Pelco Car Amplifier cs73m d User Manual

IMPORTANT NOTICE

Date January 5, 2008

Manual Affected CM9760-MDA System 9760^®Master Distribution Amplifier Installation/Operation Manual, C573M-D

Manual Update The connection of a PC to multiple MDA units as illustrated in Figure 40 is not supported. Please disregard Figure 40 and

all applicable references.

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

Pelco, the Pelco logo, and System 9760 are registered trademarks of Pelco, Inc.

Pelco, Inc. Worldwide Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com

USA & Canada • Tel: 800/289-9100 • Fax: 800/289-9150

International • Tel: 1-559/292-1981 • Fax: 1-559/348-1120

C1596M

Download from Www.Somanuals.com. All Manuals Search And Download.

SYSTEM

Master DistributCioMn9A7m60p-lMifDieAr

CM9760-MDA

System 9760^®

Master Distribution

Amplifier

Installation/

Operation Manual

C573M-D (11/03)

Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com

USA & Canada: Tel: 800/289-9100 • Fax: 800/289-9150

International: Tel: 1-559/292-1981 • Fax: 1-559/348-1120

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

Section

Page

IMPORTANT SAFEGUARDS AND WARNINGS................................................................4

DESCRIPTION ...................................................................................................................4

OVERVIEW ................................................................................................................4

MODELS ....................................................................................................................6

MOUNTING ........................................................................................................................6

HARDWARE SETUP .........................................................................................................6

COMMUNICATION ....................................................................................................6

COMMUNICATION PORTS SETUP ..........................................................................7

ADDRESS SETUP FOR DAISY CHAINING ..............................................................8

SETTING UP A UNIT AS THE MASTER CLOCK ......................................................9

RESETTING TO FACTORY DEFAULTS....................................................................9

CLEARING TITLE/TIME/DATE TEXT DISPLAY ON ALL CHANNELS .....................10

VIDEO CONNECTIONS ...........................................................................................10

DATA CONNECTIONS .............................................................................................. 11

CONNECTING THE MDA TO A SYSTEM 9740/9760

CONTROLLER ................................................................................................. 11

CONNECTING THE MDA TO AN EXTERNAL PC ...........................................12

CONNECTING THE MDA TO A CM9760-KBD KEYBOARD ............................13

CONNECTING THE MDA TO A KBD200A OR KBD300A KEYBOARD ...........13

POWER CONNECTIONS .........................................................................................14

PROGRAMMING ..............................................................................................................15

TIME AND DATE SETUP ..........................................................................................15

PROGRAMMING METHODS ...................................................................................15

PROGRAMMING WITH A KEYBOARD ....................................................................15

KEYBOARD KEYS AND JOYSTICK ................................................................15

ENTERING THE PROGRAMMING MODE WITH THE CM9760-KBD .............16

ENTERING THE PROGRAMMING MODE WITH THE KBD200A OR

KBD300A KEYBOARD .....................................................................................16

MAIN MENU .....................................................................................................17

SET CAMERA TITLE ........................................................................................17

SET CABLE COMPENSATION ........................................................................18

SET CAMERA DISPLAY ...................................................................................18

SET TIME AND DATE .......................................................................................20

SET PORT ........................................................................................................21

RESET MDA .....................................................................................................22

PROGRAMMING WITH THE CM9760-MDA SETUP PROGRAM ............................22

CM9760-MDA SETUP PROGRAM DESCRIPTION .........................................22

SYSTEM REQUIREMENTS .............................................................................22

INSTALLING THE CM9760-MDA SETUP PROGRAM .............................................23

STARTING THE CM9760-MDA SETUP PROGRAM ................................................24

CM9760-MDA SETUP DIALOG BOX ...............................................................25

SET PASSWORD .............................................................................................25

SET UNIT ID .....................................................................................................26

SET SYSTEM ...................................................................................................26

SET TIME AND DATE .......................................................................................28

SET TITLES ......................................................................................................29

SET CABLE COMPENSATION ........................................................................31

SET DISPLAY ...................................................................................................32

SET MESSAGE TEXT ......................................................................................34

SEND DATA ......................................................................................................40

VIDEO ALPHANUMERIC OVERLAYS .....................................................................40

TROUBLESHOOTING ......................................................................................................41

SPECIFICATIONS.............................................................................................................42

APPENDIX A – APPLICATIONS .......................................................................................44

APPENDIX B – SUPPORTED TITLE AND MESSAGE TEXT CHARACTERS.................56

APPENDIX C – MESSAGE TEXT INSERTION COMMANDS ..........................................57

WARRANTY AND RETURN INFORMATION....................................................................60

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

LIST OF ILLUSTRATIONS

Figure

Page

System Configuration (Rear Panel View)...........................................................5

Location of DIP Switches ...................................................................................7

DIP Switch..........................................................................................................7

Connecting the MDA to a System 9760 ............................................................ 11

PC Connection to CM9760-MDA ......................................................................12

CM9760-KBD Setup for Direct Control .............................................................13

Keyboard Rear Panel ........................................................................................13

CM9760-MDA Keyboard Wiring ........................................................................14

Main Menu ........................................................................................................17

Set Camera Title Menu .....................................................................................17

Set Cable Compensation Menu ........................................................................18

Set Camera Display Menu ................................................................................18

Set Time and Date Menu ..................................................................................20

Set Port Menu ...................................................................................................21

Reset CM9760-MDA Screen .............................................................................22

CM9760-MDA Setup Dialog Box .......................................................................24

Old Password Dialog Box .................................................................................25

New Password Dialog Box ................................................................................25

Unit ID Dialog Box .............................................................................................26

MDA COM 1 Setup Dialog Box .........................................................................26

System Communication Setup Dialog Box .......................................................27

Set Time and Date Dialog Box ..........................................................................28

Setting Titles Using the CM9760-MDA SETUP Dialog Box ..............................29

Set Cable Compensation Dialog Box................................................................31

Display Dialog Box ............................................................................................32

Position Text Dialog Box ...................................................................................33

Adjust Brightness Dialog Box ............................................................................33

Output On/Off Dialog Box .................................................................................33

Input On/Off Dialog Box ....................................................................................33

Message Text Editing Dialog Box......................................................................34

Command Data Window ...................................................................................35

Sample Display Screen Example ......................................................................37

Sample Command Data Window ......................................................................38

Typical Camera Display With Alphanumerics ...................................................40

CM9760-MDA Dimension Drawing ...................................................................43

Simple System Configuration ............................................................................45

Master MDA Time and Date Generator for 63 MDA Slave Units

(64 Total MDA Units) .........................................................................................46

PC Connection to Up to 16 Daisy-Chained MDA Units .....................................47

PC Connection to over 16 MDA Units (Maximum of 64 MDA Units) .................48

CM9760-CC1 Connection to up to 16 Daisy-Chained MDA Units ....................49

CM9760-CC1 Connection to over 16 MDA Units

(Maximum of 64 MDA Units) .............................................................................50

MDA Connected to Multiplexers ........................................................................51

Non-Coaxitron System Setup ...........................................................................52

Coaxitron with System 9760 Setup ...................................................................53

Coaxitron with System 6800 Setup ...................................................................54

CM9760-MDA Message Text Sent from Third-Party Equipment .......................55

LIST OF TABLES

Table

Page

Port Setup Switch Settings ................................................................................7

Address Switch Settings ....................................................................................8

Video Coaxial Cable Wiring Distances..............................................................10

MDA RJ-45 Connector Pin-Outs .......................................................................12

CM9760-CC1/CM9760-MDA Format Matchup .................................................20

CM9760-CC1/CM9760-MDA Compatible Date Styles and Time Formats ........29

Supported Title and Message Text Character Set.............................................56

CM9760-MDA Message Text Insertion Commands ..........................................57

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFEGUARDS AND WARNINGS

Observe the following WARNINGS before installing and using this product.

1. Installation and servicing should be done by qualified service personnel only and

conform to all local codes.

2. Unless the unit meets NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P standards, it is designed

for indoor use only and must not be installed where exposed to rain and moisture.

3. Only use replacement parts Pelco recommends.

4. After replacing/repairing this unit’s electrical components, conduct a resistance

measurement between line and exposed parts to verify the exposed parts have not

been connected to line circuitry.

The product and/or manual may bear the following marks:

This symbol indicates that

dangerous voltage constituting a

risk of electric shock is present

within this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that there

are important operating and

maintenance instructions in the

literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation

and operation.

DESCRIPTION

OVERVIEW

The CM9760 master distribution amplifier (CM9760-MDA), version 2.05 or higher, is a

16-channel video distribution amplifier that distributes video to multiple devices without

image degradation. As illustrated in Figure 1, each of the 16 channels (video inputs) has

four independent video outputs. Each of the video outputs can be connected to any of the

following devices:

•

Monitor

Video printer

Video cassette recorder (VCR)

Digital video recorder (DVR)

Multiplexer

Matrix switcher

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

CAMERA

CAMERA INPUT

INPUT

120VAC

PGM

MON

COM1COM2

UNIT ID

OUTPUT

PELCO CM9760-MDA

PELCO SYSTEM CM9760 OR

PC CONNECTED TO COM1 PORT

MONITOR

VCR

Figure 1. System Configuration (Rear Panel View)

The MDA can be programmed using a PC or a CM9760-KBD, KBD200A, or KBD300A

keyboard. Each of the 16 video inputs can be individually programmed to insert time/date

and title information on each video output, and each video output is selectable to include or

exclude time/date and title generation. Character positions are adjustable horizontally and

vertically on-screen with digital brightness control. Programming also includes cable

compensation for up to 1,500 feet (457 m) of RG59/U coaxial cable.

The MDA can act as a stand-alone time/date and title generator or can be synchronized to

a System 9740^™/System 9760^®as a matrix time/date and title generator:

•

As a stand-alone unit, an MDA can be addressed to provide the master time and date

for up to 63 MDA slave units.

NOTE: Up to 16 MDA units

can be daisy-chained. If

more than 16 MDAs are

required, a CM9760-CDU-T

must be used.

When connected to a System 9740/System 9760 CC1 port, up to 64 MDAs can accept

the master time and date from the 9740/9760.

In addition, note the following about the MDA:

•

Using the RS-232 or RS-422 communication standard, the MDA can accept text

messages from third-party equipment. A message can contain up to 24 characters. Up

to five lines of messages can be displayed simultaneously. The messages can be

inserted onto any video channel independently. For additional information, refer to the

Set Message Text section of this manual.

•

All video inputs are individually ground isolated to prevent ground loops, eliminating

the need for ground loop isolation transformers.

•

Battery backup protects programming information for a minimum of one year.

The MDA does not pass Coaxitron^®signals; however, the MDA can be used with

Coaxitron products such as the CM6700, CM6800, and the CM9760-CXTA.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

MODELS

CM9760-MDA

Master distribution amplifier with time and date and title, 120 VAC,

60 Hz (FCC)

CM9760-MDA-X

Same as CM9760-MDA except 230 VAC, 50 Hz (CE)

MOUNTING

Install the MDA in a standard 19-inch (48.26 cm) equipment rack using standard mounting

hardware. The MDA occupies 5.25 inches (13.34 cm) of vertical space, or three RU (rack

units).

VERY IMPORTANT: If

you are going to use RS-232

communication, you must

open the case to set the DIP

switches—do so BEFORE

mounting the MDA unit in

the rack. See the section on

Communication Ports Setup

and the section on Connect-

ing the MDA to an External

PC for information.

HARDWARE SETUP

The following parts are supplied:

CM9760 Master Distribution Amplifier

Power cord

Data cable (reversed RJ-45 to RJ-45)

CM9760-MDA Resource CD

COMMUNICATION

Communication between MDA units, System 9760 CC1 (controller), System 9740 CC1 (con-

troller), KBD200A or KBD300A keyboard, or a host PC is accomplished using serial RS-232,

RS-422, or RS-485 transceivers that can be configured by DIP switches on the PCB (printed

circuit board). The factory default for both COM 1 and COM 2 ports is RS-422.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

COMMUNICATION PORTS SETUP

NOTE: COM 1 is config-

ured at the factory for

RS-422 communication. To

communicate via RS-232,

you must open the case and

change an internal DIP

switch.

There are two sets of DIP switches inside the MDA for selecting the type of interface for the

communication ports (COM 1 and COM 2).

