“This appliance is intended for supplemental heating.”
“This heater shall not be installed in a bedroom or
bathroom.”
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SAFETY INFORMATION........................................................................................... 1
AIR FOR COMBUSTION AND VENTILATION................................................... 3
INSTALLATION / CLEARANCES ............................................................................. 6
STOVE CAVITY ASSEMBLY................................................................................... 7
INSTALLATION: MODEL (MA C100BATLP OR MA C100BATNAT) BURNER
BASE.............................................................................................................................. 9
POSITIONING OF LOGS........................................................................................... 10
INSTALLATION: MODEL BVFBX201 (MA CVF200LP OR MA CVF200NAT)
FIRE BOX.................................................................................................................... 11
INSTALLATION: OPTIONAL BLOWER ASSEMBLY .......................................... 13
CONNECTING TO GAS SUPPLY............................................................................. 14
LIGHTING INSTRUCTIONS (SIT) MILLIVOLT .................................................... 17
CLEANING.................................................................................................................. 19
TROUBLE SHOOTING.............................................................................................. 20
ACCESSORIES ........................................................................................................... 23
REPLACEMENT PARTS ........................................................................................... 24
WIRING DIAGRAM................................................................................................... 33
WARRANTY............................................................................................................... 34
Download from Www.Somanuals.com. All Manuals Search And Download.
IDENTIFICATION NUMBERS AND DESCRIPTIONS FOR
CAST STOVE SERIES
HEPPLEWHITE CAST UNIT:
ID #
DESCRIPTION
ALMOND
BLACK
CVF100A
CVF100B
CVF100BP
CVF100G
CVF100GP
CVF100R
CAST (BLACK PAINT)
GREEN
CAST (GREEN PAINT)
RED
TOWNSEND II CAST UNIT
ID#___________________________ DESCRIPTION
CVF200A
CVF200B
CVF200BP
CVF200G
CVF200GP
CVF200R
ALMOND
BLACK
CAST (BLACK PAINT)
GREEN
CAST (GREEN PAINT)
RED
BURNER BASE UNITS FOR HEPPLEWHITE CAST UNIT ONLY:
ID#
DESCRIPTION
LIQUID PROPANE
NATURAL
MA C100BATLP
MA C100BATNAT
BURNER BASE (VENTLESS FIREBOX) UNITS FOR TOWNSEND II ONLY:
ID#
CVFB200LP
CVFB200NAT
DESCRIPTION
LIQUID PROPANE
NATURAL
OPTIONAL BLOWER ASSEMBLY FOR (VENTLESS FIREBOX) TOWNSEND II
ONLY:
ID#
DESCRIPTION
MA CVF714
BLOWER ASSEMBLY
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE NATURAL OR L.P GAS STOVE HEATER
6. During initial operation, slight
smoking could occur due to
heater burning manufacturing
residues.
SAFETY
INFORMATION
7. To prevent the creation of soot,
follow the instructions in
“Cleaning and Maintenance”,
page 19.
8. Before using furniture polish,
wax, carpet cleaners, or similar
products, turn heater off. If heated,
the vapors from these products
may create a white powder residue
within burner box or on adjacent
walls or furniture.
9. This heater has an Oxygen
Depletion Sensing (ODS) safety
shutoff system. The ODS shuts
down the heater if not enough
fresh air is available. See “Air for
Combustion and Ventilation”,
pages 3 through 5. If heater keeps
shutting off, see “Trouble-
shooting”, pages 20 through 22.
10. Do not run heater
WARNINGS
:
Carbon Monoxide Poisoning:
Early signs of carbon monoxide
poisoning resemble the flu, with
headaches, dizziness, or nausea.
If you have these signs, the heater
may not be working properly.
Get fresh air at once! Have
heater serviced. Some people are
more affected by carbon
monoxide than others. These
include pregnant women, people
with heart or lung disease or
anemia, those under the influence
of alcohol, and those at high
altitudes.
•
where flammable liquids or vapors
are used or stored
under dusty conditions
•
11. Do not use this stove to cook food
or burn paper or other objects.
12. Do not use heater if any part has
been exposed to or under water.
1. This appliance is only for use
with the type of gas indicated on
the rating plate. This appliance is
not convertible for use with other
gases.
Immediately call
a
qualified
service technician to inspect the
room heater and to replace any
part of the control system and any
gas control which has been under
water.
Make certain you read and
understand all Warnings. Keep
this manual for reference. It is
your guide to safe and proper
operation of this heater.
2. If you smell gas
•
•
•
shut off gas supply
do not try to light any appliance
do not touch any electrical
switch: do not use any phone in
your building
13. Do not operate heater if any log is
broken.
14. Turn heater off and let cool before
servicing. Only a qualified service
person should service and repair
heater.
15. Operating heater above elevations
of 4,500 feet could cause pilot
outage.
16. Do not place stove directly on
carpeting, vinyl tile, or any
combustible material other than
wood. The stove must set on a
metal or wood panel extending the
full width and depth of the
appliance.
•
•
immediately call your gas
supplier from a neighbor’s phone.
Follow the gas supplier’s
instructions
if you cannot reach your gas
supplier, call the fire department
3. This heater shall not be installed
in a bedroom or bathroom.
4. Do not use this stove as a wood
burning fireplace. Use only
models MA C100BATLP, MA
C 1 0 0 B A T N A T ,
M A
C V F B 2 0 0 L P , o r M A
CVFB200NAT series vent-free
gas log heater.
5. Do not add extra logs or
ornaments such as pine cones,
vermiculite, or rock wool. Using
these added items can cause
sooting.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT
INDENTIFICATION
PRODUCT FEATURES
MODELS MA C100BATLP, MA C100BATNAT OR
MA CVFB200LP, MA CVFB200NAT MILLIVOLT LOG
HEATER UNITS WITH CVF100’s AND CVF200’s CAST
STOVE SERIES.
OPERATION
This heater is clean burning. It requires
no outside venting. There is no heat
loss out a vent or up a chimney. Heat is
generated by realistic, dancing yellow
flames. This heater is designed for vent
-free operation. State and local codes
in some areas prohibit the use of vent-
free heaters.
