Philips Flat Panel Television FTR9952 19S User Manual

MAINS INLET

AUDIO IN

AUDIO OUT

VGA IN

VGA OUT

CABLE

EXTERNAL 1

EXTERNAL 2

EXTERNAL 3

OUT

VGA MONITOR

AUDIO

MAINS INLET

OUT

AUDIO MONITOR

NO FUNCTION

SURROUND SOUND CENTER IN

AUDIO MONITOR

OUT

VGA MONITOR

ANTENNA

Download from Www.Somanuals.com. All Manuals Search And Download.

Your rem ote control

VCR 1

VCR 2

DVD

TUNER

TAPE

SAT

selection of EXT1, EXT2, EXT3, FRO NT,

VGA or TV channels p. 10

AMP

peripheral selection with

remote control

switch to standby p. 10

select your choice p. 5

TV TV selection

dual screen on/off p. 17

O K activate your choice

volume up/down p. 10

sound mute p. 10

programme selection p. 10

picture format p. 10

bilingual choice/sound mode selection p. 10

continuous subtitles p. 11

subtitle language selection p. 25

(DVD - Digital Video Disc)

teletext on/off p. 18

on screen info p. 10

previous programme p. 10

Teletext p. 18

direct txt page or subject selection

index page selection

interrupt teletext display

mix tv/txt picture

‡

†

Video recorder p. 25

Digital Video Disc p. 25

enlarge

DVD SELECT

DVD

reveal hidden information

time display p. 12

subpage selection p. 19

AUDIO

T-C

P^-

ﬁ

Dual screen p. 17

ﬁ

freeze the main picture p. 12

reduce image noise

-P+ channel selection

switching screens

multi screen on/off

freeze the subpicture

sound personal preference

Installation p. 5

yÚ

centre mode on/off p. 11

PICTURE, SO UND, FEATURES menus p. 11

program m e list p. 11

VGA menu p. 24

direct txt page or subject selection p. 18

PICTURE

SOUND

Sm art Controls p. 11

picture and sound settings

Preparation

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparation

& Place the receiver box wherever you want, but leave at least 5 cm space free

all around the box for ventilation and do not cover the ventilation openings,

(e.g. on the ground, in a cupboard, behind a wall, in another room....).

To prevent any unsafe situations, do not place any objects on top of the

monitor or the receiver. No naked flame sources, such as lighted candles,

shoud be placed on or in the vicinity.Avoid heat, direct sunlight and exposure

to rain or water.The equipment shall not be exposed to dripping or splashing

and no objects filled with liquids, such as vases, shall be placed on it.

é Connect the supplied aerial cable 1 and the VGA cable with trailing audio

cinch connectors 2 as shown in the inside frontcover of this handbook.

Make sure all screws of the cable 2 are tightened well.

“ To connect your computer, see p. 22.

To connect other peripherals, see p. 20.

In order to obtain the best result, please use only the supplied antenna cables

between the receiver box and videorecorder, and between videorecorder and

antenna connector.

‘ Insert the mains cord supplied 3 (with filter) into the MAINS INLET at the

back of the monitor and the mains cord 4 at the back of the receiver. Put

both in the wall sockets.

VCR 1

VCR 2

DVD

TUNER

TAPE

SAT

Please, only use the m ains cord 3 (with filter) supplied with the

m onitor, for the m onitor and the m ains cord 4 supplied with the

receiver, only for the receiver.

AMP

ZOOM

( Remote control: Remove the cover of the battery compartment.

Insert the 2 batteries supplied (Type R03G-1.5V).

Press the TV key next to the display to be sure your remote control is in the

TV mode.

RO 3 / AAA

The batteries supplied do not contain the heavy metals mercury and cadmium.

Nevertheless in many countries batteries may not be disposed of with your

household waste. Please check on how to dispose of batteries according to local

regulations.

§ Switch the TV on : Press the power button A at the right side of the

monitor and the one on the front of the receiver box.

A green indicator lights up and the screen comes on.

If the indicator is red, press the P + key on the remote control.

The green indicator blinks every time you press a key on the remote control.

When you switch on your set for the first time, the menu LANGUAGE

automatically appears on the screen.The explanation appears in different languages

one at a time.

Preparation

Download from Www.Somanuals.com. All Manuals Search And Download.

With the sim plified rem ote control supplied with the monitor you can:

•

switch menu on or off with the MENU key

select a menu or menu item with the cursor keys

activate the selection you made with the O K key

switch your flat colour television to standby or on again with the B key

mute the sound with the ¬ key

select predefined picture and sound settings with the SMART CO NTRO LS

PICTURE and SO UND keys

(not with a monitor in a stand alone situation)

select the desired programme number with the - CH/P +

(not with a monitor in a stand alone situation)

adjust the volume with the - V + keys

VGA

FRONT

AV1

•

AV2

•

AV3

select one of the connected externals.

AV4

PICTURE SOUND

SMART

CONTROLS

CH/P

Preparation

Download from Www.Somanuals.com. All Manuals Search And Download.

PICTURE

SMART

SOUND

Installation

TXT

‡

†

INSTALLATIO N

Select the

m enu

P^-

ﬁ

yÚ

& Open the door of the remote control.

é Press S and s at the same time.

To use the m enus

& Use the cursor in the up/down, left/right directions to select a menu item.

é Press the O K key to activate.

VCR 1

VCR 2

DVD

TUNER

TAPE

SAT

“ Press one of the colour menu keys on the door of the remote control to

return or to switch menu off.

AMP

activate

select

I NSTALLATI ON

Me nu La ngua ge

Count r y

Aut oma t i c I ns t a l l a t i on

Ma nua l I ns t a l l a t i on

Gi ve Na me

I NSTALLATI ON

Me nu La ngua ge

Count r y

Aut oma t i c I ns t a l l a t i on

Ma nua l I ns t a l l a t i on

Gi ve Na me

adjustments

Re s huf f l e

Fa vour i t e Pr ogr a mme s

De c ode r / De s c r a mbl e r

Se t up

Fa vour i t e Pr ogr a mme s

De c ode r / De s c r a mbl e r

Se t up

programme list

features menu

sound menu

picture menu

Store TV channels

Select the m enu language and country

First, select your language and country.

& Select Menu Language in the INSTALLATIO N menu and press the O K key.

é Use the cursor left/right to select your language and press the O K key.

“ Select Country and press the O K key.

Me nu La ngua ge

Count r y

Aut oma t i c I ns t a l l a t i on

Ma nua l I ns t a l l a t i on

I NSTALLATI ON

‘ Select the country where you are now located and press the O K key.

Engl i s h

• • •

. . .

• • •

. . .

• • •

Select O ther when none of the countries applies.

LANGUAGE

Remark: If the language displayed on screen does not correspond with a language

you recognise or you want, act as follows:

& Press one of the colour menu keys on the door of the remote control to switch menu

• • •

COUNTRY

off.

• • •

é Press S and s at the same time.

