Philips Cable Box SWW1810 User Manual

Register your product and get support at  
SWW1810  
EN User manual  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
e Do not use this apparatus near water.  
1 Important  
f Clean only with dry cloth.  
g Do not block any ventilation openings.  
Install in accordance with the  
Safety  
manufacturer’s instructions.  
h Do not install near any heat sources such  
as radiators, heat registers, stoves, or  
other apparatus (including amplifiers) that  
produce heat.  
i Do not defeat the safety purpose of  
the polarized or grounding-type plug.A  
polarized plug has two blades with one  
wider than the other.A grounding type  
plug has two blades and a third grounding  
prong.The wide blade or the third prong  
are provided for your safety. If the provided  
plug does not fit into your outlet, consult  
an electrician for replacement of the  
obsolete outlet.  
This ‘bolt of lightning’ indicates uninsulated  
material within your unit may cause an electrical  
shock.  
The ‘exclamation mark’ calls attention to  
features for which you should read the enclosed  
literature closely to prevent operating and  
maintenance problems.  
Warning  
To reduce the risk of fire or electric shock, this  
apparatus should not be exposed to rain or moisture  
and objects filled with liquids, such as vases, should not  
be placed on this apparatus.  
j Protect the power cord from being  
walked on or pinched, particularly at plugs,  
convenience receptacles, and the point  
where they exit from the apparatus.  
Caution  
k Only use attachments/accessories specified  
by the manufacturer..  
To prevent electric shock, fully insert the plug. (For  
regions with polarized plugs:To prevent electric shock,  
match wide blade to wide slot.)  
l Use only with the cart, stand, tripod,  
bracket, or table specified by the  
manufacturer or sold with the apparatus.  
When a cart is used, use caution when  
moving the cart/apparatus combination to  
avoid injury from tip-over.  
Important Safety Instructions  
a Read these instructions.  
b Keep these instructions.  
c Heed all warnings.  
m Unplug this apparatus during lightning  
storms or when unused for long periods of  
time.  
d Follow all instructions.  
4
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
n Refer all servicing to qualified service  
personnel. Servicing is required when  
the apparatus has been damaged in any  
way, such as power-supply cord or plug  
is damaged, liquid has been spilled or  
objects have fallen into the apparatus, the  
apparatus has been exposed to rain or  
moisture, does not operate normally, or  
has been dropped.  
o Battery usage CAUTION To prevent  
battery leakage which may result in bodily  
injury, property damage, or damage to the  
unit:  
Do not mix batteries (old and new or  
carbon and alkaline, etc.).  
Remove batteries when the unit is not  
used for a long time.  
p Apparatus shall not be exposed to  
dripping or splashing.  
q Do not place any sources of danger on the  
apparatus (e.g. liquid filled objects, lighted  
candles).  
Warning  
Use only the provided power adapter.  
EN  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
2 YourWireless  
HD AV Connect  
HDMI cable  
Congratulations on your purchase and welcome  
to Philips!  
To fully benefit from the support that Philips  
com/welcome.  
IR blaster extender cable  
What is in the box  
Note  
Make sure you have all these items in the box. Contact  
your dealer for any missing or damaged items.  
Power adapter for the transmitter and receiver  
x 2  
IR sensor extender cable  
Transmitter  
Anchors x 2  
Screws x 2  
Quick Installation Guide  
Adhesive tape x 2  
Quick start guide  
Receiver  
User manual  
Remote control  
6
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3 Overview  
The receiver  
Top view  
The transmitter  
Front view  
1
2
Source LEDs Indicators for HDMI1  
and HDMI2  
Power  
Press to turn the receiver  
1
2
Source LEDs It displays the current  
source input.  
button with on/off.  
the LED  
indicator  
SOURCE  
Press to switch the  
source input of the  
transmitter.  
button  
3
Source  
button  
Press to select the  
source input.  
