Pelco Security Camera C3412M D User Manual

INSTALLATION/OPERATION  
®
Spectra IV and  
Spectra IV SE Series  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
C3412M-D (12/08)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C3412M-D (12/08)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Welcome  
Thank you for purchasing Pelco’s premier integrated dome system, Spectra® IV/Spectra IV SE. Your new system features a high  
resolution camera/optics package with programmable dome drive software.  
This manual is designed primarily to be a reference tool for the installation and operation of your system. Inside you will find  
information about features and commands, as well as a detailed menu tree and a quick start guide. Installation on page 7 provides  
information required to set up and install the dome drive. Please thoroughly familiarize yourself with the information in this manual  
before installing and using your system.  
6
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
This manual contains installation instructions only for the Spectra IV/Spectra IV SE dome drive. For complete installation  
instructions for a Spectra IV/Spectra IV SE dome system, refer to the installation manual shipped with the back box.  
SWITCH SETTINGS  
Before installing the dome drive, configure the receiver address, termination, and baud setting. The DIP switches used to  
configure these settings are located on the base of the dome drive.  
Figure 1 shows the default settings for the DIP switches. Switch SW1-1 (SW1, switch 1) is set to the ON position; all other  
switches are set to the OFF position.  
Refer to the following sections to set the address, termination, and baud settings for the dome drive.  
O N  
SW2  
1
2
3
3
4
4
5
5
6
6
7
7
8
8
9
10  
O N  
SW1  
1
2
Figure 1. Default Switch Settings  
SW1: RECEIVER ADDRESS  
Set the SW1 switches for the address of the dome drive. The following information is required to set the dome drive  
address:  
P-type control: The default address is 2. Refer to Table A on page 10 for address settings that use P-type control. The  
maximum number of receivers is 32.  
maximum number of receivers is 254.  
SW2 SWITCH 1: AD-32 PRESET SYSTEM  
SW2-1 should be set to the ON position if an AD-32 controller and Pelco’s TXB-AD translator board are used to control the  
dome system.  
SW2 SWITCH 2: CM9502 SETTING  
If a CM9502 matrix system is used with the dome drive, set SW2-2 to the ON position.  
C3412M-D (12/08)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
SW2 SWITCH 3: CONTROL SYSTEM COMPATIBILITY  
Coaxial Control Systems  
Although Spectra IV/Spectra IV SE dome systems can operate with coaxial control systems from many manufacturers, the  
system is designed for optimal performance with Pelco Coaxitron® control products within the length specified for coaxial  
cable.  
To compensate for coaxial control systems from other manufacturers, Pelco has provided DIP switch SW2-3. Setting  
SW2-3 to the ON position may improve dome control with these control systems.  
If you are using a Pelco Coaxitron controller, leave SW2-3 in the default OFF position.  
Notes:  
This coaxial control system compatibility feature is only available for dome drive revisions A4 and later (revisions A0  
and later for Spectra IV Horizon dome drives). The revision number can be found on the barcode label on the top of  
the dome drive. Software version 1.090 and later indicates this mode is available by placing an asterisk next to the  
switch number in the Dip Switch Information menu.  
In some configurations, Pelco CM9502 Series matrix systems use nonstandard Coaxitron commands for functions like  
pattern playback. If you experience problems with these functions, set SW2-3 to the ON position.  
Pelco P Protocol Control Systems  
To compensate for Pelco P protocol control systems from other manufacturers, set SW2-3 to the ON position. This may  
improve dome control with some of these control systems.  
SW2 SWITCHES 4–5: SERIAL PORT SETTINGS  
RS-422 Setting (Default)  
SW2-4 and SW2-5 should both be set to the OFF position for RS-422 setting.  
For control, only two wires should be connected to the RX- and RX+ connectors on the circuit board inside the back box. For  
bidirectional control, four wires should be connected to the RX-, RX+, TX-, and TX+ connectors on the circuit board inside  
the back box.  
RS-485, 4-Wire Setting  
SW2-4 should be set to OFF and SW2-5 should be set to ON if a 4-wire serial port connection is used with RS-485.  
Note: This setting is most commonly used with Pelco Endura® systems.  
RS-485, 2-Wire Setting  
SW2-4 and SW2-5 should both be set to the ON position if a 2-wire serial port connection is used with RS-485.  
This setting is used to allow the Spectra dome system to transmit and receive commands on the same pair of wires. Only  
two wires should be connected to the RX- and RX+ connectors on the circuit board inside the back box.  
8
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
SW2 SWITCHES 6–8: BAUD SETTINGS  
Pelco’s D-type controllers are set for 2400 baud. The default setting for the dome drive is 2400 baud. If you are using a  
Pelco D-type controller, do not reset SW2 switches 1–3 or SW2 switches 6–8.  
P-type controllers can operate at 2400, 4800, and 9600 baud. Set the SW2 switches (6, 7, and 8), located on the base of  
the dome drive, to the same baud as the P-type controller.  
Switch Number  
SW2-6  
Off  
SW2-7  
Off  
SW2-8  
Off  
2400 Baud (default for D-type control)  
4800 Baud (default for P-type control)  
9600 Baud  
On  
Off  
Off  
Off  
On  
Off  
SW2 Switch 9: Coaxial/UTP Cable  
SW2-9 should be set to the OFF position (default) if you are using coaxial cable. If you are using unsheilded twisted pair  
(UTP) cable, set SW2-9 to the ON position.  
SW2 Switch 10: Termination Setting  
When connecting more than one Spectra IV/Spectra IV SE dome system to a single controller, terminate the unit farthest  
from the controller. Termination is only required for the last dome in the series.  
The dome drive is shipped from the factory in the unterminated (OFF) position. To terminate the dome drive, set SW2-10 to  
the ON position.  
Note: Dome termination is not required for Coaxitron® control.  
DOME DRIVE INSTALLATION  
Install the dome drive. Align the blue and red tabs with the blue and red arrows on the hinged door inside the back box.  
Push the tabs in. Insert one side and then the other side. Continue pushing on the ends of the tabs until both sides click  
into place (refer to Figure 2). To use your dome system, refer to Getting Started on page 19.  
Figure 2. Dome Drive Installation  
Note: When removing a dome drive that has been in use, caution should be taken to avoid direct contact with the top  
plate of the unit. This section of the unit will be warm to the touch when first removed from an operating unit.  
C3412M-D (12/08)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Table A. Switch Settings for SW1 P-Type Control  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW1-1  
OFF  
ON  
SW1-2  
OFF  
OFF  
ON  
SW1-3  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-4  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-5  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-6  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
SW1-7  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
SW1-8  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
1
2
3
OFF  
ON  
4
ON  
5
OFF  
ON  
OFF  
OFF  
ON  
6
ON  
7
OFF  
ON  
ON  
8
ON  
ON  
9
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
10  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Table B. Switch Settings for SW1 D-Type Control  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW1-1  
ON  
SW1-2  
OFF  
ON  
SW1-3  
OFF  
OFF  
OFF  
ON  
SW1-4  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-5  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-6  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-7  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
SW1-8  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
1
2
OFF  
ON  
3
ON  
4
OFF  
ON  
OFF  
OFF  
ON  
5
ON  
6
OFF  
ON  
ON  
7
ON  
ON  
8
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
9
ON  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
C3412M-D (12/08)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Table B. Switch Settings for SW1 D-Type Control (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW1-1  
OFF  
ON  
SW1-2  
OFF  
OFF  
ON  
SW1-3  
ON  
SW1-4  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-5  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-6  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
SW1-7  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-8  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
12  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table B. Switch Settings for SW1 D-Type Control (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW1-1  
ON  
SW1-2  
ON  
SW1-3  
ON  
SW1-4  
OFF  
ON  
SW1-5  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-6  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-7  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
SW1-8  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
92  
93  
94  
95  
96  
97  
98  
99  
100  
101  
102  
103  
104  
105  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
C3412M-D (12/08)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table B. Switch Settings for SW1 D-Type Control (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW1-1  
OFF  
ON  
SW1-2  
ON  
SW1-3  
OFF  
OFF  
ON  
SW1-4  
ON  
SW1-5  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-6  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
SW1-7  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
SW1-8  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
106  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
121  
122  
123  
124  
125  
126  
127  
128  
129  
130  
131  
132  
133  
134  
135  
136  
137  
138  
139  
140  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
ON  
14  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table B. Switch Settings for SW1 D-Type Control (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW1-1  
ON  
SW1-2  
OFF  
ON  
SW1-3  
ON  
SW1-4  
ON  
SW1-5  
OFF  
OFF  
OFF  
ON  
SW1-6  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-7  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
SW1-8  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
141  
142  
143  
144  
145  
146  
147  
148  
149  
150  
151  
152  
153  
154  
155  
156  
157  
158  
159  
160  
161  
162  
163  
164  
165  
166  
167  
168  
169  
170  
171  
172  
173  
174  
175  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
C3412M-D (12/08)  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table B. Switch Settings for SW1 D-Type Control (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW1-1  
OFF  
ON  
SW1-2  
OFF  
OFF  
ON  
SW1-3  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-4  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-5  
ON  
SW1-6  
ON  
SW1-7  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-8  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
176  
177  
178  
179  
180  
181  
182  
183  
184  
185  
186  
187  
188  
189  
190  
191  
192  
193  
194  
195  
196  
197  
198  
199  
200  
201  
202  
203  
204  
205  
206  
207  
208  
209  
210  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
OFF  
ON  
ON  
16  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table B. Switch Settings for SW1 D-Type Control (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW1-1  
ON  
SW1-2  
ON  
SW1-3  
OFF  
ON  
SW1-4  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
SW1-5  
ON  
SW1-6  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
SW1-7  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
SW1-8  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
211  
212  
213  
214  
215  
216  
217  
218  
219  
220  
221  
222  
223  
224  
225  
226  
227  
228  
229  
230  
231  
232  
233  
234  
235  
236  
237  
238  
239  
240  
241  
242  
243  
244  
245  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
C3412M-D (12/08)  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table B. Switch Settings for SW1 D-Type Control (Continued)  
SWITCH SETTING  
SPECTRA  
ADDRESS  
SW1-1  
OFF  
ON  
SW1-2  
ON  
SW1-3  
ON  
SW1-4  
OFF  
OFF  
ON  
SW1-5  
ON  
SW1-6  
ON  
SW1-7  
ON  
SW1-8  
ON  
246  
247  
248  
249  
250  
251  
252  
253  
254  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
18  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting Started  
Once installed, apply power to the Spectra IV/Spectra IV SE dome system. The system will start a configuration sequence.  
When configuration is done, the following information is displayed:  
Pelco Spectra IV/Spectra IV SE  
Version X.XX  
D Address: 1  
P Address: 2  
Comm 2400, N, 8, 1  
CONFIGURE DONE  
This information will remain on the monitor until dome operation begins.  
Note: When installing a Spectra IV dome drive in a Spectra IIIback box for the first time, a message appears. When the  
installation is complete, the dome drive will continue with a normal configuration sequence.  
C3412M-D (12/08)  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
How to Operate Your Dome System  
Operation  
Pan and Tilt  
Zoom Far  
How to Control  
Move the joystick or press the direction keys left/right and up/down.  
To zoom far:  
1. Press the Zoom Tele button or turn the joystick clockwise until zoom stops at the optical zoom  
limit.  
2. Release the button or joystick for one second.  
3. To continue zooming (digitally), press the button or turn the joystick clockwise again until you  
have the picture you want or reach the digital zoom1 limit.  
Zoom Wide  
Scanning  
Press the Zoom Wide button or turn the joystick counterclockwise.  
Stop Scan  
Preset 96  
Preset 97  
Preset 98  
Preset 99  
Random Scan  
Frame Scan  
Auto Scan  
Presets  
Patterns2  
Zones  
Refer to the documentation supplied with the control system.  
Refer to the documentation supplied with the control system.  
Refer to Zones on page 64 and to the documentation supplied with the control system.  
Refer to Alarms on page 68.  
Alarms  
Auto Flip  
Turn on or off in the programming menu. Refer to Auto Flip on page 50.  
1 Digital zoom magnifies the image electronically and the picture may appear pixilated. The larger the digital zoom limit the greater the  
reduction in resolution.  
2 The dome cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern.  
20  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
QUICK PROGRAMMING GUIDE  
Access main menu (preset 95). Refer to Accessing Main Menu (Preset 95) on page 21.  
Use the joystick to position the cursor beside menu selection.  
Note: If your controller does not have a joystick, use the up or down key.  
Press Iris Open, the submenu/cursor moves to the right.  
Move the joystick up or down to view selections.  
Press Iris Open to make a selection.  
Press Iris Close to cancel a selection.  
ACCESSING MAIN MENU (PRESET 95)  
You can call up the main menu on your monitor by programming (setting or creating) preset 95 (preset 28 in AD32-preset  
mode).  
Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for  
programming preset 95 are given below for various Pelco controllers.  
CM6700/CM6800  
1. Enter the number of the Spectra IV/Spectra IV SE dome system and press the CAM key.  
2. Enter 95 and hold the PRESET key for two seconds.  
3. In the Edit Preset menu, go to SET and press the ACK key. The main menu appears.  
KBD200A/KBD300A (Direct Mode Only)  
1. Enter 95.  
2. Hold the PRESET key (approximately five seconds) until the main menu appears on the screen.  
C3412M-D (12/08)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
CM9500  
1. Enter the number of the Spectra IV/Spectra IV SE dome system and press the CAM key. The main menu appears.  
2. Highlight SETUP in the main menu and press the SELECT key.  
3. Highlight CAM in the Setup menu and press the SELECT key.  
4. Highlight PRESET in the Camera menu and press the SELECT key.  
5. Enter 95 and press the F1 key. The main menu appears.  
CM9740/CM9760/CM9770/CM9780  
1. Press the ESCAPE key to open the main menu. Select DEF. The Define submenu appears.  
2. Enter your four-digit PIN if this is your first time entering this mode.  
3. Enter 95 and select PRST. The main menu appears on the monitor.  
4. Select the Quit icon to return to the default menu.  
KBD4000/KBD4002  
1. Press the SPOT MONITOR key.  
2. Enter 95, then hold the PRESET key (approximately five seconds) until the main menu appears on the screen.  
MPT9500  
Standard Coaxitron Mode  
1. Enter 95 and press the PRESET SET key.  
2. Position the asterisk in the YES row and press the F1 key. The main menu appears.  
Extended Coaxitron or RS-485 Mode  
1. Enter 95 and press the PRESET SET key.  
2. Press the F2 key. The main menu appears.  
22  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
NET300/NET350/NET4001A  
1. Check the Set box.  
2. Click the preset 95 button. The main menu appears.  
ENDURA WORKSTATION  
1. Right-click in the video pane of the Spectra IV/Spectra IV SE dome system.  
2. Click Preset and then click Select Preset.  
3. Enter 95 and then click OK.  
VCD5000  
1. Enter 95 for the preset action. The shortcuts menu appears.  
2. Press the Preset button on the KBD5000.  
C3412M-D (12/08)  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
16X LowLight Color Menu Tree  
SPECTRA IV  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
SYSTEM INFORMATION  
DISPLAY SETUP  
SERIAL #  
XXXXXXXXXXXXXX  
XX-XXXX  
PRESET LABEL  
2 (SECS)  
2 (SECS)  
2 (SECS)  
2 (SECS)  
OFF  
DOME DRIVE MODEL  
BACK BOX MEMORY  
SOFTWARE VERSION  
BUILD  
ZONE LABEL  
ZOOM  
AVAILABLE  
XX.X  
AZIMUTH/ELEVATION  
DIRECTION  
FONT VERSION  
COMM  
XX.X  
ALARM MESSAGE  
DATE/TIME  
2 (SECS)  
ON  
XXXXXXXXXX  
D ADDRESS  
1
2
EVENT LABEL  
2 (SECS)  
P ADDRESS  
CM95OO MODE  
32 PRESETS  
OFF  
OFF  
C
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
PROTOCOL  
DIPSWITCH INFORMATION  
PRESSURIZED*  
<ADDITIONAL>  
X.XX  
LABEL POSITION  
12345678  
1234567890  
SW1[--------] SW2[----------]  
[ZONE LABEL-------]  
[PRESET LABEL-------]  
[ALARM 1-------]  
ADDITIONAL  
SW1 1-8:  
D ADDRESS 1  
FREE MEMORY  
LATEST RESET  
XXXXXX  
[ALERT MESSAGE---]*  
P ADDRESS 1  
POWER ON  
SW2 1 : 32 PRESETS. OFF  
SW2 2 : CM9500 MODE. OFF  
SW2 3 : COAX SPIV  
SW2 4-5 : RS422 <->  
AZIMUTH ZERO OFFSET  
MOTOR ACTIVE  
CAMERA ACTIVE  
VIDEO LEVEL  
0°  
YES  
SAVE AND EXIT  
CANCEL AND EXIT  
HELP  
YES  
NORMAL  
XXXX-XXXX  
ENGLISH X.XX  
XXX/-XX  
SW2 6-8 : COMM. 2400.N.8.1  
SW2 9 : UTC SOURCE. COAX  
SW2 10 : TX/RX TERM.. OFF  
CAMERA MODEL  
LANGUAGE 1  
NE  
XXX.XX  
. . .  
LANGUAGE 10  
ITALIANO X.XX  
PRESS IRIS OPEN TO CONTINUE  
<DIPSWITCH INFORMATION>  
CAMERA  
ADVANCED SETTINGS  
MOTION  
POWER UP  
AUTO FOCUS  
SURE FOCUS  
ZOOM LIMIT  
ON  
OFF  
SUTTER SPEED  
AGC LIMIT  
AUTO  
28  
AUTO FLIP  
ON  
ON  
POWER UP ACTION  
AUTO  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
XXXX  
AUTO IRIS  
AUTO  
66  
0
ZOOM SPEED  
LOW LIGHT LIMIT  
XXXX  
XXXXXX  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
NONE  
25  
AUTO  
ON  
8
ON  
26  
ON  
255  
255  
OFF  
HIGH  
SCAN SPEED DEG/S  
PRESET FREEZE FRAME  
LIMIT STOPS  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
<ADVANCED SETTINGS>  
ZONES  
WINDOW BLANKING  
SET WINDOWS  
ALARMS  
ZONE NUMBER  
1
STYLE  
GRAY  
OFF  
OFF  
WINDOW NUMBER  
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
<EDIT SCHEDULE>  
ENABLE WINDOW  
REVERSE  
1
ALARM CONTACT  
***ZONE NOT DEFINED***  
<EDIT ZONE LABEL>  
<EDIT ZONE>  
BLANK ALL ABOVE  
BLANK ALL BELOW  
<SET WINDOWS>  
NO  
ZONE ENABLED  
ZONE BLANKING  
<CLEAR ZONE>  
ON  
OFF  
CLEAR WINDOW  
ALERT*  
REPEAT  
CURRENT READING  
CLEAR  
PASSWORD  
CONSTANT  
TEMPERATURE  
DEWPOINT  
PRESURE  
CLEAR ALL ZONES  
ENABLE PASSWORD  
<EDIT PASSWORD>  
OFF  
ACK ACTION  
ALWAYS ON  
CLEAR ALL PRESETS  
CLEAR ALL PATTERNS  
ACTIVATE AUX  
<CURRENT READING>  
RESET ALERT  
NO  
REFRESH  
CLEAR ALL WINDOW BLANKING  
CLEAR ALL EVENTS  
RESTORE FACTORY DEFAULTS  
*This setting applies only to Pressurized Spectra IV dome systems. Spectra IV systems that are not pressurized will not display this menu item.  
