the minimum clearances , the

vent should terminate according to the following guidelines:

Figure 6: Minimum Clearances for Inlet/Outlet and Concentric Vent

US Installations

Canadian Installations

A. 12 in (30 cm) min. clearance above grade,

veranda, porch, deck, balcony, or maximum

anticipated snow level.

A. 12 in (30 cm) min. clearance above grade,

veranda, porch, deck, balcony, or maximum

anticipated snow level.

B. 12 in (30 cm) min. clearance on top and side of

window or door that may be opened. Do not install

below a window or door that may be opened.

B. 12 in (30 cm) min. clearance on top and side of

window or door that may be opened. Do not install

below a window or door that may be opened.

C. Clearance to permanently closed window.**

D. 12 in (30 cm) min vertical clearance to ventilated

soffit located above the terminal within a horizontal

distance of 2 ft (61 cm) from the center line of the

terminal.

D. 12 in (30 cm) min vertical clearance to ventilated

soffit located above the terminal within a horizontal

distance of 2 ft (61 cm) from the center line of the

terminal.

E. 12 in (30 cm) min. clearance to unventilated soffit.

F. Clearance to outside corner **

F. Clearance to outside corner. **

G. 2 ft (61 cm) clearance to inside corner formed by

two exterior walls.

H. 4 ft (122 cm) clearance to each side of center line

H. 3 ft (91 cm) within a height 15 ft (4.57 m) above the

extending above meter/regulator assembly.

meter/regulator assembly.

I. 4 ft (122 cm) clearance to service regulator vent

I. 4 ft (122 cm) clearance to service regulator vent outlet.

outlet.

J. 12 in (30 cm) clearance to nonmechanical air

supply inlet to building or the combustion air inlet to

any other appliance.

J. 12 in (30 cm) clearance to nonmechanical air

supply inlet to building or the combustion air inlet

to any other appliance.

K. 6 ft (1.83 m) clearance to mechanical air supply inlet.

K. 3 ft (91 cm) above if within 10 ft (3 m) horizontally of

mechanical air supply inlet.

**Clearance in accordance with local installation codes and the requirements of the gas supplier.

Download from Www.Somanuals.com. All Manuals Search And Download.

INLET/OUTLET VENT TERMINATIONS (100,000 - 150,000 BTU/HR)

Standard Horizontal Termination

Alternative Horizontal Termination

When 3 inch pipe is used between the water heater and the The combustion air and exhaust terminations may be raised

outside wall, reduce it to 2 inch pipe before penetrating the up to 24 inches above the wall penetrations if required for

wall. A maximum of 18 inches of 2 inch pipe may be used anticipated snow levels (see figure 8A). The two elbows

between the 3 inch transition and the inside of the wall (see shown in figure 8A are considered part of the termination

figure 7A).

and should not be included when determining the maximum

allowable vent pipe length.

The standard horizontal air inlet termination is a 2 inch

pipe which terminates at the exterior wall and utilizes a Note: See “Venting Additional Polaris® Units” on Page 10

coupling to prevent the pipe from being pushed back into the for correct terminations if installing more than one Polaris®

structure. The standard horizontal exhaust outlet termination gas water heater.

is a 2 inch pipe which terminates 12 inches from the outside

wall. The air inlet must be located with respect to the exhaust

outlet as shown in figure 7A (bottom).

Figure 8A: Alternate Horizontal Termination

(100,000 - 150,000 BTU/Hr Input Models)

Install a drain tee assembly and trap in the inlet vent as

close to the water heater as possible. This is to drain any

water that may be in the combustion air pipe and prevent

it from entering the blower. Connect the trap drain line to a

suitable drain or downstream of the condensate trap of the

water heater.

Note: See “Venting Additional Polaris® Units” on Page 10

for correct terminations if installing more than one Polaris®

gas water heater.

Figure 7A: Standard Horizontal Termination (100,000 - 150,000 BTU/Hr Models)

Download from Www.Somanuals.com. All Manuals Search And Download.

VERTICAL TERMINATIONS (100,000 - 150,000 BTU/HR)

When 3 inch pipe is used between the water heater and the The air inlet and exhaust outlet terminations must be at

roof, reduce it to 2 inch pipe before penetrating the roof. A least 12 inches above the roof line or anticipated snow

maximum of 18 inches of 2 inch pipe may be used between levels. See figure 9A below.

the 3 inch transition and the inside of the roof.

Note: See “Venting Additional Polaris® Units” below if

installing more than one Polaris® gas water heater.

The vertical inlet air termination requires a return bend

or two short or long sweep radius 90 elbows to keep the

inlet downward and prevent entry of rain. These elbows

are considered part of the termination and should not be

included when calculating the maximum allowable vent

pipe length. Refer to figure 9A for the proper location of the

air inlet with respect to the exhaust outlet termination. The

vertical exhaust outlet termination is a 2 inch pipe which

terminates at least 12 inches above the inlet air termination.

Figure 9A: Vertical Termination (100,000 - 150,000 BTU/Hr Models)

When using three or more Polaris® units, install vent

terminations per Method C or Method D:

Venting Additional Polaris® Units

(100,000 - 150,000 BTU/hr Models)

When using two (2) Polaris® units, install vent terminations

using either Method A or Method B below:

Download from Www.Somanuals.com. All Manuals Search And Download.

CONCENTRIC VENT TERMINATIONS (100,000 - 150,000 BTU/HR)

For new installations, install 2” Concentric vent kit model

Figure 13A: Through the Wall Termination

KGAVT0501CVT, part number 6910542. See Manufacturer’s

instructions for complete installation or call customer service at

1-800-456-9805 for assistance.

For planning purposes, see figures 10A-13A below for vent

terminal specifications.

Note: For replacement installations, previously installed

American Water Heater Company supplied concentric vent kits

are acceptable for use on 100,000-130,000 BTU/Hr models only.

Figure 10A: 2 Inch Concentric Vent

Figure 11A: Through the Wall Termination

Note: For concentric venting terminations (all models), see

“Concentric Venting Multiple Water Heaters” on Page 14.

Figure 12A: Through the Roof Termination

Download from Www.Somanuals.com. All Manuals Search And Download.

INLET/OUTLET VENT TERMINATIONS (175,000+ BTU/HR)

Alternative Horizontal Termination

Standard Horizontal Termination

The combustion air and exhaust terminations may be

raised up to 24 inches above the wall penetrations if

required for anticipated snow levels (see figure 8B). The

two elbows shown in figure 8B are considered part of the

termination and should not be included when determining

the maximum allowable vent pipe length.

