High Power Receiver
CR-W400U
Operating Instructions
Please read these instructions carefully before using this product and save this manual for future use.
Download from Www.Somanuals.com. All Manuals Search And Download.
Panasonic welcomes you to our ever growing family of electronic product owners. We know that this
product will bring you many hours of enjoyment. Our reputation is built on precise electronic and
mechanical engineering, manufactured with carefully selected components and assembled by people
who take pride in their work. Once you discover the quality, reliability, and value we have built into this
product, you too will be proud to be a member of our family.
Use This Equipment Safely
❏
When Driving
Keep the volume level low enough to be aware of road and traffic conditions.
When Washing Vehicle
Do not expose the equipment, including the speakers to water or excessive moisture. This could cause
electrical shorts, fire or other damage.
When Parked
Parking in direct sunlight can produce very high temperatures inside your vehicle. Give the interior a
chance to cool down before switching the unit on.
Use the Proper Power Supply
This equipment is designed to operate off a 12 volt, negative ground battery system (the normal system
in a North American vehicle.)
Use Authorized Service centers
Do not attempt to disassemble or adjust this precision equipment. Please refer to the Service center list
included with this product for service assistance.
For Installation
The product should be installed in a horizontal position with the front end up at a convenient angle, but
not more than 30˚.
Find the model number and serial number on either the back or bottom of the unit. Please record them
in the space below and retain this booklet as a permanent record of your purchase to aid in
identification in case of theft.
MODEL NUMBER
CR-W400U
SERIAL NUMBER
FROM
DATE PURCHASED
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Use This Equipment Safely ...................................................................Page 2
Power and Sound Controls ......................................................................4
How to adjust the volume, mute, balance, and tone for best listening
❏
❏
Radio Basics..............................................................................................6
Mode selection, manual and automatic tuning, band selection,
preset stations
Clock Basics..............................................................................................9
❏
Setting the time, selecting the clock display
In case of Malfunction ............................................................................10
❏
❏
Installation Guide....................................................................................11
Step-by-step procedures, electrical connections
Troubleshooting ......................................................................................15
❏
Troubleshooting tips, where to get service help
Specifications .............................................................................................17
Part 15 of the FCC Rules............................................................................17
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Power and Sound Controls
CRW400U
Power
If the vehicle is not running yet, turn the key in the ignition until the
accessory indicator lights.
Press [PWR] to switch on the power.
Volume
●
Press the knob to select the volume mode and then turn it
clockwise or counterclockwise to adjust the volume level.
Volume Level
0 to 40
d
Anti-Volume-Blast Circuit
At power on, the volume returns to the previous level slowly if
the level was at 20 or higher.
Changing Audio Modes
Press this knob [SEL] to change the audio mode as follows.
VOL
(Volume)
c
BASS
TRE
(Treble)
d
a
a
FADE
BAL
b
(Fader)
(Balance)
d
Bass and Treble
Press the knob to select the BASS or TREBLE mode and then turn
it clockwise or counterclockwise to increase or decrease the
bass/treble level.
-12 to 12
-12 to 12
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Power and Sound Controls (continued)
Balance
Press the knob to select the BALANCE mode and then turn it
clockwise or counterclockwise to shift the sound volume to the right
or left speakers.
or L 1 to 15
(R: Right, L: Left)
Balance Center
Fader
Press the knob to select the FADER mode and then turn it
clockwise or counterclockwise to shift the sound volume to the front
or rear speakers.
or R 1 to 15
(F: Front, R: Rear)
Fader Center
Note: In the audio mode (BASS/TRE/BAL/FADE), the display
will return to regular operation mode when there is no input for
more than 5 seconds (2 seconds in the VOL mode).
Press and hold
Tone Enhancement (Loudness)
●
Press and hold [BAND] (LOUD) for more than 2 seconds to
enhance bass and treble tones when listening at low or medium
volume.
CRW400U
●
Press and hold [BAND] (LOUD) for more than 2 seconds again to
deactivate when listening at higher volumes.
Mute
●
Press [MUTE] to mute the sound completely.
●
Press [MUTE] again to cancel.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio Basics
CRW400U
Selecting a Band
Press [BAND] to change the band setting as follows.
FM1
FM2
W/B
AM
a
a
a
(Weather Band)
c
d
CRW400U
"ST" indicator lights when FM stereo breadcast is available.
Manual Tuning
Press [TUNE
] or [TUNE
] to tune in a higher or lower
i
j
frequency.
Hold and release
Seek Tuning
Press and hold [SEEK
seconds, then release it.
] or [SEEK
] for more than 0.5
j
i
Seek tuning will automatically stop when a signal of the next
broadcast station is received.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio Basics (continued)
Station Preset
FM1, FM2 and AM can save maximum 6 stations each in their preset station memories.
Caution: To ensure safety, never attempt to preset stations while you are driving.
Manual Station Preset
ቢ
ባ
Press [BAND] to select a desired band.
