Model No. NTBE06901
Serial No.
USERÕS MANUAL
Write the serial number in the
space above for reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-888-825-2588
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
Patent Pending
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Precautions
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the weight rack.
1. Read all instructions in this manual before
using the weight rack. Use the weight rack
only as described in this manual.
10. Always make sure there is an equal amount
of weight on each end of the barbell (not
included).
2. It is the responsibility of the owner to ensure 11. Do not place more than 300 pounds, includ-
that all users of the weight rack are ade-
quately informed of all precautions.
ing the barbell, on the weight rests. Do not
place more than 150 pounds on the weight
carriage.
3. The weight rack is intended for home use
only. Do not use the weight rack in any com-
mercial, rental, or institutional setting.
12. Make sure that the cables remain on the pul-
leys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys.
4. Use the weight rack only on a level surface.
Cover the floor beneath the weight rack to
protect the floor or carpet.
13. Always secure the weights (not included)
with the weight clips when they are mounted
on the weight carriage.
5. Inspect and tighten all parts each time you
use the weight rack. Replace any worn parts
immediately.
14. Always exercise with a partner. When you
are performing squat exercises, your partner
should stand behind you to catch the barbell
if you cannot complete a repetition.
6. Keep children under 12 and pets away from
the weight rack at all times.
7. Keep hands and feet away from moving parts. 15. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
8. Always wear athletic shoes for foot protec-
tion while exercising.
ing down.
16. Always disconnect the lat bar from the
weight rack when performing an exercise
that does not require the lat bar.
9. Always set both weight rests and both
weight spotters at the same height.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Thank you for selecting the versatile NordicTrack¨
GRT 400 weight rack. The NordicTrack¨ GRT 400 is
designed to help you develop every major muscle
group of the body. Whether your goal is a shapely fig-
ure, dramatic increase in muscle size and strength, or
a healthier cardiovascular system, the NordicTrack¨
GRT 400 will help you achieve the specific results you
want.
toll-free at 1-888-825-2588, Monday through Friday, 6
a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is NTBE06901. The serial number can be
found on a decal attached to the weight rack (see the
front cover of this manual).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the weight rack. If you have additional ques-
tions, please call our Customer Service Department
High Pulley Station
Chin-up Bar
Lat Bar
Right Side
Left Side
Weight Rest
Weight Carriage
Weight Tube
Weight Spotter
Low Pulley
Station
Note: The terms Òright sideÓ and Òleft sideÓ are
determined relative to a person using the rack;
they do not correspond to right and left on the
drawings in the manual.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Identification ChartÑModel No. NTBE06901
R1000A
M10 x 45mm Bolt (32)Ð3
51mm Spacer (39)Ð1
M10 x 50mm Bolt (43)Ð2
28mm Spacer (40)Ð2
M10 x 66mm Bolt (35)Ð2
24mm Spacer (38)Ð2
18mm Spacer (41)Ð4
M8 x 72mm Bolt (33)Ð4
M10 x 75mm Bolt (34)Ð3
M10 Nylon Locknut (29)Ð46
M10 x 78mm Bolt (31)Ð36
M8 Nylon Locknut (30)Ð4
M10 Flat Washer (37)Ð12
M8 Flat Washer (36)Ð8
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
¥ As you assemble the weight rack, make sure all
parts are oriented as shown in the drawings.
Make Things Easier for Yourself!
Everything in this manual is designed to ensure
that the weight rack can be assembled success-
fully by anyone. However, it is important to real-
ize that the versatile weight rack has many parts
and that the assembly process will take time.
Most people find that by setting aside plenty of
time, assembly will go smoothly.
¥ For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5.
The following tools (not included) are required
for assembly:
¥ Two adjustable wrenches
¥ One rubber mallet
Before beginning assembly, carefully read the
following information and instructions:
¥ One standard screwdriver
¥ One Phillips screwdriver
¥ Assembly requires two people.
¥ Lubricant, such as grease or petroleum jelly,
and soapy water.
¥ Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
¥ Tighten all parts as you assemble them, unless
instructed to do otherwise.
1. Press 60mm Square Outer Caps (27) onto the ends
of the Right and Left Bases (1, 3).
1
27
29
Attach the Right and Left Bases (1, 3) to the Center
Base (2) using four M10 x 78mm Bolts (31) and
four M10 Nylon Locknuts (29). Do not tighten the
Nylon Locknuts yet.
