®
MR5000L
Ceiling Monitor Mount
for the MR5000 Series
Public Viewing System
Installation/
Operation Manual
C221M-C (6/03)
USA & Canada: Tel: 800/289-9100 • Fax: 800/289-9150
International: Tel: 1-559/292-1981 • Fax: 1-559/348-1120
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
Refer to the following chart for recommended mounts, installation surfaces, and minimal
hardware requirements.
Mount Recommended Mounting Surface
Recommended Hardware
MRCA Solid Concrete*
Four 5/16 x 2 3/4-inch strike anchors
Ceiling
Mount
Wall board/2 x 4’s
Two 5/16 x 2-inch lag bolts (bolts must
be attached to stud)
Plywood (3/4-inch construction grade) Four 5/16 x 2-inch lag bolts
MRWA Solid Concrete*
Three 5/16 x 2 3/4-inch strike anchors
Three 5/16 x 2 1/2-inch T-anchors
Wall
Hollow cinder block
Wall board/2 x 4’s
Mount
Three 5/16 x 2-inch lag bolts (bolts must
be attached to stud)
Plywood (3/4-inch construction grade) Four 5/16 x 2-inch lag bolts
*Recommended strength of concrete is 3600 psi or 25 Mpa.
DESCRIPTION
Pelco’s MR5000 public viewing system is specifically designed for retail applications to
provide a clear, visual warning to potential shoplifters that these premises are under
surveillance. When properly installed the system is an effective deterrent against shoplifting.
Use the MR5000L to mount Pelco’s PMCS19A and PMC21A monitors and other view
station accessories (PCM5000 and ICS-DO101ABK) to a ceiling. The MR5000L can
support loads up to 66 pounds (29.94 kg).
Pelco Manual C221M-C (6/03)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
The following parts are supplied:
1
1
2
1
6
Mount arm
Rack base
Rack sides
1 1/2-inch NPT pipe
#8 x .50-inch, Phillips, pan head screws and finishing washers (use for PMC21A sides
and feet)
2
2
2
2
2
1
1
1
1
M4 x 12 mm, Phillips, pan head screws and washers (use for PMCS19A feet)
M6 x 12 mm, Phillips, pan head screws and washers (use for PMCS19A sides)
10-32 x .375-inch, Phillips, pan head screws and lock washers
5/16-18 x .75-inch hex bolts and lock washers
End caps for top and bottom of mount arm
.50-inch hole plug
3/16-inch Allen wrench
3/32-inch Allen wrench (for set screws)
4 cc tube of anti-seize
ᕡ Prepare Video and Electrical Cabling
CAUTION:
Refer to local
electrical codes
The MR5000L monitor mount is
TOP SET SCREW
SWIVEL COLLAR
(FEEDTHROUGH)
capable of providing a concealed wire
installation. To conceal cables, pull
cables through the feedthrough holes
of the mount arm. Refer to Figure 1
for feedthrough hole locations. To
feed cables through the top of the
swivel collar, temporarily remove the
top end cap from the mount arm (if
installed) to assist in directing cables.
before installing these units.
Local codes dictate how to
prepare wiring for all equip-
ment. Refer to Table A for
video coaxial cable
distances.
BOTTOM SET
SCREW
TOP END
CAP
FEEDTHROUGH
HOLE
FEEDTHROUGH
HOLE
FEEDTHROUGH FOR
ICS-DO101ABK
01120
Figure 1. MR5000L Mount Arm
Table A. Video Coaxial Cable Requirements
Cable Type*
Maximum Distance
RG59/U
RG6/U
750 ft (229 m)
1,000 ft (305 m)
1,500 ft (457 m)
RG11/U
*Minimum cable requirements:
75 ohms impedance
All-copper center conductor
All-copper braided shield with 95% braid coverage
4
Pelco Manual C221M-C (6/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ᕢ Install Mount Arm
NOTE: The bottom set
screw on the swivel collar is
for positioning the mount
arm. Refer to Figure 1.
Finish the installation before
adjusting the position of the
system.
a. Install the MRWA wall mount (not supplied) or MRCA ceiling mount (not supplied). For
installation surfaces and minimal hardware requirements, refer to page 2 of this manual.
b. Apply anti-seize to the threads of the 1 1/2-inch NPT pipe (provided). Thread the
swivel collar (at the top of the mount arm) onto the pipe.
c. Tighten the top set screw on the swivel collar (refer to Figure 1) to secure the mount to
the NPT pipe.
