Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
IMPORTANT INFORMATION
Warnings and Notices
When using electrical equipment, basic safety precautions should always be followed including the following:
a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b. Do not use outdoors.
c. Do not mount near gas or electric heaters.
d. Equipment should be mounted in locations and at heights where it will not readily be subjected to
tampering by unauthorized personnel.
e. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
f. Do not use this equipment for other than intended use.
g. Refer service to qualified personnel.
SAVE THESE INSTRUCTIONS.
WARNING: You must have access to a main circuit breaker or other power disconnect device
before installing any wiring. Be sure that power is disconnected by removing fuses or turning the
main circuit breaker off before installation. Installing the device with power on may expose you to
dangerous voltages and damage the device. A qualified electrician must perform this installation.
WARNING: Refer to National Electrical Code® and local codes for cable specifications. Failure to
use proper cable can result in damage to equipment or danger to personnel.
WARNING: This equipment is intended for installation in accordance with the National Electric
Code® and local regulations. It is also intended for installation in indoor applications only. Before
any electrical work is performed, disconnect power at the circuit breaker or remove the fuse to avoid
shock or damage to the control. It is recommended that a qualified electrician perform this
installation.
Additional Resources for DMX512
For more information on installing DMX512 control systems, the following publication is available for purchase
from the United States Institute for Theatre Technology (USITT), "Recommended Practice for DMX512: A Guide
for Users and Installers, 2nd edition" (ISBN: 9780955703522). USITT Contact Information:
USITT
315 South Crouse Avenue, Suite 200
Syracuse, NY 13210-1844
Phone: 1.800.938.7488 or 1.315.463.6463
Philips Selecon Limited Three-Year Warranty
Philips Selecon offers a three-year limited warranty of its luminaires against defects in materials or workmanship
from the date of delivery. A copy of the Philips Selecon three-year limited warranty containing specific terms and
Philips Selecon office.
PLCYC LED Luminaire’s powerful LED engine offers exceptional performance and life. Under normal operating
conditions, our LED engine has a life expectancy in excess of 50,000 hours, however under worst case operating
conditions with the luminaire set to continuous full output it is possible that a small percentage of LED’s may
require replacement sooner. The Philips Selecon three-year limited warranty includes our guarantee against
premature failure of the LED engine.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
TABLE OF CONTENTS
Philips Selecon Offices........................................................................................................................... Inside Front Cover
Warnings and Notices......................................................................................................................................................... 1
PLCYC LED Luminaire Wireless DMX512 Receivers..................................................................................................... 3
PLCYC LED Luminaire Components........................................................................................................................................ 4
Power Requirements................................................................................................................................................................... 6
LCD Menu Operation................................................................................................................................................................. 9
Security ..................................................................................................................................................................................... 13
Presets ....................................................................................................................................................................................... 14
Setting Options & Descriptions........................................................................................................................................ 15
16-Bit Mode.............................................................................................................................................................................. 17
8-Bit Mode................................................................................................................................................................................ 19
PLCYC LED Luminaire DMX Timing Channel Detail........................................................................................................... 22
Special Cleaning and Care Instructions.................................................................................................................................... 28
Service and Maintenance.......................................................................................................................................................... 28
PLCYC LED Luminaire Dimensions....................................................................................................................................... 31
2
TABLE OF CONTENTS
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
PREFACE
1. About this Manual
The document provides installation and operation instructions for the following products:
• PLCYC LED Luminaire (PLCYC1-03).
Please read all instructions before installing or using this product. Retain this manual for future reference. Additional
Note: All PLCYC LED Luminaires are universal voltage (100VAC to 240VAC, Auto-ranging).
2. Accessories
Contact your Authorized Philips Selecon Dealer for price and availability of all accessories for PLCYC LED
PLCYC LED Luminaire Wireless DMX512 Receivers
Part Number
Description
PLCYC1WDMX03
W-DMX Wireless DMX512 Receiver (Wireless Solutions) Black
PLCYC LED Luminaire Wireless DMX512 Transmitters
Part Number
Description
PL1WDMXTR
W-DMX Wireless DMX512 Transmitter
PLCYC LED Luminaire USB Luminaire Software Cable
Part Number
Description
USB Luminaire Software Programming Kit (for updating or reloading luminaire software only) - include
USB to DMX dongle, Uploader Program, and Carry Bag
PLUPLD
About this Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
PLCYC LED LUMINAIRE OVERVIEW
1. PLCYC LED Luminaire Components
Major Luminaire Components
4
2
3
Rear of Unit
Front of Unit
1
1) PLCYC LED Luminaire Head
3) Tilt Axis Point / Locking Handle
4) Yoke / Mounting Point
Figure 1: PLCYC LED Luminaire Components
Luminaire Connections and LCD Display
Rear View
E
B
A
B
C
D
E
PowerCon (AC) Input
PowerCon (AC) Output
DMX512 Input
A
F
D
G
DMX512 Output / Thru
Yoke Assembly
C
F
Yoke Adjustment / Locking Knob
LCD Display & Menu System
G
Figure 2: PLCYC LED Luminaire - Rear View
4
PLCYC LED LUMINAIRE OVERVIEW
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
LCD Display / Menu System
3
1
2
1) LCD Display (Menu System)
2) Preset / Intensity / Menu Access Buttons
3) Function (Menu System) Select Push Buttons
Note: For Menu operation and programming details,
Figure 3: PLCYC LED Luminaire LCD Display & Menu System
PLCYC LED Luminaire Components
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
INSTALLATION AND SET UP
1. Power Requirements
The PLCYC LED Luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire contains an
auto-ranging power supply. Depending on supply voltage, each luminaire can draw up to 1.5 amps.
Table 1: PLCYC LED Luminaire Voltage vs. Current
Maximum
number of
units that can
be linked
Maximum
number of
units that can
be linked
Voltage
(AC)
Total
Current (A)
Voltage
(AC)
Total
Current (A)
together*
together*
100
110
120
130
140
150
160
170
1.50
1.36
1.25
1.15
1.07
1.00
0.94
0.88
13
14
16
17
18
20
21
22
180
190
200
210
220
230
240
0.83
0.79
0.75
0.71
0.68
0.65
0.63
24
25
26
28
29
30
32
WARNING! *These figures are based on the Maximum Allowable Input Current of 20 Amps (and the maximum
power supply limit of 150 Watts). Do not overload circuits!
2. Connecting Power
Units can be powered in one of two ways:
• Direct connection to a AC power source using an AC input cable.