24  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
LINE SYNC  
PRESETS  
PATTERNS  
LINE SYNC  
LINE SYNC PHASE  
ON  
0
PRESET NUMBER  
1
PATTERN NUMBER  
1
***PRESET NOT DEFINED***  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT SCHEDULE>  
<CLEAR PRESET>  
<PROGRAM PATTERN>  
<CLEAR PATTERN>  
<EDIT SCHEDULE>  
REFERENCE INFO  
PATTERN USAGE  
REMAINING  
0%  
100%  
<CLEAR CAMERA SETTINGS>  
REFERENCE INFORMATION  
AZIMUTH  
ELEVATION  
ZOOM  
AUX  
TITLE TEXT  
AUX 1 MODE  
TOGGLE  
ENABLE TITLE TEXT  
<EDIT TITLE TEXT>  
DWELL TIME (SECS)  
AUX 2 MODE  
1
TOGGLE  
1
DWELL TIME (SECS)  
<EDIT SCHEDULE>  
EDIT THE PASSWORD  
CLOCK  
EVENT  
EDIT EVENT  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
klmnopqrst  
uvwxyz#&:*  
TIME BASE  
INTERNAL CLOCK  
12 HOUR  
EVENT TYPE  
ALL EVENTS  
EVENT LABEL  
EVENT01  
TIME FORMAT  
SET TIME  
EVENT LABEL  
NEW  
12:00 AM  
EVENT ACTIVE  
EVENT TIME  
EVENT OCCURS  
SUNDAY  
ON  
12:00 AM  
DATE FORMAT  
SET DATE  
DAYLIGHT SAVINGS  
MM/DD/YYYY  
00/00/0000  
OFF  
<EDIT EVENT LABEL>  
<EDIT EVENT>  
<CLEAR EVENT>  
<LIST EVENT>  
ON  
MONDAY  
ON  
TUESDAY  
ON  
HOLIDAY  
WEDNESDAY  
THURSDAY  
FRIDAY  
ON  
<EDIT HOLIDAY>  
<CLEAR HOLIDAY>  
<LIST HOLIDAYS>  
ON  
ON  
ON  
SATURDAY  
HOLIDAY  
SKIP HOLIDAYS  
EVENT TYPE  
PRESET  
C3412M-D (12/08)  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18X LowLight Day/Night Menu Tree  
SPECTRA IV  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
SYSTEM INFORMATION  
DISPLAY SETUP  
SERIAL #  
XXXXXXXXXXXXXX  
XX-XXXX  
PRESET LABEL  
2 (SECS)  
2 (SECS)  
2 (SECS)  
2 (SECS)  
OFF  
DOME DRIVE MODEL  
BACK BOX MEMORY  
SOFTWARE VERSION  
BUILD  
ZONE LABEL  
ZOOM  
AVAILABLE  
XX.X  
AZIMUTH/ELEVATION  
DIRECTION  
FONT VERSION  
COMM  
XX.X  
ALARM MESSAGE  
DATE/TIME  
2 (SECS)  
ON  
XXXXXXXXXX  
D ADDRESS  
1
2
EVENT LABEL  
2 (SECS)  
P ADDRESS  
CM95OO MODE  
32 PRESETS  
OFF  
OFF  
C
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
PROTOCOL  
DIPSWITCH INFORMATION  
PRESSURIZED*  
<ADDITIONAL>  
X.XX  
LABEL POSITION  
12345678  
1234567890  
SW1[--------] SW2[----------]  
[ZONE LABEL-------]  
[PRESET LABEL-------]  
[ALARM 1-------]  
ADDITIONAL  
SW1 1-8:  
D ADDRESS 1  
FREE MEMORY  
LATEST RESET  
AZIMUTH ZERO OFFSET  
MOTOR ACTIVE  
CAMERA ACTIVE  
VIDEO LEVEL  
XXXXXX  
POWER ON  
0°  
[ALERT MESSAGE---]*  
P ADDRESS 1  
SW2 1 : 32 PRESETS. OFF  
SW2 2 : CM9500 MODE. OFF  
SW2 3 : COAX SPIV  
SW2 4-5 : RS422 <->  
SAVE AND EXIT  
CANCEL AND EXIT  
HELP  
YES  
YES  
NORMAL  
XXXX-XXXX  
ENGLISH X.XX  
XXX/-XX  
SW2 6-8 : COMM. 2400.N.8.1  
SW2 9 : UTC SOURCE. COAX  
SW2 10 : TX/RX TERM.. OFF  
CAMERA MODEL  
LANGUAGE 1  
NE  
XXX.XX  
. . .  
LANGUAGE 10  
ITALIANO X.XX  
PRESS IRIS OPEN TO CONTINUE  
<DIPSWITCH INFORMATION>  
CAMERA  
ADVANCED SETTINGS  
MOTION  
POWER UP  
AUTO FOCUS  
ON  
OFF  
SUTTER SPEED  
AGC LIMIT  
AUTO  
28  
AUTO FLIP  
ON  
ON  
POWER UP ACTION  
AUTO  
SURE FOCUS  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
ZOOM LIMIT  
XXXX  
XXXX  
XXXXXX  
XXXX  
OFF  
AUTO IRIS  
AUTO  
66  
0
ZOOM SPEED  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
NONE  
25  
AUTO  
ON  
LOW LIGHT LIMIT  
IR CUT FILTER  
8
ON  
26  
ON  
255  
255  
OFF  
HIGH  
OFF  
ON  
SCAN SPEED DEG/S  
PRESET FREEZE FRAME  
LIMIT STOPS  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
<ADVANCED SETTINGS>  
AUTO  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
FIELD ALIGN  
LOW LUX NOISE REDUCTION  
ZONES  
WINDOW BLANKING  
SET WINDOWS  
ZONE NUMBER  
1
STYLE  
GRAY  
OFF  
OFF  
WINDOW NUMBER  
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
<EDIT SCHEDULE>  
ENABLE WINDOW  
REVERSE  
1
***ZONE NOT DEFINED***  
<EDIT ZONE LABEL>  
<EDIT ZONE>  
BLANK ALL ABOVE  
BLANK ALL BELOW  
<SET WINDOWS>  
NO  
ZONE ENABLED  
ZONE BLANKING  
<CLEAR ZONE>  
ON  
OFF  
CLEAR WINDOW  
ALERT*  
REPEAT  
CURRENT READING  
CLEAR  
PASSWORD  
CONSTANT  
TEMPERATURE  
DEWPOINT  
PRESURE  
CLEAR ALL ZONES  
ENABLE PASSWORD  
<EDIT PASSWORD>  
OFF  
ACK ACTION  
ALWAYS ON  
CLEAR ALL PRESETS  
CLEAR ALL PATTERNS  
ACTIVATE AUX  
<CURRENT READING>  
RESET ALERT  
NO  
REFRESH  
CLEAR ALL WINDOW BLANKING  
CLEAR ALL EVENTS  
RESTORE FACTORY DEFAULTS  
*This setting applies only to Pressurized Spectra IV dome systems. Spectra IV systems that are not pressurized will not display this menu item.  
26  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
LINE SYNC  
PRESETS  
PATTERNS  
LINE SYNC  
LINE SYNC PHASE  
ON  
0
PRESET NUMBER  
1
PATTERN NUMBER  
1
***PRESET NOT DEFINED***  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<EDIT SCHEDULE>  
<CLEAR PRESET>  
<PROGRAM PATTERN>  
<CLEAR PATTERN>  
<EDIT SCHEDULE>  
REFERENCE INFO  
PATTERN USAGE  
REMAINING  
0%  
100%  
<CLEAR CAMERA SETTINGS>  
REFERENCE INFORMATION  
AZIMUTH  
ELEVATION  
ZOOM  
ALARMS  
AUX  
TITLE TEXT  
ALARM CONTACT  
AUX 1 MODE  
TOGGLE  
ENABLE TITLE TEXT  
<EDIT TITLE TEXT>  
DWELL TIME (SECS)  
AUX 2 MODE  
1
TOGGLE  
1
DWELL TIME (SECS)  
<EDIT SCHEDULE>  
EDIT THE PASSWORD  
CLOCK  
EVENT  
EDIT EVENT  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
klmnopqrst  
uvwxyz#&:*  
TIME BASE  
INTERNAL CLOCK  
12 HOUR  
EVENT TYPE  
ALL EVENTS  
EVENT LABEL  
EVENT01  
TIME FORMAT  
SET TIME  
EVENT LABEL  
NEW  
12:00 AM  
EVENT ACTIVE  
EVENT TIME  
EVENT OCCURS  
SUNDAY  
ON  
12:00 AM  
DATE FORMAT  
SET DATE  
DAYLIGHT SAVINGS  
MM/DD/YYYY  
00/00/0000  
OFF  
<EDIT EVENT LABEL>  
<EDIT EVENT>  
<CLEAR EVENT>  
<LIST EVENT>  
ON  
MONDAY  
ON  
TUESDAY  
ON  
HOLIDAY  
WEDNESDAY  
THURSDAY  
FRIDAY  
ON  
<EDIT HOLIDAY>  
<CLEAR HOLIDAY>  
<LIST HOLIDAYS>  
ON  
ON  
ON  
SATURDAY  
HOLIDAY  
SKIP HOLIDAYS  
EVENT TYPE  
PRESET  
C3412M-D (12/08)  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22X EXview LowLight Color Menu Tree  
SPECTRA IV  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
SYSTEM INFORMATION  
DISPLAY SETUP  
SERIAL #  
XXXXXXXXXXXXXX  
XX-XXXX  
PRESET LABEL  
2 (SECS)  
2 (SECS)  
2 (SECS)  
2 (SECS)  
OFF  
DOME DRIVE MODEL  
BACK BOX MEMORY  
SOFTWARE VERSION  
BUILD  
ZONE LABEL  
ZOOM  
AVAILABLE  
XX.X  
AZIMUTH/ELEVATION  
DIRECTION  
FONT VERSION  
COMM  
XX.X  
ALARM MESSAGE  
DATE/TIME  
2 (SECS)  
ON  
XXXXXXXXXX  
D ADDRESS  
1
2
EVENT LABEL  
2 (SECS)  
P ADDRESS  
CM95OO MODE  
32 PRESETS  
OFF  
OFF  
C
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
PROTOCOL  
DIPSWITCH INFORMATION  
PRESSURIZED*  
<ADDITIONAL>  
X.XX  
LABEL POSITION  
12345678  
1234567890  
SW1[--------] SW2[----------]  
[ZONE LABEL-------]  
[PRESET LABEL-------]  
[ALARM 1-------]  
ADDITIONAL  
SW1 1-8:  
D ADDRESS 1  
FREE MEMORY  
LATEST RESET  
XXXXXX  
[ALERT MESSAGE---]*  
P ADDRESS 1  
POWER ON  
SW2 1 : 32 PRESETS. OFF  
SW2 2 : CM9500 MODE. OFF  
SW2 3 : COAX SPIV  
SW2 4-5 : RS422 <->  
AZIMUTH ZERO OFFSET  
MOTOR ACTIVE  
CAMERA ACTIVE  
VIDEO LEVEL  
0°  
YES  
SAVE AND EXIT  
CANCEL AND EXIT  
HELP  
YES  
NORMAL  
XXXX-XXXX  
ENGLISH X.XX  
XXX/-XX  
SW2 6-8 : COMM. 2400.N.8.1  
SW2 9 : UTC SOURCE. COAX  
SW2 10 : TX/RX TERM.. OFF  
CAMERA MODEL  
LANGUAGE 1  
NE  
XXX.XX  
. . .  
LANGUAGE 10  
ITALIANO X.XX  
PRESS IRIS OPEN TO CONTINUE  
<DIPSWITCH INFORMATION>  
CAMERA  
ADVANCED SETTINGS  
MOTION  
POWER UP  
TYPE OF LIGHTING  
AUTO FOCUS  
T1  
ON  
SUTTER SPEED  
AGC LIMIT  
AUTO  
28  
AUTO FLIP  
ON  
ON  
POWER UP ACTION  
AUTO  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
SURE FOCUS  
OFF  
AUTO IRIS  
AUTO  
66  
0
ZOOM LIMIT  
XXXX  
XXXX  
XXXXXX  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
NONE  
25  
AUTO  
ON  
ZOOM SPEED  
8
ON  
26  
ON  
255  
255  
OFF  
SCAN SPEED DEG/S  
PRESET FREEZE FRAME  
LIMIT STOPS  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
LOW LIGHT LIMIT  
<ADVANCED SETTINGS>  
B GAIN  
BACKLIGHT COMP  
ZONES  
WINDOW BLANKING  
SET WINDOWS  
ZONE NUMBER  
1
STYLE  
GRAY  
OFF  
OFF  
WINDOW NUMBER  
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
<EDIT SCHEDULE>  
ENABLE WINDOW  
REVERSE  
1
***ZONE NOT DEFINED***  
<EDIT ZONE LABEL>  
<EDIT ZONE>  
BLANK ALL ABOVE  
BLANK ALL BELOW  
<SET WINDOWS>  
NO  
ZONE ENABLED  
ZONE BLANKING  
<CLEAR ZONE>  
ON  
OFF  
CLEAR WINDOW  
ALERT*  
REPEAT  
CURRENT READING  
CLEAR  
PASSWORD  
CONSTANT  
TEMPERATURE  
DEWPOINT  
PRESURE  
CLEAR ALL ZONES  
ENABLE PASSWORD  
<EDIT PASSWORD>  
OFF  
ACK ACTION  
ALWAYS ON  
CLEAR ALL PRESETS  
CLEAR ALL PATTERNS  
ACTIVATE AUX  
<CURRENT READING>  
RESET ALERT  
NO  
REFRESH  
CLEAR ALL WINDOW BLANKING  
CLEAR ALL EVENTS  
RESTORE FACTORY DEFAULTS  
*This setting applies only to Pressurized Spectra IV dome systems. Spectra IV systems that are not pressurized will not display this menu item.  
28  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
LINE SYNC  
PRESETS  
PATTERNS  
LINE SYNC  
LINE SYNC PHASE  
ON  
0
PRESET NUMBER  
1
PATTERN NUMBER  
1
***PRESET NOT DEFINED***  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<EDIT SCHEDULE>  
<PROGRAM PATTERN>  
<CLEAR PATTERN>  
<EDIT SCHEDULE>  
REFERENCE INFO  
PATTERN USAGE  
REMAINING  
0%  
100%  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
REFERENCE INFORMATION  
AZIMUTH  
ELEVATION  
ZOOM  
CUSTOM CAMERA SETTINGS  
ALARMS  
ALARM SETTINGS  
AUX  
TITLE TEXT  
RESUME  
OFF  
5
0
ALARM NUMBER  
1
LOW  
NONE  
NO  
AUX 1 MODE  
TOGGLE  
ENABLE TITLE TEXT  
<EDIT TITLE TEXT>  
SEQUENCE (SECS)  
RESET DELAY (SECS)  
<ALARM SETTINGS>  
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
DWELL TIME (SECS)  
AUX 2 MODE  
1
TOGGLE  
1
DWELL TIME (SECS)  
<EDIT SCHEDULE>  
ALARM CONTACT  
<EDIT SCHEDULE>  
N/O  
EDIT THE PASSWORD  
CLOCK  
EVENT  
EDIT EVENT  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
klmnopqrst  
uvwxyz#&:*  
TIME BASE  
INTERNAL CLOCK  
12 HOUR  
EVENT TYPE  
ALL EVENTS  
EVENT LABEL  
EVENT01  
TIME FORMAT  
SET TIME  
EVENT LABEL  
NEW  
12:00 AM  
EVENT ACTIVE  
EVENT TIME  
EVENT OCCURS  
SUNDAY  
ON  
12:00 AM  
DATE FORMAT  
SET DATE  
DAYLIGHT SAVINGS  
MM/DD/YYYY  
00/00/0000  
OFF  
<EDIT EVENT LABEL>  
<EDIT EVENT>  
<CLEAR EVENT>  
<LIST EVENT>  
ON  
MONDAY  
ON  
TUESDAY  
ON  
HOLIDAY  
WEDNESDAY  
THURSDAY  
FRIDAY  
ON  
<EDIT HOLIDAY>  
<CLEAR HOLIDAY>  
<LIST HOLIDAYS>  
ON  
ON  
ON  
SATURDAY  
HOLIDAY  
SKIP HOLIDAYS  
EVENT TYPE  
PRESET  
C3412M-D (12/08)  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23X LowLight Day/Night Menu Tree  
SPECTRA IV  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
SYSTEM INFORMATION  
DISPLAY SETUP  
SERIAL #  
XXXXXXXXXXXXXX  
XX-XXXX  
PRESET LABEL  
2 (SECS)  
2 (SECS)  
2 (SECS)  
2 (SECS)  
OFF  
DOME DRIVE MODEL  
BACK BOX MEMORY  
SOFTWARE VERSION  
BUILD  
ZONE LABEL  
ZOOM  
AVAILABLE  
XX.X  
AZIMUTH/ELEVATION  
DIRECTION  
FONT VERSION  
COMM  
XX.X  
ALARM MESSAGE  
DATE/TIME  
2 (SECS)  
ON  
XXXXXXXXXX  
D ADDRESS  
1
2
EVENT LABEL  
2 (SECS)  
P ADDRESS  
CM95OO MODE  
32 PRESETS  
OFF  
OFF  
C
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
PROTOCOL  
DIPSWITCH INFORMATION  
PRESSURIZED*  
<ADDITIONAL>  
X.XX  
LABEL POSITION  
12345678  
1234567890  
SW1[--------] SW2[----------]  
[ZONE LABEL-------]  
[PRESET LABEL-------]  
[ALARM 1-------]  
ADDITIONAL  
SW1 1-8:  
D ADDRESS 1  
FREE MEMORY  
LATEST RESET  
AZIMUTH ZERO OFFSET  
MOTOR ACTIVE  
CAMERA ACTIVE  
VIDEO LEVEL  
XXXXXX  
POWER ON  
0°  
[ALERT MESSAGE---]*  
P ADDRESS 1  
SW2 1 : 32 PRESETS. OFF  
SW2 2 : CM9500 MODE. OFF  
SW2 3 : COAX SPIV  
SW2 4-5 : RS422 <->  
SAVE AND EXIT  
CANCEL AND EXIT  
HELP  
YES  
YES  
NORMAL  
XXXX-XXXX  
ENGLISH X.XX  
XXX/-XX  
SW2 6-8 : COMM. 2400.N.8.1  
SW2 9 : UTC SOURCE. COAX  
SW2 10 : TX/RX TERM.. OFF  
CAMERA MODEL  
LANGUAGE 1  
NE  
XXX.XX  
. . .  
