Pelco TV Mount C1301M User Manual
O P E R A T I O N / P R O G R A M M I N G  
™
ExSite Explosionproof  
EHXM Series  
Fixed Mount System  
®
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
How to Operate Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Accessing Main Menu (Preset 95). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
CM6700/CM6800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
KBD200A/KBD300A (Direct Mode Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
CM9500. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
CM9700 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
KBD4000/KBD4002. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
MPT9500. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
NET300/NET350/NET4001A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Quick Start Guide – System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Display Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Label Positions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Unit Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Type of Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Auto Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Zoom Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Zoom Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Low Light Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
IR Cut Filter (23X Day/Night Camera). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Advanced Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Shutter Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
AGC Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Auto Iris. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Auto Sharpness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Auto White Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Backlight Compensation (BLC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Video Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Wide Dynamic Range (23X Day/Night Camera). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Other . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Park Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Power Up Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Line Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Enable Motion Detection (23X Day/Night Camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Edit Detection Areas (23X Day/Night Camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Activate AUX Command (23X Day/Night Camera). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
AUX Time (23X Day/Night Camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Window Blanking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Clear Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
C1301M (6/05)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Wiper Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Wiper Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Wiper Dwell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Wiper Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Set Washer Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Aux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Clear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Reset, Cycle Power, Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
Reset Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
Cycle Camera Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
Reboot System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
Software/Language File Upload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Upload Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
4
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regulatory Notices  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause  
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired  
operation.  
RADIO AND TELEVISION INTERFERENCE  
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment  
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and the receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.”  
This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.  
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to  
operate this equipment under Federal Communications Commission’s rules.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
C1301M (6/05)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Welcome  
Thank you for purchasing Pelco’s ExSite™ EHXM Series explosionproof system. Your new system features a high resolution camera/optics  
package with programmable software.  
This manual is designed to be a reference tool for the operation and programming of your system. Inside you will find information about the  
features and commands of your EHXM system, as well as a detailed menu tree.  
MODELS  
EHXM30C22-2  
EHXM30C22-2X  
EHXM31C22-2  
EHXM31C22-2X  
Fixed IOP system with color camera, 60 Hz, 24 VAC  
Fixed IOP system with color camera, 50 Hz, 24 VAC  
Same as EHXM30C22-2, except supplied with window wiper  
Same as EHXM30C22-2X, except supplied with window wiper  
EHXM30CBW23-2 Fixed IOP system with day/night camera, 60 Hz, 24 VAC  
EHXM30CBW23-2X Fixed IOP system with day/night camera, 50 Hz, 24 VAC  
EHXM31CBW23-2 Same as EHXM30CBW23-2, except supplied with window wiper  
EHXM31CBW23-2X Same as EHXM30CBW23-2X, except supplied with window wiper  
EHXM30C22-7  
EHXM30C22-7X  
EHXM31C22-7  
EHXM31C22-7X  
Fixed IOP system with color camera, 60 Hz, 90-264 VAC  
Fixed IOP system with color camera, 50 Hz, 90-264 VAC  
Same as EHXM30C22-7, except supplied with window wiper  
Same as EHXM30C22-7X, except supplied with window wiper  
EHXM30CBW23-7 Fixed IOP system with day/night camera, 60 Hz, 90-264 VAC  
EHXM30CBW23-7X Fixed IOP system with day/night camera, 50 Hz, 90-264 VAC  
EHXM31CBW23-7 Same as EHXM30CBW23-7, except supplied with window wiper  
EHXM31CBW23-7X Same as EHXM30CBW23-7X, except supplied with window wiper  
GETTING STARTED  
DANGER: Do not connect the power module to a supply circuit unless all ExSite system components (enclosure, camera  
module and power module) are installed.  
You will need to install your system before using this manual. Refer to the installation manuals for installation instructions. Once installed  
apply power to the system. The system will start a configuration sequence. When configuration is done, the following information is  
displayed on the monitor:  
EXSITE EHXM  
Version X.XX  
D Address: 1  
P Address: 2  
Comm 2400, N, 8, 1  
CONFIGURE DONE  
This information will remain on the monitor until system operation begins. Refer to the following pages to learn how to operate and  
program your EHXM Series system.  
6
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
How to Operate Your System  
Operation  
How to Control  
Zoom Far  
To zoom far, do the following:  
1. Press the Zoom Tele button or turn the joystick clockwise until zoom stops at the 32X zoom limit.  
2. Release the button or joystick for one second.  
3. To continue zooming (digitally), press the button or turn the joystick clockwise again until you have the picture you  
want or reach the digital zoom* limit.  
Zoom Wide  
Alarms  
Press the Zoom Wide button or turn the joystick counterclockwise.  
Refer to the Alarms section.  
C1301M (6/05)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ACCESSING MAIN MENU (PRESET 95)  
You can call up the main menu on your monitor by programming (setting or creating) preset 95 (preset 28 if in AD32-preset mode).  
Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for programming preset  
95 are given below for various Pelco controllers.  
CM6700/CM6800  
1. Enter the number of the ExSite EHXM system and press the CAM key.  
2. Enter 95 and hold the PRESET key for two seconds.  
3. In the Edit Preset menu, arrow to SET and press the ACK key. The main menu appears.  
KBD200A/KBD300A (DIRECT MODE ONLY)  
1. Enter 95.  
2. Hold the PRESET key (approximately five seconds) until the main menu appears on the screen.  
CM9500  
1. Enter the number of the ExSite EHXM system and press the CAM key. The Main menu appears.  
2. Highlight SETUP in the Main menu and press the SELECT key.  
3. Highlight CAM in the Setup menu and press the SELECT key.  
4. Highlight PRESET in the Camera menu and press the SELECT key.  
5. Enter 95 and press the F1 key. The main menu appears.  
CM9700 SERIES  
1. Press the ESCAPE key to open the Main menu. Select DEF. The Define Submenu appears.  
2. Enter your four-digit PIN if this is your first time entering this mode.  
3. Enter 95 and select PRST. The main menu appears on the monitor.  
4. Select the Quit icon to return to the default menu.  
KBD4000/KBD4002  
1. Press the SPOT MONITOR key.  
2. Enter 95, then hold the PRESET key (approximately five seconds) until the main menu appears on the screen.  
MPT9500  
Standard Coaxitron Mode  
1. Enter 95 and press the PRESET SET key.  
2. Position the asterisk in the YES row and press the F1 key. The main menu appears.  
Extended Coaxitron or RS-485 Mode  
1. Enter 95 and press the PRESET SET key.  
2. Press the F2 key. The main menu appears.  
NET300/NET350/NET4001A  
1. Check the Set box.  
2. Click the preset 95 button. The main menu appears.  
8
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Quick Start Guide – System Setup  
PELCO EXSITE EHXM  
LANGUAGE  
Quick Programming Guide  
Access the main menu (preset 95). Refer to  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
Accessing Main Menu (Preset 95) section.  
<UNIT SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
Use the joystick to position the cursor beside  
menu selection. If your controller does not have a  
joystick, use the up or down key.  
Presets  
The following presets are reserved for special functions.  
EXIT  
Preset  
86  
Function  
Press Iris Open; the submenu/cursor moves to the right.  
Wiper  
87  
88  
89  
95  
Washer  
IR filter IN (color)  
IR filter OUT (black-white)  
Select main programming menu  
Move the joystick up or down to view selections. If  
your controller does not have a joystick, use the up  
or down key.  
