Philips Flat Panel Television BDL5231V User Manual

Public Signage

Solutions

User Manual

TYPE NR.

BDL5231V

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

SAFETY INSTRUCTIONS

WARNINGS AND PRECAUTIONS

KNOW THESE SAFETY SYMBOLS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any

inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included

with this product.

Note to CATV system installer: This reminder is provided to call CATV system installer’s attention to Article

820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as

practical.

Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user’s authority to

operate it.

Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.

Attention: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la bome correspondante

de la prise et pousser jusqu’au fond.

Important: One Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement

of U.S. copyright laws. Certain Canadian programs may also be copyrighted and any unauthorized recording in whole

or in part may be in violation of these rights.

TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

The Socket-outlet shall be installed near the apparatus and shall be easily accessible.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

REGULATORY INFORMATION

CE DECLARATION OF CONFORMITY

Philips Consumer Electronics declare under our responsibility that the product is in conformity with the following standards

• EN60950-1:2001 (Safety requirement of Information Technology Equipment)

• EN55022:2006 (Radio Disturbance requirement of Information Technology Equipment)

• EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment)

•EN6100-3-2:2000+A2:2006 (Limits for Harmonic Current Emission)

• EN6100-3-3:1995+A1:2001+A2:2005 (Limitation of Voltage Fluctuation and Flicker)

following provisions of directives applicable

• 73/23/EEC (Low Voltage Directive)

• 2004/108/EC (EMC Directive)

• 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on

ISO9000 level.

FEDERAL COMMUNICATIONS COMMISSION (FCC) NOTICE (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated

In a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.

To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING

EQUIPMENT REGULATIONS.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE

The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works

together (computer, monitor, printer, and so on) should have the same power supply source.

The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with

a nominal value no larger than 16 amperes (A).

To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be

located near the equipment and easily accessible.

A protection mark “B” confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-

42107 and PN-89/E-06251.

ELECTRIC, MAGNETIC AND ELECTRONMAGNETIC FIELDS (“EMF”)

1. Philips Royal Electronics manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general

have the ability to emit and receive electromagnetic signals.

2. One of Philips’ leading Business Principles is to take all necessary health and safety measures for our products, to comply with all

applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products.

3. Philips is committed to develop, produce and market products that cause no adverse health effects.

4. Philips confirms that if its products are handled properly for their intended use, they are safe to use according to scientific evidence

available today.

5. Philips plays an active role in the development of international EMF and safety standards, enabling Philips to anticipate further developments

in standardization for early integration in its products.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

INFORMATION FOR UK ONLY

WARNING - THIS APPLIANCE MUST BE EARTHED.

Important:

This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this

type of plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.

3. Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an

appropriate 3-pin plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug

without a fuse is used, the fuse at the distribution board should not be greater

than 5A.

Note: The severed plug must be destroyed to avoid a possible shock hazard should it

be inserted into a 13A socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured in accordance with the following code:

BLUE - “NEUTRAL” (“N”)

BROWN - “LIVE” (“L”)

GREEN & YELLOW - “EARTH” (“E”)

1. The GREEN AND YELLOW wire must be connected to the terminal in

the plug which is marked with the letter “E” or by the Earth symbol or

coloured GREEN or GREEN AND YELLOW.

2. The BLUE wire must be connected to the terminal which is marked with the letter

“N” or coloured BLACK.

3. The BROWN wire must be connected to the terminal which marked with the letter

“L” or coloured RED.

Before replacing the plug cover, make certain that the cord grip is clamped over the

sheath of the lead - not simply over the three wires.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

中国电子信息产品污染控制标识要求 (中国RoHS法规标示要求)

产品中有毒有害物质或元素的名称及含量

有毒有害物质或元素

汞镉六价铬多溴联苯多溴二苯醚

（Pb）（Hg）（Cd）（Cr 6+）（PBB）（PBDE）

部件名称

铅

外壳

○

○ ○

○

× ×

○

○ ○

液晶面板

电路板组件

附件

(遥控器，电源线，连接线)

遥控器电池

○ ○

○

○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006

标准规定的限量要求以下 ◦

×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出

SJ/T11363-2006 标准规定的限量要求 ◦

环保使用期限

此标识指期限(十年)，电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外

泄或突变，电子信息产品用户使用该电子信息产品不会对环境造成严重污染或对其人身、财产造

成严重损害的期限。

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

NORTH EUROPE (NORDIC COUNTRIES) INFORMATION

Placering/Ventilation

VARNING:

FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.

Placering/Ventilation

ADVARSEL:

SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.

Paikka/Ilmankierto

VAROITUS:

SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.

Plassering/Ventilasjon

ADVARSEL:

NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.

END-OF-LIFE DISPOSAL

Your new TV/Monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the

amount of reusable materials and to minimize the amount to be disposed of.

Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer.

(For customers in Canada and U.S.A.)

This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on

recycling contact www.eia.org (Consumer Education Initiative)

WASTE ELECTRICAL AND ELECTRONIE EQUIPMENT-WEEE

Attention users in European Union private households

This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EG

governing used electrical and electronic appliances, this product may not be disposed of with normal

household waste. You are responsible for disposal of this equipment through a designated waste electrical

and electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic, contact your local

government office, the waste disposal organization that serves your household or the store at

which you purchased the product.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Contents

The BDL5231V monitor pack* should include:

•

Main switch cover

Screw for Main Switch cover

BNC TO RCA adapter x 5

Logo guider

•

LCD monitor

Power cord (1.8 m)

VGA Signal Cable (1.8 m)

User Manual

Clamper

Remote Control and AAA Batteries

Screw for Clamper

Cable belt

(For tightening cables)

Xxxxxxxxxxxxxx

xxxxxxxxxxxxxx

xxxxx

BNC TO RCA adapter x 5

User’ Manual

Screw for Main switch cover

(M3 6)

Screw for Clamper

(M4 x 8) x 2

Main switch cover

The supplied power cor varies depending on destination.

Cable belt

(For tightening the power cor

and VGA / HDMI cable)

For North

America

For EU

For China

Power cor

Remote Control and AAA

Batteries

Please make sure that for all other regions, apply a power cord that conforms

to the AC voltage of the power socket and has been approved by and complies

with the safety regulations of the particular country

Clamper

You might like to save the package box and packing material for shipping

the monitor

The following components are prepared as options.

•

External Speakers

Table stand

Logo guider

Video Signal Cable

(D-SUB to D-SUB Cable)

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Connection & Button Overviews

Control Panel

POWER button ( ) :To switch the power on/off.

MUTE button : To switch the audio mute ON/OFF.

INPUT button :To set the function while OSD menu is on or to activate input selection menu while OSD menu is off

PLUS (+) button :To increase the adjustment while OSD menu is on, or to increase the audio output level while the OSD menu is off.

MINUS (-) button :To decrease the adjustment while OSD menu is on, or to decrease the audio output level while the OSD menu is off.

UP (S) button : To move the highlight bar up to adjust the selected item while OSD menu is on, or to activate the OSD menu when the OSD

menu is off.

DOWN (T) button :To move the highlight bar down to adjust the selected item while OSD menu is on, or to activate the OSD menu when

the OSD menu is off.

MENU button :To return to previous menu while OSD menu is on or to activate the OSD menu when the OSD menu is off.