SAFETY PILOT
This heater has a pilot with an Oxygen
Depletion Sensing (ODS) safety
shutoff system. The ODS/pilot is a
required feature for vent-free room
heaters. The ODS/pilot shuts off the
heater if there is not enough fresh air.
STOVE
BODY
PIEZO IGNITION SYSTEM
This heater has a piezo ignitor. This
system requires no matches, batteries,
or other sources to light heater.
OPTIONAL
VALVE CONTROL
KNOB
AUTO
OFF
MANUAL
REMOTE CONTROL
BRACKET
STOVE DOOR
(SHOWN IN THE OPEN
POSITION)
PRESSURE ADJUSTMENT
(FLAME) KNOB
PIEZO IGNITOR
FIGURE 1– TYPICAL STOVE CABINET MODEL
LOCAL CODES
Install and use heater with care. Follow all local codes. In the absence of local codes, use the
latest edition of “The National Fuel Gas Code ANSI Z223.1”, also know as NFPA 54*.
*Available from:
American National Standards Institute Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
2
Download from Www.Somanuals.com. All Manuals Search And Download.
PROVIDING ADEQUATE
VENTILATION
Confined and Unconfined Space
AIR FOR
COMBUSTION AND
VENTILATION
The National Fuel Gas Code, ANSI
Z223.1 defines a confined space as a
space whose volume is less than 50
cubic feet per 1,000 Btu per hour (4.8
m3 per kw) of the aggregate input
rating of all appliances installed in that
space; and unconfined space as a
space whose volume is not less than 50
cubic feet per 1,000 Btu per hour (4.8
m3 per kw) of the aggregate input
rating of all appliances installed in that
space. Rooms communicating directly
with the space in which the appliances
are installed*, through openings not
furnished with doors, are considered a
part of the unconfined space.
The following are excerpts from
National Fuel Gas Code, NFPA 54/
ANSI Z223.1, Section 5.3, Air for
Combustion and Ventilation.
All spaces in homes fall into one of
the three following ventilation
classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 4 through 5
will help you classify your space and
provide adequate ventilation.
Unusually Tight Construction
This heater shall not be installed in a
confined space or unusually tight
construction unless provisions are
provided for adequate combustion and
ventilation air.
The air that leaks around doors and
windows may provide enough fresh
air for combustion and ventilation.
However, in buildings of unusually
tight construction, you must provide
additional fresh air.
Today’s homes are built more energy effi-
cient than ever. New materials, increased
insulation, and new construction methods
help reduce heat loss in homes. Home
owners weather strip and caulk around
windows and doors to keep the cold air
out and the warm air in. During heating
months, home owners want their homes as
airtight as possible.
*Adjoining rooms are communicating
only if there are doorless passageways
or ventilation grills between them.
Unusually tight construction is
defined as construction where:
a
Walls and ceilings exposed to
the outside atmosphere have a
continuous water vapor re-
tarder with a rating of one
perm (6 x 10-11 kg per pa-sec-
m2) or less with openings
gasketed or sealed and
While it is good to make your home
energy efficient, your home needs to
breathe. Fresh air must enter your home.
All fuel-burning appliances need fresh air
for proper combustion and ventilation.
b
c
Weather stripping has been
added on openable windows
and doors and
Exhaust fans, fireplaces, clothes dryers,
and fuel burning appliances draw air from
the house to operate. You must provide
adequate fresh air for these appliances.
Caulking or sealants are
applied to areas such as joints
around window and door
frames, between sole plates and
floors, between wall-ceiling
joints, between wall panels, at
penetrations for plumbing,
electrical, and gas lines, and at
other openings.
If your home meets all of the three
criteria above, you must provide
additional fresh air. See Ventilation
Air From Outdoors, page 5.
If your home does not meet all of
the three criteria above, proceed to
Determining Fresh-Air Flow For
Heater Location, page 4.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR FOR
COMBUSTION AND
VENTILATION
Continued
DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if You Have A Confined or Unconfined Space
Use this work sheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways
or ventilation grills between the rooms.
1. Determine the volume of the space (length x width x height).
Length x Width x Height = ____________________ cu. Ft. (volume of space)
Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. Ft. (volume of space)
if additional ventilation to adjoining room is supplied with grills or openings, add the volume of these
rooms to the total volume of the space.
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
____________________ (volume of space) / 50 cu. Ft. = (maximum Btu/Hr the space can support)
Example: 2560 cu. Ft. (volume of space) / 50 cu. Ft. = 51,200 (maximum Btu/Hr the space can support)
3. Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free heater
Gas water heater*
Gas furnace
Vented gas heater
Gas fireplace logs
________________ Btu/Hr
________________ Btu/Hr
________________ Btu/Hr Example:
________________ Btu/Hr Gas water heater 40,000 Btu/Hr
________________ Btu/Hr
Vent-free heater + 30,000 Btu/Hr
Total = 70,000 Btu/Hr
Other gas appliances* + ________________ Btu/Hr
Total = ________________ Btu/Hr
* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to
the outdoors.
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
______________ Btu/Hr (maximum the space can support)
______________ Btu/Hr (actual amount of Btu/Hr used)
Example: 51,200 Btu/Hr (maximum the space can support)
70,000 Btu/Hr (actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum
Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined
space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From
Inside Building, page 5.
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 5.
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined
space. You will need no additional fresh air ventilation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR FOR
COMBUSTION AND
VENTILATION
Continued
12"
VENTILATION AIR
VENTILATION AIR FROM
INSIDE BUILDING
Ventilation Grills
Into Adjoining Room,
Option 2
Or
Remove
Door into
Adjoining
Room,
Option
3
This fresh air would come from an
adjoining unconfined space. When
ventilating to an adjoining unconfined
space, you must provide two
permanent openings; one within 12"
of the ceiling and one within 12" of
the floor on the wall connecting the
two spaces (See Options 1 and 2,
Figure 2). You can also remove door
into adjoining room (See Option 3,
Figure 2). Follow the National Fuel
Gas Code, NFPA 54/ANSI Z223.1,
Section 5.3, Air for Combustion and
Ventilation for required size of
ventilation grills or ducts.
