Pentair Swimming Pool SunLite LTC User Manual

®
SunLite LTC  
Small Underwater Pool Lights  
O W N E R ’ S M A N U A L  
INSTALLATION, OPERATION & PARTS  
This manual should be furnished to  
the end user of this light; its use will  
reduce service calls and chance of  
injury and will lengthen light life.  
Pentair Water Pool and Spa, Inc.  
1620 Hawkins Ave., Sanford, NC 27330 • (800) 831-7133 or (919) 566-8000  
10951 West Los Angeles Ave., Moorpark, CA 93021 • (800) 831-7133 or (805) 553-5000  
S715 (Rev. A 10/29/07)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
READ AND FOLLOW  
Burn hazard. Never operate this light fix-  
ture for more than 10 seconds unless it is completely  
submerged in water. This fixture requires total submer-  
sion for cooling.  
SAFETY INSTRUCTIONS!  
This is the safety alert symbol. When you see this  
symbol in this manual, look for one of the follow-  
ing signal words and be alert to the potential for personal  
injury.  
Breakage hazard. Install fixture in a vertical  
pool or spa wall – not in floor. Failure to install the fix-  
ture properly could result in personal injury and/or prop-  
erty damage. Do not push off from the poolside against  
the light.  
warns about hazards that will cause serious  
personal injury, death or major property damage if  
ignored.  
Except when the fixture is installed in an area of the  
swimming pool that is not used for swimming and the  
lens is adequately guarded to keep any person from con-  
tacting it, the fixture shall be installed in or on a wall of  
the pool, with the top of the lens opening not less than  
18" below the normal level of the pool.  
warns about hazards that can cause serious  
personal injury, death or major property damage if  
ignored.  
warns about hazards that will or can cause  
minor personal injury or property damage if ignored.  
Locate junction box at least 8" above maximum water  
level and not less than 4 feet from the perimeter of the  
pool.  
The label NOTICE indicates special instructions which  
are important but not related to hazards.  
Carefully read and follow all safety instructions in this  
manual and on equipment.  
The junction box must be located:  
• at least 4’ from the perimeter of the pool (unless sepa-  
rated from the pool by a solid fence, wall or other  
permanent structure,  
• at least 8" above maximum water level,  
• at least 4" above the deck or ground level.  
End user should save these instructions.  
GENERAL SAFETY!  
Hazardous voltage. Incorrectly installed or  
tested equipment may fail, causing severe injury or prop-  
erty damage. Read and follow instructions in owner's  
manual when installing and operating equipment.  
Installation and maintenance of this circuit, the light, light  
niche, and any other accessories attached to the circuit,  
must be performed by a licensed electrician.  
Make sure that the installation is in compliance with  
local codes, the NEC, and the CEC, as applicable. See  
Figure 1, Page 5.  
The improper use of Ozone generators, Chlorine genera-  
tors, Copper/Silver Ion generators or certain chemicals  
for water purification may cause damage to the fixture.  
When such water purification methods are used, be sure  
to monitor the water conditions. Subjecting the fixture to  
extreme conditions or harsh environments may cause  
corrosion and premature failure of the fixture or its  
components.  
The complete electrical system must be installed, tested,  
and approved by a licensed electrician before it is placed  
in operation. Failure to have this product installed by a  
licensed professional will void the product warranty.  
Risk of electrical shock. Before removing  
fixture from pool wall, ALWAYS TURN OFF THE POWER  
at the breaker.  
Cutting hazard if light is improperly  
installed. This light is for use only in commercial and  
residential swimming pools and spas. It has not been  
designed, tested, or approved for use in wave pools,  
lazy rivers, or other waterpark features, and should not  
be used in them. Use in any application other than a  
swimming pool or spa may lead to damage to the light  
and cuts to swimmers and will void the warranty.  
Sta-Rite will not be responsible for any damages or  
injuries due to misapplication of this light.  
All 12 Volt lamps require the installation of a 12 Volt  
transformer.  
This light and its light niche must be installed in accor-  
dance with Article 680 of the National Electrical Code  
(NEC), in the United States, or Section 68 of the Canadian  
Electrical Code (CEC), as applicable, and all local code  
requirements.  
Install an approved Ground Fault Circuit Interrupter in  
the electrical circuit for this light.  
