|
Oakley Sound Systems
5U Oakley Modular Series
VCO Controller
1U wide oscillator master module
User Manual
V0.0.04
Preliminary Version
More Information to follow
Tony Allgood B.Eng
Oakley Sound Systems
CARLISLE
United Kingdom
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This is the User Manual for the issue 1 VCO Controller 5U module from Oakley Sound.
This document contains a basic summary of its operation, how our Oakley Buss works, a
guide to the front panel controls, how to connect it to your modules and finally calibration
procedures.
For the Builder's Guide, which includes the parts list, schematic description and testing advice,
please visit the project webpage at:
For general information regarding where to get parts and suggested part numbers please see
For general information on how to build our modules, including circuit board population,
mounting front panel components and making up board interconnects please see our
The 5U VCO Controller Module
The Oakley VCO Controller is a 1U wide module designed to function as a master controller
for two or more VCOs.
The basic premise of this module is to make it easy to control multiple oscillators. Quite often
you will require simple vibrato of two or more VCOs. Normally this is done by patching one
LFO (low frequency oscillator) to your VCOs via a multiple. This uses up a minimum of three
patch leads for two VCOs and the vibrato depth needs to be set individually on each VCO.
With this module the internal sine wave LFO is added directly to the VCO's control buss, or
by using two of the output sockets. One pot controls the depth of the LFO for both or more
VCOs. The LFO may be overridden by inserting a jack into the CV IN socket on the module
thus allowing other CVs to control multiple VCOs simply.
The VCO Controller also features an inbuilt VCA (voltage controlled amplifier) module. This
allows the internal LFO, or any external CV, to be controlled by another CV. This CV may be
aftertouch or modulation wheel outputs from your midi-CV interface. Thus, vibrato depth can
be controlled with your keyboard or keyboard's wheel or lever. Only one patch lead is required
to add touch sensitive or wheel controlled vibrato to your patches – normally this would
require a minimum of 2U of rack space, a multiple, and a whole bunch of patch leads.
The VCA within this module can also be used separately as a ordinary VCA should you not
wish to use the other features in the module at any time.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Also available are two octave switches. These affect the two keyboard control voltage (KCV)
outputs of the module individually. This each VCO, or VCO bank, can be raised or lowered by
one octave at a flick of a switch. Each KCV output uses a low impedance cable driver to
ensure no droops with long signal runs and multiple loading.
Although this module was designed to work with the Oakley buss, which pipes around KCV
and gate signals around your modular, the input and output sockets on this module can be
assigned different purposes so as to suit individual requirements.
VCA control input is optionally low pass filtered so as to reduce stepping artefacts from midi
generated CVs. This low pass filtered output is available via the VCA CV OUT socket so you
can use it to control other modules.
The internal LFO outputs are available individually from the front panel as both sine wave (+/-
5V) and square wave (+5V, 0V).
More about the Oakley Buss and Module Normalisation
The Oakley buss is a three way connector found on various modules. Pin 1 carries the
keyboard CV (note control) and pin 3 carries gate (note on or off). The VCO Controller
module taps into the Oakley buss and creates two new busses for each VCO bank. It also has
a buss through feature for easy wiring
The word buss is perhaps a little grand for something that has just two control lines and a
single ground. However, it still adheres to the principle of a common set of conductors that is
available to all modules.
Normalising is the process by which some signal paths are already made for you. In other
words no patch leads are needed to make those connections; they are connected internally
either within the module or between different modules but behind the faceplates. However,
normalising can always be overridden by the user. The name itself comes from the use of
normalised connections on sockets. When a socket does not have a jack inserted it is in its
normal position. There is often a connection between the signal lug of the socket and an extra
contact called the NC (normally closed) lug. It is this third lug on the socket that is used for
the normalisation. Inserting a jack plug will break the connection between the NC and the
signal lug.
