Part No. 303127-D Rev 00
December 2000
600 Technology Park Drive
Billerica, MA 01821-4130
V.34 Modem Adapter Module
Supplement
Download from Www.Somanuals.com. All Manuals Search And Download.
Japan/Nippon Requirements Only
Voluntary Control Council for Interference (VCCI) Statement
Taiwan Requirements
Bureau of Standards, Metrology and Inspection (BSMI) Statement
Canada Requirements Only
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (V.34 Modem Adapter Module) does not exceed the Class A limits for radio-noise emissions
from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (V.34 Modem Adapter Module) respecte les limites de bruits radioélectriques visant les
appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des
Communications du Canada.
Canada CS-03 Rules and Regulations
Notice: The Industry Canada label identifies certified equipment. This certification means that the equipment meets
telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal
Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to
the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed using an acceptable method of connection. The
customer should be aware that compliance with the above conditions may not prevent the degradation of service in
some situations.
303127-D Rev 00
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Canada Requirements Only (continued)
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or
alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines
and internal metallic water pipe system, if present, are connected together. This precaution may be particularly
important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric
inspection authority, or electrician, as appropriate.
Notice: For equipment using loopstart lines, please note that the Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of devices subject only to the requirement
that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. The REN is located on the “FCC
Rules Part 68” label located on the bracket of the module, or on the back of the unit.
Canada CS-03 -- Règles et règlements
Avis: L'étiquette d'Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est
conforme aux normes de protection, d'exploitation et de sécurité des réseaux de télécommunications, comme le
prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n'assure
toutefois pas que le matériel fonctionnera à la satisfaction de l'utilisateur.
Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le raccorder aux installations de l'entreprise
locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de
raccordement. L'abonné ne doit pas oublier qu'il est possible que la conformité aux conditions énoncées ci-dessus
n'empêche pas la dégradation du service dans certaines situations.
Les réparations de matériel homologué doivent être coordonnées par un représentant désigné par le fournisseur.
L'entreprise de télécommunications peut demander à l'utilisateur de débrancher un appareil à la suite de réparations ou
de modifications effectuées par l'utilisateur ou à cause de mauvais fonctionnement.
Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise à la terre de la source d'énergie électrique,
des lignes téléphoniques et des canalisations d'eau métalliques, s'il y en a, sont raccordés ensemble. Cette précaution
est particulièrement importante dans les régions rurales.
Avertissement: L'utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à un service
d'inspection des installations électriques, ou à un électricien, selon le cas.
Avis: Veuillez prendre note que pour tout appareillage supportant des lignes de type “loopstart,” l'indice d'équivalence
de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être
raccordés à une interface. La terminaison d'une interface téléphonique peut consister en une combinaison de quelques
dispositifs, à la seule condition que la somme d'indices d'équivalence de la sonnerie de tous les dispositifs n'excède pas
5. Le REN figure sur l’étiquette “FCC Rules Part 68” située sur le support du module ou à l’arrière de l’unité.
iv
303127-D Rev 00
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Part 68 Compliance Statement
This equipment complies with Part 68 of FCC Rules. All direct connections to telephone network lines must be made
using standard plugs and jacks compliant with FCC Part 68. Please note the following:
1. You are required to request service from the telephone company before you connect the unit to a network. When
you request service, you must provide the telephone company with the following data:
•
When you request T1 Service, you must provide the telephone company with
-- The Facility Interface Code
Provide the telephone company with all the codes below:
-
-
-
-
-
04DU9-BN (1.544 MB, D4 framing format)
04DU9-DN (1.544 MB, D4 framing format with B8ZF coding)
04DU9-1KN (1.544 MB, ESF framing format)
04DU9-1SN (1.544 MB, ESF framing format with B8ZF coding)
04DU9-1ZN (1.544 MB, ANSI ESF and ZBTSI without line power)
The telephone company will select the code it has available.