• Daisy chain connection using a interconnect AC cable.
AC Output Connection
AC Input Connection
(to next luminaire, optional)
IMPORTANT AC POWER CONNECTION NOTES:
a. When using the daisy-chain connection method, ONLY connect PLCYC LED Luminaires
to AC Output Connection of PLCYC LED Luminaires. DO NOT CONNECT OTHER TYPES
OF LUMINAIRES OR DEVICES!
b. Use only use approved cable types.
c. Do not overload circuits!
d. Do not connect PLCYC LED Luminaires to dimmed circuits.
e. The MAXIMUM allowable number of PLCYC Luminaires which can be 'daisy-chained' on
6
INSTALLATION AND SET UP
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
If the unit is supplied with an AC input cable but you did not order an AC input connector, Table 2 describes how to
connect power to your PLCYC LED Luminaire. Field wiring of the PLCYC LED Luminaire is straight forward. A
total of 3 wires/conductors need to be brought to the unit. The following wiring scheme is required:
Table 2: PLCYC LED Luminaire AC Input Connections
Wire Colour
Purpose
Brown
Blue
Main / Line (100 to 240VAC)
Neutral
Ground
Green/Yellow
3. Connecting to the DMX512 Network
Basic DMX512 installation consists of connecting multiple PLCYC LED Luminaires together (up to 32 luminaires)
in "daisy-chain" fashion. A cable runs from the control console (or DMX512 control source) to the DMX connector
on the first PLCYC LED Luminaire. Another cable runs from the other DMX connector on the first unit to a DMX
connector on the next PLCYC LED Luminaire (or DMX512 device to be controlled).
Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on
PLCYC LED Luminaires
DMX512
(from console or
control device)
DMX512 (out from first
to second luminaire)
DMX512 (out to the next luminaire or DMX512
controlled device)
DMX512 Connections
DMX512 Signal
Common (Drain)
DMX512 -
XLR Pin
1
2
3
DMX512 +
Note: Remaining pins on each connector are not used.
Figure 4: PLCYC LED Luminaires - DMX512 Connections
Connecting to the DMX512 Network
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
4. Mounting
PLCYC LED Luminaires offer a plastic monocoque
yoke design for mounting by theatrical clamps or
hooks (sold separately).
For optimum performance and use, PLCYC LED
Luminaires should be mounted and spaced as shown
S
• S = Spacing between fixtures
D
• D = Distance from fixture to projection surface.
• A ratio of S = D x 0.9 is the formula used to cal-
culate the optimum spacing for these fixtures.
WARNING! Before attempting any installation or
service, disconnect all power at power source.
Turning off the output of the luminaire does not
disconnect power. Installation and service should
only be performed by a trained and qualified
professional. Be sure to check circuit capacity
before installing luminaires.
Figure 5: PLCYC LED Luminaire Hanging / Spacing
5. Tilt Adjustments
To adjust luminaire tilt position:
9.5 in. /
240.4 mm
1.2 in. /
30.2 mm
Yoke Assembly
6.7 in. /
170.5 mm
Tilt Locking
Handle
R 5.7 in. /
143.5 mm
Luminaire
R 7.7 in. /
195.0 mm
Head Assembly
Figure 6: Tilt Adjustments
Step 2. Position tilt (up or down) luminaire head assembly as desired.
Step 3. Hand-tighten, but do not over tighten, tilt locking handle.
8
INSTALLATION AND SET UP
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
OPERATION AND PROGRAMMING
1. LCD Menu Operation
The PLCYC LED Luminaire’s LCD Display and Menu System provides local control for accessing all the fixture’s
status information, menu options, and settings.
Note: If there are multiple luminaires in a system, changes would need to be made at each LCD Menu as desired.
Upon power up, the LCD will display the main screen showing the product type/name. If DMX is enabled, the
programmed address will appear after power up.
LCD Display -
Escape Button -
Displays all menu parameters and
Enters menu options. Navigates
option settings. Also displays DMX512
(backs up) one menu level.
address.
PRESET Button -
Allows the recall of
stored presets.
INTENSITY Button -
Allows the customization of current
intensity (light output). Note, using the
LEFT and RIGHT arrow buttons you can
select each RGBW channel individually
and change their intensity using the UP
and DOWN arrows.
Up/Down/Left/Right Arrow Buttons -
Navigates menu system and used for
selecting and setting options.
OK (Enter) Button -
Accesses details, activates
a field, or enters a setting
depending on the current menu item.
Figure 7: LCD Display and Menu System
LCD Menu Operation
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
2. LCD Menu System
The LCD Display Menu system consists of several categories. Use the four arrow buttons as required (refer to Figure
7 on page 9) to access and make changes to the menu items. When the desired menu item is reached, press [OK] to
display the menu options. Use navigation and [OK] buttons to view status and configure the LCD Menu as required.
Note: Depending on the security settings, certain menu items may be password protected. You must have the set
PassPIN in order to access these items. Locked items will have a "Key" icon displayed next to them.
To navigate and access menu settings/selections:
Step 1. At Main Menu, press [ESC] / [MENU] button once. A small window will appear over Main Menu with sub-
menu categories:
a. Save as Preset
b. Edit a Preset
c. Color Mix
d. Fan Control
e. Settings
f. Lock Fixture
g. Enter Password
h. LED Status
Step 2. Press [OK] at desired menu item to access and make changes.
Step 3. Make changes as desired.
Note: For complete menu structure and available options, see "Menu Structure (continued)" on page 12.
Note: When DMX512 signal is present, Edit Preset and Color Mix options will not appear in menu structure.
To navigate fixture status menus:
Step 1. At Main Menu, press LEFT or RIGHT arrow button once. Main menu screen will change to fixture status
screen will appear as follows (note, depending on which arrow button is pressed, status screens may appear
in reverse order):
a. DMX Address (note, if fixture is UNLOCKED, hit [OK] to change DMX address)
b. Fixture Hours (displays fixture operating hours since last reset)
c. Fixture Power (displays Max Power Limit setting (in Watts), Present Power consumed by fixture (in
Watts), and Hours of Use)
d. Fixture Status (displays current operational temperature, LED status, and fan speed setting)
Step 2. Press LEFT or RIGHT arrow buttons to scroll through status screens.
