Patent Pending
Model No. NTL1495.2
Serial No.
USER'S MANUAL
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-825-2588
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
13. Keep the power cord and the surge suppres-
sor away from heated surfaces.
protect the floor or carpet from damage, place 14. Never move the walking belt while the power
a mat under the treadmill.
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. The treadmill should not be used by persons
weighing more than 350 pounds.
17. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. Never leave the treadmill unattended while it
is running. Always remove the key, unplug the
power cord, and switch the reset/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 5 for
the location of the reset/off circuit breaker.)
10. When connecting the power cord (see page 11),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 28.) You
must be able to safely lift 55 pounds (25 kg) to
raise, lower, or move the treadmill.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 11. To purchase a surge suppressor, see
your local NordicTrack dealer or call 1-888-
825-2588 and order part number 146148, or
see your local electronics store.
20. Do not change the incline of the treadmill by
placing objects under the treadmill.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
22. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or in-
cline changes. In some instances, the speed
and/or incline may change before the per-
sonal trainer describes the change.
25. Inspect and properly tighten all parts of the
treadmill regularly.
26. Never insert or drop any object into any
opening.
27.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
23. When using iFIT.com CDs and videos, you
can manually override the speed and incline
settings by pressing the speed and incline
buttons. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
24. Always remove iFIT.com CDs and videos from
your CD player or VCR and disconnect your
MP3 player when you are not using them.
28. The treadmill is intended for in-home use
only. Do not use the treadmill in any commer-
cial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on your treadmill. If a decal is missing or
illegible, please call the toll-free telephone number on the front cover of this manual
and order a free replacement decal. Apply the decal in the location shown. Note: The
decals may not be shown at actual size.
KEEP HANDS
AND FEET
AWAY FROM
THIS AREA
WHILE THE
TREADMILL IS
IN OPERATION.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the revolutionary NordicTrack®
C2420 treadmill. The C2420 treadmill offers a selec-
tion of features designed to make your workouts at
home more enjoyable and effective. And when you’re
not exercising, the unique C2420 treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
ing this manual, see the front cover of this manual. To
help us assist you, please note the product model
number and serial number before calling. The model
number of the treadmill is NTL1495.2. The serial num-
ber can be found on a decal attached to the treadmill
(see the front cover of this manual for the location).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Book Holder
Fan
Console
Accessory Tray
Handrail
Pulse Sensor
Key/Clip
Latch Knob
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Rear Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included allen wrench
and your own phillips screwdriver
and
wire cutters . For help identifying the assembly hardware, see the hardware drawings below.
3/4” Tek Screw (44)–4
1” Tek Screw (82)–2
Short Console
Bolt (112)–2
Star Washer (67)–12
3/4” Screw (7)–2
Extension Screw
(87)–4
Handrail Bolt (66)–4
Pulse Bar Bolt (127)–4
Console Bolt (72)–2
1. Open parts bag A. With the help of a second person,
carefully raise the Uprights (85) and the Frame (55) to
the position shown.
1
85
While the other person holds the Uprights (85) and the
Frame (55), slide the two Base Extensions (90) onto the
two brackets on the base of the Uprights. Make sure
that the Base Extensions are turned so the Base Pads
(81) are beneath it. Note: It may be helpful to tip the
Uprights forward as you insert the Base Extensions.
55
Brackets
90
90
81
81
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. With the help of a second person, carefully tip the Frame
(55) and the Uprights (85) down to the position shown.
Make sure that the Base Extensions (90) remains in
place.
2
3
4
92
55
44
Carefully slide the Base Cover (92) onto the base of the
Uprights (85). Attach the Base Cover with four 3/4” Tek
Screws (44); start all four Tek Screws before tighten-
ing them. Be careful not to overtighten the Tek
Screws.
90
85
90
3. Attach the Base Extensions (90) with four Extension
Screws (87); start all four Extension Screws before
tightening them.
83
82
Attach the two Thin Base Pads (83) to the base of the
Uprights (85) in the locations shown with two 1” Tek
Screws (82).
87
Note: Replacement Base Pads may be included. Use the
Base Pads to replace any that becomes worn.
90
85
87
With the help of a second person, carefully tip the
Uprights (85) back to the vertical position.
83
90
82
4. With the help of a second person, raise the Frame (55) to
the vertical position.
55
While the other person holds the Frame (55), press the
smaller end of the Shock (86) onto the bracket on the base
of the Uprights (85). Make sure to orient the Shock as
shown. Press the other end of the Shock onto the bracket
on the Frame. Note: It may be necessary to tip the Frame
forward or back to attach the Shock. Do not tip the Frame
forward past the vertical position.
86
Carefully lower the Frame (55) to the floor.
85
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Cut the tie securing the Pulse Wire (74) to the right
Upright (85). Hold the Pulse Bar Assembly (69) near the
crossbar on the Uprights. Connect the Pulse Wire to the
wire in the Pulse Bar Assembly. The connectors should
slide together easily and snap into place. If they do
not, turn one connector and try again. Insert the wires
into the crossbar.
5
6
7
127
67
Crossbar
67
127
Open parts bag B. Attach the Pulse Bar Assembly (69) to
the crossbar on the Uprights (85) with four Pulse Bar Bolts
(127) and Star Washers (67). Start all four Pulse Bar Bolts
before tightening them. Make sure that no wires are
pinched.
74
69
85
If you have purchased an optional chest pulse sensor,
follow step 6 to install the receiver included with the
chest pulse sensor. If you have not, go to step 7.
74
6. Place the console assembly face-down. Be careful not to
scratch the face of the console. Remove the indicated
3/4” Screw (7) and the Access Door (95) from the left side
of the Console Back (96).
7
95
Small
Cylinder
Connect the wire on the receiver (A) to the indicated wire
extending from the Console Back (96). Hold the receiver
so the small cylinder is oriented as shown and is fac-
ing the Console Back. Attach the receiver to the plastic
posts on the Access Door (95) with the two included small
screws.
96
A
Wire
Small
Screws
Make sure that no wires are pinched. Reattach the
Access Door (95) with the 3/4” Screw (7). Discard the
other wires included with the receiver.