NOTE: For American Dynamics controllers with only 32 presets, switch SW3-1  
DISPLAY SETUP  
PRESET LABEL  
ZOOM  
ADDITIONAL  
FREE MEMORY  
SYSTEM INFORMATION  
LABEL POSITION  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
on the dome drive to the ON position. When SW3-1 is ON, preset  
UNIT MODEL  
[PRESET LABEL- - - ---]  
[ALARM 1- - - - - - -]  
Press Iris Open to make selection.  
95 becomes 28  
89 becomes 22  
88 becomes 21  
LAST RESET  
CAMERA ACTIVE  
FPGA VERSION  
VIDEO LEVEL  
<CAMERA>  
<EAB>  
POWER MODULE MEMORY  
SOFTWARE VERSION  
BIOS VERSION  
ALARM MESSAGE  
SAVE AND EXIT  
CANCEL AND EXIT  
HELP  
FONT VERSION  
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
Press Iris Close to cancel selection.  
<PMAB>  
COMM  
D ADDRESS  
P ADDRESS  
CM9500 MODE  
32 PRESETS  
PROTOCOL  
BACK  
EXIT  
XXX.XXX  
LANGUAGE 1  
LANGUAGE 2  
LANGUAGE 3  
LANGUAGE 4  
LANGUAGE 5  
LANGUAGE 6  
LANGUAGE 7  
LANGUAGE 8  
LANGUAGE 9  
LANGUAGE 10  
<AUX>  
<CLEAR>  
<PASSWORD>  
<ADDITIONAL>  
BACK  
EXIT  
BACK  
EXIT  
BACK  
EXIT  
POWER UP  
CAMERA  
OTHER  
LYNE SYNC  
PRESETS  
PATTERNS  
WINDOW BLANKING  
STYLE  
ALARMS  
WIPER**  
AUX  
AUX 1 MODE  
DWELL TIME (SECS)  
CLEAR  
PASSWORD  
TYPE OF LIGHTING  
AUTO FOCUS  
ZOOM LIMIT  
PARK TIME (MINUTES)  
PARK ACTION  
POWER UP ACTION  
LINE SYNC  
LINE SYNC PHASE  
PRESET NUMBER  
PATTERN NUMBER  
<PROGRAM PATTERN>  
<CLEAR PATTERN>  
RESUME  
WIPER CONTROL  
WIPER MODE  
WIPER DWELL (SECS)  
WIPER TIME (MIN)  
CLEAR ALL PRESETS  
CLEAR ALL PATTERNS  
CLEAR ALL WINDOW BLANKING  
ENABLE PASSWORD  
<EDIT PASSWORD>  
SEQUENCE (SECS)  
RESET DELAY (SECS)  
BACK  
EXIT  
PRESET NOT DEFINED  
<SET WINDOWS>  
ZOOM SPEED  
BACK  
EXIT  
BACK  
EXIT  
AUX 2 MODE  
DWELL TIME (SECS)  
BACK  
EXIT  
LOW LIGHT LIMIT  
IR CUT FILTER*  
AUTO IR LEVEL*  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<MOTION DETECTION>*  
BACK  
EXIT  
BACK  
EXIT  
<ALARM SETTINGS>  
RESTORE FACTORY DEFAULTS  
<SET WASHER SEQUENCE>  
BACK  
EXIT  
BACK  
EXIT  
BACK  
EXIT  
REFERENCE INFORMATION  
PATTERN USAGE  
BACK  
EXIT  
<ADVANCED SETTINGS>  
<CLEAR PRESETS>  
<CLEAR CAMERA SETTINGS>  
REMAINING  
BACK  
EXIT  
BACK  
EXIT  
ADVANCED SETTINGS  
MOTION DETECTION*  
SET WINDOWS  
ALARM SETTINGS  
ALARM NUMBER  
SET WASHER SEQUENCE  
PRESET NOT DEFINED  
SHUTTER SPEED  
AGC LIMIT  
MOTION DETECTION ENABLED  
<EDIT DETECTION AREA>  
WINDOW NUMBER  
EDIT THE PASSWORD  
- - - - - - - - - - - - - - - - -  
1234567890 OK  
AUTO IRIS  
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
ACTIVATE AUX  
AUX TIME  
ABCDEFGHIJ  
KLMNOPQRST  
UZWXYZ.,-/  
abcdefghij  
CANCEL  
ENABLE WINDOW  
REVERSE  
CLEAR WINDOW  
ALARM CONTACT  
SPACE  
BACKSPACE  
BACK  
EXIT  
WASHER TIME (SECS)  
WIPER DELAY (SECS)  
AUTO RETURN  
BACK  
EXIT  
klmnopqrst  
uvwxyz*;:  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
BACK  
EXIT  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
WIDE DYNAMIC RANGE*  
BACK  
EXIT  
BACK  
EXIT  
EDIT DETECTION AREA*  
DETECTION AREA 1  
LOCATION  
SENSITIVITY  
DETECTION AREA 2  
LOCATION  
SENSITIVITY  
DETECTION AREA 3  
LOCATION  
SENSITIVITY  
DETECTION AREA 4  
LOCATION  
SENSITIVITY  
BACK  
EXIT  
*Available only with the 23X day/night camera.  
**Available only with wiper models.  
C1301M (6/05)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
10  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Language  
The language for the on-screen menus is selectable. Available languages include English, Spanish,  
French, German, Italian, Portuguese, Polish, Russian, Turkish, and Czecholslovakian. The factory  
default language is English.  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
To change the display language:  
1. Use the joystick to position the cursor beside LANGUAGE.  
2. Press Iris Open. The cursor moves to the right, beside the current, selected language.  
RESET CAMERA  
CYCLE CAMERA POWER  
3. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
All on-screen menus are changed to the selected language.  
EXIT  
Quick Programming Guide  
(See Page 9)  
C1301M (6/05)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
System Information  
The System Information screen displays ExSite model, software version, available memory, and  
other diagnostic information.  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
System settings cannot be changed using this screen. This screen is for reference only.  
Use the following steps to display the System Information screen:  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
1. Use the joystick to position the cursor beside SYSTEM INFORMATION.  
2. Press Iris Open. The SYSTEM INFORMATION window opens.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
SYSTEM INFORMATION  
UNIT MODEL  
EHXM30C22  
AVAILABLE  
0.90.9013  
8.00.9000  
1.00  
POWER MODULE MEMORY  
SOFTWARE VERSION  
BIOS VERSION  
FONT VERSION  
COMM  
2400,N,8,1  
D ADDRESS  
P ADDRESS  
CM9500 MODE  
32 PRESETS  
PROTOCOL  
1
2
OFF  
OFF  
D
<ADDITIONAL>  
BACK  
EXIT  
ADDITIONAL  
FREE MEMORY  
LAST RESET  
CAMERA ACTIVE  
FPGA VERSION  
VIDEO LEVEL  
CAMERA  
30464  
3
YES  
2
HIGH  
XXXX-XXXX  
<EAB>*  
<PMAB>**  
LANGUAGE 1  
LANGUAGE 2  
LANGUAGE 3  
LANGUAGE 4  
LANGUAGE 5  
LANGUAGE 6  
LANGUAGE 7  
LANGUAGE 8  
LANGUAGE 9  
LANGUAGE 10  
ENGLISH 1.00  
ESPANOL 1.00  
ITALIANO 1.00  
DEUTSCH 1.00  
PORTUGUES 1.00  
FRANCAIS 1.00  
CESKY 1.00  
POLSKI 1.00  
RUSSIAN 1.00  
TURKISH 1.00  
BACK  
EXIT  
**EAB (Enclosure Accessory Board) – The EAB information screen displays availability, version, and part  
number of the enclosure accessory board  
**PMAB (Power Module Accessory Board) – The EAB information screen displays availability, version,  
and part number of the power module accessory board.  
