Nikon DVR DX TL5716E User Manual

DIGITAL RECORDER

USER’S MANUAL

MODEL

DX-TL5716E

THIS INSTRUCTION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL RECORDER.

Download from Www.Somanuals.com. All Manuals Search And Download.

Caution and care

HEAVY OBJECTS SHOULD NEVER BE PLACED ON THE UNIT (E.G., MONITOR)

NEVER TOUCH OR INSERT ANY OBJECT INSIDE THE UNIT

Touching the inside of the cabinet or inserting foreign objects of any kind through the disc loading slot or ventilation holes not

only creates a safety hazard but can also cause extensive damage.

PROTECT THE POWER CORD

Damage to the power cord may cause ﬁre or shock hazard. If the power cord is damaged, turn OFF the MAIN switch and

carefully unplug the cord by holding the main plug.

If this unit is moved with the power on status, the built-in HDD may be damaged. Conﬁrm that more than one minute have

passed since the power cord and the connecting cords were disconnected, then move this unit. Make sure to take the disc

out and close the disc loading slot.

UNPLUG THE POWER CORD DURING A LONG ABSENCE

Turn off the power and unplug the power cord during a long absence.

MAINTAIN GOOD VENTILATION

Do not obstruct the many ventilation holes on the unit. For maximum ventilation, leave some space around the unit and place

the unit on a hard level surface only, and ensure it is not covered during use. Heavy objects should never be placed on the

unit.

WHEN NOT IN USE

When not in use, always eject the disc and turn OFF the MAIN switch.

CABINET CARE

Never use petroleum-based cleaners. Clean with a soft cloth moistened with soap and water and wipe dry.

PVC cables or leads should not be left in contact with the cabinet surface for long periods.

INSTALLATION LOCATION

For excellent performance and lasting reliability install in a location that is:-

1. Well ventilated, out of direct sunlight and away from direct heat.

2. A solid vibration-free surface.

3. Free from high humidity, excessive dust and away from magnetic ﬁelds.

4. Please ensure that the ventilation fan located on the unit’s back panel is not blocked.

UNSUITABLE LOCATIONS

Placing the unit in the following places might shorten the product life:

•

Extremely cold places, such as refrigerated warehouses and ice houses

Places where excessive hydrogen sulﬁde is likely to be generated, such as hot-springs areas

Places or locations with salt air environment.

THIS EQUIPMENT DOES NOT PROVIDE CONNECTION FOR USED WITH OUTDOOR OR CABLE DISTRIBUTION

SYSTEMS.

NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

DO NOT PLACE HEAVY OBJECT ON THIS UNIT.

DO NOT STEP ONTO THIS UNIT.

DO NOT PLACE ANY OBJECTS IN FRONT OF THE DISC LOADING SLOT.

The unit may drop or fall by losing its balance. It may cause injury or failure of the unit.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

THIS APPARATUS MUST BE GROUNDED.

MAINS LEAD CONNECTION

The mains lead on this Unit is ﬁtted with a non-rewireable mains plug, incorporating a 5A fuse. If you need to replace

the fuse, use a 5A fuse approved by BSI or ASTA to BS 1362, ensuring you reﬁt the fuse cover. If the mains plug is not

suitable for the sockets in your home, and you require to remove the plug, remove the fuse, cut off the plug then dispose

of the plug immediately, to avoid a possible electric shock hazard. To reﬁt a new plug, follow these instructions; Green-

and-yellow: Earth, Blue: Neutral and Brown: Live. As the colours in the mains lead of this Unit may not correspond with

the coloured markings identifying the terminals in your plug, proceed as follows.

•

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the

letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured

black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

This unit complies with the requirements of the EC Directive 2004/108/EC, “EMC Directive” and 2006/95/EC, “Low

Voltage Directive”. The requirements for the susceptibility according to EN 55024 and the requirements for interference

according to EN 55022 are observed for the operation on residential areas, business, light industrial premises and

in small scale enterprises, inside as well as outside of the building. All places of operation are characterised by their

connection to the public low voltage power supply system. This unit is manufactured in accordance with EN 60950-1.

Beginning

Download from Www.Somanuals.com. All Manuals Search And Download.

Caution and care (continued)

Warning

This is a class A product. In a domestic environment this product may cause radio interference in which case the user

may be required to take adequate measures.

Note: This symbol mark is for EU countries only.

