Owner’s Manual
Please read and fully understand this manual before
operating your NEWPORT 9000.
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
CONTROLS & AIR FLOW VENTS
Front Face Plate
Air Outlet
Dust Sensor
Air Inlets
Air Inlets
Front Panel Release Tabs
Bottom Stand
Soft Touch Control Panel
Remote Control
Odor Sensor
ON/OFF
AUTO
FLOW
ION UV
TIMER
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
MAJOR COMPONENTS
Back View
Exploded Parts View
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
BEFORE USE
Pre-Installation Air Ventilation
Open Windows for Air Ventilation
Before plugging in the unit,
please open the windows in
the area where you will be using
the unit. Ventilate the area for 2-3
hours if possible. Once the area
has been ventilated, close the
windows and plug in the unit.
After plugging in, the unit sensor will sample the air and retain a memory of the existing indoor
air condition. (The existing indoor air condition will be input as "CleanAir").
Once started, the odor indicator will blink as it memorizes the existing fresh air condition.
After two minutes, the indicator will stop blinking to indicate the end of memorization.
Please Note: Whenever the unit is unplugged, all memorized content will be erased.
If the unit is turned on two minutes after plugging it in, the odor sensor indicator will not blink.
When smoke, cosmetics, or any spray that contains alcohol is present, please ventilate and
freshen the air before closing windows.
Sometimes the sensor is not as sensitive when first purchased or after being unplugged
for over a week. Its sensitivity will begin to increase after one to two days of operation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
EXPLANATION OF INDICATORS
Negative Ion Indicator
During the process when negative ions are generated, the blue indicator on the Soft Touch Control Panel
will gradually change from bright to dim and from dim back to bright every 5seconds.
Odor Indicator
The odor indicator on the Soft Touch Control Panel will glow whenever the odor sensor detects odor
(such as indoor smoke).
Dust and Irritant Indicator
The dust-and-irritant indicator on the Soft Touch Control Panel will glow whenever dust or other irritants
are detected.
Air Quality Surveillance
Whenever odor, dust, or irritants are detected, the air quality surveillance function will indicate the level
of pollution on the Soft Touch Control Panel. When pollution is severe, all the LED’s will glow.
LED Examples for Air Quality Surveillance
No pollution detected
Some pollution detected
Severe pollution detected
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
OPERATING INSTRUCTIONS
Locate the Unit
Place the Newport 9000 against a wall, near an electric outlet with 12-15 inches clearance on the front
and sides. It is best to place the unit where it will be out of any children's play area.
How to Start
Plug the unit into a standard 120V/60Hz outlet. Press the POWER ON/OFF button. The device starts
operating automatically and the negative-ion UV indicator will automatically turn on. Press POWER ON/OFF
again and the device will turn off.
Fan Modes
This Newport 9000 has five different fan modes to choose from. Please choose a proper
level of circulation according to indoor air quality and room size. As you press FAN,
the fan mode will change according to the number of times you press the button.
The LED will show the following sequence of modes:
QUIET
LOW
MED
HI
AUTO
Automatic Operation
Keep pressing the FAN button until the device runs under automatic operation
(the LED will show AUTO).
Under automatic operation, the device automatically switches to the proper
running modes (MED or LOW) according to the level of odor, dust, or irritants
in the air as detected by the sensor. As the air is purified, the device will auto-
matically switch back to LOW or QUIET modes.
Timed ON/OFF
Press AUTOTIMER button to set operation timing.
Under the AUTOTIMER function, the operation timing will be set according to
the number of times you press the AUTOTIMER button. The LED will show the
following sequence of timing:
1 HOUR
2 HOUR
8 HOUR
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
CLEANING AND MAINTENANCE
Before starting any cleaning or maintenance, always turn-off and unplug the unit.
Regular cleaning and maintenance is recommended every 2-3 months.
Disassembling the Newport 9000
After unplugging, carefully lay the unit down face-up. Disassemble the unit in sequence of 1 to 5
as shown below. (Put the unit back together in the reverse 5 to 1 sequence.)
3. Remove the Washable Plasma Dust Filter
1. Remove the Front Face Plate
4. Remove the HEPA/Activated Charcoal Filter
2. Remove the Washable Pre-Filter
.
.
.
5. Remove the TiO2 Filter
Hold the clips of both sides to help pulling
out the filter.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
(
CLEANING AND MAINTENANCE CONT.