3
Power button Press to turn the  
with the LED transmitter on/off  
indicator  
Rear view  
Rear view  
1
2
DC IN  
jack  
HDMI  
OUT  
adapter  
Connect the power adapter  
of the receiver.  
Connect the HDTV with an  
HDMI cable.  
ER  
POW  
1
DC IN jack Connect the power  
adapter of the transmitter.  
2 & 3 HDMI IN Connect the HD audio/  
3
IR IN jack Plug in the IR sensor  
extender cable.  
adapters  
video device with the  
HDMI cables.  
4
IR OUT  
blaster  
extender  
jack  
Plug in the IR blaster  
extender cable.  
EN  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The remote control  
1
2
3
POWER Press to turn the  
button  
transmitter and receiver  
on/off.  
INFO  
button  
Displays on the HDTV  
the connection status of  
the receiver.  
IR  
button  
Press to switch the IR  
blaster frequency to meet  
the requirement of the  
source device.  
4
SOURCE Press to switch the  
button  
audio/video source  
inputs connected to the  
transmitter.  
The Wireless HD AV Connect gives you a total  
wireless solution to place your HDTV set or  
projector anywhere you want.The transmitter  
can transmit uncompressed video content  
over 65 feet (19.7 meters) without latency.The  
receiver can receive signals for viewing on your  
HDTV.All you need to do is to:  
Connect the transmitter to your HD  
devices. Examples of HD devices are cable/  
satellite box, Blu-Ray/HD DVD player, game  
console or computer.  
Note  
These devices must have an HDMI port..  
Connect the receiver to your HDTV set.  
Control the transmitter with the remote  
control.  
8
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2 Connect the supplied power adapter to  
4 Installation  
the transmitter.  
Connect one end of the power  
adapter to the DC IN jack of the  
transmitter.  
Connect the transmitter to  
your HD devices  
Connect the other end of the power  
adapter to a power outlet.  
The power button of the transmitter  
is lit in solid blue and turns red in  
standby mode.  
»
You can connect two audio/video sources to  
the transmitter at the same time, but only one  
source can be selected and played.  
Connect the receiver to the  
HDTV set  
HDMI OUT  
IR IN  
DC 5V  
2
1
1 Connect the audio/video source to the  
HDMI IN  
transmitter using the supplied HDMI cable.  
Connect one end of the HDMI cable  
to the HDMI IN connector of the  
transmitter.  
1 Connect the receiver with an additional  
HDMI cable (not supplied):  
Connect one end of the HDMI cable  
to the receiver.  
Note  
Connect the other end to the HDMI  
IN connector of your HDTV.  
There are two HDMI IN ports but only one HDMI  
cable is supplied.To connect two audio/video sources  
to the transmitter at the same time, you need an  
additional HDMI cable.  
2 Connect the supplied power adapter to  
the receiver:  
Connect one end of the power  
adapter to the DC IN jack of the  
receiver.  
Connect the other end of the power  
adapter to a power outlet.  
The power button of the receiver is lit  
in solid blue and turns red in standby  
mode.  
Connect the other end of the HDMI  
cable to the HDMI OUT connector of  
the video source.  
»
EN  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5 Extend and stick the IR sensor extender  
Connect the IR blaster and IR  
sensor extender cables  
cable onto the front side of your HDTV.  
Note  
Tip  
The IR blaster support 47KHz remote signal protocol,  
while the IR sensor supports 36KHz - 56KHz (NEC,  
RC5, RC6) remote signal protocol.  
If you cannot use the remote control of your device,  
follow the steps in this section to connect the sensor  
extender cables .  
Install remote control  
batteries  
Caution  
Risk of explosion! Keep batteries away from heat,  
sunshine or fire. Never discard batteries in fire.  
Risk of decreased battery life! Never mix different  
brands or types of batteries.  
Risk of product damage! When the remote control is  
not used for long periods, remove the batteries.  
Connect the infrared blaster or sensor extender  
cables if necessary.  