This symbol mark is according to the directive 2002/96/EC Article 10 Information for users and Annex IV,

and/or to the directive 2006/66/EC Article 20 Information for end-users and Annex II.

Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which

can be recycled and/or reused.

This symbol means that electrical and electronic equipment, batteries and accumulators, at their end-of-life, should be

disposed of separately from your household waste.

If a chemical symbol is printed beneath the symbol shown above, this chemical symbol means that the battery or

accumulator contains a heavy metal at a certain concentration. This will be indicated as follows:

Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%)

In the European Union there are separate collection systems for used electrical and electronic products, batteries and

accumulators.

Please, dispose of this equipment, batteries and accumulators correctly at your local community waste collection/

recycling centre.

Please, help us to conserve the environment we live in!

About the hard disk drive (HDD)

• This unit is equipped with HDD, which is a very delicate device. Therefore, handle this unit carefully.

• Don't expose this unit to vibrations and shocks. It may be damaged when exposed to vibrations and shocks especially

during power-on or access to the HDD.

• Don't unplug the power cord during recording/playback or power-on.

• This unit is equipped with a system that automatically resumes and continues recording in the event of a minor failure

in the HDD or other components during recording. However, depending on the type of a failure in the HDD, this unit

may not able to continue recording. For early detection of failures, it is recommended to have this unit inspected every

year.

• In the event of a fault in the HDD, replace it immediately. For replacement of the HDD, please contact your Mitsubishi

dealer. (To replace the HDD, it is required to stop recording.)

• Use recommended HDD only. For HDD supported by this unit, please contact your Mitsubishi dealer.

• When the HDD is replaced, the recorded data are deleted. To ensure stable operation of this unit, the ﬁrmware may be

updated from time to time. The recorded data may be deleted in such a case.

• When you dispose of or transfer this unit, handle the video data stored in HDD carefully and take all responsibilities

related to the disposal or transfer.

• In the event of a failure in the HDD during normal recording or mirroring, this unit may not be able to resume recording

after rebooted, depending on the failure condition.

• When you enable the mirroring function while the recorded data are stored in the HDD, the recorded data are deleted.

• When you delete the data, the recorded images cannot be played back any more.

• It is recommended to check regularly that the recorded data are played back correctly.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation location and handling

• Before you ﬁrst use this unit, supply power to it for at least 48 hours to charge the built-in backup battery so that the

built-in power compensator circuit can be activated. When the battery isn't charged sufﬁciently, the built-in clock may

go wrong or the unit may not able to recover in case of a power failure.

• Don't plug this unit and high current devices (such as copier and air conditioning) into the same wall socket.

• Place this unit on a level and stable surface. When it is used on an unstable surface, a failure may be caused.

• Don't remove the outer covering of this unit.

• Don't place this unit close to other devices. They may interfere with each other, disturbing video and audio.

• Don't place this unit on a heat source. In addition, don't place this unit near a heat source because this unit has

ventilation openings in its sides and bottom. Otherwise the inside temperature may rise, causing a failure.

• When this unit is placed on or under the monitor, a failure may be caused, such as image disturbance and DVD/CD

disc ejection failure.

• Don't place a strong magnetic object near this unit. It may affect the images adversely and cause loss of recorded

data.

• Don't expose this unit to volatile substances such as insecticide or don't leave this unit in contact with rubber or plastic

products for a long time. Otherwise the surface of the product may deteriorate or the coating may come off.

• When this unit is placed directly on the waxed ﬂoor, the adhesion may increase between the ﬂoor and the non-slip

rubber pads on the bottom of the product, causing the ﬂoor coating to come off or be colored.

• The HDD and cooling fans are motor-driven parts. To ensure stable recording, it is recommended to replace them

every 30,000 hours of use as a guide assuming that the ambient operating temperature is 25°C. When replacing HDD,

also replace the vibration-proof rubbers at the screwed areas. (Note that this period is just for a guide of replacement

interval and isn't intended to guarantee the lifetime of the parts. They may be broken earlier because of shocks applied

to the product and ambient operating temperature.)

• Be sure to use this unit within the allowable ambient temperature range (5° to 40°C) and humidity range (80% or less).

When you use the unit out of this temperature range, the internal parts may be adversely affected or a malfunction may

occur. In addition, when the temperature rises high, the characteristics of the HDD may deteriorate or its lifetime may

be shortened. When you use the unit in a low temperature environment, supply it with power for at least 10 minutes

before use.