LANGUAGE 10  
ITALIANO X.XX  
PRESS IRIS OPEN TO CONTINUE  
<DIPSWITCH INFORMATION>  
CAMERA  
ADVANCED SETTINGS  
MOTION  
POWER UP  
TYPE OF LIGHTING  
AUTO FOCUS  
T1  
ON  
SUTTER SPEED  
AGC LIMIT  
AUTO  
28  
AUTO FLIP  
ON  
ON  
POWER UP ACTION  
AUTO  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
SURE FOCUS  
OFF  
AUTO IRIS  
AUTO  
66  
0
ZOOM LIMIT  
XXXX  
XXXX  
XXXXXX  
XXXX  
OFF  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
NONE  
25  
AUTO  
ON  
ZOOM SPEED  
8
ON  
26  
ON  
255  
255  
OFF  
HIGH  
OFF  
ON  
SCAN SPEED DEG/S  
PRESET FREEZE FRAME  
LIMIT STOPS  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
<ADVANCED SETTINGS>  
AUTO  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
FIELD ALIGN  
LOW LUX NOISE REDUCTION  
ZONES  
WINDOW BLANKING  
SET WINDOWS  
ZONE NUMBER  
1
STYLE  
GRAY  
OFF  
OFF  
WINDOW NUMBER  
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
<EDIT SCHEDULE>  
ENABLE WINDOW  
REVERSE  
1
***ZONE NOT DEFINED***  
<EDIT ZONE LABEL>  
<EDIT ZONE>  
BLANK ALL ABOVE  
BLANK ALL BELOW  
<SET WINDOWS>  
NO  
ZONE ENABLED  
ZONE BLANKING  
<CLEAR ZONE>  
ON  
OFF  
CLEAR WINDOW  
ALERT*  
REPEAT  
CURRENT READING  
CLEAR  
PASSWORD  
CONSTANT  
TEMPERATURE  
DEWPOINT  
PRESURE  
CLEAR ALL ZONES  
ENABLE PASSWORD  
<EDIT PASSWORD>  
OFF  
ACK ACTION  
ALWAYS ON  
CLEAR ALL PRESETS  
CLEAR ALL PATTERNS  
ACTIVATE AUX  
<CURRENT READING>  
RESET ALERT  
NO  
REFRESH  
CLEAR ALL WINDOW BLANKING  
CLEAR ALL EVENTS  
RESTORE FACTORY DEFAULTS  
*This setting applies only to Pressurized Spectra IV dome systems. Spectra IV systems that are not pressurized will not display this menu item.  
30  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
LINE SYNC  
PRESETS  
EDIT DETECTION AREAS  
PATTERNS  
LINE SYNC  
LINE SYNC PHASE  
ON  
0
PRESET NUMBER  
1
DETECTION AREA 1  
PATTERN NUMBER  
1
***PRESET NOT DEFINED***  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<EDIT SCHEDULE>  
<CLEAR PRESET>  
LOCATION  
SENSITIVITY  
0
<PROGRAM PATTERN>  
<CLEAR PATTERN>  
<EDIT SCHEDULE>  
MEDIUM  
DETECTION AREA 2  
LOCATION  
0
SENSITIVITY  
MEDIUM  
REFERENCE INFO  
PATTERN USAGE  
REMAINING  
0%  
100%  
DETECTION AREA 3  
LOCATION  
<CLEAR CAMERA SETTINGS>  
REFERENCE INFORMATION  
AZIMUTH  
ELEVATION  
ZOOM  
0
SENSITIVITY  
MEDIUM  
DETECTION AREA 4  
LOCATION  
0
SENSITIVITY  
MEDIUM  
ALARMS  
ALARM SETTINGS  
AUX  
TITLE TEXT  
RESUME  
OFF  
5
0
ALARM NUMBER  
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
ALARM CONTACT  
<EDIT SCHEDULE>  
1
LOW  
NONE  
NO  
AUX 1 MODE  
TOGGLE  
ENABLE TITLE TEXT  
<EDIT TITLE TEXT>  
SEQUENCE (SECS)  
RESET DELAY (SECS)  
<ALARM SETTINGS>  
DWELL TIME (SECS)  
AUX 2 MODE  
1
TOGGLE  
1
DWELL TIME (SECS)  
<EDIT SCHEDULE>  
N/O  
EDIT THE PASSWORD  
CLOCK  
EVENT  
EDIT EVENT  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
klmnopqrst  
uvwxyz#&:*  
TIME BASE  
INTERNAL CLOCK  
12 HOUR  
EVENT TYPE  
ALL EVENTS  
EVENT LABEL  
EVENT01  
TIME FORMAT  
SET TIME  
EVENT LABEL  
NEW  
12:00 AM  
EVENT ACTIVE  
EVENT TIME  
EVENT OCCURS  
SUNDAY  
ON  
12:00 AM  
DATE FORMAT  
SET DATE  
DAYLIGHT SAVINGS  
MM/DD/YYYY  
00/00/0000  
OFF  
<EDIT EVENT LABEL>  
<EDIT EVENT>  
<CLEAR EVENT>  
<LIST EVENT>  
ON  
MONDAY  
ON  
TUESDAY  
ON  
HOLIDAY  
WEDNESDAY  
THURSDAY  
FRIDAY  
ON  
<EDIT HOLIDAY>  
<CLEAR HOLIDAY>  
<LIST HOLIDAYS>  
ON  
ON  
ON  
SATURDAY  
HOLIDAY  
SKIP HOLIDAYS  
EVENT TYPE  
PRESET  
C3412M-D (12/08)  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35X LowLight Day/Night Menu Tree  
SPECTRA IV  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
SYSTEM INFORMATION  
DISPLAY SETUP  
SERIAL #  
XXXXXXXXXXXXXX  
XX-XXXX  
PRESET LABEL  
2 (SECS)  
2 (SECS)  
2 (SECS)  
2 (SECS)  
OFF  
DOME DRIVE MODEL  
BACK BOX MEMORY  
SOFTWARE VERSION  
BUILD  
ZONE LABEL  
ZOOM  
AVAILABLE  
XX.X  
AZIMUTH/ELEVATION  
DIRECTION  
FONT VERSION  
COMM  
XX.X  
ALARM MESSAGE  
DATE/TIME  
2 (SECS)  
ON  
XXXXXXXXXX  
D ADDRESS  
1
2
EVENT LABEL  
2 (SECS)  
P ADDRESS  
CM95OO MODE  
32 PRESETS  
OFF  
OFF  
C
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
PROTOCOL  
DIPSWITCH INFORMATION  
PRESSURIZED*  
<ADDITIONAL>  
X.XX  
LABEL POSITION  
12345678  
1234567890  
SW1[--------] SW2[----------]  
[ZONE LABEL-------]  
[PRESET LABEL-------]  
[ALARM 1-------]  
ADDITIONAL  
SW1 1-8:  
D ADDRESS 1  
FREE MEMORY  
LATEST RESET  
AZIMUTH ZERO OFFSET  
MOTOR ACTIVE  
CAMERA ACTIVE  
VIDEO LEVEL  
XXXXXX  
POWER ON  
0°  
[ALERT MESSAGE---]*  
P ADDRESS 1  
SW2 1 : 32 PRESETS. OFF  
SW2 2 : CM9500 MODE. OFF  
SW2 3 : COAX SPIV  
SW2 4-5 : RS422 <->  
SAVE AND EXIT  
CANCEL AND EXIT  
HELP  
YES  
YES  
NORMAL  
XXXX-XXXX  
ENGLISH X.XX  
XXX/-XX  
SW2 6-8 : COMM. 2400.N.8.1  
SW2 9 : UTC SOURCE. COAX  
SW2 10 : TX/RX TERM.. OFF  
CAMERA MODEL  
LANGUAGE 1  
NE  
XXX.XX  
. . .  
LANGUAGE 10  
ITALIANO X.XX  
PRESS IRIS OPEN TO CONTINUE  
<DIPSWITCH INFORMATION>  
CAMERA  
ADVANCED SETTINGS  
MOTION  
POWER UP  
TYPE OF LIGHTING  
AUTO FOCUS  
T1  
ON  
SUTTER SPEED  
AGC LIMIT  
AUTO  
28  
AUTO FLIP  
ON  
ON  
POWER UP ACTION  
AUTO  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
SURE FOCUS  
OFF  
AUTO IRIS  
AUTO  
66  
0
ZOOM LIMIT  
XXXX  
XXXX  
XXXXXX  
XXXX  
OFF  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
NONE  
25  
AUTO  
ON  
ZOOM SPEED  
8
ON  
26  
ON  
255  
255  
OFF  
HIGH  
SCAN SPEED DEG/S  
PRESET FREEZE FRAME  
LIMIT STOPS  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
<ADVANCED SETTINGS>  
AUTO  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
SENSOR SCAN MODE  
FIELD ALIGN  
PROGRESSIVE  
OFF  
E. IMAGE STABILIZER  
IMAGE ENHANCEMENT  
OFF  
DEFAULT  
LOW LUX NOISE REDUCTION  
ON  
WIDE DYNAMIC RANGE  
OFF  
ZONES  
WINDOW BLANKING  
SET WINDOWS  
ZONE NUMBER  
1
STYLE  
GRAY  
OFF  
OFF  
WINDOW NUMBER  
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
<EDIT SCHEDULE>  
ENABLE WINDOW  
REVERSE  
1
***ZONE NOT DEFINED***  
<EDIT ZONE LABEL>  
<EDIT ZONE>  
BLANK ALL ABOVE  
BLANK ALL BELOW  
<SET WINDOWS>  
NO  
ZONE ENABLED  
ZONE BLANKING  
<CLEAR ZONE>  
ON  
OFF  
CLEAR WINDOW  
ALERT*  
REPEAT  
CURRENT READING  
CLEAR  
PASSWORD  
CONSTANT  
TEMPERATURE  
DEWPOINT  
PRESURE  
CLEAR ALL ZONES  
ENABLE PASSWORD  
<EDIT PASSWORD>  
OFF  
ACK ACTION  
ALWAYS ON  
CLEAR ALL PRESETS  
CLEAR ALL PATTERNS  
ACTIVATE AUX  
<CURRENT READING>  
RESET ALERT  
NO  
REFRESH  
CLEAR ALL WINDOW BLANKING  
CLEAR ALL EVENTS  
RESTORE FACTORY DEFAULTS  
*This setting applies only to Pressurized Spectra IV dome systems. Spectra IV systems that are not pressurized will not display this menu item.  
32  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
LINE SYNC  
PRESETS  
EDIT DETECTION AREAS  
PATTERNS  
LINE SYNC  
LINE SYNC PHASE  
ON  
0
PRESET NUMBER  
DETECTION AREA 1  
PATTERN NUMBER  
1
***PRESET NOT DEFINED***  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<MOTION DETECTION>  
<EDIT SCHEDULE>  
LOCATION  
SENSITIVITY  
0
<PROGRAM PATTERN>  
<CLEAR PATTERN>  
<EDIT SCHEDULE>  
MEDIUM  
DETECTION AREA 2  
LOCATION  
0
SENSITIVITY  
MEDIUM  
REFERENCE INFO  
PATTERN USAGE  
REMAINING  
0%  
100%  
DETECTION AREA 3  
LOCATION  
<CLEAR PRESET>  
0
<CLEAR CAMERA SETTINGS>  
REFERENCE INFORMATION  
AZIMUTH  
SENSITIVITY  
MEDIUM  
DETECTION AREA 4  
LOCATION  
0
ELEVATION  
SENSITIVITY  
MEDIUM  
ZOOM  
CUSTOM CAMERA SETTINGS  
ALARMS  
ALARM SETTINGS  
AUX  
TITLE TEXT  
RESUME  
OFF  
5
0
ALARM NUMBER  
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
ALARM CONTACT  
<EDIT SCHEDULE>  
1
LOW  
NONE  
NO  
AUX 1 MODE  
TOGGLE  
ENABLE TITLE TEXT  
<EDIT TITLE TEXT>  
SEQUENCE (SECS)  
RESET DELAY (SECS)  
<ALARM SETTINGS>  
DWELL TIME (SECS)  
AUX 2 MODE  
1
TOGGLE  
1
DWELL TIME (SECS)  
<EDIT SCHEDULE>  
N/O  
EDIT EVENT  
EVENT LABEL  
EVENT01  
EDIT THE PASSWORD  
CLOCK  
EVENT  
EVENT ACTIVE  
EVENT TIME  
EVENT OCCURS  
SUNDAY  
ON  
12:00 AM  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
klmnopqrst  
uvwxyz#&:*  
TIME BASE  
INTERNAL CLOCK  
12 HOUR  
EVENT TYPE  
ALL EVENTS  
TIME FORMAT  
SET TIME  
EVENT LABEL  
NEW  
ON  
12:00 AM  
MONDAY  
ON  
DATE FORMAT  
SET DATE  
MM/DD/YYYY  
00/00/0000  
OFF  
<EDIT EVENT LABEL>  
<EDIT EVENT>  
TUESDAY  
ON  
WEDNESDAY  
THURSDAY  
FRIDAY  
ON  
DAYLIGHT SAVINGS  
<CLEAR EVENT>  
<LIST EVENT>  
ON  
ON  
ON  
SATURDAY  
HOLIDAY  
HOLIDAY  
SKIP HOLIDAYS  
<EDIT HOLIDAY>  
<CLEAR HOLIDAY>  
<LIST HOLIDAYS>  
EVENT TYPE  
PRESET  
C3412M-D (12/08)  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Language  
The language for the on-screen menus is selectable. Available languages include English,  
Spanish, French, German, Italian, Portuguese, Russian, Polish, Turkish, and Czech. The factory  
default language is English.  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
To change the display language:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
1. Use the joystick to position the cursor beside LANGUAGE.  
2. Press Iris Open. The cursor moves to the right, beside the current, selected language.  
EXIT  
3. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
All on-screen menus are changed to the selected language.  
*This setting applies only to Pressurized Spectra IV dome systems.  
34  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
System Information  
The System Information menu displays the dome drive model, software version, available  
SPECTRA IV  
memory, DIP switch information, and other diagnostic information.  
System settings cannot be changed using this menu; this information is for reference only.  
Use the following steps to display the System Information menu:  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
1. Use the joystick to position the cursor beside SYSTEM INFORMATION.  
2. Press Iris Open. The SYSTEM INFORMATION menu opens.  
EXIT  
DIP SWITCH INFORMATION  
SYSTEM INFORMATION  
SERIAL #  
The DIP Switch Information menu displays the dome drive’s current DIP switch settings. This  
provides a way to remotely view the DIP switch settings without removing the dome drive from  
the back box.  
DOME DRIVE MODEL  
BACK BOX MEMORY  
SOFTWARE VERSION  
BUILD  
FONT VERSION  
DIP SWITCH INFORMATION  
COMM  
12345678  
1234567890  
D ADDRESS  
P ADDRESS  
CM9500 MODE  
32 PRESETS  
PROTOCOL  
SW1[- - - - - - - -] SW2[- - - - - - - - - -]  
SW1 1-8 :  
D ADDRESS 1  
P ADDRESS 1  
PRESSURIZED*  
<ADDITIONAL>  
SW2 1 : 32 PRESETS. OFF  
SW2 2 : CM9500 MODE. OFF  
SW2 3 : COAX SPIV  
SW2 4-5 : RS422 <->  
BACK  
EXIT  
SW2 6-8 : COMM. 2400.N.8.1  
SW2 9 : UTC SOURCE. COAX  
SW2 10 : TX/RX TERM.. OFF  
PRESS IRIS OPEN TO CONTINUE  
ADDITIONAL  
FREE MEMORY  
LAST RESET  
AZIMUTH ZERO OFFSET  
MOTOR ACTIVE  
CAMERA ACTIVE  
VIDEO LEVEL  
CAMERA MODEL  
LANGUAGE 1  
LANGUAGE 2  
LANGUAGE 3  
LANGUAGE 4  
LANGUAGE 5  
LANGUAGE 6  
LANGUAGE 7  
LANGUAGE 8  
LANGUAGE 9  
LANGUAGE 10  
<DIPSWITCH INFORMATION>  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Display Setup  
Display setup allows you to program how labels are displayed on the monitor. The following  
labels are available:  
SPECTRA IV  
LANGUAGE  
PRESET LABEL: Identifies preset.  
ZONE LABEL: Identifies zone.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
ZOOM: Identifies the amount of magnification.  
AZIMUTH1/ELEVATION2: Amount of pan from zero degrees vertical and the amount of tilt from  
zero degrees horizontal.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
DIRECTION: Displays compass direction.  
ALARM MESSAGE: Displays activated alarm.  
DATE/TIME: Displays current date and time.  
EVENT LABEL: Displays activated event.  
DISPLAY SETUP  
PRESET LABEL  
ZONE LABEL  
A preset label is displayed when a preset is called. A zone label is displayed when the system  
moves into a zone. The zoom ratio label is displayed when zoom is activated. Azimuth/elevation  
and direction labels are displayed when pan/tilt is activated. An alarm message appears on the  
monitor when an alarm occurs. An event label appears on the monitor when an event occurs.  
ZOOM  
AZIMUTH/ELEVATION  
DIRECTION  
ALARM MESSAGE  
DATE/TIME  
EVENT LABEL  
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
The following settings are available for each label except date and time:  
OFF: Label is not displayed when activated.  
BACK  
EXIT  
CONSTANT: The label is continually displayed when activated.  
2 SECONDS: The label is displayed for 2 seconds after activation.  
5 SECONDS: The label is displayed for 5 seconds after activation.  
10 SECONDS: The label is displayed for 10 seconds after activation.  
The settings for date and time are ON or OFF.  
1 Azimuth is the pan angle from zero to 359 degrees.  
2 Elevation is the tilt position from zero (horizon) to -90 degrees.  
*This setting applies only to Pressurized Spectra IV dome systems.  