12  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Display Setup  
Display setup allows you to program how labels are displayed on the monitor. The following labels  
are available:  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
PRESET LABEL  
ZOOM  
ALARM MESSAGE Displays activated alarm.  
Identifies preset.  
Identifies the amount of magnification.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
A preset label is displayed when a preset is called. The zoom ratio label is displayed when zoom is  
activated. An alarm message appears on the monitor when an alarm occurs.  
The following settings are available for each label:  
EXIT  
OFF  
Label is not displayed when activated.  
CONSTANT  
2 SECONDS  
5 SECONDS  
10 SECONDS  
The label is continually displayed when activated.  
The label is displayed for 2 seconds after activation.  
The label is displayed for 5 seconds after activation.  
The label is displayed for 10 seconds after activation.  
DISPLAY SETUP  
PRESET LABEL  
ZOOM  
2 (SECS)  
2 (SECS)  
2 (SECS)  
ALARM MESSAGE  
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
BACK  
EXIT  
Quick Programming Guide  
(See Page 9)  
C1301M (6/05)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
LABEL POSITIONS  
Labels can be placed anywhere on the monitor. This feature allows you to customize the appearance  
of your monitor screen.  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
The following labels are not set at fixed positions:  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
Preset Label  
Alarm 1  
Zoom  
<UNIT SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
To set a label position:  
EXIT  
1. Use the joystick to position the cursor beside a label.  
2. Press Iris Open.  
3. Use the joystick to move the label up, down, left, and/or right.  
4. Press Iris Open.  
5. Repeat steps 1 through 4 to position other labels.  
6. Position the cursor next to Save and Exit. Press Iris Open to save settings and exit menu.  
DISPLAY SETUP  
PRESET LABEL  
ZOOM  
2 (SECS)  
2 (SECS)  
2 (SECS)  
ALARM MESSAGE  
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
BACK  
EXIT  
[PRESET LABEL ------------]  
[ALARM 1 ------------]  
SAVE AND EXIT  
CANCEL AND EXIT  
HELP  
XXX.X  
14  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Unit Settings  
CAMERA  
TYPE OF LIGHTING  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
Pelco has calibrated settings that optimize the white balance, and the picture, for indoor and  
outdoor lighting conditions. There are two settings:  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
OUTDOOR (default)  
INDOOR  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
AUTO FOCUS  
EXIT  
Auto focus allows the lens to remain in focus during zoom-in and zoom-out functions.  
There are two auto focus settings:  
UNIT SETTINGS  
ON (default)  
If auto focus mode is set to ON, the camera will focus  
automatically when using zoom functions.  
<CAMERA>  
<OTHER>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
OFF  
Focus is operated manually. To focus, press the Focus Far or Focus  
Near button on the controller.  
ZOOM LIMIT  
<AUX>  
<CLEAR>  
<PASSWORD>  
Zoom limit allows the user to define a limitation on the amount of telephoto zoom. The following are  
the zoom limit settings for the ExSite Series systems:  
BACK  
EXIT  
23X Day/Night Camera  
Camera zooms optically to 23X and then zooms electronically. 23X,  
32X, 92X,184X, or 230X. Default setting is 184X.  
22X Color Camera  
Camera zooms optically to 22X and then zooms electronically. 32X,  
88X, 176X, 220X, or 264X. The default setting is 176X.  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
OUTDOOR  
ON  
ZOOM SPEED  
ZOOM LIMIT  
X184  
ZOOM SPEED  
MEDIUM  
2
AUTO  
DUSK  
Zoom speed allows the user to define how fast the dome will go from full wide zoom to the  
optical zoom. The default setting is MEDIUM.  
LOW LIGHT LIMIT  
IR CUT FILTER*  
AUTO IR LEVEL*  
SPEED  
HIGH  
MEDIUM (default)  
LOW  
22X COLOR  
2.4 seconds  
3.9 seconds  
6.3 seconds  
23X DAY/NIGHT  
2.9 seconds  
4.2 seconds  
5.8 seconds  
<ADVANCED SETTINGS>  
BACK  
*Available only with the 23X day/night camera.  
NOTE: When using the HIGH setting, the image may be out of focus until zooming stops.  
LOW LIGHT LIMIT  
Low light limit is the maximum duration, in fractions of a second, that the electronic shutter will  
remain open in low light conditions. The default setting is 2.  
Settings include the following:  
2 = 1/2 second  
4 = 1/4 second  
8 = 1/8 second  
15 = 1/15 second  
30 = 1/30 second  
60 = 1/60 second  
Quick Programming Guide  
(See Page 9)  
C1301M (6/05)  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
IR CUT FILTER (23X DAY/NIGHT CAMERA)  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
ExSite EHXM has two modes of operation: color, and black-white. You can increase sensitivity in  
low light conditions by switching to black-white mode (removing the IR cut filter). Color mode is  
preferred in normal lighting conditions.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
The following are the settings for the IR cut filter:  
OFF  
Manual operation is controlled by preset 88 (filter IN) and 89 (filter OUT).  
AUTO (default) Automatic operation is controlled by the Auto IR Level setting.  
EXIT  
Auto IR Level  
The auto IR level is the light level at which the infrared filter switches IN or OUT.  
UNIT SETTINGS  
Following are the available settings for the Auto IR Level:  
<CAMERA>  
<OTHER>  
DUSK (default) Approximately 6 lux (black-white)  
Approximately 13 lux (color)  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
DARK  
Approximately 0.1 lux (black-white)  
Approximately 2 lux (color)  
NOTES:  
• If backlight compensation is ON and the IR cut filter switches OUT in normal lighting  
conditions, adjust the Auto IR Level to a darker setting. Refer to the Backlight Compensation  
(BLC) section.  
BACK  
EXIT  
• Low light does not mean no light. Some type of illumination is required (street light,  
IR light, etc.). The camera is not sensitive to IR light when the IR cut filter is IN.  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
OUTDOOR  
ON  
ZOOM LIMIT  
X184  
ZOOM SPEED  
MEDIUM  
2
AUTO  
DUSK  
LOW LIGHT LIMIT  
IR CUT FILTER*  
AUTO IR LEVEL*  
<ADVANCED SETTINGS>  
BACK  
*Available only with the 23X day/night camera.  
16  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
ADVANCED CAMERA SETTINGS  
SHUTTER SPEED  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
Shutter speed is the duration of the electronic shutter. Program shutter speed to operate  
automatically (Auto) or manually (Numeric Value).  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
AUTO (default)  
The electronic shutter speed is set automatically by the amount of light  
sensed by the camera.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
NUMERIC VALUE  
The system has several numerical shutter speed settings. The higher  
the number, the faster the electronic shutter.  
EXIT  
The slowest shutter speed setting is 2 = 1/2 second  
The fastest setting is 30,000 = 1/30,000 second  
Increasing the shutter speed lowers the light sensitivity and reduces the  
streaking of fast moving objects.  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
NOTE: Set the shutter speed to 100 if you are using an NTSC camera in a 50 Hz environment.  
This will eliminate any flicker that may occur in the picture.  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
AGC LIMIT  
<AUX>  
<CLEAR>  
<PASSWORD>  
AGC Limit allows users to adjust how the system balances AGC (automatic gain control) and  
electronic shutter in low-light conditions. As scene lighting decreases, the system will automatically  
adjust, adding a mixture of AGC and slow shutter according to the AGC LIMIT setting. AGC LIMIT  
can be set between 0 and 40, with 40 applying maximum AGC before slow shutter. In contrast,  
setting AGC LIMIT to 0 will force the system software to apply maximum slow shutter (as defined by  
the LOW LIGHT LIMIT setting) before any AGC is applied. The default setting of 28 sets the AGC and  
slow shutter balance to favor AGC, yielding more real-time low-light images.  
