Nilfisk P 130.2/150.2/160.2
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
EN
Index
1 Safety precautions and warnings .............................................3
2 Description ...............................................................................5
3 Before you start using your pressure washer...........................6
4 Operating your pressure washer..............................................7
5 Fields of application and working methods ............................11
6 After using your pressure washer...........................................13
7 Maintenance...........................................................................14
8 Trouble Shooting ....................................................................15
9 Further information.................................................................16
10 EC Declaration of Conformity.................................................18
1 Safety Precautions and Warnings
Symbols used to mark in-
structions
Before starting up
your high-pres-
sure washer for
the first time, this
instruction manual
This symbol is
used to mark
safety instruc-
tions that must
be observed to
must be read through carefully.
Save the instructions for later
use.
prevent damage to the
machine and its performance.
This symbol
indicates tips
and instructions
Safety instructions
marked with this
symbol must be
observed to pre-
to simplify work and to ensure a
safe operation.
vent danger to persons.
Do not let children or people
who have not read the instruc-
tion manual operate the ma-
chine.
tact your Nilfisk distributor.
Hold the spray lance firmly
with both hands. The spray
lance is affected by a thrust
of up to 16.4 N during ope-
ration.
The operator and anyone in
the immediate vicinity of the
site of cleaning should take
action to protect themselves
from being struck by debris
dislodged during operation.
Wear goggles during opera-
tion.
This appliance has been de-
signed for use with cleaning
agents supplied or recom-
mended by the manufacturer.
The use of other cleaning
agents or chemicals may
Especially check:
The insulation of the electric
cable should be faultless
and without any cracks. If the
electric cable is damaged, an
authorized Nilfisk distributor
should replace it.
This appliance is not intended
for use by children or other
persons without assistance or
supervision if their physical,
sensory or mental capabili-
ties prevent them from using it
safely. Children should be su-
pervised to ensure that they do
not play with the appliance.
WARNING!
High pressure jets can be
dangerous. Never direct the
water jet at persons, pets,
live electrical equipment or
the machine itself.
Never try to clean clothes or
footwear on yourself or other
persons.
Before starting up your machine
please check it carefully for any
defects. If you find any, do not
start up your machine and con-
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
adversely affect the safety of
the appliance.
Disconnect from electrical
power supply before carrying
out user maintenance.
To ensure the appliance
safety only use original spare
parts from the manufacturer
or approved by the manufac-
turer.
High pressure hoses, fittings
and couplings are important
for the safety of the appli-
ance. Only use hoses, fittings
and couplings recommended
by the manufacturer.
Do not use the appliance
if a supply cord or impor-
tant parts of appliance are
damaged, e.g. safety device ,
high pressure hose and trig-
ger gun.
The appliance is intended for
cleaning outdoors.
Appropriate ear protection
must be used.
Extension cables should be of
a watertight construction and
comply with the below-men-
tioned requirements for length
and cable dimensions.
to EN 1717. The backflow pre-
venter can be ordered under
number 106411177. The length
of the hose between the back-
flow preventer and the high
pressure washer must be at
least 10 metres to absorb pos-
sible pressure peaks (min diam-
eter ½ inch).
Operation by suction (for ex-
ample from a rainwater vessel)
is carried out without backflow
preventer. Recommended suc-
tion set: 126411387.
EN
1.0 mm² max.
1.5 mm² max.
2.5 mm² max.
12.5 m
20 m
30 m
If the electric cable is
damaged, it must be re-
placed by the manufacturer
or his service agent or simi-
larly qualified person in order
to avoid a hazard.
As soon as water has flown
through the BA valve, this water
is not considered to be drinking
water any more.
Mains power connection
IMPORTANT! Only use wa-
ter without any impurities. If
there is a risk of silt, sand or
sediment in the inlet water (i.e.
from your own well), an addi-
tional filter should be mounted.
The following should be ob-
served when connecting the
high pressure washer to the
electric installation:
Only connect the machine to
an installation with earth con-
nection.
The electric installation shall
be made by a certified elec-
trician.
It is strongly recommended
that the electric supply to this
machine should include a re-
sidual current device (GFCI).
Never use the machine in
an environment where there
could be a danger of explo-
sion. If any doubt arises,
please contact the local
authorities.
It is not allowed to clean
asbestos-containing surfaces
with high pressure.
Repair and maintenance
WARNING! Always remove the
electric plug from the socket be-
fore carrying out maintenance
work on the machine.
