Onkyo Stereo Receiver HT R391 User Manual

Contents  
AV RECEIVER  
Safety Information and Introduction ............2  
Table of Contents...........................................6  
Connections .................................................12  
Turning On & Basic Operations..................20  
Advanced Operations ..................................37  
Controlling Other Components...................48  
HT-R391  
Instruction Manual  
Appendix.......................................................54  
Speaker Package  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Safety Information and Introduction  
5. Preventing Hearing Loss  
For U.S. models  
FCC Information for User  
CAUTION:  
The user changes or modifications not expressly approved  
by the party responsible for compliance could void the  
user’s authority to operate the equipment.  
Precautions  
Caution  
Excessive sound pressure from earphones and  
headphones can cause hearing loss.  
6. Batteries and Heat Exposure  
Warning  
1. Recording Copyright—Unless it’s for personal use  
only, recording copyrighted material is illegal without  
the permission of the copyright holder.  
2. AC Fuse—The AC fuse inside the unit is not user-  
serviceable. If you cannot turn on the unit, contact your  
Onkyo dealer.  
Batteries (battery pack or batteries installed) shall not  
be exposed to excessive heat as sunshine, fire or the  
like.  
NOTE:  
3. Care—Occasionally you should dust the unit all over  
with a soft cloth. For stubborn stains, use a soft cloth  
dampened with a weak solution of mild detergent and  
water. Dry the unit immediately afterwards with a  
clean cloth. Don’t use abrasive cloths, thinners,  
alcohol, or other chemical solvents, because they may  
damage the finish or remove the panel lettering.  
4. Power  
This equipment has been tested and found to comply with  
the limits for a Class B digital device, pursuant to Part 15  
of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a  
residential installation.  
This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful  
interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more  
of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and  
receiver.  
• Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician  
for help.  
7. Never Touch this Unit with Wet Hands—Never  
handle this unit or its power cord while your hands are  
wet or damp. If water or any other liquid gets inside  
this unit, have it checked by your Onkyo dealer.  
8. Handling Notes  
• If you need to transport this unit, use the original  
packaging to pack it how it was when you originally  
bought it.  
• Do not leave rubber or plastic items on this unit for a  
long time, because they may leave marks on the  
case.  
• This unit’s top and rear panels may get warm after  
prolonged use. This is normal.  
• If you do not use this unit for a long time, it may not  
work properly the next time you turn it on, so be sure  
to use it occasionally.  
WARNING  
BEFORE PLUGGING IN THE UNIT FOR THE  
FIRST TIME, READ THE FOLLOWING SECTION  
CAREFULLY.  
AC outlet voltages vary from country to country. Make  
sure that the voltage in your area meets the voltage  
requirements printed on the unit’s rear panel (e.g., AC  
230 V, 50 Hz or AC 120 V, 60 Hz).  
The power cord plug is used to disconnect this unit  
from the AC power source. Make sure that the plug is  
readily operable (easily accessible) at all times.  
For models with [POWER] button, or with both  
[POWER] and [ON/STANDBY] buttons:  
Pressing the [POWER] button to select OFF mode  
does not fully disconnect from the mains. If you do not  
intend to use the unit for an extended period, remove  
the power cord from the AC outlet.  
For models with [ON/STANDBY] button only:  
Pressing the [ON/STANDBY] button to select  
Standby mode does not fully disconnect from the  
mains. If you do not intend to use the unit for an  
extended period, remove the power cord from the AC  
outlet.  
En-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Safety Information and Introduction  
For Canadian Models  
NOTE: THIS CLASS B DIGITAL APPARATUS  
COMPLIES WITH CANADIAN ICES-003.  
For models having a power cord with a polarized plug:  
CAUTION: TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,  
FULLY INSERT.  
Modèle pour les Canadien  
REMARQUE: CET APPAREIL NUMÉRIQUE DE LA  
CLASSE B EST CONFORME À LA NORME NMB-003  
DU CANADA.  
Sur les modèles dont la fiche est polarisée:  
ATTENTION: POUR ÉVITER LES CHOCS  
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS  
LARGE DE LA FICHE DANS LA BORNE  
CORRESPONDANTE DE LA PRISE ET POUSSER  
JUSQU’AU FOND.  
En-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Safety Information and Introduction  
Aiming the remote controller  
To use the remote controller, point it at the AV receiver’s  
remote control sensor, as shown below.  
Installing the batteries  
Supplied Accessories  
Make sure you have the following accessories:  
Indoor FM antenna (page 19)  
Remote control sensor  
AV receiver  
AM loop antenna (page 19)  
Power cord (Brazilian models) (page 19)  
Remote controller (RC-799M) and two batteries (AA/R6)  
Quick Start Guide  
*
In catalogs and on packaging, the letter at the end of the product  
name indicates the color. Specifications and operations are the  
same regardless of color.  
Approx. 16 ft. (5 m)  
Batteries (AA/R6)  
Note  
• If the remote controller doesn’t work reliably, try replacing the  
batteries.  
• Don’t mix new and old batteries or different types of batteries.  
• If you intend not to use the remote controller for a long time,  
remove the batteries to prevent damage from leakage or  
corrosion.  
• Remove expired batteries as soon as possible to prevent damage  
from leakage or corrosion.  
Thank you for purchasing an Onkyo AV Receiver.  
Please read this manual thoroughly before making  
connections and plugging in the unit.  
Following the instructions in this manual will  
enable you to obtain optimum performance and  
listening enjoyment from your new AV Receiver.  
Please retain this manual for future reference.  
En-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Safety Information and Introduction  
Using Basic Functions...............................................28  
Using the Listening Modes .......................................28  
Using the Home Menu..............................................33  
Selecting Speakers A and B.....................................33  
Using the Sleep Timer ..............................................34  
Setting the Display Brightness..................................34  
Displaying Source Information..................................34  
Changing the Input Display.......................................35  
Using the Music Optimizer........................................35  
Muting the AV Receiver............................................35  
Using Headphones ...................................................36  
Recording .................................................................36  
Table of Contents  
Appendix  
Troubleshooting......................................................... 54  
Connection Tips and Video Signal Path .................. 59  
Using an RIHD-compatible TV, Player,  
or Recorder .............................................................. 60  
About HDMI................................................................. 62  
USB Features.............................................................. 63  
License and Trademark Information ........................ 64  
Specifications............................................................. 65  
Safety Information and Introduction  
Important Safety Instructions......................................2  
Precautions ...................................................................3  
Supplied Accessories...................................................5  
Table of Contents..........................................................6  
Features.........................................................................7  
Front & Rear Panels......................................................8  
Front Panel..................................................................8  
Rear Panel ................................................................10  
Remote Controller.......................................................11  
Controlling the AV Receiver......................................11  
To reset the AV receiver to its factory defaults, turn it  
on and, while holding down VCR/DVR, press  
8ON/STANDBY (page 54).  
On-screen Setup.........................................................37  
Common Procedures in Setup Menu........................37  
Setup menu items.....................................................38  
HDMI Input................................................................39  
Component (Component Video Input)......................39  
Digital Audio (Digital Audio Input).............................40  
Sp Config (Speaker Configuration)...........................40  
Sp Distance (Speaker Distance)...............................41  
Level Cal (Level Calibration).....................................41  
Audio Adjust..............................................................42  
Source Setup............................................................43  
Hardware ..................................................................44  
HDMI Setup ..............................................................45  
Using the Audio Settings ..........................................46  
Connections  
Connecting the AV Receiver......................................12  
Connecting Your Speakers .......................................12  
About AV Connections..............................................15  
Connecting Components with HDMI.........................16  
Connecting Your Components..................................17  
Connecting Onkyo uComponents.........................18  
Connecting a Recording Component........................18  
Connecting the Antennas..........................................19  
Connecting the Power Cord......................................19  
Controlling Other Components  
Turning On & Basic Operations  
iPod/iPhone Playback via Onkyo Dock ....................48  
Using the Onkyo Dock..............................................48  
Controlling Your iPod/iPhone....................................49  
Controlling Other Onkyo Components.....................50  
Preprogrammed Remote Control Codes ..................50  
Entering Remote Control Codes...............................50  
Connected via u..................................................50  
Resetting the REMOTE MODE Buttons ...................51  
Resetting the Remote Controller ..............................51  
Controlling Other Components .................................52  
Turning On/Off the AV Receiver................................20  
Turning On ................................................................20  
Turning Off ................................................................20  
Playback ......................................................................21  
Playing the Connected Component ..........................21  
Controlling Contents of USB Devices .......................22  
Playing an iPod/iPhone via USB...............................23  
Playing a USB Device...............................................24  
Listening to AM/FM Radio.........................................25  
En-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Safety Information and Introduction  
Connections  
Features  
• 4 HDMI Inputs and 1 Output  
Amplifier  
• Onkyo pfor System Control  
• 3 Digital Inputs (2 Optical/1 Coaxial)  
• Component Video Switching (2 Inputs/1 Output)  
• Front-Panel USB Input for Memory Devices and  
• 110 Watts/Channel @ 6 ohms (FTC)  
• 100 Watts/Channel @ 6 ohms (IEC)  
• 120 Watts/Channel @ 6 ohms (JEITA)  
• Optimum Gain Volume Circuitry  
• H.C.P.S. (High Current Power Supply) Massive High  
Power Transformer  
®
®
iPod /iPhone models  
Miscellaneous  
• 40 FM/AM Presets  
• EX.BASS for natural deeper bass  
• Crossover Adjustment  
(40/50/60/70/80/90/100/120/150/200 Hz)  
• A/V Sync Control Function (up to 400 ms)  
• Auto Standby Function  
Processing  
• HDMI (Audio Return Channel, 3D, DeepColor,  
x.v.Color, Lip Sync, DTS-HD Master Audio, DTS-HD  
High Resolution Audio, Dolby TrueHD, Dolby Digital  
Plus, DSD and Multi-CH PCM)  
• On-Screen Display via HDMI  
• Non-Scaling Configuration  
• A-Form Listening Mode Memory  
• Direct Mode  
• Music Optimizer for Compressed Digital Music files  
• 192 kHz/24-bit D/A Converters  
• Powerful and Highly Accurate 32-bit Processing DSP  
• Jitter Cleaning Circuit Technology  
En-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Safety Information and Introduction  
Front & Rear Panels  
Front Panel  
(North American and Brazilian models)  
(Asian models)  
u
a
b cd e f  
g h i j k l m  
n
o p  
q
r
s t  
For detailed information, see the pages in parentheses.  
a 8ON/STANDBY button (20)  
b HDMI THRU indicator (45)  
c SPEAKERS A and B buttons (33)  
d Remote control sensor (5)  
j DISPLAY button (34)  
t USB port (17)  
k SETUP button (37)  
u RT/PTY/TP button (Asian models) (26)  
l TUNING q/w, PRESET e/r(25), cursor and  
m RETURN button  
n MASTER VOLUME control (21)  
o MUSIC OPTIMIZER button (35, 47)  
p PHONES jack (36)  
e LISTENING MODE buttons (28)  
f Display (9)  
g DIMMER button (North American and Brazilian  
models) (34)  
q TONE and Level buttons (46)  
r Input selector buttons (21)  
s AUX INPUT AUDIO and VIDEO jacks (17)  
h MEMORY button (26)  
i TUNING MODE button (25)  
En-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Safety Information and Introduction  
Display  
a b  
c
d
e
g
h
f
For detailed information, see the pages in parentheses.  
a A and B speaker indicators (33)  
b M.Opt indicator (35, 47)  
c Listening mode and format indicators (28, 44)  
d Tuning indicators  
RDS indicator (excluding North American and  
Brazilian models) (26)  
AUTO indicator (25)  
TUNED indicator (25)  
FM STEREO indicator (25)  
e SLEEP indicator (34)  
f HDMI indicator (45, 59)  
g MUTING indicator (35)  
h Message area  
En-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Safety Information and Introduction  
Rear Panel  
(North American and Asian models)  
(Brazilian models)  
e
a b c  
d
f
j
h
i
g
a DIGITAL IN COAXIAL and OPTICAL jacks  
b COMPONENT VIDEO IN and OUT jacks  
c HDMI IN and OUT jacks  
h Composite video and analog audio jacks  
(BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN,  
GAME IN, TV/CD IN)  
i MONITOR OUT V jack  
d FM ANTENNA jack and AM ANTENNA terminal  
e SPEAKERS terminals  
j AC INLET (Brazilian models)  
(FRONT A, CENTER, SURROUND,  
SUBWOOFER, FRONT B)  
See “Connecting the AV Receiver” for connection  
(pages 12 to 19).  
f Power cord (North American and Asian models)  
g u REMOTE CONTROL jack  
En-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Safety Information and Introduction  
Controlling the tuner  
To control the AV receiver’s tuner, press AM or FM (or  
RECEIVER).  
To control the AV receiver, press RECEIVERto select  
Receiver mode.  
You can also use the remote controller to control  
Onkyo Blu-ray Disc/DVD player, CD player, and  
other components.  
Remote Controller  
Controlling the AV Receiver  
a q/wbuttons (25)  
b D.TUN button (25)  
c DISPLAY button  
d CH +/– button (26)  
e Number buttons (25)  
See “Entering Remote Control Codes” for more  
details (page 50).  
ic  
a
b
For detailed information, see the pages in parentheses.  
a 8button (20)  
b REMOTE MODE/INPUT SELECTOR buttons (21)  
c TONE and Level buttons (46)  
d SP A/B button (33)  
j
c
k
e q/w/e/rand ENTER buttons  
d
f SETUP button (37)  
d
ae  
f
g Listening Mode buttons (28)  
h DIMMER button (34)  
l
m
i DISPLAY button (34)  
j MUTING button (35)  
k VOL q/wbutton (21)  
l RETURN button  
m HOME button (33)  
g
n SLEEP button (34)  
e
bh  
n
En-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Connections  
Connecting the AV  
Receiver  
Passive  
Subwoofer  
Surround  
right  
Surround  
left  
Connecting Your Speakers  
Connecting the Speaker Cables  
The following illustration shows how to connect the  
speakers to each pair of terminals.  
Using a Passive Subwoofer  
Corner  
position  
1/3 of wall  
position  
To find the best position for your subwoofer, while playing  
a movie or some music with good bass, experiment by  
placing your subwoofer at various positions within the  
room, and choose the one that provides the most satisfying  
results.  
Front B right  
Front B left  
Front A right  
Center  
Front A left  
Speakers B  
Speakers A  
Push-type speaker terminals  
Strip 3/8" to 1/2" (10 to 12 mm) of insulation from the ends  
of the speaker cables, and twist the bare wires tightly, as  
shown (Supplied speaker cables are already stripped).  
3/8" to 1/2" (10 to 12 mm)  
En-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Connections  
Speaker Configuration  
Connecting the Speaker Cables  
The following table indicates the channels you should use  
depending on the number of speakers that you have.  
No matter how many speakers you use, a passive  
subwoofer is recommended for a really powerful and solid  
bass.  
The speaker terminals are color-coded for identification  
purpose.  
Speaker  
Color  
White  
Red  
Front left  
Front right  
Center  
To get the best from your surround sound system, you need  
to set the speaker settings manually (page 40).  
Green  
Blue  
Surround left  
Surround right  
Subwoofer  
Number of speakers  
Front speakers  
2
3
4
5
Gray  
Purple  
Center speaker  
Surround speakers  
En-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Connections  
• Don’t connect more than one cable to each speaker  
terminal. Doing so may damage the AV receiver.  
• Don’t connect one speaker to several terminals.  
Speaker Connection Precautions  
Read the following before connecting your speakers:  
• You can connect speakers with an impedance of between  
6 and 16 ohms. If you use speakers with a lower  
impedance, and use the amplifier at high volume levels  
for a long period of time, the built-in amp protection  
circuit may be activated.  
• Disconnect the power cord from the wall outlet before  
making any connections.  
• Read the instructions supplied with your speakers.  
• Pay close attention to speaker wiring polarity. In other  
words, connect positive (+) terminals only to positive (+)  
terminals, and negative (–) terminals only to negative (–)  
terminals. If you get them the wrong way around, the  
sound will be out of phase and will sound unnatural.  
• Unnecessarily long, or very thin speaker cables may  
affect the sound quality and should be avoided.  
• Be careful not to short the positive and negative wires.  
Doing so may damage the AV receiver.  
• Make sure the metal core of the wire does not have  
contact with the AV receiver’s rear panel. Doing so may  
damage the AV receiver.  
En-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Connections  
Optical digital audio  
Optical digital connections allow you to enjoy digital  
AV Cables and Jacks  
About AV Connections  
Connecting AV components  
HDMI cable  
*1  
sound such as PCM , Dolby Digital or DTS. The audio  
HDMI  
quality is the same as coaxial.  
HDMI connections can carry digital video and audio.  
: Video & Audio  
TV, projector, etc.  
Component video  
Coaxial digital audio  
Coaxial digital connections allow you to enjoy digital  
AV receiver  
Component video separates the luminance (Y) and color  
difference signals (PB, PR), providing the best picture  
quality (some TV manufacturers label their component  
video sockets slightly differently).  
*1  
sound such as PCM , Dolby Digital or DTS. The audio  
quality is the same as optical.  
Orange  
Green  
Blue  
Red  
Y
Blu-ray Disc/  
DVD player  
PB  
PR  
Analog audio (RCA)  
Game console  
Analog audio connections (RCA) carry analog audio.  
Other cables  
: Video  
: Audio  
White  
Red  
Composite video  
Composite video is commonly used on TVs, VCRs, and  
other video equipment.  
TV, projector, etc.  
AV receiver  
*1  
Available sampling rate for PCM input signal (stereo/mono) is  
Yellow  
32/44.1/48/88.2/96 kHz. In case of an HDMI connection,  
176.4/192 kHz is also available.  
Note  
• The AV receiver does not support SCART plugs.  
• The AV receiver’s optical digital jacks have shutter-type covers  
that open when an optical plug is inserted and close when it’s  
removed. Push plugs in all the way.  
Blu-ray Disc/  
DVD player  
Game console  
Caution  
• Before making any AV connections, read the manuals  
supplied with your AV components.  
• Don’t connect the power cord until you’ve completed and  
double-checked all AV connections.  
• To prevent shutter damage, hold the optical plug straight  
when inserting and removing.  
• Push plugs in all the way to make  
good connections (loose connections  
can cause noise or malfunctions).  
• To prevent interference, keep audio  
and video cables away from power  
cords and speaker cables.  
Right!  
Wrong!  
En-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Connections  
Connecting Components with HDMI  
VCR or DVD recorder/digital video recorder  
Game console  
TV, projector, etc.  
Satellite/cable set-top box, etc.  
Blu-ray Disc/DVD player  
*
*
If your TV doesn’t support Audio Return Channel (ARC), you  
need to connect an optical digital cable together with the HDMI  
cable to the AV receiver.  
When listening to an HDMI component through the AV  
receiver, set the HDMI component so that its video can be seen  
on the TV screen (on the TV, select the input of the HDMI  
component connected to the AV receiver). If the TV power is off  
or the TV is set to another input source, this may result in no  
sound from the AV receiver or the sound may be cut off.  