Ventilation
Grills
Into Adjoining
Room,
Option 1
12”
FIGURE 2 - VENTILATION AIR FROM INSIDE BUILDING
WARNING: Rework work-
sheet, adding the space of the
adjoining unconfined space.
The combined spaces must
have enough fresh air to
supply all appliances in both
spaces.
VENTILATED
ATTIC
OUTLET AIR
OUTLET
AIR
Ventilation Air From Outdoors
TO ATTIC
Provide extra fresh air by using
ventilation grills or ducts. You must
provide two permanent openings: one
within 12" of the ceiling and one
within 12" of the floor. Connect these
items directly to the outdoors or
spaces open to the outdoors. These
spaces include attics and crawl spaces.
Follow the National Fuel Gas Code,
NFPA 54/ANSI Z223.1, Section 5.3,
Air for Combustion and Ventilation
for required size of ventilation grills or
ducts.
TO
CRAWL
SPACE
INLET
AIR
VENTILATED
CRAWL SPACE
INLET AIR
IMPORTANT: Do not provide
openings for inlet or outlet air into
FIGURE 3 - VENTILATION AIR FROM OUTDOORS
attic, if attic has
a
thermostat-
controlled power vent. Heated air
entering the attic will activate the
power vent.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
GAS CONNECTION
IMPORTANT: You must maintain
minimum wall and ceiling clearances
during installation. The minimum
clearances are shown in Figure 4.
Measure from outermost point of stove
top.
Check gas type. Use only the type of
gas indicated on the valve rating
plate. If the type of gas listed on the
plate is not your type of gas
supply,DO NOT INSTALL. Contact
your dealer for proper model.
Always use an external regulator for
all LP heaters to reduce the supply
tank pressure to a maximum of 13"
W.C. This is in addition to the
regulator furnished with the heater.
Minimum Wall and Ceiling
Clearances (See Figure 4)
A. Clearances from outermost
point of stove top to any
combustible side wall should
not be less than 4 inches.
B. Clearances from outermost
point of stove top to any
combustible back wall should
not be less than 4 inches
(Includes Corner Installations).
C. Clearances from the stove top
to the ceiling should not be less
The normal gas connection is 3/8"
NPT made at the right side facing the
log set. If a left side connection is
desired, the connecting pipe may be
routed under the rear of the burner
base to terminate at the right hand
side for connection to the inlet of the
valve.
than 48 inches.
CEILING
FRONT VIEW
48" MINIMUM
4"
4"
MINIMUM
MINIMUM
SIDE
WALL
SIDE
WALL
CLEARANCES TO
COMBUSTIBLES
(Vent-Free Operation Only)
BACK WALL
TOP VIEW
4" MINIMUM
4" MINIMUM
SIDE
WALL
SIDE
WALL
Carefully follow the instructions
below. This stove is a freestanding
unit designed to set directly on the
floor. Do not place stove directly on
carpeting, vinyl tile, or any
combustible material other than
wood. The stove must set on a metal
or wood panel extending the full
width and depth of the appliance.
WALL
CORNER
Maintain adequate clearances for
accessibility for the purpose of
servicing and proper operation.
4" MINIMUM
4"
MINIMUM
WALL
FIGURE 4 - MINIMUM CLEARANCES
TO WALLS AND CEILING
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Continued
STOVE CAVITY ASSEMBLY
1. Lift off corrugated box enclosing
stove body crating.
BOLT
2. Remove all screws fastening the
wood frame enclosure. Spread
wood frame open and lift away
from plastic-bagged stove body.
The bottom pieces of pallet wood
will remain bolted to the stove
body.
BACK STOVE
PANEL
3. Remove plastic bag from stove
body.
4. Remove back panel from stove, if
equipped (See Figure 5). Use an
adjustable wrench or a 10 mm
socket. Remove six (6) bolts and
washers. Keep bolts and washers
to reattach back panel later.
FIGURE 5 - REMOVING BACK PANEL
FRONT OF
STOVE UNIT
5. Remove all contents from inside
stove cavity. Contents include:
TOP OF
STOVE
UNIT
(4) - Legs (includes leg leveler
bolts)
(1) - Bottom door
(3) - Top grates
(1) - Hardware kit bag with
fasteners
REMOVE PALLET
BOLTED TO
STOVE BOTTOM
DROP CLOTH/
BLANKET
6. Carefully lay stove body on back
to attach bottom components to
stove body (See Figure 6). Rest
stove on drop cloth or blanket to
avoid scratching stove edges.
7. Remove remaining pallet wood
attached to bottom of stove body
(See Figure 6). Use an adjustable
wrench to remove bolts.
FIGURE 6 - LAYING DOWN STOVE ON SIDE
CAUTION: Cast Iron is brittle.
Do not over-tighten bolts or
screws during assembly.
DOOR CATCH BOLT
WITH ADJUSTABLE
HEX NUTS HOLE
8. Fasten each leg to stove with four
(4) M8 x 1.25—20 mm bolts. Use
a flat washer and lock washer with
each bolt. Tighten bolts into
threaded holes on stove body (See
Figures 7 and 8). Use an adjustable
wrench or a 12mm socket.
DOOR HINGE STEP
BOLT HOLE
FRONT
LEG
HOLE
LEG
HOLE
BOTTOM OF
STOVE UNIT
LEG
HOLE
LEG
HOLE
FIGURE 7 - LOCATING THREADED HOLES FOR STOVE BOTTOM,LEGS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Attach stove door by inserting
step bolt through door hinge
pivot hole and into threaded hole
in stove body (See Figure 9 and
10 on page 8). Use an adjustable
wrench or a 12mm socket to
fasten step bolt. Tighten step bolt
until snug. Make sure door
moves freely.
11. Check general catch bolt
alignment with door claw. Make
final adjustment and door leveling
after stove is in normal standing
position.
INSTALLATION
Continued
12. Carefully lift stove back up on its
four attached legs.
13. Set top grate into stove top.
14. If available, install gas log heater
inside stove cavity before
installing the back panel (See
Installing Gas Log Heater Into
Stove, page 9).
