I N S T A L L A T I O N
Endura™ KBD5000
Series Keyboard
C1620M-B (9/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Rear Panel Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Installing the Wrist Support and Control Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Rotating the Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Overview of VCD5000 Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
List of Illustrations
1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2 Product Serial Number Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3 Rear Panel Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
4 Installing the Wrist Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
5 Installing the Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
6 Connecting the KBD5000 to a VCD5000 or a WS5050 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
7 Keyboard Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
List of Tables
C1620M-B (9/05)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.” This
booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this
equipment under Federal Communications Commission’s rules.
In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved
equipment or unshielded cables is likely to result in interference to radio and television reception.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
4
C1620M-B (9/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
The KBD5000 Series keyboard is the controller for Pelco’s network-based video system products. It is the point from which all user functions can
be accessed.
The KBD5000 Series is configured with three control modules that are installed in receptacles on the keyboard base. Modules can be placed into
any receptacle, creating a customized keyboard for operation with either the left or right hand.
The following three modules are included with the base:
•
•
•
A variable speed, vector-solving joystick with keys for lens iris and focus control. The barrel-type joystick provides precise pan and tilt
control of fixed speed and variable speed positioning systems. Twisting the joystick zooms the lens in and out. The joystick and button atop
the joystick also are used for navigating the on-screen programming menus.
A jog dial/shuttle ring for playback and menu navigation. The jog/shuttle contains four illuminated function keys. Each key’s color
corresponds to the color of its icon displayed on the monitors linked to the user interface. This intuitive color matching design lets users
navigate the on-screen menus without looking down to read keyboard text labels.
A keypad for camera and monitor control. Keys select cameras and monitors, and the number of cameras to view.
The KBD5000 Series can be logically configured so any number of keyboards can be added to the system. When combined with Pelco’s new user
interfaces (UIs), network video recorders (NVRs), and encoders, the KBD5000 forms an integral part of a complete network-based video control
system.
The KBD5000 is connected to a USB port on the VCD5000 virtual console display. Together this pair provides all the traditional user keyboard
functionality as well as full access to network-based operations and settings. The keyboard lets the user access operational functions displayed
as semitransparent graphical overlays on the monitor screen.
PARTS LIST
Qty Description
1
3
Keyboard base
Modules
3
1
Special security screws
Special security bit
1
Wrist support
Screws
4
1
3
1
1
Power supply
Power cords (1 USA standard, 1 UK standard, 1 European standard)
USB Type B-to-Type A cable with screw attachment; 16.4 ft (5.0 m) long
KBD5000 Installation/Operation manual
C1620M-B (9/05)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PACKAGE CONTENTS
ACCESSORY PACK
USA STANDARD
POWER CORD
(110 VAC)
JOG/SHUTTLE MODULE
POWER SUPPLY
AND USB CABLE
1 EA.
1 EA.
1 EA.
SECURITY BIT
KEYBOARD BASE
1 EA.
1 EA.
KEYPAD MODULE
EUROPEAN
STANDARD POWER
CORD (220 VAC)
1 EA.
1 EA.
WRIST SUPPORT
1 EA.
SHOWN ACTUAL SIZE
BUTTON
HEAD SCREW
10-32 3/8-INCH
3 EA.
PHILLIPS PAN
HEAD SCREW
4-40 X .312-INCH
4 EA.
UK
SAFETY INSTRUCTIONS
STANDARD POWER
CORD (250 VAC)
1 EA
JOYSTICK MODULE
AND MANUAL
1 EA.
Figure 1. Package Components
PRODUCT SERIAL NUMBER LABEL
A label citing your unit’s product serial number is attached to the bottom of your KBD5000 keyboard base. Should your unit require service, the
product serial number label helps Pelco product support personnel identify your system and its factory configuration.
Model
MODEL
03267-39-0020
SN
FREQ
50/60HZ
AMPS
Sample Text
VOLTS
Sample Text
REV
Sample Text
Audio/Video Apparatus
91KK
MFG BY PELCO, CLOVIS, CA MADE IN USA
Figure 2. Product Serial Number Label
6
C1620M-B (9/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel Connectors
ᕥ
ᕡ ᕢ ᕢ ᕣ
ᕤ
Figure 3. Rear Panel Connectors
ᕡ
ᕢ
ᕣ
ᕤ
ᕥ
Input power
USB Type A port
USB Type B port (Attaches to a VCD5000 or Endura Workstation [WS5000 Series]; use the supplied Type B-to-Type A adapter cable.)
Headphone connector/speaker
Microphone connector
NOTES:
•
•
Any USB cable attached to the keyboard must be no longer than 16.4 feet (5.0 m).
You can use the USB ports to export video, clips, or still images. To do so, the port must be connected to a USB hard drive or USB memory key.
USB CD drives and DVD drives are not supported.
