Cordless Drill & Driver/Cordless Hammer Drill & Driver
Perceuse-visseuse sans fil/Perceuse à percussion-visseuse sans fil
Destornillador y taladro sin cables/Destornillador y taladro percutor sin cables
Operating Instructions
Instructions d'utilisation
Manual de instrucciones
Model No: EY7450/EY7950
IMPORTANT
This manual contains safety information. Read manual completely before first using this product and save this manual for
future use.
IMPORTANT
Ce mode d’emploi contient des informations sur la sécurité. Lisez-le en entier avant d’utiliser le produit et conservez-le pour
référence.
IMPORTANTE
Este manual contiene información de seguridad. Lea completamente este manual antes de utilizar por primera vez este
producto, y guárdelo para poder consultarlo en el futuro.
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
1
2011-2-17
11:48:01
This tool, as a complete unit with a battery
pack, satisfies appropriate IP Degrees of
Protection based on the IEC regulations.
SAVE THESE INSTRUCTIONS
Work Area Safety
1) Keep work area clean and well lit.
Cluttered or dark areas invite acci-
dents.
2) Do not operate power tools in ex-
plosive atmospheres, such as in
the presence of flammable liq-
uids, gases or dust.
Power tools create sparks which
may ignite the dust or fumes.
3) Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose
control.
Definition of IP code
IP5X: Ingress of dust is not total-
ly prevented, but dust shall not pen-
etrate in a quantity to interfere with
satisfactory operation of the tool or to
impair safety (In case that the talcum
powder under 75 μm intrudes inside
the tool).
IPX6: Water projected in powerful jets
against the tool from any direction
shall have no harmful effects (In case
that, with a nozzle of 12.5 mm inner
diameter, approximately 100 L/min of
normal temperature water is injected
to the tool for 3 minutes from 3 meter
distance).
Electrical Safety
1) Power tool plugs must match
the outlet. Never modify the
plug in any way. Do not use
any adapter plugs with earthed
(grounded) power tools.
LIMITED WARRANTY
The rating of IP56 qualifies this tool
for the minimum impact of water or
dust, but not for the assurance of per-
formance in such conditions. See
Safety and Operating Instructions for
further details for proper operation.
Unmodified plugs and matching out-
lets will reduce risk of electric shock.
2) Avoid body contact with earthed
or grounded surfaces such as
pipes, radiators, ranges and refrig-
erators.
There is an increased risk of elec-
tric shock if your body is earthed or
grounded.
I. INTRODUCTION
These tools can be used to tight-
en screws in clutch mode and to
drill holes in wood and metal in drill
mode. Additionally, model EY7950
can be used to drill holes in soft con-
crete and similar materials in ham-
mer mode.
3) Do not expose power tools to
rain or wet conditions.
Water entering a power tool will in-
crease the risk of electric shock.
4) Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep
cord away from heat, oil, sharp
edges or moving parts.
Damaged or entangled cords in-
crease the risk of electric shock.
5) When operating a power tool out-
doors, use an extension cord suit-
able for outdoor use.
II. GENERAL SAFE-
TY RULES
WARNING! Read all instructions
Failure to follow all instructions listed
below may result in electric shock, fire
and/or serious injury. The term “power tool”
in all of the warnings listed below refers to
your main operated (corded) power tool
and battery operated (cordless) power tool.
Use of a cord suitable for outdoor use
reduces the risk of electric shock.
-
3
-
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
3
2011-2-17
11:48:01
2) Do not use the power tool if the
switch does not turn it on and off.
Any power tool that cannot be con-
trolled with the switch is dangerous
and must be repaired.
3) Disconnect the plug from the pow-
er source and/or the battery pack
from the power tool before making
any adjustments, changing acces-
sories, or storing power tools.
Such preventive safety measures
reduce the risk of starting the pow-
er tool accidentally.
Personal Safety
1) Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the influence
of drugs, alcohol or medication.
A moment of inattention while oper-
ating power tools may result in per-
sonal injury.
