FEATURE - FUNCTION
The Light (LED) flashes red to show
URC 5800
Cinema 5+
that the remote is working and is sending a signal.
The SETUP key is used to program your
Cinema 5.
The POWER key controls power ON and OFF the
same as the POWER key on your original remote.
Please note that most CD Players do not have an
ON/OFF function on the original remote control. If
this is the case with your CD Player, then POWER
will have no effect on your CD Player.
User Guide
OVERVIEW
®
™
Thank you for purchasing the One For All Cinema 5 uni-
versal remote control with learning. Along with being a com-
plete Home Theater universal remote, the Cinema 5’s
sophisticated technology will allow you to finally consolidate
the clutter of all of the original remotes in your home enter-
tainment system. Through patented learning technology, you
can teach your Cinema 5 the unique features of your original
remotes and create the complete universal remote control –
only from One For All.
The TV, VCR, CBL/SAT, DVD/LD or RCVR keys
are used to select the home entertainment compo-
nent you want to control. If your component does
not respond when you press a key on the remote
control, press the appropriate device key (TV,
VCR, CBL/SAT, DVD/LD or RCVR) first to tell the
remote control which component you would like
the remote to operate.
Before you can use your new remote control, you will need
to program it to operate the specific home entertainment
components you wish to control. Follow the instructions
detailed in this manual to set up your Cinema 5 and enjoy
your new remote control.
The VOL (Volume Up), VOL (Volume Down)
and MUTE keys control the volume the same as
the Volume Up and Down and Mute keys on your
original remote.
FEATURES AND FUNCTIONS
The illustration below and the chart on the next three pages
describe the features and functions of the Cinema 5 univer-
sal remote control. Use the drawing to locate each feature of
the remote, then refer to the chart for a description of what
function each feature performs.
The CH (Channel Up) and CH (Channel
Down) keys change channels the same as the
Channel Up and Down keys on your original
remote. The CH
/
keys also control the fol-
lowing functions in other modes: DVD/LD
mode = Skip Forward/ Skip Reverse, RCVR, AUX
and CD mode = Preset Up/Preset Down.
CBL/SAT
The Digit keys (0-9) control direct channel access
the same as the Digit keys on your original
remote. The Digit keys (0-9) may also control the
following functions in other modes: RCVR and
AUX modes = Input Selections.
RCVR
DVD/LD
The ENTER key operates the same as the Enter
key on your original remote. If your original remote
control required you to use an Enter key to change
channels, use the ENTER key on the Cinema 5
after entering your channel number. The ENTER
key may also control the following functions in
other modes: RCVR and AUX modes = TAPE
MON.
The PREV CH (Previous Channel) key operates
the same as the Last Channel or Recall key on
your original remote. The PREV CH key may also
control the following functions in other modes:
DVD/LD, RCVR and CD mode = Random.
The CH ꢀꢀ/ ꢀ, VOL ꢀꢀ/ ꢀ, MUTE, PREV CH
and Digit (0-9) keys are made of a phosphores-
cent material that glows-in-the-dark. Expose the
keys to bright light to activate the glow-in-the-dark
feature. The length of time the keys remain illumi-
nated will be determined by the length of time the
remote is exposed to bright light.
SET
Download from Www.Somanuals.com. All Manuals Search And Download.
Locate the brand name of your TV in the “Setup Codes For
TVs” section (starting on the next page), and write it in the
space below.
Electroband
Emerson
0000, 0185
0463, 0236, 0180, 0019, 0154, 0177,
0178, 0179, 0185, 0282, 0039, 0624
Envision
Fisher
Fujitsu
Funai
Futuretech
GE
0030
0154, 0159
0179
0171, 0179, 0180
TV Brand:__________________________________________
The brands are listed in alphabetical order with the most
popular codes listed first. You will use one of these codes to
program your Cinema 5 to operate your TV as follows:
0180
0047, 0051, 0451, 0021, 0178, 0282,
0135, 1147, 1347
0019, 0030, 0017
0019, 0030, 0178, 0039
0053, 0056
0179, 0180
0178
0180
0145, 0151, 0056
0054
0054
0000
0053
0180
0019, 0030
0024
1.
2.
Turn on your TV.
Gibralter
Goldstar
Gradiente
Grunpy
Hallmark
Harvard
Hitachi
Infinity
JBL
JCB
JVC
KEC
Kenwood
Kloss
On the Cinema 5, press TV and release. Press
and hold SETUP until the red light blinks twice,
then release SETUP.
3.
4.
Enter the first four-digit TV code listed for your
brand. If performed correctly, the red light will blink
twice when you enter the final digit.
Aim the Cinema 5 at your TV and press POWER.
The TV should turn off. If it does not respond,
repeat steps 2-4, trying each code listed for your
brand until you find the one that operates your TV.
NOTE: If you have tried all the codes listed for
your brand and your TV does not respond, try
using ”SEARCHING FOR YOUR CODE”.
KTV
LG
Logik
0030, 0180, 0185, 0032
0056
0016
Luxman
LXI
Magnasonic
0056
5.
Your Cinema 5 is now programmed to operate
your TV. Write your TV code in the boxes to the left
for future reference.
0047, 0054, 0154, 0156, 0178
0179, 0030, 0092, 0093, 0019, 0003,
0054, 0156
Magnavox
Majestic
Marantz
Matsushita
Megatron
MEI
0054, 0096, 0187, 0030, 0179, 0171
0016
0054, 0030
0250
0145, 0178
0185
Remember, if you want to use your Cinema 5 to operate
Memorex
MGA
Midland
Minutz
0056, 0150, 0154, 0016, 0178
0150, 0019, 0030, 0178
0017, 0047, 0051, 0135, 0039
0021
your TV, press the TV key first.