See also:  
Audio Return Channel (ARC) function  
• “Connection Tips and Video Signal Path” (page 59)  
• “Using an RIHD-compatible TV, Player, or Recorder”  
(page 60)  
Audio Return Channel (ARC) function enables an HDMI  
capable TV to send the audio stream to the HDMI OUT of  
the AV receiver.  
• This function can be used when:  
– Your TV is ARC capable, and  
– The TV/CD input selector is selected, and  
– “HDMI Ctrl (RIHD)” is set to “On” (page 45), and  
– “Audio Return Ch (ARC)” is set to “Auto” (page 46).  
• “About HDMI” (page 62)  
Tip  
• To listen to the audio of a component connected via HDMI  
through your TV’s speakers, enable “HDMI Through”  
(page 45) and set the AV receiver to standby mode.  
Connect your components to the appropriate jacks. The  
default input assignments are shown below.  
Note  
: Assignment can be changed (page 39).  
• In the case of Blu-ray Disc/DVD players, if no sound is output  
despite following the above-mentioned procedure, set your Blu-  
ray Disc/DVD player’s HDMI audio settings to PCM.  
Jack  
Components  
HDMI IN1  
HDMI IN2  
HDMI IN3  
HDMI IN4  
Blu-ray Disc/DVD player  
VCR or DVD recorder/digital video recorder  
Satellite/cable set-top box, etc.  
Game console  
HDMI OUT TV, projector, etc.  
En-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Connections  
Note  
The on-screen menus appear only on a TV that is  
connected to the HDMI OUT. If your TV is connected  
to other video outputs, use the AV receiver’s display  
when changing settings.  
Connecting Your Components  
A B C  
*1  
*2  
*3  
When USB input is selected, you can input video signals from  
the AUX INPUT VIDEO jack. Video signals input from AUX  
INPUT VIDEO will be output from the MONITOR OUT jack.  
Do not connect the AV receiver’s USB port to a USB port on  
your computer. Music on your computer cannot be played  
through the AV receiver in this way.  
Connect a turntable (MM) that has a phono preamp built-in. If  
your turntable (MM) doesn’t have it, you’ll need a  
commercially available phono preamp.  
: Assignment can be changed (pages 39, 40).  
No. Jack/Port  
Components  
AUX INPUT  
VIDEO  
A
Camcorder, etc.  
If your turntable has a moving coil (MC) type cartridge, you’ll  
need a commercially available MC head amp or MC  
transformer as well as a phono preamp. See your turntable’s  
manual for details.  
AUDIO L/R  
USB, AUX INPUT  
VIDEO  
iPod/iPhone (video  
playback)  
B
C
D
*1  
*2  
USB  
iPod/iPhone, MP3 player,  
USB flash drive  
• With connection D, you can enjoy Dolby Digital and  
DTS.  
DIGITAL IN  
• With connection F, if your Blu-ray Disc/DVD player has  
both the main stereo and multichannel outputs, be sure to  
connect to the main stereo.  
OPTICAL 1 (GAME)  
OPTICAL 2 (TV/CD)  
COAXIAL (BD/DVD)  
COMPONENT VIDEO  
IN 1 (BD/DVD)  
Game console  
TV, CD player  
D E  
F
Blu-ray Disc/DVD player  
How to record a video source  
E
F
With the connections described above, you cannot record  
the videos through the AV receiver. See “Recording” about  
connections for video recording (page 36).  
Blu-ray Disc/DVD player,  
RI dock  
IN 2 (CBL/SAT)  
Satellite/cable set-top box,  
RI dock, etc.  
OUT  
TV, projector, etc.  
MONITOR OUT  
BD/DVD IN  
VCR/DVR IN  
TV, projector, etc.  
Blu-ray Disc/DVD player  
VCR, DVD recorder/  
digital video recorder, RI  
dock  
CBL/SAT IN  
Satellite/cable set-top box,  
etc.  
Connect your components to the appropriate jacks. The  
default input assignments are shown below.  
See “Connection Tips and Video Signal Path” for more  
information (page 59).  
GAME IN  
TV/CD IN  
Game console, RI dock  
TV, CD player, cassette  
tape deck, MD, CD-R,  
*3  
Turntable , RI dock  
En-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Connections  
Connecting a Recording Component  
Connecting Onkyo uComponents  
See “Recording” for details on recording (page 36).  
Make sure that each Onkyo component is  
connected with an analog audio cable (connection  
F in the hookup examples) (page 17).  
1
Make the uconnection (see the illustration).  
2
3
If you’re using an RI Dock or cassette tape deck,  
change the Input Display (page 35).  
With u(Remote Interactive), you can use the following  
R
L
ANALOG  
AUDIO OUT  
L
R
special functions:  
e.g., cassette tape deck  
RI Dock  
AUDIO  
IN  
VIDEO  
IN  
System On/Auto Power On  
VCR, DVD recorder,  
cassette tape deck,  
CDR, MD recorder, etc.  
When you start playback on a component connected via  
uwhile the AV receiver is on standby, the AV  
receiver will automatically turn on and select that  
component as the input source.  
R
L
ANALOG  
AUDIO OUT  
Direct Change  
Note  
Note  
When playback is started on a component connected via  
u, the AV receiver automatically selects that  
component as the input source.  
You can use the AV receiver’s remote controller to  
control your other u-capable Onkyo components,  
pointing the remote controller at the AV receiver’s  
remote control sensor instead of the component. You  
must enter the appropriate remote control code first  
(page 50).  
• The AV receiver must be turned on for recording. Recording is  
not possible while it’s in standby mode.  
• Use only ucables for uconnections. ucables are supplied  
with Onkyo components.  
• If you want to record directly from your TV or playback VCR to  
the recording VCR without going through the AV receiver,  
connect the TV/VCR’s audio and video outputs directly to the  
recording VCR’s audio and video inputs. See the manuals  
supplied with your TV and VCR for details.  
• Video signals connected to composite video inputs can be  
recorded only via composite video outputs. For example, if your  
TV/VCR is connected to a composite video input, the recording  
VCR must be connected to a composite video output.  
• The surround sound and DSP listening modes cannot be recorded.  
• Copy-protected Blu-ray Discs and DVDs cannot be recorded.  
• Sources connected to a digital input cannot be recorded. Only  
analog inputs can be recorded.  
• Some components have two ujacks. You can connect either  
one to the AV receiver. The other jack is for connecting  
additional u-capable components.  
Remote Control  
• Connect only Onkyo components to ujacks. Connecting other  
manufacturer’s components may cause a malfunction.  
• Some components may not support all ufunctions. Refer to the  
manuals supplied with your other Onkyo components.  
• DTS signals will be recorded as noise, so don’t attempt analog  
recording of DTS CDs or LDs.  
En-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Connections  
Connecting the Antennas  
Connecting the Power Cord  
This section explains how to connect the supplied indoor FM antenna and AM loop antenna.  
The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use  
the tuner.  
(Brazilian models)  
Connect the supplied power cord to the AV  
receiver’s AC INLET.  
1
North American and  
Brazilian models  
Asian models  
To AC wall outlet  
Insert the plug fully  
into the jack.  
Insert the plug fully  
into the jack.  
Push.  
Insert wire.  
Release.  
Plug the power cord into an AC wall outlet.  
Assembling the AM loop antenna  
Caution  
Note  
• Be careful not to injure yourself when  
using thumbtacks.  
• Before connecting the power cord, connect all of your  
speakers and AV components.  
• Turning on the AV receiver may cause a momentary power surge  
that might interfere with other electrical equipment on the same  
circuit. If this is a problem, plug the AV receiver into a different  
branch circuit.  
Thumbtacks, etc.  
• Do not use a power cord other than the one supplied with the AV  
receiver. The supplied power cord is designed exclusively for use  
with the AV receiver and should not be used with any other  
equipment.  
AM loop antenna (supplied)  
Indoor FM antenna (supplied)  
• Never disconnect the power cord from the AV receiver while the  
other end is still plugged into a wall outlet. Doing so may cause  
an electric shock. Always disconnect the power cord from the  
wall outlet first, and then the AV receiver.  
Note  
• Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible  
reception.  
• Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.  
Tip  
• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.  
• If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM  
antenna.  
En-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Turning On & Basic Operations  
Turning On  
Turning Off  
Turning On/Off the AV  
Receiver  
8ON/STANDBY  
Press 8ON/STANDBY on the front panel.  
Press 8ON/STANDBY on the front panel.  
1
1
or  
or  
Press RECEIVER followed by 8on the remote  
controller.  
Press RECEIVER followed by 8on the remote  
controller.  
The AV receiver comes on, and its display lights.  
The AV receiver will enter standby mode. To prevent  
any loud surprises when you turn on the AV receiver,  
always turn down the volume before you turn it off.  
Tip  
• For details on power management settings, see “Auto Standby”  
(page 44).  
8
RECEIVER  
En-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Turning On & Basic Operations  
Operating on the AV receiver  
Playing the Connected Component  
Playback  
Input selector buttons  
LISTENING MODE MASTER VOLUME  
Operating with the remote controller  
The on-screen menus appear only on a TV that is  
connected to the HDMI OUT. If your TV is connected  
to other video outputs, use the AV receiver’s display  
when changing settings.  
INPUT SELECTOR  
RECEIVER  
VOL q/w  
This section describes the procedure for using the  
remote controller unless otherwise specified.  
Use the input selector buttons to select the input  
source.  
1
Start playback on the source component.  
3
Listening mode buttons  
To adjust the volume, use the MASTER VOLUME  
control.  
Press RECEIVER followed by an INPUT  
1
SELECTOR button.  
Select a listening mode and enjoy!  
4
Start playback on the source component.  
See also:  
2
• “Playing an iPod/iPhone via USB” (page 23)  
• “Playing a USB Device” (page 24)  
• “Listening to AM/FM Radio” (page 25)  
• “iPod/iPhone Playback via Onkyo Dock”  
(page 48)  
• “Controlling Other Onkyo Components”  
(page 50)  
To adjust the volume, use VOL q/w.  
3
4
Select a listening mode and enjoy!  
See also:  
• “Using the Listening Modes” (page 28)  
En-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Turning On & Basic Operations  
TOP MENU  
RANDOM  
This button performs random playback.  
a
b
o
p
Controlling Contents of USB Devices  
This button displays the top menu for each media or service.  
REPEAT  
q/wand ENTER  
Press this button repeatedly to cycle through the repeat  
modes.  
These buttons navigate through the menus.  
h
e/r  
This button cycles through pages.  
Tip  
PLAYLIST e/r  
See “Controlling Other Onkyo Components” about the operation  
of other components (page 50).  
In Standard Mode (iPod/iPhone), this button selects  
playlists.  
PressUSB  
first.  
Note  
c
d
1
• The buttons you can use will differ depending on the devices and  
media used for playback.  
This button starts playback.  
i
7
This button selects the beginning of the current song.  
Pressing this button twice selects the previous song.  
a
e
f
g
5
b
j
c
This button fast-reverses the current song.  
3
This button pauses playback.  
d
e
f
k
l
m
SEARCH  
You can toggle between the playback screen and the list  
screen during playback.  
DISPLAY  
This button switches between song information.  
h
i
j
k
n
o
p
g
CH +/–  
In Standard Mode (iPod/iPhone), this button selects albums.  
RETURN  
This button returns to the previous menu.  
6
This button selects the next song.  
l
m
n
4
This button fast-forwards the current song.  
2
This button stops playback.  
MODE  
You can switch between Extended Mode and Standard Mode  
during iPod/iPhone playback.  
En-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Turning On & Basic Operations  
Use q/wto select a music file, and press ENTER or  
Understanding Icons on the Display  
Playing an iPod/iPhone via USB  
4
1to start playback.  
This section describes icons that appear on the AV  
receiver’s display during media playback.  
The on-screen menus appear only on a TV that is  
connected to the HDMI OUT.  
Note  
Icon  
Description  
• While the message “Connecting...” appears on the AV receiver’s  
display, do not disconnect the USB cable supplied with your  
iPod/iPhone or the USB device from the USB port.  
If you connect an iPod or iPhone to the USB port, no sound will  
be output from the headphones jack.  
This section explains how to play music files on the  
iPod/iPhone.  
Compatible iPod/iPhone models  
Folder  
Track  
Made for:  
Playback  
iPod touch (1st, 2nd, 3rd and 4th generation), iPod classic,  
iPod nano (2nd, 3rd, 4th, 5th and 6th generation),  
iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G, iPhone  
Extended Mode Control  
Pause  
The content information is displayed (lists are displayed),  
and you can control the content while looking at the screen.  
Playlists, Artists, Albums, Genres, Songs, Composers,  
Shuffle Songs, Now Playing.  
Press USB to select the “USB” input.  
Fast Forward  
Fast Reverse  
Artist  
1
2
Connect the USB cable that comes with the  
iPod/iPhone to the USB port on the front of the AV  
receiver.  
Standard Mode Control  
While reading the contents of your iPod/iPhone, the  
message “Connecting...” appears on the AV  
receiver’s display.  
The content information is not displayed, but can be  
operated using the iPod/iPhone or the remote controller.  
Album  
A list of your iPod/iPhone model’s contents appears  
(Extended Mode).  
Repeat One Track  
Repeat Folder (USB Device)  
Repeat  
Use q/wto select a folder, and then press ENTER to  
3
open it.  
Tip  
• If you want to operate using the iPod/iPhone or the remote  
controller, press MODE to switch to Standard mode.  
• When you disconnect the iPod/iPhone, the AV receiver  
remembers the current mode. This means that if you  
disconnect when in Extended Mode, the AV receiver will  
start in Extended Mode the next time you connect the  
iPod/iPhone.  
Shuffle  
Shuffle Album (iPod/iPhone)  
• You can also use the q/w, ENTER and TUNING MODE  
buttons on the front panel. TUNING MODE allows you to  
switch modes.  
• When connecting your iPod/iPhone with a USB cable, we  
recommend you use an official USB cable from Apple Inc.  
En-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Turning On & Basic Operations  
Playing a USB Device  
The on-screen menus appear only on a TV that is  
connected to the HDMI OUT.  
This section explains how to play music files from a USB  
device (e.g., USB flash drives and MP3 players).  
See also:  
• “USB Features” (page 63).  
Press USB to select the “USB” input.  
1
2
Plug your USB device into the AV receiver’s USB  
port.  
While reading the contents of your USB device, the  
message “Connecting...” appears on the AV  
receiver’s display.  
Press ENTER.  
A list of the device’s contents appears. To open a  
3
folder, use q/wto select it, and then press ENTER.  
Use q/wto select a music file, and press ENTER or  
4
1to start playback.  
Note  
• While the message “Connecting...” appears on the AV receiver’s  
display, do not disconnect the USB cable supplied with your  
iPod/iPhone or the USB device from the USB port.  
En-24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Turning On & Basic Operations  
Manual tuning mode  
Tuning into Radio Stations  
Listening to AM/FM Radio  
In manual tuning mode, FM stations will be in mono.  
Auto tuning mode  
This section describes the procedure using the buttons  
on the front panel unless otherwise specified.  
Press TUNING MODE so that the AUTO indicator  
goes off on the AV receiver’s display.  
1
Press TUNING MODE so that the AUTO indicator  
lights on the AV receiver’s display.  
1
Press and hold TUNING q/w.  
2
Using the Tuner  
Press TUNING q/w.  
The frequency stops changing when you release the  
button.  
2
With the built-in tuner you can enjoy AM and FM radio  
stations. You can store your favorite stations as presets for  
quick selection.  
Searching stops when a station is found.  
Press the buttons repeatedly to change the frequency  
one step at a time.  
When tuned into a station, the TUNED indicator  
lights. When tuned into a stereo FM station, the FM  
STEREO indicator lights as shown.  
You can also change the frequency steps (page 44).  
Tuning into stations by frequency  
You can tune into AM and FM stations directly by entering  
the appropriate frequency.  
FM STEREO  
Press AM or FM to select either “AM” or “FM”.  
In this example, FM has been selected.  
1
Band  
Frequency  
On the remote controller, press AM or FM to select  
“AM” or “FM”, followed by D.TUN.  
1
AUTO  
TUNED  
Tip  
(Actual display depends on the country.)  
• Tuning into weak FM stereo stations  
If the signal from a stereo FM station is weak, it may be  
impossible to get good reception. In this case, switch to  
manual tuning mode and listen to the station in mono.  
(Actual display depends on the country.)  
Within 8 seconds, use the number buttons to enter  
2
the frequency of the radio station.  
For example, to tune to 87.5 (FM), press 8, 7, 5.  
If you have entered the wrong number, you can retry  
after 8 seconds.  
En-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Turning On & Basic Operations  
Selecting Presets  
Presetting AM/FM Stations  
Using RDS (excluding North American and  
Brazilian models)  
You can store a combination of up to 40 of your favorite  
AM/FM radio stations as presets.  
To select a preset, use PRESET e/ron the AV  
1
receiver, or the remote controller’s CH +/–.  
RDS works only in areas where RDS broadcasts are  
available.  
Tip  
Tune into the AM/FM station that you want to store  
as a preset.  
1
• You can also use the remote controller’s number buttons to  
select a preset directly.  
See the previous section.  
When tuned into an RDS station, the RDS indicator lights.  
When the station is broadcasting text information, the text  
can be displayed.  
Press MEMORY.  
The preset number flashes.  
2
Deleting Presets  
What is RDS?  
Select the preset that you want to delete.  
RDS stands for Radio Data System and is a method of  
transmitting data in FM radio signals. It was developed by  
the European Broadcasting Union (EBU) and is available  
in most European countries. Many FM stations use it these  
days. In addition to displaying text information, RDS can  
also help you find radio stations by type (e.g., news, sport,  
rock, etc.).  
1
See the previous section.  
(Actual display depends on the country.)  
While holding down MEMORY, press TUNING  
MODE.  
The preset is deleted and its number disappears from  
the AV receiver’s display.  
2
While the preset number is flashing (about 8  
3
seconds), use PRESET e/rto select a preset from  
1 through 40.  
Press MEMORY again to store the station or  
4
channel.  
The AV receiver supports four types of RDS information:  
PS (Program Service)  
When tuned to an RDS station that’s broadcasting PS  
information, the station’s name will be displayed. Pressing  
DISPLAY will display the frequency for 3 seconds.  
RT (Radio Text)  
The station or channel is stored and the preset number  
stops flashing.  
Repeat this procedure for all of your favorite AM/FM  
radio stations.  
When tuned to an RDS station that’s broadcasting text  
information, the text will be shown on the AV receiver’s  
display as described in the next section.  
PTY (Program Type)  
This allows you to search for RDS radio stations by type  
(page 27).  
TP (Traffic Program)  
This allows you to search for RDS radio stations that  
broadcast traffic information (page 27).  
To be continued  
En-26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Turning On & Basic Operations  
RDS program types (PTY)  
Listening to Traffic News (TP)  
Note  
Type  
Display  
None  
• In some cases, the text characters displayed on the AV receiver  
may not be identical to those broadcast by the radio station. Also,  
unexpected characters may be displayed when unsupported  
characters are received. This is not a malfunction.  
• If the signal from an RDS station is weak, RDS data may be  
displayed intermittently or not at all.  
You can search for stations that broadcast traffic news.  
