Philips CD Player AZ5160 User Manual

VCD MP3 CD Soundmachine  
AZ5160  
Register your product and get support at  
User manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0
!
#
4
5
1
2
3
@
8
9
7
6
$
^
%
&
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
INDEX  
MP3 General Information..............6  
Controls .........................................7  
Remote Controls.........................7-8  
Power Supply ...........................9-10  
General Operation / Radio ..........10  
CD/VCD/MP3-CD  
English  
...............................................11–17  
Cassette recorder..................18–19  
Maintenance ..........................19-20  
Troubleshooting...........................21  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
MP3 General Information  
Dear Customer,  
Thank you for buying the Philips MP3-CD Soundmachine. Your great new acquisition will allow you to  
listen to up to 10 hours of CD-like quality music, using the innovative new music compression  
technology MP3.  
MP3 technology  
MP3 is short for MPEG1 Layer-3 encoding and decoding technology, a very powerful encoding  
algorithm with which you can shrink down the orginal digital audio sound data with a factor of up to  
10 without losing significant sound quality.  
Recording and Playback  
It is recommended to set your recording bit rate to 128kbps, sampling frequency at 44.1kHz  
to achieve CD-like music playback quality.  
Since downloading MP3 files from the Internet, ripping songs from your own legal CD’s and burning  
MP3 songs onto a CD-R, are a delicate process, the quality of a MP3 song may vary by these process.  
Subsequently, making a MP3-CD may not be entirely perfect.  
As a result of the above imperfection, you may experience an occasional “skip” while  
listening, or an occasional delay in accessing “previous/next” title to MP3-CD’s. This is  
considered to be normal.  
A comparison chart is enclosed as below:  
Sound  
Bit  
Approximate  
Approximate total Comment  
Quality  
Rate  
Reduction Ratio MP3-CD time  
MW radio  
FM radio  
Near-CD  
CD-like  
CD  
32 kbps 40 : 1  
40 hrs  
20 hrs  
15 hrs  
10 hrs  
5 hrs  
Sound quality significantly  
affected-not recommended.  
Balanced sound quality  
compression rate.  
64 kbps 20 : 1  
96 kbps 15 : 1  
128 kbps 10 : 1  
256 kbps  
320 kbps  
5 : 1  
3 : 1  
Compression rate low  
CD  
3 hrs  
suggest to play CDs instead.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLS  
Congratulations on your purchase and  
welcome to Philips!  
To fully benifit from the support that  
Philips offers, register your product at  
IMPORTANT!  
PLEASE NOTE THAT THE VOLTAGE  
SELECTOR LOCATED IN THE BATTERY  
COMPARTMENT AT THE REAR OF THIS  
SYSTEM IS PRESET AT 220V FROM THE  
FACTORY. FOR COUNTRIES THAT  
OPERATE AT 110V-127V PLEASE  
ADJUST TO 110V-127V BEFORE YOU  
SWITCH ON THE SYSTEM.  
TOP AND FRONT PANEL  
1 Source selector - power on/off switch and to  
select source of sound source:  
CD/TUNER/TAPE.  
SUPPLIED ACCESSORIES  
2 VOLUME - to adjust volume level.  
3 DBB (Dynamic Bass Boost) - for a more  
vivid bass response.  
Remote Control . . . . . . . . . . . . . . . . . . . .1 pc  
Mains Cord . . . . . . . . . . . . . . . . . . . . . . .1 pc  
Audio / Video Cable . . . . . . . . . . . . . . . .1 pc  
4 LIFT - OPEN - to open the CD door.  
5
Cassette keys:  
REMOTE CONTROL  
; - to interrupt recording or playback.  
9 / - to stop the tape and to open the cassette  
holder.  
5 / 6 - to fast wind/rewind the tape.  
1 - to start playback.  
1 OSD - to switch on/off the on screen display on  
the TV screen.  
