®
Netopia R2121 Dual Analog Router
User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Welcome to the Netopia R2121 User’s Reference Guide. This guide is designed to be your single
source for information about your Netopia R2121 Dual Analog Router. It is intended to be viewed
on-line, using the powerful features of the Adobe Acrobat Reader. The information display has been
deliberately designed to present the maximum information in the minimum space on your screen.
You can keep this document open while you perform any of the procedures described, and find
useful information about the procedure you are performing.
headings listed. If you are viewing this on-line, just click any link below to go to that heading.
Configuration options for your Netopia R2121 Dual Analog Router..1
1. Small Office connection to the Internet........................... 2
2. Small Office connection to the Internet........................... 3
G
Auxiliary port ................................................................ 6
Chapter 1 — Introduction.......................................................... 1-1
Overview....................................................................... 1-1
Features and capabilities ............................................... 1-1
How to use this guide .................................................... 1-2
Find a location............................................................... 2-1
What you need .............................................................. 2-1
Identify the connectors and attach the cables .................. 2-2
Netopia R2121 Dual Analog Router Back Panel Ports ....... 2-4
Netopia R2121 Dual Analog Router Status Lights ............ 2-6
Setting up your Router with the SmartStart Wizard ........... 3-3
SmartStart Wizard configuration screens ............... 3-3
Easy option.......................................................... 3-4
Advanced option .................................................. 3-8
Sharing the Connection .................................................. 3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
User’s Reference Guide
computers ........................................................... 3-9
Configuring TCP/ IP on Macintosh computers ........ 3-13
Navigating SmartView .................................................... 4-2
General Machine Information page ........................ 4-2
Connection Profiles page ...................................... 4-3
Event History pages ............................................. 4-3
Standard HTML Web-based monitoring pages ......... 4-5
Connecting to an Ethernet network.................................. 5-3
Connecting to a LocalTalk network ................................. 5-6
Wiring guidelines for PhoneNET cabling.................. 5-7
Chapter 6 — Console-based Management.................................. 6-1
Connecting through a Telnet session ............................... 6-2
Configuring Telnet software ................................... 6-3
Connecting a local terminal console cable to your router... 6-3
Navigating through the console screens .......................... 6-4
Easy Setup console screens ................................. 7-1
How to access the Easy Setup console screens ..... 7-1
Beginning Easy Setup..................................................... 7-3
Easy Setup profile ................................................ 7-3
IP Easy Setup ...................................................... 7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Easy Setup Security.............................................. 7-6
SNMP (Simple Network Management Protocol)..... 8-13
Security............................................................. 8-13
Upgrade Feature Set .......................................... 8-13
Logging ............................................................. 8-13
Installing the Syslog client .................................. 8-14
Default Answer Profile for Dial-in Connections .................. 9-4
Translation ........................................................ 10-1
Network Address Translation features ........................... 10-1
Using Network Address Translation ............................... 10-3
Associating port numbers to nodes ..................... 10-5
Using multiple Connection Profiles ....................... 10-5
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
User’s Reference Guide
IP subnets ....................................................... 10-10
Static routes .................................................... 10-12
IP address serving..................................................... 10-16
DHCP NetBIOS Options ..................................... 10-18
MacIP (Kip Forwarding) Options ......................... 10-21
NetBIOS ............................................................ 11-3
IPX Spoofing ...................................................... 11-3
IPX setup........................................................... 11-3
IPX in the answer profile ..................................... 11-5
IPX routing tables ........................................................ 11-7
Installing AppleTalk ...................................................... 12-4
Configuring AppleTalk ................................................... 12-6
EtherTalk Setup.................................................. 12-6
LocalTalk Setup ................................................. 12-7
AURP setup ....................................................... 12-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Served IP Addresses .................................................. 13-11
System Information.................................................... 13-13
SNMP ....................................................................... 13-13
The SNMP Setup screen ................................... 13-14
SNMP traps ..................................................... 13-15
G
Viewing filter sets ............................................. 14-17
Modifying filter sets .......................................... 14-18
Deleting a filter set........................................... 14-18
A sample IP filter set ........................................ 14-18
IPX filters .................................................................. 14-22
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
User’s Reference Guide
Securing network environments ......................... 14-37
Using the SecurID token card............................ 14-37
Security authentication components .................. 14-38
Configuring for security authentication ............... 14-38
Connecting using security authentication ........... 14-39
Factory defaults ........................................................... 15-7
Transferring configuration and firmware files with TFTP.... 15-7
Uploading configuration files ............................. 15-10
Transferring configuration and firmware files with
XMODEM................................................................... 15-10
Updating firmware ............................................ 15-11
Downloading configuration files ......................... 15-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part III: Appendixes
Deciding on an ISP account ............................................ B-2
Setting up a Netopia R2121 account ..................... B-2
SmartIP™............................................................ B-3
Appendix C — Understanding IP Addressing ..............................C-1
What is IP?.................................................................... C-1
About IP addressing....................................................... C-1
Subnets and subnet masks .................................. C-2
Example: Using subnets on a Class C IP internet.... C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
User’s Reference Guide
Exported services ................................................ D-5
Important notes ................................................... D-6
Software and protocols ......................................... G-3
Regulatory notices ............................................... G-3
Important safety instructions ................................ G-5
Appendix H — About 56K Line Access.......................................H-1
Glossary.................................................................................. GL-1
Download from Www.Somanuals.com. All Manuals Search And Download.
x
User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration options for your Netopia R2121 Dual Analog
Router
The Netopia R2121 can be used in different ways depending on your needs. In general, you
will probably want to use it in one or more of the following ways: (Click on one of these links)
■ “1. Small Office connection to the Internet” with several computers in your office sharing
a single IP address (Network Address Translation enabled)
■ “2. Small Office connection to the Internet” with a block of IP addresses (Network
Address Translation disabled),
■ “3. Direct Connection to a Corporate Office (Telecommuter)”
■ “4. Configured to accept incoming dial-up connections”
■ “5. Configured for two onboard and one external modem on the Auxiliary port”
This section is intended to give you a path to the appropriate installation and configuration
instructions based on your intended use for the Netopia R2121.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Small Office connection to the Internet
For Small Office connections to the Internet, using a single dynamic IP address with Network
Address Translation (NAT) enabled, you should use the following configuration option:
■ the SmartStart™ Wizard, included on your Netopia R2121 CD.
This is the fastest and simplest way to get you up and running with the minimum
difficulty.
For instructions on this option, see “Setting up your Router with the SmartStart Wizard”
on page 3-3.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Small Office connection to the Internet
For Small Office connections to the Internet, using a block of IP addresses (Network Address
Translation disabled), you should use the following configuration tool:
■ Easy Setup configuration using console-based management. This option allows maximum
flexibility for experienced users and administrators.
For instructions on this option, see “Console-based Management” on page 6-1 and
“Easy Setup” on page 7-1.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Direct Connection to a Corporate Office (Telecommuter)
For direct connections to a Corporate Office, you can use either one of two configuration
options:
■ If you will be using Network Address Translation, use the SmartStart™ Wizard, included
on your Netopia R2121 CD.
For instructions on this option, see “Setting up your Router with the SmartStart Wizard”
on page 3-3.
■ If your corporate office assigns you a static IP address, use Easy Setup under
console-based management. This option allows maximum flexibility for experienced users
and administrators.
For instructions on this option, see “Console-based Management” on page 6-1 and
“Easy Setup” on page 7-1.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Configured to accept incoming dial-up connections
To configure the Netopia R2121 to accept incoming dial-up connections, you should use the
following configuration method:
■ To create one or more dial-in Connection Profiles for each dial-in user, see “Creating a
new Connection Profile” on page 8-2.
You do this using console-based management.
For instructions on using console-based management, see “Console-based
Management” on page 6-1
For instructions on creating a Connection Profile to dial out to an ISP or corporate site,
see “Easy Setup” on page 7-1.
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Configured for two onboard and one external modem on the Auxiliary port
To configure the Netopia R2121 to use the two onboard modems and a third external modem
on the Auxiliary serial port, you should use the following configuration options. This might be
done to allow three separate simultaneous dial-in/ dial-out connections or one or two
aggregated dial-in/ dial-out calls using Multilink PPP.
■ Install the special optional modem cable available from your reseller or directly from
Netopia.
■ use the SmartStart™ Wizard, to configure your outbound connection to an ISP. For
instructions on this option, see “Setting up your Router with the SmartStart Wizard” on
page 3-3.
■ manual configuration using console-based management. You simply attach your modem
using the special modem cable, and enter the telephone number and modem init string
in your WAN configuration. For instructions on this option, see “Adding a third modem” on
page 5-5.
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction 1-1
Chapter 1
Introduction
Overview
The Netopia R2121 Dual Analog Router is a full-featured, stand-alone, multiprotocol router for connecting
diverse local area networks (LANs) to the Internet and other remote networks. The Netopia R2121 Dual Analog
Router uses two 56Kbps modems communicating over standard analog telephone lines to provide your whole
network with a high-speed connection to the outside world.
This section covers the following topics:
■
■
“Features and capabilities” on page 1-1
“How to use this guide” on page 1-2
Features and capabilities
The Netopia R2121 Dual Analog Router provides the following features:
■
■
■
WAN connection over two analog phone lines using two built-in 56Kbps modems
Support for a third (external) modem via the Auxiliary port
Support for Multilink PPP to aggregate the separate analog modems into a single virtual data pipe of
112Kbps using the built-in modems or 168Kbps by adding an external 56Kbps modem
■
■
■
Support for Ethernet LANs
Status lights (LEDs) for easy monitoring and troubleshooting
SmartStart™ Wizard software for easy configuration over an Ethernet network connection. The SmartStart
Wizard may include an optional automatic registration with one of several major ISPs, making the process
as simple as completing a registration form. Using the alternate manual setting to configure the router for
an ISP that’s not listed, the software allows you to configure your internal connection by entering just five
fields: username, password, dialup number, DNS, and IP gateway.
■
■
Support for IP and IPX routing for Internet and Intranet connectivity
IP address serving (over Ethernet or a WAN link) which allows local or remote network nodes to
automatically acquire an IP address dynamically from a designated pool of available addresses
■
■
Support for Console-based management
Support for remote configuration by your reseller, your network administrator, or technicians at Netopia,
Inc.
■
■
Wall-mountable, Bookshelf (Side-stackable), or Desktop-stackable design for efficient space usage
SmartIP™ makes it simple and economical to connect a workgroup of users to the Internet or a remote IP
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2 User’s Reference Guide
network by using Network Address Translation and a single IP address.
■
■
SmartPhone™ allows the router to share telephone lines with analog telephones or facsimile machines,
saving the cost of adding separate telephone lines for these devices. More than Plain Old Telephone
Service (POTS), SmartPhone adds distinctive ringing and CallerID capabilities.
AppleTalk support (available as a separate add-on AppleTalk kit, including a firmware feature set
enhancement and custom HD-15 dual RJ-11 PhoneNET™ connector) allows for LocalTalk to Ethernet
routing, assigning IP addresses to Macintosh users (MacIP), IP functionality for LocalTalk users, and AURP
tunneling for connectivity between remote AppleTalk networks.
■
SmartView tool allows for real-time monitoring of router status lights (LEDs), through one or more
information forms on a web-based Java applet. Internet browsers such as Netscape Navigator™ and
Microsoft’s Internet Explorer™ may be used for SmartView.
How to use this guide
This guide is designed to be your single source for information about your Netopia R2121 Dual Analog Router.
It is intended to be viewed on-line, using the powerful features of the Adobe Acrobat Reader. The information
display has been deliberately designed to present the maximum information in the minimum space on your
screen. You can keep this document open while you perform any of the procedures described, and find useful
information about the procedure you are performing.
You can also print out all of the manual, or individual sections, if you prefer to work from hard copy rather than
on-line documentation. The pages are formatted to print on standard 8 1/ 2 by 11 inch paper. We recommend
that you print on 3-hole punched paper, so that you can put the pages in a binder for future reference. For your
convenience, a printed copy is available from Netopia. Order part number TER2121/ Doc.
This guide is organized into chapters describing the Netopia R2121’s advanced features. You may want to read
each chapter’s introductory section to familiarize yourself with the various features available.
Use the guide’s table of contents and index to locate informational topics.
Download from Www.Somanuals.com. All Manuals Search And Download.
Making the Physical Connections 2-1
Chapter 2
This section tells you how to make the physical connections to your Netopia R2121 Dual Analog Router. This
■
■
■
■
“Find a location” on page 2-1
“What you need” on page 2-1
“Identify the connectors and attach the cables” on page 2-2
“Netopia R2121 Dual Analog Router Status Lights” on page 2-6
Find a location
When choosing a location for the Netopia Router, consider:
■
■
Available space and ease of installation
Physical layout of the building and how to best use the physical space available in relation to connecting
your Netopia Router to the LAN
■
■
■
■
■
Available wiring and jacks
Distance from the point of installation to the next device (length of cable or wall wiring)
Ease of access to the front of the unit for configuration and monitoring
Ease of access to the back of the unit for checking and changing cables
Cable length and network size limitations when expanding networks
For small networks, install the Netopia R2121 near one of the LANs. For large networks, you can install the
Netopia R2121 in a wiring closet or a central network administration site.
What you need
Locate all items that you need for the installation.
Included in your router package are:
■
■
■
■
■
■
The Netopia R2121 with Dual Analog
A power adapter and cord with a mini-DIN8 connector
An RJ-45 Ethernet cable
Two standard RJ-11 telephone cables
A dual DE-9 and mini-DIN8 to DE-9 console cable (for a PC or a Macintosh)
The Netopia CD containing the SmartStart Wizard, an Internet browser, Adobe® Acrobat® Reader for
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2 User’s Reference Guide
Windows and Macintosh, ZTerm terminal emulator software and NCSA Telnet 2.6 for Macintosh
You will need:
■
A Windows 95-based PC or a Macintosh with Ethernet connectivity for configuring the Netopia R2121. This
may be built-in Ethernet or an add-on card, with TCP/ IP installed and configured. See “Before running
SmartStart” on page 3-1.
■
Two telephone lines, each with its own jack, or a single jack wired for two phone lines.
Identify the connectors and attach the cables
Identify the connectors and switches on the back panel and attach the necessary Netopia Router cables.
1 Ethernet
2 Telco
3
Power
POTS Ports
8
Ethernet
1
Phone 2
Phone 1
Telco 2
Auxiliary
Power
Console
Telco 1
Normal
Uplink
1. Connect the mini-DIN8 connector from the Power Adapter to the Power port, and plug the other end into an
electrical outlet.
2. Connect one end of one of the RJ-11 cables to the “Telco 1" port, and the other end to one of your wall
outlets.
Download from Www.Somanuals.com. All Manuals Search And Download.
Making the Physical Connections 2-3
If you have two phone lines on a single wall outlet, this is the only Telco connection you need to make. The
pinout configuration for the lines on the Telco 1 port is shown in the following diagram:
1
2
3
4
5
6
7
8
Telco 1
Telco 2
Your first Telco number is carried on the inner pair and the second number on the outer pair.
3. If you have a second phone line with its own separate wall outlet, and want to use both built-in modems,
connect one end of one of the RJ-11 cables to the “Telco 2" port, and the other end to your second wall
outlet.
4. Connect the Ethernet cable to any of the Ethernet ports on the router.
(If you are connecting the router to an existing Ethernet hub, use Ethernet port #1 on the router and set the
crossover switch to the Uplink position.)
You should now have: the power adapter plugged in; the Ethernet cable connected between the router and
your computer; and the telephone cables connected between the router and the wall outlets.
5. Insert your Netopia CD and follow the instructions to install an Internet browser and the Adobe Acrobat
Reader, if you don’t already have them.