Safety devices
Locking device on spray handle
(7a) (see illustration at the end
of this manual):
This high pressure washer
must not be used at tempera- Water connection
The spray handle features a
locking device. When the button
is activated, the spray handle
cannot be operated.
tures below 0°C.
Connection to the public mains
Never let any persons stay
under the product when
stored on the wall.
according to regulations.
This high pres-
sure washer is
Thermal sensor:
WARNING!
only allowed to be
connected with
the drinking water
mains, when an appropriate
backflow preventer has been
installed, Type BA according
A thermal sensor protects the
motor against overloading. The
machine will restart after a few
minutes when the thermal sen-
sor has cooled.
Inadequate extension cables
can be dangerous. Cables on
reels should always be com-
pletely unwound to prevent the
cable from overheating.
Pressure safety device
An integrated hydraulic safety
valve protects the system from
excessive pressure.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
EN
2 Description
2.1 Application
This high-pressure washer has
been developed for domestic
use for cleaning:
Only use the high-pressure
washer for purposes described
in this manual.
- Car, motorbike, boat, cara-
van, trailer, patio/drive/flag-
The safety precautions must be
observed to prevent damage
stones, woodwork, brickwork, to the machine, the surface to
barbecue, garden furniture,
lawn mower
be cleaned or severe personal
injuries.
Section 5 describes the use of
the high-pressure washer for
vaious cleaning jobs.
2.2 Operation elements
and model survey
See illustration at the end of
this manual.
Specifications: See model tag
(15) of machine.
1 Start/stop switch
2 Water inlet (with filter)
3 High pressure connection
(only machines without
hose reel)
Sound pressure level measured
in accordance with ISO 3744
EEC directive 2000/14/EEC:
P 130.2:
4 High pressure hose
5 Electric cable
LpA = 80 dB(A), LWA = 90 dB(A)
P 150.2:
6 Spray lance
LpA = 80 dB(A), LWA = 93 dB(A)
P 160.2:
LpA = 80 dB(A), LWA = 95 dB(A).
7 Spray handle with lock (7a)
®
8 Tornado PR nozzle
®
9 Powerspeed nozzle
10 Detachable detergent con-
tainer
11 Nozzle cleaning tool
12 Dosing of detergents
13 Hose reel
Hand/arm vibrations measured
according to ISO 5349 below
2.5 m/s2.
We reserve the right to alter the
specifications.
14 Hose hook (only machines
without hose reel)
15 Model tag
16 Button for telescopic handle
17 Telescopic handle
18 Turnable cable hook
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
EN
3 Before you start using your
pressure washer
3.1 Mounting of holders for
spray lance
Mount the holders for spray
lance on the machine.
3.2 Mounting of hose hook
(only models without
hose reel)
Mount the hose hook (14) on
the handle (2 screws).
Note: the hose hook can be
mounted on the front as well as
on the back. Front position is to
be used if the product is used
together with a special wall
hook for wall storage.
3.3 Mounting of hose reel
handle (only models with
hose reel)
1. Click the hose reel handle
on to the trolley handle (no
screws).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
3.4 Mounting of quick
coupling
1. Screw the quick coupling
tight on to the water inlet (2).
Note: The inlet filter must al-
ways be fitted in the water inlet
pipe to filter out sand, limestone
and other impurities as these
will damage the pump valves.
EN
Caution: Failure
to fit the filter will
invalidate the
guarantee.
3.5 Mounting of high
pressure hose
Attach the high pressure hose
(4) to the spray handle (7).
Detach the high pressure hose
by pressing the pawl.
4 Operating your pressure washer
4.1 Connection of high pres-
sure hose
Machines without hose reel: At-
tach the high pressure hose (4)
to the high pressure connection
of the machine (3).
Only max. 7 m additional exten-
sion hose can be added.
Machines with hose reel: Un-
wind the high pressure hose
completely.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
4.2 Mounting of spray
lance and nozzles
EN
1. Push the spray lance (6) into
the spray handle (7) and twist
it until the bayonet coupling
locks into position.
2. Attach the nozzle.
4.3 Water connection
An ordinary 1/2" garden hose of IMPORTANT! Only use wa-
min. 10 m and max. 25 m will
be suitable.
ter without any impurities. If
there is a risk of silt, sand or
sediment in the inlet water (i.e.
from your own well), an addi-
tional filter should be mounted.
1. Let the water run through the
water hose before connecting
it to the machine to prevent
sand and dirt from penetrat-
ing the machine.
Note: Check
that the filter is
fitted in the water
inlet pipe and that it is clean
and free from debris.
