Management Options iConverter, Serial Agent
Network Management
1: Chassis and Module Management
2: Set Module Name Preferences
Management Module Preferences
3: IP and Control Preferences
4: SNMP Preferences
iConverter 2FXM Plug-in Module QUICK START GUIDE
The Omnitron iConverter® 2FXM Network Interface Device (NID)
with integrated management provides Fast Ethernet
(100BASE-FX) fiber-to-fiber media conversion.
The 2FXM conforms to Ethernet in the First Mile (EFM) fiber
standards to support Fiber-to-the-X (FTTX) Metropolitan and
Enterprise LAN networks. Built-in Operation, Administration
and Maintenance (OAM) functionality enables the 2FXM to
operate as a managed demarcation point at the customer
premises and network edge, offering service provisioning
functions, such as Quality of Service and Bandwidth Control
(rate-limiting) capabilities.
5: Abandon Preference Changes
6: Save Preference Changes
7: Restore Factory Defaults
8: Restart Management Module
9: Other Networking Features
Management Module Maintenance
10: Firmware Update
The 2FXM module can be managed using Omnitron’s NetOutlookTM SNMP Management
Software, 3rd Party SNMP Client, Telnet or the Command Line Interface (CLI).
11: Set Date/Time
For more information, including the complete User Manual on the 2FXM Plug-in module,
access Omnitron’s documentation download web page to view all relevant documents:
IP Address = 192.168.1.220
Chassis Number = 1
Enter Choice, <H>elp, E<x>it >
INSTALLATION PROCEDURE
1) Configure DIP-Switches
Figure D: Command Line Interface Menu Options
2) Install Module in Chassis and Connect Cables
3) Configure Module via Command Line Interface
4) Verify Operation
The CLI interface allows for the detailed configuration of the module. It is recommended
to configure the module with an IP address associated with the attached network.
Also, SNMP traphost address should be configured if the module is managed with an
SNMP-based Management System. See the 2FXM User Manual for complete
information.
1) CONFIGURE DIP-SWITCHES
Switch 1
4) VERIFY OPERATION
DIP-SWITCH BANK 1
LED Function
"Legend"
Color
Amber No power
Chassis Power
Off State
On / Blinking State
Once the module has been
installed and configured per
steps 1 - 3, verify the module
is operational by viewing the
LED indicators.
Bank 2
SW1 - PAUSE ENABLE
Switch 8
Power "Pwr"
On: Module has power
When the Pause Enable DIP-switch is in the
LEFT “Off” position (factory default), the 2FXM
disables the fiber ports’ ability to send and
receive Pause frames during network
congestion. Setting this DIP-switch to the
RIGHT “On” position, enables the 2FXM to
receive Pause frames from its link partner. This
enables the 2FXM to stop transmitting traffic to
its link partner and store incoming frames from
the other port in the internal buffer until the
congestion clears. If the internal buffer of the
2FXM becomes congested, it will transmit a
Pause frame to its link partner.
On: Power available from
installed Power Supply #X
Switch 1
Power Supply Status
#X
Amber
Supply not installed Blinking: No power available
from installed Power Supply #X
Bank 1
Port 1
Switch 8
On: Fiber link is active
Blinking: Fiber Data Activity
The Power LED indicates the Fiber Link Activity
Green No Fiber Link
Green Half-Duplex
"P1"
module is receiving power
Port 1
RIGHT
LEFT
Half/Full Duplex
"FDX"
Chassis Management
Master/Slave
"Msr/Slv"
Port 2
Fiber Link Activity
"P2"
Port 2
Half/Full Duplex
"FDX"
On: Full-Duplex
from the chassis.
On: Chassis Master
Blinking: Operating in OAM
Mode
The Fiber Optic link LEDs
indicate the fiber optic
connections have been
established. Verify the Link
Mode selection is set to Link
Segment (LS). Until a stable
link is established, leave the
Link Mode configured for LS.
Chassis Slave
Green
Mode
On: Fiber link is active
Blinking: Fiber Data Activity
Green No Fiber Link
Green Half-Duplex
Figure A: DIP-Switch Locations
On: Full-Duplex
Figure E: LED Indicators
SW2 - FIBER PORT 1 FULL/HALF DUPLEX
Setting this DIP-switch to Half-Duplex “HDX” facilitates a connection that supports Half-
Duplex. Setting this DIP-switch to Full-Duplex “FDX” facilitates a connection that
supports Full-Duplex operation.
After a Link presence is established, the Link Mode selection can be modified.
Form 040-08940-002 D 12/07
Omnitron Systems Technology * 140 Technology Dr. #500 * Irvine, CA 92618
Download from Www.Somanuals.com. All Manuals Search And Download.
|