2
31
27
29
1
27
31
27
3
2. Identify the two Rear Uprights (8), which are slightly
shorter than the Front Uprights (not shown).
2
Adjustment
Holes
Attach the Rear Uprights (8) to the Left and Right
Bases (1, 3) using four M10 x 78mm Bolts (31) and
four M10 Nylon Locknuts (29). Do not tighten the
Nylon Locknuts yet. Make sure the Uprights are
oriented exactly as shown, with the adjustment
holes on the indicated side near the bottom.
8
8
29
27
31
4
29
2
1
Press a 60mm Square Outer Cap (27) onto the end
of the Weight Guide Base (4).
29
Orient the Foot Plate (5) and the Weight Guide
Base (4) as shown. Attach the Foot Plate and the
Weight Guide Base to the Center Base (2) using
two M10 x 78mm Bolts (31) and two M10 Nylon
Locknuts (29). Do not tighten the Nylon Locknuts
yet.
31
5
3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Attach one of the Front Uprights (7) and two Joint
Plates (6) to the Left Base (3) using four M10 x
78mm Bolts (31) and four M10 Nylon Locknuts (29).
Make sure the Front Upright is oriented so that
the holes on the bottom of the Front Upright
and the holes in the Joint Plates line up. If they
do not line up, turn the Front Upright upside-
down. Do not tighten the Nylon Locknuts yet.
Make sure the Front Upright is turned so the
adjustment holes are facing the Rear Upright
(8).
3
28
7
8
Adjustment
Holes
1
Attach the other Front Upright (7, not shown) and
two Joint Plates (6, not shown) to the Right Base
(1) in the same manner.
31
29
Tap a 60mm Square Inner Cap (28) into the top of
each of the Front Uprights (7).
3
6
29
6
4. Refer to drawing 4a. Press Square Bushings (21)
into the top and bottom of one of the Weight Rests
(19) and one of the Weight Spotters (20) as shown.
Pull out the Adjustment Knobs (22) and slide the
Weight Spotter and the Weight Rest down over the
right Uprights (7, 8) as indicated.
4a
4b
21
22
7
19
8
21
19
22
Refer to drawing 4b. Secure the Weight Spotter
(20) and the Weight Rest (19) to the right Uprights
(7, 8) by snapping each of the three Adjustment
Knobs (22) into one of the adjustment holes in the
Uprights and turning them clockwise until tight.
20
22
21
20
22
Assemble the other Weight Spotter (20) and Weight
Rest (19) to the left Uprights (7, 8) in the same
manner. Make sure both Weight Spotters and
both Weight Rests are at the same height.
8
7
5. Attach the Chin-up Bar (13) and two Joint Plates (6)
to the Front Uprights (7) using four M10 x 78mm
Bolts (31) and four M10 Nylon Locknuts (29). Do
not tighten the Nylon Locknuts yet.
5
6
29
13
31
6
31
7
7
29
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Press a 60mm Square Inner Cap (28) into the Left
Frame (12). Attach the Left Frame to the left
Uprights (7, 8) using four M10 x 78mm Bolts (31)
and four M10 Nylon Locknuts (29). Do not tighten
the Nylon Locknuts yet.
6
11
29
10
29
28
Assemble the Right Frame (10) to the right Uprights
(7, 8) in the same manner.
31
8
31
12
Attach the Center Frame (11) to the Left Frame (12)
and the Right Frame (10) using four M10 x 78mm
Bolts (31) and four M10 Nylon Locknuts (29).
Tighten all Nylon Locknuts used in steps 1Ð6.
29
8
31
7
31
29
7
7. Press the two 51mm Round Inner Caps (42) into
the weight tubes on the Weight Carriage (15).
7
42
16
15
Press the two Carriage Bushings (16) into the
Weight Carriage (15). Make sure the Weight
Carriage is turned so the weight tubes are near
the top, as shown. Attach the lower Carriage
Bushing using an M10 x 66mm Bolt (35), two M10
Flat Washers (37), the 51mm Spacer (39), and an
M10 Nylon Locknut (29).
Weight Tube
42
29
37
16
39
37
35
8. Set the two Weight Bumpers (18) over the indicated
holes in the Weight Guide Base (4). Hold the
Weight Carriage (15) on top of the Weight
Bumpers.
