Assembly Instructions
LP Gas & Charcoal Grill
Model # CG3023E
Please keep this instruction manual for future reference
Customer Service: (888) 922-2336, 8:00am to 5:00pm, Central Standard Time,
Monday thru Friday
(Made in China)
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
Safety Precautions
Always read and follow all DANGER, WARNING, AND FOR YOUR SAFETY notices in this Grill
Guide. Failure to follow these notices may result in property damage, bodily injury, or death.
1. Grill installation must conform with local codes, or in their absence, with either the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1, or
Propane Storage and Handling Code, B149.2.
2. This gas grill, when installed, must be electrically grounded in accordance with local codes, or, in
the absence of local codes, with the National Electrical Code, ANSI Z21.58-2007, or the Canadian
Electrical Code, CSA 1.6-2007.
3. This gas grill is intended for outdoor use only, and should not be used in a building, garage, or any
other enclosed area.
4. This gas grill is not intended to be installed in or on recreational vehicles and/or boats.
5. Never use any other type of fuel for this grill other than LP gas (propane).
6. Only use the pressure regulator with a type 1 connector that is supplied with this gas grill
7. Before each use, check the gas hose for excessive abrasion, cracking, fraying, wear, or cuts.
Replace a hose assembly showing those signs with the hose assembly specified in the parts list
before using the grill.
8. Always perform a Leak Test before operating your grill.
WARNING
1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
2. An LP cylinder not connected for use should not be stored in the vicinity of this or any other
appliance.
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from appliance and call your local fire department.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
• Tools and Parts
• Hardware
• Assembly Instructions
• Care and Maintenance
• Warranty Information
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Tools Required
1
Descr iption
Adjust able wrench
(not provi ded)
2
Descr iption
Scr ewdrive r
(not provi ded)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 1:
Assemble the two middle panels (16, 18)
and four side panels (11,15, 27, 29).
Make sure to assemble the two middle
panels (16, 18) first.
Assemble two middle panels using
8-M6x12 Bolts (B), and assemble side
panels using 11-M6x12 Bolts(B) and
11-FLANGE LOCK NUTS (H).
See the illustration below.
Step 2:
Assemble the ash pan (28) use
BOLT M6x12 (B) fasten the ash pan and
right middle panel. Then assemble the plug
(51). See the illustration below.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 3:
Attach the ash pan to the front and back
panels using 4-BOLT M6x12 (B) and
4-M6 FLANGE LOCK NUTS (H).
See the illustration below.
Step 4:
Turn over the grill body and assemble
the left leg (38) and right leg (42) onto
the body using 8-BOLT M6x12 (B) and
6-M6 FLANGE LOCK BUTS (H).
Please do not tighten the screws
at this time.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 5:
Use BOLT M6x50 (F) to attach the
bottom shelf (44) to legs, attach the
highlighted in red legs first.
Assemble the cylinder hanger (35) to the
top of left leg (38) using 2-BOLT
M6x12 (B), as shown in the picture
below. Using 2-BOLT M6x50 (F) and
2-FLANGE LOCK NUTS (H) to
assemble the gas tank holder (39)
to the grill left leg (38) as shown below.
DO NOT INSTALL THE
CYLINDER AT THIS
TIME
Step 6:
Place the axle (41) through the left leg
(38) of the grill. Place the wheels (40)
on the axle on the outside of the legs,
attach the wheels with 2-washers (L)
and 2-pins (I) on the outside of the
wheels. Place the pins (I) through the
hole in the axle outside of the washers.
See illustration below.
Attach the 2 Directional casters (45) to
the bottom of the right leg (42).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 7:
Attach the two triangular support braces
(17, 26) connecting the legs to the back
panel of the body using 8-BOLTS
M6x12 (B).
Step 8:
Attach short fence rail 2pcs and long fence
rail 2pcs to the four legs, using 8-BOLTS
M6x12 (B) to fix.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 9:
Assemble the accessories shelf (36) to
the charcoal section of the grill using
4-BOLTS M6x12 (B).
Step 10:
Attach the control panel (32) using
4-BOLT M6x12 (B), attach the knobs (33)
as shown below. Attach the firebox
bracket (30) to the right legs (42) using
2-BOLTS M6x60 (G) and 2-FLANGE
LOCK NUTS (H).
Tighten all connections at this time.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 11:
Attach the knob (33) and 4-BOLTS
M6x12 (B) onto the body of side burner
(12).
Step 12:
Attach the side burner onto the body of
the grill as shown below.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 13:
Take the Heat Shield (53) upon the
Firebox Lid (22). Then attach the
Handle(Firebox) (24),using Firebox Lid
Handle Base(small)-2pcs(54) and
2-BOLT M6X25(C) . Then attach the
Firebox Lid(22) upon the body of
firebox(23),using Hinges(Body)(13)
and 4-BOLT M6X35(D)and4-NUT M6
FLANGE LOCK(H) ,as shown below.
Step 14:
Attach the side door handle (46) and air
vent (48) onto the body of firebox using
2-BOLTS M6x12 (B) and 2-FLANGE
LOCK NUTS (H).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 15:
Attach the hinges bottom (14) onto the
back of the grill (total four pcs) using
4-BOLTS M6x40 (D). Attach the
Firebox Handle(24) onto the firebox
using Firebox lid handle base (54) and
Bolt M6X25(C).