The unit comes from the factory configured for RS-422. If your communication scheme is

RS-422 and you intend to program the MDA(s) through a CM9760-KBD, KBD200A or

KBD300A keyboard, leave the settings alone.

However, if the communication scheme is different than RS-422, or you are going to

program the MDA through a PC (which requires RS-232), do the following to change

settings. (Generally, programming through a PC is easier than programming through a

System 9760 keyboard. For more information, refer to the Programming section.)

1. Remove the 10 screws on the top cover and lift it off.

2. Refer to Figure 2 for the location of the switches for COM 1 and COM 2. Refer to

Table A for the switch settings.

3. Replace the cover.

COM 2

COM 1

UNIT ID DIP SWITCH

BACK

FUSE

COM 1 DIP SWITCH

COM 2 DIP SWITCH

FRONT

Figure 2. Location of DIP Switches

Table A. Port Setup Switch Settings

SWITCH SETTINGS

PORT SETUP

SELECTED

OFF OFF OFF OFF ON

ON OFF OFF

ON OFF OFF OFF OFF

ON OFF OFF ON OFF

RS-232 Operation

RS-422 Operation*

RS-485 Operation

1 2 3 4 5 6 7 8

Figure 3. DIP Switch

* Factory default setting

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

ADDRESS SETUP FOR DAISY CHAINING

NOTE: When upgrading

CM9760-MDA units in a

daisy chain to version 2.xx,

version 2.xx units must be

the first units in the daisy

chain. Any CM9760-MDA

version 1.xx units must be

connected in the chain fol-

lowing all version 2.xx units.

CAUTION: Switch 7 clears all entered data from memory.

Table B. Address Switch Settings

SWITCH SETTINGS

CAMERA RANGE SELECTED

OFF

Cameras 1-16

Cameras 17-32

OFF

Cameras 33-48

Cameras 49-64

OFF

Cameras 65-80

Cameras 81-96

OFF

Cameras 97-112

Cameras 113-128

Cameras 129-144

Cameras 145-160

Cameras 161-176

Cameras 177-192

Cameras 193-208

Cameras 209-224

Cameras 225-240

Cameras 241-256

Cameras 257-272

Cameras 273-288

Cameras 289-304

Cameras 305-320

Cameras 321-336

Cameras 337-352

Cameras 353-368

Cameras 369-384

Cameras 385-400

Cameras 401-416

Cameras 417-432

Cameras 433-448

Cameras 449-464

Cameras 465-480

Cameras 481-496

Cameras 497-512

Cameras 513-528

Cameras 529-544

Cameras 545-560

Cameras 561-576

Cameras 577-592

Cameras 593-608

Cameras 609-624

Cameras 625-640

OFF

(Continued on next page)

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. Address Switch Settings (Continued)

SWITCH SETTINGS

CAMERA RANGE SELECTED

OFF

Cameras 641-656

Cameras 657-672

Cameras 673-688

Cameras 689-704

Cameras 705-720

Cameras 721-736

Cameras 737-752

Cameras 753-768

Cameras 769-784

Cameras 785-800

Cameras 801-816

Cameras 817-832

Cameras 833-848

Cameras 849-864

Cameras 865-880

Cameras 881-896

Cameras 897-912

Cameras 913-928

Cameras 929-944

Cameras 945-960

Cameras 961-976

Cameras 977-992

Cameras 993-1008

Cameras 1009-1024

OFF

SETTING UP A UNIT AS THE MASTER CLOCK

You can synchronize several CM9760-MDAs even when connecting them without a

CM9760 switching system. The master clock can be any unit ID as long as it is the first unit

of the chain. Make it the master clock by turning on switch 8 of the unit ID DIP switch on the

rear panel. This unit will synchronize the time and date of all units connected to it. Only one

unit can be a master clock. The remaining units are the slave units (unit ID DIP switch 8 is

in the OFF position, which is the default setting). A single MDA unit can provide the master

time and date for up to 63 slave units.

RESETTING TO FACTORY DEFAULTS

CAUTION:

Switch 7 clears all

entered data from

memory.

You can reset the CM9760-MDA to factory defaults by turning on switch 7 of the UNIT ID

DIP switch located on the rear panel. Do this before powering up the unit. Now, turn on the

CM9760-MDA. This will clear all data stored in memory, such as titles and port configura-

tions and resets them to the defaults as shipped from the factory. Then turn off the

CM9760-MDA and turn switch 7 off.

DO NOT turn off the

MDA before the reset

process finishes. This

can lock up the MDA and

render it useless. The

length of time to leave

power on can vary from a

few seconds to several min-

utes (for systems with a lot

of equipment). To determine

when the process finishes,

look at the monitor outputs

as resetting puts everything

back to default status.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

CLEARING TITLE/TIME/DATE TEXT DISPLAY ON ALL CHANNELS

You can clear title/time/date text on all CM9760-MDA channels using a DIP switch method.

To do so, proceed as follows:

1. Turn off the MDA.

2. Set the MDA to unit ID 33:

a. Set DIP switches 1, 2, 3, 4, and 5 to the OFF position.

b. Set DIP switch 6 to the ON position.

3. Turn on the MDA.

A 30-second timer starts.

4. Before the 30 seconds elapses, change the unit ID to a setting other than unit ID 33

using the appropriate DIP switch settings.

After 30 seconds have elapsed, the MDA checks whether the unit ID is different from

the initial setting of 33. If the unit ID has changed, the MDA title/time/date text display

is cleared.

Note the following:

•

The title/time/date text can be programmed again using the PC or a CM9760-KBD,

KBD200A, or KBD300A keyboard.

If the MDA must be set back to unit ID 33, set the unit ID after the title/time/date text

has cleared.

VIDEO CONNECTIONS

Table C. Video Coaxial Cable Wiring Distances

Cable Type*

Maximum Distance

750 ft (229 m)

RG59/U

RG6/U

1,000 ft (305 m)

1,500 ft (457 m)

RG11/U

*Minimum cable requirements:

75 ohms impedance

All-copper center conductor

All-copper braided shield with 95% braid coverage

1. Connect the remote video sources to the input BNC connectors on the rear panel of

the MDA (refer to Figure 33). Refer to Table C for video coaxial wiring distances. (Note

that when wiring inputs it is good installation practice to label each video input in case

troubleshooting is required.)

2. Connect cables from the output BNC connectors on the MDA’s rear panel to the input

connectors of monitors, VCRs, switchers, etc. (refer to Figure 33). Refer to Table C for

video coaxial wiring distances.

Although the MDA does not pass Coaxitron signals, it can be used with Coaxitron products

—such as the CM6700, CM6800, and CM9760-CXTA—by installing the MDA after the

Coaxitron equipment (refer to Figure 45 and to Figure 46).

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

DATA CONNECTIONS

The MDA can be connected to an external device via RS-232/422/485 standards. The

distance at which it can be installed away from another device depends on the communica-

tion type and the wire size of the cable. Maximum cable distance for RS-232 serial data for

18-24 AWG is 50 feet (15.24 m) while the maximum for RS-422 and RS-485 with 24-gauge

wire is 4,000 feet (1,219 m). For longer distances, junction boxes and heavier cable can be

used. Pelco recommends using shielded twisted pair, such as Belden 9843 or similar cable,

meeting or exceeding the basic requirements for EIA RS-422/485 applications. Decide

where the MDA will be located and follow the mounting and connection instructions.

CONNECTING THE MDA TO A SYSTEM 9740/9760

CONTROLLER

The rear panel of the MDA contains two RJ-45 modular connectors for external data

communication using RS-232, RS-422, or RS-485 standards. Connect the COM 1 port on

the MDA’s rear panel to the next available RJ-45 output connector on the System 9740/9760

controller (refer to Figure 4 for an illustration of MDA connection to a System 9760 control-

ler.) The System 9740/9760 controller port to which the MDA is connected must be

programmed for proper communication with an MDA. Refer to the System CM9760-CC1

manual or to the System CM9740-CC1 manual for information about selecting and

configuring the RJ-45 ports on the System 9740/9760 controller.

USE NEXT

AVAILABLE

PORT

MDA COM 1 PORT

Figure 4. Connecting the MDA to a System 9760

Refer to Figure 37 and to Figure 38 for illustrations of connecting multiple MDA units to a

System 9760 controller.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING THE MDA TO AN EXTERNAL PC

Perform this step if you are going to program your CM9760-MDA unit using a PC (personal

computer).

NOTE: The CM9760-MDA

is configured at the factory

for RS-422 communication.

To communicate via RS-232,

an internal DIP switch must

be changed. Refer to the

Communication Ports Setup

section.

Refer to Figure 5 and make a cable to connect the MDA to the PC. The figure shows a

typical nine-pin sub “D” connector for the PC’s COM 1/COM 2 serial port. Computers may

differ regarding connector types and pin-outs. Therefore, always refer to the computer’s

manual to determine proper pin-outs.

If more than one MDA is to be programmed using a PC, note the following:

•

A maximum of 16 MDA units can be daisy-chained. To daisy-chain up to 16 MDA units,

connect the RS-422 output of the first MDA unit to the RS-422 input of the second

MDA unit and continue this method until the last MDA unit is connected (refer to Table

D and to Figure 39).

If more than 16 MDAs are to be connected to a PC, a CM9760-CDU-T must be used.

Refer to Figure 40 for an example of connecting over 16 MDAs to a PC. Note that a

maximum of 64 MDA units can be connected to a PC for programming.

Table D. MDA RJ-45 Connector Pin-Outs

Pin Out

RS-232 Function

RS-422 Function

RS-485 Function

Transmit

Transmit +

Transmit -

No Connection

Ground

Transmit +

Transmit -

No Connection

Ground

No Connection

Ground

No Connection

Receive

No Connection

Receive -

No Connection

Receive -

Receive +

MDA SIDE

CM9760-MDA

PIN 8

PIN 1

120V

PGM

MON

PC SIDE

COM1

COM2

COM1 RJ-45

CONNECTOR

UNI

NOTE: The pin numbering

of the wall block shown in

Figure 5 applies to the Pelco

RJ-45 wall block. A wall

block purchased from a

supplier other than Pelco

may have a different pin

numbering scheme.

REVERSED CABLE

RJ-45

COMPUTER

TRANSMIT

COMPUTER

RECEIVE

CONNECTOR

REVERSED CABLE CONNECTIONS

WALL BLOCK

RJ-45

CONNECTOR

CM9760-MDA

RJ-45

CONNECTOR

PIN 1=TX

PIN 8=RX

GROUND

WALL BLOCK

Figure 5. PC Connection to CM9760-MDA

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING THE MDA TO A CM9760-KBD KEYBOARD

(Refer to Figure 6). Perform this step if you are going to program your CM9760-MDA unit using

the CM9760-KBD keyboard. Connect the serial port of your keyboard to the COM 1 port on the

MDA unit. To do more than one MDA unit, each time you will need to unhook the keyboard from

the MDA unit you just programmed and hook the keyboard to the next MDA unit.

FUSE TYPE: 2AG

1/4A SB

CM9505UPS

COAX CABLE

CM9505UPS

KEYBOARD CARD CAGE

STRAIGHT CABLE

INPU

120VAC

PGM

MON

COM1COM2

UNIT ID

OUTPUT

CM9760-KBD

CM9760-MDA

COM 1

= VIDEO

= DATA

REVERSED CABLE

Figure 6. CM9760-KBD Setup for Direct Control

CONNECTING THE MDA TO A KBD200A OR KBD300A KEYBOARD

A single KBD200A or KBD300A keyboard can be used to program the CM9760-MDA

Master Distribution Amplifier. The keyboard is connected to the COM 1 port of the distribu-

tion amplifier through a KBDKIT (120 VAC) or KBDKIT-X (230 VAC) wall block and a

specially modified keyboard data cable. Connect your monitor as shown in Figure 6.

NOTE: You need two key-

board data cables for this

connection. You must

modify one cable as ex-

plained in Keyboard Wiring

on the next page.

Switch Settings

To set the switches in the keyboard (refer to Figure 7):

1. Remove the two screws and the DIP switch cover plate from the rear of the keyboard.

2. Place switches 5 and 8 in the ON position. This selects the CM9760-MDA mode of

operation.

3. Replace the cover plate.

PIN1

KBD200A RJ-45

JACK PINOUTS

TX+

TX–

12 VAC/DC

NONPOLAR

GND

RX–

RX+

}

PLACE SWITCHES 5 & 8 IN

THE DOWN POSITION

(MDA MODE)

Figure 7. Keyboard Rear Panel

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

Keyboard Wiring

Refer to Figure 8.

