Digital Video Cassette Recorder
AJ-
P
Operating Instructions
P
Printed in Japan
VQT8368
F1099W @
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Playback operations . . . . . . . . . . . . . . . . . . . . . . .34
Introduction . . . . . . . . . . . . . . . . . . . . . . . .4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . .4
System Configuration . . . . . . . . . . . . . . . .5
1. Regular-speed playback and still-picture
playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
2. Cue playback and review playback . . . . . . . .35
3. Linear 0.3a speed playback . . . . . . . . . . . . . .36
4. Variable speed playback . . . . . . . . . . . . . . . .36
5. Reading and displaying the time data . . . . . .37
Parts and Their Functions . . . . . . . . . . . .6
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
1. Operating area . . . . . . . . . . . . . . . . . . . . . . . . .7
2. Status display area . . . . . . . . . . . . . . . . . . . . . .9
3. Control area . . . . . . . . . . . . . . . . . . . . . . . . . .11
4. Time code setting area . . . . . . . . . . . . . . . . . .12
Connector panel . . . . . . . . . . . . . . . . . . . . . . . . . .13
1. Audio section . . . . . . . . . . . . . . . . . . . . . . . . .14
2. Video section . . . . . . . . . . . . . . . . . . . . . . . . .15
3. Power supply and other sections . . . . . . . . . .16
Superimposed Screens . . . . . . . . . . . . .38
Setup (Initial Settings) . . . . . . . . . . . . . .40
Setting method using on-screen menus . . . . . . . .40
How to set the time/date . . . . . . . . . . . . . . . . . . . .41
How to return to the factory settings . . . . . . . . . . .41
How to set the user default settings . . . . . . . . . . .42
How to load the user settings . . . . . . . . . . . . . . . .42
How to protect the menus . . . . . . . . . . . . . . . . . . .43
How to release the menu protection . . . . . . . . . . .43
How to display the DIAG menu . . . . . . . . . . . . . .44
Preparations . . . . . . . . . . . . . . . . . . . . . .17
Preparing to supply power . . . . . . . . . . . . . . . . . .17
1. When using an AC adapter . . . . . . . . . . . . . .17
2. When using a battery pack . . . . . . . . . . . . . . .18
Preparing the cassette tape . . . . . . . . . . . . . . . . .19
1. Concerning tapes . . . . . . . . . . . . . . . . . . . . . .19
2. How to insert a cassette tape . . . . . . . . . . . . .20
3. How to eject a cassette tape . . . . . . . . . . . . .21
Setup Menus . . . . . . . . . . . . . . . . . . . . . .45
BASIC menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
OPERATION menu . . . . . . . . . . . . . . . . . . . . . . .46
INTERFACE menu . . . . . . . . . . . . . . . . . . . . . . . .48
TAPE PROTECT menu . . . . . . . . . . . . . . . . . . . .48
TIME CODE menu . . . . . . . . . . . . . . . . . . . . . . . .49
VIDEO menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
AUDIO menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
WARNING & ALARM menu . . . . . . . . . . . . . . . . .52
Recording . . . . . . . . . . . . . . . . . . . . . . . . .22
Preparing to record . . . . . . . . . . . . . . . . . . . . . . . .22
1. Connecting the equipment . . . . . . . . . . . . . . .22
2. Setting the video inputs . . . . . . . . . . . . . . . . .23
3. Setting the audio inputs . . . . . . . . . . . . . . . . .25
4. Setting the time data . . . . . . . . . . . . . . . . . . . .26
Recording operations . . . . . . . . . . . . . . . . . . . . . .30
1. Recording using the CAMERA connector . . .30
2. Recording using the VIDEO IN connector . . .31
3. Stopping the recording temporarily . . . . . . . . .31
4. REC REVIEW function . . . . . . . . . . . . . . . . . .32
5. Auto back function . . . . . . . . . . . . . . . . . . . . .32
6. Preventing erroneous recording operations . .32
Replacing the Backup Battery . . . . . . . .53
Error Messages . . . . . . . . . . . . . . . . . . . .54
Emergency Eject . . . . . . . . . . . . . . . . . . .56
Warning System . . . . . . . . . . . . . . . . . . .57
Connector Signals . . . . . . . . . . . . . . . . . .59
CAMERA connector (26-pin) . . . . . . . . . . . . . . . .59
REMOTE connector (9-pin) . . . . . . . . . . . . . . . . .59
AUDIO connector (XLR 3-pin) . . . . . . . . . . . . . . .59
DC IN connector (XLR 4-pin) . . . . . . . . . . . . . . . .59
DC OUT connector (4-pin) . . . . . . . . . . . . . . . . . .59
Playback . . . . . . . . . . . . . . . . . . . . . . . . . .33
Preparing for playback . . . . . . . . . . . . . . . . . . . . .33
1. Selecting the sound to be monitored . . . . . . .33
Video Head Cleaning . . . . . . . . . . . . . . . .60
Condensation . . . . . . . . . . . . . . . . . . . . .60
Maintenance . . . . . . . . . . . . . . . . . . . . . . .60
Specifications . . . . . . . . . . . . . . . . . . . . .61
2. Playback in synchronization with the external
signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The AJ-D92 is a portable video cassette recorder in
the DVCPRO series.
While featuring the compact size, light weight and low
power consumption characteristic of a DVCPRO, the
AJ-D92 supports both the DVCPRO and DVCPRO 50
formats.
Needless to say, the DVCPRO series is suitable for a
wide spectrum of applications when it is used in
combination with an existing video camera.
An interactive system enables the unit’s settings to be
performed while monitoring the on-screen menus that
appear on the TV monitor.
Features
High picture quality
REC REVIEW function
Using tapes in the DVCPRO format, the product of the
latest compression technology, the recording rate can
be switched between 50 Mbps with higher picture
quality and 25 Mbps with longer recording time.
The unit comes with a REC REVIEW function: this
plays back the section immediately prior to the end of
the previous recording, thereby enabling the operator
to verify that the signals have been recorded properly.
Compact size and light weight
On-screen menu settings
Detailed function settings tailored to the individual
user can be performed on-screen.
15
1
The unit is 11 / ˝ (303 mm) wide, 5 / ˝ (139 mm)
16
2
7
high and 13 / ˝ (341 mm) deep, and weighs 12.98 lb
16
(5.9 kg). It is equipped with grips which come in
handy when the unit is to be carried.
Audio level controls featured
The levels of the signals for the four audio channels
Long-time recording and playback
can be adjusted for recording and playback.
When an L size cassette is used, the maximum
recording and playback time is 92 minutes in the 50
Mbps mode and 184 minutes° in the 25 Mbps mode.
Built-in power supply for phantom microphone
An internal switch can be used to switch the power
supply from +12 V to +48 V or vice versa.
° For AJ-5P92LP cassette tapes recorded using the DVCPRO
(25 Mbps) mode, use a VTR supporting DVCPRO (25 Mbps)
184 minute tapes.
Time codes
Incorporated inside the unit is a TCG/TCR (time code
generator/time code reader). It is also possible to
input time codes from an external source to enable
regeneration with an external time code.
Both L and M size cassettes supported
This unit employs a front loading mechanism to
support the recording or playback of DVCPRO or
DVCPRO 50 format size L and M cassette tapes.
9-pin remote control
This unit comes with a 9-pin remote control connector
so that the unit can be operated using an optional
external remote controller (model AJ-A95).
Frame-to-frame continuity function
By using the REC button and PAUSE button
together—a combination which activates the auto
back function—pictures can be joined smoothly with
no disturbances.
Safety check function
The status of the video input signals can be checked
on the signal level display window by pressing the
METER button. This helps to prevent errors in input
signal switching operations and mistakes in recording
due to a cable disconnection, etc.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
System Configuration
Video camera
VTR or other unit
AC adapter (AJ-B75)
Component signals
Composite signals
Switching
Video input signals
Microphone
Tape recorder
or other unit
Audio input signals a4 channels (CH1 – CH4)
AJ-D92
Control signal a1 channel
Video output signals a3 channels (composite)
Remote controller (AJ-A95)
or
Video monitor
Editor
Earphones
Headphones
VTR, FPU or
other unit
Audio output signals a5 channels
Stereo amplifier
Speakers
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
Front panel
The front panel consists of the following four areas:
1. Operating area
2. Status display area
3. Control area
4. Time code setting area
WARNING
LIGHT
M
-cassette
METER
Caution:Do not insert S-cassette or with adaptor
EJECT
CASSETTE IN
CH1 CH2 CH3 CH4
CH 1
UNI
CH 2
UNI
CH 3
CH 4
RESET
UNI
UNI
25
50
TC
CTL
UB
VAR
VAR
VAR
VAR
POWER
CH1
CH2
CH3
CH4
KEY INHIBIT
ON
OFF
ON
OFF
PAUSE/
STILL
STOP
MODE
PLAY
REC
PB
LEVEL
REW
PAGE
FF
SEARCH
MENU
DATA
DOWN
UP
SET
F
-RUN
SET
-RUN
SET
OFF
R
MENU
SHIFT
REC REVIEW
1. Operating area
2. Status display area
WARNING
LIGHT
M
-cassette
METER
Caution:Do not insert S-cassette or with adaptor
EJECT
CASSETTE IN
CH1 CH2 CH3 CH4
CH 1
UNI
CH 2
UNI
CH 3
CH 4
RESET
UNI
UNI
25
50
TC
CTL
UB
VAR
VAR
VAR
VAR
POWER
CH1
CH2
CH3
CH4
KEY INHIBIT
ON
OFF
ON
OFF
PAUSE/
STILL
STOP
MODE
PLAY
REC
PB
LEVEL
REW
PAGE
FF
SEARCH
MENU
DATA
DOWN
UP
SET
F
-RUN
SET
-RUN
SET
OFF
R
MENU
SHIFT
REC REVIEW
3. Control area
4. Time code setting area
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
1. Operating area
WARNING
LIGHT
M
-cassette
METER
Caution:Do not insert S-cassette or with adaptor
EJECT
CASSETTE IN
CH1 CH2 CH3 CH4
CH 1
UNI
CH 2
UNI
CH 3
CH 4
RESET
UNI
UNI
25
50
TC
CTL
UB
VAR
VAR
VAR
VAR
POWER
CH1
CH2
CH3
CH4
KEY INHIBIT
ON
OFF
ON
OFF
PAUSE/
STILL
STOP
MODE
PLAY
REC
PB
LEVEL
REW
PAGE
FF
SEARCH
MENU
DATA
DOWN
UP
SET
F
-RUN
SET
-RUN
SET
OFF
R
MENU
SHIFT
REC REVIEW
1 POWER ON/OFF switch
4 STOP button
This switch is used to turn the unit’s power on and
off.
This button is pressed to stop the tape travel.
The tape drum continues to rotate even in the stop
mode, and the tape remains in close contact with
the drum.
When the stop mode continues beyond the
prescribed period of time, the unit is automatically
set to the standby OFF (half-loading) mode in order
to protect the tape.
The stop mode is established immediately after a
cassette has been inserted into the unit.
This button functions as the MODE button when
performing the on-screen menu setting.
When it is set to ON, the signal level display
window and status display window are displayed.
The unit’s power is turned on and off in tandem with
the power of the units (camera and remote
controller connected to the CAMERA terminal and
DC OUT socket) whose power is supplied from the
unit.
2 Cassette insertion slot
Press the cassette insertion slot cover to open it,
and then insert the cassette.
5 PLAY button and lamp
After the cassette has been inserted or ejected, the
cover must be closed for use.
<Notes>
This button is pressed to commence playback.
Recording is commenced when it is pressed
together with the REC button.
News gathering cassettes and general-purpose
O
cassettes are inserted into this slot.
Do not insert DV cassettes which are designed
for general consumer applications.
Open the cassette insertion slot cover before
issuing the EJECT command from a remote
controller when a controller has been connected.
The unit will not respond to the EJECT command
if its cover is still closed.
The button’s lamp lights during playback, recording
or pause.
This button functions as the DATA– button when
performing the on-screen menu setting.
O
6 REC button and lamp
Recording is commenced when this button is
pressed together with the PLAY button.
During recording the button’s lamp flashes; during
rec-pause it lights.
3 EJECT button
This button is pressed to eject the cassette.
When the cassette insertion slot cover is pressed
and opened and the EJECT button is pressed, the
tape is unloaded, and several seconds later it is
automatically ejected.
E-E signals can be monitored when the button is
pressed in the stop mode.
This button functions as the DATA+ button when
performing the on-screen menu setting.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
7 PAUSE/STILL button and lamp
: SEARCH button and lamp
This button is pressed during recording or playback
to temporarily stop (pause) the tape.
When it is pressed during recording, the tape stops
temporarily. Recording is resumed when it is
pressed again.
When it is pressed during playback, the still picture
mode is established. Playback is resumed when it
is pressed again.
Noise may be heard on the playback pictures: this
is normal and not indicative of malfunctioning.
The button’s lamp flashes during temporary stop.
When it is pressed again, temporary stop is
released, and the lamp goes off.
This button is pressed to initiate cue, review,
forward linear 0.3a playback or reverse linear 0.3a
playback.
When it is pressed before pressing the FF button,
the tape is cued; if the REW button is pressed
instead of the FF button, the tape is reviewed.
The button’s lamp lights during cue or review.
When the SEARCH button is pressed during cue,
the fast forward mode is established, and when it is
pressed during review, the rewind mode is
established, and the lamp goes off.
When the FF button is pressed after the SEARCH
button was pressed in the temporary stop
(PAUSE/STILL) mode, the forward linear 0.3a
playback mode is established; if the REW button is
pressed instead of the FF button, the reverse linear
0.3a playback mode is established.
The button functions as the SET button when
performing the on-screen menu setting.
8 REW button and lamp
The button’s lamp flashes during linear 0.3a
playback.
When the SEARCH button is pressed during linear
0.3a playback, the temporary stop (PAUSE/STILL)
mode is established.
The button functions as the MENU-UP button when
performing the on-screen menu setting.
This button is pressed to rewind the tape.
When it is pressed after pressing the SEARCH
button, the tape will be reviewed at the speed which
was set in setup menu item No. 100 and played.