See the illustration below.
Step 16:
Attach 2-BOLTS M6x12 (B) into the body
of firebox.
NOTE: PLEASE DO NOT TIGHTEN THE
BOLT NOW, AS SHOWN BELOW.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 17:
Attach the firebox to the main body of
the grill, in the same manner that the
side burner was attached in step 12.
Using 4 additional BOLTS M6x12 (B),
connect the firebox to the grill body from
the inside of the grill body. Then use
2-NUT M6 FLANGE LOCK(H) to fixed.
Once all bolts are in place and assembly
of the firebox is complete, tighten all of
the nuts and bolts.
Step 18:
Place the cooking grid (25) and
charcoal pan (47) into the body of
the firebox.
As shown below.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 19:
Using “R”PIN(I) and PIN Roll(K) to
fixed the Hinges body(13) and
bottom(14).
As showen below.
Step 20:
Attach 4-Hinges bottom to the grill body,
using 8-BOLT M6X40(E) to fix.
Then attach Extension Wire to the left
side of grill body,using 1-BOLT M6X12(B)
and 1-NUT M6 FLANGEL LOCK to fixed.
As showen below.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 21:
Attach Hinges bottom(14) to the Lid
Gas(5),using4- BOLT M6X40(E) and
4-NUT M6 FLANGEL LOCK(H) to fixed.
Then attach 2-stack gas(3) to the lid
gas(5),using 4-BOLT M6X20(B) and
4-NUT M6 FLANGEL LOCK(H) to
fixed .Then attach the thermometer(4)
to the lid gas(5).Last attach the
lid handle (1) and lid handle base (2)
to lid gas(5) ,using 2- BOLT M6X25(C)
to fixed.
Step 22:
Attach handle (1) and lid handle base (2)
to lid gas(5) ,using 2- BOLT M6X25(C)
to fixed.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 23:
Put the lid gas(5) and lid charcoal(6)
upon the grill body . Using “R”PIN(I)
and PIN Roll(K) to fixed the Hinges
body(13) and bottom(14).
Step 24:
Put the 3-burner(10) into the left side of
grill body,then use BOLT M4X8 (A) to
fixed.
As showen below.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 25:
Put 3-Flame tamer into the left side of
grill body.
Attach the lifting handle(21) to the
charcoal pan(20), then put them into
the left side of grill body.
Step 26:
Attach the 2-warming rack(19) to the
lid and grill body.
Then attach “R”PIN(J) to left side of
lid gas(5).
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 27:
Put 6-cooking grid(8) into the grill body.
As showen below.
Step 28:
Put receiving tray(37) under grease
tray(34), then put them under the
bottom of grill body.
As showen below.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Step 29:
Attach the Regulator(31).Then put Grate hook
(49) on the hook(50).
Assemble the regulator by
an adjustable Wrench
Final Assembly
23
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS GRILL
Your new Outdoor Gourmet™ Grill has been designed and manufactured to high quality standards. It will
provide you with many years of enjoyment with a minimal amount of maintenance. Please keep in mind the
following FOR YOUR SAFETY.
OPERATION
1. Your gas grill requires reasonable care during operation. It will be hot during cooking and cleaning.
You should never leave the grill unattended or move the grill when in use.
2. Children should never use your gas grill. Keep younger children and pets away when in use.
3. Only use your gas grill outside in a well-ventilated area. Never use indoors in any building, garage,
shed, or under any type of flammable canopy or overhang.
4. Ensure your grill is on level ground and the locking casters are locked before use.
5. Turn all gas valves off should the burners go out when cooking. Open the lid and wait 5 minutes before
relighting.
6. Do not lean over the grill or touch the edges of the firebox or lid when in use.
7. Turn the burners off, close the lid, and shut off the LP cylinder should a grease fire occur.
8. Do not obstruct the flow of combustion and ventilation air to this grill.
9. Keep the outdoor cooking gas appliance area clear and free from combustible materials, gasoline, and
other flammable vapors and liquids.
10. Keep the ventilation openings of the cylinder enclosure free and clear from debris.
11. Do not put a barbecue cover or other flammable material in the storage area of this grill.
12. Do not use charcoal briquettes, lava rock, or any type of ceramic product in the gas section of this grill.
13. Do not install or use on or in a recreational vehicle and/or boats.
LP Gas and Cylinder Information
Your new gas grill operates on LP (Liquid Petroleum) Gas. It is odorless, colorless, and non-toxic when
produced. You can smell LP gas as it has been given an odor similar to rotten cabbage for your safety.
Triangular Hand Wheel
Your grill uses the newest and safest LP Gas Cylinder.
1. O.P.D. (Overfill Protection Device) – prevents accidental gas leaks
caused by overfilling of the tank. Each tank contains a float that
closes the input valve when the tank is 80% full. This allows room
for the LP gas to expand in hot temperatures. A triangular hand wheel
distinguishes this type of tank.
2. O.C.C.1 Type 1 Quick Connect Valve – provides fast tank hook-ups and requires only to be tightened by
hand.