1 Plug the IR blaster extender cable into  
the IR OUT blaster extender jack of the  
transmitter.  
1 Open the battery compartment.  
2 Extend and stick the IR blaster extender  
cable onto the front panel of the HD  
device.  
2 Insert two AAA batteries with correct  
polarity (+/-) as indicated.  
3 Close the battery compartment.  
3 After the IR blaster extender cable is  
connected to the transmitter, you can  
control your HD device with the remote  
control. Make sure that the remote control  
points to the receiver.  
4 If the distance between the receiver and  
receiver has obstruction (e.g. the receiver  
is mounted at the back of the HDTV), plug  
the IR sensor extender cable into the IR  
IN jack of the receiver.  
10 EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
On screen display on HDTV  
5 Activate your  
Wireless HD AV  
Connect and set  
up the link  
On screen Mode and status  
display  
Standby mode: it is a power-  
saving mode  
.....  
Start up in progress: It takes 15-  
20 seconds.  
x and .... Searching available channels: It  
occurs when the link cannot  
establish over 80 seconds after  
initialization.  
Turn on the power of your  
HDTV  
HDMI On mode with unrecognized  
HDMI OUT  
IR IN  
CH1  
video format  
DC 5V  
HDMI On mode but without input  
HDM  
I
CH1  
from the source device  
HDMI On mode with recognized video  
CH1 1080P format  
M
I H D  
1 Go to the source menu under the settings  
menu of your HDTV.  
2 Select the HDMI input to which the  
receiver is connected.  
EN 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Select the source on the transmitter  
Activate the wireless link  
Press the source buttons on the remote  
control, transmitter or receiver until you see the  
available video from your device.  
Switch on the transmitter and receiver  
In standby mode, a red power LED displays on  
the transmitter and receiver.You can then turn on  
the transmitter and receiver in the following ways:  
Tip  
For information on the LED indicator status, see the  
section on ‘LED indicator status of the transmitter’.  
LED indicator status of the  
transmitter and receiver  
Power Source Mode and status  
LED  
Solid  
red  
LED  
Off  
Standby mode: it is a  
power-saving mode  
Press on the remote control.  
» Both the transmitter and receiver are  
turned on.  
Flashing Flashing Start up in progress: It takes  
blue blue 15-20 seconds.  
Flashing Flashing Searching available channels:  
blue  
It occurs when the link  
cannot establish over 80  
seconds after initialization.  
Flashing On mode but without  
quickly input from the source  
device  
Solid  
blue  
Solid  
blue  
Solid  
blue  
Flashing On mode with  
slowly unrecognized video format  
Solid  
blue  
On mode with recognized  
video format  
Press on the transmitter and receiver.  
Note  
If the link is not established after 80 seconds, move the  
transmitter, receiver and HDTV closer to each other.  
The maximum transmission range is up to 65 feet (19.7  
meters).  
If more than one set of Philips Wireless HD AV Connect  
is placed in the same room, make sure that the minimum  
distance among each one is 6 feet 6 inches (2 meters).  
If using a computer, make sure the video format is  
supported before the video is displayed, see the  
chapter on ‘Technical data’ for information.  
Establish the link between the  
transmitter and receiver  
A flashing blue power LED displays until  
the signal link between the two units are  
established. Normally, it takes around 15-20  
seconds for the link to establish successfully.  
If using a computer, and the picture on yourTV is  
not full screen, see the chapter on ‘Frequently asked  
questions’ for information.  
12 EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5 Hook the key holes at the back of the  
6 Mount your  
receiver  
receiver on the screws.  
You can either mount the receiver on the wall  
or on the back of the HDTV.  
Mount your receiver on the  
wall  
1 Select a spot near the HDTV.  
2 Drill two holes in the wall. Make sure that  
the distance between the two holes is  
1 25/32” (45 mm) and the diameter of the  
hole is 3/16” (5 mm).  
