Network Technologies Carrying Case RACKMUX Series User Manual

1275 Danner Dr Tel:330-562-7070

_RNETWORK

Fax:330-562-1999

TECHNOLOGIES Aurora, OH 44202

www.networktechinc.com

INCORPORATED

NTI

RACKMUX^®Series

RACKMUX-T15

Rack Mount ANSI Terminal Drawer

Installation and Operation Manual

MAN029 Rev Date 10/18/2007

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

Introduction......................................................................................................................................................................1

Materials..........................................................................................................................................................................2

Features and Functions...................................................................................................................................................3

1. Installation ...................................................................................................................................................................4

1.1 Rack Mounting Instructions ...................................................................................................................................4

1.1.1 Standard Rack.................................................................................................................................................4

1.1.2 Optional Telco 2-Post Mounting ......................................................................................................................5

1.2 Connect The Cables..............................................................................................................................................6

1.3 Power Up The Terminal.........................................................................................................................................7

2. Using The RACKMUX.................................................................................................................................................7

2.1 How To Setup The Terminal..................................................................................................................................7

2.1.1 Entering Setup.................................................................................................................................................7

2.1.2 Saving and Exiting Setup.................................................................................................................................7

2.1.3 Setup Directory................................................................................................................................................7

2.1.4 Default Configuration.......................................................................................................................................8

2.2 Changing The Operating Parameters....................................................................................................................9

3. Local Keyboard Commands......................................................................................................................................16

4. Connector Pin Assignment........................................................................................................................................17

5. Command Guide .......................................................................................................................................................18

5.1 Commands Supported in ASCII Personalities.....................................................................................................18

5.2 Variable Values for Table 10 Commands............................................................................................................25

6. ANSI Command Guide.............................................................................................................................................29

6.1 VT100, VT220 and Console ANSI Command Guide ..........................................................................................29

6.2 VT52 Command Guide........................................................................................................................................36

7. Using Printer Server in Ethernet Terminal ................................................................................................................37

Introduction................................................................................................................................................................37

7.1 Basic Setup.......................................................................................................................................................37

7.2 Setup for LPD ...................................................................................................................................................37

7.3 LPD printing ......................................................................................................................................................38

7.4 Setup for TFTP .................................................................................................................................................39

7.5 TFTP Printing....................................................................................................................................................39

8. On-Screen Display (OSD).........................................................................................................................................40

8.1 Standard Controls................................................................................................................................................40

8.2 OSD Control Menu ..............................................................................................................................................40

8.2.1 OSD Main Menu ............................................................................................................................................40

8.2.2 Brightness/Contrast Menu .............................................................................................................................41

8.2.3 Color Menu ....................................................................................................................................................41

8.2.4 Position Menu................................................................................................................................................41

8.2.5 Setup Menu....................................................................................................................................................42

9. Keyboard Functions ..................................................................................................................................................43

9.1 Function Key Operation.......................................................................................................................................43

9.2 Number Pad.........................................................................................................................................................44

9.3 Other Uses of the Function Key ..........................................................................................................................45

9.4 Numeric Keypad Option ......................................................................................................................................45

10. CPU-to-RACKMUX Ethernet Crossover Cable.......................................................................................................46

11. DC Power Option ....................................................................................................................................................47

Dimensional Drawings...................................................................................................................................................48

Frequently Asked Questions .........................................................................................................................................49

Technical Specifications................................................................................................................................................50

Troubleshooting.............................................................................................................................................................51

Index..............................................................................................................................................................................51

Warranty Information.....................................................................................................................................................51

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF FIGURES

Figure 1- Mount RACKMUX to rack...................................................................................................................................................4

Figure 2- Position RACKMUX with clearance to open .......................................................................................................................4

Figure 3- Mount to Telco post with optional mounting brackets.........................................................................................................5

Figure 4 -Connect a CPU to the RACKMUX......................................................................................................................................6

Figure 5- Connect to CPU using Ethernet cable................................................................................................................................6

Figure 6- Function keys to press for submenus.................................................................................................................................7

Figure 7- OSD Controls ...................................................................................................................................................................40

Figure 8- US (English) Keyboard Layout .........................................................................................................................................43

Figure 9- Keyboard LED Indications................................................................................................................................................43

Figure 10- Keys of the Number Pad ................................................................................................................................................44

Figure 11- Additional multi-function keys .........................................................................................................................................45

Figure 12- U.S. (English) keyboard with numeric keypad ................................................................................................................45

Figure 13- U.K. (English) keyboard with numeric keypad ................................................................................................................46

Figure 14- German keyboard with numeric keypad .........................................................................................................................46

Figure 15- RACKMUX with DC Power option ..................................................................................................................................47

Figure 16- Apply wires to terminal block ..........................................................................................................................................47

LIST OF TABLES

Table 1- Main Setup Menu Exit Functions .........................................................................................................................................7

Table 2- Programmable Keys ..........................................................................................................................................................12

Table 3- Color Setup Menu..............................................................................................................................................................13

Table 4- Color Palettes ....................................................................................................................................................................14

Table 5- Local Keyboard Commands in Native Mode......................................................................................................................16

Table 6- Serial Port (Serial 1) Connector Pin Assignments .............................................................................................................17

Table 7- Serial Port (Serial 2) Connector Pin Assignments .............................................................................................................17

Table 8- Printer Port Connector Pin Assignments ...........................................................................................................................17

Table 9- 10Base T Connector Pin Assignments ..............................................................................................................................17

Table 10- Commands Supported in ASCII Personalities .................................................................................................................18

Table 11- VT52 Mode Escape Sequences ......................................................................................................................................36

Table 12- Number Pad Keys............................................................................................................................................................44

_{Download from Www.Som}i_ai_ni_{uals.com. All Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

INTRODUCTION

The RACKMUX-T15 (formerly referred to as RACKMUX-TERMINAL) Rack Mount ANSI Terminal Drawer (RACKMUX) places a

VTxx/ANSI Terminal right in the rack for space-saving, convenient control of SUN or PC-based headless servers. This LCD

monitor terminal drawer eliminates the need for an external laptop or table-top dumb terminal. This flexible terminal is easy to

install and configure for either of the following communication modes:

RS232 Terminal (using a RS-232 port for serial console connection). Use this configuration of the RACKMUX with the NTI

SERIMUX™ Console Serial Port Switch to control multiple servers.

Telnet Terminal (using an RJ45 10Base-T network port for Ethernet telnet console connection). The Ethernet connection can be

used with any 10Mb-compatible Ethernet host adapter, but is most suited for use with RSC (Remote System Control) Ethernet

ports, since these provide the same functionality as serial (ttya) console ports. This connection supports up to 12 telnet sessions

to different servers. The state of each server session is preserved by the terminal. Terminal sessions can be switched via hot-

keys. When using the Ethernet telnet connection, the Terminal Drawer can be connected to multiple servers via an Ethernet

switch. However, it is advisable that the network used to connect the server consoles remains private for security reasons.

Note: Both RS232 serial and Ethernet telnet connections cannot be active at the same time.

This general purpose character terminal drawer offers full transaction capabilities and is largely pre-configured for most

applications. It was designed in conjunction with SUN Microsystems to ensure flawless compatibility with all SUN servers. It is also

compatible with most racks, including the Sun StorEdge 72", Sun Fire rack, and most EIA 19" racks. This console drawer is the

ideal solution for controlling web servers, DNS servers, mail servers and other equipment that lack video card capability, such as

the SUN Netra systems and HP servers.

The RACKMUX Terminal drawer is also available with an integrated console switch (RACKMUX-T15-RS16 or RACKMUX-T15-

SS8). See our website for details.

Features

•

Entire unit is only 1U (1.75") high

High-quality metal construction (ideal for most industrial and commercial settings)

15" TFT Rack Mount flip-up LCD Monitor features a wide viewing angle

Screen size: 80x24 characters plus status line

Keyboard lock prevents unauthorized use

Auto shut-off switch: turns OFF power to the monitor when the LCD is folded closed

Display format of 800x600

LCD Display controls (using on-screen menu)

83-key (US) or 84-key (UK, German, French, Italian, Spanish) keyboard with wrist pad

Supports RSC capabilities

Serial and parallel slave-printer ports

Includes rack mount kit suitable for SUN and most EIA 19" racks (fits 22" to 39" rack depths via adjustable mounting

brackets)

•

Optional support for mounting in a two-post Telco rack

Optional protective anti-glare, tempered glass shield

Internally mounted AC power supply or optional 48VDC power input

Locking rails to prevent movement of the drawer when fully extended

Multiple RS-232 Emulations:

•

ADDS A2

PC TERM

PCG Alpha

Console ANSI

TVI910+

•

VT100

VT220

WY-50+

WY-60

WY-100

WY-120

WY-325

TV1925

VT52

Compatibility

•

Compatible with any SUN or PC-based headless server.

Communicates with routers, bridges, firewalls, and hubs

Download from Www.Somanuals.com. All Manuals Search And Download.

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Options

•

LCD anti-glare protective glass shield - add a "G" to the model when ordering (i.e. RACKMUX-T15G)

Telco 2-post style mounting kit- order RL-T15-TEL

DC Power option- for use with 36-72VDC input- add “48V” to the part number (i.e. RACKMUX-T1548V)

Numeric keypad option- for a separate 17-key numeric keypad, add “-N” to the part number (i.e. RACKMUX-T15-N)

See our catalog, visit our website at http://www.networktechinc.com, or contact an NTI sales representative at 800-742-8324 (800-

RGB-TECH) or 330-562-7070 for more details.

MATERIALS

Materials Supplied with this kit:

•

NTI RACKMUX-T15 Rack Mount ANSI Terminal Drawer

VEXT-1,5-MM 1-1/2 foot 15HD VGA male-male cable

9DF25DM-NUL-6 6 foot DB9 female to DB25 male null modem cable

IEC Power Cord, country specific

2 Keys for Lock

2 Rear Mounting Brackets w/nuts

8 #10-32x3/4” screws and cage nuts for mounting to a rack

Download from Www.Somanuals.com. All Manuals Search And Download.

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Front View

RACKMUX-T15

Rear View

RACKMUX-T15

16 17

20 21

FEATURES AND FUNCTIONS

1. Power Button- press to turn the LCD monitor ON and OFF

2. Power LED- indicates operation status

Green=Power-On, Video Input Signal OK

Red = Suspend / Stand-by, or no Video Input Signal

3. Menu Button- press to turn ON the OSD menu

4. Up Arrow Button- press to move the cursor in the OSD menu up

5. Down Arrow Button- press to move the cursor in the OSD menu down

6. Select Button- press to select a menu item (when OSD menu is ON) or press to auto adjust the video quality (when OSD

menu is OFF)

7. NumLock LED- illuminates when the number lock is ON

8. CapsLock LED- illuminates when CapLock is ON

9. Scroll Lock LED- illuminates when ScrollLock is ON

10. Fn LED- illuminates when Function Features (page 43) are enabled.

11. Keyboard- for manual data entry and computer control

12. LCD Display- for viewing the video signal from the connected CPU

13. Key Lock- to secure the keyboard in a closed position preventing unauthorized use

14. Auto Shut OFF Switch- automatically shuts OFF the LCD display when the monitor is folded down

15. IEC Connector- for attachment of the IEC power cord to power the keyboard and mouse

16. VGA- for connection of the VGA cable from the MONITOR port for the LCD display

17. Monitor- for connection of the VGA cable to support the LCD display

18. Serial #2-male SUB D 9 connector- for attaching a local printer serially

19. Parallel- female SUB D 25 connector- for attaching local printer with parallel printer cable

20. Serial #1- male SUB D 9 connector- for attaching the serial interface cable from CPU

21. 10 Base T- female RJ45 connector- for connecting 10 Base-T Cat 5 Ethernet cable

22. VEXT-1,5-MM- 1-1/2 foot 15HD male-male VGA cable- to connect the VGA port to the Monitor port

Download from Www.Somanuals.com. All Manuals Search And Download.

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

1. INSTALLATION

1.1 Rack Mounting Instructions

1.1.1 Standard Rack

The RACKMUX was designed to be mounted to a rack and includes mounting flanges to make attachment easy.

1. Determine the mounting height in the rack for the drawer. It should be a height comfortable to use the keyboard and see the

LCD display. Mark holes in each of the 4 corner cabinet rails at points all level with each other.

2. Secure the rear brackets to the rear rack cabinet rails at the holes marked in step 1 using #10-32x3/4” screws and cage nuts

(supplied). Be sure to tighten the screws securely.

3. Lift the keyboard into position and line the studs on the left and right sides up with the slotted openings in the rear bracket.

Apply the nuts (supplied) to the studs but do not tighten the nuts yet.

FYI: There are 5 mounting studs provided on each side of the RACKMUX. Depending on the depth of the rack and

distance apart of the cabinet rails, the position of the rear bracket may make all 5 studs available for use. In this case,

apply the 2 nuts to the studs furthest apart from each other on each side.

4. Slide the drawer in until the top holes in the front bracket flanges line up with the holes marked in step 1. Secure the front

brackets on the drawer to the front cabinet rails using #10-32x3/4” screws and cage nuts (supplied). Be sure to tighten the

screws securely. Then tighten the nuts applied in step 3.

Front Cabinet

Rear Cabinet

Rail

Stud on drawer

Rear bracket overlapping

Front bracket

flange on drawer

Drawer

drawer

(Rear edge

of drawer)

Rear bracket

flange

Apply nuts (supplied) to studs and

secure rear brackets to drawer.

Figure 1- Mount RACKMUX to rack

Note: To provide sufficient room for the LCD monitor to be opened to a proper viewing angle (a minimum 90 degree

position from the keyboard), ensure that all devices mounted above the RACKMUX extend no more than 1.75” from the

rack frame. (See Fig. 2)

"X" must be

less than 1.75"

for LCD to open

to full 90

Server mounted

above RACKMUX

in the same rack

Side View of RACKMUX-T15

Figure 2- Position RACKMUX with clearance to open

Download from Www.Somanuals.com. All Manuals Search And Download.

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

1.1.2 Optional Telco 2-Post Mounting

If the Telco 2-post mounting bracket kit (RL-T15-TEL) is to be used, secure the short and long brackets to each side of the drawer

as shown in Fig. 3. Apply 2 nuts (supplied) per bracket to secure the brackets to the drawer. Apply two #10-32x3/4” screws

(supplied) per bracket to the post at the desired height. Slots are provided in the brackets to make minor depth adjustments

easy. Be sure to properly tighten all nuts and screws before using the drawer.

