®
S I M P L Y
A M A Z I N G
USER’S GUIDE
XL36R7HH
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATING CLEANER,
READ ALL INSTRUCTIONS IN
THIS MANUAL CAREFULLY.
IMPORTANT SAFETY
INSTRUCTIONS
When using an electrical appliance, basic
precautions should always be followed,
including the following:
Table of Contents
Maintenance, Accessories, Important Safety Instructions . . . . page
Warranty, Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . page
2
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER
3
Parts List, Assembly, Operating Instructions,
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page
4
WARNING
To Replace Filter Dust Bag, How to Replace a Worn Belt,
To Adjust or Replace Brush, Using an Oreck Fresh Air® Tab,
Bulb Replacement, Stuffing or Blockage . . . . . . . . . . . . . . . . . page
To reduce the risk of fire,
electric shock, or injury:
5
• Do not leave appliance unattended when plugged in.
Unplug from outlet when not in use and before servicing.
• Do not use outdoors or on wet surfaces.
• Do not operate the unit while in the upright and locked
position.
• Do not let the unit run while in any one stationary position
for any period of time. Keep the unit moving while in
operation.
Maintenance and Customer Service
Your Oreck vacuum cleaner is a product of precise engineering. The
motor bearings are permanently lubricated and should not be oiled.
Save your sales or purchase slip. Should your Oreck appliance require
warranty service, present this slip to the Authorized Service Center as
your proof of purchase date.
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
• Use only as described in this manual. Use only
manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not
working as it should, has been dropped, damaged, left
outdoors, or dropped into water.
• Do not pull or carry by cord, use cord as a handle, close
door on cord, or pull cord around sharp edges or corners.
Keep cord away from heated surfaces.
Accessories (Sold Separately)
ITEM
PART #
CCPK8DW
CCPK8
1. Dust Bag, 8 Pack, Saniseal®Hypo-Allergenic
Dust Bag, 8 Pack, Regular
2. Belts, 3 Pack
0300604
AIRTABS
00965-0019
3. Oreck Fresh Air® Tabs
4. Light Bulb
• Do not run appliance over cord.
• Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any
opening blocked; keep free of dust, lint, hair and anything
that may reduce air flow.
• Keep hair, loose clothing, fingers and all parts of body
away from openings and moving parts.
• Do not use to pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
• Do not use without filter bag assembly in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids,
such as gasoline or lighter fluid, or use in areas where
they may be present.
• Do not use appliance in an enclosed space where
flammable, explosive or toxic vapors are given off by oil
base paint, paint thinner, some mothproofing substances,
or in an area where flammable dust is present.
• Do not pick up toxic material such as chlorine bleach,
drain cleaner, gasoline, etc. with this appliance.
• Use caution when vacuuming over area rug edges and
fringe.
SAVE THESE INSTRUCTIONS
Household Use Only
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Troubleshooting Guide
Alexander Nevsky Enterprises Inc. warrants the normal use of electrical
products during the warranty period if such products were used in accor-
dance with the user’s guide instructions.
WARNING: Unplug cord from electrical
outlet before servicing.
The product must be purchased from Alexander Nevsky Enterprises Inc.
or a retail dealer authorized by Alexander Nevsky Enterprises Inc. If you
purchase this product from any other source, Alexander Nevsky
Enterprises Inc. grants you no warranty and you, not Alexander Nevsky
Enterprises Inc., assume the entire responsibility for the quality of this
product including the entire cost of any necessary servicing or repairs of
any defects.
SAVE SERVICE CALLS...CHECK THESE FIRST:
• Is the disposable filter dust bag full?
• Are pores of filter dust bag clogged with powder or fine dust?
• Is anything clogging the revolving brush, lower tube, intake opening,
fan housing or connector assembly opening?
• Is the belt in place and turning the brush?
• Are the brush ends in the proper location?
The warranty period is three (3) years; ten years (10) for the housing. The
duration of your warranty period begins with the day of your purchase with
the condition that you have a correctly completed warranty certificate and
only under the conditions of normal domestic use. If the product is used
for commercial purposes as in restaurants, café’s, hotels, etc. this limited
warranty is automatically voided.
• Does the brush turn freely? Are hair, string or rug fibers wound around
the brush?
PROBLEM
CLEANER
POSSIBLE SOURCE
Not plugged in
properly.
