Niles Audio Radio RFG User Manual

I N S T A L L A T I O N G U I D E

RADIO FREQUENCY GATEWAY

RFG

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

The Niles RFG Radio Frequency Gateway is a highly ﬂexible tool that allows system

designers to add a ZigBee^®radio transmitter/receiver to Niles MultiZone products or extend

the Radio Frequency Receiver of a Niles HT-MSU Home Theater Main System Unit.

FEATURES AND BENEFITS

MULTI-MODE SET-UP DIPSWITCHES

The RFG has two dipswitches that are set to choose one of the four operation modes:

Master Base, Repeater Base, Wireless Keypad and Not Assigned. The mode is determined

by the system design.

INSTALLATION FLEXIBILITY

With a low proﬁle design, easy access connections, and wall-mount hole wings, the RFG can

be wall mounted behind system components or attached to a baseboard. The high-impact

plastic housing is heat resistant, so the RFG can also be mounted in an attic to a crossbeam.

System and Keypad connections allows multiple RFGs to be cascade-wired over a single

CAT-5 wire run.

RELIABLE ZIGBEE RF COMMUNICATION

The RFG uses a reliable ZigBee based 2.4 Gigahertz radio frequency that works well even in

“noisy” RF environments. The RFG has a 16-channel and 16-network ID capability that allows

multiple RFGs to be used near each other and in multiple-dwelling units like condos.

RFG EX Model has 10 channels.

NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373

Download from Www.Somanuals.com. All Manuals Search And Download.

QUICK AND EASY SET-UP WITH WIZARD-BASED NILES

QUICKCONFIG^TMCONFIGURATION SOFTWARE

An RFG can be added to any network based Niles MultiZone Receiver or home system theater

using the Niles QuickConﬁg System Conﬁguration Software. The QuickConﬁg‘ software is

wizard-based and guides the installer/programmer through basic and advanced system designs.

Conﬁguration is stored in non-volatile memory within the RFG. This safeguards against

accidental loss of programming for the entire life of the product.

CONTENTS

Check that your RFG Radio Frequency Gateway contains the following:

• RFG (Radio Frequency Gateway)

• Ferrite Bead

PARTS GUIDE

(UNDERNEATH)

RFG

��

�

Download from Www.Somanuals.com. All Manuals Search And Download.

1) Power LED - The blue LED indicates that the RFG has power. This LED also indicates

the connection status to the Niles MultiZone Receiver or Home Theater Main System Unit.

2) System Connection -This RJ-45 connection is used when the RFG is connected

to a Niles MultiZone receiver.

3) Keypad Connection - This RJ-45 connection is used when the RFG is connected

to a keypad, a Niles HT-MSU Home Theater Main System Unit, or to continue the CAT-5

cable run to other RFGs.

4) Power Connection - This barrel type jack is where the power supply connects

to the RFG. A Niles FG01035 Power Supply (optional) is required for certain system

conﬁgurations. The ferrite bead is used on the end of the power plug connected to the RFG.

5) Mounting Wings - The RFG can be conveniently mounted to a baseboard, wooden

stud, or directly to the wall. (mounting screws not included).

6) Set-up Dipswitches - These switches allow the RFG to be conﬁgured for one of

four operation modes: Master Base, Repeater Base, Wireless Keypad, and Not Assigned.

SYSTEM DESIGN CONSIDERATIONS

The Niles RFG Radio Frequency Gateway is a highly ﬂexible tool that allows system

designers to add a ZigBee radio transmitter/receiver to Niles MultiZone products or extend

the Radio Frequency receiver of the Niles HT-MSU Home Theater Main System Unit.

Multiple RFGs are used to create a RF mesh network. RF mesh networks require at least

a transmitter and a receiver, however in large installations repeater bases can be used.

NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373

Download from Www.Somanuals.com. All Manuals Search And Download.

ZIGBEE TERMINOLOGY

To understand how to use the RFG, the system designer needs to understand

ZigBee terminology.

MASTER BASE

The Master Base is the coordinator of the RF mesh network. Its job is to receive

information from the Repeater Bases and End-Points in the system, consolidate that

information, and provide it to the main controlled source. The Master Base is like a head

coach in football. His job is to listen to the assistant coaches and players to create and

send the game plan to those that execute it. The Master Base should be located centrally

and as high as possible within the system design. A Master Base is hard-wired to the

main controlled source, the MultiZone receiver, or iC2 Main System Unit.