6. Now, run the SmartStart application.
SmartStart requires the following:
■
your computer must be Ethernet-capable, that is it must have both an Ethernet card and TCP/ IP stack
software. See “Before running SmartStart” on page 3-1.
■
■
your computer and the Netopia R2121 are powered ON.
the computer running SmartStart and the Netopia R2121 to be configured must be on the same Ether-
net segment; there can be no intervening routers. Repeaters, such as 10Base-T hubs, are acceptable.
Go to the section “Setting up your Router with the SmartStart Wizard” on page 3-3 for details on running
SmartStart.
Download from Www.Somanuals.com. All Manuals Search And Download.
2-4 User’s Reference Guide
Netopia R2121 Dual Analog Router Back Panel Ports
The figure below displays the back of the Netopia R2121 with Dual Analog.
Netopia R2121 with Dual Analog back panel
Telco or line ports
Ethernet
Phone 2
Phone 1
Telco 1
8
4
7
3
6
2
5
1
Auxiliary
Console
Power
Telco 2
Normal/Uplink
1
Crossover switch
Auxiliary port
Power port
8 port Ethernet hub
Console port
Download from Www.Somanuals.com. All Manuals Search And Download.
Making the Physical Connections 2-5
The following table describes all the Netopia R2121 Dual Analog Router back panel ports.
Port
Power port
Description
a mini-DIN8 power adapter cable connection.
Telco 1 port
Console port
a red RJ-11 telephone jack labelled “Telco 1".
a DE-9 Console port for a direct serial connection to the console screens. You
may use this if you are an experienced user and choose not to use SmartStart.
See “Connecting a local terminal console cable to your router” on page 6-3.
Phone 1 and 2
Auxiliary port
Telco 2 port
two yellow Phone ports above the Console port for attaching analog telephone
devices, such as phones or fax machines to share the telephone lines.
an HD-15 Auxiliary port for attaching an external modem or the optional
AppleTalk kit.
a red RJ-11 telephone jack labelled “Telco 2".
If you have only one telephone wall jack, supporting either one or two telephone
numbers, use the “Telco 1" port. “Telco 1" supports two phone connections on
a single line; “Telco 2" supports a single phone connection.
Crossover switch
a crossover switch with Normal and Uplink positions. If Ethernet Port #1 is used
for a direct Ethernet connection between a computer and the router, set the
switch to the Normal position. If you are connecting the router to an Ethernet
hub, use Ethernet port #1 on the router and set the switch to the Uplink
position.
8-port Ethernet hub
Eight Ethernet jacks. You will use one of these to configure the Netopia R2121.
For a new installation, you use the Ethernet connection. SmartStart only works
over Ethernet. Later, if you want to do some advanced configuration, you can
Telnet to the Console-based management screens via the Ethernet connection.
You may also use the Console connection to run the Console-based
management using a direct serial connection. You may either connect your
computer directly to any of the Ethernet ports on the router, or connect both
your computer and the router to an existing Ethernet hub on your LAN.
Download from Www.Somanuals.com. All Manuals Search And Download.
2-6 User’s Reference Guide
Netopia R2121 Dual Analog Router Status Lights
The figure below represents the Netopia R2121 status light (LED) panel.
Netopia R2121 LED front panel
2 3 4 5
6 7
8 9 10 11
12 13 14 15 16171819 2021
1
E t h e r n e t
L in k /R e c e iv e
Mo d e m 1
Mo d e m 2
L A N
The following table summarizes the meaning of the various LED states and colors:
When this happens...
the LEDs...
when the corresponding line is ringing
when the modem has carrier
2 and 8 flash yellow
3 and 9 are green.
when the line is busy for a non-data call
3 and 9 flash red.
Includes both directly attached and extension phones. (Red,
for when the line is not connected and if the phone
extension is off the hook; orange, for when the attached
phone is off the hook.)
when the router initiates an incoming or
outgoing call
3 and 9 flash green
when data is transmitted
when data is received
4 and 10 flash yellow.
5 and 11 flash yellow.
6 and 7 are green.
6 and 7 flash yellow.
12 flashes yellow.
when carrier is asserted
when data is transmitted or received
when data is transmitted or received by the
ethernet controller
when the Ethernet interface detects a collision 13 flashes red.
Download from Www.Somanuals.com. All Manuals Search And Download.
Making the Physical Connections 2-7
When this happens...
when link is detected
the LEDs...
14 though 21 are solid green.
when data is received on their respective ports 14 though 21 flash green
Download from Www.Somanuals.com. All Manuals Search And Download.
2-8 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your Router with the SmartStart Wizard 3-1
Chapter 3
Setting up your Router with the SmartStart Wizard
Once you’ve connected your router to your computer and your telecommunications line and installed a web
browser, you’re ready to run the Netopia SmartStart™ Wizard. The SmartStart Wizard will help you set up the
router and share the connection. The SmartStart Wizard walks you through a series of questions and based on
your responses automatically configures the router for connecting your LAN to the Internet or to your remote
corporate network.
The SmartStart Wizard will:
■
automatically check your Windows 95, 98, or NT PC’s TCP/ IP configuration to be sure you can accept a
dynamically assigned IP address, and change it for you if it is not set for dynamic addressing
■
■
■
check the physical connection from your computer to your router without your having to enter an IP address
assign an IP address to your router
allow you to register with a new ISP if you don’t already have one (for analog modem and ISDN models).
For a list of ISPs that support Netopia Routers in North America, see the Netopia website at
http:/ / www.netopia.com.
■
(for analog modem or ISDN models) allow you to enter your dial-up telephone numbers and other
information, dial up and test your connection to your chosen ISP or other remote site
Before running SmartStart
Be sure you have connected the cables and power source as described in Step 1 “Connect the Router” guide
contained in your Netopia folio.
Before you launch the SmartStart application, make sure your computer meets the following requirements:
MacOS 7.5 or later
System
software
Windows 95, 98, or NT operating system
Connectivity
software
TCP/ IP must be installed and properly
configured. See “Configuring TCP/ IP on
Windows 95, 98, or NT computers” on
page 3-9
MacTCP or Open Transport TCP/ IP must be
installed and properly configured. See
“Configuring TCP/ IP on Macintosh
computers” on page 3-13.
Connectivity
hardware
Ethernet card (10Base-T)
Either a built-in or third-party Ethernet card
(10Base-T)
Browser
software
Netscape Communicator™ or Microsoft Internet Explorer, included on the Netopia CD.
Required for web-based registration and web-based monitoring.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2 User’s Reference Guide
PC
Macintosh
Note s :
• The computer running SmartStart must be on the same Ethernet cable segment as the Netopia R2121.
Repeaters, such as 10Base-T hubs between your computer and the Netopia R2121, are acceptable, but
devices such as switches or other routers are not.
• SmartStart for the PC will set your TCP/ IP control panel to “Obtain an IP address automatically” if it is
not already set this way. This will cause your computer to reboot. If you have a specified IP address
configured in the computer, you should make a note of it before running SmartStart, in case you do not
want to use the dynamic addressing features built in to the Netopia Router and need to restore the fixed IP
address.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your Router with the SmartStart Wizard 3-3
Setting up your Router with the SmartStart Wizard
The SmartStart Wizard is tailored for your platform, but it works the same way on either a PC or a Macintosh.
Insert the Netopia CD, and in the desktop navigation screen that appears, launch the SmartStart Wizard
application.
SmartStart Wizard configuration screens
The screens described in this section are the default screens shipped on the Netopia CD. They
derive from two initialization (.ini) files included in the same directory as the SmartStart
application file. Your reseller or your ISP may have supplied you with customized versions of
these files.
■
If you have received a CD or diskette that has been customized by your reseller or ISP, you
can run the SmartStart Wizard directly from the CD or diskette and follow the instructions
your reseller or ISP provides. This makes your Netopia R2121 configuration even easier.
■
If you have received only the .ini files from your reseller or ISP, perform the following:
■
■
■
Copy the entire directory folder containing the SmartStart Wizard application from the
Netopia CD to your hard disk.
Copy the customized .ini files to the same directory folder that contains the Smart-
Start Wizard application, allowing the copy process to overwrite the original .ini files.
Run the SmartStart Wizard from your hard disk. You can then follow the instructions
your reseller or ISP provides.
The SmartStart Wizard presents a series of screens to guide you through the preliminary configuration of a
Netopia R2121. It will then create a connection profile using the information you supply to it.
Welcome screen. The first screen welcomes you to the
SmartStart Wizard configuration utility.
Click the Ne xt button after you have responded to the
interactive prompts in each screen.
The He lp button will display useful information to assist
you in responding to the interactive prompts.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-4 User’s Reference Guide
Easy or Advanced options screen. You can choose either
Eas y or Advance d setup.
■
router. This is the best choice if you are creating a
new network or don’t already have an IP addressing
scheme on your new network.
screen,” like the one shown below while SmartStart
checks the connection to your router.
■
If you choose Advance d, skip to page 3-8 now. The
SmartStart Wizard displays the “Router IP Address
screen” on page 3-8, in which you can choose ways
to modify your router’s IP address.
Easy option
Connection Test screen. SmartStart tests the
connection to the router. While it is testing the
connection, a progress indicator screen is displayed and
the router’s Ethernet LEDs flash.
When the test succeeds, SmartStart indicates success.
If the test fails, the wizard displays an error screen. If the test fails, check the following:
■
■
■
Check your cable connections. Be sure you have connected the router and the computer properly, using the
correct cables. Refer to the Step 1 “Connect the Router” sheet in your Netopia R2121 documentation folio.
Make sure the router is turned on and that there is an Ethernet connection between your computer and the
(Macintosh) is selected. If you are using a Windows PC, SmartStart will automatically detect a static IP
address and offer to configure the computer for automatic addressing. On a Macintosh computer, you must
manually set the TCP/ IP Control Panel to DHCP. See “Configuring TCP/ IP on Macintosh computers” on
page 3-13. If you currently use a static IP address outside the 192.168.1.x network, and want to continue
using it, use the Advanced option to assign the router an IP address in your target IP range. See “Advanced
option” on page 3-8.
■
If all of the above steps fail to resolve the problem, reset the router to its factory default settings and rerun
SmartStart.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your Router with the SmartStart Wizard 3-5
When the test is successful, you will see the “Manual or Automated Connection Profile screen,” shown below.
Manual or Automated Connection Profile screen. The
SmartStart Wizard asks you to select a method of
creating a connection profile. The connection profile tells
your router how to communicate with your ISP or other
remote site, such as your corporate office. You can select
either ISP Automation or Manual Entry.
Options are explained below.
Make your selection and click Ne xt.
If you select ISP Automation, SmartStart offers you the option of choosing one of several Netopia ISP
partners that support the Netopia R2121. You then see the “Internet Service Provider Selection screen” on
page 3-5.
If you select Manual Entry, you must be prepared with the following information. You must enter:
■
■
■
■
Your dial-up number, sometimes referred to as an ISP POP number
Your Login name and Password. (These are case-sensitive.)
Any PBX or Centrex phone system dialing prefix (such as “9” for an outside line)
Your PPP authentication method. Options are: PAP (Password Authentication Protocol), CHAP (Challenge
■
■
Your Domain Name Server (DNS); this entry must be an IP address in dotted decimal format. (for example,
192.168.4.10, not “joe.isp.com”)
Optionally, an alternate DNS if your ISP provided one
If you select Manual Entry, the “Connection Profile screen,” shown “Connection Profile screen” on page 3-6
appears.
Internet Service Provider Selection screen. Select an
ISP from the list of Netopia ISP partners who have
provided information for automatic setup. Choose
Ge ne ric ISP if your ISP is not included on the list. If you
don’t already have an account with the selected ISP, call
and order service using the listed customer service
telephone number.
When you have done this, click Ne xt.
■
Most ISPs will provide you with information for you to enter in the “Connection Profile screen” on page 3-6
over the phone using the toll-free phone number shown in the scrolling list. Generally, they will provide you
Download from Www.Somanuals.com. All Manuals Search And Download.
3-6 User’s Reference Guide
with:
■
■
Your Login name and Password. (These are case-sensitive.)
Note : Your ISP may provide you with additional values such as “Remote IP Gateway” or “Subnet Mask.”
These entries are not required for the SmartStart Wizard to configure your router.
If you have a PBX or Centrex phone system, you may need a dialing prefix (such as “9” for an outside line).
Connection Profile screen. Enter your ISP-supplied
configuration information mentioned above. All fields
must be filled in except the Alternate DNS field if your ISP
does not provide one. If your ISP appeared in the
your ISP will already have provided much of the
information required for the connection, and these fields
will appear grayed-out.
When you have done this, click Ne xt.
The “Name and Password screen” on page 3-6 appears;
this is where you enter the username and password for
your connection to your ISP.
Name and Password screen. Enter the username and
password that identifies you to your ISP. Your name and
password can be up to 32 characters each.
Note : Some automated profiles already specify name and
you and automatically skipped.
When you have done this, click Ne xt.
The SmartStart Wizard then posts your connection profile
information to your router.
Now the “Connection Profile Test screen,” (shown below)
appears. It allows you to test your connection to your ISP
using the connection profile you have just created.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your Router with the SmartStart Wizard 3-7
Connection Profile Test screen. SmartStart tests your
connection profile by attempting to connect to your ISP.
To test the connection profile with your ISP, click Ne xt.
While the test is running, SmartStart reports its progress
in a brief succession of dialog boxes as described below.
Available Line Test Progress screen. SmartStart tests to
see if the router can place calls on your telephone line.
While it is testing the connection, a dialog box is
displayed and the LEDs flash.
Connection Test Progress screen. SmartStart displays a
dialog box showing you that your connection profile is
being tested. If this test fails, check the physical
connections between the computer, the router, and the
wall jack or jacks. Check for errors in any manual entries
you made during the configuration process.
Final screen. When the connection tests successfully,
SmartStart displays a screen telling you that your
configuration is now complete.
In most cases, this SmartStart configuration is all that you need to get your router up and running and
connected to the Internet. However, you may want to take advantage of additional features or special
configuration options available through the console-based configuration interface. For detailed instructions, see
“Console-based Management” on page 6-1.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-8 User’s Reference Guide
Advanced option
Router IP Address screen. If you selected the Advanced
page 3-4, SmartStart asks you to choose between
entering the router’s current IP address and assigning an
IP address to the router.
If the router has already been assigned an IP address,
select the first radio button. If you do this, the “Known IP
Address screen,” appears (shown below.)
If you want to reconfigure the router with a new IP address
and subnet mask, select the second radio button. If you
do this, the “New IP Address screen” on page 3-9
appears.
When you have done this, click Ne xt.
Known IP Address screen. SmartStart displays a
recommended address for the router based on the IP
address of the computer.
recommended address.
When you have done this, click Ne xt.
SmartStart tests the connection to your router.
SmartStart then returns you to an “Connection Profile
screen” on page 3-6.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your Router with the SmartStart Wizard 3-9
New IP Address screen. If you want to change the
router’s IP address, you enter the new IP address, the
subnet mask, and the router’s serial number in this
screen. Remember, the serial number is on the bottom of
the router. It is also found in your documentation folio.
Note : Forcing a new IP address may turn off the Netopia
R2121’s IP address serving capabilities, if you assign an
IP address and subnet mask outside the router’s current
IP address serving pool. The Netopia R2121 does not
When you have done this, click Ne xt.
SmartStart forces the new IP address into the router,
tests the connection, and then resets the router.
SmartStart then returns you to the “Manual or Automated
Connection Profile screen” on page 3-5.
Sharing the Connection
Configuring TCP/IP on Windows 95, 98, or NT computers
Configuring TCP/ IP on a Windows computer requires the following:
■
■
An Ethernet card (also known as a network adapter)
The TCP/ IP protocol must be “bound” to the adapter or card
Download from Www.Somanuals.com. All Manuals Search And Download.