ᕣ Assemble Monitor Rack
The monitor used will dictate the position of the rack sides; refer to Figure 2. Position and
attach the rack sides to the mount base.
CONFIGURATION FOR THE PMCS19A
REAR
SIDE
FRONT
CONFIGURATION FOR THE PMC21A
REAR
SIDE
FRONT
01126
Figure 2. Monitor Rack Assembly
ᕤ Position and Attach Monitor Rack to Mount Arm
a. Place the monitor rack onto the bottom of the mount arm. Refer to Figure 3 and do the
following to properly position the rack on the mount arm:
PMCS19A - Use the ᕡ bolt hole position.
PMC21A - Use the ᕢ bolt hole position.
b. Use the 3/16-inch Allen wrench to secure the front of the monitor rack to the mount
arm with two 5/16-18 x .75-inch, Allen head bolts and locking washers. Secure the
back of the monitor rack with two 10-32 x .375-inch, black, Phillips, pan head screws
and locking washers.
1
ᕢ
01141
ᕡ3
Figure 3. Attach Rack to Mount Arm
Pelco Manual C221M-C (6/03)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ᕥ Install MR5000 Series Accessories
PCM5000 Light-Duty Camera Mount Assembly
a. The PCM5000 camera mount assembly can be installed on the top or bottom of the
MR5000M mount arm. To install the camera assembly onto the MR5000 Series
mount, refer to Figure 4 and do the following:
COLLAR SET
SCREWS
1. Pull video and electrical wire/
cable for the camera out
through the end of the mount
arm. Make all camera video
and electrical connections.
2. Place the end of the camera
assembly into the end of the
MR5000 Series monitor
mount arm. Tighten the set
MOUNT ARM
SET SCREW
01124
screws to secure the camera
assembly.
b. Refer to the manuals supplied with
Figure 4. PCM5000 Installation
the camera and the PCM5000 for
detailed installation and operation
instructions.
ICS-DO101ABK Camclosure Integrated Camera System
a. Refer to Figure 5 and do the following to attach the adapter plate of the ICS-DO101ABK
to the base of the ICS-DO101ABK:
1. Align the adapter plate to the base of the ICS-DO101ABK.
2. Use the two 10-32x .375-inch, pan head screws and internal lock washers to
attach the base of the ICS-DO101ABK to the adapter plate.
b. Prepare the video and electrical cabling for the ICS-DO101ABK:
1. Feed the 42-inch video cable (provided) through the monitor feedthrough hole in
the mount arm and out the end of the mount arm.
2. Pull power wires through the ICS-DO101ABK feedthrough (refer to Figure 1)
located at the bottom of the mount arm. Remove the .50-inch plug if it is installed.
3. Pull wires through the adapter plate of the ICS-DO101ABK and into the base of
the ICS-DO101ABK.
4. Use the supplied 3/16-inch Allen wrench to slightly loosen (do not remove) the
two 5/16-18 x .75-inch, Allen, pan head screws that secure the MR5000M mount
base to the mount arm.
5. Feed the video cable
attached to the
ICS-DO101ABK back box
through the ICS-
DO101ABK feedthrough in
the mount arm.
6. Hook the adapter plate
over the loosened screws
ADAPTER PLATE
(refer to Figure 5). Tighten
the screws to secure the
adapter plate to the mount.
CAMCLOSURE BASE
c. Refer to the manual supplied
with the ICS-DO101ABK for
detailed installation and
operation instructions.
NOTE: POSITION THE BASE SO THAT THE CONDUIT COVER
IS TURNED TOWARDS THE BACK OF THE MOUNT.
01125
Figure 5. ICS-DO101ABK Installation
6
Pelco Manual C221M-C (6/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ᕦ Prepare Monitor for Installation
NOTE: Reattach the back
feet to the monitor if it is
used in an installation other
than described in this
Refer to Figure 6 and remove the
monitor’s back feet and side screws.
manual. Only use the follow-
ing hardware to attach feet:
PMC21A
Two #8 x .50-inch Phillips
pan head screws and fin-
ishing washers (supplied,
see page 4)
PMCS19A
Two M4 x 12 mm Phillips
pan head screws and fin-
ishing washers (supplied,
see page 4)
Figure 6. Prepare Monitor
ᕧ Install Monitor
a. Verify that the monitor rack is level. Place the monitor onto the monitor rack. For
proper installation, the front feet of the monitor should be in the holes in the front of the
rack. Refer to Figure 7.