None  
News reports  
Current affairs  
Information  
Sport  
News  
Press RT/PTY/TP three times.  
1
Affairs  
Info  
If the current radio station is broadcasting TP (Traffic  
Program), “[TP]” will appear on the AV receiver’s  
display. If “TP” without square brackets appears, this  
means that the station is not broadcasting TP.  
Sport  
Displaying Radio Text (RT)  
Education  
Educate  
Drama  
Culture  
Science  
Varied  
Pop M  
Rock M  
Easy M  
Light M  
Classics  
Other M  
Weather  
Finance  
Children  
Social  
Drama  
To locate a station that is broadcasting TP, press  
ENTER.  
Press RT/PTY/TP once.  
The RT information scrolls across the AV receiver’s  
display.  
2
1
Culture  
The AV receiver searches until it finds a station that’s  
broadcasting TP.  
If no stations are found, the message “Not Found”  
appears.  
Science and technology  
Varied  
Note  
Pop music  
• The message “Waiting” may appear while the AV receiver  
waits for the RT information.  
• If the message “No Text Data” appears, no RT information  
is available.  
Rock music  
Middle of the road music  
Light classics  
Serious classics  
Other music  
Weather  
Finding Stations by Type (PTY)  
Finance  
You can search for radio stations by type.  
Children’s programmes  
Social affairs  
Religion  
Press RT/PTY/TP twice.  
The current program type appears on the AV  
receiver’s display.  
1
Religion  
Phone In  
Travel  
Phone in  
Travel  
Use PRESET e/rto select the type of program  
2
Leisure  
Leisure  
Jazz  
you want.  
See the table shown later in this chapter.  
Jazz music  
Country music  
National music  
Oldies music  
Folk music  
Documentary  
Alarm test  
Country  
Nation M  
Oldies  
To start the search, press ENTER.  
3
The AV receiver searches until it finds a station of the  
type you specified, at which point it stops briefly  
before continuing with the search.  
Folk M  
Document  
TEST  
When a station you want to listen to is found, press  
ENTER.  
4
Alarm  
Alarm!  
If no stations are found, the message “Not Found”  
appears.  
En-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Turning On & Basic Operations  
MOVIE/TV button  
This button selects the listening modes intended for use  
with movies and TV.  
Using Basic Functions  
Using the Listening Modes  
MUSIC button  
This button selects the listening modes intended for use  
with music.  
Selecting Listening Modes  
GAME button  
See “About Listening Modes” for detailed information  
This button selects the listening modes intended for use  
with video games.  
STEREO button  
about the listening modes (page 29).  
Listening Mode Buttons  
This button selects the Stereo listening mode and All  
Channel Stereo listening mode.  
Press RECEIVER first.  
• The Dolby Digital and DTS listening modes can only be  
selected if your Blu-ray Disc/DVD player is connected to  
the AV receiver with a digital audio connection (coaxial,  
optical, or HDMI).  
• The listening modes you can select depends on the format  
of the input signal. To check the format, see “Displaying  
Source Information” (page 34).  
MOVIE/TV, MUSIC, GAME  
• While a pair of headphones is connected, you can select the  
following listening modes: Direct, Stereo, and Mono.  
• While Speakers A and B are on, you can select only the  
Direct, Stereo, Mono, or T-D (Theater-Dimensional)  
listening mode.  
MUSIC  
GAME  
MOVIE/TV  
STEREO  
En-28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Turning On & Basic Operations  
Input Source  
Speaker Layout  
About Listening Modes  
The following audio formats are supported by the listening  
mode.  
The illustration shows which speakers are activated in each  
channel. See “Sp Config (Speaker Configuration)” for the  
speaker setup (page 40).  
The AV receiver’s listening modes can transform your  
listening room into a movie theater or concert hall, with  
high fidelity and stunning surround sound.  
This is mono (monophonic) sound.  
A
C
This is stereo (stereophonic) sound. Two  
independent audio signal channels are reproduced  
through two speakers.  
S
Explanatory Notes  
b
a
This is 5.1-channel surround sound. This surround  
system has five main channels of sound and a sixth  
subwoofer channel (called the point-one channel).  
D
*1 This is 7.1-channel surround sound. This is a further  
F
sound enhancement to 5.1-channel sound with two  
additional speakers that provide greater sound  
envelopment and more accurate positioning of  
sounds.  
*1  
The AV receiver outputs this source in 5.1-channel surround  
sound.  
c
d
a Front speakers  
b Center speaker  
c Surround speakers  
d Subwoofer  
En-29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Turning On & Basic Operations  
Onkyo-Original DSP Listening Modes  
Listening Mode  
Description  
Input  
Source  
Speaker  
Layout  
Listening Mode  
Description  
Input  
Source  
Speaker  
Layout  
T-D (Theater-  
Dimensional)*1  
With this mode you can enjoy a virtual  
surround sound even with only two or three  
speakers. This works by controlling how  
sounds reach the listener’s left and right ears.  
Good results may not be possible if there’s  
too much reverb, so we recommend that you  
use this mode in an environment with little  
or no natural reverb.  
A
S
D
F
ZXC  
Orchestra*1  
Suitable for classical or operatic music, this  
mode emphasizes the surround channels in  
order to widen the stereo image, and  
simulates the natural reverberation of a large  
hall.  
A
S
D
F
C
T
D
O r c h e s t r a  
Unplugged*1  
Suitable for acoustic instruments, vocals,  
and jazz, this mode emphasizes the front  
stereo image, giving the impression of being  
right in front of the stage.  
U n p l u g g e d  
Studio-Mix*1  
Suitable for rock or pop music, listening to  
music in this mode creates a lively sound  
field with a powerful acoustic image, like  
being at a club or rock concert.  
S t u d i o M i x  
TV Logic*1  
This mode adds realistic acoustics to TV  
shows produced in a TV studio, surround  
effects to the entire sound, and clarity to  
voices.  
T V L o g i c  
Game-RPG*1  
G a m e R P G  
In this mode, the sound has a dramatic feel  
with a similar atmosphere to Orchestra  
mode.  
Game-Action*1  
In this mode, sound localization is distinct  
with emphasis on bass.  
G a m e A c t i o n  
Game-Rock*1  
In this mode, sound pressure is emphasized  
to heighten live feel.  
G a m e R o c k  
Game-Sports*1  
In this mode, reverberation is increased and  
sound localization decreased slightly.  
G a m e S p o r t s  
All Ch Stereo  
Ideal for background music, this mode fills  
the entire listening area with stereo sound  
from the front and surround speakers.  
XC  
A l  
l
C h S t e r e o  
Full Mono  
In this mode, all speakers output the same  
sound in mono, so the sound you hear is the  
same regardless of where you are within the  
listening room.  
F u l  
l
M o n o  
En-30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Turning On & Basic Operations  
Listening Modes  
Listening Mode  
DSD*2  
Description  
Input  
Source  
Speaker  
Layout  
Listening Mode  
Description  
Input  
Source  
Speaker  
Layout  
In this mode, audio from the input source is  
output without surround-sound processing.  
The speaker configuration (presence of  
speakers), crossover frequency, speaker  
distance, A/V Sync and much of the  
processing set via Home menu are enabled.  
See “On-screen Setup” for more details  
(page 37).  
D
XC  
Direct  
In this mode, audio from the input source is  
output without surround-sound processing.  
The speaker configuration (presence of  
speakers) and speaker distance settings are  
enabled, but much of the processing set via  
Home menu is disabled. A/V Sync does not  
have effect on the analog audio. See “On-  
screen Setup” for more details  
A
S
D
F
ZXC  
D S D  
Dolby Digital  
D i r e c t  
D o l b y  
D
Dolby Digital Plus*3  
D
F
XC  
D o l b y  
D
+
Dolby TrueHD  
(page 37).  
D o l b y T r u e H D  
Stereo  
Sound is output from the front left and right  
speakers and subwoofer.  
DTS  
D
XC  
XC  
S t e r e o  
D T S  
Mono  
Use this mode when watching an old movie  
with a mono soundtrack, or use it with the  
foreign language soundtracks recorded in the  
left and right channels of some movies. It  
can also be used with DVDs or other sources  
containing multiplexed audio, such as  
karaoke DVDs.  
DTS-HD High  
Resolution Audio  
D
F
M o n o  
D T S H D H R  
DTS-HD Master  
Audio  
Multichannel  
This mode is for use with PCM multichannel  
sources.  
D
F
XC  
D T S H D MS T R  
DTS Express  
M u l  
t
i c h  
D
D
XC  
XC  
D T S E x p r e s s  
DTS 96/24  
This mode is for use with DTS 96/24  
sources. This is high-resolution DTS with a  
96 kHz sampling rate and 24-bit resolution,  
providing superior fidelity. Use it with  
DVDs that bear the DTS 96/24 logo.  
D T S 9 6 / 2 4  
En-31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Turning On & Basic Operations  
Listening Mode  
Description  
Input  
Source  
Speaker  
Layout  
Note  
*1  
These listening modes cannot be selected during USB or iPod playback.  
Dolby Pro Logic II  
Dolby Pro Logic II expands any 2-channel  
source for 5.1-channel playback. It provides  
a very natural and seamless surround-sound  
experience that fully envelops the listener.  
As well as music and movies, video games  
can also benefit from the dramatic spatial  
effects and vivid imaging.  
*2  
The AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player  
side to PCM might obtain a better sound according to the player. In that case, set the output setting  
on the player side to PCM.  
*3  
For the Blu-ray Discs, Dolby Digital is used.  
• The listening modes cannot be selected with some source formats.  
• Dolby PLII Movie  
S
S
XC  
XC  
P L  
P L  
P L  
M o v i e  
M u s i c  
G a m e  
Use this mode with DVDs and videos that  
bear the Dolby Surround logo or TV shows  
that feature Dolby Surround. You can also  
use this mode with stereo movies or TV  
shows and the AV receiver will create a 5.1  
surround mix from the 2-channel stereo.  
• Dolby PLII Music  
Use this mode to add 5.1 surround to stereo  
sources such as music CDs and DVDs.  
• Dolby PLII Game  
Use this mode when playing game discs.  
Neo:6  
This mode expands any 2-channel source for  
up to 5.1-channel playback. It uses seven  
full-bandwidth channels of matrix decoding  
for matrix-encoded material, providing a  
very natural and seamless surround sound  
experience that fully envelops the listener.  
• Neo:6 Cinema  
Use this mode with any stereo movie (e.g.,  
TV, DVD, VHS).  
N e o : 6 C i n e m a  
N e o : 6 M u s i c  
• Neo:6 Music  
Use this mode with any stereo music source  
(e.g., CD, radio, cassette, TV, VHS, DVD).  
En-32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Turning On & Basic Operations  
*1  
Info  
Using the Home Menu  
Selecting Speakers A and B  
`You can view the information of the following  
The Home menu provides quick access to frequently used  
settings. You can change settings and view the current  
information.  
You can use two sets of front speakers with the AV  
receiver: Speakers A for up to 5.1-channel playback in  
your main listening room and Speakers B for 2-channel  
stereo playback in another room.  
items: “Input” and “Output”.  
*2  
Listening Mode  
`You can select the listening modes that are  
grouped in the following categories:  
The on-screen menus appear only on a TV that is  
connected to the HDMI OUT. If your TV is connected  
to other video outputs, use the AV receiver’s display  
when changing settings.  
MOVIE/TV”, “MUSIC” and “GAME”.  
Use q/wto select the category and e/rto  
select the listening mode. Press ENTER to  
switch to the selected listening mode.  
Press RECEIVER once followed by SP A/B  
repeatedly to cycle through the selection:  
Speakers A Speakers A&B Speakers B  
Off ←  
Speaker indicators and output channels are shown  
below.  
Note  
Note  
• The on-screen menus are displayed when:  
– There is no video input, or  
– The video input is 480p, 576p, 720p, 1080i, or 1080p.  
*1  
Depending on the input source and listening mode, not all  
channels shown here output the sound.  
• This setting is not available in either of the following cases:  
–The “Audio TV Out” setting is set to “On” (page 45).  
–“HDMI Ctrl (RIHD)” is set to “On” (page 45) and  
you’re listening through your TV speakers.  
Speaker indicators Output channel  
Speakers A: 5.1 channels  
*2  
A
Press RECEIVER followed by HOME.  
The Home menu will be superimposed on the TV  
screen.  
*3  
Speakers A: 2.1 channels  
Speakers B: 2 channels  
A
B
B
Speakers B: 2 channels  
Use q/wand ENTER to make the desired selection.  
2
No sound  
Input  
*3  
While Speakers B is on, channels are reduced to 2.1 in the  
main room.  
`You can select the input source.  
Use q/wto select the desired input source.  
Pressing ENTER switches to the selected input  
source.  
Tip  
• Alternatively, you can use the AV receiver’s SPEAKERS  
A and B.  
Audio  
`You can change the following settings: “Bass”,  
Treble”, “Subwoofer Level”, “Center Level”,  
EX.BASS”, “Late Night”, “Music Optimizer”,  
and “Cinema Filter”.  
See also:  
• “Using the Audio Settings” (page 46)  
En-33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Turning On & Basic Operations  
Using the Sleep Timer  
Setting the Display Brightness  
Displaying Source Information  
With the sleep timer, you can set the AV receiver to turn  
off automatically after a specified period.  
You can adjust the brightness of the AV receiver’s display.  
You can display various information about the current  
input source as follows.  
Press RECEIVER once followed by DIMMER  
repeatedly to switch between: normal, dim, or  
1
Press RECEIVER once followed by SLEEP  
Press RECEIVER once followed by DISPLAY  
repeatedly to cycle through the available  
information.  
1
1
repeatedly to select the required sleep time.  
The sleep time can be set from 90 to 10 minutes in 10  
minute steps.  
dimmer brightness.  
Tip  
Tip  
(North American and Brazilian models) Alternatively,  
you can use the AV receiver’s DIMMER.  
The SLEEP indicator lights on the AV receiver’s  
display when the sleep timer has been set. The  
specified sleep time appears for about 5 seconds, then  
the previous display reappears.  
• Alternatively, you can use the AV receiver’s DISPLAY.  
The following information can typically be displayed.  
Input source &  
volume*1  
Tip  
• If you need to cancel the sleep timer, press SLEEP  
repeatedly until the SLEEP indicator goes off.  
• To check the time remaining until the AV receiver sleeps,  
press SLEEP. Note that if you press again on SLEEP as  
the time being displayed is equal to 10 minutes or less, the  
sleep timer will go off.  
Listening mode  
Signal format*2  
or sampling  
frequency  
*1  
When AM or FM radio is used, the band, frequency, and preset  
number are displayed.  
*2  
If the input signal is digital, the signal format is displayed.  
Information is displayed for about three seconds, then the  
previously displayed information reappears.  
En-34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Turning On & Basic Operations  
Changing the Input Display  
Using the Music Optimizer  
Muting the AV Receiver  
The Music Optimizer function enhances the sound quality  
of compressed music files.  
You can temporarily mute the output of the AV receiver.  
When you connect an u-capable Onkyo component, you  
must configure the input display so that ucan work  
properly.  
Press RECEIVER followed by MUTING.  
The output is muted and the MUTING indicator  
1
Press MUSIC OPTIMIZER on the front panel.  
The M.Opt indicator lights on the AV receiver’s  
1
This setting can be done only from the front panel.  
flashes on the AV receiver’s display.  
display.  
Press TV/CD, GAME or VCR/DVR.  
TV/CD”, “GAME” or “VCR/DVR” appears on the  
Tip  
1
Tip  
• To unmute, press MUTING again or adjust the volume.  
• Muting is automatically cancelled when the AV receiver is  
set to standby.  
AV receiver’s display.  
• Alternatively, you can use the remote controller’s HOME.  
• See “Music Optimizer” for more details (page 47).  
Press and hold down the same button (about  
3 seconds) to change the input display.  
2
Repeat this step to select the desired input display.  
TV/CD:  
TAPE  
GAME:  
GAME DOCK  
VCR/DVR: VCR/DVR DOCK  
Note  
• “DOCK” can be selected for the “TV/CD”, “GAME” or  
VCR/DVR” input selector, but not at the same time.  
• Enter the appropriate remote control code before using the  
remote controller for the first time (page 50).  
En-35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Turning On & Basic Operations  
Using Headphones  
Recording  
This section explains how to record the selected input  
source to a component with recording capability.  
Connect a pair of stereo headphones with a  
standard plug (1/4 inch or 6.3 mm) to the PHONES  
1
jack.  
AV Recording  
Note  
Audio sources can be recorded to a recorder (e.g., cassette  
tape deck, CDR, MD recorder). Video sources can be  
recorded to a video recorder (e.g., VCR, DVD recorder).  
• Always turn down the volume before connecting your  
headphones.  
• While the headphones plug is inserted in the PHONES  
jack, the speakers are turned off.  
• When you connect a pair of headphones, the listening mode  
is set to Stereo, unless it’s already set to Stereo, Mono, or  
Direct.  
• If you connect an iPod or iPhone to the USB port on the AV  
receiver, no sound will be output from the headphones jack.  
Use the input selector buttons to select the source  
that you want to record.  
You can watch the source while recording. The AV  
receiver’s MASTER VOLUME control has no effect  
on recording.  
1
On your recorder, start recording.  
2
3
On the source component, start playback.  
If you select another input source during recording,  
that input source will be recorded.  
En-36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Advanced Operations  
Explanatory Notes  
Common Procedures in Setup Menu  
On-screen Setup  
Menu  
Sp Config  
The setup menus provides a convenient way to change the  
AV receiver’s various settings. Settings are organized into  
10 categories.  
a
Remote indicator  
Subwoofer  
`Yes  
b
c
`No  
The on-screen menus appear only on a TV that is  
connected to the HDMI OUT. If your TV is connected  
to other video outputs, use the AV receiver’s display  
when changing settings.  
RECEIVER  
b Setting target  
ENTER  
c Setting options (default setting underlined)  
q/w/e/r  
This section describes the procedure for using the  
remote controller unless otherwise specified.  
Menu  
SETUP  
RETURN  
1. HDMI Input  
2. Component  
3. Digital Audio  
4. Sp Config  
5. Sp Distance  
6. Level Cal  
BD/DVD  
VCR/DVR  
CBL/SAT  
GAME  
Note  
• The on-screen menus are displayed when:  
– There is no video input, or  
– The video input is 480p, 576p, 720p, 1080i, or 1080p.  
Press RECEIVER followed by SETUP.  
1
2
AUX  
TUNER  
TV/CD  
Use q/wto select a menu item, and then press  
7. Audio Adjust  
8. Source Setup  
9. Hardware  
ENTER.  
Use q/wto select a setting target, and use e/rto  
3
Setting target  
change the setting.  
10. HDMI Setup  
Press SETUP to close the menu.  
Press RETURN to return to the previous menu.  
Menu  
Note  
• This procedure can also be performed on the AV receiver by  
using SETUP, the cursor buttons, and ENTER.  