When it is pressed after pressing the SEARCH
button in the temporary stop (PAUSE/STILL) mode,
the reverse linear 0.3a playback mode is initiated.
Noise will appear during linear 0.3a playback: this
is normal and not indicative of malfunctioning.
The button’s lamp lights during rewinding, review
and reverse linear 0.3a playback.
; REC REVIEW button
When this button is pressed during REC PAUSE,
the operator can monitor whether the portion of the
tape immediately before the button was pressed
has been recorded properly.
When the respective operations are completed, the
lamp goes off, and the operation concerned is
stopped.
< KEY INHIBIT switch
The button functions as the PAGE button when
performing the on-screen menu setting.
When this is set to ON, all the function buttons
except for those which were set using setup menu
item No. 000 can no longer be operated.
Under the default setting, none of the control
buttons except for STOP and EJECT can be
operated.
When the switch is set to OFF, all the control
buttons are operational.
When connecting an external controller, set the
KEY INHIBIT switch to OFF to enable its use.
9 FF button and lamp
This button is pressed to fast forward the tape.
When it is pressed after pressing the SEARCH
button, the tape will be cued at the speed which
was set in setup menu item No. 100.
When it is pressed after pressing the SEARCH
button in the temporary stop (PAUSE/STILL) mode,
the forward linear 0.3a playback mode is initiated.
Noise will appear during linear 0.3a playback: this
is normal and not indicative of malfunctioning.
The button’s lamp lights during fast forwarding, cue
and forward linear 0.3a playback.
When the respective operations are completed, the
lamp goes off, and the operation concerned is
stopped.
The button functions as the MENU-DOWN button
when performing the on-screen menu setting.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
2. Status display area
WARNING
LIGHT
M
-cassette
METER
Caution:Do not insert S-cassette or with adaptor
EJECT
CASSETTE IN
CH1 CH2 CH3 CH4
CH 1
UNI
CH 2
UNI
CH 3
CH 4
RESET
UNI
UNI
25
50
TC
CTL
UB
VAR
VAR
VAR
VAR
POWER
CH1
CH2
CH3
CH4
KEY INHIBIT
ON
OFF
ON
OFF
PAUSE/
STILL
STOP
MOD
PLAY
REC
PB
LEVEL
REW
PAGE
FF
SEARCH
MENU
DATA
DOWN
UP
SET
F
-RUN
SET
-RUN
SET
OFF
R
MENU
SHIFT
REC REVIEW
Warning displays
Operating status displays
Time data display
DF
SLAVE
min
TCG
WIDE
RF
SERVO
HUMID
E
E
TAPE
BATT
F
F
Remaining tape display
Battery level display
h
s
frm SLACK
Remaining tape display
1 Status display window
This indicates the remaining tape time in segments.
The warning displays, operating status displays,
time data displays, remaining tape display and
battery level display can be checked in the window.
When all 7 segments light up, it means that there
is more than 21 minutes of tape remaining. (This
can be changed to more than 30 minutes using
the setup menu item No. 905.)
When the segment at the “E” (empty) end lights
up, it means that 3 minutes of the tape are left.
(This can be changed to 5 minutes using setup
menu item No. 905.)
When the segment at the “E” (empty) end starts
flashing, it means that 2 minutes of the tape are
left. (This can be changed to 3 minutes using
setup menu item No. 904.)
O
O
O
Warning displays
These indicate operating failures of the unit.
RF:
Recording or playback cannot be
performed. Video head clogging or a
circuit failure may be to blame.
SERVO: The drum servo and capstan servo
have failed to lock.
HUMID: Condensation has formed.
SLACK: A problem has occurred in the tape
wind-up operation.
If this happens during recording, the WARNING
lamp flashes, and a warning alarm sounds
intermittently.
Operating status displays
When all 7 segments flash, the WARNING lamp
remains lighted and the warning alarm sounds
continuously, it means that the tape has come to
its end.
O
These indicate the unit’s operating status.
DF:
This indicates that the drop frame mode
is established.
SLAVE: This indicates that the time code is
<Notes>
locked to the external time code.
The warning alarm is output from the PHONE
jack.
The warning alarm can be set using setup menu
items No. 902, 903 and 904.
O
TCG:
This indicates that the time code
generator’s signal is being output.
O
WIDE: This indicates that the wide mode is
established.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
Battery level display
This indicates the remaining battery charge in
segments. (See page 18)
4 25 Mbps and 50 Mbps mode lamps
In the 25 Mbps mode, the bottom lamp lights.
In the 50 Mbps mode, the top and bottom lamps
light.
When all 7 segments light up, it means that the
battery has a full charge.
O
O
O
As the battery continues to discharge, the
segments go off one by one in sequence.
When the segment at the “E” (empty) end starts
flashing, the WARNING lamp also flashes, and
the warning alarm sounds intermittently, it means
that the battery will soon be fully discharged.
When all 7 segments flash, the WARNING lamp
remains lighted and the warning alarm sounds
continuously, it means that the battery is now
fully discharged.
5 WARNING lamp
This lights or flashes when the remaining tape time
is less than 2 minutes, when the battery had
discharged or when a problem with the unit’s
operation has been detected.
O
6 LIGHT button
Each time this button is pressed, the lighting for the
signal level display window and status display
window is turned ON or OFF.
<Note>
The warning alarm can be set using setup menu
7 METER button
items No. 900 and 901.
This is used to switch what is displayed in the
signal level display window. Normally, the audio
level is displayed but when the METER button is
pressed, the display switches to the input video
signal level.
2 RESET button
When this button is pressed, the time data display
is reset.
When it is pressed in the CTL mode, the display is
reset to 00:00:00:00.
When the button is pressed again, the audio level
display is restored.
The time code display is reset to 00:00:00:00.
The user’s bit is reset to 00 00 00 00.
(Even when the input video signal level is
displayed, the audio level display will be
automatically restored after 5 seconds.)
3 DISPLAY switch
This is used to switch what is displayed in the
status display window.
CTL: The tape timer (control signal) is displayed.
TC: The time code is displayed.
8 CASSETTE IN lamp
This lights when the cassette tape has been
inserted. It flashes in the standby off (half-loading)
mode.
UB: The user’s bit is displayed.
What time data is to be displayed is determined in
two stages: first by the position selected by the
TCG selector switch, and second by the position of
the DISPLAY switch.
TCG selector
switch position
DISPLAY switch
position
Information
displayed
TC or CTL
UB
Time code
User’s bit
CTL
SET
CTL
F-RUN or R-RUN
TC
Time code
User’s bit
UB
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
3. Control area
Channel condition displays
WARNING
LIGHT
EMPHASIS
0
CH CONDI
0
10
10
M
-cassette
METER
20
20
Caution:Do not insert S-cassette or with adaptor
30
40
30
40
EJECT
CASSETTE IN
-dB
-dB
VIDEO
SDI
Y
PB
PR
CH1 CH2 CH3 CH4
CH 1
UNI
CH 2
UNI
CH 3
CH 4
RESET
UNI
UNI
25
50
TC
CTL
UB
VAR
VAR
VAR
VAR
POWER
CH1
CH2
CH3
CH4
KEY INHIBIT
ON
OFF
ON
OFF
PAUSE/
STILL
STOP
MODE
PLAY
REC
PB
LEVEL
REW
PAGE
FF
SEARCH
MENU
DATA
DOWN
UP
SET
F
-RUN
SET
-RUN
SET
OFF
R
MENU
SHIFT
REC REVIEW
1 Signal level display window
2 Recording level controls and UNI/VAR switch
These four controls are used to adjust the recording
levels of the four audio channel (CH1—CH4)
signals while monitoring the audio level display.
UNITY or VARIABLE can be selected using the
UNI/VAR switch for the recording level of each
control.
The audio levels are normally displayed here.
However, when the METER button is pressed, the
display switches to the input video signal levels.
When the METER button is pressed again, the
audio level display is restored.
When the power is turned on, the audio levels are
automatically displayed.
In the case of the audio level display, the three CH
CONDI (channel condition) segments indicate the
playback signal status.
UNI: The input signals are recorded with their
levels unchanged.
The levels cannot be adjusted using the
controls.
VAR: The signals are recorded at the levels
adjusted by the controls.
CH CONDI
Playback signal status
lighting position
2 PB LEVEL controls
0 or 1
2
Playback signals have an acceptable quality.
These four controls are used to adjust the playback
output levels of the four audio channel (CH1—CH4)
signals.
The playback signals have deteriorated in
quality slightly but playback is still possible.
The playback signals have deteriorated in
quality. When the segment on the left lights
frequently, the heads must be cleaned and the
unit’s interior inspected.
<Note>
3
When the 25M mode has been set, the sound will be
recorded and played back as two channels (CH1 and
CH2).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
4. Time code setting area
WARNING
LIGHT
M
-cassette
METER
Caution:Do not insert S-cassette or with adaptor
EJECT
CASSETTE IN
CH1 CH2 CH3 CH4
CH 1
UNI
CH 2
UNI
CH 3
CH 4
RESET
UNI
UNI
25
50
TC
CTL
UB
VAR
VAR
VAR
VAR
POWER
CH1
CH2
CH3
CH4
KEY INHIBIT
ON
OFF
ON
OFF
PAUSE/
STILL
STOP
MODE
PLAY
REC
PB
LEVEL
REW
PAGE
FF
SEARCH
MENU
DATA
DOWN
UP
SET
F
-RUN
SET
-RUN
SET
OFF
R
MENU
SHIFT
REC REVIEW
1 TCG selector switch
3 “+” button
This is used to set the advancing mode of the built-
in time code generator.
F-RUN: This position is used to advance the time
code continuously regardless of the unit’s
operation.
This is used to increase by 1 the figure for the
setting digit when the time code or user’s bit is to be
set.
4 “–” button
Set the switch here when aligning the time
code with the actual time or locking the
time code with an external signal.
This is used to decrease by 1 the figure for the
setting digit when the time code or user’s bit is to be
set.
SET:
Set the switch to this position when the
time code or user’s bit is to be set.
5 MENU switch
R-RUN: Set the switch to this position to advance
the time code only during recording. The
time code will then be recorded
continuously onto the tape where
continuity has been ensured between the
frames.
This is set to SET when performing settings using
the on-screen menu items.
For normal operation, keep it at the OFF position.
2 SHIFT button
This button causes the setting digit to flash when
the time code or user’s bit is to be set.
It becomes operational when the TCG selector
switch has been set to the SET position.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
Connector panel
The connector panel consists of the following three
sections:
1. Audio section
2. Video section
3. Power supply and other sections
1. Audio section
HEADPHONES
MIC POWER
CH1OFF
MIC POWER
CH2OFF
MIC POWER
CH3OFF
MIC POWER
CH4OFF
TC
VIDEO
OUT
AUDIO
OUT
ON
ON
ON
ON
IN
OUT
CAM
LINE
CAM
LINE
CAM
LINE
CAM
LINE
BREAKER
EARPHONE
-60
+4dB
-60
+4dB
-60
+4dB
-60
+4dB
VIDEO
OUT
1
2
PUSH
PUSH
PUSH
PUSH
CH 1
CH 2
CH 3
CH 4
PHONE
LEVEL
PHONE
SELECT
CH1 2
A
U
D
I
·
VIDEO IN
O
·
CH3 4
SUPER IMPOSE
I
N
OFF
ON
CAMERA
DC ... 12V 3A
DC IN
CH 1
CH 2
CH 3
CH 4
A
U
D
I
DC OUT
... 12V 200mA
REMOTE
O
COMPO-
NENT
COMPO-
SITE
O
U
T
2. Video section
HEADPHONES
EARPHONE
MIC POWER
CH1OFF
MIC POWER
CH2OFF
MIC POWER
CH3OFF
MIC POWER
CH4OFF
TC
VIDEO
OUT
AUDIO
OUT
ON
ON
ON
ON
IN
OUT
CAM
LINE
CAM
LINE
CAM
LINE
CAM
LINE
BREAKER
-60
+4dB
-60
+4dB
-60
+4dB
-60
+4dB
VIDEO
OUT
1
2
PUSH
PUSH
PUSH
PUSH
CH 1
CH 2
CH 3
CH 4
PHONE
LEVEL
PHONE
SELECT
CH1 2
A
U
D
I
·
VIDEO IN
O
·
CH3 4
SUPER IMPOSE
I
N
OFF
ON
CAMERA
DC ... 12V 3A
DC IN
CH 1
CH 2
CH 3
CH 4
A
U
D
I
DC OUT
... 12V 200mA
REMOTE
O
COMPO-
NENT
COMPO-
SITE
O
U
T
3. Power supply and other sections
HEADPHONES
EARPHONE
MIC POWER
CH1OFF
MIC POWER
CH2OFF
MIC POWER
CH3OFF
MIC POWER
CH4OFF
TC
VIDEO
OUT
AUDIO
ON
ON
ON
ON
IN
OUT
OUT
CAM
LINE
CAM
LINE
CAM
LINE
CAM
LINE
BREAKER
-60
+4dB
-60
+4dB
-60
+4dB
-60
+4dB
VIDEO
OUT
1
2
PUSH
PUSH
PUSH
PUSH
CH 1
CH 2
CH 3
CH 4
PHONE
LEVEL
PHONE
SELECT
CH1 2
A
U
D
I
·
VIDEO IN
O
·
CH3 4
SUPER IMPOSE
I
N
OFF
ON
CAMERA
DC ... 12V 3A
DC IN
CH 1
CH 2
CH 3
CH 4
A
U
D
I
DC OUT
... 12V 200mA
REMOTE
O
COMPO-
NENT
COMPO-
SITE
O
U
T
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
1. Audio section
HEADPHONES
MIC POWER
CH1OFF
MIC POWER
CH2OFF
MIC POWER
CH3OFF
MIC POWER
CH4OFF
TC
IN
VIDEO
OUT
AUDIO
OUT
ON
ON
ON
ON
OUT
CAM
LINE
CAM
LINE
CAM
LINE
CAM
LINE
BREAKER
EARPHONE
-60
+4dB
-60
+4dB
-60
+4dB
-60
+4dB
VIDEO
OUT
1
2
PUSH
PUSH
PUSH
PUSH
CH 1
CH 2
CH 3
CH 4
PHONE
LEVEL
PHONE
A
U
D
I
SELECT
·
CH1 2
VIDEO IN
O
·
CH3 4
SUPER IMPOSE
I
N
OFF
ON
CAMERA
DC ... 12V 3A
DC IN
CH 1
CH 2
CH 3
CH 4
A
U
D
I
DC OUT
... 12V 200mA
REMOTE
O
COMPO-
NENT
COMPO-
SITE
O
U
T
1 HEADPHONES jack
6 MIC POWER switches
When a pair of stereo headphones (with an 8-ohm
impedance) are connected to this jack, the sound of
the recording or playback and the warning alarms
can be monitored through the headphones.
