®
CM3000
Fixed Camera Mount
Installation/Operation
C230M Rev B (7/91)
U
®
L
LISTED
1.0 WARNINGS
Prior to installation and use of this product, the following WARNINGS should be
observed.
1. Installation and servicing should only be done by Qualified Service Personnel
and conform to all Local codes.
2. Installation shall be done in accordance with all local and national electrical
and mechanical codes utilizing only approved materials.
3. Use only installation methods and materials capable of supporting four times
the maximum specified load.
4. Use stainless steel hardware to fasten the mount to outdoor surfaces.
5. To prevent damage from water leakage when installing a mount outdoors on a
roof or wall, apply sealant around the bolt holes between the mount and mount-
ing surface.
The product and/or manual may bear the following
mark:
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this
unit.
Please thoroughly familiarize yourself with the information
in this manual prior to installation and operation.
Pelco • 300 W. Pontiac Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981
FAX (800) 289-9150 or (1-559) 292-3827 • DataFax (800) 289-9108 or (1-559) 292-0435
International customers call (1-559) 292-1981 or FAX (1-559) 348-1120
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0 SPECIFICATIONS
Pan Adjustment:
Tilt Adjustment:
Construction:
Finish:
360°
90°
Aluminum
Polyester powder coat
See Figure 2
Dimensions:
Figure 2. CM3000 Dimension Drawing
Pelco Manual C230M Rev B (7/91)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
5.0 WARRANTY AND
WARRANTY
RETURN INFORMATION
Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one (1) year after the date of shipment.
Exceptions to this warranty are as noted below:
•
•
Two (2) years on all standard motorized and fixed focal length lenses.
Two (2) years on Legacy®, Intercept®, CM8500/CM9500/CM9750 Matrix,
Spectra™, DF5 Series and DF8 Fixed Dome products.
•
•
•
Two (2) years on WW5700 series window wiper (excluding wiper blades).
Two (2) years on cameras.
Six (6) months on all pan and tilts, scanners or preset lenses used in continu-
ous motion applications (e.g., preset scan, tour and auto scan modes).
Pelco will warranty all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to
Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration,
normal wear, or accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss result-
ing from the specific use or application made of the Products. Pelco’s liability for
any claim, whether based on breach of contract, negligence, infringement of any
rights of any party or product liability, relating to the Products shall not exceed the
price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable
for any special, incidental or consequential damages (including loss of use, loss of
profit and claims of third parties) however caused, whether by the negligence of
Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the
following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under
the warranty conditions stated above, please include a written explanation with the
product when returned.
Ship freight prepaid to:
Pelco
300 West Pontiac Way
Clovis, CA 93612-5699
Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the
factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA
number if returned for credit, and RA number if returned for repair). Goods returned
for repair or credit should be clearly identified with the assigned CA/RA number and
freight should be prepaid. All merchandise returned for credit may be subject to a
20% restocking and refurbishing charge.
Ship freight prepaid to:
Pelco
®Pelco and the Pelco logo are
registered trademarks of Pelco.
©Copyright 1997, Pelco. All rights
reserved.
300 West Pontiac Way
Clovis, CA 93612-5699
4
Pelco Manual C230M Rev B (7/91)
Download from Www.Somanuals.com. All Manuals Search And Download.
|