En-37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Advanced Operations  
Menu item  
Setting target  
Left  
Setup menu items  
Level Cal  
(page 41)  
Center  
Menu item  
Setting target  
Right  
HDMI Input  
(page 39)  
BD/DVD  
VCR/DVR  
CBL/SAT  
GAME  
Surround Right  
Surround Left  
Subwoofer  
Input Ch (Mux)  
Input Ch (Mono)  
Panorama  
Audio Adjust  
(page 42)  
AUX  
TV/CD  
Component  
(page 39)  
BD/DVD  
VCR/DVR  
CBL/SAT  
GAME  
Dimension  
Center Width  
Center Image  
Listening Angle  
A/V Sync  
AUX  
Source Setup  
(page 43)  
TV/CD  
Name  
Digital Audio  
(page 40)  
BD/DVD  
VCR/DVR  
CBL/SAT  
GAME  
Audio Selector  
Fixed Mode  
Volume OSD  
Remote ID  
Hardware  
(page 44)  
AUX  
AM/FM Freq Step  
AM Freq Step  
TV/CD  
Sp Config  
(page 40)  
Subwoofer  
Front  
Auto Standby  
HDMI Ctrl (RIHD)  
HDMI Through  
Audio TV Out  
Audio Return Ch  
LipSync  
HDMI Setup  
(page 45)  
Center  
Surround  
Crossover  
Double Bass  
Unit  
Sp Distance  
(page 41)  
Left  
Center  
Right  
Surround Right  
Surround Left  
Subwoofer  
En-38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Advanced Operations  
Note  
HDMI Input  
Component (Component Video Input)  
• If no video component is connected to HDMI output (even if the  
HDMI input is assigned), the AV receiver selects the video  
source based on the setting of “Component (Component Video  
Input)”.  
1
2
1
2
3
4
5
6
• When an HDMI IN is assigned to an input selector as explained  
here, the same HDMI IN will be set as a priority in the “Digital  
Audio (Digital Audio Input)” (page 40). In this case, if you  
want to use the coaxial or optical audio input, make the  
appropriate selection in the “Audio Selector” setting  
(page 43).  
• Do not assign an HDMI IN to the TV/CD selector while “HDMI  
Ctrl (RIHD)” is set to “On” (page 45), otherwise  
appropriate CEC (Consumer Electronics Control) operation will  
not be guaranteed.  
• If you assign “- - - - -” to an input selector that is currently  
selected in “HDMI Through” (page 45), the “HDMI  
Through” setting will be automatically switched to “Off”.  
• The “TUNER” selector cannot be assigned and is fixed at the  
- - - - -” option.  
Menu  
HDMI Input  
Menu  
Component  
If you connect a video component to an HDMI input, you  
must assign that input to an input selector. For example, if  
you must assign “HDMI2” to the “BD/DVD” input  
selector.  
If you connect a video component to a component video  
input, you must assign that input to an input selector. For  
example, if you connect your Blu-ray Disc/DVD player to  
COMPONENT VIDEO IN 2, you must assign “IN2” to  
the “BD/DVD” input selector.  
Here are the default assignments.  
Here are the default assignments.  
Input selector  
BD/DVD  
VCR/DVR  
CBL/SAT  
GAME  
Default assignment  
HDMI1  
Input selector  
BD/DVD  
VCR/DVR  
CBL/SAT  
GAME  
Default assignment  
IN1  
HDMI2  
- - - - -  
IN2  
HDMI3  
HDMI4  
- - - - -  
- - - - -  
- - - - -  
AUX  
- - - - -  
AUX  
TV/CD  
- - - - -  
TV/CD  
BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,  
TV/CD  
BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,  
TV/CD  
`HDMI1, HDMI2, HDMI3, HDMI4:  
Select the input to which the component has been  
connected.  
`IN1, IN2:  
Select the input to which the component has been  
connected.  
`- - - - -:  
`- - - - -:  
Select if you’re not using the HDMI OUT.  
Each HDMI input cannot be assigned to two input  
selectors or more. When HDMI1 - HDMI4 have already  
been assigned, you must first set any unused input  
selectors to “- - - - -” or you will be unable to assign  
HDMI1 - HDMI4 to input selector.  
Select if you’re not using the COMPONENT  
VIDEO OUT.  
Note  
• The “TUNER” selector cannot be assigned and is fixed at the  
- - - - -” option.  
En-39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Advanced Operations  
Front  
`Small:  
`Large:  
Digital Audio (Digital Audio Input)  
Sp Config (Speaker Configuration)  
1
2
3
4
5
6
1
2
3
4
5
6
Select based on the cone diameter.  
Note  
Menu  
Digital Audio  
Menu  
Sp Config  
• If the “Subwoofer” setting is set to “No”, this setting is fixed to  
Large”.  
If you connect a component to a digital audio input, you  
must assign that input to an input selector. For example, if  
you connect your CD player to the OPTICAL IN 1, you  
must assign “OPTICAL1” to the “TV/CD” input selector.  
Here are the default assignments.  
This section explains how to specify which speakers are  
connected and their sizes.  
*1  
*1  
Center , Surround  
`Small:  
`Large:  
Select based on the cone diameter.  
Cone diameter  
`None  
Input selector  
BD/DVD  
VCR/DVR  
CBL/SAT  
GAME  
Default assignment  
COAXIAL  
- - - - -  
Note  
*1  
If the “Front” setting is set to “Small”, the “Large” option  
cannot be selected.  
For speakers with a cone diameter larger than 6-1/2 inches  
(16 cm), specify Large (full band). For those with a  
smaller diameter, specify Small (default crossover  
120 Hz).  
The crossover frequency can be changed in the “Crossover  
(Crossover Frequency)”.  
- - - - -  
OPTICAL1  
- - - - -  
Crossover (Crossover Frequency)  
This setting is advantageous for the speakers that you  
specified as “Small” in the “Sp Config (Speaker  
Configuration)”. To get the best bass performance from  
your speaker system, you need to set the crossover  
frequency according to the size and frequency response  
of your speakers.  
`40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz,  
120Hz, 150Hz, 200Hz  
Use the diameter of the smallest speaker in your system  
when choosing the crossover frequency.  
AUX  
TV/CD  
OPTICAL2  
BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,  
TV/CD  
`COAXIAL, OPTICAL1, OPTICAL2:  
Select the input to which the component has been  
connected.  
Note  
• These settings are not available in either of the following cases:  
– A pair of headphones is connected.  
– The “Audio TV Out” setting is set to “On” (page 45).  
– “HDMI Ctrl (RIHD)” is set to “On” (page 45) and you’re  
listening through your TV speakers.  
`- - - - -:  
Select if the component is connected to an analog  
audio input.  
– Speakers B is on.  
– Speakers A is off.  
Speaker cone diameter  
Over 8 in. (20 cm)  
Crossover frequency  
Note  
Subwoofer  
`Yes  
`No  
*2  
40/50/60 Hz  
• When an HDMI IN is assigned to an input selector in  
HDMI Input” (page 39), the same HDMI IN will be set as  
a priority in this assignment. In this case, if you want to use the  
coaxial or optical audio input, make the appropriate selection in  
the “Audio Selector” (page 43).  
• Available sampling rates for PCM signals (stereo/mono) from a  
digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16,  
20, 24 bit.  
*2  
6-1/2 to 8 in. (16 to 20 cm)  
5-1/4 to 6-1/2 in. (13 to 16 cm)  
3-1/2 to 5-1/4 in. (9 to 13 cm)  
Under 3-1/2 in. (9 cm)  
70/80/90 Hz  
100 Hz  
120 Hz  
*2  
150/200 Hz  
*2  
Choose the setting suitable for the speaker.  
• The “TUNER” selector cannot be assigned and is fixed at the  
- - - - -” option.  
To be continued  
En-40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Advanced Operations  
Note  
Sp Distance (Speaker Distance)  
Level Cal (Level Calibration)  
• For a more accurate setting, look up the frequency response in the  
manuals supplied with your speakers and set accordingly.  
• Choose a higher crossover frequency if you want more sound  
from your subwoofer.  
1
2
3
4
5
6
1
2
3
4
5
6
Menu  
Sp Distance  
Menu  
Level Cal  
Double Bass  
`On  
`Off  
Here you can specify the distance from each speaker to the  
listening position so that the sound from each speaker  
arrives at the listener’s ears as the sound designer intended.  
Here you can adjust the level of each speaker with the  
built-in test tone so that the volume of each speaker is the  
same at the listening position.  
Turn this setting on to boost bass output by feeding bass  
sounds from the front left, right, and center channels to the  
subwoofer.  
Note  
Note  
• These settings are not available in either of the following cases:  
– A pair of headphones is connected.  
• These settings cannot be calibrated in either of the following  
cases:  
Note  
– The “Audio TV Out” setting is set to “On” (page 45).  
– “HDMI Ctrl (RIHD)” is set to “On” (page 45) and you’re  
listening through your TV speakers.  
– Speakers B is on.  
– Speakers A is off.  
– A pair of headphones is connected.  
– The “Audio TV Out” setting is set to “On” (page 45).  
– “HDMI Ctrl (RIHD)” is set to “On” (page 45) and you’re  
listening through your TV speakers.  
– Speakers B is on.  
• When the “Subwoofer” setting is set to “No” or the “Front”  
setting to “Small”, this setting is fixed to “Off” (page 40).  
• This setting is set to “On” automatically when the “Subwoofer”  
and “Front” settings are set for the first time to “Yes” and  
Large” respectively.  
– Speakers A is off.  
– The AV receiver is muted.  
Unit  
`feet:  
*1  
Left, Center , Right, Surround Right, Surround  
Left  
Distances can be set in feet. Range: 1ft to 30ft in  
1 foot steps.  
`meters:  
`–12 dB to 0 dB to +12 dB in 1 dB step.  
Distances can be set in meters. Range: 0.3m to 9.0m  
in 0.3 meter steps.  
(The default setting varies from country to country.)  
*1  
Subwoofer  
`–15 dB to 0 dB to +12 dB in 1 dB step.  
Note  
Left, Center, Right, Surround Right, Surround  
Left, Subwoofer  
`Specify the distance from the each speaker to your  
listening position.  
• Speakers that you set to “No” or “None” in the “Sp Config  
(Speaker Configuration)” (page 40) cannot be selected.  
*1  
For the center speaker and subwoofer, the level settings made  
by using the Home menu are saved in this menu (page 33).  
Tip  
Note  
• If you’re using a handheld sound level meter, adjust the level of  
each speaker so that it reads 75 dB SPL at the listening position,  
measured with C-weighting and slow reading.  
• Speakers that you set to “No” or “None” in the “Sp Config  
(Speaker Configuration)” (page 40) cannot be selected.  
En-41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Advanced Operations  
Dolby  
DTS  
Audio Adjust  
PL II Music (2ch Input)  
These settings apply to only 2-channel stereo sources.  
Neo:6 Music  
1
2
3
4
5
6
Center Image  
Panorama  
`On  
`Off  
`0 to 2 to 5  
Menu  
Audio Adjust  
With this setting, you can specify by how much the front  
left and right channel output is attenuated in order to create  
the center channel.  
Changing the value from “0” to “5” will spread the sound  
of the center channel to left and right (outwards).  
With the Audio Adjust functions and settings, you can  
adjust the sound and listening modes as you like.  
With this setting, you can broaden the width of the front  
stereo image when using the Dolby Pro Logic II Music  
listening mode.  
Multiplex/Mono  
Dimension  
`–3 to 0 to +3  
Theater-Dimensional  
Multiplex  
With this setting, you can move the sound field forward or  
backward when using the Dolby Pro Logic II Music  
listening mode. Higher settings move the sound field  
backward. Lower settings move it forward.  
If the stereo image feels too wide, or there’s too much  
surround sound, move the sound field forward to improve  
the balance. Conversely, if the stereo image feels like it’s  
in mono, or there’s not enough surround sound, move it  
backward.  
Input Ch (Mux)  
`Main  
`Sub  
`Main/Sub  
This setting determines which channel of a stereo  
multiplex source is output. Use it to select audio channels  
or languages with multiplex sources, multilingual TV  
broadcasts, and so on.  
`Wide:  
Select if the listening angle is 40 degrees.  
`Narrow:  
Select if the listening angle is 20 degrees.  
With this setting, you can optimize the Theater-  
Dimensional listening mode by specifying the angle of the  
front left and right speakers relative to the listening  
position. Ideally, the front left and right speakers should be  
equidistant from the listening position and at an angle close  
to one of the two available settings.  
Mono  
Center Width  
`0 to 3 to 7  
Input Ch (Mono)  
`Left + Right  
`Left  
`Right  
This setting specifies the channel to be used for playing  
any 2-channel digital source such as Dolby Digital, or 2-  
channel analog/PCM source in the Mono listening mode.  
With this setting, you can adjust the width of the sound  
from the center speaker when using the Dolby Pro Logic II  
Music listening mode. Normally, if you’re using a center  
speaker, the center channel sound is output from only the  
center speaker. (If you’re not using a center speaker, the  
center channel sound will be distributed to the front left  
and right speakers to create a phantom center). This setting  
controls the front left, right, and center mix, allowing you  
to adjust the weight of the center channel sound.  
Front left speaker  
Front right speaker  
20°/40°  
En-42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Advanced Operations  
Preset Name For Input Selector  
Audio Selector  
Source Setup  
Name  
Audio Selector  
`ARC:  
1
2
3
4
5
6
`- - -, Blu-ray, DVD, HD DVD, VCR, DVR, Tivo,  
CableSTB, SAT STB, PS3, Wii, Xbox, PC, TV, CD,  
TAPE, iPod:  
The audio signal from your TV tuner can be sent to  
the HDMI OUT of the AV receiver.  
Items can be set individually for each input selector.  
*1  
To reset to the default, select “- - -”.  
You can enter a preset name for each individual input  
selector for easy identification. When entered, the preset  
name will be displayed.  
With this selection, the TV’s audio can be  
automatically selected as a priority among other  
assignments.  
Preparation  
Press the input selector buttons to select an input source.  
`HDMI:  
This can be selected when HDMI IN has been  
assigned as an input source. If both HDMI (HDMI  
IN) and digital audio inputs (COAXIAL IN or  
OPTICAL IN) have been assigned, HDMI input is  
automatically selected as a priority.  
Menu  
Source Setup  
Note  
• You can’t assign the same preset name to multiple input selectors.  
• This setting cannot be used for the AM, FM or USB input  
selector.  
A/V Sync  
A/V Sync  
`COAXIAL:  
`0 ms to 400 ms in 10 msec steps  
This can be selected when COAXIAL IN has been  
assigned as an input source. If both coaxial and  
HDMI inputs have been assigned, coaxial input is  
automatically selected as a priority.  
When using progressive scanning on your Blu-ray  
Disc/DVD player, you may find that the picture and sound  
are out of sync. With this setting, you can correct this by  
delaying the audio signals.  
To view the TV picture while setting the delay, press  
ENTER.  
`OPTICAL:  
This can be selected when OPTICAL IN has been  
assigned as an input source. If both optical and HDMI  
inputs have been assigned, optical input is  
automatically selected as a priority.  
To return to the previous screen, press RETURN.  
The range of values you can adjust will depend on whether  
your TV supports HDMI Lip Sync and if the “LipSync”  
setting is set to “On” or not (page 46).  
`Analog:  
The AV receiver always outputs analog signals.  
You can set priorities of audio output when there are both  
digital and analog inputs.  
Note  
• A/V Sync is disabled when the Direct listening mode is used with  
an analog input source.  
Note  
• This setting can be made only for the input source that is assigned  
as HDMI IN, COAXIAL IN, or OPTICAL IN.  
*1  
You can select “ARC” if you select the TV/CD input selector.  
But you cannot if you’ve selected “Off” in the “Audio Return  
Ch” setting (page 46).  
En-43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Advanced Operations  
Setting the Incoming Digital Signal (Fixed  
Mode)  
Tuner  
Hardware  
AM/FM Freq Step (North American and Brazilian  
models)  
1
2
3
4
5
6
Fixed Mode  
`10kHz/200kHz:  
`Off:  
The format is detected automatically. If no digital  
input signal is present, the corresponding analog  
input is used instead.  
`9kHz/50kHz:  
Menu  
Hardware  
Select the frequency step according to your area.  
OSD  
AM Freq Step (Asian models)  
`10kHz:  
`9kHz:  
Select the frequency step according to your area.  
For AM/FM tuning to work properly, you must specify the  
AM/FM frequency step used in your area.  
`PCM:  
Volume OSD  
`On  
`Off  
Turn this setting on to display the volume level on the TV  
screen while it is adjusted.  
Only 2-channel PCM format input signals will be  
heard. If the input signal is not PCM, the PCM  
indicator will flash and noise may also be produced.  
`DTS:  
Only DTS (but not DTS-HD) format input signals  
will be heard. If the input signal is not DTS, the dts  
indicator will flash and there will be no sound.  
When “HDMI”, “COAXIAL” or “OPTICAL” is selected  
in the “Audio Selector” setting, you can then specify the  
signal type in “Fixed Mode”.  
Note  
Remote ID  
• When this setting is changed, all radio presets will be deleted.  
Remote ID  
`1, 2, or 3  
Auto Standby  
Normally, the AV receiver detects the signal format  
automatically. However, if you experience either of the  
following issues when playing PCM or DTS material, you  
can manually set the signal format to PCM or DTS.  
• If the beginnings of tracks from a PCM source are cut off,  
try setting the format to PCM.  
When several Onkyo components are used in the same  
room, their remote ID codes may overlap. To differentiate  
the AV receiver from the other components, you can  
change its remote ID from “1”, to “2” or “3”.  
Auto Standby  
`Off  
`On  
When “Auto Standby” is set to “On”, the AV receiver  
will automatically enter standby mode if there is no  
operation for 30 minutes with no audio and no video signal  
input.  
Auto Standby” will appear on the AV receiver’s display  
and OSD 30 seconds before the Auto Standby comes on.  
Default setting: On (Asian models), Off (North  
American and Brazilian models)  
Note  
• If you do change the AV receiver’s remote ID, be sure to change  
the remote controller to the same ID (see below), otherwise, you  
won’t be able to control it with the remote controller.  
• If noise is produced when fast forwarding or reversing a  
DTS CD, try setting the format to DTS.  
Note  
Changing the remote controller’s ID  
• The setting will be reset to “Off” when you change the setting in  
the “Audio Selector” (page 43).  
While holding down RECEIVER, press and hold  
down SETUP until the remote indicator lights  
1
Note  
(about 3 seconds).  
• Set to “On, the Auto Standby function may activate itself during  
playback with some sources.  
Use the number buttons to enter ID 1, 2, or 3.  
The remote indicator flashes twice.  
2
En-44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Advanced Operations  
Audio TV Out  
`Off  
`On  
This preference determines whether the incoming audio  
signal is output from the HDMI output. You may want to  
turn this preference on if your TV is connected to the  
HDMI output and you want to listen to the audio from a  
connected component through your TV’s speakers.  
Normally, this should be set to “Off”.  
• When the source equipment is connected with the u  
connection, it may malfunction if “HDMI Ctrl (RIHD)” is set to  
On”.  
HDMI Setup  
1
2
3
4
5
6
HDMI Through  
`Off  
Menu  
HDMI Setup  
`BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,  
TV/CD:  
Selects the input source for which the HDMI  
Through function is enabled.  