15. Fasten back panel to stove with
six (6) M6 x 1—20mm bolts and
washers. Make sure product
identification label is located on
the outside in lower left hand
corner.
10. Install door catch bolt (M8 x 1.25
– 55mm with two M8 hex nuts)
into threaded hole on stove body
(See Figure 10, page 8). Use an
adjustable wrench or a 12mm
socket. The catch bolt has two
hex nuts attached to it. The top
nut is a bolt stop and the bottom
nut is for door leveling
adjustment.
STOVE DOOR
STOVE DOOR
BOLT
SHOULDER
WASHERS
BOLTS
BOTTOM OF
STOVE UNIT
THREADED
HOLE
DOOR
HINGE
DOOR
HINGE
FIGURE 8 - ATTACHING STOVE LEGS
NOTE: IF YOUR CASTING HAS A
DROP BOTTOM– DO NOT INSTALL–
DISCARD THE BOTTOM.
STEP
BOLT
STEP
BOLT
BOLT
SHOULDER
STOVE BOTTOM
FIGURE 9 - ATTACHING STOVE DOOR
BOLT STOP
ADJUSTING NUT
DOOR
DOOR CLAW
CATCH BOLT
FIGURE 10 - CATCH BOLT AND DOOR CLAW ORIENTATION
8
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Loosen – Do Not Remove the
two (2) rear side bolts of the
stove, (one (1) on the left rear
side, and one (1) on the right rear
side). Then place a Mounting
Bracket (Mounting Brackets
provided and packaged with Log
Heater Base) between the Bolt
head and the stove body. Ensure
that the other end of the
Mounting Bracket is placed on
the heater base between the Rear
Log Support and the Rear Burner
Holder. Tighten the Bolts (See
Figure 11).
NOTE: Heat Shield is provided with
the Log Heater Base unit.
INSTALLATION
Continued
NOTE: Back Panel is provided with
the Stove unit.
INSTALLING GAS LOG
HEATER (BASE) MODELS
MA C100BATLP OR
FIGURE 12 - BACK PANEL AND
HEAT SHIELD
MA C100BATNAT
TWO (2) TOP BOLTS
HOLD THE HEAT
SHIELD IN PLACE
CAUTION: Do not remove the
metal data plates attached to the
heater base assembly. The data
plates contain important warranty
information.
8. Position logs on base as shown
on page 10, Figure 13.
IMPORTANT: Make sure log
does not cover any burner ports
and does not touch the stove
cavity .
FOUR (4) BOLTS
TOTAL OF (6) SIX
BOLTS
9. Position back panel with label at
lower left corner. Fasten with
bolts at each bottom corner. Do
not tighten completely. Taking
small heat shield provided with
log base position it over back
panel, align two (2) slotted holes
in heat shield with the two (2)
holes in the top of the back panel.
Now fasten the heat shield to the
back of the stove. Start the two
(2) remaining bolts, now tighten
all six (6) bolts. NOTE: Do not
over-tighten bolts. Porcelain on
back panel may crack. (See
Figure 12)
CAUTION: After installation and
periodically thereafter, check to
ensure that no flame comes in
contact with any log. With the
heater set to High, check to see if
flames contact any log. If so,
reposition logs according to the log
installation instructions in this
manual. Flames contacting logs will
create soot.
BACK STOVE PANEL
L
REAR LOG
SUPPORT
1. Remove log and gas log heater from
carton. NOTE: Do not pick up gas log
heater by the burner itself. This could
damage heater. Always handle the gas
log heater by the heater base only.
2. Remove all protective packaging
applied to log and gas log heater for
shipment.
10. Place freestanding stove in de-
sired position in room. Be sure to
maintain clearances to com-
bustibles as outlined on page 6.
3. Check all items for any shipping
damage. If damaged, promptly inform
dealer where you bought heater.
4. If not already removed, remove back
panel from assembled stove body, if
equipped (See Figure 5, page 7). Use
an adjustable wrench or a 10mm
socket. Remove six (6) bolts and
washers. Keep bolts and washers to
reattach back panel later.
5. Facing rear of stove body place gas
log heater base inside stove with
control knob facing inner rear side of
the stove.
6. Slide the Gas Log Heater Base
forward until the front of the base is
against the inner front rear side of the
stove (See Figure 11).
NOTE: After positioning stove in
desired
position, connecting gas
supply and completing all pressure
checks and lighting the heater, make
sure flame is not contacting logs. If
flame is contacting logs, reposition
logs so flame does not contact logs.
MOUNTING BRACKET
SIDE
BOLT
NOTE: Mounting
Brackets must be
placed between the
Rear Log Support
and the Rear Burner
Holder. Brackets
must be tightened
before Back
Panel is replaced.
FIGURE 11 - INSTALLING
LOG HEATER
9
Download from Www.Somanuals.com. All Manuals Search And Download.
“LOG #2 PLACEMENT”
10
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Inside of Firebox you will find three
(3) wires with a switch attached. Dis-
connect the wires from the switch.
Using the remaining mounting bracket
with the switch holder on top, feed
the wires through the wire channel
starting at the end opposite the switch
holder. Continue through the switch
hole in top. Reconnect the three (3)
wires to the switch (make sure the red
wire is connected to the Manual side
of the switch, see page 33). Position
the switch in the switch holder, press
until switch locks into position. (See
Figure 15). Take mounting bracket
and attach to left rear side of stove,
with bolts provided. (See Figure 14)
7. Place freestanding stove in desired
position in room. Be sure to maintain
clearances to combustibles as outlined
on page 6.
MANUAL OFF AUTO
INSTALLATION
INSTALLING GAS LOG
HEATER FIREBOX MODELS
MA CVFB200LP OR
SWITCH
MA CVFB200NAT
RED
WIRE
CAUTION: Do not remove the metal
data plates attached to the heater as-
sembly. The data plates contain impor-
tant warranty information.
SWITCH
HOLDER
MOUNT-
ING
BRACKET
WIRE
CHANNEL
CAUTION: After installation and
periodically thereafter, check to ensure
that no flame comes in contact with any
log. If so, reposition logs according to
the log installation instructions in this
manual. Flames contacting logs will
create soot.