The sound to be monitored is set using the PHONE
SELECT switch.
These turn the power (+48V) for the phantom
microphones ON or OFF.
(The power can be switched to +12V using an
internal switch. For further details, consult your
dealer.)
7 Audio input selector switches
These are used to switch the audio inputs of the
four audio channels (CH1—CH4) individually.
CAM: Sound which is input from the CAMERA
connector.
2 EARPHONE jack
When earphones or a pair of stereo headphones
equipped with a mini plug are connected to this
jack, the sound of the recording or playback and the
warning alarms can be monitored through the
earphones.
LINE: Sound which is input from the AUDIO IN
connectors.
The sound to be monitored is set using the PHONE
SELECT switch.
8 Audio input level switches
These are used to switch the input level to –60 dBu
or +4 dBu to match the level of the sound which is
input from the AUDIO IN connectors. When the
switches have been set to the –60 dBu position, the
setting can be changed to –40 dBu using an
internal switch.
3 PHONE LEVEL control
This control is used to adjust the volume of the
sound which is output from the HEADPHONES jack
or EARPHONE jack.
4 PHONE SELECT switch
(For further details, consult your dealer.)
This is used to select the sound to be monitored at
the HEADPHONES jack or EARPHONE jack.
CH1/2: Sound of CH1 and CH2
9 AUDIO IN connectors (XLR 3-pin)
These are used to connect a microphone or
external device, and they enable the audio signals
of up to four channels to be input.
CH3/4: Sound of CH3 and CH4
5 AUDIO OUT connectors (PHONO)
The audio signals to be monitored are output
through these connectors. Whether PCM sound or
CUE sound is to be set as the audio output during
playback can selected using setup menu item No.
705.
: AUDIO OUT connectors (XLR 3-pin)
These are used to connect an external device, and
they enable the audio signals of up to four channels
to be output.
When PCM is selected, one of six kinds of channel
outputs can be selected using setup menu item No.
731.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
2. Video section
HEADPHONES
MIC POWER
CH1OFF
MIC POWER
CH2OFF
MIC POWER
CH3OFF
MIC POWER
CH4OFF
TC
VIDEO
OUT
AUDIO
OUT
ON
ON
ON
ON
IN
OUT
CAM
LINE
CAM
LINE
CAM
LINE
CAM
LINE
BREAKER
EARPHONE
-60
+4dB
-60
+4dB
-60
+4dB
-60
+4dB
VIDEO
OUT
1
2
PUSH
PUSH
PUSH
PUSH
CH 1
CH 2
CH 3
CH 4
PHONE
LEVEL
PHONE
SELECT
CH1 2
A
U
D
I
·
VIDEO IN
O
·
CH3 4
SUPER IMPOSE
I
N
OFF
ON
CAMERA
DC ... 12V 3A
DC IN
CH 1
CH 2
CH 3
CH 4
A
U
D
I
DC OUT
... 12V 200mA
REMOTE
O
COMPO-
NENT
COMPO-
SITE
O
U
T
1 CAMERA connector (26-pin)
5 VIDEO OUT 1, 2 connectors (BNC)
This is used to connect a camera equipped with a
multi connector.
The composite video signals are output from these
connectors.
It enables video signals, audio signals, control
signals and other signals to be sent to and from the
camera.
Power can also be supplied to the camera from the
unit.
When the SUPER IMPOSE switch is set to the ON
position, the VTR’s operating status or time code
will be superimposed onto the video signals which
are output from the VIDEO OUT 2 connector.
6 SUPER IMPOSE switch
When the video input selector switch is set to the
CAMERA position, the camera’s video signals are
input to the unit.
When this is set to ON, the VTR’s operating status
or time code will be superimposed onto the video
signals which are output from the VIDEO OUT 2
connector.
2 Video input selector switch
This is used to select the input video signals.
VIDEO IN:
Composite video signals from the device which has
been connected to the VIDEO IN connector.
CAMERA:
7 TC IN connector (BNC)
This connector is used for recording an external
time code onto the tape.
Component video signals or composite video
signals from the camera which has been connected
to the CAMERA connector.
8 TC OUT connector (BNC)
During playback, the playback time code is output
from this connector. During recording, the time
code which is generated by the internal time code
generator is output.
3 CAMERA input signal selector switch
This is used to select the input video signals from
the CAMERA connector 1.
9 VIDEO OUT connector (PHONO)
COMPONENT:Component video signals from the
camera
COMPOSITE: Composite video signals from the
camera
The composite video signals for monitoring
purposes are output from this connector.
<Note>
4 VIDEO IN connector (BNC)
The setup for the VIDEO IN and OUT connectors
and CAMERA connector can be processed using the
setup menu item No. 608 and 609 settings. (See
page 50)
The composite video signals are supplied to this
connector.
When the video input selector switch is set to the
VIDEO IN position, the video signals from the
device connected to the VIDEO IN connector are
input to the unit.
<Note>
When the unit is in the playback mode, supply
standard signals to this connector. The playback
output signals will then be synchronized with the
input signals.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
3. Power supply and other sections
HEADPHONES
MIC POWER
CH1OFF
MIC POWER
CH2OFF
MIC POWER
CH3OFF
MIC POWER
CH4OFF
TC
VIDEO
AUDIO
OUT
ON
ON
ON
ON
IN
OUT
OUT
CAM
LINE
CAM
LINE
CAM
LINE
CAM
LINE
BREAKER
EARPHONE
-60
+4dB
-60
+4dB
-60
+4dB
-60
+4dB
VIDEO
OUT
1
2
PUSH
PUSH
PUSH
PUSH
CH 1
CH 2
CH 3
CH 4
PHONE
LEVEL
PHONE
SELECT
CH1 2
A
U
D
I
·
VIDEO IN
O
·
CH3 4
SUPER IMPOSE
I
N
OFF
ON
CAMERA
DC ... 12V 3A
DC IN
CH 1
CH 2
CH 3
CH 4
A
U
D
I
DC OUT
... 12V 200mA
REMOTE
O
COMPO-
NENT
COMPO-
SITE
O
U
T
1 REMOTE connector (9-pin)
4 BREAKER button
When the dedicated external remote controller (AJ-
A95: optional accessory) is connected to this
connector, the unit can be operated from this
external controller.
This shuts off the power when a problem has
occurred.
As soon as the power is shut off, the BREAKER
button pops out.
<Note>
After checking the power connections, equipment
connections and battery, push the BREAKER
button back in. Power will be supplied if the
problem no longer exists.
This connector conforms to the RS-422A interface
standard but it does not support any editing
commands.
This unit does not have a phase-synchronizing
function so that when it is used as a simple source
VTR for editing applications, the phase
synchronization of the source VTR (player) should
be set to OFF for use.
If the power fails to be supplied even after the
BREAKER button has been pushed back in, consult
your dealer.
5 Battery compartment
The dedicated battery pack (AU-BP402: optional
accessory) is installed inside the compartment.
2 DC OUT socket
This is the DC 12V output socket.
It supplies power to the dedicated external remote
controller (AJ-A95). The DC power cable is
included with the AJ-A95.
3 DC IN socket
This is the DC 12V input socket.
Use the AC adapter (AJ-B75) available as an
optional accessory.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparations
<Note>
This unit must be placed either on a level surface or
upright for use.
It may not work properly if placed in any other
position.
Flat
Upright
Preparing to supply power
1. When using an AC adapter
DC IN connector
Use the dedicated AC adapter (AJ-B75: optional
accessory).
<Notes>
Switch off the unit’s power before using the AC
O
adaptor.
Connect the AC adapter’s power cord last of all.
O
POWER switch
Connect the AC adapter’s DC cable to the DC
IN socket on the unit.
1
2
3
Power switch
AC adapter
(AJ-B75)
Connect the AC adapter’s power cord, and set
its power switch to the ON position.
Set the POWER switch on the unit’s front panel
to ON.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparations
2. When using a battery pack
Use the dedicated battery pack (AU-BP402: optional
accessory). It is recommended that a spare battery
pack be kept on hand.
Open the cover of the battery compartment.
Check the battery level.
The battery level is displayed in the status display
window.
1
6
Cover
Battery level display
This indicates the remaining battery charge in
segments.
When all 7 segments light up, it means that the
battery has a full charge.
O
O
O
As the battery continues to discharge, the
segments go off one by one in sequence.
When the segment at the “E” (empty) end starts
flashing, the WARNING lamp also flashes, and
the warning alarm sounds intermittently, it
means that the battery will soon be fully
discharged.
Firmly insert the battery pack as far in as it will
go.
2
When all 7 segments flash, the WARNING lamp
remains lighted and the warning alarm sounds
continuously, it means that the battery is now
fully discharged.
O
<Note>
The warning alarm can be set using setup menu
items No. 900 and 901.
Battery pack
Battery voltage and segment display
(with AU-BP402)
Connect the plug, and stow any slack cord
away inside the compartment.
3
E
BATT
F
Over 12.5 V
12.35 V to 12.5 V
12.25 V to 12.35 V
12.2 V to 12.25 V
12.05 V to 12.2 V
11.85 V to 12.05 V
11.4 V to 11.85 V
Plug
Close the cover.
4
5
Set the POWER switch on the unit’s front panel
to ON.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparations
Preparing the cassette tape
Types of tapes and their recording
times
1. Concerning tapes
<Note>
M size cassettes
DV tapes bearing either the “
” or “
” logo for
50 Mbps mode
O
regular consumer applications cannot be used. Do
not insert them into the unit.
Tapes with a recording/playback length of up to
33 minutes:
25 Mbps mode
Tapes with a recording/playback length of up to
66 minutes:
O
Align the cassette with the center of the insertion slot,
and push it in gently.
Once inserted, the cassette tape is loaded
automatically.
AJ-P12MP, AJ-P24MP, AJ-P33MP, AJ-P46MP,
AJ-P66MP
L size cassettes
M
-cassette
50 Mbps mode
O
Caution:Do not insert S-cassette or with adaptor
Tapes with a recording/playback length of up to
92 minutes:
25 Mbps mode
O
Tapes with a recording/playback length of up to
184 minutes:
AJ-P34LP, AJ-P66LP, AJ-P94LP, AJ-P126LP,
AJ-5P92LP
For AJ-5P92LP cassette tapes recorded using
the DVCPRO (25 Mbps) mode, use a VTR
supporting DVCPRO (25 Mbps) 184 minute
tapes.
M size cassette
L size cassette
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparations
2. How to insert the cassette tape
Set the unit’s POWER switch to ON.
1
Status display window
Check the remaining tape.
The remaining tape time is indicated on the status
display window.
5
Remaining tape display
This indicates the remaining tape time in
POWER switch
segments.
When all 7 segments light up, it means that
there is more than 21 minutes of tape remaining.
(This can be changed to more than 30 minutes
using setup menu item No. 905.)
When the segment at the “E” (empty) end lights
up, it means that 3 minutes of the tape are left.
(This can be changed to 5 minutes using the
setup menu item No. 905.)
When the segment at the “E” (empty) end starts
flashing, it means that 2 minutes of the tape are
left. (This can be changed to 3 minutes using
the setup menu item No. 904.)
O
O
O
Check that the “HUMID” display is not
indicated on the status display window.
2
<Note>
If “HUMID” is indicated, keep the power on, and
wait until the indication is cleared.
Press the cassette insertion slot cover to open
it.
3
If this happens during recording, the WARNING
lamp flashes, and a warning alarm sounds
intermittently.
When all 7 segments flash, the WARNING lamp
remains lighted and the warning alarm sounds
continuously, it means that the tape has come to
its end.
O
<Notes>
The warning alarm is output from the PHONE
O
jack.
The warning alarm can be set using setup menu
items No. 902, 903 and 904.
O
Insert the cassette tape, and close the cassette
insertion slot cover.
4
Remaining tape and segment display
TAPE
E
F
M
-cassette
C
18 to 21 minutes (or over 30 minutes)
au
tio
n:
D
o
s
se
tt
e
o
r
w
ith
a
da
pt
or
15 to 18 minutes (or 25 to 30 minutes)
12 to 15 minutes (or 20 to 25 minutes)
D
ig
ita
l
V
id
eo
C
as
se
tt
e
9 to 12 minutes (or 15 to 20 minutes)
6 to 9 minutes (or 10 to 15 minutes)
3 to 6 minutes (or 5 to 10 minutes)
Under 3 minutes (or under 5 minutes)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparations
3. How to eject the cassette tape
Check that the unit’s power has been turned
on.
1
Press the cassette insertion slot cover to open
it.
2
Press the EJECT button.
The cassette tape is now ejected.
3
EJECT button
M
se
-cassette
C
au
tio
n:D
o
n
ot in
rt
S
-c
as
se
tt
e
o
r
w
ith
a
da
pt
or
Take out the cassette tape, and close the
cassette insertion slot cover.
4
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Preparing to record
1. Connecting the equipment
Connect the camera, VTR, video monitor and other
external devices.
Video monitor, VTR or other
unit with composite input
Microphone, tape recorder, etc.
HEADPHONES
EARPHONE
MIC POWER
CH1OFF
MIC POWER
CH2OFF
MIC POWER
CH3OFF
MIC POWER
CH4OFF
TC
VIDEO
OUT
AUDIO
OUT
Stereo headphones
Earphones
ON
ON
ON
ON
IN
OUT
CAM
LINE
CAM
LINE
CAM
LINE
CAM
LINE
BREAKER
-60
+4dB
-60
+4dB
-60
+4dB
-60
+4dB
VIDEO
OUT
1
2
PUSH
PUSH
PUSH
PUSH
CH 1
CH 2
CH 3
CH 4
PHONE
LEVEL
PHONE
SELECT
CH1 2
A
U
D
I
·
VIDEO IN
O
·
CH3 4
SUPER IMPOSE
I
N
OFF
ON
CAMERA
DC ... 12V 3A
DC IN
CH 1
CH 2
CH 3
CH 4
A
U
D
I
DC OUT
... 12V 200mA
REMOTE
O
COMPO-
NENT
COMPO-
SITE
O
U
T
Stereo amplifier or other
device for audio monitoring
Remote controller, etc.