Ot he r

Now the INSTALLATION menu is displayed, but is still in the language you do not

recognise or you do not want.

“ Press the cursor right.

‘ Now you can select your language with the cursor left/right.

You can now search for and store the TV channels in two different ways:

using autom atic installation or m anual installation (tuning-in channel by

channel).

Select your choice and press the O K key.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Autom atic installation

& In the Automatic installation menu select O n with the cursor left/right and

press the O K key to activate the searching. All TV channels are searched for

and stored automatically.

AUTOMATI C

Aut oma t i c I ns t a l l a t i on

I NSTALLATI ON

Wait until the message Ready is displayed at the bottom of the screen.

Se a r c hi ng

O%. . . . . . . . . . . . . . . . . . . . . 100%

If a cable system or a TV channel which broadcasts ACI (Automatic Channel

Installation) or a TV channel transmitting a teletext page with the frequencies

and programme names of all the TV channels which can be received, is

detected, the search is stopped and the programme list appears.

The programme list is automatically filled with all the programme numbers

and names of the TV channels transmitted.

10 . . .

11 . . .

12 . . .

13 . . .

BBC1

BBC2

I TV

. . .

. .

. . .

It is possible that the cable company or the TV channel displays a broadcast

selection menu. Layout and items are defined by the cable company or the TV channel.

Make your choice with the cursor and press the O K key.

AUTOMATI C

Aut omat i c I ns t al l at i on

Of f

I NSTALLATI ON

é Press one of the colour menu keys on the door of the remote control to

return to the INSTALLATIO N menu.

Manual installation

Searching for and storing TV channels is done channel by channel.

You must go through every step of the Manual Installation menu.

Selection Mode is only present and lights up if the country selected also

offers the channel option (C-channels for aerial channels, S-channels for cable

channels).

. . .

You can choose either channel or frequency mode.

& Select the TV system

( Sel ect i on Mode)

Sys t em

Sear ch

Pr ogr amme No

St or e

MANUAL

Select the country or part of the world from where you want to receive the

TV channel.

I NSTALLATI ON

If you are connected to a cable system, select your country or part of the

world where you are now located.

é Search for a TV channel

The frequency or the channel number increases until a TV channel is found.

In case of poor reception, you can improve the reception by adjusting the

frequency with the - P + keys.

Direct selection of a TV channel

If you know the frequency, the C- or S-channel number, enter the 3 digits of

the frequency directly with the digit keys 0 to 9 (e.g. 048).

“ Enter the programme number.

‘ To store your TV channel, select Store and press the O K key.

Repeat steps & to ‘ to store another TV channel.

( To exit from the menu press one of the colour menu keys on the remote

control.

After the new or extra TV channel has been stored, the TV automatically transfers the TV channel(s) to the video recorder provided with the

EasyLink function.The message: EasyLink : Downloading Presets ... appears at the bottom of the screen.

The programme list of the video recorder is now equal to the one of the TV.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Give nam e

It is possible to change the name stored in the memory or to assign a name

Me nu La ngua ge

Count r y

Aut oma t i c I ns t a l l a t i on

Ma nua l I ns t a l l a t i on

Gi ve Na me

to a TV channel for which a name has not yet been entered.A name with up

to 5 letters or numbers can be given to the programme numbers 0 to 99. For

example SUPER, BBC1,...

Between 99 and 0, in the column in the middle, you can also name any

peripherals that are connected to a euroconnector.

I NSTALLATI ON

Re s huf f l e

Fa vour i t e Pr ogr a mme s

De c ode r / De s c r a mbl e r

Se t up

& Select Give Nam e in the INSTALLATIO N menu and press the O K key.

é Select the programme number.

“ Press the O K key.

EXT1

EXT2

EXT3

FRONT

GI VE NAME

BBC1

BBC2

. . . .

‘ Select the character with the cursor up/down.

( Select the following position with the cursor right.

§ Select the following character.

è Press the O K key when finished.

! Press one of the colour menu keys to return to the INSTALLATIO N menu.

. . . . . . .

Spaces, numbers, language dependent characters and so on are located

between Z and A.

Reshuffle the program m e list

According to your preference you can change the order of the stored TV

channels.

& Select Reshuffle in the INSTALLATIO N menu and press the O K key.

é Select the programme number you want to change.

Use the cursor left/right to select another column of the programme list.

“ Press the O K key.

10 . . .

11 . . .

12 . . .

13 . . .

14 . . .

15 . . .

. . . . . .

RESHUFFLE

BBC1

BBC2

. . . .

. . . . . .

‘ Select the new number you want to exchange it with.

( Press the O K key.

Repeat the operation until all TV channels are allocated as you like.

§ Press one of the colour menu keys to return to the INSTALLATIO N menu.

Select Favourite TV channels

After leaving the installation you can browse through the TV channels and

externals by pressing the - P + key. Only those TV channels and externals

which are in the favourite list will be displayed. Non-favourite TV channels and

externals can still be selected with the digit keys.

You can also do this for a programme number reserved for the programmes

you receive from your decoder.

& Select Favourite Program m es in the INSTALLATIO N menu and press

the O K key.

EXT1

EXT2

EXT3

FRONT

. . .

10 . . .

11 . . .

12 . . .

13 . . .

14 . . .

15 . . .

. . . . . .

é Select your programme number.

“ Select Favourite with the cursor up/down.

‘ Select Yes or No with the cursor left/right.

. . . . .

FAVOURI TE

PROGRAMMES

Pr ogr a mme Numbe r

Fa vour i t e

( Repeat é to ‘ for every TV channel or extenral you want to make a

favourite or a

non-favourite TV channel or external.

§ Press one of the colour menu keys to return to the INSTALLATIO N menu.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Define Decoder/Descram bler program m e num bers

If a decoder or a descrambler is connected, see p. 20, you can define one or

more programme numbers as decoder programme numbers.

& Select Decoder/Descram bler in the INSTALLATIO N menu and press the

Pr ogr a mme

De c ode r St a t us

O K key.

DECODER/

DESCRAMBLER

é Select the programme number with the cursor up/down. Select the

programme number under which you have stored the programme coming

from your decoder with the digit keys

“ Select Decoder Status with the cursor up/down.

• Press the cursor left/right to select the input used to connect your decoder:

TV, EXT1 or EXT2.

• Select TV if you do not want the selected programme number being

activated as a decoder programme number.

‘ Use the red menu key to return or switch menu off.

If the TV is connected to a video recorder with the EasyLink function, the message

EasyLink: Downloading Presets.... appears at the bottom of the screen.

The programme list of the video recorder is equal again to the one of the TV.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Install TV Setup

Me nu La ngua ge

Count r y

I NSTALLATI ON

The Setup menu allows you to adjust initial settings, i.e. those which are not

related to the installation of the TV channels.

The Setup menu contains items that control the settings of the TV’s functions,

features, services and peripherals you may have connected.