3-10 User’s Reference Guide
Dynamic configuration (recommended)
If you configure your Netopia R2121 using SmartStart, you can accept the dynamic IP address assigned by your
router. The Dynamic Host Configuration Protocol (DHCP) server, which enables dynamic addressing, is enabled
by default in the router. If your PC is not set for dynamic addressing, SmartStart will offer to do this for you
when you launch it. In that case, you will have to restart your PC and relaunch SmartStart. If you configure your
PC for dynamic addressing in advance, SmartStart need only be launched once. To configure your PC for
dynamic addressing do the following:
1. Go to the Start
Menu/ Settings/ Control
Panels and double click
the Ne twork icon. From
the Network components
list, select the
Configuration tab.
2. Select TCP/ IP-->Your Network Card. Then select
Prope rtie s. In the TCP/ IP Properties screen (shown
below), select the IP Addre s s tab. Click “Obtain an IP
Address automatically.”
3. Click on the DNS Configuration tab. Click Dis able DNS.
DNS will be assigned by the router with DHCP.
4. Click OK in this window, and the next window. When
prompted, reboot the computer.
Note : You can also use these instructions to configure other computers on your network to accept IP addresses
served by the Netopia R2121.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your Router with the SmartStart Wizard 3-11
Static configuration (optional)
If you are manually configuring for a fixed or static IP address, perform the following:
1. Go to Start Menu/ Settings/ Control Panels and double click the Ne twork icon. From the Network
components list, select the Configuration tab.
2. Select TCP/ IP-->Your Network Card. Then select Properties. In the TCP/ IP Properties screen (shown below),
select the IP Addre s s tab. Click “Specify an IP Address.”
Enter the following:
IP Addre s s: 192.168.1.2
Subne t Mas k: 255.255.255.0
This address is an example of one that can be used to configure the router with the Easy option in the
SmartStart Wizard. Your ISP or network administrator may ask you to use a different IP address and subnet
mask.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Click on the Gate way tab (shown below).
Under “New gateway,” enter
192.168.1.1. Click Add. This is the
Netopia R2121’s pre-assigned IP
address.
Click on the DNS Configuration tab. Click Enable DNS.
Enter the following
information:
Hos t: Type the name
you want to give to
this computer.
Domain: Type your
domain name. If you
don't have a domain
name, type your ISP's
domain name; for
example,
netopia.com.
DNS Se rve r Se arch
Orde r: Type the
primary DNS IP
address given to you
by your ISP. Click
Add. Repeat this process for the secondary DNS.
Domain Suffix Se arch Orde r: Enter the same domain
name you entered above.
4. Click OK in this window, and the next window. When prompted, reboot the computer.
Note : You can also use these instructions to configure other computers on your network with manual or static
IP addresses. Be sure each computer on your network has its own IP address.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your Router with the SmartStart Wizard 3-13
Configuring TCP/IP on Macintosh computers
The following is a quick guide to configuring TCP/ IP for MacOS computers. Configuring TCP/ IP in a Macintosh
computer requires the following:
■
You must have either Open Transport or Classic Networking (MacTCP) installed.
Note : If you want to use the Dynamic Host Configuration Protocol (DHCP) server built into your Netopia
R2121 to assign IP addresses to your Macintoshes, you must be running Open Transport, standard in
MacOS 8, and optional in earlier system versions. You can have your Netopia R2121 dynamically assign IP
addresses using MacTCP; however, to do so requires that the optional AppleTalk kit be installed which can
only be done after the router is configured.
■
You must have built-in Ethernet or a third-party Ethernet card and its associated drivers installed in your
Macintosh.
Dynamic configuration (recommended)
If you configure your Netopia R2121 using SmartStart, you can accept the dynamic IP address assigned by your
router. The Dynamic Host Configuration Protocol (DHCP), which enables dynamic addressing, is enabled by
default in the router. To configure your Macintosh computer for dynamic addressing do the following:
1. Go to the Apple menu. Select Control Pane ls and then
TCP/ IP.
2. With the TCP/ IP window open, go to the Edit menu and
select Us e r Mode . Choose Bas ic and click OK.
3. In the TCP/ IP window, select “Connect via: Ethernet” and
“Configure: Using DHCP Server.”
Note : You can also use these instructions to configure other computers on your network to accept IP addresses
served by the Netopia R2121.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-14 User’s Reference Guide
Static configuration (optional)
If you are manually configuring for a fixed or static IP address,
perform the following:
1. Go to the Apple menu. Select Control Pane ls and then
TCP/ IP or MacTCP.
2. With the TCP/ IP window open, go to the Edit menu and
select Us e r Mode . Choose Advance d and click OK.
Or, in the MacTCP window, select Ethe rne t and click the
More button.
3. In the TCP/ IP window or in the MacTCP/ More window, select or type information into the fields as shown in
the following table.
Option:
Connect via:
Select/ Type:
Ethernet
Configure:
Manually
IP Address:
192.168.1.2
255.255.255.0
192.168.1.1
Subnet mask:
Router address:
Name server address:
Enter the primary and secondary name
server addresses given to you by your ISP
Implicit Search Path:
Starting domain name:
Enter your domain name; if you do not have
a domain name, enter the domain name of
your ISP
4. Close the TCP/ IP or MacTCP control panel and save the settings.
5. If you are using MacTCP, you must restart the computer. If you are using Open Transport, you do not need
to restart. These are the only fields you need to modify in this screen.
Note : You can also use these instructions to configure other computers on your network with manual or static
IP addresses. Be sure each computer on your network has its own IP address.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your Router with the SmartStart Wizard 3-15
Dynamic configuration using MacIP (optional)
If you want to use MacIP to dynamically assign IP addresses to the Macintosh computers on your network you
must install the optional AppleTalk feature set kit.
Note: You cannot use MacIP dynamic configuration to configure your Netopia R2121 Dual Analog Router
because you must first configure the router in order to enable AppleTalk.
Once the AppleTalk kit is installed, you can configure your Macintoshes for MacIP. To configure dynamically
using MacIP, perform the following:
Using Open Transport TCP/ IP
1. Go to the Apple menu. Select Control Panels and then TCP/ IP.
2. With the TCP/ IP window open, go to the Edit menu and select User Mode. Choose Advanced and click OK.
3. In the TCP/ IP window, select or type information into the fields as shown in the following table.
TCP/ IP Option:
Connect via:
Select/ Type:
AppleTalk (MacIP)
Configure:
Using MacIP server
MacIP Server zone:
Name server address:
(select available zone)
Enter the primary and secondary name server
addresses given to you by your ISP
Implicit Search Path:
Enter your domain name; if you do not have a
Starting domain name:
domain name, enter the domain name of your ISP
4. Close the TCP/ IP control panel and save the settings.
These are the only fields you need to modify in these screens.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-16 User’s Reference Guide
Using Classic Networking (MacTCP)
1. Go to the Apple Menu. Select Control Panels and then Network.
2. In the Network window, select EtherTalk.
3. Go back to the Apple menu. Select Control Panels and then MacTCP.
4. Select EtherTalk.
From the pull-down menu under EtherTalk, select an available zone; then click the More button.
In the MacTCP/ More window select the Server radio button. If necessary, fill in the Domain Name Server
Information given to you by your administrator.
5. Restart the computer.
These are the only fields you need to modify in these screens.
Note: More information about configuring your Macintosh computer for TCP/ IP connectivity through a Netopia
R2121 can be found in Technote NIR_026, “Open Transport and Netopia Routers,” located on the Netopia Web
site.
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring with SmartView 4-1
Chapter 4
Monitoring with SmartView
This chapter discusses SmartView, the Netopia R2121’s device and network web-based monitoring tool. This
tool can provide statistical information, report on current network status, record events, and help in diagnosing
and locating problems.
This section covers the following topics:
■
■
“SmartView overview” on page 4-1
“Navigating SmartView” on page 4-2
SmartView overview
SmartView is a Java-based applet that runs in a web browser window. It intermittently polls the Router for
information to monitor the Router’s state and control connection and disconnection of Connection Profiles.
SmartView should run under any Java Virtual Machine (JVM)-enabled browser, and is therefore platform
independent.
Note: The SmartView applet will only run under Java-enabled browsers. Be sure that the browser you are using
is at least Microsoft Internet Explorer Version 3.0 or higher, or Netscape Navigator Version 3.0 or Communicator
Version 4.0 or higher. If your browser does not meet this requirement, you can upgrade with a browser supplied
on the Netopia CD.
Using SmartView, you can view your Router’s:
Connection Profile
Machine Information:
History Logs:
Device
Information:
Model
Profile Name
Firmware Version
Ethernet IP address
Date
Dial-out Profile
Dial Number
WAN
Update
Bandwidth Type
Dial Direction (In/ Out)
Remote Address
Gateway
Time
LED status
DNS
DNS Alternate
Connect/ Disconnect
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2 User’s Reference Guide
Navigating SmartView
You access the SmartView monitor by launching your web browser and entering the URL:
“http:/ / router_IP_Address/ smartview.html”
where router_IP_address is the address of your router.
Once you have invoked the SmartView pages, you should bookmark SmartView in your browser for easy access.
SmartView uses a tabbed view to categorize information and reduce the amount of information displayed at
once. You click on the tabs to display the different informational categories.
General Machine Information page
In addition to the static machine information about your router, such as model and firmware version, SmartView
displays a real-time visual representation of the Netopia R2121’s status lights (LEDs). This is particularly
useful if the router is located out of visual range, such as in a wiring closet.
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring with SmartView 4-3
Connection Profiles page
The Connection Profiles page displays the currently active Connection Profile, and any alternate profiles you
may have created. You can switch from one Connection Profile to another by disconnecting from one, and
connecting to another.
■
To hang up the current connection, and establish the one you select, click the Disconnect button for the
currently active Connection Profile.
■
■
Click the tab for the Connection Profile you want to activate.
Click the Connect Button for this Connection Profile.
Event History pages
The Netopia R2121 records certain relevant occurrences in event histories. Event histories are useful for
diagnosing problems because they list what happened before, during, and after a problem occurs. You can view
two different event histories: one for the router’s system and one for the WAN. The Netopia R2121’s built-in
battery backup prevents loss of event history from a shut down or reset.
The Router’s event histories are structured to display the most recent events first, and to make it easy to
distinguish error messages from informational messages. Error messages are prefixed with an asterisk. Both
the WAN Event History and the Device Event History retain records of up to 128 of the most recent events. You
can refresh the Event history logs by clicking the Update button.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4 User’s Reference Guide
Device Event History page
WAN Event History page
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring with SmartView 4-5
Standard HTML Web-based monitoring pages
You can also view Connection Profile information and Event Histories in the web-based monitoring pages. These
pages are provided for users without Java-enabled browsers. Unlike the SmartView pages, they are not
dynamically updated.
You access the web-based monitoring pages by launching your web browser and entering the URL:
“http:/ / router_IP_Address”
where router_IP_address is the address of your router.
■
■
■
To view your Connection Profile information, click the Connection Profiles icon.
To view Event Histories, click the Statistics icon.
To go to SmartView, if your browser is Java-enabled, click the SmartView icon.
For information on other advanced monitoring tools built into your Netopia R2121 Dual Analog Router, see
“Monitoring Tools” on page 13-1.
Download from Www.Somanuals.com. All Manuals Search And Download.
4-6 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Local Area Network 5-1
Chapter 5
This chapter describes how physically to connect the Netopia R2121 to your local area network (LAN). Before
configuration for your particular LAN requirements using Console-based Management (see “Console-based
■
■
■
■
■
“Readying computers on your local network” on page 5-1
“Connecting to an Ethernet network” on page 5-3
“Adding a third modem” on page 5-5
“Connecting to a LocalTalk network” on page 5-6
Overview
You can connect the Netopia R2121 to an IP or IPX network that uses Ethernet.
If you have purchased the AppleTalk feature expansion kit, you can also connect the Router to a LocalTalk
Additionally, you can connect a third (external) modem. See “Adding a third modem,” below.
Caution!
Before connecting the Netopia R2121 to any AppleTalk LANs that contain other AppleTalk routers, you should
read “Routers and seeding” on page 12-3.
See the sections later in this chapter for details on how to connect the Netopia R2121 to different types of
networks.
Readying computers on your local network
PC and Macintosh computers must have certain components installed before they can communicate through
the Netopia R2121. The following illustration shows the minimal requirements for a typical PC or Macintosh
computer.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2 User’s Reference Guide
Application software
TCP/ IP stack
Ethernet/ EtherTalk/ LocalTalk Driver
Your PC
or Macintosh
computer
To the Netopia R2121
newsgroups, etc. These applications may require some configuration. Examples include the Eudora e-mail
TCP/ IP stack: This is the software that lets your PC or Macintosh communicate using Internet protocols.
TCP/ IP stacks must be configured with some of the same information you used to configure the Netopia
R2121. There are a number of TCP/ IP stacks available for PC computers. Windows 95 includes a built-in
TCP/ IP stack. See “Configuring TCP/ IP on Windows 95, 98, or NT computers” on page 3-9. Macintosh
computers use either MacTCP or Open Transport. See “Configuring TCP/ IP on Macintosh computers” on
page 3-13.
Ethernet: Ethernet hardware and software drivers enable your PC or Macintosh computer to communicate on
the LAN.
EtherTalk and LocalTalk: These are AppleTalk protocols used over Ethernet.
Once the Netopia R2121 is properly configured and connected to your LAN, PC and Macintosh computers that
have their required components in place will be able to connect to the Internet or other remote IP networks.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Local Area Network 5-3
Connecting to an Ethernet network
The Netopia R2121 supports Ethernet connections through its eight Ethernet ports. The Router automatically
detects which Ethernet port is in use.
You can connect either 10Base-T or EtherWave Ethernet networks to the Netopia R2121. The following table
displays some important attributes of these types of Ethernet.
Attribute
EtherWave
10Base-T
Max. length of backbone,
branch, or end to end (cable
length)
330 feet
(100 meters)
330 feet
(100 meters)
Twisted pair
(10Base-T)
Twisted pair
(10Base-T)
Cable type
Netopia R2121 port used
Ethernet
Ethernet
Maximum 8
devices (daisy
chained)
No daisy
chain
Other restrictions
Download from Www.Somanuals.com. All Manuals Search And Download.
5-4 User’s Reference Guide
10Base-T
You can connect a standard 10Base-T Ethernet network to the Netopia R2121 using any of its available
Ethernet ports.
Netopia R2121 back panel
Ethernet
Phone 2
Phone 1
Telco 1
8
4
7
3
6
2
5
1
Auxiliary
Console
Power
Telco 2
Normal/Uplink
1
The Netopia R2121 in a 10Base-T network
Ethernet
8
4
Normal/
1
To connect your 10Base-T network to the Netopia R2121 through an Ethernet port, use a 10Base-T cable with
RJ-45 connectors.
If you have more than eight devices to connect, you can attach additional devices using either a 10Base-T hub
or an EtherWave™ daisy chain, or some combination of both.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Local Area Network 5-5
■
If you add devices connected through a hub, connect the hub to Ethernet port number 1 on the Netopia
R2121 and set the Normal/ Uplink switch to Uplink.
When there are no more free ports on the 10Base-T hub, the network can be extended using EtherWave, a daisy-chainable
Ethernet solution from Farallon.
Ethernet
8
4
Normal/
1
PC
Macintosh
PC
LaserWriter
EtherWave
ISA Card
EtherWave
NuBus Card
10BASE-T
Hub
EtherWave
Printer Adapter
EtherWave
Transceiver
Adding a third modem
You may wish to add a third (external) modem to gain additional speed for your Internet connection. You will
need to obtain the special external modem cable either from your reseller or directly from Netopia. Refer to the
sheet of optional feature set add-ons in your Netopia R2121 documentation folio.