3 Punch the supplied two anchors into the  
two holes on the wall.  
4 Put the two screws into the anchors and  
leave 1/8” (3 mm) to mount the receiver on.  
EN 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
6 Align the adhesive tape on the receiver  
with the one on the HDTV until both the  
receiver and HDTV are mounted together  
firmly.  
Mount your receiver on the  
back of the HDTV  
1 Remove the white protective film from  
one of the supplied adhesive tapes.  
Note  
2 Secure the glued side of the adhesive tape  
and attach it to the central bottom area of  
the receiver.  
The use of adhesive tapes is an alternative mounting  
option when the receiver cannot be fixed.  
When you mount the receiver at the back of the  
HDTV, avoid blocking the ventilation holes of the  
HDTV.  
For safety reason, check regularly if the HDTV and  
receiver are mounted together firmly.  
The receiver is not recommended for in-the-wall  
installation.  
3 Select a flat location on the rear side of  
the HDTV.  
4 Remove the white protective film from the  
other adhesive tape.  
5 Secure the glued side of the adhesive tape  
and attach it to the selected rear side of  
the HDTV.  
14 EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Power supply:  
7 Technical data  
Input:AC 100~ 240V  
Output: DC 5V, 2A  
Operating temperature:  
0~40°C/32~104°F  
Supported resolution  
Video format  
timings  
Resolution  
Transmitter interfaces  
Primary CEA  
video timing  
480p  
480p  
480p  
576p  
720p  
720p  
1080i  
-
A/V interfaces  
HDMI input:Two (Type A)  
Control signal interfaces  
IR blaster extender: 2.5mm jack  
Power interface  
Power input: 5V DC jack  
Switches  
Top power switch: One  
Top source switch: One  
LEDs  
Power LED: 1 x blue/red LED  
Source LED: 2 x blue LED  
Dimensions  
640x480p @ 59.94/60Hz  
720x480p @ 59.94Hz  
720x480p @ 60Hz  
720x576p @ 50Hz  
1280x720p @ 50Hz  
1280x720p @ 59.94/60Hz  
1920x1080i @ 50Hz  
1920x1080i @ 59.94/60Hz  
1920x1080p @ 50Hz  
1920x1080p @ 59.94/60Hz  
1080i  
1080p/60  
1080p/60  
194.8 x 146.8 x 31 mm (W x L x H)  
Secondary CEA  
video timing  
1080p/24  
1080p/24  
1080p/24  
Receiver interfaces  
1920x1080p @ 23.98/24Hz  
1920x1080p @ 25Hz  
1920x1080p @ 29.97/30Hz  
A/V interfaces  
HDMI output: One (Type A)  
Control signal interfaces  
IR sensor: available  
Power interface  
Power input: 5V DC jack  
Switches  
Product specifications  
Top power switch: One  
Top source switch: One  
LEDs  
General specification  
Video resolution  
Power LED: 1 x blue/red LED  
Source LED: 2 x blue LED  
Signal quality status: On-screen display  
Dimensions  
HDMI input: 1080p, 1080i, 720p, 576p, 480p  
Supported audio formats:  
Digital audio: up to 6 Mbps AC3 and DTS  
Analog audio: 32-96 KHz and 16-24 bits per  
audio sample  
194.8 x 146.8 x 31 mm (W x L x H)  
Transmission distance:  
Maximum 65 feet (19.7 meters)  
Antennas:  
High performance internal antennas  
Operating frequencies:  
5.15-5.25/5.725-5.825 GHz  
EN 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
IMPORTANT NOTE:  
Radiation Exposure Statement:  
8 Notice  
This equipment complies with FCC  
radiation exposure limits set forth for an  
uncontrolled environment.This equipment  
should be installed and operated with  
minimum distance 20cm between the  
radiator & your body.  