In addition, the LP tank you use with your grill must meet the following requirements
1. Required Measurements: 12-1/2” (317mm) in diameter and 18-1/2” (472mm) in height.
2. 20-pound (9.1kg) propane cylinder.
3. Constructed and marked with U.S. Department of Transportation (D.O.T.) for the US or CAN/CSA-
B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission, for
Canada.
4. A safety release valve.
5. A means for vapor withdrawal.
WARNING
1. Do not attempt to use a cylinder with any other type of connection device.
2. Do not attempt to use a cylinder with a larger capacity
24
Download from Www.Somanuals.com. All Manuals Search And Download.
LP CYLINDER FILLING AND EXCHANGE
Some areas only allow you to exchange your empty cylinder for a replacement that is already full. Other areas
allow you to refill your cylinder. If you are in an area where you can refill your cylinder:
1. Use only a licensed dealer.
2. The dealer must first purge the cylinder before filling.
3. Never fill a cylinder more than 80% full by volume. Volume will vary by temperature. An empty
cylinder weighs approximately 18 pounds (8.2kgs). A full one approximately 38 pounds (17.3kgs).
4. Be sure the LP dealer checks the cylinder for leaks after filling.
5. Do not release LP gas into the atmosphere, as it can unexpectedly ignite when mixed with air.
6. Contact a LP dealer to remove LP gas from a cylinder.
7. Only exchange your cylinder for one with an O.P.D. feature as shown on previous page.
WARNING
A frosty cylinder valve indicates possible gas overfill. Close the LP valve and call your dealer
immediately.
WARNING
1. Never store any extra cylinders near your grill.
2. Keep cylinders out of direct sunlight and high heat.
3. Never fill your cylinder over 80% full by volume. This may cause release of gas from the safety
release valve.
4. Immediately call your LP dealer or fire department should you hear, smell, or see escaping gas
from the cylinder.
5. Do not insert any type of foreign objects into the valve outlet.
WARNING
1. The gas supply must be turned off at the LP-gas supply cylinder when this outdoor cooking gas
appliance is not in use.
2. Storage of this gas grill indoors is permissible only if the cylinder is disconnected and removed from
the gas grill.
3. Cylinders must be stored outdoors out of reach of children and must not be stored in a building,
garage, or any other enclosed area.
LP CYLINDER LEAK TEST
A leak test should be done each time a cylinder is refilled or exchanged. Do
not smoke or use any type of flammable material in the area during this leak test.
Do not use an open flame to check for leaks.
1. Test outside in a well ventilated area.
2. Use a paintbrush and a solution of 50% liquid soap and 50% water. Do
not use cleaning agents and they can damage the fuel supply parts.
3. Brush liquid onto areas highlighted with arrows.
4. Growing bubbles indicate a leak.
DANGER
Growing bubbles indicate a leak. In that case, call your LP dealer or fire department immediately.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSPORTATION AND STORAGE
1. Always use the Safety Cap when transporting or storing your cylinder.
2. Do not store in a building, garage, or other enclosed area.
3. Always store your cylinder outside.
4. Store out of reach of children.
5. Always transport in an upright position.
Dust Cap
6. Do not smoke when transporting your cylinder.
Regulator and LP Cylinder Connections
CAUTION
The gas pressure regulator provided with this outdoor cooking appliance must be used. This regulator is set
for an outlet pressure of 11 inches water column.
Your regulator is equipped with a Q.C.C. Type 1 quick connect system. It will not allow gas to flow until a
positive seal has been made. It has a thermal element that will shut off the gas flow if the temperature reaches
240 degrees F (115 degrees C). It also has a flow-limiting device that will restrict the flow of gas to 10 cubic
feet per hour (0.28 cubic meters per hour).
Before each use, check the gas hose for excessive abrasion or wear, or cuts. Replace a hose assembly showing
those signs with the hose assembly specified in the parts list before using the grill.
Gas Valve Manifold
Assembly
TO CONNECT THE CYLINDER TO THE REGULATOR AND HOSE
1. Be sure the LP cylinder is “OFF” by turning the hand wheel clockwise
until it stops.
2. Place the cylinder on the hook beside of body
with the valve
facing outward. See Assembly Instructions to secure.
3. Be sure all burner controls are turned to the “Off” position.
4. Remove the safety cap from the from the cylinder valve.
5. Center the nipple of the regulator into the cylinder valve
6. Turn the black nut clockwise until it stops. Hand Tighten Only.
Do Not Use A Wrench.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
The regulator must enter the
cylinder valve in a straight
line.
Center this nipple of the
regulator into the cylinder
valve.
Q.C.C.1 Type 1 Connector
WARNING
Always keep the gas cylinder in
the upright position at all times
WARNING
1. Do not connect this grill to any unregulated sources of propane.
2. Before each use, check the gas hose for excessive abrasion or wear, or cuts. Replace a hose
assembly showing those signs with the hose assembly specified in the parts list before using the
grill. Inspect the hose assembly by opening the cabinet door underneath the side burner and
following the regulator hose up to its connection to the gas manifold assembly.
3. Always perform the Leak Test listed below before using your grill for the first time, if the cylinder
has been changed, any gas components have been changed, the regulator flow-limiting device has
been activated, or after a long period of non-use.
