BDL5530EL
EN User manual
Cleaning and troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL5530EL
Service:
• The casing cover should be opened only by qualified service personnel.
• If there is any need for repair or integration, please contact your local service center.
• Do not leave your display under direct sunlight.
If your display does not operate normally, having followed the instructions set out in this document, please
contact a technician or your local service center.
Read and follow these instructions when connecting and using your display:
• Unplug the display if you are not going to use it for an extensive period of time.
• Unplug the display if you need to clean it with a slightly damp cloth. The screen may be wiped
with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based
liquids.
• Consult a service technician if the display does not operate normally after having followed the
instructions in this manual.
• The casing cover should be opened only by qualified service personnel.
• Keep the display out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into the vents or prevent proper cooling of the display’s
electronics.
• Do not block the ventilation holes on the cabinet.
• Keep the display dry. To avoid electric shock, do not expose it to rain or excessive moisture.
• When turning off the display by detaching the power cable or DC power cord, wait for 6
seconds before re-attaching the power cable or DC power cord for normal operation.
• To avoid the risk of shock or permanent damage to the set do not expose the display to rain or
excessive moisture.
• When positioning the display, make sure the power plug and outlet are easily accessible.
• IMPORTANT: Always activate a screen saver program during your application. If a still image in
high contrast remains on the screen for an extended period of time, it may leave an “after-
image” or “ghost image” on the front of the screen. This is a well-known phenomenon that is
caused by the shortcomings inherent in the LCD technology. In most cases the afterimage will
disappear gradually over a period of time after the power has been switched off. Be aware that
after-image symptoms cannot be repaired and are not covered under warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL5530EL
REGULATORY INFORMATION
CE DECLARATION OF CONFORMITY
MMD declares under our responsibility that the product is in conformity with the following standards
• EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment)
• EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment)
• EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment)
• EN61000-3-2:2006 (Limits for Harmonic Current Emission)
• EN61000-3-3:1995+A1:2001+A2:2005 (Limitation of Voltage Fluctuation and Flicker)
• EN55013:2001+A1:2003 +A2:2006 (Limits and Methods of Measurement of Radio Disturbance Characteristics of
Broadcast Receivers and Associated Equipment)
• EN55020:2007 (Electromagnetic Immunity of Broadcast Receivers and Associated Equipment)
following provisions of directives applicable
• 2006/95/EC (Low Voltage Directive)
• 2004/108/EC (EMC Directive)
• 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on
ISO9000 level.
FEDERAL COMMUNICATIONS COMMISSION (FCC) NOTICE (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the users’
authority to operate the equipment.
Use only RF shielded cable that was supplied with the display when connecting this unit to a computer device. To prevent
damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-CAUSING
EQUIPMENT REGULATIONS.
FCC DECLARATION OF CONFORMITY
Trade Name: Philips
Declaration of Conformity for Products Marked with FCC Logo, United States Only: This device complies
with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL5530EL
POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All
equipment that works together (computers, monitors, printers and so on) should have the same power supply source.
The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the
form of a fuse with a nominal value no larger than 16 Amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which
should be located near the equipment and easily accessible.
A protection mark “B” confirms that the equipment is in compliance with the protection usage requirements of
standards PN-93/T-42107 and PN-89/E-06251.
ELECTRIC, MAGNETIC AND ELECTRONMAGNETIC FIELDS (“EMF”)
1. MMD manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general
have the ability to emit and receive electromagnetic signals.
2. One of MMD’s leading Business Principles is to take all necessary health and safety measures for our products, to
comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of
producing the products.
3. MMD is committed to developing, producing and marketing products that cause no adverse health effects.
4. MMD confirms that if its products are handled properly for their intended use, they are safe to use according to
scientific evidence available today.
5. MMD plays an active role in the development of international EMF and safety standards, enabling MMD to anticipate
further developments in standardization for early integration in its products.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL5530EL
INFORMATION FOR UK ONLY
WARNING - THIS APPLIANCE MUST BE EARTHED.
Important:
This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this
type of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A, A.S.T.A. or BSI approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an
appropriate 3-pin plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse
is used, the fuse at the distribution board should not be greater than 5A.
Note: Any severed plug must be destroyed to avoid a possible shock hazard should it
be inserted into a 13A socket elsewhere.
How to connect a plug
The wires in the mains lead are colored in accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN & YELLOW - “EARTH” (‘E”)
1. The GREEN AND YELLOW wire must be connected to the terminal in the plug
which is marked with the letter “E” or by the Earth symbol or
or GREEN AND YELLOW.
coloured GREEN
2. The BLUE wire must be connected to the terminal which is marked with the letter
“N” or coloured BLACK.
3. The BROWN wire must be connected to the terminal which marked with the letter
“L” or coloured RED.
Before replacing the plug cover, make certain that the cord grip is clamped over the
sheath of the lead - not simply over the three wires.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL5530EL
中国电子信息产品污染控制表示要求 ( 中国 RoHS 法规标示要求 ) 产品中有毒有害物质或元素
的名称及含量
有毒有害物质或元素
六价铬
+
铅
(Pb)
O
X
X
部件名称
汞
(Hg)
镉
(Cd)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
(Cr 6 )
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
外壳
液晶面板
电路板组件
附件
X
X
O
O
O
O
O
O
O
O
O
O
( 遥控器，电源线，连接线 )
遥控器电池
O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
环保使用期限
此标识指期限 ( 十年 )，电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外泄或突变，
电子信息产品用户使用该电子信息产品不会对环境造成严重污染或对其人身、财产造成严重损害的期限。
《废弃电器电子产品回收处理管理条例》提示性说明
为了更好地关爱及保护地球，当用户不再需要此产品或产品寿命终止时，请遵守国家废弃电器电子产品回收处
理相关法律法规，将其交给当地具有国家认可的回收处理资质的厂商进行回收处理。
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL5530EL
NORTH EUROPE (NORDIC COUNTRIES) INFORMATION
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN
UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
END-OF-LIFE DISPOSAL
Your display contains materials that can be recycled and reused. Specialized companies can recycle your product to
increase the amount of reusable materials and to minimize the amount to be disposed of.
Please find out about the local regulations on how to dispose of your old display from your local Philips dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local state and federal regulations. For
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT-WEEE
Attention users in European Union: private households
This marking on the product or on its packaging illustrates, under European Directive 2002/96/EG governing
used electrical and electronic appliances, that this product may not be disposed of with normal household
waste. You are responsible for the disposal of this equipment through a designated waste electrical and
electronic equipment collection. To determine the locations for dropping off such electrical and electronic
waste, contact your local government office or the waste disposal organization that serves your household
area.
Attention users in United States:
Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and Federal
END OF LIFE DIRECTIVES - RECYCLING
Your display contains several materials that can be recycled for new uses.
Like all LCD products, this set contains a lamp with Mercury, please dispose of according to all local State
and Federal laws.
R
R
As an ENERGY STAR Partner, MMD has determined that this product meets the ENERGY STAR guidelines
for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL5530EL
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL5530EL
1. UNPACKING AND INSTALLATION
1.1. UNPACKING
• This product is packed in a carton, together with the standard accessories.