VTR, camera or other unit
with composite output
Color video camera with
component output or
composite output
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
2. Setting the video inputs
Selecting the video input signals
The following three kinds of video signals can be
supplied to the unit.
Video input level display method
Whether the video input signals are being supplied
can be monitored on the level meter of the signal level
display window.
They are selected using the video input selector
switch and camera input selector switch.
<Note>
To select the composite video signals which are to
be supplied to the VIDEO IN connector, set the
video input selector switch to the VIDEO IN
position.
O
O
Check the video input level using 75% SMPTE color
bar signals. The level will not be displayed properly if
other video signals are used.
Signal level display window
<Note>
Bear in mind that stable recording may not be
possible if non-standard signals are supplied.
To select the signals which are to be supplied to the
CAMERA connector, set the video input selector
switch to the CAMERA position.
To select either component signals or composite
signals as the video signals supplied from the
camera, use the camera input selector switch.
Video input selector switch
VIDEO IN connector
Set the unit’s POWER switch to ON, and insert
a cassette tape on which signals can be
recorded.
1
The level meter now appears on the signal level
display window.
Press the METER button.
2
The level meter normally displays the audio level
but when the METER button is pressed, it displays
the input video signal level instead. When it is
pressed again, the audio level display is restored.
(Even when the input video signal level is
displayed, the audio level display will be
automatically restored in 5 seconds.)
Camera input selector switch
CAMERA connector
<Note>
The camera’s component signals are set to the
Betacam component level. To set them to the MII
level, first consult your dealer, and then set SW1 on
the VIDEO JACK circuit board (located inside the
connector panel) to the MII position.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
When component signals from the camera are
input
The Y, B-Y and R-Y signal levels are displayed in this
order from the left.
The B-Y and R-Y levels deflect up to the –10 dB scale
marking when 75 % SMPTE color bar signals are
input.
EMPHASIS
CH CONDI
0
0
10
10
20
20
30
40
30
40
-dB
-dB
Y
PB
PR
When composite signals from the camera are
input
The video signal Y level is displayed.
EMPHASIS
CH CONDI
0
0
10
10
20
20
30
40
30
40
-dB
-dB
Y
When signals are input to the VIDEO IN connector
The video signal level is displayed.
EMPHASIS
CH CONDI
0
0
10
10
20
20
30
40
30
40
-dB
-dB
VIDEO
<Notes>
The level displays above are indicated when 75 %
SMPTE color bar signals are supplied as the input
signals and the PB and PR level is 0.7 V [p-p]. The
display level drops by –20 dB when the signal level is
reduced by about 6 dB.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
3. Setting the audio inputs
Selecting the audio input signals
Set the unit’s POWER switch to ON, and insert
a cassette tape on which signals can be
recorded.
The level meter now appears on the signal level
display window.
1
The audio signals to be supplied to the unit are
selected using the audio input selector switch.
To select the audio signals to be supplied to the
AUDIO IN connector, set this switch to the LINE
position.
O
To select the audio signals to be supplied to the
CAMERA connector, set this switch to the CAM
position.
O
Select the audio input level selector switch to a
setting (–60 dBu or +4 dBu) that corresponds
with the input level.
2
3
Audio input selector switch
Set the UNI/VAR switch for the audio channel
to be adjusted to the UNI position.
The audio input level is displayed as it stands.
Set the UNI/VAR switch for the audio channel
to be adjusted to the VAR position.
4
5
CAMERA connector
AUDIO IN connector
While monitoring the level meter, adjust the
recording levels using the recording level
controls.
Adjusting the recording level
The audio levels of the audio signals supplied to the
unit can be adjusted and the signals recorded at those
levels.
Using the emphasis function
Emphasis can be added to the input signals and the
signals recorded with emphasis by means of the setup
menu item No. 704 setting.
6
appears on the audio level display when
emphasis has been added to the input signals.
EMPHASIS
(3)
1
3
4•5
2
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
4. Setting the time data
How to set the time code
Set the DISPLAY switch to the TC position.
1
2
<Note>
If both the user’s bit and time code are to be used, set
the user’s bit first.
Set the TCG selector switch to the SET
position.
If the time code is set first, the time code generator
will stop while the user’s bit is being set so that the
time code setting will be off. The range in which the
time code can be set extends from 00:00:00:00 to
23:59:59:29.
Select DF or NDF as the setup menu item No.
510 (DF MODE) setting.
3
DF: When the time code is to be advanced in
the drop frame mode
NDF: When the time code is to be advanced in
the non-drop frame mode
Set the time code using the SHIFT button as
well as the “+” and “–” buttons.
SHIFT button:
4
This causes the digit to be set to flash.
Each time it is pressed, the flashing digit
moves to the right.
1
2•5 4
“+” button:
This increases the flashing digit by 1.
“–” button:
This decreases the flashing digit by 1.
Set the TCG selector switch to the F-RUN or R-
RUN position.
5
F-RUN: When the time code is to be advanced
in the free run mode
R-RUN: When the time code is to be advanced
in the rec run mode
<Notes>
At the R-RUN position, the first recording to be
made after the time code has been set starts
from the value which was just set. However, if
the time code was not set, recording starts at
the value which continues on from the value
which is read out from the tape.
O
Select PRESET for the setup menu item No.
532 setting in order to prevent the time code
from continuing on from the value which is read
out from the tape when recording after the
cassette has been inserted or after the stop
mode has been established.
O
Concerning the time codes when the battery is
replaced
The backup mechanism is still operational even when
the battery is being replaced, and the time code
generator continues operating for an extended period
of time (approx. one year).
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
How set to the user’s bit
By setting the user’s bit, a memo (time or date) or
other information using up to 8 hexadecimal digits can
be recorded on the sub-code track.
Set the DISPLAY switch to the UB position.
1
2
Set the TCG selector switch to the SET
position.
Select USER as the setup menu item No. 530
(UB MODE) setting.
3
4
Set the user’s bit using the SHIFT button as
well as the “+” and “–” buttons.
SHIFT button:
1
2
4
This causes the digit to be set to flash.
Each time it is pressed, the flashing digit
moves to the right.
“+” button:
This increases the flashing digit by 1.
“–” button:
This decreases the flashing digit by 1.
A through F in hexadecimal notation are displayed as
shown in the table below.
O
Hexadecimal notation
Display
A
B
C
D
E
F
Concerning the user’s bit memory function
The user’s bit setting is automatically stored in the
memory and retained even when the unit’s power is
turned off.
<Note>
When TIME or DATE has been selected with the UB
MODE setting, the date or time which was set using
setup menu item No. 540 (TIME/DATE) is entered in
the user’s bit.
When TIME is selected, the hours, minutes and
O
seconds are entered in the user’s bit.
When DATE is selected, the year, month, day and
O
hours are entered in the user’s bit.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Procedure for locking to the external time code
<Note>
Once the operation to lock the time code to the
external time code has been performed, the time code
is instantly locked to the external time code, and the
same value as the external time code value is
displayed on the counter. Do not set the unit to the
recording mode for the several seconds it takes until
the time code stabilizes.
Concerning the user’s bit setting while the time
code is locked to the external time code
While the time code is locked to the external time
code, only the time data is locked to the time data of
the time code supplied from the external source.
This means that the user’s bit can be set separately
for each unit.
In order to lock the user’s bit to the user’s bit of the
time code supplied from the external source, set it to
the EXT mode which is set using setup menu item No.
530.
3
2
1
Set the unit’s POWER switch to ON.
1
2
Set the TCG selector switch to the F-RUN
position.
Set the DISPLAY switch to the TC position.
3
4
To release the time code from being locked to the
external time code
First stop supplying the external time code, and then
Supply the reference time code and reference
video signals whose phase correlation meets
the time code standard to the TC IN connector
and VIDEO IN connector, respectively.
set the TCG selector switch to the R-RUN position.
When switching the power supply from the battery
to AC adaptor while the time code is locked to the
external time code
In order to ensure that the time code generator’s
power supply remains uninterrupted, first connect the
AC adaptor to the DC IN socket, and then disconnect
the battery pack. If the battery pack is disconnected
first, no guarantees can be made for the continuity of
the locking to the external time code.
When connecting two or more AJ-D92 units and
locking the time code
Set the TCG selector switch on each AJ-D92 unit to
the F-RUN position.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Locking the time code to the external time
code
The unit’s time code generator can be locked to an
external time code generator.
Example of connections used for locking to an external time code
REF IN
Reference signal
Time code generator
REF OUT
First AJ-D92 unit
TC IN
TC IN
TC IN
GENLOCK IN
TC OUT
Camera
Second AJ-D92 unit
GENLOCK IN
TC OUT
Camera
Third AJ-D92 unit
GENLOCK IN
Camera
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Recording Operations
Press the unit’s STOP button when recording is
to be ended.
4
1. Recording using the CAMERA
connector
<Notes>
If the signals (component video signals or
O
composite video signals) selected using the
CAMERA input signal selector switch are not
supplied to the CAMERA connector, the
mismatching detector circuit is activated, the unit is
set to the REC PAUSE mode, and recording is not
commenced.
The detector circuit is activated and the unit is set
to the REC PAUSE mode also when the signals are
interrupted during recording.
When the signals are restored, recording will
automatically recommence.
O
1
4 2
3
When the detector circuit is activated in the above
way and the REC PAUSE mode is established, error
code [E-A0] and the time data will be displayed
alternately in the status display window.
However, recording will only be continued if ON has been
selected as the setup menu item No. 130 (NO VIDEO REC)
setting.
In this case, input signal error is indicated by the warning
lamp and alarm.
Set the video input selector switch to the
CAMERA position.
1
Press the REC button and PLAY button at the
same time.
The unit is now set to the standby mode.
2
<Note>
Since recording will start immediately at this point if
the camera’s VTR start/stop button is at the start
setting, make sure that the button is at the stop
setting.
Press the camera’s VTR start/stop button to
start recording.
When the REC lamp inside the viewfinder stops
flashing and lights, recording is commenced.
<Note>
3
The frame-to-frame continuity mode is established
when the VTR start/stop operations are performed
at the camera. (This mode can be changed using
setup menu item No. 110.)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
2. Recording using the VIDEO IN
connector
3. To stop the recording temporarily
1
1•2
(1•2)
Set the video input selector switch to the
VIDEO IN position.
1
Press the unit’s PAUSE/STILL button or
camera’s VTR start/stop button.
The unit is set to the REC PAUSE mode, and the
1
Press the REC button and PLAY button at the
same time.
Recording now starts.
PAUSE/STILL lamp flashes.
2
To end the recording, press the unit’s
PAUSE/STILL button or camera’s VTR
start/stop button.
2
Press the unit’s STOP button when recording is
to be ended.
3
<Notes>
When recording was commenced using the
camera’s VTR start/stop button, the operation
cannot be temporarily stopped using the unit’s
PAUSE/STILL button.
When the REC PAUSE mode continues, the unit
will reverse the tape for several frames every 2
minutes to protect the cylinder heads and tape.
When the REC PAUSE mode has continued for 30
minutes, the tape is unloaded, the standby OFF
(half-loading) mode is established, and the
CASSETTE IN lamp flashes.
O
<Notes>
If the video signals are not supplied to the VIDEO
IN connector, the mismatching detector circuit is
activated, the unit is set to the REC PAUSE mode,
and recording is not commenced.
O
O
The detector circuit is activated and the unit is set
to the REC PAUSE mode also when the signals are
interrupted during recording.
O
When the signals are restored, recording will
automatically recommence.
(The frame-to-frame continuity mode can be
changed using setup menu item No. 110.)
When the detector circuit is activated in the above
way and the REC PAUSE mode is established, error
code [E-A0] and the time data will be displayed
alternately in the status display window.
However, recording will only be continued if ON has been
selected as the setup menu item No. 130 (NO VIDEO REC)
setting.
In this case, input signal error is indicated by the warning
lamp and alarm.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
4. REC REVIEW function
This function serves to play back the part of the tape
immediately before the end of the recording to check
whether the recording was executed properly.
In the playback mode, search for the break in
the video recording, and press the STOP
button within 1 to 2 seconds.
1
2
Press the REC button and PAUSE/STILL button
at the same time.
After the tape is rewound to the break in the video
recording, the tape is further rewound by the auto
back function, and the unit is set to the REC
PAUSE mode.
Press the PAUSE/STILL button to start
recording.
When recording is started, the tape begins its
approach, and recording with frame-to-frame
continuity can be conducted.
3
1
Press the REC REVIEW button in the REC
1
PAUSE mode.
The tape is rewound at approximately –1a normal
speed while the REC REVIEW button is held
down.
The tape is rewound for a minimum of 2 or so
seconds and a maximum of 10 or so seconds.
When the REC REVIEW button is released,
playback automatically starts from the point where
the button was released until the REC PAUSE
position, and the REC PAUSE mode is
established.
<Note>
It is recommended that REC be selected as the setup
menu item No. 105 setting to transfer to the recording
mode more quickly.
6. Preventing erroneous recording
operations
<Note>
When the temporary stop mode has been released
during a REC REVIEW operation, the REC command
is accepted but recording starts after the tape is
rewound to the frame-to-frame continuity point.
During recording, the unit will not respond to the
pressing of any of the function buttons except
STOP and PAUSE/STILL. (This is to prevent the
transfer to another mode during recording.)
When the KEY INHIBIT switch is set to ON, all the
function buttons except for the ones set using setup
menu item No. 000 will no longer work.
O
O
5. Auto back function
Under the initial settings, none of the function
buttons except for STOP and EJECT will work.
When ENA has been selected as the setup menu
item No. 000 setting, all the function buttons are
made operable.