4. Do not attempt to connect this grill to the LP system of a motor home or trailer.
LEAK TESTING THE REGULATOR, VALVES, HOSES, AND CONNECTIONS
1. Ensure the LP cylinder valve and all burners are “Off”.
2. Ensure the LP cylinder is connected to the regulator.
3. If the information in1 & 2 is not followed exactly, a fire causing death or serious injury may occur.
4. Mix up a solution of 50% water and 50% liquid dish soap. Do not use any household cleaner
solution.
5. Open the LP tank valve by turning the hand wheel counterclockwise one turn. If you hear a rushing
sound, turn the gas off immediately. In that case, there could be a leak at the connection. Reconnect
the cylinder to the regulator.
6. Spray or brush on the solution covering the following areas: cylinder welds, regulator and cylinder
connection, gas hose connections to the regulator, all gas hoses, all gas hose connections to the
burners including the main and side burners.
7. Growing bubbles on any of the parts and connections listed above indicate a gas leak. Immediately
shut off the LP tank valve by turning the valve clockwise. Retighten the connections or order
replacement parts as needed. Continue to test as necessary until no leaks are detected.
8. Close the LP tank valve by turning the hand wheel clockwise.
WARNING
1. DO NOT USE THE GRILL if you cannot stop the leaks. Be sure the LP cylinder valve is closed.
If the LP cylinder is still leaking, contact your LP dealer or local fire department.
2. Do not use any match or open flame, or smoke, during leak testing.
3. Do not light a burner during leaktesting.
4. The replacement hose assembly must be the one identified.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR SAFETY
1. Minimum clearance from sides and back of unit to adjacent combustible construction below top
of unit, 24 inches (60 cm) from sides and 24 inches (60 cm) from back.
2. Do not locate this outdoor cooking gas appliance under overhead-unprotected combustible
surfaces.
APARTMENT RESIDENTS
Check with your apartment manager regarding
your regulations for barbecues.
WARNING
1. Do not use this grill in any enclosed
area, garage, shed, or under any type of
overhead structure or canopy.
2. Operate this grill only in a well-
ventilated area.
Keep any electrical supply cord and the fuel
supply hose away from any heated surfaces and
water.
Do not face the grill directly into the wind.
Grill Operations
LIGHTING
Always visually inspect your grill before lighting. Replace any hoses that are frayed or cracked before lighting
your grill. Look for anything that may be blocking spaces for ventilation and remove. After lighting, always
check the flame to ensure you have a good flame all along each burner. If not able to light, or the flame is not
even along the entire burner(s), then see the Trouble Shooting section
WARNING
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 5 seconds, turn the burner control(s) off, wait 5 minutes and repeat the
lighting procedure
28
Download from Www.Somanuals.com. All Manuals Search And Download.
LIGHTING THE MAIN BURNERS USING ELECTRONIC IGNITION
1. Open the lid.
Main Burner
2. Ensure all burner control knobs are in the “Off” position.
3. Turn on the LP gas by turning the hand wheel on the cylinder valve.
4. Turn one burner control knob marked with an igniter flame “ ” to “High”.
5. Depress the electronic ignition button and hold down. You should hear a
clicking sound, which shows the electronic ignition is working.
Electric Ig
i
ter
6. If the burner does not light within 5 seconds, turn the burner control knob to “Off”. Wait 5 minutes for the
gas to clear, and repeat the above procedure. Use the Manual directions if it still will not light.
7. When lit, turn the control knob to the desired setting.
8. Your grill is equipped with continuous ignition. Simply turn the control knob of the burner next to the lit
burner to HI. It will light automatically. Do not press the electronic ignition button again. Then adjust
control knob(s) to desired settings.
MANUALLY LIGHTING THE MAIN BURNERS WITH THE MATCH LIGHTING STICK
1. Open the lid.
2. Ensure all burners are in the “Off” position.
3. Slowly turn on the gas at the LP tank valve if it is not already on.
4. Place a match in the Match Holder. This is located in the top center
drawer of the grill cabinet underneath the right main burner.
5. Use the holder to slide the lit match though the cooking grates and the
front of the heat tent to the left of the burner you wish to light.
6. Press and turn the burner control knob to “HI/LIGHT”. Continue to push
in and hold up to 5 seconds or until the burner lights.
7. If the burner does not light within 5 seconds, turn the burner control
knob to “Off”. Wait 5 minutes for gas to clear, and try again.
8. When lit, turn the control knob to the desired heat setting.
LIGHTING THE SIDE BURNER WITH ELECTRONIC IGNITION
1. Open the side burner cover
2. Ensure the side burner control knob is in the “Off” position, as well as any main burners not in use.
3. Turn on the LP gas if it is not already on.
4. Turn the side burner control knob to “High”.
5. Depress the electronic ignition button and hold. You should hear a clicking sound, which shows the
electronic ignition is working.
6. If the burner does not light within 5 seconds, turn the burner control knob to “Off”. Wait 5 minutes for the
gas to clear, and repeat the above procedure. Use the Manual directions if it still will not light.
7. When lit, turn the side burner control knob to its desired setting.
LIGHTING THE SIDE BURNER WITH THE MATCH LIGHTING STICK
1. Open the lid or side burner cover.
2. Ensure the side control knobs are in the “Off” position as well as any
main burner not in use.
