P S40T
User Ma n u a l
Rev. 003
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents..................................................iii
Printing a Test Page............................................. 28
Printer Setup......................................................... 31
Printing the Printer Setup Forms .................. 31
Filling in the Printer Setup Forms ................ 34
Reading the Preprinted Forms ....................... 34
Printer Setup Flow Chart ............................... 35
Setup Parameters............................................. 36
Offset Adjustments........................................... 48
Troubleshooting................................................... 52
Clearing Paper J ams ........................................ 52
Print Quality Problems .................................... 55
Hexadecimal Dump .......................................... 56
Paper Specifications............................................ 57
Cut Sheets ......................................................... 55
Fanfold Paper .................................................... 59
Technical Specifications ..................................... 60
FCC Notes............................................................. 63
Canadian D.O.C. Radio Interference
Printer Presentation...............................................1
Unpacking the Printer............................................3
Printer Parts............................................................4
Front View...........................................................4
Rear View ............................................................ 5
Printer Installation..................................................6
Choosing a Suitable Location............................ 6
Installing the Paper Stand ................................ 7
Installing the Power Cable..............................10
Installing the Ribbon Cartridge......................12
Paper Handling.....................................................14
Loading Paper ...................................................14
Loading Cut Sheet and Multiparts ............. 14
Loading Fanfold Paper ................................. 17
The Operator Panel..............................................20
Function keys .................................................... 20
Leds .................................................................... 23
Software Driver Selection ...................................24
Connection to the Host........................................25
Setting the Interface Parameters ...................26
Parallel Interface ..........................................26
Serial Interface..............................................26
Regulation............................................................. 63
EEC Regulations..................................................63
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Presentation
This dot-matrix printer is a multi-purpose printer for counter applications. Its compact structure
is designed to be integrated in an ergonomic environment. The printer provides a high level of
reliability, form-handling accuracy and data integrity. Its main features are:
· Printing on d iffer en t typ es p a p er : cut sheets, multipart and fanfold paper
· High print pressure for m u lt ip a r t d ocu m en t s: 1 original plus 8 copies in accurate printing
· H igh p r in t q u a lit y supplied by a 24 wire print head
· H igh r elia b ilit y p a p er h a n d lin g
The straight paper path allows the printing on particular documents such as multipart forms.
· Au t om a t ic p a p er t h ick n ess a d ju st m en t
The print head detects automatically the paper thickness for correct printing on any type of
document.
· E a sy p a p er h a n d lin g
The cut sheets are placed on the front table by the operator and the printer loads it without any
other user intervention. The paper ejection towards the front or the rear of the printer allows an
easy access to the printed document.
For the fanfold paper the printer offers the zero tear -off feature, which allows a paper handling
without waste of paper, and the paper parking feature.
· Au t om a t ic sw it ch in g b et w een cu t sh eet s a n d fa n fold p a p er
If the paper path is empty (i.e. the fanfold paper is in the first line position), when inserting a
cut sheet into the printer, it is automatically loaded after the printer automatically parked the
fanfold paper. The fanfold paper can then be loaded again simply pressing the LOAD/PARK key.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
· Au t om a t ic d ocu m en t a lign m en t feature
The printer checks automatically the alignment of the top margin and the left margin of the
document and adjusts it, if necessary. The printout is therefore performed correctly
independently from the paper loading position.
· St or a ge of fou r com p let e con figu r a t ion s for instant recall
· St a n d a r d p a r a llel a n d ser ia l in t er fa ce and automatic switch-over function.
· E a sy p r in t er set u p
· Supported em u la t ion s: IBM Proprinter XL24E, XL24E AGM, 2390+ and Epson 570
· Ba r cod e r ea d er in both horizontal and vertical print mode (factory installable option).
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking the Printer
Together with the printer the following items are included in the shipment box:
Notify any damage to your supplier.
· Paper stand
· Ribbon cartridge
· Power cable
· CD-ROM with the printer documentation and drivers.
Always keep the packing material in a safe place as you must repack the printer into it, when
you need to move it.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Parts
Never remove any printer part unless it is expressly indicated in this manual.
Front View
Operator Panel
Printer Cover
Paper Stand
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear View
Rear cover
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Installation
Choosing a Suitable Location
Consider the following points when you choose the location for your printer:
· The distance between the printer and the host computer must not exceed the length of the
interface cable;
· The location must be sturdy, horizontal and stable;
· Your printer must not be exposed to direct sunlight, extreme heat, cold, dust or humidity;
· You need an AC power outlet compatible with the plug of the printer’s power cord. The voltage
of the outlet must match the voltage shown on the printer’s Name Plate;
· When printing on standard paper formats, the paper is partially ejected on the rear side of the
printer. Make sure that behind the printer there is sufficient clearance to correctly move the
paper;
· Make sure that behind the printer there is sufficient clearance to easily load the fanfold paper;
· Make sure that the power and interface cables do not hamper the fanfold paper while it is
loaded into the printer.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Paper Stand
1. Open the printer cover.
2. Match the hooks on the lower side of the
paper stand with the clefts on the printer
front part.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Holding the paper stand oblique insert the hooks into the printer clefts.
4. Lower the paper stand to horizontal position making sure that the two holders on both sides are
correctly inserted into the corresponding slots. Press the paper stand down until it clips into
place.
5. Close the printer cover.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Power Cable
1. Find the power cable connector and the rating plate on the rear side of the printer.
Make sure that your power supply matches the power rating of the printer.
In case the power rating does not correspond DO NOT CONNECT THE PRINTER TO THE
MAINS. Consult your dealer for help.
Always use a grounded outlet.
2. Insert the power cable into the
connector on the printer and the other
end into a convenient mains outlet.
3. Press the key on the operator panel
to power the printer on.
LQ
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Ribbon Cartridge
To install the ribbon cartridge, the printer must be powered on.
