®
MPT24DT, MPT115DT, and
MPT220DT Series
Pan/Tilt Controls
Installation/Operation Manual
C520M Rev B (6/92)
1.0 WARNINGS
2.0 SCOPE
Prior to installation and use of this product, the follow-
ing WARNINGS should be observed.
The information contained within this manual covers
the installation and operation of the MPT24DT,
MPT115DT, and MPT220DT Series Pan/Tilt Controls.
1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.
3.0 DESCRIPTION
The MPT24DT and MPT115DT Series controls are
designed to provide control for Pelco 24 VAC, 120 VAC,
and 230 VAC pan/tilts. Pan/tilt movement is controlled
by an eight position joystick (up, down, left, right and
simultaneous combinations of pan/tilt functions when
move diagonally).
2. Unless the unit is specifically marked as a NEMA
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is de-
signed for indoor use only and it must not be in-
stalled where exposed to rain and moisture.
3. Use only installation methods and materials ca-
pable of supporting four (4) times the maximum
specified load.
In addition to manual control and continuous auto scan
operations, the MPTA24DT and MPTA115DT offer the
revolutionary new random scan feature available only
from Pelco. Random scan is a significant advance in
CCTV security/surveillance protection that makes con-
tinuous duty auto scan operations virtually obsolete.
4. Only use replacement parts recommended by
Pelco.
Please thoroughly familiarize yourself with the infor-
mation in this manual prior to installation and opera-
tion.
(800) 289-9100 or (1-559) 292-1981 • FAX (800) 289-9150 or (1-559) 292-3827
International customers call (1-559) 292-1981 or FAX (1-559) 348-1120
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0 INSTALLATION
4. The contact pins supplied with the mating connec-
tor are the “crimp” type which may also be sol-
dered if you so desired (item 4).
4.1 CONNECTOR ASSEMBLY
Installation and/or testing will require you to assemble
the connector parts provided. Fabricate the intercon-
necting cable according to the following steps (refer-
ence Figure 1).
5. After crimping or soldering the contact pins to the
conductors, push them into the proper holes in the
connector until they snap in place.
NOTE: Contacts cannot be removed from the
connector without the use of the appropriate
AMP extraction tool which is available from
Pelco.
1. Slide partAof the cable clamp (item 1) over the end
of the cable (item 1, part C) with the threaded end
of the cable clamp facing the connector (item 5).
2. If the cable has a diameter less than 1/2 inch (1.3
cm), slide the rubber boot (item 2) over the end of
the cable and pull through the cable clamp to so
that the boot encases the cable and forms a good
seal.
6. Slide partA of the cable clamp toward the connec-
tor and screw the parts together.Attach part B (item
1) onto part A and connect both parts with the
screws provided.
7. Connect the cable assembly to the unit and seat
the connector by twisting the locking collar until it
snaps into position.
3. Strip back the cable jacket approximately 1-1/4
inches (3.2 cm) and separate the individual con-
ductors (item 3).
5
1
threaded end of
cable clamp
A
B
C
STEP 1
FLEXIBLE RUBBER BOOT
5
1
A
B
STEP 2
C
2
5 **
3
1
4
A
B
STRIP 1/8"
C
STEPS 3-7
CRIMP
CRIMP
WIRE
INSULATION
OUTSIDE
JACKET
STRIP 1"
OF CABLE
4
1
2
1
1
**
3
8
9
5
ITEM 5 DETAIL
4
6
15
10
16
23
3
9
14
22
28
10
15
21
20
25
28
7
33
14
11
29
37
34
26
16
15
FRONT VIEW
FRONT VIEW
FRONT VIEW
37-PIN CONNECTOR
28-PIN CONNECTOR
16-PIN CONNECTOR
3
1
3
1
4
7
4
6
THE MOST COMMONLY USED
CONNECTOR PIN-OUT CONFIG-
URATIONS ARE SHOWN HERE.
REFERENCE THE CONNECTOR
DRAWING APPLICABLE TO
YOUR SITUATION.
