Part No. 212257-B
January 2002
4401 Great America Parkway
Santa Clara, CA 95054
Installation and Networking
Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Japan/Nippon requirements only
Voluntary Control Council for Interference (VCCI) statement
Taiwan requirements
Bureau of Standards, Metrology and Inspection (BSMI) Statement
Canada requirements only
Canadian Department of Communications Radio Interference Regulations
This digital apparatus does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in
the Radio Interference Regulations of the Canadian Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique respecte les limites de bruits radioélectriques visant les appareils numériques de classe A
prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the
Radio Interference Regulations of the Canadian Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique respecte les limites de bruits radioélectriques visant les appareils numériques de classe B
prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Warning: Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into
an optical fiber or connector port. Always assume that fiber optic cables are connected to a light source.
Warning: Vorsicht: Glasfaserkomponenten können Laserlicht bzw. Infrarotlicht abstrahlen, wodurch
Ihre Augen geschädigt werden können. Schauen Sie niemals in einen Glasfaser-LWL oder ein Anschlußteil.
Gehen Sie stets davon aus, daß das Glasfaserkabel an eine Lichtquelle angeschlossen ist.
Warning: Avertissement: L’équipement à fibre optique peut émettre des rayons laser ou infrarouges
qui risquent d’entraîner des lésions oculaires. Ne jamais regarder dans le port d’un connecteur ou d’un câble à
fibre optique. Toujours supposer que les câbles à fibre optique sont raccordés à une source lumineuse.
Warning: Advertencia: Los equipos de fibra óptica pueden emitir radiaciones de láser o infrarrojas que
pueden dañar los ojos. No mire nunca en el interior de una fibra óptica ni de un puerto de conexión. Suponga
siempre que los cables de fibra óptica están conectados a una fuente luminosa.
Warning: Avvertenza: Le apparecchiature a fibre ottiche emettono raggi laser o infrarossi che possono
risultare dannosi per gli occhi. Non guardare mai direttamente le fibre ottiche o le porte di collegamento.
Tenere in considerazione il fatto che i cavi a fibre ottiche sono collegati a una sorgente luminosa.
Nortel Networks Inc. software license agreement
NOTICE: Please carefully read this license agreement before copying or using the accompanying software or installing
the hardware unit with pre-enabled software (each of which is referred to as “Software” in this Agreement). BY
COPYING OR USING THE SOFTWARE, YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF THIS
LICENSE AGREEMENT. THE TERMS EXPRESSED IN THIS AGREEMENT ARE THE ONLY TERMS UNDER
WHICH NORTEL NETWORKS WILL PERMIT YOU TO USE THE SOFTWARE. If you do not accept these terms
and conditions, return the product, unused and in the original shipping container, within 30 days of purchase to obtain a
credit for the full purchase price.
1. License grant. Nortel Networks Inc. (“Nortel Networks”) grants the end user of the Software (“Licensee”) a personal,
nonexclusive, nontransferable license: a) to use the Software either on a single computer or, if applicable, on a single
authorized device identified by host ID, for which it was originally acquired; b) to copy the Software solely for backup
purposes in support of authorized use of the Software; and c) to use and copy the associated user manual solely in
support of authorized use of the Software by Licensee. This license applies to the Software only and does not extend to
Nortel Networks Agent software or other Nortel Networks software products. Nortel Networks Agent software or other
Nortel Networks software products are licensed for use under the terms of the applicable Nortel Networks Inc. Software
License Agreement that accompanies such software and upon payment by the end user of the applicable license fees for
such software.
2. Restrictions on use; reservation of rights. The Software and user manuals are protected under copyright laws.
Nortel Networks and/or its licensors retain all title and ownership in both the Software and user manuals, including any
revisions made by Nortel Networks or its licensors. The copyright notice must be reproduced and included with any
copy of any portion of the Software or user manuals. Licensee may not modify, translate, decompile, disassemble, use
for any competitive analysis, reverse engineer, distribute, or create derivative works from the Software or user manuals
or any copy, in whole or in part. Except as expressly provided in this Agreement, Licensee may not copy or transfer the
Software or user manuals, in whole or in part. The Software and user manuals embody Nortel Networks’ and its
licensors’ confidential and proprietary intellectual property. Licensee shall not sublicense, assign, or otherwise disclose
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
5
to any third party the Software, or any information about the operation, design, performance, or implementation of the
Software and user manuals that is confidential to Nortel Networks and its licensors; however, Licensee may grant
permission to its consultants, subcontractors, and agents to use the Software at Licensee’s facility, provided they have
agreed to use the Software only in accordance with the terms of this license.
3. Limited warranty. Nortel Networks warrants each item of Software, as delivered by Nortel Networks and properly
installed and operated on Nortel Networks hardware or other equipment it is originally licensed for, to function
substantially as described in its accompanying user manual during its warranty period, which begins on the date
Software is first shipped to Licensee. If any item of Software fails to so function during its warranty period, as the sole
remedy Nortel Networks will at its discretion provide a suitable fix, patch, or workaround for the problem that may be
included in a future Software release. Nortel Networks further warrants to Licensee that the media on which the
Software is provided will be free from defects in materials and workmanship under normal use for a period of 90 days
from the date Software is first shipped to Licensee. Nortel Networks will replace defective media at no charge if it is
returned to Nortel Networks during the warranty period along with proof of the date of shipment. This warranty does not
apply if the media has been damaged as a result of accident, misuse, or abuse. The Licensee assumes all responsibility
for selection of the Software to achieve Licensee’s intended results and for the installation, use, and results obtained
from the Software. Nortel Networks does not warrant a) that the functions contained in the software will meet the
Licensee’s requirements, b) that the Software will operate in the hardware or software combinations that the Licensee
may select, c) that the operation of the Software will be uninterrupted or error free, or d) that all defects in the operation
of the Software will be corrected. Nortel Networks is not obligated to remedy any Software defect that cannot be
reproduced with the latest Software release. These warranties do not apply to the Software if it has been (i) altered,
except by Nortel Networks or in accordance with its instructions; (ii) used in conjunction with another vendor’s product,
resulting in the defect; or (iii) damaged by improper environment, abuse, misuse, accident, or negligence. THE
FOREGOING WARRANTIES AND LIMITATIONS ARE EXCLUSIVE REMEDIES AND ARE IN LIEU OF ALL
OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Licensee is responsible for the security of its
own data and information and for maintaining adequate procedures apart from the Software to reconstruct lost or altered
files, data, or programs.
4. Limitation of liability. IN NO EVENT WILL NORTEL NETWORKS OR ITS LICENSORS BE LIABLE FOR
ANY COST OF SUBSTITUTE PROCUREMENT; SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES; OR ANY DAMAGES RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE OR
PROFITS ARISING OUT OF OR IN CONNECTION WITH THE PERFORMANCE OF THE SOFTWARE, EVEN IF
NORTEL NETWORKS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT
SHALL THE LIABILITY OF NORTEL NETWORKS RELATING TO THE SOFTWARE OR THIS AGREEMENT
EXCEED THE PRICE PAID TO NORTEL NETWORKS FOR THE SOFTWARE LICENSE.
5. Government licensees. This provision applies to all Software and documentation acquired directly or indirectly by or
on behalf of the United States Government. The Software and documentation are commercial products, licensed on the
open market at market prices, and were developed entirely at private expense and without the use of any U.S.
Government funds. The license to the U.S. Government is granted only with restricted rights, and use, duplication, or
disclosure by the U.S. Government is subject to the restrictions set forth in subparagraph (c)(1) of the Commercial
Computer Software––Restricted Rights clause of FAR 52.227-19 and the limitations set out in this license for civilian
agencies, and subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause of DFARS
252.227-7013, for agencies of the Department of Defense or their successors, whichever is applicable.