NOTE: Connec-
tion to the public
mains according
to regulations.
2. Connect the water hose to
the water supply by means
of the quick connector (inlet
water, max. pressure: 10 bar,
max. temperature: 60°C).
3. Turn on the water.
4.4 Telescopic handle
The machine features a tele-
scopic handle. To raise or lower
the handle, press the button
(16) and move the handle up-
wards or downwards. When a
click is heard, the handle is in
right position.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
4.5 Start and stop of the ma-
chine (when connected
to a water supply)
The spray lance is affected
by a thrust during opera-
tion - therefore always hold it
firmly with both hands. IMPOR-
TANT: Point the nozzle at the
ground.
cleaned.
Do not cover the machine
during operation.
EN
Note: If the ma-
chine is left or not
used for 5 minutes, it must be
switched off on the start/stop
switch "O" (1):
1. Check that the machine is in
upright position.
NOTE: Do not place the ma-
chine in tall grass!
1. Turn the start/stop switch to
position "O".
2. Release the trigger lock.
3. Activate the trigger of the
spray handle and let the wa-
ter run until all air has es-
caped from the water hose.
4. Turn the start/stop switch (1)
to position "I".
2. Disconnect the electrical plug
from the socket.
3. Shut off the water supply and
activate the trigger to relieve
the machine of pressure.
4. Lock the spray handle.
5. Activate the trigger of the
When releasing the trigger of
the spray handle, the machine
automatically stops. The ma-
chine will start again when you
re-activate the spray handle.
spray handle.
Always adjust the distance and
thus the pressure of the nozzle
to the surface, which is to be
4.6 Start the machine (when
connected to open con-
tainers (suction mode))
The washer can take in water
from a rain water tank as an
example. The hose for the water
supply must not be too long,
approx. 5 m.
the machine. Place the entire
hose in a tank or bucket. To
avoid water spillage, crimp
the water inlet hose down in
the water and then connect
the hose to the machine with
the quick coupling and finally
uncrimp the water inlet hose.
2. Dismount spray handle,
lance and nozzle.
Make sure that the water tank is
not placed on a lower level than
the machine.
Use an external filter if the wa-
ter contains impurities.
3. Turn the start/stop switch to
position "I" and let the water
run, until the air has escaped
from the water hose and the
pump.
1. Make sure that the water
hose is filled completely with
water before connecting to
4. Mount spray handle, lance
and nozzle again.
4.7 Pressure regulation on
The pressure can be regulated
on the TORNADO PR nozzle.
®
®
the TORNADO PR-
nozzle
High pressure
Low pressure
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
4.8 Operation with detergents Application of detergents is
NOT possible if an extension
hose is applied.
4. Apply the detergent from
below and upwards.
5. Let the detergent act for the
time stated on the packing of
the detergent and flush with
pure water.
EN
1. Fill the container with a de-
tergent.
2. Mount the TORNADO® PR
nozzle and adjust it to low
pressure (see section 4.7).
3. Adjust the dosing regulator
(12) to the required volume
of detergent (0-5%).
Separate detergent container
1. Remove the cover with suc-
tion hose from the detergent
container.
2. Mount the cover with suction
hose on the separate deter-
gent container.
The cover has a standard thread
and fits common detergent con-
tainers. If your container does
not have a standard thread,
detach the filter from the suc-
tion hose and remove the cover.
Remount the filter in the suction
hose.
Extra detergent hose can be
pulled out of the machine.
4.9 Stationary use
If mounting a special wall hook
(not standard), the pressure
washer can be used as a sta-
tionary solution meaning that it
can be operated while hanging
on the wall.
a
b
Only mount the wall hook on a
sturdy wall. Adjust the length
of the screws and size of rawl-
plugs to the type of wall.
c
On the wall hook garden/rim
brush (a), brush (b) and noz-
zles (c) can be stored.
Important: The
bearing capacity of
the wall hook is
max. 30 kg.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
EN
5 Fields of application and working
methods
5.1 General
Efficient high presure cleaning is achieved by following a few
guidelines, combined with your own personal experience of spe-
cific cleaning tasks. Accessories and detergents, when correctly
chosen, can increase the efficiency of your pressure washer. Here
is some basic information about cleaning.
5.1.1 Detergent and foam
Foam or detergent should be applied onto dry surfaces so that
the chemical product is in direct contact with the dirt. Detergents
are applied from bottom to top, for example on a car bodywork, in
order to avoid "super clean" areas, where the detergent collects in
higher concentration and streams downwards. Let the detergent
work for several minutes before rinsing but never let it dry on the
surface being cleaned. Note: It is important that the detergents
do not dry up. Otherwise the surfac that has to be cleaned can be
damaged.