BACK  
EXIT  
NOTE: The maximum slow shutter that the system will achieve is 1/2 second shutter (refer to the  
CAMERA  
Low Light Limit section).  
TYPE OF LIGHTING  
AUTO FOCUS  
OUTDOOR  
ON  
ZOOM LIMIT  
X184  
ZOOM SPEED  
MEDIUM  
2
AUTO  
DUSK  
LOW LIGHT LIMIT  
IR CUT FILTER*  
AUTO IR LEVEL*  
<ADVANCED SETTINGS>  
BACK  
ADVANCED SETTINGS  
SHUTTER SPEED  
AGC LIMIT  
AUTO  
28  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO  
91  
16  
AUTO SHARPNESS  
SHARPNESS LEVEL  
ON  
26  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
ON  
146  
294  
BACKLIGHT COMP  
VIDEO LEVEL  
WIDE DYNAMIC RANGE*  
OFF  
HIGH  
OFF  
Quick Programming Guide  
BACK  
EXIT  
*Available only with the 23X day/night camera.  
(See Page 9)  
C1301M (6/05)  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
AUTO IRIS  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
Auto iris is the lens function that automatically opens and closes the iris in response to changing  
light conditions.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
Program the auto iris to operate automatically or at a user-defined level.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
OFF  
Auto iris is disabled, and control is always manual.  
AUTO (default) The iris is adjusted automatically to produce a constant video output as  
determined by the Auto Iris Level setting.  
EXIT  
NOTE: If auto iris is in the auto mode, it will remain that way until the iris is manually opened or  
closed. The system will return to auto mode when it is panned or tilted more than 15 degrees.  
UNIT SETTINGS  
Auto Iris Level  
<CAMERA>  
<OTHER>  
Auto iris level is the numeric value the auto iris uses to maintain the brightness level of the camera.  
Increase the value to brighten the scene. Decrease the level to darken the scene. This setting can be  
adjusted if the video level in the auto iris mode is too bright or too dark.  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
NOTE: If backlight compensation is ON, decrease the Auto Iris Level setting.  
Auto Iris Peak  
Increasing the peak value will cause the auto iris circuit to react more to highlights or “peaks” in the  
picture. Decreasing this value will cause it to use the average video level to adjust the iris.  
BACK  
EXIT  
AUTO SHARPNESS  
Auto sharpness enhances picture detail by increasing the aperture gain of the camera and  
sharpening the edges in the picture.  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
OUTDOOR  
ON  
There are two settings:  
ZOOM LIMIT  
X184  
ZOOM SPEED  
MEDIUM  
2
AUTO  
DUSK  
ON (default)  
OFF  
The camera automatically maintains a normal sharpness mode.  
LOW LIGHT LIMIT  
IR CUT FILTER*  
AUTO IR LEVEL*  
The sharpness of the picture is set manually by programming the sharpness  
level. Sharpness level settings range from 0-63.  
<ADVANCED SETTINGS>  
BACK  
AUTO WHITE BALANCE  
This feature automatically processes the viewed image to retain color balance over a color  
temperature range. The default setting for auto white balance is ON.  
ADVANCED SETTINGS  
R GAIN  
Adjusts the picture output in the red range. As you change the value, you will  
see the color change on your monitor.  
SHUTTER SPEED  
AGC LIMIT  
AUTO  
28  
B GAIN  
Adjusts the picture output in the blue range. As you change the value, you will  
see the color change on your monitor.  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO  
91  
16  
AUTO SHARPNESS  
SHARPNESS LEVEL  
ON  
26  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
ON  
146  
294  
BACKLIGHT COMP  
VIDEO LEVEL  
WIDE DYNAMIC RANGE*  
OFF  
HIGH  
OFF  
BACK  
EXIT  
*Available only with the 23X day/night camera.  
18  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
BACKLIGHT COMPENSATION (BLC)  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette.  
Backlight compensation enhances objects in the center of the picture. The system uses the center of  
the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to  
white. The camera will adjust the iris so that the object in the sensitive area is properly exposed.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
There are two backlight compensation settings:  
ON  
Backlight compensation is activated.  
EXIT  
OFF (default) Backlight compensation is not activated.  
NOTE: If backlight compensation is ON, decrease the Auto Iris setting and adjust the Auto IR Level  
to a darker setting. Refer to the Auto Iris and Auto IR Level sections.  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
VIDEO LEVEL  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
Set the video output to one of the following:  
NORMAL - 1.0 volt peak-to-peak  
HIGH (default setting) - 1.2 volt peak-to-peak to compensate for losses in video cable.  
WIDE DYNAMIC RANGE (23X DAY/NIGHT CAMERA)  
BACK  
EXIT  
The wide dynamic range (WDR) setting balances the brightest and darkest sections of a scene to  
produce a picture that is better balanced in lighting and provides more detail. The range from the  
darkest to the brightest sections of the scene is 80X more when WDR is ON than when OFF.  
Available settings are OFF and ON. The default setting is OFF. When wide dynamic range is set to  
ON the frame rate is reduced from the standard 30 frames per second to 15 frames per second.  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
OUTDOOR  
ON  
ZOOM LIMIT  
X184  
ZOOM SPEED  
MEDIUM  
2
AUTO  
DUSK  
LOW LIGHT LIMIT  
IR CUT FILTER*  
AUTO IR LEVEL*  
<ADVANCED SETTINGS>  
BACK  
ADVANCED SETTINGS  
Wide Dynamic Range ON  
Wide Dynamic Range OFF  
SHUTTER SPEED  
AGC LIMIT  
AUTO  
28  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO  
91  
16  
AUTO SHARPNESS  
SHARPNESS LEVEL  
ON  
26  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
ON  
146  
294  
BACKLIGHT COMP  
VIDEO LEVEL  
WIDE DYNAMIC RANGE*  
OFF  
HIGH  
OFF  
BACK  
EXIT  
Quick Programming Guide  
*Available only with the 23X day/night camera.  
(See Page 9)  
C1301M (6/05)  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
OTHER  
PARK TIME  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
This feature allows the system to begin a specified operation (preset or pattern) after a programmed  
time of inactivity.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
Park time can be programmed from 1 minute to 720 minutes (12 hours), or set to zero, which  
disables this feature. The default setting is zero.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
Park Action  
EXIT  
This feature will define the activity when the system parks. The following settings are available:  
NONE (default) No action.  
PRESET 1  
The system goes to preset 1.  
The system goes to preset 8.  
The system runs pattern 1.  
The system runs pattern 2.  
The system runs pattern 3.  
The system runs pattern 4.  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
PRESET 8  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
PATTERN 1  
PATTERN 2  
PATTERN 3  
PATTERN 4  
<AUX>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
OTHER  
PARK TIME (MINUTES)  
PARK ACTION  
0
NONE  
BACK  
EXIT  
20  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
POWER UP  
POWER UP ACTION  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
This setting defines a specific activity to be performed in the event the power to the system  
is cycled.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
The following settings are available:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
NONE  
No action.  
AUTO (default) The camera maintains its previous camera settings before the power outage.  
EXIT  
PRESET 1  
The system to preset 1.  
The system to preset 8.  
The system pattern 1.  
The system pattern 2.  
The system pattern 3.  
The system pattern 4.  
