Enterprise Edge
M7324N
User Card
© 2000 Nortel Networks
P0908520 Issue 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Your Enterprise Edge M7324N Telephone
Display
shows the time, date, and call information; guides you while
using features; tilts for easy viewing. The lower line of the display
is reserved for display button instructions.
Display buttons
Release button cancels active calls
Feature button
starts or ends a feature.
Hold button
Dial pad
Volume control
Indicators
appear beside active
lines and features.
Memory and line buttons
are buttons with labels for
one-touch dialing, feature
operation, or line access.
Using display buttons Three display buttons appear directly below
the display. When they are active, these
buttons are labelled in capital letters on the
bottom line of the display. In Enterprise Edge
documents, display buttons are shown as
underlined, capital letters: for example, OK.
Using Button
Inquiry
Check what is programmed on your memory buttons.
1. Release all calls or lines with dial tone.
2. Press ƒ•‚.
3. Press the button(s) that you want to check and read the display.
4. Press ƒ when finished.
Adjusting display
contrast
1. Press ƒ•‡.
2. Press UP or DOWN for the level you want.
3. Press OK when finished.
Selecting a ring
type and volume
level
1. Press ĥfl.
2. Press ⁄, ¤, ‹, ›, or NEXT to hear the different ring types.
3. While the telephone is ringing, press √ to adjust the volume
level.
4. Press OK to store the volume level and ring.
Mounting the
telephone
The M7324N telephone can be placed on any level surface. It cannot be
wall-mounted.
Page 1 Enterprise Edge M7324N User Card
Download from Www.Somanuals.com. All Manuals Search And Download.
Making and answering calls
Answering calls
Answering calls using the handset
When your telephone rings, or º flashes beside an Intercom or line button:
1. Lift the handset.
OR
Press the button beside the flashing º before lifting the handset.
Answering calls using Handsfree
When your telephone rings, or º flashes beside an Intercom or line button:
1. Press ©.
Making calls
Depending upon the dialing mode programmed on your telephone, you may
have to lift the handset before making a call.
¬
External calls using numbered line buttons
1. If you do not have an external Prime line, press a line button.
2. Dial your call.
∆
External calls using Intercom buttons
1. Lift the handset.
2. If º appears beside an Intercom button, enter a line pool access code.
OR
Press an Intercom button without º, then enter a line pool access code.
3. When you hear external dial tone, dial your call.
Internal calls using Intercom buttons
1. If you do not have an internal Prime line, press ∆.
2. Dial your call.
Note: Line pool access codes and extension numbers are supplied by your
System Administrator.
Making calls using Handsfree
1. Press ©instead of lifting the handset.
˙
Holding Calls
1. Press ˙. The º flashes beside the line on hold.
2. Press the line button with the flashing º to return to the call.
Automatic hold
Calls are put on hold automatically when you switch from one line to another.
Exclusive hold
Use Exclusive Hold (ƒ˙) to keep a call on hold so that it can be
retrieved only at your telephone.
©
This button operates your telephone’s built-in microphone and speaker. Your
System Administrator can program Handsfree for your telephone.
Switching between Handsfree and handset
1. Press © and replace the handset to switch to Handsfree.
2. Pick up the handset to switch back.
Using Mute
1. Press © to turn the microphone OFF.
2. Press © again to turn the microphone ON.
Page 2 Enterprise Edge M7324N User Card
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming memory buttons
About memory
buttons
Memory buttons are the buttons with
labels other than line or Handsfree
buttons. Memory buttons store
telephone numbers or feature codes to
give you one-touch dialling or feature
activation. You can change the function
of a memory button by programming it
with a new number or feature.
If you have programmed a memory
button with an extension number, the
indicator comes on when the number is
busy.
Remember: Press ƒ•‚ to check a memory or line button.
External Autodial
Programming
memory buttons
1. If you are on a call or a line with dial tone, press ˙ or® .
2. Press ƒ•⁄.
3. Press a memory button.
4. Dial the external number.
5. Press OK to store the number.
6. Label your new button.
Internal Autodial
1. If you are on a call or a line with dial tone, press ˙ or®.
2. Press ƒ•¤.
3. Press a memory button.
4. Dial the extension number.
5. Label your new button.
Features
1. If you are on a call or a line with dial tone, press ˙ or ®.
2. Press ƒ•‹.
3. Press a memory button.
4. Press ƒ and the feature code.
5. Label your new button.
Erasing memory buttons
1. If you are on a call or a line with dial tone, press ˙ or®.
2. Press ƒ•⁄.
3. Press the memory button you want to erase.
4. Press OK to erase the button.
Page 3 Enterprise Edge M7324N User Card
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the telephone
ATTENTION Before attempting to carry
out any work on the telephone, ensure
that the line cord is unplugged from the
wall socket.
Connecting the cords
1
2
Press here firmly
until it clicks, to
attach the stand.
To remove any of the cords, squeeze the
release latch on the plug and gently pull
the plug from the socket.
Connect the handset cord to the jack
labelled with the telephone icon and
route the cord as shown.
If you are using a headset, route the
cord along the channel in the base and
connect the cord to the telephone jack
that is marked with the headset icon.
Route the line cord through the stand
and connect the cord to the telephone
jack that is marked with the jack icon.
Attach the stand using either pair of
slots; to raise the back of the telephone
to its highest position, use these slots.
Press here to
remove the stand.
Once the above work is complete, plug
the line cord back into its wall socket.
Notice
These telephones now conform to the latest standards in
relation to the positioning of Q and Z on the number buttons.
The Q appears on button number 7 and the Z appears on
button number 9.
Page 44 Enteerprise Eddge M73244N User Card
P0908520 Issue 02
Download from Www.Somanuals.com. All Manuals Search And Download.
|