Do not use any other type of
hardware to attach the back
feet to the monitor.
b. Use the following hardware to secure the back of the monitor to the rack:
PMCS19A - Two M4 x 12 mm, black, Phillips, pan head screws (provided).
PMC21A - Two #8 x .50-inch, black, Phillips, pan head screws (provided).
c. Adjust the sides of the rack to fit against the sides of the monitor. Use the following
hardware to secure the monitor to the rack sides:
PMCS19A - Use the two M6 x 12 mm, Phillips, pan head screws and washers (provided).
PMC21A - Four #8 x .50-inch, black, Phillips, pan head screws (provided).
CAUTION:
Secure the mount
rack before install-
ing the monitor.
SECURE BOTH
SIDES OF MONITOR
WITH HARDWARE
FRONT FEET
OF MONITOR
MONITOR RACK
ANGLE ADJUSTMENT
SECURE BOTH
SIDES OF MONITOR
WITH HARDWARE
NOTE: THE POSITION OF THE FRONT FEET AND BACK FEET
MOUNT HOLES WILL VARY WITH MONITOR MODEL.
01121
Figure 7. Install Monitor
Pelco Manual C221M-C (6/03)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ᕨ Connect Video and Power to Monitor
a. Connect the video cable to the BNC video input on the rear panel of the monitor.
b. Plug the power cable into the AC INLET connection on the rear panel of the monitor.
Refer to the manual supplied with the monitor for operating instructions.
CAUTION:
Secure the monitor
to the rack before
adjusting the angle of the
rack.
ᕩ Final Adjustments
a. Monitor Rack - Refer to Figure 7 and adjust the monitor angle. The rack is adjustable
in 5-degree increments up to a 15-degree angle.
b. Mount Arm - Turn mount arm to desired position. Tighten the bottom set screw on the
swivel collar to secure in place.
WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one year after the date of shipment. Ex-
ceptions to this warranty are as noted below:
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100
or (559) 292-1981 to obtain a RepairAuthorization number (RA), and provide the
following information:
•
•
Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and
MC3500/MC3600 Series); two years on all other cameras.
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
Three years on Genex® Series (multiplexers, server, and keyboard) and
090 Series Camclosure® Camera System.
•
•
•
Two years on 100/150, 200, and 300 Series Camclosure Camera Systems.
Two years on all standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM6800E/CM8500/CM9500/
CM9740/CM9760 Matrix, DF5 and DF8 Series Fixed Dome products.
Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in
continuous motion applications.
If there is a dispute regarding the warranty of a product which does not fall under
the warranty conditions stated above, please include a written explanation with
the product when returned.
•
Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.
•
•
•
Two years on Esprit and WW5700 series window wiper (excluding wiper blades).
Eighteen months on DX Series digital video recorders.
One year (except video heads) on video cassette recorders (VCRs). Video heads
will be covered for a period of six months.
Six months on all pan and tilts, scanners or preset lenses used in continuous
motion applications (that is, preset scan, tour and auto scan modes).
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call
the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization num-
ber (CA number if returned for credit, and RA number if returned for repair).
•
All merchandise returned for credit may be subject to a 20% restocking and
refurbishing charge.
Pelco will warrant all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid
to Pelco, Clovis, California. Repairs made necessary by reason of misuse,
alteration, normal wear, or accident are not covered under this warranty.
Goods returned for repair or credit should be clearly identified with the assigned
CA or RA number and freight should be prepaid. Ship to the appropriate address
below.
Pelco assumes no risk and shall be subject to no liability for damages or loss
resulting from the specific use or application made of the Products. Pelco’s liability
for any claim, whether based on breach of contract, negligence, infringement of
any rights of any party or product liability, relating to the Products shall not exceed
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be
liable for any special, incidental or consequential damages (including loss of use,
loss of profit and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico:
Intermediate Consignee
American Overseas Air Freight
320 Beach Road
Burlingame, CA 94010
USA
Ultimate Consignee
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
USA
The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.
REVISION HISTORY
Manual #
C221M
C221M-A
C221M-B
C221M-C
Date
9/01
9/02
2/03
6/03
Comments
Original version.
Revised Important Safeguards and Warnings and added an installation warning.
Supplied hardware revised.
Added ETL Listing and revised Safeguards and Warnings.
® Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco.
© Copyright 2003, Pelco.
All rights reserved.
8
Pelco Manual C221M-C (6/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
|