1. Remove logs and heater from carton.
NOTE: Do not pick up gas heater by
the burner itself. This could damage
heater. Always handle the heater by
the firebox only.
8. After positioning stove in desired po-
sition, connect gas supply and com-
plete all pressure checks and light the
heater. (See page 14 Connecting To
Gas Supply)
FIGURE 15 - BRACKET/WIRE
CHANNEL
SWITCH HOLDER (ALSO REFER TO
PAGE 16)
2. Remove all protective packaging ap-
plied to logs and gas log heater for
shipment.
RIGHT
REAR
SIDE
OPTIONAL AIR CHANNEL/
BLOWER ASSEMBLY
SWITCH
LEFT
REAR
SIDE
3. Check all items for any shipping
damage. If damaged, promptly inform
dealer where you bought heater. Place
the logs into the Firebox and follow
the directions on page 10, Figure 13.
4. If not already removed, remove back
panel from assembled stove body
(Stoves sold for the use of a Model
CVF200’s series may not have a back
panel, just the bolts). See back panel
and bolts on page 7, Figure 5. Use a
10mm socket or an adjustable
wrench. Remove six (6) bolts and
washers. Keep bolts and washers to
attach Rear Mounting Brackets.
MOUNTING BRACKETS
BOLTS
BOLTS
5. From rear of stove slide the Firebox
into the Cast Stove until the front of
the Firebox touches the inner front
rear side of the stove. The Firebox
has two Alignment Guides made to
the bottom of the Firebox. These will
ensure a more proper center align-
ment of the Firebox in the Cast Stove.
Then take the mounting bracket with-
out a switch holder and align slots in
bracket with top and bottom holes on
right side of stove. Fasten with bolts
provided. (See Figure 14)
Alignment Guides
FIGURE 14 - BACK OF STOVE WITH FIREBOX INSERT / MOUNT-
ING BRACKETS / SWITCH/ OPTIONAL AIR CHANNEL WITH
BLOWER.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTINUED
9. After lighting the heater check to
ensure that the log placement is cor-
rect, and that no flame is coming in
contact with the logs. If log place-
ment is incorrect reverse steps 5 and
6, and see page 10, Figure 13.
CENTER GRATE
ALIGNMENT STUD
(ALLEN SCREW)
REMOVING CAST STOVE
FRONT PANEL
If at some time you may need to remove
the front panel of your Cast Stove unit
for servicing or replacement follow these
steps.
A. Facing the front of the unit with ac-
cess door in the closed position remove
the two (2) hex screws holding bottom
front of stove in place. Screws are lo-
cated on the bottom front between the
access door and front legs. You may dis-
card the screws . (See Figure 16)
B. Remove the Center Grate located on
the top of the unit.
FRONT PANEL
C. Using an Allen wrench, remove the
Alignment Stud (Allen Screw) from the
top front center of the unit.
NOTE: Be prepared to hold the Front
Panel while removing the Alignment
Stud. The panel may come out by ap-
plying pressure, and may cause damage
to the panel or cause personal injury.
D. Replace front panel and (Allen screw)
Alignment Stud before returning to nor-
mal usage.
DOUBLE DOORS
FRONT PANEL SHIPPING SCREWS
(DISCARD)
FIGURE 16 - FRONT OF CAST STOVE/FRONT PANEL
12
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION OF
OPTIONAL
BLOWER ASSEMBLY
(MODEL MA CVF714)
FOUR (4) HOLES FOR MOUNTING BLOWER ASSEMBLY
FOUR (4) NOTCHES IN
BLOWER ASSEMBLY FOR
MOUNTING
1. Remove Blower Assembly from carton. Re-
move all protective packaging applied to
Blower Assembly for shipment.
2. Check all items for any shipping damage. If
damaged, promptly inform dealer where you
purchased the Blower Assembly.
3. From the rear of the Fire Box, align the four (4)
notches in the Blower Assembly with (4) holes
in the rear of the Fire Box. This will ensure the
centering of the Blower Assembly on the Fire
Box.
4. After determining the area of placement for the
Blower Assembly, attach the Blower Assembly
to the Fire Box using the four (4) #8 x 1/2"
self-piercing mounting screws provided.
come damaged while being installed.
BLOWER ASSEMBLY
(MA CVF714)
FIRE BOX
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dan-
gerous operation.
Verify proper operation after servicing.
If any of the original wire as supplied with the appliance must be replaced, it must be replaced with a wire of at least a 105€
temperature rating.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation must include an equipment
shutoff valve, union, and plugged 1/8"
NPT tap. Locate NPT tap within reach
for test gauge hook up. NPT tap must
be upstream from heater (See Figure
18, BVFB series).
INSTALLATION
Continued
BACK VIEW
BACK STOVE
PANEL
CONNECTING TO GAS
SUPPLY
IMPORTANT: Install equipment
shutoff valve in an accessible location.
The equipment shutoff valve is for
turning on or shutting off the gas to the
appliance.
Apply pipe joint sealant lightly to male
threads. This will prevent excess
sealant from going into pipe. Excess
sealant in pipe could result in clogged
heater valves.
SIDE VIEW
GAS
Installation Items Needed
INLET
CONNEC-
TION
Before installing heater, make sure you
have the items listed below:
FRONT
OF
STOVE
UNIT
ACCESS
•
•
•
•
•
•
•
piping (check local codes)
sealant (resistant to LP gas)
equipment shutoff valve
tests gauge connection
sediment trap
tee joint
pipe wrench
A CSA/AGA design-certified equip-
ment shutoff valve with 1/8" NPT tap is
an acceptable alternative to test gauge
connection. Purchase the optional CSA/
AGA design-certified equipment
shutoff valve from your dealer. See
Accessories, page 23.
FIGURE 17 - GAS REGULATOR LOCATION AND GAS LINE ACCESS INTO
STOVE CABINET
From Gas Meter
(5” W.C.**to 10.5”
W.C. Pressure)
CSA/AGA Design-
Certified Equipment
Shutoff Valve With
1/8” NPT Tap
Approved Flexible Gas
Hose (if allowed by local
codes)
The gas inlet connection for the stove
heater is located on the lower right-
hand side when viewed from the front
of the unit. The gas connection can be
made either through the bottom right
side or through the lower back opening
as illustrated in Figure 17. Make sure
gas log heater is secured to the stove
cavity assembly.