• Don't put your hand into the tray ejection opening. Your hand may be caught in by the tray, causing injury. If your hand

should be caught in, don't try to pull it out forcefully. Turn the power off ﬁrst, unplug the power cord, and contact your

Mitsubishi dealer.

• Clean the product regularly to prevent the ventilation openings from being covered by dust.

Precautions for rack-mounting

• When mounting this unit in a rack, ensure that the temperature inside the rack doesn't rise to 40°C or higher. When

installing a rack, you are recommended to install fans to keep the temperature inside the rack 30°C or lower.

• Don't install a device that becomes hot under this unit. Otherwise the inside temperature may rise, causing a failure.

• Don't give a shock to all HDD devices in the rack.

• Before taking this unit in or out of the rack, be sure to turn off HDD devices being energized in the rack.

• Don't place this unit near a device that generates vibrations.

Beginning

Download from Www.Somanuals.com. All Manuals Search And Download.

Caution and care (continued)

Changing installation location

• When moving this unit, be sure to turn off the MAIN switch, make sure that the unit is completely stopped, and then

unplug the power cord. When this unit is exposed to excessive shock while being energized, the internal electronic

parts or HDD may be damaged. Be careful especially while the power indicator or access indicator is blinking.

• Don't move this unit for at least one minute after you turn off the power. Even after the power is turned off, the disc

in the HDD keeps rotating by inertia for a while and the head is in an unstable state. This unit in such state is more

vulnerable to vibrations and shocks than while being energized. Be careful not to give this unit even a slight shock for

at least one minute after turning off the power. Wait at least one minute for the disc to stop, and then you can move the

product.

• When moving this unit, cover it with shock absorbers to prevent shocks to the inside.

• When placing this unit on a ﬂoor, lay it gently on a soft mat or cloth.

Maintenance

• Gently wipe dirt off the cabinet with a soft cloth.

• When dirt persists, clean it off using a cloth soaked in water-diluted neutral detergent and wrung well and then wipe

dry.

• When using a chemical cleaning cloth, follow its instructions.

• Don't use solvent such as benzene and thinner. Otherwise the surface of the product may deteriorate or the coating

may come off.

Notes for constructing a surveillance system using this unit

• This unit can be controlled by external devices via the external connector, RS-232C connector, or LAN connector. In

addition, external devices can be controlled via the external connector, RS422/485 connector, or RS-232C connector.

These functions allow this unit to ﬂexibly support an advanced security system. However, depending on the settings

of this unit or connection or combination with external devices, this unit or externally connected devices may operate

wrongly, causing adverse effects on the entire surveillance system.

• When constructing a surveillance system using this unit, you are recommended to check its operation by connecting or

combining it with other devices in advance.

• Don't use the alarm function of this unit for the purpose of making serious decisions or for applications involving human

lives.

• When this unit becomes unable to recognize an external device in recording because of a power failure, voltage drop,

or other failure, the recording point may move to the HDD inside this unit or other HDD. To prevent such symptom, it is

recommended to use an uninterrupted power supply or other similar device.

• When you unplug the power cord or turn off the breaker during recording, the HDD may be broken or recorded data

may become unable to be played back. When you turn on and off the breaker every day, program the timer recording

to be performed while the breaker is on and don't turn off the breaker during recording.

• When the user or any third party uses external devices wrongly, or external devices are affected by electric noise or

they are damaged or repaired, the saved data may be lost. Mitsubishi doesn't take any responsibility for damages

related to such data loss.

• By connecting external HDDs to this unit, you can expand the memory or use them as a copy device. However, when

you perform recording, playback, or copy at a high rate using this unit, recording or playback data dropout or other

failure may occur depending on the connected device because of slow data transfer or slow response. Be sure to

check for such failure before starting the practical operation of the unit.

• Don't use the function to control the powers of external devices using the bus power of this unit.

• External devices you want to use may not be suitable for the intended application of this unit. For details, you are

recommended to contact your Mitsubishi dealer.

• When connecting external devices, be sure to secure the connected cables using the supplied clamp bands. When the

cables are disconnected or not connected ﬁrmly, the system may become unstable or images may not be recorded.

• Don't disconnect the cables while this unit is running. Otherwise a failure may be caused.

Download from Www.Somanuals.com. All Manuals Search And Download.

For important recordings

• Be sure to perform test recording before starting the practical operation of this unit, and also check regularly that the

recording is performed correctly according to the settings during the practical operation.

