Packard Bell Laptop H5 User Manual

Versa M440  
Disassembly Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Overview  
This document contains step-by-steps disassembly instructions for the Versa M440/EasyNote H5 chassis. The  
instructions are illustrated where necessary with images of the part that is being removed or disassembled.  
Furthermore, the screws that are removed are shown next to the image of the parts themselves.  
NEC reserves the right to make changes to the Versa M440/EasyNote H5 chassis without notice.  
Technician Notes  
Only technicians authorized by NEC Computers International BV should attempt to repair this equipment. All  
troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the  
complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component  
level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. Any  
indication of component replacement or printed wiring board modifications may void any warranty or exchange  
allowances.  
Disassembly Instructions  
When disassembling the system unit, follow these general rules:  
Do not disassemble the system into parts that are smaller than those specified in the instructions.  
Label all removed connectors. Note where the connector goes and in what position it was installed.  
Turn off the power and disconnect all power and all options.  
Reassembly Instructions  
Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and screws are returned  
to their proper positions. Check that no tools or any loose parts have been left inside the chassis. Check that  
everything are properly installed and tightened.  
Required Tools  
All disassembly procedures can be perform using the following tools:  
PH 0x60 Philips screwdriver  
PH 0x40 Philips screwdriver  
4.0 x 60 Flat screwdriver  
2.0 x 30 Flat screwdriver  
SW5.0 Spacer screwdriver  
Small tweezers  
Pin  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Ensure that the computer is disconnected from  
its power source and from all  
telecommunications links, networks, or modem  
lines whenever the chassis cover is removed.  
Do not operate the computer with the cover  
removed.  
Hazardous Voltage  
There is hazardous voltage present inside the computer  
when it is connect to an AC supply, even when the  
computer’s power switch is off. Exposure to hazardous  
voltage could cause personal injury. To avoid risk of injury,  
contact an Authorized Service Provider for proper  
(UN)installation of optional hardware devices.  
AVERTISSEMENT  
Assurez-vous que le système est débranché de  
son alimentation ainsi que de toutes les  
liaisons de télécommunication, des réseaux, et  
des lignes de modem avant d’enlever le capot.  
Ne pas utiliser le système quand le capot est  
enlevé.  
Avoid Electrostatic Discharge  
Electrostatic electricity can easily damage circuit cards and  
integrated circuits (ICs). To reduce risk of damage, store  
them in protective packaging whenever they are not  
installed in your system.  
WARNUNG  
Das System darf weder an eine Stromquelle  
angeschlossen sein noch eine Verbindung mit  
einer Telekommunikationseinrichtung, einem  
Netzwerk oder einer Modem-Leitung haben,  
wenn die Gehäuseabdeckung entfernt wird.  
Nehmen Sie das System nicht ohne die  
Abdeckung in Betrieb.  
Add-in cards can be extremely sensitive to ESD and always  
require careful handling. After removing the card from the  
computer, place the card flat on a grounded, static-free  
surface, component-side up. Use a conductive foam pad if  
available, but not the card wrapper. Do not slide the card  
over any surface.  
Before you install or remove memory modules, video  
memory, disk drives, circuit cards or other devices, protect  
them from static electricity. To do so, make sure your  
computer’s power switch is OFF. Then, unplug the  
computer’s AC power cord. Before picking up the device you  
(un)install, you should wear an anti-static wrist wrap  
(available at electronic supply stores). Be sure to connect  
the wrist wrap to an unpainted metal portion of the computer  
chassis. As an alternative, you can dissipate electrostatic  
build-up by touching an unpainted metal portion of the  
computer chassis with one hand. Then touch the device you  
are (un)installing with the other hand, and maintain  
continuous contact with it until it is (un)installed in the  
computer.  
ADVERTENCIA  
Asegúrese de que cada vez que se quite la  
cubierta del chasis, el sistema haya sido  
desconectado de la red de alimentación y de  
todos lo enlaces de telecomunicaciones, de red  
y de líneas de módem. No ponga en  
funcionamiento el sistema mientras la cubierta  
esté quitada.  
WAARSCHUWING  
Zorg er voor dat alle verbindingen van en naar  
de computer (stroom, modem netwerk, etc)  
verbroken worden voordat de behuizing  
geopend wordt. Zet de computer nooit aan als  
de behuizing geopend is.  