2) Use safety equipment. Always
wear eye protection.
Safety equipment such as dust
mask, non-skid safety shoes, hard
hat, or hearing protection used for
appropriate conditions will reduce
personal injuries.
4) Store idle power tools out of the
reach of children and do not al-
low persons unfamiliar with the
power tool or these instructions
to operate the power tool.
3) Avoid accidental starting. Ensure
the switch is in the off position
before plugging in.
Power tools are dangerous in the
hands of untrained users.
5) Maintain power tools. Check for
misalignment or binding of mov-
ing parts, breakage of parts and
any other condition that may af-
fect the power tools operation. If
damaged, have the power tool re-
paired before use.
Many accidents are caused by
poorly maintained power tools.
6) Keep cutting tools sharp and clean.
Properly maintained cutting tools
with sharp cutting edges are less
likely to bind and are easier to con-
trol.
7) Use the power tool, accessories
and tool bits etc. in accordance
with these instructions and in the
manner intended for the particu-
lar type of power tool, taking into
account the working conditions
and the work to be performed.
Use of the power tool for operations
different from those intended could
result in a hazardous situation.
Carrying power tools with your fin-
ger on the switch or plugging in the
power tools that have the switch on
invites accidents.
4) Remove any adjusting key or
wrench before turning the power
tool on.
A wrench or a key left attached to a
rotating part of the power tool may
result in personal injury.
5) Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
6) Dress properly. Do not wear
loose clothing or jewelry. Keep
your hair, clothing and gloves
away from moving parts.
Loose clothes, jewelry or long hair
can be caught in moving parts.
7) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of these devices can reduce
dust related hazards.
Battery Tool Use and Care
1) Ensure the switch is in the off posi-
tion before inserting battery pack.
Inserting battery pack into pow-
er tools that have the switch on in-
vites accidents.
Power Tool Use and Care
1) Do not force the power tool. Use
the correct power tool for your ap-
plication.
2) Recharge only with the charger
specified by the manufacturer.
A charger that is suitable for one type
of battery pack may create a risk of fire
when used with another battery pack.
The correct power tool will do the
job better and safer at the rate for
which it was designed.
-
4
-
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
4
2011-2-17
11:48:01
3) Use power tools only with specif-
ically designated battery packs.
Use of any other battery packs
may create a risk of injury and fire.
4) When battery pack is not in use,
keep it away from other metal ob-
jects like paper clips, coins, keys,
nails, screws, or other small metal
objects that can make a connection
from one terminal to another.
Shorting the battery terminals to-
gether may cause burns, or a fire.
5) Under abusive conditions, liq-
uid may be ejected from battery;
avoid contact. If contact acciden-
tally occurs, flush with water. If
liquid contacts eyes, additionally
seek medical help.
6) Do not operate the Forward/Reverse
lever when the trigger switch is on.
The battery will discharge rapidly
and damage to the unit may occur.
7) When storing or carrying the tool,
set the Forward/Reverse lever to
the center position (switch lock).
8) Do not strain the tool by hold-
ing the speed control trigger half-
way (speed control mode) so that
the motor stops. The protection cir-
cuit will activate and may prevent
speed control operation. If this hap-
pens, release the speed control
trigger and squeeze again for nor-
mal operation.
9) Be careful not to get dust inside the
chuck.
10) Do not touch the rotating parts to
avoid injury.
Liquid ejected from the battery may
cause irritation or burns.
11) Do not use the tool continuously for a
long period of time. Stop using the tool
from time to time to avoid temperature
rise and heat overload of the motor.
12) Do not drop the tool.
Service
1) Have your power tool serviced by
a qualified repair person using
only identical replacement parts.
This will ensure that the safety of
power tool is maintained.
13) Wear dust mask, if the work causes
dust.
14) During charging, the charger may be-
come slightly warm. This is normal.
Do NOT charge the battery for a long
period.
III. SPECIFIC SAFE-
TY RULES
Symbol
meaning
1) Wear ear protectors. Exposure to
noise can cause hearing loss.