END-POINT

The End-Point is where the RF transmitted information starts and stops. For the RFG,

the End-Point is typically a MultiZone system keypad. A system design can have multiple

End-Points (keypads). End-Points can be spread over a large area and communicate

directly to the Master Base, or through a Repeater Base to the Master Base. By its nature

an End-Point will not repeat RF information to other End-Points.

REPEATER BASE

The job of a Repeater Base is to listen for any network RF information, take that

information and re-transmit it so that other bases can pick it up if they are too far away

for direct communication.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZIGBEE RF NETWORK

When designing an RF network it is important to know that at least one Master Base

and one End-Point are needed. Repeater bases are used to expand the coverage area

of the RF network. Multiple hops can be used in a RF network design, however great

care should be used to not exceed more than four hops. To count the hops, start from an

end-point, and then add one for each Repeater Base used between the End-Point and the

Master Base. See Figure 1 for basic RF network system design.

Figure 1. Basic RF Network

��

NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373

Download from Www.Somanuals.com. All Manuals Search And Download.

RFG USAGE WITH NILES NETWORK-BASED MULTIZONE RECEIVERS

The RFG can be used with Niles Network-based MultiZone receivers allowing the installer to

create “wireless keypads.” Typically, control keypads are connected to the MultiZone receiver

via a CAT-5 cable. In installations that do not allow a run of CAT-5 cable (such as a retroﬁt

or a detached area from the main equipment area), use the RFG to overcome the hard-wired

limitation. The dipswitches pre-conﬁgure each RFG to the application for which it is being

used. See Setting the Dipswitches section.

RFG USAGE WITH A NILES iC2 HOME THEATER

AUTOMATION & CONTROL SYSTEM

The Niles iC2 uses RF communication between the iC2 Tabletop Controller and the Home

Theater Main System Unit (HT-MSU). In other words, there is a Master Base built inside of

the HT-MSU and the iC2 remote is an End-Point. The HT-MSU is typically located behind the

home theater gear in an equipment rack. That is usually the worst place for the Master Base

to be located due to the metal and noise (interference) created by the home theater sources.

One RFG can be use to replace and extend the built-in Master Base to an area where there

will be little or no interference. The RFG is hard-wired to the HT-MSU using CAT-5 cable

terminated with RJ-45 plugs. Please see the Installation Section for proper termination wiring.

SETTING THE DIPSWITCHES

The two dipswitches on the RFG allow for it to be pre-conﬁgured to one of the four modes:

1) MASTER BASE

2) REPEATER BASE

3) WIRELESS KEYPAD (END-POINT)

4) NOT ASSIGNED

Download from Www.Somanuals.com. All Manuals Search And Download.

SYSTEM DESIGN WIRING FOR RFG

The RFG has two RJ-45 connections for wiring into the system. The connection used

depends on the mode and overall system design.

A MASTER RFG CONNECTED TO A NILES NETWORK-BASED MULTIZONE RECEIVER:

A RFG with dipswitches set for Master Base mode must be connected directly to the

MultiZone receiver using CAT-5 cable as detailed in Figure 2. No power supply is needed.

Figure 2. A master RFG connected to a MultiZone receiver

��

Niles Network Based

Set as

CAT-5 Cable

MultiZone Receiver

Master Base

A master RFG can be wired with repeater RFGs by wiring the CAT-5 cable from the

MultiZone Receiver’s Communications port to the System connection of the ﬁrst RFG, and

then from the ﬁrst RFG’s Keypad connection port to the System connection of the next RFG.

Two RFGs can be daisy chained to the receiver without an additional power supply. A Niles

Power supply (FG01035) can be used to power up to four RFGs on a single CAT-5 cable run.

Figure 3. Daisy-chain wiring and powering of 3 RFGs

CAT-5 Cable

��

Keypad

Connection

Niles Network Based

MultiZone Receiver

System

Connection

Repeater

Base

Repeater

Base

Master

Base

NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373

Download from Www.Somanuals.com. All Manuals Search And Download.

A REPEATER RFG NOT WIRED TO A MULTIZONE RECEIVER

A RFG set for Repeater Base Mode and not connected to a MultiZone receiver (stand

alone) must have an optional power supply connected.

