Onkyo Computer Drive BR925 User Manual

Contents

Getting Started ..............................2

CD/HDD Receiver

BR-925

Instruction Manual

Connections ................................15

Turning On & First Time Setup ..22

Basic Operation...........................24

Playing & Listening

Playing CDs..............................28

Listening to the Radio...............32

USB Device Playback...............41

Playing External Components ..45

Recording (Transferring Data) ...46

Playing the HDD ..........................54

Clock and Timer ..........................62

Advanced Setup ..........................68

Others...........................................70

Thank you for purchasing an Onkyo CD/HDD

receiver.

Please read this manual thoroughly before making

any connections and plugging it in.

Following the instructions in this manual will enable

you to obtain optimum performance and listening

enjoyment from your new CD/HDD receiver.

Please retain this manual for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions

1. Recording Copyright—Unless it’s for personal use

only, recording copyrighted material is illegal with-

out the permission of the copyright holder.

9. Installing this Unit

• Install this unit in a well-ventilated location.

• Ensure that there’s adequate ventilation all

around this unit, especially if it’s installed in an

audio rack. If the ventilation is inadequate, the

unit may overheat, leading to malfunction.

• Do not expose this unit to direct sunlight or heat

sources, because its internal temperature may

rise, shortening the life of the optical pickup.

• Avoid damp and dusty places, and places subject

to vibrations from loudspeakers. Never put the

unit on top of, or directly above a loudspeaker.

• Install this unit horizontally. Never use it on its

side or on a sloping surface, because it may cause

a malfunction.

2. AC Fuse—The AC fuse inside the unit is not user-

serviceable. If you cannot turn on the unit, contact

your Onkyo dealer.

3. Care—Occasionally you should dust the unit all

over with a soft cloth. For stubborn stains, use a soft

cloth dampened with a weak solution of mild deter-

gent and water. Dry the unit immediately afterwards

with a clean cloth. Don’t use abrasive cloths, thin-

ners, alcohol, or other chemical solvents, because

they may damage the finish or remove the panel let-

tering.

4. Power

• If you install this unit near a TV, radio, or VCR,

the picture and sound quality may be affected. If

this occurs, move this unit away from the TV,

radio, or VCR.

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SEC-

TION CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the

voltage requirements printed on the unit’s rear panel

(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

10. Moisture Condensation

Moisture condensation may damage this unit.

Read the following carefully:

Moisture may condense on the lens of the optical

pickup, one of the most important parts inside this

unit.

The power cord plug is used to disconnect this unit

from the AC power source. Make sure that the plug

is readily operable (easily accessible) at all times.

• Moisture condensation can occur in the following

situations:

– The unit is moved from a cold place to a warm

place.

– A heater is turned on, or cold air from an air

conditioner is hitting the unit.

5. Preventing Hearing Loss

Caution

Excessive sound pressure from earphones and head-

phones can cause hearing loss.

– In the summer, when this unit is moved from

an air conditioned room to a hot and humid

place.

– The unit is used in a humid place.

• Do not use this unit when there’s the possibility

of moisture condensation occurring. Doing so

may damage your discs and certain parts inside

this unit.

If condensation does occur, remove all discs and

leave this unit turned on for two to three hours. By

this time, the unit will have warmed up and any con-

densation will have evaporated.

6. Batteries and Heat Exposure

Warning

Batteries (battery pack or batteries installed) shall

not be exposed to excessive heat as sunshine, fire or

the like.

7. Never Touch this Unit with Wet Hands—Never

handle this unit or its power cord while your hands

are wet or damp. If water or any other liquid gets

inside this unit, have it checked by your Onkyo

dealer.

8. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you origi-

nally bought it.

• Do not leave rubber or plastic items on this unit

for a long time, because they may leave marks on

the case.

• This unit’s top and rear panels may get warm

after prolonged use. This is normal.

• If you do not use this unit for a long time, it may

not work properly the next time you turn it on, so

be sure to use it occasionally.

• When you’ve finished using this unit, remove all

discs and turn off the power.

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions—Continued

This unit contains a semiconductor laser system and is

classified as a “CLASS 1 LASER PRODUCT”. So, to

use this model properly, read this Instruction Manual

carefully. In case of any trouble, please contact the store

where you purchased the unit.

For British models

Replacement and mounting of an AC plug on the power

supply cord of this unit should be performed only by

qualified service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance

with the following code:

To prevent being exposed to the laser beam, do not try to

open the enclosure.

CAUTION:

Blue: Neutral

Brown: Live

CLASS 1M VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN. DO NOT VIEW

DIRECTLY WITH OPTICAL INSTRUMENTS.

THIS PRODUCT UTILIZES A LASER. USE OF CON-

TROLS OR ADJUSTMENTS OR PERFORMANCE

OF PROCEDURES OTHER THAN THOSE SPECI-

FIED HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

As the colours of the wires in the mains lead of this appa-

ratus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to

the terminal which is marked with the letter N or

coloured black.

The wire which is coloured brown must be connected to

the terminal which is marked with the letter L or

coloured red.

The label on the right is

applied on the rear panel.

IMPORTANT

The plug is fitted with an appropriate fuse. If the fuse

needs to be replaced, the replacement fuse must

approved by ASTA or BSI to BS1362 and have the same

ampere rating as that indicated on the plug. Check for the

ASTA mark or the BSI mark on the body of the fuse.

If the power cord’s plug is not suitable for your socket

outlets, cut it off and fit a suitable plug. Fit a suitable fuse

in the plug.

1. This unit is a CLASS 1 LASER PRODUCT and

employs a laser inside the cabinet.

2. To prevent the laser from being exposed, do not

remove the cover. Refer servicing to qualified per-

sonnel.

For European Models

Declaration of Conformity

We,

ONKYO EUROPE

ELECTRONICS GmbH

LIEGNITZERSTRASSE 6,

82194 GROEBENZELL,

GERMANY

declare in own responsibility, that the ONKYO product

described in this instruction manual is in compliance with the

corresponding

technical standards such as EN60065,

EN55013, EN55020 and EN61000-3-2, -3-3.

GROEBENZELL, GERMANY

K. MIYAGI

ONKYO EUROPE ELECTRONICS GmbH

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

Supplied Accessories

Make sure you have the following accessories:

HDD/Amplifier

• 80 GB Hard Disk Capacity for Storing Audio Files

(Copies from CDs or a USB Mass Storage Device)

• Discrete Output Stage Circuitry

• Optimum Gain Volume Circuitry

• Dynamic Range Control

• Super Bass (On/Off) and Tone Control

Remote controller and two batteries (R6/AA)

Processing and Connection

• VLSC (Vector Linear Shaping Circuitry)

• Gracenote Database Capability

• Wolfson 2ch Audio D/A Converter

Indoor FM antenna

(Connector type varies from country to country.)

™

• Audyssey EQ to Correct Room Acoustic Problems

™*2

• Audyssey Dynamic EQ

• USB Port for iPod

Loudness Correction

®*3

or USB Mass Storage Device

• Optical Digital Input

• 3 Audio Inputs and 2 Outputs

• Subwoofer Pre Out

Others

AM loop antenna

• Plays Audio CDs, MP3s and WMA (via USB, CD-

R, CD-RW ); AAC and WAV Files (via USB)

• 4-Mode Timer (Play or Rec/Once or Every)

• Headphone Jack

In catalogs and on packaging, the letter at the end of the product

name indicates the color. Specifications and operations are the

same regardless of color.

• Aluminium Top Panel and Volume Knob

• RI-Dock Compatible Remote Control (iPod Control

Capable)

*1 VLSC and the VLSC logo are registered trademarks of Onkyo

Corporation.

Manufactured under license from Audyssey Laboratories. U.S.

™

and foreign patents pending. Audyssey Dynamic EQ and

™

Audyssey EQ are trademarks of Audyssey Laboratories.

*3 iPod is a trademark of Apple Inc., registered in the U.S. and

other countries.

*4 Windows Media, and the Windows logo are trademarks, or reg-

istered trademarks of Microsoft Corporation in the United States

and/or other countries.

*5 Make sure to use discs that have been finalized.

*6 The “AAC” logo is trademark of Dolby Laboratories.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before Using the CD/HDD Receiver

Installing the Batteries

Using the Remote Controller

When you operate the remote controller, point it at the

CD/HDD receiver’s remote control sensor, as shown

below.

Detach the battery cover by pressing the

tab and pulling up the cover.

Remote control sensor

Insert two batteries (R6/AA) into the bat-

tery compartment.

CD/HDD receiver

Carefully follow the polarity diagram (positive

(+) and negative (–) symbols) inside the battery

compartment.

Notes:

• The remote controller may not work reliably if the CD/

HDD receiver is subjected to bright light, such as direct

sunlight or inverter-type fluorescent lights. Keep this in

mind when installing.

• If another remote controller of the same type is used in

the same room, or the CD/HDD receiver is installed close

to equipment that uses infrared rays, the remote control-

ler may not work reliably.

• Don’t put anything, such as a book, on the remote con-

troller because the buttons may be pressed inadvertently,

thereby draining the batteries.

• The remote controller may not work reliably if the CD/

HDD receiver is installed in a rack behind colored glass

doors. Keep this in mind when installing.

• The remote controller will not work if there’s an obstacle

between it and the CD/HDD receiver’s remote control

sensor.

After the batteries are installed and

seated correctly, attach the compartment

cover.

Notes:

• If the remote controller doesn’t work reliably, try replac-

ing the batteries.

• Don’t mix new and old batteries or different types of bat-

teries.

• If you intend not to use the remote controller for a long

time, remove the batteries to prevent damage from leak-

age or corrosion.

• Expired batteries should be removed as soon as possible

to prevent damage from leakage or corrosion.

• When replacing the batteries, use R6/AA batteries.

Onkyo recommend that you use manganese dry batteries.

• If rechargeable batteries are used, the remote controller

may be inoperable.

Download from Www.Somanuals.com. All Manuals Search And Download.

What You Can Do with the CD/HDD Receiver

Connected

Components

CDs

Radio

Playing CDs (page 28)

Playing an external component (page 45)

Listening to the radio (page 32)

Recording CDs (page 48)

Recording from an external component (page 50) Recording the radio (page 50)

Transferring the data (page 51)

USB mass

storage device^*1

HDD

(Hard Disk Drive)

Playing iPod^®

thru USB port

(page 42)

Accessing

Digital audio

from PC^*2

player^*1

(page 52)

Playing music from USB device (page 42)

Transferring the data (page 51)

*1 Only for USB devices supporting the USB mass storage class.

*2 Only for personal computers with Microsoft Windows XP Service Pack 2, Service Pack 3, or Microsoft Windows Vista installed.

Download from Www.Somanuals.com. All Manuals Search And Download.

What You Can Do with the CD/HDD Receiver—Continued

Handling the Hard Disk Drive (HDD)

The HDD is very sensitive to physical shock, vibration, and dust.

The CD/HDD receiver is designed to protect the data safely from physical shock, vibration, and dust. However, pay

particular attention to the following points to prevent the recorded data from being lost.

• Do not apply physical shock.

• Do not move the CD/HDD receiver with power cord plugged.

• Do not use the CD/HDD receiver in vibratory or unstable place.

• Do not unplug or move the CD/HDD receiver during recording or playback.

• Do not attempt to replace the HDD or to add another one by yourself. A failure may occur.

• Do not install the CD/HDD receiver in a dusty place.

• Do not block any ventilation openings on the CD/HDD receiver. Heat may be built up, causing a failure.

• Do not use in a place with rapid temperature change (a change over 10°C per hour).

When there is the possibility of moisture condensation occurring, Onkyo recommend that you wait for approx.

one hour after turning the power on before using the CD/HDD receiver.

Advice on data backup

The HDD may fail even in normal use, for example, a sudden data loss or failure caused by electrical service interrup-

tion. If the HDD fails for some reason, the data cannot be restored. Onkyo recommend that you backup the data stored

in the CD/HDD receiver to your personal computer or commercially available USB hard disk drive periodically.

When getting repaired

When the HDD gets repaired, the data in the HDD of the CD/HDD receiver, including music data, setting data, cannot

sometimes be reproduced. Before it gets repaired, note down the setting details preset in the CD/HDD receiver on paper.

Also be sure to backup the data stored in the CD/HDD receiver. Please note that Onkyo will not be responsible for

anything if the data should be erased or changed during the repair and normal use.

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

USB De vice Playback ............................................. 41

Compatible USB Devices .................................... 41

USB Device Folders and Files............................. 41

Basic Operations of Playback.............................. 42

Playing Selected Tracks...................................... 43

Switching the Display .......................................... 43

Repeat/Random Playback................................... 44

Playing External Components................................. 45

Playing External Components ............................. 45

Making an u Connection with Onkyo

Getting Started

Important Safety Instructions .................................... 2

Precautions ............................................................... 3

Features.................................................................... 5

Supplied Accessories................................................ 5

Before Using the CD/HDD Receiver ......................... 6

Installing the Batterie s ........................................... 6

Using the Remote Controlle r ................................. 6

What You Can Do with the CD/HDD Receiver.......... 7

Handling the Hard Disk Drive (HDD)..................... 8

Getting to Know the CD/HDD Receiver .................. 10

Front Panel.......................................................... 10

Display................................................................. 11

Rear Panel .......................................................... 12

Remote Controller ............................................... 13

Components...................................................... 45

Recording (Transferring Data)

Recording (Transferring Data)................................. 46

Compatible USB Devices .................................... 46

Preparation for Recording and Transferrin g ........ 46

Setting for Recording........................................... 47

Recording CDs .................................................... 48

Recording from Tuner.......................................... 50

Recording from Line Input ................................... 50

Transferring Data................................................. 51

Erasing Data from USB Device ........................... 53

Connections

Connections ............................................................ 15

About Connections.............................................. 15

Connecting Speaker s .......................................... 16

Connecting Antenna s .......................................... 17

Connecting Other Components........................... 19

Connecting a Subwoofer..................................... 20

Connecting a Component with a Digital Audio

Playing the HDD

Output............................................................... 20

Connecting a TV.................................................. 20

Hooking Up to the Internet .................................. 21

Playing the HDD...................................................... 54

Basic Operations of Playback.............................. 54

Playing Selected Track s ...................................... 55

Switching the Display .......................................... 56

Various Playback Modes..................................... 57

Editin g Tracks and Playlists in the HDD.................. 58

Erasing Music Track or Album............................. 58

Editing Track Information..................................... 58

Removing Tracks from the Playlis t ...................... 60

Editing a Playlist Name........................................ 61

Turning On & First Time Setup

Turning On the CD/HDD Receive r .......................... 22

First Time Setup...................................................... 23

Setting the Clock with the AccuClock Functio n ... 23

Basic Operation

Basic Operations..................................................... 24

Selecting the Input Source .................................. 24

Adjusting the Volume .......................................... 24

Using Headphones.............................................. 24

Adjusting the Tone .................................................. 25

Adjusting the Bass and Treble ............................ 25

Using the Super Bass Function........................... 25

Using the Direct Functio n .................................... 25

Muting the Sound ................................................ 25

Using Audyssey EQ™

Cloc k and Timer

Setting the Clock ..................................................... 62

Setting AccuClock to Use a Specific Station ....... 62

Setting the Clock Manually.................................. 63

Using the Timers ..................................................... 64

Using the Sleep Time r ......................................... 64

Using the Play Timer ........................................... 65

Using the Record Timer....................................... 66

and Audyssey Dynamic EQ™ .............................. 26

Operation of Music Data ......................................... 27

USB Devic e ......................................................... 27

HDD..................................................................... 27

Advanced Setup

Advanced Setu p ...................................................... 68

Network Configuratio n ......................................... 68

Others

Playing & Listening

Disc Notes............................................................... 70

Playable Formats .................................................... 72

Controlling External Components............................ 73

Troubleshooting....................................................... 74

Specifications .......................................................... 79

Trademark and Other Proprietary Notices .............. 80

Playing CDs ............................................................ 28

Basic Operations of Playback ............................. 28

Playing Selected Tracks...................................... 29

Switching the Display .......................................... 29

Retrieving Audio CD Information......................... 30

Random Playback ............................................... 31

Repeat Playback ................................................. 31

Listening to the Radio ............................................. 32

Tuning into AM/FM Radio Stations...................... 32

Displaying Radio Information .............................. 33

Receiving RDS.................................................... 33

Presetting FM Stations Automatically (Auto Preset).... 34

Presetting AM/FM Stations Manually .................. 35

Selecting Preset Stations .................................... 36

Editing Presets .................................................... 37

To reset the CD/HDD receiver, see page 74.

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting to Know the CD/HDD Receiver

Front Panel

7 89 bkblbm bn

The page numbers in parentheses show where you can find the main explanation for each item.

a Remote control sensor (6)

j Play/Pause [1/3] button (28)

Receives control signals from the remote controller.

Starts CD playback. Pressing it during playback

pauses playback.

b CD r HDD DUBBING button (48)

Used to record a CD into HDD. When pressed,

immediately starts recording all tracks.

k LIBRARY button (28)

Displays the list of tracks.

c CD r USB DUBBING button (48)

Used to record a CD into a digital audio player or

USB storage device. When pressed, immediately

starts recording all tracks.

l RETURN button

Returns to the previous menu level.

m y REC button (49)

Pressed to record into HDD, digital audio player, or

USB storage device.

d ON/STANDBY button (22)

Sets the CD/HDD receiver to On or Standby.

n MULTI JOG dial (24, 28, 36)

Selects a preset radio station or tracks of CD to be

played.

e STANDBY indicator (22)

Lights off when the power is on, and lights up in red

in Standby mode.

Selects an item for editing or setting. Pressed to

confirm each setting.

f PHONES jack (24)

This stereo minijack is for connecting a pair of ste-

o INPUT SELECTOR button (24)

reo headphones for private listening.

Used to select the input source.

g CD tray (28)

p VOLUME control (24)

The CD is loaded here.

This control is used to adjust the volume of the

CD/HDD receiver to “Min”, “1” through “41”,

“Max”.

h Stop [2] button (28)

Stops CD playback.

q Open/Close [0] button (28)

i USB port (42)

Used to open and close the disc tray.

A USB mass storage device, such as a USB flash

drive or MP3 music player, containing music files

can be plugged in here and the music files can be

selected and played through the CD/HDD receiver.

r Display

See “Display” on page 11.

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting to Know the CD/HDD Receiver—Continued

Display

2 3

6 7

89 bk

bl bm

a Play, pause and Rec 1/3/y REC

indicators

g Tuning indicators

AUTO:

Displays the playback and recording status.

Lights up when Auto Tuning is selected, and disap-

pears when Manual Tuning is selected.

b Input source indicators

Displays the input source for playback. During

recording, the indicator of the destination flashes.

Lights up when the CD/HDD receiver is tuned to a

radio station.

HDD:

CD:

Hard disk drive.

Audio CD or data CD.

USB device.

FM STEREO:

Lights up when the CD/HDD receiver is tuned to a

stereo FM station.

USB:

TUNER: FM or AM.

RDS:

LINE 1 to LINE3:

Lights up when the CD/HDD receiver is tuned to a

radio station that supports RDS (Radio Data Sys-

tem).

Connected components.

DIGITAL: Components connected via optical digi-

tal audio.

h DIRECT indicator

Lights up when the input signal is PCM.

The indicator flashes if the input signal

is digital but not PCM, or the CD/HDD

receiver is in “unlocked” state (the cable

is disconnected or the component is not

turned on).

Lights up when the Direct function is on.

i REMAIN indicator

Lights up when the remaining track time is being

displayed.

j TIMER indicators

Show the status of the timers.

c S.BASS indicator

TIMER:

Lights up when the Super Bass function is on.