In order to ensure frame-to-frame continuity, this
function automatically rewinds the tape for
approximately 1 second after REC PAUSE and stops
the tape.
When recording is to be resumed, the tape begins its
approach and after it is completely on-track, recording
is resumed. In this way, continuous recording free
from disruptions can be ensured.
To initiate frame-to-frame continuity after a break
has been searched for in the playback mode
1
2 3
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Preparing for playback
1. Selecting the sound to be
monitored
2. Playback in synchronization with
the external signals
VIDEO IN connector
1
2
Video input selector switch
Use the PHONE SELECT switch to set the
1
Connect the external signal, to which playback is to be
synchronized, to the VIDEO IN connector, and set the
video input selector switch to the VIDEO IN position.
Playback is now initiated in synchronization with the
signal which is connected to the VIDEO IN connector.
<Notes>
sound which is to be monitored during
playback at the HEADPHONES jack and
EARPHONE jack.
CH 1/2: Sound of CH1 and CH2
CH 3/4: Sound of CH3 and CH4
If the VIDEO IN connector’s signal is disconnected
and re-connected during playback, the playback
picture may be disturbed.
It is recommended that a signal complying with the
RS-170A standard be used as the reference signal
for playback.
O
Use the PHONE LEVEL control to adjust the
output audio level.
2
O
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
<Notes>
Playback Operations
The PLAY PAUSE mode retention time can be set
O
using setup menu item No. 400. When HALF has
been selected as the setup menu item No. 401
setting, the tape is unloaded, and the standby OFF
(half-loading) mode is established.
1. Playback at the regular speed
and still-picture playback
Noise may appear on the still picture when the
PAUSE/STILL button is pressed during playback.
A still picture can be shown on the monitor in the
STOP mode by selecting PB as the setup menu
item No. 105 setting.
O
O
1
When the unit is used as a player, the playback
picture can be made to appear more quickly by
selecting PB as the setup menu item No. 105
setting.
It is recommended that PB be selected as the setup
menu item No. 105 setting even when it is to be
used as the source unit during editing.
4 2
3
1
Set the unit’s POWER switch to ON, and insert
a cassette tape with signals already recorded
on it.
1
2
If REC is selected, it may take some moments to
achieve phase synchronization.
Press the PLAY button.
The recorded pictures and sound will now be
played back.
Use the PB LEVEL controls to adjust the
playback output level of the sound.
3
4
Press the unit’s STOP button to end the
playback.
Temporarily stopping the playback
Press the PAUSE/STILL button during playback.
The PAUSE/STILL lamp flashes, the picture shown on
the monitor is frozen, and the PLAY PAUSE mode is
established.
Playback is resumed when the PAUSE/STILL button
is pressed again.
When the PLAY PAUSE mode continues for 2
minutes, the unit will forward the tape for several
frames to protect the cylinder heads and tape, and the
STILL mode is established again.
When the STILL mode has continued for over 30
minutes, the standby OFF (half-loading) mode is
automatically established in order to protect the tape.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
2. Cue playback and review
playback
VTR operating
mode
Transfer of VTR
operation
Function button
SEARCH
FF or REW
PLAY or STOP
SEARCH
PLAY or STOP
SEARCH
PLAY or STOP
FF
Search still
When the FF button or REW button is pressed in one
of the search modes (search still, FWD search, REV
search, FWD search still or REV search still), the tape
is cued or reviewed at the speed which was selected
for the setup menu item No. 100 setting.
Further, if the SEARCH button is pressed in the FF
mode or REW mode, the tape is cued or reviewed at a
reduced speed, namely, at the speed selected for the
setup menu item No. 100 setting.
When the PAUSE/STILL button is pressed during cue
or review playback, the tape will be temporarily
stopped.
When it is pressed again, cue or review playback is
resumed.
PLAY or STOP
FF or REW
PLAY or STOP
FF
FWD search
(cue playback)
PLAY or STOP
REW
REV search
(review playback)
PLAY or STOP
FWD search
(cue playback)
Search still
REV search
(review playback)
REW
SEARCH
REW
FF
FWD search
(cue playback)
REV search
(review playback)
PAUSE/STILL
SEARCH
FF
FWD search still
REW
REV search
(review playback)
FWD search
(cue playback)
PAUSE/STILL
REV search still
PAUSE/STILL,
SEARCH or FF
FWD search
(cue playback)
FWD search still
REV search
(review playback)
REW
PAUSE/STILL,
REV search
SEARCH or REW
(review playback)
REV search still
Any mode
FWD search
(cue playback)
FF
PLAY
STOP
PLAY
STOP
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
4. Variable speed playback
a
3. Linear 0.3 speed playback
(When AJ-A95 is connected)
The slow still mode is established when the SEARCH
button is pressed during still-picture playback (PLAY
PAUSE).
Linear 0.3a speed playback is performed by pressing
the FF or REW button in this mode.
When the PAUSE/STILL button is pressed during the
linear 0.3a speed playback, the tape is temporarily
stopped.
Linear 0.3a speed playback is restored when the
PAUSE/STILL button is pressed again.
<Note>
When the optional AJ-A95 remote controller is
connected to the REMOTE connector, variable speed
playback is enabled by operating the search dial on
the AJ-A95.
<Notes>
Noise appears on the screen during playback at
any tape speed except the normal tape speed (1a).
During variable speed playback, the sound
recorded on the analog cue track is played back.
O
O
Noise appears during linear 0.3a speed playback.
VTR operating
mode
Transfer of VTR
operation
Function button
PAUSE/STILL
PLAY
PLAY PAUSE
PLAY
PAUSE/STILL or
PLAY
PLAY PAUSE
Slow still
SEARCH
PLAY
FF
Slow still
PLAY
FWD slow
REV slow
REV slow
FWD slow still
FWD slow
REV slow still
REW
REW
FWD slow
REV slow
SEARCH or
PAUSE/STILL
FF
SEARCH or
PAUSE/STILL
PAUSE/STILL,
SEARCH or FF
FWD slow
REV slow
REV slow
FWD slow still
REV slow still
REW
PAUSE/STILL,
SEARCH or REW
FF
FWD slow
PLAY
STOP
FF
PLAY
STOP
Any mode
Any mode
STOP
STOP
FF
REW
REW
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
5. Reading and displaying the time
data
Displaying the time data on the monitor
screen
The recorded time code and user’s bit are read by the
built-in time code reader during tape playback.
The time data which is read out can be displayed on
the status display window or monitor screen.
When the time data is displayed in the status display
window, connect the monitor’s input connector to the
VIDEO OUT 2 connector, and set the SUPER
IMPOSE switch to ON.
The time data will now be displayed on the monitor
screen.
Displaying the time data on the status
display window
The time data to be displayed is selected by the TCG
selector switch and DISPLAY switch positions.
What time data is to be displayed is determined in two
stages: first by the position selected by the TCG
selector switch, and second by the position of the
DISPLAY switch.
VIDEO OUT 2 connector
Status display window
SUPER IMPOSE switch
Outputting the playback time code from
the TC OUT connector
When the unit is in the playback mode, the playback
time code is output.
TCG selector switch
DISPLAY switch
TC OUT connector
TCG selector
switch position
DISPLAY switch
position
Data displayed
Time code
User’s bit
CTL
TC or CTL
UB
SET
CTL
F-RUN or R-RUN
TC
Time code
User’s bit
UB
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Superimposed Screens
When the unit’s VIDEO OUT 2 connector has been
connected to a TV monitor, the control signals, time
codes, etc. can be displayed as abbreviations on the
TV monitor screen.
Display characters
The background of the superimposed display
characters can be changed by setting setup menu
item No. 006 (CHARA TYPE).
This display can be set to ON or OFF using the
SUPER IMPOSE switch.
(See page 45)
TV monitor
No display:
Normally, no display.
P: Flashes when the DC
supply voltage has
dropped.
TV monitor
TV monitor
L: Flashes in “LOW RF”
status.
N: Flashes in “NO RF”
status.
Display position
Abbreviations
CTL (control signal)
TCG (time code generator value)
TCR (playback value of time code)
UBG (user’s bit generator value)
UBR (playback value of user’s bit)
The position of the superimposed display can be
changed by setting setup menu items No. 004
(CHARA H-POS) and No. 005 (CHARA-V.POS).
(See page 45)
<Notes>
The colon between the seconds and frames
changes to a period when a drop frame time code
is being read. The same time code also appears
on the status display window, and the operating
status display “DF” is indicated.
O
When the time code signal is missing, it is
automatically interpolated by the CTL signal.
O
TV monitor
TV monitor
<Notes>
The following appears on the display.
When the PAGE button and DATA+ button or DATA–
button are pressed, the counter display appears
temporarily on the TV monitor while these buttons are
held down to enable the setting to be checked.
T
R
00 : 07 : 04 : 24
Even while the PAGE button is pressed, the settings
can be performed using the DATA+ button or DATA–
button while the actual status is checked.
The colon between the seconds and frames
changes to a period when a drop frame is
read.
An asterisk ( ) appears when the
time code signal is missing.
(For superimposing only)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Superimposed Screens
Operation modes
<Notes>
When the beginning or end of the tape has been
What is to be displayed on the screen can be selected
by setting setup menu item No. 003 (DISPLAY SEL).
(See page 45)
O
detected in the VTR operation mode, BOT
(beginning of tape) or EOT (end of tape) is
displayed at the beginning of the line.
Examples of what is displayed:
EOT STOP
TIME: Counter value
T&STA: Counter value, VTR operation mode
T&R:
Counter value, amount of remaining tape
T&S&R: Counter value, VTR operation mode,
(stop mode at end of tape)
amount of remaining tape
BOT STANDBY OFF
(standby mode at beginning of tape)
In the T&S&R mode, one of the following error
displays appears on the third line (line where the
amount of remaining tape is displayed).
[NO RF]:
O
TIME mode
This appears when a blank section has been
detected on the tape.
Counter value
At the same time, error code “E-09” and the
warning display “RF” appear on the status
display window.
TV monitor
[SERVO NOT LOCKED]:
This appears when the servo is not locked.
At the same time, error code “E-00” and the
warning display “SERVO” appear on the status
display window.
T&STA mode
[LOW RF]:
This appears when there is no head output.
At the same time, error code “E-01” and the
warning display “RF” appear on the status
display window.
Counter value
VTR operation mode
TV monitor
[HIGH ERROR RATE]:
This appears when the error rate has
deteriorated (when the 3 channel condition
indicators are lighted).
T&R mode
At the same time, error code “E-02” and the
warning display “RF” appear on the status
display window.
Counter value
Amount of remaining tape
TV monitor
T&S&R mode
Counter value
VTR operation mode
Amount of remaining tape
TV monitor
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (Initial Settings)
The unit’s main settings can be performed and
checked using the on-screen menus which are
displayed on the video monitor connected to the unit.
It is also possible to perform and check the settings
using the item numbers and setting numbers which
appear on the front panel’s display status area.
Two user setting memories are provided. The desired
settings can be stored in these memories in advance
for use during operation.
Press the MENU-UP button or MENU-DOWN
button to move the cursor ( ) to the menu
item whose setting is to be changed.
The page can be scrolled up or down by pressing
the MENU-UP button or MENU-DOWN button
while holding down the PAGE button.
4
Press the DATA+ button or DATA– button to
change the setting.
5
6
Setting method using on-screen
menus
Press the SET button to enter the setting.
To change more than one item on the menu,
repeat steps 4, 5 and 6 for each item.
<Note>
The setting can be canceled by pressing the
MODE button.
When other items are to be changed without the
setting having been entered, press the MODE
button and then proceed with steps 4, 5 and 6.
Set the MENU switch to the ON position.
1
The unit is now set to the menu setting mode,
and the menu screen appears on the video
monitor.
SETUP–MENU
MAIN
NO.000
000 BASIC
Set the MENU switch to the OFF position.
This completes the menu settings.
100 OPERATION
200 INTERFACE
400 TAPE PROTECT
500 TIME CODE
600 VIDEO
7
700 AUDIO
900 WARNING&ALARM
END
In the menu setting mode, the REW, FF,
SEARCH, STOP, PLAY, REC and PAUSE/STILL
function buttons serve as the PAGE, MENU-
DOWN, MENU-UP, MODE, DATA–, DATA+ and
SET buttons, respectively.
Press the MENU-UP button or MENU-DOWN
button to move the cursor ( ) to the menu
whose settings are to be changed.
2
3
Press the MODE button to set each item in
turn.
To return to the menu screen, press the MODE
button while holding down the PAGE button.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (Initial Settings)
How to set the time/date
How to return to the factory
settings
Set the unit to the menu setting mode, and
move the cursor ( ) to 540.
1
Set the MENU switch to the ON position.
1
The unit is now set to the menu setting mode,
and the menu screen appears on the video
monitor.
Press the MODE button, and move the cursor
to the TIME/DATE setting screen.
To return to the menu screen, press the MODE
2
button while holding down the PAGE button.
Press the RESET button.
2
The unit is set to the default setting mode, and
the default setting screen appears on the video
monitor.
Set the date and time.
3
4
SELECT
MODE
0 ESCAPE
1 LOAD
2 SAVE
3 PROTECT
Move the cursor to No. 05 and press the SET
button.
The screen for checking the settings now
appears.
TIME/DATE SET OK?
NO
YES
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the LOAD
position, and press the SET button.
3
The unit is set to the LOAD mode, and the load
screen appears on the video monitor.
Press the MENU-UP button, set the cursor to
5
the YES position, and press the SET button.
As soon as the SET button is pressed, the date
and time are entered, and the menu screen is
restored.
SET–UP MENU
NO
<LOAD>
If the cursor was moved to NO instead and the
SET button pressed, the menu screen is
restored without the date and time having been
entered.
O
FACTORY
USER <1>
USER <2>
Press the MENU-UP button or MENU-DOWN
button to move the cursor to FACTORY, and
press the SET button.
4
5
When this operation is performed with the
cursor moved to FACTORY, the factory
settings will be restored.
O
When this operation is performed with the
cursor moved to NO instead, the factory
settings are not restored, and operation is
returned to the menu screen.
O
Set the MENU switch to the OFF position.
This completes the menu settings.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (Initial Settings)
How to set the user default
settings
SAVE OK?