1. Use the supplied keyboard data cable to connect the keyboard to the RJ-45 jack on

the wall block.

2. Remove the RJ-45 plug from one end of a second keyboard data cable and strip the

cable jacket back 2 inches (5 cm).

3. Hold up the end of the cable that has the RJ-45 plug still attached and examine the

wire colors going to each pin. (Refer to the “check wire colors” detail in Figure 8.)

Make note of the colors going to pins 7 and 8.

4. Connect the stripped wires to the wall block as follows:

Wire from RJ-45 pin 8 to wall block terminal 1;

Wire from RJ-45 pin 7 to wall block terminal 2;

Cut the unused wires back to the cable jacket.

5. Plug the RJ-45 end of the second (modified) keyboard data cable into the COM1 port

on the master distribution amplifier.

6. Plug the KBDKIT or KBDKIT-X into a suitable outlet.

POWER CONNECTIONS

The MDA’s rear panel contains a three-pronged 120 VAC receptacle. Use the supplied

power cord to connect the MDA to a power source.

NOTE: Always replace

blown fuses with fuses of

the same rating. Failure to

do so could result in serious

damage to the unit.

CHECK WIRE COLORS DETAIL

RJ-45 PLUG

PIN7

COM1

HOLD WITH

LOCKING CLIP

ON BOTTOM

FROM PIN 7

TO WALL BLOCK

TERMINALS

FROM PIN 8

KBD200A

TX–

TX+

12 VAC

KBDKIT OR

KBDKIT-X

25-FOOT KEYBOARD

DATA CABLE

Figure 8. CM9760-MDA Keyboard Wiring

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

PROGRAMMING

TIME AND DATE SETUP

You can apply a single time and date and camera title to each input channel, which will

appear on all four output channels. You can also select whether the channel will display:

•

Time, date, and title

Time and date only

Title only

No added text

In addition, you can select:

•

Time and date format, and set the title to be displayed

Character brightness

On-screen location for time, date, and title

PROGRAMMING METHODS

The MDA unit is password protected and can be programmed by using a CM9760-KBD,

KBD200A, or KBD300A keyboard or by using a PC.

NOTE: The CM9760-MDA

Setup program provides an

interface that supports the

message text feature of the

MDA. (For additional infor-

mation, refer to the Set Mes-

sage Text section of this

manual.) The CM9760-KBD,

KBD200A, and KBD300A

keyboards do not provide an

interface that supports

There are two DIP switches to select the input and output port formats, and one to identify

the MDA unit. See the Communication Ports Setup and Address Setup for Daisy Chaining

sections for information on the DIP switches.

You can program the unit in two ways.

•

The first method uses a CM9760-KBD, KBD200A, or KBD300A keyboard and the pro-

gramming monitor output. See the Programming with a Keyboard section for instructions.

The second method requires a PC running Microsoft^®Windows^®and the CM9760-MDA

Setup program. See the Programming with the CM9760-MDA Setup Program section

for instructions.

message text.

PROGRAMMING WITH A KEYBOARD

The KBD200A uses keys for pan/tilt, while the CM9760-KBD and KBD300A use a joystick.

KEYBOARD KEYS AND JOYSTICK

Use the keyboard and the programming video output to manually program the CM9760-MDA.

Any joystick motion or pan/tilt key activates the Main Menu. Use the joystick or pan/tilt keys

to navigate menus. Use the following keyboard keys to program the MDA.

Open

Near

Use this key to move down through selections in program mode.

Use this key to move up through selections in program mode.

Use this key to quickly exit a menu and return to the Main Menu from

any submenu or to exit program mode without having to select EXIT on

the Main Menu.

Pan/Tilt Controls

The pan/tilt keys or joystick controls the cursor’s position. Moving the

joystick up and down or pressing the up/down keys maneuvers through

the menu selection. Moving the joystick left and right or pressing the

left/right keys positions the cursor horizontally when a menu has more

than one item on a line. Moving the cursor to the right on RETURN on

a menu, or on any item in the Main Menu, selects the item.

Blue Buttons

(Not applicable to the KBD200A/300A keyboards.) The line of blue

buttons directly below the CM9760-KBD keyboard screen corresponds

to the line of icons on the bottom of the screen. To select one of the

icons, press the blue button directly beneath it.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

ENTERING THE PROGRAMMING MODE WITH THE CM9760-KBD

Use the CM9760-KBD keyboard to program the titles, time, date, and setup of the ports.

1. To enter programming mode from the keyboard, you must first enter the setup mode

for the keyboard. Attach a straight power cable from COM 1 on the rear of keyboard to

the power supply. (The LCD displays the keyboard offline message.)

NOTE: You need a pass-

word to enter setup mode

on the CM9760-KBD key-

board. The default, as set

from the factory, is 1234.

2. Set DIP switch 2 (on the underside of the CM9760-KBD) to ON.

3. You are prompted to enter the setup PIN. (The factory default is 1234.) Do so, and the

main setup mode menu appears.

4. Press the blue button beneath the ADV icon. The Advance Setup 1 screen appears.

5. You have to set the KBD in direct mode. To do so, cycle the host type by pressing the

blue buttons below the left and right arrow icons (<= and =>) until the LCD shows

“HOST DIRECT CAM CTRL.”

6. Press the blue button beneath the Step Forward icon (hand that points down) to go to

the next line. Change the baud rate from 4800 to 9600 by pressing the blue button

beneath the right arrow icon.

7. Press the blue button beneath the SAVE icon.

8. Press the blue button beneath the exit icon (an open door).

9. Press the blue button beneath the camera icon.

10. Press the blue button beneath the Step Forward icon (hand pointing down) four times.

11. You need to define a camera. You are currently on physical 0, logical 0. You need to

change the logical to 1.

a. Press the blue button beneath the DEF NUM icon (this reverses videos).

b. Press 1.

c. Press the blue button beneath the DEF NUM icon. Physical 0 should now have a

logical 1.

d. Press the blue button beneath the SAVE icon.

12. Press the blue button beneath the exit icon (an open door) twice.

13. You are prompted to turn off DIP switch 2. Do so.

14. Connect a reversed cable from the power supply to COM 1 on the rear of the MDA.

15. Access the main programming menu by moving the joystick in any direction (see

Figure 9, Main Menu). You can now begin programming.

16. When you finish programming, select EXIT from the Main Menu. Then disconnect the

keyboard to exit programming mode.

ENTERING THE PROGRAMMING MODE WITH THE KBD200A

OR KBD300A KEYBOARD

1. Access the main programming menu by moving the joystick in any direction (KBD300A)

or by pressing any pan/tilt key (KBD200A) (see Figure 9, Main Menu). You can now

begin programming.

2. When you finish programming, select EXIT from the Main Menu. Then disconnect the

keyboard to fully exit the programming mode.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

MAIN MENU

PELCO MDA UNIT 01

SOFTWARE VERSION 2.05

MAIN MENU:

CAMERA TITLE

COMPENSATION

CAMERA DISPLAY

TIME/DATE

PORTS

RESET

EXIT

Figure 9. Main Menu

The fields in the Main Menu (Figure 9) are defined as follows:

PELCO

MDA UNIT

The first line is the title line. It contains the Unit ID as set from the MDA

unit’s rear panel.

NOTE: If you are using a

KBD200A keyboard, use the

appropriate pan/tilt key (up,

down, right, left) in place of

moving the joystick.

SOFTWARE

VERSION

This field shows the version of software being used.

MAIN MENU

This field instructs you to pick an item to set from the six selections

listed or to exit the setup program.

A number precedes each of the seven selections. It flashes when the cursor is positioned

on it. To select an item, move the keyboard’s joystick up or down to position the cursor on

the item you desire, then press the joystick to the right.

Selecting items 1 through 6 will display another menu. When you finish programming,

select EXIT and press the joystick right, or exit by pressing the NEAR key.

SET CAMERA TITLE

If you choose item 1 on the Main Menu, the program displays the following menu:

CAMERA 01

CAMERA TITLE:

LOADING DOCK 4

RETURN

Figure 10. Set Camera Title Menu

Use this menu to enter a camera title. When the program displays this menu, the camera

number flashes on the menu’s top line.

•

If you want to edit the information for the camera number displayed, press the OPEN key.

If you want a different camera, press the joystick to the right to bring up the next camera.

The title already programmed for the selected camera is displayed.

Use the joystick to access the title. Move the joystick left and right to position the cursor

over a character in the title. Use the OPEN/CLOSE key to access a character. Pressing the

joystick right places the cursor on the next character to program.

When you finish programming the title, press the joystick down to move the cursor to RETURN

on the menu and then press the joystick to the right. This returns you to the Main Menu.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

SET CABLE COMPENSATION

If you choose item 2 on the Main Menu, the program displays the following menu:

CABLE COMPENSATION

CAM CMP CAM CMP CAM CMP

RETURN

Figure 11. Set Cable Compensation Menu

Transmitting video signals over long distances can adversely affect video images.

However, compensation can be used to adjust for video signal degradation.

When the system displays the menu, the cursor flashes on the compensation setting for

camera 1.

To change the compensation (CMP) entry, use the joystick to move to the input (1-16) for which

you want to change the compensation. For example, moving the joystick down positions the

cursor at the entry for camera 2. Press the OPEN key to toggle through the settings. The

settings are numbered 1-4. Setting 1 is for no compensation, setting 2 is for a video input that

is 500 feet (152 m) from the CM9760-MDA, setting 3 is for 1,000 feet (304 m), and setting 4 is

for 1,500 feet (457 m).

To exit the menu, position the cursor on the R in RETURN and press the joystick right.

SET CAMERA DISPLAY

If you choose item 3 on the Main Menu, the program displays the following menu:

CAMERA 01 DISPLAY

1. POSITION DISPLAY

BRIGHTNESS:

ENABLE TITLES:

ENABLE TIME DATE:

ENABLE VIDEO DISPLAY

OUTPUT:

ON OFF ON OFF

RETURN

Figure 12. Set Camera Display Menu

This menu contains setup information for how the camera display will look. You can turn the

camera display for each output on or off. You can also adjust and set the characters’

brightness and position. These two settings are universal for all cameras.

When the program displays this menu, the camera number on the top line flashes. Press

the joystick right to select the next camera if you do not want to program output, brightness,

or text position for the current camera. Use the OPEN key to select the three items to be

adjusted on this menu.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

The fields (or items to be set) are defined as follows:

POSITION

DISPLAY

The first item to set is the display position, which is digitally selected

NOTE: At least one output

display must be turned on

and you must use this out-

put on a monitor to see its

position.

and controlled by the keyboard. To move the output display, position

the cursor at item 1. The “1” flashes. Press the joystick right to choose

the item. Press the joystick up/down and left/right to position the

display on the monitor. See Figure 35 for the output display. At least

one output display must be on and you must use this output on a

monitor to see its position. To return to the Camera Display Menu after

setting the position display, press the OPEN or CLOSE key.

BRIGHTNESS

To set brightness, press the joystick down to position the cursor at the

brightness item on the menu. Use the OPEN key to increase

brightness and the CLOSE key to decrease it. Brightness numbers

range from 1 (darkest) to 8 (brightest). Brightness changes on the

menu as you change the number.

ENABLE TITLES You toggle this field on/off by placing the cursor on the selection and

pressing the OPEN key. You can activate or deactivate the titles on a

camera-by-camera basis. The selection immediately appears on the menu.

ENABLE TIME You toggle this field on/off by placing the cursor on the selection and

DATE

pressing the OPEN key. You can activate or deactivate the time and

date on a camera-by-camera basis. The selection immediately appears

on the menu.

ENABLE VIDEO Use this field to direct the alphanumeric data (text) to the desired

DISPLAY

OUTPUT

output. In the example in Figure 12, outputs 1 and 3 will have alpha-

numeric information while outputs 2 and 4 will not. To change the

settings, position the cursor at locations A, B, C, or D and press the

OPEN or CLOSE key to turn the settings ON or OFF.

As shipped from the factory, the four outputs for the title, time, and date display are ON.

Brightness is set to level 5.