2 RepAll  
0 - to start recording.  
6 LCD Display - to show the VCD, MP3 functions  
for CD/VCD/MP3-CD to repeat a whole disc.  
3 Rep  
and disc status.  
iR - infrared sensor for remote control  
8 PROG - for CD/VCD/MP3-CD to programme  
disc tracks  
9 REPEAT - to repeat a track/programme/entire  
CD playback  
for MP3-CD.................to repeat a track, or the  
whole disc.  
for CD/VCD . . . . . . . .to repeat a disc track or  
the whole disc.  
7
4 ProG  
for CD/VCD/MP3-CD..to programme disc tracks.  
5 ZOOM  
for VCD only ................ to zoom in or zoom out  
picture.  
6 Slow - to watch a VCD at a slower speed (for  
VCD operation only).  
7 A - B - to playback a certain scene or passage  
repeatedly (for CD/VCD/MP3 operation ).  
8 SHUFF - When in CD/VCD/MP3 mode, press to  
start or stop shuffle play mode (for VCD, only  
available in PBC off mode)  
9 Mute - to switch playback sound off and on  
0 GoTo - to start playback at any chosen time on  
the disc (for CD/VCD operation only and PBC  
mode is off).  
0 BAND - to select FM or MW waveband  
BACK PANEL  
! TUNING - to tune to radio stations  
@ 2; - to start or interrupt CD playback.  
9 - to stop playback  
/ § - to skip or search a passage or a track  
Telescopic aerial - to improve FM radio  
reception  
VIDEO/AUDIO OUT - connect to the TV or  
VCR VIDEO/AUDIO IN  
#
$
% AC MAINS ~ - socket for mains lead  
^ Battery door - to open the battery  
compartment  
& Voltage Selector - to adjust and match the  
local voltage 110/220V before plugging in the  
set.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
REMOTE CONTROL  
! View - to scan through a VCD with 9 pictures  
display on TV screen.  
@ 2;  
1
2
3
7
8
- to start or interrupt playback.  
¡ / ™  
9
for MP3-CD only . . . . to select previous/next  
4
title.  
for CD/VCD . . . . . . . . to search backward/  
forward track.  
0
!
5
6
@
$
5
/
6
(for CD/VCD/MP3-CD)  
- to search back or forward.  
#
^
# Audio - to select channel left / channel right /  
stereo sound, or to select a language in a  
bilingual VCD (for VCD operation only).  
$ NTSC/PAL - to select the video output for  
NTSC or PAL system.  
&
%
*
%
AL+/-  
for MP3-CD only . . . . to select the previous /  
next album  
(
¡
^ 9 - to stop playback or to clear a programme.  
& TV VOL + / - - to adjust volume level on the TV,  
with maximum 16 volume levels  
)
* PBC (PLAYBACK CONTROL) - to switch on or  
off PBC mode (for VCD version 2.0 only).  
( Digits 0 - 9  
for CD/VCD/MP3-CD - to select a  
track number.  
(numbers consisting more than 2 figures must  
be keyed in within 2 seconds)  
) Return - to return to the previous MENU level  
during playback (for VCD with PBC on).  
¡ Resume - to resume playback in stop mode.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
POWER SUPPLY  
IMPORTANT!  
The system is equipped with a Voltage Selector, set the VOLTAGE SELECTOR (located  
in the battery compartment) to match the local power line.  
For best CD/MP3-CD/VCD playback, please plug in your set to an AC power supply  
where convenient.  
If operated in DC mode, see below approximate playtime. (Playtime is also varied from  
different brand batteries) :  
Battery type  
Playtime  
Alkaline  
approximate 9 hrs  
Zinc Cartonate  
approximate 45 minutes  
The CD part of this system also serves as a Video CD player if you connect it to your  
TV set.  
Before viewing the Video CD, ensure that the set is switched to corresponding PAL or  
NTSC system of your TV set (exception Multi-system TV).  