AREAS TO CHECK
Be sure cleaner is
firmly plugged into
wall outlet.
At your demand, any service center authorized by Alexander Nevsky
Enterprises Inc. will replace and/or repair all manufacturer’s defects free
of charge during the warranty period. Information about our service
centers in your region can be obtained from your sales person.
WILL NOT RUN
No electricity in wall
outlet.
Check electrical
source–fuse or
circuit breaker.
ATTENTION!
Be sure to check the accuracy of the warranty certificate, the signature of
the sales person, the correct date of purchase and stamp on the warranty
certificate!
CLEANER
DOES NOT PICK UP
Filter bag is full.
Replace filter bag.
See “To Replace
Paper Filter Dust
Bag.”
This warranty doesn’t apply in cases of:
• abuse
Nozzle or intake
pivot clogged.
Clear obstruction.
Replace belt.
• misuse
• incorrect warranty certificate or if changes have been made to the
warranty certificate
Belt is broken or
stretched.
• intentional damage to product or the traces of inappropriate chemical
agents
Brush is worn.
See “To Adjust or
Replace Brush.”
• damages made by animals or insects
• the use of incorrect voltage other than indicated on the serial
number plate
• using the product in a different manner than it was produced for
Bag tube clogged.
Clear obstruction.
Change bag.
• repairs, other intrusive procedures or the disassembling of the unit
performed by non-authorized repair facilities
Bag pores are
clogged with fine
dust.
• using other than manufacturer replacement parts
• damages caused by fire, flood or other reasons which are out of the
control of the manufacturer or the sales person of this product
Impeller fan is
broken.
Return to Service
Center for repair.
Drive belts, revolving brushes, bulbs, disposable bags and other parts
subject to normal wear are not covered by this warranty. The amount of
warranty repairs cannot exceed the original purchase price.
Revolving brush is
not even at both
ends.
Check brush roll end
cards. Make sure
words “OLD” or
“NEW” match at
ALL OTHER SERVICING SHOULD BE DONE BY AN
AUTHORIZED SERVICE CENTER.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
objects, it is recommended that these be removed from the floor
before you vacuum. Failure to do so may result in permanent
damage to the motor suction fan and its housing.
Parts List
To assist you in identifying components of your vacuum, the parts have
been numbered as follows:
5. WARNING: Do not use your vacuum cleaner on damp or wet
surfaces. This will cause damage to the vacuum cleaner and is
dangerous to the user. Damage caused by use on wet or damp
surfaces is not covered under warranty.
10
1
2
3
4
5
6
7
8
9
Handle section, upper
Tube, lower
Power head
Outer bag
Paper filter dust bag
Power cord
Retaining spring
Bag tension bar
Zip fastener
11
9
6. REPLACE THE BELT EVERY 6 MONTHS.
1
12
7. Change the disposable filter dust bag at least once a month—
even if it is not full! The collected dust in the dust bag can cause
odor, attract moisture, and can affect the efficiency of the cleaner.
8. DO NOT run the vacuum cleaner over the cord. The revolving
brush could damage the cord.
13
5
9. Use caution when vacuuming over area rug edges and fringe.
4
10 On/Off switch
11 Cord hook
General Information
2
6
12 Plastic loop/cable clamp
13 Connector assembly
14 Fan housing
The performance of your new cleaner greatly depends upon care and
maintenance. The instructions in this manual will guide you in
performing basic care and maintenance. To obtain the most satisfying
years of service read the instructions and keep them handy for future
reference.
15 Cord assembly
14
7
8
15
3
Disposable Paper Filter Dust Bags
Assembly
Disposable paper filter dust bags play a very important role in the
efficiency of your ORECK vacuum cleaner. The purpose of the filter bag
is to trap dirt, but at the same time it must be porous enough to allow air
to pass through. If the paper bag becomes clogged, no air can pass
through the cleaner and cleaning cannot take place, regardless of the
cleaner’s power. Increase the CLEANING POWER of your cleaner by
changing the bag at least once a month–even if it is not full!
fig. 1 Before assembling appliance, remove two screws from
connector assembly. Remove cardboard insert by pulling
upward.
fig. 2 With On/Off switch facing the front of the unit, slide upper handle
section over matching section of the connector assembly. Insert
short screw into top hole and long screw into bottom hole then
tighten firmly until handle is no longer loose.
DO NOT FILL ABOVE THE LINE INDICATED ON THE DUST BAG.