6. Use of software in the European Community. This provision applies to all Software acquired for use within the
European Community. If Licensee uses the Software within a country in the European Community, the Software
Directive enacted by the Council of European Communities Directive dated 14 May, 1991, will apply to the examination
of the Software to facilitate interoperability. Licensee agrees to notify Nortel Networks of any such intended
examination of the Software and may procure support and assistance from Nortel Networks.
7. Term and termination. This license is effective until terminated; however, all of the restrictions with respect to
Nortel Networks’ copyright in the Software and user manuals will cease being effective at the date of expiration of the
Nortel Networks copyright; those restrictions relating to use and disclosure of Nortel Networks’ confidential information
shall continue in effect. Licensee may terminate this license at any time. The license will automatically terminate if
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Licensee fails to comply with any of the terms and conditions of the license. Upon termination for any reason, Licensee
will immediately destroy or return to Nortel Networks the Software, user manuals, and all copies. Nortel Networks is not
liable to Licensee for damages in any form solely by reason of the termination of this license.
8. Export and re-export. Licensee agrees not to export, directly or indirectly, the Software or related technical data or
information without first obtaining any required export licenses or other governmental approvals. Without limiting the
foregoing, Licensee, on behalf of itself and its subsidiaries and affiliates, agrees that it will not, without first obtaining all
export licenses and approvals required by the U.S. Government: (i) export, re-export, transfer, or divert any such
Software or technical data, or any direct product thereof, to any country to which such exports or re-exports are restricted
or embargoed under United States export control laws and regulations, or to any national or resident of such restricted or
embargoed countries; or (ii) provide the Software or related technical data or information to any military end user or for
any military end use, including the design, development, or production of any chemical, nuclear, or biological weapons.
9. General. If any provision of this Agreement is held to be invalid or unenforceable by a court of competent
jurisdiction, the remainder of the provisions of this Agreement shall remain in full force and effect. This Agreement will
be governed by the laws of the state of California.
Should you have any questions concerning this Agreement, contact Nortel Networks Inc., 2375 N. Glenville Dr.,
Richardson, TX 75082.
LICENSEE ACKNOWLEDGES THAT LICENSEE HAS READ THIS AGREEMENT, UNDERSTANDS IT, AND
AGREES TO BE BOUND BY ITS TERMS AND CONDITIONS. LICENSEE FURTHER AGREES THAT THIS
AGREEMENT IS THE ENTIRE AND EXCLUSIVE AGREEMENT BETWEEN NORTEL NETWORKS AND
LICENSEE, WHICH SUPERSEDES ALL PRIOR ORAL AND WRITTEN AGREEMENTS AND
COMMUNICATIONS BETWEEN THE PARTIES PERTAINING TO THE SUBJECT MATTER OF THIS
AGREEMENT. NO DIFFERENT OR ADDITIONAL TERMS WILL BE ENFORCEABLE AGAINST NORTEL
NETWORKS UNLESS NORTEL NETWORKS GIVES ITS EXPRESS WRITTEN CONSENT, INCLUDING AN
EXPRESS WAIVER OF THE TERMS OF THIS AGREEMENT.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
How to get help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Gigabit interface converter description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Optical add drop multiplexer description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Network add/drop ring application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Optical multiplexer/demultiplexer description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
CWDM OMUX-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
CWDM OMUX-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
CWDM OMUX in a point-to-point application . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
CWDM OMUX in a ring application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
About transmission distance and optical link budget . . . . . . . . . . . . . . . . . . . . . . . . . 27
How to calculate expected loss budget . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Assumptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Point-to-point transmission distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Mesh ring transmission distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Hub and spoke transmission distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Contents
Preparing for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Electrostatic discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Installing the shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Cabling a CWDM OADM or a CWDM OMUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Cabling a CWDM OADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Cabling a four-channel CWDM OMUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
CWDM OMUX specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Tools and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Cleaning Fiber Optic Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Cleaning Single SC and FC Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Cleaning Duplex SC Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Cleaning Receptacle or Duplex Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 11 Point-to-point network configuration example . . . . . . . . . . . . . . . . . . . . . . 29
Figure 12 Mesh ring network configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 13 Hub and spoke network configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 14 Class 1M laser warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 15 Shelf with plug-in module in 19-inch rack . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 16 Cabling a CWDM OADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 17 Cabling a CWDM OMUX-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 18 Cabling an CWDM OMUX-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Figures
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Point-to-point signal loss values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Mesh ring maximum transmission distance calculations . . . . . . . . . . . . . 32
Hub and spoke signal loss values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Hub and spoke maximum transmission distance calculations . . . . . . . . . 34
CWDM OADM specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
CWDM OMUX specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Tables
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Preface
Nortel Networks* optical routing system supports high-speed data
communications in metropolitan area networks (MANs) by:
•
•
Connecting Gigabit Ethernet ports with fiber optic networks.
Combining multiple wavelengths on a single fiber to expand available
bandwidth.
The system components include:
Component
Function
CWDM Gigabit interface
converters (GBICs)
Convert signals in a switch to laser light for connection to a
fiber optic network.
Passive optical
multiplexing devices
Combine laser light signals received from GBICs onto a
single fiber for transport to the destination. Separates the
wavelengths at the destination and routes them onto
different fibers which terminate on separate GBICs.
Passive optical shelf
Houses the multiplexers.
This book contains the following topics:
•
•
•
•
•
•
“Describing the optical routing system” on page 17
“Calculating transmission distance” on page 27
“Installing the shelf, OADM, and OMUX” on page 35
“CWDM OADM specifications” on page 45
“CWDM OMUX specifications” on page 47
“Handling and cleaning fiber optic equipment” on page 49
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
14 Preface
Before you begin
This guide is intended for network administrators who have the following
background:
•
•
•
Basic knowledge of networks, and network hardware
Familiarity with networking concepts and terminology
Familiarity with Ethernet network administration and Fiber Channel
networking
Hard-copy technical manuals
You can print selected technical manuals and release notes free, directly from the
product for which you need documentation. Then locate the specific category and
model or version for your hardware or software product. Use Adobe* Acrobat
Reader* to open the manuals and release notes, search for the sections you need,
and print them on most standard printers. Go to Adobe Systems at the
www.adobe.com URL to download a free copy of the Adobe Acrobat Reader.
You can purchase selected documentation sets, CDs, and technical publications
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface 15
How to get help
If you purchased a service contract for your Nortel Networks product from a
distributor or authorized reseller, contact the technical support staff for that
distributor or reseller for assistance.
If you purchased a Nortel Networks service program, contact one of the following
Nortel Networks Technical Solutions Centers:
Technical Solutions Center
Telephone
Europe, Middle East, and Africa
North America
(33) (4) 92-966-968
(800) 4NORTEL or (800) 466-7835
(61) (2) 9927-8800
Asia Pacific
China
(800) 810-5000
Additional information about the Nortel Networks Technical Solutions Centers is
An Express Routing Code (ERC) is available for many Nortel Networks products
and services. When you use an ERC, your call is routed to a technical support
person who specializes in supporting that product or service. To locate an ERC for
your product or service, go to the http://www130.nortelnetworks.com/cgi-bin/
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
16 Preface
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Chapter 1
Describing the optical routing system
Nortel Networks* optical routing system uses coarse wavelength division
multiplexing (CWDM) in a grid of eight optical wavelengths. CWDM Gigabit
Interface Converters (GBICs) in the switch transmit optical signals from Gigabit
Ethernet ports to multiplexers in a passive optical shelf. Multiplexers combine
multiple wavelengths traveling on different fibers onto a single fiber (Figure 1).
At the receiver end of the link, demultiplexers separate the wavelengths again and
route them onto different fibers which terminate on separate CWDM GBICs at the
destination. The system supports both ring and point-to-point configurations.