36  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
LABEL POSITIONS  
Labels can be placed anywhere on the monitor. This feature allows you to customize the  
appearance of your monitor screen.  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
The following labels are not set at fixed positions:  
PRESET LABEL  
ZONE LABEL  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ALARM 1  
EXIT  
ZOOM RATIO - XXX.XX  
AZIMUTH1/ELEVATION2 - XXX°/-XX°  
DIRECTION - NE  
DISPLAY SETUP  
ALERT MESSAGE3*  
PRESET LABEL  
ZONE LABEL  
TITLE TEXT  
ZOOM  
AZIMUTH/ELEVATION  
DIRECTION  
EVENT LABEL  
ALARM MESSAGE  
DATE/TIME  
To set a label position:  
EVENT LABEL  
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
BACK  
EXIT  
1. Use the joystick to position the cursor beside a label.  
2. Press Iris Open.  
3. Use the joystick to move the label up, down, left, or right.  
4. Press Iris Open.  
LABEL POSITION  
5. Repeat steps 1–4 to position other labels.  
6. Position the cursor next to Save and Exit. Press Iris Open to save settings and exit the menu.  
[ZONE LABEL-------]  
[PRESET LABEL-------]  
[ALARM 1-------]  
[EVENT-------]  
[ALERT MESSAGE-------]*  
<TITLE TEXT>  
SAVE AND EXIT  
CANCEL AND EXIT  
HELP  
XXXo/-XXXo  
NE  
XXX.XX  
XX/XX/YYYY 00:00  
1 Azimuth is the pan angle from zero to 359 degrees.  
2 Elevation is the tilt position from zero (horizon) to -90 degrees.  
3 The alert message is the warning displayed on the monitor if pressure, temperature, or dew point inside the  
dome reach unacceptable levels.  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Dome Settings  
CAMERA  
TYPE OF LIGHTING  
(Does not apply to 16X or 18X models.)  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Pelco has calibrated settings that optimize the white balance and the picture for several lighting  
conditions. There are three settings:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
T1 (default): For use in outdoor applications.  
T2: For use in indoor applications.  
EXIT  
T3: (Available only with 23X models.) For use in applications that use sodium lighting.  
AUTO FOCUS  
DOME SETTINGS  
Auto focus allows the lens to remain in focus during zoom-in, zoom-out, and motion functions.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
There are two auto focus settings:  
ON (default): If auto focus mode is set to ON, the camera will focus automatically when using  
pan, tilt, and zoom (PTZ) functions.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
OFF: Focus is operated manually. To focus, press the Focus Far or Focus Near button on the  
controller.  
Sure Focus  
When sure focus is enabled and all PTZ motions are stopped, the camera will attempt to find a  
fixed focus position and lock to an object in the scene. If a focus lock is acquired or a specific  
amount of time has expired with no focus lock, the focus position remains fixed until PTZ is  
resumed.  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
SURE FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
<ADVANCED SETTINGS>  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
38  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
ZOOM LIMIT  
SPECTRA IV  
LANGUAGE  
Zoom limit allows the user to define a limitation on the amount of telephoto zoom. The settings  
vary depending on camera model.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
16X (Models DD4TC16 and DD4TC16-X)  
The default setting is 32X. Cameras with 128X zoom (16X optical zoom and 8X digital zoom) can  
be set for 16X, 32X, 64X, or 128X.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
18X (Models DD4CBW18 and DD4CBW18-X)  
The default setting is 32X. Cameras with 216X zoom (18X optical zoom and 12X digital zoom) can  
be set for 18X, 32X, 72X, or 144X, 180X, or 216X.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
22X (Models DD4C22, and DD4C22-X)  
The default setting is 32X. Cameras with 264X zoom (22X optical zoom and 12X digital zoom) can  
be set for 22X, 32X, 88X, 176X, 220X, or 264X.  
23X (Models DD4CBW23 and DD4CBW23-X)  
The default setting is 32X. Cameras with 276X zoom (23X optical zoom and 12X digital zoom) can  
be set for 23X, 32X, 92X, 184X, 230X, 276X.  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
35X (Models DD4CBW35 and DD4CBW35-X)  
The default setting is 70X. Cameras with 420X zoom (35X optical zoom and 12X digital zoom) can  
be set for 35X, 70X, 140X, 280X, 350X, or 420X.  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
SURE FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
<ADVANCED SETTINGS>  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ZOOM SPEED  
SPECTRA IV  
LANGUAGE  
Zoom speed allows the user to define how fast the dome will go from full wide zoom to the 16X,  
18X, 22X, 23X, or 35X optical zoom.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Available zoom speed settings for 16X models include:  
HIGH: 1.9 seconds  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
MEDIUM (default): 3.6 seconds  
LOW: 6.0 seconds  
EXIT  
Available zoom speed settings for 18X and 23X models include:  
HIGH: 2.9 seconds  
DOME SETTINGS  
MEDIUM (default): 4.2 seconds  
LOW: 5.8 seconds  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
Available zoom speed settings for 22X models include:  
HIGH: 2.4 seconds  
MEDIUM (default): 3.9 seconds  
LOW: 6.3 seconds  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
Available zoom speed settings for 35X models include:  
HIGH: 3.2 seconds  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
MEDIUM (default): 4.6 seconds  
LOW: 6.6 seconds  
Note: When using the HIGH setting, the image may be out of focus until zooming stops.  
CAMERA  
LOW LIGHT LIMIT  
Low light limit is the maximum duration, in fractions of a second, that the electronic shutter will  
remain open in low light conditions. The default setting is 2.  
TYPE OF LIGHTING  
AUTO FOCUS  
SURE FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
Settings include the following:  
2 = 1/2 second  
4 = 1/4 second  
8 = 1/8 second  
30 = 1/30 second  
60 = 1/60 second  
<ADVANCED SETTINGS>  
15 = 1/15 second  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
40  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
IR CUT FILTER  
(Applies only to 18X, 23X, and 35X models.)  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
The 18X, 23X, and 35X cameras have two modes of operation: color, and black-white. You can  
increase sensitivity in low light conditions by switching to black-white mode (removing the IR cut  
filter). Color mode is preferred in normal lighting conditions.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
The following are the settings for the IR cut filter:  
EXIT  
OFF: Manual operation is controlled by preset 88 (filter IN) and 89 (filter OUT).  
AUTO (default): Automatic operation is controlled by the auto IR level setting.  
IN: Images are always displayed in color mode.  
DOME SETTINGS  
OUT: Images are always displayed in black-white mode.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
Note: The IN and OUT settings are only available when editing camera settings through the  
Presets menu (refer to Presets on page 57).  
Low Light Focus  
If you are using an IR illuminator, the low light focus feature of the camera can be tuned to  
correspond to the setting of the illuminator.  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
There are three low light focus settings:  
OFF (default): Low light focus is not activated.  
850NM: Low light focus is tuned to 850 nm (nanometers).  
950NM: Low light focus is tuned to 950 nm.  
BACK  
EXIT  
CAMERA  
Auto IR Level  
TYPE OF LIGHTING  
AUTO FOCUS  
The auto IR level is the light level at which the infrared filter switches IN or OUT.  
SURE FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
Following are the available settings for the auto IR level:  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
DUSK (default): Approximately 6 lux (black-white); approximately 13 lux (color).  
DARK: Approximately 0.1 lux (black-white); approximately 2 lux (color).  
<ADVANCED SETTINGS>  
Notes:  
BACK  
EXIT  
If backlight compensation is ON and the IR cut filter switches OUT in normal lighting  
conditions, adjust the Auto IR Level to a darker setting. Refer to Backlight Compensation (BLC)  
Low light does not mean no light. Some type of illumination is required (street light, IR light,  
etc.). The camera is not sensitive to IR light when the IR cut filter is IN.  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
ADVANCED CAMERA SETTINGS  
SHUTTER SPEED  
SPECTRA IV  
LANGUAGE  
Shutter speed is the duration of the electronic shutter. Program shutter speed to operate  
automatically (Auto) or manually (Numeric Value).  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
AUTO (default): The electronic shutter speed is set automatically by the amount of light sensed  
by the camera.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
NUMERIC VALUE: Spectra IV/Spectra IV SE dome systems have several numerical shutter  
speed settings. The higher the number, the faster the electronic shutter.  
EXIT  
The slowest shutter speed setting is 2 = 1/2 second.  
The fastest setting is 30,000 = 1/30,000 second.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
Increasing the shutter speed lowers the light sensitivity and reduces the streaking of fast moving  
objects.  
Set the shutter speed to 100 if you are using an NTSC camera in a 50 Hz environment. This will  
eliminate any flicker that may occur in the picture.  
<TITLE TEXT>  
<ALERT>*  
AGC LIMIT  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
AGC limit allows users to adjust how the system balances AGC (automatic gain control) and  
electronic shutter in low light conditions. As scene lighting decreases, the system will  
automatically adjust, adding a mixture of AGC and slow shutter according to the AGC limit  
setting. AGC limit can be set between 0 and 40, with 40 applying maximum AGC before slow  
shutter. In contrast, setting AGC limit to 0 will force the system software to apply maximum slow  
shutter (as defined by the low light limit setting) before any AGC is applied. The default AGC  
settings vary depending on camera model.  
BACK  
EXIT  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
SURE FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
Note: The maximum slow shutter that the system will achieve is 1/2 second shutter (refer to  
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AGC LIMIT  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
SENSOR SCAN MODE  
FIELD ALIGN  
E. IMAGE STABILIZER  
IMAGE ENHANCEMENT  
LOW LUX NOISE REDUCTION  
WIDE DYNAMIC RANGE  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
42  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
AUTO IRIS  
SPECTRA IV  
LANGUAGE  
Auto iris is the lens function that automatically opens and closes the iris in response to changing  
light conditions.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Program the auto iris to operate automatically or at a user-defined level.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
OFF: Auto iris is disabled, and control is always manual.  
AUTO (default): The iris is adjusted automatically to produce a constant video output as  
determined by the auto iris level setting.  
EXIT  
If auto iris is in the auto mode, it will remain that way until the iris is manually opened or closed.  
The dome will return to auto mode when it is panned or tilted more than 15 degrees.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
Auto Iris Level  
Auto iris level is the numeric value the auto iris uses to maintain the brightness level of the  
camera. Increase the value to brighten the scene. Decrease the value to darken the scene.  
This setting can be adjusted if the video level in the auto iris mode is too bright or too dark.  
<TITLE TEXT>  
<ALERT>*  
Note: If backlight compensation is ON, decrease the auto iris level setting.  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
Auto Iris Peak  
Increasing the peak value will cause the auto iris circuit to react more to highlights or “peaks” in  
the picture. Decreasing this value will cause it to use the average video level to adjust the iris.  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
SURE FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AGC LIMIT  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
SENSOR SCAN MODE  
FIELD ALIGN  
E. IMAGE STABILIZER  
IMAGE ENHANCEMENT  
LOW LUX NOISE REDUCTION  
WIDE DYNAMIC RANGE  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
AUTO SHARPNESS  
Auto sharpness enhances picture detail by increasing the aperture gain of the camera and  
sharpening the edges in the picture.  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
There are two settings:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ON (default): The camera automatically maintains a normal sharpness mode.  
OFF: The sharpness of the picture is set manually by programming the sharpness level.  
Sharpness level settings range from 0–63.  
EXIT  
DOME SETTINGS  
AUTO WHITE BALANCE  
This feature automatically processes the viewed image to retain color balance over a color  
temperature range. The default setting for auto white balance is ON.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
R GAIN: Adjusts the picture output in the red range. As you change the value, you will see the  
color change on your monitor.  
B GAIN: Adjusts the picture output in the blue range. As you change the value, you will see the  
color change on your monitor.  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
SURE FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AGC LIMIT  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
SENSOR SCAN MODE  
FIELD ALIGN  
E. IMAGE STABILIZER  
IMAGE ENHANCEMENT  
LOW LUX NOISE REDUCTION  
WIDE DYNAMIC RANGE  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
44  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
BACKLIGHT COMPENSATION (BLC)  
SPECTRA IV  
LANGUAGE  
If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette.  
Backlight compensation enhances objects in the center of the picture. The dome uses the center  
of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash  
out to white. The camera will adjust the iris so that the object in the sensitive area is properly  
exposed.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
There are two backlight compensation settings:  
OFF (default): Backlight compensation is not activated.  
ON: Backlight compensation is activated.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
If backlight compensation is ON, decrease the auto iris level setting and adjust the auto IR level  
VIDEO LEVEL  
Set the video output to one of the following options:  
NORMAL: 1.0 Vp-p.  
HIGH (default setting): 1.2 Vp-p. to compensate for losses in video cable.  
BACK  
EXIT  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
SURE FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AGC LIMIT  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
SENSOR SCAN MODE  
FIELD ALIGN  
E. IMAGE STABILIZER  
IMAGE ENHANCEMENT  
LOW LUX NOISE REDUCTION  
WIDE DYNAMIC RANGE  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
SENSOR SCAN MODE  
(Applies only to 35X models.)  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Sensor scan mode controls the internal processing of the camera's image sensor. The data  
scanned from the image sensor at each field time is used for the internal image control  
algorithms and digital signal processing (DSP).  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
Note: When changing from PROGRESSIVE to INTERLACED, or vice-versa, the camera restarts to  
establish the new setting.  
EXIT  
There are two sensor scan modes:  
DOME SETTINGS  
PROGRESSIVE (default): Produces a higher quality image by using each line scanned from the  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
image sensor.  
INTERLACED: Produces a slight increase in sensitivity by using blended data from pairs of lines  
scanned from the image sensor.  
When sensor scan mode is set to INTERLACED, the wide dynamic range and image enhancement  
features are automatically disabled. There may be additional effects, such as a degradation of  
the signal-to-noise ratio, degradation of the color reproduction, and a loss of motion detection for  
presets configured with motion detection.  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
FIELD ALIGN  
(Applies only to 18X, 23X, and 35X models.)  
<EVENT>  
BACK  
EXIT  
Field align determines whether the camera produces progressive segmented frame output (PsF)  
or interlaced frame output. Analog video from the camera is always output in separate fields as  
required for compatibility. This feature allows PsF to be recombined by an encoding device  
without a time difference between fields, as is typically seen from interlaced analog video  
output. Enabling field align requires that the encoding device you are using always combines the  
odd and even fields in the specified order.  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
SURE FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
There are three field alignment settings:  
<ADVANCED SETTINGS>  
BACK  
EXIT  
OFF (default): Field alignment is disabled. Use this setting if you are using an analog device/  
system or a digital encoder that does not support PsF.  
ODD: Arranges the odd field for a particular video frame before the even field for that frame.  
EVEN: Arranges the even field for a particular video frame before the odd field for that frame.  
Notes:  
ADVANCED SETTINGS  
SHUTTER SPEED  
AGC LIMIT  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
If you enable field alignment by selecting ODD or EVEN, you must disable any deinterlacing  
settings for the encoding device to achieve maximum resolution.  
B GAIN  
The ODD and EVEN settings require that the sensor scan mode is set to PROGRESSIVE. If field  
align is set to ODD or EVEN, the sensor scan mode automatically changes to PROGRESSIVE.  
BACKLIGHT COMP  
VIDEO LEVEL  
SENSOR SCAN MODE  
FIELD ALIGN  
E. IMAGE STABILIZER  
IMAGE ENHANCEMENT  
LOW LUX NOISE REDUCTION  
WIDE DYNAMIC RANGE  
BACK  
EXIT  
46  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
ELECTRONIC IMAGE STABILIZATION  
SPECTRA IV  
LANGUAGE  
(Applies only to 35X models.)  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Electronic image stabilization is a feature of the camera that can compensate for some forms of  
external influences. In all cases, care should be taken to make sure that any dome system is  
mounted to a rigid location.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
In the event that vibration is introduced to the dome system, a user can select one of the  
electronic image stabilization settings in the menu. The available settings are OFF, 5 Hz, and  
10 Hz. Users should apply each of the settings to the camera to see which one best addresses  
the vibration that is affecting the video quality.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
Electronic image stabilization will not correct for all ranges of vibration. If either of the settings  
fails to eliminate the vibration seen in the video, other measures should be taken to isolate the  
vibration or to seek a more rigid mounting location.  
Notes:  
<TITLE TEXT>  
<ALERT>*  
When electronic image stabilization is applied, digital slow shutter and wide dynamic range  
are disabled. Zoom, image resolution, and viewing angle are also limited when this feature  
is activated.  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
Electronic image stabilization cannot be used while in a preset that has motion detection  
activated.  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
SURE FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AGC LIMIT  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
SENSOR SCAN MODE  
FIELD ALIGN  
E. IMAGE STABILIZER  
IMAGE ENHANCEMENT  
LOW LUX NOISE REDUCTION  
WIDE DYNAMIC RANGE  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
IMAGE ENHANCEMENT  
(Applies only to 35X models.)  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
The image enhancement feature improves the definition of objects, lines, or text in high contrast  
areas, making them appear sharper.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
There are two image enhancement settings:  
DEFAULT: Image enhancement is not activated.  
ENHANCED: Image enhancement is activated.  
EXIT  
DOME SETTINGS  
Warning: When using this feature be aware that picture noise, although unnoticeable to  
the eye, will increase and may cause compression rate changes in DVRs, NVRs, and  
network devices.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
LOW LUX NOISE REDUCTION  
(Applies only to 18X and 23X models.)  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
Low lux noise reduction helps to reduce video noise in low light scenes. When enabled, low lux  
noise reduction is directly affected by the AGC settings for the dome system.  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
The following are the low lux noise reduction settings:  
ON (default): Low lux noise reduction is enabled. As the scene darkens and AGC increases, the  
noise reduction effect automatically increases. As noise reduction increases, you may also notice  
some afterimaging and a slight reduction in color saturation.  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
SURE FOCUS  
ZOOM LIMIT  
OFF: Low lux noise reduction is disabled.  
ZOOM SPEED  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AGC LIMIT  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
SENSOR SCAN MODE  
FIELD ALIGN  
E. IMAGE STABILIZER  
IMAGE ENHANCEMENT  
LOW LUX NOISE REDUCTION  
WIDE DYNAMIC RANGE  
BACK  
EXIT  
48  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
WIDE DYNAMIC RANGE  
(Applies only to 23X and 35X models.)  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Wide dynamic range (WDR) balances the brightest and darkest sections of a scene to produce a  
picture that is better balanced in lighting and provides more detail.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
Available settings are OFF and ON; the default setting is OFF. When wide dynamic range is set to  
ON the frame rate is reduced from the standard 30–15 frames per second (fps). Also, when this  
setting is ON the iris will not close completely, even in manual mode.  
EXIT  
Note: Wide dynamic range is disabled when electronic image stabilization is set to 5 Hz or 10 Hz.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
Wide Dynamic Range ON  
Wide Dynamic Range OFF  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
SURE FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
LOW LIGHT LIMIT  
IR CUT FILTER  
LOW LIGHT FOCUS  
AUTO IR LEVEL  
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AGC LIMIT  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
SENSOR SCAN MODE  
FIELD ALIGN  
E. IMAGE STABILIZER  
IMAGE ENHANCEMENT  
LOW LUX NOISE REDUCTION  
WIDE DYNAMIC RANGE  
BACK  
EXIT  
C3412M-D (12/08)  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
MOTION SETTINGS  
AUTO FLIP  
SPECTRA IV  
LANGUAGE  
When the camera tilts downward and goes just beyond the vertical position, the dome rotates  
180 degrees. When the dome rotates (flips), the camera starts moving upward as long as you  
continue to hold the joystick in the down position. Once you let go of the joystick after the dome  
rotates, joystick control returns to normal operation. The auto-flip feature is useful for following a  
person who passes directly beneath the dome.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
There are two auto flip modes:  
EXIT  
ON (default): Auto flip mode is enabled.  
