Oregon Scientific Thermometer THT312 User Manual

is in conformity with Part 15 of the FCC Rules. Operation is  
subject to the following two conditions: 1) This device may not  
cause harmful interference. 2) This device must accept any  
interference received, including interference that may cause  
undesired operation.  
HOW TO SET TIME  
HOW TO SECURE THE OUTDOOR  
SENSOR PROBE  
CAUTION  
The contents of this manual is subject to change  
without further notice.  
1. Press [MODE] button for two seconds while in normal  
-
-
-
mode.  
Follow these steps to secure the outdoor sensor probe:  
2. The digits and colon will blink which indicates the time  
settingmode has been enabled.  
1. Drive a screw (not included) along with wire attachment  
into the wall at the location you choose for the external  
sensor.  
Due to printing limitations, the displays shown in this  
manual may differ from the actual display.  
3. Set the hour or minutes by pressing [HR] or [MIN] button,  
The contents of this manual may not be reproduced  
without the permission of the manufacturer.  
EC-DECLARATION OF CONFORMITY  
respectively.  
2. Slip the external sensor into the wire attachment.  
Hereby, Oregon Scientic, declares that this 3-line Indoor  
and Outdoor Thermometer with Clock model THT312 is in  
compliance with the essential requirements and other relevant  
provisions of Directive 1999/5/EC.  
4. Press [MODE] button again to conrm the time setting.  
3-line Indoor and Outdoor  
Thermometer with Clock  
MODEL: THT312  
3. Route the outdoor sensor cord (3 meters or 10 feet) and  
main unit to the desired location.  
NOTE Time setting will be disabled if [MODE] button is  
pressed.  
ABOUT OREGON SCIENTIFIC  
Visit our website (www.oregonscientic.com) to learn more  
about Oregon Scientic products such as digital cameras;  
MP3 players; childrenís electronic learning products and games;  
projection clocks; health and tness gear; weather stations;  
and digital and conference phones. The website also includes  
contact information for our Customer Care department in case  
you need to reach us, as well as frequently asked questions  
and customer downloads.  
USER’S MANUAL  
A copy of the signed and dated Declaration of Conformity  
is available on request via our Oregon Scientic Customer  
Service.  
INDOOR  
OUTDOOR  
HOW TO SET THE ALARM TIME  
1. From the normal mode press [MODE] button to enter alarm  
INTRODUCTION  
mode.  
Thank you for your purchase of this thermometer with  
clock.  
2. Press [MODE] button again and hold for 2 seconds to enter  
OUTDOOR  
SENSOR  
PROBE  
the alarm time setting mode.  
Your thermometer with clock is an example of superior  
design and craftsmanship.  
3. Set the hour or minutes by pressing [HR] or [MIN] button,  
respectively.  
In order to optimize its function, be sure to read this  
instruction manual carefully before use.  
We hope you will nd all the information you need on our  
website, however if youíre in the US and would like to contact  
the Oregon Scientic Customer Care department directly,  
please visit:  
COUNTRIES RTTE APPROVAL COMPLIED  
4. Press [MODE] button again to conrm the alarm time  
setting.  
All EC countries, Switzerland CH  
Keep this instruction manual handy for future references.  
5. Toggle the [ALARM ON/OFF] key on back of product to  
and Norway  
H
enable/disable alarm function.  
www2.oregonscientic.com/service/support  
NOTE A bell icon [  
activated.  
] on the display will indicate alarm is  
FEATURES  
WIRE ATTACHMENT  
SCREW  
OR  
Three line LCD display, shows clock, indoor & outdoor  
temperature.  
Call 1-800-853-8883.  
Daily 1-minute alarm with 8-minute snooze function.  
User selectable 12 or 24-hour display format.  
User selectable °C or °F temperature units of measure.  
ABOUT THE LIGHT & SNOOZE FUNCTION  
NOTE Place the outdoor sensor probe away from direct sunlight  
and heavy precipitation.  