BATTERIES (NOT SUPPLIED)  
Whenever convenient, use the mains supply if you want to conserve battery life. The battery supply  
will be switched off when the set is connected to the mains. Make sure you remove the plug from the  
set and wall outlet before inserting batteries.  
Batteries  
1. Open the battery compartment and insert six batteries, type  
R14, UM2 or C-cells, (preferably alkaline) with the correct  
polarity as indicated by the "+" and "-" symbols inside the  
6 x 1.5V R14/ UM2/ C CELL  
compartment.  
Remote control  
1. Open the battery door and insert two batteries,  
type AAA, R03 or UM4 (preferably alkaline).  
2. Replace the compartment door, making sure the batteries are  
firmly and correctly in place.  
3. Remove the batteries if they are exhausted or if they will not be used for a long period.  
– The incorrect use of batteries can cause electrolyte leakage and will corrode the compartment  
or cause the batteries to burst. Therefore:  
– Do not mix battery types, e.g. alkaline with zinc carbonate.  
– When inserting new batteries, replace all at the same time.  
– Remove the batteries if the set is not to be used for a long time.  
Note :  
– The battery supply is switched off when the set is connected to the mains.  
TV screen is disabled during CD / MP3-CD playing if your AZ5160 is battery  
powered.  
Batteries contain chemical substances, so they should be disposed of properly.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
GENERAL OPERATION  
MAINS  
1. Check if the mains voltage as shown on the type plate (on  
the bottom of the set) corresponds to your local mains  
voltage. If it does not, consult your dealer or service  
organization.  
2. Connect the mains lead to the AC MAINS ~ socket and the  
wall socket.  
The set is now ready for use.  
3. To switch off the mains supply completely, pull the mains plug out of the wall socket.  
Disconnect the mains lead when you change over to battery supply, or to protect the set  
during heavy thunderstorms.  
The type plate is located on the bottom of the set.  
GENERAL OPERATION  
1. To switch on the set, adjust the source selector.  
2. Adjust the sound using the VOLUME and DBB controls.  
3. To switch off the set, adjust the source selector to the  
TAPE/OFF position, with the cassette keys released.  
RADIO RECEPTION  
1. Set the source selector to TUNER.  
2. Adjust BAND to FM or MW as your desired band.  
3. Adjust the sound using the VOLUME controls and the DBB  
switch.  
4. Tune to a radio station using the TUNING knob.  
– For FM, pull out the telescopic aerial. To improve FM-reception,  
incline and turn the aerial. Reduce its length if the FM-signal is  
too strong (very close to a transmitter).  
– For MW, the set is provided with a built-in aerial, so the  
telescopic aerial is not needed. Direct the aerial by turning  
the whole set.  
5. To switch off, set the source selector to the TAPE/OFF  
position (with the cassette keys released).  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD/VCD/MP3-CD  
CAUTION  
Use of controls or adjustments or performance of procedures other than herein  
may result in hazardous radiation exposure or other unsafe operation.  
Environmental information  
All unnecessary packaging material has been omitted. We have done our utmost to make the  
packaging easily separable into three mono materials: cardboard, polystyrene and plastic.  
Your set consists of materials which can be recycled if disassembled by a specialized  
company. Please observe the local regulations regarding the disposal of packaging  
materials, exhausted batteries and old equipment.  
DISCS FOR PLAYBACK  
This set can play all digital audio CD, video CD, finalised digital audio CD-Recordable (CDR) discs  
and finalised digital audio CD-Rewritable (CDRW) discs.  