5.1.2 Mechanical effect
In order to break down tough layers of dirt, additional mechanical
effect may be required. Special wash brushes offer this supple-
mentary effect that cuts through dirt (especially by car washing).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
5.2 Typical fields of application
EN
Below you will find a description of a lot of cleaning tasks which can be solved by a pressure washer
from Nilfisk in association with accessories and detergents.
Task
Car
Accessories
Tornado® PR noz-
zle, auto brush,
Cleaning method
1. Apply Car Combi Cleaner. Always start from the bottom and
work upwards. Let Car Combi Cleaner act for at least 5 min.
underchassis spray 2. Wash the car with the Tornado® PR nozzle. Start at the front of
lance,
the car and work backwards to avoid water from penetrating by
the door mouldings.
Car Combi Cleaner 3. Use the brush for removal of traffic film which is not removed by the
nozzle. If the car is very dirty, apply Car Combi Cleaner again.
4. Attach the undercarriage spray lance and clean undercarriage
and wheel arches.
5. Remove water from the surface of the car with the squeegee
on the car brush. Make sure that all grains of sand etc. have
been removed before using the squeegee Wipe with a wash
leather where the squeegee cannot reach.
Rims, alu- Rim brush,
Apply Alu Cleaner with an automizer. Let it act for approx.
5 min. and wash with the rim brush. For steel rims, use Car Com-
bi Cleaner. Wash with rim brush.
minium
atomizer,
Alu Cleaner
Be careful! The high pressure jet may damage the tyres.
Flag-
stones,
concrete
floors and Cleaner,
other hard
Powerspeed®
nozzle,
Stone & Wood
Wash towards outlets or the like. On surfaces with moss or
algae you may start by applying Stone & Wood Cleaner. Wash
before the soap dries. Another more effective and quicker
method is to use the Patio Cleaner. Thus you will also avoid
splashes.
surfaces
Patio Cleaner
Garden
furniture,
wood
Wood Cleaner
Garden brush
Apply Wood Cleaner and wash before the soap dries.
NOTE: Use the garden brush to clean off the dirt.
Brickwork, Powerspeed®
Same method as for flagstones, but be careful - bad joints and
wood may be damaged by high pressure.You may choose only
to use the Tornado® nozzle. Adjust the distance (pressure) to the
quality of the joints and the wood. Patio Cleaner can also be used
on vertical surfaces.
Wood
work
nozzle,
Stone & Wood
Cleaner,
Patio Cleaner
Gutter
Underchassis spray Wash the gutter with the underchassis spray lance. Always wash
lance
towards down-pipes. Beware not to spray under the roofing.
Cleaning
of drain
pipes, out-
lets, down
pipes etc.
Tube cleaner
Push the tube cleaner approx. ½ m (to mark) into a tube or drain
and activate the trigger of the spray handle. The nozzle opening
turning backwards will pull the cleaner through the tube. The
nozzle will break down the „plug“ and flush the dirt backwards.
Rust, paint Water/sandblasting Mount the water/sand blasting equipment and rust and paint
equipment
is efficiently and quickly removed. Beware not to damage the
surface to be sandblasted.
Green-
house
Tornado® PR
nozzle, brush,
Stone & Wood
Cleaner
Wash with high pressure and maybe a brush.You may use Stone
& Wood Cleaner to remove moss and algae.
Garden
tools, lawn nozzle, Power-
mover
Tornado® PR
Rinse the worst dirt off with the Tornado® PR nozzle. Apply Metal
Cleaner and let it act for approx. 5 min. Wash with the nozzle.
speed® nozzle,
Metal Cleaner
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
EN
6 After using your pressure washer
6.1 Storing the washer
The machine should be sto-
red in a frost-free room!
5. Machines without hose reel:
Detach high pressure hose,
coil it up and place it on the
hose storage.
Pump, hose and accessories
should always be emptied of
water prior to storing as follows:
Machines with hose reel: Coil
the high pressure hose up on
the hose reel.
1. Stop the machine (turn the
start/stop switch (1) to posi-
tion “O” and detach water
hose and accessory.
2. Restart the machine and
activate the trigger. Let the
machine run until no more
water runs through the spray
handle.
6. Place spray handle, nozzles
and other accessories in the
holders of the machine.