Setup Codes For TVs
Mitsubishi
Motorola
MTC
Multitech
NAD
NEC
Nikko
NTC
Onwa
Optimus
Optonica
Orion
Panasonic
Penney
0150, 0093, 0019, 0178
0093
0060, 0019, 0030, 0056, 0185
0180
0156, 0166, 0178
0019, 0030, 0056
0030, 0092, 0178
0092
0180
0250, 0154, 0166
0093, 0165
0236, 0436
0250, 0051
0047, 0156, 0051, 0030, 0019, 0021,
0060, 0135, 0178, 0039, 1347
0054, 0145, 0096, 0019, 0030
0054
0019, 0030, 0039
0166
0092, 0019, 0039
0051
0047
Admiral
Aiko
Akai
Alaron
Ambassador
Ampro
0093, 0179, 0180, 0016, 0047
0092
0030
0179
0177
0751
0180
0019, 0185, 0003
0451, 0092, 0180, 0003
0180
0017, 0030, 0179
0019
0154, 0016
0180
0019
0056, 0030
0030
0054
0000
0451, 0092
0060, 0092, 0030, 0056, 0039
0185
0056
0180, 0185
0180
0180, 0039
0030, 0060, 0154, 0039, 0466, 1147, 1347
0180
0451, 0092, 0019, 0039, 0624
0019
0145
0017, 0019
0720, 0774
Anam
AOC
Audiovox
Baysonic
Beaumark
Belcor
Bell & Howell
Bradford
Brockwood
Candle
Carnivale
Carver
Celebrity
Cineral
Citizen
Clairtone
Concerto
Contec
Craig
Crown
Curtis Mathes
CXC
Daewoo
Daytron
Denon
Dumont
Dwin
Philco
Philips
Pilot
Pioneer
Portland
Prism
Proscan
Proton
Pulsar
0178, 0466
0017, 0019
Quasar
RadioShack
0250, 0051, 0165
0047, 0056, 0154, 0019, 0030, 0165,
0178, 0180, 0039
0047, 0019, 0090, 0135, 1047, 1147,
1247, 1347
0056, 0154, 0019, 0030, 0165, 0178,
0180, 0039
0185
RCA
Realistic
Rhapsody
Runco
Sampo
0017, 0030, 0603
0030, 0039
Download from Www.Somanuals.com. All Manuals Search And Download.
Samsung
Samsux
Sansei
Sanyo
0060, 0019, 0030, 0056, 0178, 0039
0039
0451
0154, 0159
NOTE: If you have tried all the codes listed for
your brand and your VCR does not respond, try
using “SEARCHING FOR YOUR CODE”.
Scimitsu
Scotch
Scott
0019
0178
5.
Your Cinema 5 is now programmed to operate
your VCR. Write your VCR code in the boxes to
the left for future reference.
0236, 0019, 0178, 0179, 0180
Sears
0047, 0054, 0056, 0154, 0156, 0171,
0178, 0159, 0179
Semivox
Semp
0180
0156
Sharp
0093, 0165, 0039
Remember, if you want to use your Cinema 5 to operate
Shogun
Signature
Simpson
Sony
Soundesign
Squareview
SSS
0019
0016
0187
0000
0178, 0179, 0180
0171
0019, 0180
0180
0000
0054, 0096, 0030
0171
0093
0250, 0051
0179
0051, 0056
0054, 0056, 0060, 0092, 0150, 0016,
your VCR, press the VCR key first.
Setup Codes For VCRs
Admiral
Adventura
Aiko
0048, 0121, 0184, 0039, 0060, 0202
0000
0278
Aiwa
Akai
0037, 0000
0041
Starlite
American High 0035
Supreme
Sylvania
Symphonic
Tandy
Technics
Technol Ace
Techwood
Teknika
Asha
0240
Audiovox
Beaumark
Bell & Howell
Broksonic
Calix
0037
0240
0104
0184, 0209, 0479, 0002, 0121
0037
Canon
0035
Carver
0081
0019, 0179, 0180, 0039
0056
0056, 0177, 0178
0156, 0060, 0154
0185
CCE
0072, 0278
Telefunken
TMK
Toshiba
Tosonic
Totevision
Vector Research 0030
Victor
Vidikron
Vidtech
Viking
Cineral
0278
Citizen
0037, 0278
Colt
0072
Craig
0072, 0240, 0037, 0047, 0271
0039
Curtis Mathes
Cybernex
Daewoo
Denon
0035, 0041, 0060, 0202
0240
0278, 0045
0042
0053
0054
0019, 0178
0046
0016, 0019, 0030, 0054, 0056, 0096,
0165, 0178, 0179, 0021
Dynatech
Electrohome
Electrophonic
Emerex
Emerson
0000
0037
0037
0032
Wards
White
0209, 0184, 0479, 0278, 0000, 0002,
Westinghouse 0451, 0463, 0236, 0180, 0624
Yamaha
Zenith
0036, 0037, 0043, 0068, 0121, 0184, 0212
0019, 0030
0017, 0092, 0016
Fisher
Fuji
Funai
0104, 0047, 0066
0033, 0035
0000
Programming the Cinema 5 to operate your VCR:
Garrard
GE
Goldstar
Go-Video
Gradiente
0000
Locate the brand name of your VCR in the “Setup Codes For
VCRs” section (starting below), and write it in the space
below.
0060, 0035, 0048, 0240
0037, 0038
0432, 0526
0000
VCR Brand: ________________________________________
Harley Davidson 0000
Harman/Kardon 0038
The brands are listed in alphabetical order with the most pop-
ular codes listed first.You will use one of these codes to pro-
gram your Cinema 5 to operate your VCR as folllows:
Harwood
Headquarter
HI-Q
0072, 0068, 0072
0046
0047
Hitachi
Jensen
JVC
KEC
Kenwood
KLH
0041, 0000, 0042
0041
0041, 0067
0037, 0278
0038, 0041, 0067
0072
1.
2.
Turn on your VCR and play a tape.
On the Cinema 5, press VCR and release. Press
and hold SETUP until the red light blinks twice, then
release SETUP.
Kodak
Lloyd’s
Logik
0035, 0037
0000, 0208
0072
0037
0278, 0179, 0171, 0020, 0037, 0072, 0240
0035, 0081, 0000, 0039, 0110, 0149
0240
0035, 0081
3.
4.
Enter the first four-digit VCR code listed for your
brand. If you perform this procedure correctly, the
red light will blink twice when entering the final
digit.
LXI
Magnasonic
Magnavox
Magnin
Marantz
Marta
Matsushita
MEI
Memorex
Aim the Cinema 5 at your VCR and press
POWER.Your VCR should turn off. If your original
VCR remote control did not have a POWER key,
press STOP. Your VCR should stop. If your VCR
does not respond, repeat steps 2-4, trying each
code listed for your brand until you find the one that
operates your VCR.
or
0037
0162, 0035, 0454
0035
0162, 0240, 0035, 0037, 0104, 0000,
Download from Www.Somanuals.com. All Manuals Search And Download.