7. Cut the tie securing the wires to the right Upright (85).
Have a second person hold the console assembly near the
Uprights. Connect the Upright Wire Harness (73) and the
Pulse Wire (74) to the wires extending from the console as-
sembly. The connectors should slide together easily
and snap into place. If they do not, turn one connector
and try again. Insert the connectors into the console as-
sembly. If necessary, remove the right accessory tray (not
shown) from the console assembly.
Console
Assembly
Ground
Wire
74
113
85
Connect the Upright Ground Wire (113) to the ground wire
extending from the console assembly. Make sure that the
wires are fully inserted into each other. Insert the ground
wires into the console assembly. Reinsert the right acces-
sory tray (not shown) into the console assembly if neces-
sary.
73
74
73
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Set the console assembly on the Uprights (85). Make sure
that no wires are pinched. Finger tighten a Console Bolt
(72) with a Star Washer (67) into the lower hole in each
Upright (only one side is shown).
8
71
Next, finger tighten a Short Console Bolt (112) with a
Star Washer (67) into the upper hole in each Upright (85)
(only one side is shown). Be careful not to drop the
Short Console Bolts into the Uprights. Firmly tighten
the two Console Bolts (72) and the two Short Console
Bolts.
85
67
112
67
72
Console
Assembly
Insert an Upright Endcap (71) into the top of each Upright
(85) (only one side is shown). Note: Insert the end of the
Upright Endcap indicated by the arrow first; use a rubber
mallet if necessary.
9. Slide the two Upright Covers (75) onto the ends of the
Handrails (68, 70). Align the holes in the lower ends of the
Handrails with the holes in the Uprights (85). Do not drop
the Handrails into the Uprights. Do not cut the indicated
black tie.
9
68
Loosely thread four Handrail Bolts (66) with four Star
Washers (67) into the Handrails (68, 70) and the Uprights
(85). Firmly tighten the four Handrail Bolts.
75
70
75
67
Do
Not
Cut
66
85
85
67
66
10. Press the right Upright Cover (75) onto the right Upright
(85). Attach the Upright Cover with a 3/4” Screw (7).
10
Repeat this step on the other side (not shown).
85
75
7
9
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Remove the knob from the pin. Make sure that the collar
and the spring are on the pin.
11
Press the Latch Insert (77) into the left Upright (85) as
shown. Use a rubber mallet if necessary. Insert the pin
through the Latch Insert. Tighten the knob back onto the
pin.
Knob
77
Spring
Collar
Pin
85
12. Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen
wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 31). To protect the
floor or carpet from damage, place a mat under the treadmill.
If you purchase the optional chest pulse sensor (see page 27) after the treadmill is assembled, follow the
steps below to install the receiver included with the chest pulse sensor.
1. Make sure that the power cord is unplugged. Follow
assemble steps 8 to 10 in reverse order (begin with step
10).
2. Lift the left side of the console assembly. Be careful not
to pull any wires. Remove the indicated 3/4” Screw (7)
and the Access Door (95) from the left side of the
Console Back (96).
3. Connect the wire on the receiver (A) to the indicated wire
Small
extending from the Console Back (96). Hold the re-
Screws
96
ceiver so the small cylinder is oriented as shown and
is facing the Console Back. Attach the receiver to the
plastic posts on the Access Door (95) with the two in-
cluded small screws.
Wire
A
95
Small
Cylinder
4. Make sure that no wires are pinched. Reattach the
Access Door (95) with the 3/4” Screw (7). Discard the
other wires included with the receiver.
7
5. Repeat assembly steps 8 to 10.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local NordicTrack dealer or call 1-888-825-
2588 and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: If there is a thin sheet of plastic
on the face of the console, remove it.
Key
Clip
FEATURES OF THE CONSOLE
you can connect the treadmill to your portable stereo,
home stereo, computer, or VCR and play special
iFIT.com MP3, CD, and video programs (iFIT.com MP3
programs, CDs, and videocassettes are available sepa-
rately). iFIT.com programs automatically control the
speed and incline of the treadmill as a personal trainer
guides you through every step of your workout; high-
energy music provides added motivation. To purchase
and download iFIT.com MP3 programs, go to
cassettes, call the toll-free telephone number on
the front cover of this manual.
The treadmill console offers an impressive array of
features designed to make your workouts more effec-
tive and enjoyable. When the manual mode of the con-
sole is selected, the speed and incline of the treadmill
can be changed with the touch of a button. As you ex-
ercise, the console will display continuous exercise
feedback. You can even measure your heart rate using
the built-in handgrip pulse sensor or the optional chest
pulse sensor (see page 27).
In addition, the console features ten preset programs
that automatically control the speed and incline of the
treadmill as they guide you through effective workouts.
You can even create your own custom workout pro-
grams and save them in memory for future use. The
console also offers four heart rate programs that control
the speed and incline of the treadmill to keep your heart
rate near a target heart rate during your workouts.
Note: You must wear the optional chest pulse sensor to
use the heart rate programs.
With the treadmill connected to your computer, you
programs directly from our Web site. See
To use the manual mode of the console, follow the
steps beginning on page 13. To use a preset
program, see page 16. To create and use a custom
program, see pages 18 and 19. To use a heart rate
program, see page 20. To use an iFIT.com MP3, CD,
or video program, see page 24. To use an iFIT.com
program directly from our Web site, see page 26.
The console also features iFIT.com interactive technol-
ogy. Having iFIT.com technology is like having a per-
sonal trainer in your home. Using a stereo audio cable,
12
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
Start the walking belt.
4
Plug in the power cord (see page 11).
To start the walking belt, press the Start button,
the Speed increase button, or one of the twelve
1-Step Speed buttons.
1
Locate the reset/off
circuit breaker near
the power cord. Make
sure that the circuit
breaker is in the reset
position.
2
If the Start button or the
Speed increase button
is pressed, the walking
belt will begin to move at
1 mph. As you exercise,
change the speed of the
On
Position
walking belt as desired by pressing the Speed in-
crease and decrease buttons. Each time a button
is pressed, the speed setting will change in incre-
ments of 0.1 mph; if a button is held down, the
speed setting will change in increments of 0.5
mph. Note: After the buttons are pressed, it may
take a moment for the walking belt to reach the se-
lected speed setting.