Lights up when a timer has been programmed.

d Message area

1, 2, 3, 4:

Various information is displayed here, including

radio preset numbers, tuning frequency, current time,

volume level, sleep time, mode settings, and so on.

Light up when a timer has been programmed.

Lights up when a timer has been programmed for

recording.

e Playback mode indicators

Lights up when random playback

is selected.

RANDOM:

k SLEEP indicator

Lights up when the Sleep function has been set.

Lights up when repeat playback

is selected for all tracks.

REPEAT:

l MUTING indicator

Flashes while the CD/HDD receiver is muted.

Lights up when repeat playback

is selected for one track.

REPEAT 1:

m Dynamic EQ indicator

Lights up when the Audyssey Dynamic EQ™ has

been set.

BGM:

Lights up when BGM mode play-

back is selected (see page 57).

n File format indicators

f Jump mode indicators

Lights up when jump mode is

selected (see page 55).

Displays the format of playback and recording data.

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting to Know the CD/HDD Receiver—Continued

Rear Panel

1 2 3 4

Heat sink

9 bk

The page numbers in parentheses show where you can find the main explanation for each item.

a ETHERNET (21)

h u REMOTE CONTROL (19)

This socket is for connecting a broadband router

using a commercially available LAN cable.

This u (Remote Interactive) jack can be con-

nected to an u jack on another Onkyo component.

The CD/HDD receiver’s remote controller can then

be used to control that component. To use u, you

must make an analog audio connection (RCA)

between the CD/HDD receiver and the other com-

ponent.

b LINE 1 IN (20)

These terminals are for connecting audio output of

external devices such as TV or turntable with a

built-in phono equalizer.

c MD/TAPE (LINE 2) IN/OUT (19)

i FM ANTENNA (17)

These analog audio inputs and outputs are for con-

necting a recorder with an analog input and output,

such as a MiniDisc recorder or cassette deck.

This jack is for connecting an FM antenna.

j AM ANTENNA (17)

These push terminals are for connecting an AM

antenna.

d DOCK/CDR (LINE 3) IN/OUT (19)

This analog audio input and output are for connect-

ing an Onkyo RI Dock. The input and output can

also be connected to a CD recorder or recording

device.

k Power cord (22)

The power cord should be connected to a suitable

power source (plug type varies from country to

country).

e SPEAKERS (16)

These terminal posts are for connecting speakers.

See pages 15–21 for connection information.

f SUBWOOFER PRE OUT (20)

This jack is for connecting a powered active sub-

woofer.

Caution:

The heat sink is a device designed to disperse heat from

within the CD/HDD receiver. Do not to place objects

around the CD/HDD receiver and ensure that there is ade-

quate ventilation all around the CD/HDD receiver. If the

ventilation is inadequate, the CD/HDD receiver may over-

heat, leading to malfunction.

g OPTICAL DIGITAL IN (20)

This optical digital audio input can be used to con-

nect a component with an optical digital output,

such as a CD recorder, MD recorder, games con-

sole, satellite tuner, or personal computer. Use a

commercially available optical digital audio cable

(square) to make the connection.

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting to Know the CD/HDD Receiver—Continued

Remote Controller

The page numbers in parentheses show where you can

find the main explanation for each item.

a ON/STANDBY button (22)

This button is used to set the CD/HDD receiver to

On or Standby.

b SLEEP button (64)

Used to set the Sleep timer, which turns off the

CD/HDD receiver after a specified time.

c Alphabetic letters/Symbol ( )/Number (0

to >10) buttons (39, 58, 61)

Used to enter the name of the playlist, album, artist,

track or radio presets.

Numeric: Used to select the track you want to play.

Also used to set the clock manually and set the tim-

ers.

d PLAYLIST REG button (57)

Used to register music files in HDD to the playlist.

e Source selection buttons (24)

INPUT [q]/[w] buttons:

Used to switch the input source.

HDD 1 button*:

Switches to HDD for playback.

CD 1 button*:

Switches to CD for playback.

USB 1 button*:

Switches to USB for playback.

* These buttons also work in the Standby mode.

f BGM MODE 1 button (57)

Used to play tracks in HDD* in BGM mode. This

button also works in the Standby mode.

* Except for music files recorded from the FM/AM or

external components.

g LIBRARY button (28)

Displays the list of tracks.

h RETURN button

Returns to the previous display.

i Operation buttons (28, 32, 36, 73)

3: Pauses playback.

1: Starts playback.

2: Stops playback.

Fast Reverse/Fast Forward [5]/[4] and

TUNING [e]/[r] buttons:

Used to fast reverse or fast forward CD playback.

Can also be used with an Onkyo RI Dock, CD

recorder or MD recorder. Also used to tune the

radio frequency.

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting to Know the CD/HDD Receiver—Continued

Previous/Next [7]/[6] and PRESET

[e]/[r] buttons

cr OPEN/CLOSE [0] button (28)

Used to open and close the disc tray.

Used to select the previous or next track or radio

preset. Can also be used with an Onkyo RI Dock,

CD recorder or MD recorder. With an Onkyo cas-

sette deck, they work as fast reverse and fast for-

ward buttons.

cs RANDOM button (31)

Used to select random playback.

j PLAYLIST [q]/[w] buttons (57)

Plays the tracks on the playlist. Each time the button

is pressed, the selected playlist is switched and

playback starts.

k USB REC [y 3] button (49)

Used to record to your USB storage device.

l HDD REC [y 3] button (49)

Used to record to HDD.

m CLOCK CALL button (63)

Calls up the clock to display the day and time.

This button also works in the Standby mode.

n TIMER button (63, 64)

Used to set the timers and clock.

o CAPS button (39)

Used to select the character group.

p DIRECT button (25)

Used to switch to the Direct mode.

q TONE button (25)

Used to adjust the bass and treble.

r S.BASS button (25)

Sets the Super Bass function.

s CLEAR button (40)

Used to delete the input letters.

t MUTING button (25)

Mutes the output of the CD/HDD receiver.

u VOL [q]/[w] button (24)

Adjust the volume level.

v TUNER (BAND) button (36)

Selects AM or FM radio as the input source.

w TOOLS button

Used to display setting items.

x Cursor q/w/e/r and ENTER buttons

Cursor:

Selects items by moving the cursor.

ENTER:

Used to confirm settings. Also used to start play-

back of the selected track.

y DISPLAY button (29, 73)

Used to change the information shown on the dis-

play. With an Onkyo RI Dock, it works as a back-

light button.

z REPEAT button (31, 73)

Sets repeat playback. Can also be used with an

Onkyo RI Dock. With an Onkyo cassette deck, it

works as a reverse mode button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

About Connections

• Before making any connections, read the manuals

supplied with your other components.

• To prevent interference, keep audio cables away from

power cords and speaker cables.

• Don’t connect the power cord until you’ve completed

and double-checked all connections.

• If the TV picture is distorted, or noise is heard in the

output sound of the CD/HDD receiver, install the

CD/HDD receiver as far as possible from the TV.

Connection Color Coding

Optical Digital Input Terminal

RCA-type audio connections are usually color-coded:

red and white. Use red plugs to connect right-channel

audio inputs and outputs (typically labeled “R”). Use

white plugs to connect left-channel audio inputs and out-

puts (typically labeled “L”).

The optical digital input terminal of the CD/HDD

receiver is a type of terminal with cover. Insert the opti-

cal digital cable while pushing the cover inwards.

Notes:

• Plug or unplug the optical digital cable in straight direc-

tion.

• If you plug or unplug the cable slantingly, the cover may

be damaged.

Analogaudio

Left (white)

Right (red)

Left (white)

Right (red)

cable

• Do not put anything on top of the CD/HDD receiver, as it

may interfere with proper ventilation, leading to malfunc-

tion.

• Push plugs in all the way to make

good connections (loose connec-

tions can cause noise or malfunc-

tions).

Right!

Wrong!

See the related pages for connection.

Antennas

Speakers

page 17

page 16

Internet

page 21

Digital device

with an optical

digital output

such as a game

console, a per-

sonal computer,

or a satellite tuner

Powered active

subwoofer

page 20

Power cord

(Plug type varies from country to

country.)

Recording device such as an MD recorder, a

cassette deck or a CD recorder, or an Onkyo

RI dock

page 22

Don't connect the power cord

until you've completed and dou-

ble-checked all connections.

page 19

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections—Continued

Connecting Speakers

• Connect the right speaker to the CD/HDD receiver’s right (R) SPEAKERS terminals. Connect the left speaker to the

left (L) SPEAKERS terminals.

• Connect the positive (+) terminal on each speaker to the corresponding positive (+) terminal on the CD/HDD receiver.

Connect the negative (–) terminal on each speaker to the corresponding negative (–) terminal on the CD/HDD

receiver. Use the red wires to connect the positive (+) terminals.

• Up to two speakers can be connected to the CD/HDD receiver.

Left speaker

Right speaker

Red wires

Speaker cable

—Terminal posts—

Strip about 15 mm of insulation from the ends of the speaker

cables, and twist the bare wires tightly. Unscrew the terminal.

Fully insert the bare wire, making sure that it’s touching the

threaded shaft in the center. Screw the terminal tight.

• Connect only speakers with an impedance of between

4 and 16 ohms. Connecting a speaker with a lower

impedance may damage the speaker.

• Be careful not to confuse the positive and negative ter-

minals, or L and R speakers during the connection.

Doing so may result in unnatural sound.

• Be careful not to short the positive and negative wires.

Doing so may damage the CD/HDD receiver. Also, be

careful not to touch the rear panel.

• Do not connect both speaker cables to the same L or R

terminals (Fig. 1). Do not connect more than two

speaker terminals to each speaker (Fig. 2).

Fig. 1

Fig. 2

• Twist the speaker cord sufficiently.

The contact between bare wire and rear panel may

cause a short circuit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections—Continued

Connecting the AM Loop Antenna

Connecting Antennas

The supplied indoor AM loop antenna is for indoor use

only.

This section explains how to connect the supplied indoor

FM antenna and AM loop antenna, and how to connect

commercially available outdoor FM and AM antennas.

The CD/HDD receiver won’t pick up any radio signals

without an antenna connected, so you must connect the

antenna to use the tuner.

Assemble the AM loop antenna, inserting

the tabs into the base, as shown.

AM ANTENNA push terminals

FM ANTENNA jack

Connect both wires of the AM loop

antenna to the AM ANTENNA push termi-

nals, as shown.

(The antenna’s wires are not polarity sensitive, so

they can be connected either way around.)

Make sure that the wires are attached securely and

that the push terminals are gripping the bare

wires, not the insulation.

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.

Attach the FM antenna, as shown.

Push

Insert wire

Release

Insert the plug fully

into the jack.

Once the CD/HDD receiver is ready for use,

you’ll need to tune into an FM radio station and

adjust the position of the FM antenna to achieve

the best possible reception.

Once the CD/HDD receiver is ready for use,

you’ll need to tune into an AM radio station and

adjust the position of the AM antenna to achieve

the best possible reception.

Keep the antenna as far away as possible from the

CD/HDD receiver, TV, speaker cables, and power

cords.

Use thumbtacks or something similar to

fix the FM antenna into position.

If you cannot achieve good reception with the supplied

indoor AM loop antenna, try using it with a commer-

cially available outdoor AM antenna (see page 18).

Thumbtacks, etc.

Caution:

Be careful that you don’t injure yourself when using

thumbtacks.

If you cannot achieve good reception with the supplied

indoor FM antenna, try a commercially available out-

door FM antenna instead (see page 18).

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections—Continued

Connecting an Outdoor FM Antenna

Connecting an Outdoor AM Antenna

If you cannot achieve good reception with the supplied

indoor FM antenna, try a commercially available out-

door FM antenna instead.

If good reception cannot be achieved using the supplied

AM loop antenna, an outdoor AM antenna can be used

in addition to the loop antenna, as shown.

Outdoor antenna

AM loop antenna

Insulated antenna cable

Notes:

• Outdoor FM antennas work best outside, but usable

results can sometimes be obtained when installed in an

attic or loft.

• For best results, install the outdoor FM antenna well away

from tall buildings, preferably with a clear line of sight to

your local FM transmitter.

• Outdoor antenna should be located away from possible

noise sources, such as neon signs, busy roads, etc.

• For safety reasons, outdoor antenna should be situated

well away from power lines and other high-voltage

equipment.

Outdoor AM antennas work best when installed horizon-

tally outside, but good results can sometimes be obtained

indoors by mounting horizontally above a window. Note

that the AM loop antenna should be left connected.

Outdoor antenna must be grounded in accordance with

local regulations to prevent electrical shock hazards.

• Outdoor antenna must be grounded in accordance with

local regulations to prevent electrical shock hazards.

■ Using a TV/FM Antenna Splitter

It’s best not to use the same antenna for both FM and TV

reception, as this can cause interference problems. If cir-

cumstances demand it, use a TV/FM antenna splitter, as

shown.

TV/FM antenna splitter

To CD/HDD receiver

To TV (or VCR)

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections—Continued

Connecting Other Components

The following diagram shows how to connect other components (i.e., a cassette deck, an MD recorder, a CD recorder)

and an Onkyo RI Dock (Remote Interactive Dock). If Audyssey EQ™ is active, you cannot perform recording (except

for timer recording) to an external component. Deactivate Audyssey EQ™ when you want to record to an external

component (see page 26).

Connecting an MD recorder or cassette deck

Connect the CD/HDD receiver’s MD/TAPE OUT jacks to the INPUT (REC) jacks of the MD recorder or cassette deck.

Connect the CD/HDD receiver’s MD/TAPE IN jacks to the OUTPUT (PLAY) jacks of the MD recorder or cassette deck.

Connecting a CD recorder or an Onkyo RI Dock

Connect the CD/HDD receiver’s DOCK/CDR OUT jacks to the AUDIO INPUT jacks of the CD recorder or Onkyo RI

Dock.

Connect the CD/HDD receiver’s DOCK/CDR IN jacks to the AUDIO OUTPUT jacks of the CD recorder or Onkyo RI

Dock.

Connecting Onkyo u Components

First connect each Onkyo component to the CD/HDD receiver with an analog audio cable (RCA) as described above.

Next, make the necessary u connections with an u cable (see illustration below). Finally, change the Input Display

to the corresponding component name (see page 45).

MD recorder

Cassette deck

CD/HDD receiver’s rear panel

Analog audio

cables (RCA)

u cable sup-

plied with the

Onkyo RI Dock

CD recorder

Onkyo RI Dock

: Signal flow

u cable supplied with other Onkyo components

What can you do with u?

• Connecting an Onkyo u-capable component to the CD/HDD receiver via u cable allows you to control the com-

ponent with the CD/HDD receiver’s remote controller.

• When playback is started on the component connected via u, the CD/HDD receiver will automatically select it as

the input source.

• When you start playback on the component connected via u, if the CD/HDD receiver is on Standby, it will auto-

matically turn on. Similarly, when the CD/HDD receiver is set to Standby, all components connected via u will also

go on Standby.

Notes:

• No u cable is included with the CD/HDD receiver. Use u cables supplied with other Onkyo components.

• Use u jacks for a combined use with u-capable components.

• Some u-capable components have two u jacks. They’re both the same, so you can use either one. The extra jack is for

connecting additional u-capable components.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections—Continued

Connecting a Subwoofer

The CD/HDD receiver has SUBWOOFER PRE OUT jack for connecting a powered active subwoofer (i.e., a subwoofer

with a built-in amplifier).

Powered active

subwoofer

CD/HDD receiver’s rear panel

: Signal flow

Connecting a Component with a Digital Audio Output

The following diagram shows how to connect a component with an optical digital audio output, such as a games console,

satellite tuner, or personal computer. Connect the CD/HDD receiver’s DIGITAL OPTICAL IN jack to an optical digital

audio output on the other component.

You can change the Input Display for the OPTICAL DIGITAL IN to DIGITAL, CD-R/dig, GAME/dig, or PC/dig so

that it matches the type of component that you connect (see page 45).

The CD/HDD receiver supports only a 16-bit PCM signal with a sampling rate of between 44.1 kHz and 48 kHz.

Some components require the settings of forced conversion to PCM.

: Signal flow

Game console, etc.

Commercially available optical

digital audio cable (square)

DIGITAL

OUTPUT

Optical digital output

Connecting a TV

Connect the CD/HDD receiver’s LINE 1 IN jacks to the TV’s audio output jacks.

Red White

Analog audio cable (RCA)

Audio output

: Signal flow

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections—Continued

• The CD/HDD receiver does not support PPPoE settings,

so if you have a PPPoE-type Internet connection, you

must use a PPPoE-compatible router.

• Depending on your ISP, you may need to specify a proxy

server. If your computer is configured to use a proxy

server, use the same settings for the CD/HDD receiver

(see page 69).

Hooking Up to the Internet

The CD/HDD receiver is network-ready, which means

you can hook it up to your home network with a standard

Internet and the Gracenote music recognition service is

available. Gracenote music recognition service is

music CD database service constructed on servers

located on the Internet. See page 80 for details.

In addition, while the PC is accessing the CD/HDD

receiver, you can transfer the music files between the

CD/HDD receiver and your PC via FTP. See page 52 for

details.

The CD/HDD receiver is configured to automatically try

to access the Internet upon completion of the hook up. If

your connection is not successfully established, see

page 68. A contract with an Internet Service Provider

(ISP) is required to connect to the Internet. If you already

have a broadband internet connection there is no need to

take out another contract.

Connecting the CD/HDD receiver

To connect the CD/HDD receiver to your home network,

plug one end of a shielded CAT5 Ethernet cable into the

CD/HDD receiver’s ETHERNET port, and plug the

other end into a LAN port on your router or switch.

The following diagram shows how you can connect the

CD/HDD receiver to your home network. In this exam-

ple, it’s connected to a LAN port on a router, which has

a 4-port 100Base-TX switch built-in.

CD/HDD receiver

Network Requirements

■ Ethernet Network

The CD/HDD receiver’s Ethernet port supports 10Base-

T. For best results, a 100Base-TX switched Ethernet net-

work is recommended. Because wireless connections

may be unreliable, wired connections are recommended.

■ Ethernet Router

A router manages the network, routing data and supply-

ing IP addresses. Your router must support the following:

• NAT (Network Address Translation). NAT allows sev-

eral networked computers to access the Internet simul-

taneously via a single Internet connection.

• DHCP (Dynamic Host Configuration Protocol).

DHCP supplies IP addresses to network devices,

allowing them to configure themselves automatically.

• A router with a 100Base-TX switch built-in is recom-

mended.

Modem

WAN port

Router

LAN port

Some routers have a modem built-in, and some ISPs

require you to use specific routers. Please consult your

ISP or computer dealer if you’re unsure.

LAN/Ethernet port

■ CAT5 Ethernet cable

Use a shielded CAT5 Ethernet cable (straight-type) to

connect the CD/HDD receiver to your home network.

Computer

■ Internet Access

Music recognition technology and related data are pro-

vided by Gracenote . Gracenote is the industry standard

in music recognition technology and related content

delivery. For more information visit www.gracenote.com.

A narrowband Internet connection (e.g., 56K modem,

ISDN) will not provide satisfactory results, so a broad-

band connection is strongly recommended (e.g., cable

modem, xDSL modem, etc). Please consult your ISP or

computer dealer if you’re unsure.

Notes:

• The CD/HDD receiver uses DHCP to configure its net-

work settings automatically. If you want to configure

these settings manually, see page 69.

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On the CD/HDD Receiver

Plug the power cord into a suitable wall outlet.