11
8
9
7
14
12
FRONT VIEW
9-PIN CONNECTOR
FRONT VIEW
14-PIN CONNECTOR
Figure 1. Connector Assembly
Pelco Manual C520M Rev B (6/92)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL
PAN/TILT
1
3
P/T COMMON
LEFT
1
3
5
1
3
2
1
4
2
5
3
6
4
8
5
9
6
7
5
6
7
8
DOWN
10 11
UP
6
7
7
8
9
12 13 14
RIGHT
8
9
SAFETY GROUND
FRONT VIEW
FRONT VIEW
14
14-PIN
PLUG
9-PIN
PLUG
Figure 2. Wiring Diagram
4
Pelco Manual C520M Rev B (6/92)
Download from Www.Somanuals.com. All Manuals Search And Download.
5.0 OPERATION AND SYSTEM TEST
5.1 MANUAL OPERATION TEST
The MPTA24DT, MPTA115DT, and
MPTA220DT are factory preset for a duty
cycle of 50%. However, Random Scan dwell
time is adjustable by installation or removal
of diodes CR9, 10 and 11 on PCB1500530.
Table A shows the available duty cycle com-
binations.
After installing the interconnecting cable between the
pan/tilt and control, plug the control into theAC outlet,
turn control on, and test operation using the following
procedures:
c. At the completion of a dwell period, another
scan period is started. The direction of this scan
period is also randomly determined.
1. Move the joystick to the UP position; the front of
the tilt table should move upwards. Move the joy-
stick to the DOWN position; the front of the tilt
table should move downwards.
d. When a pan limit is reached, scan direction is
Table A. Available Duty Cycle Combinations
Duty Cycle
2. Move the joystick to the LEFT position; the unit
should pan to the left. With the joystick at the
RIGHT position, the unit should pan to the right.
CR11
CR9
CR10
(Percent)
3. Test operation of the diagonal positions of the joy-
stick (which combine both pan and tilt functions
simultaneously). For example, moving the joystick
diagonally to the left between LEFT and UP should
pan the unit to the left and move the tilt table up.
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
50
25
17
12.5
10
8
5.2 AUTO/RANDOM SCAN
OPERATION TEST
7
6.25
The MPTA24DT, MPTA115DT, and MPTA220DT Se-
ries provide two modes of automatic pan operation –
Random Scan and continuous Auto Scan. After install-
ing the interconnecting cable between the pan/tilt and
control, plug control into the AC outlet, turn control
on, and test operation using the following procedures:
1 = Diode in circuit.
0 = Diode out of circuit
reversed automatically.
5.2.2 Continuous Auto Scan
5.2.1 Random Scan Operation
For continuous AUTO/SCAN, activate the rocker
switch in theAUTO/RANDOM position a second time.
After approximately one half hour in Auto Scan, the
unit automatically reverts to Random Scan.
1. For Random Scan operation, activate the rocker
switch located on the left side of the control in the
AUTO/RANDOM position. Activation of this
switch causes scanning between limits in an un-
predictable pattern:
NOTE: PressingAUTO/RANDOM while in
Random Scan causes a shift to Auto Scan and
starts the half hour timer. Similarly, pressing
AUTO/RANDOM while in Auto Scan causes
a shift to Random Scan and zeros the half hour
timer.
a. The scan duration varies randomly between
approximately 0 and 60 seconds.
b. At the completion of a scan period, a dwell
(or rest) period occurs. This dwell period var-
ies randomly between about 4 seconds and an
adjustable 60 to 900 seconds.
For MPTA24DT, MPTA115DT and MPTA220DT,
manual operation can be activated two ways — by
pressing MANUAL or by moving the joystick while
the unit is in Auto or Random Scan.
Pelco Manual C520M Rev B (6/92)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6.0 MAINTENANCE
ELECTRICAL
Under normal operating conditions and usage, mainte-
nance of this equipment is not necessary. However, if
maintenance is required, contact a Qualified Service
Technician or return to the factory for repair.