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing on page 12)
3
and attach the clip securely to the waistband of
your clothes. Next, insert the key into the console.
After a moment, the display will light. Note: When
the power is turned on, the program that was se-
lected the last time the Save button was pressed
will automatically be reselected. If the Save button
has not yet been pressed, the manual mode will
be selected.
If one of the 1-Step Speed buttons is pressed, the
walking belt will gradually increase in speed until it
reaches the selected speed setting.
Test the clip by carefully taking a few steps
backward until the key is pulled from the con-
sole. If the key is not pulled from the console,
adjust the position of the clip as needed.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the 1-Step Speed
buttons.
HOW TO USE THE MANUAL MODE
Change the incline of the treadmill as desired.
5
To change the incline of the treadmill, press the
Incline increase and decrease buttons or one of
the twelve 1-Step Incline buttons.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER above.
Each time the Incline in-
crease or decrease but-
ton is pressed, the incline
will change by 0.5%.
Designate yourself as user A, B, C, or D.
2
The console can save program settings for up to
four different users. To designate yourself as user
A, B, C, or D, press one of the Personal Setting
buttons labeled A, B, C, and D.
Note: After the buttons
are pressed, it may take a
moment for the treadmill to reach the selected in-
cline setting.
Select the manual mode.
3
If one of the 1-Step Incline buttons is pressed, the
incline will gradually increase until it reaches the
selected incline setting.
To select
the manual
mode, press
the
Programs
button re-
peatedly
Track
until a track appears in the center of the display.
Make sure that the word “Programs” does not ap-
pear below the track.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
The Time zone of the dis-
play will show the elapsed
time. Note: When a pro-
gram is selected, the dis-
play will show the time re-
maining in the program
instead of the elapsed time.
Adjust the cushioning system as desired.
6
The treadmill features a
cushioning system that
reduces the impact as
you walk or run on the
treadmill. There are fif-
teen firmness levels. To
increase the firmness of
the walking platform, turn
the Active Response
Cushioning knob coun-
The Heart Rate/Calories
zone of the display will
show the approximate
number of calories you
terclockwise. To decrease the firmness, turn the
knob clockwise. The display will show the se-
lected firmness level. If you wish to save the se-
lected firmness level, press the Save button. Note:
A clicking sound may be heard when the cushion-
ing system is being adjusted.
have burned. The dis-
play will also show your
heart rate when you use the handgrip pulse sensor
or the optional chest pulse sensor.
The Pace/Speed zone of
the display will show the
speed of the walking belt
and your pace (pace is
measured in minutes per
mile).
Follow your progress with the display.
7
When the
manual
mode or the
iFIT.com
Note: The console can
mode is se-
lected, the
display speed and dis-
tance in either miles or
Track
center of the
kilometers. To find which
display will show a 1/4-mile track. As you walk or
run, the indicators around the track will light in suc-
cession until the entire track is lit. The track will
then darken and the indicators will again begin to
light in succession.
unit of measurement is
selected, hold down the
Stop button while inserting the key into the con-
sole. An “E” for English miles or an “M” for metric
kilometers will appear in the Pace/Speed zone of
the display. Press the Speed increase button to
change the unit of measurement. When the de-
sired unit of measurement is selected, remove the
key and then reinsert it. Note: For simplicity, all
instructions in this section refer to miles.
The lower right zone of
the display will show a
training zone bar that in-
dicates the approximate
intensity level of your ex-
ercise. If eight indicators
in the bar are lit, for ex-
ample, the bar shows
that your pace is ideal for
aerobic exercise.
The Odometer zone of
the display will show the
distance that you have
walked or run during your
workout.
The Incline/Carbs zone
of the display will show
the incline level of the
treadmill and the approxi-
To see the total number of miles that the walking
belt has moved since the treadmill was purchased,
press the Odometer button; the words “Total Miles”
and the total number of miles will appear in the dis-
play.
mate number of grams of
carbs you have burned.
Note: Each time the incline changes, the display
will show the incline setting for a few seconds.
To see the total number of miles that the walking
belt has moved during a recent period of time,
such as the most recent month, press the
Odometer button again; the words “My Miles” and
the total number of miles will appear in the display.
To reset this number, hold down the Odometer
button for a few seconds.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
To again see the distance that you have walked or
run during your workout, press the Odometer but-
ton again.
the display. To turn on the fans at medium speed,
press the button a second time; the number 2 will
appear. To turn on the fans at high speed, press
the button a third time; the number 3 will appear.
To select the Auto mode, press the button again;
the word “Auto” will appear. When the auto mode
is selected, the speed of the fans will automati-
cally increase and decrease as the speed of the
walking belt increases and decreases.
To reset the display, press the Stop button, re-
move the key, and then reinsert the key.
Measure your heart rate if desired.
8
Note: If you
use the
To turn off the fans, press the AutoBreeze Fans
button again. Note: A few minutes after the walk-
ing belt is stopped, the fans will automatically turn
off.
handgrip
pulse sen-
sor and the
optional
chest pulse
sensor at
the same
time, the
When you are finished exercising, remove the
key.
10
Contacts
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage posi-
tion or the treadmill will be damaged. Next, re-
move the key from the console and put it in a se-
cure place. Note: If the display remains lit after
the key is removed, the console is in the
“demo” mode. See page 27 and turn off the
demo mode.
console will
not display your heart rate accurately. Before
using the handgrip pulse sensor, remove the clear
plastic film from the metal contacts. In addition,
make sure that your hands are clean.
To measure your heart rate, stand on the foot
rails and hold the metal contacts—avoid moving
your hands. When your pulse is detected, the
heart symbol in the Heart Rate/Calories zone of
the display will appear, one or two dashes will ap-
pear, and then your heart rate will be shown. For
the most accurate heart rate reading, continue
to hold the contacts for about 15 seconds.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the off
position and unplug the power cord.
Note: The first time the treadmill is used, observe
the alignment of the walking belt, and align the
walking belt if necessary (see page 31).