0039, 0046, 0047, 0048, 1037, 1062,
1162, 1262
Programming the Cinema 5 to operate your TV/VCR
Combo:
MGA
0043, 0240
Locate the brand name of your TV/ VCR Combo in the
“Setup Codes For TV/ VCR Combos” section (starting on the
next page), and write it in the space below.
MGN Technology 0240
Minolta
Mitsubishi
Motorola
MTC
0042
0043, 0048, 0067
0035, 0048
0240, 0000
TV/VCR Combo Brand: ____________________________
Multitech
NEC
Nikko
Noblex
Olympus
Optimus
0000, 0072
0038, 0041, 0067, 0104
0037
0240
The brands are listed in alphabetical order with the most
popular codes listed first. You will use one of these codes to
program your Cinema 5 to operate your TV/VCR Combo as
follows:
0035
0162, 0048, 0037, 0104, 0454, 1037,
1062, 1162, 1262
0209, 0184, 0479, 0002
0162, 0035, 0077, 0225, 0454, 1062,
1.
2.
Turn on your TV/VCR Combo.
Orion
Panasonic
Press VCR and release. Press and hold SETUP
until the Cinema 5’s red light blinks twice, then
release SETUP.
1162, 1262
Penney
Pentax
Philco
Philips
Pilot
Pioneer
Proscan
Protec
Pulsar
Quarter
Quartz
Quasar
RadioShack
Radix
0035, 0037, 0038, 0042, 0240
0042
0035, 0209, 0479
0035, 0081, 0110
0037
0067, 0162
0060, 0202
0072
3.
4.
Enter the first four-digit TV/VCR code listed for
your brand in the “Setup Codes For TV/VCR
Combos” section. If you perform this procedure
correctly, the red light will blink twice when you
enter the final digit of your code.
Aim the Cinema 5 at your TV/VCR Combo and
press POWER. The unit should turn off. If it does
not respond, Repeat steps 2-4, trying each code
listed for your brand until you find the one that oper-
ates your TV/VCR Combo.
0039
0046
0046
0162, 0035, 0077, 0454, 1062, 1162, 1262
0000, 0037, 1037, 1062, 1162, 1262
0037
0037
0060, 0240, 0042, 0035, 0048, 0077, 0149
0000, 0035, 0037, 0046, 0047, 0048,
NOTE: If you have tried all the codes listed for
your brand and your TV/VCR Combo does not
respond, try using “SEARCHING FOR YOUR
CODE”.
Randex
RCA
Realistic
0066, 0104
Runco
Samsung
Sanky
Sansui
Sanyo
Scott
0039
0240, 0045
0048, 0039
0000, 0041, 0067, 0271, 0479
0104, 0046, 0047, 0054, 0240
0043, 0045, 0121, 0184, 0210
5.
Your Cinema 5 is now programmed to operate
your TV/VCR Combo. Write your TV/VCR Combo
code in the boxes to the left for future reference.
Sears
0000, 0035, 0037, 0042, 0046, 0047,
0066, 0104
Remember, to use your Cinema 5 to operate your TV/VCR
Semp
0045
Combo, press the VCR key first.
Sharp
0048
0072
0240
0072
Setup Codes For TV/VCR Combos
Shintom
Shogun
Singer
Sony
STS
Sylvania
Symphonic
Tatung
TEAC
Technics
Teknika
Thomas
TMK
American High 0035*
Brocksonic
Colt
0002, 0294, 0479
0072
0032, 0033, 0000, 0035
0042
0035, 0081, 0043, 0000, 0110
0000
0041
0000, 0041
0162, 0035
0000, 0035, 0037
0000
0240, 0036, 0208
0043, 0045, 0066, 0210
0037, 0240
Curtis Mathes
Daewoo
Emerson
Funai
0035*
0278*
0002, 0294, 0479
0000
GE
Hitachi
HQ
0035*, 0060*, 0048*, 0240
0035*, 0000
0000
Lloyds
0000
Magnavox
Magnin
Memorex
MGA
0000, 0035*, 0081*
0240
0037, 0162*
0240
Toshiba
Totevision
Unitech
0240
Mitsubishi
Orion
Panasonic
Penney’s
Quasar
RCA
0048*
Vector Research 0038
Vector 0045
Video Concepts 0040, 0045
0002, 0294, 0479
0035*, 0162*
0035*, 0240, 0162*
0035*, 0162*
0035*, 0060*, 0048*
0000, 0479
0240
Videosonic
Wards
0240
0000, 0035, 0042, 0047, 0048, 0060,
0072, 0081, 0149, 0240
Sansui
Sanyo
White
Westinghouse 0278, 0479, 0209, 0184
Sears
Sony
Symphonic
Zenith
0000, 0037
0032*
0000
XR-1000
Yamaha
Zenith
0000, 0035, 0072
0038
0039, 0000, 0033
0000
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: If your TV/VCR works with one of the above codes
highlighted with an asterisk (*), you may need to program a
separate TV code to control the volume. Check the list of
codes below and follow the instructions in the “Programming
the Cinema 5 to Operate Your TV” section to program the
supplied TV code.
Setup Codes for Cable Converters
ABC
0003, 0008, 0014, 0007, 0001, 0011,
0013, 0017
0153, 0315
0022, 0207
0797, 0153, 0022, 0207
0056
Allegro
Gantronix
Archer
Belcor
TV/VCRs working on VCR code 0032 may require
TV code 0000 for volume control.
TV/VCRs working on VCR code 0035 may require
TV code 0051 for volume control.
TV/VCRs working on VCR code 0048 may require
TV code 0093 for volume control.
TV/VCRs working on VCR code 0060 may require
TV code 0047 for volume control.
TV/VCRs working on VCR code 0081 may require
TV code 0054 for volume control.
TV/VCRs working on VCR code 0162 may require
TV code 0250 for volume control.
TV/VCRs working on VCR code 0278 may require
TV code 0451 for volume control.