1. Remove the cartridge from its bag. Turn
the tension knob in the direction of the
arrow to tighten the ribbon.
2. Open the printer cover, the print head
moves to the ribbon installation position.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Hold th e ribbon cartridge slightly inclined
with the ribbon mask in front of the print
head.
4. Insert the ribbon cartridge into the print
head carriage, leading the cartridge pins
into the fixing guides. In this way you
assure the correct ribbon mask position in
front of the print head. Push the cartridge
onto the print carriage until it clicks into
place.
5. Turn the tension knob in the direction of the arrow to tighten the ribbon.
6. Close the printer cover.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper Handling
This printer is designed for versatile an reliable paper handling. The flat-bed mechanism allows
the handling of special documents, such as multiple invoices, postcards, labels and tickets.
The print head detects the paper edges automatically, the sheet can therefore be inserted in any
position within the detection area according to the rules described in the following paragraph.
The paper alignment sensors determine the alignment of the upper and left paper margins,
adjusting them if necessary.
The print head determines the thickness of the documents and matches its position.
Loading Paper
Loading Cut Sheet and Multiparts
· The inserted documents must not have folds, tears, pins, clips, staples or any foreign material.
Clip
Pin
Tear
Staple
Fold
Foreign
material
If you insert damaged documents or paper with foreign material, you can seriously damage the printer.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
When inserting the paper into the printer, keep the following points in mind:
· The document may not exceed the limits of the paper stand.
Left Limit
Right Limit
· The documents having a width of at least 90 mm must be inserted on the left hand side over th e
grooved area on the paper stand.
The documents must cover the whole grooved area, otherwise the printer will not accept the
paper.
NO
OK
15
Download from Www.Somanuals.com. All Manuals Search And Download.
·
To load the documents having a width of less than 90 mm:
-
-
make sure that in the program menu the MANUALLOADINGitem is enabled.
hold the paper against the left paper guide of the paper support while inserting it into the
printer
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading Fanfold Paper
The fanfold paper is loaded form the rear of the printer.
1. Lower the two levers of the rear printer cover and unhook it from the printer.
2. Unhook the right tractor moving the tractor lever towards the outside of the printer.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Open the two tractor covers.
4. Insert the perforation of the fanfold paper on the left paper tractor. Close the tractor door.
Insert the paper on the right paper tractor and close the tractor door.
The leading edge of the inserted paper should not exceed the tractors.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure, that the paper is inserted correctly (straight).
5. Move the right paper tractor towards the right to slightly tighten the paper. Lock the tractor in
that position moving the tractor lever towards the inside of the printer.
Make sure, that the paper is not too taught, otherwise it may tear.
6. Hook the rear tractor cover into the corresponding slots (1) and push it against the printer until
both rear tractor levers (2) firmly hook into the printer.
2
1
7. Press LOAD/PARK to load the paper into the printer.
To remove the paper from the printer follow the above sequence backwards.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
The Operator Panel
The operator panel is located on the front left side of the printer and is composed of function keys
and leds with which you can easily check the printer status and select the functions as described
below:
MICROFEED
P1
P2
P3
LF
FF
LOAD
PARK
P4
PROGRAM
LQ
ONLINE
Function Keys
Turns the printer on or off.
To turn the printer off, this key must be pressed for at least 3 seconds.
Toggles between Letter Quality and Draft printing mode.
LQ
This key is active when the printer is offline, or when the printer is online and no print
data is in the buffer.
When pressed while powering the printer on, selects the printer setup mode. See
“Printer Setup ” later in this manual.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
LOAD
PARK
If the paper path is empty, the fanfold paper is loaded into the printer (LOAD
function). This function is performed when the printer is online or offline.
If paper is loaded in the printer, pressing this key, the PARK function is performed:
· a single sheet is loaded in the printer, it is ejected;
· if the fanfold paper is loaded in the printer, it is parked if the printer is offline
(ON LINE indicator off) or when the printer is online (ON LINE indicator on) and
there are no data to be printed.
The PARK key has different effects depending on the selection for the PARK
MODE item in the Program Setup. See the description of this item later in this
manual.
•
¯
Moves the fanfold paper forward in microsteps or continuously when keeping the
key pressed.
This key is enabled when the printer cover is open.
Moves the fanfold paper backwards in microsteps or continuously when keeping
the key pressed.
This key is enabled when the printer cover is open.
LF
FF
Moves the paper one line.
If fanfold paper is loaded, the key moves it forward one page.
If a single sheet is loaded, it is moved forward for the selected page length.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAM
Selects one of the available configurations (P1, P2, P3 and P4 or a configuration
couple P1/P3 or P2/P4) if the PROGRAM LOCKEDparameter is not enabled.
This key is active, when the printer is offline or when the printer is online and no
print data are in the buffer.
When pressed while powering the printer on, selects the offset adjustment page.
See “Offset Adjustment ” later in this manual.
ON LINE
Toggles the printer between online and offline status.
When pressed while powering the printer on, selects the Self Test printout. See
“Printing a Test Page ” in this manual.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Leds
POWER
On, if the printer is powered on.
LQ
On, if the Letter Quality mode is selected.
P1, P2,
P3, P4
Indicate the currently select ed configuration both in normal printing mode and
during the Printer Setup procedure. See “ Printer Setup ” later in this section.
If the INTERFACE TYPE function is set to auto+blink, when line 1 (parallel
interface) is selected for data transmission, the P1 indicator blinks.
INTERFACE TYPE
auto+blink
, when line 2 (serial interface)
If the
function is set to
is selected for data transmission, the P2 indicator blinks.
In case of fault condition P1, P2, P3 and P4 blink.
On, if the printer is online.
ON LINE
Off, if the printer is offline.
Blinks, when receiving printing data from host.