Gas Control
Tee Joint
Pipe Nipple
Cap
3” Minimum
Sediment
Trap
FIGURE 18 - GAS CONNECTION
14
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Check all joints of gas supply
piping system. Apply mixture of
liquid soap and water to gas
joints. Bubbles forming show a
leak.
5. Correct all leaks at once.
6. Reconnect heater and equipment
shutoff valve to gas supply.
Check reconnected fittings for
leaks.
Pressure Testing Heater Gas
Connections
INSTALLATION
Continued
1. Open equipment shutoff valve (See
Figure 19).
2. Open main gas valve located on or
near gas meter.
3. Make sure control knob of heater is in
the OFF position.
4. Check all joints from equipment
shutoff valve to control valve (See
Figure 20). Apply mixture of liquid
soap and water to gas joints. Bubbles
forming show a leak.
5. Correct all leaks at once.
6. Light heater (See Operating Heater,
pages 17 through 19). Check all other
internal joints for leaks.
We recommend that you install a
sediment trap in supply line. Locate
sediment trap where it is within reach
for cleaning. Install in piping system
between fuel supply and heater. Locate
sediment trap where trapped matter is
not likely to freeze. A sediment trap
traps moisture and contaminants. This
keeps them from going into heater
controls. If sediment trap is not
installed or is installed wrong, heater
may not run properly.
Test Pressures Equal To or Less
Than 1/2 psi (3.5 kPa)
1. Close equipment shutoff valve
(See Figure 19).
2. Pressurize supply piping system
by either using compressed air or
opening main gas valve located
on or near gas meter.
3. Check all joints from gas meter
to equipment shutoff valve (See
Figure 20). Apply mixture of
liquid soap and water to gas
joints. Bubbles forming show a
leak.
CAUTION: Avoid damage to
regulator. Hold gas regulator
with wrench when connecting it
to gas piping and/or fittings.
7. Turn off heater (See To Turn Off Gas
to Appliance on pages 17 through
19).
Input
Rating
Minimum
22,400
Maximum
32,000
CHECKING GAS
CONNECTIONS
Type of Gas
Manifold
LP/Propane
Natural
4. Correct all leaks at once.
Pressure
*Min. Inlet
Max. Inlet
10.0"wc
10.5"wc
13.0"wc
3.5"wc
4.5"wc
10.5"wc
EQUIPMENT
SHUTOFF
VALVE
*For purpose of input adjustment.
OPEN
CLOSED
The appliance must be isolated from the gas
supply piping system by closing its equipment
shutoff valve during any pressure testing of the
gas supply piping system at test pressures equal
to or less than ½ psi (3.5 kPa).
FIGURE 19 - EQUIPMENT SHUTOFF
VALVE
Pressure Testing Gas Supply
Piping System
Test Pressures In Excess of 1/2 psi
(3.5 kPa)
EQUIPMENT
SHUTOFF
VALVE
1. Disconnect appliance with its
appliance main gas valve (control
valve) and equipment shutoff valve
from gas supply piping system.
Pressures in excess of 1/2 psi will
damage heater regulator.
GAS METER
2. Cap off open end of gas pipe
where equipment shutoff valve
was connected.
3. Pressurize supply piping system by
either using compressed air or
opening main gas valve located on
or near gas meter.
CONTROL VALVE LOCATION
FIGURE 20 - CHECKING GAS JOINTS
15
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING HEATER
*Please refer to page 25 for location
and picture of pilot.
FLAME ADJUSTMENT KNOB
THERMOCOUPLE
PILOT BURNER
IGNITOR ELECTRODE
SELECTOR
SWITCH
CONTROL KNOB
FIGURE 22 - O.D.S PILOT
ASSEMBLY SHOWN AS L.P.
GAS.
IGNITOR BUTTON
FIGURE 21 - CONTROL KNOB AND IGNITOR BUTTON
LOCATION
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING HEATER
Continued
OPERATING HEATER
Continued
PILOT FLAME PATTERN
(MILLIVOLT)
Figure 23 shows a correct pilot flame
pattern. Figure 24 shows an incorrect
pilot flame pattern. The incorrect pilot
flame is not heating the thermo-
couple. This will cause the thermo-
couple to cool. When the thermo-
couple cools, the heater will shut
down.
If pilot flame pattern is incorrect, as
shown in Figure 24:
•
Turn heater off (see To turn Off
Gas to Appliance, page 17)
See Troubleshooting, pages 20
through 22.
•
THERMOPILE/
FIGURE 23 - CORRECT FLAME PATTERN L.P. OR NAT. GAS
OPTIONAL REMOTE
CONTROL
NOTE: All remote control accessories
must be purchased separately (see
Accessories). Follow instructions
included with the remote control.
THERMOPILE/
NOTICE: You must light the pilot
before using the remote control unit.
See Lighting Instructions on page 17.
FIGURE 24 - INCORRECT PILOT FLAME PATTERN L.P. OR NAT. GAS
18
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTING
AND CLEANING
MAINTENANCE
move it back to the correct position
after cleaning.
LOGS
•
If you remove logs for cleaning,
4. Opening the shutter as in step 3,
allows you to inspect the orifice.
After cleaning the area adjust air
shutter to the original position.
5. Blow air through the slots and
holes in the burner.
6. Blow air into the primary air holes
on the injector holder.
7. In case any large clumps of dust
have now been pushed into the burner
repeat steps 3 and 4.
refer to Installing Gas Log Heater
into Stove, page 9, to properly
replace logs.
CAUTION: You must keep
control areas, burner, and
circulating air passageways of
heater clean. Inspect these areas
of heater before each use. Have
heater inspected yearly by a
qualified service person. Heater
may need more frequent cleaning
due to excessive lint from
carpeting, pet hair, bedding
material, etc.