Notice for USA  
This equipment has been tested and found  
to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable  
protection against harmful interference in a  
residential installation.This equipment generates,  
uses and can radiate radio frequency energy  
and, if not installed and used in accordance with  
the instructions, may cause harmful interference  
to radio communications. However, there is  
no guarantee that interference will not occur  
in a particular installation. If this equipment  
does cause harmful interference to radio or  
television reception, which can be determined  
by turning the equipment off and on, the user is  
encouraged to try to correct the interference  
by one of the following measures:  
This transmitter must not be co-located  
or operating in conjunction with any other  
antenna or transmitter.  
Note  
The country code selection is for non-US model only  
and is not available to all US model. Per FCC regulation,  
all wireless product marketed in US must fixed to US  
operation channels only.  
Notice for Canada  
This device complies with RSS-210 of the  
Industry Canada Rules. Operation is subject to  
the following two conditions: (1)This device  
may not cause harmful interference, and (2) this  
device must accept any interference received,  
including interference that may cause undesired  
operation.  
Reorient or relocate the receiving antenna.  
Increase the separation between the  
equipment and receiver.  
Connect the equipment into an outlet on  
a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced  
radio/TV technician for help.  
IMPORTANT NOTE:  
Radiation Exposure Statement:  
FCC Caution:Any changes or modifications not  
expressly approved by the party responsible for  
compliance could void the user’s authority to  
operate this equipment.  
This equipment complies with IC radiation  
exposure limits set forth for an uncontrolled  
environment.This equipment should be installed  
and operated with minimum distance 20cm  
between the radiator & your body.  
Operations in the 5.15-5.25GHz / 5.725-  
5.825GHz band are restricted to indoor  
usage only.  
This device complies with Part 15 of the FCC  
Rules. Operation is subject to the following  
two conditions: (1)This device may not cause  
harmful interference, and (2) this device must  
accept any interference received, including  
interference that may cause undesired  
operation.  
Caution  
The device for operation in the band 5150-5250 MHz is  
only for indoor use to reduce the potential for harmful  
interference to co-channel mobile satellite systems;  
the maximum antenna gain permitted for devices in the  
band 5725-5825 MHz shall comply with the e.i.r.p. limits  
specified for point-to-point and non point-to-point  
operation as appropriate.  
16 EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
negative consequences on the environment and  
human health.  
additional information on a recycling center in  
your area.  
Recycling  
Your product is designed and manufactured  
with high quality materials and components,  
which can be recycled and reused.  
Never dispose of your product with other  
household waste. Please inform yourself about  
the local rules on the separate collection of  
electrical and electronic products.The correct  
disposal of your old product helps prevent  
potentially negative consequences on the  
environment and human health.  
HDMI, and HDMI logo, and High-Definition  
Multimedia Interface are trademarks or  
registered trademarks of HDMI licensing LLC in  
the United States and other countries.  
OneYear LimitedWarranty  
The packaging of this product is intended to  
be recycled. Contact your local authorities for  
information about how to recycle the packaging.  
Philips warrants that this product shall be free  
from defects in material, workmanship and  
assembly, under normal use, in accordance with  
the specifications and warnings, for a period  
of one year from the date of purchase.This  
warranty extends only to the original purchaser  
of the product, and is not transferable.To  
exercise your rights under this warranty, you  
must provide proof of purchase in the form of  
an original sales receipt that shows the product  
name and the date of purchase. For customer  
support or to obtain warranty service, please  
or dial in 1-888-744-5477.THERE ARE NO  
OTHER EXPRESS OR IMPLIED WARRANTIES.  
Philips’ liability is limited to repair or, at its  
sole option, replacement of the product.  
Incidental, special and consequential damages  
are disclaimed where permitted by law.This  
warranty gives you specific legal rights.You may  
also have other rights that vary from state to  
state.  
When this logo is attached to a product, it  
means a financial contribution has been paid to  
the associated national recovery and recycling  
system.  
Disposal of your old product  
and batteries  
Your product is designed and manufactured  
with high quality materials and components,  
which can be recycled and reused.  