Figure 1 Wavelength division multiplexing
Multiplexer
Demultiplexer
signal
signal
signal
signal
signal
signal
signal
signal
1
2
3
4
1
2
3
4
Single Fiber
= Wavelength
This chapter includes the following topics:
•
•
•
•
“Parts of the optical routing system” next
“Gigabit interface converter description” on page 18
“Optical add drop multiplexer description” on page 19
“Optical multiplexer/demultiplexer description” on page 21
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
18 Chapter 1 Describing the optical routing system
Parts of the optical routing system
The optical routing system includes the following parts:
•
•
•
•
Optical add/drop multiplexers (CWDM OADMs)
Optical multiplexer/demultiplexers (CWDM OMUXs)
Optical shelf to house the multiplexers
Table 1 shows the parts of the optical routing system, and the color matching used
to distinguish the eight wavelengths.
Table 1 Parts of the optical routing system
Multiplexer part number
Wavelength
GBIC
Optical shelf
part number
(longwave) Color code part number OADM
OMUX-4
OMUX-8
1470 nm
1490 nm
1510 nm
1530 nm
1550 nm
1570 nm
1590 nm
1610 nm
Gray
AA1419017
AA1419018
AA1419019
AA1419020
AA1419021
AA1419022
AA1419023
AA1419024
AA1402002
AA1402003
AA1402004
AA1402005
AA1402006
AA1402007
AA1402008
AA1402011
AA1402010
AA1402001
Violet
Blue
AA1402009
AA1402009
AA1402009
AA1402009
Green
Yellow
Orange
Red
Brown
Gigabit interface converter description
Nortel Networks* coarse wavelength division multiplexed Gigabit Interface
Converters (Figure 2) convert signals in a switch to laser light for connection to a
fiber optic network. A CWDM GBIC transmits and receives optical signals at one
of eight specific wavelengths.
Nortel CWDM GBICs use Avalanche Photodiode (APD) technology to improve
transmission distance and optical link budget.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Describing the optical routing system 19
Figure 2 CWDM GBIC transceiver and label
Wavelength
color code
Model number
Serial number
Bar code
Interface type
Fiber mode
Wavelength
10396EA
For more information about CWDM GBICs, including specifications, see
Installing CWDM Gigabit Interface Converters, part number 212256-B.
Optical add drop multiplexer description
The passive CWDM optical add drop multiplexer (CWDM OADM) sends and
receives signals to/from CWDM GBICs installed in the switch. It is set to a
specific wavelength that matches the wavelength of the CWDM GBIC. It adds or
drops this specific wavelength from the optical fiber and allows all other
supports two separate fiber pathways traveling in opposite directions (east and
west) so that the network remains viable even if the fiber is broken at one point on
the ring.
Figure 3 shows the single wavelength CWDM OADM network and equipment
side connections.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
20 Chapter 1 Describing the optical routing system
Figure 3 CWDM OADM network and equipment side connections
Single-wavelength OADM
RX
TX
TX
RX
RX TX
RX TX
To CWDM GBIC
To CWDM GBIC
Equipment side
The CWDM OADM (Figure 4) is installed in a 19-inch, rack-mounted 1RU
optical shelf (Figure 15).
Figure 4 CWDM OADM Front Panel
For information about installing a CWDM OADM, see “Inserting a CWDM
OADM or a CWDM OMUX” on page 38. For specifications, see “CWDM
OADM specifications” on page 45.
Network add/drop ring application
The CWDM OADM pulls off a specific wavelength from an optical ring and
other wavelengths on the ring undisturbed. CWDM OADMs are set to one of
eight supported wavelengths (Table 1).
Note: The wavelength of the CWDM OADM and the corresponding
CWDM GBIC must match (see Table 1).
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Describing the optical routing system 21
Figure 5 shows an example of two separate fiber paths in a ring configuration
traveling in opposite or east/west directions into the network.
Figure 5 CWDM OADM ring configuration example
CARRIER
HOTEL SITE
PP 8600
PP 8600
PP 8600
PP 8600
OFFICE
BUILDING A
OFFICE
BUILDING B
OADM
OADM
OMUX OMUX
PP 8600
OADM
OFFICE
BUILDING C
For information on calculating network transmission distance, see Chapter 2,
“Calculating transmission distance,” on page 27.
Optical multiplexer/demultiplexer description
CWDM wavelengths from a two-fiber (east and west) circuit. It allows you to
create uni-directional network traffic rings or point-to-point links.
The CWDM OMUX (Figure 6) is installed in a 19-inch, rack-mounted 1RU
optical shelf (Figure 15).
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
22 Chapter 1 Describing the optical routing system
Figure 6 Four-channel CWDM OMUX front panel
CWDM GBICs in the switch.
CWDM OMUX-4
Figure 7 shows the CWDM OMUX-4 version, with four CWDM GBIC
equipment side connections.
Figure 7 CWDM OMUX-4 network and equipment side connections
RX
CWDM OMUX-4
TX
RX TX RX TX
RX TX RX TX
To Equipment side CWDM GBICs
CWDM OMUX-8
Figure 8 shows the CWDM OMUX-8 version, with eight CWDM GBIC
equipment side connections.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Describing the optical routing system 23
Figure 8 CWDM OMUX-8 network and equipment side connections
RX
CWDM OMUX-8
TX
RX TXRX TXRX TX RX TX RX TX RX TX RX TX RX TX
To Equipment side CWDM GBICs
For information about installing a CWDM OMUX, see “Inserting a CWDM
OADM or a CWDM OMUX” on page 38. For specifications, see “CWDM
OMUX specifications” on page 47.
CWDM OMUX in a point-to-point application
Point-to-Point (PTP) optical networks carry data directly between two end points
without branching out to other points or nodes. PTP connections (Figure 9) are
made between mux/demuxs at each end. PTP connections transport many gigabits
of data from one location to another, such as linking two data centers to become
one virtual site, mirroring two sites for disaster recovery, or providing a large
amount of bandwidth between two buildings. The key advantage of a PTP
topology is the ability to deliver maximum bandwidth over a minimum amount of
fiber.
Each CWDM OMUX supports one network backbone connection and four or
eight connections to CWDM GBICs in the switch. Typically, two CWDM
OMUXs are installed in a chassis. The CWDM OMUX on the left is called the
east path and the CWDM OMUX on the right is called the west path.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
24 Chapter 1 Describing the optical routing system
Figure 9 CWDM OMUX point-to-point configuration example
CARRIER
HOTEL SITE A
CARRIER
HOTEL SITE B
PP 8600
PP 8600
PP 8600
PP 8600
OMUX
OMUX
OMUX
OMUX
10325EA
For information about calculating network transmission distance, see Chapter 2,
CWDM OMUX in a ring application
CWDM OMUXs are also used as the hub site in CWDM OMUX-based ring
applications (Figure 10). Two CWDM OMUXs are installed in the optical shelf at
the central site to create an east and a west fiber path. The CWDM OMUX on the
left is typically called the east path and the one on the right is called the west path.
This way the east CWDM OMUX terminates all the traffic from the east
equipment port of each OADM on the ring and the west CWDM OMUX
terminates all of the traffic from the west equipment port of each OADM on the
ring. In this configuration the network remains viable even if the fiber is broken at
any point on the ring.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Describing the optical routing system 25
Figure 10 CWDM OMUX ring configuration example
CARRIER
HOTEL SITE
PP 8600
PP 8600
PP 8600
PP 8600
OFFICE
BUILDING A
OFFICE
BUILDING B
OADM
OADM
OMUX OMUX
PP 8600
OADM
OFFICE
BUILDING C
10326EA
For information about calculating network transmission distance, see Chapter 2,
“Calculating transmission distance,” on page 27.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
26 Chapter 1 Describing the optical routing system
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Chapter 2
Calculating transmission distance
CWDM network configuration.