Step 3. Press [ESC] at anytime to access menu settings. See "To navigate and access menu settings/selections:" on
10
OPERATION AND PROGRAMMING
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Menu Structure
Installation & User’s Manual
LCD Display /
Menu System
MAIN MENU
Save as Preset
Sub Menu
Options
Comments
Users can:
Off
•
Save the current settings (look) to
a specific recallable Preset in the
Scratch Pad
Warm White*
Cool White*
Day Light*
Select Preset to Save - (Option)
fixture’s memory.
•
Edit the levels (values) for Red,
Green, Blue, White, and Intensity
values (in percent%) by using the
arrow buttons. Once the values
are adjusted, the preset is saved
as desired.
Scrolls and sets current user-defined
colour mix to various recallable
presets in the fixture using arrow
buttons.
Note: To edit a current (set) preset,
see Edit Presets.
*Only intensities may be stored on
White colour Temperature presets.
RGBW in these presets cannot be
edited or changed.
Preset X (5 through 31)
Continued next page
Note: See "To navigate and access menu settings/selections:" on page 10 to learn how to access menus. To save
changes, hit [OK]. Press [ESC] to cancel any changes you made.
LCD Menu System
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
Menu Structure (continued)
Continued from previous page
Edit a Preset
Sub Menu
Options
Comments
Users can:
Off
•
Edit the current settings (look) to a
specific recallable Preset in the fix-
ture’s memory.
•
Edit the values for Red, Green,
Blue, White, and Intensity values
(in percent%) by using the arrow
buttons.
Scratch Pad
Warm White*
Cool White*
Day Light*
•
Once the values are adjusted, the
"Save Preset" menu option
appears to save the edits.
Select Preset to Edit - (Option)
Selects a current preset and outputs
the preset, so preset can be edited.
NOTES:
*Only intensities may be stored on
White Colour Temperature presets.
RGBW in these presets cannot be
edited or changed.
Note: To save a specific look of the
fixture, see Save Presets.
**If a Calibrated Preset's Colour Mix is
changed (5 thru 25), an asterisk '*' is
appended to the end of the name to
indicate that it has been modified.
This only happens if the name
matches the original calibrated name,
stored in EEPROM. This does not
happen if the Intensity is changed,
only the colour mix.
Preset X (5 through 31)**
Note: When DMX512 signal is present, Edit a Preset option will not appear in menu structure.
Color Mix
Sub Menu
Options
Comments
Red
Users can:
Green
Blue
•
Edit Red, Green, Blue, White, and
Select Colour or Intensity to Adjust -
(Option)
Intensity values (in percent%) by
using the arrow buttons.
•
Once the values are adjusted,
press [OK] to save the edits.
White
Intensity
Note: When DMX512 signal is present, Color Mix option will not appear in menu structure.
Fan Control
Sub Menu
Options
Comments
Highlight "Max" button and hit [OK]
button on menu. Sets the maximum
speed of the fan.
Max
Select and Set Fan Speed - (Option)
Level sets the fan to a constant speed
(will not vary). Adjust level (on fan
speed level bar) using Left and Right
arrow buttons, highlight "Level" button
in menu, and hit [OK] on menu to use
user-defined level.
Note, hit Cancel to cancel any
changes you made.
Level
Continued next page
12
OPERATION AND PROGRAMMING
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
Menu Structure (continued)
Continued from previous page
Settings
Sub Menu
Options
Comments
SETTINGS - (Option)
Scrolls and sets the various fixture
settings using arrow buttons.
Lock Fixture
Sub Menu
Options
Comments
Use arrow buttons to make selection.
Press [OK] to accept. Note, a
password must be established (set) in
order to lock a fixture. Locking the
fixture will disable access to changing
menu settings.
LOCK - Are you sure?
Yes (to Lock Fixture) / No
Enter Password
Sub Menu
Options
Comments
For details, refer to "Security" on
Enter Pass PIN
Enter four-digit password
LED Status
Sub Menu
Options
Comments
Displays LED’s current status (in
percentage%) of Intensity, Red,
Green, Blue, and White elements of
the LED). Also displays current colour
temperature (i.e., WARM WHITE),
Fan Speed, operational LED junction
temperature, power settings.
LED Status Information
LED 1
Scrolls through the various levels
using arrow buttons as indicated on
menu screen. Depending on the
arrow button pressed, the screens
may appear in a different order that
shown in "Options".
Displays DMX levels for each LED
element (Red, Green, Blue, and
White) and total power.
Levels
3. Security
Unwanted changes to the Fixture's Configuration or Setting can be controlled by setting a security level, or Locking
the Fixture. Three levels of security are available in addition to completely Locking the Fixture.
PLCYC LED Luminaires are shipped with default passwords. Users may set their own password (four-digit number).
When setting a password, write it down and keep it in a secure location. Note, Philips Selecon does not have records
of passwords established by users or owners.
Note: Contact Philips Selecon technical support if a unit is locked and the password is lost for instructions on how to
reset luminaire.
Note: If the Fixture is locked when it is powered down the fixture will remain in the locked state when powered up.
Passwords
Establishing or Changing Passwords
Step 1. At a Status Screen, press [MENU] and scroll to "Settings", press [OK].
Step 2. Go to the Security section.
Security
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
Step 3. Select a Level to change ( Level 1 PIN / Level 2 PIN / Level 3 PIN).
Step 4. Press [OK] to edit using the [UP ARROW], [DOWN ARROW], [LEFT ARROW] or [RIGHT ARROW]
keys to enter a four-digit password (using 0 to 9).
Step 5. Press [OK] to save changes. If you hit [ESC] (Escape) password will not be stored and process must be
repeated.
Step 6. Password is set.
Note: The current security level is displayed next to the Security heading. Only Passwords at, or below, that level
will be displayed for modification. The level can be changed by entering a higher level Password on the "Enter
PassPIN line directly below the Security heading, like Step 4 above.
Security Levels
Security Level
Description
Default PassPIN
System is locked; the only key that is active is the Menu/ESC Key. When this key is pressed a
PassPIN is requested.
0
Not Applicable
All keys are Active.
You can select any Preset, and change Intensity, set DMX Address.
1
2
3
1111
2222
3333
Editing and Saving of Presets is added to Level 1 functionality.
Operationally the same as level 2, however all settings are available on the Settings screen.
Locking Fixture
To lock the fixture:
Step 1. At a Status Screen, press [MENU] and scroll to "Lock Fixture".
Step 2. Press [OK].
Step 3. Use [LEFT ARROW] or [RIGHT ARROW] keys to highlight "YES" ", press [OK].
Step 4. Fixture is now locked.