Remote control sensor, Power indicator and ambient light sensor : To receive the IR signal from the remote control. The

indicator would show green when the LCD monitor is active and would turn red when the LCD is POWER OFF. While in the case of the system is in

power save mode, it would show both green and red. When SCHEDULE is enabled, it would blink green and glow red. If the indicator blinks red , it

tells that a failure is detected. The image brightness will be auto adjusted when “LIGHT SENSOR” set to “ON” on OSD menu.

Main Power Switch : To turn the main power on/off.

NOTE: Keyboard Control Lock Mode This function completely disables the access to all Keyboard Control functions. To enable the

keyboard control lock, press both of “S” and “T” buttons and hold down continuously for more than 3 seconds. To recover back to the user mode,

press both of “S” and “T” and hold continuously for three 3 seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Terminal Panel

EXTERNAL CONTROL (mini D-Sub 9 pin)

This is for serial connection when multiple BDL5231V monitors are connected. To achieve remote management through RS232 commands (refer to the

RS232 remote control user manual), connect the RS-232C OUT connector from a computer or from a different BDL5231V monitor to the RS-232C

IN connector from your BDL5231V monitor. The same RS-232C commands can be looped through by connecting the RS-232C OUT of this monitor to

the next RS-232C IN.

AUDIO IN 1, 2, 3

To input audio signal from external equipment such as a computer,VCR or DVD player.

AUDIO OUT

To output the audio signal from the AUDIO IN 1,2 and 3 jack or HDMI.

EXTERNAL SPEAKERTERMINAL

To output the audio signal to external speakers from AUDIO IN 1, 2, 3 jack or HDMI.

AC IN connector

To connect with the supplied power cord.

HDMI IN

To input digital video/audio signals from a digital equipment or computer.

DVI-D IN

To input digital video signals from a digital equipment or computer.

PC-A IN (mini D-Sub 15 pin)

To input analog RGB signals from a computer or other RGB equipment.

RGB OUT (mini D-Sub 15 pin)

To output the signal from PC-A IN.

CVI IN [Y, Pb/Cb, Pr/Cr] (BNC)

To connect an equipment such as a DVD player, HDTV device, or Laser disc player.

VIDEO IN/OUT

VIDEO IN connector (BNC and RCA): To input a composite video signal. Note that BNC and RCA are not available at the same time.

VIDEO OUT connector (BNC): To output the composite video signal fromVIDEO IN connector.

S-VIDEO IN connector (MINI DIN 4 pin): To input the S-video (Y/C separate signal).

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Remote Control

SET button

To activate the setting with OSD menu.

AUTO ADJUST button

execute the AUTO ADJUST function.

MUTE button

To turn the mute function on/off.

VIDEO SOURCE button

To activate input selection menu, and push “S” or “T” to select input

source from [HDMI], [DVI-D], [PC-A], [CVI], [VIDEO(S)] and [AV], and

then push “SET” to switch to selected input source.

AUDIO SOURCE button

To activate audio selection menu, and push “S” or “T” to select audio

source from [AUDIO1] [AUDIO2], [AUDIO3] and [HDMI], and then push

“SET” to switch to selected audio source.

SIZE button

To select the pictur

size from [FULL], [NORMAL], [CUSTOM] , [DYNAM

IC] and [REAL].

BRIGHTNESS button

To start the BRIGHTNESS OSD selection, and then push "+" or "-"

button to adjust the value.

POWER button

UP button

To turn the power on/off.

If LED Power Indicator on the monitor is not lightening, then the

remote control will not work.

To move the highlight bar up to adjust the selected item when OSD menu

is on.

To move the sub-picture up when in “PIP” mode.

SMART PICTURE button

To select smart picture mode from [HIGHBRIGHT], [STANDARD],

MENU button

o turn the OSD menu on/off.

[sRGB], [CINEMA]

HIGHBRIGHT: for moving image such as Video

STANDARD: for images (Factory setting)

sRGB: for text based images

PLUS button

increase the adjustment with OSD menu.

CINEMA: for movies.

To move the sub-picture right when in “PIP” mode.

PIP (Picture In Picture) button

ON/OFF button: To turn PIP mode ON/OFF.

INPUT button: To select the input signal for the sub-picture.

CHANGE button: To exchange between the main picture and sub-

picture.

EXIT button

turn to the previous OSD menu.

DOWN button

Note:

To move the highlight bar down to adjust the selected item when OSD

menu is on.

The “PIP” and “POP” modes do not work if the screen size is

“CUSTOM” ,“DYNAMIC” or “REAL”.

CONTRAST button

To move the sub-picture down when in “PIP” mode.

To start CONTRACT OSD selection, and then push "+" or "-" button

VOLUME UP button

To increase the audio output level.

to adjust the value.

DISPLAY button

VOLUME DOWN button

To decrease the audio output level.

To turn on/off the setting information displayed on the right-up corner

of the screen.

MINUS button

To decrease the adjustment with OSD menu.

To move the sub-picture left when in “PIP” mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Operating Range for the Remote

Control

Handling the remote control

Do not subject to strong shock.

Do not allow water or other liquid to splash the remote control.

Point the top of the

sensor during button operation.

Use the emote control within

front of the LCD monitor's emote control sensor and within

emote control towar

the LCD monitor's remote

If the

remote control gets wet, wipe it dry immediately.

Avoid exposure

to heat and steam.

distance of about

m/ 23 ft from the

Other than to install the batteries, do not open the

control.

remote

horizontal and vertical angle 30° with

distance of about

m/ 10 ft.

NOTE:

strong illumination strikes the

or when ther is an obstacle in the radiation path.

remote control system may not function when direct sunlight or

remote control sensor of the LCD monitor

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

How to Mount or Attach Feet to the LCD Monitor

You can install the LCD monitor in one of the following two ways:

Way 1: Attach and remove the optional stands

How to install stands

1. Please turn the monitor off.

2. After inserting stand in guide block, fasten the thumbscrews on both sides of the monitor

NOTE:

Install the stands with their longer portions directing to the front.

In the upright position

How to remove the stands

1. Spread the protective sheet on the flat surface

2. Make the monitor lying on the protective sheet.

3. Remove screws using screwdriver and place them in

safe place for reuse.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

To avoid monitor from falling

Take measures to prevent the monitor from falling over in case of an earthquake or other disaster might occur to lessen the probability of injury and

damage.

As shown in the figure below, secure the monitor to a solid wall or pillar using rope (commercially available) strong enough to bear the weight of the

monitor(BDL5231V: approx. 47.5 kg). Screw hooks (commercially available), of ring type rather than C-shaped screw hooks (with opening), are

recommended.

Caution:

y Though the recommended prevention from falling is intended to lessen the probability of injury and damage, it doesn’t assure its effectiveness

against any kind of earthquake or disaster.

y Before moving the monitor, remove the rope that is securing the monitor.

Way II: Mount the monitor on the wall

Before mounting the monitor to the wall, make sure that the system has been power-off and you have obtain a standard wall-mounting kit

(commercially available). Using mounting interface that comply withTÜV-GS and/or UL1678 standard in North America is recommended.

1. Lay a protective sheet on a table, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch

the screen face.

2. This device cannot be used or installed without the Tabletop Stand or other mounting accessory. Make sure all these stuffs are ready for wall-

mount installation.

3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the

equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation.

4. For the wall-mounting kit, use M6 mounting screws for 400x 400 mm pattern (having a length 10 mm longer than the thickness of the mounting

bracket) and tighten them securely. (Recommended torque: 470 - 635N•cm).