This chapter includes the following topics:
•
•
•
•
“About transmission distance and optical link budget” next
“Point-to-point transmission distance” on page 29
“Mesh ring transmission distance” on page 30
“Hub and spoke transmission distance” on page 33
About transmission distance and optical link budget
By calculating the optical link budget, you can determine a link’s transmission
distance, or the amount of usable signal strength between the point where it
originates and the point where it terminates. The loss budget, or optical link
budget, is the amount of optical power launched into a system that is expected to
be lost through various mechanisms acting on the system, such as the absorption
of light by molecules in an optical fiber. Factors that affect transmission distance
include:
•
•
•
•
fiber optic cable attenuation (typically 0.25 dB - 0.3 dB per kilometer)
network devices the signal passes through
connectors
repair margin (user-determined)
Note: Insertion loss budget values for the optical routing system CWDM
OADM and CWDM OMUX include connector loss.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
28 Chapter 2 Calculating transmission distance
How to calculate expected loss budget
To calculate the expected loss budget for a proposed network configuration:
1
2
3
Identify all points where signal strength will be lost.
Calculate the expected loss for each point.
Add the expected losses together.
How to calculate maximum transmission distance
The examples in this chapter use the following assumptions and procedure for
calculating the maximum transmission distances for networks with CWDM
GBICs, CWDM OADMs, and CWDM OMUXs.
Assumptions
The examples assume use of the values and information listed in Table 2.
Table 2 Assumptions used in calculating maximum transmission distance
Item
Assumption
Cable
Single mode fiber optic cable (SMF)
01
Repair margin
Maximum link budget
System margin
30 dB2
3 dB (allowance for misc. network loss)
.25 dB per kilometer
Fiber attenuation
Operating temperature
CWDM OADM expected loss3
CWDM OMUX expected loss3
0 - 40°C (32 - 104°F)
Use of “CWDM OADM specifications” on page 45
Use of “CWDM OMUX specifications” on page 47
1
Use your organization’s expected repair margin for percentage of the total fiber plant loss for each
site-to-site fiber span.
2
3
From specifications in Installing CWDM Gigabit Interface Converters, part number 212256-B
Multiplexer loss values include connector loss.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Calculating transmission distance 29
Procedure
To calculate the maximum transmission distance for a proposed network
configuration:
1
2
3
4
Identify all points where signal strength will be lost.
Calculate the expected loss for each point.
Find total passive loss by adding the expected losses together.
Find remaining signal strength by subtracting passive loss, and system margin
from total system budget.
5
Find maximum transmission distance by dividing remaining signal strength
by expected fiber attenuation/km.
Point-to-point transmission distance
The following factors affect signal strength, and determine point-to-point link
budget and maximum transmission distance for the network in Figure 11:
•
•
•
CWDM OMUX mux loss
CWDM OMUX demux loss
Fiber attenuation
The Ethernet switch host does not have to be near the CWDM OMUX, and the
CWDM OMUX does not regenerate signal. Therefore, maximum transmission
distance is from GBIC to GBIC.
Figure 11 Point-to-point network configuration example
Transmission Distance
(GBIC to GBIC)
OMUX-8
OMUX-8
GBIC
GBIC
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
30 Chapter 2 Calculating transmission distance
Table 3 shows typical loss values that can be used to calculate the transmission
distance for the point-to-point network in Figure 11.
Table 3 Point-to-point signal loss values
Signal loss element
value (dB)
Loss budget
30 dB
CWDM OMUX-8 mux loss
CWDM OMUX-8 demux loss
System margin
3.5 dB
4.5 dB
3 dB
Fiber attenuation
.25 dB per km
Table 4 shows calculations used to determine maximum transmission distance for
the point-to-point network example in Figure 11.
Table 4 Point-to-point maximum transmission distance calculations
Result
Calculation
Passive loss
mux loss + demux loss
Implied fiber loss
loss budget – passive loss – system margin
implied fiber loss ÷ attenuation per kilometer
Maximum transmission distance
Transmission distance calculation for the point-to-point network example in
Figure 11:
•
•
•
3.5 dB + 4.5 dB= 8.0 dB Passive Loss
30 dB –8 dB –3 dB= 19 dB Implied Fiber Loss
19 dB ÷ .25 dB= 76 km Maximum Transmission Distance
Mesh ring transmission distance
The transmission distance calculation for the mesh ring configuration in Figure 12
is similar to that of the point-to-point configuration with some additional loss
generated in the passthrough of intermediate CWDM OADM nodes.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Calculating transmission distance 31
As it passes from point A to point B (the most remote points in the mesh ring
optic cable, and in each connection between the individual CWDM OADMs and
CWDM GBICs.
The following factors determine mesh ring link budget and transmission distance
for the network in Figure 12:
•
•
•
•
CWDM OADM insertion add loss
CWDM OADM insertion drop loss
Passthrough insertion loss at intermediate nodes
Fiber attenuation of 0.25 dB per kilometer
The Ethernet switch host does not have to be near the CWDM OADM, and the
CWDM OADM does not regenerate signal. Therefore, maximum transmission
distance is from GBIC to GBIC.
The number of OADMs supported is based on loss budget calculations.
Figure 12 Mesh ring network configuration
Transmission Distance
(GBIC to GBIC)
OADM
OADM
OADM
OADM
OADM
OADM
OADM
OADM
A
B
GBIC
GBIC
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
32 Chapter 2 Calculating transmission distance
Table 5 shows typical loss values that can be used to calculate the transmission
distance for the mesh ring network example in Figure 12.
Table 5 Mesh ring signal loss values
Signal loss element
value
Loss budget
30 dB
CWDM OADM insertion add loss
CWDM OADM insertion passthrough loss
System margin
1.9 dB
2.0 dB
2.3 dB
3 dB
Fiber attenuation
.25 dB per km
Table 6 shows the calculations used to determine maximum transmission distance
for the mesh ring network example in Figure 12.
Table 6 Mesh ring maximum transmission distance calculations
Result
Calculation
Passthrough nodes
Passive loss
nodes – 2
OADM add + OADM drop + (passthrough nodes × OADM passthrough loss)
loss budget – passive loss – system margin
implied fiber loss ÷ attenuation per kilometer
Implied fiber loss
Maximum transmission
distance
Transmission distance calculation for the mesh ring network example in
Figure 12:
•
•
•
•
8 nodes – 2= 6 Passthrough nodes
1.9 dB + 2.3 dB + (6 nodes × 2.0 dB)= 16.2 dB Passive Loss
30 dB –16.2 dB –3 dB= 10.8 dB Implied Fiber Loss
10.8 dB ÷ .25 dB= 43.2 km Maximum Transmission Distance
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Calculating transmission distance 33
Hub and spoke transmission distance
Hub and Spoke topologies are the most complex. The characteristics of all
components designed into the network must be considered in calculating
transmission distance. The following factors determine maximum transmission
distance for the hub and spoke configuration in Figure 13:
•
•
•
•
CWDM OADM insertion add loss
CWDM OADM insertion drop loss
Passthrough insertion loss for intermediate nodes
Fiber attenuation of 0.25 per kilometer
The Ethernet switch host does not have to be near the CWDM OADM, and the
CWDM OADM does not regenerate signal. Therefore, maximum transmission
distance is from GBIC to GBIC.
As the signal in Figure 13 passes from point A to point B (the most remote points
in the hub and spoke), it is expected to lose strength in the fiber optic cable, and in
each connection between the individual CWDM OADMs, the CWDM OMUX-8,
and the CWDM GBICs. The number of OADMs that can be supported is based on
the loss budget calculations.
Figure 13 Hub and spoke network configuration
Transmission Distance
(GBIC to GBIC)
OADM
OADM
OADM
OADM
OADM
OADM
OADM
OMUX-8
OADM
GBIC
GBIC
B
A
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
34 Chapter 2 Calculating transmission distance
Table 7 shows typical loss values that can be used to calculate the transmission
distance for the hub and spoke network in Figure 13.