`Last:  
HDMI Ctrl (RIHD)  
`Off  
`On  
Note  
The HDMI Through function is activated on the input  
source selected at the time of setting the AV receiver  
to standby mode.  
• If “On” is selected and the audio can be output from the TV, the  
AV receiver will output no sound through its speakers. In this  
case, “TV Speaker” appears on the AV receiver’s display by  
pressing DISPLAY.  
• When HDMI Ctrl (RIHD)is set to On, this setting is fixed  
to Auto.  
Turn this setting on to allow p-compatible  
components connected via HDMI to be controlled by the  
AV receiver (page 60).  
When enabling the HDMI Through function, regardless of  
whether the AV receiver is on or in standby, both audio  
and video streams from an HDMI input will be output to  
the TV or other components via HDMI connection. In  
standby mode, the HDMI THRU and HDMI indicators  
will light (HDMI will be dimly-lit).  
This setting is fixed to “Auto” automatically when the  
above “HDMI Ctrl (RIHD)” setting is set to “On”,  
resulting in automatic input source selection.  
Note  
• When the setting is set to “On” and the menu is closed, the names  
of connected p-compatible components and “RIHD On”  
are displayed on the AV receiver.  
• With some TVs and input signals, no sound may be output even  
when this setting is set to On.  
• When Audio TV Out” or HDMI Ctrl (RIHD)” is set to On”  
and you’re listening through your TV’s speakers (page 16),  
turning up the AV receiver’s volume control will make the sound  
be output from the AV receiver’s front left and right speakers. To  
stop the AV receiver’s speakers producing sound, change the  
settings, change your TV’s settings, or turn down the AV  
receiver’s volume.  
Search…(name)RIHD On”  
When the AV receiver cannot receive the name of the component,  
it is displayed as “Player*” or “Recorder*”, etc (“ ” shows up  
and indicates the number of components, when two or more are  
received).  
*
• When an p-compatible component is connected to the  
AV receiver via an HDMI cable, the name of the connected  
component is displayed on the AV receiver display. For example,  
while you are watching TV broadcasting, if you operate a Blu-ray  
Disc/DVD player (being powered on) with the remote control of  
the AV receiver, the name of the Blu-ray Disc/DVD player will  
be displayed on the AV receiver.  
• Set it to Offwhen a connected piece of equipment is not  
compatible or it is unclear whether the equipment is compatible  
or not.  
Note  
• Only the input source assigned to the HDMI IN via  
HDMI Input” is enabled (page 39).  
• The power consumption in standby mode will increase during the  
HDMI Through function; however in the following cases, the  
power consumption can be saved:  
• Listening mode cannot be changed when this setting is set to  
On” and the input source is not HDMI.  
– The TV is in standby mode.  
– You are watching a TV program.  
• Refer to the connected component’s instruction manual for  
details.  
• Depending on the connected component, the correct input source  
may not be selected with the setting fixed to “Auto”.  
• This setting is set to “Off” automatically when the “HDMI Ctrl  
(RIHD)” setting is set to “Off”.  
• If operation is not normal when set to On, change the setting to  
Off.  
• Refer to the connected component’s instruction manual for  
details.  
• When the “HDMI Ctrl (RIHD)” setting is set to “On”, the power  
consumption in standby mode slightly increases. (Depending on  
the TV status, the AV receiver will enter standby mode as usual.)  
En-45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Advanced Operations  
Audio Return Ch (ARC)  
`Off  
Speaker Levels  
Using the Audio Settings  
Subwoofer Level  
`Auto:  
You can change various audio settings from the Home  
The audio signal from your TV tuner can be sent to  
the HDMI OUT of the AV receiver.  
The audio return channel (ARC) function allows an ARC  
capable TV to send the audio stream to the HDMI OUT of  
the AV receiver. To use this function, you must select the  
TV/CD input selector and your TV must be ARC capable.  
menu (page 33).  
`–15 dB to 0 dB to +12 dB in 1 dB steps  
Operating on the remote controller directly  
Press RECEIVER followed by HOME.  
1
Press RECEIVER once followed by TONE  
repeatedly to select “Subwoofer”.  
1
Use q/wand ENTER to select “Audio”, and then  
2
use q/w/e/rto make the desired selection.  
Use and + to adjust.  
2
Note  
Note  
• This setting is fixed to “- - - -” when the “HDMI Ctrl (RIHD)”  
setting is set to “Off”.  
Tip  
• These settings are not available in either of the following cases:  
– The “Audio TV Out” setting is set to “On” (page 45).  
– “HDMI Ctrl (RIHD)” is set to “On” (page 45) and you’re  
listening through your TV speakers.  
• This setting is set to “Auto” automatically when the “HDMI Ctrl  
(RIHD)” setting is set to “On” for the first time.  
• If you set “Audio Return Ch” to “Auto”, the “Audio Selector”  
settings of the TV/CD input selector will be automatically  
switched to “ARC” (page 43).  
• Alternatively, you can use the AV receiver’s TONE and /+.  
`–12 dB to 0 dB to +12 dB in 1 dB steps  
You can adjust the volume of each speaker while listening  
to an input source.  
These temporary adjustments are cancelled when the AV  
receiver is set to standby. To save the setting you made  
here, go to “Level Cal (Level Calibration)” (page 41)  
before setting the AV receiver to standby.  
Tone Control  
LipSync  
`Off  
`On  
Bass  
`–10 dB to 0 dB to +10 dB in 2 dB steps  
You can boost or cut low-frequency sounds output  
from the front speakers.  
This function allows the AV receiver to automatically  
correct any delay between the video and the audio, based  
on the data from the connected monitor.  
Note  
Treble  
`–10 dB to 0 dB to +10 dB in 2 dB steps  
You can boost or cut high-frequency sounds output  
from the front speakers.  
You can adjust the bass and treble for Speakers A and B  
front speakers, except when the Direct listening mode is  
selected.  
• These settings cannot be calibrated in either of the following  
cases:  
– A pair of headphones is connected.  
– The AV receiver is muted.  
• Speakers that are set to “No” or “None” in the “Sp Config  
(Speaker Configuration)” (page 40) cannot be adjusted.  
Note  
• This function works only if your HDMI-compatible TV supports  
HDMI Lip Sync.  
After changing the settings of the HDMI Ctrl  
(RIHD), HDMI Throughor Audio Return Ch”  
turn off the power on all connected pieces of equipment  
and then turn them on again. Refer to the user’s manuals  
for all connected pieces of equipment.  
Operating on the remote controller directly  
Press RECEIVER once followed by TONE  
repeatedly to select either “Bass” or “Treble”.  
1
Use and + to adjust.  
2
Tip  
• Alternatively, you can use the AV receiver’s TONE and /+.  
En-46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Advanced Operations  
EX.BASS  
Late Night  
Music Optimizer  
EX.BASS  
Late Night  
Music Optimizer  
`Off  
For Dolby Digital and Dolby Digital Plus sources, the  
`Off  
options are:  
`On  
`On  
`Off  
`Low:  
EX.BASS is a technology that have developed by  
experiments and listening tests to reproduce a natural  
deeper bass. When you turn the mode on, you can get  
dynamic and deeper presence on your movies and music.  
The Music Optimizer function enhances the sound quality  
of compressed music files. The M.Opt indicator lights on  
Small reduction in dynamic range.  
`High:  
Tip  
Large reduction in dynamic range.  
Note  
• Alternatively, you can use the AV receiver’s MUSIC  
OPTIMIZER.  
For Dolby TrueHD sources, the options are:  
`Auto:  
The Late Night function is set to “On” or “Off”  
automatically.  
`Off  
`On  
Turn this setting on to reduce the dynamic range of Dolby  
Digital material so that you can still hear quiet parts even  
when listening at low volume levels—ideal for watching  
movies late at night when you don’t want to disturb  
anyone.  
• This setting is not available in either of the following cases:  
– A pair of headphones is connected.  
– Speakers B is on.  
– Speakers A is off.  
– Direct listening mode is selected.  
– The “Subwoofer” setting is set to “No” (page 40).  
Note  
• The Music Optimizer function only works with PCM digital  
audio input signals with a sampling rate below 48 kHz and analog  
audio input signals.  
• The Music Optimizer is disabled when the Direct listening mode  
is selected.  
• The setting is stored individually for each input selector.  
CinemaFILTER  
Cinema Filter  
`Off  
Note  
• The effect of the Late Night function depends on the material that  
you are playing and the intention of the original sound designer,  
and with some material there will be little or no effect when you  
select the different options.  
• The Late Night function can be used only when the input source  
is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.  
• The Late Night function is set to “Off” when the AV receiver is  
set to standby. For Dolby TrueHD sources, it will be set to  
Auto”.  
`On  
Turn this setting on to soften overly bright movie  
soundtracks, which are typically mixed for reproduction in  
a movie theater.  
CinemaFILTER can be used with the following listening  
modes: Dolby Digital, Dolby Digital Plus, Dolby TrueHD,  
Dolby Pro Logic II Movie, Multichannel, DTS, DTS Neo:6  
Cinema, DTS 96/24, DTS-HD High Resolution Audio,  
DTS-HD Master Audio and DTS Express.  
Note  
• The CinemaFILTER may not work when used with certain input  
sources.  
En-47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Controlling Other Components  
System Function  
Operating Notes  
• Use the AV receiver’s volume control to adjust the playback  
volume.  
• While your iPod/iPhone is inserted in the RI Dock, its volume  
control has no effect.  
• If you do adjust the volume control on your iPod/iPhone while  
it’s inserted in the RI Dock, be careful that it’s not set too loud  
before you reconnect your headphones.  
iPod/iPhone Playback  
via Onkyo Dock  
System On  
When you turn on the AV receiver, the RI Dock and  
iPod/iPhone turn on automatically. In addition, when RI  
Dock and iPod/iPhone are on, the AV receiver can be  
turned on by pressing 8.  
Using the Onkyo Dock  
Auto Power On  
The Dock is sold separately. Models sold are different  
depending on the region.  
For the latest information on the Onkyo Dock  
components, see the Onkyo web site at:  
If you press the remote controller’s 1(Playback) while  
the AV receiver is on standby, the AV receiver will  
automatically turn on, select your iPod/iPhone as the input  
source, and your iPod/iPhone will start playback.  
Before using the Onkyo Dock components, update  
your iPod/iPhone with the latest software, available  
from the Apple web site.  
For supported iPod/iPhone models, see the instruction  
manual of the Onkyo Dock.  
Direct Change  
If you start iPod/iPhone playback while listening to another  
input source, the AV receiver will automatically switch to  
the input to which RI Dock is connected.  
Other Remote Operations  
You can use the remote controller that came with the AV  
receiver to control other iPod/iPhone functions. The  
available functionality depends on the AV receiver.  
RI Dock  
With the RI Dock, you can easily play the music stored on  
your Apple iPod/iPhone through the AV receiver and enjoy  
great sound, and watch iPod/iPhone slideshows and videos  
on your TV. In addition, the on-screen display (OSD)  
allows you to view, navigate, and select your iPod/iPhone  
model’s contents on your TV, and with the supplied remote  
controller, you can control your iPod/iPhone from the  
comfort of your sofa. You can even use the AV receiver’s  
remote controller to operate your iPod/iPhone.  
iPod/iPhone Alarm  
If you use the Alarm function on your iPod/iPhone to start  
playback, the AV receiver will turn on at the specified time  
and select your iPod/iPhone as the input source  
automatically.  
Note  
• Linked operations do not work with video playback or when the  
alarm is set to play a sound.  
Note  
• If you use your iPod/iPhone with any other accessories,  
iPod/iPhone playback detection may not work.  
• The System On function may not work depending on the RI  
Dock.  
• Enter the appropriate remote control code before using the AV  
receiver’s remote controller for the first time (page 50).  
• Connect the RI Dock to the AV receiver with an ucable  
(page 18).  
• Set the RI Dock’s RI MODE switch to “HDD” or  
“HDD/DOCK”.  
• Set the AV receiver’s Input Display to “DOCK” (page 35).  
En-48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Controlling Other Components  
uDock operation  
b
Controlling Your iPod/iPhone  
Press the appropriate REMOTE  
MODE button first.  
Available buttons  
By pressing the REMOTE MODE button that’s been  
programmed with the remote control code for your Dock,  
you can control your iPod/iPhone in the Dock with the  
buttons described further in this section.  
See “Entering Remote Control Codes” for details on  
entering a remote control code (page 50).  
DISPLAY*3  
*1  
a 8  
f
TOP MENU*2  
MUTING  
g
ALBUM +/–  
c q/w/e/r, ENTER  
h
PLAYLIST e/r  
i VOL q/w  
k
a
f
MENU  
d 1, 3, 2, 5, 4,  
j
7, 6  
See the Dock’s instruction manual for more information.  
REPEAT  
MODE*4  
e
g
h
RI Dock  
RANDOM  
• Set the RI Dock’s RI MODE switch to “HDD” or  
“HDD/DOCK”.  
Note  
i
With some iPod/iPhone models, generations and RI Docks,  
certain buttons may not work as expected.  
• For detailed operation of iPod/iPhone, please refer to the  
8may not work with a remote control code (without  
u). In this case, make an uconnection and enter the  
remote control code 81993 (with u).  
b
c
j
instruction manual of the RI Dock.  
*1  
This button does not turn the Onkyo DS-A2 or DS-A2X RI  
With the RI Control  
Dock on or off. Also, your iPod/iPhone may not respond the  
first time you press this button, in which case you should press  
it again. This is because the remote controller transmits the On  
and Standby commands alternately, so if your iPod/iPhone is  
already on, it will remain on when the remote controller  
transmits the On command. Similarly, if your iPod/iPhone is  
already off, it will remain off when the remote controller  
transmits the Off command.  
Make an uconnection and enter the remote  
control code 81993 (with u).  
• Set the AV receiver’s Input Display to “DOCK”  
(page 35).  
d
e
Without the RI Control  
You must enter the remote control code 82990 first  
(page 51).  
*2  
TOP MENU works as the mode button when used with the  
k
DS-A2 RI Dock.  
*3  
DISPLAY turns on backlight for a second.  
Resume mode  
*4  
With the Resume function, you can resume playback of the  
song that was playing when you removed your iPod/iPhone  
from the RI Dock.  
En-49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Controlling Other Components  
Entering Remote Control Codes  
Remote Control Codes for Onkyo  
Controlling Other Onkyo  
Components  
Components Connected via u  
You’ll need to enter a code for each component that you  
want to control.  
Onkyo components that are connected via uare  
controlled by pointing the remote controller at the AV  
receiver, not the component. This allows you to control  
components that are out of view, in a rack, for example.  
You can use the AV receiver’s remote controller to control  
your other Onkyo AV components. This section explains  
how to enter the remote control code for a component that  
you want to control: DVD, CD, etc.  
Look up the appropriate remote control code in the  
Remote Control Codes for Onkyo Components  
1
Connected via u.  
Make sure the Onkyo component is connected with  
While holding down the REMOTE MODE button to  
1
2
Preprogrammed Remote Control  
Codes  
which you want to assign a code, press and hold  
down DISPLAY (about 3 seconds).  
The remote indicator lights.  
an ucable and an analog audio cable (RCA).  
See “Connecting Onkyo uComponents” for details  
(page 18).  
The following REMOTE MODE butttons are  
preprogrammed with remote control codes for controlling  
the components listed. You do not need to enter a remote  
control code to control these components.  
For details on controlling these components, see the  
indicated pages.  
Note  
Enter the appropriate remote control code for a  
2
REMOTE MODE button, by referring to the  
previous section.  
• Remote control codes cannot be entered for RECEIVER.  
• Except for RECEIVER remote control codes from any  
category can be assigned to the REMOTE MODE button.  
However, these buttons also work as input selector buttons  
(page 21), so choose a REMOTE MODE button that  
corresponds with the input to which you connect your  
component. For example, if you connect your CD player to  
the CD input, choose TV/CD when entering its remote  
control code.  
`42157:  
Onkyo cassette tape deck with u  
`81993:  
BD/DVD Onkyo Blu-ray Disc player (page 52)  
Onkyo Dock with u  
TV/CD  
Onkyo CD player (page 53)  
Press the REMOTE MODE button, point the  
remote controller at the AV receiver, and operate  
the component.  
3
Within 30 seconds, use the number buttons to enter  
the 5-digit remote control code.  
3
The remote indicator flashes twice.  
If the remote control code is not entered successfully,  
the remote indicator will flash once slowly.  
To be continued  
En-50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Controlling Other Components  
Controlling Onkyo components without u  
If you want to control an Onkyo component by pointing the  
remote controller directly at it, or you want to control an  
Onkyo component that’s not connected via u, use the  
following remote control codes:  
`30627:  
Resetting the REMOTE MODE Buttons  
Resetting the Remote Controller  
You can reset a REMOTE MODE button to its default  
remote control code.  
You can reset the remote controller to its default settings.  
While holding down RECEIVER, press and hold  
down HOME until the remote indicator lights  
1
While holding down the REMOTE MODE button  
that you want to reset, press and hold down HOME  
1
(about 3 seconds).  
Onkyo DVD player without u  
until the remote indicator lights (about 3 seconds).  
Within 30 seconds, press RECEIVER again.  
The remote indicator flashes twice, indicating that the  
remote controller has been reset.  
`71817:  
Within 30 seconds, press the REMOTE MODE  
button again.  
Onkyo CD player without u  
`32900/33000:  
2
The remote indicator flashes twice, indicating that the  
button has been reset.  
Each REMOTE MODE button is preprogrammed  
with a remote control code. When a button is reset, its  
preprogrammed code is restored.  
Onkyo Blu-ray Disc player  
`32901/33004:  
Onkyo HD DVD player  
`70868:  
Onkyo MD recorder without u  
`71323:  
Onkyo CD recorder without u  
`82990:  
Onkyo Dock without u  
En-51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Controlling Other Components  
Blu-ray Disc player / HD-DVD player operation  
Controlling Other Components  
Press the appropriate REMOTE  
MODE button first.  
Available buttons  
By pressing the REMOTE MODE button that’s been  
programmed with the remote control code for your  
component, you can control Onkyo component as  
described below.  
For details on entering a remote control code for other  
components, see “Entering Remote Control Codes”  
(page 50).  
Number: 1 to 9, 0  
a 8  
g
Number: +10*1  
DISPLAY  
MUTING  
DISC +/–  
MENU  
TOP MENU  
b
c q/w/e/r, ENTER  
h
i
j
k
l
m
n
SETUP  
d
a
h
e 1, 3, 2, 5, 4,  
7, 6  
Red (A)  
RETURN  
AUDIO*1  
CLR  
f
i
j
Controlling a Blu-ray Disc/DVD Player, HD  
DVD Player  
Green (B)  
Yellow (C)  
Blue (D)  
BD/DVD is preprogrammed with the remote control code  
*1  
for controlling a component that supports the p  
DVD player operation  
(limited to some models). The component must be able to  
receive remote control commands via pand be  
connected to the AV receiver via HDMI.  