MAIN BURNER
Periodically inspect all burner flame
holes with the heater running. All
slotted burner flame holes should be
open with flame present. Some burner
flame holes may become blocked by
debris or rust, with no flame present. If
so, turn off heater and let cool. Either
remove blockage or replace burner.
Blocked burner flame holes will create
soot.
Clean the pilot assembly also. A yel-
low tip on the pilot flame indicates
dust and dirt in the pilot assembly.
There is a small pilot air inlet hole
about two inches from where the pilot
flame comes out of the pilot assembly
(See Figure 26). With the unit off,
lightly blow air through the air inlet
hole. You may blow through a drink-
ing straw if compressed air is not
available.
CLEANING BURNER
INJECTOR HOLDER AND
PILOT AIR INLET HOLE
The primary air inlet holes allow the
proper amount of air to mix with the
gas. This provides a clean burning
flame. Keep these holes clear of dust,
dirt, lint, and pet hair. Clean these air
inlet holes prior to each heating season.
Blocked air holes will create soot. We
recommend that you clean the unit
every three months during operation
and have heater inspected yearly by a
qualified service person.
TRANSPORTING STOVE
Porcelain enamel coatings contain
glass and are brittle. To prevent
cracking of the porcelain finish, do not
transport stove with top grates in place.
BURNER SLOTS
BURNER TUBE
We also recommend that you keep the
burner tube and pilot assembly clean
and free of dust and dirt. To clean these
parts we recommend using compressed
air no greater than 30 PSI. Your local
computer store, hardware store, or
home center may carry compressed air
in a can. You can use a vacuum cleaner
in the blow position. If using
compressed air in a can, please follow
the directions on the can. If you don’t
follow directions on the can, you could
damage the pilot assembly. NOTE:
Removing the rear panel (Figure 5,
page 7) and top grates of your stove
will make cleaning easier.
PHILLIPS SCREW
AIR SHUTTER
AIR SHUTTER SLOTS
FIGURE 25 - BURNER/ AIR SHUTTER
O.D.S PILOT BURNER
1. Shut off the unit, including the
pilot. Allow the unit to cool for at
least thirty minutes.
2. Inspect burner, pilot, and slots in
air shutter for dust and dirt.
PILOT AIR HOLE
3. Using Phillips head driver loosen
set screw on air shutter and rotate
shutter toward rear of unit.
NOTE:Before rotating shutter
mark the position of shutter so
you can
FIGURE 26 - PILOT ASSEMBLY
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
NOTE: All troubleshooting items are
listed in order of operation.
POSSIBLE CAUSE
OBSERVED PROBLEM
REMEDY
1. Ignitor electrode not connected to
ignitor cable
2. Ignitor cable pinched or wet
When ignitor button is pressed, there is
no spark at ODS/pilot
1. Reconnect ignitor cable
2. Free ignitor cable if pinched by
any metal or tubing. Keep ignitor
cable dry
3. Replace ignitor cable
4. Replace piezo ignitor
5. Replace piezo ignitor
6. Replace piezo ignitor
3. Broken ignitor cable
4. Bad piezo ignitor
5. Ignitor electrode broken
6. Ignitor electrode positioned
wrong
1. Gas supply turned off or
equipment shutoff valve closed
2. Control knob not in PILOT
position
3. Control knob not pressed in while
in PILOT position
When ignitor button is pressed, there is
spark at ODS/pilot but no ignition
1. Turn on gas supply or open
equipment shutoff valve
2. Turn control knob to PILOT
position
3. Press in control knob while in
PILOT position
4. Continue holding down control
knob. Repeat igniting operation
until air is removed
5. Clean ODS/pilot (see Cleaning
and Maintenance, page 19) or
replace ODS/pilot assembly
6. Replace gas control
4. Air in gas lines when installed
5. ODS/pilot is clogged
6. Gas regulator setting is not
correct
1. Control knob not fully pressed in
2. Control knob not pressed in long
enough
3. Equipment shutoff valve not fully
open
ODS/pilot lights but flame goes out
when control knob is released
1. Press in control knob fully
2. After ODS/pilot lights, keep con-
trol knob pressed in 30 seconds
3. Fully open equipment shutoff
valve
4. Pilot flame not touching
thermocouple, which allows
thermocouple to cool, causing
pilot flame to go out. This
problem could be caused by one
or both of the following:
4. Contact local natural gas company
•
Clean ODS/pilot (see
Cleaning and Maintenance,
page 19) or replace ODS/
pilot assembly
A. Low gas pressure
B. Dirty or partially clogged
ODS/pilot
5. Thermocouple connection loose
at control valve
6. Thermocouple damaged
7. Control valve damaged
5. Hand tighten until snug, then
tighten 1/4 turn more
6. Replace thermocouple
7. Replace control valve
1. Clean burner (see Cleaning and
Maintenance, page 19) or replace
burner orifice
2. Contact local gas company
3. Replace burner orifice
4. Reconnect leads
1. Burner orifice clogged
2. Inlet gas pressure is too low
3. Burner orifice diameter is too
small
4. Thermopile/Generator leads
disconnected or improperly
connected
Burner does not light after ODS/pilot is
lit
5. Replace battery in transmitter and
receiver
5. Burners will not come on in
remote position
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Delayed ignition burner
1. Manifold pressure is too low
2. Burner orifice clogged
1. Contact local gas company
2. Clean burner (see Cleaning and
Maintenance, page 19) or replace
burner orifice
Burner backfiring during combustion
1. Burner orifice is clogged or
damaged
1. Clean burner (see Cleaning and
Maintenance, page 19) or replace
burner orifices
2. Replace damaged burner
3. Replace gas control
2. Damaged burner
3. Gas regulator defective
Slight smoke or odor during initial operation
1. Not enough air
1. Check burner for dirt and debris.
If found, clean burner (see
Cleaning and Maintenance, page
19)
2. Replace gas control
3. Problem will stop after a few
hours of operation
2. Gas regulator defective
3. Residues from manufacturing
processes and logs curing
Moisture/condensation noticed on windows
1. Not enough combustion/ventila–
tion air
1. Refer to Air for Combustion and
Ventilation requirements (page 3)
Heater produces a whistling noise when
burner is lit
1. Turning control knob to HI
position when burner is cold
2. Air in gas line
1. Turn control knob to LO position
and let warm up for a minute.