Caution:

For preventing the monitor from falling.

y Install the monitor with metal brackets for wall or ceiling installation (commercially available) on your own responsibility. For detailed procedures of

installation, refer to the instructions of the metal brackets.

y To lessen the probability of injury and damage resulting from fall of the monitor in case of earthquake or other disaster, be sure to consult the

bracket manufacturer for installation location.

y To lessen the risk of falling of the monitor, thread commercially available rope (having a load capacity at least 1960N (200kgf)) through the handles

at the right and left of the monitor and secure the rope to the wall mount brackets or ceiling mount brackets.(Refer to the first paragraph of this

page.)

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Ventilation Requirements for enclosure locating

To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Setup Procedur

1. Install the system on the right location

3. Connect to external equipment

•

protect the connected equipment, tur

befor making connections.

Please refer to section “Connectivity” P.18~P.22 for operations.

off the main power

CAUTION:

THE LCD MONITOR MUST BE MOVED OR INSTALLED BY

TWO OR MORE PERSONS.

•

Failur to follow this caution may result in injury and damage when

the LCD monitor falls.

4. Connect power cord

•

The power outlet socket should be installed as near to the

equipment as possible, and should be easily accessible.

Fully insert the prongs into the power outlet socket. Loose

connection may cause noise.

CAUTION:

DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY

•

YOURSEL

The LCD display must be installed by

Contact your dealer for mor information.

qualified technician.

NOTE:

Please efer to “Safety Operation” section of this manual for

proper selection of AC power cord

CAUTION:

DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE DOWN,

FACE UP OR FACE DOWN.IT’S POSSIBILITY TO CLOCKWISE 90

DEGREES MOUNT. BUT DO NOT COUNTERCLOCKWISE 90

DEGREES MOUNT.

CAUTION:

DO NOT INSTALL THE LCD MONITOR WHERE IT WILL BE

EXPOSED TO DIRECT SUNLIGHT.

Failur to follow this caution will result in display defects.

IMPOR

ANT

Lay the protective sheet, which was wrapped around the LCD monitor

when it was packaged, beneath the LCD monitor so as not to scratch

the panel.

2. Install the remote control batteries

The

install or replace batteries:

1. Press and slide to open the cover

emote control is powered by 1.5V AAA batteries.

2. Align the batteries according to the (+) and (–) indications inside

the case.

3. Replace the cover

5. Turn on the power of the

ttached external equipment

When connected with

computer, turn on the power of the computer

first.

CAUTION:

Incorrect use of batteries can result in leaks or bursting. Be

careful especially about the following points.

6. Operate the attached external equipment

Display the signal from the external equipment

•

Place “AAA” batteries matching the

and signs on each battery

to the and signs of the battery compartment.

7. Adjust the sound

•

Do not mix battery types.

Make adjustments to lower or to rise the volume as required.

Do not combine new batteries with used ones. It causes shorter

battery life or leakage of batteries.

8. Adjust the screen

•

Remove dead batteries immediately to prevent battery

liquid from leaking into the battery compartment. Don't touch

exposed battery acid, it cause damage to your skin.

Make adjustments to the display position or settings if

required.

NOTE:

If you do not intend to use the Remote Control for

remove the batteries.

long period,

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

9. Adjust the image

Make adjustments to brightness or contrast if required.

10. Recommended Adjustment

educe the risk of “image persistence”, please adjust the

following items based on the application being used.

“POWER SAVE” “PANEL SAVING” “DATE AND TIME”

11. To prevent the main power switch

from being changed

prevent the possibility of main power switch being carelessly

pushed, please attach the main switch cover (accessory) onto it

NOTE:

With the main power switch cover in place, the main power switch

can not be turned off. Remove main power switch cover in order to

turn of the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Install the LCD Monitor in

ortrait

Mode

BDL5231V can be installed in portrait position, under the following conditions:

Caution:

Portrait mode is effective only when wall-mounted or ceiling-mounted. The feet can not be used for the monitor in portrait position.

Placing the monitor in portrait position, will shorten the average life of the LCD backlight.

Operational Environment (Temperature) shall be limited, as shown below:

Operational

Environment

mperatur

35 °C

41 95 °F

Humidity

(without condensation)

Please orientate the monitor in the direction shown as the right figure:

Do not place monitor in landscape in any other manner

Clockwise

Counterclockwise

How to set-up

1. Remove the feet if they are attached.

2. The

“

”

logo should be on the LEFT side when facing the monitor.

How to Remove the Logo for landscape mode?

1. Remove the logo sticker by forcing a piece of paper under the logo.

2. Using a knife, carefully remove the logo sticker with the paper placing

beneath.

3. Tear off the logo sticker.

How to Use the Logo Guider for Portrait Mode?

1. Before applying, make sure the guider is well shaped. The "PHILIPS"

sticker attached on the end of it could be folded back as figure a.

2.Turn back the logo end of the guider and remove the sticky tape of the

logo.

3. Slide the logo guider along the short side of the front bezel as figure c &

then re-turn the logo end of the guider back to the right side.

4. With your left hand fixing the guider, press the logo by your right hand to

make it stuck firmly on the front bezel.

5. Remove the guider and leave the logo on the front bezel.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Connectivity

Befor making connections:

First tur

off the power of all the attached equipments before make connections.

Refer to the user manual included in each separate piece of equipment.

Connectivity Diagram

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Connecting to a Personal Computer

As you finish the connection between the computer and the LCD monitor, you could play the contents in the computer

and display them on the LCD monitor

Connecting the LCD Monitor to a Personal Computer

•

o achieve this

(PC-A IN connector)

When connecting mor

available) to make connection between LCD monitor(RGB OUT connector) and the other (PC-A IN connector)

The AUDIO IN 1, 2, 3 or HDMI can be connected for audio input After choosing one of the AUDIO IN connectors, you might need to select

AUDIO 1, 2, 3 or HDMI using the AUDIO SOURCE button on the remote control.

hen connecting mor than one LCD monitors to PC, apply RCA cable to make connection between LCD monitor(AUDIO OUT connector) and

the other (AUDIO IN 1, 2, 3). HDMI source is not suitable for this case.

apply the supplied VGA signal cable (mini D-sub 15 pin to mini D-sub 15 pin) to make connection between PC and LCD monitor

than one LCD monitors to PC, apply another VGA signal cable (mini D-sub 15 pin to mini D-sub 15 pin; it’s commercially

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Connecting to a Digital Interface Equipment

Connections can be made between LCD monitor and other digital equipment that is equipped with digital interface compliant with the DVI (Digital

Visual Interface) standard.

Connect the LCD Monitor to

Computer with

Digital Output

•

The HDMI , DVI-D IN connector accepts

The HDMI , DVI-D IN connector can be chose to receive the video signal from DVI-D output of PC.

ensure the display quality use cable with quality prescribed by DVI standards.

The AUDIO IN 1, 2, 3 or HDMI connector can be chose to receive audio source Select AUDIO 1, 2, 3 or HDMI from the AUDIO SOURCE

button on the remote control. HDMI(for audio) is only selectable only when HDMI or DVI-D (for video) is selected.

Note that the signal input from HDMI / DVI-D connector cannot be output to the RGB OUT connector

HDMI cable.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Connecting to a DVD Player

As you finish the connection between the DVD player and the LCD monitor, you could display the contents from the played DVD on the LCD

monitor. You might like to refer to your DVD player manual for further information.