Figure 4. RFG wired as a stand

alone repeater

��

RFG

A RFG SET FOR WIRELESS KEYPAD MODE

A RFG set for Wireless Keypad must have the optional power supply and a CAT-5 cable

connected to the keypad.

Figure 5. RFG in wireless keypad conﬁguration

��

RFG

Keypad

Port

A RFG EXTENDING THE RADIO OF THE NILES HT-MSU

The RFG dipswitches should be set for Master Base mode and an optional power supply

must be used. Connect from the HT-MSU Expansion port to the RFG’s Keypad connection

(Figure 6). See more detail in HT-MSU manual, available online at www.nilesaudio.com).

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 6. RFG extending the radio of a HT-MSU

CAT-5 Cable

��

HT-MSU

RFG

Keypad

Port

INSTALLATION CONSIDERATIONS

PLACEMENT OF THE RFG

Niles recommends placing the RFG along a baseboard or in an attic. Generally, the unit

should be placed in a concealed location because its indicator and connections are

only used during installation. Placement possibilities include:

1) Baseboard (affixed to the back of the equipment

cabinet or a nearby wall)

2) Attic (attached to a ceiling joist)

Figure 7. Wall mount placement.

Use Sheetrock Screws

NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373

Download from Www.Somanuals.com. All Manuals Search And Download.

ANTENNA CONSIDERATIONS

Communication between RFGs is RF-based with a frequency of 2.4 Gigahertz.

Effective range of communication is 75 feet (22.86 meters) in open air. The RF antenna

is internal to the RFG and its orientation is shown by the “molded radio wave symbol”

on the front of the RFG. The RFG and its antenna should be vertical for best reception.

Figure 8. RFG vertical antenna orientation

molded radio

wave symbol

��

WIRING CONSIDERATIONS

The RFG requires two different types of wires run, based on set-up and system design:

1) CAT-5 CABLE

A CAT-5 cable is used to connect the RFG to either the MultiZone receiver

or to a keypad. This cable must be terminated with RJ45 connectors using

T568A protocol as shown in the Installation Section.

2) POWER CABLE

A power supply is needed when the RFG is set-up as an independent

Repeater Base or Wireless Keypad. A Niles FG01035 Power Supply (sold

separately) is used and connected using the barrel connector.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

1) SET THE RF MODE DIPSWITCHES (Figure 9)

2) CONNECT CAT-5 CABLE

Connection to a MultiZone receiver or a keypad uses CAT-5 cable terminated with

RJ45 connection plugs. The CAT-5 cable must be terminated using the T568A

standard wiring (Figure 10).

Figure 10. T568A wire termination

Figure 9. Repeater Base Dipswitch setting

1 = GREEN/WHITE

2 = GREEN

��

3 = ORANGE/WHITE

4 = BLUE

5 = BLUE/WHITE

6 = ORANGE

��

Dipswitches

7 = BROWN/WHITE

8 = BROWN

��

3) CONNECT POWER SUPPLY PER RFG SET-UP

Based on the mode of the RFG, a Niles Power Supply maybe needed (see System

Considerations section to see if optional power supply is needed).

4) MOUNT THE RFG (see Figure 7)

5) SET RF COMMUNICATION CHANNEL

After the RFG has been mounted and all connections made, the RF channel must

be set if the RFG is being used in a wireless keypad mode. The RF channel can be

set by accessing the installer settings mode of the keypad (please see Niles Keypad

manual for information on this menu).

NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

The set-up dipswitches allow the RFG to be pre-conﬁgured for its role in the system RF

mode design. With this in mind, troubleshooting the RFG comes down to two main issues:

1) SET-UP ISSUES

2) HARDWARE ISSUES

SET-UP ISSUES

PROBLEM:

1. Wrong Set-up

If the RFG is set-up for the wrong operation mode, the system will not operate

properly. The symptoms could include: Power LED flickers or is off, intermittent

operation, or no operation.

SOLUTIONS:

• Check the dipswitch settings

• If set for wireless keypad mode, check the RF channel by accessing through

the keypads installer settings mode

• If dipswitches are set for Not Assigned mode, the RFG must be configured

using the Niles QuickConfig software

HARDWARE ISSUES

There are two basic issues that can prevent proper operation of the RFG.

These issues are presented in the order of probability.

Download from Www.Somanuals.com. All Manuals Search And Download.