Note: When the Fixture is Locked only the [ESC]/[MENU] key is functional. Pressing this key will display a request
for a password. When a valid password is entered the fixture is unlocked to the security level of the entered password.
4. Presets
Presets are Colour Mixes that are stored in the Fixture, they can be recalled to reproduce a specific output from the
fixture. Presets are made up of a Colour Mix; Red, Green, Blue, and White. They also have Intensity associated with
them.
Presets can be recalled via the User interface or by a DMX channel, when under DMX control. The Preset’s Intensity
is applied if the User Interface is used; if DMX, the DMX Intensity channel is used for Intensity.
Presets Types
Presets are classified as Locked, Protected, or User. The type of preset determines what aspects of the Preset can be
modified.
Locked
Locked Presets are factory Calibrated, and their Colour Mix cannot be changed by the user. Their Intensity can be
changed. Three Presets (2-4), "Warm White', "Cool White", and "Day Light", are Locked.
Preset 0, the "off" preset is also Locked to the OFF value.
14
OPERATION AND PROGRAMMING
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
Protected
Protected Presets are also Factory Calibrated, and by default are Protected from changes to their Colour Mix. Their
Intensity can be changed. Protected Presets are Presets 5-25. They can be Un-Protected by setting "Protected" to
"No"; see section on Settings. If Un-Protected these presets function like User Presets.
The Factory Calibrated values for the protected presets can be re-loaded to the original factory calibration settings by
setting "Load Factory" to "Yes" "; see section on Settings.
User
User Presets can have their Colour Mix and Intensity changed without restriction.
Note: If the Colour Mix of a Factory Calibrated Preset is changed, by turning protection Off, an '*' is appended to the
end of the Preset's Name to indicate that the Calibrated values have been changed.
Editing Preset Names
On the Edit Preset screen, the option is available to edit the name of a preset, via Screen button. However, the names
of Presets 0-4 cannot be edited.
Use the [LEFT ARROW] and [RIGHT ARROW] keys to select the character to be changed and use the [UP
ARROW] and [DOWN ARROW] keys to change that character. The Character Scroll order is A-Z, space, 0-9. If you
are scrolling up the Alpha character displays as Upper Case; if you are scrolling down the Alpha character displays as
Lower Case. Stop on the character you want, ignoring case, then press the opposite [UP ARROW] or [DOWN
ARROW] key if you want to change the case. [OK] to save changes, [ESC] to cancel changes.
5. Settings
The following Parameters can be changed on the Settings Screen.
The first column "Security Level" is the minimum security level you have to be at before the line is displayed for
editing in the Settings screen.
To edit a value on the Setting Screen, use the [UP ARROW] or [DOWN ARROW] keys to move the highlight to the
settings value you wish to change. Press [OK] to begin editing that value. Use the [UP ARROW], [DOWN
ARROW], [LEFT ARROW] or [RIGHT ARROW] keys to make changes to the value. Press [OK] when complete to
save changes, or [ESC] to cancel changes to that value.
When done making changes on the Settings Screen press [ESC] to re-boot fixture and implement changes. Fixture
will not re-boot if nothing was changed.
Setting Options & Descriptions
Security Level
Parameter
Values
Default
Description
Security
There are 4 levels of security, this allows
you to change the level while in the
Settings Screen.
Enter
PassPIN
1
3
3
3
3
4-Digits (0 to 9)
4-Digits (0 to 9)
4-Digits (0 to 9)
4-Digits (0 to 9)
1 - 3 or Locked
****
1111
2222
3333
3
Level 1 PIN
Level 2 PIN
Level 3 PIN
Power-Up
Sets Level 1 PassPIN
Sets Level 2 PassPIN
Sets Level 3 PassPIN
Security Level after Power-Up, if not
Locked (Level 0)
Settings
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
General
30W, 40W, 50W, 70W,
90W, 100W, 100W
Sets the maximum power setting of the
LED engine.
1
Power Limit
Power-Up
100W
Cool White
No
When the Fixture Powers-Up what does it
output. Scratch Pad is an automatically
saved Preset. Last Set is the last thing
coming out of the fixture, this could be
Warm White with the intensity changed
from that of the Preset.
Off, Scratch Pad,
Warm White, Cool
White, Day Light,
Preset30, Preset31,
Last Set
1
3
Presets
3
Reset Hours
No, Yes
Resets luminaire’s operational hours.
Determines if the factory Calibrated
Presets' Colour Mix is protected from
changes.
Protected
No, 5 - 25
No, Yes
Yes
No
Reload Factory Calibrated Presets,
Intensity changes will also be reloaded.
3
Load Factory
DMX
Enables or disabled DMX communication
through the luminaires DMX512 ports.
Sets the DMX feature to Wireless DMX (if
wireless DMX option is installed - sold
separately).
No, Yes, or Wireless (if
equipped)
3
DMX Enabled
Yes
DMX512 address. Note, it can be set if
displayed.
1
2
Address
Map
001 to 512
001
Defines size/precision of DMX map.
Colour Mixing/Intensity in 16-bit provides
higher resolution for precision control. 3-
Chan provides minimal channel usage.
8-bit, 16-bit, or 3-Chan
16-bit
If DMX is detected and then goes away,
this defines what will happen to the output.
At end of 8Hr hold Fixture goes to Power-
Up setting.
Off, Hold, Hold 8hr (8
hours), or Power-Up
2
When no DMX
Hold
Fan
Normal - Normal Mode Provides higher
cooling margin for thermally challenging
applications. Recommended for full power
(RGBW @ 100%) applications with large
and numerous changes in power. Quiet -
(Quiet Mode) Quite Mode is similar to
Normal mode, but it controls fan tightly to
reduce fan noise.
3
3
Normal / Quiet
Normal or Quiet
Quiet
Max%
Min%
0 to 100%
0 to 100%
100
1
Sets the maximum fan speed
Sets the minimum fan speed
3
Display
3
Flip Display
No, Yes
No
Flips (inverts) Display and Keypad Arrows.
Note: To Exit the Settings screen, use the [ESC] key. [ESC] and [OK] can be used to cancel or save changes to an
individual parameter. However, once a parameter has been accepted, by pressing [OK] that change cannot be undone/
canceled by pressing the [ESC] key.
16
OPERATION AND PROGRAMMING
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
DMX CONTROL
This section contains information for operating the luminaire using DMX control in 16-Bit, 8-Bit, or 3-Channel (3-
Note: These tables assume a DMX start address of 1. When a different starting address is used, this address becomes
channel 1 function and other functions follow in sequence.