All devices in the system must be directly grounded to a  
positive electrical ground. All devices in the system must  
meet all applicable code requirements for bonding.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
Table I  
®
SunLite LTC Small Underwater Pool Lights  
with Stainless Steel Face Ring  
Allowance of Watts/Sq. Foot  
of Pool Area  
Type of Pool  
Model No.  
Cord Length in Feet (m)  
Small Residential Pools  
(Less than 800 sq. ft.)  
Large Public Pools  
Diving Pools  
(Less than 12 ft. deep)  
Diving Pools  
12V - 75 Watts  
05603-2030  
05603-2050  
05603-2100  
1/2 to 1*  
1 to 1 2  
30 (9.1)  
50 (15.2)  
100 (30.5)  
1
1
1 ⁄2 to 2  
120V - 100 Watts  
05605-2030  
(12 to 20 ft. deep)  
Competition Pools  
2 to 3  
2 to 3**  
30 (9.1)  
50 (15.2)  
100 (30.5)  
05605-2050  
05605-2100  
* One 500 watt light at deep end of pool is recommended.  
** For competition pools:  
120V - 250 Watts  
05607-2030  
1. Make sure that the start/finish ends of lanes are well  
lighted.  
30 (9.1)  
50 (15.2)  
100 (30.5)  
05607-2050  
05607-2100  
2. Never install lights in end walls at end of swimming  
lanes. However, if short course racing is provided across  
width of a 50 meter course, light fixtures may be  
installed between lanes (under racing lines) on a seperate  
switch.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Make connections in the conduit box (be sure to fol-  
low code requirements!). Connect the supply circuit  
grounding wire (green, green and yellow, or bare  
copper) to the green ground conductor from the light  
fixture. Connect the line supply wire (the black or  
’hot’ wire) to the black wire from the light fixture.  
Connect the neutral (white) supply wire to the neutral  
(white) wire from the light fixture.  
INSTALLATION  
®
SunLite LTC Lamp Housing Installation  
(Refer to Figure 1, below)  
Burn hazard. This light should never be  
energized while laying face down on the pool deck.  
Installation of a 12 Volt transformer is required when  
installing the 12 Volt model of this light. The transformer  
must be located:  
4. Coil the remaining cord in the back of the niche and  
place the lamp housing in the niche. The mounting  
tab on the bottom of the lamp housing must be in the  
notch at the bottom of the niche.  
• at least 10’ from the pool wall,  
• installed near a grounded, 3-prong, 120V, GFCI  
protected outlet. If you do not have a GFCI protected  
outlet, have a qualified electrician install one.  
5. Fasten the lamp housing into the niche with the  
captive leader screw at the top of the lamp housing  
(use a No. 2 Phillips screwdriver). Tighten this screw  
securely (20 inch-pounds torque) to insure good  
electrical bonding.  
Do not use a 3-prong adapter. The adapter voids the  
grounding of the system.  
Do not cut the grounding pin.  
NOTICE: The leader screw in the face ring may be  
recessed.  
Do not use an extension cord! Purchase a light with a  
longer cord.  
NOTE: Do not try to loosen the strain relief (cord nut) on  
the back of the lamp housing; the cord is not detachable  
from the lamp housing. Attempting to loosen the strain  
relief will damage the lamp housing assembly, void the  
warranty and may cause an electrical shock hazard if the  
pool bonding is not connected and functioning correctly  
(see “General Safety”, Page 2).  
1. Be sure the power is off.  
2. Place lamp housing on the deck above the niche.  
Feed the cord through the back of the lamp housing  
and to the conduit box. Make sure that there is  
enough cord to allow the fixture to be placed on the  
deck for re-lamping.  
Junction box  
4 Ft. Min.  
To  
service  
Fixture removed  
for relamping  
Max. water  
level  
8” Min.  
8” Min.  
Low level  
probe  
18” Min.  
Fixture  
To service  
Brass conduit  
To fixture  
Sufficient cord to allow fixture to  
be put on the deck for relamping  
Pool wall  
Figure 1: Lamp Housing Installation  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. To close the fixture, make sure the clamp ring is open  
to about 4 inches and that the nut is at the end of the  
leader screw.  
Lamp Installation Instructions (Re-lamping)  
See Figure 2, Page 7, for Key numbers.  