• Any other optional accessories will be packed separately.
• Due to the size and weight of this display it is recommended for two people to move it.
• The protective glass and glass substrate are installed on the front of the product. Since glass can be both broken and
scratched easily, the product should be handled with care. Never place the product with the glass faced down unless
with proper protection and padding.
1.2. PACKAGE CONTENTS
Verify that you received the following items with your package content:
1. LCD display
2. Remote control with batteries
BDL5530EL
BDL5530EL
3. CD-ROM (EDFU and SICP)
4. Quick Start Guide
5. Cable retainer (x 3)
6. Power cords
1
2
3
4
5
7. VGA cable
7
6
• For regions not covered by our standard power plugs, apply a power cord that conforms to the AC voltage of the
power socket and has been approved by and complies with the safety regulations of the particular country.
• The package box and material can be saved for any event where the unit needs to be shipped to another location.
• External speakers and table stands are offered as optional extras, and are not included with your display.
1.3. INSTALLATION NOTES
• Due to the high power consumption of the display, always use the plug exclusively designed for this product. If an
extended line is required, please consult your service agent.
• The product should be installed on a flat surface to avoid tipping. Maintain a distance of at least 6cm between the back
of the display and the wall for proper ventilation. Avoid installing the unit in a kitchen, bathroom or any other place
with high humidity so as not to shorten the service life of the electronic components.
• Do not place this product on the floor and keep away from children.
• The product can normally operate only under 4000m in altitude. In installations at altitudes above 4000m, some
abnormalities may be experienced.
User Manual BDL5530EL
1.4. PORTRAIT MOUNTING
Wall mounting holes
Notes:
Note: The remote control sensor should be on the right side
when rotating your display.
• M6 (10mm) screws (with a length 10-15mm longer than
the thickness of the mounting bracket) are needed for wall
mounting (not included). Tighten the screws securely
(recommended torque: 470 - 635N cm)
• The mounting interface should comply with the UL1678
standard in North America. The mounting means should be
strong enough to bear the weight of the display (approx. 29
kg (63.9 lb) without stands).
Allowable tilting angle in Portrait Mode
Note: When installing the display on the wall, please consult a professional technician
for proper installation. The manufacturer accepts no liability for installations not
performed by a professional technician.
User Manual BDL5530EL
2. PARTS AND FUNCTIONS
2.1. FRONT VIEW
1
1. Remote control sensor, ambient light sensor and power indicator
• Receives command signals from the remote control.
• Detects the ambient lighting conditions around the display.
• Indicates the operating status of the unit:
- lights green when the display is turned on
- lights red when the display is in standby mode
- blinks green when remote control signal is received
- blinks red when the display enters DPMS mode
- off when the main power of the display is turned off
User Manual BDL5530EL
2.2. REAR VIEW
1
2
3
4
5
6
100 mm
Dent depth:
6.5 mm
38 mm
225 mm
235 mm
7
8
1. VIDEO SOURCE button
• Use this button to select the input source.
• When the On Screen Display menu is active, this is also used as the SET button.
2. MENU button
• Use this button to engage the On Screen Display menu.
• When the On Screen Display menu is active, use this button to return to the previous menu.
3. / button
• When the On Screen Display menu is active, use these as the UP/DOWN menu buttons.
• Press and hold the and buttons simultaneously for 3 seconds to lock or unlock all buttons.
4. / button
• When the On Screen Display menu is active, use these as the PLUS/MINUS menu buttons.
5. POWER button
Use this button to turn the display on or into standby mode.
6. Power indicator
Indicates the operating status of the unit:
- lights green when the display is turned on
- lights red when the display is in standby mode
- blinks red when the display enters DPMS mode
- off when the main power of the display is turned off
7. Smart Insert installation holes
Location for the Smart Insert (for integration of a small form factor PC) and M4 screws. (Maximum
load: 2kg)
8. Cable retainer installation holes
Install the cable retainer using these holes.
User Manual BDL5530EL
2.3. INPUT/OUTPUT TERMINALS
12
7
1
2
3
4
5
6
8
9
10
11 13
14
15
16
1. AUDIO IN (AUDIO1)
9. RS-232C (OUT/IN)
Connects to the audio output of a computer.
RS232C network connection input/output for the use of
loop through function.
2. AUDIO OUT R/L
Outputs the audio signal from the AUDIO IN
(AUDIO1/AUDIO2/AUDIO3) or HDMI jack.
10. VIDEO IN (COMPONENT)
Component video input (YPbPr) for connecting to the
component output of an AV device.
3. SPEAKERS R/L
Outputs the audio signal from the AUDIO IN
(AUDIO1/AUDIO2/AUDIO3) or HDMI jack to
external speakers.
11. VIDEO IN (S-VIDEO)
S-Video input for connecting to the S-Video output of an
AV device.
4. AUDIO IN (AUDIO2/AUDIO3)
12. VIDEO OUT
Connects to the audio output of an AV device.
Connects to the video input of an AV device or another
BDL5530EL unit.
5. VIDEO IN (HDMI)
Connects to the HDMI output of an AV device or to the
DVI-D output of a PC. (Using a DVI-HDMI cable)
13. VIDEO IN
Connects to the video output of an AV device or
another BDL5530EL unit.
6. VIDEO IN (DVI-D)
Connects to the DVI-D output of a PC or to the HDMI
output of an AV device (Using a DVI-HDMI cable).
14. Main power switch
Press to switch the main power on/off.
7. VGA OUT
15. AC IN (4.0 A)
Outputs the VGA signal from the VGA IN jack.
Connects the supplied power cord to the wall outlet.
8. VGA IN
16. AC OUT (2.0 A)
Connects to the VGA output of a computer.
Can be used to power an external media device.
User Manual BDL5530EL
2.4. REMOTE CONTROL
2.4.1. GENERAL FUNCTIONS
POWER button
Press to switch on the display from standby mode. Press again to turn it to
standby mode.
SMART button
To select smart picture mode from:
• Highbright: for moving images such as Video
• Standard: for images (factory setting)
• sRGB: for text based images
• Cinema: for movies.
• User: create your own picture settings. This mode is automatically selected
after you change the settings in the Picture menu.
VIDEO SOURCE button
Press to open the video source selection menu and then press UP/DOWN to
select from HDMI, DVI-D, VGA, Component, S-Video, and Video.
AUDIO SOURCE button
Press to open the audio source selection menu and then press UP/DOWN to
select from HDMI, Audio 1, Audio 2, and Audio 3.
Picture format button
To switch screen aspect ratio between Full, Normal, Dynamic, Custom,
Real, and 21:9.
PIP (Picture In Picture) buttons
•
•
•
ON/OFF button: To turn PIP mode on/off.
INPUT button: To select the input signal for the sub-picture.
CHANGE button: To toggle between the main picture and sub picture.
Note: “PIP” mode does not work if the screen size is set to “Custom”, “Dynamic”, “Real”
or “21:9”.