-- The Service Order Code(s) (SOC): 6.0F
-- The required Universal Service Order Code (USOC) jack: RJ48C
When you request Primary Rate ISDN Service, you must provide the telephone company with
-- The Facility Interface Code: 04DU9-1SN (1.544 MB, ESF framing format with B8ZF coding)
-- The Service Order Code(s) (SOC): 6.0F
•
-- The required Universal Service Order Code (USOC) jack: RJ48C
2. Your telephone company may make changes to its facilities, equipment, operations, or procedures that could
affect the proper functioning of your equipment. The telephone company will notify you in advance of such
changes to give you an opportunity to maintain uninterrupted telephone service.
3. If the unit causes harm to the telephone network, the telephone company may temporarily discontinue your
service. If possible, they will notify you in advance, but if advance notice is not practical, you will be notified
as soon as possible and will be informed of your right to file a complaint with the FCC.
4. If you experience trouble with the unit, please contact the Nortel Networks Technical Solutions Center in
your area for service or repairs. Repairs should be performed only by service personnel authorized by
Nortel Networks.
United States
1-800-2LANWAN
33-4-92-96-69-68
61-2-9927-8800
81-3-5740-1700
Valbonne, France
Sydney, Australia
Tokyo, Japan
5. You are required to notify the telephone company when you disconnect the unit from the network.
303127-D Rev 00
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Nortel Networks NA Inc. Software License Agreement
NOTICE: Please carefully read this license agreement before copying or using the accompanying software or
installing the hardware unit with pre-enabled software (each of which is referred to as “Software” in this Agreement).
BY COPYING OR USING THE SOFTWARE, YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF
THIS LICENSE AGREEMENT. THE TERMS EXPRESSED IN THIS AGREEMENT ARE THE ONLY TERMS
UNDER WHICH NORTEL NETWORKS WILL PERMIT YOU TO USE THE SOFTWARE. If you do not accept
these terms and conditions, return the product, unused and in the original shipping container, within 30 days of
purchase to obtain a credit for the full purchase price.
1. License grant. Nortel Networks NA Inc. (“Nortel Networks”) grants the end user of the Software (“Licensee”) a
personal, nonexclusive, nontransferable license: a) to use the Software either on a single computer or, if applicable, on
a single authorized device identified by host ID, for which it was originally acquired; b) to copy the Software solely
for backup purposes in support of authorized use of the Software; and c) to use and copy the associated user manual
solely in support of authorized use of the Software by Licensee. This license applies to the Software only and does not
extend to Nortel Networks Agent software or other Nortel Networks software products. Nortel Networks Agent
software or other Nortel Networks software products are licensed for use under the terms of the applicable Nortel
Networks NA Inc. Software License Agreement that accompanies such software and upon payment by the end user of
the applicable license fees for such software.
2. Restrictions on use; reservation of rights. The Software and user manuals are protected under copyright laws.
Nortel Networks and/or its licensors retain all title and ownership in both the Software and user manuals, including
any revisions made by Nortel Networks or its licensors. The copyright notice must be reproduced and included with
any copy of any portion of the Software or user manuals. Licensee may not modify, translate, decompile, disassemble,
use for any competitive analysis, reverse engineer, distribute, or create derivative works from the Software or user
manuals or any copy, in whole or in part. Except as expressly provided in this Agreement, Licensee may not copy or
transfer the Software or user manuals, in whole or in part. The Software and user manuals embody Nortel Networks’
and its licensors’ confidential and proprietary intellectual property. Licensee shall not sublicense, assign, or otherwise
disclose to any third party the Software, or any information about the operation, design, performance, or
implementation of the Software and user manuals that is confidential to Nortel Networks and its licensors; however,
Licensee may grant permission to its consultants, subcontractors, and agents to use the Software at Licensee’s facility,
provided they have agreed to use the Software only in accordance with the terms of this license.