1. Be sure that the power is off. Allow the lamp to cool  
before relamping.  
7. Lay the face ring face down on a flat surface.  
Carefully align the clear lens (Key No. 4) and lens  
gasket (Key No. 5) over the flanged hole in the face  
ring (key No. 2), with the word “top” on the lens  
lined up with the leader screw on the face ring. The  
silver tape should be on top and the arrow pointing  
toward the lamp.  
2. Remove the leader screw (Key No. 1) from the face  
ring and lift the lamp housing up and out of the  
niche.  
3. Loosen the screw and nut on the clamp ring assembly  
(Key No. 5) until the nut is near the end of the screw.  
Swing the screw and nut out of the forked slot of the  
clamp ring assembly and bend the clamp ring open  
to about 4 inches.  
8. Align the lamp housing over the lens gasket with the  
word “top” inline with the leader screw in the face  
ring.  
4. To relamp 120V model, remove the lamp by turning  
it counterclockwise and pulling it straight out.  
Replace with an equivalent lamp. For the 12V model,  
remove the lamp by pulling it straight out while hold-  
ing the spring clip back (away from the socket).  
Replace with an equivalent lamp.  
9. Position one half of the clamp ring around the metal  
flanges of the face ring and lamp housing.  
10.Close the clamp ring, fitting the other half over the  
same flanges.  
11. Swing the nut and screw into the slotted end of the  
clamp assembly. Tighten this screw securely (20 inch-  
pounds torque) to insure good electrical bonding.  
5. Using a clean soft lint free cloth, carefully wipe all  
sealing surfaces on the lamp housing and lens.  
12.To replace the lamp housing in the pool wall hook  
the bracket at the bottom of the niche and tighten the  
leader screw on the face ring of the lamp housing.  
NOTE: Do not touch the lamp with your bare fingers. If  
contact occurs, clean the lamp glass with alcohol and a  
clean cloth.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
6
5
4
3
2
Note gasket orientation.  
1
®
Figure 2 – SunLite LTC Lamp Exploded View  
®
REPAIR PARTS LIST – SUNLITE LTC LAMPS  
Key  
No.  
05603 Series  
12V, 75W  
05605 Series  
120V, 100W  
05607 Series  
120V, 250W  
Part Description  
Leader Screw*  
Face Ring, SS, Assy Kit  
Rubber Retainer for Leader Screw*  
Clear Lens, Kit  
Gasket, Lens  
Clamp Ring Assembly  
Lamp Housing  
Lamp, 100W, 120V, Halogen, T-4 MC  
Lamp, 75W, 12V, Halogen, MR 16  
Lamp, 250W, 130V, Halogen, T-4 MC  
Replacement Screw Kit  
Qty.  
1
2
3
4
5
6
7
1
1
1
1
1
1
1
1
1
1
1
-
-
-
05601-0001  
05601-0005  
34620-0002  
05601-0014  
05601-0006  
05601-0001  
05601-0005  
34620-0002  
05601-0014  
05601-0006  
79102900  
-
-
05601-0001  
05601-0005  
34620-0002  
05601-0014  
05601-0006  
-
-
-
79112400  
-
05601-0101  
79113800  
05601-0101  
05601-0101  
† Not sold separately.  
• Not illustrated.  
* Included with Replacement Screw Kit.  
SAVE THESE INSTRUCTIONS  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
© 2007 Pentair Water Pool and Spa, Inc. All rights reserved.  
1620 HawkinsAve., Sanford, NC 27330 • (800) 831-7133 or (919) 566-8000  
10951 W. Los Angeles Ave., Moorpark, CA 93021 • (800) 831-7133 or (805) 553-5000  
This document is subject to change without notice.  
S715 (Rev. A 10/29/07)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peavey Stereo Amplifier XR 600B User Manual
Philips Bottle Warmer SCF131 17 User Manual
Philips Electric Shaver 6705X User Manual
Philips Flat Panel Television BDL6520 User Manual
Philips Remote Starter Remote Starter User Manual
Philips Router PRT 150 User Manual
Philips Stereo Amplifier BGA6489 User Manual
Philips Stereo System SWA2083 User Manual
Philips Work Light P 2543 C User Manual
ProForm Treadmill 831295230 User Manual