®
PELCO
PO
W
ER
PMC901-X
9-Inch Color
Video Monitor
Installation/
Operation Manual
C1911M (4/98)
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120
Download from Www.Somanuals.com. All Manuals Search And Download.
1.0 GENERAL
1.1 IMPORTANT SAFEGUARDS AND WARNINGS
Please thoroughly familiarize yourself with the information in this manual prior to
installation and operation.
Read Instructions
Safety and operating instructions should be read before the monitor is operated.
Retain Instructions
Safety and operating instructions should be retained for future reference.
Heed Warnings
All warnings on the monitor and in the operating instructions should be followed.
Follow Instructions
All operating and use instructions should be followed.
Cleaning
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Attachments
Use only attachments recommended by Pelco.
Water and Moisture
Do not use this monitor near water - for example, near a kitchen sink, in a wet
basement or near a swimming pool - unless the monitor is specifically marked “For
Use in Wet Locations.”
Accessories
Do not place this monitor on an unstable cart, stand, table, or mount. The monitor
may fall, causing serious injury to a child or adult and serious damage to the moni-
tor. Use only with a mount recommended by Pelco. When mounting the monitor,
follow Pelco’s installation instructions, and use only mounting accessories recom-
mended by Pelco.
Cart & Stand
A monitor and cart combination should be moved with care. Quick stops, excessive
force, and uneven surfaces may cause the monitor and cart combination to over-
turn.
Ventilation
Slots and openings in the cabinet are provided for ventilation to ensure reliable
operation of the monitor and to protect it from overheating. These openings must
not be blocked or covered. The openings should never be blocked by placing the
monitor on furniture, carpet, or similar surfaces. The monitor should never be placed
near or over radiators or heat registers. This monitor should not be placed in a built-
in installation, such as a bookcase or rack, unless proper ventilation is provided.
Power Sources
This monitor should only be operated from the type of power source indicated on
the back panel label. If you are not sure of the type of power to your installation
location, consult your local electrical building official or power company.
Grounding
This monitor is equipped with a grounding plug. This plug will only fit into a ground-
ing outlet. This is a safety feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet. Do not defeat the grounding
plug since it is provided to ensure your safety.
Pelco Manual C1911M (4/98)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Power-Cord Protection
Power cords should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them. When routing power cords, pay attention to
cords at plugs, convenience receptacles, and the point where they exit from the
monitor.
Overloading
Do not connect more power plugs to one outlet than it can safely handle. This may
overload wall outlets and extension cords and can result in a risk of fire or electric
shock.
Object and Liquid Entry
Never push objects of any kind through openings in this monitor as they may touch
dangerous voltage points or “short-out” electrical parts and could result in a fire or
electric shock. Never spill liquid of any kind on the monitor.
Servicing
Do not attempt to service this monitor yourself. Opening or removing covers may
expose you to dangerous voltages or other hazards. Refer all servicing to qualified
service personnel.
Damage Requiring Servicing
Unplug this monitor from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power cord or plug is damaged.
b. If liquid has been spilled or objects have fallen into the monitor.
c. If the monitor is not marked “Suitable for Wet Locations” and it has been ex-
posed to rain or water.
d. If the monitor does not operate normally by following the operating instruc-
tions, adjust only those controls that are covered by the operating instructions.
Improper adjustment of other controls may result in damage and may require
extensive work by a qualified technician to restore the monitor to its normal
operation.
WARNING: This prod-
uct has been evaluated
for INDOOR USE ONLY
unless it bears the mark-
ing “For Use in Wet Lo-
cations.”
e. If the monitor has been dropped or the cabinet has been damaged.
f.
When the monitor exhibits a distinct change in performance - this indicates a
need for service.
WARNING: To reduce
the risk of electric shock
hazard, do not remove
the monitor cover. This
monitor cannot be ser-
viced by the user and
must be sent to a quali-
fied service person for
repair.
Replacement Parts
When replacement parts are required, be sure the service technician has used
replacement parts specified by Pelco or have the same characteristics as the origi-
nal part. Improper substitutions may result in fire, electric shock, or other hazards.