3. Limited warranty. Nortel Networks warrants each item of Software, as delivered by Nortel Networks and properly
installed and operated on Nortel Networks hardware or other equipment it is originally licensed for, to function
substantially as described in its accompanying user manual during its warranty period, which begins on the date
Software is first shipped to Licensee. If any item of Software fails to so function during its warranty period, as the sole
remedy Nortel Networks will at its discretion provide a suitable fix, patch, or workaround for the problem that may be
included in a future Software release. Nortel Networks further warrants to Licensee that the media on which the
Software is provided will be free from defects in materials and workmanship under normal use for a period of 90 days
from the date Software is first shipped to Licensee. Nortel Networks will replace defective media at no charge if it is
returned to Nortel Networks during the warranty period along with proof of the date of shipment. This warranty does
not apply if the media has been damaged as a result of accident, misuse, or abuse. The Licensee assumes all
responsibility for selection of the Software to achieve Licensee’s intended results and for the installation, use, and
results obtained from the Software. Nortel Networks does not warrant a) that the functions contained in the software
will meet the Licensee’s requirements, b) that the Software will operate in the hardware or software combinations that
the Licensee may select, c) that the operation of the Software will be uninterrupted or error free, or d) that all defects
in the operation of the Software will be corrected. Nortel Networks is not obligated to remedy any Software defect that
cannot be reproduced with the latest Software release. These warranties do not apply to the Software if it has been
(i) altered, except by Nortel Networks or in accordance with its instructions; (ii) used in conjunction with another
vendor’s product, resulting in the defect; or (iii) damaged by improper environment, abuse, misuse, accident, or
negligence. THE FOREGOING WARRANTIES AND LIMITATIONS ARE EXCLUSIVE REMEDIES AND ARE
IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Licensee is responsible
vi
303127-D Rev 00
Download from Www.Somanuals.com. All Manuals Search And Download.
for the security of its own data and information and for maintaining adequate procedures apart from the Software to
reconstruct lost or altered files, data, or programs.
4. Limitation of liability. IN NO EVENT WILL NORTEL NETWORKS OR ITS LICENSORS BE LIABLE FOR
ANY COST OF SUBSTITUTE PROCUREMENT; SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES; OR ANY DAMAGES RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE OR
PROFITS ARISING OUT OF OR IN CONNECTION WITH THE PERFORMANCE OF THE SOFTWARE, EVEN
IF NORTEL NETWORKS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT
SHALL THE LIABILITY OF NORTEL NETWORKS RELATING TO THE SOFTWARE OR THIS AGREEMENT
EXCEED THE PRICE PAID TO NORTEL NETWORKS FOR THE SOFTWARE LICENSE.
5. Government licensees. This provision applies to all Software and documentation acquired directly or indirectly by
or on behalf of the United States Government. The Software and documentation are commercial products, licensed on
the open market at market prices, and were developed entirely at private expense and without the use of any U.S.
Government funds. The license to the U.S. Government is granted only with restricted rights, and use, duplication, or
disclosure by the U.S. Government is subject to the restrictions set forth in subparagraph (c)(1) of the Commercial
Computer Software––Restricted Rights clause of FAR 52.227-19 and the limitations set out in this license for civilian
agencies, and subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause of DFARS
252.227-7013, for agencies of the Department of Defense or their successors, whichever is applicable.
6. Use of software in the European Community. This provision applies to all Software acquired for use within the
European Community. If Licensee uses the Software within a country in the European Community, the Software
Directive enacted by the Council of European Communities Directive dated 14 May, 1991, will apply to the
examination of the Software to facilitate interoperability. Licensee agrees to notify Nortel Networks of any such
intended examination of the Software and may procure support and assistance from Nortel Networks.
7. Term and termination. This license is effective until terminated; however, all of the restrictions with respect to
Nortel Networks’ copyright in the Software and user manuals will cease being effective at the date of expiration of the
Nortel Networks copyright; those restrictions relating to use and disclosure of Nortel Networks’ confidential
information shall continue in effect. Licensee may terminate this license at any time. The license will automatically
terminate if Licensee fails to comply with any of the terms and conditions of the license. Upon termination for any
reason, Licensee will immediately destroy or return to Nortel Networks the Software, user manuals, and all copies.