2) Use auxiliary handles supplied
with the tool. Loss of control can
cause personal injury.
3) Hold power tools by insulated
gripping surfaces when perform-
ing an operation where the cutting
tool may contact hidden wiring.
Contact with a “live” wire will make
exposed metal parts of the tool
“live” and shock the operator.
4) Be aware that this tool is always in
an operating condition, since it does
not have to be plugged into an elec-
trical outlet.
V
Volts
Direct current
No load speed
n0
Revolutions or
reciprocation per minutes
… min-1
Electrical capacity of
battery pack
Ah
Forward rotation
Reverse rotation
Rotation with hammering
Rotation only
5) If the bit becomes jammed, imme-
diately turn the trigger switch off
to prevent an overload which can
damage the battery pack or mo-
tor. Use reverse motion to loosen
jammed bits.
To reduce the risk of
injury user must read and
understand instruction
manual.
-
5
-
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
5
2011-2-17
11:48:02
7) An extension cord should not be
used unless absolutely necessary.
Use of improper extension cord
could result in a risk of fire and
electric shock. If extension cord
must be used, make sure:
a. that pins on plug of extension
cord are the same number, size
and shape as those of plug on
charger.
WARNING:
Some dust created by power sand-
ing, sawing, grinding, drilling, and
other construction activities contains
chemicals known to the State of Cal-
ifornia to cause cancer, birth defects
or other reproductive harm. Some
examples of these chemicals are:
* Lead from lead-based paints
* Crystalline silica from bricks and
cement and other masonry prod-
ucts
b. that extension cord is proper-
ly wired and in good electrical
condition.
c. that wire size is large enough
for ampere rating of charger as
specified below.
* Arsenic and chromium from chem-
ically-treated lumber.
To reduce your exposure to these
chemicals: work in a well ventilated
area, and work with approved safety
equipment, such as dust masks that
are specially designed to filter the
microscopic particles.
RECOMMENDED MINIMUM AWG SIZE OF
EXTENSION CORDS FOR
BATTERY CHARGERS
AC Input Rating. Amperes AWG Size of Cord
Equal to or
greater than
0
But less
than
2
Length of Cord, Feet
25 50 100 150
18 18 18 16
IV. FOR BATTERY
CHARGER &
8) Do not operate charger with dam-
aged cord or plug replace them
immediately.
9) Do not operate charger if it has re-
ceived a sharp blow, been dropped,
or otherwise damaged in any way;
take it to a qualified serviceman.
10) Do not disassemble charger; take it
to a qualified serviceman when ser-
vice or repair is required. Incorrect
reassembly may result in a risk of
electric shock or fire.
11) To reduce the risk of electric shock,
unplug charger from outlet before
attempting any maintenance or
cleaning.
12) The charger and battery pack are
specifically designed to work to-
gether. Do not attempt to charge
any other cordless tool or battery
pack with this charger.
13) Do not attempt to charge the battery
pack with any other charger.
BATTERY PACK
Important Safety Instructions
1) SAVE THESE INSTRUCTIONS
-
This manual contains important
safety and operating instructions for
battery charger.
2) Before using battery charger, read
all instructions and cautionary mark-
ings on (1) battery charger, (2) bat-
tery pack.
3) CAUTION - To reduce the risk of in-
jury, charge only Panasonic Battery
Pack as shown in last page.
Other types of batteries may burst
causing personal injury and damage.
4) Do not expose charger to rain or
snow.
5) To reduce the risk of damaging the
electric plug and cord, pull by plug
rather than cord when disconnect-
ing charger.
14) Do not attempt to disassemble the
battery pack housing.
15) Do not store the tool and battery
pack in locations where the tempera-
ture may reach or exceed 50°C
(122°F) (such a metal tool shed, or
a car in the summer), which can lead
to deterioration of the storage bat-
tery.
6) Make sure cord is located so that it
will not be stepped on, tripped over,
or otherwise subjected to damage
or stress.