Position the cursor at RETURN and press the joystick right to return to the Main Menu. You

can also press the NEAR key to exit this menu.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

SET TIME AND DATE

If you choose item 4 on the Main Menu, the program displays the following menu:

SET TIME/DATE

DATE:

TIME:

STYLE:

TYPE:

DEC-31-02

11:59:52 PM

MMM-DD-YY

12 HOUR

SET CLOCK

Figure 13. Set Time and Date Menu

The CM9760-MDA supports four of the CM9760-CC1’s time and date formats; and the MDA’s

format must match the CC1’s format for correct updating of the MDA from the CC1 to occur. Table

E shows how the supported formats should be matched.

Table E. CM9760-CC1/CM9760-MDA Format Matchup

CM9760-CC1

Format #

CM9760-CC1

Format Example

CM9760-MDA

Format

16/11/03 17:56

DD-MM-YY 24 hour

MM-DD-YY 24 hour

DD-MM-YY 12 hour

MM-DD-YY 12 hour

11/16/03 17:56

16/11/03 05:56 PM

11/16/03 05:56 PM

Press the joystick up/down and left/right to move through the four general selections on the

menu. If you press the joystick right for any selection in the set time or date areas of this menu

without first entering a number, the program keeps the existing information for the field and

moves you to the next field.

The fields are defined as follows:

DATE

When the program displays this menu, the cursor flashes on the month entry in this

field. To change the month entry, press the OPEN or CLOSE key to pick the number

of the month you want. Then press the joystick right to enter your selection. This also

moves you to the next entry (day) on the line.

If you want to leave the month area without changing the month, just press the joystick

right. This moves the cursor to the day area.

Select the day using the OPEN or CLOSE key. Depending on the month, the number

of days will be 28, 29, 30, or 31. To enter your selection, press the joystick right.

After you enter a day, the year flashes. Use the OPEN or CLOSE key to choose a number

between 0 and 99 for the year. Then press the joystick right to enter your selection.

TIME

Select the hour, minute, and second in the same way you selected the month, day,

and year in the previous field.

STYLE The four styles for date display are mm dd yy, dd mm yy, mmm dd yy, and dd mmm yy

where mm = 2-digit month, mmm = 3-letter month abbreviation, dd = 2-digit day, and yy = 2-

digit year. Use the OPEN or CLOSE key to make your selection. Then press the joystick

right to enter your selection. Refer to Table E for formats compatible with the CM9760-CC1.

TYPE

The time types are 12-hour and 24-hour (military time). In 12-hour mode, the program

displays an AM or PM on the monitor. Use the OPEN or CLOSE key to make your

selection. Then press the joystick right to enter your selection.

When you finish entering information, press the joystick down to place the cursor at RETURN on

the menu. Press the joystick right to return to the Main Menu.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

SET PORT

If you choose item 5 on the Main Menu, the program displays the following menu:

SET SERIAL PORT 1

PROTOCOL:

BAUD RATE:

DATA BITS:

STOP BITS:

PARITY:

9760KB

4800

EVEN

RETURN

Figure 14. Set Port Menu

This menu lets you view the settings of the two ports, and change the settings in one of them.

•

The Port 1 menu settings can be changed. The Port 1 menu lets you pick what you

want to connect to Port 1—an ASCII device (such as a PC), a CM9760 keyboard, a

CM9760 CC1, or an MDA loop. You use the menu’s Protocol field to select which one.

You use the remaining four fields (Baud Rate, Data Bits, Stop Bits, and Parity) to set

the communication parameters for what you picked in the Protocol field.

•

The Port 2 menu settings cannot be changed. Port 2 is locked as the MDA loop-out

port. It is set up so you can plug a CM9760-KBD keyboard into it and program the MDA.

When the program displays the menu, the “1” in “Port 1” flashes. (To view the setup for Port

2, press the joystick right.)

To set up Port 1, press the OPEN key. The selection in the Protocol field flashes.

PROTOCOL

Use the OPEN and CLOSE keys to cycle through the four types of

protocol. These are Terminal (ASCII device), CM9760-KBD, CM9760-

CC1, and MDA Loop.

BAUD RATE

•

If you chose Terminal in the Protocol field above, the ASCII

protocol for external devices other than a keyboard or Pelco

system is activated. The available baud rates are 1200, 2400,

4800, and 9600 bits per second. In Terminal mode, you can also

select the data bit length, the number of stop bits, and the parity

type. Place the cursor on the displayed rate and press the OPEN/

CLOSE key to cycle forward and backward through the options.

•

If you chose CM9760-KBD in the Protocol field above, 9600 baud

is displayed but cannot be changed.

If you chose CM9760 CC1, 9600 baud is displayed, which cannot

be changed. This selection is used for connecting to the CM9760

Controller, which provides the timing signal for the MDAs.

(NOTE: The baud rate must equal that which was selected from

the system.)

•

If you chose MDA Loop in the Protocol field above, 9600 baud is

displayed but cannot be changed.

DATA BITS

The number flashes. To select the number of data bits, use the OPEN

or CLOSE key to choose between 7 and 8 bits. Press the joystick

down to move to the next field.

NOTE: The following can

only be adjusted in Terminal

mode.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

STOP BITS

PARITY

The number flashes. Use the OPEN or CLOSE key to choose between

1 and 2 stop bits. Press the joystick down to move to the next field.

The three options for this field are none, odd, and even. The first

character in the word flashes when you access this field. Use the

OPEN or CLOSE key to move through the three selections. When you

leave this field, the program keeps the last selection.

Position the cursor at RETURN and press the joystick right to return to the Main Menu, or

press the NEAR key.

RESET MDA

If you choose item 6 on the Main Menu, the program displays the following menu:

YOU ARE ABOUT TO

RESET THIS UNIT TO

THE ORIGINAL FACTORY

SETTINGS

ARE YOU SURE? NO

Figure 15. Reset CM9760-MDA Screen

This screen lets you reset the CM9760-MDA’s software to the original factory settings. You

can change the selection from “NO” to “YES” on the line that asks “ARE YOU SURE?” by

pressing the OPEN key. The unit returns to the original factory settings for titles, cable

compensation, time, date, and communication ports when you place the cursor on

RETURN and press the joystick right.

Position the cursor at RETURN and press the joystick right to return to the Main Menu, or

press the NEAR key.

PROGRAMMING WITH THE CM9760-MDA SETUP PROGRAM

CM9760-MDA SETUP PROGRAM DESCRIPTION

Using a PC, the CM9760-MDA Setup program allows you to set camera titles, cable

compensation, camera display, time and date, and message text for each video output. The

program is useful when multiple CM9760-MDA units are used in one installation.

SYSTEM REQUIREMENTS

The CM9760-MDA Setup program is provided on the CM9760-MDA Resource CD. System

requirements are as follows:

•

Microsoft Windows 98, 2000, NT, or XP

Intel486^™or Pentium^®processor-based PC

16 MB or more of RAM

25 MB of free hard disk space

CD-ROM drive

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING THE CM9760-MDA SETUP PROGRAM

The following procedure provides instructions to install the CM9760-MDA Setup program

on a PC that meets or exceeds minimum system requirements (see System Requirements

above). (For information about connecting the PC to the CM9760-MDA, see Connecting the

MDA to an External PC earlier in this manual.)

To install the CM9760-MDA Setup program, do the following:

1. Start Microsoft Windows. If Microsoft Windows is already running, close any applica-

tion programs that may be running.

2. Insert the CM9760-MDA Resource CD into the CD-ROM drive.

The CD automatically starts and the CM9760-MDA Setup dialog box appears.

3. Click CM9760-MDA Software.

The Welcome dialog box appears.

4. Click OK.

The CM9760-MDA Setup software installation dialog box appears.

5. Begin CM9760-MDA Setup software installation by doing one of the following:

•

Install CM9760-MDA Setup software into the default destination directory by

clicking the button indicated in the on-screen instructions. The default installation

directory is as follows:

C:\Program Files\CM9760-MDA Setup\

•

If necessary, change the installation destination directory by clicking Change

Directory:

a. Enter or select the destination directory and then click OK.

The CM9760-MDA Setup software installation dialog box reappears.

b. Click the button indicated in the on-screen instructions to install the

CM9760-MDA Setup software.

The CM9760-MDA Setup – Choose Program Group dialog box appears.

6. Do one of the following:

•

Accept the default program group name, CM9760-MDA SETUP, by clicking

Continue.

Enter a new program group name or select a name from the Existing Groups list,

and then click Continue.

A message appears indicating that the CM9760-MDA Setup program was installed

successfully.

7. Click OK.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

STARTING THE CM9760-MDA SETUP PROGRAM

To start the CM9760-MDA Setup program, do the following:

1. In the Windows taskbar, click the Start button, point to Programs > CM9760-MDA

SETUP, and then click CM9760-MDA SETUP.

The CM9760-MDA SETUP introductory screen appears followed by the Login dialog

box shown in Figure 16.

Figure 16. Login Dialog Box

2. Enter the password and then click OK. The default password is 2899100. (To set a

new password, refer to the Set Password section later in this manual.)

The CM9760-MDA SETUP dialog box appears as shown in Figure 17.

Figure 17. CM9760-MDA SETUP Dialog Box

For information about the CM9760-MDA SETUP dialog box, see the following section titled

CM9760-MDA SETUP Dialog Box.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

CM9760-MDA SETUP DIALOG BOX

The CM9760-MDA SETUP dialog box, Figure 17, is the main window of the CM9760-MDA

Setup program. Menus at the top of the dialog box let you access other menus and operation

windows. The following sections provide detailed information about the functions that can

be performed using the CM9760-MDA SETUP dialog box:

•

The Set Password section tells you how to change the current password used to enter

the CM9760-MDA Setup program.

•

The Set Unit ID section describes how to select the unit you want.

The Set System section deals with the setup of the communication parameters for the

CM9760-MDA Setup program and the CM9760-MDA unit and with the reset of MDA

software.

•

The Set Time and Date, Set Unit ID, Set Titles, Set Cable Compensation, Set Display,

and Set Message Text sections deal with the setup of the data to be used by the

CM9760-MDA and the CM9760-MDA Setup program.

The Send Data section describes how to send time and date, titles, or both.

SET PASSWORD

To change the password used to enter the CM9760-MDA Setup program, click Edit and

then click Password on the CM9760-MDA SETUP dialog box. As shown in Figure 18, a

dialog box appears asking you to enter the old (current) password.

Figure 18. Old Password Dialog Box

Enter the current password, and then click OK.

As shown in Figure 19, another dialog box appears asking you to enter a new password

and to verify the new password by entering it a second time.

Figure 19. New Password Dialog Box

After entering and verifying your new password, click the Change button to load your new

password. If you decide not to change your password, click the Cancel button.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

SET UNIT ID

To enter the MDA unit for which you want to assign or modify settings, click Edit on the

CM9760-MDA SETUP dialog box and then click Unit ID. The Unit ID dialog box, Figure 20,

appears.

Figure 20. Unit ID Dialog Box

Enter the Unit ID number (1-64), and then click OK.

CAUTION:

Be careful

when changing

SET SYSTEM

The System menu allows you to set up communication ports for the CM9760-MDA and the

PC and to reset MDA software to factory default settings.

the selections on the

CM9760-MDA ports. You

could accidentally change

the port setting and lose

communication with your

system!

CM9760-MDA Communication: To set up the communication port for the

CM9760-MDA unit, click System on the CM9760-MDA SETUP dialog box and then click

MDA COM1 Setup. The MDA COM 1 Setup dialog box, Figure 21, appears.

Figure 21. MDA COM 1 Setup Dialog Box

Set communication parameters for the COM 1 port of the CM9760-MDA as follows:

NOTE: The baud rate and

parity settings of the con-

nected CM9760-MDA

COM 1 port and PC port

must match.

1. Select the baud rate by clicking the option button next to the desired setting. The

default is 9600.

2. Select the parity by clicking the option button next to the desired setting. The default is

Even.

3. Enter the unit ID number of the MDA to which you are sending the data. The unit ID

number ranges from 1 to 64. The default is 1.

4. Click OK.

A Warning dialog box appears indicating that the CM9760-MDA COM 1 port settings

will be changed and that the PC serial port settings will be updated accordingly.

5. Click OK.

A confirmation dialog box appears indicating that the MDA COM 1 port settings were

changed.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Click OK. The MDA COM 1 Setup dialog box remains on the screen displaying the

updated port settings.

NOTE: Clicking Cancel on

the MDA COM 1 Setup

dialog box does not cancel

the MDA COM 1 port setting

changes you made. Clicking

Cancel only closes the

dialog box.