Nortel Networks is not liable to Licensee for damages in any form solely by reason of the termination of this license.
8. Export and re-export. Licensee agrees not to export, directly or indirectly, the Software or related technical data or
information without first obtaining any required export licenses or other governmental approvals. Without limiting the
foregoing, Licensee, on behalf of itself and its subsidiaries and affiliates, agrees that it will not, without first obtaining
all export licenses and approvals required by the U.S. Government: (i) export, re-export, transfer, or divert any such
Software or technical data, or any direct product thereof, to any country to which such exports or re-exports are
restricted or embargoed under United States export control laws and regulations, or to any national or resident of such
restricted or embargoed countries; or (ii) provide the Software or related technical data or information to any military
end user or for any military end use, including the design, development, or production of any chemical, nuclear, or
biological weapons.
9. General. If any provision of this Agreement is held to be invalid or unenforceable by a court of competent
jurisdiction, the remainder of the provisions of this Agreement shall remain in full force and effect. This Agreement
will be governed by the laws of the state of California.
Should you have any questions concerning this Agreement, contact Nortel Networks, 4401 Great America Parkway,
P.O. Box 58185, Santa Clara, California 95054-8185.
LICENSEE ACKNOWLEDGES THAT LICENSEE HAS READ THIS AGREEMENT, UNDERSTANDS IT, AND
AGREES TO BE BOUND BY ITS TERMS AND CONDITIONS. LICENSEE FURTHER AGREES THAT THIS
AGREEMENT IS THE ENTIRE AND EXCLUSIVE AGREEMENT BETWEEN NORTEL NETWORKS AND
LICENSEE, WHICH SUPERSEDES ALL PRIOR ORAL AND WRITTEN AGREEMENTS AND
COMMUNICATIONS BETWEEN THE PARTIES PERTAINING TO THE SUBJECT MATTER OF THIS
AGREEMENT. NO DIFFERENT OR ADDITIONAL TERMS WILL BE ENFORCEABLE AGAINST
NORTEL NETWORKS UNLESS NORTEL NETWORKS GIVES ITS EXPRESS WRITTEN CONSENT,
INCLUDING AN EXPRESS WAIVER OF THE TERMS OF THIS AGREEMENT.
303127-D Rev 00
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preface
Before You Begin ............................................................................................................. xv
How to Use This Supplement .......................................................................................... xv
Acronyms .........................................................................................................................xvi
Hard-Copy Technical Manuals ........................................................................................xvii
How to Get Help .............................................................................................................xvii
Using the V.34 Modem Adapter Module in a Passport ARN Router
Attaching Cables ............................................................................................................1-1
Completing Software Configuration ................................................................................1-2
Interpreting LEDs ...........................................................................................................1-3
Using the V.34 Modem Adapter Module in a Passport 5430 Multiservice Access Switch
Attaching Cables ............................................................................................................2-4
Completing Software Configuration ................................................................................2-5
Interpreting LEDs ...........................................................................................................2-5
Chapter 3
Using the V.34 Modem Adapter Module in a Passport 2430 Multiservice Access Switch
Attaching Cables ............................................................................................................3-1
Completing Software Configuration ................................................................................3-2
Interpreting LEDs ...........................................................................................................3-2
303127-D Rev 00
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Figures
Figure 1-2. V.34 Modem Adapter Module LEDs .........................................................1-3
Figure 2-1. Passport 5430 V.34 Modem Adapter Module Connector .........................2-4
Figure 2-2. V.34 Modem Adapter Module LEDs .........................................................2-5
Figure 3-1. Passport 2430 V.34 Modem Adapter Module Connector .........................3-1
Figure 3-2. V.34 Modem Adapter Module LEDs .........................................................3-2
303127-D Rev 00
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
Table 1-1.
Table 1-2.
Table 2-1.
Table 2-2.
Table 3-1.