-
6
-
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
6
2011-2-17
11:48:02
16) Do not charge battery pack when the
temperature is BELOW 0°C (32°F)
or ABOVE 40°C (104°F). This is very
important.
17) Do not incinerate the battery pack.
It can explode in a fire.
18) Avoid dangerous environment. Do not
use charger in damp or wet locations.
19) The charger is designed to operate
on standard household electrical
power only. Do not attempt to use it
on any other voltage!
20) Do not abuse cord. Never carry char-
ger by cord or yank it to disconnect
from outlet. Keep cord away from
heat, oil and sharp edges.
WARNING:
• Do not use other than the Panasonic
battery packs that are designed for
use with this rechargeable tool.
• Panasonic is not responsible for any
damage or accident caused by the
use of the recycled battery pack and
the counterfeit battery pack.
• Do not dispose of the battery pack in
a fire, or expose it to excessive heat.
• Do not drive the likes of nails into the
battery pack, subject it to shocks,
dismantle it, or attempt to modify it.
• Do not allow metal objects to touch
the battery pack terminals.
21) Charge the battery pack in a well
ventilated place, do not cover the
charger and battery pack with a
cloth, etc., while charging.
22) Use of an attachment not recom-
mended may result in a risk of fire,
electric shock, or injury to persons.
23) Do not short the battery pack. A bat-
tery short can cause a large current
flow, over heating and burns.
24) NOTE: If the supply cord of this appli-
ance is damaged, it must only be re-
placed by a repair shop appointed by
the manufacturer, because special
purpose tools are required.
25) TO REDUCE THE RISK OF ELEC-
TRIC SHOCK, THIS APPLIANCE
HAS A POLARIZED PLUG (ONE
BLADE IS WIDER THAN THE
OTHER).
• Do not carry or store the battery
pack in the same container as nails
or similar metal objects.
• Do not charge the battery pack in
a high-temperature location, such
as next to a fire or in direct sunlight.
Otherwise, the battery may over-
heat, catch fire, or explode.
• Never use other than the dedicated
charger to charge the battery pack.
Otherwise, the battery may leak,
overheat, or explode.
• After removing the battery pack from
the tool or the charger, always reat-
tach the pack cover. Otherwise, the
battery contacts could be shorted,
leading to a risk of fire.
• When the Battery Pack Has Deteri-
orated, Replace It with a New One.
Continued use of a damaged battery
pack may result in heat generation,
ignition or battery rupture.
This plug will fit in a polarized outlet
only one way. If the plug does not fit
fully in the outlet, reverse the plug. If
it still does not fit, contact a qualified
electrician to install the proper outlet.
Do not change the plug in any way.
V. ASSEMBLY
Attaching or Removing Bit
NOTE:
When attaching or removing a bit,
disconnect battery pack from tool
or place the switch in the center po-
sition (switch lock).
This tool is equipped with a keyless
drill chuck.
1. Attachment
Insert the bit and turn the lock collar
clockwise (looking from the front) to
tighten firmly until it stops clicking.
-
7
-
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
7
2011-2-17
11:48:02
Support handle
Place the support handle at your favorite
position and tighten the handle securely.
Lock collar
2. Removal
Turn the lock collar counterclock-
wise (looking from the front), then
remove the bit.
Tighten
Loosen
Always use the support handle to en-
sure operating safety.
NOTE:
If excessive play occurs in the
chuck, secure the drill in place and
open the chuck jaws by turn-
ing the lock collar and tighten
the screw (left-handed screw) with
a screwdriver by turning it counter-
clockwise (viewed from the front).
VI. OPERATION
[Main Body]
Switch Operation
1. The speed increases with the
amount of depression of the trigger.
When beginning work, depress the
trigger slightly to start the rotation
slowly.
2. A feedback electronic controller is
used to give a strong torque even
in low speed.
3. The brake operates when the trig-
ger is released and the motor stops
immediately.
Attaching or Removing Bat-
tery Pack
NOTE:
1. To connect the battery pack:
• When the brake operates, a brak-
ing sound may be heard. This is
normal.