Cable Star
Cabletenna
Cableview
Century
Citizen
Colour Voice
Comtronics
Contec
0056
0022
0022
0153
0153, 0315
0031
0040
0019
Digi
0637
Eastern
Emerson
Everquest
Focus
0002
0797
0015, 0040
0400
Garrard
0153
GC Electronics 0056, 0207
Programming the Cinema 5 to operate your Cable
Converter or Satellite Receiver:
Gemini
0015
General
Locate the brand name of your Cable Converter or Satellite
Receiver in the “Setup Codes for Cable Converters” or “Setup
Codes for Satellite Receivers” section (starting on the next
page), and write it in either space below.
Instrument
0476, 0003, 0014, 0011, 0276, 0810
Goldstar
Goodmind
Hamlin
0144, 0040
0797
0259, 0009, 0020, 0034
Hitachi
Hytex
Jasco
Jerrold
0011
0007
Cable Converter Brand:____________________________________________________________________________________
________________________________________________
0153, 0315, 0015
0476, 0003, 0014, 0011, 0012, 0015, 0810
or
Linsay
0440
0027, 0014
0000
0063, 0156
0618
0063, 0156
0007, 0019
0021
0021, 0107, 0000
0637
0000
0153, 0027, 0031
0144, 0023, 0533
Satellite Receiver Brand:______________________________
________________________________________________
Magnavox
Memorex
Movie Time
Novaplex
NSC
The brands are listed in alphabetical order with the most pop-
ular codes listed first.You will use one of these codes to pro-
gram your Cinema 5 to operate your Cable Converter or
Satellite Receiver as follows:
Oak
Optimus
Panasonic
Panther
Paragon
Philips
Pioneer
Popular
Mechanics
Prelude
Pulsar
RadioShack
RCA
Realistic
Recoton
Regal
1.
Turn on your Cable Converter or Satellite
Receiver.
2.
Press CBL/SAT and release. Press and hold SETUP
until the Cinema 5’s red light blinks twice, then
release SETUP.
0400
0770
0000
3.
4.
Enter the first four-digit Cable Converter or
Satellite Receiver code listed. If you perform this
procedure correctly, the red light will blink twice
when you enter the final digit of your code.
0015, 0315, 0797, 0833
0021
0207
0400
0259, 0020
0002
0011
0000
0144, 0040
Aim the Cinema 5 at your Cable Converter or
Satellite Receiver and press POWER.Your Cable
Converter or Satellite Receiver should turn off. If it
does not respond, repeat steps 2-4, trying each
code listed for your brand until you find the one
that operates your Cable Converter or Satellite
Receiver.
Regency
Rembrandt
Runco
Samsung
Scientific Atlanta 0477, 0008, 0017
Seam
Signal
0510
0015, 0040
0011
0040
0021
0003, 0015
0015, 0040, 0797
0015
0001
0258
NOTE: If you have tried all the codes listed for
your brand and your Cable Converter or Sateliite
Receiver does not respond, try using “SEARCH-
ING FOR YOUR CODE”.
Signature
SL Marx
Sprucer
Starcom
Stargate
Starquest
Sylvania
Tandy
5.
Your Cinema 5 is now programmed to operate
your Cable Converter or Satellite Receiver. Write
your Cable Converter or Satellite Receiver code in
the boxes to the left for future reference.
Teleview
Texscan
TFC
Timeless
Tocom
0040
0001
0310
0418
Remember, if you want to use your Cinema 5 to operate
your Cable Converter or Satellite Receiver, press the
CBL/SAT key first.
0012, 0013
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba
Tusa
TV86
0000
0015
0063
0153, 0022, 0207
5.
Your Cinema 5 is now programmed to operate your
DVD or Laser Disc Player. Write your DVD or Laser
Disc Player code in the boxes to the left for future ref-
erence.
Unika
United Artists
United Cable
Universal
Videoway
Viewstar
Zenith
0007
0003
0153, 0022, 0056, 0191, 0207
0250
0063, 0027, 0258
0525, 0000, 0015, 0207, 0008
0400
Remember, to use Cinema 5 to operate your DVD or Laser
Disc Player, press the DVD/LD key first.
Setup Codes for DVD Players
Zentek
JVC
0558
Setup Codes for Satellites
Kenwood
Magnavox
Mitsubishi
Onkyo
0534
0503
0521
0503
AlphaStar DBS 0772
Chaparral
Echostar DBS
ExpressVu DBS 0775
General
Instrument
Hitachi DBS
HTS DBS
Hughes Network
Systems DBS 0749
Jerrold Primestar 0627
0216
0775
Panasonic
Philips
Pioneer
Proscan
RCA
0490
0539, 0503
0525, 0571
0522
0361, 0627, 0869
0819
0775
0522
Samsung
Sony
0573
0533
Technics
Toshiba
Yamaha
Zenith
0490
0503
0490, 0545
0503
Jerrold
JVC
0361
0775
Magnavox DBS 0722, 0724
Memorex DBS 0724
Panasonic DBS 0701
Philips DBS
Primestar
Proscan
RCA DSS
Sony DBS
Star Choice DBS 0869
Setup Codes for Laser Disc Players
0722, 0724
0361, 0627
0566
0566, 0143, 0855
0639
Denon
Mitsubishi
NAD
0059
0059
0059
Pioneer
Sony
0059
0193, 0201
Programming the Cinema 5 to operate your Receiver/Tuner:
STS
0210
0790
0724, 0722
0856
Locate the brand name of your Receiver/Tuner in the “Setup
Codes For Receiver/Tuners” section (starting below), and
write it in below.
Toshiba DBS
Uniden DBS
Zenith
Receiver/Tuner Brand:________________________________
Programming the Cinema 5 to operate your DVD or
Laser Disc Player:
The brands are listed in alphabetical order with the most
popular codes listed first. You will use one of these codes to
program your Cinema 5 to operate your Receiver/Tuner as
follows:
Locate the brand name of your DVD or Laser Disc Player in
the DVD or Laser Disc Player setup codes (starting below),
and write it in the space below.
1.
2.
Turn on your Receiver/Tuner.
DVD/LD Player Brand:________________________________
Press RCVR and release. Press and hold SETUP
until the Cinema 5’s red light blinks twice, then
release SETUP.
The brands are listed in alphabetical order with the most pop-
ular codes listed first.You will use one of these codes to pro-
gram your Cinema 5 to operate your DVD or Laser Disc
Player as follows:
3.
4.