PROM Diagnostic and Boot Code for ARN Routers ................................1-1
V.34 Modem LEDs ...................................................................................1-3
Example WAN Adapter Module Combinations ........................................2-3
V.34 Modem LEDs ...................................................................................2-6
V.34 Modem LEDs ...................................................................................3-3
303127-D Rev 00
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
The V.34 Modem Adapter Module provides dial services capabilities at speeds
ranging from 1200 b/s to 115,200 b/s.
Before You Begin
This guide is intended for qualified service personnel who are installing the V.34
Modem Adapter Module in an Passport® ARN™, Passport 5430, or Passport 2430
for the first time or who need to install or replace any customer-replaceable unit
(CRU). A qualified service person should have appropriate technical training and
experience and be aware of the hazards involved in installing and replacing
CRUs.
How to Use This Supplement
the table below to find the chapter that contains the information appropriate for the
platform you are using.
Platform
Refer to
Passport ARN
Passport 5430
Passport 2430
Chapter 1
Chapter 2
Chapter 3
303127-D Rev 00
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
V.34 Modem Adapter Module Supplement
Text Conventions
This guide uses the following text conventions:
bold text
Indicates command names and options and text that
you need to enter.
Example: Enter show ip {alerts | routes}.
Example: Use the dinfo command.
italic text
Indicates file and directory names, new terms, book
titles, and variables in command syntax descriptions.
Where a variable is two or more words, the words are
connected by an underscore.
Example: If the command syntax is:
show at <valid_route>
valid_route is one variable and you substitute one value
for it.
Acronyms
This guide uses the following acronyms:
BRI
basic rate interface
CRU
DTR
ESD
customer-replaceable unit
data terminal ready
electrostatic discharge
ISDN
LED
Integrated Services Digital Network
light-emitting diode
PROM
RLSD
WAN
programmable read-only memory
received line signal detection
wide area network
xvi
303127-D Rev 00
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Hard-Copy Technical Manuals
You can print selected technical manuals and release notes free, directly from the
Internet. Go to the support.baynetworks.com/library/tpubs/ URL. Find the product
for which you need documentation. Then locate the specific category and model
or version for your hardware or software product. Use Adobe Acrobat Reader to
open the manuals and release notes, search for the sections you need, and print
download a free copy of Acrobat Reader.
You can purchase selected documentation sets, CDs, and technical publications
through the Internet at the www1.fatbrain.com/documentation/nortel/ URL.
How to Get Help
If you purchased a service contract for your Nortel Networks product from a
distributor or authorized reseller, contact the technical support staff for that
distributor or reseller for assistance.
If you purchased a Nortel Networks service program, contact one of the following
Nortel Networks Technical Solutions Centers:
Technical Solutions Center
Telephone
EMEA
(33) (4) 92-966-968
North America
Asia Pacific
China
(800) 2LANWAN or (800) 252-6926
(61) (2) 9927-8800
(800) 810-5000
An Express Routing Code (ERC) is available for many Nortel Networks products
and services. When you use an ERC, your call is routed to a technical support
person who specializes in supporting that product or service. To locate an ERC for
your product or service, go to the www12.nortelnetworks.com/ URL and click
ERC at the bottom of the page.
303127-D Rev 00
xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Using the V.34 Modem Adapter Module in a
Passport ARN Router
This chapter supplements Installing and Operating Passport ARN Routers
(Chapter 4, “Installing a WAN Adapter Module”). Follow the hardware
specific to the V.34 Modem adapter module.
Verifying ARN Router Requirements
Table 1-1 shows the minimum versions of boot and diagnostic programmable
read-only memory (PROM) code required for a V.34 Modem adapter module.
Table 1-1.
Code Type
PROM Diagnostic and Boot Code for ARN Routers
Minimum Version Directory
File Name
Boot
1.17
1.30
arn_proms
arn_proms
arnboot.exe
arndiag.exe
Diagnostic
For information on upgrading PROM code, see the BayRS™ Upgrading Routers
guide.
303127-D Rev 00
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
V.34 Modem Adapter Module Supplement
Attaching Cables
Connect the modem cable to the RJ-11 connector on the installed adapter module.