The STANDBY indicator lights up after a while (several seconds). The CD/HDD receiver

enters the Standby mode.

Notes:

• Before connecting the power cord, connect all of your speakers and AV components.

• Turning on the CD/HDD receiver may cause a momentary power surge that might interfere with

other electrical equipment on the same circuit. If this is a problem, plug the CD/HDD receiver into

a different branch circuit.

To wall outlet

Power cord

(Plug type varies from country

to country.)

Press the [ON/STANDBY] button on the CD/HDD receiver or remote controller.

ON/STANDBY

STANDBY indicator

The STANDBY indicator goes off and the following screen appears on the display. Press the

[ON/STANDBY] button again to set the CD/HDD receiver to Standby. The STANDBY indi-

cator lights up.

Tip:

When you start playback on (or turn on) an Onkyo RI Dock, CD recorder, MD recorder, or cassette deck that’s connected to

the CD/HDD receiver with an u cable and analog audio cable, the CD/HDD receiver turns on automatically. Similarly, when

you set the CD/HDD receiver to On or Standby, the other component will also be set to On or Standby.

Download from Www.Somanuals.com. All Manuals Search And Download.

First Time Setup

Setting the Clock with the AccuClock Function

To use the AccuClock function, the CD/HDD receiver must be able to receive RDS radio stations, which means an FM

antenna must be connected. Be sure to connect an FM antenna before attempting to use this function (see page 17).

The very first time you turn on the CD/HDD receiver, the AccuClock function automatically sets the CD/HDD

receiver’s clock based on the CT (Clock Time) information present in an RDS radio broadcast. While the clock is being

set, “Wait…” appears on the display, as shown. Note that it may take up to 5 minutes to set the clock.

When the clock has been set, the message “Clock Adjusted” scrolls across the display, then the day and time are dis-

played for a while, as shown.

00:01.

2008 . 01 . 01

ait . . .

The AccuClock function automatically updates the clock daily at 2 A.M., 3 A.M., and 2 P.M.

If for some reason the clock cannot be set automatically, see “Setting AccuClock to Use a Specific Station” on page 62

and “Setting the Clock Manually” on page 63.

Turning Off the AccuClock Function

If you don’t want AccuClock to automatically update the clock each day, you can turn it off as follows.

Press the [TIMER] button.

TIMER

Clock

Timer 1

Timer 2

Press [ENTER] with “Clock”

selected.

The sub-menu appears and the CD/HDD

receiver enters clock setting mode.

Use the Up and Down [q]/[w] but-

ENTER

tons to select “AccuClock”, and

then press [ENTER].

To turn off AccuClock, press the

Up or Down [q]/[w] button until the

asterisks disappear.

Clock

RDS-CT Station

: FM 87.50MHz

The asterisks indicate that the

AccuClock function is on.

The AccuClock function is off. To turn

AccuClock back on again, press the Up

or Down [q]/[w] button so that the aster-

isks are displayed.

Note:

The AccuClock function cannot be turned off until the clock

has been set.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations

Selecting the Input Source

You can select HDD, CD, AM, FM, or a connected component (LINE 1, TAPE, DOCK, USB or DIGITAL) as the input

source.

On the CD/HDD receiver, press the [INPUT

SELECTOR] button repeatedly.

On the remote controller, press the INPUT

[q]/[w] buttons repeatedly.

Each time you press these buttons, you can select the

previous or next input source.

The input sources are selected in the following order.

HDD

USB

Using other buttons:

DIGITAL*

DOCK*

TAPE*

LINE

* Input Display can be changed (see page 45).

Tip:

HDD 1 button*

You can also use the CD/HDD receiver’s MULTI JOG

dial to switch the input source while any input source is

displayed.

Switches to HDD for playback.

CD 1 button*

Switches to CD for playback.

USB 1 button*

Switches to USB for playback.

TUNER (BAND) button

Selects AM or FM as the input source. If you press this

button repeatedly, you can switch the radio band.

* These buttons also work in the Standby mode.

Adjusting the Volume

Using Headphones

Turn the [VOLUME] control clockwise to

increase the volume or counterclockwise to

decrease it.

Turn down the volume, then connect your stereo head-

phones to the PHONES minijack.

You can adjust the volume and mute the sound, as

explained earlier.

The speakers output no sound while the headphones are

connected.

Remote

CD/HDD receiver

controller

PHONES jack

You can also use remote controller’s VOL [q]/[w] but-

ton.

The default setting is “10”. You can adjust the volume

from MIN, 01 through 41 to MAX.

Notes:

• Do not connect the audio output jack of any other device

to the PHONES jack, because it may cause a malfunction

of the device.

• When you use headphones, Onkyo recommend that you

deactivate Audyssey EQ™. About Audyssey EQ™, see

page 26.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Tone

You can use the following buttons on the remote controller to adjust the tone.

Using the Direct Function

Press the [DIRECT] button.

When the Direct function is on, the tone

controls are bypassed, so you can enjoy a

pure sound, and the DIRECT indicator

lights up.

DIRECT

TONE

S.BASS

MUTING

To turn off the Direct function, press the

[DIRECT] button again.

When the Direct function is off, the tone

controls can be used to adjust the sound.

q/w

ENTER

DIRECT indicator

Adjusting the Bass and Treble

Direct On

Press the [TONE] button to select

“BASS:0”.

Remote

controller

Muting the Sound

Press the [MUTING] button.

The output is muted and the MUTING

indicator flashes on the display.

To unmute the CD/HDD receiver, press

the [MUTING] button again.

Use the Up and Down [q]/[w] but-

tons to adjust the bass.

The default setting is “ 0”. You can

adjust the bass and treble from –3 to +3.

Press [ENTER], and then use the

Up and Down [q]/[w] buttons to

adjust the treble.

MUTING indicator

Muting

Notes:

• If you press no buttons for 8 seconds, the

previous display will appear automati-

cally.

• If you press the [TONE] button while the

Direct function is on, the Direct function

will be turned off.

Tips:

While the CD/HDD receiver is muted:

• Turning the [VOLUME] control on the

CD/HDD receiver or pressing the VOL

[q]/[w] button on the remote controller

will unmute the CD/HDD receiver.

• If you turn the CD/HDD receiver off, the

next time you turn it on, the CD/HDD

receiver will be unmuted.

Using the Super Bass Function

Press the [S.BASS] button.

The S.BASS indicator lights up.

To turn off the Super Bass function, press

the [S.BASS] button again.

S.BASS indicator

S . Bass On

Note:

If you press the [S.BASS] button while the

Direct function is on, the Direct function

will be turned off.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using Audyssey EQ™ and Audyssey Dynamic EQ™

Audyssey EQ™ optimizes the audio quality set for the

recommended Onkyo speakers. The recommended

speakers are D-112E and D-N10BX.

Deactivating Audyssey Dynamic EQ™

Press the [TOOLS] button.

With Audyssey EQ™ enabled,

Audyssey Dynamic EQ™ becomes enabled by default.

You can deactivate Audyssey Dynamic EQ by selecting

“Off” in step 4 below. When Audyssey EQ™ is activated

while the Direct function is on, the Direct function will

be turned off.

Use the Up and Down [q]/[w] but-

tons to select “Audio”, and then

press [ENTER].

Notes:

Tool

Record

Audio

Audyssey Dynamic EQ™ allows you to maintain the

proper octave-to-octave balance at any volume level in

accordance with the preset speakers.

• In order to record with appropriate sound,

Audyssey EQ™ is automatically deactivated during a

recording. After the recording is finished,

Audyssey EQ™ and Audyssey Dynamic EQ™ will

resume as previously set.

Use the Up and Down [q]/[w] but-

tons to select “Dynamic EQ”,

and then press [ENTER].

Press the [TOOLS] button.

Audio

Audyssey EQ

Dynamic EQ

Use the Up and Down [q]/[w] but-

tons to select “Audio”, and then

press [ENTER].

Use the Up and Down [q]/[w] but-

Tool

Record

Audio

tons to select “Off”, and then

press [ENTER].

Audio

Dynamic EQ

: Off

Press [ENTER] with

“Audyssey EQ” selected.

“Complete!” will be displayed, and the

setting is completed.

Audyssey Dynamic EQ™ becomes

deactive and the Dynamic EQ indicator

goes off.

Audio

Audyssey EQ

[Dynamic EQ]

Use the Up and Down [q]/[w] but-

When the Direct function is on while

Audyssey Dynamic EQ™ is activated,

Audyssey Dynamic EQ™ will be deactivated. In this

status, when the Direct function is turned off,

Audyssey Dynamic EQ™ will resume.

tons to select the speaker, and

then press [ENTER].

Audio

Audyssey EQ

:D-112E

About Audyssey Dynamic EQ™

(The above is an example when D-

112E is selected.)

“Complete!” will be displayed, and the

setting is completed.

Audyssey Dynamic EQ™ becomes

active and the Dynamic EQ indicator

lights up.

Audyssey Dynamic EQ solves the problem of

deteriorating sound quality as volume is decreased by

taking into account human perception and room

acoustics. Dynamic EQ selects the correct frequency

response moment-by-moment at any user-selected

volume setting. The result is bass response and tonal

balance that remains constant despite changes in

volume. Dynamic EQ combines information from

incoming source levels with actual output sound

levels in the room, a prerequisite for delivering a

loudnesscorrectionsolution. Audyssey Dynamic EQ

works in tandem with Audyssey EQ to provide well-

balanced sound for every listener at any volume level.

Dynamic EQ indicator

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation of Music Data

This section explains how the CD/HDD receiver deals with the music data saved in the HDD and USB devices. When

copying (recording) or deleting music data, you must first press the [LIBRARY] button on the CD/HDD receiver or

remote controller to read the contents and display the list. Also, when editing the music information, you must start by

selecting the track from the list.

USB Device

HDD

The list is displayed in the hierarchical structure of fold-

ers (artist names and album names) and files (tracks).

You can copy and erase the music data when a folder or

file is selected. At this time, the folders or files displayed

in the list are the target of copying or erasing. When all

file/folder erase is executed by selecting the option “All

Erase”, all folders and files currently displayed in the list

will be erased. When “one file/folder erase” is executed

by selecting the option “1 Erase”, one folder or file

selected will be erased.

The list is displayed in a set of search categories such as

the artist, album, and track.

Unlike the USB device, it is always necessary to read the

track list for copying, erasing or editing. (The operation

cannot be performed by selecting only artist or album.)

When you want to erase all files in the HDD, first select

“ALL” from Artist Category or Album Category to go to

the track list, and then erase all files by selecting the

option “All Erase”.

However, for the files created by Tuner Recording or

Line Recording, separately enter the Tuner recording

category or the Line recording category, and then erase

all files by selecting the option “All Erase” on the track

list.

Example: Deleting an album

Select an album and execute “one file/folder” erase

(1 Erase).

Example: Deleting an album

Select an album, select an arbitrary track, and then exe-

cute “all file erase” (All Erase).

Folder (Album)

File (Track)

Artist

Album

One file/folder

erase

All file erase

Erased

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing CDs

Basic Operations of Playback

The CD/HDD receiver can playback Audio CDs and CD-R/RW (data CDs) in which MP3/WMA/AAC/WAV files are

recorded. For the supported formats, see page 70.

Disc tray

Switch the input

source to CD (see

page 24).

OPEN/CLOSE

Load the CD.

Start playback.

1 Press the Open/Close [0] button

Press the Play/Pause [1/3] or Play

CD/HDD receiver

to open the disc tray.

[1]button.

2 Place the CD on the tray with the

label-side facing up.

Album name

Track 01

00:08

Place 8 cm CDs in the center of the

tray.

Remote controller

Tip:

When you press the remote

controller’s CD [1] button,

the CD/HDD receiver auto-

matically selects an appropri-

ate input source and starts playback of a

track.

3 Press the Open/Close [0 ] button

to close the disc tray.

For audio CDs, the CD/HDD

receiver starts a search for CD

information after the disc tray

closed. See “Retrieving Audio CD

Information” on page 30.

Accessing

Gracenote

The information (title, album name,

and so on) of the audio CD is displayed.

When there is MP3/WMA/AAC/WAV

file tag information, it is displayed in

the same way. If no tag information is

contained, Unknown Album or

To pause playback:

Press the remote controller's Pause [3] button or the

CD/HDD receiver’s Play/Pause [1/3] button. To resume

playback, press the Play/Pause [1/3] button again.

To stop playback:

Press the Stop [2] button on the CD/HDD receiver or

remote controller.

Unknown Artist is displayed.

To select tracks:

Artist name

Track name

Press the [LIBRARY] button to return to the track list, then

press the Up and Down [q]/[w] buttons to select a track.

To select the previous or next track:

Artist name

Track 01

00:00

1/14

Press the Previous/Next [7]/[6] buttons or turn the

MULTI JOG dial on the CD/HDD receiver to select the pre-

vious or next track.

Format

To fast forward or fast reverse:

Press the Fast Reverse/Fast Forward [5]/[4] buttons

during playback or pause. Where you want to start play-

back, release the button.

To remove the CD:

Press the Open/Close [0] button and remove the CD.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing CDs—Continued

During stop

Playing Selected Tracks

Artist name Track number/Total tracks

Switch the input source to CD.

Artist name

Press the INPUT [q]/[w] buttons. You

can also use the [INPUT SELECTOR]

button to select the input source.

Track01

00:00

1/14

Format

Track name

Album name

Track01

00:00

Select the track you want to play.

Audio CDs

1 Press the [LIBRARY] button.

2 Use the Up and Down [q]/[w]

Album name

Track01

buttons to select the track.

38:56

Total

Total tracks

Total time

Data CDs

Album name

Track01

MP3

128 kbps

Bit rate

Press [ENTER] to start playback.

Format

During playback and pause

■ Selecting Tracks by Number

Album name

Track01

00:08

Track?

15 / 16

Elapsed time of current track

Progress bar

Artist name

Track01

00:48

1/14

Press:

To select:

Track number/

Total tracks

Elapsed time of current track

Track #5

Track #10

Track #15

Audio CDs

Artist name

Used to enter numbers over 10.

Track01

- 00:03

1/14

Remaining track time

Data CDs

Switching the Display

You can switch the display by pressing the remote con-

troller's [DISPLAY] button repeatedly.

Artist name

Track01

MP3

128 kbps

During the list display

2-line display

Format

Bit rate

Track01

Track02

3-line display

Track01

Track02

Track03

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing CDs—Continued

■ Retrieving CD information manually

If track information is wrong, you can retry the search

manually.

Retrieving Audio CD Information

The CD/HDD receiver initially embeds the information

on approximately 350,000 albums among the CD data-

base provided by Gracenote music recognition ser-

Switch the input source to CD.

Press the INPUT

vice*.

When an audio CD is set, the CD information is auto-

matically searched in the registered information. If infor-

mation is not registered in the CD/HDD receiver for such

reasons as the CD is new, it can be searched through the

Internet. (Internet connection is required.)

[q]/[w] buttons. You can

also use the [INPUT

SELECTOR] button to

select the input source.

Gracenote Music Recognition Service is music CD database

service constructed on servers located on the Internet. The

CD/HDD receiver can connect the database and download

useful information such as album titles, artist names, song titles,

and more.

Press the [TOOLS] button and

then press [ENTER] with “Tool”

selected.

Tool

Record

Audio

■ Retrieving CD information automatically

Switch the input source to CD.

Press the INPUT

[q]/[w] buttons. You can

also use the [INPUT

SELECTOR] button to

select the input source.

Use the Up and Down [q]/[w] but-

tons to select “Gracenote

Access”, and then press

[ENTER].

Press the [TOOLS] button and

then press [ENTER] with “Tool”

selected.

Tool

Gracenote Service

Gracenote Access

Tool

Record

Audio

Use the Up and Down [q]/[w] but-

tons to select “OK”, and then

press [ENTER].

Use the Up and Down [q]/[w] but-

tons to select “Gracenote Ser-

vice”, and then press [ENTER].

Tool

Gracenote Access

Ready?

:OK

Tool

The CD/HDD receiver starts a search

for CD information. If multiple candi-

dates are searched, select the proper

information and press the [ENTER]. To

cancel the search, use the Up and Down

[q]/[w] buttons to select “Cancel”, and

then press [ENTER].

Gracenote Service

Gracenote Access

Use the Up and Down [q]/[w] but-

tons to select “On”, and then

press [ENTER].

Accessing

Gracenote

Tool

Gracenote Service

:On

Music recognition technology and related data are provided

by Gracenote . Gracenote is the industry standard in music

Complete!

recognition technology and related content delivery.

For more information visit www.gracenote.com.

The CD/HDD receiver starts a search

for CD information after the CD is

loaded. If multiple candidates are

searched, select the proper information

and press the [ENTER].

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing CDs—Continued

Random Playback

Repeat Playback

With random playback, all of the tracks on the disc are

played in random order.

With repeat playback, you can play an entire CD repeat-

edly, play one track repeatedly. You can combine repeat

playback with random playback to play all of the tracks

repeatedly.

RANDOM

REPEAT

Press the [RANDOM] button

repeatedly until the RANDOM indi-

cator appears.

Press the [REPEAT] button repeat-

edly until the REPEAT or

RANDOM indicator

REPEAT 1 indicator appears.

REPEAT or REPEAT 1 indicator

Artist name

Album name

00:00

1/14

Artist name

Album name

00:00

1/14

To start random playback, press

the Play [1] button.

To start repeat playback, press the

Play [1] button.

The following display appears for three

seconds.

The following display appears for three

seconds.

Artist name

Track03

00:00

3/14

Artist name

Track03

00:00

3/14

Track currently playing

Cancelling Random Playback

• To cancel random playback, press the [RANDOM]

button repeatedly until the RANDOM indicator disap-

pears.

• Random playback is cancelled when turn off the

CD/HDD receiver.

Cancelling Repeat Playback

• To cancel repeat playback, press the [REPEAT] button

repeatedly until both the REPEAT and REPEAT 1

indicators disappear.

• Repeat playback is cancelled when you turn off the

CD/HDD receiver.

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the Radio

Tuning into AM/FM Radio Stations

The CD/HDD receiver won’t pick up any radio signals without an antenna connected, so you must connect the antenna

to use the tuner (see page 17).

Switch the input source to

FM or AM (see page 24).

ENTER

( TUNING

)

When tuned into a station, the Tuned

indicator appears.

When tuned into a stereo FM station, the FM STEREO indicator

appears as well.

TUNER

FM 87.50 MHz – – ch

FM STEREO

AUTO

Band

Frequency

Press the [ENTER] repeatedly to select the tuning mode.

AUTO indicator

•

Auto Tuning Mode

The AUTO indicator appears and stereo radio recep-

tion is possible.

•

Manual Tuning Mode

The AUTO indicator is not displayed and radio reception will be in mono.

Use the Fast Reverse and Fast Forward [5]/[4] buttons to tune into

a station.

In Auto tuning mode, once a station is found, tuning stops automatically.

Radio Frequency can be changed in 0.05 MHz steps for FM and 9 kHz or 10 kHz steps

for AM.

In Manual Tuning mode, the frequency stops changing when you release the button.

Press the button repeatedly to change the frequency one step at a time.

Adjusting the Antennas

Adjusting and installing the FM antenna

Choose a location for the FM antenna while listening to an FM station.

Adjusting the AM antenna

Adjust the location and position of the AM

antenna while listening to an AM station to

achieve the best reception.

Change the direction of the

Affix the antenna with a thumbtack. (Do not

antenna to achieve the best

reception.

push the thumbtack through the antenna.)

Caution:

Be careful not to prick your finger!

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the Radio—Continued

Displaying Radio Information

DISPLAY

Press the remote controller’s [DISPLAY] button repeatedly to display more radio information.