3. Turn on the LP gas if it is not already on.
4. Strike the match, and place near the top of the burner.
5. Turn the side burner control knob to “HIGH”.
6. If the burner does not light within 5 seconds, turn the burner
control knob to “Off”. Wait 5 minutes for the gas to clear, and try again.
7. When lit, turn the burner control knobs to their desired setting.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TURNING OFF YOUR GRILL
1. Turn off the gas supply at the LP tank by turning the valve clockwise.
2. Turn all burner control knobs to the “Off” position.
Cleaning Your Grill
WARNING
1. Do not clean any part of your barbecue grill in a self-cleaning oven.
2. Do not use oven cleaners, abrasive kitchen cleaners, cleaners that contain citrus products, or mineral
spirits.
3. Do not use any type of steel bristled brush.
4. Clean your grill regularly to prohibit grease build-ups and avoid a grease fire or excessive flare-ups.
5. Always allow the grill to cool down prior to cleaning.
STAINLESS STEEL – clean with multipurpose low abrasive non-phosphorous metal or stainless steel polish
and a soft cloth. Always polish in the direction of the lines. Do not allow grease and dirt to accumulate.
In addition, the following products and naturally occurring substances in the outdoors will damage all stainless
steel finishes. Use caution so that they do not come in contact with your Gas Grill. Immediately wash them off
and dry the stainless steel should they ever come in contact with your Gas Grill. This includes, but is not
limited to, Pool Chemicals (chlorine and bromine), Lawn Fertilizer, Ice Melting Salts, Sea or Salt Water, Urine,
Bird Droppings, and Tree Sap.
OTHER EXTERIOR SURFACES– wash with a mild dish soap and warm water. A cloth, soft brush, or
plastic cleaning pad can be used. Rinse thoroughly and wipe dry.
COOKING GRATES, WARMING RACK, AND HEAT DIFFUSERS – use a stiff brass brush. Wash with
warm water and mild dish soap as needed, rinse, and dry.
GREASE PAN AND TRAY – check after each use. Remove and empty the Tray when half full. Remove and
clean the Pan as grease builds up. Both can be washed with warm water and mild dish soap.
ELECTRONIC IGNITER – visually inspect for cracks. Replace if a crack is found. Do not use water to
clean the igniter.
BURNERS – we recommend you clean your burners at least twice a year, or before use if the grill has not been
used in over one month.
WARNING
Small insects, such as spiders, are able to access the burner tubes. Sometimes they will build nests or spin
webs. In either case, this can block or reduce the amount of gas flowing through the burner. You will
usually see a smaller flame, or a flame that is mostly yellow rather than blue, coming from the burner when
this happens. Other signs include the gill not heating evenly, not reaching temperature, or burners not
igniting. In cases with severe blockage, this can cause the flame to burn backwards, and outside of the
burner tubes, which can cause damage to your grill and/or personal injury. IMMEDIATELY SHUT OFF
THE FLOW OF LP GAS AT THE CYLINDER BY TURNING THE HAND WHEEL
CLOCKWISE SHOULD THIS HAPPEN. Wait for the grill to cool, and then clean all burners.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING THE BURNERS
1. Ensure the LP gas is turned off at the LP cylinder.
2. Remove the cooking grates, flame tamer, and grease tray.
3. Remove the cotter pins located underneath the back end of each burner.
4. Lift each burner up and out.
5. Clean the inside of the burner using a stiff wire. A straightened coat
hanger is one suggested tool. An alternative way to clean the inside
of the burner is using compressed air. Always wear eye protection
if using this method. Never enlarge the burner ports during cleaning.
6. Brush the outer surface of the burner.
7. Ensure all ports (holes) are free of all debris
8. Inspect the burner. Replace if any cracks or enlarged holes.
9. Reinstall the burners making sure the burners seat over the
valves as shown in the figure to the right.
WARNING
Properly locating the burner with respect to the orifice is vital for safety.
10. Secure the back of the burners to the firebox with the cotter pins.
11. Replace the grease tray, flame tamer, and cooking grates.
12. Perform a Leak Test described earlier in this guide.
BURNER FLAMES
Always inspect the burner flame after lighting. A good
flame should be primarily blue with a yellow tip and have
a minimal amount of noise. Some yellow tips are OK if
under one inch. New burners sometimes have oil residue,
which will cause yellow flame when burning off. Variations
in gas supply, altitude, weather, and other factors can all
impact burner performance. Older grills can also show
more yellow flame as food deposits, oils, and fats can build up.
ALWAYS
1. Keep the grilling area clear and free from combustible materials, gasoline and other flammable vapors and
liquids.
2. Do not obstruct the flow of combustion and ventilation air.
3. Keep the ventilation openings of the cylinder enclosure free and clear from debris.
ELECTRONIC IGNITION MAINTENANCE
Your grill is equipped with electronic ignition. It’s powered by one “AA” size battery. Replace the battery
when necessary. Unscrew the igniter top. Place the new battery into the igniter with the positive (+) end of the
battery facing up. Screw the igniter top back into place.