1. 16-Bit Mode
Table 3 provides DMX channel mapping of all DMX512 control values when the PLCYC LED Luminaire is in 16-bit
DMX512 mode (as set by the luminaire’s menu system).
Table 3: PLCYC LED Luminaire DMX Channel Mapping (16-Bit Mode)
Default - recom-
mended console
default values
DMX
Channel
Parameter
Range DMX
Range%
Description
1
2
3
4
5
6
7
8
9
Intensity - High
Intensity - Low
0 - 65535
0 - 65535
0 - 65535
0 - 65535
0 - 65535
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0
0
0
0
0
16-bit control for Intensity of LED settings.
16-bit control of Red LEDs from 0 to full.
16-bit control of Green LEDs from 0 to full.
16-bit control of Blue LEDs from 0 to full.
16-bit control of White LEDs from 0 to full.
Red - High Byte
Red - Low Byte
Green - High Byte
Green - Low Byte
Blue - High Byte
Blue - Low Byte
White - High Byte
White - Low Byte
10
11
12
Used to access presets stored in fixture firmware,
such as CCT presets, defined gel presets, etc.
No Preset Activated = DMX 0-3 (DEFAULT)
colour Preset 0 (Off) = DMX 4 - 7
Colour Preset 1 (Scratch Pad) = DMX 8 - 11
Colour Preset 2 (Warm White) = DMX 12 - 15
Colour Preset 3 (Cool White) = DMX 16 - 19
Colour Preset 4 (Daylight) = DMX 20 - 23
Colour Preset 5 (Arc White) = DMX 24 - 27
Colour Preset 6 (Red) = DMX 28 - 31
Colour Preset 7 (Yellow) = DMX 32 - 35
Colour Preset 8 (Daylight Blue) = DMX 36 - 39
Colour Preset 9 (Magenta) = DMX 40 - 43
Colour Preset 10 (Aqua) = DMX 44 - 47
Colour Preset 11 (Medium Amber) = DMX 48 - 51
Colour Preset 12 (Lavender) = DMX 52 - 55
Colour Preset 13 (Blue) = DMX 56 - 59
Colour Preset 14 (Light Pink) = DMX 60 - 63
Colour Preset 15 (Green) = DMX 64 -67
Colour Preset 16 (Pink) = DMX 68 - 71
Colour Preset 17 (Amber White) = DMX 72 - 75
Colour Preset 18 (Dark Fuchsia) = DMX 76 - 79
Colour Preset 19 (Light Amber) = DMX 80 - 83
Colour Preset 20 (Steel Blue) = DMX 84 - 87
Colour Preset 21 (Lt. Green/Blue) = DMX 88 - 91
Colour Preset 22 (Orange) = DMX 92 - 95
Colour Preset 23 (Medium Pink) = DMX 96 - 99
Colour Preset 24 (Cyan) = DMX 100 - 103
Colour Preset 25 (Purple) = DMX 104 - 107
Colour Preset 26 (Custom) = DMX 108 - 111
Colour Preset 27 (Custom) = DMX 112 - 115
Colour Preset 28 (Custom) = DMX 116 - 119
Colour Preset 29 (Custom) = DMX 100 - 123
Colour Preset 30 (Custom) = DMX 124 - 127
Colour Preset 31 (Custom) = DMX 128 - 131
Preset Colour
Selection
0 - 255
0 - 100%
0
Not used (for future use)
- Continued Next Page -
16-Bit Mode
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
Table 3: PLCYC LED Luminaire DMX Channel Mapping (16-Bit Mode)
Allows for luminaire timing of intensity. Profile
should default to DMX 255 for smoothest console
fade times. Refer to "PLCYC LED Luminaire DMX
Timing Channel Detail" on page 22 for more
information on timing values.
13
14
Intensity Time
Colour Time
0 - 255
0 - 255
0 - 100%
0 - 100%
255
255
Allows for luminaire timing of LEDs. Profile
should default to DMX 255 for smoothest console
fade times.Refer to "PLCYC LED Luminaire DMX
Timing Channel Detail" on page 22 for more
information on timing values.
Used to set different modes, parameters, and
functions of the luminaire. Set control channel
value for desired action. Hold value for at least 3
seconds. Set control channel value to 0 without
any scaling.
Default Setting on Console = DMX 0
Display On/Off = DMX 3 - 4
Reset All to Defaults = DMX 5 - 7
Quiet Mode = DMX 11 - 13
Normal Mode = DMX 14 - 15
Preset 1 Store = DMX 20 - 21
Preset 2 Store (Intensity Only) = DMX 22 - 23
Preset 3 Store (Intensity Only) = DMX 24 - 25
Preset 4 Store (Intensity Only) = DMX 26 - 27
Preset 5 Store = DMX 28 - 29
Preset 6 Store = DMX 30 - 31
Preset 7 Store = DMX 32 - 33
Preset 8 Store = DMX 34 - 35
Preset 9 Store = DMX 36 - 37
Preset 10 Store = DMX 38 - 39
Preset 11 Store = DMX 40 - 41
Preset 12 Store = DMX 42 - 43
Preset 13 Store = DMX 44 - 45
Preset 14 Store = DMX 46 - 47
Preset 15 Store = DMX 48 - 49
Preset 16 Store = DMX 50 - 51
Preset 17 Store = DMX 52 - 53
Preset 18 Store = DMX 54 - 55
Preset 19 Store = DMX 56 - 57
Preset 20 Store = DMX 58 - 59
Preset 21 Store = DMX 60 - 61
Preset 22 Store = DMX 62 - 63
Preset 23 Store = DMX 64 - 65
Preset 24 Store = DMX 66 - 67
Preset 25 Store = DMX 68 - 69
Preset 26 Store = DMX 70 - 71
Preset 27 Store = DMX 72 - 73
Preset 28 Store = DMX 74 - 75
Preset 29 Store = DMX 76 - 77
Preset 30 Store = DMX 78 - 79
Preset 31 Store = DMX 80 - 81
Fixture Reset* = DMX 250 - 255
15
Control
0 - 255
0 - 100%
0
18
DMX CONTROL
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
2. 8-Bit Mode
Table 2-1 provides DMX channel mapping of all DMX512 control values when the PLCYC LED Luminaire is in 8-
bit DMX512 mode (as set by the luminaire’s menu system).