Netopia R2121 Auxiliary port for connecting a third modem
Ethernet
Phone 2
Phone 1
Telco 1
8
4
7
3
6
2
5
1
Auxiliary
Console
Power
Telco 2
Normal/Uplink
1
Auxiliary connection port
By default, the Auxiliary port on your Netopia R2121 is enabled for an external asynchronous modem. This
means that all you have to do is connect your modem to the Auxiliary port and configure its settings in the Line
Configuration screens under the WAN Configuration menu. For detailed configuration instructions see
“Specifying telephone connections” on page 9-2.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-6 User’s Reference Guide
For pinout information on the HD-15 to DB-25 modem cable, see “Pinouts for Auxiliary Port Modem Cable,” in
Appendix G, “Technical Specifications and Safety Information.”
Connecting to a LocalTalk network
If you have purchased the AppleTalk feature expansion kit, you can also connect the Router to an AppleTalk
network that uses either Ethernet or LocalTalk. Refer to the sheet of optional feature set add-ons in your
Netopia R2121 documentation folio.
The AppleTalk feature expansion kit includes a dual RJ-11 PhoneNET® connector that attaches to the Auxiliary
port on the Netopia R2121.
Netopia R2121 Auxiliary port for connecting to LocalTalk
Ethernet
Phone 2
Phone 1
Telco 1
8
4
7
3
6
2
5
1
Auxiliary
Console
Power
Telco 2
Normal/Uplink
1
Auxiliary connection port
HD-15 (female)
Connect the male HD-15 end of the LocalTalk cable to the Auxiliary port on your Netopia R2121. Connect the
other end of the cable to your LocalTalk network. You can use only one connection on the Auxiliary port. You
cannot use both the PhoneNET connector and an external modem.
If your LocalTalk network is not based on standard PhoneNET cabling, use a PhoneNET-to-LocalTalk adaptor
cable available from Farallon division of Netopia. Connect the adaptor cable’s RJ-11 connector to the AppleTalk
cable’s PhoneNet connector. Connect the cable’s mini-DIN-3 connector to your LocalTalk network.
Be sure to observe the standard rules governing maximum cable lengths and limits on the number of nodes on
a PhoneNET network. The dual RJ-11 PhoneNET connector allows insertion in the LocalTalk daisy chain, or at
the end. If the device is connected at the end of the daisy chain, you must install the accompanying terminator.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Local Area Network 5-7
Wiring guidelines for PhoneNET cabling
22 gauge
.642 mm
24 gauge
.510 mm
26 gauge
.403 mm
Topology
daisy chain
n/ a
n/ a
1800 ft.
549 m
backbone
4500 ft.
1372 m
3000 ft.
229 m
1800 ft.
549 m
4-branch passive star*
1125 ft.
343 m
750 ft.
229 m
450 ft.
137 m
LocalTalk StarController
12-branch active star
914 m
610 m
366 m
* distance is per branch
Note: Make sure you do not connect your LocalTalk network to a Telco port or a POTS (Phone 1 and 2) port.
For detailed configuration instructions see “AppleTalk Setup” on page 12-1.
Download from Www.Somanuals.com. All Manuals Search And Download.
5-8 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Console-based Management 6-1
Chapter 6
Console-based Management
Console-based management is a menu-driven interface for the capabilities built in to the Netopia R2121.
Console-based management provides access to a wide variety of features that the router supports. You can
customize these features for your individual setup. This chapter describes how to access and navigate the
This section covers the following topics:
■
■
■
“Connecting through a Telnet session” on page 6-2
“Connecting a local terminal console cable to your router” on page 6-3
“Navigating through the console screens” on page 6-4
Console-based management screens contain seven entry points to the Netopia Router configuration and
monitoring features. The entry points are displayed in the Main Menu shown below:
Netopia R2121 v4.3
Easy Setup...
WAN Configuration...
System Configuration...
Utilities & Diagnostics...
Statistics & Logs...
Quick Menus...
Quick View...
You always start from this main screen.
■
■
The Easy Setup menus display and permit changing the values contained in the default Connection Profile
you created when you ran the SmartStart Wizard for initial configuration. Experienced users can also use
Easy Setup to initially configure the router directly through a console session without using SmartStart.
Easy Setup menus contain up to five descendant screens for viewing or altering these values. The number
of screens depends on whether you have optional features installed.
The WAN Configuration menu displays and permits changing your Connection Profile(s), creating or
deleting additional Connection Profiles, and configuring or reconfiguring the manner in which you may be
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2 User’s Reference Guide
■
■
■
■
■
■
■
■
■
■
Filter Sets (Firewalls). See “Security” on page 14-1.
SNMP (Simple Network Management Protocol). See “SNMP” on page 13-13.
Security. See “Security” on page 14-1.
Upgrade Feature Set. See “Upgrade Feature Set” on page 8-13.
Logging. See “Logging” on page 8-13.
■
The Utilities & Diagnostics menus provide a selection of seven tools for monitoring and diagnosing the
router's behavior, as well as updating the firmware and rebooting the system. See “Utilities and
Diagnostics” on page 15-1 for detailed information.
■
■
■
The Statistics & Logs menus display nine sets of tables and device logs that show information about your
router, your network and their history. See “Statistics & Logs” on page 13-4 for detailed information.
The Quick Menus screen is a shortcut entry point to twenty-two of the most commonly used configuration
menus that are accessed through the other menu entry points.
The Quick View menu displays at a glance current real-time operating information about your router. See
“Quick View status overview” on page 13-1 for detailed information.
Connecting through a Telnet session
Features of the Netopia R2121 may be configured through the console screens.
■
a network connection locally to the router or IP access to the router through the WAN port. This could be
the same connection as the one you used with SmartStart.
Note: Alternatively, you can have a direct serial console cable connection using the provided console cable
for your platform (PC or Macintosh) and the “Console” port on the back of the router. For more information
on attaching the console cable, see “Connecting a local terminal console cable to your router” on
page 6-3.
■
Telnet software installed on the computer you will use to configure the router
Download from Www.Somanuals.com. All Manuals Search And Download.
Console-based Management 6-3
Configuring Telnet software
If you are configuring your router using a Telnet session, your computer must be running a Telnet software
program.
■
■
If you connect a PC with Microsoft Windows, you can use a Windows Telnet application or simply run Telnet
from the Start menu.
If you connect a Macintosh computer, you can use the NCSA Telnet program supplied on the Netopia
R2121 CD. You install NCSA Telnet by simply dragging the application from the CD to your hard disk.
Connecting a local terminal console cable to your router
You can perform all of the System Configuration activities for your Netopia R2121 through a local serial console
connection using terminal emulation software, such as HyperTerminal provided with Windows95 on the PC, or
ZTerm, included on the Netopia CD, for the Macintosh.
The Netopia R2121 back panel has a connector labeled “Console” for attaching the Router to either a PC or
Macintosh computer via the serial port on the computer. (On a Macintosh, the serial port is called the Modem
port or the Printer port.) This connection lets you use the computer to configure and monitor the Netopia R2121
via the console screens.
Ethernet
Phone 2
Phone 1
Telco 1
8
4
7
3
6
2
5
1
Auxiliary
Console
Power
Telco 2
Normal/Uplink
1
Console connection port
DE-9 (male)
To connect the Netopia R2121 to your computer for serial console communication, use the supplied dual
console cable connector end appropriate to your platform:
■
■
■
one DE-9 connector end attaches to a PC
the mini-DIN8 connector end attaches to a Macintosh
the DE-9 end of the Console cable attaches to the Netopia R2121’s Console port
If you are configuring your router via a terminal session, your computer must be running a standard terminal
emulation or communications software program, such as those used with modems.
■
If you connect a PC with Microsoft Windows 95 or NT, you can use the HyperTerminal application bundled
with the operating system.
■
If you connect a Macintosh computer, you can use the ZTerm terminal emulation program on the supplied
Netopia R2121 CD.
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4 User’s Reference Guide
Launch your terminal emulation software and configure the communications software for the following values.
These are the default communication parameters that the Netopia R2121 uses.
Parameter
Terminal type
Suggested Value
PC: ANSI-BBS
Mac: ANSI, VT-100, or VT-200
Data bits
Parity
8
None
Stop bits
Speed
1
Options are: 9600, 19200, 38400, or 57600 bits per second
None
Flow Control
Note: The router firmware contains an autobaud detection feature. If you are at any screen on the
serial console, you can change your baud rate and press Return (HyperTerminal for the PC
requires a disconnect). The new baud rate is displayed at the bottom of the screen.
Navigating through the console screens
Use your keyboard to navigate the Netopia R2121’s configuration screens, enter and edit information, and
make choices. The following table lists the keys to use to navigate through the console screens.
To...
Use These Keys...
Move through selectable items in a screen or pop-up menu
Up, Down, Left, and
Right Arrow
To set a change to a selected item or open a pop-up menu of
options for a selected item like entering an upgrade key
Return or Enter
Change a toggle value (Yes/ No, On/ Off)
Restore an entry or toggle value to its previous value
Move one item up
Tab
Esc
Up arrow or Control + k
Move one item down
Down arrow or Control + j
Display a dump of the device event log
Display a dump of the WAN event log
Refresh the screen
Control + e
Control + f
Control + L
Go to topmost selectable item
Go to bottom right selectable item
<
>
Download from Www.Somanuals.com. All Manuals Search And Download.
Easy Setup 7-1
Chapter 7
Easy Setup
This chapter describes how to use the Easy Setup console screens on your Netopia R2121 Dual Analog Router.
The Easy Setup console screens provide an alternate method for experienced users to set up their router’s
Connection Profiles without using SmartStart. After completing the Easy Setup console screens, your router will
be ready to connect to the Internet or another remote site.
Easy Setup console screens
Using three Easy Setup console screens, you can:
■
■
■
modify a Connection Profile for your Router for the connection to your ISP or remote location;
set up IP addresses and IP address serving;
How to access the Easy Setup console screens
To access the console screens, Telnet to the Netopia Router over your Ethernet network, or you can physically
connect with a serial console cable and access the Netopia Router with a terminal emulation program. See
“Connecting through a Telnet session” on page 6-2 or “Connecting a local terminal console cable to your
router” on page 6-3.
Note: Before continuing, make sure that you have the information that your telephone service provider, ISP, or
network administrator has given you to configure the Netopia Router.
The Netopia Router’s first console screen, Main Menu, appears in the terminal emulation window of the
attached PC or Macintosh when:
■
■
■
the Netopia Router is turned on
the computer is connected to the Netopia Router
the Telnet or terminal emulation software is running and configured correctly.
Download from Www.Somanuals.com. All Manuals Search And Download.
7-2 User’s Reference Guide
A screen similar to the following appears:
Netopia R2121 v4.3
Easy Setup...
WAN Configuration...
System Configuration...
Utilities & Diagnostics...
Statistics & Logs...
Quick Menus...
Quick View...
Return/Enter goes to Easy Setup -- minimal configuration.
If you do not see the Main Menu, verify that:
■
the computer used to view the console screen has its serial port connected to the Netopia R2121’s
“Console” port or an Ethernet connection to one of its Ethernet ports. See “Connecting a local terminal
console cable to your router” on page 6-3 or “Connecting through a Telnet session” on page 6-2.
■
■
the Telnet or terminal emulation software is configured for the recommended values.
if you are connecting via the Console port, the console’s serial port is not being used by another device,
such as an internal modem, or an application. Turn off all other programs (other than your terminal
emulation program) that may be interfering with your access to the port.
■
you have entered the correct password, if necessary. Your Netopia R2121’s console access may be
password protected from a previous configuration. See your system administrator to obtain the password.
See Appendix A, “Troubleshooting,” for more suggestions.
Download from Www.Somanuals.com. All Manuals Search And Download.
Easy Setup 7-3
Beginning Easy Setup
To begin Easy Setup, select Easy Setup in the Main Menu, then press Return.
The Easy Setup Profile screen appears.
Connection Profile 1: Easy Setup Profile
Number to Dial:
12345678901234567890
Yes
Address Translation Enabled:
Local WAN IP Address:
0.0.0.0
Remote IP Address:
Remote IP Mask:
127.0.0.2
255.0.0.0
PPP Authentication...
Send User Name:
Send Password:
PAP
PREVIOUS SCREEN
NEXT SCREEN
Enter the directory number for the remote network connection.
Enter basic information about your WAN connection with this screen.
Easy Setup profile
The Easy Setup Profile screen is where you configure the parameters that control the Netopia R2121’s
connection to a specific remote destination, usually an ISP or a corporate site.
On a Netopia R2121 Dual Analog Router you can add up to 15 more connection profiles, for a total of 16. See
“Creating a new Connection Profile” on page 8-2.
1. Select Number to Dial and enter the telephone number you received from your ISP. This is the number the
Netopia R2121 dials to reach your ISP. Enter the number as you would dial it, including any required
prefixes (such as area, access, and long-distance dialing codes).
Note: When placing a multi-channel call, the answering equipment must either:
■
■
be in a “hunt group,” where a single telephone number services multiple lines, or
to use.
ISPs or corporate IS groups will meet these conditions. For other non-standard dialup connections, you
should verify that one or the other of these conditions is true.
2. To enable address translation, toggle Address Translation Enabled to Yes. For more information on
Network Address Translation, see “IP Setup, SmartIP and Network Address Translation” on page 10-1.
3. Select Local WAN IP Address and enter the local WAN address your ISP gave you.
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4 User’s Reference Guide
The default address is 0.0.0.0, which allows for dynamic addressing, when your ISP assigns an address
each time you connect. However, you may enter another address if you want to use static addressing.
■
■
When using numbered interfaces, the Netopia Router will use its local WAN IP address and subnet
mask to send packets to the remote router. Both routers have WAN IP addresses and subnet masks
associated with the connection.
When using unnumbered interfaces, the Netopia Router will use either its local Ethernet IP address or
its NAT address (if so configured) and subnet mask to send packets to the remote router. Neither
router has a WAN IP address or subnet mask associated with this connection.
Note: If your ISP has not given you their IP or subnet mask addresses, then you may enter an IP address
such as 127.0.0.2, and an IP subnet mask such as 255.0.0.0. With these settings the router will get this
information dynamically when it connects to the remote site.
4. If your ISP uses unnumbered (system-based routing), select Remote IP Address and enter the IP address
your ISP gave you.
Then select Remote IP Mask and enter the IP subnet mask of the remote site you will connect to.
5. Select the PPP Authentication pop-up menu and choose the type of connection security your ISP told you
to use (PAP, CHAP, PAP-TOKEN, or CACHE-TOKEN). If you choose any of these authentication methods, go
to the next step. If your ISP does not use any of these authentication methods, choose None and skip to
the last step. When you create a connection profile from Easy Setup, the default setting is PAP.
6. If your ISP uses PAP or PAP-TOKEN, select Send User Name and enter the user name your ISP gave you to
connect. If you selected PAP, select Send Password and enter your password. If you selected PAP-TOKEN,
you don’t enter the password now. Your name and password can be up to 32 characters each.
If your ISP uses CHAP, select Send Host Name and enter the user name your ISP gave you to connect. Then
select Send Secret and enter the secret (CHAP term for password) your ISP gave you.
If your ISP uses CACHE-TOKEN, select Send User Name and enter the user name your ISP gave you to
connect. Select Send Password and enter your password.
7. Select NEXT SCREEN and press Return. The IP Easy Setup screen appears.
IP Easy Setup
The IP Easy Setup screen is where you enter information about your Netopia Router’s:
■
■
■
■
■
IP address
Subnet mask
Default gateway IP address
Domain name server IP address
IP address serving information, such as the number of client IP addresses and the 1st client address; and
You should consult with your network administrator to obtain the information you will need. For more information
about setting up IP, see “IP Setup, SmartIP and Network Address Translation” on page 10-1.