Aut oma t i c I ns t a l l a t i on

Ma nua l I ns t a l l a t i on

Gi ve Na me

Re s huf f l e

Fa vour i t e Pr ogr a mme s

De c ode r / De s c r a mbl e r

Se t up

& Select Setup in the INSTALLATIO N menu and press the O K key.

é Use the red menu key to return or switch menu off.

Ext2 O utput

Ext 2 Out put

SETUP

See Record with your video recorder without EasyLink, p. 26.

I nf or ma t i on Li ne

Pi c t ur e Mut e

Aut o For ma t

Ce nt r e Mode

Inform ation Line

Press the cursor left/right to select O n.

After the selection of a TV programme or after pressing the i key on the

remote control, a TV channel which broadcasts teletext may transmit the

name of the TV channel or the programme name or another message which

appears briefly in the information line at the bottom of the screen.

When selected O ff, the information line will only appear after pressing the

i key, and not after the selection of a TV channel.

Picture Mute

Press the cursor left/right to select a Blue or Black screen when there is no

picture or information. In VGA mode always black mute is used.

Auto Form at

When Yes is selected with the cursor left/right,Auto format is part of the

picture formats that are selectable with the q key.

With the picture format Auto form at, the picture will fill the screen as much

as possible. See p. 10.

Centre Mode

When you have connected a Dolby audio receiver to the receiver box (see

Connect peripheral equipment, p. 21) and you have selected Centre Mode

O n, the loudspeakers of the monitor will act as centre speaker, making a

separate centre speaker unnecessary.

Warning:When no Dolby audio receiver is connected to the receiver box and you

have selected Centre Mode On, no sound will be heard at all.

To get the sound back, select Centre Mode Off.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

O peration

Use of the rem ote control

Select your com puter or other

peripherals

Press this key repeatedly to select EXT1,

EXT2, EXT3, FRO NT, VGA or TV channels,

according to where you connected your

peripherals (see p. 24).

Standby

Remark: in VGA mode only some keys are valid.

See VGA menu, p. 24.

Menus and on screen information will disappear

if you select VGA.

The set is switched off and the red indicator

lights up in front of receiver box and the

screen.

To switch the TV on again press the B key

or press - P + or the digit keys.

M Mode selection

Press this key repeatedly to indicate the

peripheral equipment you want to operate

with the remote control.

Although this set is provided with low power

standby it is still advised to switch off your TV

overnight instead of leaving it on standby.You

save energy.

TV TV operation

Press this key to use the remote control

directly in the TV mode

VCR 1

VCR 2

DVD

TUNER

TAPE

SAT

V Volum e

AMP

Press + or - to adjust the volume.The

volume is adjusted. If you want to store the

volume adjustment in the memory, see the

Features menu, Sound PP store, p. 15 to

store the same volume adjustment for all

the stored TV channels.

b Dual screen see p. 17

Picture form at

Press this key repeatedly to select another

picture format: 4:3, Movie Expand 14:9,

Movie Expand 16:9 with or without subtitling,

Super Wide,Wide Screen or Auto Format

(when Auto Format is set to Yes in the

SETUP menu).

Program m e selection

To browse through the TV channels and

externals activated in the Favourite

Programme menu.

Auto Format makes the picture to fill the

screen as much as possible.

Super Wide removes the black bars on the

side of 4:3 programmes without causing

apparent distortion.

¬ Sound m ute

Temporarily interrupt the sound or restore

it.

When in Movie Expand 14:9 or 16:9 picture

format, you can make subtitles visible with

the cursor up/down.

Sometimes also video recorder programmes

carry special signals which will automatically

switch the TV to the correct screen format.

0/9 Digit keys

To select a TV channel.

For a two digit programme number, enter

the second digit within 2 seconds.

SMART CONTROLS

PICTURE SOUND

0 Previous program m e

The previously selected TV channel or

external is displayed.

Note: In VGA mode press the q key to switch

between a 4:3, a 16:9 or a Wide VGA picture

format.

In Dual screen mode press the q key to switch

between a full or a squeezed picture format.

i Perm anent program m e num ber

Screen inform ation

Bilingual choice and

sound m ode selection

Press for 3 seconds to activate/de-activate

the continuous display of the programme

number.

Press this key

• to switch from Stereo to Mono sound, in

case of stereo transmission, or from

Digital Sound to Digital Sound Available,

in case of digital transmission;

• to choose between language Y (Dual Y) or

language Z (Dual Z), in case of bilingual

transmission.The setting is separately

stored for each TV channel.

Press briefly to display information about the

selected TV channel or external, its name,

the sound mode, picture format settings, the

selected DNR setting and the remaining time

set with the sleeptimer.

Use of the rem ote control

Download from Www.Somanuals.com. All Manuals Search And Download.

j Continuous subtitles

TV channels with teletext often transmit

certain programmes with subtitling.

Switch on teletext and select the proper

subtitle page from the index.

VCR 1

VCR 2

SAT

TUNER

TAPE

DCC

AMP

Press j to store the subtitle page.

Switch off teletext.

Every time a programme of the selected TV

channel is subtitled, the subtitling will be

available for that channel.

Press j to switch subtitles O n or O ff.

When switched on and the b symbol

appears, there are no subtitles available for

that programme.

PICTURE menu (red key)

SO UND menu (green key)

FEATURES menu (yellow key)

Teletext on/off p. 18

Sm art Keys

To select predefined picture and sound

settings.

Program m e list

Press the blue key to select the programme

list.

PICTURE

SOUND

Picture

Each time it is pressed, a different picture

setting is selected, corresponding with a

specific predefined setting of Colour,

Select the desired TV channel or peripheral

with the cursor in the up/down or left/right

directions and press O K. Programme numbers

from the favourite list are displayed in white

characters. Programme numbers which are not

in the favourite list are displayed in black.

The current TV channel on the screen is

indicated with a black block.

Brightness, Contrast, Sharpness,Tint, DNR,

Colour Temperature and Dynamic Contrast.

The smart picture setting is set to Personal

when one of the picture settings is changed.

Sound

Each time it is pressed, a different sound

setting is selected, corresponding with a

specific predefined setting of Treble, Bass,

Incredible Surround (if stereo sound) and

Spatial (if mono sound).

Centre Mode

Press the white key to switch Centre Mode

On or Off when you have connected a Dolby

audio receiver. See Connect Peripheral

Equipment, Dolby Pro Logic Surround receiver,

p. 21. See also Install TV Setup, p. 9.

Note:When no Dolby audio receiver is connected

and you have switched Centre Mode On, no sound

will be heard at all.

Personal refers to the personal preference

setting of sound which you have stored with

Sound PP store in the FEATURES menu,

p. 15.

The sound setting is set to Manual when one

of the sound settings is changed and until the

personal adjustments are stored or you

switched the TV off and on again.

Remark:The moment you are in a predefined

picture setting and you modify a setting in the

picture menu, all values of the menu will

overwrite the previously made personal setting.

Use of the rem ote control

Download from Www.Somanuals.com. All Manuals Search And Download.