Figure 3- Mount to Telco post with optional mounting brackets

Download from Www.Somanuals.com. All Manuals Search And Download.

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

1.2 Connect The Cables

1. Connect a female SUB D 9 end of the null modem cable (supplied) to the "SERIAL 1" male SUB D 9 serial interface

connector on the RACKMUX (see Fig. 4).

2. Connect the other end of the null modem cable to a CPU.

Alternatively, use an Ethernet cable to connect to a CPU (see Fig. 5). For direct connection, use a crossover cable (see

pinout on page 46). For connection through a Local Area Network (LAN), use a patch cable wired straight through (pin

1 to pin 1, pin 2 to pin 2, etc.).

Note: A serial cable (Figure 4) and Ethernet cable cannot both be connected at the same time.

3. Connect the VEXT-1.5-MM cable between the

Attach local printer

ports labeled "MONITOR" and "VGA".

either by parallel cable to Parallel

or by serial cable to Serial 2

4. If connecting a printer, connect

either a serial printer cable to

the remaining male SUB D 9

connector or a parallel printer

cable to the female SUB D 25

connector (see page 3, items

19 & 20).

Rear View

RACKMUX-T15

IEC Powercord

(supplied)

5. Connect the IEC power cord to

the IEC connector.

15HD male

Video Connector

Rear View of CPU

VEXT-1,5-MM (supplied)

9DF25DM-NUL-6

(supplied)

SUB D 9 female

connector

SUB D 25 male

connector

Figure 4 -Connect a CPU to the RACKMUX

Rear View

RACKMUX-T15

male RJ45

connector

Server

Rear View of CPU

10Base T Ethernet Cable

(crossover cable)

male RJ45

connector

Server

LAN

10Base T

Ethernet

Cable

(patch cable)

Figure 5- Connect to CPU using Ethernet cable

Download from Www.Somanuals.com. All Manuals Search And Download.

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

1.3 Power Up The Terminal

1. Plug in to power ON the RACKMUX.

2. Using the key, unlock the drawer and slide the keyboard and LCD Display out far enough to raise the display to a comfortable

viewing angle.

3. Adjust the screen's brightness and contrast with the controls located on the monitor– as needed (see page 40).

2. USING THE RACKMUX

2.1 How To Setup The Terminal

The RACKMUX is compatible with most CPUs and application packages. A menu driven setup system is provided

to select and save the settings required by the CPU and application. A user must be familiar with the requirements of

the CPU in order to setup the RACKMUX.

2.1.1 Entering Setup

Hold down the <ALT> key and then depress the <Esc> key to enter Setup mode. When entering Setup, any text on the screen

temporarily disappears, and the main SETUP directory appears (See Figure 6). When leaving the Setup mode, the main SETUP

directory disappears, and any text that was on the screen will reappear.

2.1.2 Saving and Exiting Setup

The first menu seen when entering Setup serves as a directory to the other Setup menus. To exit Setup or any submenu, press

<F12>. Pressing <F12> will return the display to the main Setup directory and with another press of <F12> the user will be given

the option of saving the selections made.

The highlighted field at the right of the screen gives the user the choice of saving or not saving parameter changes in the

memory before returning the terminal to the normal operating mode.

NOTE: If settings are not saved before leaving the Setup mode, any new selections will be lost when the RACKMUX is

powered-down.

To save Setup selections, depress the Spacebar to change the save field at the right side of the screen from NO to YES before

exiting Setup. (Table 1 describes your options on exiting Setup.)

Depress <F12> to leave Setup and return to the normal display mode.

Table 1- Main Setup Menu Exit Functions

Option

Function

Returns terminal to normal operating mode without saving parameter changes for power up

Yes

Saves all changes (operating parameter, tabs, key definition, and answerback message); returns terminal

to its normal operating mode.

Shift + Esc

Restores all setting (operating parameters, tabs, key definitions, and answerback message) to default values.

2.1.3 Setup Directory

The fields at the bottom of the screen (Figure 6) show the various setup menus where the terminal's operating parameters can be

changed and the function key to press to immediately display any menu.

Figure 6- Function keys to press for submenus

Download from Www.Somanuals.com. All Manuals Search And Download.

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

2.1.4 Default Configuration

The terminal is delivered pre-configured with the following settings suitable for most RS232 serial console connections at 9600

baud using VT-100 emulation.

Disp SETUP Menu

F2 General SETUP Menu

F3 Keybd SETUP Menu

Columns = Econ-80

Cursor = Blink Block

Screen Saver = Off

Lines = 24

Background = Dark

Page Length = 1 x Lines

Auto Page = Off

Personality = VT 100

Enhance = On

Keyclick = Off

Key Repeat = 5

Xmt Limit = None

Margin Bell = Off

Language = US

Keycode = ASCII

NRC = Off

Status Line = Standard

Scroll Speed = Jump

Auto Scroll = On

End of Line Wrap = On

Rcvd CR = CR

Width change clear = Off

ANSI Reverse = Off

Display= LCD

Monitor = Off

Attribute = Char

Bell Volume = 2

NUM Start = Off

DEL Keypad = Dot/Del

F4 Comm SETUP Menu

F5 Misc SETUP Menu

F9 Lan Setup Menu

Baud rate = 9600

Data / Stop Bits = 8/1

Parity = None

Wprt Intensity = Dim

Wprt Reverse = Off

Local IP Address = {blank}

Netmask = {blank}

Gateway = {blank}

Remote IP 0..B Address ={blank}

Port 0...B = 23

Term Type = vt100

Wprt Underline = Off

Block End = US/CR

Ptr Baud rate = 38400

Ptr Data/Stop Bits = 8/1

Ptr Parity = None

Ptr Rcv Hndshake = Xon/Xoff

Ptr Xmt Hndshake = Xon/Xoff

Ptr Rcv = Off

Rcv Hndshake = Xon/Xoff

Xmt Hndshake = Xon/Xoff

Comm Mode = FDX

XPC Handshake = On

Printer Selection = Off

Multiple Sessions = Off

Ethernet Mode = Off

Auto Connect = Off

Ethernet Node ID = (default}

For use with an Ethernet connection the following parameters need to be configured:

• Display Setup (F1 in setup mode)

Page Length = 1*Lines (only required if ‘Multiple Sessions=On’)

• Communications Setup (F4 in setup menu)

Multiple Sessions = Off or On

Ethernet Mode = On

Auto Connect = Off or On

‘Multiple Sessions=On’ should be set if multiple telnet sessions are required.

‘Auto Connect=On’ is used to prevent the need to press return to establish a telnet connection.

• LAN Setup (F9 in setup mode)

Local IP Address = IP address of the terminal

Netmask = Netmask value for the network

Gateway = gateway address if required by the network

Remote IP 0 Address = IP address of first server Port = 23

Remote IP 1 Address = IP address of second server Port = 23

….

Remote IP B Address = IP address of twelfth server Port = 23

Term Type = Same as personality specified in General Setup menu

Ethernet Node ID = leave at default value

Note: If only one host is being connected to, all twelve Remote IP addresses and ports should be set to the same value.

Note: Eight separate telnet sessions are allowed if any columns other than Econ-80 is selected in Terminal Display Set-

up. If Econ-80 is selected, the Multiple Sessions option allows twelve concurrent telnet sessions to be used.

Download from Www.Somanuals.com. All Manuals Search And Download.

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

2.2 Changing The Operating Parameters

To select one of the setup menus shown, press the indicated function key.

- The screen for that menu appears with the name highlighted.

- The fields in the middle of the screen indicate the parameters that can be changed in that menu.

- The top line identifies the keys to press to highlight the parameter fields and change the settings.

The procedure is: (1) Use arrow key to highlight the parameter field to be changed.

(2) Use the Spacebar to change the parameter.

<F12> always returns the user to the top menu.

The following tables list the parameters for each menu and explain their settings. Default settings are listed first

unless otherwise noted.

F1- Disp SETUP Menu

-----------------------------------------------------------------------------------------------------------------------------------------------------

Columns sets the screen display for 80 columns, 132 columns, or Econ-80 (80 columns with more pages of memory).

Lines sets the screen display for 24, 25, 42, or 43 lines. (24 lines are normally required for VT emulation, 25 lines for PC Term.)

Auto Page on causes a new page of memory to move onto the screen when the cursor reaches the top or bottom of the page.

Display CRT/LCD selects which kind of monitor be used. If LCD monitor is selected, the display columns only support 80

columns on Econ-80 columns. Must be set to LCD.

Cursor sets the cursor display to blink or steady, block or underline.

Background sets the screen display to Dark (light chars. on a dark background) or Light (dark chars. on a light background).

Width Change Clear causes the terminal to clear the screen when executing a command to change the number of columns.

Screen Saver OFF, 1, 2, 3, 4, 5, 6. Sets the screen saver to activate after the specified number of minutes.

Page Length sets the length of a page of display memory to:

•1 x Lines: Equal to the number of lines selected in the lines parameter (this value must be set when using multiple

sessions)

•2 x Lines: Two times the value of the lines parameter

•4 x Lines: Four times the value of the lines parameter, or

•*: Equal to the value of the lines parameter, with a second page containing the rest of the lines remaining in memory.

ANSI Reverse OFF/ON. Control function ANSI, VT-100 and VT-220:

• "OFF" means, when SGR command ESC [ 3? m and ESC [ 4? m select background and foreground color change

respectively.

• "ON" means, when SGR command ESC [ 3? m and ESC [ 4? m select foreground and background color change

respectively. (?

• can be 0,1,2,...,7)

F2- Genrl SETUP Menu

-----------------------------------------------------------------------------------------------------------------------------------------------------

Personality sets the terminal's operating mode to Wyse 325, Wyse 120/Wyse 60 (native mode), Wyse 50+ (WY-50, WY-50+,

WY-100, ADM 31/5/3a), TeleVideo TVI 925, TVI910+ (includes 910), ADDS A2, Digital Equipment VT-100, VT-220 7 bits,

VT-220 8 bits, VT-52, Console ANSI, PC TERM, PCG Alpha.

Scroll Speed sets the display scroll rate to Jump (the rate data is received), Smooth-8 (eight lines per second), Smooth-4,

Smooth-2, or Smooth-1.

Rcvd CR causes the cursor to move to the beginning of the current line (CR) or the beginning of the next line (CRLF) when the

terminal receives an ASCII CR.

Enhance allows the terminal to recognize an enhanced set of codes when the terminal is not in the native personality.

Auto Scroll causes the data to scroll up a line when the cursor moves past the last line of the page.

Monitor causes the terminal to display symbols for escape sequences and control codes without acting on them (test feature).

Status Line sets the top line of the screen as the status line.

Download from Www.Somanuals.com. All Manuals Search And Download.

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

End of Line Wrap causes the cursor to move to the start of the next line when additional characters are entered at the end of a

line.

Attribute sets display attributes to be assigned to each character as it is entered (Char), to be active to the end of the line (Line),

or to be active to the end of the page (Page).

-----------------------------------------------------------------------------------------------------------------------------------------------------

F3- Keybd SETUP Menu

-----------------------------------------------------------------------------------------------------------------------------------------------------

Keyclick sets the terminal to sound a muted beep each time a key is pressed or repeated.

Margin Bell sets the terminal's bell to ring when the cursor reaches the column where the bell is set (default is column 72 in 80-

column mode or 124 in 132-column mode).

NRC ON/OFF determines the communication and keyboard national character set.

DEL Keypad Dot/Del or Comma/Del. Determines whether numlock DEL generates dot or comma.

Key Repeat OFF, 1, .... ,8. Defines key repeat rate after a key has been depressed for about 1/2 second.

Language sets correct terminal operation for the language of the keyboard connected to it: US, UK, Danish, German, Spanish,

Swedish, Norwegian, Italian, French, Belgian, Swiss/French, and Swiss/German. Should be set to US.

Bell Volume OFF, 1, 2, 3 (3 different volumes)

Limit Xmt causes the terminal to send data through the HOST port as fast as the baud rate allows (None), or at a maximum rate

of 60 cps or 150 cps. In older systems limiting character rate is necessary to prevent loss of data.

Key Code sets the terminal to send normal ASCII characters (ASCII) or PC-type scan codes for every key up / down (Scan).

Scan is only required for the PC Term personality.

Num Start ON/OFF. When the terminal powers ON, this field determines whether the numeric pad starts as Numeric (NUM ON)

or Function (NUM OFF).

-----------------------------------------------------------------------------------------------------------------------------------------------------

F4- Comm SETUP Menu

-----------------------------------------------------------------------------------------------------------------------------------------------------

Baud Rate sets the host port baud rate to 50, 110, 134.5, 200, 300, 600, 1200, 2400, 4800, 7200, 9600, 19200, 38400, 57600,

76800, or 115200.

Rcv Hndshake allows the terminal to control the receipt of data from a device connected to the SERIAL1 port with no

handshaking (None), Xon / Xoff handshaking, DTR handshaking, DTR / Xoff handshaking

XPC Hndshake ON/OFF to set XPC code handshake, only possible when the personality parameter is set to PC Term.

Ethernet Mode ON/OFF to set the communication routing by Ethernet Network / or Serial Port.

Note: Set to ON when using Telnet and OFF when using serial port communication.

Data / Stop Bits through the SERIAL1 port, the terminal to send and receive 8-bits data with one stop bit or two stop bits, or 7-

bits data with one stop or two stops bits.

Xmt Handshake causes the terminal, when sending data to a device connected to the SERIAL1 port, to ignore all incoming

software handshaking signals (None) or to control data output in responds to Xon/Xoff handshaking.

Printer

Parallel : sends data to a parallel printer connected to the parallel port.

Serial : sends data to a serial printer connected to the serial 2 port.

OFF : ignores the print command.

Auto Connect OFF/ON selects whether a return character is required to establish an Ethernet connection.

Parity sets the terminal send data to the SERIAL1 (printer) port with none, odd, mark, even, or space parity.

Comm Mode sets the SERIAL1 port communication mode to full duplex (FDX), block (BLK), half duplex (HDX), or half duplex

block (HBLK).

Multiple Sessions defines whether an Ethernet connection supports multiple sessions function.