1. When the [LIGHT/SNOOZE] button is pressed, the backlight  
will stay lit for 5 seconds before turning off if no key is  
pressed.  
For international inquiries, please visit:  
www2.oregonscientic.com/about/international/default.asp  
Displays min. and max. temperature units for indoors &  
outdoors.  
2. When alarm sounds the backlight will come on automatically  
and pressing the [LIGHT/SNOOZE] button will activate the  
snooze function.  
MAINTENANCE  
FCC STATEMENT  
External sensor probe with 3-meter or 10-feet long cable.  
LED backlight for viewing in the dark.  
5-second backlight delay  
When handled properly, this unit is engineered to give you  
years of satisfactory service. Here are a few product care  
instructions:  
This device complies with Part 15 of the FCC Rules. Operation  
is subject to the following two conditions: (1) This device may  
not cause harmful interference, and (2) This device must accept  
any interference received, including interference that may cause  
undesired operation.  
1. Do not immerse the unit in water. If the unit comes in contact  
with water, dry it immediately with a soft lint-free cloth.  
HOW TO STOP THE ALARM  
Desktop or wall mount feature.  
When alarm sounds, press any button (expect [LIGHT/  
SNOOZE] button) to stop the alarm.  
2. Do not clean the unit with abrasive or corrosive materials.  
Abrasive cleaning agents may scratch the plastic parts and  
corrode the electronic circuit.  
DISCRIPTION OF PARTS  
WARNING Changes or modications not expressly approved  
by the party responsible for compliance could void the user’s  
authority to operate the equipment.  
LCD DISPLAY  
12/24. SWITCH  
3. Do not subject the unit to excessive force, shock, dust,  
temperature, or humidity. Such treatment may result  
in malfunction, a shorter electronic life span, damaged  
batteries, or distorted parts.  
HOW TO VIEW THE OUTDOOR & INDOOR  
TEMPERATURE MEMORY  
WALL  
HANGER  
1. While in normal mode (Fig. A) press the [MEM/CLEAR]  
button once to view the outdoor & indoor max. temperature.  
(Fig. B)  
NOTE This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant to Part  
15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a  
residential installation.  
4. Do not tamper with the unit’s internal components. Doing so  
will terminate the unit’s warranty and may cause damage.  
The unit contains no user-serviceable parts.  
HOUR  
MIN  
2. Press again to view the indoor & outdoor min. temperature.  
ALARM  
ON/OFF  
(Fig. C)  
5. Only use new batteries as specied in this instruction  
manual. Do not mix new and old batteries as the old  
batteries may leak.  
3. Press the key the third time to return to normal mode  
displaying current time and current indoor & outdoor  
temperature. (Fig. A)  
This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in accordance  
with the instructions, may cause harmful interference to  
radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this  
equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference  
by one or more of the following measures:  
6. Read this instruction manual thoroughly before operating  
the unit.  
FIG.A  
FIG.B  
FIG.C  
WIRE ATTACHMENT  
FREE STAND AND WALL MOUNTING  
STAND  
MODE  
MEMORY/  
CLEAR  
OUTDOOR TEMPERATURE  
SENSOR PROBE  
SNOOZE/  
LIGHT  
Stand:  
Flip out the plastic stand on the rear of the thermometer for table  
Reorient or relocate the receiving antenna.  
standing. Stand the thermometer on a at surface.  
FRONT VIEW  
REAR VIEW  
Increase the separation between the equipment and  
receiver.  
Wall Mount:  
NORMAL MODE  
Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
You can mount your thermometer on a wall by using a screw  
(not included) with the screw head extending about 1/8 inches  
(3.5mm ) from the wall.  
In normal viewing mode the LCD will display the current time  
on the rst line. The second line will display the current indoor  
temperature with the third line displaying the current outdoor  
temperature.  
Consult the dealer or an experienced radio / TV technician  
for help.  