Frequency

FM 87.50 MHz 6ch

*1 If the selected preset has no name, “No Name” appears

briefly and then the frequency is displayed. See “Nam-

ing Presets” on page 39.

ONKYO-FM 6ch

Preset name^*1

Receiving RDS

RDS is only available in areas where RDS broadcasts

are available.

What is RDS?

RDS stands for Radio Data System and is a method of

transmitting data in FM radio signals. It was developed

within the European Broadcasting Union (EBU) and

Press the [DISPLAY] button repeatedly to display

the following RDS information.

many European FM radio stations use it these days.

The CD/HDD receiver supports and displays the Pro-

gram Service Name (PS) and Radio Text (RT) types of

RDS data.

Frequency and preset number

The RDS indicator appears on the display when the

CD/HDD receiver is tuned to an FM station that supports

RDS.

Preset name^*2

Notes:

• If the signal from an RDS station is weak, RDS data

may be displayed intermittently or not at all.

• The message “Waiting…” may appear while the RT

data is being received.

Program Service Name

Radio Text (if available)

*2 If the selected preset has no name, it will be skipped and the next

Program Service Name will be displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the Radio—Continued

Presetting FM Stations Automatically (Auto Preset)

With the Auto Preset function, you can automatically

preset all of the FM radio stations available in your area

in one go. Presets make it easy to select your favorite

stations and eliminate the need to tune the radio manu-

ally each time you want to change stations.

Use the Up and Down [q]/[w] but-

tons to select “OK”, and then

press [ENTER].

Tool

Auto Preset?

:OK

Auto Preset Caution!

To cancel the Auto Preset function at this

point, select “Cancel” and then press

[ENTER].

Any existing presets will be deleted when the

Auto Preset function is run.

Use the Up and Down [q]/[w] but-

tons to select “Yes”, and then

press [ENTER].

BAND

TOOLS

Tool

Auto Preset?

Preset OK? :Yes

ENTER

Up to 20 stations can be preset and pre-

sets are stored in frequency order.

To cancel the Auto Preset function at this

point, select “No” and then press

[ENTER].

Press the [BAND] or INPUT [q]/[w]

button to select “FM” .

Note:

Depending on your location, a preset may be stored with

no station and you will hear only noise when you select

it. In this case, delete the preset (see page 38).

FM 87.50 MHz – – ch

Make sure the FM antenna is positioned

to achieve the best possible reception.

After Storing Presets Y o u Can:

• Select them (see page 36)

• Name them for easy identification (see page 39)

• Copy them (see page 37)

• Erase them (see page 38)

Press the [TOOLS] button and

then press [ENTER] with “Tool”

selected.

Tool

Record

Audio

Use the Up and Down [q]/[w] but-

tons to select “Auto Preset”, and

then press [ENTER].

Tool

Preset Copy

Auto Preset

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the Radio—Continued

Presetting AM/FM Stations Manually

With the Preset Write function, you can manually preset

individual AM and FM stations. Presets make it easy to

select your favorite stations and eliminate the need to

tune the radio manually each time you want to change

stations. FM stations can also be preset automatically

(see page 34).

To store the station, press

[ENTER].

If no station has yet been stored to the

selected preset, “Complete!” appears and

the station is stored.

About Presets

Complete!

• You can store up to 40 stations as presets and this

can be any combination of AM and FM stations.

For example, 27 FM and 13 AM, or 18 FM and

22AM.

If a station has already been stored in the

selected preset, the message

“Over Write?” appears.

• Although AM and FM presets share the same

numbers, they’re selected independently. For

example, preset #1 will store an AM station when

the AM band is selected, and an FM station when

the FM band is selected.

• Stations can be stored to presets in any order. For

example, you could store preset #5 first, #1 sec-

ond, and so on.

Tool

Preset Write?

Over Write? :Yes

To overwrite the previously stored sta-

tion, press the Up and Down [q]/[w] to

select “Yes”, and then press [ENTER].

To not overwrite the previously stored

station, press the Up and Down [q]/[w]

to select “No”, and then press [ENTER].

If the message “Memory Full” appears,

all 40 presets have been stored and you’ll

need to erase some presets before you

can store any more stations (page 38).

BAND

TOOLS

ENTER

Memory Full

Tune into the station that you want

to store as a preset.

Repeat steps 1 to 5 to preset more radio

stations.

Press the [TOOLS] button and

then press [ENTER] with “Tool”

selected.

Note:

If the current FM station supports RDS and PS (Program

Service Name), the station’s name will be displayed

instead of the frequency. (See page 33 for more on

RDS.)

Tool

Record

Audio

After Storing Presets Y o u Can:

Use the Up and Down [q]/[w] but-

tons to select “Preset Write?”, and

then press [ENTER].

• Select them (see page 36)

• Name them for easy identification (see page 39)

• Copy them (see page 37)

Tool

• Erase them (see page 38)

Preset Write?

The preset number flashes.

To cancel the Preset Write function at

this point, press the [RETURN] button.

Use the Up and Down [q]/[w] but-

tons to select a preset.

Tool

Preset Write?

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the Radio—Continued

Selecting Preset Stations

Tuning into weak stereo FM stations

BAND

FM 87.50 MHz 1 ch

AUTO indicator

(PRESET

FM 87.50 MHz 1 ch

)

You must store some presets before you can select them

(see pages 34 and 35).

If the signal from a stereo FM station is weak, it may be

impossible to get good reception. In this case, switch to

Manual Tuning mode and listen to the station in mono.

Use the [BAND] or INPUT [q]/[w]

Noise and sound interruption can be reduced.

When returning to Auto Tuning Mode, press the ENTER

again. Normally, leave the AUTO indicator displayed.

The CD/HDD receiver automatically receives FM radio

in stereo.

button to select “AM” or “FM”.

The preset you selected the last time you

listened to the radio will still be selected.

Use the Previous and Next

[7]/[6] buttons to select a

preset.

Press the Previous [7] button to select

the previous preset. Press the Next

[6] button to select the next preset.

Tip:

• You can also use the number buttons as

shown in the examples below to select

presets.

To select:

Press:

Preset #8

Preset #10

Preset #22

Used to enter numbers over 10.

You can also use the front panel controls.

1 Use the [INPUT] button to select “AM” or “FM”.

2 Turn the MULTI JOG dial to select a preset.

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the Radio—Continued

Editing Presets

Using the two basic functions of copying and deleting,

you can copy a radio station preset to a channel to

another channel, change a channel number, and delete an

unnecessary channel.

Use the Up and Down [q]/[w] but-

tons to select the destination pre-

set, and then press [ENTER].

If no station has yet been stored in the

destination preset, the station is copied

and “Complete!” appears.

Copying Presets

With the Preset Copy function, you can organize your

presets in the order you want. When you copy a preset,

its name is also copied.

If a station has already been stored in the

destination preset, the message

“Over Write?” appears.

• To overwrite the previously stored sta-

tion, use the Up and Down [q]/[w] to

select “Yes”, and then press [ENTER].

• To not overwrite the previously stored

station, use the Up and Down [q]/[w]

to select “No”, and then press

BAND

TOOLS

ENTER

[ENTER].

If the message “Memory Full” appears,

all 40 presets have been stored and you’ll

need to erase some presets before you can

store any more stations (see page 38).

(PRESET

)

Select the preset you want to copy

(see page 36).

Press the [TOOLS] button and

then press [ENTER] with “Tool”

selected.

Tip:

If your favorite station is stored in preset #4 and you

want to make it preset #6, first copy preset #4 to preset

#6. To keep the station that's already stored in preset #6,

you may want to copy it to an unused preset first. And

then erase preset #4.

Tool

Record

Audio

Use the Up and Down [q]/[w] but-

tons to select “PresetCopy?”, and

then press [ENTER].

Tool

Preset Copy?

The number of the preset to be copied

flashes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the Radio—Continued

Erasing Presets

BAND

TOOLS

ENTER

(PRESET

)

Select the preset you want to

erase (see page 36).

Press the [TOOLS] button and

then press [ENTER] with “Tool”

selected.

Tool

Record

Audio

Use the Up and Down [q]/[w] but-

tons to select “PresetErase”, and

then press [ENTER].

Tool

Preset Write

Preset Erase

The number of the preset to be copied

flashes.

Press [ENTER].

Tool

Preset Erase?

The confirmation message “Erase

OK?” appears.

Use the Up and Down [q]/[w] buttons to

select “Yes”, and then press [ENTER].

Tool

Preset Erase?

Erase OK? :Yes

“Complete!” will be displayed, and the

preset's name has been deleted.

To cancel the erase operation, use the Up

and Down [q]/[w] buttons to select

“No”, and then press [ENTER].

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the Radio—Continued

Naming Presets

Selecting letters:

Press the number buttons repeatedly to

select the available letters. For example,

press the [2] button repeatedly to select:

A, B, or C.

You can name presets for easy identification using alpha-

betic, numeric, marks and symbols. The preset name

may contain up to eight characters.

Press the [0] button repeatedly to select:

0 or (space)

After you select a desired character,

move to the next input position by press-

ing the Left and Right [e]/[r] buttons.

Number

CAPS

buttons

Selecting numbers and symbols:

Use the number buttons to select num-

bers.

Press the [>10] button repeatedly to

select: (space) . / * - , ! ? & ' ( )

After you select a desired character,

move to the next input position by press-

ing the Left and Right [e]/[r] buttons.

BAND

TOOLS

ENTER

Notes:

• Not all of the symbols can be entered by

using the number buttons. Use the Up

and Down [q]/[w] buttons to select from

the full range of symbols.

• Up to 8 characters can be input. If you

attempt to input ninth character, “Name

Full” is displayed. Proceed to the next

step.

Select the preset you want to

name (see page 36).

Press the [TOOLS] button and

then press [ENTER] with “Tool”

selected.

Deleting/editing characters:

Inserting a new character:

Tool

Record

Audio

Deleting preset's name:

See page 40.

To cancel the Name In function, press the

[RETURN] button.

Use the Up and Down [q]/[w] but-

tons to select “Name In”.

The CD/HDD receiver enters the charac-

ter input mode.

Press [ENTER] to finish entering.

“Complete!” will be displayed, and the

preset has been named.

Tool

Name In

Name Erase

Available Characters

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

a b c d e f g h i j k l m n o p q r s t u v w x y z

0 1 2 3 4 5 6 7 8 9

Tool

Name In?

A ]

;

(

)

’

”

(space)

(insert)

Character group Input position

À Á Â Ã Ä Å Æ Ç È É Ê Ë Ì Í Î Ï Ð Ñ Ò Ó Ô Õ Ö × Ø Ù Ú

Û Ü Ý Þ ß à á â ã ä å æ ç è é ê ë ì í î ï ð ñ ò ó ô õ ö ÷ ø ù

ú û ü ý þ ÿ ¡ ¢ £ ¤ ¥ ¦ § ¨ © ª « ¬ - ® ¯ ° ² ³ ´ µ ¶ · ‚ ¹ ° »

¼ ½ ¾ ¿

Press the [CAPS] button repeat-

edly to select one of the following

character groups:

Uppercase letters

Lowercase letters

Numbers and symbols

Umlaut letters and symbols

£]

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the Radio —Continued

Editing Characters

Erasing a Preset’s Name

If the character input mode is not currently selected, per-

form steps 1 to 3 of “Naming Presets” on page 39.

1 Switch the input source to FM or AM (see

page 24).

1 Use the Left and Right [e]/[r] buttons to select a

character to be changed or deleted.

The character flashes.

2 Press the Previous/Next [7]/[6] buttons to

select the preset whose name you want to erase.

3 Press the [TOOLS] button and then press

[ENTER] with “Tool” selected.

2 To change the character:

Follow the steps 4 and 5 of “Naming Presets” on

page 39 to select a desired character.

To delete the character:

4 Use the Up and Down [q]/[w] buttons to select

“Name Erase”, and then press [ENTER].

5 Use the Up and Down [q]/[w] buttons to select

Press the [CLEAR] button.

“OK”, and then press [ENTER].

3 Press [ENTER] to finish the change/deletion.

Pressing the [RETURN] button cancels the

“Complete!” will be displayed, and the preset name

has been erased.

To cancel the Name Erase function, press the Up and

Down [q]/[w] buttons to select “Cancel”, and then

press [ENTER].

change/deletion and displays the previous display.

Inserting a New Character

If the character input mode is not currently selected, per-

form steps 1 to 4 of “Naming Presets” on page 39.

1 Use the Left and Right [e]/[r] buttons to select

the character immediately after the insertion

point.

That character flashes.

Tool

Name In?

A ]

DEAM

2 Press the Up [q] button to display

Tool

Name In?

A ]

DR AM

3 Enter a character to be inserted following step 5 of

“Naming Presets” on page 39.

Tool

Name In?

A ]

DREAM

4 Press [ENTER] to finish the insertion.

Pressing the [RETURN] button cancels the insertion

and displays the previous display.

Download from Www.Somanuals.com. All Manuals Search And Download.

USB Device Playback

The iPod , USB storage device, and digital audio player can be connected to the CD/HDD receiver via USB, and the

tracks on them can be played. You can use the CD/HDD receiver’s remote controller to carry out the basic operations.

For the supported formats, see “Supported Formats” on page 72.

USB Mass Storage Device Requirements

Compatible USB Devices

• USB devices formatted with the FAT16 or FAT32 file

system are supported.

■ iPod models

The CD/HDD receiver supports the following iPod

• If the storage device has been partitioned, only music

models:

files in the first partition can be played.

iPod touch

• Each folder may contain up to 60,000 music files, and

iPod classic

iPod with video*

folders may be nested up to eight levels deep.

• USB hubs and USB devices with hub functions are not

iPod nano (3rd generation)

supported.

iPod nano (2nd generation)

iPod nano (1st generation)

Only when the iPod with video is set to the music mode. Play-

back cannot be made in the video mode.

USB Device Folders and Files

■ USB storage devices and digital audio

players

In the following structure of the folders (albums) and the

files (tracks), if you do not select a track for playback,

the files will be played in numerical order starting with

file 1.

When you press the [LIBRARY] button, the folders and

files are listed in the order of 1➔B➔E➔G.

For the iPod models, the display is based on the track

information stored in the iPod.

The CD/HDD receiver supports the USB storage devices

such as USB flash memory and USB hard disk drive, and

also supports various kinds of digital audio players.

However, they are limited to the devices that support the

USB Mass Storage Class*.

The USB Mass Storage Class is a standard established for con-

necting the large capacity memory devices (mass storage

devices) to the USB port of a computer. Because the USB

devices conforming to this standard are recognized as external

memory devices without the need for special drivers or soft-

ware, even a digital audio player can be handled in the same way

as an external memory device.

USB device 1st level 2nd level 3rd level 4th level

Folder

Notes:

• While being connected to the CD/HDD receiver, the iPod

or USB devices cannot be operated directly.

• For the functions of the iPod and USB devices, see their

instruction manuals.

• When connecting the iPod, use a USB cable compatible

with the iPod.

• Available functions or operation may vary depending on

the software version of the iPod. Update the iPod soft-

ware to the latest version before using.

File

• Onkyo accepts no responsibility whatsoever for the loss

or damage to data stored on the iPod or USB device when

that device is used with the CD/HDD receiver. Onkyo

recommend that you back up your important music files

beforehand.

• To remove the USB devices, stop the playback and hold

down the [STOP] button until “NO USB” appears.

• Playback may not be possible with some USB mass

storage devices.

Download from Www.Somanuals.com. All Manuals Search And Download.

USB Device Playback—Continued

Basic Operations of Playback

INPUT

SELECTOR

USB port

USB cable

Plug your USB device into the CD/HDD receiver’s USB port.

In the case of an iPod or digital audio player:

1. Connect the USB cable to the connector of the iPod or digital audio player.

2. Plug the USB cable into the CD/HDD receiver’s USB port.

The iPod or digital audio player automatically turns on. The CD/HDD receiver may take

approximately one minute to recognize the iPod, so wait until the recognition is com-

pleted.

Switch the input source to USB.

Artist name

Press the INPUT [q]/[w] buttons. You can

CD/HDD

receiver

Remote

controller

also use the [INPUT SELECTOR] button

Album name

to select the input source.

Track01

00:00

Track name Format

The track information appears on the dis-

play of the CD/HDD receiver. (ONKYO

logo appears on the display of the iPod.)

Start playback.

Album name

Press the Play/Pause [1/3] or Play

CD/HDD

receiver

Remote

controller

Track01

[1] button.

00:11

Tip:

Elapsed time of current track

When you press the remote controller's

USB [1] button, the CD/HDD receiver

automatically selects an appropriate input

source and starts playback of a track.

Playback starts with the first track of the

first folder.

Removing the USB Device

1 Stop the playback and switch the input source to USB.

2 Hold down the Stop [2] button until “No USB” appears.

3 Disconnect the USB or USB cable from the CD/HDD receiver.

Do not disconnect the USB cable until you see the “No USB” message.

Download from Www.Somanuals.com. All Manuals Search And Download.

USB Device Playback—Continued

Switching the Display

Playing Selected Tracks

You can switch the display by pressing the remote con-

troller’s [DISPLAY] button repeatedly.

Switch the input source to USB.

Press the INPUT [q]/[w] buttons. You

can also use the [INPUT SELECTOR]

button to select the input source.

During the list display

2-line display

Track01

Track02

3-line display

Track01

Track02

Track03

Select the track you want to play.

In the case of iPod, select the track based

on the information managed in the iPod.

During stop

1 Press the [LIBRARY] button.

Artist name Track number/Total tracks

2 Use the Up and Down [q]/[w]

buttons to select a desired folder,

and then press [ENTER].

Artist name

Track01

00:00

1/14

Format

Track name

Album name

Songs

Album name

Track01

3 Use the Up and Down [q]/[w]

00:00

1/14

buttons to select a desired track.

Track01

Track02

Album name

Track01

MP3

128 kbps

Press [ENTER] to start playback.

Bit rate

Format

During playback and pause

Album name

Track01

00:08

Elapsed time of current track

Progress bar

Artist name

Track01

00:48

1/14

Track number/

Total tracks

Elapsed time of current track

Artist name

Track01

MP3

128 kbps

Format

Bit rate

Download from Www.Somanuals.com. All Manuals Search And Download.

USB Device Playback—Continued

Repeat/Random Playback

REPEAT

RANDOM

With random playback, the tracks recorded on the USB

device are played in random order. With repeat playback,

you can play a group of tracks repeatedly or play one

track repeatedly.

See page 31 for details on repeat and random playback.

Press the [REPEAT] or [RANDOM] button repeat-

edly to set random or repeat playback.

Tips:

The range of tracks to be played in random and repeat

playback varies depending on the devices connected.

For the USB devices except for the iPod, all tracks are

played randomly or repeatedly.

For the iPod, tracks in the same folder as the selected

track are played randomly or repeatedly.

Note:

If the USB device contains folders deeper than eight levels,

the repeat/random playback is not performed for the tracks

saved in the folders deeper than eight levels.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing External Components

Switch the input source to a com-

ponent you want to have interac-

tive control.

Press the INPUT [q]/[w] buttons. You

can also use the CD/HDD receiver’s

[INPUT SELECTOR] button to select

the input source.

Connect the external components correctly. See “Con-

necting Other Components” on page 19.

Press the [TOOLS] button and

then press [ENTER] with “Tool”

selected.

INPUT

Tool

Record

Audio

Switch the input source.

Press [ENTER] with “Name

Select” selected.

Press the INPUT [q]/[w] button to select

LINE1, LINE2, or LINE3.

Tool

Name Select

You can also use the CD/HDD receiver’s

[INPUT SELECTOR] button to select

the input source.