Enter the first four-digit Receiver/Tuner code listed
for your brand in the “Setup Codes For
Receivers/Tuners” section. If performed correctly,
the red light will blink twice when you enter the
final digit.
1.
Turn on your DVD or Laser Disc Player and insert
a disc.
2.
Press DVD/LD and release. Press and hold
SETUP until the Cinema 5’s red light blinks twice,
then release SETUP.
Aim the Cinema 5 at your Receiver/Tuner and press
POWER. The unit should turn off. If it does not
respond, repeat steps 2-4, trying each code listed
for your brand until you find one that works.
3.
4.
Enter the first four-digit DVD or Laser Disc Player
code listed for your brand. If performed correctly,
the red light will blink twice when entering the final
digit.
NOTE: If the unit still does not respond, try using
“SEARCHING FOR YOUR CODE”.
Aim the Cinema 5 at your DVD or LaserDisc
Player and press POWER.Your DVD or Laser Disc
Player should turn off. If it does not respond,
repeat steps 2-4, trying each code listed for your
brand until you find the one that works.
5.
Your Cinema 5 is now programmed to operate
your Receiver/Tuner. Write your Receiver/Tuner
code in the boxes to the left for future reference.
NOTE: If you have tried all the codes listed for your
brand and your DVD or Laser Disc Player does not
respond, try using ‘SEARCHING FOR YOUR
CODE”.
Download from Www.Somanuals.com. All Manuals Search And Download.
Remember, to use your Cinema 5 to operate your
Receiver/Tuner, press the RCVR key first.
4.
5.
Slowly alternate between pressing POWER* and
TV until your TV turns OFF. Make sure that the
Cinema 5 is aimed at your TV during the search.
You may have to press this sequence of buttons
(POWER* then TV) up to 100 times to search the
entire library of codes.
Setup Codes For Receivers/Tuners
ADC
Akai
Aiwa
0531
0076
0121, 0158, 0189, 0405
Bang & Olufsen 0898
When your TV turns OFF, press and release
SETUP to lock in the code for your TV.Your
Cinema 5 is now programmed to operate your TV.
Capetronic
Carver
0531
0008, 0042, 0189, 0360
Casio
0195
Clarinette
Curtis Mathes
Denon
Fisher
Garrard
0195
0039, 0080
0004
0042, 0360
0463
*If you are searching for your VCR, CD, LD or DVD Player
code, you may want to play a tape or disk and use the STOP
key instead of the POWER key to search for your code.
When your VCR stops, press SETUP to lock in your code.
NOTE: To search for the codes of your other components,
repeat Steps 1 through 5, only substitute the appropriate
device key (ie., VCR, DVD/LD, RCVR, CD or CBL/SAT) for
the component you are searching for.
Harman/Kardon 0110, 0891, 0189
JBL
0110
JVC
0074
Kenwood
Linn
0027, 0313, 0314, 0186, 0042
0189
Lloyd’s
LXI
Magnavox
Marantz
MCS
Modulaire
NAD
Nakamichi
Onkyo
Optimus
0195
0181
RETRIEVING THE CODES PROGRAMMED INTO THE
Cinema 5
0189, 0195, 0531, 0391
0039, 0189
0039
0195
0320
0097
0135, 0380
0042, 0080, 0181, 0186, 0531, 0670,
0738, 0801
0039, 0309, 0518
0195
0189
0014*, 0080*, 0150, 0531, 0630, 1023
0039
0054, 0360, 0531, 0530
0181, 0195
0189
0322
0186
0491, 0502
If you have set up the Cinema 5 using the “SEARCHING
FOR YOUR CODE” procedure, you may want to figure out
which four-digit code is operating your equipment. Use this
procedure after you have set up your components to find out
which four-digit code is operating your equipment. For exam-
ple, to find out which code is operating your TV after setting
up your TV using the “SEARCHING FOR YOUR CODE”
procedure:
Panasonic
Penney
Philips
Pioneer
Quasar
RCA
Realistic
Sansui
Scott
1.
Press TV and release. Press and hold SETUP until
the Cinema 5’s red light blinks twice, then release
SETUP.
2.
3.
Press 9 - 9 - 0.
For the first digit of your four-digit code, press 1
and count the number of times the red light (LED)
blinks on the Cinema 5. If the light does not blink
when you press the number 1, the digit is zero.
Sharp
Sherwood
Sony
0158**, 0474
Soundesign
TEAC
Technics
Victor
Wards
Yamaha
Yorx
0670
0463
0039, 0309, 0518
0074
0014, 0042, 0054, 0080, 0158, 0189
0176, 0186
0195
4.
5.
6.
For the second digit, press 2 and count the num-
ber of times the red light (LED) blinks on the
Cinema 5. If the light does not blink when you
press the number 2, the digit is zero.
For the third digit, press 3 and count the number
of times the red light (LED) blinks on the Cinema
5. If the light does not blink when you press the
number 3, the digit is zero.
Zenith
0857
*May use Amplifier code 0013 for power and volume. See
page 21 for amplifier setup and codes.
For the fourth and final digit, press 4 and count the
number of times the red light (LED) blinks on the
Cinema 5. If the light does not blink when you
press the number 4, the digit is zero. Now you
have your four-digit code.
**May use Misc. Audio code 0159 to operate surround and
tuner presets. See page 24 for misc. audio setup and codes.
SEARCHING FOR YOUR CODE
NOTE: To find out the code for your other components,
repeat Steps 1 through 6, only substitute the appropriate
device key (VCR, DVD/LD, RCVR, CD or CBL/SAT) for the
component code you wish to learn.
If your TV, VCR or Cable Converter does not respond to the
Cinema 5 after trying all of the codes listed for your brand, or if
your brand is not listed at all, try searching for your code. For
example, after trying all of the codes for your TV, you still can-
not get the Cinema 5 to operate your TV, then:
LEARNING FUNCTIONS ONTO THE 1L, 2L, 3L AND 4L
KEYS
1.
2.
Turn on your TV.
Press TV and release. Press and hold SETUP until
the Cinema 5’s red light blinks twice, then release
SETUP.
The 1L, 2L, 3L and 4L keys can be used to customize those
functions that are unique to your home entertainment needs.
For example, the Cinema 5 does not offerTracking Up or
Down for a VCR. With the learning feature on the Cinema 5,
you can add these functions and many others learned from
your original remote control.