You install the V.34 Modem adapter module in one of the two front-panel WAN
adapter module slots (Figure 1-1). See Installing and Operating Passport ARN
Routers for complete installation instructions.
Front-panel V.34 modem interface
10BaseT
COM
Tx
Rx
Cl
1
RLSD
Serial
Eth
Telco
Tx
Rx
RLSD
DTR
10BaseT
V.34 Modem
Tx
Rx
Cl
To
RJ-11 telephone
receptacle
ARN0071A
Figure 1-1.
ARN V.34 Modem Adapter Module Connector (Slot 2)
1-2
303127-D Rev 00
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the V.34 Modem Adapter Module in a Passport ARN Router
Completing Software Configuration
Once you have successfully installed the V.34 Modem adapter module, complete
the following software configuration tasks using instructions found in your BayRS
documentation:
Configuration Task
Location of Instructions
Connect the ARN to the network.
One of the following:
•
Installing and Operating Passport ARN
Routers
•
Configuring Remote Access for AN and
Passport ARN Routers
Modify the ARN configuration file to add the Any of the following:
V.34 Modem adapter module and enable
default software services.
•
Configuring and Managing Routers with
Site Manager
•
Using the Bay Command Console
(BCC)
When using Bay Command Console
(BCC™) commands on an ARN router, note
that the name for the V.34 Modem adapter
module is arnv34.
Configure V.34 modem services.
Configuring Dial Services
For the latest information, be sure to review the release notes and documentation
Interpreting LEDs
The V.34 modem adapter module has four LEDs, located to the right of the
connector (Figure 1-2).
Telco
TX
RX
RLSD
DTR
V.34 Modem
Complies with FCC Rules Part 68 Reg. Number 4P8USA-30661-MD-E Ringer Equivalence 0.6B
ARN0107A
Figure 1-2.
V.34 Modem Adapter Module LEDs
303127-D Rev 00
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
V.34 Modem Adapter Module Supplement
Table 1-2 describes the V.34 Modem adapter module LEDs.
Table 1-2.
V.34 Modem LEDs
Meaning
LED
TX (Transmit)
Lights when the V.34 modem interface transmits data over the
network.
RX (Receive)
Lights when the V.34 modem interface receives data from the
network.
RLSD (Received Line Lights when the modem activates.
Signal Detection)
DTR (Data Terminal
Ready)
Lights when the V.34 modem interface is ready to transmit data.
Note: Adapter module LEDs blink on and off during diagnostic testing, but
the new V.34 Modem LEDs do not indicate data transfer until you have
configured and enabled the software services.
1-4
303127-D Rev 00
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Using the V.34 Modem Adapter Module in a
Passport 5430 Multiservice Access Switch
This chapter supplements Installing and Operating the Passport 5430
Multiservice Access Switch. Follow the hardware installation steps in that manual,
then refer to this document for information specific to the V.34 Modem adapter
module.
WAN Adapter Module Placement Considerations
When installing WAN adapter modules in the Passport 5430 Module slots, note
the following:
•
Each WAN adapter module you install is automatically assigned a circuit,
even if the WAN adapter module has not been configured. This prevents
disruption of active circuits if you reconfigure the the module at a later time.
•
ISDN BRI adapter modules can use two circuits (one for each of the 2 B
channels).
•
•
You can configure a total of 4 circuits.
Circuit allocations are prioritized according to which Module slot is being
used by the WAN adapter modules. Module slot 3 has priority over Module
slot 4, and Module slot 4 has priority over Module slot 5.
•
When there are more than the 4 possible circuits to be configured, for example
if there are 2 ISDN BRI adapter modules and a serial adapter module (5
circuits in all), circuit allocation becomes an issue.