Use the following remote control codes:  
`32910/33001/31612:  
Available buttons  
b
c
d
k
Number: 1 to 9, 0  
a 8  
g
TOP MENU  
Number: +10*1  
DISPLAY  
MUTING  
DISC +/–  
MENU  
b
c q/w/e/r, ENTER  
h
i
j
k
l
m
n
l
m
SETUP  
d
Blu-ray Disc/DVD player with p  
e 1, 3, 2, 5, 4,  
7, 6  
*1  
The psupported by the AV receiver is the CEC system  
e
f
SEARCH*1  
RETURN  
AUDIO*1  
CLR  
control function of the HDMI standard.  
f
REPEAT  
RANDOM*1  
MODE*1  
g
n
En-52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Controlling Other Components  
CD player / CD recorder / MD recorder operation  
Press the appropriate REMOTE  
MODE button first.  
Available buttons  
Number: 1 to 9, 0  
a 8  
g
Number: +10  
DISPLAY  
MUTING  
DISC +/–  
CLR  
c q/w/e/r, ENTER  
SETUP  
d
h
i
j
n
e 1, 3, 2, 5, 4,  
a
h
7, 6  
SEARCH  
REPEAT  
RANDOM  
MODE  
f
i
j
Cassette tape deck operation  
Available buttons  
MUTING  
a 8  
i
e 1, t(reverse  
playback), 2, 5, 4,  
7, 6  
c
d
Note  
• With some components, certain buttons may not work as  
expected, and some may not work at all.  
e
f
• See “Controlling Your iPod/iPhone” about the operation of  
iPod/iPhone (page 49).  
*1  
The pfunction is not supported. The p  
supported by the AV receiver is the CEC system control  
function of the HDMI standard.  
g
n
En-53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Appendix  
Audio  
The on-screen menus appear only on a TV that is  
connected to the HDMI OUT. If your TV is connected  
to other video outputs, use the AV receiver’s display  
when changing settings.  
Troubleshooting  
There’s no sound, or it’s very quiet  
If you have any trouble using the AV receiver, look for a  
solution in this section. If you can’t resolve the issue  
yourself, contact your Onkyo dealer.  
Press SPEAKERS A or B to turn on the speaker  
indicator that you want to output sound.  
33  
40  
Make sure that the digital input source is selected  
properly.  
Power  
If you can’t resolve the issue yourself, try resetting the  
AV receiver before contacting your Onkyo dealer.  
To reset the AV receiver to its factory defaults, turn it  
on and, while holding down VCR/DVR, press  
8ON/STANDBY. “Clear” will appear on the AV  
receiver’s display and the AV receiver will enter  
standby mode.  
Make sure that all audio connecting plugs are pushed 15  
in all the way.  
Can’t turn on the AV receiver  
Make sure that the power cord is properly plugged  
into the wall outlet.  
Make sure that the inputs and outputs of all  
components are connected properly.  
16-18  
14  
Unplug the power cord from the wall outlet, wait five  
seconds or more, then plug it in again.  
Make sure that the polarity of the speaker cables is  
correct, and that the bare wires are in contact with the  
metal part of each speaker terminal.  
The AV receiver turns off unexpectedly  
Make sure that the input source is properly selected. 21  
The AV receiver will automatically enter standby  
mode when Auto Standby has been set and launches.  
44  
Make sure that the speaker cables are not shorting.  
14  
Check the volume. The AV receiver is designed for  
home theater enjoyment. It has a wide volume range,  
allowing precise adjustment.  
The AV receiver turns off and after restoring the  
Note that resetting the AV receiver will delete your radio  
presets and custom settings.  
power, it turns off again  
If the MUTING indicator is flashing on the AV  
receiver’s display, press the remote controller’s  
MUTING to unmute the AV receiver.  
35  
The protection circuit has been activated. Remove the 14  
power cord from the wall outlet immediately. Make  
sure that all speaker cables and input sources are  
properly connected, and leave the AV receiver with  
its power cord disconnected for 1 hour. After that,  
reconnect the power cord and turn the power on. If  
the AV receiver turns off again, unplug the power  
cord and contact your Onkyo dealer.  
While a pair of headphones is connected to the  
PHONES jack, no sound is output from the speakers.  
36  
Remote indicator  
If there’s no sound from a DVD player connected to  
an HDMI IN, check the DVD player’s output  
settings, and be sure to select a supported audio  
format.  
Caution: If “CHECK SP WIRE” appears on the AV  
receiver’s display, the speaker cables may be  
shorting.  
RECEIVER  
HOME  
Check the digital audio output setting on the  
connected device. On some game consoles, such as  
those that support DVD, the default setting is off.  
With some DVD-Video discs, you need to select an  
audio output format from a menu.  
WARNING  
If smoke, smell or abnormal noise is produced by the AV  
receiver, unplug the power cord from the wall outlet  
immediately and contact your Onkyo dealer.  
If your turntable uses an MC cartridge, you must  
connect an MC head amp, or an MC transformer.  
Make sure that none of the connecting cables are  
bent, twisted, or damaged.  
To reset the remote controller to its factory defaults,  
while holding down RECEIVER, press and hold down  
HOME until the remote indicator lights (about 3  
seconds). Within 30 seconds, press RECEIVER  
again.  
Not all listening modes use all speakers.  
29  
41  
Specify the speaker distances and adjust the  
individual speaker levels.  
En-54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Appendix  
There’s no sound with a certain signal format  
About DTS signals  
If the input signal format is set to “PCM” or “DTS”. 44  
Set it to “Off”.  
Check the digital audio output setting on the  
connected device. On some game consoles, such as  
those that support DVD, the default setting is off.  
When DTS program material ends and the DTS  
bitstream stops, the AV receiver remains in DTS  
listening mode and the dts indicator remains on. This  
is to prevent noise when you use the pause, fast  
forward, or fast reverse function on your player. If  
you switch your player from DTS to PCM, because  
the AV receiver does not switch formats  
immediately, you may not hear any sound, in which  
case you should stop your player for about three  
seconds, and then resume playback.  
With some DVD-Video discs, you need to select an  
audio output format from a menu.  
When the Stereo or Mono listening mode is selected, 31  
only the front speakers and subwoofer produce  
sound.  
Depending on the input signal, some listening modes 29-30  
cannot be selected.  
Check the Speaker Configuration.  
40  
Can’t get 5.1 playback  
Only the center speaker produces sound  
With some CD and LD players, you won’t be able to  
playback DTS material properly even though your  
player is connected to a digital input on the AV  
receiver. This is usually because the DTS bitstream  
has been processed (e.g., output level, sampling rate,  
or frequency response changed) and the AV receiver  
doesn’t recognize it as a genuine DTS signal. In such  
cases, you may hear noise.  
When Speaker B is turned on, Speakers A is reduced 33  
to 2.1-channel playback.  
If you use the Dolby Pro Logic II Movie, Dolby Pro  
Logic II Music, or Dolby Pro Logic II Game listening  
mode with a mono source, such as an AM radio  
station or mono TV program, the sound is  
concentrated in the center speaker.  
Depending on the number of connected speakers, it is 29-30  
not always possible to select all of the listening  
modes.  
Make sure the speakers are configured correctly.  
40  
The speaker volume cannot be set as required  
The surround speakers produce no sound  
Playing DTS program material, using the pause, fast  
forward, or fast reverse function on your player may  
produce a short audible noise. This is not a  
malfunction.  
After the volume level of each individual speaker has 41  
been adjusted, the maximum volume may be reduced.  
When the T-D (Theater-Dimensional), Stereo or  
Mono listening mode is selected, the surround  
speakers produce no sound.  
Noise can be heard  
Depending on the source and current listening mode, 28  
not much sound may be produced by the surround  
speakers. Try selecting another listening mode.  
Using cable ties to bundle audio cables with power  
cords, speaker cables, and the like may degrade the  
audio performance, so refrain from doing it.  
The beginning of audio received by an HDMI IN  
can’t be heard  
Make sure the speakers are configured correctly.  
40  
Since it takes longer to identify the format of an  
HDMI signal than it does for other digital audio  
signals, audio output may not start immediately.  
An audio cable may be picking up interference. Try  
repositioning your cables.  
The center speaker produces no sound  
The Late Night function doesn’t work  
When the Stereo or Mono listening mode is selected,  
the center speaker produces no sound.  
Make sure the source material is Dolby Digital,  
Dolby Digital Plus, or Dolby TrueHD.  
47  
Make sure the speakers are configured correctly.  
40  
The subwoofer produces no sound  
The subwoofer outputs no sound while only Speakers 33  
B is on. Turn on Speakers A.  
When you play source material that contains no  
information in the LFE channel, the subwoofer  
produces no sound.  
Make sure the speakers are configured correctly.  
40  
En-55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Can’t control other components  
Video  
Tuner  
18  
If it’s an Onkyo component, make sure that the u  
There’s no picture  
Reception is noisy, FM stereo reception is noisy,  
or the FM STEREO indicator doesn’t light  
cable and analog audio cable are connected properly.  
Connecting only an ucable won’t be enough.  
Make sure that all video connecting plugs are pushed 15  
in all the way.  
Make sure you’ve selected the correct remote  
controller mode.  
11, 52  
Relocate your antenna.  
Make sure that each video component is properly  
connected.  
16, 18  
Move the AV receiver away from your TV or  
computer.  
For a proper operation of the remote controller as a  
cassette tape deck is connected to the TV/CD IN jack,  
or as an RI Dock is connected to the TV/CD IN,  
VCR/DVR IN or GAME IN jacks, you must set the  
input display accordingly.  
35  
If the video source is connected to a component video 17, 39  
input, you must assign that input to an input selector,  
and your TV must be connected to COMPONENT  
VIDEO OUT.  
Listen to the station in mono.  
25  
When listening to an AM station, operating the  
remote controller may cause noise.  
Passing cars and airplanes can cause interference.  
Concrete walls weaken radio signals.  
If you cannot operate it, you will need to enter the  
appropriate remote control code.  
50  
If the video source is connected to a composite video 17  
input, your TV must be connected to the  
corresponding composite video output.  
If nothing improves the reception, install an outdoor  
antenna.  
To control an Onkyo component that’s connected via 50  
u, point the remote controller at the AV receiver.  
Be sure to enter the appropriate remote control code  
first.  
If the video source is connected to an HDMI input,  
you must assign that input to an input selector, and  
your TV must be connected to the HDMI OUT.  
16, 39  
Remote Controller  
To control an Onkyo component that’s not connected 51  
via u, point the remote controller at the component.  
Be sure to enter the appropriate remote control code  
first.  
On your TV, make sure that the video input to which  
the AV receiver is connected is selected.  
The remote controller doesn’t work  
Before operating this unit, be sure to press  
RECEIVER.  
5
There’s no picture from a source connected to  
an HDMI IN  
Make sure that the batteries are installed with the  
correct polarity.  
uDock for iPod/iPhone  
Reliable operation with an HDMI-to-DVI adapter is 62  
not guaranteed. In addition, video signals from a PC  
are not guaranteed.  
Install new batteries. Don’t mix different types of  
batteries, or old and new batteries.  
5
There’s no sound  
Make sure your iPod/iPhone is actually playing.  
Make sure that the remote controller is not too far  
away from the AV receiver, and that there’s no  
obstruction between the remote controller and the AV  
receiver’s remote control sensor.  
5
The on-screen menus don’t appear  
Make sure your iPod/iPhone is properly inserted in  
the Dock.  
On your TV, make sure that the video input to which  
the AV receiver is connected is selected.  
Make sure the AV receiver is turned on, the correct  
input source is selected, and the volume is turned up.  
Make sure that the AV receiver is not subjected to  
direct sunshine or inverter-type fluorescent lights.  
Relocate if necessary.  
When the AV receiver is not connected to a TV via  
HDMI OUT, on-screen menus are not displayed.  
Make sure the plugs are pushed in all the way.  
Try resetting your iPod/iPhone.  
If the AV receiver is installed in a rack or cabinet  
with colored-glass doors, the remote controller may  
not work reliably when the doors are closed.  
There’s no video  
Make sure you’ve selected the correct remote  
controller mode.  
11, 50  
Make sure that your iPod/iPhone model’s TV OUT  
setting is set to On.  
Make sure you’ve entered the correct remote control 50  
code.  
Make sure the correct input is selected on your TV or  
the AV receiver.  
Make sure to set the same ID on both the AV receiver 44  
and remote controller.  
Some versions of the iPod/iPhone do not output  
video.  
En-56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
The following settings can be made for the  
The AV receiver’s remote controller doesn’t  
control my iPod/iPhone  
USB Device Playback  
composite video inputs  
Can’t access the music files on a USB device  
You must use the buttons on the unit to make these  
settings.  
Make sure your iPod/iPhone is properly inserted in  
connect properly to the Dock. Always remove your  
iPod/iPhone from the case before inserting it into the  
Dock.  
Make sure the USB device is plugged in properly.  
On the AV receiver, press the input selector for the input  
source that you want to set and the SETUP button  
simultaneously. While holding down the input selector  
button, press SETUP until “Video ATT :On” appears  
on the AV receiver’s display. Then, release both buttons.  
To turn the setting off, repeat the above process so that  
Video ATT :Off” appears on the AV receiver’s  
display, and release the buttons.  
The AV receiver supports USB devices that support 63  
the USB mass storage device class. However,  
playback may not be possible with some USB devices  
even if they conform to the USB mass storage device  
class.  
The iPod/iPhone cannot be operated while it’s  
displaying the Apple logo.  
Make sure you’ve selected the right remote mode.  
49  
USB memory devices with security functions cannot 24  
be played.  
When you use the AV receiver’s remote controller,  
point it toward your AV receiver.  
If you still can’t control your iPod/iPhone, start  
playback by pressing your iPod/iPhone model’s Play  
button. Remote operation should then be possible.  
• Video Attenuation  
Others  
This setting can be made for the BD/DVD, VCR/DVR,  
CBL/SAT, GAME, AUX, or USB input.  
If you have a games console connected to the composite  
video input, and the picture isn’t very clear, you can  
attenuate the gain.  
Video ATT :Off: (default).  
Video ATT :On: Gain is reduced by 2 dB.  
Standby power consumption  
Try resetting your iPod/iPhone.  
In the following cases, the power consumption in  
standby mode may reach up to a maximum of 31 W:  
– “HDMI Ctrl (RIHD)” setting is set to “On”.  
(Depending on the TV status, the AV receiver will  
enter standby mode as usual.)  
45  
Depending on your iPod/iPhone, some buttons may  
not work as expected.  
The AV receiver unexpectedly selects my  
iPod/iPhone as the input source  
– The “HDMI Through” setting is set to other than  
Off”.  
Always pause iPod/iPhone playback before selecting  
a different input source. If playback is not paused, the  
Direct Change function may select your iPod/iPhone  
as the input source by mistake during the transition  
between tracks.  
If the picture on your TV/monitor connected to  
the HDMI OUT is unstable, try switching the  
DeepColor function off  
The sound changes when I connect my  
headphones  
To turn off the DeepColor function, simultaneously  
press the CBL/SAT and 8ON/STANDBY buttons on  
the AV receiver. While holding down CBL/SAT, press  
8ON/STANDBY until “Deep Color: Off” appears on  
the AV receiver’s display. Then, release both buttons.  
To reactivate the DeepColor function, repeat the above  
process until “Deep Color: On” appears on the AV  
receiver’s display and release the buttons.  
When a pair of headphones is connected, the listening  
mode is set to Stereo, unless it’s already set to Stereo,  
Mono, or Direct.  
iPod/iPhone doesn’t work properly  
Try reconnecting your iPod/iPhone.  
How do I change the language of a multiplex  
source  
Recording  
Use the “Input Ch (Mux)” setting on the “Audio  
42  
Can’t record  
Adjust” menu to select “Main” or “Sub”.  
On your recorder, make sure the correct input is  
selected.  
The ufunctions don’t work  
To prevent signal loops and damage to the AV  
receiver, input signals are not fed through to outputs  
with the same name (e.g., VCR/DVR IN to  
VCR/DVR OUT).  
18  
To use u, you must make an uconnection and an  
analog audio connection (RCA) between the  
component and AV receiver, even if they are  
connected digitally.  
En-57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
The AV receiver contains a microcomputer for signal  
processing and control functions. In very rare situations,  
severe interference, noise from an external source, or  
static electricity may cause it to lockup. In the unlikely  
event that this happens, unplug the power cord from the  
wall outlet, wait at least five seconds, and then plug it  
back in.  
Onkyo is not responsible for damages (such as CD  
rental fees) due to unsuccessful recordings caused by  
the unit’s malfunction. Before you record important  
data, make sure that the material will be recorded  
correctly.  
Before disconnecting the power cord from the wall  
outlet, set the AV receiver to standby.  
En-58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Video Connection Formats  
Audio Connection Formats  
Connection Tips and  
Video Signal Path  
Video components can be connected by using any one of  
the following video connection formats: composite video,  
component video, or HDMI, the latter offering the best  
picture quality.  
Audio components can be connected by using any of the  
following audio connection formats: analog, optical,  
coaxial, or HDMI.  
When choosing a connection format, bear in mind that the  
AV receiver does not convert digital input signals for  
analog line outputs and vice versa. For example, audio  
signals connected to an optical or coaxial digital input are  
not output by the analog VCR/DVR OUT.  
The AV receiver supports several connection formats for  
compatibility with a wide range of AV equipment. The  
format you choose will depend on the formats supported by  
your components. Use the following sections as a guide.  
When choosing a connection format, bear in mind that the  
AV receiver doesn’t convert between formats, so only  
outputs of the same format as the input will output the  
signal.  
The on-screen menus appear only on a TV that is  
connected to the HDMI OUT. If your TV is connected  
to other video outputs, use the AV receiver’s display  
when changing settings.  
If signals are present at more than one input, the inputs will  
be selected automatically in the following order of priority:  
HDMI, digital, analog.  
Video Signal Flow Chart  
Blu-ray Disc/DVD player, etc.  
Note  
Audio Signal Flow Chart  
• The on-screen setup menus are displayed when:  
– There is no video input, or  
– The video input is 480p, 576p, 720p, 1080i, or 1080p.  
Composite  
Component  
HDMI  
HDMI  
Blu-ray Disc/DVD player, etc.  
IN  
AV receiver  
Analog  
Optical  
Coaxial  
HDMI  
IN  
*1  
MONITOR OUT  
*1  
Composite  
Component  
*1  
AV receiver  
OUT  
TV, projector, etc.  
Analog  
HDMI  
*1 *2  
TV, projector, etc.  
Depends on the “Audio TV Out” setting (page 45).  
This is possible, when “Audio Return Ch” is set to “Auto”  
(page 46), the TV/CD input selector is selected, and your  
TV is ARC capable.  
*1  
*2  
Tip  
• When a signal is input via HDMI and the corresponding input  
selector is selected, the HDMI indicator lights.  
En-59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Appendix  
Operations that can be performed with  
Using an RIHD-  
compatible TV, Player,  
or Recorder  
p, which stands for Remote Interactive over  
HDMI, is the name of the system control function found on  
Onkyo components. The AV receiver can be used with  
CEC (Consumer Electronics Control), which allows  
system control over HDMI and is part of the HDMI  
standard. CEC provides interoperability between various  
components, however, operation with components other  
than p-compatible components cannot be  
guaranteed.  
About p-compatible components  
TV  
• Toshiba TV  
• Sharp TV  
pconnection  
The following components are p-compatible (As  
For p-compatible TV  
of January 2012).  