C1620M-B (9/05)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
INSTALLING THE WRIST SUPPORT AND CONTROL MODULES
The KBD5000 comes with three control modules that fit in three receptacles on the base. You can choose which module will be located in which
receptacle, and each module can be rotated 60 degrees in each receptacle. The KBD5000 also has a wrist support that can be easily installed
and removed. This system allows custom tailoring of the keyboard to your preferences.
A suggested setup is to install the jog/shuttle module on the left side of the base, the keypad module in the center, and the joystick module on
the right.
To install the wrist support and modules, do the following:
1. Remove the base, wrist support, and modules from their packaging.
2. If you want to use the wrist support, do the following (although the keyboard can be used without the wrist support). Refer to Figure 4.
Turn the keyboard upside down. Attach the wrist support by first lining up the four tabs on the wrist support with the four matching screw
receptacles on the base. Install the four supplied screws (Phillips pan head 4-40 x 0.312-inch). Turn the base face up.
Figure 4. Installing the Wrist Support
8
C1620M-B (9/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Refer to Figure 5. Select a module. Each receptacle on the base has an attached USB cable. Turn the module upside down. Plug the USB
connector cable into the USB port on the bottom of the module. Thread the USB connector cable through the plastic strain reliefs on the
module to hold the cable in place.
Figure 5. Installing the Modules
4. Refer to Figure 5. Turn the module upright so its top faces the rear of the base. (The rear of the base is the side with the connectors.)
Wind the cable clockwise around the base of the module, making sure to tuck any extra cable back into the hole in the receptacle.
WARNING: Pinching the cable can result in damage.
Being very careful not to pinch the cable, insert the module into the receptacle.
5. Holding the module in the receptacle, turn the base on its side. Insert the special security screw (supplied) through the bottom of the base
and into the bottom of the corresponding module. Tighten with the special security bit (supplied).
6. Repeat steps 3 through 5 for the other two modules.
ROTATING THE MODULES
WARNING: Rotating the module with a pinched cable can damage the cable.
The KBD5000 lets you rotate each module to a position most comfortable for you. Each module can be rotated in its receptacle by pushing with
your fingers against the raised plastic tabs on the module.
C1620M-B (9/05)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE KEYBOARD
To hook up the KBD5000, connect the USB Type B-to-Type A cable (supplied) from the USB connector on the rear of the KBD5000 to the USB
connector on either the front or rear of the Pelco VCD5000 virtual console display or to the USB connector on an Endura Workstation (WS5000
NOTE: Any USB cable attached to the keyboard must be no longer than 16.4 feet (5.0 m).
VCD5000 FRONT (BEZEL OFF)
OR
VCD5000 REAR
OR
WS5050 FRONT (BEZEL OFF)
OR
WS5050 REAR
Figure 6. Connecting the KBD5000 to a VCD5000 or a WS5050
TURNING ON THE POWER
To apply power, first insert the power supply’s attached cord into the back of the keyboard and tighten the connector barrel. Then, insert the
appropriate supplied power cord (USA standard, UK standard, or European standard) into the power supply. Finally, insert the power cord’s plug
into a properly grounded power socket. When power is applied, lights on the modules illuminate.
10
C1620M-B (9/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
The following is only a simple guide. For details on operating the KBD5000, refer to the Pelco VCD5000 Virtual Console Display Operation
manual, C1618M.
KEYS
ᕡ
ᕢ
ᕥ
ᕦ
ᕫᕵ
ᕫᕶ
ᕣ
ᕤ
ᕧ ᕨ ᕩ ᕫᕾ ᕧ
ᕫᕷ ᕫᕸ
ᕫᕹ
Figure 7. Keyboard Keys
Table A. KBD5000 Key Functions
Description
Reference Number
Module
ᕡ
ᕢ
ᕣ
ᕤ
ᕥ
ᕦ
ᕧ
ᕨ
ᕩ
ᕫᕾ
ᕫᕵ
ᕫᕶ
ᕫᕷ
ᕫᕸ
ᕫᕹ
Camera selection key
Keypad (numbers 0 through 9)
Multiple view keys
Keypad
Monitor selection key
Color function keys (correspond to screen menus)
Record video key
Menu selection keys
Jog/Shuttle
Joystick
Play/pause video key
Jog/shuttle
Live/Playback mode key
Joystick with Enter button on top
Iris key (works in conjunction with joystick)
Help key
AUX key
Focus key (works in conjunction with joystick)
NOTE: Not all functions are possible if the keyboard is connected to an Endura Workstation (WS5000 Series).
C1620M-B (9/05)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERVIEW OF VCD5000 MENUS
The KBD5000 works in conjunction with the VCD5000 virtual console display and its menus.
•
•
•
To display the on-screen menu, press either Menu key on the jog/shuttle module.
To hide the menu, press either Menu key on the jog/shuttle module.