Turn on the fans if desired.
9
To turn on the fans at
low speed, press the
AutoBreeze Fans button;
the number 1 will appear
below the word “Fan” in
15
Download from Www.Somanuals.com. All Manuals Search And Download.
new speed settings of the program. If you wish to
save the new intensity level of the program for fu-
ture workouts, press the Save button.
HOW TO USE A PRESET PROGRAM
Insert the key into the console.
1
Press the Start button or the Speed increase
button to start the program.
5
See HOW TO TURN ON THE POWER on page
13.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Identify yourself as user A, B, C, or D.
2
See step 2 on page 13.
Each program is divided into several one-minute
segments. One speed setting and one incline set-
ting are programmed for each segment. Note: The
same speed setting and/or incline setting may be
programmed for two or more consecutive seg-
ments.
Select one of the preset programs.
3
To select
one of the
ten preset
programs,
press the
Programs
button re-
The speed
setting for
the first seg-
ment will be
shown in the
flashing
peatedly
until the
Current Segment
words “Weight Loss,” “Aerobic,” or “Performance”
and the number 1, 2, 3, or 4 appear in the lower
center of the display.
Current
Segment column of the matrix. (The incline set-
tings are not shown in the matrix.) The speed set-
tings for the next twelve segments will be shown
in the twelve columns to the right.
As each preset program is selected, the maximum
speed setting of the program and the maximum
incline setting of the program will flash in the dis-
play for a few seconds. The Time zone of the dis-
play will show how long the program will last. A
profile of the speed settings of the program will
scroll across the matrix in the center of the dis-
play.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or in-
cline of the treadmill is about to change, the speed
setting and/or incline setting will flash in the dis-
play to alert you.
Adjust the intensity level of the program if
desired.
4
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second seg-
ment. Note: If all seven of the indicators in the
Current Segment column are lit, the speed settings
may also move downward so that only the highest
indicators appear in the matrix.
The lower right zone of
the display will show the
intensity level of the se-
lected program; there
are fifteen intensity lev-
els. If desired, turn the
Program Intensity dial to
increase or decrease the
intensity level of the pro-
gram. If you change the
intensity level, the new
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
maximum speed setting of the program and the
new maximum incline setting of the program will
flash in the display for a few seconds. In addition,
the profile in the matrix will change to show the
16
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed and/or incline settings of the program
are too high or too low, you can change the inten-
sity level of the program at any time by turning the
Program Intensity dial. If you wish to save the new
intensity level of the program for future workouts,
press the Save button.
Measure your heart rate if desired.
See step 8 on page 15.
8
Turn on the fans if desired.
See step 9 on page 15.
9
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 1 mph. When the next segment
of the program begins, the treadmill will automati-
cally adjust to the speed and incline settings for the
next segment.
When you are finished exercising, remove the
key from the console.
10
When the program ends, make sure that the in-
cline of the treadmill is at the lowest setting.
Next, remove the key from the console and put it in
a safe place. Note: If the display remains lit
after the key is removed, the console is in the
“demo” mode. See page 27 and turn off the
demo mode.
Adjust the cushioning system as desired.
6
7
See step 6 on page 14.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the off
position and unplug the power cord.
Follow your progress with the display.
See step 7 on page 14.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Refer to the
matrix. Each
custom pro-
gram is di-
vided into
HOW TO CREATE A CUSTOM PROGRAM
Insert the key into the console.
1
Current Segment
one-minute
segments.
See HOW TO TURN ON THE POWER on page
13.
One speed setting and one incline setting can be
programmed for each segment. The speed setting
for the first segment will be shown in the flashing
Current Segment column of the matrix. (The in-
cline settings are not shown in the matrix.) To pro-
gram a speed setting and an incline setting for the
first segment, simply adjust the speed and incline
of the treadmill as desired by pressing the Speed
and Incline buttons. Every few times a Speed but-
ton is pressed, an additional indicator will appear
or disappear in the Current Segment column.
Identify yourself as user A, B, C, or D.
2
See step 2 on page 13.
Select one of the custom programs.
3
To select a
custom pro-
gram, press
the
Programs
button re-
peatedly
until the
When the first segment of the program ends, a se-
ries of tones will sound and the current speed set-
ting and the current incline setting will be saved in
memory. The three columns of indicators will then
move one column to the left, and the speed set-
ting for the second segment will be shown in the
flashing Current Segment column. Program a
speed setting and an incline setting for the second
segment as described above.
words “My
Design” and the number “1” or “2” appear in the
display.
Note: If the custom program has not yet been
defined, only three columns of indicators will
scroll across the matrix in the center of the
display. If more than three columns of indica-
tors appear, see HOW TO USE A CUSTOM
PROGRAM on page 19.
Continue programming speed and incline settings
for as many segments as desired; custom pro-
grams can have up to forty segments. When you
are finished with your workout, press the Stop but-
ton twice. The speed and incline settings that you
have programmed and the number of segments
that you have programmed will then be saved in
memory.
Press the Start button or the Speed increase
button and program the desired speed and in-
cline settings.
4
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
When you are finished exercising, remove the
key from the console.
5
See step 10 on page 17.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
The speed
setting for
the first seg-
ment will be
shown in the
flashing
HOW TO USE A CUSTOM PROGRAM
Insert the key into the console.
1
Current Segment
See HOW TO TURN ON THE POWER on page
13.
Current
Segment column of the matrix. (The incline set-
tings are not shown in the matrix.) The speed set-
tings for the next nine segments will be shown in
the columns to the right.
Identify yourself as user A, B, C, or D.
2
See step 2 on page 13.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or in-
cline of the treadmill is about to change, the
speed setting and/or incline setting will flash in the
display to alert you.
Select one of the custom programs.
3
To select a
custom pro-
gram, press
the
Programs
button re-
peatedly
until the
words “My
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second segment.
Design” and the number “1” or “2” will appear in
the display.