The standard horizontal air inlet termination is a 3 inch

pipe which terminates at the exterior wall and utilizes a

coupling to prevent the pipe from being pushed back into

the structure. The standard horizontal exhaust outlet termi-

nation is a 3 inch pipe which terminates 12 inches from the

outside wall. The air inlet must be located with respect to

the exhaust outlet as shown in figure 7B (bottom).

Note: See “Venting Additional Polaris® Units” on Page 13

for correct terminations if installing more than one Polaris®

gas water heater.

Install a 3 inch coupling at the outside wall on both the inlet

and exhaust to prevent the terminations from being pushed

inward.

Figure 8B: Alternative Horizontal Termination

(175,000+ BTU/Hr or greater input models)

Install a drain tee assembly and trap in the inlet vent as

close to the water heater as possible. This is to drain any

water that may be in the combustion air pipe and prevent it

from entering the blower. Connect the trap drain line to a

suitable drain or downstream of the condensate trap of the

water heater.

Note: See “Venting Additional Polaris® Units” on Page 13

for correct terminations if installing more than one Polaris®

gas water heater.

Figure 7B: Standard Horizontal Termination (175,000+ BTU/Hr models)

*100 Gallon Model Shown.

Download from Www.Somanuals.com. All Manuals Search And Download.

VERTICAL TERMINATIONS (175,000+ BTU/HR)

For inputs of 175,000 BTU/Hr or greater, all termination pip- The air inlet and exhaust outlet terminations must be at

ing and fittings are 3”. Do not reduce before penetrating

the wall.

least 12 inches above the roof line or anticipated snow

levels as shown in figure 9B below.

Note: See “Venting Additional Polaris Units” below if

The vertical inlet air termination requires a return bend or

two short or long sweep radius 90° elbows to keep the inlet

downward and prevent entry of rain. These elbows are con-

sidered part of the termination and should not be included

when calculating the maximum allowable vent pipe length.

Refer to figure 9B for the proper location of the air inlet

with respect to the exhaust outlet termination. The vertical

exhaust outlet termination is a 3 inch pipe which terminates

at least 12 inches above the inlet air termination.

installing more than one Polaris gas water heater.

Figure 9B: Vertical Termination (175,000+ BTU/Hr models)

*100 Gallon Model Shown.

When using three or more Polaris® units, install vent

terminations per Method C or Method D:

Venting Additional Polaris® Units

(175,000+ BTU/Hr Models)

When using two (2) Polaris® units, install vent terminations

using either Method A or Method B below:

Download from Www.Somanuals.com. All Manuals Search And Download.

CONCENTRIC VENT TERMINATIONS (175,000 + BTU/HR)

For new installations, install 3” Concentric vent kit

Figure 13B: Concentric Vent Piping Installation

model KGAVT0601CVT, part number 6910543. See

Manufacturer’s instructions for complete installation or call

customer service at 1-800-456-9805 for assistance.

For planning purposes, see figures 10B-13B below for vent

terminal specifications.

Figure 10B: 3 Inch Concentric Vent

Figure 11B: Through the Wall Termination

*100 Gallon Model Shown.

Note: For concentric venting terminations (all models), see

“Concentric Venting Multiple Water Heaters” on Page 14.

Concentric Venting Multiple Water

Heaters (All Models)

When using two Polaris® units, install vent terminations

using either Method E or Method F below:

Figure 12B: Through the Roof Termination

Note: For installation of more than two Polaris units, fol-

low the pattern established in Method G.

Download from Www.Somanuals.com. All Manuals Search And Download.

Gas Input Rate

The gas input rate of this water heater is affected by

several environmental factors such as:

Figure 14: Input Graph

•

The heating value of the gas

The air and gas densities (which vary widely due to baro-

metric pressure and temperature changes)

Venting installations (pipe diameter, length and fittings)

Altitude

•

When measuring the input rate these factors should be

incorporated into the calculations. Also measure the gas

consumption over a sufficiently long time to obtain an

accurate gas consumption rate (e.g. 3-5 minutes, not one

revolution of the meter needle).

Long vents and each additional elbow, inherently reduce

the gas input rate due to increased resistance to moving

combustion air and flue gases. The approximate maximum/

minimum input for the 100k, 130k, 150k, 175k, and the

199k models is shown in figure 14.

WATER PIPING SYSTEM

Piping Installation

Piping, ﬁttings, and valves should be installed according to

the installation drawing (ﬁgure 15). If the indoor installation

area is subject to freezing temperatures, the water piping

must be protected by insulation.

easily accessible. Know the location of this valve and

how to shut off the water to the heater.

6. The Polaris gas water heater is shipped with a fac-

tory-installed Temperature and Pressure Relief Valve.

Install a discharge line in the opening in the T & P valve

(see instructions on Page 18).

7. After piping has been properly connected to the water

heater, remove the aerator at the nearest hot water

faucet. Open the hot water faucet and allow the tank

to completely ﬁll with water. (To prevent damage to

the unit, DO NOT connect power until the tank is

COMPLETELY FILLED). To purge the lines of any

excess air, keep the hot water faucet open for 3 min-

utes after a constant ﬂow of water is obtained. Close

the faucet and check all connections for leaks.

Water supply pressure should not exceed 80% of the

working pressure of the water heater. The working pressure

is stated on the water heater’s data plate. If this occurs a

pressure reducing valve with a bypass should be installed

in the cold water inlet line to the entire system. This should

be placed on the supply to the entire structure in order to

maintain equal hot and cold water pressures.

Important: Heat cannot be applied to the water ﬁttings

on the heater as they may contain nonmetallic parts.

If solder connections are used, solder the pipe to the

adapter before attaching the adapter to the hot and

cold water ﬁttings.

Corrosion and Water Quality

Water quality will vary from location to location and may

contain contaminates that may reduce the life or perfor-

mance of the water heater. To test for contaminates a

water quality test kit is available, reference part number

6903791.

Important: Do not install this water heater with iron or

galvanized piping. Use brass caps on all unused inlet/

outlet connections.

Contaminates which can reduce the life or performance

of the water heater if present in high quantities include

those which contribute to hardness (dissolved minerals

such as sodium, calcium and magnesium); plus chlorides

and sulfates. Additionally, water that is too acidic or basic

(measured as pH) can reduce the life of the water heater.

Water treatment systems (such as water softeners for

hardness) should be used and maintained properly if the

contaminate levels exceed the following:

1. Install the water piping and ﬁttings as shown in ﬁgure

15. Note: If state or local codes require, install a vacu-

um relief valve per the manufactures instructions in the

cold water supply line. Connect the cold water supply

(50 gal. and below use 1” NPT, 100 gal. use 1-1/2”

NPT) to the ﬁtting marked “COLD INLET”. Do not turn

the cold water nipple. The mark should remain along

the top side of the nipple (34 & 50 gal models only.)