To help us understand where normalisation is useful consider a VCO with a 1V/octave socket
on its front panel. It is most likely to be used to for a keyboard control voltage (KCV). To
connect KCV to this socket one would ordinarily need a patch lead. But imagine a system
where you have four VCOs and two VCFs that all need the same KCV signal. It can take
many patch leads to do this; seven if you have a large multiple panel. Now suppose that the
NC lug of every 1V/octave socket is connected to a common KCV bus. All six modules can
now be driven without the need for those seven patch leads. This saves you leads, time, and
also gives you a better working environment because you don’t have to fight your way
through a tangle of leads to get to the module’s knobs. Inserting a jack into one of those
sockets would disconnect it from the KCV bus, so you still have complete modularity.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
The Oakley VCO has a Oakley Buss input header on its socket board. Pin 1 of this header is
connected to the NC lug of the 1V/octave input socket. So any voltage on pin 1 of this header
is automatically connected to the module's 1V/octave input unless as jack is inserted into that
socket.
Normalising is frowned upon by some people, and loved by others. Most modulars do have
some form of normalising. The Roland System 100 probably has the highest degree of
normalising. You don’t even need a patch lead to get that one to sing. The MOTM has no
form of external normalising, although there are normalising routes within each module.
When I first started building my own modular system, I thought that normalisation was a bad
thing. Like preset memory patches I thought it would stifle creativity by making things a little
too easy. However, in practice I noticed that I was routing CV and gate to the same locations
in my modular for almost all my patches. So I decided to provide some form of limited
normalising. I chose to normalise just KCV and gate. No audio normalisation was allowed. It
was easy to do, and proved very effective.
The issue 2 Dizzy PCB, our main form distributing power around our larger modular systems,
includes a three way normalising buss which we call the Oakley Buss. This Oakley standard,
originally created with the Dizzy issue 1 PCB, gave us just two lines; the KCV and Gate
busses. These are accessed by the three way 0.1” headers. Pin 1 of each header is KCV and
pin 3 is Gate. Pin 2 was connected to ground on the first board, but some customers modified
the board to give a third CV bus. The current issue of the Dizzy board leaves it floating so you
can now use it to normalise a third CV line if you wish. There are more details about this in
the Dizzy User Manual and Builder's Guide.
Each module that you wish to connect to the normalisation buss needs to have a suitable
length of wire terminating in a 3-way 0.1” header. You’ll probably only need to use one pin
for each module, since very few synthesiser modules actually use KCV and gate together. The
wire end of the interconnect needs to be connected to the NC lug on the relevant socket, ie.
1V/octave or gate. Be sure that you remove any existing normalising on the socket that you
want to use. Note that some MOTM and Oakley modules have the NC lug connected to
ground.
The Oakley VCO, midiDAC and other modules already have the three pin headers on the main
or socket boards ready for easy direct connection to the Dizzy or VCO Controller module.
You may feel that adding little single, or double, wire tails to your MOTM modules is not a
good idea. It is a perhaps little untidy. But I certainly would recommend to try it out if you use
your modular for straightforward musical applications.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Controls
[more to come here]
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Calibration
The unit has seven trimmers and thus may seem a little daunting to trim correctly. However,
the unit has been designed so that it is easy to set up and no special equipment is required
other than a guitar tuner or a decent set of ears.
Once the unit has warmed up nicely I recommend setting up the unit in the order that these are
presented here. I will assume that your VCOs are already in tune. If not do not attempt to trim
the VCO Controller first since it requires the VCOs to be perfectly in tune.
Turn the lower two pots to their minimum value. Ensure that the two switches are in their
middle positions.
SCL1 – This trimmer sets the scale of the KCV1 output.
If you are using the Oakley Buss your VCO will be already connected to the VCO Controller
module via the KCV1 header, and the VCO Controller will be connected to the system's
Oakley Buss or direct from the midi-DAC. You need to do the following:
Connect up your VCO so you can hear the output. Set it up so you can measure the frequency
of the VCO with a guitar tuner or suitable VST plug-in in your DAW. Now connect your
VCO's 1V/octave input to the output of your midi-CV convertor or analogue keyboard. Play a
note somewhere near the top of the keyboard. Tune in the VCO to that note as accurately as
you can with the coarse and fine controls on your VCO.
Now remove the patch lead from the VCO's 1V/octave input and your VCO will now be
receiving the KCV1 signal from the VCO Controller module. Play the same note again on the
keyboard and adjust SCL1 until it gives you exactly the same note as you heard before. Try to
be as accurate as you can.