Download from Www.Somanuals.com. All Manuals Search And Download.
Easy Setup 7-5
IP Easy Setup
Ethernet IP Address:
Ethernet Subnet Mask:
192.168.1.1
255.255.255.0
Domain Name:
Primary Domain Name Server:
0.0.0.0
0.0.0.0
Default IP Gateway:
IP Address Serving:
On
Number of Client IP Addresses:
1st Client Address:
100
192.168.1.100
PREVIOUS SCREEN
NEXT SCREEN
Enter an IP address in decimal and dot form (xxx.xxx.xxx.xxx).
Set up the basic IP & IPX attributes of your Netopia in this screen.
1. Select Ethernet IP Address and enter the first IP address from the IP address range your ISP has given
you. This will be the Netopia Router’s IP address.
If Network Address Translation is enabled in the Easy Setup connection profile, the Ethernet IP Address
defaults to an address within a range reserved by the Internet address administration authority for use
within private networks, 192.168.1.1.
Because this is a private network address, it should never be directly connected to the Internet. Using NAT
for all your connection profiles will ensure this restriction. See “IP Setup, SmartIP and Network Address
Translation” on page 10-1 of this guide for more information.
2. Select Ethernet Subnet Mask and enter the subnet mask your ISP has given you. The Ethernet Subnet
Mask defaults to a standard class C mask (for unlimited user models; smaller, for restricted user models).
3. Select Domain Name and enter the domain name your ISP has given you.
4. Select Primary Domain Name Server and enter the IP address your ISP has given you.
5. The Default IP Gateway defaults to the remote IP address you entered in the Easy Setup connection
profile. If the Netopia Router does not recognize the destination of any IP traffic, it forwards that traffic to
this gateway.
Do not confuse the remote IP address and the default gateway’s IP address with the block of local IP
addresses you receive from your ISP. You use the local IP addresses for the Netopia R2121’s Ethernet port
and for IP clients on your local network. The remote IP address and the default gateway’s IP address
should point to your ISP’s router.
6. To use DHCP and (if installed) MacIP address serving, toggle IP Address Serving to On.
Note: For information about dynamic IP address serving, see “IP Setup, SmartIP and Network Address
Translation” on page 10-1.
Download from Www.Somanuals.com. All Manuals Search And Download.
7-6 User’s Reference Guide
7. If IP Address Serving is On, select Number of Client IP Addresses. Then enter the number of available
host addresses for the Netopia R2121 Dual Analog Router to allocate to the client computers on your
network. This number defaults to the balance of the subnet addresses above the Netopia Router’s
address.
8. If IP Address Serving is On, select 1st Client Address and enter the first IP address in the set of allocated
served IP addresses.
9. Press Return. The Easy Setup Security Configuration screen appears.
Easy Setup Security
The Easy Setup Security Configuration screen lets you password-protect your Netopia R2121. Input your Write
Access Name and Write Access Password with names or numbers totaling up to eleven digits.
If you password protect the console screens, you will be prompted to enter the name and password you have
specified every time you log in to the console screens. Do not forget your name and password. If you do, you
will be unable to access any of the configuration screens.
Additional security features are available. See “Security” on page 14-1.
Easy Setup Security Configuration
It is strongly suggested that you password-protect configuration access to your
Netopia. By entering a Name and Password pair here, access via serial,
Telnet, SNMP and Web Server will be password-protected.
Be sure to remember what you have typed here, because you will be prompted for
it each time you configure this Netopia.
You can remove an existing Name and Password by clearing both fields below.
Write Access Name:
Write Access Password:
PREVIOUS SCREEN
TO MAIN MENU
RESTART DEVICE
Configure a Configuration Access Name and Password here.
configuration settings take effect.
1. Select RESTART DEVICE. A prompt asks you to confirm your choice.
2. Select CONTINUE to restart the Netopia Router and have your selections take effect.
Note: You can also restart the system at any time by using the restart utility (see “Restarting the system” on
page 15-13) or by turning the Netopia Router off and on with the power switch.
Easy Setup is now complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
WAN and System Configuration 8-1
Chapter 8
WAN and System Configuration
This chapter describes how to use the console-based management screens to access and configure advanced
features of your Netopia R2121 Dual Analog Router. You can customize these features for your individual setup.
These menus provide a powerful method for experienced users to set up their router’s connection profiles and
system configuration.
The next chapter “Managing Voice and Data Calls” on page 9-1 explains more of the Netopia R2121’s special
■
■
■
■
“Creating a new Connection Profile” on page 8-2
“System Configuration screens” on page 8-8
“Navigating through the System Configuration screens” on page 8-8
“System Configuration features” on page 8-9
Download from Www.Somanuals.com. All Manuals Search And Download.
8-2 User’s Reference Guide
Creating a new Connection Profile
Connection Profiles define the telephone and networking protocols necessary for the router to make a remote
connection. A Connection Profile is like an address book entry describing how the router is to get to a remote
site, or how to recognize and authenticate a remote user dialing in to the router. For example, to create a new
Connection Profile, you navigate to the WAN Configuration screen from the Main Menu, and select Add
Connection Profile.
WAN
Configuration
Main
Menu
Add Connection
Profile
The Add Connection Profile screen appears.
Add Connection Profile
Profile Name:
Profile Enabled:
Profile 02
Yes
IP Enabled:
IP Profile Parameters...
Yes
IPX Enabled:
No
Data Link Encapsulation is:
Data Link Options...
PPP
Telco Options...
ADD PROFILE NOW
CANCEL
Return accepts * ESC cancels * Left/Right moves insertion point * Del deletes.
Configure a new Conn. Profile. Finished? ADD or CANCEL to exit.
On a Netopia R2121 Dual Analog Router you can add up to 15 more connection profiles, for a total of 16.
1. Select Profile Name and enter a name for this connection profile. It can be any name you wish. For
example: the name of your ISP.
2. Toggle the Profile Enabled value to Yes or No. The default is Yes.
3. Select IP Profile Parameters and press Return. The IP Profile Parameters screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
WAN and System Configuration 8-3
IP Profile Parameters
Address Translation Enabled:
Yes
Local WAN IP Address:
0.0.0.0
Remote IP Address:
Remote IP Mask:
0.0.0.0
0.0.0.0
Filter Set...
Remove Filter Set
Receive RIP:
Both
Toggle to Yes if this is a single IP address ISP account.
Configure IP requirements for a remote network connection here.
4. Toggle or enter any IP Parameters you require and return to the Add Connection Profile screen by pressing
Escape. For more information, see “IP Setup, SmartIP and Network Address Translation” on page 10-1.
5. If you will be connecting with an IPX remote network, toggle IPX Enabled to Yes, and press Return.
Otherwise, accept the default No.
If you enable IPX routing, an IPX Profile Parameters menu item becomes available. Select IPX Profile
Parameters and press Return. The IPX Profile Parameters screen appears.
IPX Profile Parameters
Remote IPX Network:
Path Delay:
NetBios Packet Forwarding:
00000000
10
Off
Incoming Packet Filter Set...
Outgoing Packet Filter Set...
<<NONE>>
<<NONE>>
Incoming SAP Filter Set...
Outgoing SAP Filter Set...
<<NONE>>
<<NONE>>
Periodic RIP Timer:
Periodic SAP Timer:
60
60
Configure IPX requirements for a remote network connection here.
6. Toggle or enter any IPX Parameters you require and return to the Add Connection Profile screen by pressing
Escape. For more information, see “IPX Setup” on page 11-1.
Download from Www.Somanuals.com. All Manuals Search And Download.
8-4 User’s Reference Guide
7. Select Datalink Options and press Return. The Datalink Options screen appears.
Datalink (PPP/MP) Options
Data Compression...
Ascend LZS
PAP
Send Authentication...
Send User Name:
Send Password:
Receive User Name:
Receive Password:
Channel Usage...
Dynamic
BAP
Bandwidth Allocation...
Maximum Packet Size:
1500
In this Screen you will configure the PPP/MP specific connection params.
You can accept the defaults, or change them if you wish.
Data Compression options are: Ascend LZS (the default), Standard LZS, or None.
Send Authentication options are: PAP (Password Authentication Protocol, the default), CHAP (Challenge
Handshake Authentication Protocol), the secure token protocols PAP-TOKEN and CACHE-TOKEN, or None.
For more information about token security see “Token Security Authentication” on page 14-37. If your ISP
does not use any of these authentication methods, choose None. The Send Authentication information is
used to authenticate your call to your service provider. The Receive Username and Password information is
used to authenticate attempted dial-in connections.
■
If your ISP uses PAP or PAP-TOKEN, select Send User Name and enter the user name your ISP gave you
to connect. If you selected PAP, select Send Password and enter your password. If you selected
PAP-TOKEN, you don’t enter the password now.
■
■
If your ISP uses CHAP, select Send Host Name and enter the user name your ISP gave you to connect.
Then select Send Secret and enter the secret (CHAP term for password) your ISP gave you.
If your ISP uses CACHE-TOKEN, select Send User Name and enter the user name your ISP gave you to
connect. Select Send Password and enter your password.
You can specify user name and password for both outgoing and incoming calls. Your name and password
can be up to 32 characters each.
Download from Www.Somanuals.com. All Manuals Search And Download.
WAN and System Configuration 8-5
The Channel Usage pop-up menu allows you to choose how many lines your connections may use, and
whether or not they are preemptable. Supported options are:
Option
Behavior
Dynamic
1 to 3 channels, if available, will be used, depending on traffic volume
Only 1 channel will be used
1-Channel
2-Channels
2 channels will be preferred
2-Channel Preemptable
3-Channels
2 channels will be used, but 1 may be reallocated
3 channels will be preferred
3-Channel Preemptable
3 channels will be used, but 1 or more may be reallocated
Note: The Bandwidth Allocation pop-up options are: Off, Auto, BAP or MP+. BAP is the default. You
should only choose one of the other options if you are specifically advised to do so by your ISP or
administrator.
Return to the Add Connection Profile screen by pressing Escape.
8. Select Telco Options and press return. the Telco Options screen appears.
Telco Options
Dial...
Dial In/Out
Dialing Prefix:
Number to Dial:
Alternate Site to Dial:
Dial on Demand:
Idle Timeout (seconds):
Yes
300
CNA Validation Number:
Callback:
No
Return/Enter to allow dialing out, dialing in, or both.
In this Screen you configure options for the ways you will establish a link.
Select Dial and press Return. A pop-up menu appears. You can select the dialing options for this
Connection Profile as Dial In Only, Dial Out Only, or Dial In/ Out.
You can:
■
■
add a dialing prefix, such as “9” for an outside line on a PBX or Centrex phone system.
add the number to dial for this Connection Profile
Download from Www.Somanuals.com. All Manuals Search And Download.
8-6 User’s Reference Guide
■
■
add an alternate number to use if the first number fails to connect
change any of the default parameter settings
When you are finished with these entries, press Escape to return to the Add Connection Profile screen.
9. Select ADD PROFILE NOW and press Return. Your new Connection Profile will be added.
Viewing or editing connection profiles
If you want to view or edit the connection profiles in your router, return to the WAN Configuration screen, and
select Display/ Change Connection Profile. The list of Connection Profiles is displayed in a scrolling pop-up
screen.
WAN Configuration
+-Profile Name---------------------IP Address----IPX Network-+
+------------------------------------------------------------+
| Easy Setup Profile
127.0.0.2
0.0.0.0
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Profile 02
|
|
|
|
|
|
|
|
|
|
|
|
|
|
+------------------------------------------------------------+
Up/Down Arrow Keys to select, ESC to dismiss, Return/Enter to Edit.
Download from Www.Somanuals.com. All Manuals Search And Download.
WAN and System Configuration 8-7
Select the connection profile you want to view or edit and press Return. The profile is displayed, and you can
change any of the parameters. Changes take effect immediately without rebooting the router.
Change Connection Profile
Profile Name:
Profile Enabled:
Profile 02
Yes
IP Enabled:
IP Profile Parameters...
Yes
IPX Enabled:
No
Data Link Encapsulation is
Data Link Options...
PPP
Telco Options...
Return accepts * ESC cancels * Left/Right moves insertion point * Del deletes.
Modify Connection Profile here. Changes are immediate.
Deleting connection profiles
You can delete a connection profile by returning to the WAN Configuration menu and selecting Delete
Connection Profile.
A scrolling pop-up screen appears. Select the profile you want to delete and press Return. When prompted,
select CONTINUE, and the connection profile will be deleted.
WAN Configuration
+-Profile Name---------------------IP Address----IPX Network-+
+------------------------------------------------------------+
| Easy Setup Profile
127.0.0.2
0.0.0.0
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Profile 02
|
|
|
|
|
|
|
|
|
|
|
|
|
|
+------------------------------------------------------------+
Up/Down Arrow Keys to select, ESC to dismiss, Return/Enter to Delete.
Download from Www.Somanuals.com. All Manuals Search And Download.
8-8 User’s Reference Guide
■
■
Using Telnet with the Router’s Ethernet port IP address
Through the console port, using a local terminal (see “Connecting a local terminal console cable to your
router” on page 6-3)
You can also retrieve the Netopia R2121’s configuration information and remotely set its parameters using the
Simple Network Management Protocol (see “SNMP” on page 13-13).
Open a Telnet connection to the IP address you set in the router with SmartStart, for example “192.168.1.1.”
The console screen will open to the Main Menu, similar to the screen shown below:
Netopia R2121 v4.3
Easy Setup...
WAN Configuration...
System Configuration...
Utilities & Diagnostics...
Statistics & Logs...
Quick Menus...
Quick View...
Return/Enter goes to Easy Setup -- minimal configuration.
You always start from this main screen.
Navigating through the System Configuration screens
To help you find your way to particular screens, some sections in this guide begin with a graphical path guide
similar to the following example:
System
Configuration
Main
Menu
Network Protocols
Setup
IP Setup
This particular path guide shows how to get to the Network Protocols Setup screens. The path guide represents
these steps:
1. Beginning in the Main Menu, select the System Configuration item and press Return.
Download from Www.Somanuals.com. All Manuals Search And Download.
WAN and System Configuration 8-9
2. Select the Network Protocols item in the System Configuration screen and press Return.
3. Select the IP Setup item in the Network Protocols Setup screen and press Return.
To go back in this sequence of screens, use the Escape key.
System Configuration features
SmartStart may be all you need to configure your Netopia R2121. Some users, however, require advanced
settings or prefer manual control over the default selections that SmartStart automatically chooses. For these
users, the Netopia R2121 provides System Configuration options.
To help you determine whether you need to use the System Configuration options, review the following
requirements. If you have one or more of these needs, use the System Configuration options described in the
later chapters.
■
Two or more outgoing connection profiles to connect to more than one remote location (for example, to
connect to the Internet and to a network at another office).
■
■
■
■
■
■
System Configuration of dynamic IP address distribution through DHCP, MacIP, or BootP.
Customized incoming call profile to control received calls.
Scheduled connections.
Greater network security through the use of filters, CallerID, callback, and SecurID.
System Configuration of AppleTalk LAN settings.
System Configuration of connections to AppleTalk networks through the Internet or any IP network, using
AURP (AppleTalk “tunneling”).
■
System Configuration of connection profiles. See the table below for a partial list of the options available
through System Configuration.
Layer Category
Parameter Type
Options
Default settings
Protocol Layer
IP Parameters
Filter Sets:
Basic Firewall
NetBIOS Filter
Receive RIP:
Both
Off
Transmit RIP:
IPX Parameters
Path Delay:
1 second
No
NetBios Packet Forwarding:
Incoming/ outgoing Packet &
SAP filter:
On
Periodic RIP/ SAP timers:
60 seconds
Download from Www.Somanuals.com. All Manuals Search And Download.