Use manual or seek tuning to find a station to be stored in the
preset memory.
ቤ
Press and hold one of the preset buttons [1] to [6] until the
display blinks once.
CRW400U
ቢ
d
Preset Number
Note: You can change the memory setting by repeating the above
procedure.
ባ
d
ቤ
Auto Station Preset
Select a band and press and hold [SCAN] (AUTO PRESETS) for
more than 2 seconds.
●
The 6 strongest available stations will be automatically saved in
the memory on preset buttons [1] to [6].
CRW400U
●
Once set, the preset stations are sequentially scanned for 5
seconds each.
Notes:
d
Press and hold
●
In Auto Station Preset mode, only FM2 is available for FM
stations. (FM1 is not available.)
●
Auto Station Preset is not activated in Weather Band.
●
Any stations preset previously on the selected band will be
erased.
Tuning in a Preset Station
Press the corresponding preset buttons [1] to [6] to tune in a preset
station.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuning in a Weather Band
Station
Press any of the buttons [1] to [6] to monitor the preset station.
The frequency (162) remains unchanged.
WB
Weather Band Frequency Channel Number
Note: The weather band (CH1-6) has been preset. CH7 is
selected by pressing [ ] or [ ].
j
i
Weather Band Stations
National Weather Radio Broadcasts from over 380 locations
throughout the U.S. on seven VHF/FM frequencies.
Tune to weather band to receive continuous weather information 24
hours a day on one of the following frequencies.
1. 162.550 MHz
2. 162.400 MHz
3. 162.475 MHz
4. 162.425 MHz
5. 162.450 MHz
6. 162.500 MHz
7. 162.525 MHz
Occasionally the frequency of an existing or planned station must
be changed because of unexpected radio frequency interference
with adjacent NOAA Weather Radio Stations and/or with other
Government or Commercial Operations within the area. If you have
a question concerning NOAA Weather Radio, please contact your
nearest National Weather Service Office.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock Basics (The clock system is 12-hours.)
CRW400U
Initial Time
ቢ
Press and hold [CLK] to set time. Display blinks, and the time
setting mode is activated.
Press [ ] to set the hour.
i
Press [ ] to set the minute.
j
CRW400U
ቢ
(Hold [ ] or [ ] to change numbers rapidly.)
i
j
d
ባ
Once the time has been set, release [CLK].
Note: When the clock is not set yet, "SET" is displayed.
ቢ
or
Time Reset
ቢ
ባ
When you want to reset the time, repeat steps
and
above.
ቢ
ባ
CRW400U
Clock Display
Press [CLK] to display the current time.
Press [CLK] again to return to previous display.
Note: The current time will be displayed at all the time even the
CRW400U
power of the radio is turned off.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
In Case of Malfunction
Reset Switch
If the unit does not respond when the function buttons are
pressed, press the reset switch with a small pointed object,
such as a pencil point. This will restore the unit to its default
settings. All previously stored memory settings will be
erased. Repeat the necessary steps in the previous pages to
reprogram the clock and memory settings. If pressing the
reset switch does not restore normal operation, please
return the radio to the nearest authorized service center for
service.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
WARNING
This installation information is designed for experienced installers
and is not intended for non-technical individuals. It does not
contain warnings or cautions of potential dangers in attempting to
install this product.
Any attempt to install this product in a motor vehicle by anyone
other than qualified installer could cause damage to the electrical
system and could result in serious personal injury or death.
Overview
Installation Hardware
❏
❏
This equipment should be installed by a
professional. However, if you plan to install this
unit yourself, your first step is to decide where to
install it. The instructions in these pages will
guide you through the remaining steps: (Please
refer to "WARNING" statement above).
No.
Item
Diagram Qty
ቢ
Mounting Collar
1
●
Identify and label the vehicle wires.
●
Connect the vehicle wires to the wires of the
power connector.
●
Install the unit in the dash.
●
Check the operation of the unit.
If you do encounter problems, please consult
your nearest authorized dealer.
Caution: This unit will operate with a 12 volt DC
negative ground auto battery system only. Do
not attempt to use it in any other system. Doing
so could cause serious damage.
Before you begin installation, look for the following
items included in the packing with your unit.
●
Installation Hardware ...... Needed for in-dash
installation
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Procedures
❏
●
When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure
your hands and fingers.
●
We strongly recommend you to wear gloves for installation work to protect yourself from injuries.
Note: Disconnect the cable from the negative (–) battery terminal.
ቢ
1. Secure the Mounting Collar
.
ቢ
Insert Mounting Collar
screwdriver.
into the vehicle's dashboard, and bend mounting tabs out with a
Mounting Tab
Dashboard
1
Mounting Collar
Screwdriver
2. Secure the rear of the unit.
a) Insert Power Connector to the unit.
b) Check the electrical connection by referring to this operating instructions.
ቢ
c) Insert the unit into Mounting Collar
and push it in until "click" is heard.