• Sparks from the motor brush may
be visible through the body vent
holes on the back of the tool during
switching and braking due to the
load imposed on the motor. This
does not indicate a problem with
the tool.
Line up the alignment marks and at-tach
the battery pack.
Slide the battery pack until it locks into
position.
Alignment marks
2. To remove the battery pack:
Pull the button from the front to release
the battery pack.
Button
-
8
-
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
8
2011-2-17
11:48:02
CAUTION:
Set the clutch setting at this mark (
Switch and Forward/Reverse
Lever Operation
)
before actual operation.
Forward
Reverse
If the clutch handle cannot be set at
“drilling” or “hammering” mode af-
ter drilling with clutch function, set the
clutch handle at position 1 and oper-
ate the clutch for a second.
Switch lock
CAUTION:
Speed Selection
To prevent damage, do not operate
Forward/Reverse lever until the bit
comes to a complete stop.
Choose a low or high speed to suit the
use.
HIGH
LOW
Forward Rotation Switch
Operation
1. Push the lever for forward rotation.
2. Depress the trigger switch slightly
to start the tool slowly.
3. The speed increases with the amount
of depression of the trigger for efficient
tightening of screws and drilling. The
brake operates and the chuck stops
immediately when the trigger is released.
4. After use, set the lever to its center
position (switch lock).
The more the variable speed control trig-
ger is pulled, the higher the speed be-
comes.
WARNING:
• Do not inhale any smoke emitted
from the tool or battery pack as it
may be harmful.
CAUTION:
• Check the speed selector switch
before use.
Reverse Rotation Switch
Operation
1. Push the lever for reverse rotation. Check
the direction of rotation before use.
2. Depress the trigger switch slightly
to start the tool slowly.
3. After use, set the lever to its center
position (switch lock).
• Use at low speed when high torque
is needed during operation. (Using
at high speed when high torque
is required may cause a motor
breakdown.)
• Do not use the tool in a manner that
causes the motor to lock up. Doing
so may damage the tool and battery
pack, resulting in smoke or fire.
• Do not operate the speed selector
switch (LOW-HIGH) while pulling on
the speed control trigger. This can
cause the rechargeable battery to
wear quickly or damage the internal
mechanism of the motor.
Clutch Torque Setting
Adjust the torque to one of the
18 clutch settings or " " position
(EY7450).
Adjust the torque to one of the 18
clutch settings or " ", " " position
(EY7950).
NOTE:
Always make sure to stop operation
of the tool and disengage it from the
work, when you select Hammering
mode from Drilling mode or when you
shift to Drilling mode from Hammer-
ing mode by rotating clutch handle.
* See specifications for "MAXIMUM
RECOMMENDED CAPACITIES".
-
9
-
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
9
2011-2-17
11:48:02
CAUTION:
(1) LED light
• To prevent excessive temperature
increase of the tool surface, do not
operate the tool continuously using
two or more battery packs. The tool
needs cool-off time before switching
to another pack.
• Do not close up vent holes on the
sides of the body during operation.
Otherwise, the machine function is
adversely affected to cause a failure.
Before the use of LED
light, always pull the
power switch once.
Press
the LED light
button.
Thelightilluminateswith
very low current, and it
does not adversely af-
fect the performance of
the tool during use or its
battery capacity.
• Do NOT strain the tool (motor). This
may cause damage to the unit.
• Use the tool in such a way as to
prevent the air from the body vent
holes from blowing directly onto
your skin. Otherwise, you may get
burned.
CAUTION:
• The built-in LED light is designed
to illuminate the small work area
tempo-rarily.
• Do not use it as a substitute for a
regular flashlight, since it does not
have enough brightness.
Bit-locking Function
1. With the trigger switch not engaged
and a screwdriver bit locked in
place, the tool can be used as a
manual screwdriver (up to 40 N•m,
408 kgf-cm, 353 in-lbs).
• LED light turns off when the tool has
not been used for 5 minutes.