VCR 1

VCR 2

SAT

TUNER

TAPE

DCC

AMP

U Tim e display

The time, downloaded from the TV channel

(with teletext) stored on programme number

1 or the lowest favourite programme number

greater than 1, is displayed in the upper left

corner of the screen.

This function is not available when continuous

subtitles have been switched on.

Video recorder keys see p. 25

Digital Video Disc keys see p. 25

ﬁ

Multi screen

A menu line MO SAIC appears.

Select the desired function with the cursor

left/right and press the O K key.

Scan: the TV channels placed in the favourite

list appear subsequently.

Press the P + key to select a next series of 12

channels.After the selection is finished, press

the c key to make the main picture in the

centre of the screen equal to the active small

picture.The active TV channel or external,

indicated by a red border, can be selected

immediately with the O K key. Multi screen is

left then.

‡

†

Freeze

DVD SELECT

DVD

AUDIO

T-C

When pressed, the displayed picture is

frozen.

Press again to de-activate the frozen picture.

In Dual Screen both pictures are frozen.

P^-

ﬁ

yÚ

Digital Noise Reduction

To reduce the image noise and improve

picture quality when receiving weak signals.

Photo Finish: the main picture is displayed in

successive frozen pictures.

Press the O K key again to have a new

sequence of frozen pictures.

Strobe: the picture is reproduced image by

image.

Press this key to select DNR m in., DNR m ed.

(optimum picture quality for normal strength

signal), DNR m ax. (for poor picture quality)

or DNR off.

Press the O K key again to have a faster speed.

Press the O K key again to return to a noral

picture reproduction.

Press ﬁ to switch off the mosaic screen.

Sound Personal Preferences

Restore sound settings, stored in the features

menu (see p. 15).

Use of the rem ote control

Download from Www.Somanuals.com. All Manuals Search And Download.

VCR 1

VCR 2

DVD

TUNER

TAPE

SAT

Use of the m enus

AMP

& Press the red, green or yellow colour key to display/cancel the PICTURE,

SO UND or FEATURES menu.

é Use the cursor in the up/down directions to select a menu item.

“ Use the O K key to activate.

activate

‘ Press the same menu key again to return or to switch the menu off.

select

adjustments

Picture m enu

Contrast

This control allows you to adjust the contrast levels of the picture.

Brightness

programme list

features menu

This control allows you to adjust the brightness levels of the picture.

Colour

sound menu

This control allows you to adjust the colour saturation of the picture.

picture menu

Sharpness

This control allows you to adjust the edge definiton of a picture.

Sl e e pt i me r

Chi l d Loc k

Sound PP s t or e

Me s s a ge

FEATURES

PI CTURE

Tint (only with NTSC signals)

This control allows you to adjust the colour mix (hue) of a picture.

Ti me r s

Colour Tem perature

This control allows you to select the colour temperature of the picture.

Select Norm al, Cool or W arm with the cursor left/right.

Cont r a s t

Br i ght ne s s

Col our

Sha r pne s s

Dynam ic Contrast

To make the contrast in the darker and the brighter picture areas more

noticeable, it is preferred to select Med or Max.

In certain circumstances it may be preferred to select Min or O ff.

( Ti nt )

Col our Te mpe r a t ur e Nor ma l / Cool / Wa r m

Dyna mi c Cont r a s t

Na t ur a l Mot i on

Natural Motion

Natural Motion O n reproduces smooth movement which makes it more

natural.

After selecting a new TV channel or external, Natural Motion will automatically be

set to On.

Sound m enu

Vol ume

Ba l a nc e

Tr e bl e

Store the modified adjustments for Volume, Balance,Treble and Bass values

and Incredible Surround, as well as the headphone Volume and Balance for all

TV channels with Sound PP store in the FEATURES menu.

SOUND

Ba s s

Sound Mode

Spa t i a l

I nc r e di bl e Sur r ound

He a dphone

Sound m ode

On/ Of f

Your TV will choose between stereo or digital sound depending on the sound

the TV channel transmits, unless you make a sound choice.

In case of weak stereo or digital sound signals, due to the transmission, select

analogue or mono.

Spatial

You can adjust Spatial for each TV channel and external separately.

Spatial can only be selected when the sound of the TV channel or external is

mono.

When Spatial O n is selected, with m ono sound broadcasts, a pseudo-stereo

sound is created by reproducing the mono sound over two channels instead

of one.

Use of the m enus

Download from Www.Somanuals.com. All Manuals Search And Download.

Incredible Surround

Incredible Surround can only be selected when the sound of the TV channel is

stereo.

When Incredible Surround O n is selected, it seems as though the

loudspeakers are spread further apart from one another.

Note: in case you have connected a Dolby audio receiver, select Incredible Surround

Off. In case you have selected Centre Mode On in the Setup menu (see p. 8),

then the items Balance,Treble, Bass, Sound Mode, Spatial and Incredible Surround

are not selectable.

Headphone

See Connect peripheral equipment, p. 21, for the connection of the

headphone.

• Select the source you want to listen to with your headphone: Autom atic, TV,

EXT1, EXT2 or EXT3 (or the names entered in the Give Name menu).

Select Autom atic if you want to listen to the sound of the picture you are

watching on the screen.

Vol ume

Ba l a nc e

Sour c e

HEADPHONE

Note: in the Dual Screen picture, you will hear the sound of the left picture

through your headphone, except if a picture from a connected peripheral has

been selected in the right picture.Then you will hear the sound from the right

picture.

• Select TV when you want to listen to the sound of a TV channel.

• In all other cases select the source where you connected your equipment.

The equipment should be switched on, but you don’t need to watch it.

Use of the m enus

Download from Www.Somanuals.com. All Manuals Search And Download.

Features m enu

VCR 1

VCR 2

DVD

TUNER

TAPE

SAT

& Press the yellow key to display/cancel the FEATURES menu.

é Press the cursor up/down to select a menu item.

“ Press the O K key to activate.

AMP

Sleeptim er

activate

With the sleeptimer you can set a time period after which the TV should

switch itself to standby.

The counter runs from O ff up to 180 m in.

One minute before the TV is set to go to standby, the remaining seconds and

the message Good Night appear on screen. You can always switch off your

set earlier or change the set time.

select

adjustments

Note: when a VGA source is selected, the TV will not go to standby when the

sleeptimer expires.

Child lock

If the child lock is on, the TV can only be switched on with the remote

control.The PRO GRAM - and + keys and VO LUME - or + keys behind the

front door of the receiver cannot be used. In this way you can prevent

unauthorised use of your TV. Also no automatic switching to connected

equipment will occur.

If the message Child lock O n appears, the child lock must be switched off

before you can use the PRO GRAM - and + keys and the VO LUME - or +

keys on the receiver.

features menu

Sl e e pt i me r

Chi l d Loc k

Sound PP s t or e

Me s s a ge

FEATURES

Ti me r s

Sound PP store

The of Volume, Balance,Treble, Bass and Incredible Surround made in the

sound menu and Volume and Balance in the headphone menu can be stored in

memory for all TV channels.