PRESET 8  
PATTERN 1  
PATTERN 2  
PATTERN 3  
PATTERN 4  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
POWER UP  
POWER UP ACTION  
AUTO  
BACK  
EXIT  
Quick Programming Guide  
(See Page 9)  
C1301M (6/05)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
LINE SYNC  
Line sync refers to a programmable function that allows you to synchronize all cameras within a  
PELCO EXSITE EHXM  
matrix system.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
NOTE: ExSite EHXM automatically senses V-sync input. No line sync setup is required for Pelco  
control systems that provide a V-sync signal.  
For matrix systems that do not output V-sync, there are two settings for line synchronization:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ON (default)  
Adjusts the phase of the line sync to synchronize input power. LINE SYNC  
PHASE settings range from 0-359 degrees.  
EXIT  
OFF  
The system synchronizes to an internal clock.  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
LINE SYNC  
LINE SYNC  
LINE SYNC PHASE  
ON  
0
BACK  
22  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PRESETS  
The ExSite EHXM system has 80 programmable preset positions. Each preset can be programmed to  
PELCO EXSITE EHXM  
use all programmable camera settings, and motion detection.  
The presets are numbered 1-32 and 35-82.  
Use the following steps to program a preset.  
1. Select the preset number:  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
a. Use the joystick to position the cursor beside PRESET NUMBER. Press Iris Open.  
The cursor moves to the right.  
EXIT  
b. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
2. Edit the preset label:  
a. Use the joystick to position the cursor beside EDIT PRESET LABEL.  
b. Press Iris Open. The following appears on the monitor:  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
LABEL FOR PRESET  
PRESET NUMBER ------  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
OK  
CANCEL  
SPACE  
BACKSPACE  
klmnopqrst  
uvwxyz*;:  
c. Use the joystick to position the cursor beside a character. Press Iris Open to enter the  
BACK  
EXIT  
selection. To clear a character, position the cursor beside BACKSPACE, and then press  
Iris Open.  
d. When the label is completed, move the cursor to OK. Press Iris Open to return to the  
Preset menu.  
PRESETS  
3. Edit the preset scene:  
PRESET NUMBER  
***PRESET NOT DEFINED***  
1
a. Use the joystick to position the cursor beside EDIT PRESET SCENE.  
b. Press Iris Open.  
c. Follow the directions displayed on the monitor.  
<EDIT PREST LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<MOTION DETECTION>*  
4. Edit preset camera settings:  
a. Use the joystick to position the cursor beside EDIT CAMERA SETTINGS.  
b. Press Iris Open. The EDIT CAMERA SETTINGS window appears on the monitor. Refer to  
the Camera and Advanced Camera Settings sections of this manual to change preset  
camera settings.  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
BACK  
EXIT  
REFERENCE INFORMATION  
ZOOM  
CUSTOM CAMERA SETTINGS  
NOTES:  
--  
--  
• There are two additional options available for the IR Cut Filter that are only available when  
programming a preset. The additional settings are YES and NO. If the IR Cut Filter is set to  
YES, the preset scene will be in color. If the IR Cut Filter is set to NO, the preset scene will  
be in black and white.  
*Available only with the 23X day/night camera.  
• You can copy camera settings from one preset to another preset. To copy camera settings  
do the following:  
1. Use the joystick to position the cursor beside COPY CAMERA SETTINGS.  
2. Press Iris Open. The cursor moves to the right.  
3. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
Quick Programming Guide  
(See Page 9)  
C1301M (6/05)  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ENABLE MOTION DETECTION (23X DAY/NIGHT CAMERA)  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
The following are the settings for MOTION DETECTION ENABLED:  
OFF (default) Motion detection is turned off (disabled).  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
ON  
Motion detection is turned on (enabled).  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
NOTE: Motion detection does not work if the shutter speed is set at less than 1/60 of a second.  
EDIT DETECTION AREAS (23X DAY/NIGHT CAMERA)  
EXIT  
Four motion detection areas can be defined for a preset. Use the following steps to edit motion  
detection areas.  
UNIT SETTINGS  
1. Edit detection areas 1, 2, 3, or 4:  
<CAMERA>  
<OTHER>  
a. Use the joystick to position the cursor beside EDIT DETECTION AREAS.  
b. Press Iris Open. The EDIT DETECTION AREAS programming window appears on the monitor.  
c. Use the joystick to position the cursor beside LOCATION for DETECTION AREA 1, 2, 3 or 4.  
d. Press Iris Open. The cursor moves to the right next to the number 0.  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
e. Move the joystick up. A blue rectangle appears in the upper left-hand corner of the screen.  
f.  
Use the joystick to place the blue rectangle over the desired detection area.  
g. Press Iris Open to make a selection.  
NOTE: Motion detection is not guaranteed to catch 100% of activity.  
BACK  
EXIT  
MOTION DETECTION AREAS  
PRESETS  
PRESET NUMBER  
***PRESET NOT DEFINED***  
1
<EDIT PREST LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<MOTION DETECTION>*  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
BACK  
EXIT  
REFERENCE INFORMATION  
ZOOM  
CUSTOM CAMERA SETTINGS  
--  
--  
MOTION DETECTION*  
MOTION DETECTION ENABLED  
<EDIT DETECTION AREAS>  
OFF  
2. Set the sensitivity of the motion detection area:  
EDIT DETECTION AREAS*  
DETECTION AREA 1  
a. Position the cursor next to SENSITIVITY for DETECTION  
AREA 1, 2, 3 or 4.  
b. Press Iris Open, the cursor moves to the right.  
c. Use the joystick to select one of the following sensitivity  
levels:  
LOCATION  
SENSITIVITY  
0
ACTIVATE AUX  
AUX TIME (SECS)  
OFF  
0
MEDIUM  
DETECTION AREA 2  
LOCATION  
SENSITIVITY  
0
BACK  
EXIT  
MEDIUM  
DETECTION AREA 3  
LOCATION  
SENSITIVITY  
0
MEDIUM  
HIGH - The sensitivity level is high. Slight changes  
in light level and contrast are detectable.  
MEDIUM (default) - Average sensitivity.  
LOW - The sensitivity level is low.  
DETECTION AREA 4  
LOCATION  
0
SENSITIVITY  
BACK  
EXIT  
MEDIUM  
*Available only with the 23X day/night camera.  
d. Press Iris Open to make selection.  
*AVAILABLE ONLY WITH THE 23X  
DAY/NIGHT CAMERA.  
24  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
ACTIVATE AUX COMMAND (23X DAY/NIGHT CAMERA)  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
Motion detection can be programmed to trigger an auxiliary command when motion is detected.  
The following are the settings for ACTIVATE AUX:  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
OFF (default) Motion detection will not trigger an AUX command.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
1
2
Triggers a command to AUX 1.  
Triggers a command to AUX 2.  
EXIT  
AUX TIME (23X DAY/NIGHT CAMERA)  
Aux time is the length of time the auxiliary will remain on after motion is detected. Available  
settings for AUX TIME are 1 through 60 seconds.  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
PRESETS  
PRESET NUMBER  
***PRESET NOT DEFINED***  
1
<EDIT PREST LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<MOTION DETECTION>*  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
BACK  
EXIT  
REFERENCE INFORMATION  
ZOOM  
CUSTOM CAMERA SETTINGS  
--  
--  
MOTION DETECTION*  
MOTION DETECTION ENABLED  
<EDIT DETECTION AREAS>  
OFF  
ACTIVATE AUX  
AUX TIME (SECS)  
OFF  
0
BACK  
EXIT  
*Available only with the 23X day/night camera.  