Table 2-1: PLCYC LED Luminaire DMX Channel Mapping (8-Bit Mode)
Default -
DMX
Channel
recommended
console default
values
Parameter
Range DMX
Range%
Description
1
2
3
4
5
Intensity
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0
0
0
0
0
8-bit control for Intensity of LED settings.
8-bit control of Red LEDs from 0 to full.
8-bit control of Green LEDs from 0 to full.
8-bit control of Blue LEDs from 0 to full.
8-bit control of White LEDs from 0 to full.
Red
Green
Blue
White
Used to access presets stored in fixture firmware,
such as CCT presets, defined gel presets, etc.
No Preset Activated = DMX 0-3
Colour Preset 0 (Off) = DMX 4 - 7
Colour Preset 1 (Scratch Pad) = DMX 8 - 11
Colour Preset 2 (Warm White) = DMX 12 - 15
Colour Preset 3 (Cool White) = DMX 16 - 19
Colour Preset 4 (Daylight) = DMX 20 - 23
Colour Preset 5 (Arc White) = DMX 24 - 27
Colour Preset 6 (Red) = DMX 28 - 31
Colour Preset 7 (Yellow) = DMX 32 - 35
Colour Preset 8 (Daylight Blue) = DMX 36 - 39
Colour Preset 9 (Magenta) = DMX 40 - 43
Colour Preset 10 (Aqua) = DMX 44 - 47
Colour Preset 11 (Medium Amber) = DMX 48 - 51
Colour Preset 12 (Lavender) = DMX 52 - 55
Colour Preset 13 (Blue) = DMX 56 - 59
Colour Preset 14 (Light Pink) = DMX 60 - 63
Colour Preset 15 (Green) = DMX 64 -67
Colour Preset 16 (Pink) = DMX 68 - 71
Preset Colour
Selection
6
0 - 255
0 - 100%
0
Colour Preset 17 (Amber White) = DMX 72 - 75
Colour Preset 18 (Dark Fuchsia) = DMX 76 - 79
Colour Preset 19 (Light Amber) = DMX 80 - 83
Colour Preset 20 (Steel Blue) = DMX 84 - 87
Colour Preset 21 (Lt. Green/Blue) = DMX 88 - 91
Colour Preset 22 (Orange) = DMX 92 - 95
Colour Preset 23 (Medium Pink) = DMX 96 - 99
Colour Preset 24 (Cyan) = DMX 100 - 103
Colour Preset 25 (Purple) = DMX 104 - 107
Colour Preset 26 (Custom) = DMX 108 - 111
Colour Preset 27 (Custom) = DMX 112 - 115
Colour Preset 28 (Custom) = DMX 116 - 119
Colour Preset 29 (Custom) = DMX 100 - 123
Colour Preset 30 (Custom) = DMX 124 - 127
Colour Preset 31 (Custom) = DMX 128 - 131
7
8
Not used (for future use)
Allows for timing control of both the intensity and
Colour parameters. Channel should default to 255
for smoothest actions using console and/or manual
fades. Refer to "PLCYC LED Luminaire DMX
Timing Channel Detail" on page 22 for more
information.
Timing
0 - 255
0 - 100%
255
- Continued Next Page -
8-Bit Mode
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
Table 2-1: PLCYC LED Luminaire DMX Channel Mapping (8-Bit Mode)
Used to set different modes, parameters, and
functions of the luminaire. Set control channel
value for desired action. Hold value for at least 3
seconds. Set control channel value to 0 without
any scaling.
Default Setting on Console = DMX 0
Display On/Off = DMX 3 - 4
Reset All to Defaults = DMX 5 - 7
Quiet Mode = DMX 11 - 13
Normal Mode = DMX 14 - 15
Preset 1 Store = DMX 20 - 21
Preset 2 Store (Intensity Only) = DMX 22 - 23
Preset 3 Store (Intensity Only) = DMX 24 - 25
Preset 4 Store (Intensity Only) = DMX 26 - 27
Preset 5 Store = DMX 28 - 29
Preset 6 Store = DMX 30 - 31
Preset 7 Store = DMX 32 - 33
Preset 8 Store = DMX 34 - 35
Preset 9 Store = DMX 36 - 37
Preset 10 Store = DMX 38 - 39
Preset 11 Store = DMX 40 - 41
Preset 12 Store = DMX 42 - 43
Preset 13 Store = DMX 44 - 45
Preset 14 Store = DMX 46 - 47
Preset 15 Store = DMX 48 - 49
Preset 16 Store = DMX 50 - 51
Preset 17 Store = DMX 52 - 53
Preset 18 Store = DMX 54 - 55
Preset 19 Store = DMX 56 - 57
Preset 20 Store = DMX 58 - 59
Preset 21 Store = DMX 60 - 61
Preset 22 Store = DMX 62 - 63
Preset 23 Store = DMX 64 - 65
Preset 24 Store = DMX 66 - 67
Preset 25 Store = DMX 68 - 69
Preset 26 Store = DMX 70 - 71
Preset 27 Store = DMX 72 - 73
Preset 28 Store = DMX 74 - 75
Preset 29 Store = DMX 76 - 77
Preset 30 Store = DMX 78 - 79
Preset 31 Store = DMX 80 - 81
Fixture Reset* = DMX 250 - 255
9
Control
0 - 255
0 - 100%
0
20
DMX CONTROL
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
3. DMX 3-Channel (3-Chan) Mode
Table 2-2 provides DMX channel mapping of all DMX512 control values when the PLCYC LED Luminaire is in 3-
Channel (3-Chan) DMX512 mode (as set by the luminaire’s menu system).
Table 2-2: PLCYC LED Luminaire DMX Channel Mapping (3-Chan Mode)
Default -
DMX
Channel
recommended
console default
values
Parameter
Range DMX
Range%
Description
1
Intensity
0 - 255
0 - 100%
0
8-bit control for Intensity of LED settings.
Used to access presets stored in fixture firmware,
such as CCT presets, defined gel presets, and
more.