Should the machine by mistake
be frozen, it will be necessary
to check it for damage.
NEVER START-UP A FROZEN
3. Stop the machine and un-
plug. Wind the electric cable
round the hooks placed on
the side of the machine.
4. Separate spray handle and
high pressure hose.
MACHINE.
Frost damages are not
covered by the guarantee!
6.2 Winding up of electric
cable and high pressure
hose
To avoid accidents, the electric
cable and the high pressure
hose should always be wound
up carefully.
1. Wind up the electric cable on
the appropriate hooks. Built-
in clip for good holding.
The lower hook can be
turned to release the electric
cable.
2. The high pressure washer
comes in two models: A) with
hook for storage of high pres-
sure hose (14) - B) with a
hose reel (13).
6.3 Storage of accessories
The standard accessories
(spray handle, spray lance,
nozzles and nozzle cleaning
tool) can be stored on the pres-
sure washer.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
EN
7 Maintenance
WARNING! Always disconnect
Clean the connectors of dust
and sand.
Clean the nozzles.
the electrical plug from the
socket prior to maintenance or
cleaning.
To ensure a long and problem
free working life, please take
the following advice:
Any repair should always be
made in an authorized work-
shop with original spare parts.
Wash off water hose, high
pressure hose, spray lance
and accessories before
mounting.
7.1 Cleaning of water inlet
filter
Clean the water inlet filter regu-
larly once a month or more fre-
quently according to use. Care-
fully loosen the filter with a pair
of pliers and clean it. Check that
it is intact before re-mounting it.
The inlet filter must always be
fitted inside the water inlet pipe
to filter out sand, limestone and
other impurities, as they will
damage the pump valves.
CAUTION: Failure to fit the filter
will invalidate the guarantee.
7.2 Cleaning of nozzle
A clogging up in the nozzle
causes a pump pressure which
is too high. This is why cleaning
is required immediately.
1. Stop the machine and dis-
connect the nozzle.
2. Clean the nozzle. IMPOR-
TANT: The cleaning tool (11)
should only be used when
the nozzle is detached!
3. Flush the nozzle backwards
with water.
7.3 Cleaning of machine
vents
The machine should be kept
clean so as to let cooling air
pass freely through the ma-
chine vents.
7.4 Greasing of couplings
To ensure easy connection and couplings should be greased
that o-rings do not dry up, the regularly.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
EN
8 Trouble-shooting
Please ensure that you check the following before contacting the Nilfisk service organization:
Symptom
Cause
Recommended action
Machine refuses to start Machine not plugged in
Defective socket
Plug in machine.
Try another socket.
Replace fuse. Switch off other machines.
Try without the extension cable.
Fuse has blown
Defective extension cable
Fluctuating pressure
Pump sucking air
Check that hoses and connections are air-
tight.
Valves dirty, worn out
or stuck
Pump seals worn out
Clean and replace or refer to local Nilfisk
distributor
Clean and replace or refer to local Nilfisk
distributor.
Motor busses
Machine stops
Low voltage or
low temperature
Activate the trigger of the spray handle.
Fuse has blown
Incorrect mains voltage
Replace fuse. Switch off other machines.
Check that the mains voltage corresponds
to specification on the model tag.
Leave the washer for 5 minutes to cool
down.
Thermal sensor activated
Nozzle partially blocked
Fuse too small
Clean the nozzle (see section 7.2)
Fuse blows
Change to an installation higher than the
amp. consumption of the machine.
You may try without the extension cable.
Machine pulsating
Air in inlet hose/pump
Allow machine to run with open trigger until
regular working pressure resumes.
Check that the water supply corresponds to
specifications required (see model tag)
NB! Avoid using long, thin hoses (min. 1/2")
Clean the nozzle (see section 7.2)
Clean the filter (see section 7.1)
Inadequate supply of
mains water
Nozzle partially blocked
Water filter blocked
Hose kinked
Straighten out hose.
Machine often starts
and stops by itself
Pump/spray handle is
leaking
Contact your nearest Nilfisk Service
Centre.
Machine starts, but
no water comes out
Pump/hoses or accessory Wait for pump/hoses or accessory to thaw.
frozen
No water supply
Water filter blocked
Nozzle blocked
Connect inlet water.
Clean the filter (see section 7.1)
Clean the nozzle (see section 7.2)
In case problems other than the above occur, please contact your local Nilfisk distributor.