As each custom program is selected, the maxi-
mum speed setting of the program and the maxi-
mum incline setting of the program will flash in the
display for a few seconds. The Time zone of the
display will show how long the program will last. A
profile of the speed settings of the program will
scroll across the matrix in the center of the dis-
play. Note: If only three columns of indicators
scroll across the matrix, see HOW TO CREATE
A CUSTOM PROGRAM on page 18.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
If desired, you can redefine the program while
using it. To change the speed or incline setting
for the current segment, simply press the Speed
or Incline buttons. When the current segment ends,
the new setting will be saved in memory. To in-
crease the length of the program, first wait until
the program is completed. Then, press the Start but-
ton and program speed and incline settings for as
many additional segments as desired. When you
have added as many segments as desired, press
the Stop button twice. To decrease the length of
the program, press the Stop button twice at any
time before the program is completed.
Press the Start button or the Speed increase
button to start the program.
4
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings that you programmed previously.
Hold the handrails and begin walking.
Each custom program is divided into several one-
minute segments. One speed setting and one in-
cline setting are programmed for each segment.
Note: The same speed setting and/or incline set-
ting may be programmed for two or more consec-
utive segments.
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 1 mph. When the next segment
of the program begins, the treadmill will automati-
cally adjust to the speed and incline settings for the
next segment.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust the cushioning system as desired.
Select a heart rate program.
5
6
7
8
9
4
See step 6 on page 14.
To select a
heart rate
program,
press the
Programs
button re-
peatedly until
the words
Follow your progress with the display.
See step 7 on page 14.
Measure your heart rate if desired.
See step 8 on page 15.
“Heart Rate”
and the number 1, 2, 3, or 4 appear in the lower
center of the display.
Turn on the fans if desired.
See step 9 on page 15.
As each heart rate program is selected, a profile
of the target heart rate settings of the selected
program will scroll across the matrix in the center
of the display. Note: If heart rate program 4 is se-
lected, a heart beat symbol instead of a profile will
scroll across the matrix.
When you are finished exercising, remove the
key from the console.
See step 10 on page 17.
Enter a maximum target heart rate setting.
5
When a heart rate pro-
HOW TO USE A HEART RATE PROGRAM
gram is selected, the
words “Heart Rate” will
appear in the Heart
Rate/Calories zone of the
display and the maximum
CAUTION:
If you have heart prob-
lems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regu-
larly, consult your physician to find whether the
medication will affect your exercise heart rate.
target heart rate setting of the program will flash. If
desired, press the Heart Rate increase and de-
crease buttons to change the maximum target
heart rate setting. To save the new maximum tar-
get heart rate setting for future workouts, press
the Save button. Note: See the heart rate chart on
page 32 for heart rate guidelines.
Follow the steps below to use a heart rate program.
Press the Start button or the Speed increase
button to start the program.
6
Put on the optional chest pulse sensor.
1
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
You must wear the optional chest pulse sensor
(see page 27) to use a heart rate program.
Insert the key into the console.
2
Each heart rate program is divided into 20 one-
minute segments. One target heart rate setting is
programmed for each segment. Note: The same
target heart rate setting may be programmed for
two or more consecutive segments. If heart rate
program 4 is selected, the maximum target heart
rate setting is programmed for all segments.
See HOW TO TURN ON THE POWER on
page 13.
Identify yourself as user A, B, C, or D.
3
See step 2 on page 13.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
The target
heart rate
shown in the Current Segment column and the
last segment ends. The walking belt will then slow
to a stop.
setting for
the first seg-
ment will be
shown in the
flashing
Current Segment column of the matrix. The target
heart rate settings for the next twelve segments
will be shown in the columns to the right.
Current Segment
If the speed and/or incline settings of the program
are too high or too low, you can change the inten-
sity level of the program at any time by pressing
the Heart Rate increase and decrease buttons to
change the maximum target heart rate setting. If
you wish to save the new maximum target heart
rate setting for future workouts, press the Save
button.
If heart rate
program 4 is
selected, the
target heart
rate setting
will not be
shown in the
matrix. Instead, a heart beat symbol will scroll
across the matrix.
If your pulse is not detected during the program,
the letters “PLS” will flash in the Heart Rate/
Calories zone of the display and the speed and in-
cline of the treadmill may automatically decrease
until your pulse is detected. If this occurs, see the
instructions included with the optional chest pulse
sensor.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. In addition, the speed
setting and/or incline setting will flash in the dis-
play. When the first segment ends, all target heart
rate settings will move one column to the left. The
target heart rate setting for the second segment
will then be shown in the flashing Current
Segment column.
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 1 mph. When the console com-
pares your heart rate to the target heart rate, the
speed and/or incline of the treadmill will automati-
cally change to bring your heart rate closer to the
target heart rate.
Adjust the cushioning system as desired.
During each segment, the console will compare
your heart rate to the target heart rate setting. If
your heart rate is too far below or above the target
heart rate setting, the speed of the walking belt
will automatically increase or decrease to bring
your heart rate closer to the target heart rate set-
ting. If the speed reaches the maximum speed
setting of the program (7.5 mph) and your heart
rate is still too far below the target heart rate set-
ting, the incline of the treadmill will also increase
to bring your heart rate closer to the target heart
rate setting.
7
8
See step 6 on page 14.
Follow your progress with the displays.
See step 7 on page 14.
Turn on the fans if desired.
See step 9 on page 15.
9
When you are finished exercising, remove the
key.
10
The program will continue in this way until the tar-
get heart rate setting for the last segment is
See step 10 on page 17.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO USE
IFIT.COM PROGRAMS
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
1/8” LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com MP3 or CD programs, the treadmill
must be connected to your MP3 player, CD player,
portable stereo, home stereo, or computer. See pages
22 and 23 for connecting instructions. To use iFIT.com
programs directly from our Web site, the treadmill
must be connected to your computer. See page 23 for
connecting instructions. To use iFIT.com video pro-
grams, the treadmill must be connected to your VCR.
See page 24 for connecting instructions.
A. Plug one end of a long 1/8” to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into the AUDIO OUT jack on your stereo.
A/B
HOW TO CONNECT YOUR MP3 PLAYER OR CD
PLAYER
AUDIO OUT
LINE OUT
RIGHT
LEFT
A. Plug one end of the included 1/8” to 1/8” stereo
audio cable into the input jack on the console. Plug
the other end of the cable into a jack on your MP3
player or CD player. Plug your headphones into the
headphone jack on the console.