Table 7 Hub and spoke signal loss values
Signal loss element
value
Loss budget
30 dB
CWDM OADM insertion add loss
CWDM OADM passthrough loss
System margin
1.9 dB
2.0 dB
4.5 dB
3 dB
Fiber attenuation
.25 dB per km
Table 8 shows the calculations used to determine maximum transmission distance
for the hub and spoke network in Figure 13.
Table 8 Hub and spoke maximum transmission distance calculations
Result
Calculation
Passthrough nodes
Passive loss
the number of OADMs between add OADM and OMUX
OADM add + OMUX8 demux + (passthrough nodes × OADM passthrough loss)
loss budget – passive loss – system margin
Implied fiber loss
Maximum transmission
distance
implied fiber loss ÷ attenuation per kilometer
Transmission distance calculation for the hub and spoke network example in
Figure 13:
•
•
•
•
7 Passthrough nodes
1.9 dB + 4.5 dB + (7 × 2.0)= 20.4 dB Passive Loss
30 dB –20.4 dB –3 dB= 6.6 dB Implied Fiber Loss
6.6 dB ÷ .25 dB= 26.4 km Maximum Transmission Distance
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Chapter 3
Installing the shelf, OADM, and OMUX
includes the following topics.
•
•
•
•
•
“Preparing for installation” next
“Installing the shelf” on page 37
“Inserting a CWDM OADM or a CWDM OMUX” on page 38
“Removing a CWDM OADM or a CWDM OMUX” on page 44
“Cabling a CWDM OADM or a CWDM OMUX” on page 39
Preparing for installation
•
•
•
•
“Exceeding class 1 power level warning” next
“Environmental and physical requirements” on page 36
“Electrostatic discharge” on page 36
“Handling and cleaning fiber optic equipment” on page 49
Exceeding class 1 power level warning
Muxing together several CWDM GBICs can produce a radiant power level in the
fiber which exceeds the class 1 laser Limit. The warning in Figure 14 appears on
the CWDM OMUX.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
36 Chapter 3 Installing the shelf, OADM, and OMUX
Figure 14 Class 1M laser warning
LASER RADIATION
DO NOT VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS (MAGNIFIERS)
CLASS 1M LASER PRODUCT
TOTAL RADIANT POWER LEVEL 30 MILLIWATTS
WAVELENGTH RANGE 1450 TO 1650 NM
Warning: Never look directly at the output of a fiber which contains
muxed CWDM GBICs, especially with a magnifier. Fiber optic
equipment can emit laser light that can injure your eyes.
Environmental and physical requirements
The optical routing system is mounted in an optical shelf with connections at the
front of the module. For user access to these connections, a minimum of 36 inches
Caution: To minimize contamination, keep protective caps on all fiber
optic connectors when not in use. For more information about handling
fiber optic cables, see “Handling and cleaning fiber optic equipment” on
page 49.
Electrostatic discharge
To prevent equipment damage, observe the following electrostatic discharge
(ESD) precautions when handling or installing the components.
•
Ground yourself and the equipment to an earth or building ground. Use a
grounded workbench mat (or foam that dissipates static charge) and a
grounding wrist strap. The wrist strap should touch the skin and be grounded
through a one megohm resistor.
•
•
Do not touch anyone who is not grounded.
Leave all components in their ESD-safe packaging until installation, and use
only a static-shielding bag for all storage, transport, and handling.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the shelf, OADM, and OMUX 37
•
Clear the area of synthetic materials such as polyester, plastic, vinyl, or
styrofoam because these materials carry static electricity that damages the
equipment.
Installing the shelf
To install the optical shelf (Figure 15) in a standard 19-inch equipment rack:
1
Support the chassis so that all of the mounting holes in the optical shelf are
aligned with the corresponding holes in the rack.
2
3
Attach two rack mounting bolts to each side of the rack.
Tighten all of the bolts in rotation.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
38 Chapter 3 Installing the shelf, OADM, and OMUX
Figure 15 Shelf with plug-in module in 19-inch rack
Fail
Pass
Optical shelf
10334FA
Inserting a CWDM OADM or a CWDM OMUX
CWDM OADMs and CWDM OMUXs are passive devices that require no power
for their operation. You can insert them in the optical shelf (Figure 15) and then
connect them into your network.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the shelf, OADM, and OMUX 39
To insert a CWDM OADM or a CWDM OMUX in the optical shelf:
2
3
Gently push the plug-in module into the shelf cavity.
Tighten the captive screws.
The module is installed. To cable equipment and network connections, see
“Cabling a CWDM OADM or a CWDM OMUX” on page 39.
Cabling a CWDM OADM or a CWDM OMUX
This section includes the following cabling procedures:
•
•
•
“Cabling a CWDM OADM” next
“Cabling a four-channel CWDM OMUX” on page 41
Before you attach fiber optic cable to an optical routing device, review the
following:
•
•
“Handling and cleaning fiber optic equipment” on page 49
Table 1, Parts of the optical routing system
Cabling a CWDM OADM
This section describes how to cable the following:
•
•
CWDM GBIC to CWDM OADM (Figure 16)
CWDM OADM to network backbone interfaces (Figure 16)
To connect the CWDM OADM plug-in module:
1
Make sure you have the correct CWDM GBIC for your network configuration
by matching the color of the CWDM GBIC label to the color of the connector
label on the OADM (see Table 1 on page 18).
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
40 Chapter 3 Installing the shelf, OADM, and OMUX
2
Insert the wavelength-specific CWDM GBICs into their respective network
device(s). To install a CWDM GBIC, see Installing CWDM Gigabit Interface
Converters, part number 212256-B.
3
4
Clean all fiber optic connectors on the cabling (see “Handling and cleaning
fiber optic equipment” on page 49).
Connect the fiber optic cables from the CWDM GBIC transmit (TX) and
receive (RX) connectors to the OADM Equipment RX and TX equipment
connectors (Figure 16).
5
Make the following network backbone connections (Figure 16):
•
Connect the west network backbone fiber optic cable to the OADM west
connector.
•
Connect the east backbone fiber optic cable to the OADM east connector
(Figure 16).
Figure 16 Cabling a CWDM OADM
TX
TX
WEST
RX
TX
RX
TX
RX
OADM-1-49
1490nm
EAST
10332EA
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the shelf, OADM, and OMUX 41
Cabling a four-channel CWDM OMUX
This section describes how to cable the following:
•
•
CWDM GBIC to a CWDM OMUX-4 (Figure 17)
CWDM OMUX-4 to west and east network backbone interfaces (Figure 17)
To connect fiber optic cables to a CWDM OMUX-4:
1
Insert the wavelength-specific CWDM GBICs into their respective network
device(s). To install a CWDM GBIC, see Installing CWDM Gigabit Interface
Converters, part number 212256-B.
2
3
Clean all fiber optic connectors on the cabling (see “Handling and cleaning
fiber optic equipment” on page 49).
Connect the fiber optic cables from the CWDM GBIC TX and RX to the
CWDM OMUX-4 Equipment RX and TX equipment connectors (Figure 17).
Figure 17 Cabling a CWDM OMUX-4
TX
R
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
MUX/
DEMUX-4
MUX/
DEMUX-4
10329EA
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
42 Chapter 3 Installing the shelf, OADM, and OMUX
equipment connector wavelength.
The TX of one device must always connect to the RX of the next device.
4
Make the following network backbone connections (Figure 17):
•
Connect the network backbone east fiber optic cables to the east (left)
CWDM OMUX-4.
•
Connect the network backbone west fiber optic cables to the west (right)
CWDM OMUX-4.
Cabling an eight-channel CWDM OMUX
This section describes how to cable the following:
•
•
CWDM GBIC to a CWDM OMUX-8 (Figure 18)
Note: The CWDM OMUX-8 located on the left side of the chassis
terminates the east network backbone connection. The CWDM OMUX-8
on the right side of the chassis terminates the west network backbone
connection. See Figure 18.