3.
Press 9 - 9 - 1.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Please have your original remote controls handy before
performing learning on the Cinema 5.
SETTING UP OTHER COMPONENTS
In addition to the components labeled on the device keys
(TV, VCR, DVD/LD, CBL/SAT, etc.), the Cinema 5 can also
operate the following components: Cassette Decks, Infrared
Home Automation, MiniDisc, Video Accessories and Miscel-
laneous Audio Components (Graphic Equalizers and Digital
Music Service Boxes).
1.
2.
3.
Press and hold SETUP until the Cinema 5’s red
light blinks twice, then release SETUP.
Press 9 - 7 - 5. The Cinema 5’s red light will blink
twice.
Press and release the Device key in which you want
to learn a feature (e.g., TV).
The Setup Codes for these components can be accessed
under the following device keys:
NOTE: Steps 4 through 6 need to be completed within 10
seconds. Please read the next three steps before proceed-
ing.
Cassette Decks:
IR Home Automation:
MiniDisc:
Use the VCR Key
Use the CD Key
Use the CD Key
4.
Press and release the L key in which the new fea-
ture is to be learned. The Cinema 5’s red light will
flash rapidly.
Video Accessories:
Use the CBL/SAT Key
(Note : WebTV found under Video Accessories)
Miscellaneous Audio: Use the AUX or RCVR Key
For example, to set up a Cassette Player on the VCR key:
5.
Align your original remote control with the arrow
mark to the left of the LED on your Cinema 5
remote control (see diagram below)
1.
2.
Turn on your Cassette Player and insert a tape.
Press VCR and release. Press and hold SETUP
until the Cinema 5’s red light blinks twice, then
release SETUP.
3.
4.
5.
Enter the first four-digit Cassette Player code listed
for your brand in the “Setup Codes For Audio
Cassettes” section. If you perform this procedure
correctly, the red light will blink twice when you
enter the final digit of your code.
NOTE: This diagram assumes that your original remote’s
LED is in the center. It may also be off center (to the right or
left side) If your Cinerma 7 will not take the command from
your original, try moving the originals alignment left or right
and see if the Cinema 5 accepts the signal from either posi-
tion.
Aim the Cinema 5 at your Cassette Player and
press PL (Play).Your unit should play the tape. If it
does not respond, repeat steps 2-4, trying each
code listed for your brand until you find the one
that works.
6.
On your original remote, press and hold the key
(feature) you want to learn until the red light on the
Cinema 5 blinks twice. (If the red light does not
blink twice, stop and repeat steps 1 through 6.)
Your Cinema 5 is now programmed to operate
your Cassette Player.
NOTE: You can now repeat steps 3 through 6 to learn func-
tions on the other L keys.
Remember, if you want to use your Cinema 5 to operate
your Cassette Player, press the VCR key first.
7.
Press and hold in the SETUP key until the Cinema
5’s red light flashes twice to lock in your new fea-
ture. (If the red light does not blink twice, stop and
repeat steps 1 through 6).
Setup Codes For Audio Cassettes
Aiwa
0029, 0197
Bang & Olufsen 0219
8.
To test the new feature, press and release the
Device key in which the feature was learned fol-
lowed by the L key on which the feature was
learned.
Carver
Denon
0029
0076
Harman/Kardon 0182
JVC
0244
Magnavox
Marantz
Optimus
Philips
Pioneer
Sansui
Sony
Victor
Wards
Yamaha
0029
0029
0027, 0220
0029
0027, 0220
0029
0170, 0243, 0291
0273
0027
Deleting Functions from the L Keys:
1.
Press and hold in the SETUP key until the Cinema
5’s red light flashes twice and then release the
SETUP key.
2.
3.
Enter in 9 - 7 - 6.
Press and release the Device key (e.g., TV) where
0097
the learned feature to be deleted is stored.
Setup Codes For IR Home Automation
4.
Press the L key to be deleted twice. The Cinema
5’s red light will blink twice after the second press
of the L key.
GE
0240
Lutron
One For All
RadioShack
0318, 0597
0167
0240
Security System 0167
Universal X10
X10
0167
0167
RCVR to VCR
SETUP* - 992 - VCR - RCVR - RCVR -
Setup Codes For MiniDisc
SETUP* - VCR code
Denon
JVC
Onkyo
Sharp
Sony
0873
0826, 0681
0868
0861
0490
RCVR to DVD/LD
RCVR to CBL/SAT
CBL/SAT to TV
SETUP* - 992 - DVD/LD - RCVR - RCVR -
SETUP*- DVD/LD Player code
SETUP* - 992 - CBL/SAT - RCVR -
RCVR - SETUP* - Cable/DBS code
SETUP* - 992 - TV - CBL/SAT -
CBL/SAT - SETUP* - TV code
Setup Codes For Video Accessories
Archer 0160
GC Electronics 0160
Jebsee 0160
Magnavox Web-TV 0818
Philips Web TV 0818
RadioShack
TeleCaption
Sony Web-TV
CBL/SAT to VCR
CBL/SAT to DVD/LD
CBL/SAT to RCVR
SETUP* - 992 - VCR - CBL/SAT -
CBL/SAT - SETUP* - VCR code
SETUP* - 992 - DVD/LD - CBL/SAT -
CBL/SAT - SETUP* - DVD or LD code
0160
0171
0850
SETUP* - 992 - RCVR - CBL/SAT -
CBL/SAT - SETUP* - Audio code
*NOTE: Here (*) you must hold SETUP until the Cinema 5’s
red light blinks twice.
Setup Codes For Miscellaneous Audio
Aiwa
0010, 0159, 0404
0052
Fisher
Harman/Kardon 0477
PROGRAMMING THE MACRO KEYS
Jerrold
JVC
Nikko
RCA
0459, 0520
0073
0376
0056
The Cinema 5 has two Macro keys (MACRO and MACRO2)
that allow the user to play back a series of keystrokes, at any
time, with the press of one key. For example, to set up a
sequence that will turn on your components and change the
components to the proper inputs:
Scientific Atlanta 0460
Sony
Starcom
0010, 0159
0459
1.
Press and hold SETUP until the Cinema 5’s red
light blinks twice, then release SETUP.
RE-ASSIGNING DEVICE KEYS
2.