7. Test the CM9760-MDA communication port by clicking Test Comm:

•

If communication between the MDA COM 1 port and the PC port has been

established, an information dialog box appears confirming communication

between the ports. Click OK on the information dialog box, and then click Cancel

on the MDA COM 1 Setup dialog box to close the dialog box.

•

If communication between the MDA COM 1 port and the PC port has not been

established, a No Response dialog box appears instructing you to check the PC

port and unit ID settings. Click OK. Modify the settings as necessary and then

test the CM9760-MDA port again to confirm communication.

PC Communication: To set up the communication port for the PC, click System on the

CM9760-MDA SETUP dialog box and then click PC COM Setup. The System Communica-

tion Setup dialog box, Figure 22, appears.

Figure 22. System Communication Setup Dialog Box

Set communication parameters for the PC as follows:

1. Select the PC serial port by clicking the option button next to the desired setting. The

System Communication Setup dialog box displays up to four serial ports—COM 1,

COM 2, COM 3, and COM 4—depending on the number of serial ports available on

your PC. Only serial ports COM 1 and COM 2 are displayed in Figure 22. The default

is COM 1.

2. Select the baud rate by clicking the option button next to the desired setting. The

default is 9600.

NOTE: The baud rate and

parity settings of the con-

nected CM9760-MDA

COM 1 port and PC port

must match.

3. Select the parity by clicking the option button next to the desired setting. The default is

Even.

4. For port-powered RS-232 to RS-422 converters, set RTS (Request To Send) high by

selecting the Hold RTS High item. The Hold RTS High item is selected when a

checkmark appears in the checkbox next to the item. Clicking the checkbox functions

as a toggle and selects or deselects the Hold RTS High item.

5. Click OK.

MDA Software Reset: To reset MDA software to factory default settings, click System

on the CM9760-MDA SETUP dialog box and then click MDA Software Reset. At the prompt

that asks you whether you wish to reset MDA software, click Yes.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

SET TIME AND DATE

To set time and date, you send the current time and date from your PC or edit the time and

date and upload it. To get the current time and date from your PC, click Edit on the

CM9760-MDA SETUP dialog box and then click Time & Date. The Set Time and Date

dialog box, Figure 23, appears. The dialog box contains the current time and date of your

PC.

Figure 23. Set Time and Date Dialog Box

The Set Time and Date dialog box allows you to do the following:

•

Set the date:

– Set the month by clicking the down arrow button and then clicking the desired month

from the drop-down box.

– Set the day and year by selecting the desired setting in the list boxes using the up or

down button.

•

Set the time—hour, minute, and second—by selecting the desired setting in the list

boxes using the up or down button.

Set the time format to either 12-hour or 24-hour format by clicking the option button

next to the desired setting.

Set the date display style to one of the following options: dd/mm/yy, mm/dd/yy,

dd/mmm/yy, or mmm/dd/yy where dd = 2-digit day, mm = 2-digit month, yy = 2-digit

year, and mmm = 3-letter month abbreviation. To set the date style, click the option

button next to the desired setting.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

Note that the date style and time format used by the CM9760-MDA must match those used

by the CM9760-CC1. Refer to Table F for date styles and time formats compatible with the

CM9760-CC1.

Table F. CM9760-CC1/CM9760-MDA Compatible Date Styles and Time Formats

CM9760-CC1

Date Style/

Time Format #

CM9760-CC1

Date Style/

Time Format Example

CM9760-MDA

Date Style/

Time Format

16/11/03 17:56

DD-MM-YY 24 hour

MM-DD-YY 24 hour

DD-MM-YY 12 hour

MM-DD-YY 12 hour

11/16/03 17:56

16/11/03 05:56 PM

11/16/03 05:56 PM

Click the Send button to upload your settings to the CM9760-MDA unit. To exit the dialog

box without uploading your settings, click Cancel.

SET TITLES

NOTE: A list of characters

supported by the MDA for

display of titles is provided in

Appendix B.

As shown in Figure 24, you set titles in the CM9760-MDA SETUP dialog box. Using the

CM9760-MDA Setup program, you can read the titles if they are already loaded in the

CM9760-MDA or create titles and upload (send) them to the CM9760-MDA.

Figure 24. Setting Titles Using the CM9760-MDA SETUP Dialog Box

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

To Download Titles From An MDA: To import titles from a CM9760-MDA unit, click File on

the CM9760-MDA SETUP dialog box and then click Import. The program asks you to confirm

the ID number of the MDA unit from which the titles will be loaded. (Click Yes if this is the unit from

which you want to import titles. If not, click No. Then click Edit, click Unit ID, change the unit ID to

the one you want, and return to the CM9760-MDA SETUP dialog box.)After you confirm, the

program reads the titles in the CM9760-MDA unit and displays them in the CM9760-MDA

SETUP dialog box.

To Load Default Titles: To load all 16 fields with “CAMX” (where “X” is a camera

number), click the Load Defaults button near the bottom of the CM9760-MDA SETUP

dialog box. The defaults can be used to test communications with the CM9760-MDA unit.

Or, you can modify the defaults by highlighting and typing over them.

To Edit Titles: Once you have imported titles from a CM9760-MDA unit into the

CM9760-MDA SETUP dialog box or loaded default titles, you can edit them. You can then

send the titles back into the CM9760-MDA unit, and store them as a file in your PC. To edit a

title in the dialog box, use the cursor to highlight the line (or characters) you want to change

and type over it. Or you can simply edit titles using the normal editing keys (backspace, arrows,

DELETE, and space bar).

To Upload Titles: You can upload (send) the edited titles that are in the CM9760-MDA

SETUP dialog box back into the CM9760-MDA unit. Click Send at the top of the dialog box,

and then click Titles. The program asks you to confirm the MDA unit that will receive the

titles. If the ID is correct, click the Yes button. If it is not the MDA unit you want to receive

the edited titles: click NO, click Edit at the top of the dialog box, click Unit ID, change the

unit ID, and return to the CM9760-MDA SETUP dialog box.

Another way to transmit this data to the CM9760-MDA unit is to click the Send Titles button

at the bottom of the CM9760-MDA SETUP dialog box.

To Save Titles: To save the titles displayed in the CM9760-MDA SETUP dialog box to

your PC, click File and then click Save or Save As. The titles are saved in a subdirectory

called “Camera Titles.”

To Print Titles: To print titles, click File on the CM9760-MDA SETUP dialog box and

then select Print. Click Current Title to print the titles currently in the window or click From

File to print titles stored in a file on your PC.

To Clear Titles: To erase all the titles from the CM9760-MDA SETUP dialog box at one

time, click the Clear Titles button.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

SET CABLE COMPENSATION

The CM9760-MDA contains circuitry to adjust for long cable runs between the camera and

the CM9760-MDA.

To set the cable compensation for each camera using the CM9760-MDA Setup program,

click Edit on the CM9760-MDA SETUP dialog box and then click Cable Compensation. The

Cable Compensation dialog box, Figure 25, appears.

Figure 25. Set Cable Compensation Dialog Box

To set cable compensation for a camera, do the following:

1. Enter the Unit ID number (1-64) of the MDA unit to which the camera is connected,

and then press Return. Note that all subsequent changes that are made using the

CM9760-MDA Setup program will be applied to the unit ID number that was entered.

2. Enter the channel (camera) number (1-16) for which you want to set cable compensa-

tion, and then press Return. All subsequent changes that are made using the

CM9760-MDA Setup program will be applied to the channel number that was entered.

3. If you wish the cable compensation of the channel number entered in step 2 above to

be applied also to all of the other 15 channels, select the Global checkbox option.

4. Set cable compensation by clicking the option button next to the setting that is closest

to the actual length of the cable connecting the camera to the MDA: 500 feet (152 m),

1,000 feet (304 m), or 1,500 feet (457 m). The program illustrates your selection by

displaying 500-foot (152 m) reels of cable at the bottom of the dialog box.

If cable compensation is not required, select 0 feet (default setting).

When you finish entering all the data for the compensations you want for your system,

close the dialog box by clicking the “X” box.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

SET DISPLAY

The Display dialog box allows you to set the positions of the alphanumeric display (text

location) for each camera input. In addition, you can adjust brightness through eight levels.

You can also pick—for each camera input—what each of the four outputs associated with the

input video will have for a display; that is, the alphanumeric display is ON or OFF for each of the

four outputs.

To access the Display dialog box, click Edit on the CM9760-MDA SETUP dialog box and

then click Display.

Figure 26. Display Dialog Box

At the top of the Display dialog box, you can set the unit ID and channel (camera) number.

To set the unit ID, enter the unit ID number (1-64) and then press Return. To set the

channel, enter the channel number (1-16) and then press Return. In addition, there is a

Global option for title position, brightness, output on/off, and input on/off that allows all

cameras of a unit to be set to the same state as the current channel. Also, there are five

options: (display) Off, Position Text, Adjust Brightness, Output On/Off, and Input On/Off.

The options are defined as follows:

NOTE: Selecting both the

Off option and the Global

option causes all display

settings for the current

channel to be applied to all

of the other 15 channels.

Off

This option turns the setup display off for the program.

Position Text

This option sets the position of text; that is, where text will appear on

all video outputs for the cameras selected that have the display option

ON. To position text on an NTSC video display, click the NTSC option

button (default setting). To position text on a PAL video display, click

the PAL option button. Use the up arrow, down arrow, left arrow, and

right arrow buttons to position the text on the video outputs. See

Figure 27, Position Text Dialog Box. As adjustments are made, they

appear in the blue screen at the bottom of the dialog box.

NOTE: If message text is

set, the Position Text dialog

box may indicate the posi-

tion of message text rather

than title/time/date text. For

information about message

text, refer to the Set Mes-

sage Text section of this

manual.

Adjust

Brightness

The brightness level option for the text display ranges from 1 (darkest)

to 8 (brightest). Use the up arrow and down arrow buttons to adjust

brightness. See Figure 28, Adjust Brightness Dialog Box. As adjust-

ments are made, they appear in the blue screen at the bottom of the

dialog box.

Output On/Off

Input On/Off

For each camera input, this option determines the output(s) (Out 1,

Out 2, Out 3, Out 4) that will have an alphanumeric (text) display. A

check-mark in the box turns on the output. See Figure 29, Output

On/Off Dialog Box.

This option gives you two selection boxes in which you can toggle

time/date and titles on and off. A checkmark in the box turns on the

selection. See Figure 30, Input On/Off Dialog Box.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 28. Adjust Brightness Dialog Box

Figure 27. Position Text Dialog Box

Figure 30. Input On/Off Dialog Box

Figure 29. Output On/Off Dialog Box

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

SET MESSAGE TEXT

The CM9760-MDA accepts message text to meet the needs of applications that require

real-time information overlaid on the video being viewed. Up to five lines of message text

can be sent to the MDA simultaneously. Each line can contain up to 24 alphanumeric

characters. The message text can be inserted onto any MDA channel independently.

NOTE: A list of characters

supported by the MDA for

display of message text is

provided in Appendix B.

The CM9760-MDA Setup program provides a tool that demonstrates support of the

message text feature of the MDA. The program allows message text to be sent from the PC

to an MDA or to an MDA daisy chain. The PC application is designed as an example of

message text operation for third parties who wish to develop their own message text

interface to the MDA. (Refer to the Applications section of this manual for an application

diagram and to Appendix C for a listing of the message text insertion commands supported

by the MDA.)

To set message text using the CM9760-MDA Setup program, proceed as follows:

1. Open the Position Text dialog box and do the following:

a. Position the title/time/date text in the top or middle of the screen (the text should

not be positioned at the bottom of the screen).

NOTE: Positioning the title/

time/date text in the top or

middle of the screen in the

Position Text dialog box

ensures that you will be able

to view the message text

that is displayed on a moni-

tor. (For information about

the Position Text dialog box,

refer to the Set Display

b. Close the Position Text dialog box.

2. Open the Message Text Editing dialog box by clicking Edit on the CM9760-MDA

SETUP dialog box and then clicking Message Text. The Message Text Editing dialog

box, Figure 31, appears.

section of this manual.)

Figure 31. Message Text Editing Dialog Box

3. Enter the Unit ID number (1-64) of the MDA unit for which you want to set message

text, and then press Return. Note that all subsequent changes using the

CM9760-MDA Setup program will be applied to the unit ID number that was entered.