LQ P1 P2 P3 P4 ON LINE
and
In case of a printer fault during the initialization of the
,
,
,
,
indicators blink continuously. Turn the printer off and on again. If the problem is not solved,
call Technical Support .
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Software Driver Selection
At this point it is necessary to configure your printer for your application package. The
installation procedures depend upon the host environment.
Included with the printer you received a CD-ROM containing the printer drivers for the Windows
environment. This printer supports the Plug&Play facility in the Windows95/98 ® environment.
If you want to install the printer in the Windows environment, insert the CD-ROM and follow the
instructions.
The printer drivers of all Output Technology printers can be found at the Internet Address
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to the Host
This printer can be connected to the host by means of a parallel standard Centronics or
bidirectional IEEE 1284 type interface or by means of the serial RS232C interface.
Proceed as follows:
1. Make sure that both the host and the printer are turned off.
With the help of the following figure identify the connector for the interface you want to connect
and insert the cable firmly into it.
2.
Fix the parallel interface cable by means of the corresponding hooks or the serial cable
tightening the screws on either side of the connector.
3.
SERIAL
(Line 2)
PARALLEL
(Line 1)
Make sure, that the interface cables do not hamper the fanfold paper while it is loaded into the
printer.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Interface Parameters
Parallel Interface
The parameters set for the parallel interface match most of the most common environments and
the printer can be used immediately after the connection to the host.
In case you need to modify the standard parameters see “ Printer Setup ” later in this section.
Serial Interface
Because of the great variety of the possible connection configurations, when you use the serial
interface you will need to set the parameters accordingly.
To assure the correct functioning of the printer connected through the serial interface, the
transmission parameters set for the printer must match the values set for the host. Check the
interface settings on the host and proceed as follows:
LQ
1. Press the
key while powering the printer on and keep it pressed until all leds turn briefly on.
The printer enters the Setup mode.
2. Insert a blank sheet of paper (A4 or Letter format). The printer loads the sheet and stops. The
P1, P2, P3 and P4 leds are lit.
PROGRAM
P1, P2, P3
P4
and leds are unlit.
3. Press the
key once. The
4. Press the LQ key. The printer prints the first configuration sheet.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
5. To change the values of the serial interface parameters, fill in the marker ( ) beside the value
you want to set with a black or blue ball-point pen or a fiber-pen.
Do not use pencils.
WORD LENGTH
BAUD RATE
PARITY BIT
( )
( )
disabled *
enabled
( )
( )
disabled *
enabled
( )
DTR
( )
( )
XON/XOFF* XON/XOFF + DTR
If more than one value is set for a parameter, the printer ignores these parameters and
maintains the currently set value.
Do not fill in the marker beside the title of the preprinted form, otherwise the printer will not be
able to read that page.
6. Once the serial interface parameters have been assigned, insert the sheet back into the printer.
7. The printer reads the selected values on the configuration sheet and sets them. The settings
are confirmed by a # symbol printed on the left of the corresponding marker.
The printer then returns to normal functioning mode.
For a complete description of the printer setup procedure see the paragraph “Printer Setup”
later in this manual.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing a Test Page
It is now useful to test, if the printer has been correctly installed. For this purpose print the self
test page as follows.
1. Press the ON LINE key while powering the printer on and hold the key pressed until all leds turn
briefly on .
2. Insert a single sheet in A4 or Letter format.
The printer prints the Self-Test page. Check that the printout is correct. The following printout
example shows also the printer setup default values.
ELF EST
S
T
Code Version Vx.x xxxxxxxx CharGen:xxxxxxxx ver. x.xx
PS40T:
CONFIGURATION SETUP
PROGRAM
progr.1
no
INTERFACE TYPE
INPUT BUFFER
IGNORE PE
automatic
16 Kb
enabled
PROGRAM LOCKED
ERROR BUZZER
JOB BUZZER
SECURITY MODE
AUTO GAP OFFSET
GET EDGE QUOTE
SKIP PERFORATION
TEAR ADJUST
1 beep
no beep
enabled
+0.000 mm
1/2”
AUTOFEED SIGNAL disabled
SLCT-IN SIGNAL
BUFFER CONTROL
ROBUST XON
WORD LENGTH
BAUD RATE
disabled
XON/XOFF
enabled
8 bit
9600 bps
none
disabled
+0,00 mm
PARITY BIT
28
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAM SETUP
PROGRAM 1
IBM XL24E
Draft
10 cpi
6 lpi
no lock
A4
PROGRAM 2
EPSON 570
Draft
10 cpi
6 lpi
no lock
A4
PROGRAM 3
IBM XL24E
Draft
10 cpi
6 lpi
no lock
#lines
72
PROGRAM 4
EPSON 570
Draft
10 cpi
6 lpi
no lock
#lines
72
PROTOCOL
FONT
HORIZONTAL PITCH
VERTICAL PITCH
LOCK
FORM LENGTH
0
0
LEFT MARGIN
RIGHT MARGIN
TOP MARGIN
0
96
0
0
96
0
0
96
0
0
96
0
BOTTOM MARGIN
IBM C-SET
IBM COMPRESS
EPSON C-SET
NATION C-SET
CODE PAGE
0
0
0
0
IBM set 1
17.1 cpi
graphic
USA
IBM set 1
17.1 cpi
Graphic
USA
IBM set 1
17.1 cpi
graphic
USA
IBM set 1
17.1 cpi
graphic
USA
CP437
CP437
CP437
CP437
LINE MODE
LF=LF, CR=CR LF=LF, CR=CR LF=LF, CR=CR LF=LF, CR=CR
WRAP MODE
autowrap
Autowrap
autowrap
autowrap
SLASHED ZERO
PRINT DIRECTION
EJECT ON FF
CUT SHEET EJECT
PARK MODE
no
No
no
no
sw control
yes
on front
manual imm.
sw control
Yes
On front
manual imm.
sw control
yes
on front
manual imm.
sw control
yes
on front
manual imm.