AVVERTENZA  
Prima di rimuovere il coperchio del telaio,  
assicurarsi che il sistema sia scollegato  
dall’alimentazione, da tutti i collegamenti di  
comunicazione, reti o linee di modem. Non  
avviare il sistema senza aver prima messo a  
posto il coperchio  
Power Supply Unit  
Under no circumstances should you attempt to disassemble  
the power supply. The power supply contains no user-  
serviceable parts. Inside the power supply are hazardous  
voltages that can cause serious personal injury. Always  
return a defective power supply to your dealer.  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the Battery  
Perform the following steps to remove the battery:  
1. Make sure to power off the Versa M440/EasyNote H5.  
2. Turn the unit upside down.  
3. Unscrews the bottom cover door and slide it out of its place as the arrow shows in Fig. 1  
M2.5x7 Black  
Fig. 1 Removing Bottom cover door  
4. Pull up the battery as shows in Fig. 2  
Fig. 2 Pull up battery  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the Memory Module  
To remove the Memory Module, first remove the battery (see Removing the Battery), then  
perform the following steps:  
1. Unclip the memory module as shown in Fig. 3  
Fig. 3 Removing the memory module  
2. Remove the memory module from its slot and put it aside.  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the Hard Disk Drive  
To remove the hard disk drive, first remove the battery (see Removing the Battery), then  
perform the following steps:  
1. Remove the screws as shown in Fig. 4  
M2.5x5 Silver  
Fig. 4 Screw retaining the HDD module  
2. Carefully pull the HDD module out from the base unit as shown in Fig. 5 .  
1
2
Fig. 5 Removing HDD module  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the CPU  
To remove the CPU first remove the battery (see Removing the Battery) then perform the  
following steps:  
1. Unscrew screws on CPU Heat Sink in descending order (5Æ4Æ3Æ2Æ1) as shown in Fig.  
6
M2.5x5 Silver  
Fig. 6 CPU Heat Sink  
Note: Beware of screws use on the CPU heat sink! Ensure to use the screw size M2.5x5, otherwise it  
might cause damage to CPU die or Main Board. When install heat sink, screws must be secured in  
ascending order (1Æ2Æ3Æ4Æ5).  
2. Unlock the CPU from the CPU socket and lift up the CPU carefully.  
Fig. 7 Unlocking the CPU  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the Keyboard  
To remove the Keyboard, first remove the battery (see Removing the Battery), then perform  
the following steps:  
1. Release the keyboard from the base unit by push KB lock with flat screws driver as shown  
in Fig. 8  
Fig. 8 Releasing the keyboard cover  
2. Lift up the keyboard and disconnect it from the system as shown in Fig. 9  
Fig. 9 Disconnecting the keyboard flat cable  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the Optical Disk Drive  
To remove the ODD, first remove the battery (see Removing the Battery) then perform the  
following steps:  
1. Flip over the unit, unscrew and pull the ODD module out from the base unit as shown in  
Fig. 10  
M2.5x7 Black  
Fig. 10 Pushing the optical drive out from the base unit  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the LCD Module  
To remove the LCD Module first remove the battery (see Removing the Battery) and remove  
the Keyboard (see Removing the Keyboard) then perform the following steps:  
1. Remove the hinge cover as shown in Fig. 11  
M2x3 Black  
Fig. 11 Removing the hinge cover  
2. Disconnect LCD cable as shown in Fig. 12  
Fig. 12 Disconnecting LCD Cable  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Release two screws at both side of LCD hinge, remain two outer screws attached.  
M2.5 x 7 Silver  
Fig. 13 Removing screws at LCD hinge  
4. Open up the LCD panel at 45o then remove two outer screws on LCD hinge.  
M2.5 x 7 Silver  
Fig. 14 Removing outer screw at LCD hinge  
5. Carefully separate the LCD Module from the base unit.  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the LCD Panel  
To remove the LCD panel, first remove the LCD module (see Removing the LCD Module),  
then perform the following steps:  
1. Use a pin to remove the rubber cover on the LCD module as shown in Fig. 15  
2. Remove all screws as shown in Fig. 15  
A = M2.5x5 Silver  
B = M2x6 Silver  
Fig. 15 Removing the rubber covers & screws on the LCD Module  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Carefully release LCD Bezel form LCD module as shown in Fig. 16  
1
2
2
Fig. 16 Removing the LCD Bezel  
4. Release the inverter board by remove the screw and disconnect all connectors as shown  
in Fig. 17  
M2x5 Silver  
Fig. 17 Removing the Inverter Board  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Release six screws at the side of the LCD Penal and two screws on LCD Hinge.  
A = M2x5 Silver  
B = M2.5 x 5  
Silver  
Fig. 18 Removing the LCD Panel hinges  
6. Carefully lift up the LCD panel.  
7. Remove the screws at both sides of the LCD panel in order to release the LCD hinges as  
shown in Fig. 19  
M2x3.5 Silver  
Fig. 19 Removing the LCD Panel hinges  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the Bottom Cover  
To remove the Top Cover , first remove the battery (see Removing the Battery), remove the  
Optical Disk Drive (see Removing the Optical Disk Drive) then perform the following steps:  
1. Remove all screws on the bottom of the base unit as shown in Fig. 20  
A = M2.5x7 Black  
B = M2.5 x 5  
Silver  
Fig. 20 Bottom Cover  
2. Locate and release two screws at the rear of Bottom cover as shown in Fig. 21 .  
M2x3 Black  
Fig. 21 Bottom cover  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Carefully lift up bottom cover from base unit as shown in Fig. 22 and place it aside.  