8-10 User’s Reference Guide
Layer Category
Parameter Type
Options
Default settings
Datalink Layer
PPP/ MP Parameters Data Compression:
Send Authentication:
Ascend LZS
PAP
Channel Usage:
Dynamic
BAP
Bandwidth Allocation:
Maximum Packet Size:
1500
Physical Layer
Telco Parameters
Dial is set to:
Dial In/ Out
Yes
Dial On Demand is set to:
Callback is set to:
No
Idle Time-out is set for:
300 seconds
To access the System Configuration screens, select System Configuration in the Main Menu, then press
Return.
The System Configuration Menu screen appears:
System Configuration
Network Protocols Setup...
Filter Sets (Firewalls)...
IP Address Serving...
Date and Time...
Console Configuration...
SNMP (Simple Network Management Protocol)...
Security...
Upgrade Feature Set...
Logging...
Return/Enter to configure Networking Protocols (such as TCP/IP).
Use this screen if you want options beyond Easy Setup.
Download from Www.Somanuals.com. All Manuals Search And Download.
WAN and System Configuration 8-11
Network Protocols Setup
These screens allow you to configure your network’s use of the standard networking protocols:
■
■
■
IP: details are given in “IP Setup, SmartIP and Network Address Translation” on page 10-1.
IPX: details are given in “IPX Setup” on page 11-1.
AppleTalk: details are given in “AppleTalk Setup” on page 12-1.
Note: AppleTalk requires the optional AppleTalk feature expansion kit.
Filter Sets (Firewalls)
These screens allow you to configure security on your network by means of filter sets and a basic firewall.
■
IP Address Serving
These screens allow you to configure IP Address serving on your network by means of DHCP, WANIP, BootP, and
with the optional AppleTalk kit, MacIP.
■
Details are given in “IP address serving” on page 10-16.
Date and Time
You can set the system’s date and time in the Set Date and Time screen.
Select Date and Time in the System Configuration screen and press Return to go to the Set Date and Time
screen.
Set Date and Time
System Date Format:
Current Date (MM/DD/YY):
MM/DD/YY
3/16/1998
System Time Format:
Current Time:
AM or PM:
AM/PM
10:29
AM
Follow these steps to set the system’s date and time:
Download from Www.Somanuals.com. All Manuals Search And Download.
8-12 User’s Reference Guide
1. Select Current Date and enter the date in the appropriate format. Use one- or two-digit numbers for the
month and day, and the last two digits of the current year. The date’s numbers must be separated by
forward slashes (/ ).
2. Select Current Time and enter the time in the format HH:MM, where HH is the hour (using either the
12-hour or 24-hour clock) and MM is the minutes.
3. Select AM or PM and choose AM or PM.
Console Configuration
You can change the default terminal communications parameters to suit your requirements.
To go to the Console Configuration screen, select Console Configuration in the System Configuration screen.
Console Configuration
Baud Rate...
57600
Yes
Hardware Flow Control:
SET CONFIG NOW
CANCEL
Follow these steps to change a parameter’s value:
1. Select the parameter you want to change.
2. Select a new value for the parameter. Return to step 1 if you want to configure another parameter.
3. Select SET CONFIG NOW to save the new parameter settings. Select CANCEL to leave the parameters
unchanged and exit the Console Configuration screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
WAN and System Configuration 8-13
SNMP (Simple Network Management Protocol)
These screens allow you to monitor and configure your network by means of a standard Simple Network
Management Protocol (SNMP) agent.
■
Security
These screens allow you to add users and define passwords on your network.
■
Details are given in “Security” on page 14-1.
Upgrade Feature Set
You can upgrade your Netopia R2121 by adding new feature sets through the Upgrade Feature Set utility.
See the release notes that came with your router or feature set upgrade or visit the Netopia web site at
www.netopia.com for information on new feature sets, how to obtain them, and how to install them on your
Netopia R2121.
Logging
You can configure a UNIX-compatible syslog client to report a number of subsets of the events entered in the
router’s WAN Event History. See “WAN Event History” on page 13-6.The Syslog client (for the PC only) is
supplied as a .ZIP file on the Netopia CD.
Select Logging from the System Configuration menu.
The Logging Configuration screen appears.
Logging Configuration
WAN Event Log Options
Log Boot and Errors:
Log Line Specific:
Log Connections:
Log PPP, DHCP, CNA:
Log IP and IPX:
Yes
Yes
Yes
Yes
Yes
Syslog Parameters
Syslog Enabled:
Hostname or IP Address:
Facility...
No
Local 0
Return/Enter accepts * Tab toggles * ESC cancels.
Download from Www.Somanuals.com. All Manuals Search And Download.
8-14 User’s Reference Guide
By default, all events are logged in the event history.
■
■
■
■
By toggling each event descriptor either Yes or No, you can determine which ones are logged and which are
ignored.
You can enable or disable the syslog client dynamically. When enabled, it will report any appropriate and
previously unreported events.
You can specify the syslog server’s address either in dotted decimal format or as a DNS name up to 63
characters.
You can specify the UNIX syslog Facility to use by selecting the Facility pop-up.
Installing the Syslog client
The Goodies folder on the Netopia CD contains a Syslog client daemon program that can be configured to
report the WAN events you specified in the Logging Configuration screen.
To install the Syslog client daemon, exit from the graphical Netopia CD program and locate the CD directory
structure through your Windows desktop, or through Windows Explorer. Go to the Goodies directory on the CD
and locate the Sds15000.exe program. This is the Syslog daemon installer. Run the Sds15000.exe program
and follow the on screen instructions for enabling the Windows Syslog daemon.
When using syslog with a switched connection, if the host you are logging into is located on the WAN, the act of
tearing down the call generates WAN events. This requires the torn down line to come back up, effectively
making a call that will go up and down continuously. This will only occur when the router tears down the call. If
the call is cleared remotely the redial restriction takes precedence and the packets are transparently aged out
of the queue.
Download from Www.Somanuals.com. All Manuals Search And Download.
WAN and System Configuration 8-15
The following screen shows a sample syslog dump of WAN events:
Nov 5 10:14:06 tsnext.farallon.com Link 1 down: PPP PAP failure
Nov 5 10:14:06 tsnext.farallon.com >>Issued Speech Setup Request from our DN: 5108645534
Nov 5 10:14:06 tsnext.farallon.com Requested Disc. from DN: 917143652500
Nov 5 10:14:06 tsnext.farallon.com Received Clear Confirm for our DN: 5108645534
Nov 5 10:14:06 tsnext.farallon.com Link 1 down: Manual disconnect
Nov 5 10:14:06 tsnext.farallon.com >>Issued Speech Setup Request from our DN: 5108645534
Nov 5 10:14:06 tsnext.farallon.com Requested Disc. from DN: 917143652500
Nov 5 10:14:06 tsnext.farallon.com Received Clear Confirm for our DN: 5108645534
Nov 5 10:14:06 tsnext.farallon.com Link 1 down: No answer
Nov
5
10:14:06
tsnext.farallon.com
--Device
restarted-----------------------------------------
Nov 5 10:14:06 tsnext.farallon.com >>Received Speech Setup Ind. from DN: (not supplied)
Nov 5 10:14:06 tsnext.farallon.com Requested Connect to our DN: 5108645534
Nov 5 10:14:06 tsnext.farallon.com ASYNC: Modem carrier detected (more) Modem reports: 26400
V34
Nov 5 10:14:06 tsnext.farallon.com >>WAN: 56K Modem 1 activated at 115 Kbps
Nov 5 10:14:06 tsnext.farallon.com Connect Confirmed to our DN: 5108645534
Nov 5 10:14:06 tsnext.farallon.com PPP: Channel 1 up, Answer Profile name: Default Profile
Nov 5 10:14:06 tsnext.farallon.com
negotiated auth: Local PAP , Remote NONE
Nov 5 10:14:06 tsnext.farallon.com PPP: PAP we accepted remote, Channel 1 Remote name: guest
Nov 5 10:14:06 tsnext.farallon.com PPP: MP negotiated, session 1 Remote EDO: 06 03
0000C5700624 0
PPP: NCP up, session 1, Channel 1 Final (fallback)
Nov 5 10:14:06 tsnext.farallon.com PPP: CCP negotiated, session 1, type: Ascend LZS Local
mode: 1, Remote mode: 1
Nov 5 10:14:06 tsnext.farallon.com PPP: BACP negotiated, session 1 Local MN: FFFFFFFF, Remote
MN: 00000001
Nov 5 10:14:06 tsnext.farallon.com
local: 192.168.1.1
PPP: IPCP negotiated, session 1, rem: 192.168.10.100
Nov 5 10:14:06 tsnext.farallon.com >>WAN: 56K Modem 1 deactivated
Nov 5 10:14:06 tsnext.farallon.com Received Clear Ind. from DN: 5108645534, Cause: 0
Nov 5 10:14:06 tsnext.farallon.com Issued Clear Response to DN: 5108645534
Nov 5 10:14:06 tsnext.farallon.com Link 1 down: Remote clearing
Nov 5 10:14:06 tsnext.farallon.com PPP: IPCP down, session 1
Nov 5 10:14:06 tsnext.farallon.com >>Received Speech Setup Ind. from DN: (not supplied)
Download from Www.Somanuals.com. All Manuals Search And Download.
8-16 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing Voice and Data Calls 9-1
Chapter 9
Managing Voice and Data Calls
You can set a Netopia Router to make scheduled connections using designated connection profiles. This is
useful for creating and controlling regularly scheduled periods when the router can be used by hosts on your
network. It is also useful for once-only connections that you want to schedule in advance.
The Netopia R2121 Dual Analog Router can answer calls as well as initiate them. To answer calls, the Netopia
R2121 uses a Default Answer Profile. The Default Answer Profile controls how incoming calls are set up,
authenticated, filtered, and more.
This chapter also describes how to use the Netopia R2121’s SmartPhone™ feature. With SmartPhone, other
analog devices such as telephones, facsimile machines, or modems can connect to the Netopia R2121 and
communicate over the same lines. The Netopia R2121 with SmartPhone provides:
■
■
■
Caller ID support for call authentication
distinctive ring detection, primarily for party line sharing
parallel off-hook detection, preventing the Netopia R2121 from initiating calls when the telephone line is
otherwise busy
■
auxiliary telephone control, allowing management of whether a “downstream” phone can pre-empt or
■
■
■
■
“Specifying telephone connections” on page 9-2
“Default Answer Profile for Dial-in Connections” on page 9-4
“Scheduled connections” on page 9-7
“Cost control feature -- call accounting” on page 9-12
Download from Www.Somanuals.com. All Manuals Search And Download.
9-2 User’s Reference Guide
Specifying telephone connections
You can configure telephone connections in the WAN Configuration screen under the Main Menu. Select WAN
(Wide Area Network) Setup.
WAN Configuration
WAN (Wide Area Network) Setup...
Display/Change Connection Profile...
Add Connection Profile...
Delete Connection Profile...
Default Answer Profile...
Scheduled Connections...
Call Accounting Configuration...
Establish WAN Connection...
Disconnect WAN Connection...
Return/Enter for WAN line configuration.
From here you will configure yours and the remote sites' WAN information.
The Internal Modem Configuration screen appears.
Internal Modem Configuration
Modem Dialing Prefix:
PBX Dialing Prefix:
ATDT
Line 1 Directory Number:
Answer on Ring Type...
Any
Any
Line 2 Directory Number:
Answer on Ring Type...
Speaker On...
Speaker Volume...
Always
2-Medium
Aux Serial Port...
Data Rate (kbps)...
Aux Modem Init String:
Aux Modem Directory Number:
Async Modem
57.6
AT&F&C1&D2E0S0=1
Enter the dialing prefix to be sent to all modems.
Enter Information supplied to you by your telephone company.
■
You can enter a PBX or Centrex Dialing Prefix such as “9” if you are on a PBX or Centrex phone system and
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing Voice and Data Calls 9-3
require a prefix for an outside line.
■
Enter the optional telephone or Directory Numbers for the two onboard modems to provide the Netopia
R2121 with the information needed to establish a two-channel call using MP or BAP. This will advise the
remote side of an inbound data call how to connect to a second channel.
Note: When placing multi-channel calls, the answering equipment must either:
■
■
be in a “hunt group,” where a single telephone number services multiple lines, or
the answering side must implement MP or BAP as a method to advise the calling side what number(s)
to use.
ISPs or corporate IS groups will meet these conditions. For other non-standard dialup connections, you
should verify that one or the other of these conditions is true.
■
You may choose to selectively Answer inbound calls, based on a distinctive ring pattern, on each onboard
modem. This permits you to set up a party line configuration where a fax machine or other device shares
the line, but uses a different telephone number and ring pattern. Supported options are:
Ring Type:
Any
Description:
(the default) any pattern
Ring A
Ring B
Ring C
2.0 sec ON, 4.0 sec OFF (normal North American ring pattern)
0.8 sec ON, 0.4 sec OFF, 0.8 sec ON, 4.0 sec OFF
0.4 sec ON, 0.2 sec OFF, 0.4 sec ON, 0.2 sec OFF, 0.8 sec ON, 4.0 sec
OFF
Never
the line will not answer to any ring pattern
■
You may choose when the Netopia R2121’s modem connection tones are audible. Supported options are:
Selection:
Never
Behavior:
Turns off all speaker activity and hides the Speaker Volume control.
The default. Allows call placement and handshaking tones to be heard.
Same as above, but blocks dialing tones.
Until Carrier
During
Answer
Always
Allows carrier tones to be heard, as well.
■
You can specify how to use the auxiliary serial port on the Netopia R2121’s back panel. By default, this
port is enabled for an external asynchronous modem. If you have installed the optional AppleTalk feature
set, then this port defaults to a LocalTalk connection. See “AppleTalk Setup” on page 12-1 for more
Download from Www.Somanuals.com. All Manuals Search And Download.
9-4 User’s Reference Guide
information on how to use the optional AppleTalk feature set.
Netopia R2121 back panel
Ethernet
Phone 2
Phone 1
Telco 1
8
4
7
3
6
2
5
1
Auxiliary
Console
Power
Telco 2
Normal/Uplink
1
Auxiliary serial port
HD-15 (female)
For external modem applications, the Data Rate pop-up offers a variety of clock rates from 9600 to
230 Kbps. The default is 57.6 kbps.
You may also specify the Modem Init String for your modem and the Directory Number of the telephone
line connected to the third port.
Note: If you change the modem init string, you must restart the system. From the Main Menu, go to
Utilities & Diagnostics and select Restart System. The router will reboot, and your changes will be in effect.
Default Answer Profile for Dial-in Connections
The Netopia R2121 Dual Analog Router can answer calls as well as initiate them. To answer calls, the Netopia
R2121 uses a Default Answer Profile. The Default Answer Profile controls how incoming calls are set up,
authenticated, filtered, and more.
How the Default Answer Profile works
The Default Answer Profile works like a guard booth at the gate to your network: it scrutinizes incoming calls.
Like the guard booth, the Default Answer Profile allows calls based on a set of criteria that you define.
The main criterion used to check calls is whether they match one of the Connection Profiles already defined. If
PAP or CHAP authentication is being used, the default profile checks that the incoming call’s name and pass-
word/ secret match the receive name and password/ secret of a Connection Profile. If PAP or CHAP is not being
used, an incoming call is matched to a Connection Profile using the remote network’s IP address (that is, the
caller is defined as the destination of a particular connection profile).
If an incoming call is matched to an existing Connection Profile, the call is accepted. All of that Connection
Profile’s parameters, except for authentication, are adopted for the call.
You could set up the Default Answer Profile to allow calls in even if they fail to match a Connection Profile.
Continuing the guard booth analogy, this would be like removing the guards or having them wave all calls in,
regardless of their source.