303127-D Rev 00
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
V.34 Modem Adapter Module Supplement
In the example above, the first ISDN BRI module (in Module slot 3) has the
resources to bring up a second B channel (thus using 2 circuits). The serial adapter
in Module slot 4 uses a third circuit. The second ISDN BRI adapter module (in
Module slot 5), can have only 1 B channel configured because the serial adapter
Module slot 5. In this case, there are not enough circuits left to utilize the second
B channel on the ISDN BRI adapter in Module slot 5. In this example, if you
wanted to have both B channels on both ISDN BRI adapters configured, you
would have to remove the serial card from Module slot 4.
Table 2-1 lists examples of valid WAN adapter module combinations.
2-2
303127-D Rev 00
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the V.34 Modem Adapter Module in a Passport 5430 Multiservice Access Switch
Table 2-1.
Example WAN Adapter Module Combinations
Module 3
Module 4
Module 5
T1/FT1 or E1/FE1
T1/FT1 or E1/FE1
T1/FT1 or E1/FE1
T1/FT1 or E1/FE1
T1/FT1 or E1/FE1
T1/FT1 or E1/FE1
Serial or V.34 modem
T1/FT1 or E1/FE1
T1/FT1 or E1/FE1
Serial or V.34 modem
Serial or V.34 modem
ISDN 2 B-channels plus 1
D-channel
T1/FT1 or E1/FE1
T1/FT1 or E1/FE1
ISDN BRI 1 B-channel plus 1 Serial or V.34 modem
D-channel
Serial or V.34 modem
Serial or V.34 modem
Serial or V.34 modem
Serial or V.34 modem Serial or V.34 modem
Serial or V.34 modem Serial or V.34 modem
ISDN BRI 1 B-channel plus 1
D-channel
Serial or V.34 modem Serial or V.34 modem
ISDN BRI 2 B-channels plus 1
D-channel
Serial or V.34 modem ISDN BRI 2 B-channels plus 1 ISDN BRI 1 B-channel plus 1
D-channel D-channel
ISDN BRI
2 B-channels plus
1 D-channel
ISDN BRI 2 B-channels plus 1 Empty
D-channel
ISDN BRI
2 B-channels plus
1 D-channel
ISDN BRI 1 B-channel plus 1 Serial or V.34 modem
D-channel
ISDN BRI
2 B-channels plus
1 D-channel
ISDN BRI 1 B-channel plus 1 T1/FT1 or E1/FE1
D-channel
ISDN BRI
2 B-channels plus
1 D-channel
Serial or V.34 modem
T1/FT1 or E1/FE1
ISDN BRI 1 B-channel plus 1
D-channel
ISDN BRI
2 B-channels plus
1 D-channel
ISDN BRI 1 B-channel plus 1
D-channel
303127-D Rev 00
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
V.34 Modem Adapter Module Supplement
Attaching Cables
Connect the modem cable to the RJ-11 connector on the installed adapter module.
You may install the V.34 Modem adapter module in the front-panel Remote
Console slot (Figure 2-1), or in any of the three front-panel Module slots. See
Installing and Operating the Passport 5430 Multiservice Access Switch for the
complete installation procedure.
U
Module 3
ISDN BRI
with NT1
COM
Module 4
Module 5
Telco
Rem
V.34 Modem
Con
To
RJ-11 telephone receptacle
FBR0065A
Figure 2-1.
Passport 5430 V.34 Modem Adapter Module Connector
2-4
303127-D Rev 00
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the V.34 Modem Adapter Module in a Passport 5430 Multiservice Access Switch
Completing Software Configuration
Once you have successfully installed the V.34 Modem adapter module, complete
the following software configuration tasks using instructions found in your BayRS
documentation:
Configuration Task
Location of Instructions
Modify the Passport 5430 configuration file One of the following:
to add the V.34 Modem adapter module and
enable default software services.
•
•
Configuring and Managing Routers with
Site Manager
Using the Bay Command Console
(BCC)
When using Bay Command Console (BCC)
commands on a Passport 5430 router, note
that the name for the V.34 Modem adapter
module is arnv34.
Configure V.34 modem services.