Press the Up and Down [q]/[w] to

select a u-capable components.

TAPE

VIDEO

DAT

Start playback.

For the playback operation, see the

instruction manual of the external com-

ponents connected.

DOCK

CD-R

DIGITAL

CD-R/dig

Making an u Connection with

Onkyo Components

GAME/dig

PC/dig

By making an u (remote interactive) connection

with an Onkyo u-capable component and speci-

fying the selector name of the component, the com-

ponent can be controlled with the u control

interface, working with the CD/HDD receiver.

*1 This should be selected if you connect an

audio processor such as the Onkyo UE-205.

To cancel changing the selector name,

press the [RETURN] button.

Press [ENTER].

“Complete!” will be displayed, and the

selector name of the external component

has been set. The external component

can be controlled via u.

What can you do with u?

You can use the CD/HDD receiver's remote controller

to operate components with an u connection. See

“Controlling External Components” on page 73.

When you start playback on a component with an u

connection, the CD/HDD receiver automatically

switches the input source (Direct Change).

Tool

Name Select

:TAPE

While the CD/HDD receiver is in Standby mode, if

you turn on the power or start the playback of the com-

ponents with an u connection, the CD/HDD

receiver will automatically turn on. When the

CD/HDD receiver is set to Standby mode, the compo-

nents with an u connection will also enter Standby

mode (Auto Power ON/Standby).

Selector indicator Selector name

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording (Transferring Data)

You can record tracks into the CD/HDD receiver’s HDD (hard disk drive). Also, you can transfer the music data stored

in the CD/HDD receiver to your digital audio player and USB storage device, and make an FTP connection with your

computer*. See “Transferring Data” on page 51.

Only for personal computers with Microsoft Windows XP Service Pack 2, Service Pack 3, or Microsoft Windows Vista installed.

Connected

Components

CDs

Radio

Recording CDs (page 48)

Recording from an external component (page 50) Recording the radio (page 50)

Digital audio

USB mass

player

storage device

HDD

(Hard Disk Drive)

USB Mass Storage Device Requirements

Compatible USB Devices

• USB devices formatted with the FAT16 or FAT32 file

system are supported.

■ USB storage devices and digital audio

players

The CD/HDD receiver supports the USB storage devices

such as USB flash memory and USB hard disk drive, and

also supports various kinds of digital audio players.

However, they are limited to the devices that support the

USB Mass Storage Class*.

• If the storage device has been partitioned, only music

files in the first partition can be played.

• Each folder may contain up to 60,000 music files, and

folders may be nested up to eight levels deep.

• USB hubs and USB devices with hub functions are not

supported.

The USB Mass Storage Class is a standard established for con-

necting the large capacity memory devices (mass storage

devices) to the USB port of a computer. Because the USB

devices conforming to this standard are recognized as external

memory devices without the need for special drivers or soft-

ware, even a digital audio player can be handled in the same way

as an external memory device.

Preparation for Recording and

Transferring

Perform the setting of the recording beforehand by refer-

ring to “Setting for recording” on the next page.

When you transfer the data to the digital audio player or

the USB storage device, connect it to the USB port of the

CD/HDD receiver.

Notes:

• For the functions of USB devices, see their instruction

manuals.

• Recording and transferring cannot be performed between

the CD/HDD receiver and the iPod. Only the playback

can be performed.

For the details on how to use the USB device, see the

instruction manual attached to the device.

• When the AC power adapter is attached to the digital

audio player or the USB storage device, Onkyo recom-

mend that you connect the AC power adapter to the

domestic power supply. When using the batteries, check

that the remaining battery level is sufficient. Please note

that Onkyo is not responsible for the malfunctions,

recording failures, or music data damages resulting from

insufficient battery power.

• Onkyo accepts no responsibility whatsoever for the loss

or damage to data stored on a USB mass storage device

when that device is used with the CD/HDD receiver.

Onkyo recommend that you back up your important

music files beforehand.

• Recording may be slow depending on the USB device.

• If many tracks are stored in the USB flash memory

(approx. 60,000 files or more), it may take some time for

the recording operation.

• When you record to an SD memory card using a memory

card reader/writer, you may not be able to record depend-

ing on the memory card because the access time is too

slow.

Notes:

• Do not connect the CD/HDD receiver’s USB port to a USB

port on your computer. Music on your computer cannot be

played through the CD/HDD receiver in this way.

• In the process of transferring the data to the digital audio

player or the USB storage device, do not disconnect the

USB cable. Malfunction of the connection device or the

CD/HDD receiver may occur.

• The recording speed varies depending on the recording

format and bit rate.

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording (Transferring Data)—Continued

Setting for Recording

Use the Up and Down [q]/[w] but-

tons to select the record mode,

and then press [ENTER].

When the destination of recording is

USB device, select “USB Record

Mode”. When the destination of record-

ing is HDD, select “HDD Record

Mode”.

Before starting the recording, set the format and bit rate.

Format is a data form of tracks to be recorded. Bit rate

means the quantity of information for recording.

When the quantity of information increases, the sound

quality becomes better, however the data volume

becomes larger.

The data volume and available USB devices that can

transfer the data depends on the format. Select a proper

and optimum format.

Record

USB Record Mode

HDD Record Mode

Sampling

frequency

(The above is an example when USB

Record Mode is selected.)

Format

MP3

(MPEG-2

Audio

Layer-3)

WMA^*2

(Windows

Media Audio

V8.0)

Extension

Bit rate

128 kbps

160 kbps

192 kbps

256 kbps^*1

Press the Up and Down [q]/[w]

buttons to perform the settings for

recording.

*.mp3

44.1 kHz

128 kbps

160 kbps

192 kbps

Record

USB Record Mode

:WMA 128 kbps

*.wma

*.wav

44.1 kHz

—

WAV

—

Format and bit rate

*1 This is the default setting. However, 128 kbps is set in the case

of the data transfer to the USB devices.

*2 Copyright protected WMA files cannot be recorded or trans-

ferred.

(The above is an example when WMA

file and 128 kbps are selected.)

Press [ENTER].

“Complete!” will be displayed, and the

settings for recording have been done.

Note:

AAC files cannot be recorded to the CD/HDD receiver but

only can be transferred via USB port (between HDD and

USB devices).

Press the [TOOLS] button.

Use the Up and Down [q]/[w] but-

tons to select “Record”, and then

press [ENTER].

Tool

Record

Audio

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording (Transferring Data)—Continued

Recording CDs

The CD/HDD receiver can record audio CDs into its HDD at a speed of 4X Max. In addition, recording into the USB

devices is available. See “Setting for Recording” on page 47 for setting before the operation.

Recording All Tracks (CD Recording with One-touch Button)

CD HDD

CD USB

Disc tray

You can easily record an entire CD with the [CD r HDD] button or the [CD r USB] button.

Load the CD you want to record.

1. Press the Open/Close [0] button to open the disc tray.

2. Place the CD on the tray with the label-side facing up.

Place 8 cm CDs in the center of the tray.

3. Press the Open/Close [0] button to close the disc tray.

Start recording.

CD/HDD

receiver

Press the CD/HDD receiver’s CD r HDD or CD r USB button.

When recording onto the HDD, press the CD r HDD button. When recording into a

USB device, press the CD r USB button.

3 / 11

Track 01

14%

Recording of all tracks on the audio CD starts. (The above is an example when the

CD r USB button is pressed.)

When recording ends, the CD/HDD receiver automatically returns to its normal dis-

play.

■ Cancelling recording

Press the Stop [2] button on the CD/HDD receiver or remote controller.

Cancelling the recording halfway may take some time.

CD/HDD

receiver

Remote

controller

■ Restriction on recording CDs

After a CD is recorded, the same CD cannot be continuously recorded for

a certain period of time to protect the copyright regardless of the recording time. The same CD can be recorded again

approx. 74 minutes after its last time recording. If you attempt to record the CD again within approx. 74 minutes, the

waiting time to the next available recording is displayed. (Example: “Wait COPY! 42 min”)

When you use other CDs for recording, continuous recording is possible. It is also prohibited to record 16 or more CDs

within approx. 74 minutes.

Start

Recording of CD1

End

CD1 can’t be recorded.

Approx.74min.

CD1

End

Start

Recording of CD2

CD2 can’t be recorded.

Approx.74min.

CD2

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording (Transferring Data)—Continued

Recording Tracks One-by-one

Recording Using the Remote Controller

You can select one track you want to record.

You can use the remote controller for recording as below.

LIBRARY

ENTER

MULTI JOG

REC

LIBRARY

Load the CD.

When the CD has been loaded, switch

the input source to CD.

Load the CD.

When the CD has been loaded, switch

the input source to CD.

Press the [LIBRARY] button.

After the message “CD reading” appears,

the list of tracks is displayed.

Press the [LIBRARY] button.

After the message “CD reading” appears,

the list of tracks is displayed.

Turn the MULTI JOG dial to select

a track you want to record.

Use the Up and Down [q]/[w] but-

tons to select a track you want to

record.

Press the y REC button.

To cancel the recording, press the Stop

[2] button or [RETURN] button.

Press the [y3] button according

to the destination of recording.

When recording onto the HDD, press the

HDD REC [y3] button. When record-

ing into a USB device, press the USB

REC [y3] button.

Turn the MULTI JOG dial to select

the destination of recording.

REC 1

HDD

REC 1

USB

Use the Up and Down [q]/[w] but-

tons to select either of the follow-

ing, and then press [ENTER].

When recording onto the HDD, select

“REC 1 HDD”. When recording into a

USB device, select “REC 1 USB”.

When recording all tracks onto the HDD,

select “REC ALL HDD”. When record-

ing one track onto the HDD, select “REC

1 HDD”. When recording all tracks into

a USB device, select “REC ALL USB”.

When recording one track into a USB

device, select “REC 1 USB”.

Press the MULTI JOG dial.

The confirmation message appears.

Ready?

USB 164 MB free

Press the MULTI JOG dial.

Recording starts.

Ready?

HDD 73.4 GB free

1 / 1

Track 03

The confirmation message appears. (The

above is an example when “REC ALL

HDD” is selected.)

14%

Destination of

recording

When recording ends, the CD/HDD

receiver automatically returns to its nor-

mal display for CD operation.

Format

Press [ENTER].

Recording starts.

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording (Transferring Data)—Continued

Recording from Tuner

Recording from Line Input

You can record broadcasting program.

You can record audio from external components con-

nected to LINE1, LINE2, or LINE3. You can't record

audio from external components connected to DIGITAL

OPTICAL IN.

Switch the input source.

Press the [BAND] button to select FM or

AM. You can also use the [INPUT

SELECTOR] button to select the input

source.

Switch the input source.

Press the INPUT [q]/[w] buttons to

select LINE1, LINE2, or LINE3. You

can also use the CD/HDD receiver’s

[INPUT SELECTOR] button to select

the input source.

Tune into the radio stations.

See “Tuning into AM/FM Radio Sta-

tions” on page 32 and “Selecting Preset

Stations” on page 36.

Press the [y3] button according

to the destination of recording.

When recording onto the HDD, press the

HDD REC [y3] button. When record-

to the destination of recording.

Ready?

ing into a USB device, press the USB

REC [y3] button.

When recording onto the HDD, press the

HDD REC [y3] button. When record-

ing into a USB device, press the USB

REC [y3] button.

Start recording.

Press the Play [1] button or [ENTER].

Start the playback of the recording

source.

When recording from a u-capable

component, the CD/HDD receiver auto-

matically starts recording. Otherwise,

first press the Start [1] button or

[ENTER] and then start the playback of

the external component.

00:00:25

FM 76.50MHz

20080820_0034

(The above is an example when the HDD

REC [y3] button is pressed.)

00:00:13

LINE

20080820_0035

Press the Stop [2] button to can-

cel the recording.

Press the Stop [2] button to can-

cel the recording.

“Complete!” will be displayed, and the

recording ends.

During the recording from the u-capa-

ble components, if the playback is

paused or stopped, the CD/HDD receiver

switches to the recording standby mode.

Pressing the button again resumes the

recording.

Complete!

“Complete!” will be displayed, and the

recording ends.

To pause recording, press the Pause [3]

button. To resume recording, press it

again.

Tip:

The title of the recorded program is automatically consists

of date, start time of recording, radio station name (its band

and frequency if it is not preset).

Tip:

The title of the recorded sound is automatically consists of

date, start time of recording, input source name (if the input

source name has been changed in the steps on page 45, the

changed name is used).

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording (Transferring Data)—Continued

Transferring Data

USB Connection

Use the Up and Down [q]/[w] but-

tons to select either of the follow-

ing, and then press [ENTER].

When transferring all tracks in the folder

onto the HDD, select “HDD ALL

COPY”. When transferring one track

onto the HDD, select “HDD COPY”.

When transferring all tracks in the folder

into a USB device, select “USB ALL

COPY”. When transferring one track

into a USB device, select “USB COPY”.

You can also use the MULTI JOG dial on

the CD/HDD receiver to select these

items.

HDD

USB

storage

Digital audio

player

The CD/HDD receiver can transfer the data between its

HDD (hard disk drive) and your USB device (digital

audio player or USB storage device).

Switch the input source to the

transfer source.

Press the INPUT [q]/[w] buttons to

select HDD or USB.

Ready?

HDD 73.4 GB free

The confirmation message appears. (The

above is an example when “HDD ALL

COPY” is selected.)

Select a track or a track list of

album, artist, etc. you want to

transfer.

Press [ENTER].

Data transfer starts.

For selecting tracks, see step 2 in “Play-

ing Selected Tracks” on the pages shown

below:

When selecting tracks in the HDD, see

page 55. When selecting tracks in the

USB, see page 43.

■ Transferring favorite tracks at a time

If you want to record tracks from multiple albums or art-

ists, first add these tracks to the playlist in advance, and

then select the playlist to record the tracks at a time when

recording. See “Creating and Playing the Playlist” on

page 57.

Press the [y3] button according

to the transfer destination.

When transferring to the HDD, press the

HDD REC [y3] button. When transfer-

1 Add tracks to the playlist.

ring to a USB device, press the USB

REC [y3] button.

2 Select a track in the playlist, and press [ENTER].

3 Press [y REC] on the CD/HDD receiver, and

You can also use the y REC button and

MULTI JOG dial on the CD/HDD

receiver.

select “USB ALL COPY”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording (Transferring Data)—Continued

FTP Connection

Select “Open?” and then press

[ENTER].

HDD

Personal computer

FTP Open/Close

<ftp://xxx.xxx.xxx.xxx>

:Open?

After “FTP Starting…” is displayed,

“FTP Stop” appears.

Via FTP connection, you can access the CD/HDD

receiver from your computer and transfer the data from

the HDD to computer and vice versa.

Start Windows Explorer on your

computer, access the CD/HDD

receiver by specifying the IP

address.

Only for personal computers with Microsoft Windows XP Ser-

vice Pack 2, Service Pack 3, or Microsoft Windows Vista

installed.

IP address

Note:

Since the folder name and file name are treated as Uni-

code in the HDD, some folders and files may not be

selected.

Before operating

When Address Bar is not displayed on

Windows Explorer, display Address Bar

according to the Windows operation.

• Set the IP address on the CD/HDD receiver by refer-

ring to “Entering DHCP Settings Manually” on

page 69. If the IP address is not set, the FTP connec-

tion is not available.

If a username and password have been

set in the CD/HDD receiver, also specify

them when accessing. To check the user-

name and password, press the [TOOLS]

button, select “Network”, and then check

the items “FTP Username” and “FTP

Password”.

• If a track is being played or recorded with the

CD/HDD receiver, stop the operation.

Press the [TOOLS] button.

Note:

When accessing by using Internet Explorer,

select “Open FTP Site in Windows

Explorer” on the Page tab after the connec-

tion.

Use the Up and Down [q]/[w] but-

tons to select “Network”, and then

press [ENTER].

Audio

Network

Utility

Transfer the data.

In the same way as the normal file oper-

ation, move the file between the

CD/HDD receiver and the computer.

Close Windows Explorer.

Select “FTP” and then press

[ENTER].

Press [ENTER].

The message “Now Updating…”

appears and the CD/HDD receiver

updates the database in the HDD.

Network

FTP

FTP User name

“Complete!” will be displayed and the

data transfer has been completed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording (Transferring Data)—Continued

Erasing one track or one folder:

Use the Up and Down [q]/[w] buttons to

select “1 Erase?”, and then press

[ENTER].

Erasing Data from USB De vice

The CD/HDD receiver can erase the music track or

album stored on the USB device. For erasing music track

or album from HDD, see “Erasing Music Track or

Album” on page 58. Also see “Operation of Music Data”

on page 27.

Tool

Track 01

:1 Erase?

Switch the input source to USB.

Erasing all items:

Press the INPUT [q]/[w] buttons. You

can also use the CD/HDD receiver’s

[INPUT SELECTOR] button to select

the input source.

Use the Up and Down [q]/[w] buttons to

select “All Erase?”, and then press

[ENTER]. All items displayed in step 2-

3 are erased.

Tool

Track 01

:All Erase?

To cancel erasing, use the Up and Down

[q]/[w] buttons to select “Cancel”, and

then press [ENTER].

Select a track or album you want to

erase.

1. Press the [LIBRARY] button.

2. Use the Up and Down [q]/[w] but-

tons to select the folder, and then

press [ENTER].

The confirmation message “Erase OK?”

appears.

Use the Up and Down [q]/[w] buttons to

select “Yes”, and then press [ENTER].

Songs

Complete!

3. Use the Up and Down [q]/[w] but-

tons to select the track or album.

“Complete!” will be displayed, and the

data has been erased.

Track01

Track02

Press the [TOOLS] button and

then press [ENTER] with “Tool”

selected.

Tool

Record

Audio

Use the Up and Down [q]/[w] but-

tons to select “Song Erase”, and

then press [ENTER].

Tool

Song Erase

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing the HDD

Basic Operations of Playback

Switch the input

source to HDD

(see page 24).

Start playback.

Album name

Press the Play/Pause [1/3] button or Play [1]

CD/HDD receiver

button.

Album name

Track01

The track you played or recorded the last time is played.

01:12

Tip:

Elapsed time of

current track

Format

When you press the remote controller’s HDD [1] button,

the CD/HDD receiver automatically selects an appropriate

input source and starts playback of a track.

Remote

Track name

controller

To pause playback:

Press the remote controller's Pause [3] button or the CD/HDD receiver’s Play/

Pause [1/3] button. To resume playback, press the Play/Pause [1/3] button

again.

To stop playback:

Press the Stop [2] button on the CD/HDD receiver or remote controller.

To select tracks:

Press the [RETURN] button to return to the track list, then press the Up and Down

[q]/[w] buttons to select a track.

To select the previous or next track:

Press the Previous/Next [7]/[6] buttons or turn the MULTI JOG dial on the

CD/HDD receiver to select the previous or next track.

To fast forward or fast reverse:

Press the Fast Reverse/Fast Forward [5]/[4] buttons during playback or

pause. Where you want to start playback, release the button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing the HDD—Continued

Using Alphabetic Search

Playing Selected Tracks

During the list display, you can search tracks in the

alphabetic order by pressing the remote controller’s

number buttons.

Among enormous recorded music files in the HDD of

the CD/HDD receiver, you can easily search the desired

one by artist name, album name, title, or playlist.

Example: Searching items starting with C

1 Press the [2] button.

Switch the input source to HDD.

When there is an item starting with A, it is selected.

If not, the search is continued in the order of B➔C.

Press the INPUT [q]/[w] buttons. You

can also use the CD/HDD receiver’s

[INPUT SELECTOR] button to select

the input source.