The following linked operations are enabled by connecting  
the AV receiver to an p-compatible TV.  
• The AV receiver will enter standby mode when the power  
of the TV is turned to standby.  
Players/Recorders  
• You can set on the menu screen of the TV to either output  
the audio from the speakers connected to the AV  
receiver, or from the speakers of the TV.  
• Onkyo and Integra p-compatible players  
• Toshiba players and recorders (only when used together  
with Toshiba TV)  
• It is possible to output the video/audio coming from the  
antenna or from the input jack of the TV from the  
speakers connected to the AV receiver. (A connection  
such as optical digital cable or similar is required above  
the HDMI cable.)  
• Sharp players and recorders (only when used together  
with Sharp TV)  
*
Models other than those mentioned above may have some  
interoperability if compatible with CEC which is part of the  
HDMI Standard, but operation cannot be guaranteed.  
• Input to the AV receiver can be selected with the remote  
controller of the TV.  
• Operations such as volume adjustment or similar for the  
AV receiver can be performed from the remote controller  
of the TV.  
Note  
• For proper linked operations, do not connect more p-  
compatible components than the quantities specified below, to  
the HDMI input terminal.  
For p-compatible players/recorders  
The following linked operations are enabled by connecting  
the AV receiver to an p-compatible  
player/recorder.  
– Blu-ray Disc/DVD players: up to three.  
– Blu-ray Disc/DVD recorders/Digital Video Recorders: up to  
three.  
• When the playback is started on the player/recorder, input  
of the AV receiver will switch to the HDMI input of the  
player/recorder that is playing back.  
– Cable/Satellite Set-top boxes: up to four.  
• Do not connect the AV receiver to the other AV receiver/AV  
amplifier via HDMI.  
• Proper linked operations are not guaranteed when more  
p-compatible components than the above-mentioned  
quantities are connected.  
• Operation of the player/recorder is possible using the  
remote controller supplied with the AV receiver.  
*
Depending on the model used, not all operations may be  
available.  
To be continued  
En-60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Appendix  
How to connect and setup  
Change each item in the “HDMI Setup” menu  
according to the following settings:  
HDMI Ctrl (RIHD): On  
Operate with the remote controller.  
For buttons that can be operated (page 50).  
2
3
4
Confirm the connecting and setting.  
1. Connect the HDMI OUT jack to the HDMI input  
1
Note  
Audio Return Ch (ARC): Auto  
• Audio from DVD-Audio or Super Audio CD may not output  
from the TV speakers. You will be able to output the audio  
from the TV speakers by setting the audio output of the  
DVD player to 2ch PCM. (It may not be possible depending  
on the player models.)  
• Even if you set to output audio on the TV speakers, audio  
will be output from the speakers connected to the AV  
receiver when you adjust the volume or switch the input on  
the AV receiver. To output audio from the TV speakers, re-  
do the operations on the TV.  
jack of the TV.  
Blu-ray Disc/DVD player, etc.  
See details of each setting (pages 45, 46).  
Confirm the settings.  
1. Turn on the power for all connected components.  
2. Turn off the power of the TV, and confirm that the  
power of the connected components is turned off  
automatically with the link operation.  
3. Turn on the power of the Blu-ray Disc/DVD  
player/recorder.  
4. Start playback on the Blu-ray Disc/DVD  
player/recorder, and verify the following.  
• The AV receiver automatically turns on, and  
selects the input to which the Blu-ray  
Disc/DVD player/recorder is connected.  
• The TV automatically turns on, and selects the  
input to which the AV receiver is connected.  
5. Following the operating instructions of the TV,  
select “Use the TV speakers” from the menu  
screen of the TV, and confirm that the audio is  
output from the speakers of the TV, and not from  
the speakers connected to the AV receiver.  
6. Select “Use the speakers connected from the AV  
receiver” from the menu screen of the TV, and  
confirm that the audio is output from the speakers  
connected to the AV receiver, and not from the  
TV speakers.  
HDMI  
connection  
AV receiver  
• In case of an pconnection with uand uaudio  
control compatible components, do not connect the u  
cable at the same time.  
DIGITAL AUDIO  
connection  
(OPTICAL)  
HDMI  
connection  
• On the TV, when you select anything other than the HDMI  
jack to which the AV receiver is connected, the input on the  
AV receiver will be switched to “TV/CD”.  
TV, projector, etc.  
• The AV receiver will automatically power on in conjunction  
when it determines it to be necessary. Even if the AV  
receiver is connected to an pcompatible TV or  
player/recorder, it will not power on if it is not necessary. It  
may not power on in conjunction when the TV is set to  
output audio from the TV.  
• Linked functions with the AV receiver may not work  
depending on the component model connected. In such  
cases, operate the AV receiver directly.  
2. Connect the audio output from the TV to the  
OPTICAL IN 2 jack of the AV receiver using an  
optical digital cable.  
Note  
• When the audio return channel (ARC) function is used with  
an ARC capable TV, this connection is not necessary  
(page 46).  
3. Connect the HDMI output of the Blu-ray  
Disc/DVD player/recorder to the HDMI IN 1 jack  
of the AV receiver.  
Note  
• It is necessary to assign the HDMI input when connecting  
the Blu-ray Disc/DVD player/recorder to other jacks  
(page 39). Do not assign the components connected to  
the HDMI IN to the TV/CD input at this time. Appropriate  
CEC (Consumer Electronics Control) operation can not be  
guaranteed.  
Note  
• Perform the above operations when you use the AV receiver  
for the first time, when the settings of each component are  
changed, when the main power of each component is turned  
off, when the power cable is disconnected from the power  
En-61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Supported Audio Formats  
About Copyright Protection  
About HDMI  
• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)  
• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz,  
16/20/24 bit)  
• Bitstream (DSD, Dolby Digital, Dolby Digital Plus,  
Dolby TrueHD, DTS, DTS-HD High Resolution Audio,  
DTS-HD Master Audio)  
The AV receiver supports HDCP (High-bandwidth Digital  
Designed to meet the increased demands of digital TV,  
HDMI (High Definition Multimedia Interface) is a new  
digital interface standard for connecting TVs, projectors,  
Blu-ray Disc/DVD players, set-top boxes, and other video  
components. Until now, several separate video and audio  
cables have been required to connect AV components.  
With HDMI, a single cable can carry control signals,  
digital video, and up to eight channels of digital audio (2-  
channel PCM, multichannel digital audio, and  
*2  
Content Protection) , a copy-protection system for digital  
video signals. Other devices connected to the AV receiver  
via HDMI must also support HDCP.  
*1  
DVI (Digital Visual Interface): The digital display interface  
Your Blu-ray Disc/DVD player must also support HDMI  
output of the above audio formats.  
*3  
standard set by the DDWG in 1999.  
*2  
HDCP (High-bandwidth Digital Content Protection): The  
video encryption technology developed by Intel for  
HDMI/DVI. It’s designed to protect video content and requires  
a HDCP-compatible device to display the encrypted video.  
multichannel PCM).  
The HDMI video stream (i.e., video signal) is compatible  
with DVI (Digital Visual Interface) , so TVs and displays  
with a DVI input can be connected by using an HDMI-to-  
DVI adapter cable. (This may not work with some TVs and  
displays, resulting in no picture.)  
*1  
*3  
DDWG (Digital Display Working Group): Lead by Intel,  
Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon  
Image, this open industry group’s objective is to address the  
industry’s requirements for a digital connectivity specification  
for high-performance PCs and digital displays.  
The AV receiver uses HDCP (High-bandwidth Digital  
*2  
Content Protection) , so only HDCP-compatible  
components can display the picture.  
Note  
• The HDMI video stream is compatible with DVI (Digital Visual  
Interface), so TVs and displays with a DVI input can be  
connected by using an HDMI-to-DVI adapter cable. (Note that  
DVI connections only carry video, so you’ll need to make a  
separate connection for audio.) However, reliable operation with  
such an adapter is not guaranteed. In addition, video signals from  
a PC are not supported.  
• The HDMI audio signal (sampling rate, bit length, etc.) may be  
restricted by the connected source component. If the picture is  
poor or there’s no sound from a component connected via HDMI,  
check its setup. Refer to the connected component’s instruction  
manual for details.  
The AV receiver’s HDMI interface is based on the  
following:  
Audio Return Channel, 3D, x.v.Color, DeepColor, Lip  
Sync, DTS-HD Master Audio, DTS-HD High  
Resolution Audio, Dolby TrueHD, Dolby Digital Plus,  
DSD and Multichannel PCM.  
En-62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Appendix  
Supported Audio File Formats  
USB Features  
For playback from a USB device, the AV receiver supports  
the following music file formats.  
USB Device Requirements  
Variable bit-rate (VBR) files are supported. However,  
playback time may not be display correctly.  
• USB mass storage device class (but not always  
guaranteed).  
• FAT16 or FAT32 file system format.  
• Up to 255 folders can be displayed, and folders may be  
nested up to 8 levels deep.  
• USB hubs and USB devices with hub functions are not  
supported.  
MP3 (.mp3 or .MP3)  
• MP3 files must be MPEG-1/MPEG-2.5 Audio Layer 3  
format with a sampling rate of 8 kHz, 11.025 kHz,  
12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,  
48 kHz and bitrates of between 8 kbps and 320 kbps.  
Incompatible files cannot be played.  
Note  
WMA (.wma or .WMA)  
• If the media you connect is not supported, the message “No  
Storage” will be displayed.  
WMA stands for Windows Media Audio and is an audio  
compression technology developed by Microsoft  
Corporation. Audio can be encoded in WMA format by  
• If you connect a USB hard disk drive to the AV receiver’s USB  
port, we recommend that you use its AC adapter to power it.  
• The AV receiver supports USB MP3 players that support the  
USB Mass Storage Class standard, which allows USB devices to  
be connected to computers without the need for special drivers or  
software. Note that not all USB MP3 players support the USB  
Mass Storage Class standard. Refer to your USB MP3 player’s  
instruction manual for details.  
®
using Windows Media Player.  
• WMA files must have the copyright option turned off.  
• Sampling rates of 32 kHz, 44.1 kHz, 48 kHz, bitrates of  
between 48 kbps and 320 kbps are supported.  
• WMA DRM/Pro/Voice formats are not supported.  
• Protected WMA music files on an MP3 player cannot be played.  
• Onkyo accepts no responsibility whatsoever for the loss or  
damage to data stored on a USB device when that device is used  
with the AV receiver. We recommend that you back up your  
important music files beforehand.  
AAC (.aac/.m4a/.mp4/.AAC/.M4A or .MP4)  
AAC stands for MPEG-2/MPEG-4 Audio.  
• Sampling rates of 16 kHz, 22.05 kHz, 24 kHz, 32 kHz,  
44.1 kHz, 48 kHz and bitrates of between 8 kbps and  
320 kbps are supported.  
• MP3 players containing music files that are managed with special  
music software are not supported.  
• Operation is not guaranteed for all USB devices, which includes  
the ability to power them.  
• Do not connect your USB device via a USB hub. The USB device  
must be connected directly to the AV receiver’s USB port.  
• If the USB device contains a lot of data, the AV receiver may take  
a while to read it.  
FLAC (.flac or .FLAC)  
FLAC is a file format for lossless audio data compression.  
• Sampling rates of 32 kHz, 44.1 kHz and 48 kHz are  
supported.  
• Quantization bit: 16 bit, 24 bit  
• USB devices with security functions cannot be played.  
En-63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Appendix  
License and Trademark  
Information  
“x.v.Color” is a trademark of Sony Corporation.  
Manufactured under license under U.S. Patent Nos: 5,956,674;  
5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929;  
7,392,195; 7,272,567 & other U.S. and worldwide patents issued  
& pending. DTS-HD, the Symbol, & DTS-HD and the Symbol  
together are registered trademarks of DTS, Inc. Product includes  
software. © DTS, Inc. All Rights Reserved.  
Manufactured under license from Dolby Laboratories. Dolby,  
Pro Logic and the double-D symbol are trademarks of Dolby  
Laboratories.  
Music Optimizer™ is a trademark of Onkyo Corporation.  
“HDMI, the HDMI Logo, and High-Definition Multimedia  
Interface are trademarks or registered trademarks of  
HDMI Licensing LLC in the United States and other countries.”  
iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and  
iPod touch are trademarks of Apple Inc., registered in the U.S.  
and other countries.  
“Made for iPod” and “Made for iPhone” mean that an electronic  
accessory has been designed to connect specifically to iPod or  
iPhone, respectively, and has been certified by the developer to  
meet Apple performance standards. Apple is not responsible for  
the operation of this device or its compliance with safety and  
regulatory standards.  
Please note that the use of this accessory with iPod or iPhone  
may affect wireless performance.  
En-64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Appendix  
HDMI  
Video Section  
Specifications  
Amplifier Section  
Input  
Output  
Video Resolution  
Audio Format  
IN 1, IN 2, IN 3, IN 4  
Input Sensitivity/Output Level and Impedance  
OUT  
1 Vp-p/75 (Component Y)  
1080p  
0.7 Vp-p/75 (Component PB/CB, PR/CR)  
Dolby TrueHD, DTS-HD Master Audio,  
DVD-Audio, DSD  
1 Vp-p/75 (Composite)  
Component Video Frequency Response  
5 Hz - 100 MHz/+0 dB, -3 dB  
Rated Output Power  
All channels:  
(North American and Brazilian)  
Supported  
3D, Audio Return Channel, DeepColor,  
x.v.Color, LipSync, CEC (RIHD)  
110 watts minimum continuous power per  
channel, 6 ohm loads, 1 channel driven at  
1 kHz, with a maximum total harmonic  
distortion of 1% (FTC)  
Tuner Section  
Video Inputs  
(Asian)  
6 ch × 100 W at 6 ohms, 1 kHz,  
1 ch driven of 1 % (IEC)  
Component  
Composite  
IN 1, IN 2  
FM Tuning Frequency Range  
(North American and Brazilian)  
BD/DVD, VCR/DVR, CBL/SAT, GAME,  
AUX  
Maximum Effective Output Power  
(Asian)  
87.5 MHz - 107.9 MHz  
(Asian)  
87.5 MHz - 108.0 MHz, RDS  
6 ch × 120 W at 6 ohms, 1 kHz, 1 ch driven  
(JEITA)  
Video Outputs  
AM Tuning Frequency Range  
*
Dynamic Power  
Component  
Composite  
OUT  
522/530 kHz - 1611/1710 kHz  
40  
*
IEC60268-Short-term maximum output power  
MONITOR OUT, VCR/DVR OUT  
Preset Channel  
160 W (3 , Front)  
125 W (4 , Front)  
85 W (8 , Front)  
Audio Inputs  
Digital  
General  
THD+N (Total Harmonic Distortion+Noise)  
Optical: 2  
Coaxial: 1  
0.08% (20 Hz - 20 kHz, half power)  
60 (Front, 1 kHz, 8 )  
Input Sensitivity and Impedance (Unbalance)  
200 mV/47 k(LINE)  
Rated RCA Output Level and Impedance  
200 mV/2.2 k(REC OUT)  
Maximum RCA Output Level and Impedance  
2 V/2.2 k(REC OUT)  
Power Supply  
(North American and Brazilian)  
AC 120 V, 60 Hz  
Damping Factor  
Analog  
BD/DVD, VCR/DVR, CBL/SAT, GAME,  
TV/CD, AUX  
(Asian) AC 220 - 240 V, 50/60 Hz  
Power Consumption (North American and Brazilian) 3.7 A  
(Asian) 370 W  
No-sound Power Consumption  
Audio Outputs  
(North American and Brazilian) 40 W  
(Asian)  
35 W (230 V)  
40 W (240 V)  
Analog  
Speaker Outputs  
Phones  
VCR/DVR  
SP-A (L, R, C, SL, SR, SW) + SP-B (L, R)  
1 (6.3 ø)  
Frequency Response 5 Hz - 100 kHz/+1 dB, –3 dB (DSP bypass)  
Tone Control Characteristics  
Stand-by Power Consumption  
Others  
10 dB, 50 Hz (BASS)  
10 dB, 20 kHz (TREBLE)  
(North American and Brazilian) 0.2 W  
(Asian) 0.3 W  
USB  
RI  
1 (Front)  
1
Signal to Noise Ratio 100 dB (LINE, IHF-A)  
Dimensions (W × H × D)  
Speaker Impedance  
6 - 16 Ω  
435 mm × 150 mm × 318 mm  
17-1/8" × 5-7/8" × 12-1/2"  
Weight  
(North American and Brazilian)  
7.6 kg (16.8 lbs.)  
(Asian)  
7.8 kg (17.2 lbs)  
Specifications and features are subject to change  
without notice.  
En-65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Appendix  
Memo  
En-66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Memo  
En-67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN  
Tel: 072-831-8023 Fax: 072-831-8163  
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.  
Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650  
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY  
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555  
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK  
Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700  
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.  
Tel: 852-2429-3118 Fax: 852-2428-9039  
1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,  
China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396  
Y1112-1  
SN 29401049  
(C) Copyright 2012 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved.  
* 2 9 4 0 1 0 4 9 *  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
E
n
5.1ch Home Theater Speaker Package  
HTP-391  
Surround speaker (SKR-391)  
Supplied Accessories  
Part Names  
Make sure you have the following accessories.  
Keyhole slot  
Front speaker (SKF-391)  
(Blue)  
(Gray)  
Speaker terminals  
Surround speakers  
Speaker cables 26 ft. (8.0 m)  
Subwoofer (SKW-391)  
SKF-391/SKR-391  
Speaker terminals  
(White)  
Speaker cables 10 ft. (3.0 m)  
(Red)  
Front speakers  
SKC-391/  
SKC-391C  
20 rubber stoppers*1  
(For Front/Center/  
Surround speakers)  
Keyhole slots  
(Purple)  
Subwoofer  
Speaker cable 10 ft. (3.0 m)  
Caution  
*1  
Configuration of the rubber stoppers may be different from the  
figure, such as being 2 sheets instead of 1 sheet, but the total  
number will be same.  
• The front grilles are not designed to be removed so do not  
attempt to remove them forcibly, as this will damage  
them.  
4 floor pads  
Center speaker (SKC-391/SKC-391C)  
Speaker terminals  
(Green)  
Center speaker  
Speaker cable 10 ft. (3.0 m)  
SKW-391  
SKC-391 (North American and Brazilian)  
SKC-391C (Asian)  
En-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
To mount the center speaker horizontally, use the two  
keyhole slots shown to hang the speaker on two screws that  
are securely screwed into the wall.  
Using the Floor Pads for Subwoofer  
Before Using the Home Theater  
Speaker Package  
If the subwoofer is placed on a hard floor (wood, vinyl,  
tile, etc.) and playback is very loud, the subwoofer’s feet  
may damage the flooring. To prevent this, place the  
supplied pads underneath the subwoofer’s feet. The pads  
also provide a stable base for the subwoofer.  
Keyhole slots for wall mounting  
Using the Rubber Stoppers for a More Stable  
Platform  
We recommend using the supplied rubber stoppers to  
achieve the best possible sound from your speakers. The  
rubber stoppers prevent the speakers from moving,  
providing a more stable platform.  