Be sure the disposable paper filter dust bag is installed properly.
fig. 3 Attach cord to cord clip by pressing cord above and below clip
All paper dust bags are not the same. Your ORECK disposable
dust bags have been designed to be used with the ORECK cleaner.
Using bags other than genuine ORECK TYPE CC disposable bags
will affect the cleaning ability of your cleaner and could cause
damage to it.
ensuring the cord is fully rested in clip.
Operating Instructions
The Belt
Make sure disposable paper filter dust bag is in place. DO NOT operate
the cleaner without a paper filter dust bag. Plug the power cord into an
electrical outlet and press the On(l) - OFF(O) switch on handle assembly
when ready to operate.
The belt on your vacuum cleaner controls the speed of the revolving
brush and is very important for the effective operation of the cleaner. If
the belt becomes stretched or cut, it will cause the revolving brush to
stop completely or slow down. See instructions in the manual for
replacing belt.
Up-Position Lock
fig. 4 Place foot on power head and lean handle back gently to release
lock for vacuum use. Return handle to the full upright position to
engage lock.
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts. Belts
other than Oreck belts will not operate the revolving brush
correctly and may create undue stress which will cause damage to
the motor and brush bearings. Using belts other than ORECK belts
will void the warranty.
NOTE: Do not operate the unit while in the upright and locked position.
Do not let the unit run while in any one stationary position for any period
of time. Keep the unit moving while in operation.
For Easy Power Cord Storage
Lubrication
fig. 5 Wrap power cord around cord hook on handle and cord hook on
The vacuum cleaner motor bearings are factory lubricated and sealed.
Further lubrication is not required.
connector.
fig. 6 To release cord, twist cord dump located on Helping Hand®
General Cleaner Care
handle 1/2 turn. Slide cord off handle.
At least once a month, check for and
remove excessive lint, string or hair from
revolving brush.
Operating Recommendations
This new ORECK XL High-Speed Upright is one of the finest, fastest,
and strongest units in its class. You’ll love the way it cleans, gets under
things, and it’s SO lightweight and easy to use.
Wipe the outside of the cleaner with a
damp cloth. Also clean the connector
deflector assembly area, base of cleaner
and fan housing area. If there is dust in
the outer bag, vacuum it or shake it out.
The following are a few simple suggestions regarding its operation:
1. When inserting a new disposable paper filter dust bag—FIRST
PUFF OUT and OPEN THE BAG.
A little preventative maintenance will keep
your cleaner looking new and will ensure
continued cleaning effectiveness.
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or makes an
unusual noise, STOP OPERATION and service.
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor
Surfaces and Polished Floor Finishes
4. Although your upright will pick up pins, paper clips, and other small
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Use floor and floor finish manufacturer’s recommended methods of
cleaning. The metal strip on the base of the cleaner could be damaged
if used on concrete or abrasive surfaces, and, therefore, cause damage
to wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished
floor finishes. The roller brush may also scuff very soft finishes. Do not
operate the unit while in the upright and locked position. Do not let the
unit run while in any one stationary position for any period of time. Keep
the unit moving while in operation.
fig. 17 Reassemble the belt and the baseplate and check bristle height
above baseplate at each end of brush.
If a previous adjustment has already been made and bristle height does
not extend above baseplate, a new brush assembly should be ordered.
IMPORTANT: Unless the brush is worn as indicated above, both
bearings must be in the “NEW” position. When rotating, both
bearings must be in the “OLD” position. Unmatched settings will
cause damage to your machine.
Using an Oreck Fresh Air® Tab
XL36R7HH: Celoc® Hypo-Allergenic Filter System
The Celoc SMMS outer bag of your vacuum cleaner is high filtration
medical material designed to filter the smallest of dust particles. It is
important the inside of the outer bag be cleaned. Hand wash the outer
bag, turned inside out with warm water and allow it to air dry. For best
results, the Celoc SMMS outer bag should be replaced once a year.
The Celoc layered disposable inner dust bag must be replaced once a
month even if it is not full. Change it more often if it is used in extremely
dirty areas. Increase the cleaning power of your vacuum by changing
the bag often.
fig. 21 Your ORECK XL vacuum cleaner has a special ORECK FRESH
AIR® tab pocket. This light-colored pocket is located inside the
vinyl bag in the area where the paper disposable bag attaches
to the intake tube. Insert tablet in pocket if desired.