CONTRAST button
Press to open the Contrast OSD selection, and then press the PLUS or
MINUS button to adjust the value.
BRIGHTNESS button
Press to open the Brightness OSD selection, and then press the PLUS or
MINUS button to adjust the value.
User Manual BDL5530EL
DISPLAY button
To turn on/off the setting information displayed on the upper right corner of the
screen.
MENU button
To turn the OSD menu on/off.
UP button
• To move the highlight bar up to adjust the selected item when OSD menu is on.
• To move the sub-picture up in “PIP” mode.
DOWN button
• To move the highlight bar down to adjust the selected item when OSD menu is
on.
• To move the sub-picture down in “PIP” mode.
PLUS button
• To increase the adjustment with OSD menu.
• To move the sub-picture right in “PIP” mode.
MINUS button
• To decrease the adjustment with OSD menu.
• To move the sub-picture left in “PIP” mode.
SET button
To activate the changed settings inside OSD menu.
AUTO ADJUST button
Note: For VGA input only.
To execute the Auto adjust function.
EXIT button
To turn to the previous OSD menu.
MUTE button
To turn the mute function on/off.
VOL UP button
To increase the audio output level.
VOL DOWN button
To decrease the audio output level.
User Manual BDL5530EL
2.4.2. INSERTING THE BATTERIES IN THE REMOTE CONTROL
1. Remove the cover on the rear of the remote control.
2. Insert two AAA size 1.5V batteries ensuring that the “+” and “-” ends of the
batteries are correctly aligned.
3. Replace the cover.
Note: Do not mix battery types, e.g. alkaline and manganese.
2.4.3. OPERATING RANGE OF THE REMOTE CONTROL
When pressing a remote control button, point the top of the remote control towards
the remote control sensor.
Use the remote control within a distance of about 10m/32ft from the display's remote
control sensor and within a horizontal and vertical angle of 45 degrees.
Note: The remote control may not function properly if the remote control sensor on the display
is under direct sunlight, in a location with strong illumination, or if there is an obstacle in the
path of signal transmission.
User Manual BDL5530EL
3. CONNECTIONS TO EXTERNAL EQUIPMENT
3.1. USING THE CABLE RETAINER
3.2. CONNECTING EXTERNAL EQUIPMENT (DVD/VCR/VCD)
3.2.1. USING COMPONENT VIDEO INPUT
1. Connect the green-colored (labeled as "Y") jack of the device to the green-colored "Y" jack of the display.
2. Connect the blue-colored (labeled as "Pb") jack of the device to the blue-colored "Pb" jack of the display.
3. Connect the red-colored (labeled as "Pr") jack of the device to the red-colored "Pr" jack of the display.
4. Connect the red (R) and white (L) audio jacks of the device to the AUDIO IN (AUDIO2 or AUDIO3) jacks of the
display.
DVD/VCR/VCD
User Manual BDL5530EL
3.2.2. USING S-VIDEO INPUT
1. Connect the S-Video connector of the external device to the S-VIDEO input of the display.
2. Connect the red (R) and white (L) audio jacks of the device to the AUDIO IN (AUDIO2 or AUDIO3) jacks of the
display.
DVD/VCR/VCD
3.2.3. USING VIDEO INPUT
1. Connect the Video connector of the external device to the VIDEO IN input of the display.
2. Connect the red (R) and white (L) audio jacks of the device to the AUDIO IN (AUDIO2 or AUDIO3) jacks of the
display.
DVD/VCR/VCD
User Manual BDL5530EL
3.2.4. USING HDMI INPUT
Connect the HDMI connector of the external device to the HDMI input of the display.
DVD/VCR/VCD
3.3. CONNECTING A PC
3.3.1. USING VGA INPUT
1. Connect the 15-pin VGA connector of the PC to the VGA IN connector of the display.
2. Insert the audio cable to the AUDIO IN (AUDIO1) input of the display and connect to the corresponding PC
connector.
PC
User Manual BDL5530EL
3.3.2. USING DVI INPUT
1. Connect the DVI-D connector of the PC to the DVI-D connector of the display.
2. Insert the audio cable to the AUDIO IN (AUDIO1) input of the display and connect to the corresponding PC
connector.
PC
3.3.3. USING HDMI INPUT
1. Connect the DVI-D connector of the PC to the HDMI connector of the display using a DVI-HDMI cable.
2. Insert the audio cable to the AUDIO IN (AUDIO1) input of the display and connect to the corresponding PC
connector.
PC
User Manual BDL5530EL
3.4. EXTERNAL AUDIO CONNECTION
3.4.1. CONNECTING EXTERNAL SPEAKERS
1. Connect the speaker wires to the external speaker (SPEAKERS) output of the display.
2. Turn on the unit.
Note: Make sure your display is turned off before connecting the speaker wires.
External speakers
3.4.2. CONNECTING EXTERNAL AUDIO DEVICE
Connect the red (R) and white (L) audio jacks of the external audio device to the AUDIO OUT R/L jacks of the display.
External audio device
User Manual BDL5530EL
3.5. CONNECTING ANOTHER BDL5530EL DISPLAY
You can interconnect multiple BDL5530EL units to create a daisy-chain configuration for applications such as a video
wall.
Note: The number of displays that can be used in a daisy-chain configuration will depend on the resolution of the input signal being
used.
• Connect the VGA OUT connector of the display to the VGA IN connector of additional BDL5530EL unit.
• Connect the RS-232C OUT connector of the display to the RS-232C IN connector of additional BDL5530EL unit.
• Connect the VIDEO OUT connector of the display to the VIDEO IN connector of additional BDL5530EL unit.
• Connect the AC OUT connector of the display to the AC IN connector of an external media player only.
Additional BDL5530EL display
User Manual BDL5530EL
4. OSD MENU
An overall view of the On-Screen Display (OSD) structure is shown below. This can be used as a reference for further
adjusting your display.
4.1. NAVIGATING THE OSD MENU
4.1.1. NAVIGATING THE OSD MENU USING THE REMOTE CONTROL
1. Press the MENU button on the remote control to display the OSD menu.
2. Press the UP/DOWN button to choose the item you want to adjust.
3. Press the PLUS/SET button to enter the submenu.
4. In the submenu, press the UP/DOWN button to toggle between items, or press
PLUS/MINUS button to adjust settings. If there is a submenu, press the PLUS
button to enter it.
5. Press the MINUS/EXIT button on the remote control to return to the previous
menu, or press the MENU button to exit the OSD menu.
User Manual BDL5530EL
4.1.2. NAVIGATING THE OSD MENU USING THE DISPLAY’S CONTROL BUTTONS
1. Press the MENU button to display the OSD menu.
2. Press the /button to choose the item you want to adjust.
3. Press the button to enter the submenu.
4. In the submenu, press the / button to toggle between
items, or press / button to adjust settings. If there is a
submenu, press the button to enter it.
5. Press the MENU button on the remote control to return to
the previous menu, or press the MENU button repeatedly
to exit the OSD menu.