Quick Programming Guide  
(See Page 9)  
C1301M (6/05)  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
PATTERNS  
A pattern is a memorized, repeating, series of zoom and preset functions that can be recalled with a  
command from a controller or automatically by a programmed function (alarm or power-up).  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
The ExSite EHXM can handle up to four user-defined patterns. Pattern length is based upon memory  
usage rather than a fixed amount of time. The complexity of a pattern will determine the amount of  
storage available to program other patterns.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
To program a pattern:  
1. Use the joystick to position the cursor beside PATTERN NUMBER. Press Iris Open. The cursor  
moves to the right.  
EXIT  
2. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
3. Use the joystick to position the cursor beside PROGRAM PATTERN.  
4. Press Iris Open. The Patterns programming window appears on the monitor.  
5. Follow the directions displayed on the monitor.  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
After a pattern is programmed, the remaining storage percentage is displayed on the screen. This is  
the amount of memory available to program the remaining patterns.  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
To clear a pattern:  
1. Use the joystick to position the cursor beside CLEAR PATTERN.  
2. Press Iris Open.  
3. Follow the directions displayed on the monitor.  
<AUX>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
NOTES:  
• When programming one or more presets within a pattern use the normal controller  
commands to Call a Preset.  
• Not all controllers can start all four patterns. However, any of the four patterns can be  
automatically started with power-up, and alarm functions.  
PATTERNS  
PATTERN NUMBER  
1
<PROGRAM PATTERN>  
<CLEAR PATTERN>  
BACK  
EXIT  
REFERENCE INFORMATION  
PATTERN USAGE  
REMAINING  
0%  
100%  
26  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
WINDOW BLANKING  
Window blanking allows a user to program up to eight, four-sided, user-defined areas that cannot be  
viewed by the operator of the system. A blanked area will automatically adjust in size as the lens  
zooms telephoto and wide.  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
ExSite EHXM has two style modes for window blanking, GRAY and SMEAR. If style is set to gray,  
the blanked area is covered with a solid gray window. If smear is selected, images behind the  
window will be noticeable but not distinguishable.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
To set a window blanking area:  
1. Use the joystick to position the cursor beside WINDOW BLANKING. Press Iris Open. The  
WINDOW BLANKING menu appears on the screen.  
EXIT  
2. Move the joystick to position the cursor beside SET WINDOWS. Press Iris Open to enter.  
3. Position the cursor beside WINDOW NUMBER. Press Iris Open. The cursor moves to the right.  
4. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
5. Use the joystick to position the cursor beside EDIT WINDOW LOCATION. Press Iris Open, and  
then follow the instructions that appear on the screen.  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
NOTE: Use the inside corner of the window selection tool as a  
guide when selecting the upper left, upper right, bottom right,  
and bottom left corners of the window.  
<AUX>  
INSIDE CORNER  
<CLEAR>  
<PASSWORD>  
Set windows are not visible when editing a new window location.  
BACK  
EXIT  
When all four corners are set, the SET WINDOWS menu reappears, the blanked area is  
displayed, and the ENABLE WINDOW option is set to YES.  
6. The blanked area can be programmed to turn on or off at a specified zoom point. To set the  
zoom point:  
WINDOW BLANKING  
a. Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then press  
STYLE  
GRAY  
Iris Open.  
b. Zoom in to the point where you want window blanking to turn on. Press Iris Open to set  
the zoom point.  
<SET WINDOWS>  
BACK  
EXIT  
NOTES:  
• Since the area is already blanked out, it may be difficult to determine when you want  
window blanking to turn on. Reverse the window before setting the zoom point.  
When finished reverse the window again to blank out the area.  
SET WINDOWS  
• Increase the size of the window if any part of the blanked area is revealed during pan, tilt,  
and zoom operations.  
WINDOW NUMBER  
1
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
ENABLE WINDOW  
REVERSE  
CLEAR WINDOW  
NO  
BACK  
EXIT  
Window Blanking Disabled  
Window Blanking Enabled  
Quick Programming Guide  
(See Page 9)  
C1301M (6/05)  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
REVERSE  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
A blanked out area can be reversed to make it visible and the areas on both sides of it not visible.  
The areas above and below the blanking area remain visible. Reversing the window a second time  
will return it to its original condition.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
CLEAR WINDOW  
All areas that have been set for window blanking are cleared.  
EXIT  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
WINDOW BLANKING  
STYLE  
GRAY  
<SET WINDOWS>  
BACK  
EXIT  
SET WINDOWS  
WINDOW NUMBER  
1
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
ENABLE WINDOW  
REVERSE  
CLEAR WINDOW  
NO  
BACK  
EXIT  
28  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
ALARMS  
The ExSite EHXM system has seven alarm inputs, which can be programmed as high, medium or low  
priority. When an alarm is received, an input signal to the unit triggers the user-defined action (go to  
preset, run pattern, etc.) programmed for the alarm.  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
There are three global alarm settings:  
<UNIT SETTINGS>  
RESUME  
This mode lets the system resume its previous camera settings after all  
alarms are cleared.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
SEQUENCE  
This is the time the system will perform an alarm activity when more than one  
alarm of the same priority occurs at the same time.  
EXIT  
RESET DELAY This is the amount of time the system considers the alarm to be active after it  
has physically cleared.  
Use the following steps to program alarm settings.  
UNIT SETTINGS  
1. Use the joystick to position the cursor beside ALARM SETTINGS. Press Iris Open.  
<CAMERA>  
<OTHER>  
2. Select the alarm number:  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
a. Use the joystick to position the cursor beside ALARM NUMBER.  
b. Press Iris Open. The cursor moves to the right.  
c. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
3. Select the alarm priority:  
a. Use the joystick to position the cursor beside ALARM PRIORITY.  
b. Press Iris Open. The cursor moves to the right.  
c. Move the joystick up or down to view the available selections. Available settings include  
HIGH, MEDIUM, and LOW (default). If multiple alarms with different priorities are active  
at the same time, the dome will only go to the alarms with the highest priority.  
d. Press Iris Open to enter selection.  
BACK  
EXIT  
NOTES:  
ALARMS  
• HIGH alarm action takes highest priority and will override manual pan, tilt, and zoom  
control.  
RESUME  
SEQUENCE (SECS)  
RESET DELAY (SECS)  
OFF  
5
• MEDIUM/LOW alarm action will not occur if an alarm occurs during manual pan, tilt, and  
zoom control.  
<ALARM SETTINGS>  
4. Set the alarm action:  
BACK  
EXIT  
a. Use the joystick to position the cursor beside ALARM ACTION.  
b. Press Iris Open. The cursor moves to the right.  
c. Move the joystick up or down to view the available selections. The following are the  
settings for alarm action:  
NONE  
No action when alarm is triggered.  
PRESET  
The system goes to the preset that is the same as the alarm  
number. Preset 1 will go to Alarm 1.  
ALARM SETTINGS  
ALARM NUMBER  
1
PATTERN 1  
PATTERN 2  
PATTERN 3  
PATTERN 4  
The system runs pattern 1 when alarm is triggered.  
The system runs pattern 2 when alarm is triggered.  
The system runs pattern 3 when alarm is triggered.  
The system runs pattern 4 when alarm is triggered.  
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
LOW  
NONE  
NO  
ALARM CONTACT  
OFF  
BACK  
EXIT  
d. Press Iris Open to enter selection.  