To connect a CWDM OMUX-8:
1
Install the CWDM GBICs (wavelength specific) into the network device(s).
To install a CWDM GBIC, see Installing CWDM Gigabit Interface
Converters, part number 212256-B.
2
3
Clean all fiber optic connectors on the cabling (see “Handling and cleaning
fiber optic equipment” on page 49).
Connect the fiber optic cables from the CWDM GBIC TX and RX connectors
to the CWDM OMUX-8 RX and TX connectors (Figure 18).
Note: The wavelength of the CWDM GBIC must match the wavelength
of the CWDM OMUX-8 equipment connector.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Installing the shelf, OADM, and OMUX 43
Make the following network backbone connections (Figure 18):
4
•
Connect the network backbone east fiber optic cables to the east (left)
CWDM OMUX-8.
•
Connect the network backbone west fiber optic cables to the west (right)
CWDM OMUX-8.
Figure 18 Cabling an CWDM OMUX-8
TX
TX
MUX/
DEMUX-8
R
MUX/
DEMUX-8
RX
10328EA
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
44 Chapter 3 Installing the shelf, OADM, and OMUX
Removing a CWDM OADM or a CWDM OMUX
CWDM OADMs and CWDM OMUXs are passive devices that require no power
for their operation. You can remove them from the optical shelf (Figure 15) after
disconnecting them from your network.
To remove a CWDM OADM or a CWDM OMUX plug-in module from the
optical shelf:
1
2
3
4
Disconnect the network cabling from the multiplexer.
Loosen the captive screws on both sides of the module.
To release the module, gently pull on both screws at the same time.
Slide the module out of the shelf.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Appendix A
CWDM OADM specifications
Table 9 CWDM OADM specifications
Item
Specification
Physical Dimensions
Plug-in Module Size
Rack Mount
8.35” x 1.7" x 10.4"
1RU
Connectors
Network Side
Equipment Side
2 dual SC/PC
2 dual SC/PC
Cabling
SMF, 9 µm
Environment
Storage
0 to 600C
40 to 850C
Wavelength Usage
Uni-directional
Typical insertion loss*
TX Equipment to RX Network (add)
RX Equipment to TX Network (drop)
Passthrough (Network to Network)
1.2 dB
1.6 dB
1.5 dB
Maximum insertion loss*
Sigma
TX Equipment to RX Network (add)
RX Equipment to TX Network (drop)
Passthrough (Network to Network)
1.9 dB
2.3 dB
2.0 dB
TX Equipment to RX Network (add)
RX Equipment to TX Network (drop)
Passthrough (Network to Network)
.35 dB
.35 dB
.40 dB
Isolation
TX Equipment to RX Network (add)
RX Equipment to TX Network (drop)
Passthrough (Network to Network)
> 25 dB
> 50 dB
> 28 dB
Passband
Directivity
Optical
Centerwavelength
+/- 5nm
< 55 dB
Wavelengths†
1471 nm
1491 nm
1511 nm
1531 nm
1551 nm
1571 nm
1591 nm
1611 nm
*
Multiplexer loss values include connector loss.
†
There is a one nanometer offset between the stated wavelength for the CWDM GBICs and the CWDM OADMs
due to a shift in the center wavelength of the CWDM GBIC as it reaches typical system operating temperature.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
46 Appendix A CWDM OADM specifications
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Appendix B
CWDM OMUX specifications
Table 10 CWDM OMUX specifications
Item
Specification
Physical Dimensions
Plug-in Module Size
Rack Mount
8.35” x 1.75" x 8.7"
1RU
OMUX-4
1 dual SC/PC
4 dual SC/PC
OMUX-8
1 dual SC/PC
8 dual SC/PC
Connectors
Network Side
Equipment Side
Cabling
SMF, 9 µm
Environment
Operating
Storage
0 to 600C
40 to 850C
OMUX-4
1.4 dB
2.4 dB
OMUX-8
2.5 dB
3.5 dB
Typical insertion loss*
TX Equipment to RX Network (Mux)
RX Equipment to TX Network (Demux)
OMUX-4
2.2 dB
OMUX-8
3.5 dB
Maximum insertion loss*
Sigma
TX Equipment to RX Network (Mux)
RX Equipment to TX Network (Demux)
3.2 dB
4.5 dB
OMUX-4
0.4 dB
0.4 dB
OMUX-8
0.5 dB
0.5 dB
TX Equipment to RX Network (Mux)
RX Equipment to TX Network (Demux)
OMUX-4
> 10 dB
> 50 dB
OMUX-8
> 10 dB
> 50 dB
Isolation
Mux
Demux
Directivity
< –55 dB
Optical OMUX4
Wavelengths†
OMUX-4
1491 nm
1531 nm
1571 nm
1611 nm
OMUX-8
1471 nm
1491 nm
1511 nm
1531 nm
1551 nm
1571 nm
1591 nm
1611 nm
*
Multiplexer loss values include connector loss.
†
There is a one nanometer offset between the stated wavelength for the CWDM GBICs and the CWDM OADMs
due to a shift in the center wavelength of the CWDM GBIC as it reaches typical system operating temperature.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
48 Appendix B CWDM OMUX specifications
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Appendix C
Handling and cleaning fiber optic equipment
Precautions
Danger: Do not look into the end of fiber optic cable. The light source used in
fiber optic cables can damage your eyes.
Warning: To prevent damage to the glass fiber, make sure you know how to
handle fiber optic cable correctly.
Warning: Do not crush fiber optic cable. If fiber optic cable is in the same
tray or duct with large, heavy electrical cables, it can be damaged by the
weight of the electrical cable.
Although the glass optical path of fiber optic cable is protected with reinforcing
material and plastic insulation, it is subject to damage. Use the following
precautions to avoid damaging the glass fiber.
•
•
•
•
Do not kink, knot, or vigorously flex the cable.
Do not bend the cable to less than a 40 mm (1.5-inch) radius.
Do not stand on fiber optic cable; and keep the cable off the floor.
Do not pull fiber optic cable any harder than you would a cable containing
copper wire of comparable size.
•
Do not allow a static load of more than a few pounds on any section of the
cable.
•
•
Place protective caps on fiber optic connectors that are not in use.
Store unused fiber optic patch cables in a cabinet, on a cable rack, or flat on a
shelf.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
50 Appendix C Handling and cleaning fiber optic equipment
Frequent overstressing of fiber optic cable causes progressive degeneration that
leads to failure.
If you suspect damage to a fiber optic cable, either due to mishandling or an
abnormally high error rate observed in one direction, reverse the cable pairs. If the
high error rate appears in the other direction, replace the cable.
Tools and Materials
You need the following tools and materials to clean fiber optic connectors.
•
•
•
•
Lint-free, non-abrasive wiping cloths
Cotton swabs, with a tightly wrapped and talcum-free tip
Optical-grade isopropyl alcohol (IPA)
Canned compressed gas with extension tube
Warning: To prevent oil contamination of connectors, do not use
commercial compressed air or house air in place of compressed gas.
Cleaning Fiber Optic Connectors
You must perform the following maintenance procedures to ensure that optical
sure connectors are covered when not in use.
This section contains the following procedures for cleaning fiber optic assemblies:
•
•
•
“Cleaning Single SC and FC Connectors” next
“Cleaning Duplex SC Connectors” on page 52
“Cleaning Receptacle or Duplex Devices” on page 53
Danger: To avoid getting debris in your eyes, wear safety glasses when
working with the canned air duster.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Handling and cleaning fiber optic equipment 51
Danger: To avoid eye irritation on contact, wear safety glasses when
working with isopropyl alcohol.
Caution: To prevent further contamination, clean fiber optic equipment
only when there is evidence of contamination.
Caution: To prevent contamination, make sure the optical ports of all
active devices are covered with a dust cap or optical connector.