Power Connector
Unit
12
Download from Www.Somanuals.com. All Manuals Search And Download.
To remove the unit from the vehicle's dashboard
Insert each removal tool and pull.
Removal tool
(U-shaped)
Note: Do not lose removal tools. They will be needed to remove the unit from the vehicle's
dashboard.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
Cautions:
●
This product is designed to operate with a 12-volt negative ground battery system.
●
To prevent damage to the unit, be sure to follow the connection diagram below.
●
Do not insert the power connector into the unit until the wiring is completed.
●
Be sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis. Bundle
all cables and keep cable terminals free from touching any metal parts.
Receiver
CR-W400U
Antenna
(Rear Side)
Power Connector
(Red)
ACC
Power Lead (ACC or IGN)
To ACC power, +12V DC
(Black)
Ground Lead
To a clean, bare metallic part of
the vehicle chassis
Ground
Battery
Battery Lead
To the vehicle battery, continuous
+12V DC
(Yellow)
(Orange w/White stripe)
(Violet w/black stripe)
Dimmer
Dimmer Control Lead
Connect to vehicle dimmer control lead
(Gray w/black stripe)
(white) (Gray)
(White
w/black
stripe)
(Green
w/black
stripe)
(Green)
(Violet)
Left Speaker
(Front)
Right Speaker
(Front)
Left Speaker
(Rear)
Right Speaker
(Rear)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Maintenance
When Something Doesn't Work
❏
❏
Your product is designed and manufactured to
ensure a minimum of maintenance. Use a soft
cloth for routine exterior cleaning. Never use
benzine, thinner, or other solvent.
Check the charts on page 16 for possible causes
and solutions to any problem you might be
experiencing. Some simple checks or minor
adjustments may eliminate the problem.
Product Servicing
❏
If the suggestions in the charts do not solve the
problem, we recommend that you take it to your
nearest authorized PASC service center. The
unit should be serviced only by a qualified
technician.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (continued)
Troubleshooting Tips
❏
PROBLEM
POSSIBLE CAUSE
PROBABLE SOLUTION
Unit does not turn on.
Dead vehicle battery
Ignition or Acc is not on.
Bad power line connection
Charge vehicle battery.
Turn ignition to On or Acc.
Check connections.
Radio has static.
Antenna not hooked up
Close to high power lines
Hook up antenna.
Move away from high power lines.
Radio memory buttons do not Not holding buttons down long Press and hold buttons for more
work. enough than 2 seconds.
Inverted sound (Left/Right conn- The speaker cords are inverted. Check the speaker cords.
ections.)
No sound from front or rear The fader control is set on the Adjust the fader control of the
speakers
wrong position.
unit correctly.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General
Power Supply
Maximum Power Output
: 12 V DC (11V-16V) Test Voltage 14.4V, Negative ground
×
: 37W 4 channels at 400 Hz, Volume Control maximum
Power Output
: 18W per channel into 4 ohms, 40 to 30,000Hz at 3% THD.
Tone Action
: Bass; ± 12 dB at 100 Hz
Treble; ± 12 dB at 10 kHz
Current Consumption
Speaker Impedance
: Less than 2.5 A (0.5W 4-speaker)
: 4 Ω (4-8 Ω acceptable)
×
×
×
×
×
×
Dimensions (W
Weight
H
D)
: 7" 1-15/16" 5-7/8" (178 50 150 mm)
: 1 lbs. 14 oz. (0.85 k )
g
AM Radio
Frequency Range
: 530-1,710 kHz
Useable Sensitivity
: 28 dB/µV (25 µV/ S/N 20 dB)
FM Stereo Radio
Frequency Range
Useable Sensitivity
50 dB Quienting Sensitivity
Frequency Response
Alternate Channel Selectivity
Stereo Separation
: 87.9-107.9 MHz
: 12 dBf. (1.1 µV / 75Ω, S/N 30 dB)
: 17 dBf. (1.8 µV / 75Ω)
: 30-15,000 Hz ± 3 dB
: 75 dB
: 35 dB at 1,000 Hz
: 70 dB (Mono)
Signal/Noise Ratio
Weather Band Radio
Frequency Range
Useable Sensitivity
Signal/Noise Ratio (40 dB/µV)
: 162.40-162.55 MHz
: 3 dB/µV (S/N 20 dB)
: 50 dB
*Above specifications comply with EIA standards.
Note: Specifications and design are subject to modification without notice due to improvements in
technology.
Part 15 of the FCC Rules
This unit has been manufactured under the Part 15 of the FCC Rules.
Do not attempt to make any changes or modifications to this unit.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Panasonic Consumer Electronics
Company, Division of Matsushita
Electric Corporation of America
One Panasonic Way, Secaucus,
New Jersey 07094
YFM284C337ZA TAMACO0900-0 Printed in Taiwan
Download from Www.Somanuals.com. All Manuals Search And Download.
|