8
9
15
Insert the two Weight Guides (9) into the Weight
Carriage (15), the Weight Bumpers (18), and the
Weight Guide Base (4). Attach the Weight Guides
using two M8 x 72mm Bolts (33), four M8 Flat
Washers (36), and two M8 Nylon Locknuts (30).
30
18
4
36
33
9. Press a 60mm Square Inner Cap (28) into the end
of the Weight Guide Frame (14).
36
9
30
28
36
31
Hold the Weight Guide Frame (14) on top of the
Center Frame (11) and the Weight Guides (9).
Attach the Weight Guides to the Weight Guide
Frame using two M8 x 72mm Bolts (33), four M8
Flat Washers (36), and two M8 Nylon Locknuts (30).
14
33
11
Attach the Weight Guide Frame (14) to the Center
Frame (11) using two M10 x 78mm Bolts (31), two
M10 Flat Washers (37), and two M10 Nylon
Locknuts (29).
9
37
29
8
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Locate a Cable (25) and notice that there is a ball
on one end of the Cable and a metal sleeve on the
other end.
10
14
Route the metal-sleeve end of the Cable (25) up
under the lat bar rest on the Weight Guide Frame
(14), down through the indicated hole, back up
through the next hole, and then down through the
hole between the Weight Guides (9) as shown.
9
Lat Bar
Rest
25
11. Insert the end of the Cable (25) into the hole in the
center of the Weight Carriage (15). Attach the Cable
using an M10 x 66mm Bolt (35), two M10 Flat
Washers (37), two 24mm Spacers (38), and an M10
Nylon Locknut (29).
11
37
25
38
38
29
37
35
15
12 Lift the Cable (25) in the location shown. Attach two
Pulleys (24) inside the bracket on the Weight Guide
Frame (14) using two M10 x 50mm Bolts (43) and
two M10 Nylon Locknuts (29).
12
24
25
14
29
43
13. Lift the Cable (25) in the location shown. Attach two
Pulleys (24) inside the Weight Guide Frame (14)
using two M10 x 75mm Bolts (34), four M10 Flat
Washers (37), four 18mm Spacers (41), and two
M10 Nylon Locknuts (29).
13
24
25
37
14
29
41
41
37
41
37
34
41
37
9
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Pull the Cable (25) down in the indicated location,
so there is no slack at the ends of the Cable.
14
Locate the other Cable (25). Insert the metal-sleeve
end of the Cable into the indicated hole in the
Weight Guide Base (4). Attach the Cable using an
M10 x 75mm Bolt (34), two M10 Flat Washers (37),
two 28mm Spacers (40), and an M10 Nylon Locknut
(29).
25
Route the ball-end of the Cable (25) through the
bracket on the Center Base (2). Attach a Pulley (24)
inside the bracket using an M10 x 45mm Bolt (32)
and an M10 Nylon Locknut (29).
25
24
37
40
4
40
29
37
34
2
32
15. Wrap the upper Cable (25) around a Pulley (24) as
shown. Attach the Pulley and a Cable Trap (23) to
the two Pulley Plates (17) using an M10 x 45mm
Bolt (32) and an M10 Nylon Locknut (29).
15
25
17
24
Wrap the lower Cable (25) around a Pulley (24) as
shown. Attach the Pulley and a Cable Trap (23) to
the Pulley Plates (17) using an M10 x 45mm Bolt
(32) and an M10 Nylon Locknut (29).
29
23
17
Make sure the Bolts (32) are in the highest and
lowest holes in the Pulley Plates (17). In addition,
make sure the Cables (25) are between the Cable
Traps (23) and the Pulleys (24).
32
23
25
16. Wet the ends of the Lat Bar (45) with a small
amount of soapy water. Slide the Handgrips (47)
onto the ends of the Lat Bar.
16
17. Make sure all parts of the weight rack are prop-
erly tightened. In addition, pull each cable a few
times to make sure the cables move smoothly
over the pulleys. If the cables do not move
smoothly, locate and correct the problem. When
weights are used, the cables may be damaged if
they are incorrectly routed.
45
47
The use of all remaining parts will be explained in
ADJUSTING THE WEIGHT RACK, beginning on
page 11.
47
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Weight Rack
This section explains how to adjust the weight rack. See the Exercise Guidelines on page 13 for important infor-
mation about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise
poster to see the correct form for each exercise.