NO
YES
Set the MENU switch to the ON position.
1
Set the MENU switch to the OFF position.
This completes the menu settings.
7
The unit is now set to the menu setting mode,
and the menu screen appears on the video
monitor.
How to load the user settings
2
3
Perform steps 2 through 6 of “Setting
method using on-screen menus” to change
the items to the desired settings.
(See page 40)
Set the MENU switch to the SET position.
1
The unit is now set to the menu setting mode,
and the menu screen appears on the video
monitor.
Press the RESET button.
The unit is set to the default setting mode, and
the default setting screen appears on the video
monitor.
Press the RESET button.
2
The unit is set to the default setting mode, and
the default setting screen appears on the video
monitor.
SELECT
MODE
0 ESCAPE
1 LOAD
2 SAVE
SELECT
MODE
0 ESCAPE
1 LOAD
3 PROTECT
2 SAVE
3 PROTECT
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the SAVE
position, and press the SET button.
The unit is set to the SAVE mode, and the save
screen appears on the video monitor.
4
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the LOAD
position, and press the SET button.
3
The unit is set to the LOAD mode, and the load
screen appears on the video monitor.
SET–UP MENU
NO
<SAVE>
SET–UP MENU
NO
<LOAD>
USER <1>
USER <2>
FACTORY
USER <1>
USER <2>
Press the MENU-UP button or MENU-DOWN
button to move the cursor to USER1 or
USER2, and press the SET button.
5
6
If this operation is performed with the cursor
moved to NO instead, the settings are not
updated, and operation is returned to the menu
screen.
O
Press the MENU-UP button or MENU-DOWN
button to move the cursor to USER1 or
USER2, and press the SET button.
4
5
If this operation is performed with the cursor
moved to NO instead, no change is made to
the user settings saved in the memory, and
operation is returned to the menu screen.
O
The screen for checking the SAVE operation
appears. Press the MENU-UP button or
MENU-DOWN button to move the cursor to
the YES position, and press the SET button.
The settings are now saved in the memory.
Set the MENU switch to the OFF position.
This completes the menu settings.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (Initial Settings)
How to protect the menus
Set the MENU switch to the OFF position.
The unit is set to the menu protect mode.
Now, even if the MENU switch is set to the SET
position, the menu setting mode will not be
established, and “MENU PROTECTED” will
appear on the video monitor screen.
5
Opening the setup menus can be prevented even
when the MENU switch on the front panel is set to the
SET position by setting the unit to the menu protect
mode.
<Note>
Set the MENU switch to the SET position.
1
If, during the menu protect mode setting, the
MENU switch is set to the SET position while
holding down the METER button on the front
panel, the menu setting mode will be established
and the regular menu settings can be performed.
Perform steps 2 through 7 of “Setting method
using on-screen menus.”
The unit is now set to the menu setting mode,
and the menu screen appears on the video
monitor.
Press the RESET button.
2
The unit is set to the default setting mode, and
the default setting screen appears on the video
monitor.
(See page 40)
SELECT
MODE
How to release the menu
protection
0 ESCAPE
1 LOAD
2 SAVE
3 PROTECT
Set the MENU switch to the SET position
while holding down the METER button on the
front panel.
1
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the PROTECT
position, and press the SET button.
The unit is set to the menu protect setting mode,
and a screen for verifying whether to protect the
setup menus appears on the video monitor.
3
4
The unit is set to the menu setting mode, and the
menu screen appears on the video monitor.
2
3
Perform steps 2 and 3 of “How to protect the
menus” above.
The screen for verifying whether to protect the
MENU PROTECT OK?
NO
YES
setup menus appears on the video monitor.
MENU PROTECT OK?
NO
YES
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the YES
position, and press the SET button.
The menu screen is now displayed.
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the NO position,
and press the SET button.
The menu protection is now released.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (Initial Settings)
How to display the DIAG menu
This unit has a function for displaying an hours meter
and software version on the video monitor.
Set the MENU switch to the ON position while
holding down the EJECT button.
The unit is set to the diagnosis display mode, and
1
“HOURS METER” appears on the video monitor.
DIAG–MENU
HOURS METER
Ser
H00 OPERATION
H01 DRUM RUN
H02 TAPE RUN
H03 THREADING
H11 DRUM RUN r
H12 TAPE RUN r
H13 THREADING r
END
00000H
00000H
00000H
00000T
00000H
00000H
00000T
Any item with “r” can be reset when servicing is
performed.
While the hours meters screen is displayed,
press the MENU-UP button or MENU-DOWN
button while holding down the PAGE button.
The software version is displayed on the video
monitor.
2
3
DIAG–MENU VERSION
<NTSC>
IF
1.
-
-
-
-
-
- .
- .
- .
- .
- .
AV-SYSCON 1.
DV
CYLINDER
REEL
END
1.
1.
1.
When the MENU-UP button or MENU-DOWN
button is pressed again while holding down the
PAGE button, operation returns to the hours
meter display.
Set the MENU switch to the OFF position.
Operation now returns to the normal mode.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
BASIC menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
000 KEY-INH SEL
For setting the switches which can still be operated on the front panel when
the KEY INHIBIT switch has been set to ON.
0000
0001
0002
DIS 0: None of the switches can be operated.
ST&EJ 1: Only the STOP and EJECT switches can be operated.
ENA 2: All the switches can be operated.
003 DISPLAY SEL
For setting what is to be displayed by superimposing onto the video monitor
output.
0000
0001
0002
0003
TIME 0: Only the time is displayed.
T&STA 1: The time and operation status are displayed.
T&R 2: The time and amount of remaining tape are displayed.
T&S&R 3: The time, operation status and amount of remaining tape are displayed.
004 CHARA H-POS
0000
0 For setting the character position in the horizontal direction for the
superimposed display.
4
0004
0008
0013
8
005 CHARA V-POS
006 CHARA TYPE
007 SYS FORMAT
13 For setting the character position in the vertical direction for the
superimposed display.
22
0022
For setting the type of superimposed display and menu display.
WHITE 0: White characters are displayed on a black background.
W/OUT 1: White characters with black borders are displayed.
0000
0001
For setting the unit’s recording and playback format.
50M 0: 50 Mbps mode
25M 1: 25 Mbps mode
0000
0001
<Note>
When the 25 Mbps mode is set, the sound is recorded and played back on
two channels (CH1 and CH2).
008 PB FORMAT
For setting the format during tape playback.
MANUAL 0: The format is based on the setting selected for menu item No. 007 (SYS
FORMAT).
0000
0001
AUTO 1: The format recorded on the tape is used.
030 AUDIO P.SAVE
For setting the power save mode during recording.
ALLON 0: The audio outputs of all four channels (CH1, CH2, CH3 and CH4) are
temporarily suspended.
3/4ON 1: The audio outputs of two channels (CH3 and CH4) are temporarily
suspended.
0000
0001
0002
OFF 2: All the sound is output.
The underlining indicates the factory setting.
<Notes>
If the PAGE button and DATA+ button or DATA– button are pressed when the CHARA H-POS or CHARA
V-POS item has been set, the counter display appears temporarily while these buttons are held down to
enable the setting to be checked.
Even while the PAGE button is pressed, the settings can be performed using the DATA+ button or DATA–
button while the actual status is checked.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
OPERATION menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
100 SEARCH SPEED
101 SHTL MAX
For setting the speed at which the tape is to be decelerated when the
search switch on the front panel has been pressed.
0: 4.1a normal tape speed
X4.1
0000
0001
1: 8.4a normal tape speed
X8.4
For setting the maximum speed in the shuttle mode when the external
controller connected to the 9-pin remote connector is used.
0: 8.4a normal tape speed
1: 16a normal tape speed
2: 32a normal tape speed
0000
0001
0002
X8.4
X16
X32
102 FF. REW MAX
For setting the maximum fast forward and rewind speed.
1: 16a normal tape speed
2: 32a normal tape speed
0000
0001
0002
X16
X32
X60
3: 60a normal tape speed
<Note>
When the 50 Mbps mode has been selected as the menu item No. 007
(SYS FORMAT) setting, the tape will run at 32a the normal tape speed
even if 60a has been selected.
105 STOP MODE
106 HUMID OPE
For setting the mode of the digital circuit in the stop mode.
REC 0: The digital circuit serves as the REC circuit. It takes a shorter time for
operation to transfer to the REC mode.
At this point, the E-E mode is established.
PB 1: The digital circuit serves as the PB circuit. It takes a shorter time for
operation to transfer to the playback mode.
0000
0001
For setting whether to ignore condensation when it has formed and
continue with operation.
0000
0001
OFF 0: Unit does not continue to operate when condensation has formed.
ON 1: Unit continues to operate when condensation has formed, in which case
it cannot be guaranteed that the unit will operate normally.
<Note>
Since the tape may be damaged with a “1” setting, this item should normally
be set to 0 (no operation).
107 WIDE MODE
110 AUTO BACK
For setting whether to perform recording in the wide mode.
WIDE 0: Recording is performed in the wide mode.
NORMAL 1: Recording is performed in the 4:3 normal mode.
0000
0001
For setting the operation method of the frame-to-frame continuity function
(for setting the operation of the auto back function for rewinding the tape for
several seconds in order to eliminate disturbances in the recorded pictures).
OFF 0: Auto back function is disabled (no continuity between frames).
REC-P 1: In the REC PAUSE mode, the auto back function is activated to ensure
frame-to-frame continuity.
0000
0001
0002
ALL 2: Regardless of the VTR mode, the auto back function is activated to
ensure frame-to-frame continuity.
111 AFTER CUE-UP
113 BATTERY SEL
For setting the status after cue-up.
STOP 0: For stopping the tape in the stop mode.
STILL 1: For stopping the tape in the still mode.
0000
0001
For setting the type of battery.
0000
BP402 0: AU-BP402 (made by Matsushita Electric Industrial), 12 V nickel-cadmium
battery
0001
0002
0003
0004
BPH90 1: BP-H90 (made by IDX), 12 V nickel-hydrogen battery
BPH100 2: BP-H10C (made by IDX), 13 V nickel-hydrogen battery
HP90 3: HP-H90 (made by PACO), 13 V nickel-hydrogen battery
HP90A 4: HP-H90A (made by PACO), 13 V nickel-hydrogen battery
The underlining indicates the factory setting.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
OPERATION menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
128 BATT WARNING
For setting the voltage at which a warning is given when the battery is
nearly discharged.
0000
0001
AUTO 0: The voltage is set by the battery which was set in setup menu item No.
113 (BATTERY SEL).
AU-BP402 : 11.4 V
BP-H90 :
11.0 V
BP-H100 : 11.6 V
HP-90 :
HP-90A :
12.0 V
11.4 V
MANUAL 1: The voltage setting can be changed to match the battery used. The
change made to the setting is saved.
Press the MODE button, and change the setting using the “00: BATT
NEAR END” menu.
00 BATT NEAR
END
10.7
14.0
10.7V For changing in 0.1 V increments the voltage setting at which a warning is
given when the battery is nearly discharged to match the battery used.
Initial voltage setting:
14.0V O
AU-BP402 : 11.2 V
BP-H90 :
10.9 V
BP-H100 : 11.6 V
HP-90 :
HP-90A :
12.0 V
11.4 V
129 BATT DISPLAY
For setting whether to display the battery voltage on the status display
window when the METER button is pressed.
0000
0001
OFF 0: The voltage is not displayed in the status display window.
ON 1: The voltage is displayed in the status display window.
Example of display shown: 11.2 V
O
130 NO-VIDEO REC
131 LIGHT SET UP
132 26PIN REC
For setting whether to proceed with recording when no video signals are
input.
OFF 0: Recording is disabled. When the video signals are no longer input during
recording, operation is transferred to the REC PAUSE mode.
ON 1: Recording is enabled.
0000
0001
For setting whether LCD backlight illumination status is to be stored in the
memory when the power is switched off.
OFF 0: Status is not stored. When the power is turned back on, the backlight
illumination will always be off.
0000
0001
ON 1: Status is stored.
For setting whether to acknowledge the REC command when the camera’s
START/STOP button is used for control while connection is made to the
CAMERA connector (26 pins).
0000
0001
ALL 0: The REC command is acknowledged regardless of the VTR mode.
REC-P 1: The REC command is acknowledged only when the REC PAUSE mode
is established.
The underlining indicates the factory setting.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
INTERFACE menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
200 ID SEL
For setting the ID information to be returned to the controller.
0000
0001
OTHER 0: 20 25H is returned.
DVCPRO 1: The DVCPRO unit’s own ID (F0 33H) is returned.
The underlining indicates the factory setting.
TAPE PROTECT menu
Item
Setting
Description of setting
Superimposed
display
Superimposed
display
No.
No.
400 STILL TIMER
0000
0001
0002
0003
0004
0005
0006
0007
0008
0.5S For setting the time taken until the tape protection mode is established
5S when the unit has been left standing in the stop or still mode.
10S (Unit: S = seconds, min = minutes)
20S
30S
40S
50S
1min
2min
401 SRC PROTECT
For setting the tape protection mode operation when the unit has been left
standing in the still mode.
0000
0001
STEP 0: STEP FWD
HALF 1: STANDBY OFF (HALF LOADING)
<Note>
If STEP FWD has been selected, the unit is automatically transferred to the
STANDBY OFF (HALF LOADING) mode when the total length of time it has
been left standing in the still mode reaches 30 minutes.
402 DRUM STDBY
For setting the drum operation in the STANDBY OFF (HALF LOADING)
mode.
0000
0001
OFF 0: The drum rotation is stopped.
ON 1: The drum rotation is continued.
403 STOP PROTECT
For setting the tape protection mode operation when the unit has been left
standing in the stop mode.
0000
0001
STEP 0: STEP FWD
HALF 1: STANDBY OFF (HALF LOADING)
<Note>
If STEP FWD has been selected, the unit is automatically transferred to the
STANDBY OFF (HALF LOADING) mode when the total length of time it has
been left standing in the still mode reaches 30 minutes.
The underlining indicates the factory setting.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
TIME CODE menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
509 TCG CF FLAG
For setting whether to add the CF flag of the TCG to the CF bit (color frame
bit) of the TCG.