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing Voice and Data Calls 9-5
If an incoming call is not required to match a connection profile, and fails to do so, it is accepted as a standard
IP connection. Accepted, unmatched calls adopt the call parameter values set in the Default Answer Profile.
To determine the call parameter values that unmatched calls will adopt, customize the Default Answer Profile
parameters in the Default Answer Profile screen.
Customizing the default profile
You can customize the Netopia Router’s default profile in the Default Answer Profile screen.
1. Select Default Answer Profile in the WAN Configuration screen. Press Return. The Default Profile screen
appears.
Default Answer Profile
Calling Number Authentication...
Preferred
Yes
Must Match a Defined Profile:
PPP Authentication...
Bandwidth Allocation...
PAP
BAP
Configure values which may be used when receiving a call in this screen.
2. To enable CNA-authentication, select Calling Number Authentication in the Default Answer Profile screen
and choose one of the following settings:
Ignored: Calling Number Authentication (CNA) is not in effect.
Preferred: This is the default setting. Authentication is attempted if the calling number is available. If
authentication fails, or the calling number is not available, the call proceeds as usual and the caller may
still connect successfully. Use this setting if you expect to receive both regular and CNA-authenticated
calls.
Required: Authentication is attempted if the calling number is available. If authentication fails, or the
calling number is not available, the Netopia Router disconnects the caller. Use this setting if you require all
calls to be CNA-authenticated.
Calling Number Authentication (CNA), is an application of CallerID. It is a method of verifying that an
incoming call is originating from an expected site. Using CNA, you can increase the security of your network
by requiring that callers not only possess the correct PPP authentication information, but also are calling
from a particular physical location.
Download from Www.Somanuals.com. All Manuals Search And Download.
9-6 User’s Reference Guide
CNA works by checking the calling number that the Netopia Router receives during the initial setup phase
of an incoming call against a set of stored numbers. Each number in the stored set is defined in a specific
connection profile. When a match occurs, the incoming call is handled by the connection profile containing
the matched number.
Using CNA can also provide cost savings because calls are not billed during the CNA phase. With CNA, a
caller can set up a connection to the Netopia Router without incurring any charges by accessing a dial-back
connection profile. If the caller’s rates are higher than those charged to the Netopia Router’s return call,
then using CNA has saved the difference.
CNA should be available where CallerID services are available. You will need to consult with your telephone
service provider to find out if your line is provisioned for CallerID.
Also note that if the calling side has instructed the phone company to block delivery of its caller ID, the
answering side will not be able to authenticate.
If your line does not support the appropriate service, CNA may not work properly.
3. To force incoming calls to match connection profiles, select Must Match a Defined Profile and toggle it to
Yes. Incoming calls that cannot be matched to a connection profile are dropped. To allow unmatched calls
to be accepted as standard IP or IPX connections, toggle Must Match a Defined Profile to No.
If Must Match a Defined Profile is set to Yes, the answer profile only accepts calls that use the same
authentication method defined in the Authentication item. If PAP or CHAP are involved, the caller must
have a name and password or secret that match one of the connection profiles. The caller must obtain
these from you or your network administrator before initiating the call.
For example, if Must Match a Defined Profile is set to Yes, and Authentication is set to PAP, then only
incoming calls that use PAP and match a connection profile will be accepted by the answer profile.
If authentication in the Default Answer Profile is set to CHAP, the value of the CHAP Challenge Name item
must be identical to the value of the Send Host Name item of the Connection Profile to be matched by the
caller.
If Must Match a Defined Profile is set to No, Authentication is assumed to be None, even if you’ve set it
to PAP or CHAP. The answer profile uses the caller’s IP address to match a connection profile. However,
the answer profile cannot discover a caller’s subnet mask; it assumes that the caller is not subnetting its
IP address:
Class A addresses are assumed to have a mask of 255.0.0.0
Class B addresses are assumed to have a mask of 255.255.0.0
Class C addresses are assumed to have a mask of 255.255.255.0. Class C address ranges are generally
the most common subnet allocated.
If a remote network has a non-standard mask (that is, it uses subnetting), the only way for it to successfully
connect to the Netopia Router is by matching a connection profile. In other words, you will have to set up a
connection profile for that network.If Must Match a Defined Profile is set to No, you can also set the
following parameters for accepted calls that do not match a connection profile:
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing Voice and Data Calls 9-7
Call acceptance scenarios
The following are a few common call acceptance scenarios and information on how to configure the Netopia
R2121 for those purposes.
■
To accept all calls, regardless of whether they match a connection profile:
Toggle Must Match a Defined Profile to No.
To only accept calls that match a connection profile through use of a name and password (or secret):
■
■
■
■
Toggle Must Match a Defined Profile to Yes, and
Set Authentication to PAP or CHAP.
Note: The authentication method you choose determines which connection profiles are accessible to
callers. For example, if you choose PAP, callers using CHAP or no authentication will be dropped by the
answer profile.
■
■
To allow calls that only match a connection profile’s remote IP and/ or IPX address:
■
■
Toggle Must Match a Defined Profile to Yes, and
set Authentication to None.
To not allow any incoming calls to connect to the Netopia Router:
■
■
Toggle Must Match a Defined Profile to Yes, and
Set the Dial option in the Telco Options screen of every connection profile to Dial Out Only
4. If you select Bandwidth Allocation, you can select a value from a pop-up window. Supported options are
Off, Auto, MP+, or BAP. The Bandwidth Allocation setting will apply to all answered calls.
Note: The Bandwidth Allocation default is BAP. You should only choose one of the other options if you are
specifically advised to do so by your ISP or administrator.
Scheduled connections
WAN
Configuration
Main
Menu
Scheduled
Connections
You can set a Netopia Router to make scheduled connections using designated connection profiles. This is
useful for creating and controlling regularly scheduled periods when the router can be used by hosts on your
network. It is also useful for once-only connections that you want to schedule in advance.
To go to the Scheduled Connections screen, select Scheduled Connections in the WAN Configuration screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
9-8 User’s Reference Guide
Scheduled Connections
Display/Change Scheduled Connection...
Add Scheduled Connection...
Delete Scheduled Connection...
Navigate from here to add/modify/change/delete Scheduled Connections.
Viewing scheduled connections
To display a table of view-only scheduled connections, select Display/ Change Scheduled Connection in the
Scheduled Connections screen. Each scheduled connection occupies one row of the table.
Scheduled Connections
+-Days----Begin At---HH:MM---When----Conn. Prof. Name----Enabled-----+
+--------------------------------------------------------------------+
| mtWtfss 08:30PM
06:00 weekly Profile 01
No
|
|
|
|
|
|
|
|
|
|
|
+--------------------------------------------------------------------+
The first column in the table shows a one-letter representation of the Days of the week, from Monday (M or m)
to Sunday (S or s). If a letter representing a day is capitalized, the connection will be activated on that day; a
lower-case letter means that the connection will not be activated on that day. If the scheduled connection is
configured for a once-only connection, the word “once” will appear instead of the days of the week.
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing Voice and Data Calls 9-9
The other columns show:
■
■
■
■
■
The time of day that the connection will Begin At
The duration of the connection (HH:MM)
Whether it’s a recurring Weekly connection or used Once Only
Which connection profile (Conn. Prof.) is used to connect
Whether the scheduled connection is currently Enabled
The router checks the date and time set in scheduled connections against the system date and time.
Adding a scheduled connection
To add a new scheduled connection, select Add Scheduled Connection in the Scheduled Connections screen
and press Return. The Add Scheduled Connection screen appears.
Add Scheduled Connection
Scheduled Connection Enable:
How Often...
On
Weekly
Forced Up
Schedule Type...
Set Weekly Schedule...
Use Connection Profile...
ADD SCHEDULED CONNECTION
CANCEL
Scheduled Connections dial remote Networks on a Weekly or Once-Only basis.
Follow these steps to configure the new scheduled connection:
■
To activate the connection, select Scheduled Connection Enable and toggle it to On. You can make the
scheduled connection inactive by toggling Scheduled Connection Enable to Off.
■
Decide how often the connection should take place by selecting How Often and choosing Weekly or Once
Download from Www.Somanuals.com. All Manuals Search And Download.
9-10 User’s Reference Guide
Only from the pop-up menu.
■
The Schedule Type item directly below How Often allows you to set the type of schedule. Options are:.
Selection:
Forced Up
Behavior:
(the default) establishes and maintains the connection for the
schedule period specified
Forced Down
tears down and prevents any connection for the schedule
period specified
Demand-Allowed
Demand-Blocked
Periodic
permits demand calls for the schedule period specified
blocks demand calls for the schedule period specified
establishes and maintains the connection for a specified
period for the duration of the scheduled connection
■
If How Often is set to Weekly, the item directly below Schedule Type reads Set Weekly Schedule. If How
Often is set to Once Only, the item directly below How Often reads Set Once-Only Schedule.
Set Weekly Schedule
If you set How Often to Weekly, select Set Weekly Schedule and go to the Set Weekly Schedule screen.
■
Select the days for the scheduled connection to occur and toggle them to Yes.
Set Weekly Schedule
Monday:
No
No
No
No
No
No
No
Tuesday:
Wednesday:
Thursday:
Friday:
Saturday:
Sunday:
Scheduled Window Start Time:
AM or PM:
11:50
AM
Scheduled Window Duration Per Day:
00:00
■
■
Select Scheduled Window Start Time and enter the time to initiate the scheduled connection.
You must enter the time in the format H:M, where H is a one- or two-digit number representing the hour and
M is a one- or two-digit number representing the minutes. The colon is mandatory. For example, the entry
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing Voice and Data Calls 9-11
1:3 (or 1:03) would be accepted as 3 minutes after one o’clock. The entry 7:0 (or 7:00) would be accepted
as seven o’clock, exactly. The entries 44, :5, and 2: would be rejected.
■
■
Select AM or PM and choose AM or PM from the pop-up menu.
Select Scheduled Window Duration Per Day and enter the maximum duration allowed for this scheduled
connection, per call.
■
If you selected Periodic as your Schedule Type in the previous screen, an additional item “Every...”
appears. Set the period of time between connections, for example every 15 minutes.
You are finished configuring the weekly options. Return to the Add Scheduled Connection screen to continue.
Set Once-Only Schedule
If you set How Often to Once Only, select Set Once-Only Schedule and go to the Set Once-Only Schedule
screen.
Set Once-Only Schedule
Place Call on (MM/DD/YY):
05/07/1998
Scheduled Window Start Time:
AM or PM:
11:50
AM
Scheduled Window Duration:
00:00
■
■
Select Place Call On (Date) and enter a date in the format MM/ DD/ YY or MM/ DD/ YYYY (month, day,
year).
Note: You must enter the date in the format specified. The slashes are mandatory. For example, the entry
5/ 7/ 98 would be accepted as May 7, 1998. The entry 5/ 7 would be rejected.
Select Scheduled Window Start Time and enter the time to initiate the scheduled connection.
Note: You must enter the time in the format H:M, where H is a one- or two-digit number representing the
hour and M is a one- or two-digit number representing the minutes. The colon is mandatory. For example,
the entry 1:3 (or 1:03) would be accepted as 3 minutes after one o’clock. The entry 7:0 (or 7:00) would be
accepted as seven o’clock, exactly. The entries 44, :5, and 2: would be rejected.
■
■
Select AM or PM and choose AM or PM.
Select Scheduled Window Duration and enter the maximum duration allowed for this scheduled
Download from Www.Somanuals.com. All Manuals Search And Download.
9-12 User’s Reference Guide
connection. Use the same format restrictions noted above.
You are finished configuring the once-only options. Return to the Add Scheduled Connection screen to continue.
■
In the Add Scheduled Connection screen, select Use Connection Profile and choose from the list of
connection profiles you have already created. A scheduled connection must be associated with a
connection profile to be useful. The connection profile becomes active during the times specified in the
associated scheduled connection, if any exists.
■
Select ADD SCHEDULED CONNECTION to save the current scheduled connection. Select CANCEL to exit
the Add Scheduled Connection screen without saving the new scheduled connection.
Modifying a scheduled connection
To modify a scheduled connection, select Change Scheduled Connection in the Scheduled Connections screen
to display a table of scheduled connections.
Select a scheduled connection from the table and go to the Change Scheduled Connection screen. The
parameters in this screen are the same as the ones in the Add Scheduled Connection screen (except that ADD
SCHEDULED CONNECTION and CANCEL do not appear). To find out how to set them, see “Adding a scheduled
connection” on page 9-9.
Deleting a scheduled connection
To delete a scheduled connection, select Delete Scheduled Connection in the Scheduled Connections screen
to display a table of scheduled connections.
Select a scheduled connection from the table and press the Return key to delete it. To exit the table without
deleting the selected scheduled connection, press the Escape key.
Cost control feature -- call accounting
The Netopia R2121 offers system-wide and per connection profile call accounting to track first minutes and
additional minutes, for initiated data and voice calls.
Main
Menu
WAN
Configuration
Call Accounting
Configuration
To go to the Call Accounting screen, select Call Accounting Configuration in the WAN Configuration screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing Voice and Data Calls 9-13
Call Accounting Configuration
Enable Call Accounting:
On
Day for auto-reset of timers:
Maximum Aggregate connect time:
12
12:00
To enable call accounting, follow these steps:
1. Select Enable Call Accounting and toggle it to On.
2. Select Day for auto-reset of timers and enter the day of the month for the Router to reset the Call Account-
ing Statistics.
3. Select Maximum Aggregate connect time (HH:MM) and enter the total amount of time to allow for out-
bound calls, where HH is the hour (using either the 12-hour or 24-hour clock) and MM is the minutes.
Download from Www.Somanuals.com. All Manuals Search And Download.
9-14 User’s Reference Guide
Once you have enabled Call Accounting, you can specify per-connection profile limits in the Telco Options for
each profile.
Go to:
Main
Menu
WAN
Configuration
Display/ Change
Connection Profile
Telco
Options
Telco Options
Dial...
Dial In/Out
Dialing Prefix:
Number to Dial:
Alternate Site to Dial:
Dial on Demand:
Idle Timeout (seconds):
Yes
300
CNA Validation Number:
Callback:
No
Maximum connect time (HH:MM):
100:00
Enter the total amount of time to allow for outbound calls.
Viewing call accounting statistics
To view call accounting statistics, go to the Statistics & Logs screen from the Main Menu and select Call
Accounting Statistics.
Main
Menu
Statistics &
Logs
Call Accounting
Statistics
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing Voice and Data Calls 9-15
The Call Accounting Statistics screen appears.
Call Accounting Statistics
Aggregate Statistics...
Profile Statistics...
If you select Aggregate Statistics, the following screen appears.
Call Accounting Aggregate Statistics
Total First Minutes:
Total Additional Time (HH:MM):
0
0:00
Remaining Time (HH:MM):
12:00
RESET AGGREGATE MINUTE COUNTERS
Trigger Date(MDY):
11/12/98
Hit Return or Enter to reset Total First/Additional Time.
■
■
■
Total First Minutes displays the total number of first minutes of outbound calls placed during the recording
interval.
Total Additional Minutes (HH:MM) displays the total remaining time of all outbound calls placed during the
recording interval.
Remaining Time (HH:MM) displays how much time is left in the recording interval. If call accounting is not
Download from Www.Somanuals.com. All Manuals Search And Download.
9-16 User’s Reference Guide
enabled, the message will read, Aggregate Not Enforced.
■
■
Trigger Date (MDY) displays the date, in month, day, year format, when the call accounting begins.
You can reset the counters by selecting RESET AGGREGATE MINUTE COUNTERS. A dialog box will ask you
to confirm the reset. Select CONTINUE to reset the counters or CANCEL to leave them as is.
If you select Profile Statistics, the following screen appears.