Support following MP3-CD formats:  
ISO 9660 or ISO 9660 + Joliet format - Max. 30 characters  
Max. Track number is 400  
Max. nested directory is 8 levels  
The max. album number is 99  
The max. MP3 programme track number is 20  
The max. length of each track is 99 minutes 59 seconds  
The player can play mixed mode disc of CD / MP3-CD  
Supported VBR bit-rate  
Supported sampling frequencies for MP3 disc : 8 kHz to 48 kHz (44.1kHz preferably)  
Supported bit-rates of MP3 disc are: 32 - 320 kbps (128 kbps preferably)  
Following formats are not supported  
The files like *.WMA, *AAC, *.DLF, *.M3U, *.PLS, MP3 PRO and JPEG CD  
The non-session closed discs  
LOADING A DISC  
1. Set the source selector to CD.  
2. Lift to open the CD door.  
"OP" will be displayed  
MP3  
3. Insert a disc with the label side facing up.  
4. Close the CD door.  
L
R
The total number of tracks of the disc appear on the display.  
"NO" will be displayed if no disc is inserted or error in CD  
operation  
For MP3-CD only  
The total track number "XXX" and album number “AXX" will  
be displayed interchangeably.  
L
R
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD/VCD/MP3-CD  
On TV screen, the album list is displayed (max. 10 lines per page). The current selected music  
is highlighted.  
Notes : - To ensure good system performance, wait until the disc completely reads before  
proceeding.  
- For MP3-CD, the disc reading time may exceed 1 minute due to the large number of  
songs compiled into one disc.  
PLAYING A NORMAL DISC  
1. Press 2; to start playback.  
The track number of the current track and  
display.  
2
appear on the  
To interrupt playback, press 2;.  
M
VCD  
2
will disappear and the current track number will start flashing.  
L
R
To resume playback, press 2; again.  
2. To stop playback, press 9.  
SELECTING A DESIRED TRACK/PASSAGE  
To select a desired track  
Press or § on the set repeatedly (or use digits 0 - 9 buttons or ¡ / on the remote control)  
until the desired track appears on the display.  
If playback is stopped, press 2; to start playback.  
To search for a particular passage during playback  
1. Press and hold or § on the set.  
During searching, the volume will be muted.  
2. When you recognize the passage you want, release the or § button.  
Normal playback resumes.  
For MP3-CD only  
To select a desired album  
On the remote control, press AL+ or AL- until the desired album number appears on the display.  
"AXX" will be displayed.  
On TV screen, the selected album will be highlighted.  
To select a desired track  
Press or § on the set repeatedly (or ¡ / on the remote control) to select a desired track  
from the current album.  
"XXX" will be displayed.  
On TV screen, the selected track will be highlighted.  
Use the digital keys on the remote control to select the track under current album directly.  
To select and playback another track during playback mode  
1. Press or § repeatedly to select another track.  
The new selected track will show on the display screen and TV screen and playback  
continuously.  
For VCD only  
• Either press  
or  
5
or  
6
on the remote control repeatedly to select fast search speed (x1, x2, x3 or x4)  
press & hold or § on the set for 1 second and then release or § to select fast search  
speed (x1). Repeat this step to select other speed (x2, x3, x4).  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD/VCD/MP3-CD  
PROGRAMMING TRACKS  
Up to 20 tracks can be stored in the memory in any order.  
For CD/VCD only  
1. In stop mode, press PROG (or ProG on remote control) to enter programme setting.  
PROG will flash on the display.  
2. Press digits 0 - 9 or ¡ / on the remote control (or / § on the set) to select the desired  
track.  
3. Press PROG to store the select track. The number “PXX“ indicates a programme sequence.“XXX”  
indicates the track number.  
PROG will remain on the display.  
Repeat steps 2 to 3 to store other tracks.  
4. Press 9 to end programme setting.  
Press PROG (or ProG on remote control) in stop mode to review the programme sequence.  
5. Press 2; to play the programmed tracks.  
If you press REPEAT on the set or Rep/RepAll on the remote control during programme playback,  
the current track or all programmed tracks will be played repeatedly.  
REPEAT/REPEAT ALL icon and PROG will appear on the display.  
6. Press 9 in stop mode to clear the programme.  
PROG will disappear from the display.  