Message

With this function you can enter a personal message on 2 lines which will be

displayed automatically when the set is switched on.

For example: I’ll be late this evening. Don’t wait for dinner.

Me s s a ge

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Change

Press the O K key to start entering the message.

Select with the cursor up/down the letter or number you want to enter.

Select with the cursor right the next position.

Press the O K key when you have entered the complete message.

Cha nge

Cl e a r

Type

MESSAGE

Run

Clear

Press the O K key to remove a previous message.

Type

Press the cursor left/right to select the way the message will be displayed:

W ipe, Slide, Fall or Fade.

The Fade display is a randomly selection of the three other display types.

Run

Press the cursor left/right to select the display frequency: Continuous, O nce

or No.

Use of the m enus

Download from Www.Somanuals.com. All Manuals Search And Download.

Display message

Switch the TV to standby.

The message appears on the screen when the TV is switched on again.

If you selected O nce, the message will disappear from the screen after

about 45 seconds.

If you selected Continuous, the message will appear on the screen until the

Run menu item in the Message menu is switched to No or until the receiver

is powered off.

The message does NOT appear when Continuous subtitles have been

switched On. See p. 11.

Tim ers

Ac t ua l Ti me

Pr ogr a mme

St a r t Ti me

Ca nc e l Ti me r

With the Timers menu you can make your TV automatically switch to a

specific programme number from standby or switch over to a different

programme number at a specific time.

TI MERS

Actual time

If you have installed a TV channel which also broadcasts teletext on

programme number 1 or under the lowest favourite programme number

greater than 1, the time is downloaded from that TV channel.

If this is not the case you have to set the time manually with the digit keys.

The time, (entered manually) is updated every minute and remains until the

TV is switched off with the power key A.

Note: If you entered an incorrect digit, complete the actual time with arbitrary

numbers, then start again. Use 24 hour, or military time.

Programme

Enter with the digit keys the programme number of the TV channel you want

your TV to switch over to.

Start time

Enter with the digit keys the start time of the selected TV programme

number you want your TV to switch over to. Use 24 hour, or military time.

Cancel timer

Select Cancel Tim er and press O K to reset the Start time to --:--

Keys in front of the receiver box

Should your remote be lost or broken you can still browse through the TV

channels and externals or change some of the basic picture and sound

settings with the keys in front of the receiver box.

The PRO GRAM - and + keys enable you to select the TV channels or

externals.

The VO LUME - and + keys enable you to adjust the volume.

Note: If the message Child Lock ON appears, the child lock must be switched off (with

a remote control) before you can use the ^PROGRAM- and + or the VOLUME - or +

keys on the receiver. See p. 15.

Press the LO CAL MENU key behind the door at the front of the receiver

repeatedly to select Volum e, Brightness, Colour, Contrast, Treble or Bass.

Press the VO LUME - or + key to adjust the chosen selection.

The selected adjustment automatically switches off when after 10 sec. no action has

been executed.

LO CAL PRO GRAM

MEN U

VO LUME

Use of the m enus

Download from Www.Somanuals.com. All Manuals Search And Download.

Dual screen

& Press the b key to switch on Dual Screen.

The TV screen will be divided in 2 different pictures.

The picture on the left side is the selected TV channel or external.

The picture on the right side is the picture from the TV channel in the

favourite programme list following or preceding the selected TV channel.

If the b key was selected before, the last selected right picture is displayed

again.

VCR 1

VCR 2

DVD

TUNER

TAPE

SAT

AMP

é Press the q key to select a vertical squeezed or a non vertical squeezed

picture size.

Select left and right pictures

& Press + P - to run through the favourite TV channels and externals in the left

picture.

é Press the dual screen P - or P + keys under the door of the rem ote

control to select the favourite TV channels or an external in the right

picture.

‡

†

P-

P+

Pressing the dual screen P - or P + keys for 3 seconds, starts auto scan down

or up of the TV channels and externals in the right picture.

Press again to stop the auto scan.

DVD SELECT

DVD

AUDIO

T-C

P^-

ﬁ

Remarks

yÚ

• Programmes via a decoder/descrambler can only be displayed in the

left picture.

• Programmes in the subpicture via a peripheral (e.g. videorecorder) can be heard

via the headphone.

• VGA can not be displayed in Dual screen mode.

• On screen sound information of the left main picture appears in the right

upper corner.

Switch screens

Press the c key to swap the right and left picture.The sound is swapped as

well.

Select still picture

Press the S key to freeze the programmes on the left and the right picture.

Press the S key again to de-activate the still pictures.The screen remains in

dual screen mode.

Press the d key to freeze only the programme in the right picture.

If the screen was not in Dual Screen mode, the Dual Screen mode is entered,

and the displayed picture on the left is re-displayed on the right side in a

frozen way.

BBC 1

EXT 2

EXT2

BBC 2

EXT 2

BBC 1

EXT1

Press the d key again to de-activate the still picture.The screen remains in

dual screen mode.

Possible Dual Screen com binations

TV channel/TV channel

See Select left and right pictures.

TV channel/Peripheral

See Select left and right pictures.

Peripheral/TV channel

See Select left and right pictures.

Peripheral/Peripheral

See Select left and right pictures.

Dual screen

Download from Www.Somanuals.com. All Manuals Search And Download.

Teletext

Most TV channels broadcast information via teletext.

VCR 1

VCR 2

DVD

TUNER

TAPE

SAT

Each channel which broadcasts teletext transmits a page with information on

how to use its teletext system. Look for the teletext page with the main

index (usually p. 100).

AMP

Depending on the TV channel, teletext is transmitted in different systems:

WST, FLOF or TOP.

The colours used in the options lines at the bottom right of the screen

correspond with the colour keys of your remote control.

About Easy Text

Easy Text considerably reduces the waiting time (on condition that the

teletext broadcast of the particular TV channel is received for at least half a

minute) by :

•

a direct selection of previous and following pages which are in transmission

and of the pages referred to in the options lines

•

a habit watcher list: frequently used pages are put automatically in a list of

preferred pages, so that they are immediately available

•

the precapturing of the page numbers referred to in the displayed page

the precapturing of all the subpages.

Switch Teletext on and off

Press b to switch the teletext on or off.

The main index page appears on the screen.

Note: Dual Screen is disabled in Teletext mode.

Select a Teletext page

W ith the digit keys

Enter the desired page number with the digit keys.

The page counter seeks the page or the page appears immediately when the

page number has been stored in the memory.

p 100

News

Sports

Weather

TV-Guide

t x t

A message appears when you have entered a non existent or incorrect page

number. Page numbers beginning with 0 or 9 do not exist. Choose another number.

W ith the option lines

Select with the colour keys, corresponding to the coloured options at the

bottom right of the screen, the desired subject.

Q uickly run through the teletext pages

Press the cursor left/right or the - P + key to run through the previous or

the following pages.