2. Operate burner until air is
removed from line. Have gas line
checked by local gas company
3. Observe minimum installation
clearances (see page 6)
4. Clean burner (see Cleaning and
Maintenance, page 19) or replace
burner orifice
3. Air passageways on heater
blocked
4. Dirty or partially clogged burner
orifice
Dark residue on logs or inside of fireplace
1. Improper log placement
1. Properly locate logs (see Installing
Gas Log Heater, page 9)
2. Eliminate source of drafts around
heater
3. Clean out air holes at burner inlet.
Periodically repeat as needed
4. Remove blockage or replace
burner
2. Drafts or other air currents
affecting flame pattern
3. Air holes at burner inlet blocked
4. Burner flame holes blocked
1. When heated, vapors from furn-
iture polish, wax, carpet cleaners,
etc. turn into white powder
residue
White powder residue forming within burner
box or on adjacent walls or furniture
1. Turn heater off when using
furniture polish, wax, carpet
cleaners, or similar products
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Continued
WARNING: If you smell gas
Shut off gas supply.
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in
your building.
Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
IMPORTANT: Operating heater where impurities in air exist may create
odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements
and glues, new carpet or textiles, etc., create fumes. These fumes may mix
with combustion air and create odors. These odors will disappear over time.
REMEDY
POSSIBLE CAUSE
OBSERVED PROBLEM
1. This is common with most heaters.
If noise is excessive, contact qual-
ified service person
1. Metal expanding while heating or
contracting while cooling
Heater produces a clicking/ticking noise
just after burner is lit or shut off
1. Open window and ventilate room.
Stop using odor causing products
while heater is running
2. Locate and correct all leaks (see
Checking Gas Connections, page
15)
1. Heater burning vapors from paint,
hair spray, glues, cleaners chemicals,
new carpet, etc. (see IMPORTANT
statement above)
2. Gas leak. See WARNING
statement at top of page
Heater produces unwanted odors
1. Open window and/or door for
ventilation
1. Not enough fresh air is available
Heater shuts off in use (ODS operates)
2. Contact local gas company
3. Clean ODS/pilot (see Cleaning
and Maintenance, page 19)
2. Low line pressure
3. ODS/pilot is partially clogged
1. Locate and correct all leaks (see
Checking Gas Connections, page
15)
1. Gas leak. See WARNING
Gas odor even when control knob is in
OFF position
statement at top of page
2. Replace control valve
2. Control valve defective
1. Take apart gas tubing and remove
foreign matter
1. Foreign matter between control
valve and burner
Gas odor during combustion
2. Locate and correct all leaks (see
Checking Gas Connections, page
15)
2. Gas leak. See WARNING
statement at top of page
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE HINTS
REPLACEMENT
PARTS
ACCESSORIES
Purchase these heater accessories from
your local dealer. If they can not sup-
ply these accessories, call our Parts
Department at 1-828-765-6144 for re-
ferral information. You can also write
to the address listed on the back page
of this manual.
When Gas Pressure Is Too Low
NOTE: Use only original replacement
parts. This will protect your warranty
coverage for parts replaced under
warranty.
•
•
Pilot will not stay lit
Burners will have delayed
ignition
•
Heater will not produce specified
heat
RECEIVER AND HAND-HELD
REMOTE CONTROL KIT
PART# PO FDC-504
When Gas Quality Is Bad
•
•
Pilot will not stay lit
Burners will produce flames and
soot
For remote-ready models. Allows the
gas log heater to be turned on and off
by using a hand-held remote control.
•
Heater will backfire when lit
You may feel your gas pressure is too
low or gas quality is bad. If so,
contact your local gas supplier.
WALL THERMOSTAT
PART# PE 400142
The desired comfort setting can be se-
lected on the wall thermostat and the
log heater will automatically cycle
from pilot to the heat setting selected.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
FOR MODELS MA C100BALTLP, MA C100BATNAT, AND
MA CVFB200LP, MA CVFB200NAT
MILLIVOLT (SIT)
KEY #
1
PART #
DESCRIPTION #
PE 8204C
PE 8404C
PILOT ASSEMBLY NATURAL GAS
PILOT ASSEMBLY L.P.
2
3
PO 10-2121-12
FLEXIBLE SUPPLY LINE
PE 820637
PE 820636
(SIT) MILLIVOLT VALVE NATURAL GAS
(SIT) MILLIVOLT VALVE L.P.
4
5
6
7
PE 916188
PE 916189
PE RC211RB
PE 124461
ON/OFF KNOB EXTENSION
HI/LO KNOB EXTENSION
AUTO/OFF/MANUAL
PIEZO STRIKER
8
8A
POT6-06
POT6-12
6" MANIFOLD SUPPLY LINE
12" MANIFOLD SUPPLY LINE
9
PO H- BURN001
18" H-BURNER
10
PO 60MVORF
PO 62MVORF
PO 54MVORF
PO 53MVORF
PO 44MVORF
L.P. FRONT ORIFICE MA C100BALTLP (ONLY)
LP. FRONT ORFICE MA CVFB200LP (ONLY)
L.P. REAR ORIFICE
NAT. FRONT ORIFICE
NAT. REAR ORIFICE
NOTE: REFER TO PAGES 25 AND 26.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
BREAKDOWN FOR
CAST STOVE SERIES
TOWNSEND II
(Discarded During
Assembly)
SEE PAGE 28 FOR PARTS DESCRIPTION AND PART NUMBERS.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
TOWNSEND II
(* INDICATES COLOR SUFFIX DESIGNATION)
28
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AVAILABLE-NOT SHOW
TOWNSEND II
REPLACEMENT PARTS
OPTIONAL BLOWER ASSEMBLY
(MA CVF714)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS BREAKDOWN FOR
CAST STOVE SERIES
HEPPLEWHITE
30
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
HEPPLEWHITE
31
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
HEPPLEWHITE
PARTS AVAILABLE-NOT SHOWN
HEPPLEWHITE
32
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAM
33
Download from Www.Somanuals.com. All Manuals Search And Download.
|