2 Press the button (repeatedly).

Press the button repeatedly until the target character

is selected. Each time the button is pressed, the

character to be searched switches in the order of

A➔B➔C➔A.

Note:

Alphabetic Search can only operate on the ARTIST list,

ALBUM list, and TRACK list displayed by selecting each

category of ARTIST, ALBUM, and TRACK from the

library menu. It does not operate on other list screens.

Select the track you want to play.

1 Press the [LIBRARY] button.

2 Use the Up and Down [q]/[w]

buttons to select the category you

want to search, and then press

[ENTER].

Using Jump Mode

With the Jump Mode, you can quickly locate your favor-

ite tracks even when the numerous data such as albums

and artists are contained in the list. There are three

modes: L (Large), M (Medium), and S (Small).

Artist

Normally, the selection item is shifted one by one. How-

ever, in the Jump Mode, some selection items are

skipped in the list. The L (Large) mode has the largest

skipping range, and S (Small) mode has the smallest.

Album

Track

Playlist

To activate the Jump Mode:

During the list display, press the Left and Right [e]/[r]

buttons to set the desired mode.

Jump Mode : Large

Jump mode indicator

Notes:

BGM

• Some modes cannot be selected depending on the length

of the list display.

(See page 57.)

• Even in the same mode, the skipping range varies

depending on the length of the list (the range is adjusted

automatically).

Tuner recording

(Radio)

Line recording (Con-

nected components)

3 Use the Up and Down [q]/[w]

buttons to select the track.

Press [ENTER] to start playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing the HDD—Continued

Switching the Display

You can switch the display by pressing the remote con-

troller’s [DISPLAY] button repeatedly.

During the list display

2-line display

Track 01

Track 02

3-line display

Track 01

Track 02

Track 03

During stop

Track number/

Total tracks

Artist name

Track 01

00:00

1/14

Track name

Album name

Format

Album name

Track 01

00:00

1/14

Album name

Track 01

MP3

128 kbps

Bit rate

Format

During playback and pause

Album name

Track 01

00:08

Elapsed time of

current track

Progress bar

Artist name

Track 01

00:48

1/14

Elapsed time of

current track

Track number/

Total tracks

Artist name

Track 01

MP3

128 kbps

Format

Bit rate

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing the HDD—Continued

Various Playback Modes

PLAYLIST REG

Creating and Playing the Playlist

You can select your favorite tracks in numerous music

files in the HDD and add them to the playlist.

BGM MODE 1

■ Adding a track to the playlist

q / w

ENTER

Select a track (in the HDD) you

want to add to the playlist.

Track 01

Track 02

REPEAT

RANDOM

Press the [PLAYLIST REG] but-

ton.

BGM Playback

Tips:

• You can create a playlist of up to

60,000 tracks.

• You can also press the [TOOLS] button

and select “Add Playlist” to add the

track.

The music files* recorded in the HDD can be played

repeatedly in random order with one button. It is conve-

nient when you want to play music as BGM.

Except for the music files recorded from FM/AM or external

components.

• You can also use the CD/HDD

receiver’s REC button to add the track.

Press the BGM MODE [1] button.

You can also press the [LIBRARY] button and select

“BGM” to start BGM playback (see page 55).

Use the Up and Down [q]/[w] but-

tons to select “PLAYLIST 1”, and

then press [ENTER].

PLAYLIST

Canceling BGM playback

To cancel BGM playback, press the BGM MODE [1]

Tip:

button again.

When you select “PLAYLIST ALL” all

tracks in the folder (album) are added.

Repeat/Random Playback

With random playback, selected tracks can be played in

random order. With repeat playback, tracks or one track

can be played repeatedly. See “Random Playback” and

“Repeat Playback” on page 31.

Use the Up and Down [q]/[w] but-

tons to select a desired playlist,

and then press [ENTER].

PlayList1

PlayList2

Press the [RANDOM] button or the [REPEAT] button

(repeatedly).

Tip:

“Complete!” will be displayed, and the

selected track has been added to the

playlist.

The “REPEAT” indicator on the display means that all

tracks in the current list (tracks, artist, album or playlist)

are played repeatedly.

The “REPEAT 1” indicator means that only the selected

track is played repeatedly.

■ Playing the playlist

1 Press the remote controller’s INPUT [q]/[w]

Note:

buttons to switch the input source to HDD.

During the random playback, you cannot operate the

[LIBRARY] button and [RETURN] button, and cannot

select tracks by specifying the track number. To perform

these operations, cancel the random playback.

2 Press the PL A Y LIST [q ]/[w ] buttons.

Each time the button is pressed, the CD/HDD

receiver changes the playlist and starts playback.

Tip:

A playlist name can be changed afterwards. See “Editing

a Playlist Name” on page 61.

Download from Www.Somanuals.com. All Manuals Search And Download.

Editing Tracks and Playlists in the HDD

The tracks saved in the HDD can be edited as follows.

Erasing one track:

• Erasing music track or album

• Editing track information

• Removing tracks from the playlist

• Editing a playlist name

Use the Up and Down [q]/[w] buttons

to select “1 Erase?”, and then press

[ENTER].

Tool

Track 01

:1 Erase?

Erasing Music Track or Album

You can erase music track or album in the HDD.

Erasing all tracks (an entire album):

Use the Up and Down [q]/[w] buttons

to select “All Erase?”, and then press

[ENTER].

Note:

Once erased, the tracks cannot be recovered. Confirm the

tracks again before actually erasing them. Also see

“Operation of Music Data” on page 27.

Tool

Track 01

:All Erase?

Switch the input source to HDD.

Press the INPUT [q]/[w] buttons. You

can also use the CD/HDD receiver’s

[INPUT SELECTOR] button to select

the input source.

“Complete!” will be displayed, and the

track or album has been deleted.

Editing Track Information

The track information (artist name, album name, title)

recorded in the HDD can be edited. The CD/HDD

receiver temporarily stores edited content in the buffer.

When editing the same content repeatedly, you can eas-

ily paste the stored content. It is convenient for such

cases as changing the artist name of multiple tracks into

the same one.

Select a track or album you want

to erase.

Press the [LIBRARY] button and select

the category you want to search such as

artist, album, or track.

Switch the input source to HDD.

Tip:

Press the INPUT [q]/[w] buttons. You

can also use the CD/HDD receiver’s

[INPUT SELECTOR] button to select

the input source.

Even when erasing an entire album,

you need to select any track in the

album.

Select a track you want to edit.

Press the [TOOLS] button and

then press [ENTER] with “Tool”

selected.

Press the [LIBRARY] button and select

the category you want to search such as

artist, album, or track.

Tool

Record

Audio

Use the Up and Down [q]/[w] but-

tons to select “Song Erase”, and

then press [ENTER].

Press the [TOOLS] button and

then press [ENTER] with “Tool”

selected.

Tool

Edit Name Tag

Song Erase

Tool

Record

Audio

Download from Www.Somanuals.com. All Manuals Search And Download.

Editing Tracks and Playlists in the HDD—Continued

Use the Up and Down [q]/[w] but-

Uppercase letters

Lowercase letters

Numbers and symbols

tons to select “Edit Name Tag”,

and then press [ENTER].

Umlaut letters and symbols

£]

Tool

[Rename Playlist]

Edit Name Tag

Selecting letters:

Press the number buttons repeatedly to

select the available letters. For exam-

ple, press the [2] button repeatedly to

select: A, B, or C.

Use the Up and Down [q]/[w] but-

tons to select “Name Edit?”, and

then press [ENTER].

Press the [0] button repeatedly to

select: 0 or (space)

After you select a desired character,

move to the next input position by press-

Tool

Edit Name Tag

:Name Edit?

ing the Left and Right [

]/[ ] buttons.

Selecting numbers and symbols:

Tip:

Use the number buttons to select numbers.

When you want to edit the following

items with the same content as last time,

the content stored in the buffer can be

pasted. Select one of the following:

“Artist Name Copy?” for editing

artist name

Press the [>10] button

repeatedly to select: (space)

. / * - , ! ? & ’ ( )

After you select a desired

character, move to the next input posi-

tion by pressing the Left and Right [e]/

[r] buttons.

“Album Name Copy?” for editing

album name

Notes:

“Artist&Album Copy?” for editing

artist and album names

When “Complete!” is displayed, the

input has been completed. If “Impossi-

ble” is displayed, input failed. Edit

again in the following steps.

• Not all of the symbols can be entered

by using the number buttons. Use the

Up and Down [q]/[w] buttons to select

from the full range of symbols.

• Up to 64 characters can be input.

Deleting/editing characters:

Inserting a new character:

Deleting preset’s name:

See page 40.

To cancel the Name Edit function, press

the [RETURN] button.

Use the Up and Down [q]/[w] but-

tons to select an item you want to

edit, and then press [ENTER].

“Edit:Artist Name” for editing artist

name

“Edit:Album Name” for editing

album name

“Edit:Title Name” for editing track

name

Press [ENTER] to finish editing.

“Complete!” will be displayed, and the

track information has been changed.

Note:

The CD/HDD receiver enters the char-

acter edit mode.

The message “Waiting…” may appear

while the track information is being

changed.

Tool

For this change, it may take from sev-

eral tens of seconds to a few minutes

depending on the track file size.

Edit Name Tag

A ]

Character

group

Input position

Available Characters

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

a b c d e f g h i j k l m n o p q r s t u v w x y z

0 1 2 3 4 5 6 7 8 9

Press the [CAPS] button repeat-

edly to select one of the following

character groups:

;

(

)

’

”

(space)

(insert)

Each time you press the button, the

character group switches.

À Á Â Ã Ä Å Æ Ç È É Ê Ë Ì Í Î Ï Ð Ñ Ò Ó Ô Õ Ö × Ø Ù Ú

Û Ü Ý Þ ß à á â ã ä å æ ç è é ê ë ì í î ï ð ñ ò ó ô õ ö ÷ ø ù

¼ ½ ¾ ¿

Download from Www.Somanuals.com. All Manuals Search And Download.

Editing Tracks and Playlists in the HDD—Continued

Removing Tracks from the Playlist

Use the Up and Down [q]/[w] but-

tons to select “Clear Playlist”,

and then press [ENTER].

Even when a track in the playlist is removed, the music

file itself is not deleted.

Tool

Clear Playlist

[Rename Playlist]

Switch the input source to HDD.

Press the INPUT [q]/[w] buttons. You

can also use the CD/HDD receiver’s

[INPUT SELECTOR] button to select

the input source.

Removing one track:

Use the Up and Down [q]/[w] buttons

to select “1 Clear?”, and then press

[ENTER].

Select the playlist.

Tool

[Track 01

]

1 Press the [LIBRARY] button.

:1 Clear?

2 Use the Up and Down [q]/[w]

buttons to select “PLAYLIST”,

and then press [ENTER].

Removing all tracks in the

playlist:

Use the Up and Down [q]/[w] buttons

to select “All Clear?”, and then press

[ENTER].

PLAYLIST

3 Use the Up and Down [q]/[w]

buttons to select a desired playlist,

and then press [ENTER].

Tool

[Track 01

]

:All Clear?

PlayList1

PlayList2

Complete!

“Complete!” will be displayed, and the

track has been removed from the

playlist.

Use the Up and Down [q]/[w] but-

tons to select the track you want

to remove.

Track 01

Track 02

Press the [TOOLS] button and

then press [ENTER] with “Tool”

selected.

Tool

Record

Audio

Download from Www.Somanuals.com. All Manuals Search And Download.

Editing Tracks and Playlists in the HDD—Continued

Editing a Playlist Name

Uppercase letters

Lowercase letters

Numbers and symbols

Although a playlist is initially named as PlayList 1, Play-

List 2…, PlayList 23, the name can be changed as you

like.

Switch the input source to HDD.

Umlaut letters and symbols

£]

Press the INPUT [q]/[w] buttons. You

can also use the CD/HDD receiver’s

[INPUT SELECTOR] button to select

the input source.

Selecting letters:

Press the number buttons repeatedly to

select the available letters. For exam-

ple, press the [2] button repeatedly to

select: A, B, or C.

Press the [0] button repeatedly to

select: 0 or (space)

After you select a desired character,

move to the next input position by

pressing the Left and Right [e]/[r]

buttons.

Select the playlist.

1 Press the [LIBRARY] button.

2 Use the Up and Down [q]/[w]

buttons to select “PLAYLIST”,

and then press [ENTER].

PLAYLIST

Selecting numbers and symbols:

Use the number buttons to select numbers.

3 Use the Up and Down [q]/[w]

buttons to select a desired playlist,

and then press [ENTER].

Press the [>10] button

repeatedly to select: (space)

. / * - , ! ? & ’ ( )

After you select a desired

character, move to the next input posi-

tion by pressing the Left and Right [e]/

[r] buttons.

PlayList1

PlayList2

Notes:

Press the [TOOLS] button and

• Not all of the symbols can be entered

by using the number buttons. Use the

Up and Down [q]/[w] buttons to select

from the full range of symbols.

• Up to 32 characters can be input.

then press [ENTER] with “Tool”

selected.

Tool

Record

Audio

Deleting/editing characters:

Inserting a new character:

Deleting preset’s name:

See page 40.

To cancel the Rename Playlist function,

press the [RETURN] button.

Use the Up and Down [q]/[w] but-

tons to select “Rename Playlist”,

and then press [ENTER].

The CD/HDD receiver enters the char-

acter input mode.

Press [ENTER] to finish editing.

“Complete!” will be displayed, and the

playlist name has been changed.

Tool

Edit Name Tag

A ]

Available Characters

Character

group

Input position

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

a b c d e f g h i j k l m n o p q r s t u v w x y z

0 1 2 3 4 5 6 7 8 9

Press the [CAPS] button repeat-

edly to select one of the following

character groups:

Each time you press the button, the

character group switches.

”

;

(

)

’

(space)

(insert)

À Á Â Ã Ä Å Æ Ç È É Ê Ë Ì Í Î Ï Ð Ñ Ò Ó Ô Õ Ö × Ø Ù Ú

Û Ü Ý Þ ß à á â ã ä å æ ç è é ê ë ì í î ï ð ñ ò ó ô õ ö ÷ ø ù

¼ ½ ¾ ¿

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the Clock

Setting AccuClock to Use a Specific Station

The AccuClock function normally uses the FM station with the strongest signal to set the clock. However, if the clock

cannot be set properly using that station, you can specify which FM station the AccuClock function should use. This

must be an FM station that supports RDS CT (Clock Time) information.

When you’ve selected the station,

press [ENTER].

Press the [TIMER] button.

Remote

controller

While the clock is being set, “Wait…”

flashes on the display. It may take a few

minutes to set the clock. When the clock

has been set, the message “Clock

Adjusted” scrolls across the display, then

the day and time are displayed for a

while.

Press [ENTER] with “Clock”

selected.

Notes:

• If the clock is not set correctly, specify

another FM station and try again or set

the clock manually (see page 63).

• The AccuClock function automatically

updates the clock every day. If you don’t

want it to, you can turn off the Accu-

Clock function (see page 23).

Clock

Timer 1

Timer 2

Use the Up and Down [q]/[w] but-

tons to select “AccuClock”, and

then press [ENTER].

Press [ENTER].

The frequency flashes on the display.

Clock

RDS-CT Station

: FM 87.50MHz

The asterisks indicate that the

AccuClock function is on.

Use the Fast Reverse and Fast For-

ward [5]/[4] buttons to tune

into the FM station.

Tip:

If you press the [ENTER] button instead of

using the Fast Reverse and Fast Forward

[5]/[4] buttons, the CD/HDD

receiver will automatically search for a

suitable station.

The RDS indicator appears when tuned

into a station that supports RDS.

The RDS indicator will flash while the

CD/HDD receiver searches for a station

and light up continuously when a station

is found.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the Clock—Continued

Setting the Clock Manually

The time can be displayed in 24-hour format.

Press [ENTER].

The time setting procedure starts.

TIMER

Number

buttons

Use the remote controller’s num-

ber buttons to set the time.

Enter a four-digit number, hour(00-23)

and minute(00-59). You can also use the

Up and Down [q]/[w] buttons to enter

the time.

ENTER

q/w/e/r

Clock

Adjust Time

0:00

Press the [TIMER] button.

If you press the remote controller’s [>10]

button, you can move the clock forward/

backward 12 hours.

Clock

Timer 1

Timer 2

Press [ENTER].

“Complete!” will be displayed and the

clock is set.

Press [ENTER] with “Clock”

selected.

The sub-menu appears and the CD/HDD

receiver enters clock setting mode.

Clock

Tip:

Adjust Mode

:Manual Adjust

To cancel the clock setting, press the [RETURN] button

repeatedly.

Press [ENTER] with “Manual

Adjust” selected.

The clock setting procedure starts.

Displaying the Day and Time

To display the day and time, press the remote controller’s

[CLOCK CALL] button.

If the CD/HDD receiver is on Standby, the time is dis-

played for a certain time.

Use the Up and Down [q]/[w] but-

tons to set the year.

CLOCK CALL

Clock

Adjust Date

:2008. 01. 01 (TUE)

You can also use the remote controller’s

number buttons to enter the year.

Press [ENTER].

Use the Up and Down [q]/[w] but-

tons to set the date.

You can also use the remote controller’s

number buttons to enter the date.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Timers

The CD/HDD receiver has three timers: the sleep timer

for turning the CD/HDD receiver off after a specified

period, the play timer for automated playback, and the

record timer for automated recording.

Up to four programmable timers are available for the

play and record timers.

Using the Sleep Timer

With the sleep timer, you can set the CD/HDD receiver

so that it automatically turns off after a specified period.

This timer is convenient when you want to fall asleep

while listening to music.

The timers can be used with other Onkyo components

that are connected to the CD/HDD receiver via u (see

page 19 for hookup details).

Press the [SLEEP] button repeat-

edly to select the required sleep

time.

The SLEEP indicator and “Sleep 90

min” appear on the display, as shown.

With the [SLEEP] button, you can set

the sleep time from 90 to 10 minutes in

10 minute increments.

SLEEP

TIMER

Sleep 90 min

SLEEP indicator

To set the sleep time in 1 minute incre-

ments from 99 to 1, use the Up and

Down [q]/[w] buttons during the sleep

time is displayed. The sleep time

appears on the display for about 8 sec-

onds, then the previous display reap-

pears.

Checking the Remaining Sleep Time

To check the remaining sleep time, press the [SLEEP]

button.

Note that if you press the [SLEEP] button while the

remaining sleep time is 10 minutes or less, the sleep

timer is canceled..

Canceling the Sleep Timer

To cancel the sleep timer, press the [SLEEP] button

repeatedly until “Sleep Off” appears and the SLEEP

indicator disappears.

Note:

During recording, the sleep timer can be set. When the sleep

time period has expired during recording, the CD/HDD

receiver will cancel the recording and enter the Standby

mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Timers—Continued

Set the day and time.

Using the Play Timer

Use the Up and Down [q]/[w] buttons

to select “Once” or”Every”, and then

press [ENTER].

Select “Once” for on-off operation.

Select “Every” to perform the same

operation every week. Use the Up and

Down [q]/[w] buttons to set the day

and then press [ENTER].

If you selected “Once”:

Use the Up and Down [q]/[w] buttons

to select the day, and then press

[ENTER].

With the play timer, you can automatically turn on the

CD/HDD receiver, start playback, and turn off the CD/

HDD receiver at a specified time. This timer is conve-

nient to use as a morning alarm.

Before setting the timer:

• You must set the clock before you can set the timers

(page 62).

• Before setting a timer to turn on the radio, you must

preset the station you want to use (see pages 34 and

35).