GRILL STORAGE
1. Clean your grill before storage.
2. Storage of a gas grill indoors is permissible only if the cylinder is disconnected and removed from the
gas grill.
3. Cover the grill.
4. Perform a Leak Test before use after storage.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Grilling With Your New Grill
Welcome to the world of grilling. Whether you’re already an established griller, or just starting out, your new
grill should bring you much enjoyment and satisfaction, to say nothing of some phenomenal meals. We
encourage you to experiment to find your own favorite recipes.
The control panel is labeled “HI/LIGHT”, “LOW”, and “OFF” for each burner control knob. Simply push in on
the temperature control knobs and turn to the desired heat setting. A thermometer is placed in the hood so that
you can see the cooking temperature inside the grill.
The heat diffusers are designed to help evenly distribute heat throughout the grill. They are also designed to
catch and smoke the right amount of drippings, adding more flavors to your meal.
DIRECT VS. INDIRECT COOKING
Food cooked on the grill is either done using direct or indirect cooking. Direct cooking is when the food is
cooked directly over the heat. Food is placed in-between the burners for indirect cooking.
DIRECT – used for preheating and searing
Use Direct cooking to sear meats. This helps to keep food moist by locking in juices. Some food, such as steak,
is first seared using Direct cooking, and then finished cooking using the Indirect method. This is generally used
for quicker cooking foods. Preheat the grill to 500°F (260°C). You can shut off one or more burners if you do
not need to use the entire grilling surface once you reach over 500°F(260°C). You can also use a medium high
heat of 400°F or more by turning the burners down slightly. Place the food directly over the heat source.
Remain vigilant when grilling using this method, as it’s easy to overcook.
INDIRECT – how most food is cooked on a gas grill
Indirect cooking is used for foods that take longer to cook, including large cuts of meat such as roasts. It’s also
used for cooking more delicate food that can dry out quickly such as fish and poultry, for fattier foods to reduce
flare-ups, and when grilling using a roasting pan or aluminum foil. Preheat the grill to 500°F(260°C). Then
turn some burners off, and others to medium to low depending on the temperature you want to maintain.
Generally, turn the center burner off for a 3-burner model and the 2 inside burners off on a 4-burner model.
Grills with more than 4 burners will vary depending on what you are cooking. Generally, you want to keep the
temperature around 350°F. Do not place the food directly over any burners when using this grilling method. .
SIDE BURNER
Use the side burner to boil soups, corn on the cob, lobster, steam, stir-fries, or warm.
GRILLING TIPS AND TRICKS
1. Always “Preheat” your grill before cooking. Light all main burners, turn to “HI”, and close the lid until the
thermometer reads over 500°F (260°C), which should be 4 minutes. Then adjust the burner control knobs to
the proper temperature. Note that no preheating is necessary for the side burner.
2. The thermometer measures the temperature at the top of the lid. The temperature down by the cooking grates
is generally somewhat warmer.
3. Mother Nature can impact your grilling times. Allow more cooking time for cold, wind, and higher altitudes.
We recommend you place the grill in an area protected from much wind.
4. Trim away any excess fat from meat to reduce flare-ups.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Keep similar size portions together so that they cook more evenly.
6. Generally speaking, the more food on the grill, the longer the cooking time.
7. Be aware when using the Direct cooking method, as food can easily become overcooked, burned, or dry out.
Food may require more turning, or sometimes, may need to be moved off the flame.
8. Larger pieces of meat generally require more cooking time per pound than smaller pieces of meat.
9. If a major flare-up, or too many flare-ups occur, turn off the gas, move the food away from the flare-up, and
close the hood. Restart the grill once the flare-up has died down.
10. Turn foods infrequently. Generally, only turn a steak once during cooking.
11. Use tongs rather than a fork when turning the food on the grill. Less juice will be lost that way.
12. Know your sauce and when to apply. Oil and vinegar based sauces can be brushed on any time. Sugar
based sauces like barbecue sauce should be applied during the last few minutes of cooking.
13. A timer can help you keep from over-cooking the food.
14. Use insulated protective mitts or potholders when working around a grill in operation.
15. Use a small amount of cooking oil on the cooking grates before heating to reduce foods sticking on the
grates.
FOOD SAFETY
1. Always use safe food handling and preparation when using this grill.
2. Wash all poultry, seafood, and vegetables before cooking.
3. Use separate platters, plates, and utensils for uncooked and cooked foods.
4. Leave all meat, poultry, and seafood in the refrigerator until ready to cook.
5. Use a meat thermometer to ensure foods are adequately cooked.
Trouble Shooting Guide
BURNER WILL NOT LIGHT
1.) Gas supply is turned off. Turn on gas at LP tank.
2.) Out of propane. Check to be sure you still have propane in your tank.
3.) Regulator is not properly seated into the tank valve. Remove and reattach. Hand tighten only.
4.) Crimped fuel supply hose. Inspect and straighten.
5.) Regulator failure or damaged hose. Order replacement part and replace.
6.) Make sure you can hear the electronic igniter clicking. If not, replace the battery with an “AA” size.