Select the previously selected txt page

Press the 0 key.

Teletext

Download from Www.Somanuals.com. All Manuals Search And Download.

Select the index teletext page

Press the k key to display the main index (usually p.100).

VCR 1

VCR 2

DVD

TUNER

TAPE

SAT

O nly for T.O.P teletext broadcasts :

T.O.P orders the pages in categories and adds other possibilities of enhancing

ease of use.

AMP

Press i. A T.O.P. overview of the teletext subjects available is displayed.

Not all TV channels broadcast T.O.P. teletext.When the teletext system

is not T.O.P. teletext, a message appears at the top right of the screen.

Select with the cursor up/down, left/right the desired subject and press the

O K key.

Select subpages

When a selected teletext page consists of different subpages, one of the

subpages appears on the screen.

The coloured number in the vertical bar at the right of the screen refers to

the displayed subpage.

The other subpages can be selected in 2 ways :

‡

†

W ith the cursor up/down

DVD SELECT

DVD

The other subpage numbers appear in white as soon as the transmission has

found them.They are stored in the memory so that they are available while

the teletext page is on screen.

AUDIO

T-C

P^-

ﬁ

Select with the cursor up/down the previous or the following subpage.

yÚ

By adding a subcode

Press U. Enter the desired subpage with the digit keys : e.g. 3 for the third

page of seven subpages.

The TV searches for the selected subpage.

Automatically rotating subpages:

Press U again to cancel the subcode.

Now the subpages rotate automatically.

Press U again.A vertical bar with the available subpages reappears again.

Select the subpages with the cursor up/down.

Special teletext functions

Interrupt

Press e and the TV programme appears.

The display b indicates that you are still in the teletext mode.

You can select a page number.

Press e again to display the teletext page.

Mix

Press c to overlay the teletext page on the TV programme.

Press c again to display only the teletext page.

Enlarge

Press h repeatedly to display the upper part, the lower part and then to

return to the normal page size.

Reveal

Press f to reveal/conceal the hidden information, such as solutions to

riddles and puzzles.

Teletext

Download from Www.Somanuals.com. All Manuals Search And Download.

Connect Peripheral Equipm ent

There is a wide range of audio and video equipment that can be connected

to your receiver.The following connection diagrams show you how to

connect them to the back or the front side of the receiver.

Note: in case of the monitor in a stand alone situation without the receiver box

connected, see the instructions with the monitor.

Video recorder

Note: Do not place your video recorder too close to the screen as some video

recorders may be susceptible for signals out of the display. Keep a minimum distance

of 0.5 m to the screen.

Connect the supplied aerial cables 1, 2 and, to obtain a better picture

quality, a eurocable 3 as shown opposite.

If your video recorder is provided with the EasyLink function, the eurocable supplied

with it, should be connected to EXTERNAL 2 to benefit of the EasyLink function.

Only if you do not connect the eurocable 3, you have to do the following :

Search for and store the test signal of the video recorder

CABLE

& Unplug the aerial cable 1 from the aerial socket x of your video recorder.

EXTERN AL

é Switch on your TV and put the video recorder on the test signal.

(See the handbook for your video recorder.)

“ Search for the test signal of your video recorder in the same way as you

searched for and stored the TV signals. See Installation, Searching for and

storing TV channels, Manual Installation, p. 6.

‘ Store the test signal under programme number 0 or between 90 and 99.

( Replace the aerial cable in the aerial socket x of your video recorder after

VCR 1

DECODER

you have stored the test signal.

Decoder and video recorder

Connect a eurocable 4 to your decoder and to the special euroconnector

of your video recorder. See also the video recorder handbook.

See Define Decoder/Descrambler prog. numbers, p. 8.

You can also connect your decoder directly to EXTERNAL 1 or 2 with a

eurocable.

Video recorder and other peripherals

& Connect the aerial cables 1, 2 and 3 as shown opposite. Better picture

quality can be obtained if you also connect eurocable 5 to EXTERNAL 2

and a eurocable 4 to EXTERNAL 1 or 3.

EXTERN AL

CABLE

1 2

é Look for the test signal of your peripheral in the same way as you do for a

video recorder.

When a video recorder is connected to EXTERNAL 1 you can only record a

programme from your TV.

Only when a video recorder is connected to EXTERNAL 2 it is possible to record a

programme from your TV as well as from other connected equipment. See Record

with your video recorder, p. 26.

Note: EXTERNAL 1 can handle CVBS and RGB, EXTERNAL 2 CVBS,Y/C and RGB,

EXTERNAL 3 only CVBS.

VCR 1

Connect Peripheral equipm ent

Download from Www.Somanuals.com. All Manuals Search And Download.

Cam era & cam corder

& Connect your camera or camcorder at the front side of your receiver.

é Connect the equipment to VIDEO 2 and AUDIO L 1 for mono

equipment.

“ For stereo equipment also connect AUDIO R 1.

S-VHS quality with an S-VHS camcorder is obtained by connecting the S-VHS

cables with the S-VHS input 3 and AUDIO inputs 1.

Headphone

& Insert the plug into the headphone socket L at the front side of the

receiver.

é Press ¬ to switch off the internal loudspeakers of the TV.

The headphone impedance must be between 8 and 2000 Ohm.

The headphone socket has a 3.5 mm jack.

In the SO UND menu select Headphone to adjust the headphone volume and

balance and to select the audio source for your headphone sound. See p. 14.

Dolby Pro Logic Surround receiver

& Connect the audio cable to the Dolby Pro Logic Surround receiver and to

AUDIO O UT L and R at the back of your receiver box 1.

é If you want the loudspeakers of your monitor to act as centre speaker, also

connect an audiocable to the Dolby Pro Logic Surround receiver and to the

SURRO UND SO UND CENTRE IN at the back of your receiver

box 2.

AUDIO OUT

SURRO UND

SO UND CENTRE IN

“ Select Centre m ode O n in the Setup menu. See p. 9, or switch Centre Mode

O n with the white colour key on the remote control.

In the Sound menu only the volume menu item can be controlled.

The loudspeakers of the monitor will now only produce centre sound, the

loudspeakers connect to the audio receiver will produce Surround Sound.

If you want to connect more equipment to your receiver, consult your dealer.

Connect Peripheral equipm ent

Download from Www.Somanuals.com. All Manuals Search And Download.

Connect your com puter

& Connect one end of a VGA cable supplied to the video card of the computer

and the other end to the VGA MO NITO R IN connector at the rear side of

the receiver box or at the VGA IN connector 1 at the back of the monitor

in case you have no receiver box connected to the monitor.

See the instructions with the monitor.

é Fix the connectors firmly with the screws on the plug.

“ In case of a Multimedia computer, connect audio cables to the audio outputs

of your Multimedia computer and to the AUDIO MO NITO R IN R (right) and

L (left) above the VGA MO NITO R IN connector at the back of the receiver

or to the AUDIO IN L and R 2 at the back of the monitor.