Quick Programming Guide  
(See Page 9)  
C1301M (6/05)  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Set the auxiliary to activate:  
PELCO EXSITE EHXM  
a. Use the joystick to position the cursor beside ACTIVATE AUX.  
b. Press Iris Open. The cursor moves to the right.  
c. Move the joystick up or down to view the following available selections.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
NO (default)  
Not activated.  
1
2
An alarm action will close AUX 1.  
An alarm action will close AUX 2.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
d. Press Iris Open to enter selection.  
EXIT  
NOTE: The AUX 1/AUX2 will stop when all the alarms assigned to it have cleared. If the AUX1/AUX  
is set up as momentary, then it will be activated each time a new alarm is activated.  
6. Set the alarm contact:  
a. Use the joystick to position the cursor beside ALARM CONTACT.  
b. Press Iris Open. The cursor moves to the right.  
c. Move the joystick up or down to view the following available selections.  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
N/O (default) Normally open  
N/C  
Normally closed  
d. Press Iris Open to enter selection.  
<AUX>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
ALARMS  
RESUME  
SEQUENCE (SECS)  
RESET DELAY (SECS)  
OFF  
5
<ALARM SETTINGS>  
BACK  
EXIT  
ALARM SETTINGS  
ALARM NUMBER  
1
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
LOW  
NONE  
NO  
ALARM CONTACT  
OFF  
BACK  
EXIT  
30  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIPER  
The following EHXM unit models feature a window wiper to clear moisture from the window of the  
enclosure:  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
EHXM31C22-2  
EHXM31C22-2X  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
EHXM31C22-7  
EHXM31C22-7X  
EHXM31CBW23-2  
EHXM31CBW23-7  
EHXM31CBW23-2X  
EHXM31CBW23-7X  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
NOTE: The Wiper menu is only available on the above models. To check the unit model refer to the  
System Information section of this manual.  
EXIT  
WIPER CONTROL  
This feature programs the on/off control for the wiper. There are two available settings for wiper  
control, AUX 1 and Preset 86. If the wiper control is programmed for AUX 1, the wiper will operate  
when AUX 1 is accessed. If the wiper control is set to Preset 86, selecting preset 86 on your  
controller will turn the wiper on/off.  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
WIPER MODE  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
Wiper mode determines how the wiper will act after the wiper control is turned on/off. There are  
two modes of operation for wiper mode:  
<AUX>  
<CLEAR>  
<PASSWORD>  
MOMENTARY (default) Programs the wiper to move across the enclosure window once and  
then back to its starting position.  
BACK  
EXIT  
CONTINUOUS  
Programs the wiper to operate continually after the wiper is turned  
on. The wiper will continue to operate until the wiper control (AUX 1  
or preset 86) is pressed again or until the programmed wiper time is  
completed.  
WIPER*  
WIPER CONTROL  
WIPER MODE  
WIPER DWELL (SECS)  
WIPER TIME (MINS)  
AUX 1  
CONTINUOUS  
2
60  
WIPER DWELL  
<SET WASHER SEQUENCE>  
The wiper can be programmed to wipe the enclosure window every 2 to 30 seconds. This setting  
only works when the wiper is programmed for continuous mode. The dwell time can be programmed  
from 2 to 30 seconds.  
BACK  
EXIT  
WIPER TIME  
*AVAILABLE ONLY WITH THE WIPER MODELS.  
Wiper time programs how long the wiper will be on before it automatically shuts off. This setting  
only works when the wiper is programmed for continuous mode. Wiper time can be programmed  
from 60 to 1,440 minutes (1 to 24 hours).  
NOTE: CM9700 Matrix Systems Only – For the wiper to operate in continuous mode, the AUX 1  
function in the camera file must be set to latching in the CM9700-MGR. If the AUX 1 camera file is  
not latching, the wiper will only operate in momentary mode, even if the system wiper is  
programmed for continuous operation. Refer to the CM9700-MGR Software Guide for instructions.  
Quick Programming Guide  
(See Page 9)  
C1301M (6/05)  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
SET WASHER SEQUENCE  
An external washer (not supplied by Pelco) can be used to wash the window of the enclosure.  
Accessing AUX 3 or selecting Preset 87 will start the washer sequence.  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
Use the following steps to program the washer sequence.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
1. Use the joystick to position the cursor beside WIPER and then press Iris Open. The wiper menu  
appears on the monitor.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
2. Position the cursor beside SET WASHER SEQUENCE and then press Iris Open.  
3. Edit the preset label:  
EXIT  
a. Use the joystick to position the cursor beside EDIT PRESET LABEL.  
b. Press Iris Open. The following appears on the monitor:  
LABEL FOR PRESET WASH  
WASH - - - - - - - - - - - -  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
klmnopqrst  
uvwxyz#&:”  
OK  
CANCEL  
SPACE  
BACKSPACE  
<AUX>  
<CLEAR>  
<PASSWORD>  
c. Use the joystick to position the cursor beside a character. Press Iris Open to enter  
selection. To clear a character, position the cursor beside BACKSPACE, and then press  
Iris Open.  
BACK  
EXIT  
d. When the label is completed, move the cursor to OK. Press Iris Open to return to the Set  
Washer Sequence menu.  
WIPER*  
4. Edit the preset scene:  
WIPER CONTROL  
WIPER MODE  
AUX 1  
CONTINUOUS  
a. Use the joystick to position the cursor beside EDIT PRESET SCENE.  
b. Press Iris Open.  
WIPER DWELL (SECS)  
WIPER TIME (MINS)  
2
60  
c. Follow the directions displayed on the monitor.  
<SET WASHER SEQUENCE>  
5. Edit preset camera settings:  
a. Use the joystick to position the cursor beside EDIT CAMERA SETTINGS.  
b. Press Iris Open. The EDIT CAMERA SETTINGS window appears on the monitor. Refer to  
the Camera and Advanced Camera Settings sections of this manual to change camera  
settings.  
BACK  
EXIT  
6. Set the washer time. The washer time programs how long the wiper will be on before it  
automatically shuts off. Washer time can be programmed from 4 to 60 seconds.  
SET WASHER SEQUENCE  
* * * PRESET NOT DEFINED * * *  
7. Program the wiper delay. Wiper delay programs when the wiper will start after the washer  
sequence has started. Wiper delay can be programmed from 1 to 30 seconds.  
<EDIT PRESET LABEL>  
<EDOT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
8. Program the Auto Return to ON or OFF. If the auto return is set to ON the unit will return to the  
last position before the system started the washer sequence. If it is set to OFF, the system will  
remain at the preset scene for the washer sequence.  
WASHER TIME (SECS)  
WIPER DELAY (SECS)  
AUTO RETURN  
4
1
ON  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
BACK  
EXIT  
*Available only with the wiper models.  
32  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
AUX  
An auxiliary output is a programmable signal from the system that can trigger another device to  
operate. An auxiliary output is programmable to trigger from an alarm or from a controller.  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
An AUX 1 command from the controller will activate the relay in the system and operate the device  
that is connected to the relay. The output of AUX 1 and AUX 2 can be connected to the alarm input  
of a system switch to activate automatic monitor switching and recording.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
The following are the available AUX MODE settings:  
TOGGLE (default)  
Changes the state of the auxiliary output every time an AUX command is  
received from the controller.  
EXIT  
LATCHING  
Must receive an AUX ON/AUX OFF command from the controller to turn  
the auxiliary output on/off.  
MOMENTARY  
An AUX ON command from the controller turns the auxiliary output on  
for the programmed DWELL TIME. The auxiliary output will  
automatically turn off when the dwell time is finished.  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
AUX  
AUX 1 MODE  
DWELL TIME (SECS)  
TOGGLE  
1
AUX 2 MODE  
DWELL TIME (SECS)  
TOGGLE  
1
BACK  
EXIT  
Quick Programming Guide  
(See Page 9)  
C1301M (6/05)  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
CLEAR  
Use this setting to clear user-defined settings or return the system to factory default settings.  