Fig. 22 Lifting up the Bottom cover  
Removing the MDC Modem  
To remove the MDC Modem, first remove the Bottom Cover (see Removing the Bottom Cover)  
then perform the following steps:  
1. Release screws and disconnect cable on MCD Modem as shown in Fig. 23  
M2x4 Silver  
Fig. 23 MDC Modem  
2. Lift up the MDC modem and put it aside.  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the Chipset Heat Sink  
To remove the Chipset heat sink, first remove the Bottom cover (see Removing the Bottom  
Cover) then perform the following steps:  
1. Unscrew the screws on the Chipset Heat sink in descending order (4Æ3Æ2Æ1)  
disconnect the fan connector as shown in Fig. 24  
M2.5 x 5 Silver  
Fig. 24 Chipset Heat sink  
2. Carefully lift up heat sink from Main Board.  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the Multi card reader  
To remove the Multi card reader, first remove the Hard Disk Drive (see Removing the Hard  
Disk Driver ) then perform the following steps:  
1. Unscrew the screws on the Multi Card Reader and disconnect it as shown in Fig. 25  
M2x4 Silver  
Fig. 25 Multi card Reader  
2. Carefully separate the Multi card Reader from Top cover.  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the Main Board  
To remove the Main Board, first remove the Bottom cover (see Removing the Bottom Cover)  
then perform the following steps:  
1. Remove the right hinge cover as shown in Fig. 26  
M2x3 Black  
Fig. 26 Removing the right hinge cover  
2. Disconnect LCD cable as shown in Fig. 27  
Fig. 27 Disconnecting LCD Cable  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Remove the Hex screws from the VGA Port as shown in Fig. 28  
A = M2.5x6 Silver  
B = M2.5x9 Silver  
C = M2.5x19.5  
Silver  
Fig. 28 Main Board  
4. Release Hex screws from VGA and Parallel Port  
M2.5x10 Silver  
Fig. 29 VGA & Parallel Port  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Pull the plastics part near to audio port outward to release Main Board and carefully lift up  
the Main Board as shown in Fig. 30  
Fig. 30 Lifting up Main Board  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the Top Shield  
To remove the Top Shield, first remove the Main Board (see Removing the Main Board), then  
perform the following steps:  
1. Remove screws on top cover as shown in Fig. 31  
Fig. 31 Top Cover  
2. Unscrew all screws and disconnect all cable on the Top Shield as shown in Fig. 32  
A = M2.5 x 5  
Silver  
B = M2.5x7 Black  
Fig. 32 Top Shield  
3. Carefully separate the Top shield from Top cover.  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Release the Switch Board and LED Board on Top Shield by remove four screws encircle in  
Fig. 33  
M2x3.5 Silver  
Fig. 33 Switch Board and LED Board  
Removing the Touch Pad  
To remove the touch pad, first remove the top shield (see Removing the Top Shield ) then  
perform the following steps:  
1. Unscrew the screws on the Touch Pad Holder as shown in Fig. 34  
M2x3 Silver  
Fig. 34 Touch Pad  
2. Press on Touch Pad Button hock to release Touch Pad Holder as shown in Fig. 35  
Fig. 35 Touch Pad Holder  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing the Speaker Assembly  
To remove the Speaker Assembly, first remove the Main Board (see Removing the Main  
Board) then perform the following steps:  
1. Remove the screws holding Speaker Assembly as shown in Fig. 36  
M2x3 Black  
Fig. 36 Speaker Assembly  
2. Carefully remove the Speaker assembly from Top Cover and place it aside.  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Screws  
M2.5x7 Black  
M2.5x5 Silver  
M2x5 Silver  
M2x3 Black  
M2.5x7 Silver  
M2x4 Silver  
M2x6 Silver  
M2x3 Silver  
M2x3.5 Silver  
M2.5x10 Silver  
M2.5x19.5 Silver  
M2.5x9 Silver  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notice  
The information in this guide is subject to change without notice.  
This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in  
any form or by any means without prior written consent from NEC Computers International BV.  
NEC COMPUTERS INTERNATIONAL BV SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS  
OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING  
FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.  
Copyright © 2004 NEC Computers International BV. All rights reserved.  
NEC is a trademark of NEC Computers International BV.  
The names of actual companies and products mentioned herein may be trademarks and/or registered trademarks  
of their respective owners.  
Versa M440/EasyNote H5 Disassembly Manual  
Author: Allen Koay  
First Edition: April 2004  
Document Part Number:  
Version: 1.0  
NECCM  
A division of NEC Computers International BV  
NEC Versa M440/PB Easy Note H5 Disassembly Manual  
Page 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Dishwasher M NR 09 116 600 00 User Manual
National Instruments Network Card NI 9481E User Manual
NordicTrack Home Gym 831237651 User Manual
Omega Vehicle Security Heat Pump PPA100 User Manual
Optimus Cassette Player SCP 90 User Manual
Panasonic All in One Printer KXF120 User Manual
Panasonic All in One Printer KX MB1500 User Manual
Panasonic Cell Phone F77G User Manual
Panasonic Credit Card Machine GN SERIES User Manual
Panasonic Telephone KX TC1005ALB User Manual