Notes : -The programming is automatically cleared as soon as the CD compartment is opened.  
- The function of programme setting is disabled in PLAY/PAUSE mode.  
For MP3-CD only  
1. In stop mode, press PROG on the set (or ProG on the remote control) to enter programme setting.  
PROG will start flashing.  
On TV screen, "PROG" program list (5 lines per page) will be displayed.  
2. Press digits 0 - 9 on the remote control or AL+ - to select the desired album.  
/
3. Press PROG to store the selected album. The number “AXX” represents the album number.  
4. Press / § repeatedly on the set (or digits 0 - 9 or ¡ / on the remote control) to select the  
desired TRACK for programming.  
5. Press PROG to store the selected track.  
PROG will remain flashing on the display.  
Repeat steps 2 to 5 to store other desired album and track.  
6. Press 9 to end programme setting.  
To review programme, press PROG repeatedly in stop mode.  
PXX indicates a programme sequence. AXX indicates an album number. XXX indicates a  
track number.  
7. Press 2; to start programme playback. You can press / § (or ¡ / on the remote control)  
to select the programmed track to play.  
8. Press 9 once to stop programme playback, or twice to clear the programme.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD/VCD/MP3-CD  
SHUFFLE  
You can play all the tracks in random order.  
1. During playing, pause or stop mode, press SHUFF to enable SHUFFLE play mode.  
SHUFFLE will appear on the display.  
2. To exit shuffle mode, press SHUFF again or 9.  
SHUFFLE will disappear from the display.  
Note : - If the Shuffle function is enabled, then the Repeat function is set on, it will disable the  
Shuffle play mode.  
- The shuffle function is not available in the programme playback.  
REPEAT  
You can play the current track or the whole disc repeatedly.  
1. During CD/VCD/MP3-CD playing or pause mode, press REPEAT on the set or Rep/RepAll on the  
remote control.  
REPEAT icon  
- to repeat the current track.  
all- to repeat the whole disc.  
REPEAT ALL icon  
2. To exit the repeat mode, press REPEAT on the set or Rep/RepAll on the remote control until  
the REPEAT/REPEAT ALL icon disappears from the display.  
Notes : - If the Repeat function is enabled, then the Shuffle function is set on, it will disable all  
the Repeat play modes.  
- If the Repeat function is enabled, then the Stop button is pressed, it will disable all the  
Repeat play modes.  
VIDEO CD  
Adjusting the TV System  
Before viewing the Video CD, ensure that the set is switched to corresponding PAL or NTSC system  
of your TV set (exception Multi - system TV).  
1. On the remote control, press NTSC/PAL to switch between NTSC and PAL TV system.  
OSD - On Screen Display  
If you insert VCD/CD, your TV screen will serve as an additional display for messages (e.g. PLAY,  
STOP), and information stored on the VCD/CD.  
Press OSD on the remote control to select viewing various information.  
The current track and current /elapsed time in the track/disc appear on the display.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD/VCD/MP3-CD  
VIDEO CD  
Playing a Video CD with PBC  
PBC (Playback Control) is a predefined play sequence stored on the VCD. PBC feature is only  
available for 2.0 version VCD.  
1. Switch on the TV, then insert a VCD with PBC.  
2. Menu appears on the TV screen. If not, press PBC on the remote control to display Menu.  
If the menu consists of a list of titles, you can select a sequence directly  
1. Press digits 0 - 9 on the remote control to select your choice.  
The VCD starts playing the selected sequence automatically.  
2. Press Return on the remote control to go back to the Menu.  
Note : - If a menu consists of more than one page, press / § (or ¡ / on the remote control)  
to go through the pages.  
Switching off PBC  
Press PBC.  
On TV screen, "PBC OFF" will be displayed shortly.  
Notes : - The menu structure depends on the programme stored on the VCD. Please refer to the  
information supplied with the disc.  