User Manual BDL5530EL
4.2. OSD MENU OVERVIEW
4.2.1. PICTURE MENU
Brightness
Note: This function is not available when Smart contrast, Light sensor or Brightness under Panel saving is turned on.
Disable these functions to make Brightness accessible from the OSD menu.
Adjust the overall image brightness by changing the intensity of the LCD panel’s backlight.
Use the PLUS/MINUS button to adjust.
Contrast
Adjust to sharpen the picture quality. The black portions of the picture become richer and the whites
become brighter.
Use the PLUS/MINUS button to adjust.
Sharpness
Adjust to improve detail.
Use the PLUS/MINUS button to adjust.
Black level
Adjust to change the image brightness.
Use the PLUS/MINUS button to adjust.
Noise reduction
Note: For Video, S-Video, Component and HDMI inputs with interlaced video only.
Adjust to remove the noise in the image. You can select a suitable noise reduction level.
Use the UP/DOWN button to make selection.
Tint
Note: For Video, S-Video, Component, and HDMI inputs with YUV color space only. (YUV is a color space typically used
as part of a color image pipeline.)
Adjust to change the color tint of the image.
Use the PLUS/MINUS button to adjust. Press the PLUS button and the flesh tone color turns slightly
green. Press the MINUS button and the flesh tone color turns slightly purple.
Color
Note: For Video, S-Video, Component, and HDMI inputs with YUV color space only. (YUV is a color space typically used
as part of a color image pipeline.)
Adjust to increase or decrease the intensity of colors in the image.
Press the PLUS button to increase color intensity, or press the MINUS button to decrease it.
User Manual BDL5530EL
Color temperature
Select a color temperature for the image. The image has a reddish tint with a lower color temperature,
whilst a higher color temperature gives off a more bluish tint.
Use the UP/DOWN button to make selection.
Color control
Note: This function is only available when Color temperature is set to User.
With this function you can adjust the color tones of the image precisely by changing the R (Red), G (Green)
and B (Blue) settings independently.
Press the UP/DOWN button to select R, G or B, and press the PLUS/MINUS button to adjust.
Light sensor
Note: This function is not available when Smart contrast or Brightness under Panel saving is turned on. Disable these
functions to make Light sensor accessible from the OSD menu.
Choose to enable or disable the ambient light sensor. Once enabled, the image brightness will adjust
automatically as the ambient lighting conditions change.
Use the UP/DOWN button to make selection.
Smart contrast
Note: This function is not available when Light sensor or Brightness under Panel saving is turned on. Disable these
functions to make Smart contrast accessible from the OSD menu.
When turned on, this function helps enhance image contrast when displaying dark scenes.
Use the UP/DOWN button to make selection.
Smart picture
Select a smart picture mode from:
• Highbright: for moving images such as Video
• Standard: for images (factory setting)
• sRGB: for text based images
• Cinema: for movies.
• User: create your own picture settings. This mode is automatically selected after you change the settings in
the Picture menu.
Use the UP/DOWN button to make selection.
Video source
Select a video input source.
Use the UP/DOWN button to toggle between
• HDMI
• VGA
• S-Video
• DVI-D
• Component
• Video
Picture reset
Reset all settings in the Picture menu.
Use the PLUS/MINUS button to make selection. Select Reset and press the SET button to restore
settings to factory preset values. Press the EXIT button to cancel and return to the previous menu.
User Manual BDL5530EL
4.2.2. SCREEN MENU
H position
Note: For VGA input only.
Adjust the horizontal placement of the picture.
Press the PLUS button to move the image to the right, or press the MINUS button to move the image to
the left.
V position
Note: For VGA input only.
Adjust the vertical placement of the picture.
Press the PLUS button to move the image up, or press the MINUS button to move the image down.
Clock
Note: For VGA input only.
Adjust the width of the image.
Press the PLUS button to expand the width of the image, or press the MINUS button to shrink it.
Clock phase
Note: For VGA input only.
Adjust to improve the focus, clarity and stability of the image.
Use the PLUS/MINUS button to adjust.
Zoom mode
The pictures you receive may be transmitted in 16:9 format (widescreen) or 4:3 format (conventional
screen). 16:9 pictures sometimes have a black band at the top and bottom of the screen (letterbox format).
This function allows you to optimize the picture display on screen. The following zoom modes are available:
• Full - This mode restores the correct proportions of pictures transmitted in 16:9 using the
full screen display.
• Normal - The picture is reproduced in 4:3 format and a black band is displayed on either
side of the picture.
• Dynamic - Fill the entire screen by stretching 4:3 pictures non-proportionally.
• Custom - Choose to apply the custom zoom settings in the Custom zoom submenu.
Note: This mode does not support deinterlacing. The screen may flicker when displaying interlaced video.
• Real - This mode displays the image pixel-by-pixel on screen without scaling the original
image size.
User Manual BDL5530EL
• 21:9 - The picture is enlarged to 16:9 format. This mode is recommended when displaying
pictures that have black bands at the top and bottom (letterbox format).
Note: This mode does not support deinterlacing. The screen may flicker when displaying interlaced video.
Custom zoom
Note: This item is only available when Zoom mode is set to Custom.
You can use this function to further customize the zoom settings to suit the image you want to display.
Use the UP/DOWN button to toggle between the following items, and use the PLUS/MINUS button to
adjust.
• Zoom - Expands the horizontal and vertical sizes of the image simultaneously.
• H zoom - Expands the horizontal size of the image only.
• V zoom - Expands the vertical size of the image only.
• H position - Moves the horizontal position of the image left or right.
• V position - Moves the vertical position of the image up or down.
Screen reset
Reset all settings in the Screen menu.
Use the PLUS/MINUS button to make selection. Select Reset and press the SET button to restore
settings to factory preset values. Press the EXIT button to cancel and return to the previous menu.
User Manual BDL5530EL
4.2.3. AUDIO MENU
Speaker
Set the display to play audio using the built-in (internal) speaker, external speakers or external audio devices
(if connected).
Use the UP/DOWN button to toggle between
• Internal
• External
• Line-out
Volume
Adjust to increase or decrease the audio output level.
Use the PLUS/MINUS button to adjust.
Mute
To turn the mute function on/off.
Use the UP/DOWN button to make selection.
Audio source
To select the audio input source according to the source connected to the audio input and HDMI sockets on
the display.
Audio 3
Audio 1
Audio 2
HDMI
Use the UP/DOWN button to toggle between
• Audio 1
• Audio 2
• Audio 3
• HDMI
Audio reset
Reset all settings in the Audio menu.
Use the PLUS/MINUS button to make selection. Select Reset and press the SET button to restore
settings to factory preset values. Press the EXIT button to cancel and return to the previous menu.
User Manual BDL5530EL
4.2.4. PIP MENU
Notes:
• For Component, VGA, DVI-D and HDMI inputs only.
• For Full and Normal zoom modes only.
• The PIP function is turned off by default. Press the PIP ON/OFF button on the remote control to turn on PIP and make it accessible
from the OSD menu.
PIP
To turn PIP mode on/off.
Use the UP/DOWN button to make selection.
PIP input
Select the input signal for the sub-picture.