Audio Cable
A
B. See the drawing above. Plug one end of a long 1/8”
to 1/8” stereo audio cable (available at electronics
stores) into the input jack on the console. Plug the
other end of the cable into the LINE OUT jack on
your stereo. Note: While the cable is plugged into
the LINE OUT jack, do not plug your headphones
into the headphone jack on the console.
PHONES LINE OUT
LINE OUT
PHONES
Audio
Cable
C. Plug one end of a long 1/8” to 1/8” stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into the PHONES jack on your stereo. Plug your
headphones into the headphone jack on the console.
Headphones
C
PHONES
Audio
Cable
Headphones
22
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
A. Plug one end of a long 1/8” to 1/8” stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into the LINE OUT jack on your computer. Note:
While the cable is plugged into the LINE OUT jack,
do not plug your headphones into the headphone
jack on the console.
A. Plug one end of a long 1/8” to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into the LINE OUT jack on your stereo. Note: While
the cable is plugged into the LINE OUT jack, do not
plug your headphones into the headphone jack on
the console.
A
LINE OUT
A
CD
VCR
Amp
LINE OUT
LINE OUT
Audio Cable
Audio Cable
B. Plug one end of a long 1/8” to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into an RCA Y-adapter (available at electronics
stores). Next, remove the wire that is currently
plugged into the LINE OUT jack on your stereo and
plug the wire into the unused side of the Y-adapter.
Plug the Y-adapter into the LINE OUT jack on your
stereo. Note: While the Y-adapter is plugged into the
LINE OUT jack, do not plug your headphones into
the headphone jack on the console.
B
CD
VCR
Amp
LINE OUT
RCA
Y-adapter
Audio
Cable
Wire removed from
LINE OUT jack
23
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
HOW TO USE AN IFIT.COM MP3, CD, OR VIDEO
PROGRAM
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 23.
To use an iFIT.com MP3, CD, or video program, the
treadmill must be connected to your MP3 player, CD
player, or VCR. See HOW TO CONNECT THE
TREADMILL TO USE IFIT.COM PROGRAMS on
pages 22 to 24. To purchase and download
purchase iFIT.com CDs or videocassettes, call the
toll-free telephone number on the front cover of this
manual.
A. Plug one end of a long 1/8” to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into the AUDIO OUT jack on your VCR.
A
Follow the steps below to use an iFIT.com MP3, CD,
or video program.
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
AUDIO OUT
RIGHT
LEFT
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 13.
Identify yourself as user A, B, C, or D.
2
See step 2 on page 13.
Audio Cable
Select the iFIT.com mode.
3
B. Plug one end of a long 1/8” to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into an RCA Y-adapter (available at electronics
stores). Next, remove the wire that is currently
plugged into the AUDIO OUT jack on your VCR and
plug the wire into the unused side of the Y-adapter.
Plug the Y-adapter into the AUDIO OUT jack on
your VCR.
To select the
iFIT.com
mode, press
the
Programs
button until
the letters
“iFIT” ap-
pear in the
display.
B
ANT. IN
VIDEO AUDIO
IN
RF OUT
Press the Play button on your MP3 player, CD
player, or VCR.
CH
3
4
OUT
4
Note: If you are using an iFIT.com CD, insert the
CD into your CD player; if you are using an
iFIT.com videocassette, insert the videocassette
into your VCR.
RCA
Y-adapter
Audio Cable
A moment after the Play button is pressed, your
personal trainer will begin guiding you through
your workout. Simply follow your personal trainer’s
instructions. Note: If the time is flashing in the dis-
play, press the Start button or the Speed increase
button on the console. The treadmill will not re-
spond to an MP3, CD, or video program while the
time is flashing in the display.
Wire removed from
AUDIO OUT jack
24
Download from Www.Somanuals.com. All Manuals Search And Download.
During the program, an electronic “chirping” sound
will alert you when the speed and/or incline of the
treadmill is about to change. CAUTION: Always
listen for the “chirp” and be prepared for speed
and/or incline changes. In some instances, the
speed and/or incline may change before your
personal trainer describes the change.
• Adjust the volume of your MP3 player, CD
player, or VCR. If the volume is too high or too
low, the console may not detect the program
signals.
• Make sure that the audio cable is properly
connected.
• If you are using a portable CD player and the
CD skips, set the CD player on the floor or an-
other flat surface instead of on the console.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
Adjust the cushioning system as desired.
5
6
7
8
9
See step 6 on page 14.
To stop the walking belt at any time, press the
Stop button on the console. The time will begin to
flash in the display. To restart the program, press
the Start button or the Speed increase button.
After a moment, the walking belt will begin to
move at 1 mph. When the next “chirp” is heard,
the speed and/or incline will change to the
next settings of the program.
Follow your progress with the display.
See step 7 on page 14.
Measure your heart rate if desired.
See step 8 on page 15.
Turn on the fans if desired.
See step 9 on page 15.
When the program is completed, the walking belt
will stop. Note: To use another MP3, CD, or video
program, press the Stop button or remove the key
and go to step 1 on page 24.
When you are finished exercising, remove the
key from the console.
Note: If the speed and/or incline of the treadmill
does not change when a “chirp” is heard:
See step 10 on page 17.
• Make sure that the letters “iFIT” appear in the
display and that the time is not flashing in the
display. If the time is flashing, press the Start
button or the Speed increase button on the
console.
CAUTION: Always remove iFIT.com CDs and
videocassettes from your CD player and VCR
and disconnect your MP3 player when you are
not using them.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
HOW TO USE AN IFIT.COM PROGRAM
DIRECTLY FROM OUR WEB SITE
programs directly from the internet. Additional options
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings for the program.
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 23. In
addition, you must have an internet connection and
an internet service provider. A list of specific system re-
quirements is found on our Web site.
To stop the walking belt at any time, press the
Stop button on the console. The time will begin to
flash in the display. To restart the program, press
the Start button or the Speed increase button.