Pause  
1. During playback, press 2; to have a still picture on the TV screen.  
The sound will be muted.  
On TV screen, "PAUSE" will be displayed.  
2. Press 2; again to continue playback.  
Goto  
1. Press GOTO on the remote control.  
On TV screen, "GOTO --:--" will be displayed.  
2. Press digits 0 - 9 on the remote control to key in the disc time from which you want the disc to  
begin playback.  
Notes : - The disc time entered should not be greater than the total disc time.  
- Goto mode is not available whenever PBC mode is switched on.  
Slow  
1. Press Slow on the remote control to watch a VCD at a slower speed. There are 4 types of slow  
modes to select.  
The sound will be muted.  
On TV screen, "SLOW 1/2", "SLOW 1/4", "SLOW 1/8" or "SLOW 1/16" will be displayed.  
2. To resume playback at normal speed, press Slow repeatedly until "PLAY" appears on the TV  
screen or press 2;.  
A-B repeat  
This feature is applicable to audio CD/VCD/MP3-CD, offering to play a certain scene or passage of  
the disc repeatedly.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD/VCD/MP3-CD  
VIDEO CD  
1. Press A-B on the remote control during playback to mark the start point of the chosen scene or  
passage.  
"REPEAT A" will appear on the screen.  
2. Press A-B again to mark the end of the chosen scene or passage.  
"REPEAT AB" will appear on the screen.  
The selected scene or passage will start playing repeatedly.  
3. Press A-B once more to return to normal playback.  
"REPEAT AB" will disappear from the display.  
Notes : - You can also cancel A-B repeat by pressing  
or  
§
(or ¡ / on the remote control).  
- A-B repeat marking can cross from one track to another. But for VCD 2.0, you are only  
able to set the A-B repeat marking within the same track.  
Resume  
In stop mode, press Resume on the remote control to start playback again from where you have  
stopped.  
Note : - Resume will not be available if you have changed the disc, opened the disc tray or  
disconnected the system from the power supply.  
View  
This feature allows you to scan through a VCD for a quick review.  
1. In stop mode, press View on the remote control to go to disc view function.  
On TV screen, up to 9 pictures will be displayed. If a menu consists of more than one page,  
press  
or  
§
(or ¡ / on the remote control) to view the previous/next page.  
The first several seconds of each track will be played.  
To exit review mode, press digits 0 - 9 to play the desired track or 2; to play the current  
selected track.  
2. In playback mode, press View on the remote control to go to track view function.  
press  
or  
§
(or ¡ / on the remote control) to select the track.  
On TV screen, up to 9 pictures within the track will be displayed.  
The first several seconds of each picture will be played.  
To exit review mode, press digits 0 - 9 to play the desired position within the track, or 2; to  
play the current selected position.  
Note : - If the disc is AVCD disc and there're no video tracks on the same viewed page, it cannot  
use the direct digital key to play the track.  
Return  
Press Return on the remote control to return to the previous VCD disc MENU level. It is functional  
only for Video CD when PBC is switched on.  
Audio  
You can use it to select the different audio modes.  
Press Audio on the remote control repeatedly to select the following modes:  
L
L
R
R
on the LCD represents channel left/channel right / dual channel on a bilingual  
VCD or mono left / mono right / stereo on single language VCD.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD/VCD/MP3-CD  
PLAYING A MIXED MODE DISC  
This set can play a mixed mode disc.  
– mixture of audio CD and MP3-CD  
– mixture of other combination may not be operated normally.  
– tracks of CD mode or MP3 mode will normally be played in  
order.  
L
R
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CASSETTE RECORDER  
CASSETTE PLAYBACK  
1. Set the source selector to TAPE/OFF.  
2. Press 9 / to open the cassette holder.  
3. Insert a recorded cassette.  
4. Press 1 and playback will start.  
5. Adjust the sound using the VOLUME and DBB controls.  
6. For brief interruptions, press ;. Press ; again to resume  
playback.  