• Mitsubishi doesn't compensate for data not recorded or not played back correctly because of a failure occurring in this

unit or connected devices during the use of this unit.

• As a preparation for unexpected breakdown or accident, you are recommended to make regular backups of important

recordings. Though digital signals don't deteriorate, playback or recording may become impossible because of aging

deterioration of discs depending on the storage conditions.

About DVD/CD discs

• Don't use cracked discs, deformed discs, and discs repaired with adhesive. It may break up and scatter around during

the use, causing breakdown or injury.

• When you hold the disc, don't touch the recording surface.

• When condensation occurs on the disc, wipe the moisture off the disc surface before use. Dirt on the disc surface such

as ﬁngerprints and dust may deteriorate the picture and audio quality. Gently wipe it off from the center toward the

edge of the DVD/CD disc using a soft cloth. Don't use solvent such as benzene and thinner, record cleaner, and anti-

static agents. Otherwise the disc is damaged.

• When dirt persists, clean it off using a cloth soaked in water-diluted neutral detergent and wrung well and then wipe

dry.

• Don't use the following discs. Those discs may break or a failure may occur in the unit. (Recording or playback may

not be performed correctly.)

• Discs on which paper slips or stickers are placed, or scratched discs.

• Discs from which labels are peeled off or on which excessive adhesive is present.

• Cracked discs, deformed discs, or discs repaired with adhesive.

• After using discs, store them in their cases. Don't store discs in the following places:

• Place where they are exposed to direct sunlight.

• Place where there is much dust.

• Place where the temperature and humidity are high.

• You cannot play DVD video discs that are commercially available or recorded with home DVD recorders. Only data

recorded on this unit can be played back.

• Don't use discs used by a personal computer or other recorder or those used for unsuccessful copying or interrupted

copying due to a power failure because they may cause malfunction. (Data recorded halfway may not be played back.)

When copying to a CD-RW or DVD-RW disc is not done successfully, clear the data and then retry.

• With the special PC viewing/communication software, you can play data copied to a DVD or CD using this unit.

However, it is not guaranteed that they can be played by all types of personal computer or DVD/CD drive.

• Mitsubishi doesn't compensate for data not recorded, copied, or played correctly because of a failure occurring in this

unit or DVD/CD disc.

• DVD-R/-RW discs may not be recorded or played depending on their characteristics and conditions.

• When discs are broken, data recorded on them cannot be recovered.

Beginning

Download from Www.Somanuals.com. All Manuals Search And Download.

Caution and care (continued)

Maintenance of DVD drive (laser pickup)

• Dust or dirt on the recording/playback lens causes image disturbance and sound skipping, making it impossible to

perform recording or playback correctly. Ask your Mitsubishi dealer for cleaning.

Don't use commercially available lens cleaning discs because they may damage the lens.

• The DVD drive may be prone to have an error in recording or playback when its operating time for recording and

playback exceeds 1000 hours.

CLASS 1 LASER PRODUCT

• This unit records data digitally. Therefore, exercise caution in recording video images protected by copyright.

Recording time and product warranty

• Estimated recording time displayed on the menu screen is a continuous recordable time calculated in terms of the

functional operation, not a product warranty period. In addition, they are not a warranty period of the operational

reliability of the parts and components used in the unit.

Motion detection function

• Motion detection function in this unit may malfunction depending on the input condition of the video signal. If you

connect this unit to a system that issues an alarm using the motion detection function, take care to avoid such

malfunction. When the motion detection function malfunctions, connect another sensor to the ALARM IN terminal on

the rear of this unit.

Supplied power cord

• The supplied power cord is designed for this unit only. Don't use this cord for other products.

Download from Www.Somanuals.com. All Manuals Search And Download.

Network

• It is recommended to conﬁrm with your network administrator about the network settings in advance.

• As this unit is operated through network, you may suffer from damage as follows.

(1) Leakage or drain of information through this unit.

(2) Unauthorized operation of this unit by malicious third parties.

(3) Disturbance or deactivation of this unit by malicious third parties.

To prevent damage listed above, take sufﬁcient network security measures on your own responsibility.

• Set a network password that cannot be easily guessed by third parties. In addition, change the password regularly.

Disclaimer

• Mitsubishi assumes no responsibility or makes no compensation for operation error of your surveillance system, loss

of recorded data, or other damages or losses due to a failure in this unit. In no event will Mitsubishi repair, restore, or

reproduce recorded data.