Connect the hot water supply (50 gal. and below use

1” NPT, 100 gal. use 1-1/2” NPT) to the ﬁtting marked

“HOT OUTLET”.

Warranty is void in applications which exceed the

water quality requirements listed below.

2. Always use a suitable grade of joint compound and be

certain that all ﬁttings are tightened properly.

3. The installation of unions in both the hot and cold water

supply lines is recommended for ease of removing the

water heater for service or replacement.

4. If installing the water heater in a closed water system,

install an expansion tank in the cold water line as speci-

ﬁed under “Closed System/Thermal Expansion” (Page

16).

Total Hardness:

Chloride:

pH:

12 grains per gal. (205 mg/liter) max.

200 mg/liter max.

6.5-8.0

Alkalinity:

200 mg/liter max.

5. Install a shut-off valve in the cold water inlet line. It

should be located close to the water heater and be

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 15: Typical One-Temperature System Piping Installation

*100 Gallon Model Shown.

Tempering Valve Installation

Closed System/Thermal Expansion

A tempering valve has been provided for use with the

Polaris® Gas water heater and must be installed, per the

manufacturer’s instructions, in the domestic hot water line.

See Figure 16 for a sample tempering valve installation.

When a backflow prevention device or check valve is

installed, it can create a “Closed System.” Heating water

in a closed system causes normal thermal expansion and

increases pressure in the water system. When this pres-

sure reaches 150 psi, it triggers the safety system in the T

& P Relief Valve. This can result in the relief valve releas-

ing water during every cycle. The rapid and repeated

expansion and contraction of the water heater components

and the system piping can cause premature failure of the

relief valve, as well as the water heater itself. Replacing

the relief valve will not correct the problem.

General Information

Water piping, fittings, and valves must be properly installed

for the correct and safe operation of this water heater.

Please note the following:

•

The system should be installed only with piping that is

suitable for potable (drinking) water such as copper,

CPVC, or polybutylene. PVC water piping may be used

on the cold water inlet supply but not within 18 inches

of the cold water connection on the water heater.

Do not use PVC piping on the hot water outlet,

space heating supply, or space heating return.

Do not use any pumps, valves, or ﬁttings that are

not compatible with potable water.

If the water heater is installed in a closed water supply sys-

tem, such as one having a backflow preventer in the cold

water supply line, means shall be provided to control ther-

mal expansion. Contact the water supplier or local plumb-

ing inspector on how to control this situation.

•

A properly sized expansion tank must be installed to pre-

vent the water pressure from building to such a level in a

Closed System. The manufacturer of this water heater

will void the warranty if there is a failure to install a

properly sized expansion tank.

Do not use valves that may cause excessive

restriction to water ﬂow. Use full ﬂow ball or gate

valves only.

•

Do not use 50/50 tin-lead solder (or any lead based

solder) in potable water lines. Use 95/5 solder or

other equivalent material.

Do not tamper with the thermostat, gas valve,

blower, electrical components, or temperature and

pressure relief valve. Tampering with any of the

components is dangerous and can result in death,

severe injury, or property damage. Tampering voids

all warranties. Only qualiﬁed technicians should

service these components.

Do not use this water heater as a replacement for an

existing boiler installation.

Do not use with piping that has been treated with

chromates, boiler seal, or other chemicals.

Do not add any chemicals to the system piping

which will contaminate the potable water supply.

Combination Space Heating/Potable

Water System

Some water heater models are equipped with inlet/outlet

connections for use in space heating applications. If this

water heater is to be used to supply both space heating

and potable (drinking) water, the instructions listed below

must be followed (see ﬁgure 17).

•

Be sure to follow the manual(s) shipped with the air

handler or other type heating system.

This water heater is not to be used as a replacement

for an existing boiler installation.

Do not use with piping that has been treated with chro-

mates, boiler seal or other chemicals and do not add

any chemicals to the water heater piping.

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 17: Air Handler Piping Installation

Massachusetts code does not

allow this type of installation.

*100 Gallon Model Shown.

•

If the space heating system requires water temperatures Storage Tank Installation

in excess of 120°F, a tempering valve (provided) must

When installing the Polaris® with a storage tank, see figure

be installed per the manufacturer’s instructions in the

potable hot water supply to limit the risk of scald injury.

Pumps, valves, piping and ﬁttings must be compatible

with potable water.

A properly installed ﬂow control valve is required to pre-

vent thermosiphoning. Thermosiphoning is the result

of a continuous ﬂow of water through the air handler

circuit during the off cycle. Weeping (blow off) of the

temperature and pressure relief valve (T & P) or higher

than normal water temperatures are the ﬁrst signs of

thermosiphoning.

18 for piping suggestions.

•

Solar Installation

If this water heater is used as a solar storage heater or as

a backup for the solar system, the water supply tempera-

tures to the water heater tank may be in excess of 120°F.

A tempering valve must be installed in the water supply

line to limit the supply temperature to 120°F.

Note: Solar water heating systems can often supply water

with temperatures exceeding 180°F and may result in

water heater malfunction.

•

The hot water line from the water heater should be

vertical past any tempering valve or supply line to

the heating system to remove air bubbles from the

system.

Do not connect the water heater to any system or

components previously used with non-potable water

heating appliances when used to supply potable water.

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes on Figure 18:

Figure 18: Polaris with Auxillary Storage Tank - One or Two

Temperature System (With or Without Building Recirculation)

If tank temperature is set above

120°F and water is supplied for

domestic use (hand washing, show-

ering, etc.) a tempering valve must

be installed in the hot water line to

domestic fixtures.

Installation must conform to local

code requirements. If a check valve

is installed in the cold water sup-

ply line, an expansion tank must be

installed between the check valve

and the water heater’s cold water

inlet. Set storage tank temperature

five degrees lower than the water

heater’s temperature setting. Using

the plug cock in the recirculating

line, adjust the flow in the recirculat-

ing line to five gallons per minute.

*100 Gallon Model Shown.

Important: Only a new temperature and pressure relief

valve should be used with this water heater. Do not use

an old or existing valve as it may be damaged or not ade-

quate for the working pressure of the new water heater. Do

not place any valve or piping between the relief valve and

the tank.

Temperature and Pressure

Relief Valve

The Temperature & Pressure Relief Valve:

•

Must not be in contact with any electrical part.

Must be connected to an adequate discharge line.

•

Must not be rated higher than the working pressure

shown on the data plate of the water heater.

•

The BTUH rating of the T & P valve must be greater

than, or equal to, the input rating of the water heater

Explosion Hazard

The Discharge Line:

If the temperature and pressure relief valve

is dripping or leaking, have a qualified

service technician replace it.