After a moment, the walking belt will begin to
move at 1.0 mph. When the next “chirp” is
heard, the speed and incline will change to the
next settings of the program.
Follow the steps below to use a program from our
Web site.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 13.
Identify yourself as user A, B, C, or D.
When the program is completed, the walking belt
will stop. Note: To use another program, press the
Stop button and go to step 5.
2
See step 2 on page 13.
Select the iFIT.com mode.
Note: If the speed and/or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the letters “iFIT” appear in the display
and that the time is not flashing in the display.
In addition, make sure that the audio cable is
properly connected.
3
See step 3 on page 24.
Go to your computer and start an internet
connection.
4
Start your web browser, if necessary, and go to
Adjust the cushioning system as desired.
5
9
See step 6 on page 14.
Follow the desired links on our Web site to se-
lect a program.
6
Follow your progress with the display.
10
See step 7 on page 14.
Read and follow the on-line instructions for using a
program.
Measure your heart rate if desired.
11
12
13
Follow the on-line instructions to start the
program.
7
See step 8 on page 15.
When you start the program, an on-screen count-
down will begin.
Turn on the fans if desired.
See step 9 on page 15.
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
8
When you are finished exercising, remove the
key from the console.
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
See step 10 on page 17.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE/DEMO MODE
To reset all programs to the
original settings, first press the
Start button. The word “SAVE”
will flash in the Pace/Speed
zone of the display. To reset
all programs, press the Save
button. If you do not wish to reset all programs, press
the Stop button.
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been used and the total number of miles that the walk-
ing belt has moved. The information mode also allows
you to select miles or kilometers as the unit of mea-
surement for the console, to turn on and turn off the
demo mode, and to reset all programs to the original
settings.
To exit the information mode, remove the key from the
console.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following informa-
tion will be shown in the display:
THE OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor offers hands-free oper-
ation and allows you to use the console’s heart rate
programs. To purchase the optional chest pulse
sensor, call the toll-free telephone number on the
front cover of this manual.
The Time zone of
the display will
show the total
number of hours
that the treadmill
Hours
has been used.
The Odometer
Miles
zone will show
the total number
of miles (or kilometers) that the walking belt has moved.
An “E” for English miles or an “M” for metric kilometers
will appear in the Pace/Speed zone. Press the Speed
increase button to change the unit of measurement if
desired.
IMPORTANT: If a “d” appears in the Heart Rate/
Calories zone of the display, the console is in the
“demo” mode. This mode is intended to be used only
when a treadmill is displayed in a store. When the con-
sole is in the demo mode, the power cord can be
plugged in, the key can be removed from the console,
and the indicators in the display will automatically light
in a preset sequence, although the buttons on the con-
sole will not operate. If a “d” appears when the infor-
mation mode is selected, press the Speed decrease
button so the “d” disappears.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be per-
manently damaged. Remove the key and unplug the power
cord. CAUTION: You must be able to safely lift 55 pounds
(25 kg) to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the location shown by
the arrow at the right. CAUTION: To decrease the possi-
bility of injury, bend your legs and keep your back
straight. As you raise the treadmill, make sure to lift
with your legs rather than your back. Raise the treadmill
about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the treadmill until the latch pin is
aligned with the indicated hole in the frame. Insert the
latch pin into the hole. Make sure that the latch pin is
fully inserted into the hole.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° Fahrenheit.
Knob
Hole
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the latch
pin is fully inserted into the hole in the side of the tread-
mill.
1. Hold the handrails as shown and place one foot against a
wheel.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Wheels
Base
3. Place one foot on wheel, and carefully lower the treadmill
until it is resting in the storage position.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left hand, pull the latch knob to the left
and hold it. Pivot the treadmill down until the frame is past
the pin on the latch knob.
Knob
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. To decrease the possibility of in-
jury, bend your legs and keep your back straight.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 11. Important: The treadmill is not com-
patible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch pro-
trudes as shown, the circuit breaker has tripped. To
reset the circuit breaker, wait for five minutes and
Reset
Tripped
then press the switch to the reset position.
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch to the reset position.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
a
POWER CORD. Carefully lower the Uprights (85).
Remove the two indicated Screws (7). Note: A phillips
screwdriver with an 8” shaft is required.
85
7
7
b. Raise the Uprights (85) to the vertical position.
b
7
Remove the three Screws (7) from the Hood (33), and
carefully pivot the Hood off.
85
33
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Locate the Reed Switch (22) and the Magnet (18) on
the left side of the Pulley (17). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, use a slotted
screwdriver to move the Reed Switch slightly.
Reattach the Hood (33), making sure that the Screws
(7) are inserted into the same holes from which they
were removed. Run the treadmill for a few minutes to
check for a correct speed reading.
Top
View
22
18
17
1/8”
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.