0000
0001
OFF 0: CF flag is not added. (LTC CF bit: 0)
ON 1: CF flag is added. (LTC CF bit: 1)
510 DF MODE
530 UB MODE
For setting the TCG drop frame mode.
DF 0: The unit is used in the drop frame mode.
NDF 1: The unit is used in the non-drop frame mode.
0000
0001
For setting the mode in which the user’s bit is used.
USER 0: The user’s bit is used for the user setting. (Fixed)
TIME 1: The user’s bit is used for displaying hours, minutes and seconds in real-
time operation.
0000
0001
0002
0003
DATE 2: The user’s bit is used for displaying the year, month, day, and time in
real-time operation.
EXT 3: The UBG value is slave-locked while the TC signal is input from an
external source.
(The user setting is used when no signal is input from an external
source.)
531 TCG SET HOLD
For setting whether to make the TCG setting operable when recording is to
be performed after the TCG is set, the power is turned off and back on
again.
0000
0001
OFF 0: Recording is performed according to the FIRST REC TC setting in No.
532.
ON 1: The TCG setting is made operable, and recording starts from the value of
the TCG displayed.
532 FIRST REC TC
For setting whether to record in the regeneration mode when recording for
the first time after the cassette was inserted or from the STOP mode or
power-on status.
0000
0001
REGEN 0: Recording is performed in regeneration mode.
PRESET 1: Recording is not performed in regeneration mode.
(Recording starts from the value of the TCG displayed.)
540
For setting the time and date.
TIME/DATE
00 YEAR
.
0000
00 For setting the year.
0099
0001
99
01 MONTH
02 DAY
01 For setting the month.
0012
0001
12
01 For setting the day.
0031
0000
31
03 HOUR
04 MINUTE
05 SET
00 For setting the hours.
0023
0000
23
00 For setting the minutes.
0059
–––
59
––– For setting the date and time.
The underlining indicates the factory setting.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
VIDEO menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
601 V-MUTE SEL
For setting whether to mute the video signals when LOW RF or NO RF has
occurred during playback.
0000
0001
N-MUTE 0: The video signals are not muted (the picture is frozen).
LOW RF 1: The video signal picture is muted (the screen turns gray).
608
For setting the setup processing for the composite IN/OUT and component
IN signals when the 25 Mbps mode is selected.
SET UP 25
.
00 CMPST IN
For setting the setup processing for the composite input signals.
THRU 0: The original signals are input as they stand.
CUT 1: The 7.5 % setup is eliminated from the input signals, which are then
input.
0000
0001
01 CMPST OUT
02 CMPNT IN
For setting the setup processing for the composite output signals.
THRU 0: The original signals are output as they stand.
ADD 1: The 7.5 % setup is added to the output signals, which are then output.
0000
0001
For setting the setup processing for the component input signals.
THRU 0: The original signals are input as they stand.
CUT 1: The 7.5 % setup is eliminated from the input signals, which are then
input.
0000
0001
609
For setting the setup processing for the composite IN/OUT and component
IN signals when the 50 Mbps mode is selected.
SET UP 50
.
00 CMPST IN
For setting the setup processing for the composite input signals.
THRU 0: The original signals are input as they stand.
CUT 1: The 7.5 % setup is eliminated from the input signals, which are then
input.
0000
0001
01 CMPST OUT
02 CMPNT IN
For setting the setup processing for the composite output signals.
THRU 0: The original signals are output as they stand.
ADD 1: The 7.5 % setup is added to the output signals, which are then output.
0000
0001
For setting the setup processing for the component input signals.
THRU 0: The original signals are input as they stand.
CUT 1: The 7.5 % setup is eliminated from the input signals, which are then
input.
0000
0001
The underlining indicates the factory setting.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
AUDIO menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
704 EMPHASIS
705 MONI SEL
0000
0001
OFF For setting the emphasis ON or OFF.
ON
For setting the audio signals which are to be output from the AUDIO OUT
connectors (PHONO), HEADPHONE jack and EARPHONE jack during
PLAY (FWD a1).
0000
0001
PLYPCM 0: PCM audio signals are output.
PLYCUE 1: Cue audio signals are output.
706 REC CUE
For setting the audio input signals which are to be recorded on the cue
track.
0000
0001
0002
CH1 0: CH1 input signals are recorded.
CH2 1: CH2 input signals are recorded.
CH1+2 2: CH1 and CH2 input signals are mixed and recorded.
730 DOUBLE REC
For setting whether the CH1 and CH2 input signals are to be recorded
simultaneously on CH3 and CH4.
(This item is valid only in the 50 Mbps mode.)
0000
0001
OFF 0: The signals are not recorded simultaneously.
(The CH3 and CH4 inputs signals are recorded on CH3 and CH4.)
ON 1: The signals are recorded simultaneously.
731 MONI OUT
For setting the audio signals to be monitored at the AUDIO OUT connectors
(PHONO) when PLYPCM has been selected as the No. 705 setting.
The cue audio signals are always output when PLYCUE has been selected
as the No. 705 setting.
0000
0001
0002
0003
0004
0005
CH1 0: The audio signals of CH1 are monitored.
CH2 1: The audio signals of CH2 are monitored.
CH3 2: The audio signals of CH3 are monitored.
CH4 3: The audio signals of CH4 are monitored.
CH1+2 4: The audio signals of CH1 and CH2 are mixed and monitored.
CH3+4 5: The audio signals of CH3 and CH4 are mixed and monitored.
732 LIMITER CH1
733 LIMITER CH2
734 LIMITER CH3
735 LIMITER CH4
For setting the CH1 audio limiter operation.
OFF 0: The limiter does not operate.
ON 1: The limiter operates.
0000
0001
For setting the CH2 audio limiter operation.
OFF 0: The limiter does not operate.
ON 1: The limiter operates.
0000
0001
For setting the CH3 audio limiter operation.
OFF 0: The limiter does not operate.
ON 1: The limiter operates.
0000
0001
For setting the CH4 audio limiter operation.
OFF 0: The limiter does not operate.
ON 1: The limiter operates.
0000
0001
736 MIC LOWCUT
CH1
0000
0001
OFF For setting the high-pass filter of the CH1 microphone ON or OFF.
ON
737 MIC LOWCUT
CH2
0000
0001
OFF For setting the high-pass filter of the CH2 microphone ON or OFF.
ON
738 MIC LOWCUT
CH3
0000
0001
OFF For setting the high-pass filter of the CH3 microphone ON or OFF.
ON
739 MIC LOWCUT
CH4
0000
0001
OFF For setting the high-pass filter of the CH4 microphone ON or OFF.
ON
The underlining indicates the factory setting.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
WARNING & ALARM menu
Item
Setting
Description of setting
Superimposed
display
Superimposed
display
No.
No.
900 BATT NEAR END
901 BATT END
For setting whether the warning alarm is to be sounded when the battery is
nearly totally discharged.
OFF 0: The warning alarm is not sounded.
ON 1: The warning alarm is sounded.
0000
0001
For setting whether the warning alarm is to be sounded when the battery is
totally discharged.
0000
0001
OFF 0: The warning alarm is not sounded.
ON 1: The warning alarm is sounded.
902 TAPE NEAR END
903 TAPE END
For setting whether the warning alarm is to be sounded when the tape is
approaching the end.
OFF 0: The warning alarm is not sounded.
ON 1: The warning alarm is sounded.
0000
0001
For setting whether the warning alarm is to be sounded when the tape has
reached the end.
0000
0001
OFF 0: The warning alarm is not sounded.
ON 1: The warning alarm is sounded.
904 TAPE WARNING
For setting the timing at which the warning alarm is to be sounded when the
tape is approaching the end.
0000
0001
2min 0: The warning alarm is sounded 2 minutes before the tape reaches the
end.
3min 1: The warning alarm is sounded 3 minutes before the tape reaches the
end.
905 TAPE REMAIN
906 ALARM SOUND
For setting the remaining tape time indicated by one segment on the
remaining tape display.
3min 0: Each segment is set to a remaining tape time of 3 minutes.
5min 1: Each segment is set to a remaining tape time of 5 minutes.
0000
0001
For setting the tone of the warning alarm.
NORMAL 0: The warning alarm tone is changed according to the nature of the
problem.
0000
0001
SIMPLE 1: The same warning alarm is sounded for all problems.
The underlining indicates the factory setting.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Backup Battery
The backup battery is installed before the unit is shipped from the manufacturing plant.
When the battery is totally discharged, the “E-90” error code appears for 3 seconds in the status
display window when the POWER switch is set to ON.
“00 : 00 : 00 : 00” is displayed as the TCG time code value, indicating that the time code can no
longer be backed up. In this situation, the backup battery must be replaced.
Consult your dealer, and replace with a new battery (CR2032 or BR2032).
VTR SYS
+
Panasonic
CR2032
No. 5 VTR SYS board
Backup battery
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
When a problem has occurred in the unit, one of the following error codes and warning displays will be displayed
on the status display window.
Error code
Warning display
Description
This appears when condensation (dew) has been detected.
Even after the cancellation of condensation detection, “HUMID” continues to flash for 20
minutes and the unit does not respond to the control key in order to ensure safety.
— d —
HUMID
This appears when the servo has failed to lock for more than 3 seconds.
If “T&S&R” has been selected as the setup menu item No. 003 setting, “SERVO NOT
LOCKED” is displayed on the third line (amount of remaining tape line) of the monitor
screen.
E — 00
SERVO
RF
This appears when there is no head output (due to clogging, etc.) for more than 3
seconds.
“L” is displayed on the first line (counter line) of the monitor screen.
If “T&S&R” has been selected as the setup menu item No. 003 setting, “LOW RF” is
displayed on the third line (amount of remaining tape line) of the monitor screen.
E — 01
This appears when the error rate has deteriorated (when the three channel condition
segments have lighted up).
If “T&S&R” has been selected as the setup menu item No. 003 setting, “HIGH ERROR
RATE” is displayed on the third line (amount of remaining tape line) of the monitor
screen.
E — 02
RF
RF
This appears when a blank portion on the tape has been detected.
“N” is displayed on the first line (counter line) of the monitor screen.
If “T&S&R” has been selected as the setup menu item No. 003 setting, “NO RF” is
displayed on the third line (amount of remaining tape line) of the monitor screen.
When all the following conditions are satisfied, the part of the tape concerned is
recognized as a blank part.
E — 09
When there is no output from any of the heads
When no playback data can be read
When there is no CTL signal
O
O
O
This appears when the reel base, which operates in accordance with the size of the
tape, has locked up for more than 2.5 seconds.
E — 11
SLACK
SLACK
This appears when the cassette down operation fails to take place even when 4
seconds have elapsed after the cassette was inserted.
Alternatively, it appears when the cassette fails to be ejected even when 4 seconds
have elapsed after its ejection operation was performed.
E — 21
E — 31
SLACK
SLACK
This appears when the loading operation fails to be completed within 4 seconds.
This appears when the unloading operation fails to be completed within 4 seconds.
E — 32
This appears when the FG signal (rotational speed signal) fails to be output from the
cylinder motor.
E — 41
SLACK
SLACK
This appears when the PG signal (phase signal) fails to be output from the cylinder
motor.
E — 42
E — 43
SLACK
SLACK
This appears when the cylinder motor’s speed is abnormally high.
E — 44
This appears when the cylinder motor’s speed is abnormally low.
This appears when the FG signal (rotational speed signal) fails to be output from the
capstan motor.
E — 51
SLACK
E — 52
E — 53
E — 61
E — 62
E — 63
E — 64
SLACK
SLACK
SLACK
SLACK
SLACK
SLACK
This appears when the capstan motor’s speed is abnormally high.
This appears when the capstan motor’s speed is abnormally low.
This appears when the supply reel motor has locked up.
This appears when the take-up reel motor has locked up.
This appears when the supply reel motor’s speed is abnormally high.
This appears when the take-up reel motor’s speed is abnormally high.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
Error code
Warning display
Description
E — 65
SLACK
SLACK
This appears when abnormal tension has been detected.
This appears when the start or end processing operation fails to be completed within 7
seconds.
E — 66
This appears when there is a communication error between SERVO and AVSYS.
There is a problem with the data.
E — 67
E — 68
E — 69
E — 6B
SLACK
SLACK
This appears when there is a communication error between SERVO and AVSYS.
The data is fixed to High or Low.
This appears when there is a problem in communication between SERVO and AVSYS
when the power is turned on.
SLACK
This appears when there is a communication error between IF and AVSYS.
There is a problem with the internal reference or external reference.
No display
E — 80
No display
No display
This appears when there is a problem with the supply voltage.
This appears when the backup battery has totally discharged.
E — 90
This appears when there is no input of video signals or when video signals are cut off
and the mismatching detector circuit has been activated.
E — A0
No display
(The [E-A0] and the time data will be displayed alternately in the REC PAUSE mode.)
This appears when the input DC voltage has dropped to near the undercut voltage level
(approx. 10.6 V).
E — bA
BATT flashes
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Emergency Eject
Procedure for manually ejecting the tape in an emergency
If the cassette tape cannot be removed even when the EJECT button is pressed, it can be ejected by following
the steps below.
Before proceeding, be absolutely sure to turn off the unit’s power.
O
1 Remove the top panel.
4 Once more use the Phillips head screwdriver to
push in and turn the red plastic screw part
counterclockwise. Again rotate the flange part of
the supply reel in the take-up direction to take up
the tape slack.
2 Use a Phillips head screwdriver to push in and turn
the red plastic screw part counterclockwise.
(This screw needs to be rotated about 30 turns
before unloading can be started.)
This two-step procedure needs to be repeated
until the tape is completely housed in the
cassette case (about 90 turns of the red plastic
screw part).
3 Insert the take-up jig (packed with the unit) into the
tape ejection slot (on the mechanism side of the
VTR), and rotate the flange part (white gear) of the
supply reel in the take-up direction to take up the
tape slack using the rubber part of the take-up jig.
5 Use the Phillips head screwdriver to turn the red
plastic screw part at the slot-in side clockwise to
eject the cassette tape.
<Note>
(This screw needs to be rotated through about
140 turns until the tape is ejected.)
Take care not to damage the tape in any way.