PELCO EXSITE EHXM  
The following are the available CLEAR settings:  
LANGUAGE  
ENGLISH  
ALL PRESETS  
Clears all presets. To clear a single preset, refer to the  
Presets section.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
ALL PATTERNS  
Clears all patterns. To clear a single pattern, refer to the  
Patterns section.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ALL WINDOW BLANKING  
Clears all blanked windows. To clear a single blanked  
window, refer to the Window Blanking section.  
EXIT  
RESTORE FACTORY DEFAULTS Restores all camera settings to factory default settings.  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
CLEAR  
CLEAR ALL PRESETS  
CLEAR ALL PATTERNS  
CLEAR ALL WINDOW BLANKING  
RESTORE FACTORY DEFAULTS  
BACK  
EXIT  
34  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PASSWORD  
ExSite EHXM features password protection to prevent unauthorized changes to the system settings.  
An operator can open the System Information and Display Setup Screens, but cannot access any of  
the Unit Settings menus.  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
Controller/keyboard commands cannot override password-protected settings. If a keyboard is used  
to set a preset or pattern, the Enter Password screen appears on the monitor. The password must be  
entered before programming can continue.  
<UNIT SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
At least one character must be entered to create a valid password.  
EXIT  
UNIT SETTINGS  
<CAMERA>  
<OTHER>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<WINDOW BLANKING>  
<ALARMS>  
<WIPER>  
<AUX>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
PASSWORD  
ENABLE PASSOWRD  
<EDIT PASSWORD>  
OFF  
BACK  
EDIT THE PASSWORD  
- - - - - - - - - - - -  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
OK  
CANCEL  
SPACE  
BACKSPACE  
klmnopqrst  
uvwxyz#&:”  
Quick Programming Guide  
(See Page 9)  
C1301M (6/05)  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Reset, Cycle Power, Reboot  
RESET CAMERA  
PELCO EXSITE EHXM  
LANGUAGE  
ENGLISH  
Use this function to reset all camera settings to factory default parameters.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<UNIT SETTINGS>  
CYCLE CAMERA POWER  
RESET CAMERA  
If the camera is not operating or if you lose camera control, cycle camera power. Cycling camera  
power resets the camera but does not change any saved camera settings.  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
REBOOT SYSTEM  
Reboot the system if it is not operating or if there is no control. Rebooting the system will cycle pan  
and tilt and camera power without changing programmed settings.  
36  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Software/Language File Upload  
The ExSite EHXM system allows access for on-site setup, testing, and uploading of revised operating software and language files.  
A Pelco field service tool is required to perform these operations. Field service tools include Pelco’s remote monitor kit (IPS-RMK),  
remote data port box (IPS-RDPE-2), and remote monitor cable (IPS-CABLE).  
For instructions on how to upload revised operating software and language files refer to the Installation/Operation manual supplied  
with the field service tool.  
NOTE: Only perform software uploads when necessary. Software uploads do not need to be performed if the system is  
operating properly.  
UPLOAD ICON  
During a software/language file upload, an icon will appear on the monitor to indicate data is being transferred to the system (refer to  
the figure below). The default setting for data transmission is 115.2 KB per second. Noisy and long-run connections will slow the  
transmission rate.  
Upload Icon  
Quick Programming Guide  
(See Page 9)  
C1301M (6/05)  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Specifications  
Camera  
Day/Night (23X) Color  
NTSC, PAL  
LowLight™ (22X) Color  
NTSC, PAL  
Signal Format  
Scanning System  
Image Sensor  
2:1 interlace  
2:1 Interlace  
1/4-inch EXview HAD™ CCD  
1/4-inch CCD  
Effective pixels  
NTSC  
724 (H) x 494 (V)  
724 (H) x 582 (V)  
768 (H) x 494 (V)  
752 (H) x 582 (V)  
PAL  
Horizontal Resolution  
NTSC  
PAL  
>470 TV lines  
>470 TV lines  
>470 TV lines  
>460 TV lines  
Lens  
F1.6 (F = 3.6~82.8 mm optical)  
23X optical, 10X digital  
2.9/4.2/5.8 seconds  
F1.6 (F = 4~88 mm optical)  
22X optical, 12X digital  
2.4/3.9/6.3 seconds  
Zoom  
Zoom Speed  
Horizontal Angle of view  
54˚ at 3.6 mm wide zoom  
47˚ at 4.0 mm wide zoom  
2.5˚ at 82.8 mm telephoto zoom  
2.2˚ at 88 mm telephoto zoom  
Focus  
Automatic with manual override  
Automatic with manual override  
Maximum Sensitivity at  
35 IRE  
NTSC  
0.08 lux at 1/2 sec shutter (color)  
0.3 lux at 1/60 sec shutter (B-W)  
0.013 lux at 1/2 sec shutter (B-W)  
0.02 lux at 1/2 sec shutter  
0.02 lux at 1/1.5 sec shutter  
PAL  
0.08 lux at 1/1.5 sec shutter (color)  
0.3 lux at 1/50 sec shutter (B-W)  
0.013 lux at 1/1.5 sec shutter (B-W)  
Sync System  
Internal/AC line lock, phase adjustable via  
remote control, V-Sync*  
Internal/AC line lock, phase adjustable via remote  
control, V-Sync*  
White Balance  
Shutter Speed  
Automatic with manual override*  
Automatic (electronic iris)/Manual  
Automatic with manual override*  
Automatic (electronic iris)/Manual  
NTSC  
PAL  
1/2~1/30,000*  
1/2~1/30,000*  
1/1.5~1/30,000*  
1/1.5~1/30,000*  
Iris Control  
Automatic Iris Control with manual override*  
Automatic Iris Control with manual override*  
Gain Control  
Automatic/OFF*  
1 Vp-p, 75 ohms  
>50 dB  
Automatic/OFF*  
1 Vp-p, 75 ohms  
>50 dB  
Video Output  
Video Signal to Noise  
Wide Dynamic Range  
80X  
N/A  
*Manual control of camera setup functions can be done with CM6700, CM6800, CM8500, CM9500, CM9740, CM9760, CM9770,  
CM9780, KBD200A, KBD300A, and MPT9500 controllers, but not with CM7500, MPT9000 or KBD9000 controllers.  
38  
C1301M (6/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
•
•
•
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
•
•
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in  
continuous motion applications.  
•
•
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and Endura™ Series distributed network-based video products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelco’s liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
REVISION HISTORY  
Manual #  
Date  
Comments  
C1301M  
6/05  
Original version.  
Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco.  
LowLight, Endura and ExSite are trademarks of Pelco.  
©Copyright 2005, Pelco. All rights reserved.  
EXviewHAD is a trademark of the Sony Corporation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
www.pelco.com  
ISO9001  
United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East  
|
|
|
|
|
|
|
|
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peg Perego Stroller Aria Twin User Manual
Pelco Home Theater Server C551M User Manual
Philips Car Stereo System SA1VBE02 User Manual
Philips Cell Phone CT6558 User Manual
Philips Flat Panel Television PF9925 User Manual
Philips Headphones SBCHP430 User Manual
Philips Work Light Halogen Lamp User Manual
Pioneer Car Stereo System DEH 1650 User Manual
Pioneer Speaker System N30 User Manual
Pioneer Stereo Receiver VSX 1019AHK User Manual