• In no event will Mitsubishi assume responsibility or liability for the following:

(1) Disassembly, repair, or alteration of this unit by the user or installer.

(2) Failure or breakdown in or damage to this unit resulting from misuse or careless handling by the user or installer.

(3) Inconvenience or damages resulting from inability to display or record images or to operate the unit's functions

correctly due to any reason or cause including breakdown or failure in this unit.

(4) Failure in this unit due to combination with other equipment manufactured by a third party, or inconvenience or

damages resulting from such failure.

(5) Inconvenience, damages, or claims arising out of breakdown in this unit or loss of recorded video data due to

replacement of the built-in HDD by the user or installer.

(6) Inconvenience or damages arising out of breakdown in this unit or inability to display or record images due to

natural disaster including earthquake and storm.

(7) Inconvenience, damages, or claims arising out of breakdown in the built-in HDD or loss of recorded video data due

to impact or vibration or environmental factors such as temperature at the installation site.

(8) Demand for damages or claim of infringement of privacy on the ground that the video monitored or recorded by

the user become public or are used for any purpose other than surveillance for whatever reason.

(9) Incidental, special, or consequential damages arising directly or indirectly related to this unit.

(10)Failure caused by any program created based on the command data provided by Mitsubishi, or inconvenience,

damages, or losses resulting from such failure.

• This unit is intended for recording and playback of video monitored by cameras. Mitsubishi doesn't assure that this unit

is capable of preventing crimes.

Beginning

Download from Www.Somanuals.com. All Manuals Search And Download.

Note

Open source software

Thank you for purchasing Mitsubishi digital recorder DX-TL5716E (hereinafter referred to as “Product”). Before using this

Product, please be sure to read the following Software License Agreement with regard to the software contained in this

Product (hereinafter referred to as “Licensed Software”). By using this Product, you are agreeing to be bound by the

terms and conditions of the following Software License Agreement.

This Product contains software programs that are covered by GNU General Public License or GNU Lesser General Public

License. Such software programs are excluded from Licensed Software and not covered by the following Software License

Agreement. For the terms and conditions for use of the software programs covered by GNU General Public License or GNU

Lesser General Public License, please see “Notice about software to which GNU GPL/LGPL is applied”*.

In addition, this Product contains “Apache” and “OpenSSL (including “Original SSLeay” library).” These software programs

are also excluded from Licensed Software and not covered by the following Software License Agreement. For the terms and

conditions for use of these software programs, please see “Notice about Apache software”* and “Notice about OpenSSL soft-

ware”*.

Other open source software contained in this product is excluded from Licensed Software and not covered by the following

Software License Agreement. For the terms and conditions for use of these software programs, please see “Notice about

other open source software”*.

The documents of “Notice about software to which GNU GPL/LGPL is applied,” “Notice about Apache software,” “Notice

about OpenSSL software,” and “Notice about other open source software” are contained (in the format of electronic

files as notice_GPL_LGPL_ja.pdf, notice_Apache_ja.pdf, notice_OpenSSL_ja.pdf, and notice_other_ja.pdf) in the

“OpenSoft_License” folder in the CD supplied with this Product.

MPEG-4 patent

This Product is licensed under the MPEG-4 pool license only for the purpose of personal and non-commercial use involving

the following activities:

(1) Encoding video in compliance with the MPEG-4 visual standard ("MPEG-4 Video").

(2) Decoding MPEG-4 Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or

was obtained from a video provider licensed by MPEG LA to provide MPEG-4 Video. For more information, visit http://

www.mpegla.com.

(3) Playback of video recorded by the recorder using a personal computer in which the PC viewing/communication software

or the OCX software for Web browser is installed, or playback of video recorded by the recorder using a Web browser.

Download from Www.Somanuals.com. All Manuals Search And Download.

Software License Agreement

This Software License Agreement (“Agreement”) is an agreement between you (“User”) and Mitsubishi Electric Corporation

(“Licensor”) with regard to the license to use Licensed Software.

Article 1 (Grant of license)

Licensor hereby grants to User a nonexclusive, nontransferable license to use Licensed Software.

Article 2 (License)

1. The license to use Licensed Software granted hereunder shall mean the User’s right to use Licensed Software sole-

ly on this Product. User is hereby allowed to refer to the descriptions and instructions related to Licensed Software

contained in the user’s guide of this Product to the extent necessary for use of such Licensed Software.