MAINS INLET

AUDIO IN

AUDIO OUT

VGA OUT

VGA IN

Connect your Apple Macintosh* com puter

Attention: Macintosh computers with separate H and V synchronisation signals

can be used together with a switchable adaptor. Macintosh computers with

Composite Sync and Sync on Green signals may need another special adaptor or

cable. Contact your dealer.

& Connect the switchable adaptor for Apple video connectors to one end of a

VGA cable.

é Put the DIP switches on the adaptor in the following positions :

off

“ Connect the end of the VGA cable with the adaptor to the video card of the

computer and the other end to the VGA MO NITO R IN connector on the

back of the receiver box or at the VGA IN connector on the back of the

monitor in case you have no receiver box connected.

‘ Screw the connectors down firmly.

15-pin D sub

(2-row)

15-pin mini D sub

(3-row)

To reproduce computer screen information and/or programmes, see p. 25.

Apple Macintosh is a registered trademark of Apple Computer, Inc.

Connect your com puter

Download from Www.Somanuals.com. All Manuals Search And Download.

Daisy chaining

The Active Loop Through facility makes it possible to make a daisy chain.

Connect the monitors (max. 2) before inserting the m ains plug in the

wall socket.

Connect another VGA cable to the VGA O UT connector 1 at the back of

the monitor and to the VGA IN connector of a second VGA monitor.

MAINS INLET

AUDIO IN

AUDIO OUT

VGA OUT

VGA IN

In case of a Multimedia computer, also connect the audio cables to AUDIO

O UT R and L 2 next to the VGA O UT connector and to the audio inputs of

the second VGA monitor.

Computer Display modes

VGA

640x480

640x400

640x350

856x480

800x450

640x480

800x600

1024x768

31.468 kHz

31.490 kHz

35.000 kHz

35.156 kHz

37.880 kHz

45.000 kHz

48.360 kHz

60 Hz

70 Hz

60 Hz

65 Hz

67 Hz

56 Hz

60 Hz

56 Hz

60 Hz

VGA

MAC II

SVGA

XGA

When a VGA computer is connected, the selection is made automatically.

A message is displayed when the monitor does not support one of the above

mentioned VGA modes.

Switch your computer to a correct display mode.

Connect your com puter

Download from Www.Somanuals.com. All Manuals Search And Download.

To select connected equipm ent

If the monitor is connected to a video recorder with the EasyLink function, in some

cases the monitor will be switched on, even when it was in standby. (E.g. playback

tape,...)

This is not possible when Child lock On is selected.

Equipm ent connected with an aerial cable only :

Select the programme number under which you have stored the test signal

with the digit keys.

Equipm ent connected to a euroconnector, to the VGA MO NITO R IN

connector or to the front side of the receiver box

Press the w key repeatedly to select EXT1, EXT2, EXT3, FRO NT or VGA,

according to where you connected your equipment at the back or the front

side of your receiver.

VCR 1

VCR 2

DVD

TUNER

TAPE

SAT

AMP

Remark : Most equipment (decoder, video recorder) carries out the switching itself.

ZOOM

If you want to change to TV channels?

Enter the programme number of the TV channel which you want to watch

with the digit keys.

VGA m enu

& Select VGA with the w key.

é Press the red (picture menu), green (sound menu) or yellow (features menu)

key on the door of the remote control to switch on the VGA menu

(or press the MENU key on the simplified remote control).

“ Select one of the PC symbols with the cursor up/down:

for contrast,

for brightness,

for colour temperature,

for horizontal picture position,

for vertical picture position,

for volume.

‘ Press the cursor left/right to alter the selected adjustment.

( Press one of the coloured keys again (or the MENU key on the simplified

remote control) to switch off the VGA menu.

Connect peripheral equipm ent

Download from Www.Somanuals.com. All Manuals Search And Download.

Video recorder keys

VCR 1

VCR 2

DVD

TUNER

TAPE

SAT

Most of the audio and video equipment from our range of products can be

operated with the extended remote control.

AMP

Press the M key repeatedly until the arrow in the display indicates VCR1 for

your video recorder or another designation according to other equipment

you want to operate with this remote control.

Press one of the video recorder keys:

‡

for stop,

for rewind,

for play,

†

for fast forward,

for programming (on certain models),

for record,

‡

†

- P +

0-9

for fast programme selection from the video recorder tuner,

to select a programme number from your video recorder,

to switch off the video recording temporarily.

DVD SELECT

DVD

AUDIO

T-C

P^-

ﬁ

yÚ

These keys function with Philips video recorders.

If your video recorder has the EasyLink function, the keys ® and ‡ for record and

stop under the door of the TV remote control, can be operated in the TV mode.

DVD (Digital Video Disc) keys

VCR 1

VCR 2

DVD

AMP

TUNER

TAPE

SAT

Press the M key repeatedly until the arrow in the display indicated DVD for

your digital video disc.

Press one of the DVD keys:

T- C

‡

to switch the DVD menu on or off,

to select a DVD chapter,

+ a digit key to select a DVD title,

for stop,

for rewind,

for play,

†

for fast forward,

for slow forward. Press repeatedly to select the speed,

‡

†

AUDIO to select your choice of audio language,

DVD SELECT

DVD

to select your choice of subtitle language (only in DVD mode)

AUDIO

T-C

P^-

0-9

to select a programme number from your DVD.

ﬁ

yÚ

These keys function with Philips DVD players.

Connect peripheral equipm ent

Download from Www.Somanuals.com. All Manuals Search And Download.

Record with your video recorder without EasyLink

Ext2 O utput

To record S-VHS quality, connect an S-VHS peripheral directly to the video

recorder.

In this case go on as follows:

& Select Setup in the INSTALLATIO N menu and press the O K key.

é Select Ext 2 O utput with the cursor up/down.

“ Select S-VHS Q uality with the cursor left/right.

In all other cases, whether you record with a VHS or a S-VHS video recorder,

select VHS Q uality.

‘ Press one of the colour menu keys on the door of the remote control

repeatedly to switch the menu off.

Record a TV program m e

& Select the programme number on your video recorder.

é Set your video recorder to record.

See the handbook for your video recorder.

Switching programme numbers on your TV does not disturb recording !

Record a program m e on your video recorder connected to

EXTERNAL 2 from Audio/Video equipm ent connected to

EXTERNAL 1, EXTERNAL 3 or to sockets on the front side of the

receiver

& Switch on the equipment.

é Select the correct external on your video recorder.

“ Set your video recorder to record.

You record what you are watching on the screen.

Do not switch programme numbers or do not switch off your TV when you are

recording !

Record

Download from Www.Somanuals.com. All Manuals Search And Download.

Record with your video recorder with EasyLink

If you have connected an S-VHS video recorder provided with the EasyLink function,

you can record S-VHS-quality from an S-VHS peripheral connected to the front side

of the receiver. (E.g. from an S-VHS camcorder.)

SOUND

In TV mode, it is possible to start a direct recording of the programme which is being

displayed on the TV screen.