4. Enter the channel (camera) number (1-16) for which you want to set message text,

and then press Return. Note that all subsequent changes using the CM9760-MDA

Setup program will be applied to the channel number that was entered.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Determine whether you wish to apply message formatting changes to all channels.

(Changes to message formatting involve programming the Format, Rows to Display,

Rows of Separation, and Display Time settings that are provided in the lower right-

hand corner of the Message Text Editing dialog box. Information about setting

message formatting is provided in step 7 below.)

To apply message formatting changes to all channels, select the Global checkbox

option.

6. Determine whether you wish to display the command transactions between the MDA

and the PC in hexadecimal and ASCII formats. (For additional information about the

command transactions that are displayed, refer to the Showing Commands section

later in this manual.)

To display the command transactions, do the following:

a. Select the Show Commands checkbox. The Command Data window, Figure 32,

appears in front of the Message Text Editing dialog box.

Figure 32. Command Data Window

b. Do either of the following:

•

Move the Message Text Editing dialog box in front of the Command Data

window by clicking the Message Text Editing dialog box. Each time a

command is sent from the PC to the MDA, the Command Data window

appears. After viewing the command transactions, move the Message Text

Editing dialog box in front of the Command Data window again.

•

Minimize the Command Data window. Whenever you wish to view a

command transaction in the Command Data window, click the Command

Data button in the taskbar on the Windows desktop. Then minimize the

Command Data window again.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Set the message text format characteristics in the lower right-hand corner of the

Message Text Editing dialog box by programming the following information:

•

Format—Specifies the positioning of title/time/date text and message text. Select

the desired setting in the list box using the up or down button:

–

Titles on Top specifies that title/time/date text is to be positioned above

message text (default setting).

Messages on Top specifies that message text is to be positioned above title/

time/date text.

•

Rows to Display—Specifies the number of rows (lines) of message text to be

displayed. In addition, the Rows to Display field also specifies the number of

rows of text that can be scrolled (for information about scrolling text, refer to the

Scrolling Message Text section later in this manual). Select the desired setting in

the list box using the up or down button. The range is 0-5 rows. The default

setting is 0, which disables the message text feature.

•

Rows of Separation—Specifies the number of blank rows to be set between the

title/time/date text and the message text displays. Select the desired setting in

the list box using the up or down button. The range is 0-28 rows. The default

setting is 0.

Display Time—Specifies the number of seconds that message text is to be

displayed. Enter a value ranging from 0-9999 seconds. The default setting is 0,

which allows the message text to be displayed for an indefinite period of time or

until the message text is overwritten.

8. Send the formatting changes set in step 7 above to the selected unit and channel(s)

by clicking the Send Current Formatting button, which is located below the Sample

Display screen.

The Sample Display screen then displays the current formatting determined by the

Format, Rows to Display, and Rows of Separation settings selected in step 7. In

addition, the default message text for each row to be displayed appears. The default

message text for rows 1-5 is as follows: Row 1 Message, Row 2 Message, Row 3

Message, Row 4 Message, and Row 5 Message.

Figure 33 provides an example of a Sample Display screen and the associated

formatting settings (titles on top, three rows to display, and two rows of separation).

Note that the Sample Display does not show the actual position of the title/time/date

and message text on the monitor on which the text is to be displayed but rather shows

the position of the title/time/date text in relation to the message text. The actual

positioning of the text is shown in the Position Text dialog box:

•

If message text is set and Titles on Top is set as the format, the Position Text

dialog box shows the positioning of the title/time/date text.

If message text is set and Messages on Top is set as the format, the Position

Text dialog box shows the positioning of the message text.

(For additional information about the Position Text dialog box, refer to the Set Display

section of this manual.)

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 33. Sample Display Screen Example

9. Enter and send message text to the selected unit and channel for the desired number

of rows (as determined by the Rows to Display value set in step 7 above). For each

row, the message text can contain a maximum number of 24 alphanumeric characters.

•

If the desired number of rows is 1, enter the message text into the Row 1

message text entry box and then click the Send Row 1 button.

If the desired number of rows is more than one, you can enter and send the

message text for each row individually or you can enter the message text for all

rows and then send the message text for all rows at one time:

–

To send the message text individually for each row, click the Send Row x

button (x = 1, 2, 3, 4, or 5) as appropriate.

To send the message text for all rows at one time, click the Send Messages

button.

The desired message text is displayed on the number of rows selected to display

message text on the current MDA channel.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

The following sections provide additional information about functions that can be performed

from the Message Text Editing dialog box.

Showing Commands: You can display command transactions between the PC and the

MDA by selecting the Show Commands checkbox in the Message Text Editing dialog box.

The Command Data window displays the command sent to the MDA and the response sent

from the MDA each time you click a command button in the Message Text Editing dialog

box. The command transaction is displayed in hexadecimal format and in ASCII format.

Figure 34 provides a sample of a Command Data window. The message Hello World was

sent from the PC to the MDA using the Send Row 1 command button.

Figure 34. Sample Command Data Window

Note the following:

•

The ASCII equivalent of hexadecimal data 00 to 1F and hexadecimal data 80 and

beyond is represented as dots.

When the MDA acknowledges the command that was sent to it, the MDA responds by

sending A2 as shown in Figure 34. If the MDA does not acknowledge the command

that was sent to it, the MDA responds by sending AA.

For additional information about message text commands, refer to Appendix C in this

manual.

Scrolling Message Text: If you have set message text on a selected unit and channel for

a specified number of rows, the MDA allows you to scroll message text to allow a new

message to be displayed.

To scroll message text, do the following:

1. In the Rows to Display formatting list box, specify the number of text rows that can be

scrolled and displayed.

2. Send the formatting to the selected unit and channel(s) by clicking the Send Current

Formatting button.

3. In the Scroll Text entry box, enter the desired message text and then click the Scroll

Text button.

Message text scrolls as follows. Each row that is scrolled moves upward one row. As a

result, the first row of message text is overwritten. The new message is displayed in the

bottom row, which is determined by the number of rows specified in the Rows to Display

formatting setting.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

An example of message text scrolling is as follows. If the Rows to Display field specifies

that three rows can be scrolled, the following occurs when message text is scrolled:

•

Message text on row 2 moves up to row 1. The message text that previously appeared

on row 1 is overwritten.

•

Message text on row 3 moves up to row 2.

The new message to be displayed (scroll message) appears on message row 3.

Note that you can view the scrolled text in the message text entry boxes by clicking the Get

Messages button.

Loading Default Message Text: You can display the default message text in the message

text entry boxes by clicking the Load Default Messages button. Default message text

appears as follows:

Row 1 Message

Row 2 Message

Row 3 Message

Row 4 Message

Row 5 Message

Scroll Message

Clearing Message Text: For the selected unit and channel, you can clear message text

from a particular row or from all rows. In addition, you can clear message text from all rows

for all channels of a selected unit.

•

To clear message text from a particular row for the selected unit and channel, select

the desired row number in the Clear Row list box using the up or down button and

then click the Clear Row button.

•

To clear message text for all rows (1-5) for the selected unit and channel, click the

Clear All Rows button.

To clear message text for all rows (1-5) for all channels of the selected unit, click the

Clear All Channels button.

Retrieving Current Message Text: If the current message text is not displayed in the

message text entry boxes for the selected unit and channel, you can retrieve the current

message text by clicking the Get Messages button.

Loading Default Format: You can load default format settings of the Format, Rows To

Display, Rows of Separation, and Display Time fields by clicking the Load Default Format

button. The following default settings are displayed:

•

In the Format list box, Titles on Top is displayed and is highlighted. Titles on Top

specifies that title/time/date text is to appear above message text.

In the Rows to Display list box, 0 is displayed and is highlighted. The value of 0

disables the display of message text.

In the Rows of Separation list box, 0 is displayed and is highlighted. The value of 0

prevents the two text displays, date/time/title text and message text, from being

separated by blank rows.

•

In the Display Time text entry box, 0 is displayed. The value of 0 allows the message

text to be displayed for an indefinite period of time or until it is overwritten.

Retrieving Current Formatting: If the current formatting settings are not displayed in the

Sample Display screen and are not shown in the Format, Rows To Display, Rows of

Separation, and Display Time fields, you can retrieve the current settings by clicking the

Get Current Formatting button. The Sample Display screen then displays the current

formatting and the current settings are shown in the formatting fields.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

SEND DATA

The program’s Send menu lets you transmit either the current time and date, titles, or both

to the CM9760-MDA. (You can also use the Send Titles button on the CM9760-MDA

SETUP dialog box to directly send just titles.)

To send data, click Send on the CM9760-MDA SETUP dialog box and then click Time &

Date, Titles, or All.

VIDEO ALPHANUMERIC OVERLAYS

Figure 35, Typical Camera Display With Alphanumerics, shows what is displayed on each

video output. The system displays the title on the first line. The second line shows the time

and date. Depending on the time and date format, there can be extra characters for AM and

PM for the 12-hour format, and two digits instead of the three letters in the month, as

shown in Figure 35.

NOTE: The optional

message text feature of the

MDA allows the MDA to

accept text messages from

third-party equipment.

PROGRAMMED TITLE

ABCDEFGHIJKLMNOPQRST

12-DEC-96 23:59:59

Consequently, text

TIME AND DATE

messages can also appear

on the camera display. (For

additional information, refer

to the Set Message Text

section of this manual.

Figure 35. Typical Camera Display With Alphanumerics

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Symptom

Possible Problem

Possible Solution

Unit not functioning.

No power at the unit.

Check the power plug and

fuse. (Refer to Figure 2 for

fuse location.)

No video source.

Check that the video source

is connected. (Refer to

Figure 1.)

No output device (such as

a monitor).

Check the connection. Check

that the monitor is turned

on. (Refer to Figure 1.)

No video on any output

channel.

No video source.

Check that the video source

is plugged in and function-

ing. (Refer to Figure 1.)

Programming menu not

turning on.

No input from keyboard.

Check that keyboard is

plugged into COM 1. (Refer

to Figure 1.)

No signal from keyboard.

Move joystick right.

Wrong signal from

keyboard.

Place keyboard into direct

mode. (Refer to the Entering

Program Mode section.)

Set keyboard to 4800 baud.

(Refer to the Set Port

section.)

No text overlay on the

video output(s).

Text overlay turned off for

one or all outputs.

Check menu for display

options for that camera.

(Refer to the Set Camera

Display section or Set

Display section, depending

on programming method.)

In addition, check unit ID

DIP switch settings. (Refer

to the Clearing Text Display

on All Channels section.)

Display is set off the

screen.

Check display position in

camera menu. (Refer to the

Set Camera Display section

or Set Display section,

depending on programming

method.)

MDA does not display

a character that was

sent to it.

A character was entered

that is not supported by

the MDA.

Refer to Appendix B for a

list of characters supported

by the MDA for display of

titles and message text.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

Electrical

Consumption:

Fuse:

25 W

120 VAC, 250 mA; 230 VAC, 125 mA

Input Voltage

CM9760-MDA:

CM9760-MDA-X:

120 VAC, 60 Hz ± 10%

230 VAC, 50 Hz ± 10%

Mechanical

Connectors

Video Input:

Video Output:

BNC (16)

BNC (4 per input)

Communications

COM 1 (In):

COM 2 (Out):

RJ-45 8-pin modular

Video

Video Input(s):

Video Output(s):

.5 to 2 Vp-p, 16 inputs per unit

1 Vp-p, 4 outputs per input

Input/Output Impedance: 75 ohms, terminated

Gain:

Unity ±1 dB

Input Cable

Compensation Range: 0-1,500 feet (none, 500, 1,000, 1,500 ft) (none, 152, 304, 457 m)

Frequency Response:

Bandwidth:

Crosstalk:

±1 dB @ 8 MHz

±3 dB @ 15 MHz

-60 dB @ 2.58 MHz

Gain:

+.88 dB

+.55 dB with 1,500 feet of RG59\U

Differential Gain:

Differential Phase:

Max. Output Level:

Signal-to-Noise Ratio:

Tilt:

Less than 4%

Less than 1 degree

1.0 Vp-p terminated

-45 dB

Less than 1 degree

Ground isolated

Inputs:

On-Screen Display

Character Size:

Brightness:

7 x 9 TV lines

Individually adjustable (digital)

Horizontal Position:

Vertical Position:

Communication

Type:

Selectable: RS-232, RS-422, RS-485

Data Rate:

Selectable: 1200, 2400, 4800 or 9600 baud

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

General

Construction:

Dimensions:

Mounting:

Aluminum

See Figure 36

19-in. (48.26 cm) EIA standard rack mount (3 RUs)

Operating Temperature: 14° to 122°F (-10° to 50°C)

Humidity:

90% non-condensing

Lithium battery

Memory Backup:

Ratings

NEMA 1

(Design and product specifications subject to change without notice.)