2. User shall not reproduce, copy, or modify, in whole or in part, or make addition or alteration to Licensed Software

and pertinent documents.

3. User shall use Licensed Software in accordance with the operating instructions described in the user’s guide.

Article 3 (License conditions)

1. User shall not transfer to any third party the license stipulated in the preceding article.

2. User shall not disassemble, decompile, or otherwise analyze the source code of Licensed Software.

Article 4 (Ownership of Licensed Software)

All and any rights including copyrights related to Licensed Software and pertinent documents shall be owned by

Licensor or the original right holder who granted to Licensor the right to sublicense Licensed Software (hereinafter

referred to as “Original Right Holder”). User shall not own any rights other than the license granted hereunder with

regard to Licensed Software and pertinent documents.

Article 5 (Disclaimer)

Licensor and Original Right Holder shall make no warranties whatsoever with regard to Licensed Software and have

no liability for any damages suffered by User or any third party arising out of User’s execution of the license granted

hereunder, except in cases where any applicable laws are extended.

Article 6 (Responsibility toward third party)

Any issues related to intellectual property rights, including but not limited to rights of privacy, copyright, and patent,

involving any third party arising out of User’s use of Licensed Software shall be settled by User on its own responsi-

bility, and Licensor shall have no responsibilities for such issues.

Article 7 (Conﬁdentiality)

User shall keep secret the details of Licensed Software and pertinent documents provided hereunder and the con-

tents of this Agreement that are unknown publicly and shall not disclose or leak such details and contents to any

third party without consent of Licensor.

Article 8 (Termination)

In case of either of the following events, Licensor may terminate this Agreement immediately and may claim against

User for resulting damages it suffers.

(1) User’s violation of any provision of this Agreement.

(2) Occurrence of ﬁling against User for seizure, provisional seizure, provisional injunction, or other forcible execu-

tion.

Article 9 (Disposal of Licensed Software)

If this Agreement is terminated pursuant to the preceding article, User shall dispose of Licensed Software, pertinent

documents, and any copies thereof in its possession within two weeks after termination hereof and shall provide Li-

censor with a written certiﬁcation of such disposal.

Article 10 (Update of Licensed Software)

If User updates Licensed Software using an update CD supplied or sold by Licensor or any other means, this Agree-

ment shall remain applicable to the updated version of such Licensed Software, unless Licensor provides additional

separate terms and conditions for using the updated version of such Licensed Software.

Article 11 (Miscellaneous)

1. If any provision of this Agreement is determined to be invalid by law, the remaining provisions hereof shall remain

valid and enforceable.

2. If any doubt arises in relation to matters not deﬁned herein or interpretation hereof, Licensor and User shall discuss

such doubt and attain a solution in a faithful manner.

Beginning

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the built-in clock

Left-click the mouse to display <Main menu>.

You can display <Main menu> also by pressing the

SET UP button on the front panel.

Select “Setup” to display the <Setup> screen.

Setup

Select “Setting” next to “Clock and language

Setup

Clock and language setting

Setting

setting” to display the <Clock and language>

screen.

Click on each of day, month, year, hour,

Clock and language

minute, and second until the desired value

appears.

Clock setting (SNTP is active)

Set

20 08

Present time zone

GMT

Setting

Click “Set.”

Day light saving setting

Language setting

Auto

Set

Select [Setting] next to [Present time zone].

ENGLISH

<Zone setting of time> screen appears.

E:Return

Set the time zone depending on the location of

the recorder and then select [Set].

After ﬁnishing the setting, select [Return] to return to

the screen of step 4.

Set the day light saving setting.

“Auto”: Automatically adjusts the clock according

to the settings. For the detailed settings, select “Set”

and then use the [In] area to set the time and date for

advancing the clock and [Out] area for putting back

the clock.

“Off”: Auto day light saving function is not used.

Close the menus.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing back recorded images

Press the PLAY button on the front panel.

You can play back images even during recording.

Press the PAUSE button to pause playback.

(Still image playback)

Press the STOP button to stop playback.

Notice

•

When you change the multiplexer, playback direction, or playback speed during playback, a black screen may be displayed.

When you change the multiplexer or the playback-related settings during playback, or when you play back data where

recording status was changed due to change of recording operation, a black screen may be displayed or image dropout may

occur.

•

This recorder uses the motion picture compression format. Due to this, the recorder may take time to display the playback

picture.