•

Must not be smaller than the pipe size of the relief

valve or have any reducing coupling installed in the

discharge line.

•

Must not be capped, blocked, plugged or contain any

valve between the relief valve and the end of the dis-

charge line.

• Do not plug valve.

• Do not remove valve.

Failure to follow these instructions can

result in death or explosion.

•

Must terminate a maximum of 6 inches above a floor

drain or external to the building.

Must be capable of withstanding 250°F (121°C) without

distortion.

Must be installed to allow complete drainage of both

the valve and discharge line.

For protection against excessive pressures and tempera-

tures, a temperature and pressure relief valve must be

installed in the opening marked “T & P RELIEF VALVE”.

This valve must be design certified by a nationally recog-

nized testing laboratory that maintains periodic inspection

of the production of listed equipment or materials as meet-

ing the requirements for Relief Valves and Automatic Shut-

off Devices for Hot Water Supply Systems, ANSI Z21.22.

The function of the temperature and pressure relief valve is

to discharge water in large quantities in the event of exces-

sive temperature or pressure developing in the water heat-

er. The valve’s relief pressure must not exceed the working

pressure of the water heater as stated on the data plate.

Download from Www.Somanuals.com. All Manuals Search And Download.

GAS SUPPLY AND PIPING

Figure 19: Gas Piping Installation

Explosion Hazard

Use a new AGA or CSA approved gas

supply line.

Install a shut-off valve.

Do not connect a natural gas water

heater to a L.P. Gas Supply.

Do not connect an L.P. gas water heater

to a Natural Gas Supply.

Failure to follow these instructions can

result in death, explosion, or carbon

monoxide poisoning.

Gas Pressure

Important: The gas supply pressure must not exceed the

maximum supply pressure as stated on the water heater’s

data plate. Minimum supply pressure should also be

maintained per the data plate.

Gas Requirements

Read the data plate to be sure the water heater is made

for the type of gas being used. This information will be

found on the data plate located on the front of the water

heater. If the information does not agree with the type of

gas available, do not install or operate the water heater.

Call your dealer.

Note: An odorant may be added by the gas supplier to

the gas used by this water heater. This odorant may fade

over an extended period of time. Do not depend upon this

odorant as an indication of leaking gas.

Gas Piping

The gas piping must be installed according to all local and

state codes or in absence of local and state codes with

the “National Fuel Gas Code”, ANSI Z223.1 (NFPA 54)-

latest edition. Canadian installations must be performed in

accordance with CAN/CGA-B149. Note: If using a ﬂexible

gas connector, make sure its rating tag matches or exceeds

the input of the water heater.

Tables 2, 3A, and 3B on page 20 are provided as a sizing

reference for commonly used gas pipe materials. Consult

the “National Fuel Gas Code” for the recommended gas

pipe size of other materials. Follow the instructions below

and reference ﬁgure 19 for gas piping installation.

1. Install a readily accessible manual shut-off valve in the

gas supply line as recommended by the local utility.

Know the location of this valve and how to turn off the

gas to this unit. Note: DO NOT pipe across clean-out

port (100 gal. only.)

2. Install a drip leg as shown. The drip leg must be no

less than 3 inches long for the accumulation of dirt,

foreign material and water droplets.

3. Install a ground joint union between the water heater

and the manual shut-off valve. This is to allow easy

servicing.

4. Turn the gas supply on and check for leaks. Use a

chloride-free soap and water solution (bubbles forming

indicate a leak) or other approved method.

Note: Units with BTU/Hr inputs of 175,000 and above must

have a minimum of 3/4” NPT gas pipe supplied to the water

heater.

Download from Www.Somanuals.com. All Manuals Search And Download.

Gas Pressure Testing

Important: This water heater and its gas connection must

be leak tested before placing the appliance in operation.

•

If the code requires the gas lines to be tested at

a pressure of 14” W.C. or greater, the water heater

and its manual shut-off valve must be disconnected

from the gas supply piping system and the line

capped.

•

If the gas lines are to be tested at a pressure less

than 14” W.C., the water heater must be isolated

from the gas supply piping system by closing its

manual shut-off valve.

Explosion Hazard

Have a qualiﬁed person make sure L.P.

gas pressure does not exceed 13” water

column.

Examples of a qualiﬁed person include

licensed heating personnel, authorized

gas company personnel, and authorized

service personnel.

Nationally listed/recognized fuel gas and carbon

monoxide(CO) detectors are recommended in

all applications and should be installed using the

manufacturer’s instructions and local codes, rules, or

regulations.

Note: Air may be present in the gas lines and could prevent

the burner from lighting on initial start-up. The gas lines

should be purged of air by a qualified service technician

after installation of the gas piping system.

Failure to do so can result in death,

explosion, or ﬁre.

Download from Www.Somanuals.com. All Manuals Search And Download.

ELECTRICAL CONNECTIONS

4. Connect this circuit (directly from the electrical service

box) to an electrical disconnect switch.

5. Ground the water heater by connecting the electrical

service ground wire to the green ground wire (provided).

Electrical Shock Hazard

Disconnect power before

servicing.

Replace all parts and panels

before operating.

Note: The power supply to this water heater must be

properly polarized, [120 volts from the hot lead (black) to

ground and 0 volts from the neutral lead (white) to ground]

otherwise, the unit will not operate.

Failure to do so can result in

death or electrical shock.

6. After making all electrical connections, completely fill

the tank with water and check all connections for leaks.

Open the nearest hot water faucet and let it run for 3

minutes to purge the water lines of air and sediment

and to ensure complete filling of the tank. The electri-

cal power may then be turned on. See figure 20 for

completed installation.

If you lack the necessary skills required to properly install

the electrical wiring to this water heater, do not proceed but

have a qualified electrician perform the installation.

When making the electrical connections, always make

sure:

•

The voltage and frequency correspond to that specified

on the water heater data plate on the front of the water

heater.

Figure 20A: Electrical Connections (34/50 Gal.)

•

The electrical supply has the proper overload fuse

or breaker protection. The heater draws less than 7

amps.

•

Wire sizes and connections comply with all applicable

codes.

Wiring enclosed in approved conduit (if required by lo-

cal codes).

The water heater and electrical supply are properly

grounded.

This water heater must be “hard-wired” - do not use an

extension cord to supply electrical power to this water

heater.

Note:

The wiring diagram can be found on page 22. Always

reference the wiring diagram(s) for the correct electrical

connections.

Figure 20B: Electrical Connections (100 Gal.)

When installing the electrical wiring to the water heater:

1. Shut off the power at the electrical service box.

2. Loosen the screws securing the access panel to

the electrical compartment. (The electrical wiring

diagram for 34 & 50 gal. models can be found on the

inside of the access panel at the base of the water

heater. For 100 gal. models the wiring diagram is

located in the electrical compartment on the front of the

water heater.) Set the access panel aside.