)
Regular Cleaning and Maintenance
Unit Body
Front Face Plate
For
Instructions
regarding the
disassembly of the
Can be cleaned with flowing water
face plate and
filters refer to
page 7.
Please use a soft cloth to clean and avoid scraping
off the paint on the cover
Take down UV lamp before cleaning
Use wring dry cloth to rub and clean.
Avoid cleaning with hot water or rubbing too hard
or paint damage or deformation could occur.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
(
CLEANING AND MAINTENANCE CONT.
)
Cleaning and Maintenance of the Washable Plasma Dust Filter
The Washable Plasma Dust Filter needs cleaning when:
1) The cleaning indicator is glowing or blinking.
2) The dust collector is making electrical discharge sounds.
3) The device has been used frequently in an area with lower
air quality condition.
Cleaning Instructions
1. Remove the Front Face Plate.
Washable Pre-Filter
Washable Plasma Dust Filter
2. Remove the Washable Pre-Filter.
Please refer to
page 7 for detailed
instructions on the
removal of the Front Face
Plate, Washable Pre-Filer
and the Washable
Plasma Dust
Filter.
3. Remove the Washable Plasma Dust Filter
Note: Please wear protective gloves to avoid
cutting or scratching your hands.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
(
CLEANING AND MAINTENANCE CONT.
)
The Cleaning and Maintenance of the Washable Plasma Dust Filter (Cont.)
4. Clean the Plasma Dust Filter
Use mild detergent or plain water only.
Use a soft scouring pad or toothbrush to
clean the dust collector.
Use warm water (below 40° C) only!
5. If dust and dirt does not wash away easily, pre-soak with diluted
detergent and then use a toothbrush to scrub.
Please take care not to damage any wiring while cleaning the dust collector
If any electrical discharge wire is broken, the device will lose part or
all of its dust collecting capability.
Any broken wire should be thrown away instead of being left inside the unit.
Otherwise, a dangerous short-circuit or high-voltage sparks may occur.
Please contact [email protected] for additional electrical discharge wire.
Please do not clean using acidic or alkaline detergent that can create rust on the surface of device.
Plastic Wrap
6. Thoroughly dry all washed parts.
After cleaning, please completely dry the unit before use.
Operating a wet unit may cause electrical shock or malfunction.
If the front cover of the plasma dust collector is not properly installed,
the unit will not function.
Please make sure the plastic wrap for the electrical discharge wire
is located in its proper position.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
(
CLEANING AND MAINTENANCE CONT.
)
Replacing
Filters
Please change
filter when
the REPLACE
FILTER
indicator is
glowing.
Note: Please ref
er to page 7 f
or instructions on
filter installation and remo
val.
Replacing
UV Lamp
The life span
of UV lamp
is about 5,000
hours. Replace
UV lamp when
it is damaged
or when no
blue light is
observed.
Remove the
the UV lamp
Front Face
(refer to page
Plate, Washable
7 on how to
dissemble).
Pre-Filter, W
ashable Plasma
Dust Filter,
and HEPA/Charcoal
filter before
replacing
Softly twist
the UV lamp,
remove the
lamp from its
position, and
insert a lamp
tube of the
same model.
Resetting
the CLEAN
METAL
GRID and
REPLACE
FILTER
Indicators
After cleaning
Otherwise the
The unit must
and replacing
two indicators
filters, reset
the CLEAN
METAL GRID
and REPLACE
FILTER indicators.
will remain
on after servicing
the unit.
be plugged
but turned of
f to reset the
CLEAN MET
AL GRID and
shaped object
REPLACE
FILTER indicators.
The RESET
Please use
button is inside
the unit (cannot
be reached
with finger).
a toothpick,
straightened
paper clip or
other similar
to push the
RESET button.
How to Reset:
1. CLEAN
METAL GRID
Indicator
When the unit
is plugged in,
but turned of
f, the resetting
process for
the CLEAN
METAL GRID
indicator is
done by
pushing both
same time.
the RESET
and the TIMER
buttons at the
2. REPLACE
FILTER
Indicator
When the unit
is plugged in,
but turned of
f, the resetting
process for
the REPLACE
FILTER indicator
is done by
Pushing both
the RESET
and the FLOW
buttons
at the same
time.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
FREQUENTLY ASKED QUESTIONS
Air Quality Surveillance
Why is there is only one LED glowing all the time with the air quality surveillance function?