b. If the walking belt is overtightened, treadmill perfor-
b
3”–4”
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, in-
sert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, remove the key and
a
UNPLUG THE POWER CORD. If the walking belt
has shifted to the left, use the allen wrench to turn
the left rear roller bolt clockwise 1/2 of a turn; if the
walking belt has shifted to the right, turn the left
rear roller bolt counterclockwise 1/2 of a turn. Be
careful not to overtighten the walking belt. Plug in the
power cord, insert the key, and run the treadmill for a
few minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
b
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctly tight-
ened, you should be able to lift each side of the walk-
ing belt 3 to 4 inches off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
PROBLEM: The shock does not assist the lowering of the treadmill frame
SOLUTION: a. Environmental factors such as cold temperatures can decrease the performance of the shock. To
increase the performance, first hold the ends of the treadmill frame near the endcaps firmly with
both hands. Carefully lower the frame to the floor and then raise it several times. To decrease
the possibility of injury, bend your legs and keep your back straight.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
To measure your heart rate during exercise, use the
pulse sensor on the console.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
1
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot to-
ward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles ten-
dons, bend your back leg as well. Stretches: Calves, achilles ten-
dons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your but-
tocks as possible. Hold for 15 counts, then relax. Repeat 3 times
for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
5
33
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. NTL1495.2
R0205A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
9
1
20
1
20
2
1
43
2
5
4
2
2
4
2
1
1
1
1
2
8
1
1
13
1
1
1
2
1
2
2
2
8
1
3
1
1
4
Left Foot Rail
Foot Rail Screw
Front Left Endcap
Screw
Platform Screw, Front
Latch Warning Decal
3/4” Screw
Platform Screw, Rear
Spring Nut
Curved Washer
Spring Plate
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
1
1
1
1
1
2
2
2
2
6
2
1
1
1
4
12
1
1
1
2
2
1
1
2
1
1
1
1
2
4
6
2
2
1
1
4
2
2
1
1
1
1
1
1
1
1
1
1
2
2
1
Plastic Tie
Front Right Endcap
Right Foot Rail
Frame
Ground Wire
Platform Nut
Wheel Bolt
Rear Wheel
Rear Roller Star Washer
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39*
40
41
42
43
44
45
46
47
48
49
50
51
Rear Roller Washer/Spring Washer
Rear Roller Bolt
Right Rear Endcap
Rear Roller
Left Rear Endcap
Handrail Bolt
Belt Guide
Belt Guide Screw
Frame Pivot Bolt
Walking Platform
Walking Belt
Front Roller
Magnet
Frame Spacer
Nut
Reed Switch Clip
Reed Switch
1/2” Screw
Cushion Housing, Left
Drive Motor
Motor Belt
Leaf Spring
Controller Wire
Spring Pad
Spring Spacer
Motor Bolt
Platform Bracket
Motor Hood
Hood Clip
Hood Foam, Left
Upper Clevis Pin
Cotter Pin
Front Roller Adjustment Bolt
Idler Arm Assembly
Incline Motor
Lower Pin
Star Washer
Left Handrail
Pulse Bar Assembly
Right Handrail
Upright Endcap
Console Bolt
Wire Harness
Pulse Wire
Upright Cover
Latch Assembly
Latch Insert
Left Upright Cap
Cushion Housing, Right
Lift Frame Clevis Pin
Base Pad
1” Tek Screw
Thin Base Pad
Caution Decal
Uprights
Shock
Extension Screw
Front Wheel Bolt
Front Wheel
Base Extension
Right Upright Cap
Base Cover
iFIT Cable
Lift Frame
Access Door
Console Back
Right Accessory Tray
Console Front
Left Accessory Tray
Fan
1
1
1
1
1
1
14
1
1
1
1
1
2
Transformer
Controller
3/4” Screw
Belly Pan
Power Cord Grommet
Power Cord
Off/Reset Circuit Breaker
Outlet Bracket
Tie Holder
Endcap Screw
Console Base
1
Releasable Tie
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
1
4
1
1
1
1
1
1
1
2
1
1
1
2
1
2
1
1
1
1
1
1
1
1
4
2
1
4
2
2
Key/Clip
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
#
2
2
2
2
2
2
1
2
2
1
2
10
1
1
1
1
2
1
4
1
1
1
1
1
1
Isolator Top Cap
Isolator Spring
Isolator
Isolator Bottom Cap
Front Isolator
Cushion Rod Clips
Cushion Motor Nut
Cushion Adj. Pin
Cushion Adj. Wheel
Cushion Adj. Rod
Cushion Adj. Gear
Belly Pan Clip
Circuit Board Bracket
Cushion Sensor
Magnet Plate
Wheel Spacer
Console Insert
Console Cover
Book Holder
Filter Wire
Frame Belly Pan
Hood Foam, Right
Allen Wrench
Short Console Bolt
Upright Ground Wire
Rail Cover, Left
Rail Cover, Right
Static Decal
Pulse Extension Wire
Idler Pulley Washer
Idler Pulley
Idler Pulley Bolt
Idler Arm Bolt
Idler Bushing
Circuit Board
Isolator Screw
Cushion Adj. Motor
Plastic Stand-Off
22” Blue Wire, M/F
12” Blue Wire, 2F
4” Blue Wire, M/F
8” Green Wire, F/Ring
8” Black Wire, 2 Ring
User's Manual
Idler Arm
#
#
#
#
Idler Arm Spring
Cushion Motor Bolt
Handrail Coupler
Pulse Bar Bolt
Control Knob
Cushion Magnet
Spring Bolt
Spring Pad Screw
Gear Rack
#
*Includes all parts shown in box
#These parts are not illustrated
Specifications are subject to change without notice.
ORDERING REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. When ordering parts, please be prepared to give
the following information:
• the MODEL NUMBER OF THE PRODUCT (NTL1495.2)
• the NAME OF THE PRODUCT (NordicTrack® C2420 treadmill)
• the SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual)
• the KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST on pages 34 and 35 and the
EXPLODED DRAWING attached in the center of this manual)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
7
7
1
7
7
1
7
7
1
1
1
7
7
7
7
9
9
9 6
7
1
1
4
9
1
9
1
4
9
1
1
7
4
8
7
8
8
6
3
9
4
4
1
1
1
1
7
7
7
2
7
1
6
8
8
8
7
7
8
7
8
1
8 2
1
1
7
7
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
WHAT IS COVERED—The entire NordicTrack® C2420 treadmill (“Product”) is warranted to be free of all defects in ma-
terial and workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the drive motor for life. Parts and labor
are warranted for one year from the date of purchase.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or
component, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized
service provider, or, at our option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, im-
proper assembly or installation, alterations, modifications without our written authorization or by failure on your part to
use, operate, and maintain as set out in your User’s Manual (“Manual”). This warranty does not extend to products used
for commercial or rental purposes.
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the
Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discov-
ery of the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product.
Remember to do the periodic maintenance requirements specified in the Manual to assure proper operation and your
continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-888-825-2588 and tell them
your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if neces-
sary, arrange for service where your Product is located or advise you how to ship the Product for service. Before ship-
ping, always obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack
your Product (save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the
product. Include a letter explaining the product or problem and a copy of your proof of purchase if you believe the ser-
vice is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the
use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or
profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature.
Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above lim-
itation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability
or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not
allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty.
This warranty gives you specific legal rights and you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 223184 R0205A
Printed in USA © 2005 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|