TXT

‡

T-C

& Press the INSTANT ® record key, under the door of the remote control of the TV

or of the video recorder or the record key on the video recorder..

The video recorder switches on from standby and a message of what is being

recorded appears on the screen.

†

AUDIO

P^-

ﬁ

The video recorder starts recording the programme you are watching.

yÚ

Switching programme numbers on your TV does not disturb recording !

é Press the ‡ key to stop the recording.

When recording a programme from a peripheral connected to ^EXTERNAL1, 3 or

FRONT, you can not select another TV programme on the screen.

To watch TV programmes again, press the programme number you want to select

twice.

Attention: the recording is stopped and your video recorder switches to standby.

If you switch to standby during recording of a programme from a peripheral

connected to ^EXTERNAL1, 3 or FRONT, the blinking lamps on the front of your receiver

indicate that you are still recording.The blinking stops after the recording is finished.

Record

Download from Www.Somanuals.com. All Manuals Search And Download.

Tips

Poor Picture

• In case of weak or bad signal, consult your

End of life directives

dealer.

We are paying a lot of attention to using

environmentally-friendly production

methods.Your new flat colour television

contains materials which can be recycled and

reused.

At the end of life specialised companies can

dismantle the discarded flat colour television

to concentrate the reusable materials and to

minimise the amount of materials to be

disposed of.

• Have you selected the correct TV system?

• Is your monitor or house aerial located

too close to loudspeakers, non-earthed

audio equipment or neon lights, etc. ?

• Mountains or high buildings can cause

double pictures or ghost images.

Sometimes you can improve the picture

quality by changing the direction of the

outside aerial.

• Check if you have entered the correct

frequency. See Installation, p. 6.

• Are brightness and contrast out of

adjustment ? Adjust the picture settings,

see p. 13.

• Sometimes poor picture quality is possible

when having activated a S-VHS camera or

camcorder connected to the front side of

your receiver and another peripheral is

connected to EXT1 or EXT2 at the

same time. In this case switch off one of

the other peripherals.

Control of peripheral equipm ent

The infrared signals of the screen may

influence the reception sensibility of other

peripherals.

Solution: replace the batteries of the remote

control or change position of other

equipment. E.g. keep away a wireless

headphone from within a radius of 1.5 m.

Please ensure you dispose of your old flat

colour television according to local

regulations.

Rem ote control

• If your monitor no longer responds to the

remote control, the batteries may be

exhausted.

• You can still use the keys at the front of

your receiver.

How to dispose of exhausted batteries?

The batteries supplied do not contain the

heavy metals mercury and cadmium.

Nevertheless in many countries exhausted

batteries may not be disposed of with your

household waste. Please ensure you dispose of

exhausted batteries according to local

regulations.

Have you selected the wrong menu ? Press

the same key again to exit from the menu.

No picture or no sound

No stable or not synchronised VGA

picture

Check if you have selected the correct VGA

mode in your PC (640x480, 640x400,

640x350, 856x480, 800x450, MAC II, SVGA,

XGA).

Miscellaneous

• Are the supplied cables connected

properly? (The aerial cable to the monitor,

the other aerial to your VCR, the VGA

cables to the display, the power cables.)

• Has the child lock (p. 15) been switched

off ?

. Ambient temperature: + 5~ + 45°C

. Maximum operating altitude: 2000 m

. Mains:AC 100-240V

. Power consumption: around 350W

. Standby consumption: 2 W

. Weight (excl. packaging)

Display: 42.5 kg

Receiver: 6.4 kg

. Dimensions (wxhxd):

Display: 122.2 x 68.1 x 14.6 cm

Receiver: 43.5 x 16.7 x 33.8 cm

. Wall mounting bracket included

. Flour stand optional

• Is your PC switched on?

If your problem is not solved:

• Has the Centre mode been switched off?

See Install TV Setup, Centre Mode, p. 9, or

press the white colour key on the remote

control.

• Do you see a black screen and the

indicator in front of the monitor lights up

green, this means that the display mode is

not supported. Switch your VGA-source to

a correct mode.

Switch both your monitor and your receiver

off and then on again.

Never attem pt to repair a defective

m onitor or receiver yourself.

Check with your dealer or call a TV technician.

Index

auto format, 9

automatic installation, 6

ACI, 6

bilingual broadcast, 10

camcorder, 21

centre mode, 9

child lock, 15

clock, 12

colour temperature, 13

computer, 22

freeze, 12

frequency, 6

give name, 7

headphone, 21

info on screen, 10

information line, 9

interrupt the sound, 10

language, 5

setup, 9

simplified remote control, 4

sleeptimer, 15

smart controls, 11

sound adjustments, 13

sound mode, 13

sound personal preferences, 12

sound pp store, 15

stereo, 10

store TV channels, 6

subpages teletext, 19

subtitles, 11

S-VHS, 26

switch TV on, 3

teletext, 18

timers, 16

tint, 13

m manual installation, 6

menu language, 5

message, 15

country, 5

daisy chaining, 23

decoder/descrambler, 8

digital, 10

DNR, 12

dual screen, 17

dvd keys, 25

peripheral equipment, 20

permanent programme number, 10

picture adjustments, 13

picture format, 10

picture mute, 9

programme list, 11

dynamic contrast, 13

easy text, 18

recording, 26

reshuffle, 7

VGA, 24

video recorder, 20

eurocable, 20

favourite programmes, 7

search for TV channels, 6

select your computer, 24

Tips & Index

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary

100 Hz

DNR

Picture Freeze

100 Hertz provides a superior solution to

the problem of picture flicker which is

particularly noticeable with larger screen

sizes. In a conventional TV, the picture area

is scanned 50 times a second (50 Hertz) –

a frequency which is still detectable by the

human eye in the form of a flickering

picture. In 100 Hertz sets, the picture area

is scanned at a rate of 100 times per

second (100 Hertz).At this frequency, the

eye cannot detect flicker, resulting in a

clearer picture which is more relaxing to

the eye.

Dynamic Noise Reduction.

TV mode which allows you to “freeze” a

certain image in order to study a specific

detail at ease, e.g. to make notes of certain

programme information like phone

numbers.

By encoding signals digitally in 100 Hz sets

with Digital Scan it is possible to clean up

picture noise.This is especially beneficial in

poor signal areas and when viewing poor

quality video tapes.

Sm art Picture and Sound Controls

Easy Link

Keys on the remote control to select

predefined picture and sound settings.

Digital ‘intelligent’ ESI bus-system between

audio components in HiFi systems and

between TV and VCR. (Scart connection

required).Turns source selection and

control into a one-button operation.

Sleeptim er

Function with which you can set a time

period after which the TV should switch

itself to standby.

Autom atic Channel Installation (ACI)

Automatically installs all TV channels in

the same order as offered by your cable

company, provided of course that the data

is transmitted. It also automatically

includes programme number and

programme name.

EasyText

Teletext memory that automatically

memorises Teletext pages and gives you

instant access to them.

Teletext