3. Connect the electrical supply to the water heater in

accordance with local utility requirements and codes.

Use only a dedicated electrical circuit containing a

properly sized fuse or circuit breaker. Maximum over-

load protection should not exceed 15 amperes.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRING DIAGRAM

MODELS 130,000 BTU/Hr & Below

NEUTRAL

POWER SUPPLY

BLUE

RED

BLOWER

BLACK

TO 120/60

FUSED

DISCONNECT

GND

WHITE

GREEN

GND

BLOWER

RED

BROWN

GND

IND

GROUND

GREEN

NEUTRAL (WHITE)

HSI

TO 120/60

POWER

SUPPLY

GREEN

IGNITION

CONTROL

HSIG

IGNITER

RED

L1 (BLACK)

FUSED

DISCONNECTED

THERMOSTAT

SENSOR/ECO

BLACK

120 VAC

24 VAC

GAS VALVE

120 VAC

(BLACK & WHITE

WIRES IN BOLD)

IND

IGNITER

HSI

BROWN

WHITE

HSIG

RED

LED

POT

IGNITION

YELLOW

RED

CONTROL

PSI

PRESSURE

SWITCH

SEN-1

GREEN LED

120V/60Hz

THERMOSTAT

BOARD

PSI

LOWER

YELLOW

PSO

GAS VALVE

RELAY

GREEN

YELLOW

LED

FSG

PSO

GREEN

24V

HOT

IGNITION

CONTROL

COM

RELAY

ONLY

WHITE

COMMON (C)

RED

GREEN

LED

YELLOW LED

GND

BLUE

THERMOSTAT

SENSOR-ECO

PRESSURE

SWITCH

ORANGE

RED LED

YELLOW

N.O.

SEN-1

LOWER

NORMALLY OPEN

(NO)

ORANGE

COM

THERMOSTAT

24 V

THERMOSTAT

DIAL

BOARD

HOT

ONLY

NOTICE: IF ANY OF THE ORIGINAL WIRE

AS SUPPLIED WITH THE APPLIANCE

MUST BE REPLACED, IT MUST BE

REPLACED WITH 18 GAUGE STRANDED

105C WIRE OR ITS EQUIVALENT.

THERMOSTAT

DIAL

POT

GND

MODELS 150,000 BTU/Hr & Above

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION CHECKLIST

Water Heater Location

Requirements

Alternate Horizontal

ꢀ Correct relationship - outlet to inlet.

ꢀ 12” Min. above anticipated snow level.

ꢀ 2” exhaust outlet/air inlet pipe sloped down towards

water heater at 1/4” per foot. 3” piping sloped down

towards the heater at 1/8” per foot.

ꢀ Centrally located with the water piping system. Located

as close to the gas piping and vent pipe system as pos-

sible.

ꢀ Away from corners, other vents, windows, etc.

ꢀ Located indoors and in a vertical position. Protected

from freezing temperatures.

ꢀ Proper clearances from combustible surfaces main-

tained and not installed directly on a carpeted floor.

Sufficient room to service the water heater.

ꢀ Provisions made to protect the area from water dam-

age. Properly sized drain pan installed and piped to an

adequate drain.

Vertical

ꢀ Inlet - 12” Min. above roof/snow level.

ꢀ Correct relationship - outlet to inlet.

ꢀ Away from corners, other vents, windows, etc.

Concentric

ꢀ 12” Min. above grade/snow level.

ꢀ 2” exhaust outlet/air inlet pipe sloped down towards

water heater at 1/4” per foot. 3” piping sloped down

towards the heater at 1/8” per foot.

ꢀ Installation area free of corrosive elements and

flammable materials.

Condensate Line

ꢀ Drain stem is fully inserted in the elbow and glued

properly.

ꢀ Away from corners, other vents, windows, etc.

ꢀ Trap aligned so that the exhaust pipe is in a vertical

position close to the surface of the water heater.

ꢀ Line properly sloped to adequate drain or approved

condensate pump.

ꢀ Properly vented.

ꢀ Protected from freezing (if required).

Water System Piping

ꢀ Temperature and pressure relief valve properly

installed with a discharge line run to an open drain and

protected from freezing.

ꢀ All piping properly installed and free of leaks.

ꢀ Heater completely filled with water.

ꢀ A properly sized expansion tank must be installed on all

closed systems.

ꢀ A tempering valve (provided) must be installed per the

manufacturer’s instructions.

Vent Pipe System

ꢀ Vent pipe and fittings of approved material.

ꢀ Acceptable size, length, and number of elbows on air

inlet pipe.

ꢀ Acceptable size, length, and number of elbows on

exhaust outlet pipe.

ꢀ Add the air inlet filter per the manufacturer’s instruction.

ꢀ Installed in accordance with prevailing provisions of

Local codes, or in the absence of such, National Fuel

Gas Code, NFPA 54, ANSI Z223.1-Latest Edition. Ca-

nadian Installations must be performed in accordance

with CAN/CGA-B149.

ꢀ All 2” horizontal piping sloped down toward the water

heater at 1/4” per foot. 3” piping sloped down towards

the heater at 1/8” per foot.

Gas Supply and Piping

ꢀ If using a flexible gas connector, make sure its rating

tag matches or exceeds the input of the water heater.

ꢀ Adequate pipe size and of approved material.

ꢀ Gas supply is the same type as listed on the water

heater data plate.

ꢀ Gas line equipped with full opening shut-off valve,

union and drip leg.

ꢀ Approved pipe joint compound used.

ꢀ Chloride-free soap and water solution or other ap-

proved means used to check all connections and fit-

tings for possible gas leaks.

ꢀ Not obstructed in any way.

Vent Termination

Electrical Connections

Horizontal

ꢀ Unit connected to a dedicated power supply.

ꢀ Unit connected to a 120V electrical supply.

ꢀ Proper polarity.

ꢀ Correct relationship - outlet to inlet.

ꢀ 12” Min. above grade/snow level.

ꢀ 2” exhaust outlet/air inlet pipe sloped down towards

water heater at 1/4” per foot. 3” piping sloped down

towards the heater at 1/8” per foot.

ꢀ Water heater properly grounded.

ꢀ Installed in accordance with prevailing provisions of

local codes, or in the absence of such, National Fuel

Gas Code, NFPA 54, ANSI Z223.1-Latest Edition.

Canadian installations must be performed in accor-

dance with CAN/CGA-B149.