OFF: Auto flip mode is disabled.  
DOME SETTINGS  
PROPORTIONAL PAN  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the  
amount of zoom. At telephoto zoom settings, the pan and tilt speeds will be slower for a given  
amount of joystick deflection than at wide zoom settings. This keeps the image from moving too  
fast on the monitor when there is a large amount of zoom.  
There are three proportional pan modes:  
ON (default): Enables the proportional pan mode.  
OFF: Disables proportional pan mode. The pan speed will not depend on the amount of zoom.  
2X: Increases the speed of the proportional pan mode to twice that used when proportional pan  
is set to ON.  
BACK  
EXIT  
MOTION  
AUTO FLIP  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
SCAN SPEED (DEG/S)  
PRESET FREEZE FRAME  
LIMIT STOPS  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
*This setting applies only to Pressurized Spectra IV dome systems.  
50  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
PARK TIME  
SPECTRA IV  
LANGUAGE  
This feature allows the dome to begin a specified operation (scan, preset, or pattern) after a  
programmed time of inactivity.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Park time can be programmed from 1–720 minutes (12 hours), or set to zero, which disables this  
feature. The default setting is zero.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
Park Action  
This feature will define the activity when the dome parks. The following settings are available:  
NONE (default): No action.  
DOME SETTINGS  
AUTO SCAN: Dome starts auto scan operation.  
RANDOM SCAN: Dome starts random scan operation.  
FRAME SCAN: Dome starts frame scan operation.  
PRESET 1: Dome goes to preset 1.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
PRESET 8: Dome goes to preset 8.  
PATTERN 1: Dome runs pattern 1.  
<TITLE TEXT>  
<ALERT>*  
PATTERN 2: Dome runs pattern 2.  
<CLEAR>  
PATTERN 3: Dome runs pattern 3.  
<PASSWORD>  
<CLOCK>  
<EVENT>  
PATTERN 4: Dome runs pattern 4.  
BACK  
EXIT  
PATTERN 5: Dome runs pattern 5.  
PATTERN 6: Dome runs pattern 6.  
PATTERN 7: Dome runs pattern 7.  
PATTERN 8: Dome runs pattern 8.  
MOTION  
(Only 22X, 23X, and 35X models allow PATTERN 2 through PATTERN 8.)  
AUTO FLIP  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
SCAN SPEED (DEG/S)  
PRESET FREEZE FRAME  
LIMIT STOPS  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
SCAN SPEED  
SPECTRA IV  
LANGUAGE  
Scan speed is the degrees per second that the dome will pan when in a scan mode. Scan speed is  
adjustable from 1 to 40 degrees per second through the programming menu. The default setting  
is 25 degrees per second.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
PRESET FREEZE FRAME  
EXIT  
This feature freezes the scene on the monitor when going to a preset. This allows for smooth  
transition from one preset scene to another. Preset freeze frame also reduces bandwidth when  
used with digital network systems such as PelcoNetand guarantees that blanked areas will not  
be revealed when going to a preset.  
DOME SETTINGS  
There are three preset freeze frame settings:  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
ON: The image on the screen freezes when a preset is called. When the dome reaches the  
preset, the image is unfrozen and the preset scene is displayed.  
OFF: The image is never frozen.  
AUTO (default): Freeze frame is turned on automatically if window blanking is ON. If window  
blanking is OFF, freeze frame is off.  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
MOTION  
AUTO FLIP  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
SCAN SPEED (DEG/S)  
PRESET FREEZE FRAME  
LIMIT STOPS  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
*This setting applies only to Pressurized Spectra IV dome systems.  
52  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
LIMIT STOPS  
SPECTRA IV  
LANGUAGE  
Limit stops are programmable stops that limit the pan range of the dome. There must be two  
limits, a left and a right, to define an area.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
There are two types of limit stops:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
MANUAL: A manual (joystick) pan operation stops when a limit stop is reached.  
SCAN: The dome reverses direction during random, frame, or auto scanning when a limit stop  
is reached.  
EXIT  
To set manual or scan stops:  
1. Use the joystick to position the cursor beside SET MANUAL STOPS or SET SCAN STOPS.  
2. Press Iris Open.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
3. Follow the directions displayed on the monitor.  
Note: In order for the manual or scan stops to work, the LIMIT STOPS option must be ON.  
To clear manual or scan stops:  
<TITLE TEXT>  
<ALERT>*  
1. Use the joystick to position the cursor beside CLEAR MANUAL STOPS or CLEAR SCAN  
STOPS.  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
2. Press Iris Open.  
3. Follow the directions displayed on the monitor.  
MOTION  
AUTO FLIP  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
SCAN SPEED (DEG/S)  
PRESET FREEZE FRAME  
LIMIT STOPS  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
AZIMUTH ZERO  
SPECTRA IV  
LANGUAGE  
Azimuth is the pan angle from zero to 359 degrees. Azimuth zero is the pan position you specify to  
be the zero degree point. Azimuth zero is normally set to magnetic north. Once set, azimuth and  
compass readings are based on the set Azimuth Zero point.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
To program azimuth zero:  
1. Use the joystick to position the cursor beside SET AZIMUTH ZERO.  
2. Press Iris Open.  
EXIT  
3. Follow the directions displayed on the monitor.  
To clear azimuth zero:  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
1. Use the joystick to position the cursor beside CLEAR AZIMUTH ZERO.  
2. Press Iris Open.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
3. Follow the directions displayed on the monitor.  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
MOTION  
AUTO FLIP  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
SCAN SPEED (DEG/S)  
PRESET FREEZE FRAME  
LIMIT STOPS  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
*This setting applies only to Pressurized Spectra IV dome systems.  
54  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
POWER UP  
POWER UP ACTION  
SPECTRA IV  
LANGUAGE  
This setting defines a specific activity (scan, preset, pattern) to be performed in the event the  
power to the dome is cycled.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
The following settings are available:  
NONE: No action.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
AUTO (default): The dome resumes its prior activity or direction before the power outage.  
AUTO SCAN: Dome starts auto scan operation.  
RANDOM SCAN: Dome starts random scan operation.  
FRAME SCAN: Dome starts frame scan operation.  
PRESET 1: Dome goes to preset 1.  
EXIT  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
PRESET 2: Dome goes to preset 2.  
PRESET 3: Dome goes to preset 3.  
PRESET 4: Dome goes to preset 4.  
PRESET 5: Dome goes to preset 5.  
PRESET 6: Dome goes to preset 6.  
PRESET 7: Dome goes to preset 7.  
PRESET 8: Dome goes to preset 8.  
PATTERN 1: Dome runs pattern 1.  
BACK  
EXIT  
PATTERN 2: Dome runs pattern 2.  
PATTERN 3: Dome runs pattern 3.  
PATTERN 4: Dome runs pattern 4.  
PATTERN 5: Dome runs pattern 5.  
POWER UP  
PATTERN 6: Dome runs pattern 6.  
POWER UP ACTION  
PATTERN 7: Dome runs pattern 7.  
BACK  
EXIT  
PATTERN 8: Dome runs pattern 8.  
(Only 22X, 23X, and 35X models allow PATTERN 2 through PATTERN 8.)  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
LINE SYNC  
Line sync refers to a programmable function that allows you to synchronize all cameras within a  
matrix system.  
SPECTRA IV  
LANGUAGE  
Spectra IV and Spectra IV SE dome systems automatically sense V-Sync input. No line sync setup  
is required for Pelco control systems that provide a V-Sync signal.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
For matrix systems that do not output V-Sync, there are two settings for line synchronization:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ON (default): Adjusts the phase of the line sync to synchronize input power. Line sync phase  
settings range from zero to 359 degrees.  
EXIT  
OFF: The dome synchronizes to the internal clock.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
LINE SYNC  
LINE SYNC  
LINE SYNC PHASE  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
56  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PRESETS  
The model of the back box you are using limits the number of programmable presets that can be stored and retrieved in the  
back box memory. If you are using an older model back box, you may program and use up to the maximum number of  
presets available to the dome drive. However, if the dome drive is changed, the back box model will limit the number of  
stored presets available to the new dome drive. Refer to the table below for more information.  
Back Box Series  
Model  
Number of Stored Presets  
Spectra  
99  
Spectra SE  
Spectra III  
Spectra IV  
BB53  
BB4  
15  
128  
256  
The Spectra IV dome system, which includes 16X and 18X models, has 128 preset positions. The programmable presets  
are numbered 1–32, 35–82, and 100–150.  
The Spectra IV SE dome system, which includes 22X, 23X, and 35X models, has 256 preset positions. The programmable  
presets are numbered 1–32, 35–82, and 100–256.  
Note: The number of available presets may be limited by the head-ins, controllers, and DVRs that are connected to your  
dome system.  
Each of the user-definable presets can be programmed to use pan, tilt, camera settings, and motion detection.  
The following presets are predefined for specific functions:  
Preset  
33:  
Action  
Flip command. Pans the dome drive 180 degrees.  
34:  
Pan zero command. Directs the dome drive to the factory-determined zero reference point.  
83–87:  
88:  
89:  
90–91:  
92–93:  
94:  
Reserved.  
IR filter IN (color).  
IR filter OUT (black-white).  
Manual limit stops.  
Scan limit stops.  
Reserved.  
95:  
96:  
Select main programming menu.  
Stop a scan.  
97:  
98:  
Random scanning.  
Frame scanning.  
99:  
Start auto scanning  
C3412M-D (12/08)  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Note: For American Dynamics controllers with only 32 presets, switch SW2-1 on the dome drive  
SPECTRA IV  
to the ON position. When SW2-1 is ON, preset  
LANGUAGE  
99 becomes 32  
98 becomes 31  
97 becomes 30  
96 becomes 29  
95 becomes 28  
93 becomes 26  
92 becomes 25  
91 becomes 24  
90 becomes 23  
89 becomes 22  
88 becomes 21  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
If the limit stops are turned off, presets 23–26 can be used as regular presets.  
Use the following steps to program a preset.  
DOME SETTINGS  
1. Select the preset number:  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
a. Use the joystick to position the cursor beside PRESET NUMBER. Press Iris Open.  
The cursor moves to the right.  
b. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
2. Edit the preset label:  
<TITLE TEXT>  
<ALERT>*  
a. Use the joystick to position the cursor beside EDIT PRESET LABEL.  
b. Press Iris Open. The following appears on the monitor:  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
LABEL FOR PRESET  
PRESET NUMBER ------  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
OK  
CANCEL  
SPACE  
BACKSPACE  
PRESETS  
klmnopqrst  
uvwxyz*;:  
PRESET NUMBER  
1
* * * PRESET NOT DEFINED * * *  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<MOTION DETECTION>  
c. Use the joystick to position the cursor beside a character. Press Iris Open to enter  
selection. To clear a character, position the cursor beside BACKSPACE, and then press  
Iris Open.  
<EDIT SCHEDULE>  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
BACK  
EXIT  
d. When label is completed, move the cursor to OK. Press Iris Open to return to the  
Preset menu.  
REFERENCE INFORMATION  
AZIMUTH  
-
-
-
-
ELEVATION  
ZOOM RATIO  
3. Edit the preset scene:  
CUSTOM CAMERA SETTINGS  
a. Use the joystick to position the cursor beside EDIT PRESET SCENE.  
b. Press Iris Open.  
c. Follow the directions displayed on the monitor.  
*This setting applies only to Pressurized Spectra IV dome systems.  
58  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Edit preset camera settings:  
SPECTRA IV  
LANGUAGE  
a. Use the joystick to position the cursor beside EDIT CAMERA SETTINGS.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
b. Press Iris Open. The EDIT CAMERA SETTINGS window appears on the monitor. Refer  
camera settings.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
c. To edit the camera settings schedule, use the joystick to position the cursor beside  
EDIT SCHEDULE. Press Iris Open.  
EXIT  
The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on  
page 80) with the following exceptions. In the Edit Schedule menu, the event type  
cannot be changed. Also, the Holiday feature cannot be accessed from the Edit  
Schedule menu.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
For instructions on changing the features in the Edit Schedule menu, refer to Edit  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
Notes:  
For 23X and 35X models, there are two additional options available for the IR cut filter that are  
only available when programming a preset. The additional settings are IN and OUT. If the IR cut  
filter is set to IN, the preset scene will be in color. If the IR cut filter is set to OUT, the preset  
scene will be in black-white.  
BACK  
EXIT  
You can copy camera settings from one preset to another preset. To copy camera settings do  
the following:  
(1) Use the joystick to position the cursor beside COPY CAMERA SETTINGS.  
(2) Press Iris Open. The cursor moves to the right.  
PRESETS  
(3) Move the joystick up or down to view selections. Press Iris Open to enter selection.  
PRESET NUMBER  
1
* * * PRESET NOT DEFINED * * *  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<MOTION DETECTION>  
<EDIT SCHEDULE>  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
BACK  
EXIT  
REFERENCE INFORMATION  
AZIMUTH  
-
-
-
-
ELEVATION  
ZOOM RATIO  
CUSTOM CAMERA SETTINGS  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ENABLE MOTION DETECTION  
(Applies only to 23X and 35X models.)  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
The following are the settings for motion detection:  
OFF (default): Motion detection is turned off (disabled).  
ON: Motion detection is turned on (enabled).  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
Note: Motion detection does not work if the shutter speed is set at less than 1/60 of a second.  
EXIT  
EDIT DETECTION AREAS  
(Applies only to 23X and 35X models.)  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
Four motion detection areas can be defined for a preset. Use the following steps to edit motion  
detection areas.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
1. Edit detection areas 1, 2, 3, or 4:  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
a. Use the joystick to position the cursor beside EDIT DETECTION AREAS.  
<PASSWORD>  
<CLOCK>  
b. Press Iris Open. The EDIT DETECTION AREAS programming window appears on the  
monitor.  
<EVENT>  
BACK  
EXIT  
c. Use the joystick to position the cursor beside LOCATION for DETECTION AREA 1, 2, 3,  
or 4.  
PRESETS  
d. Press Iris Open. The cursor moves to the right next to the number 0.  
PRESET NUMBER  
* * * PRESET NOT DEFINED * * *  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<MOTION DETECTION>  
e. Move the joystick up. A blue rectangle appears in the upper left-hand corner of the  
screen.  
<EDIT SCHEDULE>  
f. Use the joystick to place the blue rectangle over the desired detection area.  
g. Press Iris Open to make a selection.  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
BACK  
EXIT  
REFERENCE INFORMATION  
AZIMUTH  
2. Set the sensitivity of the motion detection area:  
ELEVATION  
ZOOM RATIO  
CUSTOM CAMERA SETTINGS  
a. Position the cursor next to SENSITIVITY for DETECTION AREA 1, 2, 3, or 4.  
b. Press Iris Open, the cursor moves to the right.  
MOTION DETECTION  
MOTION DETECTION ENABLED  
<EDIT DETECTION AREAS>  
ACTIVATE AUX  
c. Use the joystick to select one of the following sensitivity levels:  
HIGH: The sensitivity level is high.  
MEDIUM (default): Average sensitivity.  
LOW: The sensitivity level is low.  
AUX TIME (SECS)  
BACK  
EXIT  
d. Press Iris Open to make selection.  
*This setting applies only to Pressurized Spectra IV dome systems.  
60  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
EDIT DETECTION AREAS  
DETECTION AREA 1  
LOCATION  
0
SENSITIVITY  
MEDIUM  
DETECTION AREA 2  
LOCATION  
SENSITIVITY  
0
MEDIUM  
DETECTION AREA 3  
LOCATION  
SENSITIVITY  
0
MEDIUM  
DETECTION AREA 4  
LOCATION  
0
SENSITIVITY  
MEDIUM  
BACK  
EXIT  
MOTION DETECTION AREAS  
Note: Motion detection is not guaranteed to catch 100 percent of activity.  
C3412M-D (12/08)  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ACTIVATE AUX COMMAND  
(Applies only to 23X and 35X models.)  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Motion detection can be programmed to trigger an auxiliary command when motion is detected.  
The following are the settings for ACTIVATE AUX:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
OFF (default): Motion detection will not trigger an AUX command.  
1: Triggers a command to AUX 1.  
EXIT  
2: Triggers a command to AUX 2.  
DOME SETTINGS  
AUX TIME  
(Applies only to 23X and 35X models.)  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
Aux time is the length of time the auxiliary will remain on after motion is detected. Available  
settings for AUX TIME are 1–60 seconds.  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
EDIT SCHEDULE  
The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 80) with  
the following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also,  
the Holiday feature cannot be accessed from the Edit Schedule menu.  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on  
PRESETS  
PRESET NUMBER  
* * * PRESET NOT DEFINED * * *  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<MOTION DETECTION>  
<EDIT SCHEDULE>  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
BACK  
EXIT  
REFERENCE INFORMATION  
AZIMUTH  
ELEVATION  
ZOOM RATIO  
CUSTOM CAMERA SETTINGS  
MOTION DETECTION  
MOTION DETECTION ENABLED  
<EDIT DETECTION AREAS>  
ACTIVATE AUX  
AUX TIME (SECS)  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
62  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
PATTERNS  
A pattern is a memorized, repeating series of pan, tilt, zoom, and preset functions that can be  
recalled with a command from a controller or automatically by a programmed function (alarm,  
park, event, or power-up).  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Both 16X and 18X models have one user-defined pattern available. The 22X, 23X, and 35X models  
can handle up to eight patterns. Pattern length is based upon memory usage rather than a fixed  
amount of time. The complexity of a pattern will determine the amount of storage available to  
program other patterns.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
Note: In most cases, the memory available will allow for ample time to schedule typical  
patterns. If the scheduled patterns are unusually lengthy or complex, there is a possibility that  
there may not be enough remaining memory to program all eight patterns for the 22X, 23X, and  
35X models.  
DOME SETTINGS  
To program a pattern:  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
1. Use the joystick to position the cursor beside PATTERN NUMBER. Press Iris Open.  
The cursor moves to the right.  
2. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
3. Use the joystick to position the cursor beside PROGRAM PATTERN.  
4. Press Iris Open. The Patterns programming window appears on the monitor.  
5. Follow the directions displayed on the monitor.  
After a pattern is programmed, the remaining storage percentage is displayed on the screen.  
This is the amount of memory available to program the remaining patterns.  
BACK  
EXIT  
To clear a pattern:  
1. Use the joystick to position the cursor beside CLEAR PATTERN.  
2. Press Iris Open.  
PATTERNS  
PATTERN NUMBER  
<PROGRAM PATTERN>  
<CLEAR PATTERN>  
<EDIT SCHEDULE>  
3. Follow the directions displayed on the monitor.  
To edit the pattern schedule:  
BACK  
EXIT  
The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 80) with  
the following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also,  
the Holiday feature cannot be accessed from the Edit Schedule menu.  