Use the UP/DOWN button to make selection.
PIP change
To exchange between the main picture and sub picture.
Use the PLUS/MINUS button to make selection. Select Reset and press the SET button to restore
settings to factory preset values. Press the EXIT button to cancel and return to the previous menu.
PIP size
Select the size of the sub picture in the PIP mode.
Use the UP/DOWN button to toggle between
• Large
• Middle
• Small
PIP audio
Select the audio source in the PIP mode.
Use the UP/DOWN button to toggle between
• Main - Select audio from the main picture
• Sub - Select audio from the sub picture.
PIP reset
Reset all settings in the PIP menu.
Use the PLUS/MINUS button to make selection. Select Reset and press the SET button to restore
settings to factory preset values. Press the EXIT button to cancel and return to the previous menu.
User Manual BDL5530EL
Notes:
• The PIP function is only available under certain signal source combinations as shown in the table below.
Main picture signal source
Component VGA
Video
S-Video
DVI-D
HDMI
Video
S-Video
Component
VGA
Sub
picture
signal
source
DVI-D
HDMI
( : PIP function available, : PIP function unavailable)
• The availability of the PIP function will also depend on the resolution of the input signal being used.
User Manual BDL5530EL
4.2.5. CONFIGURATION 1 MENU
Switch on state
Set the display to turn on or remain off when the power cord is connected to a wall outlet.
Use the UP/DOWN button to toggle between
• Last status - The display will return to the previous power status (on/off/standby) when removing and
replacing the power cord.
• Forced on - The display will turn on when the power cord is connected to a wall outlet.
• Power off - The display will remain off when the power cord is connected to a wall outlet.
Auto adjust
Note: For VGA input only.
Use this function to automatically optimize the display of the VGA image. Press the SET button to adjust.
Power save
Set the display to reduce the power automatically.
Use the UP/DOWN button to toggle between
• RGB - Select On to let the display enter DPMS (Display Power Management Signaling) mode when no
signal can be detected from the HDMI, DVI-D, and VGA inputs after three successive cycles. Use the
PLUS/MINUS button to make selection.
• Video - Select On to let the display enter power saving mode when no signal is detected from the Video,
S-Video, and Component inputs after three successive cycles. Use the PLUS/MINUS button to make
your selection.
Language
Select the language for the OSD menu.
Use the UP/DOWN button to select a language.
Panel saving
Choose to enable the panel saving functions to reduce the risk of the "image persistence”. Use the PLUS/
MINUS button to toggle between
• Brightness - Select On and the brightness of the image will be reduced to an appropriate level, and the
Brightness setting in the Picture menu will become unavailable. Use the PLUS/MINUS button to make
selection.
• Pixel shift - Select the time interval for the display to slightly expand the image size and shift the pixel
position in four directions (up, down, left, and right). Use the PLUS/MINUS button to make selection
(Off-900 seconds from current time). This helps to alleviate the issues of ghost imaging.
IMPORTANT: It is not recommended to keep a single static image displayed on your unit for long periods
of time. This can cause image sticking, or ghost images, which will decrease the quality of your images. In
User Manual BDL5530EL
some instances, ghost image damage can be permanent. To avoid such issues, we strongly recommend one of
the following actions:
• Change the picture periodically
• Use a screen saver with changing images
Color system
Note: For Video and S-Video inputs only.
Select the color system depending on the input video format.
Use the UP/DOWN button to make selection.
• Auto
• PAL 3.58
• NTSC 4.43
• PAL 4.43
• SECAM
• NTSC 3.58
MEMC effect
To turn the Motion Estimation, Motion Compensation (MEMC) effect on/off.
Use the UP/DOWN button to make selection.
Configuration reset
Reset all settings in the Configuration 1 menu.
Use the PLUS/MINUS button to make selection. Select Reset and press the SET button to restore
settings to factory preset values. Press the EXIT button to cancel and return to the previous menu.
Factory reset
Reset all settings in the Picture, Screen, Audio, PIP, Configuration 1, Configuration 2, and
Advanced option menus. Use the PLUS/MINUS button to make selection. Select Reset and press the
SET button to restore settings to factory preset values. Press the EXIT button to cancel and return to the
previous menu.
User Manual BDL5530EL
4.2.6. CONFIGURATION 2 MENU
OSD turn off
Set the period of time the OSD menu stays on the screen (from 5 to 120 seconds)
Use the PLUS/MINUS button to adjust.
OSD mode
Select the orientation of the OSD according to the orientation the display is installed.
Use the UP/DOWN button to toggle between
• Portrait
• Landscape
Information OSD
Set the period of time the information OSD stays on the screen. The information OSD will display when
input signal is changed.
Use the UP/DOWN button to adjust. The information OSD will not appear when Off is selected. If 0 is
selected, the information OSD will remain on the screen.
Sleep timer
Set the display to turn itself off to standby mode within a user-specified amount of time. (Off-24 hours from
current time)
Use the UP/DOWN button to adjust.
Note: When the Sleep timer is activated, Schedule settings will be disabled.
OSD H position
Adjust the horizontal position of the OSD menu.
Use the UP/DOWN button to adjust.
OSD V position
Adjust the vertical position of the OSD menu.
Use the UP/DOWN button to adjust.
Monitor information
Shows the information about your display, including model name, serial number, operating hours and
software version.
Press the PLUS button to view the information. Press the EXIT button to return to the previous menu.
User Manual BDL5530EL
4.2.7. ADVANCED MENU
Input resolution
Note: For VGA input only.
Set the resolution of the VGA input. This is only required when the display is unable to detect the VGA input
resolution correctly.
Use the UP/DOWN button to toggle between
• Auto
• 1024x768
• 1280x768
• 1360x768
• 1366x768
Black level expansion
Note: For Video, S-Video, Component, and HDMI (video mode) inputs only.
This feature offers deeper blacks for an even better image quality. Select a suitable black level expansion
setting to reveal more details in the dark parts of an image.
Use the UP/DOWN button to toggle between
• Off
• Low
• Middle
• High
Gamma selection
Gamma is what controls the overall brightness of an image. Images which are not corrected properly can
appear too white or too dark, so controlling the gamma properly can have a huge influence on the overall
picture quality of your display.
Select a display gamma value to best suit the image and optimize image brightness and contrast.
Use the UP/DOWN button to toggle between
• 2.2
• 2.4
• Native
Scan mode
Note: For Video, S-Video, Component, and HDMI (video mode) inputs only.
Change the display area of the image.
Use the UP/DOWN button to toggle between
• Over scan - Displays about 95% of the original size of the image. The rest of the areas surrounding the
image will be cut off.
• Under scan - Displays the image in its original size.
Scan conversion
Note: For Video, S-Video, Component, and HDMI (video mode) inputs only.
Choose to enable or disable the IP (Interlace to Progressive) conversion function.
Use the UP/DOWN button to toggle between
User Manual BDL5530EL
• Progressive - Enable the IP conversion function (recommended). Once enabled, the interlace input signal
will be converted to progressive format for better display quality.