ꢀ Away from corners, other vents, windows, etc.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING YOUR WATER HEATER

Read and understand these directions thoroughly before

attempting to operate the water heater (see Operating

Instructions on page 25). Check the data plate on the front

of the water heater for the correct gas. Do not use this

water heater with any gas other than the one listed on the

data plate. If you have any questions or doubts, consult

your gas supplier or gas utility company.

When the thermostat calls for heat, the blower will run for

6 seconds to purge the system of any accumulated gas or

air. The hot surface igniter will heat up for 35 seconds. The

blower will turn on and the gas valve open, forcing the air

and gas mixture across the hot surface igniter, causing the

burner to light. The hot surface igniter will turn off and act

as an electronic flame sensor to determine if burner ignition

has been accomplished. If it detects any loss of flame, it

will shut off the gas supply to the burner.

L.P. (Propane) Models

Propane gas is heavier than air and in the occurrence of

a leak in the system, the gas will settle on the floor level.

Basements, crawl spaces, skirted areas under mobile

homes (even when ventilated), closets and areas below

ground level will serve as pockets for the accumulation of

gas. Before lighting a propane gas water heater, smell all

around the appliance at floor level. If you smell gas, follow

the instructions as given in the warning on the front page.

The ignition control will try to light the burner three times.

If the ignition control does not detect a flame after three

tries, it will temporarily lock out, but then auto restart and go

through three additional tries for ignition after 60 minutes.

It will repeat until ignition occurs or the system locks out

requiring service. Refer to Troubleshooting Guide on Page 28.

Thermostat Sensor

The sensor is a 10K ohm at 77°F (25°C) thermistor. Read

resistance through the black wires that run to the sensor.

Remove wires from circuit board before checking. An

open or short circuit indicates sensor failure. Check

reading against the following table. The resistance should

correspond with the temperature in the tank:

When your propane tank runs out of fuel, turn off the gas

at all gas appliances including pilot lights. After the tank

is refilled, all appliances must be re-lit according to their

manufacturer’s instructions.

Water Heater Operation

This appliance does not have a pilot light. It is equipped

with an electronic ignition that automatically lights the

burner. There are three lights to indicate the various stages

of operation; Green = Electrical power is on, Yellow =

Thermostat is calling for heat, which signals the beginning

of the ignition sequence (see figure 21), and Red = Ignition

control is signaling the gas valve to open.

60°F

80°F

16°C

27°C

38°C

49°C

60°C

71°C

85°C

15,300 ohms

9,300 ohms

5,800 ohms

3,800 ohms

2,500 ohms

1,700 ohms

1,100 ohms

100°F

120°F

140°F

160°F

185°F

Figure 21: Sequence of Operation

Download from Www.Somanuals.com. All Manuals Search And Download.

The thermostat is adjusted to its lowest temperature setting

when it is shipped from the factory. Water temperature

can be regulated by moving the temperature dial to the

preferred setting. The preferred starting point is 130°F;

however, in some instances, setting the water heater higher

than 130°F can reduce the occurrence of igniter failure due

to excessive condensate.

Stacking

Stacking occurs when a series of short draws of hot water

(3 gallons or less) are taken from the water heater tank.

This causes increased cycling of the burner and can result

in increased water temperatures at the hot water outlet. A

tempering valve must be installed in the hot water supply

line to reduce the risk of scald injury.

Important: A tempering valve (provided) must be installed

in the hot water outlet to reduce the risk of scald injury

when setting the thermostat in excess of 120°F.

Water Temperature Regulation

Many home heating systems used with this water heater

are designed for temperatures higher than 130°F. Refer to

the manufacturer’s instruction manuals supplied with this

type of equipment for recommended temperature settings.

Important: Adjusting the thermostat past the 120°F setting

on the temperature dial (see figure 22) will increase the

risk of scald injury. Hot water can

produce first degree burns within:

120°F (49°C) more than 5 minutes

Figure 22:

Temperature Dial

130°F (54°C) at 20 seconds

140°F (60°C) at 3 seconds

Water temperature over 125°F can cause severe

burns instantly or death from scalds.

150°F (66°C) at 1-1/2 seconds

160°F (71°C) at less than 1 second

Children, disabled and elderly are at highest

risk of being scalded.

See instruction manual before setting

temperature at water heater.

Feel water before bathing or showering.

Temperature limiting valves are available.

Emergency Shut Down

Important: If overheating occurs or

the gas supply fails to shut off, close

the manual gas supply valve. Turn off the electrical supply to

the unit and close the cold water supply valve. Do not operate

the water heater again until it has been thoroughly checked by

an authorized service technician.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONAL CONDITIONS

Water Heater Sounds

Figure 23: Hand Hole Clean-out

During the normal operation of the water heater, sounds or

noises may be heard. These noises are common and may

result from the following:

1. Normal expansion and contraction of metal parts

during periods of heat-up and cool-down.

2. Sediment buildup in the tank bottom will create varying

amounts of noise and may cause premature tank fail-

ure. Drain and flush the tank as directed under “Drain-

ing and Flushing”.

Safety Shut-Off (Pressure Switch)

This water heater is equipped with a pressure switch that

protects the unit by shutting it down in the event that:

•

A blockage occurs in the combustion air inlet, the

flue gas exhaust outlet, or both the inlet and outlet.

The condensate line freezes and the condensate

“backs up” and fills the exhaust outlet.

•

The blower fails to operate, or operates improperly.

The unit begins to operate at an abnormally low

input level.

Energy Cut-Off (ECO)

8. Remove screw holding the outer hand hole clean-out

cover. Then carefully remove the insulation covering

the clean-out plug. Using a 1/2” square drive ratchet

open the clean-out plug (see ﬁgure 23.) Note: After

removing the clean-out plug inspect the O-ring for dam-

age, replace if necessary.

Ahigh temperature limit switch, or ECO, is used to shut down

the water heater if the water temperature exceeds 203°F.

The ECO will automatically reset when the temperature cools

sufficiently. If the ECO shuts down the heater repetitively,

contact a qualified professional for service.

9. Using a Wet/Dry shop vacuum clean any debris from

the tank.

10. Lubricate O-ring with a food grade oil. Then replace

and securely tighten the clean-out plug.

11. Replace the insulation and cover plate.

12. Close the drain valve, replace access door, reﬁll

the tank, and restart the heater as directed under

“Operating Your Water Heater”.

If the water heater is going to be shut down for an extended

period, the drain valve should be left open.

MAINTENANCE

Draining and Flushing

It is recommended that the tank be drained and flushed

every 6 months to remove sediment which may buildup

during operation. The water heater should be drained if

being shut down during freezing temperatures.

To drain the tank, perform the following steps:

Turn off the gas supply at the Manual Gas Shut-off

Valve. Turn off the electrical supply to the water

heater

Temperature and Pressure

Relief Valve

Close the cold water inlet valve.