3.
Press 9 - 9 - 5. The Cinema 5’s red light will blink
twice.
Press and release one of the MACRO keys. This
will be the key that will play back the series of key-
strokes assigned to that key.
You can use the Cinema 5 to operate a second TV or a sec-
ond VCR or any combination of seven home entertainment
components. For example, you may want your Cinema 5 to
control 1 TV, 1 Cable Converter, 1 Receiver, 1 CD Player, 1
DVD Player and 2 VCRs. To accomplish this, you must re-
assign one of the device keys to operate the desired compo-
nent, in this case, a second VCR. The chart below shows
you how to re-assign a particular device key and then set up
your new component.
4.
Begin entering the sequence of keystrokes, up to
15, that you wish to be played back when you
press the MACRO key. For example:
RCVR – POWER – TV – POWER – TV/VCR (To
change the input on the TV to VIDEO 1) –
CBL/SAT – POWER.
TV to VCRSETUP* - 992 - VCR - TV - TV - SETUP*
- VCR code
TV to DVD/LD
TV to RCVR
SETUP* - 992 - DVD/LD - TV - TV -
SETUP* - DVD or LD Player code
5.
Once your sequence is entered, press and hold
SETUP until the Cinema 5’s red light blinks twice.
SETUP* - 992 - RCVR - TV - TV -
SETUP* - Audio code
Now, using the example as above, whenever the pro-
grammed MACRO key is pressed, the Receiver would power
ON, the TV will power ON and change the input to VIDEO 1
and then the Satellite would power ON.
TV to CBL/SAT
SETUP* - 992 - CBL/SAT - TV - TV -
SETUP* - Cable/DBS code
VCR to TVSETUP* - 992 - TV - VCR - VCR -
SETUP* - TV code
Repeat steps 1 - 5 to then setup a second sequence on the
MACRO2 key.
VCR to DVD/LD
VCR to RCVR
VCR to CBL/SAT
DVD/LD to TV
SETUP* - 992 - DVD/LD - VCR - VCR -
SETUP* - DVD/LD Player code
VOLUME LOCK
SETUP* - 992 - RCVR - VCR - VCR -
SETUP* - Audio code
Volume Lock allows the user to designate which component
will control the volume in the TV, DVD/LD and CBL/SAT
modes. To set the Volume Lock to the TV mode:
SETUP* - 992 - CBL/SAT - VCR - VCR -
SETUP* - Cable/DBS code
SETUP* - 992 - TV - DVD/LD - DVD/LD -
SETUP* - TV code
1.
2.
3.
Press and hold SETUP until the Cinema 7’s red
light blinks twice, then release SETUP.
DVD/LD to VCR
SETUP* - 992 - VCR - DVD/LD - DVD/LD
Press 9 - 9 - 3. The Cinema 5’s red light will blink
twice.
- SETUP* - VCR code
DVD/LD to RCVR
DVD/LD to CBL/SAT
RCVR to TV
SETUP* - 992 - RCVR - DVD/LD -
DVD/LD - SETUP* - Audio code
Press and release TV. The Cinema 5’s red light
will blink twice.
SETUP* - 992 - CBL/SAT - DVD/LD -
DVD/LD - SETUP* - Cable/DBS code
ꢀ
Now, whenever you press VOL , VOL
VCR, DVD/LD and CBL/SAT modes your TV will control the
or MUTE in the
ꢀ
SETUP* - 992 - TV - RCVR - RCVR -
SETUP* - TV code
Download from Www.Somanuals.com. All Manuals Search And Download.
volume. If you would like to change the Volume Lock setting to
the VCR, DVD/LD or CBL/SAT modes repeat steps 1-3, only
substitute the appropriate device key. Setting the Volume Lock
to the TV, VCR, DVD/LD or CBL/SAT mode will not effect the
volume control in the RCVR mode.
3.
To de-activate the built-in sleep timer,press
POWER.
NOTE: Plugging your TV into the outlet on the back of the
Cable Converter may allow you to turn both your Cable
Converter and TV ON and OFF
You can also change the Volume Lock setting so that an
Audio component controls the volume in all device modes.
TROUBLE SHOOTING
To change the Volume Lock setting on the Cinema 5 to the
RCVR mode:
Problem
Solution
1.
2.
3.
Press and hold SETUP until the Cinema 5’s red
light blinks twice, then release SETUP.
Red light does not
blink when you
press a key?
Replace the batteries with four (4) new AAA
alkaline batteries.
Press 9 - 9 - 3. The Cinema 5’s red light will blink
twice.
The Cinema 5
Try all of the codes listed for your brand of
home entertainment component in the “Setup
Codes” section. Many setup codes may allow
for partial functionality, however, only one
setup code will operate your home entertain-
ment component correctly. Make sure that all
of the components you are setting up can
be operated with an infrared remote con-
trol.
does not operate
your home enter-
tainment compo-
nents or is not
performing com-
mands properly?
Press and release RCVR . The Cinema 5’s red
light will blink twice.
ꢀ
Now, whenever you press VOL ꢀ, VOL or MUTE your
Audio component will control the volume in all device modes.
You can also change the Volume Lock setting so that each
component controls its own volume. However, some compo-
nents do not have volume control. Using this setting may
eliminate volume control in some device modes. To change
the Volume Lock setting on the Cinema 5 so each mode
controls its own volume:
Problems pro-
gramming a
TV/VCR combo?
Try the VCR set-up codes for your brand.
However, some combo units may require both
a TV code for volume control and a VCR code
for the remaining functions.
VCR not record-
ing?
As a safety feature on the Cinema 5, you
must press the REC key twice.
1.
2.
3.
Press and hold SETUP until the Cinema 5’s red
light blinks twice, then release SETUP.
Press 9 - 9 - 3. The Cinema 5’s red light will blink
twice.
CH
/
and
Due to RCA design (1983-1987), only the
original remote control will operate these
functions.
PREV CH not
working for your
RCA TV?
ꢀ
Press and release VOL . The Cinema 5’s red
light will blink twice.
Problems chang-
ing channels?
If your original remote control required an
Enter keystroke when changing channels,
press the ENTER key on the Cinema 5 after
you enter the channel number.
ꢀ
Now, whenever you press press VOL ꢀ, VOL or MUTE on
the Cinema 5 each component will control its own volume,
provided each component has volume control.