7. By pressing 5 or 6,fast winding of the tape is possible in  
both directions.  
8. To stop playback, press 9 /  
The keys are automatically released at the end of the tape.  
9. Set the source selector to TAPE/OFF position (with the  
cassette keys released) to switch off the set.  
Note : - During playback, the keys are automatically released at the end of a tape and the set is  
switched off (unless PAUSE mode ; has been activated.)  
- During fast forwarding/rewinding, the keys will not be released at the end of a tape. To  
switch off the set, make sure the cassette keys are also released.  
CASSETTE RECORDING  
General information on cassette recording  
• Recording is permissible insofar as copyright or other rights  
of third parties are not infringed.  
• This deck is not suitable for recording on CHROME (IEC II)  
or METAL (IEC IV) type cassettes. For recording you should  
1
use NORMAL type cassettes (IEC I) on which the tabs have  
not been broken.  
• Check and tighten slack tape before use with a pencil to avoid  
jamming the deck machanism.  
• The recording level is set automatically.  
Note : - No recording will take place during the 7 seconds in the  
beginning of the tape.  
• To prevent the accidental erasure of a recording, keep the cassette side to be safeguarded in  
front of you and break out the left tab. Recording on this side is no longer possible.  
The making of unauthorized copies of copy-protected material, including computer  
programmes, files, broadcasts and sound recordings, may be an infringement of  
copyrights and constitute a criminal offence.  
This equipment should not be used for such  
purposes.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CASSETTE RECORDER  
RECORDING FROM THE RADIO  
1. Set the source selector to TUNER.  
2. Adjust BAND to FM or MW.  
3. Tune to the desired radio station using the TUNING knob.  
4. Press 9 / to open the cassette holder.  
5. Insert a blank tape.  
6. Press 0 to start recording.  
7. For brief interruptions, press ;. To resume recording,  
press ; again.  
8. To stop recording, press 9 /.  
SYNCHRO START CD RECORDING  
1. Set the source selector to CD.  
2. Insert a CD and if desired, programme track numbers.  
3. Press 9 / to open the cassette holder.  
4. Insert a blank cassette.  
5. Press 0 to start recording.  
Playing of the CD programme starts automatically from the  
beginning of the programme.  
6. For brief interruptions, press ;. To resume recording,  
press ; again.  
7. To stop recording press 9 /  
To select and record a particular passage within a track  
1. Press and hold or § on the set to select a passage.  
2. Put the CD player in position at the selected passage.  
;
Recording will start from this exact point when you press 0.  
3. Press 2; to start recording.  
TAPE DECK MAINTENANCE  
To ensure a good recording and playback of the tape deck, clean  
parts A,B and C show in the diagram below, after approx. 50 hours of  
operation, or on average once a month. Use a cotton bud slightly  
moistened with alcohol or a special head cleaning fluid to clean the deck.  
C
B
A
A
• Open the cassette holder by pressing 9 /  
.
• Press 1 and clean the rubber pressure rollers C.  
• Press ; and clean the magnetic heads A and also the capstans B.  
• After cleaning, press 9 /  
.
Cleaning of the heads can also be done by playing a cleaning cassette through once.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
PRECAUTIONS & GENERAL MAINTENANCE  
• Place the set on a hard, flat surface so that the system does not tilt.  
• Where the Mains plug or an appliance coupler is used as the  
disconnect device, the disconnect device shall remain readily operable.  
• Always shut the CD door to keep the CD compartment dust-free. To  
clean the dusted compartment with a soft dry cloth.  
• The mechanical parts of the set contain self-lubricating bearings and  
must not be oiled or lubricated.  
• To clean the set, use a soft, slightly dampened chamois leather. Do not  
use any cleaning agents containing alcohol, ammonia, benzene or  
abrasives as these may harm the housing.  