Inspect and tighten all parts each time you use the weight rack. Replace any worn parts immediately. The weight
rack can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
USING THE WEIGHT RESTS AND WEIGHT
SPOTTERS
Adjustment
Holes
8
Before beginning an exercise, move the Weight Rests
(19) and the Weight Spotters (20) to sets of holes in the
Uprights (7, 8) that are best suited for that exercise. Do
this by turning the Adjustment Knobs (22) counterclock-
wise until loose. Pull the Knobs out and slide the
Weight Rests or the Weight Spotters to the desired
height. Snap the Knobs into the adjustment holes in the
Uprights and turn the Knob clockwise until tight.
7
19
20
22
The selected holes for the Weight Spotters (20) should
represent the lowest point to which you want the barbell
to go during the exercise. The selected holes for the
Weight Rests (19) should be at a comfortable height for
lifting and replacing the barbell. Perform the exercise as
shown in the accompanying exercise poster. Note:
Make sure the Adjustment Knobs (22) are fully tight-
ened.
WARNING:Always set both Weight
Rests (19) at the same height and both Weight
Spotters (20) at the same height.
SETTING UP FOR SQUAT EXERCISES
Squat exercises should be performed inside the rack
(behind the dotted line in the picture). When performing
squat exercises, set the Weight Rests (19) and the
Weight Spotters (20) at a comfortable height in the
manner described in USING THE WEIGHT RESTS
AND WEIGHT SPOTTERS, above.
19
20
19
20
Squat
Area
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING WEIGHTS TO THE WEIGHT CARRIAGE
Weight
Tube
To use the high or low pulley station, slide the desired
amount of weight onto the weight tubes of the Weight
Carriage (15) and secure the weights with Weight Clips
(48).
Weight
Tube
WARNING:
Do not place more than
150 pounds on the Weight Carriage (15). Always
place the same amount of weight on each side of
the Weight Carriage, and secure the weights on
the Weight Carriage with the Weight Clips (48).
15
48
ATTACHING THE LAT BAR TO THE HIGH PULLEY
STATION OR THE LOW PULLEY STATION
25
To use the high pulley station or the low pulley station,
first place the desired weights on the weight carriage
(see ATTACHING WEIGHTS TO THE WEIGHT CAR-
RIAGE above). Next, attach the Lat Bar (45) to either
Cable (25) with a Cable Clip (46).
46
45
WARNING: Always disconnect the
Lat Bar (45) when performing an exercise that
does not require using the Lat Bar.
TIGHTENING THE CABLES
Woven cable, the type of cable used on the weight rack,
can stretch slightly after it is first used. If there is slack
in the cables, tighten them as described below.
17
24
29
23
17
Remove the M10 x 45mm Bolt (32) and the M10 Nylon
Locknut (29) attaching the lower Pulley (24) and Cable
Trap (23) to the two Pulley Plates (17). Reattach the
lower Pulley and Cable Trap to the higher holes in the
Pulley Plates using the Bolt and Nylon Locknut.
32
23
If moving just the lower Pulley (24) does not sufficiently
tighten the cables, you can also move the upper Pulley
down one set of holes in the Pulley Plates (17).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Exercise Guidelines
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
Specifying the exact length of time for each workout,
as well as the number of repetitions or sets for each
exercise, is a highly individual matter. It is very impor-
tant to avoid overdoing it during the first few months
of your exercise program. You should progress at
your own pace and be sensitive to your bodyÕs sig-
nals. If you experience pain or dizziness at any time
while exercising, stop immediately and begin cooling
down. Find out what is wrong before continuing.
Remember that adequate rest and a proper diet are
important factors in any exercise program.
The only way to increase the size and strength of
your muscles is to push them close to their maximum
capacity. When you progressively increase the inten-
sity of your exercise, your muscles will continually
adapt and grow. You can tailor the individual exercise
to the proper intensity level in two ways:
¥ by changing the amount of weight used
¥ by changing the number of repetitions or sets per-
formed (A ÒrepetitionÓ is one complete cycle of an
exercise, such as one sit-up. A ÒsetÓ is a series of
repetitions).
WARMING UP
The proper amount of weight for each exercise obvi-
ously depends upon the individual user. You must
gauge your limits and select the amount of weight that
is right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repeti-
tions without difficulty, increase the amount of weight.