ON : indicates the terminal supports multiple sessions. Each session only has one display page. In 80 or 132 column mode, 8

simultaneous sessions are supported. In Econ-80 column mode, 12 simultaneous sessions are supported.

OFF : indicates the terminal only has single session. In this mode page length greater than one page can be defined.

_{Download from Www.Somanuals.com.}1_A0_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

-----------------------------------------------------------------------------------------------------------------------------------------------------

F5- Misc SETUP Menu

-----------------------------------------------------------------------------------------------------------------------------------------------------

Wprt Intensity sets the write protect attribute: normal, blank, dim, blank/dim.

Block End causes the terminal to send a block of data to the CPU with a line terminator as an ASCII US character and block

terminator as an ASCII CR character (US / CR), or with line terminators as ASCII CR and LF characters and the block terminator

as an ASCII ETX character (CRLF / ETX).

Ptr Parity causes the terminal to send the data to the SERIAL 2 (printer) port with none, odd, mark, even, or space parity.

Printer RCV ON/OFF

Wprt Reverse sets the write-protected characters to appear in reverse (dark characters on a light background).

Ptr Baud rate sets the SERIAL 2 (printer) port baud rate to 75, 150, 300, 600, 1200, 2400, 4800, 7200, 9600, 19200, 38400,

57600, 76800, 115200, 230400, 460800.

Ptr Rcv Hndshake sets the printer receive handshake through SERIAL 2 to be none, DTR, Xon / Xoff, DTR/Xoff .

Wprt Underline sets the write-protected characters to appear underlined.

Ptr Data/Stop Bits sets the data and stop bits through the SERIAL 2 (printer) port.

Ptr Xmt Hndshake sets the printer handshake to be none, DSR, Xon / Xoff, or Both .

-----------------------------------------------------------------------------------------------------------------------------------------------------

F6-Tabs SET-UP Menu

-----------------------------------------------------------------------------------------------------------------------------------------------------

On the tabs setup menu screen, the terminal's current tab stops are indicated by uppercase T's displayed along a line of periods

that mark each column position.

(1) A tab stop in columns 2 through 78 is shown as a T in the upper line of periods

(2) A tab stop in columns 79 through 132 is shown as a T in the lower line of periods

The user can easily determine where tabs are set by moving the cursor across the line and reading the column number displayed

on the right side of the screen. Clear and set tabs anywhere on the line, as follows:

(1) To move the cursor across the line, press < →> (right arrow) or < ←> (left arrow)

(2) To either clear or set (toggle) an individual tab stop at the cursor position, press <Spacebar>

(3) To clear all tabs, press <Home>

(4) To set tabs to the default setting (every eighth column), press <Backspace>

Note: A tab stop cannot be set to column 1.

-----------------------------------------------------------------------------------------------------------------------------------------------------

F7- FKeys SET-UP Definition Setup Menu

-----------------------------------------------------------------------------------------------------------------------------------------------------

The function keys and many of the editing keys can be redefined to send a unique character string of up to 64 characters. Keys

that are not programmed will send a default sequence, which is determined by the personality selected. Table 2 lists the

programmable keys.

To redefine a key:

1. Select the key to be redefined by pressing that key together with <Ctrl> . This highlights the key's definition field.

2. Press <↑ > (up arrow) to select the shifted or unshifted key definition field.

3. Enter the key definition (up to 62 characters) at the cursor position. Correct errors by pressing < ← >(left arrow) to delete

characters or <Home> to clear the definition.

4. If the user wants to change the key's direction, press <Enter> (on the numeric pad) until the desired choice appears.

Direction determines where the key data is transmitted:

- Remote: Sends data to the CPU only, regardless of the terminal's communication mode. (Until redefined, the

direction of all the programmable keys is remote.)

- Local: Sends data to the terminal only, regardless of the terminal's communication mode

- Normal: Sends data to the CPU and / or the terminal, depending on the terminal's communication mode

_{Download from Www.Somanuals.com.}1_A1_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Table 2- Programmable Keys

Enhanced PC-Style Keyboard

F1 through F12

(UP ARROW)

(DOWN ARROW)

(LEFT ARROW)

(RIGHT ARROW)

BACKSPACE

Enhanced PC-Style Keyboard

ENTER (Both ENTER keys are programmable)

ESCAPE

HOME

INSERT

PAGE DOWN

PAGE UP

PRINT SCREEN

TAB

DELETE

END

-----------------------------------------------------------------------------------------------------------------------------------------------------

F8- Ansbk SET-UP Menu

-----------------------------------------------------------------------------------------------------------------------------------------------------

A message of up to 20 characters can be programmed to identify the terminal to the CPU. Enter the message at the cursor

position. Correct errors by pressing <

> (left arrow) to delete characters or <Home> to clear the message.

CONCEAL hides the answerback message, so it is not displayed in setup mode.

To save the message in nonvolatile memory, exit Setup mode with the YES option.

-----------------------------------------------------------------------------------------------------------------------------------------------------

F9- Lan Setup Menu

-----------------------------------------------------------------------------------------------------------------------------------------------------

This menu configures the terminal for Ethernet communication. Use of Ethernet communications provides the additional ability to

open multiple sessions (applications) on one or more CPUs/servers at the same time. Support of these extended features requires

the server to be configured to accept telnet connections.

Note: The Ethernet option in the F4 setup menu must be set to ON for the terminal to work in an Ethernet environment.

Local IP Address is the IP address assigned to this terminal. This must be a unique IP address. An example of this address is

200.200.200.10.

Netmask is a value generated by the system based on the IP address. The system administrator would have this information. An

example is 255.255.255.0

Gateway This IP address is used to communicate with other networks. If a gateway is not being used this option should be blank.

Remote IP 0...B Address are for any remote CPU, or devices, that the terminal will communicate with for a specific session.

These twelve remote IP addresses should all be identical if all communications will be with only one CPU. If Multi-session-ON in

the F4 menu has been selected, and there is more than one CPU on the system, the user must specify which CPU each session

will communicate with. To communicate with a different CPU for a future session, these settings must be changed.

Note 1: The Multi-session option allows 8 separate sessions if any emulation other than ECON-80 is selected. If ECON-80

emulation is selected, the Multi-session option will then allow 12 separate sessions.

Note 2: Port 23 is the telnet service by default.

Note 3: The terminal must be powered cycled after saving for these parameters to take effect.

Term Type allows definition of the terminal with up to 40 characters. If Term Type is empty the default type is sent to the CPU

by the system.

Ethernet Node ID displays the serial number of the hardware Ethernet interface device. This is a default value of the

manufacturer of the hardware device and should not be changed.

-----------------------------------------------------------------------------------------------------------------------------------------------------

F10- Colr1 Set-up Menu

-----------------------------------------------------------------------------------------------------------------------------------------------------

Selects the color palette to be used for each screen attribute. A text sample of the selected color is displayed next to each

selection. Attribute selections are listed below.

Normal

Undl.

Dim

Undl. Blank

Blank

Undl. Blink

Blink

Blink Blank

Rev

Rev Blank

Rev Blink

Rev Blink Blank

Undl. Blink Blank

Undl. Rev

Undl. Rev Blank

Undl. Rev Blink

Undl. Rev Blink Blank

_{Download from Www.Somanuals.com.}1_A2_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

-----------------------------------------------------------------------------------------------------------------------------------------------------

F11- Colr2 Set-up Menu

-----------------------------------------------------------------------------------------------------------------------------------------------------

The color functionality differs with emulation. In general VT100, VT220 and ANSI Console work with applications, which control

the color directly. The remaining personalities associate colors based on existing monochrome video attributes. This section will

define parameter selection based on personality selected.

Background = Will determine the color of the background screen under some conditions (16 colors).

Normal F.G. \ Normal B.G. = These fields allow the user to select the character and background color (16 colors) for data

entered on the display before the application defines the color display remotely.

Border Color = The color of the border around the edge of the screen.

Cursor = Will select the color of the cursor (16 colors).

Intensity F.G. \ Intensity B.G. = These fields allow the user to select the character and background color (16 colors) for

data entered on the display as Dim in ASCII emulation's and Bold in VT\ANSI emulation's before the application defines the color

display remotely.

Attribute = Bold/Blink

Color mode = Is automatically selected based on the emulation selected.

Color map = Applies in WY325 mode only and determines if the monochrome attribute Reverse or Blank will be used to map

monochrome attributes to color.

Color Association = OFF/ON

Table 3- Color Setup Menu

Option

ASCII (NOT WY325)

WY325 *

VTXXX

ANSI CONSOLE

Background =

The whole data area of the

screen will be displayed in this

color, when the application

hasn't entered character or

spaces with the Normal or

Intensity B.G. color. Changes

in Background color will

affect Normal and Intensity

B.G. Any clear screen

No Function

Same as ASCII

commands will clear to this

color.

Cursor =

Normal F.G. =

Selects Cursor color

Selects color of Normal F.G.

Selects Cursor color

No Function

Selects Cursor color

Initial color selection

at power up

Selects Cursor color

Initial color selection

at power up

Normal B.G. =

Intensity F.G. =

Intensity B.G. =

Selects color of Normal B.G.

Selects color of Intensity F.G.

Selects color of Intensity B.G.

Automatic

No Function

Automatic

Initial color selection

at power up

Initial color selection

at power up

Initial color selection

at power up

Automatic

Initial color selection

at power up

Initial color selection

at power up

Initial color selection

at power up

Automatic

Color Mode =

Normal/Palette

Color Map =

No Function

See Above

No Function

* When the WY 325 personality is selected holding the Ctrl key down and depressing either the 0, 1, ..., 9 or (.) period keys in

the numeric pad change the assignment of color on the screen. Each selection is called a palette and is described in Table 4.

_{Download from Www.Somanuals.com.}1_A3_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Table 4- Color Palettes

Palette

Display Attribute

Foreground Color

Background Color

Normal

Green

Black

Reverse (or blank)_*1

Intensity_*2

Black

Blue

Yellow

Black

Blue

Black

Cyan

Black

Red

Intensity_*2and reverse (or blank)_*1

Underline

Underline and reverse(or blank)_*1

Underline and intensity_*2,*3

Underline, intensity, _*2and reverse (or blank)_*1

Normal

Black

Cyan

Black

Red

Black

Green

Black

Yellow

Black

Cyan

Black

White

Black

Cyan

Black

Red

Black

Red

Reverse (or blank)_*1

Black

Yellow

Black

Cyan

Black

White

Black

White

Black

Red

Intensity_*2

Intensity_*2and reverse (or blank)_*1

Underline

Underline and reverse (or blank)_*1

Underline and intensity_*2,*3

Underline, intensity, _*2and reverse (or blank)_*1

Normal

Reverse (or blank)_*1

Intensity_*2

Black

Magenta

Black

Blue

Intensity_*2and reverse (or blank)_*1

Underline

Black

Magenta

Black

Blue

Underline and reverse (or blank)_*1

Underline and intensity_*2,*3

Underline, intensity, _*2and reverse (or blank)_*1

Normal

Black

Cyan

Black

White

Black

Magenta

Black

Yellow

Black

Magenta

Black

Blue

Black

Blue

Reverse (or blank)_*1

Black

White

Black

Magenta

Black

Yellow

Black

Cyan

Black

Blue

Intensity_*2

Intensity_*2and reverse (or blank)_*1

Underline

Underline and reverse (or blank)_*1

Underline and intensity_*2,*3

Underline, intensity, _*2and reverse (or blank)_*1

Normal

Reverse (or blank)_*1

Intensity_*2

Black

Green

Black

Red

Intensity_*2and reverse (or blank)_*1

Underline

Black

Green

Black

Red

Underline and reverse (or blank)_*1

Underline and intensity_*2,*3

Underline, intensity, _*2and reverse (or blank)_*1

Normal

Black

Magenta

Black

White

Black

Green

Black

Cyan

Black

Yellow

Black

White

Black

Green

Black

Cyan

Reverse (or blank)_*1

Intensity_*2

Intensity_*2and reverse (or blank)_*1

Underline

Underline and reverse (or blank)_*1

Underline and intensity_*2,*3

Underline, intensity, _*2and reverse (or blank)_*1

_{Download from Www.Somanuals.com.}1_A4_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Table 4- Color Palettes (Cont'd)

Palette

Display Attribute

Foreground Color

Background Color

Normal

Yellow

Black

Reverse (or blank)_*1

Intensity_*2

Black

Red

Yellow

Black

Red

Black

Cyan

Black

Magenta

Black

Red

Yellow

Magenta

Black

Cyan

Black

Green

Black

White

Black

Red

Intensity_*2and reverse (or blank)_*1

Underline

Underline and reverse (or blank)_*1

Underline and intensity_*2,*3

Underline, intensity, _*2and reverse (or blank)_*1

Normal

Black

Cyan

Black

Magenta

Black

Red

Reverse (or blank)_*1

Black

Magenta

Black

Cyan

Black

Green

Black

White

Black

Red

Intensity_*2

Intensity_*2and reverse (or blank) _*1

Underline

Underline and reverse (or blank)_*1

Underline and intensity_*2,*3

Underline, intensity, _*2and reverse (or blank) _*1

Normal

Reverse (or blank)_*1

Intensity_*2

Black

Yellow

Black

Magenta

Black

White

Black

Yellow

Black

Blue

Intensity_*2and reverse (or blank)_*1

Underline

Black

Yellow

Black

Magenta

Black

White

Black

Yellow

Black

Blue

Black

Cyan

Black

Yellow

Black

Blue

Underline and reverse (or blank)_*1

Underline and intensity_*2,*3

Underline, intensity, _*2and reverse (or blank)_*1

Normal

Reverse (or blank)_*1

Intensity_*2

Intensity_*2and reverse (or blank)_*1

Underline

Underline and reverse (or blank)_*1

Underline and intensity_*2,*3

Black

Cyan

Black

Green

Black

Blue

Underline, intensity, _*2and reverse (or blank)_*1

10 (Soft Palette) Normal

(soft Reverse (or blank)_*1

palette) Intensity_*2

Black

Cyan

Black

Red

Intensity_*2and reverse (or blank)_*1

Underline

Black

Cyan

Black

Red

Underline and reverse (or blank)_*1

Underline and intensity_*2,*3

Underline, intensity, _*2and reverse (or blank)_*1

Black

*1. Whether the reverse or blank attribute is mapped to the colors shown depends on an escape sequence or the setting of

the Color Map setup parameter on the Attribute menu. The default is reverse. When the blank attribute is mapped, only the

background is visible.