TEAR MODE
manual
Manual
manual
manual
MANUAL LOADING
ALIGN MODE
disabled
fast
Disabled
Fast
disabled
fast
disabled
fast
GAP MODE
auto
Auto
auto
auto
AUTO EMPHASIZED
VERT.POS 1/10”
VERT.ADJ 1/60”
HORIZ.POS 1/10”
HORIZ.ADJ 1/60”
no autoEM
no autoEM
no autoEM
no autoEM
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
29
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Setup
The default configuration of this printer matches most of the commonly used environments, but it
may be necessary to change some printer parameters. For this purpose it is necessary to use the
preprinted forms to be used with the printer in configuration mode.
The following is the complete description of the Setup Procedure.
The detailed description of the parameters that can be set on the various preprinted forms are
described in the “Setup Parameters” paragraph, later in this manual.
To enter the Printer Setup Mode press and hold the LQ key for at least 1 second while powering
the printer on. The printer enters the Setup Mode.
Printing the Printer Setup Forms
If you already have the preprinted forms for the printer setup, go to “Filling in the Printer Setup
Forms” later in this manual.
Insert a blank sheet of paper (A4 or Letter format). The printer loads the sheet and stops. The P1,
P2, P3 and P4 leds are lit.
The ON LINE, PROGRAM and LQ keys are enabled.
LQ
If the
key is pressed immediately after the printer enters in Setup Mode, all printer setup
modules are printed.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ON LINE
If you p r ess th e
k ey:
· the printer self-test is printed. See “Printing a Test Page ” before in this manual. In this way it
is possible to check the current printer parameters.
· once the self-test is finished, the printer remains in Setup Mode.
If you p r ess th e PROGRAM k ey:
· the Px leds change and you can select the Setup Page you want to print as follows:
P1
P2
P3
P4
P1
P2
P3
P4
P1
P2
P3
P4
P1
P2
P3
P4
P1
P2
P3
P4
P1
P2
P3
P4
Program 2 page
Program 3 page
Program 4 page
All setup pages
Configuration page
Program 1 page
= lit
= unlit
The printer setup forms contain all printer parameters and the values that can be set. The
current value is indicated by an asterisk (*).
For a detailed description of the parameters and the settings see “Setup Parameters” later in
this manual.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Each printer setup form is identified by a marker in the upper left corner of the page as follows:
Configuration Setup
Program 1
Program 3
Program 2
Program 4
LQ
If you p r ess th e
k ey:
The printing of the printer setup forms starts. The forms are printed according to the selection
PROGRAM
made with the
If you select one of the Program couples P1/P3 or P2/P4 you can define one parameters set for
P1 P2
define the values for printing on cut sheets,
key.
printing on cut sheets and one for fanfold.
and
whereas P3 and P4 define the printing parameters for the fanfold paper.
The program couples may be selected only if the same emulation is selected for the two
programs.
The selection of the Program Setup is made simply by pressing the PROGRAM key. When passing
from one Program Setup to another, the printer resets before setting the parameters as defined in
the new program setup.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Filling in the Printer Setup Forms
To change the values of the parameters, fill in the marker ( ) beside the value you want to set with
a black or blue ball-point pen or a fiber-pen.
Do not use pencils.
AUTOFEED SIGNAL ( )
( )
disabled * enabled
SLCT-IN SIGNAL
( )
( )
disabled * enabled
BUFFER CONTROL ( )
( )
( )
DTR
XON/XOFF*XON/XOFF +
If more than one value is set for a parameter, the printer ignores these parameters and
maintains the currently set value.
Do not fill in the marker beside the title of the preprinted form, otherwise the printer will not be
able to read that page.
Reading the Preprinted Forms
When the Printer Setup Forms have been filled in, insert them back into the printer. The printer
is able to recognize the Setup Forms by means of the markers on these pages. The printer reads
the values marked for the various parameters and configures the printer accordingly.
The settings are confirmed by a # symbol printed to the left of the corresponding marker.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Setup Flow Chart
+
Normal Mode
Printer Powered-off
LQ
P1
P2
P3
P4
PROGRAM
ONLINE
LQ
S e l f T e s t
P1
P2
P3
P4
PROGRAM
LQ
+
!
P1
P2
P3
P4
+
+
+
PROGRAM
LQ
P1
P2
P3
P4
PROGRAM
LQ
P1
P2
P3
P4
PROGRAM
LQ
P1
P2
P3
P4
PROGRAM
LQ
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Parameters
The following is a listing of the setup parameters.
Configuration Sheet
Setup Parameter
Values
Description
RESTORE TO MFG no
all
The selected values are not set to factory defaults.
The values set in all printer setups are reset to factory
default values.
config
The values set in the configuration setup are reset to
factory default values.
prog.1, prog. 2,
prog.3, prog 4
The values set in the corresponding program setup are
reset to the factory default values.
PROGRAM
progr.1, progr.2, progr.3, Defines the default Program Setup or Setup couple. The
progr.4, progr.1/3,
progr.2/4
program couples may be selected only if the same
emulation has been selected for the two setups.
PROGRAM
LOCKED
no, yes
Locks the program setup selection. In case the lock is
the program setup cannot be changed by pressing the
PROGRAM key.
yes
ERROR BUZZER
JOB BUZZER
1 beep, no beep
Selects the behavior of the buzzer in case of an error.
no beep, 1 beep,
continuous
Selects the behavior of the buzzer when a new print job is
started: no signal (
continuous signal (
), one beep ( ) or a
1 beep
no beep
).
continuous
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Parameter
Values
Description
INTERFACE TYPE parallel, serial, automatic, Selects the interface type. In case of ‘automatic’ the
auto+blink interface type is selected by the printer depending on data
coming from host. When the item is selected,
auto+blink
the P1 and P2 leds blink to indicate which interface is
selected: P1 blinks when the serial interface is selected,
whereas P2 blinks when the parallel interface is selected.