REFERENCE INFORMATION  
PATTERN USAGE  
REMAINING  
For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on  
Note: When programming one or more presets within a pattern, use the normal controller  
commands to call a preset. Not all controllers can start all patterns. However, any of the patterns  
can be automatically started with park, power-up, event, and alarm functions.  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ZONES  
A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. The  
Spectra IV and Spectra IV SE dome systems are capable of eight zones, each with a 20-character  
label.  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
To program a zone:  
1. Use the joystick to position the cursor beside ZONE NUMBER. Press Iris Open, and the  
cursor moves to the right.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
2. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
3. Use the joystick to position the cursor beside EDIT ZONE.  
EXIT  
4. Press Iris Open. The Zone programming window appears on the monitor.  
5. Follow the directions displayed on the monitor. After the left and right limit stops are set,  
the Zones menu reappears with the ZONE ENABLED option set to YES.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
To edit a zone label:  
1. Use the joystick to position the cursor beside EDIT ZONE LABEL.  
2. Press Iris Open. The following information appears on the monitor:  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
LABEL FOR ZONE  
ZONE NUMBER ------  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
OK  
CANCEL  
SPACE  
BACKSPACE  
klmnopqrst  
uvwxyz*;:  
BACK  
EXIT  
3. Use the joystick to position the cursor beside a character. Press Iris Open to enter selection.  
To clear a character, position the cursor beside BACKSPACE, and then press Iris Open.  
ZONES  
ZONE NUMBER  
* * * ZONE NOT DEFINED * * *  
4. When the label is completed, move the cursor to OK. Press Iris Open to return to the Zones  
menu.  
<EDIT ZONE LABEL>  
<EDIT ZONE>  
ZONE ENABLED  
ZONE BLANKING  
To disable a zone (a zone is enabled automatically when it is programmed) or to blank a zone:  
1. Move the cursor beside ZONE ENABLED or ZONE BLANKING.  
2. Press Iris Open. The cursor moves to the right.  
<CLEAR ZONE>  
BACK  
EXIT  
3. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
To clear a zone:  
1. Use the joystick to position the cursor beside CLEAR ZONE.  
2. Press Iris Open. Follow the instructions on the screen.  
*This setting applies only to Pressurized Spectra IV dome systems.  
64  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
WINDOW BLANKING  
Window blanking allows a user to program four-sided areas that cannot be viewed by the  
operator of the dome system. A blanked area will move with pan and tilt functions and  
automatically adjust in size as the lens zooms telephoto and wide.  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
The 16X and 18X models have one user-defined window blank available. The 22X, 23X, and 35X  
models have eight available user-defined window blanks.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
Spectra IV and Spectra IV SE dome systems have two styles of window blanking: Gray and Smear.  
If the style is set to Gray, the blanked area is covered with a solid gray window. If Smear is  
selected images behind the window will be noticeable but not distinguishable.  
EXIT  
To set a window blanking area:  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
1. Use the joystick to position the cursor beside WINDOW BLANKING. Press Iris Open.  
The WINDOW BLANKING menu appears on the screen.  
2. Move the joystick to position the cursor beside SET WINDOWS. Press Iris Open to enter.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
3. Position the cursor beside WINDOW NUMBER. Press Iris Open. The cursor moves to the  
right.  
4. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
5. Use the joystick to position the cursor beside EDIT WINDOW LOCATION. Press Iris Open,  
and then follow the instructions that appear on the screen. When all four corners are set,  
the SET WINDOWS menu reappears, the blanked area is displayed, and the ENABLE  
WINDOW option is set to YES.  
WINDOW BLANKING  
STYLE  
Notes:  
Use the inside corner of the window selection tool as a guide  
when selecting the upper left, upper right, bottom right, and  
bottom left corners of the window.  
BLANK ALL ABOVE  
BLANK ALL BELOW  
<SET WINDOWS>  
INSIDE CORNER  
Set windows are not visible when editing a new window  
location.  
BACK  
EXIT  
SET WINDOWS  
WINDOW NUMBER  
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
<EDIT SCHEDULE>  
ENABLE WINDOW  
REVERSE  
CLEAR WINDOW  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
6. The blanked area can be programmed to turn on or off at a specified zoom point. To set the  
zoom point:  
SPECTRA IV  
LANGUAGE  
a. Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then press  
Iris Open.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
b. Zoom in to the point where you want window blanking to turn on. Press Iris Open to  
set the zoom point.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
Notes:  
EXIT  
Since the area is already blanked out, it may be difficult to determine when you want  
window blanking to turn on. Reverse the window before setting the zoom point. When  
finished reverse the window again to blank out the area.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
Increase the size of the window if any part of the blanked area is revealed during PTZ  
operations.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
WINDOW BLANKING  
STYLE  
Window Blanking Disabled  
Window Blanking Enabled  
BLANK ALL ABOVE  
BLANK ALL BELOW  
EDIT SCHEDULE  
<SET WINDOWS>  
The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 80) with the  
following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also, the  
Holiday feature cannot be accessed from the Edit Schedule menu.  
BACK  
EXIT  
For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on  
SET WINDOWS  
REVERSE  
WINDOW NUMBER  
A blanked out area can be reversed to make it visible and the areas on both sides of it not visible.  
The areas above and below the blanking area remain visible. Reversing the window a second  
time will return it to its original condition.  
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
<EDIT SCHEDULE>  
ENABLE WINDOW  
REVERSE  
CLEAR WINDOW  
CLEAR WINDOW  
All areas that have been set for window blanking are cleared.  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
66  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
BLANK ALL ABOVE/BLANK ALL BELOW  
The Blank All Above and Blank All Below options add additional flexibility to setting up privacy areas. These settings are  
ideal for applications where a complete pan location needs to be blanked.  
Table C. Window Blank Settings  
Blank All Above  
Tilt Angle Blanked Area  
Blank All Below  
Tilt Angle Blanked Area  
OFF  
0
No blanking  
OFF  
0
No blanking  
Horizon to 3° above horizon  
Horizon to 92° below horizon  
10° to 92° below horizon  
20° to 92° below horizon  
30° to 92° below horizon  
40° to 92° below horizon  
50° to 92° below horizon  
60° to 92° below horizon  
70° to 92° below horizon  
80° to 92° below horizon  
-10  
-20  
-30  
-40  
-50  
-60  
-70  
-80  
3° above horizon to 10° below horizon  
3° above horizon to 20° below horizon  
3° above horizon to 30° below horizon  
3° above horizon to 40° below horizon  
3° above horizon to 50° below horizon  
3° above horizon to 60° below horizon  
3° above horizon to 70° below horizon  
3° above horizon to 80° below horizon  
-10  
-20  
-30  
-40  
-50  
-60  
-70  
-80  
HORIZON  
CAMERA  
Figure 3. Window Blank Tilt Angles  
C3412M-D (12/08)  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ALARMS  
SPECTRA IV  
LANGUAGE  
The Spectra IV SE dome systems have seven alarm inputs that can be programmed as high,  
medium, or low priority. When an alarm is received, an input signal to the dome triggers the user-  
defined action (go to preset, run pattern, etc.) programmed for the alarm.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Note: Refer to the notation in step 6 for the limited alarm features available for 16X and 18X  
models.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
There are three global alarm settings:  
EXIT  
RESUME: This mode lets the dome resume its previous activity (scan, pattern, or previous  
position) after all alarms are cleared.  
DOME SETTINGS  
SEQUENCE: This is the time the dome will perform an alarm activity when more than one alarm  
of the same priority occurs at the same time.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
RESET DELAY: This is the amount of time the dome considers the alarm to be active after it has  
physically cleared.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
Use the following steps to program alarm settings.  
1. Use the joystick to position the cursor beside ALARM SETTINGS. Press Iris Open.  
2. Select the alarm number:  
a. Use the joystick to position the cursor beside ALARM NUMBER.  
b. Press Iris Open. The cursor moves to the right.  
c. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
ALARMS  
RESUME  
SEQUENCE (SECS)  
RESET DELAY (SECS)  
<ALARM SETTINGS>  
BACK  
EXIT  
ALARM SETTINGS  
ALARM NUMBER  
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
ALARM CONTACT  
<EDIT SCHEDULE>  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
68  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Select the alarm priority:  
SPECTRA IV  
LANGUAGE  
a. Use the joystick to position the cursor beside ALARM PRIORITY.  
b. Press Iris Open. The cursor moves to the right.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
c. Move the joystick up or down to view the available selections. Available settings  
include HIGH, MEDIUM, and LOW (default). If multiple alarms with different priorities  
are active at the same time, the dome will only go to the alarms with the highest  
priority.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
d. Press Iris Open to enter selection.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
HIGH: Alarm action takes highest priority and will override manual PTZ control.  
MEDIUM/LOW: Alarm action will not occur if an alarm occurs during manual pan,  
tilt, and zoom control.  
4. Set the alarm action:  
a. Use the joystick to position the cursor beside ALARM ACTION.  
b. Press Iris Open. The cursor moves to the right.  
c. Move the joystick up or down to view the available selections. The following are the  
settings for alarm action:  
BACK  
EXIT  
NONE: No action when alarm is triggered.  
PRESET: Dome goes to the preset that is the same as the alarm number. Preset 1 will  
go to Alarm 1.  
ALARMS  
RESUME  
SEQUENCE (SECS)  
RESET DELAY (SECS)  
PATTERN 1: Dome runs pattern 1 when alarm is triggered.  
PATTERN 2: Dome runs pattern 2 when alarm is triggered.  
PATTERN 3: Dome runs pattern 3 when alarm is triggered.  
PATTERN 4: Dome runs pattern 4 when alarm is triggered.  
PATTERN 5: Dome runs pattern 5 when alarm is triggered.  
PATTERN 6: Dome runs pattern 6 when alarm is triggered.  
PATTERN 7: Dome runs pattern 7 when alarm is triggered.  
PATTERN 8: Dome runs pattern 8 when alarm is triggered.  
AUTO SCAN: Dome starts auto scan operation when alarm is triggered.  
RANDOM SCAN: Dome starts random scan operation when alarm is triggered.  
FRAME SCAN: Dome starts frame scan operation when alarm is triggered.  
<ALARM SETTINGS>  
BACK  
EXIT  
ALARM SETTINGS  
ALARM NUMBER  
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
ALARM CONTACT  
<EDIT SCHEDULE>  
d. Press Iris Open to enter selection.  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Set the auxiliary to activate:  
SPECTRA IV  
LANGUAGE  
a. Use the joystick to position the cursor beside ACTIVATE AUX.  
b. Press Iris Open. The cursor moves to the right.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
c. Move the joystick up or down to view the following available selections.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
NO (default): Not activated.  
EXIT  
1: An alarm action will close AUX 1.  
2: An alarm action will close AUX 2.  
DOME SETTINGS  
d. Press Iris Open to enter selection.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
Note: The AUX 1/AUX2 will stop when all the alarms assigned to it have cleared. If the  
AUX1/AUX is set up as momentary, then it will be activated each time a new alarm is  
activated.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
6. Set the alarm contact:  
<TITLE TEXT>  
<ALERT>*  
a. Use the joystick to position the cursor beside ALARM CONTACT.  
b. Press Iris Open. The cursor moves to the right.  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
c. Move the joystick up or down to view the following available selections.  
N/O (default): Normally open.  
N/C: Normally closed.  
ALARMS  
RESUME  
SEQUENCE (SECS)  
RESET DELAY (SECS)  
d. Press Iris Open to enter selection.  
Note: The alarm contact feature is functional and available for 16X and 18X models only if  
the dome drive is installed in a Spectra III SE or Spectra IV SE back box.  
<ALARM SETTINGS>  
BACK  
EXIT  
7. To edit the alarm schedule:  
The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 80)  
with the following exceptions. In the Edit Schedule menu, the event type cannot be  
changed. Also, the Holiday feature cannot be accessed from the Edit Schedule menu.  
ALARM SETTINGS  
ALARM NUMBER  
For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on  
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
ALARM CONTACT  
<EDIT SCHEDULE>  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
70  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AUX  
Note: If a 16X or 18X model dome drive is installed in a Spectra III SE or Spectra IV SE back box,  
the auxiliary feature is functional and available. If a 16X or 18X model is installed in a standard  
Spectra III or Spectra IV back box, the auxiliary feature is not available.  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
An auxiliary output is a programmable signal from the dome back box that can trigger another  
device to operate. An auxiliary output is programmable to trigger from an alarm or from a controller.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
An AUX 1 command from the controller will activate the relay in the dome and operate the device  
that is connected to the relay. The output of AUX 1 can be connected to the alarm input of a  
system switch to activate automatic monitor switching and recording.  
EXIT  
An AUX 2 command from the controller will place a ground at the output of AUX 2 to operate the  
device that is connected to it.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
The following are the available AUX mode settings:  
TOGGLE (default): Changes the state of the auxiliary output every time an AUX command  
is received from the controller.  
LATCHING: Must receive an AUX ON/AUX OFF command from the controller to turn the  
auxiliary output on/off.  
MOMENTARY: An AUX ON command from the controller turns the auxiliary output on for the  
programmed DWELL TIME. The auxiliary output will automatically turn off when the dwell time  
is finished.  
EDIT SCHEDULE  
BACK  
EXIT  
The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 80) with  
the following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also,  
the Holiday feature cannot be accessed from the Edit Schedule menu.  
AUX  
For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on  
AUX 1 MODE  
TOGGLE  
DWELL TIME (SECS)  
AUX 2 MODE  
DWELL TIME (SECS)  
<EDIT SCHEDULE>  
1
TOGGLE  
1
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
TITLE TEXT  
Title text is the label used to identify the camera viewed on the monitor. Up to 20 characters can  
be used for a title.  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
To edit the title text label, do the following:  
1. Use the joystick to position the cursor beside EDIT TITLE TEXT.  
2. Press Iris Open. The following appears on the monitor:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
EDIT TITLE TEXT  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXY.,-/  
OK  
CANCEL  
SPACE  
BACKSPACE  
abcdefghij  
DOME SETTINGS  
klmnopqrst  
uvwxyz#&:*  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
3. Use the joystick to position the cursor beside a character. Press Iris Open to select the  
character. To clear a character, position the cursor beside BACKSPACE, and then press Iris  
Open.  
4. When the title is completed, move the cursor to OK. Press Iris Open to return to the Title  
Text menu.  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
5. Enable the title text label by doing the following:  
a. Move the cursor beside ENABLE TITLE TEXT.  
b. Press Iris Open. The cursor moves to the right.  
<EVENT>  
BACK  
EXIT  
c. Move the joystick up or down to view the selections. Select ON and then press Iris  
Open to enable the title text.  
TITLE TEXT  
ENABLE TITLE TEXT  
<EDIT TITLE TEXT>  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
72  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ALERT  
Note: The Alert option applies only to Pressurized Spectra IV dome systems. Spectra IV systems  
SPECTRA IV  
that are not pressurized will not display this menu item.  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT  
Sensors strategically placed inside the pressurized dome system continually monitor pressure,  
temperature, and dew point. If internal conditions reach unacceptable levels, an alert message  
appears on the screen describing the alert condition. For example, if pressure drops below 1 psig,  
LOW PRESSURE is displayed on the monitor.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
The following system conditions will trigger an alert message:  
EXIT  
System Condition  
Alert Message  
Temperature is above 140°F (60°C)  
Temperature is below -40°F (-40°C)  
Pressure is above 13 PSIG  
Pressure is below 1 PSIG  
HIGH TEMPERATURE  
LOW TEMPERATURE  
HIGH PRESSURE  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
LOW PRESSURE  
The difference between the temperature and  
the dew point is less than or equal to 3°C.  
DEW POINT (HIGH HUMIDITY)  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
The alert message will be repeatedly displayed until the system controller acknowledges the  
alert condition by selecting ACK ALERT in the main menu. Once acknowledged, the alert message  
changes to the programmed acknowledge action (ACK ACTION). If the alert condition remains  
active after a period of time, the alert message reappears on the monitor, restarting the alert  
message cycle. This cycle will continue to repeat until the alert condition is resolved.  
BACK  
EXIT  
REPEAT  
This setting programs how often an alert message is repeatedly displayed until the system  
controller acknowledges the alert condition. The following are the settings:  
CONSTANT: The alert message is continuously displayed on the monitor until acknowledged.  
ALERT  
REPEAT  
15 MIN: The alert message is displayed every 15 minutes for a 15-second duration until  
acknowledged.  
ACK ACTION  
ACTIVATE AUX  
<CURRENT READING>  
RESET ALERT  
30 MIN: The alert message is displayed every 30 minutes for a 15-second duration until  
acknowledged.  
BACK  
EXIT  
60 MIN: The alert message is displayed every 60 minutes for a 15-second duration until  
acknowledged.  
OFF: The alert message is disabled and will not be displayed on the monitor.  
C3412M-D (12/08)  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
ACK ACTION  
SPECTRA IV  
LANGUAGE  
Set ACK ACTION to program the frequency at which an alert message is displayed after the alert  
condition has been acknowledged. The following settings are available:  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT  
ALWAYS ON: The alert message is displayed until alert conditions are cleared.  
OFF 8 HRS: The alert message is turned off for 8 hours. Message returns after 8 hours if the  
alert condition persists.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
OFF 24 HRS: The alert message is turned off for 24 hours. Message returns after 24 hours if  
EXIT  
the alert condition persists.  
OFF 48 HRS: The alert message is turned off for 48 hours. Message returns after 48 hours if the  
alert condition persists.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
ACTIVATE AUX  
This setting activates an auxiliary when an alert condition exists. Settings include the following  
options:  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>  
<CLEAR>  
NONE (default): Not activated.  
1: An alert condition will close AUX 1.  
2: An alert condition will close AUX 2.  
<PASSWORD>  
<CLOCK>  
CURRENT READING  
The Current Reading menu displays the existing status of temperature, pressure, and dew point  
inside the dome system. An arrow displayed to the left of a menu item denotes that an alert  
condition exists.  
<EVENT>  
BACK  
EXIT  
ALERT  
An up arrow indicates the reading is over the threshold. A down arrow indicates the reading is  
below the threshold.  
REPEAT  
ACK ACTION  
ACTIVATE AUX  
<CURRENT READING>  
RESET ALERT  
The high temperature alert occurs if the temperature is above 140°F (60°C).  
The low temperature alert occurs if the temperature is below -40°F (-40°C).  
The high pressure alert occurs if the pressure is above 13 PSIG.  
The low pressure alert occurs if the pressure is below 1 PSIG.  
BACK  
EXIT  
The dew point (high humidity) alert occurs if the difference between the temperature and the dew  
point is less than or equal to 3°C.  
Note: The normal operating temperature inside the unit will be greater than the temperature  
outside the back box due to the heat emitted by the system’s electronics.  