*2. The intensity is dim in ASCII personalities and bold in ANSI personalities. (The intensity attribute is not supported in

the following personalities: Wyse 50+, ADDS A2, TVI 910+, TVI925, and VT52.) The attribute can be disabled by

an escape sequence or in setup mode (Intensity Attribute parameter).

*3. In each palette, the status line displays the same foreground and background colors as shown here for the underline-and-

intensity attribute.

_{Download from Www.Somanuals.com.}1_A5_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

3. LOCAL KEYBOARD COMMANDS

Table 5 lists local keyboard commands in the terminal's native mode.

Table 5- Local Keyboard Commands in Native Mode

Key Sequence by keyboard Style

Command

Enhanced PC

Toggle CAPS LOCK on/off

Toggle NUM LOCK on/off

Put terminal in SETUP mode

Partially reset terminal, including communication unlock

keyboard, turn off all print modes

CAPS LOCK

NUM LOCK

ALT ESC

ALT PAUSE

Send break_*1

BREAK_*2

Toggle between block and full-duplex modes

Print Screen formatted

SHIFT BREAK

PRINT SCREEN

Turn auxiliary print mode on/off

SHIFT SYS REQ_*3

CTRL SHIFT 1 (kpd)

CTRL

CTRL SHIFT

CTRL SHIFT HOME

CTRL 0kpd

Turn monitor mode on/off

Turn status line display on/off

Speed scrolling rate

Slow scrolling rate

Home cursor and clear page

Display page 0

Display page 1

CTRL 1kpd

PAGE DOWN

Display next page (or active other window) _*4

PAGE UP

Display previous page (or active other window) _*5

Toggle between split screen_*5and full screen format

CTRL SHIFT –kpd

ALT F1

Toggle Session 0_*6

ALT F2

Toggle Session 1_*6

ALT F3

Toggle Session 2_*6

ALT F4

Toggle Session 3_*6

ALT F5

Toggle Session 4_*6

ALT F6

Toggle Session 5_*6

ALT F7

Toggle Session 6_*6

ALT F8

Toggle Session 7_*6

ALT F9

Toggle Session 8_*6

ALT F10

ALT F11

ALT F12

CTRL SHIFT. Kpd

Toggle Session 9_*6

Toggle Session A_*6

Toggle Session B_*6

Close the active Session by Local Terminal_*6

*1. To MODEM port only when configured as data port: has no effect on AUX port.

*2. [BREAK] = [PAUSE] pressed together with [CTRL].

*3. [SYS REQ] = [PRINT SCREEN] pressed together with [CTRL].

*4. If screen is split.

*5. Splits screen at line 12.

*6. Only active at Ethernet mode ON.

_{Download from Www.Somanuals.com.}1_A6_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

4. CONNECTOR PIN ASSIGNMENT

Table 6- Serial Port (Serial 1) Connector Pin Assignments

(RS232C 9-pin connector)

Signal

Data carrier detect

Receive data

Mnemonic Direction

DCD In

RxD In

Transmit data

Data terminal ready

Signal ground

Data set ready

Request to send

Clear to send

TxD Out

DTR Out

SGND

DSR In

RTS Out

CTS In

Table 7- Serial Port (Serial 2) Connector Pin Assignments

(RS232C 9-pin connector)

Signal

Data carrier detect

Receive data

Mnemonic Direction

DCD In

RxD In

Transmit data

Data terminal ready

Signal ground

Data set ready

Request to send

Clear to send

TxD Out

DTR Out

SGND

DSR In

RTS Out

CTS In

Table 8- Printer Port Connector Pin Assignments

(Compatible with the IBM PC parallel port)

Signal

-Strobe

Mnemonic Direction

Out

Data bit 0

Data bit 1

Data bit 2

Data bit 3

Data bit 4

Data bit 5

Data bit 6

Data bit 7

-Acknowledge

Busy

Paper end

Slct

-Auto feed XT

-Error

-Init

-Slctn

18-25

Out

Ground

Table 9- 10Base T Connector Pin Assignments

(RJ45 8 pin female connector)

Signal

Direction

Transmit +

Transmit -

Receive +

Receive -

Out

_{Download from Www.Somanuals.com.}1_A7_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

5. COMMAND GUIDE

5.1 Commands Supported in ASCII Personalities

Table 5-1 lists all the ASCII commands recognized by the terminal. The native mode code for the command is given in the second

column. (The native mode includes WY-325,WY-120 and WY-60.) The remaining columns show the support for the command in

other ASCII personalities according to the following notations:

Same

Same as native code (code is native to other terminal also)

Wyse

Same as native code (Wyse enhancement- code not native to other terminal)

ENH

Same as native code when enhance mode is ON (Wyse enhancement - code not native to other terminal) A code listed under a

nonnative personality indicates that the related terminal's native code is supported.

A blank in any column indicates that the command is not supported.

Variables are shown in italics. Their values are listed in alphabetical order at the end of the table.

Footnotes are found at the end of Table 10 on page 20.

Table 10- Commands Supported in ASCII Personalities

Command

FUNCTION

Native

Mode

Wyse

WY-50+

ADDS

VP A2

TVI

910+/925

Term

Monitor Mode

Monitor mode on

Monitor mode off

ESC U

ESC u

or ESC X

Same

Selecting Personalities

Enhance mode off

Enhance mode on

Select WY-50+ mode

Select TVI 910+ mode

Select TVI 925 mode

Select ADDS VP A2 mode

Select Console ANSI mode

Select Native mode

ESC ~ SPACE Same

ENH

ESC v SPACE

ESC v !

ESC ~ !

ESC ~"

Same

Wyse

ESC v "

ESC ~ #

ESC ~ $

ESC ~ %

ESC ~ A

ESC ~ 4

ESC ~ 5

ESC ~ 6

ESC ~ ;

ESC v #

ESC v $

ESC v %

ESC v A

ESC v 4

ESC v 5

ESC v 6

ESC v ;

Select PC Term mode

Select VT52 mode

Select VT100 mode

Select PCGAPHIC mode_*1

Select VT220-7 mode

Select VT220-8 mode

ESC ~ I

ESC ~ <

ESC ~ =

Same

ENH

Wyse

ESC v I

ESC v <

ESC v =

Select WY-325 mode_*3

ESC ~ B

Same

ENH

Wyse

ESC v B

Communicating with the

computer

Enable transmission

Stop transmission Disconnect

Send ACK (if ACK mode on)

CTRL Q

CTRL S

CTRL E

Same

Wyse

Same

_{Download from Www.Somanuals.com.}1_A8_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Table 10- Commands Supported in ASCII Personalities (Cont'd)

Command

ADDS

FUNCTION

Native Mode

Wyse

TVI

WY-50+

VP A2

910+/925

Term

ACK mode off

ACK mode on

Full-duplex mode on

Half-duplex mode on

Block mode on

ESC e 6

ESC e 7

ESC C ESC D F

ESC C ESC D H

ESC B

Same

ENH

Same

ESC }

ESC {

Same

ESC C

ENH

Block mode off (conversation)

Half-duplex block mode on

Set Serial 1 port receive

handshaking protocol

Set Serial 1 port transmit

handshaking protocol

Set maximum data transmission

speed for host port

ESC D H ESC B

ESC c 2 hndshk

Same

ENH

ESC c 4 hndshk

Same

ESC c 6 max

Set Serial 1 port operating

parameters

Set Serial 2 port operating

parameters

ESC c 0 baud

stop parity word

ESC c 1 baud

stop parity word

Enable DTR Serial port 1

Handshaking

Enable X-on/X-off Serial port 1

Program answerback message

CTRL N

CTRL O

CTRL N

CTRL O

ENH

ESC c; answer

CTRL Y

Same

Conceal answerback message

Send answerback message

Turn answerback mode off

Turn answerback mode on

ESC c =

ESC c <

ESC e SP

ESC e !

Same

ENH

Controlling the Terminal and

Keyboard

Sound bell

CTRL G

Same

ENH

Same

ENH

CTRL B

CTRL D

ENH

Same

Select bell volume

Unlock keyboard

Lock keyboard

CAPS LOCK off

CAPS LOCK on

NUM LOCK off

ESC c \volume

CTRL N or ESC"

CTRL O or ESC#

ESC e '

ESC e &

ESC e @

ESC e A

ESC e B

ESC e C

ESC e $

ESC e %

ESC e L

ESC "

Same

ENH

ESC "

ESC #

ESC SP M

ESC SP L

ESC SP K

ESC SP J

ESC SP O

ESC SP N

ESC <

ESC >

ESC n

ESC o

NUM LOCK on

SCROLL LOCK off

SCROLL LOCK on

Keyclick off

Keyclick on

Margin bell off

ENH

Same

ESC <

ESC >

ENH

Margin bell on

ESC e M

ESC ' J

ESC e H

ENH

Set margin bell at curs position

Select standard ASCII key code

mode

Select PC scan code mode

Key repeat off

Key repeat on

ESC e I

ESC e ,

ESC e -

Same

ENH

Read keyboard status

ESC [

Redefining the keys

Clear function key definition

ESC z fkey

DEL

Same

Clear key direction and definition ESC Z dir

key/fkey DEL

ENH

_{Download from Www.Somanuals.com.}1_A9_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Table 10- Commands Supported in ASCII Personalities (Cont'd)

FUNCTION

Native Mode

Wyse

WY-50+

ADDS

VP A2

TVI

910+/925

Term

-Program function key definition

ESC z fkey

sequence DEL

ESC Z dir

Same

ENH

Program key direction and

definition

Wyse

ESC | p1 p2

sequence

key/fkey

sequence DEL

CTRL Y

Read key direction and definition ESC Z ~key

Same

or ESC Z ~fkey

Screen and Cursor Display

Screen display off

Screen display on

Screen saver off

Screen saver on

Set reverse screen

ESC ` 8

ESC ` 9

ESC e P

ESC e Q

ESC ^ 1

Same

ENH

ESC o

ESC n

ENH

ESC b

ESC O

ESC N

Restore normal screen

Set scrolling speed and type

ESC ^ 0

ESC ` scroll

Same

ENH

ESC d_*4

Smooth scrolling on

ESC 8_*5

ESC 9_*5

ESC . cursor1 ESC.cursor1

Smooth scrolling off

Set cursor display features

Cursor display off

ESC ` cursor

ESC ` 0

ESC ` 1

Same

ENH

CTRL W

CTRL X

Cursor display on

25th line display off

ESC e

Displaying the Message Fields

Extended status line on

Standard status line on

Status line off

Program/display CPU message

on status line

ESC ` a

ESC ` b

ESC ` c

ESC F

Same

ENH

message CR

Program CPU message on

ESC z ( text

Same

ENH

ESC f_*5

ESC f

unshifted lable line_*6

Program CPU message on shifted ESC z ) text

text CR

label line

Turn off shifted label line

Clear unshifted label line

Clear shifted label line

ESC z DEL

ESC z ( CR

ESC z ) CR

Same

ENH

Program/display function key label ESC z field

label CR

Clear function key label

ESC z field

Same

ENH

Defining the data Area

Select 80-column display

ESC ` :

ESC ` ;

ESC e F

ESC e G

ESC e .

ESC e /

Same

ENH

Select 132-column display

Economy 80-column mode off

Economy 80-column mode on

Width-change-clear mode off

Width-change-clear mode on

Display 24 data lines_*7

Display 25 data lines_*7

ESC e (

ESC e )

Same

ENH

ESC ^

_{Download from Www.Somanuals.com.}2_A0_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Table 10- Commands Supported in ASCII Personalities (Cont'd)

FUNCTION

Native Mode

Wyse

WY-50+

ADDS

VP A2

TVI

910+/925

Term

Display Memory/Split Screen

Divide memory into pages

Display previous page

ESC w length

ESC w B or ESC J_*8

Same

ENH

ESC J

ESC K

Display next page

Display page n

Split screen horizontally

(simple split)

ESC w C or ESC K_*8

ESC w page

ESC x A line

Same

ENH

Split screen horizontally

(simple split) and clear pages

Split screen horizontally

(adjustable split) and clear pages

Split screen horizontally

(adjustable split)

ESC x 1 line

ESC x 3 line

ESC x C line

Same

Activate upper window

Activate lower window

ESC ]

ESC }

Same

Activates other window (or page _*8) ESC J or ESC K

Same

ESC J_*5

Lower horizontal split

ESC x P

ESC x R

ESC w E

ESC w F

ESC x @

ESC x 0

Raise horizontal split

Roll window up in page

Roll window down in page

Redefine screen as one window

and clear pages

Display Attributes

Assign display attribute to a

message field

Assign character display attribute ESC G attr

ESC A mf attr

Same

ESC \_*4

ENH

Same

Character attribute mode off

Character attribute mode on

Page attribute mode on

Line attribute mode on

Assign write-protected character

display attribute

ESC e 0

ESC e 1

ESC e 2

ESC e 3

ESC `wpca

Same

ESC 0 wpca1

Wyse

Clear unprotected page to

display attribute

ESC !

ENH

attr

Assign line attribute

ESC G lattr

Same

ENH

Redefine color map values_*9

ESC d y

fcolor

bcolor map

Set tag protect attribute

Reset tag protect attribute

CTRL N

CTRL O

Select a predefined color palette_*9ESC d z

palette

Map blank attribute_*9

ESC d {

ESC d |

Map reverse attribute_*9

Protecting Data

Write-protect mode off

Write-protect mode on

Clear cursor column to

write-protected spaces

Protect mode off

ESC (

ESC )

ESC V

Same

CTRL O

CTRL N

ENH

Same

ESC ,

ESC &

Same

ENH

Same

Wyse

Same

Protect mode on

_{Download from Www.Somanuals.com.}2_A1_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Table 10- Commands Supported in ASCII Personalities (Cont'd)

FUNCTION

Native Mode

Wyse

WY-50+

ADDS

VP A2

TVI

910+/925

Term

Graphics Characters

Graphics mode on

Graphics mode off

Display graphics character

ESC H

ESC H ldraw

CTRL B

CTRL C

Same

ESC $

ESC %

ESC $

ESC %

Controlling the Cursor

Cursor left (backspace)

CTRL H

Same

or CTRL U

Cursor right

Cursor up; no scroll

CTRL L

CTRL K

Same

CTRL F

CTRL Z

Same

Cursor up; scroll (reverse linefeed) ESC j

Cursor down; no scroll

Same

ENH

Same_*10

CTRL V

Same

CTRL V

Same

Cursor down; scroll (Linefeed)

Cursor to start of line

Cursor to start of next line

Home cursor

CTRL J

CTRL M

CTRL _

ESC {

Same

ENH

Wyse

CTRL ^

or CTRL ^

or CTRL A

Same

Cursor to specific column

Cursor to specific line

End-of-line wrap off

CTRL P col

CTRL K line

ENH

or ESC Y

ENH

ESC ] _*11

ESC [

ESC d .