Tips

•

After the power is turned on, playback starts from the oldest recorded data. Otherwise, playback starts from the point where it

was stopped last time.

When the PAUSE/JUMP TO END button is pressed while the playback is stopped, images around the end of the latest

recorded data are played back in the still image playback mode.

•

To resume playback during still image playback, press the PAUSE or PLAY button.

When you press the camera number button during still image playback in the single screen mode, the image from the camera

corresponding to the button you pressed is displayed.

Convenient function

Selecting the device or audio to be played back

Press the SET UP button on the front panel or left-click the mouse to display <Main menu>.

Change the playback device while playback is stopped.

Select “Device selection” to display the <Change audio and play device> screen.

Under “Play device selection,” select the button of the device you want to play back. (You cannot select devices that are not

set.)

“HDD (Normal)” : Plays back the data in the normal recording area.

“HDD (Alarm)” : Plays back the data in the alarm recording area.

“HDD (Emergency)” : Plays back the data in the emergency recording area.

“HDD (Preliminary)” : Plays back the pre-alarm or pre-emergency recording data.

“HDD (Copy)” : Plays back the data in the copy device.

“HDD (Archive)” : Plays back the data in the archive device.

“DVD/CD” : Plays back the data on a DVD/CD disc.

“USB memory” : Plays back the data in a USB memory device.

When you change the playback device on the <Change audio and play device> screen and then start playback with that

screen being displayed, data in the device that was selected before the change are played. Before starting playback, close

the screen.

Under “Audio channel selection,” select the button of the audio you want to output.

The audio setting made here is reﬂected to both the live display and playback.

“Audio A1” : Outputs the audio A1.

“Audio A2” : Outputs the audio A2.

“Off” : No audio is output.

Operations

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing the screen mode to display images from cameras

You can change the screen mode to display images on the monitor.

Displaying images in the single screen mode

Press the button of the camera you

want to display.

Camera number

buttons

Displaying images in the split screen mode

* The numbers shown in the figures indicate the

factory-default camera number display positions.

Press the 4-split button.

4-split a

4-split b

Each time you press the button, the

screen mode changes in the order of

4-split a 4-split b 4-split c

4-split d 4-split a

…

4-split c

4-split d

4-split button

9-split button

10-split button

13-split button

16-split button

Press the 9-split button.

9-split a

9-split b

10 11

13 14

Each time you press the button, the

screen mode changes in the order of

9-split a 9-split b 9-split a

…

Press the 10-split button.

10-split a

10-split b

Each time you press the button, the

screen mode changes in the order of

10-split a 10-split b 10-split a

…

10 11 12

13 14 15 16

Press the 13-split button.

13-split a

13-split b

Each time you press the button, the

screen mode changes in the order of

13-split a 13-split b 13-split a

…

10 11 12 13

13 14 15 16

Press the 16-split button.

16-split

10 11 12

13 14 15 16

Download from Www.Somanuals.com. All Manuals Search And Download.

Notice

You cannot switch the screen mode while the menu screen is displayed. To switch the screen mode, close the menu screen

ﬁrst and then press the camera number button or a split button.

•

Tips

To set the camera number to be displayed in each screen mode, use <Multiplexer setting> in the <Setup> menu. You can set

the camera number to be displayed differently for each of output A and output B.

Convenient function

Changing the screen mode using the mouse (single screen mode)

Right-click the mouse.

Right-click

The mouse operation screen is displayed.

Click the single screen button to display the camera number buttons.

Click the button of the camera you want to display.

Changing the screen mode using the mouse (split screen mode)

Right-click the mouse.

Right-click

The mouse operation screen is displayed.

Click the button of the split screen mode you want to display.

Operations

Download from Www.Somanuals.com. All Manuals Search And Download.

Searching for the desired image

You can search for images by specifying the recording date and time.

Press the SEARCH button on the front panel to

display <Search menu>.

Click the device name under “Play device” (for

Search menu

12-01-2008 Sat

13:35:17

example, HDD (Emergency)) until the desired

device name appears.

Play device

HDD (Emergency)

Start : 01-01-2008 09:24:31

Execute search

You cannot select devices that are not set.

End : 11-11-2008 02:50:08

Execute search

Camera filter

Click the camera number under “Camera filter”

until the desired number appears.

Time and date

20 08

Alarm list search

MD search

Click on each of day, month, year, hour, minute,

E:Exit

and second until the desired value appears.