Safety Checks
Upon completion of any service or repairs to this monitor, ask your service techni-
cian to perform safety checks to determine that the monitor is in proper operating
condition.
4
Pelco Manual C1911M (4/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage constituting a
risk of electric shock is present within this unit.
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this
unit.
Please thoroughly famil-
iarize yourself with the in-
formation in this manual
prior to installation and
operation.
CAUTION:
RISK OF
ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
1.2 REGULATORY NOTICES
NOTE: This equipment has been tested and found to comply with the limits of a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are de-
signed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However there is no guarantee that
the interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try and cor-
rect the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
1.3 UNPACKING INSTRUCTIONS
Unpack and inspect all parts carefully.
The following items are supplied:
1
1
Monitor
Installation/Operation Manual (C1911M)
Be sure to save the shipping carton, boxes and inserts. They are the safest materi-
als in which to make future shipments.
If an item appears to have been damaged in shipment, replace it properly in its box
and contact the factory at 1-800-289-9100 or 1-559-292-1981 for a replacement.
(International customers fax 1-559-348-1120 for authorization and instructions.)
If an item needs to be returned to the factory for repair, consult the WARRANTY
AND RETURN section of this manual for instructions.
Pelco Manual C1911M (4/98)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2.0 DESCRIPTION
The PMC901-X is a 9-inch (23 cm) color video monitor for specialized surveillance
and industrial CCTV applications. The color monitor provides excellent picture quality
and convenient control of functions. It is ideal for time-lapse and event-alarm VCR
systems or color video multiplexers.
2.1 MODEL
PMC901-X
Color video monitor, 9-inch (23 cm) picture display, PAL, 230
VAC.
2.2 CERTIFICATIONS
The products identified below have been tested and certified for agency compli-
ance as noted below.
Agency Compliance Certification
Model
CE
FCC
UL
CSA/cUL
PMC901-X
X
X
X
X
Applicable CE, FCC, UL, and CSA/cUL directives/standards:
•
93/68/EEC–CE Mark Directive
89/336/EEC, 92/31/EEC–Electromagnetic Compatibility (EMC) Directives
EN 55022: 1984 Class B–Radio-frequency emissions limits
EN 50082-1: 1992–Immunity standard
IEC 801-2: 1984–ESD immunity
IEC 801-3: 1984–Radiated field immunity
IEC 801-4: 1988–Electrical transients
72/23/EEC–Low Voltage Directive (EMC)
EN 60950–Safety of ITE equipment
•
•
•
FCC–47 CFR Part 15, Subpart B, Class B
UL Listed
CSA Class 2226 02–Audio and Video Equipment (LR 701756)–CAN/CSA-
C22.2 No. 1
CSA Class 3862 07–Information Technology Equipment (LR 101187)–CSA
Std C22.2 No. 950
6
Pelco Manual C1911M (4/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
3.0 INSTALLATION
3.1 MOUNTING
The monitor has rubber feet and may be placed on any horizontal surface, such as
a desk or table.
The monitor also may be installed in a 19-inch (48.26 cm) rack or on a wall, ceiling,
or pedestal mount. Follow the instructions that accompany the rack kit or mount.
3.2 CONNECTIONS
1. Connect a video cable from the video source to the BNC connector labeled
VIDEO IN on the rear panel of the monitor (refer to Figure 1). Refer to Table A
for the type of video coaxial cable to use.
2. When the video signal is looped through the monitor, connect a video cable
from the BNC connector labeled VIDEO OUT to the equipment which requires
a video signal input (refer to Figure 1).
3. Set the termination switch on the monitor to the 75-ohm or OPEN position
(refer to Figure 1).
4. Plug in the power cord.
Table A. Video Coaxial Cable Wiring Distances
Cable Type*
Maximum Distance
RG59/U
RG6/U
750 ft (229 m)
1,000 ft (305 m)
1,500 ft (457 m)
RG11/U
*Minimum cable requirements:
75 ohms
All-copper center conductor
All-copper braided shield with 95-percent braid coverage
Pelco Manual C1911M (4/98)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1. Monitor Connections
8
Pelco Manual C1911M (4/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0 OPERATION
The center detent position on all front panel controls is the normal setting; a subcontrol
is provided for presetting each control. The subcontrol adjustments should be ad-
justed by a qualified service technician only.