There are two ways to navigate within a menu and select an item.
(1) Joystick
Use the joystick to navigate within a menu and click the button atop the joystick to select an item.
(2) Quick Keys
The keyboard contains four illuminated function keys. Each key’s color corresponds to the color of its icon displayed on the monitors
linked to the VCD5000. This color-matching design lets you navigate the on-screen menus without looking down to read keyboard text
labels.
To navigate to the next level in a menu or to select an item, click the colored key that corresponds to the on-screen menu item.
For example, to select the cyan icon on the screen, press the cyan key.
After you press a key or the button atop the joystick, the program either presents another set of menus or a screen of settings.
To access Help, click the Help icon or press the Help key on the joystick module.
•
12
C1620M-B (9/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If the following instructions fail to solve your problem, contact Pelco Technical Support for help at 1-800-289-9100, or 1-559-292-1981 if calling
internationally. You should have the serial number from the bottom of the keyboard ready in case it is needed.
Do not try to repair a keyboard yourself. Opening it immediately voids any warranty. Leave maintenance and repairs to qualified technical
personnel. Swap a defective unit with a replacement unit and return the defective one for repair.
Problem
Action
The cable may be pinched between the module and receptacle. Remove the module. Wind the cable about the
base of the module and push any excess through the hole in the receptacle. Hold the cable in place on the
module as long as possible while placing the module in the receptacle.
Module will not fully seat
in receptacle.
Module will not rotate.
The cable may be pinched between the module and receptacle. Perform the action above.
C1620M-B (9/05)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
POWER SUPPLY
Input Voltage
100-240 VAC, 50/60 Hz
12 VDC
Output Voltage
Power Output
20 W
Input Connector Type
Output Connector Type
Cable Type
Universal, interchangeable
2.5 mm screw-on barrel
Supplied with grounded power cord; molded connector, 3 prongs, 6 ft (1.8 m); 1 USA standard (110 VAC),
1 European standard (220 VAC), 1 UK standard (250 VAC)
KEYBOARD BASE
Keyboard Interface
Cable
USB 2.0
USB, captive, 16.4 ft (5.0 m)
Input Voltage
Input Current
12 VDC
1.3 A (maximum)
Upstream Port
Downstream Ports
Audio Output
Audio Input
USB 2.0 (USB Type B connector)
Two USB 2.0 Hi/Full/Low speed (USB Type A connector)
Embedded speaker or plug-in headset, 0.5 watts into 8-ohm load per channel
Plug-in microphone, mono (30-350 mVp-p), or line input, stereo (0.35-2.0 Vp-p)
KEYBOARD MODULES
Keyboard Keypad
Joystick
0-9 keys, camera, monitor, and multiple view keys
Fully proportional pan and tilt, variable speed; with zoom, iris, and focus controls
Jog/Shuttle
Proportional, fast forward, reverse, and video transport.
Menu navigation on VCD5000 virtual console display.
Module Connectors
Three (one for each module), USB 1.1 mini USB
GENERAL
Dimensions
Without Wrist Support
7.86" D x 14.78" W x 4.6" H
(19.96 x 37.54 x 11.68 cm)
9.94" D x 16.88" W x 4.6" H
(25.25 x 42.88 x 11.68 cm)
With Wrist Support
Unit Weight (without wrist support) 2.68 lb (1.22 kg)
Unit Weight (with wrist support)
Shipping Weight
3.32 lb (1.51 kg)
5 lb (2 kg)
ENVIRONMENTAL
Operating Temperature
Storage Temperature
Operating Humidity
32° to 104°F (0° to 40°C)
32° to 176°F (0° to 80°C)
Up to 96%
14
C1620M-B (9/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
Exceptions to this warranty are as noted below:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
•
•
•
Three years on PMCL 200/300/400 Series LCD monitors.
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
RETURNS
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays.
The lamp and color wheel will be covered for a period of 90 days. The air filter is not
covered under warranty.
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).
•
•
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
•
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, Endura™ Series distributed network-based video products, and TW3000 Series
twisted pair transmission products.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
REVISION HISTORY
Manual #
C1620M
C1620M-A
C1620M-B
Date
10/04
4/05
Comments
Original version.
In the specifications, included dimensions and weight for a unit with the wrist support.
Revised the parts list to include a UK power cable, and moved the parts list to page 4. Added a package contents drawing, which became the new Figure 1. Added
the cable type to the specifications page. Revised Figure 6.
9/05
Pelco, the Pelco logo, Spectra, Genex, Legacy, Coaxitron, Esprit, and Camclosure are registered trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.
©Copyright 2005, Pelco. All rights reserved.
DLP is a registered trademark of Texas Instruments, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
ISO9001
United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East
|
|
|
|
|
|
|
|
Download from Www.Somanuals.com. All Manuals Search And Download.
|