ESC d /

Same

ESC 0

ESC ~

ESC 9

ESC 8

End-of line wrap on

Received CR mode off

Received CR mode on

Autopage mode off

ESC e 4

ESC e 5

ESC d *

ESC d +

ESC N

ESC O

ESC = line

col

ENH

ESC w

ESC v

Autopage mode on

Autoscrolling mode off

Autoscrolling mode on

Address cursor in current

80-column page

Address cursor in specific

80-column page

Same

ESC w @ page

line col

ESC - wnd/

Same

ESC - page

line col

Address cursor in specific

ENH

80-column window/page_*8

Address cursor in specific

80/132-column current page

Read cursor line and column

address in 80-column current

page

Read 80-column page number

and cursor address

Read 80-column window/page

number and cursor address

Read cursor address in 80/132-

column page

page line col

ESC a lll R

ccc C

Same

ENH

Same

ESC ?

Same

ESC w

ESC /

ESC b

Same

ENH

Same

Editing

Clear all tab stops

Set tab stop

Clear tab stop

Tabulate cursor

Backtab

ESC 0

ESC 1

ESC 2

ESC i or CTRL I

ESC I

Same

ENH

ESC 3

Same

CTRL I

Same

ESC I

ENH

ESC 3

Same

CTRL I

Same

ESC i

ESC Z

Same

Field tab

Insert mode on, replace mode off ESC q

Insert mode off, replace mode on ESC r

Insert space character

Same

ENH

Same

ESC Q

_{Download from Www.Somanuals.com.}2_A2_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Table 10- Commands Supported in ASCII Personalities (Cont'd)

FUNCTION

Native Mode

Wyse

WY-50+

ADDS

VP A2

TVI

910+/925

Term

Editing (Cont'd)

Insert line of spaces

Delete cursor character

Delete cursor line

ESC E

ESC W

ESC R

Same

ENH

ESC l

Same

Clearing Data

Clear page to nulls

Clear page to spaces

Clear page to write-protected

spaces

ESC *

ESC +

ESC ,

Same

ENH

Same

Clear unprotected page to spaces ESC ; or CTRL Z

Same

ESC ;

ENH

ESC ;

or ESC +

Same

Clear unprotected page to nulls

Clear unprotected page to

a specific character

ESC :

ESC .char

Same

Clear unprotected page to

protected spaces

Clear unprotected page to

display attribute

Clear unprotected page to spaces ESC Y

from cursor

Clear unprotected page to nulls

from cursor

Clear unprotected line to spaces

from cursor

Clear unprotected line to nulls

from cursor

ESC ,

ENH

ESC ! attr

Same

ENH

ESC k

ENH

Same

ESC F

ESC y

ESC T

ESC t

Same

ESC K

ENH

Same

Fill page with H's

Sending data

Begin print / send at top of page

Begin print / send at top of screen ESC d&

Send cursor character

Send line through cursor

Send unprotected line through

cursor

ESC d'

Same

ENH

ESC M

ESC 6

ESC 4

Same

ESC 6

ESC 4

Send page through cursor

Send unprotected page through

cursor

ESC 7

ESC 5

Same

ENH

Same

ESC 5

ESC 7

Mark block beginning

Mark block end

Send entire block

ESC 8

ESC 9

ESC s

ESC S

Same

ENH

Same

ESC [

ESC D

Send unprotected

Report terminal status

Report attribute under cursor

_{Download from Www.Somanuals.com.}2_A3_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Table 10- Commands Supported in ASCII Personalities (Cont'd)

FUNCTION

Native Mode

Wyse

WY-50+

ADDS

VP A2

TVI

910+/925

Term

Print Functions

Print formatted page

Print formatted unprotected page ESC @

ESC P

Same

ENH

Same

Print unformatted page

Select Parallel printer

Select Serial printer

ESC p or ESC L

ESC d (

ESC d )

CTRL T

CTRL R

CTRL T

ESC d #

ESC d $

ESC d %

ESC d SPACE

ESC d !

Same

ESC p

Same

ESC 4

ESC 3

ESC L_*11

Auxiliary print mode off

Auxiliary print mode on

Transparent print mode off

Transparent print mode on

Bi-directional mode off

Bi-directional mode on

Auxiliary receive mode off

Auxiliary receive mode on

Set print terminator

ESC A

ESC @

ESC a

ESC `

CTRL T

CTRL

ESC A

ESC a

ESC `

CTRL T

CTRL R

ESC p

ESC x

ESC p

ESC x

Define delimiters

Character Sets

Select primary character set

Select secondary character set

Define primary character set

Define secondary character set

Load font bank with predefined

ESC c D

ESC c E

ESC c B bank

ESC c C bank

ESC c @ bank

set

Same

Clear font bank

Define and load character

ESC c ? bank

ESC c A bank

pp bb...bb

CTRL Y

Same

*1. PCG ALPHA in Mono. Text Model machine.

*3. Valid only in Color Model machine.

*4. With enhance mode off.

*5. With enhance mode on.

*6. Automatically display in native mode. May be hidden by assigning blank attribute (ESC A l l).

*7. Screen cleared.

*8. If screen is not split.

*9. In WY-325 only

*10. In TeleVideo 925 only

*11. In TeleVideo 910+ only

_{Download from Www.Somanuals.com.}2_A4_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

5.2 Variable Values for Table 10 Commands

answer Up to 20 characters to define answerback message

attr

Display Attributes

attr

Display Attributes

SPACE

Space character

Normal

Blank

Blink

Blink and Blank

{

Dim

Dim and invisible

Dim and blink

Dim, blink, invisible

Dim and reverse

Reverse

Dim, reverse, invisible

Dim, reverse, blink

Dim, reverse, blink invisible

Dim and underline

Dim, underline, invisible

Dim, underline, blink

Dim, underline, blink invisible

Dim, underline, reverse

Dim, underline, reverse invisible

Dim, underline, reverse blink

Dim, underline, reverse blink, invisible

Reverse and invisible

Reverse and blink

Reverse, blink, invisible

Underline

Underline and invisible

Underline and blink

Underline, blink, invisible

Underline and reverse

Underline, reverse, invisible

Underline, reverse, blink

Underline, reverse, blink invisible

;

}

DEL

bank

Font Bank_*a

Font bank 0

Font bank 1

Font Bank_*a

Font bank 2

Font bank 3

*a Holds predefined character set

baud

Baud Rate

115200

76800

57600

38400

baud

Baud Rate

19200

9600

7200

4800

baud

Baud Rate

2400

1200

600

300

baud

Baud Rate

200

134.5

110

bb...bb 32-byte character string defining bit pattern of character

bcolor

Background Color

bcolor Background Color

Black

Bue

Green

Cyan

Red

Magenta

Yellow

White

ccc One-to three-decimal value of column relative to home

char Character that replaces unprotected characters

col See line/col

color

Black

Bue

Green

Cyan

Red

color

Magenta

Yellow

White

Dim blue

Dim green

color

Dim cyan

Dim red

Dim magenta

Dim yellow

Dim white

cursor Cursor Display

Cursor display off

Cursor display on

Steady block cursor

Blinking line cursor

Steady line cursor

Blinking block cursor

dir

Direction

Normal

Remote

Local

_{Download from Www.Somanuals.com.}2_A5_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Variable Values for Table 10 Commands (Cont'd)

fcolor

Foreground Color

Black

Bue

Green

Cyan

fcolor

Foreground Color

Red

Magenta

Yellow

White

Function field

field

Function field

field

Key

unshifted shifted

Key

F10

F11

F12

unshifted shifted

[

;

Function fkey

fkey

Function fkey

fkey

Key

unshifted shifted

Key

F10

F11

F12

unshifted shifted

hndshk

Handshaking Protocol

Transmit

Receive

None (default)

XON/XOFF

DTR

None (default)

XON/XOFF

Both

Keyboard Style

key

Enhanced PC

key

Enhanced PC

key

Enhanced PC

RETURN

SPACE ESC

SHIFT TAB →

← BACKSPACE

SHIFT← BACKSPACE

SHIFT →

)

SHIFT ESC

SHIFT RETURN

HOME

TAB →

SHIFT HOME

SHIFT DELETE

PRINT SCREEN

SHIFT PRINT SCREEN

END

↑

ENTER kpd

SHIFT ↑

SHIFT ENTER kpd

INSERT

↓

SHIFT ↓

←

SHIFT ←

→

SHIFT INSERT

PAGE DOWN

SHIFT PAGE DOWN

DELETE

]

SHIFT END

PAGE UP

;

SHIFT PAGE UP

label 9 characters (80 columns); 7 characters (132 columns)

lattr

Line Attribute

Single-high, single-wide characters

Single-high, double-wide characters.

Top half of double-high, single-wide characters

Bottom half of double-high, single-wide characters

Top half of double-high, double-wide characters

Bottom half of double-high, double-wide characters

ldraw Graphics

Idraw

Graphics

Idraw

Graphics

Idraw

Graphics

Character

┬

└

┌

┐

├

┘

│

┼

┤

─

┴

□

█

;

_{Download from Www.Somanuals.com.}2_A6_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Variable Values for Table 10 Commands (Cont'd)

length Multiple

Length of Page

1xlines

2xlines

Equal to the number of data lines

Double the number of data lines

I_*b

4xlines

Four times the number of data lines

*b Available only in WY-50+ personality.

Line/Column

line/col_*c

Space

;

[

{

}

(

)

]

DEL/RUB

*c Native codes also recognized in WY-50+, TVI 910+/925, and PC Term personalities, and in ADDS VP A2 personality absolute

cursor addressing.

lll One- to three-decimal value of line relative to home

map

Definition

map

Definition

Normal

Underline

Reverse (or blank_*d)

Intensity

Underline and reverse (or blank_*d)

Underline and intensity

Intensity and reverse (or blank_*d)

Underline, intensity, and reverse (or blank_*d)

*d. Colors mapped to reverse or blank depending on the setting of the Color Map setup parameter or the equivalent

escape sequences.

Max

Maximum Speed

60 characters per second

No limit (default)

150 characters per second

message 46 characters (80 columns); 98 characters (132 columns)

Screen Area_*e

Data area

Function key label line

Screen Area_*e

Terminal message field

Computer message field

*e In native mode, only the reverse attribute can be assigned to the data area.

_{Download from Www.Somanuals.com.}2_A7_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Variable Values for Table 10 Commands (Cont'd)

Function Key

F10

Function Key

Remote

Local

Normal

Page

page 0

page 1

page 2

page 3

page 4

page 5

page 6

In the 80 columns mode: There have 4 pages of display memory.

In the 132 columns mode: There have 3 pages of display memory.

In the Econ-80 columns mode: There have 7 pages of display memory.

Palette

Color Pallette

Palette 0

Palette 1

Palette 2

Palette 3

Palette

Color Pallette

Palette 4

Palette 5

Palette 6

Palette 7

Palette

Color Pallette

Palette 8

Palette 9

Palette 10

Parity

Parity Bits

None

Odd

Parity

Parity Bits

Mark

Even

pp 2-byte hex value of character position_*f.

*f In the illustrations, DEC = decimal value; HEX = hexadecimal value. Read across, then down.

Scroll

Scrolling Type

Jump scroll

Smooth scroll

Speed (lps)

sequence Up to 64 bytes to be loaded in function key

Set

Predefined Character Set

Native Mode

PC Multinational

Standard ASCII

PC Standard

Standard ANSI

Stop

stopbits

text 78 characters (80 columns); 130 characters (132 columns)

Volume BELL Volume

Volume

BELL Volume

“

Loud

Medium

Low

Off

_{Download from Www.Somanuals.com.}2_A8_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Variable Values for Table 10 Commands (Cont'd)

wnd/page Window or Page

Page 0 or upper window

Page 1 or lower window

Word

Data Word

7 bits

8 bits

wpca

Write-Protected Display Attribute wpca Write-Protected Display Attribute

Invisible on

Underline on

Reverse on

Dim on

Reverse_*g

Dim_*g

Normal_*g

Blink on

*g Clears other write-protected attributes

wpca1

Display Attribute

Normal

Dim

Blink

Dim/Blink

Invisible

Reverse (Rev)

Rev/Dim

wpca1

[

Write-Protected Display Attribute

Normal

Dim

Blink

Dim/Blink

Invisible

Reverse (Rev)

Rev/Dim

Rev/Blink

Rev/Dim/Blink

Rev/Invisible

Underline (UL)

UL/Dim

Rev/Dim/Blink

Rev/Invisible

Underline (UL)

UL/Dim

UL/Blink

UL/Dim/Blink

UL/Rev

UL/Rev/Dim

UL/Rev/Blink

UL/Rev/Dim/Blink

{

UL/Dim/Blink

UL/Rev

UL/Rev/Dim

UL/Rev/Blink

UL/Rev/Dim/Blink

6. ANSI COMMAND GUIDE

6.1 VT100, VT220 and Console ANSI Command Guide

Supported VT100,VT220 and Console ANSI Commands

Command

FUNCTION

VT100, VT220

Console ANSI

Controlling Functional modes_*1

Lock keyboard

Unlock keyboard

CSI 2 h

CSI 2 l

Same

Monitor mode on _*2

Monitor mode off

Insert mode on

Insert mode off

Local echo off

Local echo on

New line mode on

New line mode off

Cursor keys send application-dependent codes

Cursor keys send cursor movement codes

VT100 mode on

VT52 mode on

National character set mode on

National character set mode off

CSI 3 h

CSI 3 l

CSI 4 h

CSI 4 l

CSI 12 h

CSI 12 l

CSI 20 h

CSI 20 l

CSI ?1 h

CSI ?1 l

CSI ?2 h or CSI 61 "p

CSI ?2 l

Same

CSI ?42 h

CSI ?42 l

_{Download from Www.Somanuals.com.}2_A9_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Supported VT100, VT220 and Console ANSI Commands, Cont'd