• Interlace: Disable the IP function. This mode is suitable for displaying motion pictures, but increases the
chance of image retention.
Film mode
Note: For Video, S-Video, Component, and HDMI (video mode) inputs only.
Choose to turn on or off the film mode frame conversion function.
Use the UP/DOWN button to toggle between
• Auto - Enable the film mode frame conversion function for movies and motion pictures. The display
converts a 24 frames-per-second (24 fps) input signal format to DVD video signal format. Once this
function is enabled, it is recommended that you set the Scan conversion function to Progressive.
• Off - Disable the film mode frame conversion function. This mode is suitable for TV broadcasting and VCR
signals.
IR control
Select the operation mode of the remote control when multiple BDL5530EL units are connected via RS232C
cables.
Use the UP/DOWN button to toggle between
• Normal - All units can be operated normally by the remote control.
• Primary - Designate this display as the primary unit for remote control operation. Only this display will be
operated by the remote control.
• Secondary - Designate this display as the secondary unit. This display can not be operated by the remote
control, and will only receive the control signal from the primary unit via the RS232C connection.
• Lock - Lock the remote control function of this display. To unlock, press and hold the DISPLAY button
on the remote control for 5 seconds.
Keyboard control
Choose to enable or disable the function of the keyboard (control buttons) on the display.
Use the UP/DOWN button to toggle between
• Lock - Disable the keyboard.
• Unlock - Enable the keyboard.
Tiling
Notes:
• For VGA input only.
• This function is not available when PIP is turned on. Disable PIP to make Tiling accessible from the OSD menu.
With this function you can create a single large screen matrix (display wall) that consists of up to 25
BDL5530EL displays (5 units on the vertical side and 5 units on the horizontal side). This requires you to
connect each BDL5530EL unit in a daisy-chain configuration.
User Manual BDL5530EL
Example:
2 x 2 screen matrix (4 displays)
5 x 5 screen matrix (25 displays)
H monitors = 5
H monitors = 2
V monitors = 2
V monitors = 5
H monitors
H monitors
Position
Position
• H monitors - Select the number of displays on the horizontal side.
• V monitors - Select the number of displays on the vertical side.
• Position - Select the position of this display in the screen matrix. Position is defined by the total number of
displays in the video wall counting from the top, left hand display and counting horizontally. The number is
then continued on the next row down, and the procedure is continued until the final display is reached. See
examples above for further explanation.
• Frame comp. - Choose to turn frame compensation on or off. If turned on, the display will adjust the
image to compensate for the width of the bezels in order to accurately display the image.
Frame comp. - Off
Frame comp. - On
• Enable: Choose to enable or disable the Tiling function. If enabled, the display will apply the settings in H
monitors, V monitors, Position, and Frame comp..
Note: PIP function is disabled when Tiling is enabled.
• Switch on delay: Choose to enable or disable a sequence in turning on the screen matrix. If enabled, the
display will turn on one horizontal matrix at a time starting from the top row.
Heat status
This function allows you to check the thermal status of the display at any time. The accuracy of the
_
+
temperature indicated is 5 degrees Celsius.
Press the PLUS button to view the heat status. Press the EXIT button to return to the previous menu.
Date and time
Adjusts current date and time for the display’s internal clock.
Press the UP/DOWN button to toggle between the Year, Month, Day, Hour, Minute, and Daylight
saving time settings, and then press the PLUS/MINUS button to adjust.
Schedule
Note: We recommend setting up current date and time in Date and time before using the Schedule function.
User Manual BDL5530EL
This function allows you to program up to seven different scheduled time intervals for the display. You can
select the time the unit turns on and turns off, the days in a week it is activated, and which input source the
display will use for each scheduled activation period.
For example, if you wish to turn the display on automatically at 7:30 AM and off at 10:30 PM on Tuesdays and
Wednesdays and display the signal from the HDMI input:
Time
0:001:00 2:00 3:00 4:00 5:00 6:00 7:00 8:00 9:00 10:00 11:0012:0013:0014:0015:0016:0017:0018:0019:0020:0021:0022:0023:00
MON
Off
TUE
WED
Off
Off
On
On
Off
Off
Day THU
FRI
Off
Off
Off
Off
SAT
SUN
Perform the following steps:
1. With the Schedule item highlighted in the Advanced option menu, press the PLUS button to open
the submenu.
2. Press the UP/DOWN button to select schedule item #1 ( 1), and then press the SET button. A check
mark will appear in the box indicating that the schedule item has been selected.
3. With the On item highlighted, press the SET button and then press the UP/DOWN button to set the
power on hour to “07”.
4. Press the PLUS button to move to the minute slot. Press the UP/DOWN button to set the power on
minute to “30”, then press the EXIT button.
5. Press the PLUS button to highlight the Off item. Press the SET button, and then press the UP/DOWN
button to set the power off hour to “22”.
6. Press the PLUS button to move to the minute slot. Press the UP/DOWN button to set the power off
minute to “30”, then press the EXIT button.
7. Press the PLUS button to highlight the Input item, and then press the UP/DOWN button to select
HDMI.
8. Press the PLUS button to select Tue and then press the SET button. A check mark will appear in the
box indicating that it has been selected.
9. Press the PLUS button to select Wed and then press the SET button. A check mark will appear in the
box indicating that it has been selected.
User Manual BDL5530EL
10. Now you have completed the schedule settings. The on-screen display should look like the illustration
below:
11. Press the EXIT button and the menu will close and the schedule settings will take effect.
To set up more schedule items, repeat the steps above except that a different schedule item should be
selected (schedule item #2 ( 2) through #7 ( 7)) in step 2.
Notes:
• Seven scheduling options are available so that you can choose between different video input modes for different
schedules during the week. For example, VGA input on a Monday, HDMI on Tuesday to Friday, S-Video for
weekends.
• If you do not want to use a power on time, select "--" for the power on hour slot, and "00" for the minute slot. The
display will only turn off at the time you set.
• If you do not want to use a power off time, select "--" for the power off hour slot, and "00" for the minute slot. The
display will only turn on at the time you set.
• If no input source is selected, the default input source (Video) will be used.
• If Every day is selected, the display will turn on everyday regardless of other day settings (e.g Mon, Tue, Wed..., etc.).
• Should schedule periods overlap, the power on time has priority over power off time. For example, if schedule item
#1 sets the display to power on at 10:00 AM and off at 5:00 PM, and schedule item #2 sets the display to power
on at 4:00 PM and off at 9:00 PM on the same day, then the display will power on at 10:00 AM and off at 9:00
PM.
• If there are multiple schedule items programmed for the same time period, then the highest numbered schedule item
has priority. For example, if schedule items #1 and #2 both set the display to power on at 7:00 AM and off at 5:00
PM, then only schedule item # 1 will take effect.
Monitor ID
Set the ID number for controlling the unit via the RS232C connection. Each display must have a unique ID
number when multiple BDL5530EL units are connected.
See table under "Tiling" for more information. Use the PLUS/MINUS button to select an ID.
DDC/CI
Choose to turn On or Off the DDC/CI communication function. Select ON for normal use.