Press the [TIMER] button.

If you selected “Every”:

Use the Up and Down [q]/[w] buttons

to select the day, “Everyday”, or “Days

Set”, and then press [ENTER].

You can select the following:

MON

TUE

WED

THU

FRI

Select a timer number.

Use the Up and Down [q]/[w] buttons

to select Timer1, 2, 3, or 4 and then

press [ENTER]. The Timer indicator

lights up and the selected timer number

flashes on the display.

Days Set

Everyday

SAT

SUN

If you selected “Days Set”, use the Up

and Down [q]/[w] buttons to select the

first day, and then press [ENTER]. Use

the Up and Down [q]/[w] buttons to

select the last day, and then press

[ENTER]. You can select only consec-

utive days.

TIMER indicator

Timer 1

Timer Mode

:Off

Set the On time and Off time.

Use the Up and Down [q]/[w] buttons

to select the time, and then press

[ENTER]. You can also use the number

buttons.

TIMER number

Set the status of the timer.

Use the Up and Down [q]/[w] buttons

to select “On”, and then press

[ENTER].

Use the Up and Down [q]/[w] but-

tons to specify the CD/HDD

receiver’s volume level, and then

press [ENTER].

If you selected “Last”, the volume is set

at the same level as the last playback. If

you selected “Mute”, the output is

muted. You can also set the volume

from “01” through “41” to “Max”.

Set the type of the timer.

Use the Up and Down [q]/[w] buttons

to select “Play”, and then press

[ENTER].

Select the source.

Use the Up and Down [q]/[w] buttons

to select the source, and then press

[ENTER].

You can select the following sources:

HDD, CD, USB, FM, AM, LINE,

TAPE, DOCK, or DIGITAL

Select a preset for FM or AM.

Press the [ON/STANDBY] button

to set the CD/HDD receiver to

Standby.

Note:

Be sure to set the CD/HDD receiver to

Standby, otherwise the timed operation

will not work.

Notes:

• When four timers have already been programmed, cancel

one of the timers already set, and then set a new one.

• Some operation cannot be done about one minute before

the On time of the timer.

See page 67 for canceling, changing, and deleting the

play timer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Timers—Continued

Set the day and time.

Using the Record Timer

Use the Up and Down [q]/[w] buttons

to select “Once” or “Every”, and then

press [ENTER].

Select “Once” for on-off operation.

Select “Every” to perform the same

operation every week. Use the Up and

Down [q]/[w] buttons to set the day

and then press [ENTER].

If you selected “Once”:

Use the Up and Down [q]/[w] buttons

to select the day, and then press

[ENTER].

With the record timer, you can automatically turn on the

CD/HDD receiver, start recording, and turn off the CD/

HDD receiver at a specified time. This timer is conve-

nient when you want to record music or programs while

you are out, or record late-night broadcasting programs.

Before setting the timer:

• You must set the clock before you can set the timers.

Before setting a timer to turn on the radio, you must

preset the station you want to use (see pages 34 and 35).

•

Press the [TIMER] button.

If you selected “Every”:

Use the Up and Down [q]/[w] buttons

to select the day, “Everyday”, or “Days

Set”, and then press [ENTER].

You can select the following:

Select a timer number.

Use the Up and Down [q]/[w] buttons

to select Timer1, 2, 3, or 4 and then

press [ENTER]. The Timer indicator

lights up and the selected timer number

flashes on the display.

MON

TUE

WED

THU

FRI

Days Set

Everyday

SAT

SUN

If you selected “Days Set”, use the Up

and Down [q]/[w] buttons to select the

first day, and then press [ENTER]. Use

the Up and Down [q]/[w] buttons to

select the last day, and then press

[ENTER]. You can select only consec-

utive days.

TIMER indicator

Timer 1

Timer Mode

:Off

TIMER number

Set the On time and Off time.

Use the Up and Down [q]/[w] buttons

to select the time, and then press

[ENTER]. You can also use the number

buttons.

Set the status of the timer.

Use the Up and Down [q]/[w] buttons

to select “On”, and then press

[ENTER].

Set the type of the timer.

Use the Up and Down [q]/[w] buttons

to select “Rec”, and then press

[ENTER].

Set the volume.

Use the Up and Down [q]/[w] buttons

to adjust the volume, and then press

[ENTER].

Select the source you want to play.

Use the Up and Down [q]/[w] buttons

to select the source and then press

[ENTER].

You can select the following sources:

FM, AM, or LINE

Press the [ON/STANDBY] button

to set the CD/HDD receiver to

Standby.

Note:

Be sure to set the CD/HDD receiver to

Standby, otherwise the timed operation

will not work.

Select a preset for FM or AM.

Select the source you want to

record.

Use the Up and Down [q]/[w] buttons

to select the source, and then press

[ENTER].

You can select the following sources:

HDD, USB, or T A PE

When selecting an external component,

you need to use an u-capable compo-

nent and set the Input Display name to

match the type of component (see

page 45).

Notes:

• When four timers have already been programmed, cancel

one of the timers already set, and then set a new one.

• Some operation cannot be done about one minute before

the On time of the timer.

• To ensure that the first few seconds of a program are

recorded, set the On time slightly ahead of the program’s

start time (about one minute).

To hear what’s being recorded during recording:

When the record timer starts from the Standby mode, the

output of the CD/HDD receiver is muted. Press the

[MUTING] button or VOL [q]/[w] button to unmute the

CD/HDD receiver.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Timers—Continued

Canceling a Running Play/Record Timer

The play or record timer can be canceled during a pro-

cess of timer playback or timer recording, without stop-

ping the playback or recording.

1 Press the [TIMER] button.

2 Select the timer you want to cancel, and then press

the [ENTER].

The timer setting display appears.

3 Select “Off” in the Timer Mode, and then press

the [ENTER].

4 Press the [RETURN] button to return to the

previous display.

Checking/Changing Timer Settings

1 Press the [TIMER] button.

2 Select the timer you want to check or change, and

then press the [ENTER].

The timer setting display appears. Check the setting

items while switching it by pressing the [ENTER]

repeatedly. When the setting item you want to

change is displayed, change it.

3 When the check is completed, press the [ENTER]

to close.

Turning Off a Timer

Once a timer has been programmed, you can turn it off

as necessary. For example, while you’re on holiday, you

may want to turn off the timer you use as an early morn-

ing alarm.

1 Press the [TIMER] button.

2 Select the timer you want to turn off, and then

press the [ENTER].

The timer setting display appears.

3 Select “Off” in the Timer Mode, and then press

the [ENTER].

The timer number of the selected timer disappears

from the display.

When the last remaining timer was turned off, the

“TIMER” indicator will also disappear.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Setup

Network Configuration

When your computer cannot be connected to the Internet, or you want to set the IP address manually, set the following

network configuration. When setting it manually, input the values (alphanumeric characters) according to the setting of

your broadband router currently in use. The necessary setting items vary depending on the Internet Service Provider

(ISP). See the materials provided from your ISP for details.

Setting item

IP Address

Description

Example

An Internet Protocol (IP) address is a numerical identification (logical

address) that is assigned to computers and network devices connected to

the network (TCP/IP network).

192.168.xxx.xxx

In computer networks based on the Internet protocol suite, a subnet is a

portion of the network’s computers and network devices. A subnet mask

can be used to specify which portion of the IP address should be used as

the network number for the subnet.

Subnet Mask

255.255.xxx.xxx

192.168.xxx.xxx

A default gateway is a node (a router) on a computer network that serves as

an access point to another network. All internet traffic passes through the

gateway.

In homes, the gateway is usually the ISP-provided device that connects the

user to the Internet, such as a DSL or cable modem.

Gateway Address

(Default gateway)

The Domain Name System (DNS) associates various information with

domain names. A DNS server is a special type of computer on the Internet

used to support the DNS. ISPs give their customers the public IP address

of the DNS server.

DNS Address

(DNS server address)

(primary)

In computer networks, a proxy server acts an intermediate gateway

between you and your Internet connection. The proxy server sends the

requests of its clients by forwarding requests to other servers. The proxy

server also provides network firewall, connection sharing, and caching

technology for private networks. A client connects to the proxy server,

requesting some service, such as a file, connection, web page, or other

resource, available from a different server. The proxy server provides the

resource by connecting to the specified server and requesting the service

on behalf of the client.

Proxy

proxy.xxx.ne.jp

DHCP is a protocol used by networked devices (clients) to obtain the

parameters necessary for operation in an Internet Protocol network. ISPs

usually use DHCP so that customers can reduce system administration

workload and join the Internet with minimum effort.

In DHCP, a computer joins the network without having a pre-configured IP

address. IP addresses are uniquely assigned to devices, then released and

renewed these addresses as devices leave and re-join the network.

DHCP

(Dynamic host

configuration

protocol)

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Setup—Continued

Entering DHCP Settings Manually

Setting the Proxy

You can enter DHCP settings such as the IP address, sub-

net mask, default gateway, or DNS server manually. Fol-

low these steps when you want to assign the fixed IP

address for network connection, or to assign the DNS

server address specified by your ISP.

Configure the Proxy setting when your ISP specifies it.

If not specified, the Proxy setting is not necessary.

1 Press the [TOOLS] button.

2 Use the Up and Down [q]/[w] buttons to select

“Network”, and then press [ENTER].

1 Press the [TOOLS] button.

3 Use the Up and Down [q]/[w] buttons to select

2 Use the Up and Down [q]/[w] buttons to select

“Proxy”, and then press [ENTER].

“Network”, and then press [ENTER].

4 Use the Up and Down [q]/[w] buttons to select

3 Use the Up and Down [q]/[w] buttons to select

“On”, and then press [ENTER].

“DHCP”, and then press [ENTER].

5 Use the Up and Down [q]/[w] buttons to select

settings you want to enter, and then press

[ENTER].

4 Use the Up and Down [q]/[w] buttons to select

“Manual”, and then press [ENTER].

5 Use the Up and Down [q]/[w] buttons to select

settings you want to enter, and then press

[ENTER].

6 Enter the settings.

Use the number buttons to enter, and then press

[ENTER] to save the settings.

6 Enter the settings.

Use the number buttons to enter, and then press

[ENTER] to save the settings.

Network

Proxy Port

Network

IP Address

:192. 168. XXX. XXX

Network

Proxy Address

proxy. XXX. jp

Network

Subnet Mask

:255. 255. XXX. XXX

Network

Proxy UserName

proxy

Network

GatewayAddress

:192. 168. XXX. XXX

Network

Proxy Password

Network

7 Press the [RETURN] button.

DNS Address

:192. 168. XXX. XXX

The confirmation message appears. Select “OK” in

the “Save Setting?” message, and then press the

[ENTER]. After the “Saving Settings” message is

displayed, the screen returns to the menu list.

7 Press the [RETURN] button.

The confirmation message appears. Select “OK” in

the “Save Setting?” message, and then press the

[ENTER]. After the “Saving Settings” message is

displayed, the screen returns to the menu list.

Download from Www.Somanuals.com. All Manuals Search And Download.

Disc Notes

Supported Discs

Disc Content Organization

The CD/HDD receiver supports the following discs

(8 cm and 12 cm).

■ Audio CD

Audio CDs contain tracks.

Format or file

type

Track 1 Track 2 Track 3 Track 4 Track 5

Disc

Logo

Audio CD

WAV (PCM)

Audio CD

Audio CD,

MP3, WMA,

AAC

■ Data CD

CD-R

Data CDs contain MP3, WMA, AAC, or WAV files

organized into folders.

Audio CD,

MP3, WMA,

AAC

CD-RW

Folder 1

File 2

Folder 2

File 1 File 2

File 1

File 3

Notes:

• The CD/HDD receiver does not play discs that have not

been finalized.

Data CD (CD-R/CD-RW)

• The playback may not be possible depending on the disc

characteristics or recording state of a CD-R/CD-RW disc.

• The PHOTO CD, data session of CD Extra disc, and

super audio CD cannot be played.

• The CD-R/CD-RW with music CD and MP3 file mixed

cannot be played.

Precautions on DualDiscs

The CD/HDD receiver is designed to play discs in con-

formity with the CD standards. The DualDisc is a two-

sided disc made up of a DVD-standard-compatible side

and a music-specific side. However, the music-specific

side is not compatible with the CD standards, so it may

not be played with the CD/HDD receiver.

Don’t use discs with an unusual shape, such as those

shown below, as you may damage the CD/HDD receiver.

DualDisc is a trademark owned by the Recording Indus-

try Association of America (RIAA).

Playback of Copy-protected Audio CDs

Tip:

Some audio CDs use copy protection that doesn't con-

form to the CD standards. Since these are nonstandard

discs, they may not play properly in the CD/HDD

receiver.

For the CD recording format, see the instruction manual

of your CD-R/RW drive or the disc burner.

Download from Www.Somanuals.com. All Manuals Search And Download.

Disc Notes—Continued

Handling Discs

Storing Discs

• Never touch the underside of a disc. Always hold discs

by the edge, as shown.

• Don't store discs in places subject to direct sunlight or

near heat sources.

• Don't store discs in places subject to moisture or dust,

such as in a bathroom or near a humidifier.

• Always store discs in their cases and vertically. Stack-

ing, or putting objects on unprotected discs may cause

warping, scratches, or other damage.

Underside

• Never attach adhesive tape or sticky labels, or write

letters even on the label side, much less on the under-

side.

• Never scratch the CD surfaces.

Precautions on Rental Discs

Don't use discs that have residue from adhesive tape,

rental discs with peeling labels, or discs with custom-

made labels or stickers. Doing so may damage the CD/

HDD receiver and you may not be able to remove the

disc properly.

Cleaning Discs

• For best results, keep your discs clean. Fingerprints

and dust can affect the sound quality and should be

removed as follows. Using a clean soft cloth, wipe

from the center outwards, as shown. Never wipe in a

circular direction.

✔

• To remove stubborn dust or dirt, wipe the disc with a

damp soft cloth, and then dry it with a dry cloth.

• Never use solvent-based cleaning fluids, such as thin-

ner or benzine, commercially available cleaners, or

antistatic sprays intended for vinyl records, as they

may damage the disc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playable Formats

pressed, encrypted, and unsynchronized ID3 tags can-

not be displayed.

• The ID3 tag information may be displayed in only 31

characters depending on the file.

Supported Formats

The CD/HDD receiver supports the following formats

for playback.

WAV: (*.wav)

• The CD/HDD receiver supports up to 500 files and

folders per disc. Files and folders in excess of this can-

not be played. Note that if the file and folder structure

is very complicated, the CD/HDD receiver may not be

able to read or play all of the files.

• With CD-ROM, CD-R, and CD-RW discs that contain

many files and folders and files (not limited to music

files), it may take a long time to read the disc. Onkyo

recommend that you include only music files on your

discs, use about 20 folders, and limit folder nesting to

three levels deep.

Sampling rate:

Data size:

32 kHz, 44.1 kHz, 48 kHz

16 bit, 24 bit

WMA: (*.wma)

Format:

Windows Media^®Audio V9.0

(Compliant with WMA9/9.1 standard

audio bit streams encapsulated in ASF

container and backward compatible

with WMA4, WMA4.1, WMA7 &

WMA8; CBR & VBR; Mono & Stereo)

Sampling rate: 8 kHz, 11.025 kHz, 16 kHz, 22.05 kHz,

• The Emphasis is not supported.

• Multisession discs are not supported.

32 kHz, 44.1 kHz, 48 kHz

8-384 kbps and VBR

Bit rate:

■ Levels of Music Files and Playback Order

Albums (folders) or tracks recorded in a data CD or USB

storage device are recognized in hierarchical structure,

and played back in ascending order of 1 to 7 in the exam-

ple below.

MP3: (*.mp3)

Format:

MPEG-2 Audio Layer-3

Sampling rate: 8 kHz, 11 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1kHz,

48kHz

Bit rate:

8-320 kbps and VBR

When an album contains sub albums, tracks in the sub

albums have priority for playback. (Example: Because

album B contains sub album C, track 3 will be played

after track 2 instead of track 6 or 7.)

Depending on the disc burner used during recording of

the music files, the tracks may not be played in the order

shown in the figure.

AAC: (*.m4a)

Format:

MPEG-4 Audio

Sampling rate: 8 kHz, 11 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,

48 kHz

Bit rate:

8-192 kbps and VBR

• The playable format for the iPod is determined in

accordance with the specifications of the iPod. How-

ever, contents recorded at the sampling rate of 32 kHz

cannot be played.

• Some types of AAC files may not be played.

• Music files which are copyright protected cannot be

played.

Example of levels:

Disc or USB

device

1st level 2nd level 3rd level 4th level

Folder

• When a file created in unsupported sampling rate or

bit rates is played, playback may be stopped or

become intermittent, or loud noises or speaker damage

may occur.

• Do not use each specified file extension for a file in a

different format. The CD/HDD receiver tries to play-

back it and this may result in skipped playback, noises

or failure.

File

• In the following cases, the elapsed time of playback

may be different from the actual time.

- When a VBR (Variable Bit Rate) file is played

- When fast reverse or fast forward is performed

• The maximum time that can be displayed for a single

file is 99 minutes and 59 seconds.

• The remaining time cannot be displayed.

• The following ID3 tags are supported: versions 1.0/1.1

and 2.2/2.3/2.4. Versions 2.5 and later are not sup-

ported. Normally, version 2.2/2.3/2.4 tags have prior-

ity and will be displayed.

• For ID3 version 2 tags, the tag information recognized

will be those embedded in the beginning of the file.

Onkyo recommend that you include only title, artist

name, and album name information in ID3 tags. Com-

Note:

For the data CD with music files recorded, the CD/HDD

receiver can display up to eight levels deep. Also, depending

on the restrictions of your personal computer, the display

may be limited.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling External Components

Explanation of buttons for using the Onkyo MD recorder, cassette deck, CD recorder, or RI Dock, when con-

nected to the MD/TAPE jack, DOCK/CDR jack or DIGITAL IN jack of the CD/HDD receiver.

• See page 19 for instructions on connecting the components.

• To control the MD recorder, the Input Display for the MD/TAPE jacks must be set to “MD” (see page 45).

Example: Shows the case of l:

the [RANDOM] button.

• When the cassette deck is connected to the MD/TAPE

jack of the CD/HDD receiver and the input source is

set to “TAPE”, it works as a DOLBY NR button.

• When the CD recorder is connected to the DOCK/

CDR IN/OUT jack of the CD/HDD receiver and the

input source is set to “DOCK”, it works as a SHUF-

FLE button. However, the input source is set to “CD-

R”, it works as a RANDOM button. In the same way,

when the CD recorder is connected to the OPTICAL

DIGITAL IN jack and the input source is set to “CD-

R/dig”, it works as a RANDOM button.

Jack

Input source

MD/TAPE

DOCK/CDR

DOCK

DIGITAL IN

CD-R/dig

TAPE

CD-R

Button

1 ~ 9

10/0

>10

1 ~ 9

10/0

>10

1 ~ 9

10/0

>10

e/r

q/w

ALBUM q/w

CURSOR q/w

5/4

PLAYLIST q/w

CLEAR

5/4

PLAYLIST q/w

5/4

CLEAR

ENTER

CLEAR

ENTER

DISPLAY

7/6

REPEAT

SELECT

BACKLIGHT

7/6

DISPLAY

7/6

REPEAT

DISPLAY

7/6

REPEAT

DISPLAY

7/6

REPEAT

5/4

REV MODE

REPEAT

RANDOM

(PLAY MODE)

RANDOM

DOLBY NR

SHUFFLE*

RANDOM

See the instruction manual for each connected component for details. For column items with no notation, buttons will

not function when pressed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

If you have any trouble using the CD/HDD receiver, look for a solution in this section.