Command

Console ANSI

FUNCTION

VT100, VT220

CSI ?3 h

CSI ?3 l

132-column display

Same

80-column display

Smooth scrolling on

Jump scrolling on

CSI ?4 h

CSI ?4 l

CSI ?5 h

CSI ?5 l

CSI ?6 h

CSI ?6 l

CSI ?7 h

CSI ?7 l

Reverse screen video on

Normal screen video on

Line 1 is top of scrolling region

Line 1 is top of display area

Autowrap on

Autowrap off

Autorepeat on

Autorepeat off

Block mode on

CSI ?8 h

CSI ?8 l

CSI ?10 h

CSI ?10 l

CSI ?18 h

CSI ?18 l

CSI ?19 h

CSI ?19 l

CSI ?25 h

CSI ?25 l

CSI 30 h

CSI 30 l

CSI 31 h

CSI 31 l

CSI 32 h

CSI 32 l

CSI 33 h

CSI 33 l

CSI 34 h

CSI 34 l

CSI 35 h

CSI 35 l

CSI 37 h

CSI 37 l

CSI 38 h

CSI 38 l

CSI 40 h

CSI 40 l

CSI 54 h

CSI 54 l

CSI 62;2"p

CSI 62;1"p

ESC space G

ESC space F

Block mode off

Send form feed after print screen operation

No form feed sent after print screen operation

Print full screen

Print scrolling region

Display cursor

Cursor off

Blank screen

Display screen

Display status line

Blank status line

Screen saver

Screen saver off

Cursor steady (nonblinking)

Cursor blinking

Underline cursor on

Block cursor on

Don't clear screen after width change

Clear screen after width change

Send erasable and nonerasable characters

Send only erasable characters

Send full screen

Send scrolling region

Turn 25th line on

Turn 25th line off

Select standard ANSI key codes

Select PC scan codes

VT220 8-bit mode on

VT220 7-bit mode on

8-bit transmission mode on (VT220)

7-bit transmission mode on (VT220)

Select next page

Select preceding page

Select page 0

CSI U

CSI V

CSI 0 z

CSI 1 z

Select page 1

Character Set Selection

ESC Ps final

Same

(

)

Label assigned

G2 (VT220 only)

G3 (VT220 only)

_{Download from Www.Somanuals.com.}3_A0_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Supported VT100, VT220 and Console ANSI Commands (Cont'd)

final

Final character

final

Final character

Designating DEC supplemental(VT220 only)

DSCS Designating Down-line loadable character set

Designating UK ANSI character set

Designating ASCII character set

Designating DEC special graphics

* DSCS can consist of zero, one or two intermediate character and a final character. Intermediate characters are

in the range of 2/0 to 2/15. Final characters are in the range of 3/0 to 7/14

Command

FUNCTION

VT100, VT220

Console ANSI

Load G0 character set into GL

Load G1 character set into GL

Load G1 character set into GR

Load G2 character set into GL

Load G2 character set into GR

Load G3 character set into GL

Load G3 character set into GR

CTRL O

CTRL N

ESC ~

ESC n

ESC }

Same

ESC o

ESC |

Shift G2 character set into GL for one character only ESC N

Shift G3 character set into GL for one character only ESC O

Controlling Character, Field, and Line Attributes

Define character attributes_*3

CSI Ps m (see table below)

Same

Select Graphic Rendition

(Console ANSI mode only)

CSI ps m (see table below)

Set bold background bit

ESC[ =PnE

same

Pn = 0: set bit 7 of attribute byte as B/G intensity

1: set bit 7 of attribute byte as B/G blink

Set normal foreground color

Set normal background color

Set reverse foreground color

Set reverse background color

Set graphic foreground color

Set graphic background color

Set border color

ESC[ = Psn F (see table,

ESC[ = Psn G next page)

ESC[ = Psn H

ESC[ = Psn I

ESC[ = Psn J

same

ESC[ = Psn K

ESC[ = Psn A

Values for “ Ps” (above)

Character Attribute

Normal (all attributes off)

Bold (blank off)

Underline

Blink

Reverse

Blank (bold off)

Normal intensity

Underline off

Blink off

Reverse off

Blank off

Character Attribute

Brown character (Bold on = Yellow)

Blue character

Magenta character

Cyan character

White character

Black background

Red background

Green background

Brown background (Bold on = Yellow)

Blue background

Magenta background

Cyan background

Black character

Red character

Green character

White background

Values for “ps” (above)

Function

Select Primary Font

Select First Altemate Font. Allows ASCII characters less than 32 to be displayed as ROM character.

Select Second Alternate Font. Toggles high bit of extended ASCII code before displaying as ROM character.

_{Download from Www.Somanuals.com.}3_A1_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Supported VT100, VT220 and Console ANSI Commands (Cont'd)

Values for “Psn” in table on page 56

Psn

Color

Black

Blue

Green

Cyan

Psn Color

Psn

Color

Lt. Red

Lt. Magenta

Yellow

Lt. White

Red

Gray

Magenta

Brown

White

Lt.Blue

Lt. Green

Lt. Cyan

Command

FUNCTION

VT100, VT220

Console ANSI

Access alternate graphic set

Define erasable character

Define non-erasable character

Define top half of double-high, double-wide line

Define bottom half of double-high, double-wide line ESC # 4

Define single-high, single-wide line

Define single-high, double-wide line

Define top half of double-high, single-wide line

Define bottom half of double-high, single-wide line

CSI Png

Same

CSI 0 "q or CSI 2 "q

CSI 1 "q

ESC # 3

ESC # 5

ESC # 6

ESC # :

ESC # ;

Controlling the Cursor

Display cursor

Cursor off

Cursor steady (nonblinking)

Cursor blinking

Underline cursor on

CSI ?25 h

CSI ?25 l

CSI 33 h

CSI 33 l

CSI 34 h

CSI 34 l

CSI ?1 h

CSI ?1 l

CSI n G or CSI n `

CSI n A

CSI n B or CSI n e

CSI n C or CSI n a

CSI n D

CSI n E

CSI n F

Same

Block cursor on

Cursor keys send application-dependent codes

Cursor keys send cursor movement codes

Move cursor to n column

Move cursor up n lines

Move cursor down n lines

Move cursor right n columns

Move cursor left n columns

Move cursor down cursor n line to column 1

Move cursor up n lines to column 1

Move cursor to line n

CSI n d

Move cursor to line n1, column n2

CSI n1; n2 H

or CSI n1; n2 f

IND

or ESC D

CTRL J

or CTRL K or CTRL L

or ESC M

NEL or ESC E

ESC 7

Move cursor down one line in current column,

scroll up if at bottom line

Move cursor down one line in current column,

execute CR if linefeed mode is on

Move cursor up one line in current column,

scroll down if at top line

Move cursor down one line to column 1

Save display attributes, cursor position, character

sets,wrap flag and origin mode status

Restore last saved display attributes, cursor position, ESC 8

character set, wrap flag, and origin mode status

Backspace cursor

Move cursor to next tab stop

Move cursor to column 1 of current line

or CSI s

or CSI u

CTRL H

CTRL I

CTRL M

Editing Functions

Erase from cursor to end of display

Erase from start of display to cursor

Erase entire display

Erase from cursor to end of line

Erase from start of line to cursor

Erase entire line

CSI 0 J

CSI 1 J

CSI 2 J

CSI 0 K

CSI 1 K

CSI 2 K

CSI ?0 J

Same

Erase erasable characters from cursor to

end of display

_{Download from Www.Somanuals.com.}3_A2_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Supported VT100, VT220 and Console ANSI Commands (Cont'd)

Command

Console ANSI

FUNCTION

VT100, VT220

Editing Functions (Cont'd)

Erase erasable characters from start of display

to cursor

Erase erasable characters in entire display

Erase erasable characters from cursor to end of line CSI ?0 K

Erase erasable characters from start of line

to cursor

CSI ?1 J

CSI ?2 J

Same

CSI ?1 K

Erase erasable characters from entire line

Erase n characters beginning at cursor

Insert n blank characters beginning at cursor

Insert n blank lines beginning at cursor line

Delete n line beginning at cursor line

Delete n characters beginning at cursor

CSI ?2 K

CSI n X

CSI n @

CSI n L

CSI n M

CSI n P

Same

Controlling Margins

Set top/bottom margins of scrolling

CSI t;b r

Same

t: Top line number

b: Bottom line number (optional; if omitted, treated

as bottom screen line)

Controlling Tabs

Clear tab stop at cursor

Clear all tab stops

Set tab stop at cursor

Set tab stop every 8th column

Move forward n tab stops

Move backward n tab stops

Move cursor to next tab stop

CSI 0 g or CSI 2 W

CSI 3 g or CSI 5 W

CSI 0 W or ESC H

CSI ?5 W

CSI n I

CSI n Z

CSI 2W

CSI 5W

Same

CTRL I

Controlling Scrolling

Smooth scrolling on

Jump scrolling on

CSI ?4 h

CSI ?4 l

CSI 0 z

CSI 1 z

CSI 2 z

CSI 3 z

CSI 4 z

Same

Set 0 lps smooth scrolling speed

Set 1 lps smooth scrolling speed

Set 2 lps smooth scrolling speed

Set 4 lps smooth scrolling speed

Set 8 lps smooth scrolling speed

Program function keys

DCS c;kl |

ESC Q Fn

(see tables below an on next page for values)

kc/hc ST

"string"

Program function key values in VT100 mode:

Clear

Key Lock

Clear all key definitions

Lock key definitions

Clear keys only as they are redefined

Don't lock key definitions

Shifted function key

F10

F11

F12

_{Download from Www.Somanuals.com.}3_A3_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Supported VT100, VT220 and Console ANSI Commands, Cont'd

Unshifted function key

F10

F11

F12

hc Hexadecimal representation of character string assigned to the function key.

Note: Multiple function key definitions can be programmed by entering the <kc>/<hc> parameters for each, separated by

semicolons (;).

Program function key values (from previous page) in Console ANSI mode:

Redefine keys with string

Function: Define Specific Programmable Function key or Numeric keypad with String.

Format: ESC Q Fn “ string “

Values of Fn for Programmable Function keys

Value

F Key

Value

F Key

Value

F Key Fn

Value

F Key

S_F1

S_F2

S_F3

S_F4

S_F5

S_F6

S_F7

S_F8

S_F9

S_F10

S_F11

S_F12

C_F1

C_F2

C_F3

C_F4

C_F5

C_F6

C_F7

C_F8

C_F9

C_F10

C_F11

C_F12

C_S_F1

C_S_F2

C_S_F3

C_S_F4

C_S_F5

C_S_F6

C_S_F7

C_S_F8

C_S_F9

C_S_F10

C_S_F11

C_S_F12

[

]

F10

F11

F12

;

Values of Fn for Numeric Keypad keys

Numeric Fn

Numeric

Value

Keypad

Value

Keypad

Value

Keypad

Value

Keypad

Key

Notes:

1. The string should not include the delimiter, or unexpected conditions maybe occur.

2. The defined contents of F1 ~F12 will be transmitted out by keying F1~F12.

The defined contents of S_F1~S_F12 will be transmitted out by multi-keying the Shift and Function key.

The defined contents of C_F1~C_F12 will be transmitted out by multi-keying the Ctrl and Function key.

The defined contents of C_S_F1~C_S_F12 will be transmitted out by multi-keying the Ctrl, Shift and Function key.

Example: Define Function Key F1 to the character ABC123: ESC Q 0"ABC123"

_{Download from Www.Somanuals.com.}3_A4_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Supported VT100, VT220 and Console ANSI Commands (Cont'd)

Command

Console ANSI

FUNCTION

VT100, VT220

Auxiliary Keypad Modes

Auxiliary keypad numeric mode on

Auxiliary keypad application mode on

ESC >

ESC =

Same

Transmission/Printer Control

Transmit through cursor position

Transmit to end of line or end of display

Send form feed after print screen operation

No form feed sent after print screen operation

Print full screen

Print scrolling region

Print screen

Send screen

Transparent print mode off

Transparent print mode on

PR port receive mode off

PR port receive mode on

Select parallel printer

Select serial printer

Print line

Send line

Copy print mode off

CSI 16 h

CSI 16 l

CSI ?18 h

CSI ?18 l

CSI ?19 h

CSI ?19 l

CSI 0 i or CSI i

CSI 2 i

CSI 4 i

CSI 5 i

CSI 6 i

CSI 7 i

Same

CSI 8 i

CSI 9 i

CSI ?1 i

CSI ?3 i

CSI ?4 i

CSI ?5 i

CSI 1 |

CSI 0 |

ESC 5

CTRL E

CTRL S

CTRL Q

Copy print mode on

Transmit form feed after send screen operation

No form feed after send screen operation

Send characters at cursor

Send answerback message

Suspend transmission

Resume transmission

More Terminal Control Commands

Display screen adjustment pattern

Sound bell, if enabled

Abort escape sequence; no character displayed^*3

Abort escape sequence; display reverse question

mark^

ESC # 8

Same

BEL (CTRL G)

CAN (CTRL X)

SUB (CTRL Z)

Initiate escape sequence

Preceding Page

ESC (CTRL []

CSI U

CSI V

Same

Terminal Resets

Soft terminal reset

Hard terminal reset

CSI ! p

ESC c

Same

Terminal Status Reports

Request primary attributes report

Request secondary attributes report

Respond with current revision

Request terminal status report

Respond terminal functioning and ready

Request cursor position report

Respond cursor at line l, column c

Request printer status report

Respond printer ready

Respond printer not ready

Respond printer not connected

Request function key status report

Respond key definitions not locked

Respond key definitions locked

CSI 0 c or ESC Z

CSI > 0 c

CSI > 1; 20; 0c

CSI 5 n

CSI 0 n

CSI 6 n

CSI l; c R

CSI ?15 n

CSI ?10 n

CSI ?11 n

CSI ?13 n

CSI ?25 n

CSI ?20 n

CSI ?21 n

Same

_{Download from Www.Somanuals.com.}3_A5_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Supported VT100, VT220 and Console ANSI Commands, Cont'd

Command

Console ANSI

FUNCTION

VT100, VT220

Request keyboard status report

Respond with keyboard language

(see table below for values of “Ps”)

CSI ? 26 n

CSI ? 27; Ps n

Same

Values of Ps (above)

Keyboard Language

U.S.