NORMAL MODE  
MAX. MODE  
MIN. MODE  
SPECIFICATIONS  
HOW TO CLEAR THE TEMPERATURE  
MEMORY  
DECLARATION OF CONFORMITY  
Indoor measurement range:  
23°F to 122°F (-5°C to 50°C)  
The following information is not to be used as contact for support  
or sales. Please call our customer service number (listed on our  
website at www.oregonscientic.com), or on the warranty card  
for this product) for all inquiries instead.  
Outdoor measurement range: -58°F to 158°F (-50°C to 70°C)  
Press and hold the [MEM/CLEAR] button for 2 seconds. This  
will clear both the outdoor and indoor temperature memory to  
the current temperature reading.  
Temperature resolution:  
Measuring accuracy:  
0.2°F(0.1°C)  
+/-2.0°F for 32°F to 104°F  
(+/-1.0°C for 0°C to 40°C)  
+/-4.0°F for -8°F to 122°F  
(+/-2.0°C for -40°C to 50°C)  
We  
HOW TO SELECT THE TEMPERATURE  
UNIT OF MEASURE  
Name:  
Oregon Scientic, Inc.  
19861 SW 95th Ave.,  
Tualatin, Oregon 97062 USA  
1-800-853-8883  
+/-6.0°F for -58°F to 158°F  
(+/-3.0°C for -50°C to 70°C)  
Address:  
The thermometer can select between degrees Celsius and  
Fahrenheit readings by sliding the [°C /°F ] button up for degree  
Celsius and down for degree Fahrenheit.  
Telephone No.:  
Fax No.:  
NORMAL MODE  
Temperature sensing  
Sampling cycle:  
1-503-684-3332  
10 seconds  
Clock accuracy:  
+/-0.5 second / day.  
HOW TO SELECT THE HOUR DISPLAY  
FORMAT  
HOW TO INSTALL AND REPLACE BATTERY  
declare that the product  
Outer dimensions:  
4.33x2.51x.0.7 inches  
(105 x 64 x 18 mm)  
(L x W x H)  
The Thermometer uses two pieces of UM-4 or ‘AAA’ size  
batteries. Follow these steps to install/replace battery:  
The clock can be either in a 12 or 24-hour format depending on  
the format selected by user. To select the 12-hour format slide  
the [12HR/24HR] button up and down for 24-hour format.  
Product No.:  
THT312  
1. Remove battery cover on the back of the unit by gently  
pressing down on the arrow and slide in the direction it is  
pointing.  
Power Source :  
Uses 2 pieces UM4 or ‘AAA’  
size 1.5V batteries.  
Product Name:  
3-line Indoor and Outdoor  
Thermometer with Clock  
Product Weight (exclude battery) : 3.17 ounces (90 g)  
Manufacturer:  
Address:  
IDT Technology Limited  
2. Insert the new batteries. Be sure to follow the polarity  
symbols as marked inside the battery compartment.  
HOW TO RESET THE UNIT  
Block C, 9/F, Kaiser Estate,  
Phase 1,41 Man Yue St.,  
Hung Hom, Kowloon,  
Hong Kong  
If your clock/thermometer does not operate properly, reset  
the unit by pressing the reset key located inside the battery  
compartment.  
3. Replace the battery cover.  
© 2005 Oregon scientic. All rights reserved.  
086-001763-182  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT312_M_EN_op.indd  
1
2005.7.7, 1:58:53 PM  

Miele Dishwasher ESS 3060 10 User Manual
Miller Electric Welding System 145 DX User Manual
Milwaukee Portable Stereo System 49 24 0200 User Manual
MTD Blower 242 692A User Manual
N Tron Switch 509FX User Manual
Oki Printer 8w User Manual
Olympus Camera Accessories Motor Drive 2 User Manual
Omega Engineering Marine Instruments iBTX M User Manual
Oster Mixer 111805 003 User Manual
Panasonic Answering Machine KX TS560ML User Manual