INPUT BUFFER
IGNORE PE
1 Kb, 8 Kb, 16 Kb, 32 Kb Selects the buffer size.
enabled, disabled
disabled, enabled
disabled, enabled
Selects whether the printer signals the paper empty
condition ( ) or not ( ).
disabled
enabled
AUTOFEED
SIGNAL
The parallel interface uses (
) or does not use
enabled
(
) the AUTOFEED signal.
disabled
SLCT-IN SIGNAL
The parallel interface uses (
) or does not use
enabled
) the SELECT-IN signal.
(
disabled
BUFFER
CONTROL
DTR+SRTS, SRTS,
XON/XOFF,
Selection of the buffer protocol.
XON/XOFF+DTR+SRTS
ROBUST XON
WORD LENGTH
BAUD RATE
PARITY BIT
enabled, disabled
7 bit, 8 bit
Perform the Robust XON (
) or not (
).
disabled
enabled
Sets the number of the data bits.
Sets the data transfer rate.
600 - 38400 bps
Even, odd, none
Selects the parity control for the data.
SECURITY MODE enabled, disabled
Enables or disables the security actions that assure
protection against paper jams. If disabled, the paper
37
Download from Www.Somanuals.com. All Manuals Search And Download.
handling is faster.
Setup Parameter
Values
Description
AUTO GAP OFFSET -0,075 mm, -0.050 mm, Sets the automatic gap offset to one of the given values.
-0.025 mm,
+0.000 mm, +0.025
mm, +0.050 mm,
+0.075 mm, +0.100
mm
GET EDGE QUOTE 0/2”, 1/2”, 2/2”, 3/2”,
4/2”, 5/2”, 6/2”, 7/2”
Sets the position in which the left paper edge is checked. If
set to 0, the check is performed at the first line. The other
values correspond to the physical distance from the first line.
SKIP
disabled, enabled
If the passage of the paper perforation under the print head is
PERFORATION
critical, select
to avoid the paper being torn. The
enabled
print head lifts up during the paper passage. If disabled, the
print head stays in position.
TEAR ADJUST
-0,85 mm, -0,56 mm, - Sets the paper tear-off position by aligning the paper with the
0,28 mm, +0,00 mm,
+,28 mm +0,56 mm,
+0,85 mm
tear-off edge .
38
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAM 1
PROGRAM 3
PROGRAM 2
PROGRAM 4
Setup Parameter
Values
Description
PROTOCOL
EPSON 570, IBM XL24E,
IBM XL24E AGM, IBM 2390
Defines the printer protocol.
FONT
Draft, Courier, OCR-B,
Gothic, Prestige, Present,
OCR-A, Script, Boldface
Selects the font.
HORIZONTAL
PITCH
10 cpi, 12 cpi, 15 cpi, 17 cpi, Selects the character spacing in characters per inch
20 cpi
(cpi).
VERTICAL PITCH
LOCK
5 lpi, 6 lpi, 8 lpi,
Selects the line spacing in lines per inch (lpi).
no lock, font, hor. pitch,
font+hor. pitch
The following selections made via operator panel may be
locked: font, horizontal pitch (
), or both the
. The
hor.pitch
font and horizontal pitch (
.
font+hor pitch)
locked settings cannot be changed via software
commands.
FORM LENGTH
# lines, A4, letter, A5, legal
Sets the page length in number of lines or standard
formats A4, Letter, A5 or Legal. If you select
,
# lines
you must indicate the number of lines you want to set in
the scheme below this selection. The values range
between 0 and 255. To set the values combine the
39
Download from Www.Somanuals.com. All Manuals Search And Download.
numbers considering that the first line corresponds to the
hundreds, the second line to the tens and the third line to
the units. See the example below.
Example:
How to set the form length to 82 lines:
(
(
FORM LENGTH
( )
A4
( )
letter A5
( )
( )
legal
# lines
0
1
2
3
4
5
6
7
8
9
100 x
10 x
( )
( )
( )
( )
(
( )
( )
( )
( )
( )
( )
( )
( )
( )
( )
( )
( )
( )
(
(
1 x
( )
( )
(
( )
Setup Parameter
Values Description
LEFT MARGIN
10 x
1 x
Sets the left margin in number of columns. The values range between 0 and 90.
The physical position of margin depends on the current character spacing To
set the values combine the numbers considering that the first line corresponds
to the tens, the second line to the units. See the example below.
Example:
How to set the Left Margin to 20.
LEFT MARGIN
0
1
2
3
4
5
6
7
8
9
(
10 x
1 x
( ) ( )
( ) ( )
( ) ( ) ( ) ( ) ( )
(
(
(
( ) ( ) ( ) ( )
( ) ( ) ( ) ( ) ( )
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Parameter
Values Description
RIGHT MARGIN
100 x Sets the right margin in number of columns. The values range between 0 and
10 x
1 x
190. The physical position of margin depends on the current character spacing.
To set the values combine the numbers considering that the first line
corresponds to the hundreds, the second line to the tens and the third line to the
units. See the example below:
Example:
How to set the Right Margin to 101.
RIGHT MARGIN
0
1
2
3
4
5
6
7
8
9
(
100 x
10 x
1 x
( )
(
(
(
( ) ( ) ( ) ( )
( ) ( ) ( ) ( ) ( )
( ) ( ) ( ) ( ) ( )
(
( )
( ) ( ) ( )
(
Setup Parameter
Values Description
TOP MARGIN
10 x
1 x
Sets the top margin in number of lines. The values range between 0 and 90. To
set the values combine the numbers considering that the first line corresponds
to the tens, the second line to the units. See the example below.
Example:
How to set the Top Margin to 15.
TOP MARGIN
0
1
2
3
4
5
6
7
8
9
41
Download from Www.Somanuals.com. All Manuals Search And Download.