Do not expose the system, batteries or discs to humidity, rain,  
sand or excessive heat (caused by heating equipment or direct  
sunlight). Always keep the disc tray closed to avoid dust on the  
lens.  
No objects filled with liquids, such as vases, shall be placed on the apparatus.  
• The apparatus shall not be exposed to dripping or splashing.  
• Adequate ventilation with a minimum gap of 15 cm between the ventilation holes and surrounding  
surfaces is necessary to prevent heat build-up.  
• The ventilation should not be impeded by covering the ventilation openings with items, such as  
newspapers, table-cloths, curtains, etc.  
• No naked flame sources, such as lighted candles, should be placed on the apparatus.  
CD PLAYER AND CD HANDLING  
• The lens of the CD player should never be touched.  
• Sudden changes in the surrounding temperature can cause  
condensation to form and the lens of your CD player to cloud over.  
Playing a CD is then not possible. Do not attempt to clean the lens but  
X
leave the set in a warm environment until the moisture evaporates.  
• Use only Digital Audio CDs.  
• To take a CD out of its box, press the centre spindle while lifting the  
CD. Always pick up the CD by the edge and replace the CD back in its  
box after use to avoid scratching and dust.  
• To clean the CD, wipe in a straight line from the centre towards the  
edge using a soft, lint-free cloth. Do not use cleaning agents as they  
may damage the disc.  
Never write on a CD or attach stickers to it.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
If a fault occurs, first check the points listed below before taking the set for repair.  
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.  
WARNING: Do not open the set as there is a risk of electric shock. Under no  
circumstances should you try to repair the set yourself, as this will  
invalidate the guarantee.  
Problem  
Solution  
CD/VCD OPERATION  
"NO" is displayed  
Insert a disc.  
Check if the disc is inserted upside down.  
Wait until the moisture condensation at the lens has  
cleared.  
Replace or clean the disc, see "Maintenance"  
Use a readable disc or correct recorded format  
MP3-CD.  
No picture on TV screen  
No colour on TV  
Connect the cable between the system and TV.  
Change the system to the respective PAL or  
NTSC setting.  
RADIO RECEPTION  
Radio reception is poor  
If the signal is too weak, adjust the antenna  
for better reception.  
Increase the distance between the Receiver  
and your TV or VCR.  
TAPE OPERATION/RECORDING  
Recording or playback cannot be made  
Clean deck parts, see "Maintenance".  
Use only NORMAL (IEC I) tape.  
Apply a piece of adhesive tape over the missing  
tab space.  
GENERAL  
The system does not react when buttons Slide the source sector to TAPE/OFF. Remove and  
pressed/set does not work/no display on  
LCD.  
reconnect the AC power plug for 30 seconds and  
switch on the set again.  
Sound cannot be heard or is of poor  
quality  
Adjust the volume.  
Make sure the MP3-CD was recorded within  
32-320 kbps (128kbps preferably) with sampling  
frequencies at 8 - 48 kHz (44.1kHz preferably).  
The remote control does not function  
properly  
Reduce the distance between the remote control  
and the system.  
Insert the batteries with their polarities (+/- signs)  
aligned as indicated.  
Replace the batteries.  
Point the remote control in the direction of the  
system's IR sensor.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Meet Philips at the Internet  
W
AZ5160  
CLASS 1  
LASER PRODUCT  
Printed in China  
PDCC-ZH/ZC-0731  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pfaff Sewing Machine expression 20 User Manual
Philips DVD Player DVD622 User Manual
Philips Portable DVD Player PET831 12 User Manual
Philips Work Light P 2220 E User Manual
Pioneer DVD Player DV LX50 User Manual
Pioneer Home Theater System S GX3V User Manual
Polycom Telephone CX200 User Manual
Polycom Webcam HA7250QT4 User Manual
Precision Power Car Stereo System DCX 730 User Manual
PYLE Audio DVD Player PLTDF25 User Manual