’s

Connect the LCD Monitor to

DVD Player

•

o achieve this

DVD player(Y, Cb/Pb, Cr/Pr Out) and LCD monitor (CVI In). You might need BNC-to-RCA adapters(including in the accessories) to convert

the BNC connectors to RCA connectors if you are using the separated signaling(Y, Cb/Pb, Cr/Pr) RCA cable

If your DVD player supports HDMI signaling, apply HDMI to HDMI cable for the connection

apply separated signaling(Y, Cb/Pb, Cr/Pr) BNC cable (mini D-sub 15 pin to mini D-sub 15 pin) to make connection between a

•

The AUDIO IN 2 , 3 (both of RCA connector type) can be used for audio input.

Select [AUDIO 1] ( for 3.5φ phone jack), [AUDIO 2], [AUDIO 3]

Or [HDMI] from the AUDIO SOURCE button on the remote control. HDMI (for audio) is selectable only when HDMI or DVI-D (for video) is

selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Connecting to a Stereo Amplifier

You can connect your stereo amplifier to your LCD monitor. Refer to your amplifier's manual for further information.

Connect the LCD Monitor to

Stereo Amplifier

•

urn on the LCD monitor and the amplifier only after all connections have been finished.

Apply an RCA cable to make connection between the amplifier (audio in) and the LCD monitor

Do not verse the audio left and right jacks.

(

audio out).

For the preferring audio signal, select [AUIDO1], [AUDIO2], [AUDIO3] or [HDMI] from the AUDIO SOURCE button on the remote control.

HDMI(for audio) is selectable only when HDMI or DVI-D (for video) is selected.

•

The AUDIO OUT RCA connectors output sound from the selected AUDIO SOURCE.

Connecting to a mount PC

You can connect your mount PC to your LCD monitor. Use M4 mounting screws for 100x234 mm to fix your mount PC.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Basic Operation

Power ON and OFF Modes

The LCD monitor power indicator will tur

of using the following three options:

green while powered on and will turn

red while powered off

The monitor can be powered on or

1. Pressing the Main Power Switch.

NOTE:

When the Main Power Switch is used to power of

LCD monitor the emote control the power button and the indicator

will not work. Make sur to tur the Main Power Switch on befor

using the other two options.

the

2. Pressing the power button.

NOTE:

Befor

pressing the power button, be sure to turn on the

Main Power button on the LCD monitor

3. Using the

remote control.

NOTE:

Befor

operating the remote control, be sure to turn on the Main

Power Switch on the LCD monitor

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Power Indicator

Status

Power ON

Green

Power OFF

Red

Power Standby when

“SCHEDULE” is enable

Power Standby

Diagnosis

Red On

Green Blinking

Red, Green

Red Blinking

* See troubleshooting

(Detecting failure)

Using Power Management

The LCD monitor follows theVESA approved DPM Power Management function.

The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or

the mouse has not been used for a certain period.

The power management feature on the LCD monitor has been set to the “ON” mode. This allows the system to enter a Power Saving Mode when no

signal is applied. This could potentially increase the life and decrease the power consumption of the LCD monitor.

Display Signal ofVideo Source Setting to [VIDEO]

Use the input button on the front panel or theVIDEO SOURCE button on the remote control to set video source to [VIDEO].

Use the COLOR SYSTEM OSD menu to select [AUTO], [NTSC], [PAL], [SECAM], [PAL60], [4.43NTSC], according to your video format.

Picture Size

HDMI, DVI-D, PC-A

FULL

NORMAL

CUSTOM

REAL

CVI , VIDEO

DYNAMIC

REAL

CUSTOM

SignalType

4:3

NORMAL SIZE

Recommended Size

NORMAL

DYNAMIC

FULL

Squeeze

NORMAL: Display with the input signal aspect ratio from PC signal, or display in 4:3 aspect ratio at CVI orVIDEO signal.

FULL: Display in the entire screen.

DYNAMIC: Expand 4:3 pictures to the entire screen with non-linearity. (Some round image might be cut by expansion.)

CUSTOM (ZOOM): Images can be expanded beyond the active display area. The image which is outside of the active display area would not be

shown.

REAL: Image will be displayed for one by one pixel.

ZOOM

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Smart Picture Mode

HDMI , PC-A

HIGHBRIGTH

STANDARD

sRGB

CVI,VIDEO

HIGHBRIGTH

CINEMA

Audio Source Switching

You can select the audio source using the AUDIO SOURCE button on the remote control.

HDMI

AUDIO1

AUDIO2

AUDIO3

Control Lock Mode

This function disables the operation o buttons so that the adjustments you make are not active when they are pressed.

To disable the buttons, press and hold down the S and T buttons together for at least 3 seconds.

To enable the buttons, press and hold down the S and T buttons together for at least 3 seconds again.

OSD Information

HDMI , PC-A

PC-A

1024

48kHz 60Hz

AUDIO : 1

ideo Source

768

Input signal Information

Audio Source

Pictur Size

SIZE FULL

CVI

AUDIO : 3

SIZE FULL

deo Source

Audio Source

Pictur Size

VIDEO<S>, VIDEO

VIDEO<S>

NTSC

AUDIO :3

Video Source

Color System of Input Signal

SIZE NORMAL

Audio Source

Pictur Size

PIP or POP

Main:PC-A

Sub:VIDEO<S>

PC-A

1024

768

Main pictur Information

48kHz 60Hz

AUDIO : 1

VIDEO<S>

NTSC

Sub pictur

Information

Main pictur

SIZE FULL

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

OSD (On-Screen-Display) Controls

Press SET button

to enable setting.

Press MENU or

EXIT button to exit.

Press MENU button to

open Main menu. Press

UP or DOWN button to

select sub-menu.

Press UP or DOWN, and PLUS or

MINUS button to select function, or

adjust the setting Press SET button

to enable the setting.

Remote Control

Press MENU button to

open Main menu. Press

UP or DOWN button

to select.

Press INPUT button to

enable the setting.

Press UP or DOWN, and PLUS

or MINUS button to select

Press MENU button to

exit.

function, or adjust the setting

Press INPUT button to enable

the setting.

Control Panel

UP or DOWN button

INPUT button

“-” “+” button

MENU button

OSD screen

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Main-Menu

PICTURE

BRIGHTNESS

Adjusts the overall image and background screen brightness.

Press

button to increase brightness.

button to decrease brightness.

CONTRAST

Adjusts the image brightness for the input signal.

Press

button to increase contrast.

button to decrease contrast.

SHARPNESS

This function is digitally capable to keep crisp image at any timings.

It is adjustable to get

distinct image or soft one as you prefer and set independently for each

pictur mode.

Press

button to increase sharpness.

button to decrease sharpness.

BLACK LEVEL

Adjusts the image brightness for the background.

Press

button to increase black level.

button to decrease black level.

NOTE: sRGB pictur mode is standard and cannot be changed.

NOISE REDUCTION

Adjusts the noise reduction level.

Press

button to increase

button to decrease

eduction level.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

TINT

INPUT HDMI , (HDMI INPUT MODE-HD), CVI, VIDEO<S>, VIDEO only

Adjusts the tint of the screen.

Press

button the flesh tone color becomes greenish.

button the flesh tone color becomes purplish.

COLOR

INPUT HDMI , DVI-D(INPUT MODE-HD), CVI, VIDEO<S>, VIDEO only

Adjusts the color of the screen.

Press

button to increase color depth.

button to decrease color depth.