The red light
Make sure you are aiming your Cinema 5 at
your home entertainment component and that
you are within 15 feet before using your
remote.
blinks when you
press a key but
you receive no
response from
your home enter-
tainment com-
ponent?
USING THE SLEEP KEY
The SLEEP key allows you to access the sleep timer of your
TV, Cable Converter/DBS Satellite or Audio component. You
can access your TV, Cable Converter, DBS Satellite or Audio
component’s Sleep Timer by pressing the SLEEP key. Most
Sleep Timers advance in increments of 10 or 15 minutes,
however, for specific instructions on setting your components
Sleep Timer, please consult your original owner’s manual.
Cinema 5 not
learning a com-
mand from your
original remote
control?
Make sure your remote controls are nose-to-
nose and are no more than 2 inches apart
(see diagram in step 5 on page 24).
Even if your original Cable Converter remote control did not
have a sleep timer, your Cinema 5 has its own built-in sleep
timer. If your Cable Converter does not have a sleep timer,
press the SLEEP key to activate the Cinema 5’s built-in
sleep timer. For example:
Tried “Search
Method” and still
did not find the
code?
Try the “Search Method” again after clearing
out the device key as follows: Press and hold
SETUP until red light blinks twice, then
release. Next enter 9 -9 - 2. Then press and
release the device key to be cleared twice.
1.
Press and release the CBL/SAT key then press
the SLEEP key once to set the Cinema 5’s built-in
sleep timer for 15 minutes. The red light will blink
once.
2.
Each additional press of the SLEEP key will add
15 more minutes to the Sleep Timer, up to a maxi-
mum of 60 minutes. The LED will blink twice when
the sleep timer is set for 30 minutes, 3 times for
45 minutes, or 4 times for 60 minutes.
Sony’s Picture In
Picture (PIP)
won’t turn off?
Press TV once. Press and hold SETUP until
red light blinks twice, then release. Enter 9 - 9 -
4 and press SETUP once. Then enter 6 -2 -1
and press PIP On/Off. The red light should
blink twice. PIP should operate properly now.
Sharp’s Picture In
Picture (PIP)
won’t work prop-
erly?
Sharp’s PIP feature requires separate PIP
functions for “on” and “off”.
NOTE: The sleep timer starts 10 seconds after
the last press of the SLEEP key. Once you have activated
the Cinema 5’s built-in sleep timer, you must keep the
remote control aimed directly at the component.
Download from Www.Somanuals.com. All Manuals Search And Download.
®
ONE FOR ALL PRODUCTS
For PIP “on”, press TV once. Press and hold
SETUP until red light blinks twice, then
release. Enter 9- 9-4 and press SETUP once.
Enter 3- 4-8 and press PIP On/Off. The red
light should blink twice. PIP “on” should oper-
ate properly now.
Limited Warranty
One For All (“OFA”) warrants, to the original purchaser only, that
this product will be free from defects in materials and workman-
ship, under normal use, for ninety (90) days from the date of
original purchase.
For PIP “off”, press TV once. Press and hold
SETUP until red light blinks twice, then
release. Enter 9- 9-4 and press SETUP once.
Enter 6-0-6 and press SETUP PIP On/Off.
The red light should blink twice. PIP “off”
should operate by pressing SETUP then the
PIP key.
This warranty does not cover damage or failures caused by
products or services not supplied by OFA, or which result from
accident, misuse, abuse, neglect, mishandling, misapplica-
tion, faulty installation, set-up adjustment, improper mainte-
nance, alteration, maladjustment of consumer controls, modi-
fications, commercial use, or that is attributable to acts of God.
There are no express warranties except as listed above. OFA
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSE-
QUENTIAL DAMAGES RESULTING FROM THE USE OF
THIS PRODUCT OR ARISING OUT OF ANY BREACH OF
WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMIT-
ED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion or limitation of inciden-
tal or consequential damages, or limitations on how long an
implied warranty lasts, so the above exclusions or limitations
may not apply to you. This warranty gives you specific legal
rights and you may also have other rights which vary from
state to state.
Surround on Sony
receiver will not
turn on?
Press RCVR once. Press and hold SETUP
until red light blinks twice, then release. Enter
9- 9-4 and press SETUP once. Enter 3- 9-8
and press SURROUND. Red light should blink
twice. Surround should operate now.
Sony receiver will
turn off but not
back on?
Try using the number pad on the Cinema 5 to
turn the receiver back on. For example, try
pressing 0 to turn on in the CD mode, or 4 to
turn on in the Video 1 mode. Other numeric
keys will also turn the receiver on. If this does-
n’t work, try the following:
Press RCVR once. Press and hold SETUP
until red light blinks twice, then release. Enter
9- 9 -4 and press SETUP once. Then enter 5
- 9 -1 and press POWER. The red light should
blink twice. Power should operate properly
now.
To obtain warranty service for a defective product during the
warranty period, please return the product, preferably in the
original carton, along with your purchase receipt, to the store of
original purchase. A note detailing the complaint would be help-
ful. The store, at its option, will replace or repair this product if
found to be defective.
Audio component
not fully-opera-
tional?
Audio functionality may be split between
codes. For example, Pioneer’s Tuner code
0014 works tuner presets, but only Amplifier
code 0013 works power and volume. This also
true for Sony’s Receiver code 0158 and Misc.
Audio code 0159.
One For All
(330)-405-8655
If some functionality is missing, try other
codes to see if functionality resides there.
Mini-system, book-
shelf, or boombox
not working?
These systems may operate using a CD or
Misc. Audio code. If the original remote con-
trol did not have a power key, press PL (or
STOP) to turn on (or off) the system.
As you add new components to your home entertainment
system, One For All has a remote control that will fit your
needs. Look for these exciting products at a retailer near
you.
®
One For All and Cinema 5 are trademarks of Universal
Electronics Inc.
Consumer Help Line : 1-330-593-3335
E-Mail Address : [email protected]
ONE FOR ALL® is the registered trademark of Universal
Electronics Inc. Computime International Ltd. is the
Licensee of the ONE FOR ALL® brand for USA and
Canada.
One For All is designed for compatibility in North America
excluding Mexico.
URC-5800-Cinema 5
12/00
Download from Www.Somanuals.com. All Manuals Search And Download.
|