Use the UP/DOWN button to make selection.
Smart power
Set the display to reduce the power consumption automatically. Setting to High will bring the most power
savings.
Use the UP/DOWN button to toggle between
• Off
• Medium
• High
Auto signal detection
Select to let the unit detect and display available signal source automatically.
• On - Set the unit to display the image automatically once a signal is connected.
User Manual BDL5530EL
• Off - Once a signal is connected, it can only be selected manually.
Use the UP/DOWN button to make selection.
Advanced option reset
Reset all settings in the Advanced option menu.
Press the PLUS button to open the submenu, and then press the PLUS/MINUS button to make selection.
Select Reset and press the SET button to restore settings to factory preset values. Press the EXIT button
to cancel and return to the previous menu.
User Manual BDL5530EL
5. INPUT MODE
VGA Resolution
Active Resolution
Standard
Resolution
Refresh Rate
Pixel Rate
Aspect Ratio
4:3
Stand for Mode
H Pixels
640
V Lines
60 Hz
72 Hz
75 Hz
25.175 MHz
31.5 MHz
31.5 MHz
VGA
480
Video Graphic Array
Wide Video Graphic
Array
WVGA
SVGA
720
800
400
600
70 Hz
33.75 MHz
16:9
4:3
60 Hz
75 Hz
60 Hz
75 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
40 MHz
49.5 MHz
65 MHz
Super VGA
XGA
1024
768
4:3
Extended Graphic Array
78.75 MHz
79.5 MHz
79.5 MHz
108 MHz
108 MHz
85.5 MHz
85.5 MHz
162 MHz
148.5 MHz
WXGA
WXGA
SXGA
1280
1280
1280
1280
1360
1366
1600
1920
768
800
5:3
16:10
4:3
Wide XGA
Wide XGA
Super XGA
Super XGA
Wide XGA
Wide XGA
Ultra XGA
HD1080
960
SXGA
1024
768
5:4
WXGA
WXGA
UXGA
HD1080
16:9
16:9
4:3
768
1200
1080
16:9
SDTV Resolution
Active Resolution
Standard
Resolution
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
H Pixels
V Lines
480i
29.97 Hz
59.94 Hz
25 Hz
13.5 MHz
27 MHz
720
480
4:3
4:3
Modified NTSC Standard
Modified PAL Standard
480p
576i
13.5 MHz
27 MHz
720
480
576p
50 Hz
HDTV Resolution
Active Resolution
Standard
Resolution
Refresh Rate
Pixel Rate
74.25 MHz
74.25 MHz
148.5 MHz
Aspect Ratio
16:9
Stand for Mode
H Pixels
V Lines
50 Hz
60 Hz
25 Hz
30 Hz
50 Hz
60 Hz
720p
1280
720
Normally DVB Mode
Normally ATSC Mode
Normally ATSC Mode
1080i
1920
1920
1080
1080
16:9
1080p
16:9
• PC text quality is optimum in HD 1080 mode (1920 x 1080, 60Hz).
• Your PC monitor may appear differently depending on the manufacturer (and your particular version of Windows).
Check your PC instruction book for information about connecting your PC to a display.
User Manual BDL5530EL
• If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5KHz (horizontal). In some
cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is
disconnected). If this happens, press the INPUT button to enter the video mode. Also, make sure that the PC is
connected.
• If horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable connections.
• The display settings table complies with IBM/VESA standards, and based on analog input.
User Manual BDL5530EL
6. PIXEL DEFECT POLICY
We strive to deliver the highest quality products and use some of the industry's most advanced manufacturing processes
whilst practicing stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- &
LCD- displays are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects,
but Philips guarantees that any LCD display with an unacceptable number of defects will be repaired during the warranty
period in line with your local guarantee conditions.
This notice explains the different types of pixel defects and defines the acceptable defect level for the BDL5530EL LCD
screen. In order to qualify for repair under warranty, the number of pixel defects must exceed a certain level as shown in
the reference table. If the LCD screen is within specification a warranty exchange / claim back will be refused.
Additionally, because some types or combinations of pixel defects are more noticeable than others, Philips sets even
higher quality standards for those.
6.1. PIXELS AND SUB-PIXELS
A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and blue. Many pixels
together form an image. When all sub-pixels of a pixel are lit, the three colored sub-pixels together appear as a single
white pixel. When all are dark, the three colored sub-pixels together appear as a single black pixel. Other combinations
of lit and dark sub-pixels appear as single pixels of other colors.
subpixel
subpixel
subpixel
pixel
6.2. TYPES OF PIXEL DEFECTS + DOT DEFINITION
Pixel and sub-pixel defects appear on the screen in different ways. There are three categories of pixel defects and several
types of sub-pixel defects within each category.
Dot definition = What is a defective "Dot"? :
One or more defective, adjacent sub-pixel is defined as one "dot". The number of defective sub-pixels is not relevant to
define a defective dot. This means that a defective dot can consist of one, two or three defective sub-pixels which can be
dark or lit.
One dot = One Pixel; consists of three sub-pixels of Red; Green and Blue
6.3. BRIGHT DOT DEFECTS
Bright dot defects appear as pixels or sub-pixels that are always lit or "on". These are the examples of bright dot defects:
Two adjacent lit sub-pixels:
- Red + Blue = Purple
- Red + Green = Yellow
Three adjacent lit sub-pixels (one
white dot)
One lit red, green or blue sub-pixel
- Green + Blue = Cyan (Light Blue)
6.4. DARK DOT DEFECTS
Black dot defects appear as pixels or sub-pixels that are always dark or "off". These are the examples of black dot
defects:
Two dark dots, specifications define
Two adjacent dark dots = 1 pair of
dark dots
One dark dot
the minimum distance between dark
dots
6.5. PROXIMITY OF PIXEL DEFECTS
Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also
specifies tolerances for the proximity of pixel defects. In the table below you can find specifications about:
• Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots)
• Minimum distance between dark dots
• Total no. of all defective dots
6.6. PIXEL DEFECT TOLERANCES
In order to qualify for repair due to pixel defects during the warranty period, a PDP/TFT panel in a Philips LCD display
must have pixel or sub-pixel defects exceeding the tolerances listed in the following table.
BRIGHT DOT EFFECT
MODEL
1 lit sub pixel
ACCEPTABLE LEVEL
BDL5530EL
0
BLACK DOT EFFECT
1 dark sub pixel
ACCEPTABLE LEVEL
8
TOTAL DOT DEFECTS OF ALL TYPES
Note: * 1 or 2 adjacent sub pixel defects = 1 dot defect
8
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL5530EL
7. CLEANING AND TROUBLESHOOTING
7.1. CLEANING
Caution When Using the Display
• Do not place your hands, face or objects close to the ventilation holes of the
display. The top of the display is usually very hot due to the high temperature of
air being expelled through the ventilation holes. Burns or personal injuries may
occur if any body parts are brought too close. Placing any object near the top
of the display could also result in heat related damage to the object as well as
the display itself.
• Be sure to disconnect all cables before moving the display. Moving the display
with its cables attached may damage the cables and thus cause fire or electric
shock.