COLOR TEMPERATURE

Is used to adjust the color temperature.

The image becomes

reddish as the color temperature decreases, and becomes bluish as the color

temperatur increases.

COLOR CONTROL

The color levels of red, green, and blue are adjusted by the color bars.

R: Red, G: Green, B: Blue

LIGHT SENSOR

Select “ON” to enable the ambient light sensor.The image brightness will be auto adjusted when

ambient light changed.

PICTURE RESET

Selecting Pictur

Select “Yes” and press “SET” button to

Press “EXIT” button to cancel and then retur

set allows you to

eset all OSD settings about PICTURE setting.

estor to factory preset data.

to the previous menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Main-Menu

SCREEN

POSITION

Controls Horizontal Image position within the display area of the LCD.

Press

button to move screen to right.

button to move screen to left.

POSITION

Controls Vertical Image position within the display area of the LCD.

Press

button to move screen to UP.

button to move screen to DOWN.

CLOCK

INPUT PC-A only

Press

button to expand the width of the image on the screen the right.

button to narrow the width of the image on the screen the left.

CLOCK PHASE

INPUT PC-A only

Improves focus, clarity and image stability by increasing or decreasing this setting.

ZOOM MODE

You can select “FULL”, “NORMAL” and “CUSTOM” and “REAL”. (INPUT HDMI,DVI-D,PC-A only)

You can also select “FULL”,“NORMAL” “DYNAMIC” and “CUSTOM” and “REAL”. (INPUT CVI,

VIDEO(S), VIDEO only)

Selecting “DYNAMIC” will make the screen display panoramic with the expansion of the middle and

outside of the screen changed. (The upper and the bottom of the image will be cut by expansion.)

Dynamic image is the same as FULL size image when HDTV signal is input.

Selecting “REAL” image will be displayed

pixel.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

CUSTOM ZOOM

“CUSTOM ZOOM” will be selected when you select “CUSTOM” on the screen “ZOOM” mode.

ZOOM: expands the horizontal and the vertical size simultaneously.

HZOOM: expands the horizontal size only.

VZOOM: expands the vertical size only.

POSITION: moves to the right with

button. moves to the left with

button.

–

button.

POSITION: moves up with button. moves down with

–

SCREEN RESET

Selecting Screen eset allows you to

eset all OSD settings from PICTURE setting.

Select “Yes” and press “SET” button to estor the factory preset data.

to the previous menu.

Press “EXIT” button to cancel and then retur

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Main-Menu

AUDIO

BALANCE

Adjusts the balance of L/R volume.

Press

Sound of the left side will be small.

Press button to move the stereo sound image to left.

button to move the stereo sound image to right.

TREBLE

It is to accentuate or reduce the high frequency sound.

Press

button to increase TREBLE sound.

button to decrease TREBLE sound.

BASS

It is to accentuate or

reduce the low frequency sound.

Press

button to increase BASS sound.

button to decrease BASS sound.

SPEAKER

AUDIO RESET

Selecting Audio

Select “YES” and press “SET” button to

Press “EXIT” button to cancel and then retur

eset allows you to

eset all OSD settings from AUDIO setting.

estor the factory preset.

to the previous menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Main-Menu

PIP (PICTURE IN PICTURE)

Note: The “PIP” and “POP” modes do not function when the screen size is “CUSTOM” or “REAL”.

PIP SIZE

Selecting the size of pictur inserted at the “Picture-in-Picture” (PIP) mode.

“Large”, “Middle” and “Small” ar available.

PIP AUDIO

Selecting the sound source in PIP mode.

When selecting “MAIN AUDIO”, you will get the sound for the main pictur and when selecting

“PIP AUDIO”, you will get the sound for the pictur instead.

PIP RESET

Selecting PIP Reset allows you to

Select “Yes” and press “SET” button to

Press “EXIT” button to cancel and then retur

eset all OSD settings from PIP setting.

estor the factory preset data.

to the previous menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Main-Menu

CONFIGUR

AUTO ADJUST

TION

INPUT PC-A only

Press "SET" button to automatically adjust screen size, horizontal position, vertical position, clock,

clock phase, white level and black level.

Press

EXIT

button to cancel execution AUTO ADJUST and then will return to the previous menu.

POWER SAVE

Selecting RGB "ON", the monitor will go to power management mode when HDMI, DVI-D,PC-A, sync is

lost.

Selecting VIDEO "ON", the monitor will go to power management mode after about 10 minutes delay

from when CVI and VIDEO input signal is lost.

LANGUAGE

OSD control menus ar available in eight languages.

(English, German, French, Italian, Spanish, Polish, Turkish, Russian, Simple Chinese

)

PANEL SAVING

Select "PANEL SAVING" functions to reduce the risk of the "image persistence".

COOLING FAN:The cooling fan will be auto-turned on and off according to temperature of monitor

when selected “AUTO”.The cooling fan will be turned on always when selected “ON”.

BRIGHTNESS: The brightness is decreased when selected "ON".

PIXEL SHIFT: Image is slightly expanded and moves 4 directions (U

(Need setting the time for movement).

DOWN, RIGHT LEFT) periodically

Movement area is approximately +/- 10mm from original position;

Please locate the important information such as text within 90% area of screen image.

See note (1) for this functions.

PIP and STILL will be disabled when "MOTION" is active.

COLOR SYSTEM

INPUT VIDEO(S), AV only

Selecting the Color System depends on your input video format.

AUTO: NTSC, PAL, SECAM, PAL60 or 4.43 NTSC is automatically selected.

NTSC: Specific selection of NTSC.

PAL: Specific selection of PAL.

SECAM: Specific selection of SECAM.

PAL-60: Specific selection of PAL60.

4.43NTSC: Specific selection of 4.43 NTSC.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

CONFIGURATION RESET

Selecting the CONFIGURATION RESET allows you to reset all configuration settings.

Select "Yes" and press "SET" button to

estor

the factory preset data.

Press

EXIT

button to cancel and

etur the previous menu.

ACTOR

RESET

Selecting "YES" allows you to reset PICTURE, SCREEN, AUDIO, CONFIGURATION1,2 and

ADVANCED OPTION will be back to factory settings (except LANGUAGE, DATE AND TIME and

SCHEDULE).

Select "YES" and press "SET" button to

restor

the factory preset data. Press

EXIT button to

cancel and

retur

the previous menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Main-Menu

CONFIGUR

ATION

OSD TURN OFF

The OSD control menu will stay on as long as it is use. In the OSD

how long the monitor waits after the last touch of button to shut of

The preset choices ar -120 seconds.

urn Of

submenu, you can select

the OSD control menu.

INFORMATION OSD

Selects the information OSD display or not.

The information OSD will display when input signal or source change or warning message like as

no-signal or out-of range.

time between

to 10 seconds is available.

SLEEP TIMER

select SLEEP TIMER mode ON/OFF.

In the SLEEP TIMER menu, you can preset the monitor to automatically power down.

time between to 24 hours is available.

When the SLEEP TIMER is set, the SCHEDULE settings will be disabled.

OSD

POSITION

Adjusts the horizontal position of the OSD menu.

OSD

POSITION

Adjusts the vertical position of the OSD menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

MONITOR INFORMATION

Indicates the model and serial number of your monitor

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Main-Menu

ADVANCED OPTION

INPUT RESOLUTION

INPUT PC-A only

Selects to decision of input signal about below timings,

(1)1024x768, 1280x768, 1360x768 and 1366x768.