Bulb Replacement
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 22 Remove lamp housing by removing two (2) screws in the the
top of the lamp housing. Pull burned out bulb from holder and
replace with new bulb. Use only Oreck replacement parts.
Reassemble lamp housing by replacing two screws in the top of
the lamp housing.
To Replace Filter Dust Bag
WARNING: Unplug cord from electrical
outlet before servicing.
BAG REMOVAL:
Stuffing or Blockage
fig. 7 Unzip outer bag completely.
fig. 8 Pull bag cardboard collar to release bag dock door from
IMPORTANT: On plush and new carpets, stuffing may occur inside the
the intake tube and the lower tube assembly. This is due to excessive fuzz
and loose cuttings in the carpet. Stuffing could occur for the first few
cleanings until all the loose material is removed. Due to the high efficiency
of the cleaner, many older carpets will cause stuffing when the cleaner is
first used on them. If your vacuum cleaner does not pick up properly, or
makes unusual noise and the outer bag does not fluff up or balloon open,
follow these steps:
connector. Bag dock door will hinge downward.
fig. 9 Gently pull bag cardboard collar upward out of the bag dock.
The dust seal will close automatically.
BAG INSTALLATION:
fig. 10 Slide the cardboard collar completely onto bag dock door.
fig. 11 Firmly push bag dock door with both thumbs on indication point
until it snaps.
WARNING: Unplug cord from electrical
outlet before servicing.
How to Replace a Worn Belt
fig. 23 Check for blockage at the mouth of the intake opening. If there
is blockage, remove it with long-nose pliers, a screwdriver or
coat hanger. If you can not reach the blockage, remove
baseplate (fig. 24).
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 12 Remove the replacement belt from the storage channel.
fig. 25 If the blockage is not at the base, remove lower tube. Unhook
fig. 13 Remove the door by removing the hold down screw located on
retainer spring, releasing bottom of bag.
side of power head.
fig. 26 Twist lower collar counterclockwise to slide up. Pull tube out of
fig. 14 Slide the door forward by prying open with a screwdriver or coin.
base.
fig. 15 Remove the belt from the motor drive shaft and brush roll pulley.
fig. 27 Check for blockage. If blockage is in the tube, remove with a
fig. 16 Loop the new belt over the motor drive shaft. Place the
opposite end of the belt on the brush roll pulley. Rotate the
brush roll three (3) complete revolutions to ensure that no part
of the belt is overhanging the end of the motor drive shaft.
coat hanger.
fig. 28 If tube is not blocked, look into fan housing. Remove debris
with long-nose pliers, a screwdriver or coat hanger.
fig. 29 To reassemble, check O-ring on tube, and replace if damaged.
Vacuum will not operate properly without the tube O-ring. Slide
O-ring to approximately 2" from base of tube. Replace tube by
first lining up slot at base of tube with inner tab inside fan
housing. Then reinsert tube and push down until the tube is
seated. Make sure O-ring is in place against fan housing
opening. Replace and tighten collar until collar locking tabs are
locked in place.
fig. 14 Replace the door by sliding it into the groove at the bottom of
the housing.
fig. 13 Replace the hold down screw and tighten.
To Adjust or Replace Brush
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 27 Make sure collar is not cross threaded on housing. Reattach
bag spring (fig. 25).
fig. 17 To determine if the brush is worn, place a firm straight edge
across the nozzle opening. If brush bristles do not extend
beyond baseplate, brush should be adjusted.
fig. 30 Many times blockage occurs due to a full dust bag causing dirt to
back down the air flow system. When that happens, the
blockage will be at the top of the system, starting in the area
where the dust bag connects to the connector assembly.
fig. 18 Remove the baseplate by removing 5 screws.
fig. 19 Remove the belt and brush roll from the housing.
fig. 20 Rotate both bearing assemblies at ends of brush roll to show
"OLD" and replace in the holding channels in the housing.
NOTE: The bearing assembly setting marked "OLD" has no ribs on the
top of the assembly. The one marked "NEW" has several ribs. When
rotating bearings, make sure both bearing assembly settings are the
same and face up when replacing the brush roll.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
©2005 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck
Holdings, LLC. Printed in America.
75663-02 REV A
01/05 ECN# R-7746
Download from Www.Somanuals.com. All Manuals Search And Download.
|