(
10 x
1 x
( )
(
( ) ( ) ( )
( ) ( ) ( ) ( ) ( )
(
( ) ( ) ( ) ( ) ( )
( ) ( ) ( ) ( )
(
Setup Parameter
Values Description
BOTTOM MARGIN 10 x
1 x
Sets the bottom margin in number of lines. The values range between 0 and
90. To set the values combine the numbers considering that the first line
corresponds to the tens, the second line to the units. See the example below.
Example:
How to set the bottom margin to 34 lines:
BOTTOM MARGIN
0
1
2
3
4
5
6
7
8
9
(
10 x
1 x
( ) ( ) ( )
( )
( ) ( ) ( ) ( ) ( )
(
(
( ) ( ) ( ) ( )
( ) ( ) ( ) ( ) ( )
(
Setup Parameter
Values
Description
IBM COMPRESS 17.1 cpi, 20 cpi
Selects the pitch for the compressed mode printing in IBM
emulation.
IBM C-SET
IBM set 1, IBM set 2
Italic, graphic
Selects the IBM character set.
EPSON C-SET
NATION C-SET
Selects italic or graphic Epson character set.
Selects the national character sets.
USA, FRANCE,
GERMANY, ENGLAND,
DENMARK1, SWEDEN,
ITALY, SPAIN1,
JAPAN, NORWAY,
DENMARK2, SPAIN2,
42
Download from Www.Somanuals.com. All Manuals Search And Download.
LATIN A1
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Parameter
Values
Description
CP437, CP437G,
96GREEK, CP850,
CODE PAGE
Selects the code page for both the IBM and the EPSON
emulations.
CP851, CP852, CP853,
CP855, CP857, CP858,
CP860, CP862, CP863,
CP864, CP865, CP866,
CP867, CP876, CP877,
GOST, TASS, 8859/1,
8859/2, 8859/3, 8859/4,
8859/5, 8859/6, 8859/7,
8859/8, 8859/9, 8859/15
LINE MODE
LF=LF, CR=CR
If the printer receives a LF code (LF), it only performs a line
feed. If the printer receives a CR code (CR), it only performs a
carriage return.
CR=LF+CR
LF=LF+CR
If the printer receives a CR code (CR), it performs a carriage
return followed by a line feed. If the printer receives a LF code
(LF), it performs a line feed.
If the printer receives a LF code (LF), it performs a line feed
followed by a carriage return. If the printer receives a CR code
(CR), it only performs a carriage return.
LF&CR=LF+CR
If the printer receives a LF code (LF) or a CR code (CR), it
performs both a line feed and a carriage return.
WRAP MODE
truncate, autowrap
The data exceeding the line length are truncated ( )
truncate
or printed on the following line (
autowrap
).
SLASHED ZERO no, yes
Selects the printing character for zero, with a slash (yes) or
44
Download from Www.Somanuals.com. All Manuals Search And Download.
without (no).
Setup Parameter
Values
Description
Selects the printing direction of the print head: unidirectional
PRINT DIRECTION unidir., bidir.,
sw control
(
.), bidirectional (
.) or selected via software (
unidir bidir sw
).
control
EJECT ON FF
no, yes
Performs a form feed according to the selected page format ( ) or
no
ejects a cut sheet loaded into the printer (
yes
).
CUT SHEET EJECT on front, on rear Selects whether the cut sheet loaded into the printer is ejected
towards the front or the rear of the printer. The selection of the paper
ejection towards the rear of the printer should be selected only for
paper with a length of at least 14 cm (5,5 inch).
PARK MODE
immediate
When pressing the PARK key or receiving a park command, the
printer immediately parks the paper.
manual imm.
When pressing the PARK key, the printer automatically parks the
paper. When receiving a park command via software:
1. If the current page is not empty (there is printing data or paper
movement commands have been issued), a form feed is
performed.
2. The paper is moved to the tear-off position.
3. The P1, P2, P3 and P4 leds blink.
When the ON LINE key is pressed the printer parks the paper.
after tear
When pressing the PARK key or receiving a park command via
software:
1. If the current page is not empty (there is printable data or paper
movement commands have been issued), a form feed is
45
Download from Www.Somanuals.com. All Manuals Search And Download.
performed.
2. The paper is moved to the tear-off position.
3. The P1, P2, P3 and P4 leds blink.
4. When the ON LINE key is pressed the printer parks the paper
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Parameter
Values
Description
TEAR MODE
auto 1s, auto 2s,
auto 3s, auto 4s,
auto 5s, manual,
no tear/reverse
Selects the way the tear mode is performed. Selecting
auto 1s,
or
, the printer
auto 5s
auto 2s, auto 3s, auto 4s,
moves the paper in the tear-off position and back to the printing
position after the corresponding number of seconds. Selecting
manual, the tear-off is performed manually, by pressing the ON
LINE key. Selecting
, the printer does not
no tear/ reverse
perform the tear-off function (this is useful, when printing on labels).
MANUAL LOADING enabled, disabled Selects the manual loading mode. Setting it to the printer
enabled
loads any kind of document according to the described
procedures. Select , when a more precise paper
disabled
alignment is necessary. With this selection it is not possible to load
documents with a width of less than 90 mm.
ALIGN MODE
GAP MODE
fast, normal
auto, fix
Selects the paper alignment mode. Selecting fastthe printer
performs less checks on the alignment, whereas, if you need a
particularly precise alignment of the documents, select
.
normal
Selects, whether the print gap is sensed for each inserted sheet
(
) or only for the first sheet after the printer power on ( ).
auto
fix
The print gap is sensed separately for the cut sheet and the fanfold
paper.
AUTO
EMPHASIZED
no autoEM, 0.25
mm, 0.35 mm,
Selects the emphasized print mode when the loaded paper is
thicker than the selected value.