INPUT

120VAC

PGM

MON

5.25

(13.21)

REAR

VIEW

COM1COM2

UNIT ID

OUTPUT

17.40 (44.20)

18.97 (48.18)

5.25

(13.21)

SIDE

VIEW

12.90 (32.77)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES

Figure 36. CM9760-MDA Dimension Drawing

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX A – APPLICATIONS

The MDA can be used in several different applications. Note that, as illustrated in some of

the applications below, a maximum of 16 MDAs can be daisy-chained. When more than 16

MDAs are required, a CM9760-CDU-T must be used.

•

Figure 37 illustrates a simple system configuration of the MDA.

Figure 38 illustrates a master MDA unit, MDA 1, connected to 63 MDA slave units:

MDA 2 to MDA 64. The slave units accept the master time and date from MDA 1,

which functions as the master clock. (An MDA functions as the master clock when unit

ID DIP switch 8 is set to the ON position. An MDA functions in slave mode when unit

ID DIP switch 8 is in the OFF position, which is the default setting.)

As illustrated in Figure 38, the CM9760-CDU-T must be used when an MDA functions

as the master clock time and date generator for more than 16 MDAs. In the illustration,

note the following:

–

The RS-422 COM 1 port of the master MDA unit (MDA 1) connects to the RS-422

IN data port of the CM9760-CDU-T.

The first RS-422 output of the CDU-T connects to the RS-422 COM 1 port of the

first MDA in a chain of 16 MDAs (MDA 2 to MDA 17).

The second output of the CDU-T connects to the second chain of 16 MDAs

(MDA 18 to MDA 33).

The third output of the CDU-T connects to the third chain of 16 MDAs (MDA 34 to

MDA 49).

The fourth output of the CDU-T connects to a chain of 15 MDAs (MDA 50 to

MDA 64).

In addition, note that RS-422 shielded twisted pair cable is used to connect each

output of the CDU-T to a wall block for connection to the COM 1 port of the first MDA

in each chain.

•

Figure 39 illustrates a PC connected to a chain of 16 MDA units (MDA 1 to MDA 16).

In this application, the PC is used to program the 16 MDA units.

Figure 40 illustrates a PC connected to 64 MDA units: MDA 1 to MDA 64. In this

application, the PC is used to program the 64 MDA units. The Pelco PV130

RS-232/422 converter provides an electrical interface between RS-232 and RS-422

data ports. In Figure 40, the PV130 interfaces the DB9 RS-232 port of the PC to a wall

block for connection to the RS-422 IN port of the CM9760-CDU-T. (Note that the

PV130 RS-232/422 converter eliminates the need to change the internal DIP switch

settings of the MDA COM port to RS-232 for communication with the PC.) A plug-in

power supply allows the PV130 to communicate serial port data over wire pairs for

distances up to 4,000 feet (1,219 m) on the RS-422 side.

Each of the first four outputs of the CDU-T connects to a chain of 16 MDAs (MDA 1 to

MDA 16, MDA 17 to MDA 32, MDA 33 to MDA 48, and MDA 49 to MDA 64).

•

Figure 41 illustrates a CM9760-CC1 connected to a chain of 16 MDA units (MDA 1 to

MDA 16). An RS-422 output of the CC1 connects to the RS-422 COM 1 port of the first

MDA in the chain. MDA 1 to MDA 16 accept the master time and date from the

CM9760-CC1; therefore, the MDAs must be set to slave mode.

Figure 42 illustrates a CM9760-CC1 connected to 64 MDA units: MDA 1 to MDA 64.

An RS-422 output of the CC1 connects to the RS-422 IN data port of the CM9760-

CDU-T. Each of the first four outputs of the CDU-T connects to a chain of 16 MDAs

(MDA 1 to MDA 16, MDA 17 to MDA 32, MDA 33 to MDA 48, and MDA 49 to MDA 64).

MDA 1 to MDA 64 accept the master time and date from the CM9760-CC1; therefore,

the MDAs must be set to slave mode.

•

Figure 43 illustrates an MDA connected to multiplexers.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE: As illustrated in

Figures 45 and 46, the MDA

can be used with Coaxitron

products such as the

•

Figure 44 illustrates a non-Coaxitron setup that includes an MDA connected to a 9760

keyboard, CM9760-CC1 CPU, and CM9760-MXB matrix bay. The MDA accepts the

master time and date from the CM9760-CC1; therefore, the MDA must be set to slave

mode.

CM9760-CXTA, CM6800,

and CM6700. Note that the

MDA must be placed after

the Coaxitron equipment. If

the MDA is placed incor-

rectly, camera control may

be adversely affected.

•

Figure 45 illustrates a Coaxitron setup that includes a System 9760 connected to an

MDA. The MDA accepts the master time and date from the CM9760-CC1; therefore,

the MDA must be set to slave mode.

Figure 46 illustrates a CM6800 connected to an MDA. The MDA accepts the master

time and date from the CM6800; therefore, the MDA must be set to slave mode. (The

MDA can also accept the master time and date from the CM6700.)

Figure 47 illustrates an MDA that accepts message text from third-party equipment.

The third-party equipment connects to a COM port (COM 1 or COM 2) of the MDA

using the RS-232 or RS-422 communication standard. For cabling requirements, refer

to the Data Connections section of this manual. For information about COM port DIP

switch settings required for RS-232 and RS-422 communication, refer to the Commu-

nication Ports Setup section of this manual. For a wiring diagram of the MDA using

RS-232 communication, refer to the Connecting the MDA to an External PC section of

this manual. For information about MDA COM port pinouts using RS-422 communica-

tion, refer to Table D in this manual. Note that when connecting the MDA to third-party

equipment using RS-422 communication, TX+ must connect to RX+ and TX- must

connect to RX-. For information about support of message text insertion by the MDA,

refer to the Set Message Text section of this manual and to Appendix C.

CAMERA

CAMERA INPUT

INPUT

120VAC

PGM

MON

COM1COM2

UNIT ID

OUTPUT

PELCO CM9760-MDA

MONITOR

VCR

Figure 37. Simple System Configuration

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

CM9760-MDA1

INPUT

120VAC

PGM

MON

COM1COM2

UNIT ID

OUTPUT

RS-422 REVERSED CABLE

CM9760-CDU-T

100-240V

Tx+

Tx-

GND

OUT

10-24 ACDC

RS-422

SHIELDED

TWISTED

PAIR*

MDA 2

MDA 18

MDA 34

MDA 50

RS-422

120VAC

PGM

MON

PGM

MON

PGM

MON

PGM

MON

REVERSED

CABLE

COM1COM2

UNIT ID

MDA 3

MDA 19

MDA 35

MDA 51

RS-422

120VAC

PGM

MON

PGM

MON

PGM

MON

PGM

MON

REVERSED

CABLE

COM1COM2

UNIT ID

MDA 4

MDA 20

MDA 36

MDA 52

120VAC

RS-422

120VAC

PGM

MON

PGM

MON

PGM

MON

PGM

MON

REVERSED

CABLE

COM1COM2

UNIT ID

MDA 17

MDA 33

MDA 49

MDA 64

RS-422

120VAC

PGM

MON

PGM

MON

PGM

MON

PGM

MON

REVERSED

CABLE

COM1COM2

UNIT ID

*BELDEN 9843 OR SIMILARCABLE

Figure 38. Master MDA Time and Date Generator for 63 MDA Slave Units (64 Total MDA Units)

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

PelcoVisionVS7108

-Visual Switcher

Pelco 1996

INPU

120VAC

PGM

MON

Start

PelcoVisionVS7108

8.07 AM

CM9760-MDA

COM1COM2

UNIT ID

OUTPUT

RS-232*

INPU

120VAC

PGM

MON

CM9760-MDA

COM1COM2

OUTPUT

RS-422

REVERSED

CABLE

INPU

120VAC

PGM

MON

CM9760-MDA

COM1COM2

OUTPUT

RS-422

REVERSED

CABLE

INPU

120VAC

PGM

MON

CM9760-MDA

(LAST UNIT)

COM1COM2

UNIT ID

OUTPUT

RS-422

REVERSED

CABLE

*A wall block is used to convert the DB9 connector of the PC to an

RJ-45 connector for connection to the COM1 port of the MDA. Refer

to Figure 5 for a wiring diagram of PC-to-MDA connections.

Figure 39. PC Connection to Up to 16 Daisy-Chained MDA Units

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

+12 VDC

GND

12 VDC POWER SUPPLY

(IF NECESSARY)

WALL

BLOCK

FEMALE

DB9

PC MALE DB9

SERIAL PORT

PV130

RS-422 REVERSED CABLE

CM9760-CDU-T

100-240V

Tx+

Tx-

GND

OUT

10-24 ACDC

RS-422

SHIELDED

TWISTED

PAIR*

MDA 1

MDA 17

MDA 33

MDA 49

RS-422

120VAC

PGM

MON

PGM

MON

PGM

MON

PGM

MON

REVERSED

CABLE

COM1COM2

UNIT ID

MDA 2

MDA 18

MDA 34

MDA 50

120VAC

RS-422

120VAC

PGM

MON

PGM

MON

PGM

MON

PGM

MON

REVERSED

CABLE

COM1COM2

UNIT ID

MDA 3

MDA 19

MDA 35

MDA 51

RS-422

120VAC

PGM

MON

PGM

MON

PGM

MON

PGM

MON

REVERSED

CABLE

COM1COM2

UNIT ID

MDA 16

MDA 32

MDA 48

MDA 64

RS-422

120VAC

PGM

MON

PGM

MON

PGM

MON

PGM

MON

REVERSED

CABLE

COM1COM2

UNIT ID

*BELDEN 9843 OR SIMILAR CABLE

Figure 40. PC Connection to over 16 MDA Units (Maximum of 64 MDA Units)

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

INPUT

120VAC

CM9760-CC1

PGM

MON

CM9760-MDA

COM1COM2

UNIT ID

OUTPUT

RS-422 REVERSED CABLE

INPUT

120VAC

PGM

MON

CM9760-MDA

COM1COM2

OUTPUT

RS-422 REVERSED CABLE

INPUT

120VAC

PGM

MON

CM9760-MDA

COM1COM2

OUTPUT

RS-422 REVERSED CABLE

INPUT

120VAC

PGM

MON

CM9760-MDA

(LAST UNIT)

COM1COM2

UNIT ID

OUTPUT

RS-422 REVERSED CABLE

Figure 41. CM9760-CC1 Connection to up to 16 Daisy-Chained MDA Units

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

CM9760-CC1

RS-422 REVERSED CABLE

CM9760-CDU-T

100-240V

Tx+

Tx-

GND

OUT

10-24 ACDC

RS-422

SHIELDED

TWISTED

PAIR*

MDA 1

MDA 17

MDA 33

MDA 49

RS-422

120VAC

PGM

MON

PGM

MON

PGM

MON

PGM

MON

REVERSED

CABLE

COM1COM2

UNIT ID

MDA 2

MDA 18

MDA 34

MDA 50

120VAC

RS-422

PGM

MON

PGM

MON

PGM

MON

PGM

MON

REVERSED

CABLE

COM1COM2

UNIT ID

MDA 3

MDA 19

MDA 35

MDA 51

120VAC

RS-422

120VAC

PGM

MON

PGM

MON

PGM

MON

PGM

MON

REVERSED

CABLE

COM1COM2

UNIT ID

MDA 16

MDA 32

MDA 48

MDA 64

RS-422

120VAC

PGM

MON

PGM

MON

PGM

MON

PGM

MON

REVERSED

CABLE

COM1COM2

UNIT ID

*BELDEN 9843 OR SIMILAR CABLE

Figure 42. CM9760-CC1 Connection to over 16 MDA Units (Maximum of 64 MDA Units)

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

CAMERA

INPUT

120VAC

PGM

MON

COM1COM2

UNIT ID

OUTPUT

CM9760-MDA

MULTIPLEXER

Figure 43. MDA Connected to Multiplexers

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

RS-422

KBD9760

RS-422

VIDEO

RS-422

CPU

(CM9760-CC1)