<Note>
Take care not to sandwich or catch the tape
when closing the cassette cover.
1
5
2
3
4
34
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning Systems
When trouble is detected immediately after the power has been switched on or while operation is underway, the
operator is alerted to its occurrence by the status display window (LCD), WARNING lamp and warning alarm
from the EARPHONE jack.
The warning alarm can be changed to the same for all errors (using setup menu item No. 906).
Status display window (LCD)
WARNING
lamp
Warning
alarm
Description of
warning
Warning Battery Remaining
Item
Operation of unit Remedial action
Warning
display
display charge
tape
status display display
NO RF
RF
Lights
Flashes 4
Sounds 4
Video heads
When head clogging Clean the heads. If
5)
°
times a second times a second clogged, problem in has been detected,
recording is still not
possible even after the
3)
°
LOW RF
recording system. the warning alarm is
sounded. It may not heads have been
be possible to record cleaned, turn off the
properly in this status. power and contact
your dealer.
HIGH
ERROR
RATE
SERVO SERVO Lights
Flashes 4
Sounds 4
Servo disturbances. Playback continues Turn off the power and
times a second times a second
but it may not be
possible to play
back the tape
properly in this
status.
contact your dealer.
(The lamp may flash
for a moment and then
go off when the tape
starts traveling: this is
normal and not
3)
°
indicative of
malfunctioning.)
HUMID
HUMID Lights or
flashes
Lights
Sounds 4
Condensation
times a second Warning alarm
The tape is
unloaded.
Stop the tape travel,
and turn off the
power. If the
“HUMID” display is
still not cleared
when the power is
turned back on, wait
until it is cleared.
1)
°
sounds when ON
was selected as
3)
°
setup menu item
Sounds
N.106 (HUMID
continuously
OPE).
2)
°
SLACK
SLACK Lights
Flashes 4
times a second continuously
Sounds
Tape take-up
problem.
An error code appears Check the error
where the time code is code (see pages 54
displayed on the
and 55) on the
status display window. status display
The unit stops
operating.
window, and
consult your dealer.
TAPE
END
E TAPE F Flashes
Flashes
1 of 7
segments
lights
Flashes once Sounds once a Tape is
Operation
continues.
Replace the tape
as necessary.
a second 1) second
1)
4)
°
°
approaching the
end.
°
7 of 7
segments
light
Lights
Sounds
continuously
Tape has reached Operation is
the end.
Replace or rewind
the tape.
stopped during
recording, playback
or fast forwarding.
4)
°
BATTERY E BATT F Flashes 1 of 7
END segments
Flashes once Sounds 4
The battery is
Operation
continues.
Replace the battery
as necessary.
a second
times a second nearly totally
3)
°
lights
discharged.
4)
°
Flashes 7 of 7
Lights
Sounds
continuously
The battery is
totally discharged. stopped.
Operation is
Replace the
battery.
segments
light
4)
°
1) During recording
2) At any time except during recording
3) Once a second when SIMPLE has been selected as the setup menu item No. 906 setting.
4) The alarm can be switched to ON or OFF using the alarm setup menu items No. 900 to No. 903.
°
°
°
°
°
5) RF warning display will flash during REC and REC PAUSE modes. When the unit changes from REC and REC PAUSE modes, the RF
warning display will turn off.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning Systems
Status display window (LCD)
WARNING
lamp
Warning
alarm
Description of
warning
Warning Battery Remaining
Item
Operation of unit Remedial action
Warning
display
display charge
tape
status display display
No
display
No
display
Flashes 4
Sounds 4
Memory status
Error code
[00:00:00:11] will
Switch the power
OFF and consult
times/second times a second error between
for 3 seconds
1)
°
SYSCON and DV. be displayed for 5 your local dealer.
seconds in the time
code display
position in the
status display
window.
However, the main
unit will be put into
Enforced Recording
mode and
recording will
continue.
1) During recording
2) At any time except during recording
3) Once a second when SIMPLE has been selected as the setup menu item No. 906 setting.
4) The alarm can be switched to ON or OFF using the alarm setup menu items No. 900 to No. 903.
°
°
°
°
°
5) RF warning display will flash during REC and REC PAUSE modes. When the unit changes from REC and REC PAUSE modes, the RF
warning display will turn off.
The warning system’s priority sequence is as
follows.
1 SLACK
6 SERVO
2 BATTERY END
3 TAPE END
4 HUMID
7 LOW RF
8 HIGH ERROR RATE
9 BATTERY NEAR END
10 TAPE NEAR END
5 NO RF
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Connector Signals
CAMERA connector (26-pin)
DC IN connector (XLR 4-pin)
Pin No.
Signal
Pin No.
Signal
1
2
COMPOSITE VIDEO
COMPOSITE VIDEO GND
Y GND
1
2
3
4
GND
3
4
Y
+12 V
5
PR/C
6
PR GND
7
PB
DC OUT connector (4-pin)
8
PB GND
9
CAMERA MIC (X)
CAMERA MIC (Y)
CAMERA MIC (G) GND
VTR START/STOP
BATTERY ALARM
TAPE REMAIN
REC/TALLY/WARNING
Pin No.
Signal
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
A
1
2
3
4
GND
+12 V
SHIELD
PLAYBACK VIDEO
PLAYBACK VIDEO GND
VTR SAVE/AUDIO MONITOR
COLOR FRAMING PULSE
POWER 12 V
POWER GND
B
REMOTE connector (9-pin)
Pin No.
Signal
1
2
3
4
5
6
7
8
9
GND
TRANSMIT A
RECEIVE B
RECEIVE COMMON
TRANSMIT COMMON
TRANSMIT B
RECEIVE A
GND
AUDIO IN/OUT connector (XLR 3-pin)
Pin No.
Signal
1
2
3
GND
HOT
COLD
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Head Cleaning
This unit is equipped with an auto head cleaning function which automatically reduces the
amount of dirt on the video heads. However, in order to maximize the unit’s reliability, it is
recommended that the video heads be cleaned as and when appropriate.
For further details on how to actually clean the heads, consult with one of our service
companies or with your dealer.
Condensation
The same principle by which droplets of water form on a window pane of a heated room is
responsible for the formation of condensation inside the unit. Condensation occurs in the unit or
on the tape when it is moved from one location to another where there is a significant difference
in temperature and humidity. More specifically, it forms:
When the unit (or tape) is moved to a very humid location where the air is full of steam or to a
O
room immediately after it has been heated
When the unit (or tape) is abruptly moved from an air-conditioned location to a very warm or
very humid location
O
When moving the unit to the kind of location described above, do not turn on its power
immediately but leave it standing for about 10 minutes. If condensation has formed inside the
unit, an error code (– d –) and warning display (HUMID) will light up on the status display
window, and the cassette tape will be automatically ejected.
Leave the power on, and wait until the error code (– d –) and warning display (HUMID) are
cleared.
Maintenance
Before proceeding with maintenance, be absolutely sure to set the power switch to OFF, and
disconnect the plug from the power outlet.
Use a soft cloth to clean the cabinet. To remove stubborn dirt, dilute some kitchen detergent,
soak a rag in the solution, wring it out well, and use it to wipe away the dirt. Wipe up any
remaining moisture using a dry cloth. Do not use paint thinners or benzine.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
[GENERAL]
[VIDEO]
Digital video
$
Supply voltage:
DC 12 V (DC 11 V – 17V)
Power consumption:
27 W (in power save mode) during recording
33 W during playback
Sampling frequency:
DVCPRO50
Y: 13.5 MHz, PB/PR: 6.75 MHz
DVCPRO
Y: 13.5 MHz, PB/PR: 3.375 MHz
Quantizing:
Ambient operating temperature:
32 °F to 104 °F (0 °C to 40 °C)
Storage temperature:
–4 °F to +140 °F (–20 °C to +60 °C)
Ambient operating humidity:
Less than 85 % (relative humidity)
Weight:
12.98 lb (5.9 kg)
Dimensions (WaHaD):
11 15/16˝a5 1/2˝a13 7/16˝ (303a139a341 mm)
Recording format:
8 bits
Video compression system:
DCT + variable length code
Compression rate:
3.3:1 (DVCPRO50)
5:1 (DVCPRO)
Error correction:
Reed-Solomon product code
Bit rate:
50 Mbps (DVCPRO50)
25 Mbps (DVCPRO)
DVCPRO50 format/DVCPRO format switchable
Recording tracks:
Camera component IN/composite OUT
Video band:
Y: 30 Hz to 5.75 MHz (+1.0 dB/–3.0 dB)
Signal-to-noise ratio:
$
$
Digital video: 525i
Digital audio
O
O
DVCPRO50: 48 kHz, 16 bits, 4 channels
DVCPRO: 48 kHz, 16 bits, 2 channels
Time code: sub-code area
Cue signal: 1 track
Better than 55 dB
Composite IN/composite OUT
Video band:
Y: 30 Hz to 4.5 MHz ( 1.0 dB)
Signal-to-noise ratio:
Better than 50 dB
Differential gain:
Less than 6 %
Differential phase:
Less than 4.5 degrees
Y/C delay:
O
O
O
Control (CTL) signal: 1 track
Tape speed:
DVCPRO50: 67.640 mm/s
DVCPRO: 33.820 mm/s
O
O
Recording time:
92 minutes (using AJ-5P92LP, DVCPRO50)
O
O
O
O
33 minutes (using AJ-P66MP, DVCPRO50)
184 minutes (using AJ-5P92LP, DVCPRO °)
66 minutes (using AJ-P66MP, DVCPRO)
Less than 20 ns
K factor (2T pulse):
Less than 2 %
° For AJ-5P92LP cassette tapes recorded using the DVCPRO
(25 Mbps) mode, use a VTR supporting DVCPRO (25 Mbps)
184 minute tapes.
Tape used:
[AUDIO]
1/4˝ thin magnetic layer metal tape
Sampling frequency:
48 kHz (synchronization with video signals)
Quantizing:
FF/REW time:
Approx. 5 minutes (using AJ-5P92LP)
Continuous recording operation time:
Approx. 110 minutes (using AU-BP402)
16 bits
Frequency response:
20 Hz to 20 kHz 1 dB (reference level)
Dynamic range:
More than 85 dB (1 kHz, emphasis OFF, “A”
weighted)
Distortion:
Less than 0.1 % (1 kHz, emphasis OFF, reference
level)
Wow & flutter:
Below measurable limits
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
[AUDIO]
[INPUT/OUTPUT CONNECTORS]
Headroom:
Other input/output connectors
DC IN:
$
20 dB
Emphasis:
XLR (4-pin) a1 (DC 11 V – 17 V)
T1 = 50 µs, T2 = 15 µs (ON/OFF switchable)
DC OUT:
4 pins a1 (DC 11 V – 17 V)
Maximum rated current: 200 mA
REMOTE:
[INPUT/OUTPUT CONNECTORS]
D-sub, 9 pins (female) a1 (for AJ-A95)
RS-422A interface standard complied with (no
editing functions)
Input connectors
VIDEO IN:
$
BNCa1, 1.0 V [p-p], 75 Ω
AUDIO IN:
LINE:
O
[LCD DISPLAY TUBE]
XLR (3-pin)a4 (CH1, CH2, CH3, CH4)
–60/+4 dBu switchable
Status display window
Counter:
$
–60 dBu, 3 kΩ/+4 dBu, high impedance
(Switchable to 600 Ω using internal switch)
Phantom mic power supply (+48 V) ON/OFF
selectable when –60 dBu is selected
(Switchable to +12 V using internal switch)
CAM:
8 digits (CTL/TC/UB switchable)
Warning displays:
RF, SERVO, HUMID, SLACK
Operating status:
DF, SLAVE, TCG, WIDE
Remaining tape, battery charge:
Segment display
O
Multi (26-pin), –60 dBu, 3 kΩ
CAMERA:
Multi (26-pin) a1
COMPOSITE IN: 1.0 V [p-p], 75 Ω
Y:
PB:
PR:
Signal level display window
Audio level display/input video signal level display
switchable
$
1.0 V [p-p], 75 Ω
0.7 V [p-p], 75 Ω
0.7 V [p-p], 75 Ω
16 steps + channel condition display
(75 % color bar, 7.5 % setup added)
TC IN:
BNC a1, 0.5 V to 8.0 V [p-p], 8 kΩ
Output connectors
[OPTIONAL EXTRAS]
$
Battery pack
O
O
O
O
VIDEO OUT 1/2:
AU-BP402
AC adapter
AJ-B75
9-pin remote controller
BNC a2, 1.0 V [p-p], 75 Ω
(Superimposed displays ON/OFF selectable for
VIDEO OUT 2)
Monitor VIDEO:
PHONO a1, 1.0 V [p-p], 75 Ω
AUDIO OUT:
AJ-A95
9-pin remote cables
AU-C5 (5 meters), AU-C10 (10 meters)
XLR (3-pin) a4 (CH1, CH2, CH3, CH4)
+4 dBu low impedance
PHONO a1, –20 dBu, low impedance
TC OUT:
Weight and dimensions shown are approximate.
Specifications are subject to change without notice.
BNC a1, 2.0 V [p-p], low impedance
PHONES:
M6 a1, M3 a1
Stereo, 8 Ω, CH1/CH2 and CH3/CH4
switchable, playback control supported
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
PANASONIC BROADCAST & DIGITAL SYSTEMS COMPANY
DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
Executive Office:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621
Mid-Atlantic/New England:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621
Southeast Region:
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835
Central Region:
1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
Dallas Region:
6226 Abington Way, Houston, TX 77008 (713) 802-2726
No. CA/Northwest Region:
5870 Stoneridge, #3, Pleasanton, CA 94588 (925) 416-5108
Government Marketing Department:
52 West Gude Drive, Rockville, MD 20850 (301) 738-3840
PARTS INFORMATION & ORDERING:
9:00 a.m. – 5:00 p.m. (EST) (800) 334-4881/24 Hr. Fax (800) 334-4880
TECHNICAL SUPPORT:
Emergency 24 Hour Parts & Service (800) 222-0741
TRAINING INFORMATION:
Digital System Products - (201) 392-6852
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010
Panasonic de Mexico S.A. de C.V.
Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127
Download from Www.Somanuals.com. All Manuals Search And Download.
|