If you can’t resolve the issue yourself, try resetting the CD/HDD receiver before contacting your Onkyo dealer.

To reset the CD/HDD receiver, while holding down the

[ON/STANDBY] button, turn the [MULTI JOG] dial.

HOLD

TURN

ON/STANDBY

MULTI JOG

Power

Can’t turn on the CD/HDD receiver.

• Make sure that the power cord is properly plugged into the wall outlet (see page 22).

• Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.

It takes a time to start after the power is turned on from standby mode.

• It may take approx. 30 seconds for the CD/HDD receiver to start because it shall obtain the IP address automatically

depending on the status of the CD/HDD receiver.

The CD/HDD receiver turns off unexpectedly.

• If the sleep timer has been set and the TIMER indicator is shown on the display, the CD/HDD receiver will turn off

automatically after a specified period (see page 64).

• When timed playback or recording finishes, the CD/HDD receiver automatically switches to Standby mode.

• If the STANDBY indicator is flashing, the built-in amplifier protection circuit has been activated. This can happen if

there’s a short between the positive and negative wires of a speaker cable.

Audio

There’s no sound.

• Make sure the speakers are connected correctly (see page 16).

• Make sure the CD/HDD receiver’s volume control is not set to minimum (see page 24).

• Make sure the correct input source is selected (see page 24).

• Make sure the CD/HDD receiver is not muted (see page 25).

• While headphones are connected, the speakers output no sound (see page 24).

The sound quality is not good.

• Make sure the speaker cables are connected with the correct polarity (see page 16).

• Make sure all audio connecting plugs are pushed in all the way (see page 15).

• The sound quality can be affected by strong magnetic fields, such as that from a TV. Try moving any such devices

away from the CD/HDD receiver.

• If you have any devices that emit high-intensity radio waves near the CD/HDD receiver, such as a cellular phone that’s

being used to make a call, the CD/HDD receiver may output noise.

• The CD/HDD receiver’s precision drive mechanism may emit a faint hissing sound while reading discs during play-

back or when searching for tracks. You may be able to hear this noise in extremely quiet environments. With some

discs, the sound of disc rotation may become louder during recording.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting—Continued

Audio output is intermittent when the CD/HDD receiver is subjected to vibration.

• The CD/HDD receiver is not a portable device. Use it in a location that’s not subject to shock or vibration.

Headphone output is intermittent or there’s no sound.

• This may be due to dirty contacts. Clean the headphones plug. See your headphones’ instruction manual for cleaning

information. Also, make sure that the headphones cable is not broken or damaged.

Audio performance

• Audio performance will be at its best about 10 to 30 minutes after the CD/HDD receiver has been turned on and had

time to warm up.

• Using cable ties to bundle audio cables with speaker or power cables may degrade the sound quality, so don’t do it.

HDD Playback

Can’t play a track.

• Audio sound recorded in an incorrect format cannot be played (see page 72).

Can’t record a CD.

• Make sure the CD conforms to the official CD standard (see page 70).

• The CD/HDD receiver can record only audio CDs to the HDD.

• Make sure the disc is not damaged or dirty.

Can’t record files from USB storage device.

• Up to 10,000 tracks can be recorded at a time. Delete tracks in the USB storage device to 10,000 or less, and then

record them.

Can’t record to digital audio player.

• The CD/HDD receiver can record only to the digital audio player that conforms to the USB mass storage class.

• The CD/HDD receiver may not be recordable to some MP3 players.

CD Playback

Playback jumps.

• The CD/HDD receiver is being subjected to vibration or the disc is scratched or dirty (see page 71).

The disc will not play.

• Make sure the loaded disc is supportable by the CD/HDD receiver (see page 70).

• Make sure the disc has been loaded correctly, with the label-side facing up.

• Check to see if the surface of the disc is dirty (see page 71).

• If condensation is suspected, turn on the CD/HDD receiver and leave it for 1 hour before playing any discs.

• Some CD-R/RW discs may not be playable (see page 70).

Can’t play tracks in the order recorded on a CD.

• Cancel the repeat and random playback (see page 31).

Can’t retrieve music file information.

• Music information of only audio CDs can be retrieved.

• For retrieving music information of audio CDs, Internet connection is required (see page 21).

• When the “Gracenote Service” is set to “Off”, you need to retrieve the music information manually.

It takes a long time for playback to start.

• It may take the CD/HDD receiver a while to read CDs that contain many tracks or files.

Can’t play music files.

• Use only ISO 9660 Level 1, Level 2, or Joliet compliant discs.

• MP3 files without a “.mp3” or “.MP3” filename extension are not recognized. AAC files without a “.m4a” or “.M4A”

filename extension are not recognized. WAVE files without a “.wav” or “.WAV” filename extension are not recog-

nized. If the file extension is added to a file in a different format, the CD/HDD receiver tries to playback it and this

may result in skipped playback, noises or failure.

• The CD-R/CD-RW with music CD and music file mixed cannot be played (see page 70).

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting—Continued

Playback of audio CD with copy protection function (copy control function)

Noise or skip occurs during playback / Disc is not recognized and “NO DISC” is displayed / First track

is not played / Music scan takes longer time than usual / Playback starts from halfway / Some parts

cannot be played / Playback stops halfway / Display error occurs

• The audio CD has a copy protection function (copy control function). Some audio CDs use copy protection that

doesn't conform to the official CD standard. Since these are nonstandard discs, they may not play properly in the CD/

HDD receiver.

Tuner

Reception is noisy, stereo FM reception suffers from hiss, the Auto Preset function doesn’t preset all

stations, or the FM STEREO indicator doesn’t light up when tuned to a stereo FM station.

• Check the antenna connections (see page 17).

• Change the position of the antenna (see page 32).

• Move the CD/HDD receiver away from a nearby TV or computer.

• Move power cords and speaker cables as far away as possible from the tuner’s antenna.

• Cars or airplanes can cause noisy interference.

• The radio signal will be weakened if it has to pass through a concrete wall before reaching the antenna.

• Try setting FM mode to mono (see page 36).

• When listening to an AM station, noise may be heard when you operate the remote controller.

• If none of the above improves the reception, install an outdoor antenna (see page 18).

If a power outage occurs or the power cable is disconnected:

• If the preset stations are lost, preset them again (see page 34).

• The clock and timer settings will be lost. Set the clock and timers again (see page 62).

Can’t adjust the frequency of the radio.

• Use the Fast Reverse and Fast Forward [5]/[4] buttons to change the frequency of the radio (see page 32).

RDS doesn’t work.

• The FM station you are tuned to doesn’t support RDS.

• Install an outdoor FM antenna (see page 18).

• Change the position or direction of your outdoor FM antenna (see page 18).

• Move the FM antenna as far away as possible from fluorescent lights (see page 32).

External Components

Can’t record to components connected to LINE 2 or LINE3.

• The CD/HDD receiver does not output signals from LINE 2 IN from LINE 2 OUT. In the same way, signals from

LINE 3 IN are not output from LINE 3 OUT. This protects the CD/HDD receiver from malfunction or failure due to

the loop between input and output.

• If Audyssey EQ™ is active, you cannot perform recording to an external component. Deactivate Audyssey EQ™

(see page 26).

Interactive control with other Onkyo u-capable components is not working.

• Make sure the u cables and analog audio cables are connected correctly (see page 19). Connecting only an u

cable won’t work.

• Make sure the Input Display matches the type of device that you’ve connected to the CD/HDD receiver (see page 45).

No sound is heard from your turntable.

• Make sure the turntable has a built-in phono equalizer.

• If the turntable doesn’t have a phono equalizer built-in, you must provide one.

Record player cannot play.

• When a record player of MC cartridge type is used, a boosting transformer or head amplifier is required.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting—Continued

Timers

Timer playback or recording doesn’t work.

• Make sure the clock has been set correctly (see page 62).

• The timer may overlap with another timer. If you program several timers, make sure they don’t overlap (see page 64).

• The timer will not work when electrical service interruption occurs or the power cord is pulled out during the timer

is set.

• Shock or vibration may prevent the timer from operating normally. Use it in a steady location.

• Timed operation will fail if the CD/HDD receiver is on at the specified On time, so make sure it’s set to Standby

(see page 64).

Internet

Can’t connect to the Internet.

• Confirm the network setting. If you still cannot connect to the Internet after that, contact your internet service provider

(see page 68).

• Make sure the power of the broadband router is on.

• Try the DHCP settings manually (see page 69).

• Try setting the proxy server manually (see page 69).

• Set the broadband router again correctly. For settings, see the instruction manual of your broadband router or the

materials provided by your internet service provider.

• Connect the LAN cable correctly (see page 21).

• Make sure you do not connect directly to the modem without any router function.

• If your contract allows only one terminal that can be connected to the Internet at a time, you cannot connect a terminal

in addition to an existing terminal. Consult your telephone carriers or Internet service providers on your contract.

Remote Controller

The remote controller doesn’t work properly.

• Make sure the batteries have been installed with the correct polarity (+/–) (see page 6).

• Replace both batteries with new ones. (Do not mix different types of batteries or new and old batteries.)

• The remote controller is too far away from the CD/HDD receiver, or there’s an obstacle between them (see page 6).

• The CD/HDD receiver’s remote control sensor is being subjected to bright light (inverter-type fluorescent light or

sunlight).

• The CD/HDD receiver is located behind the glass doors of a audio rack or cabinet.

USB Mass Storage Device Playback

Can’t access the music files on a USB mass storage device.

• Make sure that the USB indicator light is on. If the light is not on, make sure that it is connected correctly and that

the USB mass storage device is one that is supported (see page 41).

• The CD/HDD receiver supports USB mass storage devices that support the USB Mass Storage Class. However,

playback may not be possible with some USB mass storage devices even if they conform to the USB Mass Storage

Class.

• Check that the file format is FAT16 or FAT32.

• USB mass storage devices with an internal USB hub are not supported.

Can’t play music files.

• MP3 files without a “.mp3” or “.MP3” filename extension are not recognized.

• AAC files without a “.m4a” or “.M4A” filename extension are not recognized.

• WAVE files without a “.wav” or “.WAV” filename extension are not recognized.

Can’t play WMA files.

• WMA files without a “.wma” or “.WMA” filename extension are not recognized.

• The WMA file’s copyright option is on. Don’t use the copyright option.

When connected to the USB port, a USB device does not operate. (The message "Error19" appears.)

• First disconnect the USB device and turn the CD/HDD receiver off. When the AC power adapter is attached to the

USB device, connect the AC power adapter to the domestic power supply and connect the USB device to the CD/

HDD receiver again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting—Continued

Others

Track number or playlist number is not displayed correctly.

• The number of tracks or the playlists is 1,000 or more, “- - -” is displayed.

Not operate normally.

• If the CD/HDD receiver is affected by static electricity or the like, it may operate abnormally. At this time, turn off

the power, wait for one minute, and then turn on the power again. If it still does not operate, reset the CD/HDD

receiver.

• When any warning message appears on the screen, follow the message.

When five-digit alphanumeric characters are displayed on the screen:

• The CD/HDD receiver has a self-diagnosis function to prevent a malfunction occurring, and displays five-digit alpha-

numeric characters on the screen when this function is on. In this case, please notify the call center of the characters.

Precautions on RI dock connection

• When changing the Input Selector from DOCK (RI dock) to another, be sure to stop the iPod.

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s

malfunction. Before you record important data, make sure that the material will be recorded correctly.

Disposal and transporting the CD/HDD receiver

Delete all the tracks or data in the hard disk drive before you disposed of the CD/HDD receiver or transport it. When

you have set the network configuration, change the parameters beforehand. Please note that Onkyo will not be respon-

sible for all possible damages and passive damages if the information should be tampered, leaked, changed, or disap-

peared.

The CD/HDD receiver contains a microcomputer for signal processing and control functions. In very rare situations,

severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event

that this should happen, unplug the power cord, wait at least 5 seconds, and then plug it again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

General

Power Supply:

AC 230 V, 50 Hz

76 W

0.6 W

Power Consumption:

Stand-by Power Consumption:

Dimensions (W × H × D):

Weight:

295 × 128 × 313 mm

7.6 kg (16.8 lbs.)

Audio Inputs

Analog Inputs:

Digital Input:

3 (LINE1, DOCK/CDR IN, MD/TAPE IN)

1 (Optical)

Audio Outputs

Analog Outputs:

Subwoofer Pre Output:

Speaker Outputs:

Phones:

2 (DOCK/CDR OUT, MD/TAPE OUT)

ETHERNET port

ETHERNET Interface:

10Base-T

USB port

Plug:

USB type A

Version:

Driver:

Hi-speed USB

USB Mass Storage Class

Amplifier Section

Power Output:

2ch × 20 W (4 Ω, 1 kHz, 2ch driven, IEC)

0.4% (1 kHz , 1 W)

25 (8 Ω)

THD (Total Harmonic Distortion):

Damping Factor:

Input Sensitivity and Impedance:

Output Level and Impedance:

Frequency Response:

150 mV/50 kΩ (LINE1, DOCK/CDR IN, MD/TAPE IN)

150 mV/2.2 kΩ (DOCK/CDR OUT, MD/TAPE OUT)

10 Hz–100 kHz/ 3 dB (LINE1, DOCK/CDR, MD/TAPE)

Tone Control:

6 dB, 80 Hz (BASS)

8 dB, 10 kHz (TREBLE)

+7 dB, 80 Hz (S.BASS)

Signal to Noise Ratio:

Speaker Impedance:

100 dB (LINE1, DOCK/CDR, MD/TAPE, IHF-A)

4 Ω–16 Ω

Tuner Section

Tuning Frequency Range:

87.50 MHz-108.0 MHz

Tuning Frequency Range:

522 kHz–1611 kHz

Preset Channel

Number of preset stations:

40 stations in total, including FM and AM

Frequency Response:

10 Hz–20 kHz

Audio Dynamic Range:

95 dB

THD (Total Harmonic Distortion):

Wow and Flutter:

Audio Output/Impedance (Analog):

0.007%

Below threshold of measurability

1.3 V (rms)/2.2 kΩ

Specifications and features are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

Trademark and Other Proprietary Notices

* This product is manufactured under license from

Dolby Laboratories.

* Microsoft and Windows are registered trademarks or

trademarks of the Microsoft Corporation in the United

States and other countries.

* The jPlayer MPEG Layer-3 audio coding technology

is licensed from Fraunhofer IIS and Thomson Multi-

media.

use of the Gracenote Data, the Gracenote Software, and

Gracenote Servers. Gracenote reserves all rights in

Gracenote Data, the Gracenote Software, and the

Gracenote Servers, including all ownership rights.

Under no circumstances will Gracenote become liable

for any payment to you for any information that you pro-

vide. You agree that Gracenote, Inc. may enforce its

rights under this Agreement against you directly in its

own name.

The Gracenote service uses a unique identifier to track

queries for statistical purposes. The purpose of a ran-

domly assigned numeric identifier is to allow the

Gracenote service to count queries without knowing

anything about who you are. For more information, see

the web page for the Gracenote Privacy Policy for the

Gracenote service.

The Gracenote Software and each item of Gracenote

Data are licensed to you “AS IS.” Gracenote makes no

representations or warranties, express or implied,

regarding the accuracy of any Gracenote Data from in

the Gracenote Servers. Gracenote reserves the right to

delete data from the Gracenote Servers or to change data

categories for any cause that Gracenote deems sufficient.

No warranty is made that the Gracenote Software or

Gracenote Servers are error-free or that functioning of

Gracenote Software or Gracenote Servers will be unin-

terrupted. Gracenote is not obligated to provide you with

new enhanced or additional data types or categories that

Gracenote may provide in the future and is free to dis-

continue its services at any time.

About Gracenote

Music recognition technology and related data are pro-

vided by Gracenote . Gracenote is the industry standard

in music recognition technology and related content

delivery.

For more information visit www.gracenote.com.

CD and music-related data from Gracenote, Inc., copy-

vice may practice one or more of the following U.S. Pat-

ents: #5,987,525; #6,061,680; #6,154,773, #6,161,132,

#6,230,192, #6,230,207, #6,240,459, #6,330,593, and

other patents issued or pending. Services supplied and/or

device manufactured under license for following Open

Globe, Inc. United States Patent 6,304,523.

Gracenote and CDDB are registered trademarks of

Gracenote. The Gracenote logo and logotype and the

“Powered by Gracenote” logo are trademarks of

Gracenote.

GRACENOTE DISCLAIMS ALL WARRANTIES

EXPRESS OR IMPLIED, INCLUDING, BUT NOT

LIMITED TO, IMPLIED WARRANTIES OF MER-

CHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, TITLE, AND NON-INFRINGEMENT.

GRACENOTE DOES NOT WARRANT THE

RESULTS THAT WILL BE OBTAINED BY YOUR

USE OF THE GRACENOTE SOFTWARE OR ANY

GRACENOTE SERVER. IN NO CASE WILL

GRACENOTE BE LIABLE FOR ANY CONSEQUEN-

TIAL OR INCIDENTAL DAMAGES OR FOR ANY

LOST PROFITS OR LOST REVENUES.

Gracenote End User License Agreement

This application or device contains software from

Gracenote, Inc. of Emeryville, California (“Gracenote”).

The software from Gracenote (the “Gracenote Soft-

ware”) enables this application to perform disc and/or

file identification and obtain music-related information,

including name, artist, track, and title information

(“Gracenote Data”) from online servers or embedded

databases (collectively, “Gracenote Servers”) and to per-

form other functions. You may use Gracenote Data only

by means of the intended End-User functions of this

application or device.

You agree that you will use Gracenote Data, the

Gracenote Software, and Gracenote Servers for your

own personal non-commercial use only. You agree not to

assign, copy, transfer or transmit the Gracenote Software

or any Gracenote Data to any third party. YOU AGREE

NOT TO USE OR EXPLOIT GRACENOTE DATA,

THE GRACENOTE SOFTWARE, OR GRACENOTE

SERVERS, EXCEPT AS EXPRESSLY PERMITTED

HEREIN.

You agree that your non-exclusive license to use the

Gracenote Data, the Gracenote Software, and Gracenote

Servers will terminate if you violate these restrictions. If

your license terminates, you agree to cease any and all

Download from Www.Somanuals.com. All Manuals Search And Download.

Memo

Download from Www.Somanuals.com. All Manuals Search And Download.

Memo

Download from Www.Somanuals.com. All Manuals Search And Download.

Memo

Download from Www.Somanuals.com. All Manuals Search And Download.

Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8163

ONKYO U.S.A. CORPORATION

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/

ONKYO EUROPE ELECTRONICS GmbH

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/

ONKYO EUROPE UK Office

Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ

UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452

HOMEPAGE

http://www.onkyo.com/

ONKYO CHINA LIMITED

Unit 1&12, 9/F, Ever Gain PlazaTower 1, 88, Container Port Road, Kwai Chung,

N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039

http://www.ch.onkyo.com/

Y0809-1

SN 29344841

* 2 9 3 4 4 8 4 1 *

Download from Www.Somanuals.com. All Manuals Search And Download.

Miele Freezer F1471SF User Manual
Miele Oven H387 1BPKAT User Manual
Multi Tech Systems Network Router MT128SMI User Manual
National Computer Hardware CP3BT26 User Manual
NEC Flat Panel Television PX 42XR4A User Manual
NETGEAR Cordless Telephone SPH200D User Manual
Olympus Microcassette Recorder DS 150 User Manual
Omron Heart Rate Monitor HCG 801 User Manual
Panasonic Conference Phone KXTS840B User Manual
Panasonic Network Card 2SC2406 User Manual