PROBLEM:

1. Bad Connections or Wiring

If the connections or wiring are wrong, loose, shorted, or open, the system will

not operate properly. The symptoms could include: Power LED flickers or is off,

intermittent operation or no operation.

SOLUTIONS:

• Test your power supply connections

• Test your CAT-5 cable for shorts and opens

PROBLEM:

2. RF or Electromagnetic Interference

Digital sources, poorly shielded sources, microwave ovens, cordless telephones,

cell phones, high definition television sets, light dimming controls and other

sources of electromagnetic fields can induce radio frequency noise and interfere

with your radio frequency gateway. The symptoms could include: Blue LED on

RFG continuously flickering or poor range, intermittent operation or no operation.

SOLUTIONS:

• Move your RFG to a new mounting location

• Change the RF Channel the RFG is communicating on

NOTE: THERE ARE ZIGBEE “SNIFFING” TOOLS AVAILABLE ON THE MARKET THAT ALLOW

AN INSTALLER TO SEE RF CHANNEL USAGE BY WI-FI AND OTHER ZIGBEE DEVICES

NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSORIES OF THE RFG

1.25A 12VDC UNIVERSAL POWER SUPPLY

FG01035

Current outlet provides 12V DC sync connection via an accessory

cable to the HT-MSU

IC2 HOME THEATER AUTOMATION AND CONTROL SYSTEM

�

FG01342

��

�

��

�

��

�

��

�

��

�

��

�

��

Home theater automation and control system that includes table top

remote control, main system unit, two power supplies, master key labels,

ZigBee Antenna and Extension Kit

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

Power Requirements: 12VDC from either connection to Niles Network based MultiZone

receiver or optional Niles power supply (FG01035)

Unit Dimensions: 4.68" L x 2.15" W x 1.15" H

11.89 cm x 5.46cm x 2.92cm

RF Section: 2.4-GHz frequency ZigBee wireless mesh technology

Signal Range: 75 to 100 feet open air

(22.86 meters to 30.48 meters)

Wiring Requirements: CAT-5 cable

Shipping Weight: 1 lb.

Warranty: Two-year limited

NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

Niles Audio Corporation (“NILES”) warrants to the original retail purchaser only that this product will be free of manufacturing defects in material and workmanship for the following

periods and subject to the limitations and exclusions set forth below:

Lifetime Warranty

All Passive Loudspeaker Products (those not requiring AC or battery power).

Ten years from the date of purchase

All Other Passive Products (those not requiring AC or battery power).

Two years from the date of purchase

All Active Products (those requiring AC or battery power).

This warranty is not transferable to subsequent purchasers of the product. To obtain warranty service, contact the authorized dealer where you purchased your product or take

the unit to the nearest authorized NILES dealer (with proof of purchase – claims made without proof of purchase will be denied) who will test the product and if necessary, forward

it to NILES for service. If there are no authorized NILES dealers in your area, you must contact NILES to receive a factory Return Authorization Number. DO NOT RETURN ANY UNIT

WITHOUT FIRST RECEIVING WRITTEN AUTHORIZATION AND SHIPPING INSTRUCTIONS FROM NILES.

Upon examination, NILES will, at its sole option and expense, repair or replace any product found to be defective. NILES will return the repaired or replaced unit to you via its usual

shipping method from the factory to your address in the United States of America or Canada only. Any shipping costs for addresses outside of the United States or Canada shall be

the responsibility of the purchaser. In the event that this model is no longer available and cannot be repaired effectively, NILES, at its sole option, may replace it with a different model

of equal or greater value, or refund the original purchase price paid. THE FOREGOING ARE YOUR EXCLUSIVE REMEDIES FOR BREACH OF WARRANTY.

This Warranty does not include service or parts to repair damage caused by improper use or handling, including but not limited to damage caused by accident, mishandling, improper

installation, commercial use, abuse, negligence, or normal wear and tear, or any defect caused by repair to the product by anyone other than NILES.

This warranty does not cover reimbursement for your costs of removing and transporting the product for warranty service evaluation, or installation of any replacement product

provided under this warranty.

This Warranty will be void if:

• the Serial Number on the product has been removed, tampered with or defaced.