(2) 640x480, 720x480 and 852x480

(3) 800x600, 1064x600 and 720x576

(4) 1400x1050 and 1864x1050

(5) 720x400 and 640x400

AUTO: Determines the

resolution automatically.

The setting you select becomes effective when POWER is turned OFF and ON again.

BLACK LEVEL EXPANSION

INPUT HDMI, DVI-D(MODE-HD), VIDEO(S),

only

Selects level of black expansion from “OFF”,”LOW”, “MIDDLE” and “HIGH”.

In case of go under the black cut-off level, please adjust the “Black level” in moderation on OSD menu.

GAMMA SELECTION

Selects

2.2

display gamma, It’s refer to the brightness performance curve of signal input.

2.4

gamma

Native

NOTE: sRGB pictur mode is standard and cannot be changed.

SCAN MODE

INPUT HDMI, DVI-D(MODE-HD), VIDEO(S),

only

Changes the display area of the image.

OVERSCAN: Set to display area about 95%

UNDERSCAN: Set to display area about 100%

SCAN CONVERSION

INPUT HDMI, DVI-D(MODE-HD), VIDEO(S),

only

Selects IP (Interlace to Progressive) converter function.

PROGRESSIVE: Enable the IP function, to convert interlace signal to progressive. Normally use

this setting.

INTERLACE*: Disable the IP function.

*NOTE: This mode is better suited for motion pictures, but it increases chance of image retention.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

FILM MODE

INPUT HDMI, DVI-D(MODE-HD), VIDEO(S),

only

Selects Film mode function.

AUTO: Enable the Film mode function. This mode is better suited for movies, which is converted 24

Frames/sec source to DVD ideo. ecommend to select “PROGRESSIVE” in “SCAN CONVERSION”.

OFF: Disable the Film mode function. This mode is better suited for Broadcasting or VCR source.

IR CONTROL

Selects the operation mode of the

RS-232C.

remote controller when multiple BDL5231V monitors are connected via

The item in this menu will become effective by pressing “SET” button on the selected item.

NORMAL: The monitor will be controlled normally by emote controller

PRIMARY The first BDL5231V monitor of those multi-connected via RS-232C is designated as PRIMARY

SECONDARY

designated as SECONDARY

LOCK: Disable the monitor control by infrared

BDL5231V monitors other than the first one multi-connected via RS-232C ar

emote controller

Keep pressing “DISPLAY” button during

sec or more, this setting will

tur

to “NORMAL”.

KEYBOARD CONTROL

Selects the operation mode of the keyboard control

Select “LOCK” to disable the keyboard.

Select “UNLOCK” to enable the keyboard.

TILING

TILING demonstrates multiple screens. This feature provides

It will be able to divide up to each and V.

This requires you to feed the PC output into each of the monitors through

MONITORS: Select number of horizontal divide.

MONITORS: Select number of vertical divide.

POSITION: Select position to expand the screen.

single large screen using up to 25 monitors.

distributor.

FRAME COMP: Works in tandem with TILING to compensate for the width of the tile bezels in order

to accurately display the image.

ENABLE: Select “YES”, the monitor will expand the selected position.

PIP and STILL will be disabled when “TILING” is activated.

HEAT STATUS

Disclamer: Heat sensor is indicative.

HEAT STATUS allows you to watch the thermal status at any time via the OSD menu and/or via RS232

commands.The indicated temperature has a accuracy of 3 degrees (plus and minus)..

Press “SET” button to enter the submenu to monitor the heat status

Press “EXIT” button to cancel and then return the previous menu.

DATE AND TIME

Adjusts the current date and time for internal clock.

You should set this function when you use “SCHEDULE”.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

SCHEDULE

Programs the monitor's working schedule.

Schedule the power on and power off with hour and

day of the week. Also sets the input port.

This OSD can't remove except EXIT

MONITOR ID

ID numbers for remote control are assigned to BDL4631V monitors that are multi-connected via RS-232C.

ID numbers 1 to 26 are selectable.

DDC/CI

Use to turn ON or OFF the DDC/CI communication function. Select ON for normal use.

SMART POWER

Selecting SMART POWER allows you to choose a certain level of power saving condition.

Select “OFF” to set the system in normal power condition

Select “MEDIUM” to set the system in medium level power saving status.

Select “HIGH” to set the system in high level power saving status

Press “EXIT” button to cancel and then return the previous menu.

ADVANCED OPTION RESET

Selecting ADVANCED OPTION RESET allows you to reset all OSD settings from ADVANCED OPTION

settings, except for GAMMA SELECTION, DATE AND TIME, SCHEDULE, HDMI INPUT MODE, DVI-D

INPUT MODE,MONITOR ID, and DDC/CI.

Select “YES” and press “SET” button to restore the factory preset data.

Press “EXIT” button to cancel and then return the previous menu.

GAMMA SELECTION is reset when carrying out the PICTURE RESET in the PICTURE.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

NOTE

NOTE 1: IMAGE PERSISTENCE

Please be awar

“ghost” image of

image persistence is not permanent, but constant images being displayed for

alleviate image persistence, tur of the monitor for as long as the previous image was displayed. For example, if an

that LCD

echnology may experience

phenomena known as Image Persistence. Image Persistence occurs when residual or

monitors, LCD monitors’

long period of time should be avoided.

previous image remains visible on the screen. Unlike CR

image was on the monitor for one hour and

As with all personal display devices, PHILIPS

esidual image remains, the monitor should be turned of

ecommends displaying moving images and using moving panel saving at

the monitor when not in use.

for one hour to erase the image.

regular intervals

whenever the screen is idle or turning of

Please set “POWER SAVE”, “PANEL SAVING”, “DATE AND TIME” and “SCHEDULE” functions to further

Image persistence.

reduce the risk of

For long life use of Public Display

< Image Sticking of LCD Panel

When LCD panel is operated continuously for long hours,

image of previous image may be observed. (Image Persistence)

Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD ar

the displayed image, and it is observed permanently. (Image Sticking)

trace of electric charge

emains near the electrode inside LCD, and

esidual or “ghost”

accumulated along

Recommendations

For preventing the fast transition to Image Sticking, and for longer life usage of LCD, following ar

recommended.

1. Fixed image should not be displayed for long period, and changed to another images with short cycle.

2. In case a fixed image is display for a long time, it is advised to activate the pixel shift feature that will periodically move the image in four

directions

3. When no use, please tur

Function of monitor

4. Reducing the environmental temperatur

When Protection boar (glass, acryl) is installed over the LCD surface, enclosed into the box

temperatur sensors inside monitor

educe the environmental temperature, the monitor should be set Low Brightness or Cooling Fan “ON” by using Screen sever Function.

5. Please use "Panel saving Mode" of monitor

off

the monitor by

remote control, or use Power Management Function of monitor or use Schedule

is effective for long life use.

wall, or stack the monitor, please utilize the

NOTE 2: HOW TO SETUP SCHEDULE

Using the “SCHEDULE” function allows you to set up to seven different scheduled time intervals when the LCD Monitor will be activated.

You can select the time the monitor turns on and turns off, the day of week the monitor is activated, and which input source the monitor will

use for each scheduled activation period.

effect.

check mark in the box next to the number of the schedule indicates that the selected schedule is in

select which schedule to set, use the up/down arrows to move the number (1 to 7) of the schedule.