Inspect the electrode to be sure it’s not coated in grease or dirt. If so, clean with rubbing alcohol. Check
the distance from the electrode tip to the burner. The tip of the electrode should be 1/8” to ¼” from the
main burner and 1/8” to 3/16” from the side burner. Adjust if necessary. Inspect the electrodes to be
sure they are not cracked or broken. If so, order replacement parts and replace.
7.) Blockage in the gas system. Inspect the burners to be sure insects, spider webs, etc do not block them.
Clean if necessary. Inspect under the control panel to be sure the burners are aligned properly with the
valves.
IRREGULAR FLAME OR YELLOW FLAME
1.) New burner may have residual oil, which will burn off.
2.) Tubes in burners are blocked. Remove and clean.
3.) Burners have a high grease or dirt build-up. Remove and clean.
4.) Burners are not aligned properly with the valves. Inspect under the control panel.
SUDDEN DROP IN GAS PRESSURE OR FLAMES BLOW OUT
1.) Out of gas. Check to be sure you still have propane in your tank.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.) Your excessive fuel flow valve has tripped, thereby reducing the flow of gas. Turn off all burners, wait
30 seconds, and relight grill. If problem persists, turn off all burners. Disconnect regulator from tank.
Wait 10 minutes. Reconnect regulator and leak test. Slowly turn on LP tank and relight grill. Other
ways the flow limiting device can be activated include
a. A ruptured gas hose. Inspect, perform a leak test, and replace as necessary.
b. Opening the control knobs before turning on the LP gas at the tank. Turn on the gas at the LP
tank first before turning on a control knob to light.
c. Improper purging of tank before it was filled. See your LP gas dealer.
3.) Wind could be blowing out your burners. Turn front of grill to face wind or move out of the wind.
EXCESSIVE FLARE-UPS
1.) Flame tamer, inside of grill, grates, and burners need to be cleaned.
2.) Grease tray needs to be cleaned and emptied.
3.) Using too high of heat to cook. Reduce control knob setting.
4.) Direct cooking method will produce more flare-ups than indirect. If using direct method, try using
indirect.
FIRE BEHIND CONTROL PANEL
Immediately shut off LP tank valve and allow grill to cool.
1.) Check burners for obstructions and clean.
2.) Inspect under the control panel to be sure the burners are aligned properly with the valves.
3.) Gas is leaking from a faulty connection or damaged hose. Perform a leak test and inspect for leaks.
Tighten or replace parts as necessary.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
CHARCOAL SECTION AND SMOKER
PREPATION FOR USE & LIGHTING INSTRUCTIONS
Curing your grill
Prior to your first use of the Grill, follow the inst ruct ions below ca refully to cu re your grill.
Curing your grill will minimize damage to the exterior finihs as well as rid the grill of paint odor
that ca n impart unnatural flavors to the first meal prepared on the grill.
IMPORTANT: To protect your grill from excessive rust, the unit must be properly cured
and covered at all times when not in use.
Step 1
Do not
Lightly co at all interior su rfaec s of the grill with vegetable oil or vegetable oil sp ray.
co at ch arco al grates or ch arco al ash tray.
Step 2
Follow the instructions
below ca refully to build a fire. You may use ch arco al and/or wood
as fuel in the grill (es e “Adding Charco al/Wood During Cooki ng” se tc ion of this manual).
If usi ng a Charco al Chimney Starter, follow all manufatc urer’s warnings and ints ruct ions
regarding the use of their produtc . Start with 5 pounds (2.3kg ) of hc arco al. This sh ould be
enough ch arco al to oc ok with, once the cu ring proce s has been co mpleted. When ch arco al
is burning st rong, ca refully place hot co als on hc arco al grate.
NOTE: To extend the life of your grill, make sure that hot coals and wood do not touch
the walls of grill.
IF USING CHARCOAL CHIMNEY STARTER, PROCEED TO STEP 5.
ONLY use charcoal lighting fluid
If you ch oose to use ch arco al lighting fluid,
approved for
Do not use gasoline, kerosene, alcohol
lighting ch arco al.
or other flammable material for
lighting ch arco al. Follow all manufact urer’s warnings and inst ruct ions regarding the use of
their product . Start with 8 to 10 pounds (3.6 to 4.5 kg ) of ch arco al. This sh ould be enough
ch arco al to co ok with, once the uc ring proce s has been oc mpleted. Place the ch arco al in the
ce nter of each hc arco al grate.
Step 3
Saturate ch arco al with lighting fluid. With lid open, wait 2 to 3 minutes to allow lighting fluid to
so ak into ch arco al.
Store lighting fluid a safe distance from the grill.
Step 4
With grill lid and doors open, st and back and ca refully light ch arco al through the doors. Allow
to burn until co vered with a light ash (approximately 20 minutes) .
Warning:
Charco al lighting fluid must be allowed to co mpletely burn off prior to cl osi ng grill lid
(approximately 20 minutes) . Failure to do this oc uld trap fumes from ch arco al lighting fluid in
flash-fire or explosion when lid is opened
grill and may resu lt in a
.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5
With co als burning st rong, cl oes the lid. Allow the temperature to reach 225°F (107°C) on
temperature gauge. Maintain this temperature for 2 hours.
Step 6
Incr ease the temperature to 400°F (205°C) on temperature gauge. This ca n be ach ieved by
adding more ch arco al and/or wood (se e “Adding Charco al/Wood During Cooki ng“ se ct ion of
this manual). Maintain this temperature for 1 hour then allow unit to co ol oc mpletely.