SKC-391/  
SKC-391C  
6-5/16" (160 mm)  
Pad  
Tip  
Rubber stoppers  
• If the center speaker is tilted, loosen the screw on the declined  
side to move upward so that the speaker could be adjusted  
vertically.  
Wall Mounting  
Bottom of the  
SKF-391/  
SKR-391  
Caution  
To mount the front/surround speakers vertically, use the  
keyhole slot shown to hang each speaker on a screw that’s  
securely screwed into the wall.  
• A mounting screw’s ability to support a  
speaker depends on how well it’s  
anchored to the wall. If you have  
hollow walls, screw each mounting  
screw into a stud. If there are no studs,  
or the walls are solid, use suitable wall  
anchors. Use screws with a head  
Wall  
Keyhole slot for  
wall mounting  
Rubber stoppers  
3/16" to 7/16"  
(5 to 10 mm)  
diameter of 5/16" (9 mm) or less and a shank diameter of  
1/8" (4 mm) or less. With hollow walls, use a cable/pipe  
detector to check for any power cables or water pipes  
before making any holes.  
• Leave a gap of between 3/16" (5 mm) and 7/16" (10 mm)  
between the wall and the base of the screw head, as  
shown (We recommend that you consult a home  
installation professional).  
1" (25 mm)  
SKF-391/SKR-391  
Bottom of the  
SKC-391/SKC-391C  
1-3/16" (30 mm)  
En-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
d b  
a
c
Enjoying Home Theater  
Connecting the Speakers  
The Home Theater means that you can enjoy surround  
sound with a real sense of movement in your own home —  
just like being in a movie theater or concert hall.  
Speaker Connection Precautions  
Read the following before connecting your speakers:  
• Turn off your receiver before making any connections.  
• Pay close attention to speaker wiring polarity.  
Connect positive (+) terminals to only  
a Front left and right speakers (SKF-391)  
They should be positioned facing the listener at about  
ear level, and equally spaced from the TV. Angle them  
inward slightly so as to create a triangle, with the  
listener at the apex.  
positive (+) terminals, and negative (–)  
terminals to only negative (–) terminals. If the  
speakers are wired incorrectly, the sound will be out of  
phase and will sound unnatural.  
• Be careful not to short the positive and negative wires.  
Doing so may damage your amp.  
b Center speaker (SKC-391/SKC-391C)  
Position it close to your TV (preferably on top) facing  
forward at about ear level, or at the same height as the  
front left and right speakers.  
Front right  
speaker  
Front left  
speaker  
c Surround left and right speakers (SKR-391)  
Position them at the sides of the listener, or slightly  
behind, about 2 to 3 feet (60 to 100 cm) above ear  
level. Ideally they should be equally spaced from the  
listener.  
Center speaker  
Red  
Green  
White  
d Subwoofer (SKW-391)  
Corner position  
The subwoofer handles the bass sounds of the LFE  
(Low-Frequency Effects) channel and bass from the  
satellite speakers when a crossover is specified. The  
volume and quality of the bass output from your  
subwoofer will depend on its position, the shape of  
your listening room, and your listening position. In  
general, a good bass sound can be obtained by  
installing the subwoofer in a front corner, or at one-  
third the way along the front wall, as shown.  
1/3 of wall position  
Purple  
Blue  
Subwoofer  
Gray  
Surround  
right  
Surround  
left  
speaker  
speaker  
En-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Center Speaker  
Surround Speakers (SKR-391)  
Specifications  
SKC-391 (North American and Brazilian)  
Type  
Impedance  
Maximum input power 120 W  
Sensitivity  
Frequency response  
Cabinet capacity  
Type  
Impedance  
Full Range Bass-reflex  
6  
Passive Subwoofer (SKW-391)  
Full Range Bass-reflex  
6 Ω  
Maximum input power 120 W  
Type  
Impedance  
Maximum input power 130 W  
Sensitivity  
Frequency response  
Cabinet capacity  
Dimensions (W × H × D) 11-5/8" × 13-9/16" × 14-1/2"  
(295 mm × 345 mm × 368 mm)  
Bass-reflex type Passive subwoofer  
6 Ω  
Sensitivity  
80 dB/W/m  
80 dB/W/m  
Frequency response  
Cabinet capacity  
80 Hz to 20 kHz  
80 Hz to 20 kHz  
0.039 cubic feet (1.1 L)  
83 dB/W/m  
0.064 cubic feet (1.8 L)  
Dimensions (W × H × D) 4" × 7-7/8" × 4-1/2"  
30 Hz to 150 Hz  
(101 mm × 200 mm × 114 mm)  
Dimensions (W × H × D) 9-7/16" × 4" × 4-3/4"  
0.88 cubic feet (25 L)  
(incl. grille and projection)  
1.5 lbs. (0.7 kg)  
(240 mm × 102 mm × 121 mm)  
(incl. grille and projection)  
1.8 lbs (0.8 kg)  
Weight  
Weight  
Drivers unit  
Terminal  
Keyhole slot  
Grille  
3-1/4" (8 cm) Cone × 1  
Spring type color coded  
Available  
(incl. projection)  
Drivers unit  
Terminal  
Keyhole slot  
Grille  
3-1/4" (8 cm) Cone × 1  
Spring type color coded  
Available  
Weight  
14.1 lbs. (6.4 kg)  
Drivers unit  
Terminal  
Other  
8" (20 cm) Cone × 1  
Spring type color coded  
Non-magnetic shielding  
Fixed  
Fixed  
Other  
Non-magnetic shielding  
Other  
Non-magnetic shielding  
Specifications and appearance are subject to change  
without prior notice.  
Front Speakers (SKF-391)  
SKC-391C (Asian)  
Type  
Impedance  
Maximum input power 120 W  
Sensitivity  
Frequency response  
Cabinet capacity  
Dimensions (W × H × D) 9-7/16" × 4" × 4-3/4"  
Type  
Impedance  
Maximum input power 120 W  
Sensitivity  
Frequency response  
Cabinet capacity  
Dimensions (W × H × D) 4" × 7-7/8" × 4-1/2"  
(101 mm × 200 mm × 114 mm)  
Full Range Bass-reflex  
6 Ω  
Full Range Closed Box  
Note  
6 Ω  
For non-magnetic shielded speakers:  
80 dB/W/m  
Try moving the speakers away from your TV or monitor. If  
discoloration should occur, turn off your TV or monitor,  
wait 15 to 30 minutes, and then turn it back on again. This  
normally activates the degaussing function, which  
neutralizes the magnetic field, thereby removing any  
discoloration effects.  
84.5 dB/W/m  
80 Hz to 20 kHz  
80 Hz to 20 kHz  
0.039 cubic feet (1.1 L)  
0.064 cubic feet (1.8 L)  
(240 mm × 102 mm × 121 mm)  
(incl. grille and projection)  
2.9 lbs (1.3 kg)  
(incl. grille and projection)  
Weight  
1.5 lbs (0.7 kg)  
Weight  
Drivers unit  
Terminal  
Keyhole slot  
Grille  
3-1/4" (8 cm) Cone × 1  
Spring type color coded  
Available  
Drivers unit  
Terminal  
Keyhole slot  
Grille  
3-1/4" (8 cm) Cone × 2  
Spring type color coded  
Available  
Fixed  
Fixed  
Other  
Non-magnetic shielding  
Other  
Magnetic shielding  
En-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
F
r
Ensemble d’enceintes du Home cinéma 5.1 can.  
HTP-391  
Enceinte surround (SKR-391)  
Accessoires fournis  
Noms des pièces  
Assurez-vous que le carton contient bien les accessoires  
suivants.  
Encoche en trou  
de serrure  
Enceinte avant (SKF-391)  
(Bleu)  
(Gris)  
Bornes d’enceinte  
Enceintes surround  
Câbles d’enceinte 8,0 m  
Subwoofer (SKW-391)  
SKF-391/SKR-391  
Bornes d’enceinte  
(Blanc)  
Câbles d’enceinte 3,0 m  
(Rouge)  
Enceintes avant  
SKC-391/  
SKC-391C  
Encoches en trou de serrure  
20 bouchons de  
caoutchouc*1  
(Pour enceintes avant/  
centrale/surround)  
(violet)  
Subwoofer  
Câble d’enceinte 3,0 m  
Mise en garde  
• Les grilles avant ne sont pas faites pour être retirées, aussi  
n’essayez pas de les retirer de force, car ceci les  
endommagera.  
*1  
La configuration des bouchons de caoutchouc peut être  
différente de la figure, en comportant par exemple 2 feuilles au  
lieu d’une, mais leur nombre total est identique.  
4 tampons de protection  
Enceinte centrale (SKC-391/SKC-391C)  
Bornesd’enceinte  
(Vert)  
SKW-391  
Enceinte centrale  
Câble d’enceinte 3,0 m  
SKC-391 (Nord-américains et brésiliens)  
SKC-391C (Asie)  
Fr-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Pour fixer l’enceinte centrale de façon horizontale, utilisez  
les deux encoches en trou de serrure indiquées pour  
accrocher l’enceinte à deux vis bien fixées au mur.  
Utilisation des tampons de protection pour  
le subwoofer  
Avant d’utiliser l’Ensemble d’enceintes  
du Home cinéma  
Si le subwoofer est placé sur un sol dur (bois, vinyle,  
carrelage, etc.) et si le niveau sonore de la lecture est élevé,  
les pieds du subwoofer peuvent endommager le sol. Pour  
empêcher ceci, placez les tampons fournis sous les pieds  
du subwoofer. Les tampons fournissent également une base  
stable au subwoofer.  
Encoche en trou de serrure pour la fixation au mur  
Utilisation des bouchons en caoutchouc  
pour une meilleure stabilité  
Nous vous recommandons d’utiliser les bouchons en  
caoutchouc fournis pour obtenir le meilleur son possible de  
vos enceintes. Les bouchons en caoutchouc empêchent les  
enceintes de bouger, en procurant une meilleure stabilité.  
SKC-391/  
SKC-391C  
160 mm  
Conseil  
Bouchons de caoutchouc  
• Si l’enceinte centrale est inclinée, dévissez la vis du côté incliné  
pour régler la position verticale de l’enceinte et la redresser.  
Tampon  
Dessous de  
la SKF-391/  
SKR-391  
Mise en garde  
• La capacité de la vis de fixation  
permettant de supporter une enceinte  
dépend de la façon dont elle est fixée  
au mur. Si vos murs sont creux, vissez  
chaque vis de fixation dans un montant.  
S’il n’y a aucun montant, ou si les murs  
sont pleins, utilisez des fixations  
murales adéquates. Utilisez des vis dont la tête a un  
diamètre de 9 mm maximum et un diamètre de la partie  
lisse de la tige de 4 mm maximum. Pour les murs creux,  
utilisez un détecteur de câbles/canalisations pour vérifier  
la présence éventuelle de câbles d’alimentation ou de  
canalisations d’eau avant d’effectuer des percements.  
• Laissez un espace de 5 à 10 mm entre le mur et la base de  
la tête de la vis, comme indiqué (Nous vous  
Mur  
Fixation au mur  
Pour fixer les enceintes avant/surround de façon verticale,  
utilisez l’encoche en trou de serrure pour accrocher chaque  
enceinte sur une vis bien vissée au mur.  
5 à 10 mm  
Bouchons de caoutchouc  
Encoche en trou  
de serrure pour la  
fixation au mur  
25 mm  
Bas de la  
SKC-391/SKC-391C  
30 mm  
SKF-391/SKR-391  
recommandons de consulter un professionnel de  
l’installation domestique).  
Fr-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
d b  
a
c
Vivez une expérience  
Branchement des enceintes  
cinématographique à domicile  
Précautions concernant le branchement des  
enceintes  
Grâce au Home Cinema, vous pouvez profiter d’un son  
surround très réaliste à votre domicile — comme si vous  
étiez dans une salle de cinéma ou de concert.  
Lisez ce qui suit avant de brancher vos enceintes :  
Éteignez votre récepteur avant d’effectuer les branchements.  
Faites très attention à respecter la polarité des  
câbles de vos enceintes. Ne branchez les bornes  
positives (+) que sur les bornes positives (+) et les  
bornes négatives (–) que sur les bornes négatives  
(–). Si les enceintes sont branchées de façon  
a Enceintes avant gauche et droite (SKF-391)  
Elles doivent être positionnées face à l’auditeur, à la  
hauteur des oreilles et être situées à distance égale du  
téléviseur. Orientez-les légèrement vers l’intérieur de  
manière à créer un triangle avec l’auditeur.  
b Enceinte centrale (SKC-391/SKC-391C)  
Positionnez-la à proximité de votre téléviseur (de  
préférence dessus), face à vous, à la hauteur des  
oreilles ou à la même hauteur que les enceintes avant  
gauche et droite.  
incorrecte, le son sera déphasé et ne semblera pas naturel.  
• Veillez à ne pas mettre ne pas mettre les fils positifs et  
négatifs en court-circuit. Vous risqueriez d’endommager  
votre amplificateur.  
Enceinte  
Enceinte  
c Enceintes surround gauche et droite (SKR-391)  
Placez-les sur les côtés de l’auditeur, ou légèrement  
derrière lui, 60 à 100 cm environ au-dessus du niveau  
des oreilles. Idéalement, elles doivent se situer à égale  
distance de l’auditeur.  
avant droite  
avant gauche  
Enceinte centrale  
Position  
angulaire  
Rouge  
Vert  
Blanc  
d Subwoofer (SKW-391)  
Le subwoofer gère les graves du canal chargé des effets  
LFE (effets basse fréquence) et les graves des enceintes  
satellites lorsqu’un crossover est spécifié. Le volume et  
la qualité des sons graves émis par le subwoofer  
dépendent de sa position, de la forme de la pièce où le  
système est installé et de votre position d’écoute. En  
général, il est possible d’obtenir un bon son grave en  
installant le subwoofer dans un coin situé devant  
l’auditeur ou à environ un tiers de la largeur du mur (cf.  
illustration).  
1/3 de la position murale  
Violet  
Bleu  
Subwoofer  
Gris  
Enceinte  
surround  
droite  
Enceinte  
surround  
gauche  
Fr-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Enceinte centrale  
Enceintes surround (SKR-391)  
Caractéristiques techniques  
SKC-391 (Nord-américains et brésiliens)  
Type  
Impédance  
Type  
Impédance  
Bass-reflex à large bande  
6 Ω  
Subwoofer passif (SKW-391)  
Bass-reflex à large bande  
6 Ω  
Puissance d’entrée maximale  
120 W  
80 dB/W/m  
Distorsion de fréquence 80 Hz à 20 kHz  
Type  
Impédance  
Subwoofer passif de type bass-reflex  
6 Ω  
Puissance d’entrée maximale  
120 W  
80 dB/W/m  
Distorsion de fréquence 80 Hz à 20 kHz  
Sensibilité  
Puissance d’entrée maximale  
130 W  
83 dB/W/m  
Distorsion de fréquence 30 Hz à 150 Hz  
Sensibilité  
Capacité du coffrage  
0,039 pieds cubiques (1,1 L)  
Sensibilité  
Capacité du coffrage  
Dimensions (L × H × P) 9-7/16" × 4" × 4-3/4"  
0,064 pieds cubiques (1,8 L)  
Dimensions (L × H × P) 4" × 7-7/8" × 4-1/2"  
(101 mm × 200 mm × 114 mm)  
Capacité du coffrage  
0,88 pieds cubiques (25 L)  
(y compris la grille et la projection)  
1,5 lbs. (0,7 kg)  
(240 mm × 102 mm × 121 mm)  
(y compris la grille et la projection)  
1,8 lbs (0,8 kg)  
Dimensions (L × H × P) 11-5/8" × 13-9/16" × 14-1/2"  
(295 mm × 345 mm × 368 mm)  
Poids  
Poids  
Amplificateur  
Borne  
Amplificateur  
Borne  
Cône de 3-1/4" (8 cm) × 1  
À ressort et à code couleur  
(y compris la projection)  
Cône de 3-1/4" (8 cm) × 1  
À ressort et à code couleur  
Poids  
14,1 lbs. (6,4 kg)  
Encoche en trou de serrure  
Amplificateur  
Borne  
Autre  
Cône de 8" (20 cm) × 1  
À ressort et à code couleur  
Protection non-magnétique  
Encoche en trou de serrure  
Disponible  
Disponible  
Grille  
Autre  
Fixe  
Grille  
Autre  
Fixe  
Protection non-magnétique  
Protection non-magnétique  
Enceintes avant (SKF-391)  
Les caractéristiques techniques et l’apparence de cet  
appareil sont susceptibles d’être modifiées sans préavis.  
Type  
Impédance  
Bass-reflex à large bande  
6 Ω  
SKC-391C (Asie)  
Type  
Impédance  
Large Bande à Coffrage Fermé  
Remarque  
Puissance d’entrée maximale  
120 W  
80 dB/W/m  
Distorsion de fréquence 80 Hz à 20 kHz  
6 Ω  
Pour enceintes blindées non magnétiques :  
Essayez d’éloigner les enceintes de votre téléviseur ou de  
votre moniteur. Si une décoloration se produit, éteignez  
votre téléviseur ou votre moniteur, attendez 15 à 30  
minutes, puis rallumez le téléviseur ou le moniteur. Ceci  
active normalement la fonction de démagnétisation, qui  
neutralise le champ magnétique, supprimant ainsi les effets  
de décoloration.  
Puissance d’entrée maximale  
120 W  
84,5 dB/W/m  
Distorsion de fréquence 80 Hz à 20 kHz  
Sensibilité  
Sensibilité  
Capacité du coffrage  
0,039 pieds cubiques (1,1 L)  
Dimensions (L × H × P) 4" × 7-7/8" × 4-1/2"  
Capacité du coffrage  
Dimensions (L × H × P) 9-7/16" × 4" × 4-3/4"  
0,064 pieds cubiques (1,8 L)  
(101 mm × 200 mm × 114 mm)  
(y compris la grille et la projection)  
(240 mm × 102 mm × 121 mm)  
(y compris la grille et la projection)  
2,9 lbs (1,3 kg)  
Poids  
1,5 lbs (0,7 kg)  
Amplificateur  
Borne  
Cône de 3-1/4" (8 cm) × 1  
À ressort et à code couleur  
Poids  
Amplificateur  
Borne  
Cône de 3-1/4" (8 cm) × 2  
À ressort et à code couleur  
Encoche en trou de serrure  
Disponible  
Encoche en trou de serrure  
Grille  
Autre  
Fixe  
Disponible  
Protection non-magnétique  
Grille  
Autre  
Fixe  
Protection magnétique  
Y1112-1  
SN 29400972  
(C) Copyright 2012 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved.  
* 2 9 4 0 0 9 7 2 *  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

Miele Food Warmer ESW 47XX User Manual
MTD Log Splitter 241 645A User Manual
Nady Systems Portable Speaker PCS 15 User Manual
Napoleon Fireplaces Outdoor Fireplace B36DFN User Manual
National Instruments Network Card NI 9401 User Manual
NEC Projector XT4100 User Manual
Omnimount Indoor Furnishings G362 User Manual
Omron Switch B3F User Manual
ParaBody Home Gym 607 User Manual
ParaBody Home Gym 872101 User Manual