Caution: To avoid the transfer of oil or other contaminants from your
fingers to the end face of the ferrule, handle connectors with care.
Before connecting them to transmission equipment, test equipment, patch panels,
or other connectors, clean all fiber optic connectors. The performance of an
optical fiber connector depends on how clean the connector and coupling are at
the time of connection. Use the following cleaning procedures when analyzing
fiber connector integrity.
If a connector performs poorly after cleaning, visually inspect the connector to
determine the possible cause of the problem and to determine if it needs replacing.
Cleaning Single SC and FC Connectors
To clean single SC and FC connectors:
1
2
3
Remove dust or debris by applying canned air to the cylindrical and end-face
surfaces of the connector.
Gently wipe the cylindrical and end-face surfaces with a pad or a wipe
dampened with optical-grade isopropyl alcohol.
Gently wipe the cylindrical and end-face surfaces with a dry, lint-free tissue.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
52 Appendix C Handling and cleaning fiber optic equipment
Dry the connector surfaces by applying canned air or letting them air dry.
4
Caution: To prevent contamination, do not touch the connector surfaces
after cleaning; and cover them with dust caps if you are not going to use
them right away.
Cleaning Duplex SC Connectors
To clean duplex connectors:
1
To remove or retract the shroud, do one of the following.
•
On removable shroud connectors, hold the shroud on the top and bottom
at the letter designation, apply medium pressure, and pull it free from the
connector body. Do not discard the shroud.
•
On retractable shroud connectors, hold the shroud in its retracted position.
2
3
4
Remove dust or debris from the ferrules and connector face with the canned
air duster.
Gently wipe the cylindrical and end-face surfaces of both ferrules using a
wipe saturated with optical-grade isopropyl alcohol.
Gently wipe the cylindrical and end-face surfaces of the connector with
Texwipe cloth (or dry lint-free tissue).
5
6
Blow dry the connector surfaces with canned air.
Using care to not touch the clean ferrules, gently push the shroud back onto
the connector until it seats and locks in place.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Handling and cleaning fiber optic equipment 53
Cleaning Receptacle or Duplex Devices
Note: To avoid contamination, optical ports should only be cleaned when
there is evidence of contamination or reduced performance, or during
their initial installation.
To clean receptacle or duplex devices:
Warning: To prevent oil contamination, do not use commercial
compressed air.
Warning: Do not allow the tube to touch the bottom of the optical port.
1
2
Remove dust or debris by blowing canned air into the optical port of the
device using the canned air extension tube.
Clean the optical port by inserting a small dry swab into the receptacle and
rotating it.
Note: Each cleaning wand should only be used to clean one optical port.
3
Reconnect the optical connector and check for proper function.
If problems persist, repeat steps 1 and 2.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
54 Appendix C Handling and cleaning fiber optic equipment
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Glossary
attenuation
The decrease in signal strength in an optical fiber caused by absorption and
scattering. Attenuation can be calculated to express
•
•
signal loss between two points
total signal loss of a telecommunications system or segment
attenuator
A device inserted into the electrical or optical path to lessen or weaken the
signal.
bandwidth
The range of frequencies within which a fiber-optic medium or terminal
device can transmit data or information.
cable
One or more optical fibers enclosed within protective covering(s) and strength
members to provide mechanical and environmental protection for the optical
fibers.
cable assembly
An optical-fiber cable with connectors installed on one or both ends. The
general purpose of the cable assembly is to interconnect the cabling system
with opto-electronic equipment at either end of the system. Cable assemblies
with connectors on one end only are called pigtails. Assemblies with
connectors on both ends are typically called jumpers or patch cords.
cable plant
The cable plant consists of all the optical elements such as fiber connectors
and splices between a transmitter and a receiver.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
56 Glossary
CD-ROM
compact disc read-only memory
A compact disc with pre-recorded data, normally used in large database-type
applications such as directory, reference, or data retrieval.
channel
A communications path or the signal sent over that path. By multiplexing
several channels, voice channels can be transmitted over one optical channel.
CO
central office
A major equipment center designed to serve the communication traffic of a
specific geographical area.
configuration
The relative arrangements, options, or connection pattern of a system and its
subcomponent parts and objects.
configure
The process of defining an appropriate set of collaborating hardware and
software objects to solve a particular problem.
CWDM
coarse wavelength division multiplexing
A technology that allows two or four optical signals with different
wavelengths to be simultaneously transmitted in the same direction over one
fiber, and then separated by wavelength at the distant end.
dB
decibel
A unit of measure indicating relative optic power on a logarithmic scale.
Often expressed to a fixed value, such as dBm (1 milliwatt) or dBµ
(1 microwatt).
dBm
decibels above one milliwatt
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary 57
demultiplexing
The separating of different wavelengths in a wavelength-division
multiplexing system. The opposite of multiplexing.
dispersion
The broadening of input pulses as they travel the length of an optical fiber.
There are three major types of dispersion, as follows:
•
•
•
modal dispersion, which is caused by the many optical path lengths in a
multimode fiber
chromatic dispersion, which is caused by the differential delay at various
wavelengths in the optical fiber
waveguide dispersion, which is caused by light traveling through both the
core and cladding materials in single-mode fibers
DWDM
dense wavelength division multiplexing
A technology that allows a large number of optical signals (usually 16 or
more) with different wavelengths to be simultaneously transmitted in the
same direction over one fiber, and then separated by wavelength at the distant
end.
ESD
electrostatic discharge
Discharge of stored static electricity that can damage electronic equipment
and impair electrical circuitry, resulting in complete or intermittent failures.
Ethernet
A local area network data link protocol based on a packet frame. Ethernet,
which usually operates at 10 Mbit/s, allows multiple devices to share access to
the link.
facility
Any provisional configuration that provides a transmission path between two
or more locations without terminating or signalling equipment. Also, the
logical representation of a transport signal.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
58 Glossary
fiber
See optical fiber.
fiber loss
Also optical fiber loss. The attenuation of the light signal in optical-fiber
transmission.
fiber-optic link
A combination of transmitter, receiver, and fiber-optic cable capable of
transmitting data.
FO
fiber optics
The branch of optical technology dedicated to transmitting light through
fibers made of transparent materials such as glass and plastic.
GBIC
Gigabit interface converter
Allows Gigabit Ethernet ports to link with fiber optic networks.
Gbit/s
Gigabits per second
A measure of the bandwidth on a data transmission medium. One Gbit/s
equals 1,000,000,000 bps.
Gigabit Ethernet
Gigabit Ethernet
A LAN transmission standard that provides a data rate of one billion bits per
second (Gbit/s).
ground
An electrical term meaning to connect to the earth or other large conducting
body to serve as an earth thus making a complete electrical circuit.
GUI
graphical user interface
A graphical (rather than textual) interface to a computer.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary 59
hub
A group of circuits connected at one point on a network.
insertion loss
In an optical fiber system, the total optical power loss caused by insertion of
an optical component, such as a connector, splice, or coupler. Usually given in
dB.
kbps
thousands of bits per second
A measure of the bandwidth on a data transmission medium. One kbps equals
1000 bps.
lambda
See wavelength.
LAN
local area network
A data communications network that is geographically limited (typically to a
1 km radius), allowing easy interconnection of terminals, microprocessors,
and computers within adjacent buildings. Most notable of LAN topologies are
Ethernet, token ring, and FDDI.
laser
An acronym for "Light Amplification by Stimulated Emission of Radiation".
A laser is a monochromatic (same wavelength), coherent (waves in phase),
beam of radiation.
loss
The ratio of optical output power to input power, usually given in units of dB.
Usually represents a decrease in an optical signal. A negative loss means a
gain of power.
loss/attenuation
In an optical fiber, the absorption of light by molecules in the fiber, causing
some of the intensity of light to be lost from the signal. Usually measured in
dB.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
60 Glossary
loss budget
The amount of optical power launched into a system that will be lost through
various mechanisms, such as insertion losses and fiber attenuation. Usually
given in dB.