NOTE: It is important that the exterior of the grill is not scraped or rubbed
during the curing process.
Adding Charcoal/Wood During Cooking
Additional ch arco al and/or wood may be required to maintain or incr eaes co oki ng temperature.
Step 1
flames can flare-up
Stand back and ca refully open grill lid. Ues ca ution si nce
su ddenly co mes in oc ntact with fire.
when fresh air
Step 2
Wearing oven mitts/gloves
, adjust the hanger so that the ch arco al grate will be on the
place it on a clean and
lowest level of Grill Body. Use lifter to lift up the co oki ng grid and
non-combustible surface
. DO NOT touch the grid by hand.
Step 3
use long cooking tongs
Stand back a sa fe dist ance and
to lightly brush asi de ash es on hot
co als. Use co oki ng tongs to add ch arco al and/or wood to ch arco al grates, being ca reful not to
st ir-up ash es and sp arks. If nece sa ry, use your Charco al Chimney Starter to light additional
ch arco al and/or wood and add to exits ing fire.
WARNING
!
!
fluid to hot or
Never add charcoal lighting
even warm coals as flashback
occur
may
causing severe burns.
Step 4
wear oven mitts/gloves
When ch arco al is burning st rong again,
and ca refully return
ch arco al grates to Grill body with lifter. Extinguish any hot ash es, oc als or embers which may
have fallen from the grill or beneath and around grill.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
AFTER-USE SAFETY
WARNING
!
!
Always
cool completely
�
allow grill and all co mponents to
before handling.
Never leave
unattended
�
co als and ahs es in grill
. Make su re co als and
completely extinguished before removing
ash es are
.
Before grill can be left unattended
�
, remaining co als and ash es must be
removed from grill. Use ca ution to protect yourse lf and property. Place
remaining co als and ash es in a non-co mbust ible metal co ntainer and
saturate with water
co mpletely
. Allow co als and water to remain in metal
co ntainer 24 hours prior to disp osi ng.
coals and ashes
a safe distance from
�
�
Extinguish ed
sh ould be place d
all
structures and combustible materials
.
beneath
With a garden hose , completely wet surface
and around the
grill to extinguihs any ash es, co als or embers which may have fallen during
the co oki ng or lc eaning proce s.
�
Cover and store grill in a protect ed area away from children and pets.
Proper Care & Maintenance
�
�
Cure your grill periodica lly throughout the year to protect against exce is ve rust .
To protect your grill from exce is ve rust , the unit muts be properly cu red and co vered at
all times when not in use .
�
�
Wash co oik ng grills and ch arco al grates with hot, so apy water, rines well and dry. Lightly
co at grills with vegetable oil or vegetable oil sp ray.
Clean insi de and outis de of grill by wiping off with a damp cl oth. Apply a light co at of
vegetable oil or vegetable oil sp ray to the interior su rface to prevent rust ing. Do not co at
ch arco al grates or ch arco al ash tray.
�
�
If rust appears on the exterior us rface of your grill, lc ean and buff the affected area with
st eel wool or fine grit emery cl oth. Touhc -up with a good quality high-temperature
resi st ant paint.
Never apply paint to the interior us rface . Ruts sp ots on the interior us rface ca n be buffed,
cl eaned, and then lightly co ated with vegetable oil or vegetable oil sp ray to minimize
rust ing.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently Asked Questions
Can I convert my gas grill from one fuel source to another?
No. Your gas grill is manufactured to specific standards developed by CSA and ANSI for your safety
and grilling performance for either LP or Natural Gas. We do not offer conversion kits nor do we
recommend you change the fuel type.
How are your grills tested?
Our grills are tested and certified by CSA, a leading worldwide independent testing center, to meet or
exceed various CSA and ANSI standards along with various performance standards. The burners and
gas line in each grill are also individually tested when each grill comes off the assembly line just prior to
packaging. Each burner is ignited for this test.
What is the humming noise I sometimes here coming from my regulator?
The humming sound you can hear is just gas flowing through the regulator. There is no need to be
concerned with a low volume of noise.
My grill has a low flame on some burners, or some burners will not light at all. What can cause this?
This can be caused by the regulator’s flow limiting device, which is generated by a sudden change in
pressure. Opening the tank valve too quickly can cause this. In this case, close the LP tank valve and
disconnect from the regulator. Let it stand for 10 minutes. Reconnect the regulator to the LP tank.
Open the grill lid. Slowly open the LP tank valve. Follow the burner lighting procedures and light the
burner furthest from the LP tank. Continue to light the other burners as you move towards the LP tank.
Can I use ceramic plates, briquettes of any kind, or lava rocks?
No. Your grill is designed for use only with the heat diffusers. Grease drips down on to the diffusers
and is burned, creating steam and additional flavor.
For technical support and replacement parts service
Business hours: Monday through Friday; 8:30AM-5:00PM Central Time.
For customer service please call 1-888-922-2336 or via e-mail at
Do not call store for technical support and replacement part.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
1-888-922-2336
39
Download from Www.Somanuals.com. All Manuals Search And Download.
|