Open a nearby hot water faucet.

Figure 24

Manually operate the

temperature and pressure

relief valve at least once

a year to make sure it is

working properly. To prevent

water damage, the valve

must be properly connected

to a discharge line which

terminates at an adequate

drain. Standing clear of

the outlet (discharged

Open the access door at the bottom of the heater,

then connect a hose to the drain valve and

terminate it to an adequate drain.

Note: The drain hose should be rated for at least 200°F.

If the drain hose does not have this rating, open the cold

water inlet valve and a nearby hot faucet until the water is

no longer hot.

5. Close the cold water inlet valve.

6. Open the water heater drain valve and allow all

the water to drain from the tank.

7. Flush tank to remove sediment

Note: For water heaters with a hand hole clean-out follow

steps 8-11.

water may be hot), slowly

lift and release the lever handle on the temperature and

pressure relief valve to allow the valve to operate freely

and return to its closed position (see figure 24). If the valve

fails to completely reset and continues to release water,

immediately shut off the manual gas valve and the cold

water inlet valve, and call a qualified service technician.

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE OF YOUR WATER HEATER

3 Month Inspection

At least every 3 months, a visual inspection should be

made of the combustion air inlet as well as the exhaust and

water piping. Check the water heater for the following:

Replacing the Gas Valve

Important: The rubber gasket that seals the gas valve to

the venturi manifold must be used (previous gaskets may

be reused, if in good condition). Make sure the gasket is

properly inserted into the recess on the gas valve prior to

installation (see figure 25 for exact placement of the rubber

gasket).

•

Obstructions, damage, or deterioration in the venting

system. Make sure the exhaust and combustion air

supplies are not obstructed.

1. Remove the O-ring from the flange (removed from the

old gas valve) and replace it with the one provided

in the gas valve kit (model VK8115V, part number

6903775.)

2. Reattach the elbow flange to the gas valve. Tighten all

four screws securely.

3. Place the three T-25 Torx screws through the proper

holes in the venturi manifold flange. See figure 25.

4. Properly install a new rubber gasket (provided) as

shown in figure 25.

•

Leaking or damaged water and gas piping.

Presence of ﬂammable or corrosive materials in the

installation area.

•

Presence of combustible materials near the water

heater.

Important: Verify proper operation after servicing this water

heater.

5. Position the gas valve and start all three screws

(projecting downward from the venturi manifold) into

the gas valve. A T-25 Torx wrench has been provided

in the gas valve replacement kit (model VK8115V, part

number 6903775.)

Note: All three T-25 Torx screws must be properly tightened

to secure the seal between the gas valve and the venturi

manifold.

Gas Valve

The gas valve on this water heater has been permanently

set at the factory for proper operation. No field adjustments

are needed and none should be performed.

Removing the Gas Valve

Removal and replacement of the gas regulator valve

involves the disconnection of gas piping and electrical

leads. This procedure must be performed by a qualified

service technician.

6. Reconnect the pressure tap to the port on the new gas

valve (see figure 25).

7. Reconnect the external gas supply line to the gas pip-

ing on the gas valve. Be sure to use approved Teflon

tape or pipe joint compound suitable for gas piping.

Note: Use a second pipe wrench on the gas piping inside

the skirt to avoid cracking the gas valve or the cast fitting.

8. Reconnect the electrical plug to the gas valve and

secure it with the screw provided.

9. Turn gas supply on and check for leaks. Use a chlo-

ride-free soap and water solution (bubbles forming

indicate a leak) or other approved method. All leaks

must be fixed immediately.

10. Be sure tank is completely filled with water before re-

storing power to the water heater. Follow operating

instructions on Page 25.

11. Ensure proper operation of the water heater, then rein-

stall the access door.

Important: When removing the gas valve, do not use a

pipe wrench or vise to grip the body. Do not apply any force

to the gas valve or the cast flange fitting on the inlet side

of the gas valve (see figure 25.) Such force may break or

crack these components.

1. Turn temperature dial counterclockwise to the lowest

setting and turn off electrical power to appliance.

2. Shut off the gas at the manual shut-off valve on the

gas supply line. See figure 19 for reference. Remove

the access door.

3. Disconnect the gas piping connection just outside

the base of the water heater . Note: Use a second

pipe wrench on the gas piping inside the skirt to avoid

cracking the gas valve or the flange fitting.

If additional information is required, contact the Product

Service and Support Group at 1-800-456-9805.

4. Remove the pressure tap from the gas valve (see

figure 25). The hose should not be disconnected.

5. Remove the Phillips head screw holding the electrical

plug and remove electrical plug from the gas valve.

6. Remove the three T-25 Torx head brass screws that

attach the gas valve to the venturi manifold, using

the T-25 Torx wrench supplied with the gas valve kit

(model VK8115V, part number 6903775.)

Figure 25

7. Remove the gas valve from the unit keeping the

rubber gasket with the gas valve .

8. Remove the flange from the gas inlet side of the valve

by removing the four (4) attachment screws.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Ignition Control Module (ICM) LED Error Codes: (Flashes visible through viewport in access door)

FLASHES

INDICATED PROBLEM

Pressure Switch Closed

Pressure Switch Open

Failed Ignition

CONTROL REACTION

SC*

SL3

Gas Valve Hardware Fault

Flame Sense Hardware Fault

False Flame

SL**

Ignition Control Hardware Fault

Ignition Control Software Fault

L1 Polarity Detection

Rapid

SL (Soft Lockout): Control Automatically resets after 60 minutes.

SL3 (Soft Lockout/Hard Lockout): Control automatically resets after 60 minutes, with a maximum of 3 resets, followed by hard lockout requiring service.

SC (Self Clearing): Control will function normally as soon as it no longer detects the previously indicated fault.

* when pressure switch or blower relay opens

** when ﬂame is no longer sensed.

† Blower Isolation Relay is used on models 150,000 BTU/Hr and above.

Note: If unit goes into a soft or hard lock-out the ignition control module can be reset by cycling power to the water heater.

Download from Www.Somanuals.com. All Manuals Search And Download.

SOFTWARE OPERATION SEQUENCE

IGNITION CONTROL MODULE SOFTWARE OPERATION SEQUENCE

* For 175,000 BTU/Hr models and above the flame establishing period is six seconds. For the first 3 seconds the gas valve is off.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS LIST/DIAGRAM

31B

ALL MODELS EXCEPT

100 GALLON

When ordering repair parts always give the

following information:

Model, serial, and product numbers

Type of gas

Item number

Parts description

Repair Parts List

ITEM

NO.