U.K.

Danish

German

French

Keyboard Language

Spanish

Swedish

Norwegian

Italian

*1. More than one mode, but less than 17, may be set with one sequence. Enter multiple numeric parameters separated

by semicolons (;). However you cannot combine sequences containing "?" with those that don't contain "?", nor can

you combine sequences ending with "h" with those ending with "l".

*2. To toggle monitor mode from the keyboard, press CTRL SHIFT 1 (use the 1 on the numeric keypad).

*3. In VT52 or VT100 modes, displays checkerboard character.

6.2 VT52 Command Guide

Table 11- VT52 Mode Escape Sequences

Command

VT52

Move cursor up one line

Move cursor down one line

Move cursor right one column

Move cursor left one column

Move cursor to home position

Move cursor up one line with scroll

Move cursor to line line, column col

Select graphics character set

Select U.S. ASCII character set

Erase from cursor to end of display

Erase from cursor to end of line

Print cursor line

ESC A

ESC B

ESC C

ESC D

ESC H

ESC I

ESC Y line col

ESC F

ESC G

ESC J

ESC K

ESC V

ESC ]

Print display

Transparent print mode on

Transparent print mode off

Copy print mode on

ESC W

ESC X

ESC ^

Copy print mode off

ESC _

ESC =

ESC >

ESC <

ESC Z

Keypad application mode on

Keypad application mode off

Enter VT100 mode

Identify terminal

_{Download from Www.Somanuals.com.}3_A6_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

7. USING PRINTER SERVER IN ETHERNET TERMINAL

Introduction

There are two ways to send the print jobs to Ethernet Terminal for printing: 1) through LPD protocol, and 2) through TFTP

protocol.

• The LPD method is more suitable for printing environments with a large number of users because the LPD

protocol has a queue process so print jobs will be kept in the print queues in the CPU.

• TFTP does not implement the print queue concept; if the printer port is not ready for accepting new print jobs, TFTP

will be terminated. Consequently, the user must send the print job again. As a result, the TFTP protocol is suitable for

printing small jobs, in an environment with a small number of users, or for testing purposes.

LPD is a built-in printing protocol in the BSD type of UNIX and is also available in most other UNIX systems. With LPD, users do

not need to install additional software to the CPU to print the jobs. Most implementations of the LPD protocol send out the data file

before the control file. However, since Ethernet Terminal must print the data file immediately upon receiving it, the print option

specified in the control file cannot take affect.

To install the printer server function of Ethernet Terminal, the first step is Basic Setup. Whichever printing protocol will be used, it

is necessary to follow "Basic Setup" first (below). If LPD will be used to print jobs, go through the "Setup for LPD" procedures

(below). If TFTP will be used, go through the "Setup for TFTP" procedures (page 37).

7.1 Basic Setup

Because the TCP/IP world uses IP addressing to communicate with each other, the purpose of Basic Setup is to assign an

IP address to the Ethernet Terminal.

For the purpose of this explanation, assume the following:

(1) Login to the UNIX CPU as root

(2) The Ethernet terminal is on the same network segment that the CPU resides.

Step 1. Add the Print Server to /etc/hosts

Create a new entry in the /etc/hosts file on all UNIX CPUs that are slated to work with Ethernet Terminal.

To create a new entry, add the following line:

IP_Address PS_NAME # comment

where: IP_Address is an IP address.

PS_NAME is a CPU name of a print server.

The statement after # is the comment for the new entry.

e.g. 90.3.2.2 ETPS1 # Ethernet Terminal

This example assigns the name ETPS1 to the Ethernet Terminal with IP address 90.3.2.2.

NOTE: The IP address is defined in the setup screen of Ethernet Terminal, as a Local IP address. Use the same one.

Step 2. Check to see if the above steps are completed

To verify if the IP address of print Server function is installed successfully, issue the following "ping" command:

ping PS_NAME [Enter]

e.g. ping ETPS1 [Enter]

7.2 Setup for LPD

Follow those steps from step 1 to step 2 described in Basic Setup. The following steps are dependent on the operating system.

Please refer to the UNIX administration guide. The following illustrated steps are under BSD system.

Step 3. Create a spooling directory

Use mkdir command to create a directory for spooling.

e.g. mkdir/usr/spool/ETPS1

_{Download from Www.Somanuals.com.}3_A7_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

Step 4. Make the directory available to LPD main process

Basically, the method has the following three procedures:

1) Assign the spooling daemon as the owner of this directory.

2) Allow the spooling daemon to be able to read from or write to the directory.

3) Enable the group of LPD main processes to be able to read from or write to the directory.

e.g. If it works on a BSD UNIX host and makes the directory /usr/ spool/ETPS1 (created in step 3) available, then follow

these three procedures:

chown daemon /usr/spool/ETPS1

chmod 775 /usr/spool/ETPS1

chgrp daemon /usr/spool/ETPS1

Step 5. Add a remote printer

To add a remote printer, insert a block similar to the following in the /etc/printcap file.

Printer_name|Remote Printer on Ethernet Terminal:\

:lp=:\

:rm=PS_NAME:\

:rp=Logic_Printer_name:\

:sd=<full path of spooler directory name>:\

e.g. If Ethernet Terminal works on a BSD UNIX host, then insert the following block into /etc/printcap file.

ETPS1|Remote Printer on Ethernet Terminal:\

:lp=:\

:rm=ETPS1:\

:rp=L1:\

:sd=/usr/spool/ETPS1:\

Step 6. Start CPU's print mechanism for BSD version UNIX system

Typing: lpc start printer_name [Enter]

e.g. lpc start ETPS1 [Enter]

Now the Ethernet Terminal is configured to accept LPD printing..

7.3 LPD printing

LPD protocol is built-in to most of the UNIX system. However, detailed implementation of LPD differs among UNIX systems.

Please refer to the UNIX administration guide for reference. The following illustrated printing command is under BSD system or

System V version.

For BSD system: lpr -P <printer_name><filename>

For System V version: lp -d <printer_name><filename>

This command is to print selected file to the selected printer.

e.g. lpr -PETPS1 /etc/hosts (BSD version) or lp -dETPS1 /etc/hosts (System V version)

This example is to print the /etc/hosts file to the Ethernet Terminal printer.

_{Download from Www.Somanuals.com.}3_A8_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

7.4 Setup for TFTP

When working on the BSD UNIX system, run the setup procedure under Setup for LPD on page 34. Otherwise run the Setup for

LPD omitting step 6.

7.5 TFTP Printing

Before using TFTP printing, the Ethernet Terminal needs to be installed completely by Setup for TFTP on page 34. TFTP Printing

lets the user send print jobs to the printers directory. There are no spooling mechanisms involved. Consequently, if that printer is

not ready, the TFTP process will be terminated immediately without sending print jobs to printers. The user must make sure the

printer is ready to print before issuing the TFTP command to have a successful result.

Log into the Ethernet Terminal with this command:

tftp <PS_NAME>

and then type:

put <file Name> Ln

where Ln is a logic printer for L1 to L8

e.g. tftp ETPS1

tftp > put /etc/hosts L1

This example prints the /etc/hosts file to the logic printer 1 of Ethernet Terminal Printer ETPS1.

_{Download from Www.Somanuals.com.}3_A9_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

8. ON-SCREEN DISPLAY (OSD)

8.1 Standard Controls

The RACKMUX LCD has 5 standard control buttons and a power LED. The 5 standard control buttons operate as follows:

•

The Power button turns the RACKMUX LCD and backlight ON and OFF as desired.

The Power LED located immediately below the Power button is a dual color

LED. It will illuminate with a green color when the RACKMUX is powered

ON and working properly. It will illuminate with a red color if the RACKMUX

is powered ON but there is no input signal detected. The LED will

Power

ON/OFF

Power LED

illuminate red only momentarily just before turning OFF.

•

The Menu button is used to bring up the OSD menu where the various

settings of the LCD display can be adjusted. Once the OSD screen is

displayed, the Menu button is used to make selections within the menus.

See "OSD Control Menu " (below) for more on LCD display settings.

Up Arrow

Controls for the

OSD Menus

Down Arrow

The Up and Down Arrow buttons are used to navigate through the

menus. Move the cursor up or down as desired to highlight an item for

selection. Once an item is highlighted, pressing the Menu button will

select it.

Select/

Auto Adjust

Figure 7- OSD Controls

•

The Select button is used to make selections within the OSD menus when

the OSD menu is ON. When the OSD menu is OFF, the Select button will

act as an Auto Adjust button to keep the user from having to use the menus

to adjust the quality of the image on the monitor.

8.2 OSD Control Menu

The OSD (On Screen Display) Menu enables the user to select the desired characteristics of the LCD display. To activate the

OSD Menu, press the Menu button (above). To turn the Menu back OFF, either select "EXIT" from the main menu or just wait

10-60 seconds and it will automatically be cleared from the screen.

8.2.1 OSD Main Menu

Selection

Brightness/Contrast

Color

Purpose

Range

1-100

Increase/decrease panel brightness/contrast level

R,G,B color temperature control

Position

•

Auto Adjust

1-100

Video Image horizontal and vertical position control

Clock setting

Phase control

Control OSD Image position on screen

Set time OSD will stay on screen before auto shutoff

Select the language of the OSD menu

Setup

Exit

10 to 60 seconds

Several languages (see page 40)

Exit from the OSD control menu

_{Download from Www.Somanuals.com.}4_A0_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

8.2.2 Brightness/Contrast Menu

Selecting the Brightness/Contrast menu will bring up a screen in which the user can adjust the brightness and contrast levels of

the LCD display. With either the BRIGHTNESS or CONTRAST sections highlighted, (use the Up or Down arrow to move

between them), press the Select button to choose the option to adjust. Then use the Up or Down Arrow to adjust the setting.

Select EXIT when finished to return to the Main Menu.

8.2.3 Color Menu

Selecting the Color menu will bring up a screen in which the user can adjust the Red, Green, and Blue color levels (values from 1-

100) of the LCD display. With the RED, GREEN, or BLUE sections highlighted, (use the Up or Down arrow to move between

them), press the Select button to choose the option to adjust. Then use the Up or Down Arrow to adjust the setting.

Select EXIT when finished to return to the Main Menu.

8.2.4 Position Menu

Selecting the Position menu will bring up a screen in which the user can select AUTO ADJUST to automatically adjust the

horizontal and vertical position of the displayed image on the monitor, as well as adjust the clock and phase settings if they are not

correct. The user can also individually adjust these settings if so desired. With any of the sections highlighted, (use the Up or

Down arrow to move between them), press the Select button to choose the option to adjust. Then use the Up or Down Arrow

to adjust the setting as needed. Select EXIT when finished to return to the Main Menu.

_{Download from Www.Somanuals.com.}4_A1_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

8.2.5 Setup Menu

Selecting the Setup menu will bring up a screen in which the user can adjust

OSD POSITION-the position of the OSD menus on the LCD display

OSD TIME-the length of time the user can be idle before the OSD menu automatically exits (adjustable from 10

to 60 seconds)

LANGUAGE-the language that the OSD menus will be presented in

With the item highlighted, (use the Up or Down arrow to move between them), press the Select button to choose the option to

adjust. Then use the Up or Down Arrow to adjust the setting as needed. Select EXIT when finished to return to the Main

Menu.

OSD Image can be moved

to different points on the

display

_{Download from Www.Somanuals.com.}4_A2_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

9. KEYBOARD FUNCTIONS

The keyboard on the RACKMUX has a standard condensed Windows format. To reduce the keyboard size, some keys have

been assigned multiple functions, accessible via the "Fn" key.

how to enable them.

This section will describe which keys have multiple functions and

9.1 Function Key Operation

The Function (“Fn”) key provides special functions on the RACKMUX keyboard, including:

ƒ enabling otherwise standard keyboard keys to be used as the keys of a numeric keypad

ƒ enabling multi-function keys to change operation

To turn ON (lock) the Function key, press the “Fn” key twice quickly (double-click). The “Fn” LED will illuminate.

To turn OFF (unlock) the Function key, press the “Fn” key twice quickly again. The “Fn” LED will turn OFF.

Note: The "Fn" key will also operate similar to the shift key (with only momentary effect). Press and hold the "Fn" key

prior to pressing the special function key. The "Fn" key will remain active as long as it is depressed.

Num Lk

Scr Lk

Insert

Prt Sc

Delete

Sys Rq

Pause

Break

F11

F12

Esc

F10

(

)

Backspace

}

]

{

[

Tab

Enter

;

CapsLock

Enter

Shift

Home

Pg Up

Pg Dn

Ctrl

Alt

End

"Fn" Key to enable additional key functions

Figure 8- US (English) Keyboard Layout

On= Function

Key feature

is ON

On= CapsLock

is locked

On= NumLock

is locked

On= Scroll Lock

is locked

Figure 9- Keyboard LED Indications

_{Download from Www.Somanuals.com.}4_A3_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

9.2 Number Pad

The functionality of a Number Pad on a standard Windows keyboard has been incorporated into this keyboard. To

substitute the keys of the Number Pad

To substitute the keys of the Number Pad:

1. Press the "NumLock" key. The NumLock LED (

2. Press the "Fn" key twice quickly (double-click). The "Fn" LED will illuminate.

) will illuminate.

To turn OFF Number Pad functions:

1. Press the "Fn" key twice quickly (double-click). The "Fn" LED will turn OFF.

2. Press the "NumLock" key. The NumLock LED (

) will turn OFF.

Note: For only momentary function of the “Fn” key, press and hold the “Fn” key (similar to the “Shift” key).

Upon release the Fn feature will be OFF.