CURRENT READING  
TEMPERATURE  
DEWPOINT  
PRESSURE  
REFRESH  
RESET ALERT  
Reset alert clears the alert condition and removes the alert label from the monitor. The system  
automatically checks internal conditions 60 seconds after reset. If conditions are still unacceptable,  
the alert label reappears on the screen indicating further corrective action is required.  
BACK  
EXIT  
74  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
CLEAR  
Use this setting to clear user-defined settings or return the dome to factory default settings.  
The following are the available settings:  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
ALL ZONES: Clears all zones. To clear a single zone, refer to Zones on page 64.  
ALL PRESETS: Clears all presets. To clear a single preset, refer to Presets on page 57.  
ALL PATTERNS: Clears all patterns. To clear a single pattern, refer to Patterns on page 63.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ALL WINDOW BLANKING: Clears all blanked windows. To clear a single blanked window,  
EXIT  
CLEAR ALL EVENTS: Clears all events. To clear a single event, refer to Event on page 80.  
RESTORE FACTORY DEFAULTS: Restores all camera settings to factory default settings.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
CLEAR  
CLEAR ALL ZONES  
CLEAR ALL PRESETS  
CLEAR ALL PATTERNS  
CLEAR ALL WINDOW BLANKING  
CLEAR ALL EVENTS  
RESTORE FACTORY DEFAULTS  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PASSWORD  
Spectra IV and Spectra IV SE feature password protection to prevent unauthorized changes to the  
dome settings. An operator can open the System Information and Display Setup menus, but  
cannot access any of the dome settings menus.  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Controller/keyboard commands cannot override password-protected settings. If a keyboard is  
used to set a preset, pattern, or zone, the Enter Password menu appears on the monitor.  
The password must be entered before programming can continue.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
At least one character must be entered to create a valid password.  
EXIT  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
PASSWORD  
ENABLE PASSWORD  
<EDIT PASSWORD>  
BACK  
EXIT  
EDIT THE PASSWORD  
----------  
1234567890  
OK  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
CANCEL  
SPACE  
BACKSPACE  
abcdefghij  
klmnopqrst  
uvwxyz*;:  
*This setting applies only to Pressurized Spectra IV dome systems.  
76  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
CLOCK  
The clock is used to program the current date and time. The date and time set in the Clock menu  
is used to program events. The date and time can also be displayed on the monitor when the  
menus are not being accessed.  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
To program the clock, do the following:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
1. Use the joystick to position the cursor beside TIME BASE. Press Iris Open. The following are  
the settings for time base:  
EXIT  
POWER LINE: This is the most accurate time base and is the preferred selection in areas  
with a stable power line frequency.  
INTERNAL CLOCK: The internal clock should be used in areas where the power line  
frequency is not accurate.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
a. Move the joystick up or down to view the selections.  
b. Press Iris Open to select INTERNAL CLOCK or POWER LINE.  
2. Use the joystick to position the cursor beside TIME FORMAT. Press Iris Open. Move the  
joystick up or down to view the selections. Select 12 HOUR or 24 HOUR, and then press Iris  
Open to confirm the time format.  
3. Use the joystick to position the cursor beside SET TIME. Press Iris Open. Scroll through the  
hours until the desired time appears. Use the joystick to move the cursor to the right. Scroll  
through the minutes until the desired time appears. Press Iris Open to select the time.  
BACK  
EXIT  
4. Use the joystick to position the cursor beside DATE FORMAT. Press Iris Open. Move the  
joystick up or down to select MM/DD/YYYY or DD/MM/YYYY. Press Iris Open to confirm  
the date format.  
CLOCK  
5. Use the joystick to position the cursor beside SET DATE. Press Iris Open. Scroll through the  
TIME BASE  
TIME FORMAT  
SET TIME  
days, months, and years until the desired number appears. Press Iris Open to select the  
date.  
DATE FORMAT  
SET DATE  
6. Use the joystick to position the cursor beside DAYLIGHT SAVINGS. Press Iris Open.  
The following are the settings for daylight savings:  
DAYLIGHT SAVINGS  
BACK  
EXIT  
OFF: Daylight saving time will be turned off.  
FIXED DATE: Daylight saving time occurs on the same date each year.  
RELATIVE DATE: Daylight saving time occurs on a different date each year, such as the  
first Sunday in April.  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. If FIXED DATE was selected, the following appears on the monitor:  
CLOCK  
TIME BASE  
TIME FORMAT  
SET TIME  
INTERNAL CLOCK  
12 HOUR  
00:00 AM  
DATE FORMAT  
SET DATE  
MM/DD/YYYY  
00/00/0000  
DAYLIGHT SAVINGS  
TIME SHIFT  
START DATE  
MONTH  
FIXED DATE  
1 HOUR  
APRIL  
1
02:00 AM  
DAY  
START TIME  
END DATE  
MONTH  
DAY  
OCTOBER  
1
02:00 AM  
END TIME  
BACK  
EXIT  
a. Use the joystick to position the cursor beside TIME SHIFT. Press Iris Open. Scroll through the options until the  
desired selection appears. Press Iris Open to select the time shift.  
b. Use the joystick to position the cursor beside the start date MONTH. Press Iris Open. Scroll through the options  
until the desired month appears. Press Iris Open to select the month.  
c. Use the joystick to position the cursor beside the start date DAY. Press Iris Open. Scroll through the options until  
the desired date appears. Press Iris Open to select the day.  
d. Use the joystick to position the cursor beside START TIME. Press Iris Open. Scroll through the hours until the  
desired time appears. Use the joystick to move the cursor to the right. Scroll through the minutes until the  
desired time appears. Press Iris Open to select the start time.  
e. Repeat steps b–d for the ending date and time.  
78  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. If RELATIVE DATE was selected, the following appears on the monitor:  
CLOCK  
TIME BASE  
TIME FORMAT  
SET TIME  
INTERNAL CLOCK  
12 HOUR  
00:00 AM  
DATE FORMAT  
SET DATE  
MM/DD/YYYY  
00/00/0000  
DAYLIGHT SAVINGS RELATIVE DATE  
TIME SHIFT  
START DATE  
MONTH  
1 HOUR  
APRIL  
1ST  
SUNDAY  
02:00 AM  
WEEK  
DAY  
START TIME  
END DATE  
MONTH  
WEEK  
OCTOBER  
LAST  
SUNDAY  
02:00 AM  
DAY  
END TIME  
BACK  
EXIT  
Follow the instructions in step 7 for FIXED DATE, adding WEEK.  
C3412M-D (12/08)  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EVENT  
An event is a preprogrammed camera, park, scan, preset, pattern, window blanking, alarm, or  
auxiliary function that can be performed automatically at a specific date and time.  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
For example, suppose a camera is set to run in a continuous pattern that scans a parking lot  
during business hours Monday through Friday. On Saturday and Sunday the camera needs to stop  
running the pattern and observe a gate. First, program a preset to set the camera to observe the  
gate. Second, schedule an event to activate the preset on the weekends. Finally, a second,  
separate event must be scheduled to end the first event and allow the camera to return to the  
pattern on Monday.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
Note: Events do not have a selectable duration. A second event must be scheduled to end a  
previous event.  
DOME SETTINGS  
Events can be programmed from the Preset, Pattern, Window Blanking, Alarm, or Aux menus, or  
they can be programmed from the Event menu. Events are managed individually or as a group  
from the Event menu.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
*This setting applies only to Pressurized Spectra IV dome systems.  
80  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
EVENT TYPE  
SPECTRA IV  
LANGUAGE  
Any of the available event types can be selected from this menu, or you may select ALL EVENTS  
to manage the events as a group.The following are the settings for event type:  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
SCAN: A scan event executes a specified scan (random, auto, or frame scan) using the limit  
stops and scan speed defined in the Motion menu. Refer to Motion Settings on page 50.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
PARK: A park event executes the user-defined park action as specified in the Motion menu.  
EXIT  
WINDOW BLANKING: A window blanking event activates or deactivates a previously defined  
window blank. The window blank remains activated or deactivated until another programmed  
event changes the state of the window or you modify it through the Window Blanking menu.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
AUX: An auxiliary event turns on/off an auxiliary output when the event triggers. Refer to Aux on  
ALARM: An alarm event executes the action associated with the specified alarm number. Refer  
PATTERN: A pattern event starts a previously defined pattern when the event is triggered. Refer  
<TITLE TEXT>  
<ALERT>*  
CAMERA: A camera event assigns the camera settings of a preset to the current camera  
settings located in the Camera menu. Refer to Camera on page 38. The preset that is referenced  
by the event must be defined prior to setting up a camera event.  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
For the camera event to function, the referenced preset must have Custom Camera Settings  
activated. Refer to Presets on page 57.  
Note: If you have camera settings defined in the Camera menu that you wish to restore  
following a camera event which overwrites those settings, you must save the original settings as  
a separate preset prior to the camera event being triggered. You can then set a second camera  
event to call the preset that has the original settings saved. Camera settings can also be changed  
manually from the Camera menu following the original camera event.  
EVENT  
EVENT TYPE  
EVENT LABEL  
<EDIT EVENT LABEL>  
<EDIT EVENT>  
<CLEAR EVENT>  
<LIST EVENT>  
PRESET: A preset event executes a previously defined preset when the event is triggered. Refer  
HOLIDAY  
Note: The event type cannot be changed if you are accessing it through the Edit Schedule option  
from the Preset, Pattern, Window Blanking, Alarm, or Aux menu.  
<EDIT HOLIDAY>  
<CLEAR HOLIDAY>  
<LIST HOLIDAYS>  
BACK  
EXIT  
REFERENCE INFORMATION  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
EVENT LABEL  
Set the event label to NEW to create a new event.  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Use the following steps to manage an existing event.  
1. Use the joystick to position the cursor beside EVENT LABEL. Press Iris Open.  
2. Move the joystick up or down to scroll through the events. Press Iris Open to enter selection.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
As you scroll through the events, the reference information at the bottom of the screen  
displays the corresponding details for each event. To view a list of all events and their  
details, refer to List Event on page 84.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
EVENT LABEL  
After an event is programmed, the label can be changed using the following steps:  
1. Use the joystick to position the cursor beside EDIT EVENT LABEL.  
2. Press Iris Open. The following appears on the monitor:  
EDIT EVENT LABEL  
EVENT 1  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXY.,-/  
abcdefghij  
OK  
CANCEL  
BACK  
EXIT  
SPACE  
BACKSPACE  
klmnopqrst  
uvwxyz#&:*  
EVENT  
3. Use the joystick to position the cursor beside a character. Press Iris Open to enter the  
selection. To clear a character, position the cursor beside BACKSPACE, and then press Iris  
Open.  
EVENT TYPE  
EVENT LABEL  
<EDIT EVENT LABEL>  
<EDIT EVENT>  
<CLEAR EVENT>  
<LIST EVENT>  
4. When the label is completed, move the cursor to OK. Press Iris Open to return to the Edit  
Schedule menu.  
HOLIDAY  
After an event is labeled, the label will be displayed when the event is activated according to the  
display setup values for this label. Refer to Display Setup on page 36 for instructions on how to  
change the way a label is displayed on the monitor.  
<EDIT HOLIDAY>  
<CLEAR HOLIDAY>  
<LIST HOLIDAYS>  
BACK  
EXIT  
REFERENCE INFORMATION  
*This setting applies only to Pressurized Spectra IV dome systems.  
82  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
EDIT EVENT  
Use the following steps to edit an event.  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
1. Use the joystick to position the cursor beside EDIT EVENT.  
2. Press Iris Open. The following appears on the monitor:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EDIT EVENT  
EXIT  
EVENT LABEL  
EVENT 1  
EVENT ACTIVE  
EVENT TIME  
EVENT OCCURS  
SUNDAY  
NO  
12:00 AM  
OFF  
DOME SETTINGS  
MONDAY  
OFF  
TUESDAY  
OFF  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
WEDNESDAY  
THURSDAY  
FRIDAY  
OFF  
OFF  
OFF  
SATURDAY  
HOLIDAY  
OFF  
SKIP HOLIDAYS  
EVENT TYPE  
NUMBER  
PRESET  
1
BACK  
EXIT  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
a. Use the joystick to position the cursor beside EVENT ACTIVE. Press Iris Open. Scroll  
to select NO to leave the event inactive or YES to activate the event. Press Iris Open to  
confirm your selection.  
<EVENT>  
BACK  
EXIT  
b. Use the joystick to position the cursor beside EVENT TIME. Press Iris Open. Scroll  
through the hours until the desired time appears. Use the joystick to move the cursor  
to the right. Scroll through the minutes until the desired time appears. Press Iris Open  
to select the time.  
EVENT  
EVENT TYPE  
EVENT LABEL  
c. Use the joystick to position the cursor beside SUNDAY. Press Iris Open. The available  
options are OFF and ON. Press Iris Open to confirm your selection.  
<EDIT EVENT LABEL>  
<EDIT EVENT>  
<CLEAR EVENT>  
<LIST EVENT>  
d. Follow the instructions in the previous step for the remaining days of the week.  
HOLIDAY  
<EDIT HOLIDAY>  
<CLEAR HOLIDAY>  
<LIST HOLIDAYS>  
e. Use the joystick to position the cursor beside HOLIDAY. Press Iris Open. The following  
are the holiday settings:  
BACK  
EXIT  
SKIP HOLIDAYS: The event will not occur on a day of the week for which it is set if  
that date is in the list of holidays.  
REFERENCE INFORMATION  
ON: The event will activate on holidays that are set in the Event menu, in addition to  
its normally scheduled days of the week.  
OFF: The event only occurs on the days of the week that it is scheduled; holidays have  
no effect on the event.  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
CLEAR EVENT  
To clear an event:  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
1. Use the joystick to position the cursor beside CLEAR EVENT.  
2. Press Iris Open.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
3. Follow the directions displayed on the monitor.  
EXIT  
LIST EVENT  
To list events:  
DOME SETTINGS  
1. Use the joystick to position the cursor beside LIST EVENT.  
2. Press Iris Open.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
3. All programmed events will be listed.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
HOLIDAY  
Use the following steps to create a new holiday.  
<PASSWORD>  
<CLOCK>  
<EVENT>  
1. Use the joystick to position the cursor beside HOLIDAY. Press Iris Open.  
BACK  
EXIT  
2. Move the joystick up or down to scroll through the options. If no holidays were created in  
the past, NEW is the only selectable option. Press Iris Open to select NEW.  
3. Proceed to Edit Holiday on page 85.  
EVENT  
Use the following steps to manage an existing holiday.  
1. Use the joystick to position the cursor beside HOLIDAY. Press Iris Open.  
EVENT TYPE  
EVENT LABEL  
<EDIT EVENT LABEL>  
<EDIT EVENT>  
<CLEAR EVENT>  
<LIST EVENT>  
2. Move the joystick up or down to scroll through the holidays. Press Iris Open to enter a  
selection.  
HOLIDAY  
3. Proceed to Edit Holiday on page 85.  
<EDIT HOLIDAY>  
<CLEAR HOLIDAY>  
<LIST HOLIDAYS>  
Note: Holidays cannot be changed through the Edit Schedule option from the Preset, Pattern,  
Window Blanking, Alarm, or Aux menus.  
BACK  
EXIT  
REFERENCE INFORMATION  
*This setting applies only to Pressurized Spectra IV dome systems.  
84  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
EDIT HOLIDAY  
Use the following steps to edit a holiday:  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
1. Use the joystick to position the cursor beside EDIT EVENT LABEL.  
2. Press Iris Open.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
3. Use the joystick to position the cursor beside OCCURRENCE. Press Iris Open. The following  
are the settings for Occurrence:  
EXIT  
FIXED DATE: The holiday occurs on the same date each year.  
RELATIVE DATE: The holiday occurs on a different date each year, such as the third  
Sunday in April.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
4. If FIXED DATE was selected as the occurrence, the following appears on the monitor:  
EDIT HOLIDAY  
OCCURRENCE  
MONTH  
DAY  
FIXED DATE  
JANUARY  
1
BACK  
EXIT  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
a. Use the joystick to position the cursor beside MONTH. Press Iris Open. Scroll through  
the options until the desired month appears. Press Iris Open to select the month.  
<EVENT>  
BACK  
EXIT  
b. Use the joystick to position the cursor beside DAY. Press Iris Open. Scroll through the  
options until the desired date appears. Press Iris Open to select the day.  
5. If RELATIVE DATE was selected as the occurrence, the following appears on the monitor:  
EVENT  
EVENT TYPE  
a. Use the joystick to position the cursor beside MONTH. Press Iris Open. Scroll through  
the options until the desired month appears. Press Iris Open to select the month.  
EVENT LABEL  
<EDIT EVENT LABEL>  
<EDIT EVENT>  
<CLEAR EVENT>  
<LIST EVENT>  
b. Use the joystick to position the cursor beside WEEK. Press Iris Open. Scroll through  
the options until the desired week appears. Press Iris Open to select the week.  
HOLIDAY  
<EDIT HOLIDAY>  
<CLEAR HOLIDAY>  
<LIST HOLIDAYS>  
c. Use the joystick to position the cursor beside DAY. Press Iris Open. Scroll through the  
options until the desired day of the week appears. Press Iris Open to select the day.  
BACK  
EXIT  
REFERENCE INFORMATION  
*This setting applies only to Pressurized Spectra IV dome systems.  
C3412M-D (12/08)  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
CLEAR HOLIDAY  
To clear a holiday:  
SPECTRA IV  
LANGUAGE  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
1. Use the joystick to position the cursor beside CLEAR HOLIDAY.  
2. Press Iris Open.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
3. Follow the directions displayed on the monitor.  
EXIT  
LIST HOLIDAYS  
To list events:  
DOME SETTINGS  
1. Use the joystick to position the cursor beside LIST HOLIDAYS.  
2. Press Iris Open.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
3. All programmed holidays will be listed.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
<CLOCK>  
<EVENT>  
BACK  
EXIT  
EVENT  
EVENT TYPE  
EVENT LABEL  
<EDIT EVENT LABEL>  
<EDIT EVENT>  
<CLEAR EVENT>  
<LIST EVENT>  
HOLIDAY  
<EDIT HOLIDAY>  
<CLEAR HOLIDAY>  
<LIST HOLIDAYS>  
BACK  
EXIT  
REFERENCE INFORMATION  
*This setting applies only to Pressurized Spectra IV dome systems.  
86  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
SCHEDULED EVENTS  
Use this page to record scheduled events.  
EVENT NUMBER  
Example:  
EVENT TYPE  
LABEL  
TIME  
OCCURS  
HOLIDAY  
1
Preset  
Weekend  
11:00 AM  
Sat–Sun  
Skips Holidays  
Description: Camera focuses on gate on weekends when the office is closed.  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
_______________________________________________________________________________________  
C3412M-D (12/08)  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Reset, Cycle Power, Reboot  
RESET CAMERA  
Use this function to reset all camera settings to factory default parameters.  