No Preset Activated = DMX 0 - 3
Colour Preset 0 (Off) = DMX 4 - 7
Colour Preset 1 (Scratch Pad) = DMX 8 - 11
Colour Preset 2 (Warm White) = DMX 12 - 15
Colour Preset 3 (Cool White) = DMX 16 - 19
Colour Preset 4 (Daylight) = DMX 20 - 23
Colour Preset 5 (Arc White) = DMX 24 - 27
Colour Preset 6 (Red) = DMX 28 - 31
Preset Colour
Selection
Notes:
Colour Preset 7 (Yellow) = DMX 32 - 35
Colour Preset 8 (Daylight Blue) = DMX 36 - 39
Colour Preset 9 (Magenta) = DMX 40 - 43
Colour Preset 10 (Kelly Green) = DMX 44 - 47
Colour Preset 11 (Medium Amber) = DMX 48 - 51
Colour Preset 12 (Lavender) = DMX 52 - 55
Colour Preset 13 (Blue) = DMX 56 - 59
Colour Preset 14 (Light Pink) = DMX 60 - 63
Colour Preset 15 (Green) = DMX 64 - 67
Colour Preset 16 (Pink) = DMX 68 - 71
Colour Preset 17 (Amber White) = DMX 72 - 75
Colour Preset 18 (Dark Fuchsia) = DMX 76 - 79
Colour Preset 19 (Light Amber) = DMX 80 - 83
Colour Preset 20 (Steel Blue) = DMX 84 - 87
Colour Preset 21 (Lt. Green/Blue) = DMX 88 - 91
Colour Preset 22 (Orange) = DMX 92 - 95
Colour Preset 23 (Medium Pink) = DMX 96 - 99
Colour Preset 24 (Cyan) = DMX 100 - 103
Colour Preset 25 (Purple) = DMX 104 - 107
Colour Preset 26 (Custom) = DMX 108 - 111
Colour Preset 27 (Custom) = DMX 112 -115
Colour Preset 28 (Custom) = DMX 116 - 119
Colour Preset 29 (Custom) = DMX 100 - 123
Colour Preset 30 (Custom) = DMX 124 - 127
Colour Preset 31 (Custom) = DMX 128 - 131
•
Colour Presets 5
through 25 are set
factory Colours and
can be reloaded if
needed through the
fixture’s menu sys-
tem.
2
0 - 255
0 - 100%
0
•
These Colours
have been matched
to precise X and Y
coordinates at the
center of the beam
at wide angle, we
have given you the
ability to adjust
these Colours as
your personal per-
ception may vary.
Allows for timing control of both the intensity and
Colour parameters. Channel should default to 255
for smoothest actions using console and/or
manual fades. Refer to "PLCYC LED Luminaire
information.
3
Timing
0 - 255
0 - 100%
255
DMX 3-Channel (3-Chan) Mode
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
4. Lighting Console Settings for Preset White
16-Bit Mode
Below are the DMX512 console values and levels* for Warm White, Cool White, and Day Light presets in 16-bit
mode.
Red Channel
Green Channel
Blue Channel
DMX
White Channel
White Preset
DMX
DMX
DMX
DMX%
DMX%
Value
DMX%
DMX%
Value
Value
Value
Warm White
Cool White
Day Light
65535
100
100
100
36700
41287
53739
56
63
82
0
0
47185
61603
58982
72
94
90
65535
65535
8520
13
40
26214
8-Bit Mode
Below are the DMX512 console values and levels* for Warm White, Cool White, and Day Light presets in 8-bit
mode.
Red Channel
Green Channel
Blue Channel
DMX
White Channel
White Preset
DMX
DMX
DMX
DMX%
DMX%
Value
DMX%
DMX%
Value
Value
Value
Warm White (3200K)
Cool White (4000K)
Day Light (5600K)
255
100
100
100
163
194
237
64
76
93
0
0
217
255
255
85
255
255
46
18
51
100
100
130
Note: *Values and levels shown for Preset White (in both 16 and 8-bit modes) are approximate. Due to the
characteristics of LED technology, actual values may vary slightly between fixtures.
5. PLCYC LED Luminaire DMX Timing Channel Detail
Timing channel control improves the timed moves of certain groups of parameters. The PLCYC LED Luminaire
provides two timing channels in 16-bit mode (one for intensity time and one for colour time) and one timing channel
in 8-bit (colour and intensity timing combined). The luminaire uses its timing channel value to calculate a smooth
continuous operation for a given time and transition.
Guidelines:
• Timing channels support time values from zero to 169 seconds.
• To use a timing channel instead of console timing, it is recommended to set the timing channel to the desired value
and set cue and/or console cue fade time to zero. A combination of time controls can produce unexpected results.
• The default value setting in the profile should be 255 (proportional control) to allow smooth operation when using
console timing.
• The timing channel data should change as a snap. A zero value will give the fastest operation, however, without
any smoothing this can appear "steppy" in console timed moves.
22
DMX CONTROL
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
Table 3: PLCYC LED Luminaire Timing Channel Detail
% Value
DMX
= Seconds
0
0 (Full Speed)
0.2
0.4
0.6
0.8
1
1
2
1
2
3
4
5
6
1.2
1.4
1.6
1.8
2
7
3
4
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
2.2
2.4
2.6
2.8
3
5
6
3.2
3.4
3.6
3.8
4
7
8
4.2
4.4
4.6
4.8
5
9
10
5.2
5.4
5.6
5.8
6
11
12
13
6.2
6.4
6.6
6.8
7.0
7.2
7.4
7.6
7.8
8
14
15
16
17
8.2
8.4
8.6
8.8
9
18
19
9.2
9.4
9.6
9.8
10
20
10.2
PLCYC LED Luminaire DMX Timing Channel Detail
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
% Value
DMX
= Seconds
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
10.4
10.6
10.8
11
21
22
11.2
11.4
11.6
11.8
12
23
24
12.2
12.4
12.6
12.8
13
25
26
13.2
13.4
13.6
13.8
14
27
28
14.2
14.4
14.6
14.8
15
29
30
15.2
15.4
15.6
15.8
16
31
16.2
16.4
16.6
16.8
17
32
33
17.2
17.4
17.6
17.8
18
34
35
18.2
18.4
18.6
18.8
19
36
37
19.2
19.4
19.6
19.8
20
38
39
21
40
41
22
23
24
25
24
DMX CONTROL
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
% Value
DMX
= Seconds
106
107
108
109
110
111
112
113
114
115
116
117
118
119
100
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
PLCYC LED Luminaire DMX Timing Channel Detail
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
% Value
DMX
= Seconds
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
80
81
63
64
82
83
84
85
65
66
86
87
88
89
90
67
68
91
92
93
94
95
69
96
97
98
70
71
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
100
121
122
123
124
125
126
127
128
129
130
131
132
133
72
73
74
75
76
77
78
79
80
81
82
83
26
DMX CONTROL
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
% Value
DMX
= Seconds
84
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250*
251*
252*
253*
254*
134
135
136
85
86
137
138
139
140
141
87
88
142
143
144
145
146
89
147
148
149
90
91
150
151
152
153
154
92
93
155
156
157
158
159
94
95
160
161
162
163
164
96
97
165
166
167
168
169
98
99
60mS
80mS
100mS
100mS
140mS
255*
(default)
100
160mS
Note: * DMX values 250 to 255 provide smoothing when using console fade timing. DMX value 255 (recommended
default) will provide the smoothest timing.