Use the (+) and (-) buttons to move the cursor horizontally within the particular schedule. Use the

and select input port. The “SET” button is used to make selection.

If you create schedule but do not want to use power on time, select “--” in the “ON” time slot.

If you do not want to use power of time select “--” in the OFF time slot.

If ther is no input selected (“--” showing in the input spot) the input from the previous schedule will be used.

The selection of EVERY DAY within schedule takes priority over other schedules that ar set up to operate weekly. When schedules

ar overlapping, scheduled Power ON time has priority over scheduled Power OFF time.

If ther ar two schedules programmed for the same time, then the highest numbered schedule has priority

TIMER is set, the “SCHEDULE” function is disabled.

(

)

and

(

)

buttons to increase time

When the “SLEEP

”

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

NOTE 3: “PIP”, “POP” and “SIDE BY SIDE”

The following table shows the combination of signal inputs under which the “PIP” and “POP” modes function. These modes do not function,

however, when the screen size is “CUSTOM” or “REAL”.

SUB

HDMI

DVI-D

PC-A

CVI

VIDEO(S)

{

HDMI

DVI-D

PC-A

CVI

{

{: Supported

±: Not supported

VIDEO(S)

{

Press the “PIP ON/OFF” buttons on the

remote control to change between “PIP”, “POP” and “SIDE BY

SIDE” mode as shown in the diagram below

SIDE BY SIDE

ASPECT

SIDE BY SIDE

FULL

PIP

POP

OFF

A B

A A

“PIP”, “POP” mode resolution (Reference)

PIP SIZE

: 450 dots

: 675 dots

: 900 dots

: 450 dots

338 dots

450 dots

675 dots

338 dots

SMALL

MIDDLE

LARGE

POP SIZE

Remote control numbering function

By connecting multiple BDL5231V monitors using RS-232C cables, you can control any one monitor or all the monitors by one

remote controller.

1. Assign arbitrary ID number to each of multi-connected BDL5231V monitors using MONITOR ID. ID numbers 1

to 26 ar

It is recommended to assign sequential ID numbers from

2. The emote control mode of the first BDL5231V monitor is set to PRIMARY and those of the other monitors ar

SECONDARY

3. When you direct the

button on the emote controller

selectable.

and up.

set to

emote controller at the

remote control signal sensor of the PRIMARY monitor and press the DISPLAY

the ID selection OSD appears at the upper left of the screen.

ID number of the currently viewed monitor

Select the ID number of the monitor you want to control using the +/- button

on the remote controller.

The ID of the monitor you want to control is displayed at the upper left of its screen.

By selecting ALL, you can control all the multi-connected monitors.

4. Direct the

remote controller at the

emote control signal sensor of the PRIMARY monitor

OSD appears

on the monitor having the ID number you selected.

NOTE:

When the ID selection OSD is being displayed on the PRIMARY monitor

ID selection OSD and then control the monitor you selected.

press the DISPLAY button on the remote controller again to cancel the

HINT

If you set the

monitor to display the OSD screen and change the

emote control mode wrongly and

emote control operation becomes unavailable, press any button on the control panel of the

emote control mode using ADVANCED OPTION. By pressing

emote control for seconds or longer, the emote control mode is initialized to

and holding down the DISPLAY button on the

NORMAL.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Features

Full HD LCD display 1920x1080p

This display has a resolution that is referred to as Full HD.The state-of-the-art LCD screen technology has the full high-definition widescreen

resolution of 1080 progressive lines, each with 1920 pixels.This allows the best possible picture quality for HD input signals with up to 1080

lines. It produces brilliant flicker-free progressive scan pictures with optimum brightness and superb colors.This vibrant and sharp image will

provide you with an enhanced viewing experience.

Slim bezel

A slim bezel design adds a stylish look to a public display to nicely blend in most environments. Furthermore this design is ideal for tiled matrix

video walls.

Zoom function for tiled matrix

The internal zoom function enables easy implementation of a video wall matrix, without the need for expensive external equipment. Capable of

a vidiwall of 25 displays by dividing up to 5 displays each horizontally and vertically.

High brightness

Allows daylight viewing even in large public environments with high ambient light conditions due to its 700 cd/m² high brightness professional

panel.

Network controllability: RS232

Network controllability allows user to control and adjust monitors remotely through RS232 protocol.

Smart insert

Professional PC's are part of most public signage installations. Quite often they add additional depth to the public display and a lot of cable

clutter. This public display contains a Smart insert in the backcover that will fit many professional small form factor PC's. In addition it offers

provisions for efficient cable management.

SmartPower

The backlight intensity can be controlled and pre-set by the system to reduce the power consumption by up to 50%, which saves substantially

on energy costs.

Advanced anti image sticking

Static images left on-screen for extended periods of time may leave a "ghost image" or image sticking effect on LCD displays.Although image

sticking in LCD displays is not permanent, you want to prevent this to happen, especially in locations where content is shown 24/7.

Compliant with RoHS standards

Philips designs and produces display products in compliance with strict Restriction of Hazardous Substances (RoHS) standards that restrict lead

and other toxic substances that can harm the environment.

Automatic Long Cable Compensation:

Automatic long cable compensation prevents image quality degradation (color shift and dull signals) caused by long cable lengths.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Troubleshooting

No pictur

•

The signal cable should be completely connected to the display card/computer

The display car should be completely seated in its slot.

Front Power Switch and computer power switch should be in the ON position.

Check to make sur

that

supported mode has been selected on the display car

or system being used.

(Please consult display car

or system manual to change graphics mode.)

•

Check the monitor and your display car

with

espect to compatibility and

ecommended settings.

Check the signal cable connector for bent or pushed-in pins.

If nothing is displayed on the screen when HDCP device is connected,

reset the power of the device.

Power Button does not respond

•

Unplug the power cor

of the monitor from the AC outlet to tur

off

and reset the monitor.

Image persistence

•

Please be awar

“ghost” image of

constant images being displayed for

that LCD

previous image remains visible on the screen. Unlike CR

long period of time should be avoided.

echnology may experience

phenomenon known as Image Persistence. Image Persistence occurs when

monitors, LCD monitors’ image persistence is not permanent, but

alleviate image persistence, tur of the monitor for as long as

residual or

the previous image was displayed. For example,

if an image was on the monitor for one hour and

residual image remains, the monitor should be turned off for one hour to erase the image.

NOTE:

As with all personal display devices, PHILIPS

recommends displaying moving images and using

moving panel saving at regular intervals whenever the

screen is idle or turning of the monitor when not in use.

Image is unstable, unfocused or swimming is apparent

•

Signal cable should be completely attached to the computer

Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment. When the display

mode is changed, the OSD Image Adjust settings may need to be e-adjusted.

Check the monitor and your display car with espect to compatibility and ecommended signal timings.

If your text is garbled, change the video mode to non-interlace and use 60 Hz efresh rate.

•

Image of component signal is greenish

•

Check to see if the CVI input connector is selected.

LED on monitor is not lit (no green or red color can be seen)

•

Power Switch should be in the ON position and power cor

should be connected.

or mouse).

Make certain the computer is not in power-saving mode (touch the keyboard

RED LED on monitor is blinking

•

certain failur

might have occurred, please contact your nearest authorized PHILIPS service facility

Display image is not sized properly

•

Use the OSD Image Adjust controls to increase or decrease the coarse adjustment.

•

Check to make sur

that

supported mode has been selected on the display car

or system being used.

(Please consult display car

or system manual to change graphics mode.)