PARTS DESCRIPTION

31A

1” NPT x 3” BRASS NIPPLE

THERMOSTAT SENSOR BUSHING

O-RING

THERMOSTAT SENSOR/ECO

INVERTED FLARE NUT

PLUG

VINYL TUBING

PRESSURE SWITCH

COMBUSTION BLOWER

4 INCH DIAMETER BLOWER GASKET

BURNER (NATURAL AND L.P. SAME)

6 INCH DIAMETER BURNER GASKET

HOT SURFACE IGNITER

IGNITER BRACKET

TOOLS REQUIRED FOR SERVICING

31A

31B

TOOL

FUNCTION

VOLT OHMMETER

MEASURE VOLTAGE/RESISTANCE

CLAMP-ON AMMETER

STOPWATCH

MEASURE CURRENT

CLOCK GAS CONSUMPTION

CALCULATE INPUT RATE

READ INLET GAS PRESSURE

CONNECT MANOMETER

VENTURI MANIFOLD

CALCULATOR

REDUCING COUPLING

AIR INLET PIPE ASSEMBLY

GAS VALVE

1/2” NPT 90 DEGREE INLET FLANGE

1/2” NPT X 2” NIPPLES

1/2” NPT ELBOWS

1/2” NPT X 4.5” NIPPLE

RED LED

YELLOW LED

U-TUBE MANOMETER

3/16” ID PLASTIC TUBING - 2 FT

#1 & #2 PHILLIPS SCREWDRIVERS REMOVE DOORS AND CONTROLS

12” PIPE WRENCH (2 REQUIRED)

1/2” COMBINATION WRENCH

1/2” SOCKETAND RATCHET

REMOVE GAS LINE

REMOVE BLOWER AND BURNER

3/8” COMBO WRENCH/NUT DRIVER REMOVE IGNITER

T-25 TORX WRENCH REMOVE THE GAS VALVE

(ALSO HELPFUL - 9/32” and 5/16” COMBINATION WRENCHES)

GREEN LED

THERMOSTAT BEZEL

TEMPERATURE SELECTOR KNOB

THERMOSTAT BOARD

IGNITION CONTROL

TRANSFORMER

2” CONDENSATE TRAP ASSEMBLY

3” CONDENSATE TRAP ASSEMBLY

COLD WATER TUBE ASSEMBLY

TEMPERATURE AND PRESSURE RELIEF VALVE

DRAIN VALVE

POTENTIOMETER

VENTURI GASKET (not pictured)

BLOWER ISOLATION RELAY (150,000+ BTU/Hr)

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS LIST/DIAGRAM

100 GALLON MODELS

When ordering repair parts always give the

following information:

Model, serial, and product numbers

Type of gas

Item number

Parts description

Repair Parts List

ITEM

NO.

PARTS DESCRIPTION

1-1/2” NPT x 3” BRASS NIPPLE

THERMOSTAT SENSOR BUSHING

THERMOSTAT SENSOR/ECO

CONTROL PANEL HOUSING

IGNITION CONTROL

BLOWER ISOLATION RELAY

THERMOSTAT BOARD

TRANSFORMER

SIGHT GLASS

RED LED

TOOLS REQUIRED FOR SERVICING

YELLOW LED

GREEN LED

TOOL

VOLT OHMMETER

CLAMP-ON AMMETER

STOPWATCH

CALCULATOR

U-TUBE MANOMETER

3/16” ID PLASTIC TUBING - 2 FT

#1 & #2 PHILLIPS SCREWDRIVERS REMOVE DOORS AND CONTROLS

12” PIPE WRENCH (2 REQUIRED)

1/2” COMBINATION WRENCH

1/2” SOCKETAND RATCHET

3/8” COMBO WRENCH/NUT DRIVER REMOVE IGNITER

T-25 TORX WRENCH REMOVE THE GAS VALVE

(ALSO HELPFUL - 9/32” and 5/16” COMBINATION WRENCHES)

FUNCTION

MEASURE VOLTAGE/RESISTANCE

MEASURE CURRENT

CLOCK GAS CONSUMPTION

CALCULATE INPUT RATE

READ INLET GAS PRESSURE

CONNECT MANOMETER

TEMPERATURE SELECTOR KNOB

THERMOSTAT BEZEL

POTENTIOMETER

PRESSURE SWITCH

VINYL TUBING

ACCESS PANEL

CLEAN-OUT PLUG w/O-RING

CONDUIT

3” CONDENSATE TRAP ASSEMBLY

BUSHING

AIR INLET PIPE ASSEMBLY

3/4” GAS INLET PIPE

PIPE COUPLING

GAS VALVE

VENTURI MANIFOLD

IGNITER BRACKET

REMOVE GAS LINE

REMOVE BLOWER AND BURNER

HOT SURFACE IGNITOR

BLOWER

4” DIAMETER BLOWER GASKET

BURNER (NATURAL & L.P. SAME)

6” DIAMETER BURNER GASKET

DRAIN VALVE

TEMPERATURE AND PRESSURE RELIEF VALVE

Download from Www.Somanuals.com. All Manuals Search And Download.

POLARIS MODELS & DIMENSIONS

34/50 Gallon Units

100 Gallon Units

Clean-out Port

AIR

WATER

CONNECTIONS

T&P

HGT

GAS

INLET/

INPUT

(MBTU

CAP. PER HR.)

APPROX

SHIP.

WEIGHT

EXTERIOR

SUPPLY EXHAUST

MODEL

NUMBER

GAL.

VENT

DIA.

PG10 34-100-2NV OR 2PV

PG10 34-130-2NV OR 2PV

PG10 50-130-2NV OR 2PV

PG10 34-150-2NV OR 2PV

PG10 50-175-3NV OR 3PV

PG10 50-199-3NV OR 3PV

PG10 100-199-3NV OR 3PV

100

130

150

175

199

2 OR 3

48-1/2

62-3/8

48-1/2

63-3/4

15-3/4

23-1/4

40-1/2

54-1/2

40-1/2

55-3/4

56-1/4

6-3/8

5-1/2 / 6-5/8

8-1/2 / 6-3/4

150

176

150

180

468

56-1/4

100

Download from Www.Somanuals.com. All Manuals Search And Download.

Peavey Musical Instrument Amplifier TNT 115S BW User Manual
Pella Window 801W0103 User Manual
Philips All in One Printer MWE1221T User Manual
Philips Cell Phone SE735 User Manual
Philips MP3 Docking Station 26PFL3321S User Manual
Philips Power Supply LR20EB4A User Manual
Philips TV DVD Combo 20MC4206 User Manual
Phoenix Gold Speaker AudioSource User Manual
Poulan Blower 530087725 User Manual
Poulan Snow Blower 183615 User Manual