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
WORKING OUT
Toning
You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a mod-
erate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.
Each workout should include 6 to 10 different exercis-
es. Select exercises for every major muscle group
with emphasis on the areas that you want to develop
the most. To give balance and variety to your work-
outs, vary the exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
You will gain the greatest benefits from exercising by
maintaining proper form. This requires moving
through the full range of motion for each exercise and
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise poster accompa-
nying this manual, you will find photographs showing
the correct form for several exercises. A description of
each exercise is also provided, along with a list of the
muscles affected. Refer to the muscle chart on page
14 to find the locations of the muscles.
Cross Training
Many people desire a complete and balanced fitness
program. Cross training is an efficient way to accom-
plish this. One example of a balanced program is:
¥ Plan weight training workouts on Monday,
Wednesday, and Friday.
¥ Plan 20 to 30 minutes of aerobic exercise, such as
cycling, running, or swimming on Tuesday and
Thursday.
¥ Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of weight training and aerobic exer-
cise will reshape and strengthen your body and devel-
op your heart and lungs.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath!
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure to rest for a short period of time after each
set. The ideal resting periods are:
¥ Rest for three minutes after each set for a muscle
building workout.
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout is
very effective for increasing flexibility.
¥ Rest for one minute after each set for a toning
workout.
STAYING MOTIVATED
¥ Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
For motivation, keep a record of each workout. The
chart on page 15 of this manual can be photocopied
and used to schedule and record your workouts. List
the date, the exercises performed, the weight plus the
numbers of sets and repetitions completed. Record
your weight and key body measurements at the end of
every month.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
Remember, the key to achieving the greatest results is
to make exercise a regular and enjoyable part of your
everyday life.
MUSCLE CHART
Trapezius
Pectoralis
Major
Deltoid
Trapezius
Rectus
Abdominus
Biceps
Deltoid
Obliques
Brachioradials
Rhomboideus
Triceps
Abductor
Latissimus Dorsi
Spinae Erectors
Brachioradials
Hip Flexors
Quadriceps
Adductor
Gluteus
Medius
Gluteus
Maximus
Soleus
Abductors
Hamstring
Gastrocnemius
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Replacement Parts
To order replacement parts, simply call our Customer Service Department toll-free at 1-888-825-2588, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
¥ The MODEL NUMBER of the product (NTBE06901)
¥ The NAME of the product (NordicTrack¨ GRT 400 weight rack)
¥ The SERIAL NUMBER of the product (see the front cover of this manual)
¥ The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING at the center of this manual).
Limited Warranty
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which war-
ranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-autho-
rized by ICON. This warranty does not extend to any product or damage to a product caused by or attribut-
able to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center, products used for commercial or rental purposes, or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential dam-
ages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 171090 R1000A
Printed in China © 2000 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE THIS PART LIST/EXPLODED
DRAWING FROM THE MANUAL
SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Part ListÑModel No. NTBE06901
R1000A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
6
2
2
2
1
1
1
1
1
1
2
2
2
2
2
12
6
2
7
2
Right Base
Center Base
Left Base
Weight Guide Base
Foot Plate
Joint Plate
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
#
4
5
5
46
4
36
3
4
3
2
8
12
2
1
2
4
2
2
1
1
Weight Clip Sleeve
60mm Square Outer Cap
60mm Square Inner Cap
M10 Nylon Locknut
M8 Nylon Locknut
M10 x 78mm Bolt
M10 x 45mm Bolt
M8 x 72mm Bolt
M10 x 75mm Bolt
M10 x 66mm Bolt
M8 Flat Washer
M10 Flat Washer
24mm Spacer
51mm Spacer
28mm Spacer
18mm Spacer
51mm Round Inner Cap
M10 x 50mm Bolt
Strap
Front Upright
Rear Upright
Weight Guide
Right Frame
Center Frame
Left Frame
Chin-up Bar
Weight Guide Frame
Weight Carriage
Carriage Bushing
Pulley Plate
Weight Bumper
Weight Rest
Weight Spotter
Square Bushing
Adjustment Knob
Cable Trap
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Lat Bar
Cable Clip
Handgrip
Weight Clip
UserÕs Manual
Exercise Poster
2
2
2
1
Pulley
Cable
#
1
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the userÕs manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|