• the product was not purchased from an authorized dealer or reseller.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES. NILES EXPRESSLY DISCLAIMS ALL SUCH OTHER

WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT, WITH

RESPECT TO THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY LAW, NILES SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES

EXCEPT TO THE EXTENT PROVIDED (OR PROHIBITED) BY APPLICABLE LAW, EVEN IF NILES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Notwithstanding the above, if you qualify as a “consumer” under the Magnuson-Moss Warranty Act, or applicable state laws, then you may be entitled to any implied warranties

allowed by law for the Warranty Period. Further, some states do not allow limitations on how long an implied warranty lasts or allow the exclusion or limitation of consequential

damages, so such limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

For the name of your nearest authorized NILES dealer, contact: NILES AUDIO CORPORATION, P.O. BOX 160818, Miami, Florida 33116-0818, or call 1-800-289-4434, 1-305-238-

4373. Please be advised that NILES only sells its products via the Internet through a select group of authorized Internet dealers. These are listed on our website at www.nilesaudio.

com. Products offered on the Internet through unauthorized Internet dealers are not covered by the NILES warranty and may be either:

1) goods acquired on a secondary or grey market

2) counterfeit or stolen goods

3) damaged, or defective goods

ATTENTION: TO OUR VALUED CONSUMERS:

To insure that consumers obtain quality pre-sale and after-sale support and service, NILES products are sold exclusively through authorized dealers. This warranty is VOID if the

products have been purchased from an unauthorized dealer.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY REGISTRATION CARD

Model Purchased__________________________________ Serial Number _________________________________

Date Purchased (month/day/year)______________________ Dealer Name and Location ________________________

Dr.

Name ____________________________________ Address ____________________________________________

City_______________________________State__________Zip ___________ Tel ( ) ________________

Miss

Mr.

Mrs.

Ms.

Please take a moment to ﬁll out our warranty registration card. The information helps us to get to know you better and develop the

products you want

Age:

Musical tastes: (Please check

What magazines do you read?

1. ________________

Do you . . . ?

Under 25

Own a House. If yes,

how many square feet?

_________________

all that apply)

Alternative

Classical

Country

Jazz

25-34

2. ________________

3. ________________

35-44

45-54

55 & over

Own a Town House/

Condominium/Co-op

Rent an Apartment

Rent a House

Who will install the product?

Custom Installer

Electrician

Friend

Myself

New Age

Popular

R&B

Income:

Under $24,999

$25,000-$34,999

$35,000-$44,999

$45,000-$59,999

$60,000-$74,999

$75,000-$99,999

Over $99,999

Rock

Are you interested in receiving

literature on other Niles products?

Yes

Other _____________

Which factor(s) influenced the

purchase of your Niles product?

(Please check all that apply)

Ease of Use

Price/Value

Product Features

Quality/Durability

Reputation

Style/Appearance

Warranty

How did you hear about Niles?

Architect/Developer

Custom Installer

Direct Mail

Are there products/capabilities that

you would like to see introduced?

Occupation:

Friend/Family

Arts/Entertainment

Business Owner

Engineer

_________________________

In-Store Display

Interior Designer

Magazine Ad

Finance/Accounting

General Office

Management

Professional

Sales/Marketing

Student

Tradesperson

Mail-Order Catalog

Newspaper Ad

Product Brochure

Product Review

Retail Salesperson

NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373

Download from Www.Somanuals.com. All Manuals Search And Download.

BL E N D I N G HI G H FI D E L I T Y AN D AR C H I T E C T U R E

N i l e s A u d i o C o r p o r a t i o n

1 2 3 3 1 S . W . 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3 1 8 6

1 - 3 0 5 - 2 3 8 - 4 3 7 3

1 - 8 0 0 - B U Y - H I F I

–

w w w . n i l e s a u d i o . c o m

Blending High Fidelity and Architecture are registered trademarks of Niles Audio Corporation.

All other trademarks are the property of their respective owners. DS00585B

Download from Www.Somanuals.com. All Manuals Search And Download.

Miller Electric Welder XL AC DC User Manual
MTD Log Splitter 249 620 003 User Manual
NEC Telephone 2014 User Manual
Network Technologies Switch ST C5KVM 600 CE User Manual
Nokia Headphones BH 208 User Manual
Olympus DVR VN 1100 User Manual
Omega Vehicle Security Calculator DPC10 CS User Manual
Panasonic Answering Machine KC TCC942 B User Manual
Panasonic Electric Shaver ES3831 User Manual
Panasonic Power Hammer EY6803 User Manual