• Disconnect the power plug from the wall outlet as a safety precaution before
carrying out any type of cleaning or maintenance procedure.
Front Panel Cleaning Instructions
• The front of the display has been specially treated. Wipe the surface gently
using only a cleaning cloth or a soft, lint-free cloth.
• If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent
solution. Wring the cloth to remove excess liquid. Wipe the surface of the
display to remove dirt. Then use a dry cloth of the same type to dry.
• Do not scratch or hit the surface of the panel with fingers or hard objects of
any kind.
• Do not use volatile substances such as sprays, solvents and thinners.
Cabinet Cleaning Instructions
• If the cabinet becomes dirty, wipe with a soft, dry cloth.
• If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent
solution. Wring the cloth to remove as much moisture as possible. Wipe the
cabinet. Use another dry cloth to wipe over until the surface is dry.
• Do not allow any water or detergent to come into contact with the surface of
the display. If water or moisture gets inside the unit, operating problems, or
electrical and shock hazards may result.
• Do not scratch or hit the cabinet with fingers or hard objects of any kind.
• Do not use volatile substances such as sprays, solvents and thinners on the
cabinet.
• Do not place anything made from rubber or PVC near the cabinet for any
extended periods of time.
User Manual BDL5530EL
7.2. TROUBLESHOOTING
Symptom
Possible Cause
Remedy
No picture is displayed
1. The power cord is disconnected.
1. Plug in the power cord.
2. The main power switch on the back of 2. Make sure the power switch is switched on.
the display is not switched on.
3. Connect a signal connection to the display.
3. The selected input has no connection.
4. The display is in standby mode with
VGA.
Interference displayed on
the display or audible noise appliances, traffic or fluorescent lights.
is heard
Caused by surrounding electrical
Move the display to another location to see if
the interference is reduced.
Color is abnormal
The signal cable is not connected properly. Make sure that the signal cable is attached
firmly to the back of the display.
Picture is distorted with
abnormal patterns
1. The signal cable is not connected
properly.
1. Make sure that the signal cable is attached
firmly.
2. The input signal is beyond the
capabilities of the display.
2. Check the video signal source to see if it is
beyond the range of the display. Please
verify its specifications with this display’s
specification section.
Display image doesn’t fill up The zoom mode is not correctly set.
the full size of the screen
Use the Zoom mode or Custom zoom
function in the Screen menu to fine-tune
display geometry and time frequency
parameter.
Can hear sound, but no
picture
Improperly connected source signal cable. Make sure that both video inputs and sound
inputs are correctly connected.
Can see picture but no
sound is heard
1. Improperly connected source signal
cable.
1. Make sure that both video and sound inputs
are correctly connected.
2. Volume is turned all the way down.
3. Mute is turned on.
2. Use VOL UP/VOL DOWN button to
hear sound.
3. Switch Mute off by using the MUTE
4. No external speaker connected.
button.
4. Connect external speakers and adjust the
volume to a suitable level.
Some picture elements do Some pixels of the display may not turn on. This display is manufactured using an
not light up
extremely high level of precision technology:
however, sometimes some pixels of the display
may not display. This is not a malfunction.
After-Images can still be
seen on the screen after the extended period of time
display is powered off.
(Examples of still pictures
include logos, video games,
computer images, and
A still picture is displayed for an over
Do not allow a still image to be displayed for
an extended period of time as this can cause a
permanent after-image to remain on the
MENU for further details.
images displayed in 4:3
normal mode)
User Manual BDL5530EL
8. TECHNICAL SPECIFICATIONS
Display
Item
Specifications
Screen size (Active Area)
Aspect ratio
54.6” (138.68 cm) LCD
16:9
Number of pixels
Pixel pitch
Displayable colors
Brightness
1920 (H) x 1080 (V)
0.21 (H) x 0.63 (V) [mm]
1073.7M colors
2
400 cd/m
Smart contrast
Contrast ratio (typical)
Viewing angle
19500:1
4000:1
178 degrees
In/Out Terminals
Item
Specifications
12W (L) + 12W (R) [RMS]/8
Speaker Output
Internal Speaker
1 Way 1 Speaker System
82 dB/W/M/160 Hz ~ 13 KHz
0.5V [rms] (Normal)/ 2 Channel (L+R)
0.5V [rms] (Normal)/ 2 Channel (L+R)
Audio Output
Audio Input
RS232C
RCA Jack x 1
RCA Jack x 2
D-Sub Jack x 2 (9 pin) TXD + RXD (1:1)
Digital RGB: TMDS (Video + Audio)
HDMI Input
DVI-D Input
HDMI Jack x 1 (Type A) MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Audio - 48 KHz/ 2 Channel (L+R)
DVI-D jack x 1
Digital RGB: TMDS (Video)
Analog RGB: 0.7V [p-p] (75 ), H/CS/V: TTL (2.2k ), SOG: 1V [p-p]
(75 )
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Audio: 0.5V [rms] (Normal)/2 Channel (L+R)
Analog RGB: 0.7V [p-p] (75 ), H/CS/V: TTL (2.2k ), SOG: 1V [p-p]
(75 )
D-Sub Jack x 1 (15 pin)
3.5mm Mini-jack x 1
D-Sub Jack x 1 (15 pin)
RGB Input
RGB Output
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Y: 1V [p-p] (75 ), Pb: 0.7V [p-p] (75 ), Pr: 0.7V [p-p] (75 )
MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
Y: 1V [p-p] (75 ), C: 0.286V [p-p] (75 ) [NTSC]
Y: 1V [p-p] (75 ), C: 0.300V [p-p] (75 ) [PAL/SECAM]
Video: 1V [p-p] (75 ) [NTSC/PAL/SECAM]
Component Input
S-Video Input
RCA Jack x 1
Mini DIN Jack x 1 (4 pin)
Video Input
Video Output
BNC Jack x 1
BNC Jack x 1
Video: 1V [p-p] (75 ) [NTSC/PAL/SECAM]
General
Item
Specifications
AC 100V ~ 240V, 50/60 Hz
175W
Power Supply
Power Consumption (Max)
User Manual BDL5530EL
Dimension [W x H x D mm]
With Stand
Without Stand
Weight
1530 x 778 x 405 mm
1530 x 732 x 59 mm
With Stand
31 Kg
29 Kg
Without Stand
Environmental Condition
Item
Specifications
Operational
Storage
Operational
Storage
0 ~ 40 C
-20 ~ 60 C
20 ~ 80% RH (No condensation)
5 ~ 95% RH (No condensation)
Temperature
Humidity
Operational
Storage / Shipment
800 ~ 1100 hPa (Altitude: 0 ~ 4,000 m)
700 ~ 1100 hPa (Altitude: 0 ~ 15,000 m)
Pressure
Internal Speaker
Item
Specifications
Type
Input
Impedance
1 Way 1 Speaker
12 W (RMS)
8
Output Sound Pressure
Frequency Response
82 dB/W/M
160 Hz ~ 13 KHz
User Manual BDL5530EL
|