PLCYC LED Luminaire DMX Timing Channel Detail
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
CLEANING AND CARE
WARNING! All cleaning should be performed with power completely removed from the luminaire. Never remove
protective covers when luminaire is powered. Wear appropriate protective eye wear and gloves when cleaning the
fixture. All service and maintenance, other than described herein, should be performed by a qualified technician or
Authorized Service Center.
1. Special Cleaning and Care Instructions
Being a solid-state fixture, and unlike most fixtures, the PLCYC LED Luminaire requires very little routine
maintenance by the user. This section covers portions of the luminaire that can be removed for cleaning.
The PLCYC LED Luminaire special care when it comes to cleaning front lens assembly. Additional care needs to be
taken with the plastic components because they are much easier to scratch or damage than glass.
The following is a list of cleaning materials required to care for your PLCYC LED Luminaire:
• Lint free lens tissue
• Lint or powder free gloves
• Reagent grade isopropyl alcohol*
• A mild soap solution.
Note: *Reagent grade isopropyl alcohol is good to use on the PLCYC LED Luminaire plastic optics with anti-
reflection coatings.
If the lens is still dirty after using isopropyl alcohol, for instance if fingerprints or oil is just redistributed and not
cleaned off the optic, then a mild soap and water solution can be used to gently wash the lens. Repeat the cleaning
with isopropyl alcohol to eliminate streaks and soap residue.
WARNING! Under no circumstances should ammonia-based cleaners, acetone, or other harsh solvents be used on or
near the PLCYC LED Luminaire. These types of cleaners or solvents can permanently damage the optics or housings
of the fixture.
If you have any questions regarding the use or care of your PLCYC LED Luminaire, please contact Philips Selecon
technical support or your local Authorized Dealer.
2. Front Lens / Reflector Cleaning
To clean the front lens and reflector:
Step 1. Turn off luminaire and allow to cool completely.
Step 2. Apply a small amount of reagent grade isopropyl alcohol to lint-free lens tissue.
Step 3. Wipe all debris, dirt, fingerprints, etc. from lens and reflector.
Step 4. Using a second lint-free lens tissue, wipe off any alcohol residue.
3. Service and Maintenance
For all other service and maintenance issues, please contact your local Philips Selecon office or an Authorized
Service Center.
28
CLEANING AND CARE
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
WARNING! Disassembly (other than as described herein), alterations, unauthorized service, etc. will void the
product warranty. Contact your local Philips Selecon office or an Authorized Service Center for technical support and
service.
4. Accessories
Only Philips Selecon approved accessories should be used with your PLCYC LED Luminaire. For a list of available
accessories from Philips Selecon, please see "Accessories" on page 3. For questions regarding accessories, please
contact your local Authorized Philips Selecon Dealer or Philips Selecon office.
Accessories
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
TROUBLESHOOTING
1. Troubleshooting Guide
The chart below provides possible causes and remedies for various error messages and/or symptoms.
WARNING! Any service and maintenance (including troubleshooting), other than described herein should be
performed by an Authorized Philips Selecon Dealer or Service Center.
Description
Symptom
Possible Cause/Remedy
Unit is set to Preset Off...
Fixture will not produce or
output light
Make sure unit is set to proper Preset.
DMX command to 0 intensity...
Adjust intensity to higher level.
No light output.
Circuit not energized...
verify circuit breaker is turned on.
Not plugged in...
No power at luminaire.
Luminaire does not power up
ensure A/C cable is connected to power source.
Power cable wired incorrectly...
verify power cable and connector are wired correctly.
Not detecting DMX data...
Disconnect and reconnect DMX input cable.
Unit is not set to be controlled by DMX - check menu settings.
Check all DMX connections (at control source and luminaire).
DMX data cable not wired correctly or has a broken conductor...
check DMX data cable for proper wiring.
Fixture will not respond to DMX
commands.
DMX Data Control.
information.
Luminaire has detected an over temperature condition...
The luminaire will reduce power to its LED if it senses that the LED
is operating over the specified temperature. LED temperature is
read and recorded through a thermistor imbedded in the LED chip.
Fan is not operating. Listen for fan operation or adjust settings to
increase fan speed. On luminaires with a display check system
status menu for status of fans and LED operation.
Fixture appears not to be
operating at full brightness.
LED (light) is getting dimmer.
Local programming.
Password protection is on (locked)...
Input proper password to allow local programming and/or
adjustments.
Unit will not allow local
programming or changes.
Unit is controlled by DMX...
Disconnect input cables to check issue.
30
TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
TECHNICAL SPECIFICATIONS
1. PLCYC LED Luminaire Operational Specifications
Source:
True RGBW 120 Watt LED chip
Light Output:
Colour Temperature:
Input Voltage:
Current:
> 2,000 lumens
3000 - 5600K (user adjustable)
100V to 240V (+/- 10%, auto-ranging)
1.25 Amps (120V) / 0.63 Amps (240V)
50/60Hz
Frequency:
Ambient Temperature:
Humidity:
0 to 40 degrees C (32 to 104 degrees F)
5%-95% Non condensing
Forced-Air
Cooling:
Weight:
7.3 lbs (3.3 kg) - Luminaire only (no mount, AC input cable or accessories)
CE Marked (International models) and ETL / cETL Listed (North America models)
Compliance:
Note: Common model specifications shown. For specific model specifications, features, and accessories, refer to the
product specification sheet or visit the Philips Selecon web site at www.seleconlight.com for more details.
2. PLCYC LED Luminaire Dimensions
Side View
Front View
277.4 mm
10.9 in
238.8 mm
9.4 in
170.5 mm
6.7 in
240.8 mm
9.5 in
313.1 mm
12.3 in
191.0 mm
7.5 in
C
PLCYC LED Luminaire Operational Specifications
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & User’s Manual
PLCYC LED Luminaires
Notes
32
TECHNICAL SPECIFICATIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
PLCYC LED Luminaires
Installation & User’s Manual
Notes
PLCYC LED Luminaire Dimensions
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|