Click “Search.”

The image recorded on the specified date and time is

displayed on the quarter screen. (Playback pause)

Press the

button to start playback.

In addition to the time and date search, you can search for images using the following methods.

For the detailed operating procedures, see the Installation Manual.

For searching data in the HDD (Preliminary), you can use time date search only.

Search menu

12-01-2008 Sat

Play device

13:35:17

HDD (Emergency)

Start : 01-01-2008 09:24:31

Execute search

Start point search

This function searches for the

Alarm list search

End : 11-11-2008 02:50:08

Execute search

This function searches for images using

the list of times and dates when alarm

recording and emergency recording

started.

oldest recorded data.

Camera filter

End point search

This function searches for the

latest recording data.

Time and date

20 08

Alarm list search

MD search

This function searches for images from

a camera that detected motion.

E:Exit

Download from Www.Somanuals.com. All Manuals Search And Download.

Convenient function

Displaying <Search menu> using the mouse

Right-click the mouse.

The mouse operation screen is displayed.

Click the

button to expand the menu.

Click the Search button ( ).

<Search menu> is displayed.

Specifying the search time using the calendar

Click “Time and date” of <Search menu>.

Set the search start time

Hour

01/2008

The <Set the search start time> screen is displayed.

SunMon Tue Wed Thu Fri Sat

10 11

Click on each of year and month until the desired value appears.

The calendar of the selected year and month appears.

10 11 12

12 13 14 15 16 17

18 19 20 21 22 23

13 14 15 16 17 18 19

20 21 22 23 24 25 26

27 28 29 30 31

Minute

Click “Check data” to check whether the selected device has

recording data or not. Dates having recording data are displayed in

gray and dates without recording data are displayed in black.

00 05 10 15 20 25

30 35 40 45 50 55

Check data

Search start time

01-01-2008 10 : 30 : 00

E:Quit

D:Execute

Click the date to be searched.

Click the hour and minute to be searched.

Click “Execute.”

The date and time speciﬁed in steps 2 to 4 are set as the search start time and then <Search menu> reappears.

Playing back the retrieved image using the buttons on the front panel

Playback starts when the PLAY or PAUSE button is pressed.

Playback stops when the STOP button is pressed.

Changing the playback speed or display size of the retrieved image using the mouse

You can change the playback speed or display size using the buttons on the search result screen.

Search menu

Each time you click this button, the display size of the search result screen changes.

Images recorded in the quarter picture size cannot be displayed on the full screen.

Each time you click this button, the reverse playback speed changes in the order of

approx. X2 approx. X4 approx. X8 approx. X16 Fast playback approx. X2.

Reverse frame-by-frame playback starts.

01-01-2008 Sat

Play device

13:35:17

HDD (Emergency)

01-01-2008 09:24:31

Execute search

11-11-2008 02:50:08

Start

End

Execute search

Camera filter

Time and date

20 08

Alarm list search

E:Exit

MD search

Reverse playback starts.

Playback/reverse playback stops.

Playback/reverse playback pauses.

Playback starts.

Frame-by-frame playback starts.

Each time you click this button, the playback speed changes in the order of approx. X2

approx. X4 approx. X8 approx. X16 Fast playback approx. X2.

Operations

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying recorded images

You can copy the still image being displayed to a USB memory device or DVD/CD disc as a still or moving image (one-touch copy).

This function is convenient to copy recording data for a short period of time.

Set a USB memory or a DVD/CD disc in the

recorder.

The recorder automatically detects the copy destination

device. When both a USB memory device and DVD/CD

disc are detected, the DVD/CD disc is used as the copy

destination device.

Display the image you want to copy in the still

image playback mode and the single screen

mode.

See

page 14 for the single screen mode.

page 13 for the still image playback mode.

Press the COPY button on the front panel to

display <Copy menu>.

Select the image to be copied from “Moving

image” or “Still image.”

Copy menu

One touch copy

Camera

1ch

“Moving image”: Copies data for the speciﬁed recording

Copied data

Moving image

Still image

duration starting from the image being displayed.

Start

: 07-07-2008 13:25:08

5 Min

Duration

“Still image”: Copies 1 GOP including the still image

Execute copy

being displayed.

Copy starts also by pressing [COPY].

Other copy

Setting

When “Moving image” is selected in step 4, click

the time next to “Duration” until the desired copy