Configuring Dial Services
For the latest information, be sure to review the release notes and documentation
Interpreting LEDs
The V.34 modem adapter module has four LEDs, located to the right of the
connector (Figure 2-2).
Telco
TX
RX
RLSD
DTR
V.34 Modem
Complies with FCC Rules Part 68 Reg. Number 4P8USA-30661-MD-E Ringer Equivalence 0.6B
ARN0107A
Figure 2-2.
V.34 Modem Adapter Module LEDs
303127-D Rev 00
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
V.34 Modem Adapter Module Supplement
Table 2-2 describes the V.34 Modem adapter module LEDs.
Table 2-2.
V.34 Modem LEDs
Meaning
LED
TX (Transmit)
Lights when the V.34 modem interface transmits data over the
network.
RX (Receive)
Lights when the V.34 modem interface receives data from the
network.
RLSD (Received Line Lights when the modem activates.
Signal Detection)
DTR (Data Terminal
Ready)
Lights when the V.34 modem interface is ready to transmit data.
Note: The V.34 modem adapter module LEDs blink on and off during
diagnostic testing, but the LEDs do not indicate data transfer until you have
configured and enabled the software services.
2-6
303127-D Rev 00
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Using the V.34 Modem Adapter Module in a
Passport 2430 Multiservice Access Switch
This chapter supplements the Installing and Operating the Passport 2430
Multiservice Access Switch. Follow the hardware installation steps in that manual,
then refer to this document for information specific to the V.34 Modem adapter
module.
Attaching Cables
Connect the modem cable to the RJ-11 connector on the installed adapter module.
You install the V.34 Modem adapter module in one of the two rear-panel WAN
adapter module slots (Figure 3-1). See Installing and Operating the Passport 2430
Multiservice Access Switch for the complete installation proecdure.
1
Telco
V.34 Modem
To
RJ-11 telephone
receptacle
VLK0024A
Figure 3-1.
Passport 2430 V.34 Modem Adapter Module Connector
303127-D Rev 00
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
V.34 Modem Adapter Module Supplement
Completing Software Configuration
Once you have successfully installed the V.34 Modem adapter module, complete
the following software configuration tasks using instructions found in your BayRS
documentation:
Configuration Task
Location of Instructions
Modify the configuration file to add the V.34 Any of the following:
Modem adapter module and enable default
software services.
•
•
Configuring and Managing Routers with
Site Manager
Using the Bay Command Console
(BCC)
When using Bay Command Console (BCC)
commands on a Passport 2430, note that
the name for the V.34 Modem adapter
module is arnv34.
Connect the Passport 2430 to the network. One of the following:
•
Installing and Operating the Passport
2430 Multiservice Access Switch
Configuring Remote Access for AN and
Passport ARN Routers
•
Configure V.34 modem services.
Configuring Dial Services
For the latest information, be sure to review the release notes and documentation
change notice for your version of BayRS software.
Interpreting LEDs
The V.34 modem adapter has four LEDs, located to the right of the connector
(Figure 3-2).
Telco
TX
RX
RLSD
DTR
V.34 Modem
Complies with FCC Rules Part 68 Reg. Number 4P8USA-30661-MD-E Ringer Equivalence 0.6B
ARN0107A
Figure 3-2.
V.34 Modem Adapter Module LEDs
3-2
303127-D Rev 00
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the V.34 Modem Adapter Module in a Passport 2430 Multiservice Access Switch
Table 3-1 describes the V.34 Modem adapter module LEDs.
Table 3-1.
V.34 Modem LEDs
Meaning
LED
TX (Transmit)
Lights when the V.34 modem interface transmits data over the
network.
RX (Receive)
Lights when the V.34 modem interface receives data from the
network.
RLSD (Received Line Lights when the modem activates.
Signal Detection)
DTR (Data Terminal
Ready)
Lights when the V.34 modem interface is ready to transmit data.
Note: Adapter module LEDs blink on and off during diagnostic testing, but
the new V.34 Modem LEDs do not indicate data transfer until you have
configured and enabled the software services.
303127-D Rev 00
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|