MAN
metropolitan area network
A MAN consists of LANs interconnected within a radius of approximately
80 km (50 miles). MANs typically use fiber-optic cable to connect LANs.
margin
The amount of loss, beyond the link budget amount, that can be tolerated in a
link.
MMF
multimode fiber
A fiber with core diameter much larger than the wavelength of light
transmitted that allows many modes of light to propagate. Commonly used
with LED sources for lower speed, short distance lengths. Typical core sizes
(measured in microns) are 50/125, 62.5/125 and 100/140.
mode
An independent light path through an optical fiber. See SMF and MMF.
multimode fiber
See MMF.
multiplexing
Carriage of multiple channels over a single transmission medium; any process
by which a dedicated circuit can be shared by multiple users. Typically, data
streams are interspersed on a bit or byte basis (time division), or separated by
different carrier frequencies (frequency division).
MUX
multiplexer
A device that combines two or more signals into a signal composite data
stream for transmission on a single channel.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary 61
NDSF
non-dispersion-shifted fiber
A type of optical fiber optimized for the 1310 nm transmission window.
nanometer
See nm.
nm
nanometer
One billionth of a meter (10-9 meter). A unit of measure commonly used to
express the wavelengths of light.
node
A point in an optical network where optical signals can be processed and
switched among various links.
NZDSF
non-zero-dispersion-shifted fiber
A type of optical fiber optimized for high bit-rate and dense
wavelength-division-multiplexing applications.
OADM
optical add/drop multiplexer
An optical multiplexer/demultiplexer (mux/demux) that adds or drops one
CWDM channel of the same wavelength from the optical fiber and allows all
other wavelengths to pass straight through.
O/E
OC
optical to electrical
Optical to electrical conversion.
optical carrier
Series of physical protocols, such as OC-1, OC-2, and OC-3, defined for
SONET optical signal transmissions. OC signal levels put STS frames onto
fiber-optic line at a variety of speeds. The base rate is 51.84 Mbit/s (OC-1);
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
62 Glossary
each signal level thereafter operates at a speed divisible by that number. For
example, OC-3 operates at 155.52 Mbit/s.
OC-1
optical carrier - level 1
An optical SONET signal at 51.84 Mbit/s.
OC-3
optical carrier - level 3
An optical SONET signal at 155.52 Mbit/s.
OC-12
optical carrier - level 12
An optical SONET signal at 622.08 Mbit/s.
OMUX
optical multiplexer
An optical multiplexer/demultiplexer that multiplexes and demultiplexes four
or eight CWDM wavelength channels from a two-fiber circuit.
optical channel
An optical wavelength band for WDM optical communications.
optical fiber
Very thin strands of pure silica glass through which laser light travels in an
optical network. Consists of a core surrounded by a less refractive index
cladding.
optical seam
An optical seam occurs at any site in a network when there is no optical
passthrough, that is, where information is dropped from but not added onto
the ring.
Optical Time Domain Reflectometer (OTDR)
Device used to inspect optical fiber links by sending optical pulses down them
and monitoring the light reflected back to the device. Can calculate overall
fiber attenuation and highlight points of loss in the fiber, or even fiber breaks.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary 63
optical waveguide
See optical fiber.
passive device
A device that does not require a source of energy to function.
passthrough
A signal bypass mechanism that allows the signal to pass through a device
with little or no signal processing.
point-to-point transmission
Carrying a signal between two endpoints without branching to other points.
protocol
The procedure used to control the orderly exchange of information between
stations on a data link or on a data-communications network or system.
Protocols specify standards in three areas: the code set, usually ASCII or
EBCDIC; the transmission mode, usually asynchronous or synchronous; and
the non-data exchanges of information by which the two devices establish
contact and control, detect failures or errors, and initiate corrective action.
provisioning
The process by which a requested service is designed, implemented, and
tracked.
ring architecture
A network topology in which terminals are connected serially point-to-point
in an unbroken circle.
Rx
receive
A terminal device that includes a detector and signal processing electronics. It
functions as an optical-to-electrical converter.
scalable
The ability to add power and capability to an existing system without
significant expense or overhead.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
64 Glossary
single-mode fiber
See SMF.
SMF
A mode is one of the various light waves that can be transmitted in an optical
fiber. Each optical signal generates many different modes, but in single-mode
fiber the aim is to only have one of them transmitted. This is achieved through
having a core of a very small diameter (usually around 10 micrometers), with
a cladding that is usually ten times the core diameter. These fibers have a
potential bandwidth of 50 to 100 GHz per kilometer.
Tx
transmit
A device that includes a LED or laser source and signal conditioning
electronics that is used to inject a signal into optical fiber.
U
(vertical) unit
One U is 1.75 inches. Standard equipment racks have bolt holes spaced
evenly on the mounting rails to permit equipment that is sized in multiples of
this vertical unit to be mounted in the same rack.
WAN
wide area network
A physical or logical network that provides data communications to a larger
number of independent users than are usually served by a LAN and is usually
spread over a larger geographic area than that of a LAN.
wavelength
All electromagnetic radiation (radio waves, microwaves, ultraviolet light,
visible light, etc.) is transmitted in waves, and the wavelength is the distance
between the successive crests of the waves. In optical networks, you can think
of different wavelengths as being different colors of light. Wavelengths of
light are measured in nanometers or microns.
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary 65
WDM
wavelength division multiplexing
Transmitting many different colors (wavelengths) of laser light down the
same optical fiber at the same time in order to increase the amount of
information that can be transferred.
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
66 Glossary
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
67
Index
A
add/drop mux
four-channel mux/demux 22
connecting cables 39
description 19
ring application 20
CWDM OADM
application
cabling 39
description 19
point-to-point, mux/demux 23
ring, add/drop mux 20
ring, mux/demux 24
attenuation 27
CWDM OMUX
B
cabling eight-channel 42
cabling four-channel 41
description 21
block diagram, connections
add/drop mux 20
C
cabling, specification
mux/demux 47
directivity, specification
mux/demux 47
SC, FC connectors 51
tools and materials 50
E
electrostatic discharge 36
connecting cables
add/drop mux 39
eight-channel mux/demux 42
four-channel mux/demux 41
environment, specification
add/drop mux 45
mux/demux 47
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
68 Index
equipment side connections
M
mesh ring application
eight-channel mux/demux 42
calculating transmission distance for 30
F
FC connectors, cleaning 51
fiber optic cable
attenuation and transmission 27
cleaning connectors for 50
precautions with 49
connecting cables, eight-channel 42
connecting cables, four-channel 41
description 21
front panel
add/drop mux 20
four-channel mux/demux 22
N
G
network backbone connections
add/drop mux 39
H
hub and spoke
I
insertion loss, specification
add/drop mux 45
mux/demux 47
isolation, specification
mux/demux 47
specifications 47
L
link budget
about 27
hub and spoke example 33
mesh ring example 30
point-to-point example 29
optical link budget
about 27
hub and spoke 33
mesh ring 30
point-to-point 29
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
optical routing system
description 17
transmission distance
about 27
shelf, installing 37
hub and spoke example 33
P
passband, specification
wavelength
add/drop mux 45
add/drop mux 45
mux/demux 47
usage specification
add/drop mux 45
mux/demux 47
point-to-point application
mux/demux 23
network configuration example 29
product support 15
publications
R
receptacle devices, cleaning 53
ring application
add/drop mux 20
mux/demux 24
S
shelf, optical
insert mux in 38
T
technical publications 14
technical support 15
tranceiver, CWDM GBIC 18
Installation and Networking Guidelines for Optical Routing
Download from Www.Somanuals.com. All Manuals Search And Download.
70 Index
212257-B
Download from Www.Somanuals.com. All Manuals Search And Download.
|