Input Voltage: 120 VAC or 230 VAC, 50/60 Hz
Auto/Random
Circuit:
Anoisegeneratordrivesascan/dwell
flip-flopwhichislogicallyandedwith
a direction flip-flop causing random
scan and random dwell periods as
well as random scan direction. Upon
limitswitchactivation,acurrentsens-
ing circuit detects the absence of the
motor drive circuit and reverses scan
direction.
7.0 SPECIFICATIONS
CONTROLS
Pan/Tilt:
8-position joystick (Up, down, left,
rightandsimultaneouscombinations
of pan/tilt functions when joystick is
positioned diagonally between two
functions)
Output Voltage:
24 VAC
MPT24DT, MPT24DT/220,
MPTA24DT, MPTA24DT/220
MPT115DT, MPTA115DT
MPT220DT, MPTA220DT
Auto/Random
Scan:
3 position rocker switch:
– AUTO/RANDOM
– ON (manual)
120 VAC
230 VAC
– OFF
Fuse Protection: 1 amp SB
Pilot Lamp:
Long life neon
Power Cord:
Connectors:
Conductor
3-wire grounded, #18 Awg
AmpCPCtype,14-pin(matesupplied)
Requirements: 5 plus ground (no additional conduc-
tors for auto/random scan)
Cable Distances: Refer to the specifications for the spe-
cificpan/tilttobeusedwiththecontrol.
6
Pelco Manual C520M Rev B (6/92)
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL
Construction:
Cover
Chassis
Panel
Steel, black polyester powder coat
Steel, zinc plated
Aluminum, black polyester powder
coat and white silkscreen
Dimensions:
Weight:
See Figure 3
MPT24DT/MPTA24DT
MPT115DT/MPTA115DT
MPT220DT/MPTA220DT
5 lbs (2.27 kg)
3 lbs (1.36 kg)
3 lbs (1.36 kg)
Shipping Weight:
MPT24DT/MPTA24DT
MPT115DT/MPTA115DT
MPT220DT/MPTA220DT
7 lbs (3.17 kg)
5 lbs (2.27 kg)
5 lbs (2.27 kg)
Rating:
NEMA 1
Figure 3. Dimension Drawing
Pelco Manual C520M Rev B (6/92)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8.0 WARRANTY AND RETURN
INFORMATION
WARRANTY
RETURNS
Pelco will repair or replace, without charge, any merchandise proved
defectiveinmaterialorworkmanshipforaperiodofoneyearafterthedate
of shipment.
In order to expedite parts returned to the factory for repair or credit, please
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an
authorization number (CA number if returned for credit, and RA number
if returned for repair).
Exceptions to this warranty are as noted below:
All merchandise returned for credit may be subject to a 20% restocking
and refurbishing charge.
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and
keyboard).
Goods returned for repair or credit should be clearly identified with the
assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.
•
Three years on Camclosure® and fixed camera models, except the
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.
If you are located within the continental U.S., Alaska, Hawaii or Puerto
Rico, send goods to:
•
•
Two years on standard motorized or fixed focal length lenses.
Service Department
Pelco
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and
DF5/DF8 Series fixed dome products.
3500 Pelco Way
Clovis, CA 93612-5699
•
•
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, includ-
ing when used in continuous motion applications.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto
Rico and are instructed to return goods to the USA, you may do one of the
following:
Two years on Esprit® and WW5700 Series window wiper (excluding
wiper blades).
Eighteen months on DX Series digital video recorders, NVR300
Series network video recorders, and Endura™ Series distributed
network-based video products.
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
•
•
One year (except video heads) on video cassette recorders (VCRs).
Video heads will be covered for a period of six months.
If the goods are to be sent by a FREIGHT FORWARDER, send the goods
to:
Six months on all pan and tilts, scanners or preset lenses used in
continuousmotionapplications(thatis,presetscan,tourandautoscan
modes).
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation from
state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800)
289-9100 or (559) 292-1981 to obtain a Repair Authorization number
(RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice
number
3. Details of the defect or problem If there is a dispute regarding the
warranty of a product which does not fall under the warranty conditions
stated above, please include a written explanation with the product
when returned.
Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
8
Pelco Manual C520M Rev B (6/92)
Download from Www.Somanuals.com. All Manuals Search And Download.
|