Caution: DO NOT STARE INTO BEAM.
Use of controls or adjustments or perfor-
mance of procedures other than those
specified herein may result in hazardous
radiation exposure.
There will be a little play in the
chuck, but this is not a malfunction.
2. This feature is handy for tightening
screws that require more torque
than the maximum torque of the
driver (position on the clutch), for
confirming the tightness of a screw or
to loosen an extremely tight screw.
(2) Overheat warning lamp
Off
(normal
operation)
Flashing:
Overheat
(battery)
Indicates operation has
been halted due to motor
or battery overheating.
Control Panel
To protect the motor or battery, be
sure to note the following when carry-
ing out this operation.
(3)
(1)
•
If the motor or battery becomes hot,
the protection function will be acti-
vated and the motor or battery will
stop operating. The overheat warning
lamp on the control panel illuminates
or flashes when this feature is active.
(2)
-
10
-
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
10
2011-2-17
11:48:03
• If the overheating protection feature
activates, allow the tool to cool thor-
oughly (at least 30 minutes). The
tool is ready for use when the over-
heat warning lamp goes out.
• Avoid using the tool in a way that
causes the overheating protection
feature to activate repeatedly.
Battery Pack Life
The rechargeable batteries have
a limited life. If the operation time
becomes extremely short after
recharging, replace the battery pack
with a new one.
Battery Recycling
•
If the tool is operated continuously un-
der high-load conditions or if it is used
in hot-temperature conditions (such as
during summer), the over-heating pro-
tection feature may activate frequently.
ATTENTION:
A Li-ion battery that is recyclable powers
the product you have purchased. Please
call 1-800-8-BATTERY for information on
how to recycle this battery.
• If the tool is used in cold-tempera-
ture conditions (such as during win-
ter) or if it is frequently stopped dur-
ing use, the overheating protection
feature may not activate.
(3) Battery low warning lamp
[Battery Charger]
Charging
Cautions
• If the temperature of the battery pack
falls approximately below −10°C (14°F),
charging will automatically stop to
prevent degradation of the battery.
Off
(normal
operation)
Flashing
(No charge)
Battery protection
feature active
• The ambient temperature range is
between 0°C (32°F) and 40°C (104°F).
If the battery pack is used when the
battery temperature is below 0°C
(32°F), the tool may fail to function
properly.
• When charging a cool battery pack
(below 0°C (32°F)) in a warm place,
leave the battery pack at the place and
wait for more than one hour to warm up
the battery to the level of the ambient
temperature.
• Cool down the charger when
charging more than two battery packs
consecutively.
• Do not insert your fingers into contact
hole, when holding charger or any other
occasions.
Excessive (complete) discharging of
lithium ion batteries shortens their
service life dramatically. The driver in-
cludes a battery protection feature
designed to prevent excessive dis-
charging of the battery pack.
• The battery protection feature ac-
tivates immediately before the bat-
tery loses its charge, causing the
battery low warning lamp to flash.
• If you notice the battery low warning
lamp flashing, charge the battery
pack immediately.
To prevent the risk of fire or
damage to the battery charger.
• Do not use power source from an
engine generator.
• Do not cover vent holes on the
charger and the battery pack.
• Unplug the charger when not in
use.
-
11
-
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
11
2011-2-17
11:48:04
The orange standby lamp will be
Li-ion Battery Pack
flashing until the battery cools down.
Charging will then begin automatically.
NOTE:
Your battery pack is not fully charged
at the time of purchase. Be sure to
charge the battery before use.
4. The charge lamp (green) will
flash slowly once the battery is
approximately 80% charged.
5. When charging is completed, the
charging lamp in green color will turn
off.
Battery charger
1. Plug the charger into the AC outlet.
6. If the temperature of the battery pack
is 0°C or less, charging takes longer
to fully charge the battery pack than
the standard charging time.
2. Insert the battery pack firmly into the
charger.
1. Line up the alignment marks and
place the battery onto the dock on the
charger.