UK:
Customer Services at Penrith - 01768 868995
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
EN
9 Further information
9.1 Recycling the washer
Make the old cleaner unusable
immediately.
tive 2002/96/EC on old electri-
cal and electronic appliances,
used electrical goods must
be collected separately and
recycled ecologically.
1. Unplug the cleaner and cut
the electric cable.
Do not discard electrical appli-
ances with household waste.
Contact your local authorities or
your nearest dealer for further
information.
As specified in European Direc-
9.2 Warranty conditions
Nilfisk guarantees high pres-
sure washers for domestic use
for 2 years. If your high pres-
sure washer or accessories are
handed in for repair, a copy of
the receipt must be enclosed.
Guarantee repairs are being
made on the following condi-
tions:
Repairs under this guarantee
include replacement of defec-
tive parts, exclusive of packing
and postage/carriage. Besides,
we refer to your national law of
sale.
The machine should be for-
warded to one of the service
centres of the Nilfisk organisa-
tion with description/specifi ca-
tion of the fault.
that defects are attributable
to flaws or defects in materi-
als or workmanship. (wear
and tear as well as misuse
are not covered by the guar-
antee).
Repairs not covered by the
guarantee conditions will be
that the directions of this
instruction manual have been invoiced. (I.e. malfunctions due
thoroughly observed.
that repair has not been car-
ried out or attempted by oth-
er than Nilfisk-trained service
staff.
to Causes mentioned in section
Troubleshooting Chart of the
instruction manual).
that only original accessories
have been applied.
that the product has not been
exposed to abuse such as
knocks, bumps or frost.
that only water without any
impurities has been used.
that the high pressure wash-
er has not been used for
rental nor used commercially
in any other way.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
9.3 Accessories
EN
Only use original accessories.
Brush
For cars and other surfaces.
Extension hose
7 m extension hose increasing the working range.
Special spray lance for washing your car underneath.
Underchassis
spray lance
Drain & Tube
cleaner
15 m long tube cleaner for the cleaning of tubes and drains.
Water-sand-
blasting equip-
ment
For removal of paint and rust. Sand available from do-it-your-
self shops.
Patio Plus
Equipment for quick cleaning of patio/drive/flagstones.
Garden brush
Rim brush
Wall hook
Rotating brush for cleaning of wooden surfaces.
Rotating brush for cleaning of wheel rims.
For suspension of your high pressure washer on the wall.
Water suction
kit
For removal of large amounts of water from e.g. garden
pounds.
Rotary brush
Roof cleaner
For cleaning vehicles and other surfaces.
For removal of coatings on roofs, walls, greenhouses, etc.
With optional brush for cleaning of caravans, trailers, windows,
etc.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Nilfisk P 130.2 / P 150.2 / P 160.2
Detergents
EN
Stone & Wood Cleaner
Plastic Cleaner
For flagstones, brick- and woodwork. Suitable for moss and algae.
For plastic and synthetic materials such as garden furniture.
For cleaning of metal such as garden tools.
Metal Cleaner
Car Combi Cleaner
Alu Cleaner
For cars etc. With rinsing wax.
For surfaces of aluminium. Applied with an atomizer.
Oil & Grease Cleaner
For cleaning of grease and oil on motors for instance. Applied with
an atomizer.
Wood Cleaner
Roof Cleaner
For cleaning of wooden surfaces incl. of wooden garden furniture.
For removal of coatings on roofs, walls, greenhouses, etc.
10 EU Declaration of Conformity
EU Declaration of Conformity
Product:
Type:
High Pressure Washer
Nilfisk P 150.2, P 160.2
Nilfisk P 130.2 X-TRA, P 150.2 X-TRA, P160.2 X-TRA
Description:
230 V 1~, 50 Hz - IP X5
The design of the unit corresponds to the
following pertinent regulations:
EC Machine Directive
EC Low-voltage Directive
EC EMV Directive
2006/42/EC
2006/95/EC
2004/108/EC
Applied harmonised standards:
EN ISO 12100-1 (2004), EN ISO 12100-2 (2004)
EN 60335-2-79 (2006)
EN 55014-1 (2006), EN 55014-2 (2001), EN 61000-3-2 (2006)
Applied national standards and technical
specifications:
BS EN 60335-2-79
Nilfisk
Division of Nilfisk-Advance A/S
Industrivej 1
DK-9560 Hadsund
Anton Sørensen
General Manager, Technical Operations EAPC Hadsund, 01.07.2010
18
Download from Www.Somanuals.com. All Manuals Search And Download.
7
7a
6
9
8
4
14
13
11
16
1
5
12
10
3
15
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|