CAMERA 1

CAMERA

RS-422

CM9760-MXB

SYSTEM 9760

MATRIX BA

POWER SUPPLY

MADE IN USA

16 VIDEO

INPUTS

MATRIX BAY

MASTER

(CM9760-MXB)

DISTRIBUTION

AMPLIFIER

(CM9760-MDA)

VIDEO

CM9760-MDA

Master Distribution Amplifier

Made In USA

SYSTEM 9760

COM 1

MATRIX SYSTEM

MULTIPLEXER

4 VIDEO OUTPUTS

FOR EACH OF THE

16 INPUTS

VCR

SPARE

= VIDEO

= DATA

Figure 44. Non-Coaxitron System Setup

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

COAXITRON^®

TRANSLATOR

(CM9760-CXTA)

VIDEO

CM9760-CXT

Coaxitron^®Translator

Made in USA

SYSTEM 9760

COAXITRON^®

PTZ DOME

CM9760-MXB

MATRIX BA

SYSTEM 9760

POWER SUPPLY

MADE IN USA

MATRIX BAY

(CM9760-MXB)

LOOPING VIDEO

SIGNALS FROM

COAXITRON^®

RS-422 DATA

TRANSLATOR

CPU (CM9760-CC1)

INITIAL

PROGRAMMING

ONLY (PC OR

CM9760-KBD)

MASTER DISTRIBUTION

AMPLIFIER, MDA 1

(CM9760-MDA)

CM9760-MDA

Master Distribution Amplifier

Made In USA

SYSTEM 9760

COM 1

MULTIPLEXER

CM9760-KBD

4 VIDEO OUTPUTS

FOR EACH OF THE

16 INPUTS

VCR

SPARE

= VIDEO

= DATA

Figure 45. Coaxitron with System 9760 Setup

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO

CM6800

SYSTEM 6800

Matrix Switcher/Controller

Made in USA

CAMERA

COAXITRON CM6800 MATRIX SYSTEM

LOOPING VIDEO

CAMERA

COM1

CM9760-MDA

Master Distribution Amplifier

Made In USA

SYSTEM 9760

MDA

INITIAL

PROGRAMMING

ONLY (PC OR

CM9760-KBD)

MULTIPLEXER

VCR

4 VIDEO OUTPUTS

FOR EACH INPUT

CM9760-KBD

SPARE

= VIDEO

= DATA

Figure 46. Coaxitron with System 6800 Setup

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

CAMERA

CAMERA INPUT

INPUT

120VAC

PGM

MON

COM1COM2

UNIT ID

OUTPUT

PELCO CM9760-MDA

THIRD-PARTY EQUIPMENT

FOR SENDING OF

MESSAGE TEXT

(RS-232/RS-422)

MONITOR

VCR

Figure 47. CM9760-MDA Message Text Sent from Third-Party Equipment

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX B – SUPPORTED TITLE AND MESSAGE TEXT

CHARACTERS

The CM9760-MDA supports the characters listed in Table G for display of title and message

text. If a character is not supported, the CM9760-MDA PC Setup program on a PC blocks

entry of the character in title and message lines. If you enter a title in the CM9760-MDA

SETUP dialog box or enter a message in the Message Text Editing dialog box and type a

character that is not supported, the CM9760-MDA PC Setup program prevents entry of the

character.

Table G. Supported Title and Message Text Character Set

/ (forward slash) (see NOTE below)

* (asterisk)

space

: (colon)

< (less than)

> (greater than)

- (hyphen)

. (period)

, (comma)

; (semicolon)

? (question mark)

NOTE: The forward slash can be displayed in a message but cannot be displayed in a

title.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX C – MESSAGE TEXT INSERTION COMMANDS

As discussed in the Set Message Text section of this manual, the CM9760-MDA supports

message text insertion protocol commands for display of text messages. The commands

can be used by third-party equipment when interfacing the COM 1 or COM 2 port of the

CM9760-MDA using the RS-232 or RS-422 communication standard.

Table H provides a listing of the message text insertion commands based upon the function

of the command.

Table H. CM9760-MDA Message Text Insertion Commands

Command Function

Command Format

Set one line of message text

on an MDA unit/channel/row

[A0][CB][00][Unit ID][Channel][Row][Message

Text (1-24 characters)][AF][Checksum]

Set up to five lines of message

text on an MDA unit/channel

[A0][CB][01][Unit ID][Channel][Message Text (4 to

124 characters)][AF][Checksum]

Query the message text that is

[A0][CB][02][Unit ID][Channel][AF][Checksum]

displayed on an MDA unit/channel*

Clear one line of message text

from an MDA unit/channel/row

[A0][CB][03][Unit ID][Channel][Row]

[AF][Checksum]

Clear all lines of message text

from an MDA unit/channel

[A0][CB][04][Unit ID][Channel][AF][Checksum]

Clear all message text from all

[A0][CB][05][Unit ID][AF][Checksum]

channels of the selected MDA unit

Format the text block display on

MDA unit/channel

[A0][CB][06][Unit ID][Channel][Format][Rows to

Display/Scroll][Row Separation][High Message

Time][Low Message Time][AF][Checksum]

Format the text block display on

all channels for the selected MDA

unit

[A0][CB][07][Unit ID][Format][Rows to Display/

Scroll][Row Separation][High Message Time][Low

Message Time][AF][Checksum]

Query text block format on an

MDA unit/channel^†

[A0][CB][08][Unit ID][Channel][AF][Checksum]

Insert message text and scroll the

other rows upward

[A0][CB][09][Unit ID][Channel][Message Text (1-24

characters)][AF][Checksum]

*The MDA response to the message text query command is the command using function

byte 01.

^†The MDA response to the message format query command is the command using

function byte 06.

Note the following about the commands shown in Table H:

•

Data within brackets is expressed as hexadecimal data. Brackets are not part of the

commands—the brackets are used to separate the various parts of the command to

provide ease of readability.

•

First four bytes of each command are as follows:

[A0][CB][function byte][Unit ID]

where:

[A0] and [CB] = 2-byte header information

[function byte] = [00] to [09], which determines the command function

[Unit ID] = [00] to [63] in packed binary code decimal (BCD) format, which defines

the Unit ID number of the MDA

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

•

Optional command parameters depend on the function byte ([00] to [09]) and include

the following:

–

[Channel] = [00] to [15] in packed BCD format, which defines the channel number

of the MDA unit

[Row] = [01] to [05] in packed BCD format, which defines the row number in

which message text is to be set or cleared

[Message Text] = specifies the message text to be displayed:

•

1 to 24 characters for one line of message text

4 to 124 characters, where:

Minimum = 4 message separator bytes ([7F][7F][7F][7F]) and no message

text

Maximum = 124 bytes: 5 messages containing 24 characters each (120

message bytes) plus 4 message separator bytes ([7F][7F][7F][7F])

–

[Format] = [00] or [01], where:

[00] = displays message text below the title/time/date text

[01] = displays message text above the title/time/date text

–

[Row-Separation] = [00] to [28], which defines the number of blank rows

separating the title/time/date text and the message text displays

[Rows-to-Display/Scroll] = [00] to [05], which defines the number of message text

lines to be displayed. Also defines the number of message text lines to be

scrolled.

–

[High Message Time][Low Message Time] = Message time bytes that are

transmitted and received in packed BCD format. The message time bytes define

the number of seconds that the message text is to be displayed. The maximum

display time-out is 9,999 seconds. A display time-out of 0 seconds allows the text

to be displayed indefinitely or until overwritten.

•

Last two bytes of each command are as follows:

[AF][Checksum]

where:

–

[AF] = signals end of the command

[Checksum] = exclusive-or of all other bytes in the command

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

REGULATORY NOTICES

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class B digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However there is no guarantee that the interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

You may also find helpful the following booklet, prepared by the FCC: “How to Identify and

Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Govern-

ment Printing Office, Washington D.C. 20402.

Changes and modifications not expressly approved by the manufacturer or registrant of this

equipment can void your authority to operate this equipment under Federal Communica-

tions Commission’s rules.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union

regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

WARRANTY AND RETURN INFORMATION

WARRANTY

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100

or (559) 292-1981 to obtain a RepairAuthorization number (RA), and provide the

following information:

Pelco will repair or replace, without charge, any merchandise proved defective

in material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

1. Model and serial number

•

Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and

MC3500/MC3600 Series); two years on all other cameras.

Three years on Genex^®Series (multiplexers, server, and keyboard) and 090

Series Camclosure^®Camera System.

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under

the warranty conditions stated above, please include a written explanation with

the product when returned.

•

Two years on 100/150, 200 and 300 Series Camclosure^®Camera Systems.

Two years on all standard motorized or fixed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM8500/CM9500/CM9740/

CM9760 Matrix, DF5 and DF8 Series Fixed Dome products.

Two years on Spectra^®, Esprit^®, and PS20 Scanners, including when used in

continuous motion applications.

Method of return shipment shall be the same or equal to the method by which the

item was received by Pelco.

•

Two years on Esprit and WW5700 series window wiper (excluding wiper blades).

Eighteen months on DX Series digital video recorders.

One year (except video heads) on video cassette recorders (VCRs). Video

heads will be covered for a period of six months.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call

the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number

(CA number if returned for credit, and RA number if returned for repair).

•

Six months on all pan and tilts, scanners or preset lenses used in continuous

motion applications (that is, preset scan, tour and auto scan modes).

All merchandise returned for credit may be subject to a 20% restocking and

refurbishing charge.

Pelco will warrant all replacement parts and repairs for 90 days from the date of

Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid

to Pelco, Clovis, California. Repairs made necessary by reason of misuse,

alteration, normal wear, or accident are not covered under this warranty.

Goods returned for repair or credit should be clearly identified with the assigned

CA or RA number and freight should be prepaid. Ship to the appropriate address

below.

Pelco assumes no risk and shall be subject to no liability for damages or loss

resulting from the specific use or application made of the Products. Pelco’s

liability for any claim, whether based on breach of contract, negligence,

infringement of any rights of any party or product liability, relating to the Products

shall not exceed the price paid by the Dealer to Pelco for such Products. In no

event will Pelco be liable for any special, incidental or consequential damages

(including loss of use, loss of profit and claims of third parties) however caused,

whether by the negligence of Pelco or otherwise.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico:

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico:

Intermediate Consignee

American Overseas Air Freight

320 Beach Road

Burlingame, CA 94010

USA

Ultimate Consignee

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

USA

The above warranty provides the Dealer with specific legal rights. The Dealer may

also have additional rights, which are subject to variation from state to state.

REVISION HISTORY

Manual #

C573M

C573M-A

Date

6/98

6/99

Comments

Original version.

Rev. A. Added Regulatory Notices section. Revised Overview section. Added FCC certification. Revised the Installation section

and added new drawings. Expanded the address switch settings chart from 512 cameras to 1,024 cameras. Added Reset and

Master Clock sections. Added a video coaxial cable wiring distances chart. Removed the menu system map and reorganized

material in the Software and Programming Methods sections. Reorganized and revised the Specifications section. Removed

section numbers, and renumbered figures and cross references throughout the manual.

C573M-B

C573M-C

C573M-D

4/00

8/02

11/03

Added information on programming with the KBD200 and KBD300 keyboards. Added reset information to a Caution at a later date.

Revised Figure 5.

Revised manual to support version 1.40 (ECO #03-8629) and 2.05 (ECO #03-9517) of the CM9760-MDA Setup program. Also

revised and added information regarding support of maximum of 16 daisy-chained MDA units.

® Pelco, the Pelco logo, Spectra, Genex, Legacy, PelcoVision, Coaxitron, Esprit,

Camclosure, and System 9760 are registered trademarks of Pelco.

® Microsoft and Windows are registered trademarks of Microsoft Corporation.

™ System 9740 is a trademark of Pelco.

Pelco Manual C573M-D (11/03)

Download from Www.Somanuals.com. All Manuals Search And Download.

Petsafe Pet Fence PIG20 11041 User Manual
Philips Bottle Warmer SCF121 12 User Manual
Philips Coffeemaker RI7448 User Manual
Philips Computer Drive AZ 8070 User Manual
Philips Stereo System FW 315C User Manual
Philips Work Light P 5899 A User Manual
Pioneer DVD Recorder DVR 216MBK User Manual
Polycom Telephone F9600 User Manual
Pride Mobility Mobility Aid Jazzy 600 XL User Manual
ProForm Treadmill 635CW User Manual