There are no external vertical or horizontal hold controls. The monitor contains
circuitry to lock the synchronization internally.
To operate the monitor:
Refer to Figure 2 for the location of the front panel controls.
1. Turn on the POWER switch; LED indicator will light. Allow the monitor to warm
up for about 30 seconds.
2. Adjust the color control to the center detent position. The monitor screen should
provide a color image. If the image requires more color saturation, rotate the
control clockwise. If colors appear too saturated, adjust the control counter-
clockwise.
NOTE: Overdrive of the white por-
tions of the video, sufficient to cause
blooming, can significantly shorten
the service life of the CRT. Always
adjust the brightness and contrast
controls to the center detent posi-
tion or towards a minimum setting
to enhance monitor life expectancy.
3. Adjust the brightness and contrast controls to the center detent position. If
dark scene areas require enhancement, the brightness control can be rotated
clockwise. If the “black level,” which determines the darkest portion of the pic-
ture, appears too light, rotate the brightness control counterclockwise.
Figure 2. Front Panel Controls
Pelco Manual C1911M (4/98)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5.0 MAINTENANCE
The PMC901 monitor is engineered to provide years of reliable service. Regularly
scheduled maintenance is not required. Clean the outer surface of the PMC901
with a damp non-abrasive cleaning cloth. Be sure not to get any cleaner inside the
PMC901 case.
This monitor contains no user-serviceable components. Maintenance, beyond the
adjustments described in Section 4.0, OPERATION, should be attempted only by
trained technical personnel.
10
Pelco Manual C1911M (4/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
6.0 SPECIFICATIONS
ELECTRICAL
Input Voltage:
230 VAC, 50 Hz
Power
Consumption:
75.6 W
PAL
Color System:
General:
Automatic degaussing; fast warm-up time
Display Tube:
High resolution, 9-inch (23 cm) diagonal, 90° deflection, inte-
gral implosion protection
Viewing Diagonal: 8.9 inches (22.5 cm)
Resolution:
280 TV lines minimum, 300 TV lines typical
Linearity
Horizontal:
Vertical:
Within 10%
Within 10%
Video Input:
1.0 Vp-p composite video, sync negative
Internally derived
Synchronization:
Controls
Front Panel:
Brightness - rotary knob
Contrast - rotary knob
Color - rotary knob
Power - On/off push-button switch and LED)
(Recessed, adjustable range)
Subcolor
Service:
Sub-brightness
Subcontrast
Rear Panel:
Connectors:
AC Power Cord:
GENERAL
Construction:
Finish:
75 ohms or OPEN (high impedance), switchable
Two BNC connectors (VIDEO IN and OUT)
3-wire power cord with grounded plug; 7.4-foot (2.3 m) length
Steel cabinet with plastic front
Black matte finish
Temperature:
Humidity:
32° to 104°F (0° to 40°C)
10% to 80% relative, non-condensing
8.9" H x 8.7" W x 12.5" D (22.6 cm x 22.0 cm x 31.7 cm)
Dimensions:
Weight:
Unit
Shipping
15.2 lb (6.90 kg)
17.0 lb (7.71 kg)
(Design and product specifications subject to change without notice.)
Pelco Manual C1911M (4/98)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
7.0 WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-
2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have
a five-year warranty.
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed
dome products.
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
•
•
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.
All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California.
Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not
covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the
specific use or application made of the Products. Pelco’s liability for any claim, whether based
on breach of contract, negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products.
In no event will Pelco be liable for any special, incidental or consequential damages (including
loss of use, loss of profit and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-
1981 to obtain a Repair Authorization number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty
conditions stated above, please include a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
RETURNS
Inordertoexpeditepartsreturnedtothefactoryforrepairorcredit, pleasecallthefactoryat(800)
289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit,
and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
GoodsreturnedforrepairorcreditshouldbeclearlyidentifiedwiththeassignedCAorRAnumber
and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed
to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
Endura and ExSite are trademarks of Pelco.
© Copyright 1998, Pelco. All rights reserved.
12
Pelco Manual C1911M (4/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
|