SPECTRA IV  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
CYCLE CAMERA POWER  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
If the camera is not operating or if you lose camera control, cycle camera power. Cycling camera  
power resets the camera but does not change any saved camera settings.  
EXIT  
REBOOT SYSTEM  
Reboot the system if it is not operating or if there is no control. Rebooting the system will cycle  
dome and camera power without changing programmed dome settings.  
88  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Software/Language File Upload  
The RJ-45 data port of the dome drive allows access for on-site setup, testing, and uploading of revised operating  
software and language files. A Pelco field service tool is required to perform these operations. Field service tools include  
Pelco’s remote monitor kit (IPS-RMK), remote data port box (IPS-RDPE-2), and remote monitor cable (IPS-CABLE).  
For instructions on how to upload revised operating software and language files refer to the Installation/Operation manual  
supplied with the field service tool.  
Note: Only perform software uploads when necessary. Software uploads do not need to be performed if the dome system  
is operating properly.  
During a software/language file upload, a progress bar will appear on the monitor to indicate data is being transferred to  
the Spectra dome system. The default setting for data transmission is 115.2 KB per second. Noisy and long-run  
connections will slow the transmission rate.  
C3412M-D (12/08)  
89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Suggested Preventative Maintenance  
The Spectra IV and Spectra IV SE dome systems do not require any special maintenance.  
Occasionally, dust may build up on the inside or the outside of the dome. If this occurs, turn power off to the unit and  
remove the lower dome from the back box. Remove the dust from the lower dome using compressed air from a spray can.  
Replace the lower dome following the installation instructions that were shipped with it.  
Warning: Proper eye protection should be worn when using compressed air cans.  
90  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Specifications  
16X MODELS  
DD4TC16  
Signal Format  
NTSC  
Scanning System  
Image Sensor  
Effective Pixels  
Horizontal Resolution  
Lens  
Zoom Speed (optical range)  
Horizontal Angle of View  
Focus  
Maximum Sensitivity at 35 IRE  
Sync System  
2:1 Interlace  
1/4-inch interline transfer CCD  
768 (H) X 494 (V)  
>470 TV lines  
f/1.4 (focal length, 4~64 mm; 16X optical zoom, 8X digital zoom)  
1.9/3.6/6.0 seconds  
43° at 4 mm wide zoom; 3° at 64 mm telephoto zoom  
Automatic with manual override  
0.05 lux at 1/2 sec. shutter speed (color)  
AC line lock, phase adjustable using remote control, V-Sync  
Automatic (electronic iris)/manual; 1/2 ~ 1/30,000  
Automatic iris control with manual override  
Automatic with manual override  
1 Vp-p, 75 ohms  
Shutter Speed  
Iris Control  
Gain Control  
Video Output  
Video Signal-to-Noise  
>50 dB  
DD4TC16-X  
Signal Format  
PAL  
Scanning System  
Image Sensor  
Effective Pixels  
Horizontal Resolution  
Lens  
Zoom Speed (optical range)  
Horizontal Angle of View  
Focus  
Maximum Sensitivity at 35 IRE  
Sync System  
2:1 Interlace  
1/4-inch interline transfer CCD  
752 (H) X 582 (V)  
>460 TV lines  
f/1.4 (focal length, 4~64 mm; 16X optical zoom, 8X digital zoom)  
1.9/3.6/6.0 seconds  
43° at 4 mm wide zoom; 3° at 64 mm telephoto zoom  
Automatic with manual override  
0.05 lux at 1/1.5 sec. shutter speed (color)  
AC line lock, phase adjustable using remote control, V-Sync  
Automatic (electronic iris)/manual; 1/1.5~1/30,000  
Automatic iris control with manual override  
Automatic with manual override  
1 Vp-p, 75 ohms  
Shutter Speed  
Iris Control  
Gain Control  
Video Output  
Video Signal-to-Noise  
>50 dB  
C3412M-D (12/08)  
91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
18X MODELS  
DD4CBW18  
Signal Format  
NTSC  
Scanning System  
Image Sensor  
Effective Pixels  
2:1 Interlace  
1/4-inch progressive scan CCD  
768 (H) X 494 (V)  
Horizontal Resolution  
Lens  
Zoom Speed (optical range)  
Horizontal Angle of View  
Focus  
540 TV lines  
f/1.6 (focal length, 3.8~68.4 mm; 18X optical zoom, 12X digital zoom)  
2.9/4.2/5.8 seconds  
51° at 3.8 mm wide zoom; 3° at 68.4 mm telephoto zoom  
Automatic with manual override  
Maximum Sensitivity at 35 IRE  
0.025 lux at 1/2 sec. shutter speed (color)  
0.1 lux at 1/60 sec. shutter speed (B-W)  
0.004 lux at 1/2 sec. shutter speed (B-W)  
Sync System  
Internal/AC line lock, phase adjustable using remote control, V-Sync  
Automatic with manual override  
Automatic (electronic iris)/manual; 1/2~1/30,000  
Automatic iris control with manual override  
Automatic/off  
White Balance  
Shutter Speed  
Iris Control  
Gain Control  
Video Output  
Video Signal-to-Noise  
1 Vp-p, 75 ohms  
>50 dB  
DD4CBW18-X  
Signal Format  
PAL  
Scanning System  
Image Sensor  
Effective Pixels  
2:1 Interlace  
1/4-inch progressive scan CCD  
752 (H) X 582 (V)  
Horizontal Resolution  
Lens  
Zoom Speed (optical range)  
Horizontal Angle of View  
Focus  
540 TV lines  
f/1.6 (focal length, 3.8~68.4 mm; 18X optical zoom, 12X digital zoom)  
2.9/4.2/5.8 seconds  
51° at 3.8 mm wide zoom; 3° at 68.4 mm telephoto zoom  
Automatic with manual override  
Maximum Sensitivity at 35 IRE  
0.025 lux at 1/1.5 sec. shutter speed (color)  
0.1 lux at 1/50 sec. shutter speed (B-W)  
0.004 lux at 1/1.5 sec. shutter speed (B-W)  
Sync System  
Internal/AC line lock, phase adjustable using remote control, V-Sync  
Automatic with manual override  
Automatic (electronic iris)/manual; 1/1.5~1/30,000  
Automatic iris control with manual override  
Automatic/off  
White Balance  
Shutter Speed  
Iris Control  
Gain Control  
Video Output  
Video Signal-to-Noise  
1 Vp-p, 75 ohms  
>50 dB  
92  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
22X MODELS  
DD4C22  
Signal Format  
NTSC  
Scanning System  
Image Sensor  
2:1 Interlace  
1/4-inch CCD  
Effective Pixels  
Horizontal Resolution  
Lens  
Zoom Speed (optical range)  
Horizontal Angle of View  
Focus  
Maximum Sensitivity at 35 IRE  
Sync System  
White Balance  
768 (H) X 494 (V)  
>470 TV lines  
f/1.6 (focal length, 4~88 mm; 22X optical zoom, 12X digital zoom)  
2.4/3.9/6.3 seconds  
47° at 4 mm wide zoom; 2.2° at 88 mm telephoto zoom  
Automatic with manual override  
0.02 lux at 1/2 sec. shutter speed  
Internal/AC line lock, phase adjustable using remote control, V-Sync  
Automatic with manual override  
Automatic (electronic iris)/manual; 1/2~1/30,000  
Automatic iris control with manual override  
Automatic/off  
Shutter Speed  
Iris Control  
Gain Control  
Video Output  
1 Vp-p, 75 ohms  
Video Signal-to-Noise  
>50 dB  
DD4C22-X  
Signal Format  
PAL  
Scanning System  
Image Sensor  
2:1 Interlace  
1/4-inch CCD  
Effective Pixels  
Horizontal Resolution  
Lens  
Zoom Speed (optical range)  
Horizontal Angle of View  
Focus  
Maximum Sensitivity at 35 IRE  
Sync System  
White Balance  
752 (H) X 582 (V)  
>460 TV lines  
f/1.6 (focal length, 4~88 mm; 22X optical zoom, 12X digital zoom)  
2.4/3.9/6.3 seconds  
47° at 4 mm wide zoom; 2.2° at 88 mm telephoto zoom  
Automatic with manual override  
0.02 lux at 1/1.5 sec. shutter speed  
Internal/AC line lock, phase adjustable using remote control, V-Sync  
Automatic with manual override  
Automatic (electronic iris)/manual; 1/1.5~1/30,000  
Automatic iris control with manual override  
Automatic/off  
Shutter Speed  
Iris Control  
Gain Control  
Video Output  
1 Vp-p, 75 ohms  
Video Signal-to-Noise  
>50 dB  
C3412M-D (12/08)  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
23X MODELS  
DD4CBW23  
Signal Format  
NTSC  
Scanning System  
Image Sensor  
Effective Pixels  
2:1 Interlace  
1/4-inch progressive scan CCD  
768 (H) X 494 (V)  
Horizontal Resolution  
Lens  
Zoom Speed (optical range)  
Horizontal Angle of View  
Focus  
540 TV lines  
f/1.6 (focal length, 3.6~82.8 mm; 23X optical zoom, 12X digital zoom)  
2.9/4.2/5.8 seconds  
54° at 3.6 mm wide zoom; 2.5° at 82.8 mm telephoto zoom  
Automatic with manual override  
Maximum Sensitivity at 35 IRE  
0.025 lux at 1/2 sec. shutter speed (color)  
0.1 lux at 1/60 sec. shutter speed (B-W)  
0.004 lux at 1/2 sec. shutter speed (B-W)  
Sync System  
Internal/AC line lock, phase adjustable using remote control, V-Sync  
White Balance  
Shutter Speed  
Iris Control  
Automatic with manual override  
Automatic (electronic iris)/manual; 1/2~1/30,000  
Automatic iris control with manual override  
Gain Control  
Video Output  
Video Signal-to-Noise  
Wide Dynamic Range  
Automatic/off  
1 Vp-p, 75 ohms  
>50 dB  
80X  
94  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DD4CBW23-X  
Signal Format  
PAL  
Scanning System  
Image Sensor  
Effective Pixels  
Horizontal Resolution  
Lens  
2:1 Interlace  
1/4-inch progressive scan CCD  
752 (H) X 582 (V)  
540 TV lines  
f/1.6 (focal length, 3.6~82.8 mm; 23X optical zoom, 12X digital zoom)  
2.9/4.2/5.8 seconds  
Zoom Speed  
Horizontal Angle of View  
Focus  
54° at 3.6 mm wide zoom; 2.5° at 82.8 mm telephoto zoom  
Automatic with manual override  
Maximum Sensitivity at 35 IRE  
0.025 lux at 1/1.5 sec. shutter speed (color)  
0.1 lux at 1/50 sec. shutter speed (B-W)  
0.004 lux at 1/1.5 sec. shutter speed (B-W)  
Sync System  
Internal/AC line lock, phase adjustable using remote control, V-Sync  
White Balance  
Shutter Speed  
Iris Control  
Automatic with manual override  
Automatic (electronic iris)/manual; 1/1.5~1/30,000  
Automatic iris control with manual override  
Gain Control  
Video Output  
Video Signal-to-Noise  
Wide Dynamic Range  
Automatic/off  
1 Vp-p, 75 ohms  
>50 dB  
80X  
C3412M-D (12/08)  
95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35X MODELS  
DD4CBW35  
Signal Format  
NTSC  
Scanning System  
Image Sensor  
2:1 Interlace/1:1 Progressive (user-selectable)  
1/4-inch CCD  
Effective Pixels  
768 (H) X 494 (V)  
Horizontal Resolution  
Lens  
Zoom Speed (optical range)  
Horizontal Angle of View  
Focus  
>540 TV lines  
f/1.4 (focal length, 3.4~119 mm; 35X optical zoom, 12X digital zoom)  
3.2/4.6/6.6 seconds  
55.8° at 3.4 mm wide zoom; 1.7° at 119 mm telephoto zoom  
Automatic with manual override  
Maximum Sensitivity at 35 IRE  
0.55 lux at 1/60 sec. shutter speed (color)  
0.063 lux at 1/4 sec. shutter speed (color)  
0.00018 lux at 1/2 sec. shutter speed (B-W)  
Sync System  
Internal/AC line lock, phase adjustable using remote control, V-Sync  
White Balance  
Shutter Speed  
Iris Control  
Automatic with manual override  
Automatic (electronic iris)/manual; 1/2~1/30,000  
Automatic iris control with manual override  
Gain Control  
Video Output  
Video Signal-to-Noise  
Wide Dynamic Range  
Automatic/off  
1 Vp-p, 75 ohms  
>46–50 dB  
128X  
96  
C3412M-D (12/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DD4CBW35-X  
Signal Format  
PAL  
Scanning System  
Image Sensor  
2:1 Interlace/1:1 Progressive (user-selectable)  
1/4-inch CCD  
Effective Pixels  
Horizontal Resolution  
Lens  
752 (H) X 582 (V)  
>540 TV lines  
f/1.4 (focal length, 3.4~119 mm; 35X optical zoom, 12X digital zoom)  
3.2/4.6/6.6 seconds  
Zoom Speed  
Horizontal Angle of View  
Focus  
55.8° at 3.4 mm wide zoom; 1.7° at 119 mm telephoto zoom  
Automatic with manual override  
Maximum Sensitivity at 35 IRE  
0.50 lux at 1/50 sec. shutter speed (color)  
0.062 lux at 1/3 sec. shutter speed (color)  
0.00014 lux at 1/1.5 sec. shutter speed (B-W)  
Sync System  
Internal/AC line lock, phase adjustable using remote control, V-Sync  
White Balance  
Shutter Speed  
Iris Control  
Automatic with manual override  
Automatic (electronic iris)/manual; 1/1.5~1/30,000  
Automatic iris control with manual override  
Gain Control  
Video Output  
Video Signal-to-Noise  
Wide Dynamic Range  
Automatic/off  
1 Vp-p, 75 ohms  
>46–50 dB  
128X  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the  
European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures  
for recycling this equipment.  
C3412M-D (12/08)  
97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in  
material or workmanship for a period of one year after the date of shipment.  
Pelco will warrant all replacement parts and repairs for 90 days from the date of  
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid  
to a Pelco designated location. Repairs made necessary by reason of misuse,  
alteration, normal wear, or accident are not covered under this warranty.  
Exceptions to this warranty are as noted below:  
Five years:  
Pelco assumes no risk and shall be subject to no liability for damages or loss  
resulting from the specific use or application made of the Products. Pelcos  
liability for any claim, whether based on breach of contract, negligence,  
infringement of any rights of any party or product liability, relating to the  
Products shall not exceed the price paid by the Dealer to Pelco for such  
Products. In no event will Pelco be liable for any special, incidental, or  
consequential damages (including loss of use, loss of profit, and claims of third  
parties) however caused, whether by the negligence of Pelco or otherwise.  
Fiber optic products  
TW3000 Series unshielded twisted pair (UTP) transmission products  
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and  
MC3651H-2X camera models  
Three years:  
Pelco-branded fixed camera models (CCC1390H Series, C10DN Series,  
C10CH Series, and IP3701H Series)  
EH1500 Series enclosures  
The above warranty provides the Dealer with specific legal rights. The Dealer  
may also have additional rights, which are subject to variation from state to  
state.  
Spectra® IV products (including Spectra IV IP)  
Camclosure® Series (IS, ICS, IP) integrated camera systems  
DX Series digital video recorders, DVR5100 Series digital video  
recorders, Digital Sentry® Series hardware products, DVX Series digital  
video recorders, and NVR300 Series network video recorders  
Endura® Series distributed network-based video products  
Genex® Series products (multiplexers, server, and keyboard)  
PMCL200/300/400 Series LCD monitors  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100  
or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the  
following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number  
3. Details of the defect or problem  
Two years:  
If there is a dispute regarding the warranty of a product that does not fall  
Standard motorized or fixed focal length lenses  
DF5/DF8 Series fixed dome products  
Legacy® Series integrated positioning systems  
Spectra III, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, and PS20  
scanners, including when used in continuous motion applications.  
Esprit Ti and TI2500 Series thermal imaging products  
Esprit and WW5700 Series window wiper (excluding wiper blades).  
CM6700/CM6800/CM9700 Series matrix  
Digital Light Processing (DLP®) displays (except lamp and color wheel).  
The lamp and color wheel will be covered for a period of 90 days. The  
air filter is not covered under warranty.  
Intelli-M® eIDC controllers  
under the warranty conditions stated above, please include  
explanation with the product when returned.  
a
written  
Method of return shipment shall be the same or equal to the method by which  
the item was received by Pelco.  
RETURNS  
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100  
or (559) 292-1981 to obtain an authorization number (CA number if returned for  
credit, and RA number if returned for repair) and designated return location.  
All merchandise returned for credit may be subject to a 20 percent restocking  
and refurbishing charge.  
One year:  
Video cassette recorders (VCRs), except video heads. Video heads will  
be covered for a period of six months.  
Six months:  
All pan and tilts, scanners, or preset lenses used in continuous motion  
applications (preset scan, tour, and auto scan modes).  
Goods returned for repair or credit should be clearly identified with the  
assigned CA or RA number and freight should be prepaid  
11-11-08  
REVISION HISTORY  
Manual #  
C3412M  
Date  
9/06  
Comments  
Original version.  
C3412M-A  
C3412M-B  
10/06  
6/07  
Upgraded 23X to Spectra IV SE and added 18X information. Corrected specifications. Revised SW2 Switches 4–5 section.  
Corrected menus and Specifications. Added cross references. Added information about low light focus, event labels, and image  
enhancement features.  
C3412M-C  
C3412M-D  
11/07  
12/08  
Updated manual to reflect software version 1.070. Added DIP switch and progressive scan sections. Revised switch settings, type of  
lighting, IR cut filter, and proportional pan settings.  
Updated to reflect software version 1.090. Added new sections for sure focus, event types, low lux noise reduction, sensor scan mode,  
and field align. Revised information regarding SW2-3, type of lighting settings, 18X and 23X specifications, auto white balance defaults,  
and limitations to presets. Removed all references to 22X black-white models.  
Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.  
Spectra III is a trademark of Pelco, Inc.  
© Copyright 2008, Pelco, Inc. All rights reserved.  
DLP is a registered trademark of Texas Instruments Incorporated.  
Vicon is a registered trademark of Vicon Industries, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA  
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150  
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peavey Computer Monitor 10PM User Manual
Peerless Industries TV Mount ST632 User Manual
Pelco Satellite Radio FR85081 User Manual
Philips Car Video System 170V9 User Manual
Philips Computer Drive FM02SW00 00 User Manual
Philips Microphone SBCM D110 User Manual
Philips MP3 Player AJL700 User Manual
Pioneer DVD Player DVR 320 S User Manual
PLUS Vision Projector U5 232 User Manual
PYLE Audio Car Satellite TV System PLRD195IF User Manual