With the “Fn” and “NumLock” LEDs illuminated, pressing some standard keys will result in displaying characters as

indicated in the chart below. (See also Fig. 10, page 44)

Table 12- Number Pad Keys

Standard Key

Displayed when NumLock is

Function when NumLock is

“ 1 ”

“ 2 ”

“ 3 ”

“ 4 ”

“ 5 ”

“ 6 ”

“ 7 ”

“ 8 ”

“ 9 ”

“ 0 ”

“ . ”

OFF

End

Down Arrow

Page Down

Left Arrow

---

Right Arrow

Home

Up Arrow

Page Up

Insert

Delete

(period)

“ / ”

(forward slash)

;

“ + ”

(semicolon)

(plus sign)

“ * ”

’

(apostrophe)

(asterisk)

(hyphen)

(minus sign)

[

ENTER

(left bracket)

NUMLCK

SCR LCK

(

{

[

Enter

;

Figure 10- Keys of the Number Pad

_{Download from Www.Somanuals.com.}4_A4_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

9.3 Other Uses of the Function Key

The Function ("Fn") key (page 43) will enable other standard keyboard features in addition to the Number Pad keys (page 44) .

Key Function when Fn key is

not locked ("Fn" LED is OFF)

Numlck (Number lock)

Insert

Key Function when Fn key is

Locked ("Fn" LED is ON)

Scr Lck (Scroll Lock)

Prt Sc (Print Screen)

Sys Rq (System Requirements)

Break

Delete

Pause

Up Arrow

Page Up

Down Arrow

Page Down

Left Arrow

Home

Right Arrow

End

Pg Up

Num Lk

Scr Lk

Insert

Prt Sc

Delete

Sys Rq

Pause

Break

Pg Dn

End

Home

Figure 11- Additional multi-function keys

Note: The "Fn" key will also operate similar to the shift key (with only momentary effect).

9.4 Numeric Keypad Option

Models with the Numeric Keypad option (-N) (i.e. RACKMUX-T15-N) have a standard Windows keyboard with 17-key numeric

keypad.

Note: The “Fn” key is not an active key on this keyboard.

Scroll

Lock

PrtSc

SysRq

Pause

Break

Delete

Home

Esc

F11

F12

F10

(

)

Backspace

Num

Lock

}

]

{

[

Page

Tab

Home

Pg Up

Page

;

Caps Lock

Enter

Down

End

Shift

PgDn

End

Enter

Del

Ins

Insert

Ctrl

Alt

Figure 12- U.S. (English) Keyboard with numeric keypad

_{Download from Www.Somanuals.com.}4_A5_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

PrtSc

SysRq

Scroll

Lock

Pause

Break

Esc

F11

F12

Delete

Home

F10

(

)

Num

Lock

Backspace

}

]

{

[

Page

Tab

PgUp

Home

;

Enter

Page

Caps Lock

Down

Shift

End

Shift

PgDn

End

Enter

Del

Ins

Ctrl

Insert

Alt

AltGr

Figure 13- U.K. (English) keyboard with numeric keypad

Druck

S-Abf

Rollen

Pause

Untbr

Entf

F11

F12

Esc

F10

)

(

Num

Pos1

7 {

0 }

9 ]

8 [

Bild

Pos1

Bild

Tab

+ ~

Bild

;

Ende

Bild

Ende

Enter

Entf

Einfg

Strg

Alt

AltGr

Einfg

Figure 14- German keyboard with numeric keypad

10. CPU-TO-RACKMUX ETHERNET CROSSOVER CABLE

In order to make a direct connection between a CPU and the ETHERNET connector of the RACKMUX, a crossover cable must be

used. The cable is made with CAT5 cable terminated with RJ45 connectors and wired according to the chart below.

Pin assignment at

Wire Color

Pin assignment at

Standard End

Crossed End

White/Orange

Orange

White/Green

Blue

White/Blue

Green

White/Brown

Brown

Crossed

End

Standard

End

Crossover Cable

_{Download from Www.Somanuals.com.}4_A6_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

11. DC POWER OPTION

If the RACKMUX has been ordered with the DC Power option (“48V” at the end of the model number), a 3-terminal block has

been provided for connection to a 36-72VDC 2A power source. The terminal block can be easily removed from under the

protective bracket to make connections. Proper connections are indicated.

Note: Be sure to properly secure the terminal block to the RACKMUX after wire insertion.

An earth ground terminal has been provided for optional use.

REAR VIEW OF RACKMUX-T1548V

protective bracket

36-72VDC

Earth ground connection

Remove screws to remove

terminal block

CAUTION: RISK OF ELECTRIC SHOCK

36-72VDC PRESENT ON DC POWER INPUT

Figure 15- RACKMUX with DC Power option

Phillips

screwdriver

Remove screws

to remove

terminal block

Power supply

ground

Figure 16- Apply wires to terminal block

_{Download from Www.Somanuals.com.}4_A7_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

DIMENSIONAL DRAWINGS

Overhead View of RACKMUX-T15

15" LCD Display

21 .9 IN .

Keyboard

Wristpad

Lock

IEC CONNECTOR

VGA

(OUT)

SERIAL 2 PARALLEL

SERIAL 1

10BaseT

MONITOR

(IN)

Rear View of RACKMUX-T15

19 .0 0 IN .

CONNECT PORTS WITH

VEXT-1,5-MM (SUPPLIED)

1.75 IN .

Front View of RACKMUX-T15

Slotted holes for securing terminal drawer to rack

Side View of RACKMUX-T15

_{Download from Www.Somanuals.com.}4_A8_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

FREQUENTLY ASKED QUESTIONS

Questions and Answers

Q. What servers can the monitor be used with?

A. All Sun and headless servers to date include at least one serial RS232 port that is used as a console port when

no directly connected keyboard is present. The Ethernet console connection should only be used with servers that

include an Ethernet RSC (Remote System Control) port. Both RS232 serial and Ethernet telnet connections

cannot be active at the same time.

Q. How do I connect the terminal to a single server using a RS232 serial connection?

A. An RS232 cable is required for connection to a server with either a male DB25 or DB9 serial port. When

connecting to a Sun server with a RJ45 console port, use the RJ45 cable and RJ45 to DB25 adapter which are

included with the server. If the RJ45 to DB25M adapter and RJ45 cable are not available, contact NTI to order

DB25M-RJ45F-T (adapter) and a Cat5 Patch cable (RJ45) of the desired length.

Q. How do I connect the terminal to multiple servers using a RS232 serial connection?

A. A Console Server must be used to connect the terminal to multiple servers. Ensure that the appropriate cables

are ordered for connection to the Sun servers in addition to a terminal cable terminating in a female DB9 (or

male DB25 when used in conjunction with the included adapter) connection. To connect to a server, the operator

will first connect to the Console Server, and then use Console Server functionality to connect to the server.

Q. What is the format of the server serial connection on the terminal?

A. The pin out adheres to a standard female 9 pin [PC] connector.

Q. How do I connect the terminal to a single server using an Ethernet telnet connection?

A. When connecting to a Sun server with an Ethernet RSC console port, a crossover or cascade Ethernet cable

may be used. Alternatively, an Ethernet switch and standard RJ45 cat 5 Ethernet cables may be used. When

using an Ethernet switch, it is advisable that this network remains private for security reasons.

Q. How do I connect the terminal to multiple servers using an Ethernet telnet connection?

A. An Ethernet switch must be used to connect the terminal to multiple servers. Standard RJ45 Cat 5 Ethernet

cables should be used to connect the switch to the terminal and servers. In use, the operator can switch the

terminal connection between [up to] 12 servers by using the hot key sequence ALT-F1 through to ALT-F12. The

state of each server session is preserved by the terminal. It is advisable that the network used to connect the

server consoles remains private for security reasons.

Q. How many servers are supported by the Ethernet telnet connection?

A. The terminal allows up to 12 Ethernet connected servers to be configured.

Q. Does the terminal require an IP address when using an Ethernet connection?

A. Yes. This is defined during terminal set up.

Q. Is any server configuration required?

A. When the terminal looses power or is powered OFF, a 'break' may be generated on the RS232 host

communications port (as is common with most general purpose terminals). To prevent this halting a Sun server,

ensure that the "alternate break" sequence is configured. See SunSolve Info Doc 21258 for details. If connecting

the terminal using the RS232 connection to a Console Server, an alternate break sequence may not be required

since some Console Servers are "Break Safe" (as is the case with all Sun UK marketed Console Servers). Refer to

the Console Server documentation for details. When using an Ethernet console connection, the alternate break

sequence need not be defined. However, the RSC Ethernet port must be configured using the "rscconfig"

command.

Q. Does the keyboard support any Sun specific keys?

A. No. Character terminals are non Sun specific, and do not require any special keys. The Break key can be used

to enter the Open Boot PROM "OK" prompt.

Q. What character resolutions does the terminal support?

A. The standard resolution is 80x24 plus a status line displayed using 800x600 pixels.

Q. What rack can I mount the unit in?

A. The rack mounted monitor has been qualified in the Sun StorEdge 72" and Sun Fire racks. Although it is not

possible to guarantee, the rack mounted monitor should be compatible with other EIA 19" racks.

Q. What is the warranty?

A. The warranty period on this product (parts and labor) is two (2) years from the date of purchase.

_{Download from Www.Somanuals.com.}4_A9_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

TECHNICAL SPECIFICATIONS

Physical

Size (In.) WxDxH

Weight

19x21.9x1.725

23.3 lbs.

Temperature

Humidity

0°~40°C operating, -20°~60°C storage

20% to 90% non-condensing

110/220VAC, 50-60Hz

36-72VDC

Power Supply (Standard)

Power Supply (RACKMUX-

T15-48V model only)

Power Consumption

Cables Included

60W (max), <25W (standby)

IEC Power cord (country specific), 1-1/2 foot 15HD VGA,6 foot DB9 female to DB25 male null

modem cable

Rack mount kit

LCD Panel Specifications

Screen size

Included for Sun & most EIA 22-36” racks

15.1” visible diagonal

Display format

Controls

Brightness

800x600

contrast, brightness, auto-adjust, color temperature

250cd/m²(Nits)

Contrast

500:1 (typical)

Viewing Angle

Keyboard Specifications

Type

140° H / 125° V

83 key (US) / 84 key (Europe)

Terminal Emulation

Emulations

VT52, VT100, VT220, Console ANSI, PC TERM, TVI910+/925, WY-50+, WY-60, WY-100, WY-

120, WY-325, PCG Alpha

Character matrix

Screen size

7x12 dot matrix in 10x16 cell with 3 dot descenders

80x25

Page length

1, 2, or 4 screens (multiple screen page length reduces maximum number of possible telnet

sessions)

Cursor

Blink or steady, block or underline

Modes

Color modes

Full duplex, half duplex, block mode, half block mode

16 foreground and 16 background colors

Communication Ports

Serial port for host

connection

One DB9M RS232 port

Network port

One RJ45 10Base-T Ethernet port

Local printer ports

Serial baud rates

Data format

Serial handshake

Communications options

One DB25F Parallel and one DB9M RS232 port

50 to 115,200 bps

7 or 8 data bits with or without parity, 1 or 2 stop bits

XON/XOFF, XPC, and hardware DTR

Single RS232 server connection, or up to 12 Ethernet telnet sessions to predefined IP addresses.

Both serial and Ethernet connections can not be used concurrently.

_{Download from Www.Somanuals.com.}5_A0_{ll Manuals Search And Download.}

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

TROUBLESHOOTING

Each and every piece of every product produced by Network Technologies Inc is 100% tested to exacting specifications. We

make every effort to insure trouble-free installation and operation of our products. If problems are experienced while installing this

product, please look over the troubleshooting chart below to see if perhaps we can answer any questions that arise. If the

answer is not found in the chart, please check the FAQs (Frequently Asked Questions) at our website at

http://www.networktechinc.com or contact us directly for help at 1-800-742-8324 (800-RGB-TECH) in US & Canada or 1-330-562-

7070 worldwide. We will be happy to assist in any way we can.

Problem/Message

"OUT OF FREQUENCY"

Cause

Solution

Input signal is outside the supported

range

Lower video frequency to be within specified range

The input signal is not present. This

message will disappear after 5 seconds. secure

The input signal is not present

immediately after power ON.

Check all cable connections- verify that they are

"POWER SAVER MODE"

"NO SIGNAL"

Check all cable connections- verify that they are

secure

"AUTO CONFIGURATION"

The LCD monitor is configuring itself for No action is necessary.

proper communication with the CPU.

Keys pressed on the keyboard

do not yield the expected result

LCD is not displaying image

“Fn” function is locked ON.

Check to see if the Fn LED is illuminated. If so, press

the “Fn” key to unlock the function.

•

Image out of range

LCD Auto-Shut OFF button is

depressed

•

Lower the resolution

Make sure nothing is resting on the button

•

LCD is powered OFF

•

Turn power to LCD ON

INDEX

ASCII commands, 18

baud rate, 10

LPD protocol, 37

Materials Supplied, 2

null modem cable, 6

Number Pad, 44

numeric keypad, 45

OSD Controls, 40

OSD Menu, 40

Configuration-default, 8

crossover cable, 6, 46

DC power supply, 47

dimensional drawings, 48

Ethernet communication, 12

Ethernet Mode, 10

FAQ, 49

OSD Setup menu, 42

print jobs, 37

Fn key, 43

printer server, 37

Rack mounting, 4

Setup mode, 7

Technical Specifications, 50

Telco mount, 5

Function key, 43

function keys, 11

gateway, 12

glass shield, 2

IP address, 12

keyboard functions, 43

Local keyboard commands, 16

LPD printing, 38

TFTP printing, 39

TFTP protocol, 37

VEXT-1.5-MM, 6

VT100,VT220, 29

WARRANTY INFORMATION

The warranty period on this product (parts and labor) is two (2) years from the date of purchase. Please contact Network

Technologies Inc at (800) 742-8324 (800-RGB-TECH) or (330) 562-7070 or visit our website at http://www.networktechinc.com

for information regarding repairs and/or returns. A return authorization number is required for all repairs/returns.

MAN029 Rev. 10/18/07

_{Download from Www.Somanuals.com.}5_A1_{ll Manuals Search And Download.}

Milwaukee Chainsaw 6215 User Manual
National Instruments Network Card NI 9802 User Manual
Nesco Food Saver Food Dehydrator User Manual
Niles Audio Stereo System IPC 6 User Manual
Norton Abrasives Saw BBC157 User Manual
Ocean Kayak Boat TORQUE User Manual
Oki Printer 5800dn User Manual
Omnimount Indoor Furnishings OM10328 User Manual
Ozaki Worldwide Portable Speaker EM686 User Manual
Panasonic Cordless Drill ey7441 User Manual