Even when the battery is fully
charged, it will have approximately
50% of the power of a fully charged
battery at normal operating
2. Slide forward in the direction of the
arrow.
temperature.
Alignment marks
7. Consult an authorized dealer if the
charging lamp (green) does not turn
off.
8. If a fully charged battery pack is
inserted into the charger again, the
charging lamp lights up. After several
minutes, the charging lamp in green
color will turn off.
3. During charging, the charging lamp
will be lit.
When charging is completed, an
internal electronic switch will
automatically be triggered to prevent
overcharging.
9. Remove the battery pack while the
battery pack release button is held
up.
•
Charging will not start if the
battery pack is warm (for example,
immediately after heavy-duty
operation).
Battery pack
release button
LAMP INDICATIONS
Charging is completed. (Full charge.)
Battery is approximately 80% charged.
Now charging.
Charger is plugged into the AC outlet. Ready to charge.
Charging Status Lamp.
Left: green Right: orange will be displayed.
(Green)
(Orange)
Battery pack is cool.
The battery pack is being charged slowly to reduce the load on the battery.
Battery pack is warm.
Charging will begin when temperature of battery pack drops. If the temperature of the
battery pack is -10° or less, the charging status lamp (orange) will also start flashing.
Charging will begin when the temperature of the battery pack goes up"
Charging is not possible. Clogged with dust or malfunction of the bat-
tery pack.
Turn off
Lit
Flashing
-
12
-
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
12
2011-2-17
11:48:05
VII. MAINTENANCE
Use only a dry, soft cloth for wiping the unit. Do not use a damp cloth, thinner, benzine,
or other volatile solvents for cleaning.
In the event that the inside of the tool or battery pack is exposed to water, drain and
allow to dry as soon as possible. Carefully remove any dust or iron filings that collect
inside the tool. If you experience any problems operating the tool, consult with a repair
shop.
<VIII. ACCESSORIES>
Use only bits suitable for size of drill's chuck.
IX. APPENDIX
MAXIMUM RECOMMENDED CAPACITIES
Model
EY7450
EY7950
Machine screw
Wood screw
Self-drilling screw
For Wood
M8
ø 10 mm or ø 6.8 mm
ø 6 mm
Screw
driving
ø 36 mm
For Metal
ø 13 mm
Drilling
For Masonry
ø 13 mm
X. SPECIFICATIONS
MAIN UNIT
Model
EY7450
EY7950
Motor voltage
Low
18 V
0 - 430 min-1
0 - 1650 min-1
No load speed
High
Low
---
---
1800 - 7740 min-1
Blows Rate Per Minute
High
6840 - 29700 min-1
ø 1.5 mm - ø 13 mm (1/16 - 1/2)
Approx 1.0 N m - 6.9 Nm
218 mm (8 - 9/16") 235 mm (9 - 1/4”)
2.15 k (4.7 lbs) 2.3 k (5.0 lbs)
Chuck capacity
Clutch torque
Overall length
Weight (with battery pack)
BATTERY PACK
Model
EY9L50
Li-ion
Storage battery
Battery voltage
18 V DC (3.6V x 10 cells)
-
13
-
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
13
2011-2-17
11:48:05
BATTERY CHARGER
Model
EY0L81
Electrical rating
See the rating plate on the bottom of the charger.
EY9L50
Charging time
Usable: 50 min
Full: 65 min
NOTE: This chart may include models that are not available in your area.
Please refer to the latest general catalogue.
NOTE: For the dealer name and address, please see the included warranty card.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is en-
couraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the re-
ceiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, install and use in accordance with pro-
vided instructions. Use only the battery pack specified in the instructions. Any changes
or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions: (1) This device may not cause harmful interference, and (2) this de-
vice must accept any interference received, including interference that may cause un-
desired operation.
This Class B digital apparatus complies with Canadian ICES-003.
-
14
-
Download from Www.Somanuals.com. All Manuals Search And Download.
EY7442_7450_7950(UL).indb
14
2011-2-17
11:48:05
|