Never dispose of your product with other  
household waste. Please inform yourself about  
the local rules on the separate collection of  
electrical and electronic products and batteries.  
The correct disposal of these products helps  
prevent potentially negative consequences on  
the environment and human health.  
Your product contains batteries, which cannot  
be disposed of with normal household waste.  
Please inform yourself about the local rules on  
separate collection of batteries.The correct  
disposal of batteries helps prevent potentially  
EN 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
9 Frequently asked question  
The power LED on the  
receiver is not lit up in red in  
standby mode.  
Make sure that there is power supply for the transmitter and  
receiver.  
The computer screen image is 1 Right-click on an open space on your desktop.  
not full screen on myTV.  
2 Select Graphics Options > Output to > DigitalTelevision (Now  
the laptop image will only appear on yourTV).  
3 Once again, right-click on an open space on your desktop.  
4 Select Screen Resolution.  
5 On the pop-up box increase the resolution settings till the laptop  
image better fits yourTV screen.  
6 Select OK and KEEP CHANGES when you are satisfied with  
your image size..  
There is no video displayed on •  
myTV screen.  
Make sure that the appropriate cables are selected and inserted  
to the transmitter, receiver, and HDTV.  
Make sure that you select HDMI as the input source on your  
HDTV.  
Check the power LED and SOURCE LED on the receiver:  
Flashing blue power LED: Make sure that the transmission  
range between receiver and transmitter is not over 65 feet  
(19.7 meters) transmission distance. Move the transmitter  
closer to the receiver.  
Solid blue power LED + slow and flashing source LED:1)  
Make sure that the frame rate and video resolution of your  
source device equipment are supported and conformed to  
the technical specification. 2) Connect the source device to  
yourTV with an HDMI cable to check the compatibility of  
the video format. 3) Make sure that the video solution your  
source device is supported (See the chapter ‘Technical data’).  
Solid blue power LED + quick and flashing source LED: 1)  
Make sure that the proper cables are connected among the  
transmitter, receiver and HDTV. 2) Make sure that the source  
devices connected to the transmitter are powered on.  
18 EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
If the picture quality is poor,  
what do I do?  
Make sure that the video resolution of your source device  
matches the resolution of your HDTV.  
Make sure that the transmission range between receiver and  
transmitter is not over 65 feet (19.7 meters) transmission  
distance.  
Tip  
For information, see the chapter on ‘Technical data’.  
I cannot hear any sound or the  
Make sure that theTV volume is adjusted correctly.  
Make sure that theTV volume is not set to minimum or the  
sound is not muted.  
sound is poor, what do I do?  
Make sure that the audio format is supported.  
Make sure the HDMI cable of the transmitter is connected  
correctly.  
Tip  
For information, see the chapter on ‘Technical data, section ‘Product specification’.  
I cannot control the source  
device with the IR blaster.  
Make sure that the IR blaster and IR sensor extender cables are  
facing the IR lens of the HD device.  
Press the IR button on the remote control to change the IR  
blaster frequency based on the requirement of the source device.  
Tip  
For information, see the chapter ‘Installation’, section ‘Connect to IR blaster and IR  
sensor extender cables’.  
EN 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20 EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© 2011 Koninklijke Philips Electronics N.V.  
All rights reserved.  
IFU_SWW1810_EN_V2.0  
WK11485  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco Car Video System PMCL317A User Manual
Philips Car Stereo System AQ4140 User Manual
Philips Car Stereo System CED780 User Manual
Philips Flat Panel Television PT418APT A User Manual
Philips Home Theater System DC310V User Manual
Philips Projection Television 7P5441C199 User Manual
Philips Stereo Amplifier BGD814 User Manual
Plantronics Headphones CS60 DECT User Manual
Polaroid Digital Camera IS326 RED User Manual
Polaroid Digital Camera PIC 300B User Manual