Now play a few notes and ensure that the VCO is tracking nicely.
If you do not have the Oakley Buss then you will have to make your connections with patch
leads.
Connect up your VCO so you can hear the output. Set it up so you can measure the frequency
of the VCO with a guitar tuner or suitable VST plug-in in your DAW. Now connect your
VCO's 1V/octave input to the output of your midi-CV convertor or analogue keyboard. Play
a note somewhere near the top of the keyboard. Tune in the VCO to that note as accurately
as you can with the coarse and fine controls on your VCO.
Now connect the 1V/octave input lead to the Key-CV1 output of the VCO Controller. Unlike
those with the internal Oakley Buss you will have made this output available at the front
panel of the VCO Controller module. Connect also the Key-CV IN socket to the output of
your midi-CV convertor. The VCO Controller is now controlling the VCO's pitch. Play the
same note again on the keyboard and adjust SCL1 until it gives you exactly the same note as
you heard before. Try to be as accurate as you can.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SCL2 – This trimmer sets the scale of the KCV2 output
Repeat the above but with your second VCO and use the Key-CV2 output.
The purpose of both SCL trimmers is to ensure that the VCO Controller adds nothing to the
CV signal when the two depth pots are at their minimum settings and the switches are in their
middle positions.
+OCT – This trimmer determines the note played when any octave switch is set to +1.
Play a note somewhere in the middle of the keyboard, say a low A at 440Hz. It should be in
tune. Now flick the top switch to +1 and the VCO that is connected to KCV1 should go up in
pitch. Adjust +OCT so that the pitch is exactly one octave higher than it was when the switch
was in its middle position. Flick it back and forth a few times to make sure the interval is
exactly an octave.
-OCT – This trimmer determines the note played when any octave switch is set to -1.
Play the same note on the keyboard. Now flick the top switch to -1 and the VCO that is
connected to KCV1 should go down in pitch by about an octave. Adjust -OCT so that it is
exactly an octave lower.
Ensure that the KCV2 output is similarly affected. There should be no appreciable difference
in octave intervals between KCV1 and KCV2.
Note that tweaking +OCT will affect the -1 octave setting as well as the +1. If you tweak the
+OCT trimmer for some reason, you will have to re-tweak the -OCT one as well.
OFFSET – This trimmer adjusts the control breakthrough of the internal VCA.
Plug an unconnected patch lead into VCA IN and let the other end hang so that it doesn't
touch anything. Now connect your amp or mixer to the VCA OUT socket (not the VCA CV
OUT) so you will be able to hear what is the VCA is doing. Keep the volume down low for
the moment. Connect the SQR OUT of the module into the VCA CV IN. And turn up the
volume slowly. You should be able to hear a thumping in time with the modules LFO. Turn
the rate up a bit if its going too slow.
Now adjust the OFFSET trimmer until the thumping is minimised. You may have to turn your
amp up a bit to make sure the last remnants are reduced to their lowest settings.
Now unplug everything. It's time to create the a nice sine wave. If you have a oscilloscope
then this will be easier but if not do not fret.
Using the 'scope adjust the two trimmers, SHAPE and SYM, until you get the best shape sine
wave from the SINE OUT socket.
If you haven't got a 'scope, you can use your ears. Turn the LFO RATE pot all the way up.
Listen to the sine wave output. You will hear a deep bass tone. Adjust the SHAPE and SYM
pots until you get the dullest sound with minimal overtones.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Final Comments
I hope you enjoy using the Oakley VCO Controller.
If you have any problems with the module, an excellent source of support is the Oakley Sound
Forum at Muffwiggler.com. Paul Darlow and I are on this group, as well as many other users
and builders of Oakley modules.
If you have a comment about this user guide, or have a found a mistake in it, then please do let
me know.
Last but not least, can I say a big thank you to all of you who helped and inspired me. Thanks
especially to all those nice people on the Synth-diy, Oakley-Synths and Analogue Heaven
mailing lists.
Tony Allgood at Oakley Sound
Cumbria, UK
© February 2010
No part of this document may be copied by whatever means without my permission.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
|