Selected resolution is not displayed properly

•

Use OSD Display Mode to enter Information menu and confirm that the appropriate

If not, select corresponding option.

resolution has been selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

No Sound

•

Check to see if speaker cable is properly connected.

Check to see if mute is activated.

Check to see if volume is set at minimum.

Remote Control is not available

•

Check the Remote Control’

batteries status.

Check if batteries ar inserted correctly

Check if the Remote Control is pointing at the monitor’s remote sensor

“SCHEDULE”/“SLEEP TIMER

”

function is not working properly

•

The “SCHEDULE” function will be disabled when the “SLEEP TIMER

If the “SLEEP TIMER function is enable and the power to the LCD monitor is turned of

the “SLEEP TIMER will be reset.

”

is set.

”

if the power supply is interrupted unexpectedly, then

”

Stripe Noise

Either light vertical or horizontal stripes may appear, depending on the specifi display pattern. This is no product fault or degradation.

“NO SIGNAL” is displayed on the screen

Image may not be displayed right after HDCP device is connected.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Digital Input

Specifications

Product Specifications

Specifications (BDL5231V)

Analog Input

52"

0.60 mm

1920 1080 dots

132.0 cm

LCD Module

Diagonal:

Pixel itch:

Resolution:

Color:

1.07 billion colors (depending on video car

used)

Brightness:

700 cd/m2 (typ.)

Contrast Ratio:

Response time:

4000:1 (typ.)

8 ms (typ.

to G)

iew Angle:

Up and Down 178°, Left and Right 178° (typ.) @CR>10

Frequency

Horizontal:

ertical:

15.625

50.0 58.0

13.5 -165.0 MHz

1152 x 648 mm

15.734, 31.5

91.1 kHz

85.0 Hz

Pixel Clock

25.0 -165.0 MHz

TMDS

iewable Size

Input Signal

PC-Input:

45.35

25.5 inches

Analog RGB Video: 0.7 Vp-p

Video:

Input impedance 75 ohm

Separate HV sync: TTL level (Pos./Neg.),Input Impedance 2.2K ohm

15 Pin Mini D-sub

Sync:

Input-terminal:

HDMI

Composite: 1.0 Vp-p

VIDEO Input:

Input impedance 75ohm BNC and RCA-PINJACK-INPUT

Y/C

Impedance 75 ohm S-TERMINAL-INPUT

Component: 1.0 0.7 Vp-p

Input Impedance 75 ohm BNC-INPUT

RCA PIN-JACK L/R INPUT 2, STEREO Mini Jack INPUT

Y: 1 Vp-p C: 0.286 Vp-p Input

AUDIO Input:

RS-232C:

In:

Pin Mini D-sub

Output Signal

Analog RGB Video: 0.7 Vp-p with 75 ohm terminated

PC-Output:

Video:

Separate HV sync: TTL level (Pos./Neg.)

15 Pin Mini D-sub

Sync:

Output-terminal:

VIDEO Output:

AUDIO Output:

Speaker Output:

BNC-OUTPUT

RCA PIN-JACK L/R OUTPUT

Internal Speaker

External Speaker Jack

1, Composite 1.0 Vp-p with 75 ohm terminated

1, 0.15 rms with 47k ohm terminated

(8 ohm)

Pin Mini D-sub

RS-232C:

Out:

Resolutions Supported

640

800

480 at 60 Hz

600 at 60Hz

1024

768 at 60Hz

1280 x 720 at 60Hz

1280

1360

1600

768 at 60Hz

1200 at 60 Hz

1900x1200 (reduced Blanking only)

1920 1080 at 60Hz*

Recommended Resolution

NTSC,PAL,SECAM,4.43NTSC,PAL60 DVD:480i,480p, 576i,720p,1080i,1080p

4.0 2.0 @100 240 AC, 50 60 Hz

Typically 235

Less than 1 W (Power button OFF/Main power switch ON)

40 °C 41-104 ° , Portrait : 5 35 °C 41 95 °F

(Without condensation)

60 °C -4 140 °F

90% (Without condensation)/90%-3.5%x(T

Power Supply

Power Consumption

–

Power Save:

Operational

Environment

Storage

Environment

Dimension

emperature: Landscape: 5

Humidity: 20

emperature: -20

Humidity: 10

mp-40°C) regarding over 40°C

47.59" (W) x 27.77" (H) x 4.85" (D)

47.59" (W) x 29.57" (H) x 15.95" (D)

55.12" (W) x 40.41" (H) x 10.63" (D)

Net without stand: 1209 mm (W)

705.5 mm (H)

751 mm (H)

123 mm (D)

405.1 mm (D)

Net with stand: 1209 mm (W)

Gross:

1400 mm (W)

945 mm (H)

270 mm (D)

Weight

Net without stand: 81.3 lbs

36.5 kg

Net with stand:

Gross:

83.8 lbs

103.5 lbs

Holes (400 mm pitches)

Optional Multi-purpose Fix Mount

38 kg

44 kg

Wall mounting interface

Complied Regulatory and Guidelines

Power Management

UL60950-1/C-UL/EN60950-1/FCC-A/EN55022-A/EN55024/EN61000-3-2/EN61000-3-3 /CE

VESA DPM

Plug

Accessories

Note: echnical specifications ar subject to change without notice.

Play

VESA DDC2B, DDC/CI

User's Manual, Power Cord, VGA Cable, BNC TO RCA adapter x 5, Remote Controller

Battery 2, Clamper (T prevent from falling), Cable belt x 3 (For securing cables), Screw

for Main switch cover

AAA

2, Screw for CLAMPER

2, Cable Holder

2, Main switch cover.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL5231V/00

Pin Assignment

1) Analog Video Signal Input (Mini D-SUB 15P): PC-A

Pin No

Name

Video Signal Red

Video Signal Green

Video Signal Blue

Mini D-SUB 15P

GND

DDC-GND

Red-GND

Green-GND

Blue-GND

+5V (DDC)

SYNC-GND

GND

DDC-SDA

H-SYNC

V-SYNC

DDC-SCL

2) S-VIDEO input (MINI DIN 4P):

<S>

MINI DIN 4P

Pin No

Name

GND

Y (Luminance)

(Chroma)

3) HDMI

Pin Assignment of HDMI connector:

TMDS Data0 Shield

TMDS Data0-

TMDS Data2+

TMDS Data2 Shield

TMDS Data2-

SCL

SDA

HDMI

10 TMDS Clock+

11 TMDS Clock Shield

12 TMDS Clock-

13 CEC

DDC/CEC Ground

+5V Power

TMDS Data1+

TMDS Data1 Shield

TMDS Data1-

Hot Plug Detect

14 Reserved (N.C. on device)

TMDS Data0+

4) RS-232C input/output

Pin No

Name

Mini D-SUB 9P

RXD

TXD

GND

RTS

CTS

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications ar

subject to change without notice.

www.philips.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Philips Car Stereo System SAC2505W User Manual
Philips Clock Radio MG C200 User Manual
Philips CRT Television TP3284C1 User Manual
Philips Electric Toothbrush HX6411 02 User Manual
Philips Portable DVD Player PD7000B User Manual
Philips Portable DVD Player PET748 User Manual
Philips Telephone SE4502B 17 User Manual
Philips TV Mount 32FWF1013 User Manual
Polk Audio DVD Player DR 3 User Manual
Profoon Telecommunicatie Cordless Telephone TX 117 User Manual