0.45 mm, 0.55 mm
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Offset Adjustments
For a precise adjustment of the position of the printed characters on a pre-printed form, this
printer allows to easy adjust of the first line and the first printing column as follows:
1. Press the PROGRAM key while powering the printer on.
2. Insert a blank sheet into the printer.
The following sheet will be printed:
48
Download from Www.Somanuals.com. All Manuals Search And Download.
OFFSET TUNING SETUP
Vertical Position Offset (1/10 INCH)
PROGRAM 1
PROGRAM 2
PROGRAM 3
PROGRAM 4
( )* ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )
( )* ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )
( )* ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )
( )* ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )
0
+1
+2
+3
+4
+5
+6
+7
+8
+9
Vertical Offset Tuning (1/60 INCH)
X
X
X
X
X
X
X
X
X
X
X
X
X
PROGRAM 1
PROGRAM 2
PROGRAM 3
PROGRAM 4
( ) ( ) ( ) ( ) ( ) ( ) ( )* ( ) ( ) ( ) ( ) ( ) ( )
( ) ( ) ( ) ( ) ( ) ( ) ( )* ( ) ( ) ( ) ( ) ( ) ( )
( ) ( ) ( ) ( ) ( ) ( ) ( )* ( ) ( ) ( ) ( ) ( ) ( )
( ) ( ) ( ) ( ) ( ) ( ) ( )* ( ) ( ) ( ) ( ) ( ) ( )
-6
-5
-4
-3
-2
-1
0
+1
+2
+3
+4
+5
+6
Horizontal Position Offset (1/10 INCH)
PROGRAM 1
PROGRAM 2
PROGRAM 3
PROGRAM 4
( ) ( ) ( ) ( ) ( ) ( ) ( )* ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )
( ) ( ) ( ) ( ) ( ) ( ) ( )* ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )
( ) ( ) ( ) ( ) ( ) ( ) ( )* ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )
( ) ( ) ( ) ( ) ( ) ( ) ( )* ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )
-6
Horizontal Offset Tuning (1/60 INCH)
PROGRAM 1 PROGRAM 2 PROGRAM 3 PROGRAM 4
-5
-4
-3
-2
-1
0
+1
+2
+3
+4
+5
+6
+7
+8
+9
X
X
X
X
( )
( )
( )
( )
( )
( )
( ) *
( )
( )
( )
( )
( )
( )
( )
( )
( )
( ) *
( )
( )
( )
( )
( )
( )
( )
( )
( )
( ) *
( )
( )
( )
( )
( )
( )
( )
( )
( )
( ) *
( )
( )
( )
-6
-5
-4
-3
-2
-1
0
+1
+2
+3
X
X
X
X
X
X
49
Download from Www.Somanuals.com. All Manuals Search And Download.
X
X
X
( )
( )
( )
( )
( )
( )
( )
( )
( )
( )
( )
( )
+4
+5
+6
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Vertical Offset Tuning
The
values correspond to 1/60 inches and set the vertical offset of
the first print line starting from the default standard position at 1 mm from the upper paper
margin.
The Horizontal Offset Tuning values correspond to 1/60 inches and set the horizontal
offset of the first print line starting from the default standard position at 3 mm from the left paper
margin.
If you need to change the default position of the first print line the vertical offset can be set in the
Vertical Position Offset lines and/or the horizontal offset in the Vertical Position
Offset
lines. Both these values correspond to 1/10 inch values.
1 mm
X
X
Vertical Offset Tuning
Vertical Offset Tuning
X
X
X
VERT. DEF. POS
3 mm
X
X
X
X
X
HORIZ
DEF.
POS
= FIRST PRINT POSITION
X
X
X
X
X
X
X
X
X
X
Horizontal Offset Tuning
3. Fill in the marker corresponding to the value you want to set and reinsert the sheet into the
printer. The printer reads the selected values and sets them.
4. Turn the printer off.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Clearing Paper Jams
The straight paper path of this printer is designed for trouble-free handling of a great variety of
documents.
In case a paper jam condition occurs, proceed as follows:
1. Open the printer cover.
2. Pull the lever on the right inner side of the printer towards the printer front side to open the
paper path and with the other hand hold the paper path cover.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Remove the jammed paper.
4. If it is not possible to remove the jammed
paper because you cannot reach it with your
hand, or it is embedded so that you cannot
move it, rotate the white cog-wheel beside the
paper path lever to free the paper.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
5. To close the paper path, push the paper path cover down until it locks in position.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Print Quality Problems
The following table is useful for identifying and solve print quality problems.
P r ob lem
Ca u se
Solu t ion
Fading print
The ribbon is not fed
Check that the ribbon is correctly inserted. See
“Installing the Ribbon Cartridge ”.
Turn the ribbon tension knob to verify that the ribbon
is not blocked.
If the problem is not solved, change the ribbon
cartridge.
The ribbon is used up or Change the ribbon cartridge.
torn
Paper
The paper does not
Verify that the paper corresponds to the specifications
damaged after correspond to the
and has been loaded according to the indications
given.
printing
specifications given in
this manual or was not
loaded according to the
indications given
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Hexadecimal Dump
If you need to check the data transmission and want to print in hexadecimal mode, proceed as
follows:
1. Press the LOAD/PARK key until all leds briefly light up while powering the printer on.
2. The data sent to the printer are printed in three columns where the first column indicates the
number of the line, the second shows the hexadecimal values corresponding to the transferred
data and the third column shows the corresponding ASCII values.
3. To exit from the hexadecimal mode turn off the printer.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper Specifications
The documents must all conform to the following characteristics:
· Use paper matching the indicated characteristics.
· They must have well defined top and left edges, with a square angle tolerance of 0.1° on all
edges.
· The paper must not have holes, perforations, folds or tears anywhere within the print area of the
document.
· The radius on a corner of the form must be within 9.5 mm from the left or right edge.