Indoor air has been clean the whole time.
For testing purpose, dust either caused by a cigarette or a dusty cloth can be released near the irritant sensor.
If the level of pollution goes up, then the unit should be operating properly.
The irritant sensor could be too far away from any irritant for it to detect. Please move the unit closer to your
major sources of pollution
Why does the air quality surveillance indicator always have two LED glowing?
Possibly because the room is not really a closed environment and pollution keeps coming in from the outside.
Or, because there has been pollution created indoors (e.g. smoking/pet boxes etc.) the whole time. It will
take some time for the Newport 9000 to achieve a clean environment with only one indicator LED on.
Why does the air quality surveillance function keep switching back and forth frequently?
Sometimes the Irritant Sensor is affected by cell phone or other wireless equipment. When using cell phone
or other wireless equipment, please stay away from the unit.
Dust and Irritant Sensor
Why does the Dust and Irritant Sensor keep blinking?
In some locations the top of the sensor will accumulate more dust than in others Locations, This will decrease
the efficiency of the sensor. (Please refer to page 8 for the cleaning of the sensor.)
Odor Sensor
Why doesn't the Odor Sensor work?
In the initial set-up of the unit the Odor Sensor did not get properly trained. Please retrain the sensor memory.
(Please refer to page 4 on details under Before Use).
When first purchased or when the unit has been unplugged for more than a week, the sensor will not be as
sensitive. After 1 to 2days of operation, the sensor will regain its sensitivity.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
(
FREQUENTLY ASKED QUESTIONS CONT.
)
Filter
Why is it so hard for the filter to get rid of dust and odors?
Have the front and back of the HEPA/Charcoal filter been mistakenly reversed?
The HEPA/Charcoal filter has been saturated with a serious amount of dust. (Usually dark grey in color).
Please replace filter.
Plasma Dust Collector
Why is it so difficult to eliminate dust and odor?
If the electrical discharge wires or the plasma dust collector gets too dirty. Please refer to page 10
on how to clean and maintain.
additional information and parts.
Cannot Turn On the Unit
Why is the unit not working even after turning it on?
Has the plug been loosened or disconnected from the socket? Please check that the plug is properly
plugged in to an outlet.
Has the unit been properly reassembled after being cleaned? Please confirm. The unit will not operate if
the Washable Plasma Dust Filter or the Front Face Plate have not properly installed.
APPLICABLE AREAS
The unit is designed for any indoor room or living space up to 80 square meters or over 800 square feet.
It can be used in living or family rooms, bedrooms, offices, studios, waiting rooms, hotels, hospitals, etc.
If the unit is to be used in a smaller room, you may prefer to have the power setting on medium or low.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PureAirTM Newport 9000 Owner’s Manual
TECHNICAL SPECIFICATIONS
Real Spirit Style No.: Newport 9000
Rated Voltage: AC 120V/60Hz
Dust Removal Rate: 1 micron 99.97% • 0.3 micron 80%
Noise Level (dB): Quiet 20 • Low 35 • Med 45 • High 52
Air Volume (High): 3 m3/min. • 106 ft3/min.
Dimensions: 13.5" x 10" x 25.6” • 343 x 255 x 610 mm
Weight: 15.1 lbs • 6850 g
Power Consumption: 80W
Ion Output: ˃ 2 x 106/cm3
Activated Oxygen Output: ˂ 0.05 ppm
UV Spectrum: ˃ 20μ w/cm2 at 10 cm distance.
Applicable Area: 80 m2 • 861 ft2
PRODUCT SERVICING
In case of any malfunction, contact your retailer or email us at [email protected]..
PRODUCT WARRANTY
Advanced PureAir warrants the Newport 9000 air purifier to be free from manufacturing and
material defects (excluding filters, lights, and batteries) for a period of one year from the
original date of purchase.
This warranty is valid only to the original owner with proof of purchase.
Product abuse, misuse, modification, alteration, or opening of the unit housing, other than as
required for filter replacement or routine maintenance and cleaning, will void the warranty.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Produced and distributed exclusively by:
Real Spirit USA, Inc. • 9447 De Soto Ave • Chatsworth, CA 91311
Customer Service Phone 888.698.2080, ext. 210
© Copyright Real Spirit USA, Inc. 2008. All Rights Reserved
Manufactured in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|