· The form to be printed must not contain foreign material.
· Form opacity must be at least 75%. Forms with a lower opacity may cause feed errors.
· Never print on documents with metallic or hard plastic fasteners or staples, they may damage
the printer.
· To get the maximum print contrast you should print on white or light colored paper. You may
overstrike to improve the low contrasting paper.
· It is preferable to use single and multiple documents with the fibre running in the insertion
direction of the printing unit.
· Recycled paper is permitted on principle.
· It is preferable to print on multiple forms with a narrow glue strip or top-gluing. The gluing
must not cause waving in the set of forms.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Cuts Sheets
Insertion direction
D
C
C
Paper weight
Paper thickness min. 0.06 mm max. 0.6 mm
min. 60 g/m2
B
Print Area
Copies
Original + 8 copies
E
A
Dimensions
Form width
Maximum
240 mm
(226 mm if
Minimum
70 mm (manual alignment)
90 mm (automatic alignment)
A
thickness is
higher than 0.2
mm
B
C
Form length
Distance between dot position
and left or right paper edge
711.2 mm
-
68.6 mm
3.0 mm if length is less than 355.6 mm
8.0 mm if length is between 335.6 and 711.2
mm
D
Distance between top of the
first printed line and top
margin of the document
-
1 mm
58
Download from Www.Somanuals.com. All Manuals Search And Download.
E
Distance between the lower
margin and the lower part of
the last printed line
-
6.6 mm
Fanfold Paper
A
Dimensions
Maximum Minimum
A
B
C
Page width
Page length
235 mm
79 mm
68.6 mm
3.0 mm
D
-
-
Distance between
the left or right
vertical paper
perforation and the
leftmost or rightmost
printing dot.
Print Area
B
D
E
Distance between
the upper page
margin and the
upper margin of the
first print line
Distance between
the lower page
margin and the lower
margin of the last
print line.
-
-
1 mm
C
E
6.6 mm
0.06 mm
Paper thickness
Copies
0.6 mm
1 original +
8 copies
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Printing Technology
Print head:
Resolution:
24 pin
360x360 dpi (HxV)
Line Length (@ 10 cpi)
94 columns (cut sheets)
80 columns (fanfold)
Printing Speed
420/350 cps @ 12/10 cpi (Draft)
140/117 cps @ 12/10 cpi (LQ)
Emulation
IBM ® Personal Printer 2390+, Proprinter XL24E, Proprinter XL24AGM, Epson 570
Resident Fonts
Draft, Courier, Gothic, Prestige, Presentor, Script, OCR-A, OCR-B, Boldface
Character Set
PC standard set (CS1-CS2) - 13 National Epson sets - CP437 (USA) - CP437G (Greek) -
CP850(Multilanguage) – CP851 (Greek) - CP852 (Latin 2) - CP853 (Turkish) - CP855 (Russian) -
CP857 (Turkish) - CP860 (Portuguese) - CP862 (Hebrew) - CP863 (French/Canadian) - CP864
(Arabic) - CP865 (Norwegian) – CP866 (Cyrillic) - CP867 (Turkish) - CP876 (OCRA) - CP877 (OCRB) -
CP 858 (Euro) - Gost – Tass – ISO 8859/1/2/3/4/5/6/7/8/9/15 - 96 GREEK
Barcodes
UPC/A, UPC/E, EAN8, EAN13, Code 39, Code 128, Postnet, Codabar, ADD-ON 2, ADD-ON 5, Code
60
Download from Www.Somanuals.com. All Manuals Search And Download.
11, Code 93, BCD, MSI, 2/5 Interleaved, 2/5 Matrix, 2/5 Industrial
Interfaces
Parallel IEEE 1284 bidirectional,
Serial RS-232/C
Automatic Interface Switching
Memory
32 Kbytes buffer
Special Functions
Automatic Gap Adjustment (AGA)
Auto Alignment
Auto Border Recognition
Bar Code Reading (in horizontal & vertical mode - option)
Ribbon Life
4 million characters (black)
Reliability
MTBF: 10.000 hours
Print Head Life
400 million characters
Physical Dimensions & Weight
390 (W) x 210 (H) x 320 (D) mm
14 Kg
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Supply
Tension:
110V and 220V
Frequency :
60 Hz and 50 Hz
Power consumption:
120 W max. (printing), 10 W (standby)
Environmental conditions
Temperature:
Humidity:
working 5/40 °C, stock -25/60 °C
working from 20 to 85% (r.h.),
stock from 10% to 90% (r.h.) (without condensing)
Standard
EN 60950, IEC 950
Environment
Energy star compliant
Noise Level
55dbA
62
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Notes
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a pa rticular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the followin g measures:
·
·
·
·
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an exper ienced radio/TV technician for help.
A shielded Centronics IEEE1284 compliant bi-directional parallel cable, maximum length 3 meters (10 feet), and a
shielded RS-232 serial cable, maximum length 15 meters (50 feet), are necessary for this device to meet the
requirements of a Class B digital device pursuant to part 15 of the FCC rules.
The above specified cables are readily available as Personal Computer or Peripheral accessories from multiple retail
outlets. Please consult your dealer for details concerning such cables and also for information about FCC rules for
digital devices.
Changes or modifications to the device covered by this manual, which are not expressly approved by the party
responsible for compliance, could void the user’s authority under the FCC rules to operate the equipment.
Canadian D.O.C. Radio Interference Regulation
This digital apparatus complies with the Canadian ICES -003 Class B limits for radio frequency emissions.
Cet appareil numérique est conforme aux limites de Classe B de la nor me NMB-003 du Canada.
EEC Regulations
This equipment conforms to the EEC Directive 89/392 (the sound pressure, measured according to ISO 7779, does not
exceed 70 dBA).
63
Download from Www.Somanuals.com. All Manuals Search And Download.
|