Call Accounting Profile Statistics (in HHHH:MM)
Profile Name---------First Minutes----Additional Minutes-------Cutoff--Expired
----------------------------------SCROLL UP-----------------------------------
Easy Setup Profile 0:00 0:00 0:00
Profile 02 0:00 0:00 0:00
---------------------------------SCROLL DOWN----------------------------------
You can view the individual usage statistics for each of the Connection Profiles you have defined.
Note: Per-profile call accounting information is accumulated even if you have not enabled call accounting in
Telco Options.
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Setup, SmartIP and Network Address Translation 10-1
Chapter 10
IP Setup, SmartIP and Network Address Translation
The Netopia R2121 uses Internet Protocol (IP) to communicate both locally and with remote networks. This
chapter shows you how to configure the Router to route IP traffic. You also learn how to configure the Router to
serve IP addresses to hosts on your local network.
Netopia’s SmartIP features IP address serving and Network Address Translation. For a detailed discussion of
Network Address Translation, see Appendix D, “Understanding Netopia NAT Behavior.” This chapter describes
Note: When you configured your Netopia R2121 using SmartStart, Network Address Translation was enabled by
default. You have the option of disabling it, if you wish. This is done through the System Configuration screens
■
■
■
■
“Network Address Translation features” on page 10-1
“Using Network Address Translation” on page 10-3
“IP setup” on page 10-6
“IP address serving” on page 10-16
Network Address Translation allows communication between the LAN connected to the Netopia R2121 and the
Internet using a single IP address, instead of a routed account with separate IP addresses for each computer
on the network.
Network Address Translation also provides increased security by hiding the local IP addresses of the LAN
connected to the Netopia R2121 from the outside world.
With SmartIP, the setup is simpler, so Internet service providers typically offer dial-up accounts supporting
Network Address Translation at a significant cost savings.
Network Address Translation features
■
NAT is selectable on a per connection basis, optionally allowing real addresses to be used for intranet
connections and proxied addresses to be used for Internet connections.
■
The NAT user can use any combination of proxied and unproxied addresses simultaneously on the available
Telco channels. For instance, one unproxied address connection profile can be used to connect to a central
office, while another proxied address connection profile can simultaneously connect the user’s Netopia
R2121 and LAN to the Internet.
■
■
The single proxy address is acquired at connection time from the answering side. The address can be
assigned by the remote router from either a dynamic pool of addresses or a fixed, static address.
Static NAT (Network Address Translation) Security is made simpler and more reliable by only having to
firewall one IP address and by obscuring the internal network structure from the Internet.
Download from Www.Somanuals.com. All Manuals Search And Download.
10-2 User’s Reference Guide
Network Address Translation works by remapping the source IP address of traffic from the LAN to a single static
or dynamically assigned IP address shown to the remote side of the router.
HOW NAT WORKS
With NAT
192.168.1.100
ISP*
192.168.1.102
192.168.1.103
163.167.132.1
192.168.1.104
192.168.1.105
192.168.1.106
Without NAT
163.167.132.1
163.167.132.2
163.167.132.1
163.167.132.3
163.167.132.2
163.167.132.3
163.167.132.4
163.167.132.5
163.167.132.4
163.167.132.6
163.167.132.5
163.167.132.6
*or corporate intranet router
The feature can be implemented on a per Connection Profile basis. The network router can use two or more
Connection Profiles simultaneously to connect to two or more networks. Each profile may have Network Address
Translation enabled.
When Network Address Translation is enabled, the Netopia R2121 can either use a statically assigned IP
address, or one dynamically assigned each time the router connects to the ISP. While a dynamically assigned IP
address offers the ISP more flexibility, it does have an important limitation. The router will require a static IP
address to support Web, FTP, or other services available to the WAN. To support these services with Network
Address Translation enabled, a service can only be associated with one machine on the LAN.
When connected to the Internet or some other large network using Network Address Translation, the individual
machines on your LAN are not directly accessible from the WAN. Network Address Translation provides an
inherently secure method of connection to the outside world.
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Setup, SmartIP and Network Address Translation 10-3
Using Network Address Translation
The following procedure describes how to use Network Address Translation.
1. Pick a network number for your local network (referred to as the internal network). This can be any IP
address range you want. The Netopia R2121 Dual Analog Router has a default IP address of 192.168.1.1.
You may choose to change this address to match a pre-existing addressing scheme. For this example, we
will use 10.0.0.0.
Note: The outside world (the external network) will not see this network number.
2. Using the internal network number, assign addresses to the local nodes on your LAN. For example, you
may assign
■
■
■
■
■
10.0.0.1 to your Netopia R2121
10.0.0.3 to an FTP server
10.0.0.4 to a Windows NT PC
10.0.0.5 to a Windows 95 PC
Note: See “Associating port numbers to nodes” on page 10-5.
3. You created a Connection Profile for your ISP when you ran the SmartStart application. In the Connection
Profile, you can toggle Address Translation Enabled to Yes or No (Yes to enable NAT) and press Return.
The Easy Setup Connection Profile is accessible either:
■
from the Easy Setup menu in the Main Menu screen, go to the Next Screen Connection Profile 1: Easy
Setup Profile
Connection Profile 1: Easy Setup Profile
Number to Dial:
12345678901234567890
Yes
Address Translation Enabled:
Local WAN IP Address:
0.0.0.0
Remote IP Address:
Remote IP Mask:
127.0.0.2
255.0.0.0
PPP Authentication...
Send User Name:
Send Password:
PAP
PREVIOUS SCREEN
NEXT SCREEN
Enter the directory number for the remote network connection.
Enter basic information about your WAN connection with this screen.
■
or, from the WAN Configuration menu in the Main Menu screen. Go to the Display/ Change Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
10-4 User’s Reference Guide
Profile screen. You access the Address Translation option from the IP Profile Parameters menu.
IP Profile Parameters
Address Translation Enabled:
Yes
Local WAN IP Address:
0.0.0.0
Remote IP Address:
Remote IP Mask:
0.0.0.0
255.0.0.0
Filter Set...
Remove Filter Set
Receive RIP:
Both
Configure IP requirements for a remote network connection here.
Select the Local WAN IP Address field. The default address is 0.0.0.0, which allows for dynamic
addressing, meaning that your ISP assigns an address each time you connect. However, if you want to use
static addressing you may enter a specific address.
4. When your Netopia R2121 connects to the ISP, the remote router assigns your Netopia R2121 an IP
address that external users use to communicate with your network.
The following Quick View screen shows an example where 192.163.100.6 is assigned to the calling
Netopia R2121. “NAT” indicates that the address was assigned dynamically by Network Address
Translation.
Quick View
11/16/1998 04:40:47 PM
Default IP Gateway: 0.0.0.0
Domain Name Server: 0.0.0.0
Domain Name: None Provided
CPU Load: 10% Unused Memory: 541 KB
Call Acct: Disabled
LocalTalk Address: 34448:149
----------------MAC Address--------IP Address-------IPX Address---EtherTalk
Ethernet Hub: 00-00-c5-70-03-48 192.163.1.1
34449: 150
Current WAN Connection Status
Profile Name----------State-%Use-Remote Address-----Est.-More Info--------------
ISP
P1
10% IP 92.163.4.1
Lcl NAT 192.163.100.6
LED Status
-PWR-+-----MODEM1-----+--CON--AUX--+-----MODEM2-----+--EN--+--------LEDS---------
RNG DCD TX RX LNK LNK RNG DCD TX RX DATA | '-'= Off 'G'
- - - - - - E - - - O | 'R'= Red 'Y'= Yellow
G
-
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Setup, SmartIP and Network Address Translation 10-5
Internal users can access the Internet as they always do; the external Internet, however, views all traffic from
the internal network as originating from 192.163.100.6. Similarly, all traffic your network receives is addressed
to 192.163.100.6.
Associating port numbers to nodes
When an IP client, such as a Netscape Navigator or Microsoft Internet Explorer, wants to establish a session
with an IP server, such as a Web server, the client machine must know the IP address to use and the TCP
service port where the traffic is to be directed.
For example, a Web browser will locate a Web server by using a combination of the IP address and TCP port
that the client machine has set up.
Just as an IP address specifies a particular computer on a network, ports are addresses that specify a
particular service in a computer. There are many universally agreed-upon ports assigned to various services.
For example:
■
■
■
■
Web servers typically use port number 80
All FTP servers use port number 21
Telnet uses port number 23
SNMP uses port number 161
To help direct incoming IP traffic to the appropriate server, the Netopia R2121 lets you associate these and
other port numbers to distinct IP addresses on your internal LAN using Exported Services. See “IP setup” on
page 10-6 for details.
Using multiple Connection Profiles
You can enable Network Address Translation on one connection profile, disable it on another, and use the two
profiles simultaneously. The profiles might have the following attributes:
■
A profile with Network Address Translation disabled connects to your branch or main office. Your company
network administrator has assigned you a local IP address range that is consistent with the address space
assigned to your company so that you seamlessly integrate when connected. The remote IP address and
mask for this profile define only the company’s address space, so that the only IP traffic you send over this
connection is for hosts and servers within your company.
■
A Network Address Translation profile connects to the Internet via an ISP. Even though the ISP assigns you
a dynamic address each time you connect, there will be no address space conflict, since Network Address
Translation hides the corporate address you use locally. You enter the ISP’s remote IP address as your
default IP gateway so that any IP traffic not intended for your corporate intranet will be directed to the ISP.
Network Address Translation guidelines
Observe the following guidelines when using Network Address Translation.
■
The router can export just one local IP address per TCP port, so you can have just one machine available
for a given service, such as one FTP server. However, some services, such as Web servers (www-http
servers), allow you to change the TCP port on both the server and client. With two different TCP ports
Download from Www.Somanuals.com. All Manuals Search And Download.
10-6 User’s Reference Guide
exported, you can have Web servers on two different IP hosts.
■
If you will be using multiple Connection Profiles, define the remote IP address of the most accessible
profile, such as that for your ISP, to the default IP gateway in the TCP/ IP settings on users’ workstations.
That way, IP traffic not intended specifically for any of the remote networks will be routed through this
“preferred” profile.
■
Associate your primary Domain Name Server (DNS) with whichever profile is more accessible. If you
choose for neither profile to be “dial-on-demand”, you may associate a secondary DNS with the other
profile. See “IP setup,” below, for more information on these settings.
IP setup
Network
Protocols
Setup
Main
Menu
System
Configuration
IP Setup
The IP Setup options screen is where you configure the Ethernet side of the Netopia R2121. The information
you enter here controls how the Router routes IP traffic.
Consult your network administrator or Internet Service Provider to obtain the IP setup information (such as the
Ethernet IP Address, Ethernet Subnet Mask, Default IP Gateway and DNS Server IP Address) you will need
before changing any of the settings in this screen. Changes made in this screen will take effect only after the
Netopia R2121 is reset.
To go to the IP Setup options screen, from the Main Menu select System Configuration and then select Network
Protocols Setup and then select IP Setup.
Note: If you have completed SmartStart or Easy Setup, the information you have already entered will appear in
the IP Setup options screen.
IP Setup
Ethernet IP Address:
Ethernet Subnet Mask:
192.168.1.1
255.255.255.0
Default IP Gateway:
Primary Domain Name Server:
Domain Name:
0.0.0.0
0.0.0.0
0.0.0.0
2.0.34.194
Exported Services...
Receive RIP:
Transmit RIP:
Off
Off
Static Routes...
Set up the basic IP attributes of your Netopia in this screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Setup, SmartIP and Network Address Translation 10-7
Follow these steps to configure IP Setup for your Netopia R2121:
■
■
Select Ethernet IP Address and enter the IP address for the Netopia R2121’s Ethernet port.
Select Ethernet Subnet Mask and enter the subnet mask for the Ethernet IP Address that you entered in
the last step.
■
Select Default IP Gateway and enter the IP address for a default gateway. This can be the address of any
major router accessible to the Netopia R2121.
A default gateway should be able to successfully route packets when the Netopia R2121 cannot recognize
the intended recipient’s IP address. A typical example of a default gateway is the ISP’s router.
■
■
Select DNS Server and enter the IP address for a domain name server. The domain name server matches
the alphabetic addresses favored by people (for example, robin.hood.com) to the IP addresses actually
used by IP routers (for example, 163.7.8.202).
If a secondary DNS server is available, select Secondary DNS Server and enter its IP address. The
secondary DNS server is used by the Netopia R2121 when the primary DNS server is inaccessible.
Entering a secondary DNS is useful but it is not necessary.
■
■
Select Domain Name and enter your network’s domain name (for example, netopia.com). Entering a
Domain Name is strongly recommended.
Select Exported Services. The Exported Services screen appears with three options, Show/ Change
Exports, Add Export, and Delete Export.
Exported Services
(Local Port to IP Address Remapping)
Show/Change Exports...
Add Export...
Delete Export...
Download from Www.Somanuals.com. All Manuals Search And Download.
10-8 User’s Reference Guide
■
Select Add Export. The Add Exported Service screen appears.
Add Exported Service
Service...
Local Server's IP Address:
ADD EXPORT NOW
0.0.0.0
CANCEL
■
Select Service. A pop-up menu of services and ports appears.
Add Exported Service
+-Type------Port--+
+-----------------+
Service...
| ftp
21
23
25
69
70
79
|
|
|
|
|
|
|
| telnet
| smtp
| tftp
| gopher
| finger
Local Server's IP Address:
| www-http 80
| pop2
| pop3
| snmp
109 |
110 |
161 |
| timbuktu 407 |
| pptp
| irc
| Other...
1723 |
6667 |
|
+-----------------+
ADD EXPORT NOW
CANCEL
5. Select any of the services/ ports and press Return to associate it with the address of a server on your local
area network. For example, if we select www-http 80, press Return, and type 10.0.0.2. The Netopia
R2121 will then redirect any incoming traffic destined for a Web server to address 10.0.0.2.
Some services such as Timbuktu require the export of multiple TCP ports. When you associate Timbuktu
with a local server (or Timbuktu host) all of the major Timbuktu services are exported, i.e., Observe,
Control, Send, and Exchange.
Note: If the TCP port of a service you wish to use is not listed, you can add it by selecting Other...
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Setup, SmartIP and Network Address Translation 10-9
Press the Escape key when you are finished configuring Exported Services to go back to the IP Setup
screen.
IP Setup
Ethernet IP Address:
Ethernet Subnet Mask:
192.168.6.137
255.255.255.248
Default IP Gateway:
0.0.0.0
DNS Server:
Secondary DNS Server:
Domain Name:
0.0.0.0
0.0.0.0
Receive RIP:
Transmit RIP:
Both
Off
Static Routes...
Set up the basic IP attributes of your Netopia in this screen.
Follow these steps to configure IP Setup for your Corporate Netopia R2121:
■
■
Select Ethernet IP Address and enter the IP address for the Netopia R2121’s Ethernet port.
Select Ethernet Subnet Mask and enter the subnet mask for the Ethernet IP Address that you entered in
the last step.
■
Select Default IP Gateway and enter the IP address for a default gateway. This can be the address of any
major router accessible to the Netopia R2121 such as 127.0.0.2.
A default gateway should be able to successfully route packets when the Netopia R2121 cannot recognize
the intended recipient’s IP address. A typical example of a default gateway is the a corporate dial-in or
ISP’s router.
■
■
Select DNS Server and enter the IP address for a domain name server. The domain name server matches
the alphabetic addresses favored by people (for example, www.netopia.com) to the IP addresses actually
used by IP routers (for example, 163.7.8.202).
If a secondary DNS server is available, select Secondary DNS Server and enter its IP address. The
secondary DNS server is used by the Netopia R2121 when the primary DNS server is inaccessible.
Entering a secondary DNS is useful but it is not necessary.
■
■
Select Domain Name and enter your network’s domain name (for example, netopia.com).
Routing Information Protocol (RIP) is needed if there are IP routers on other segments of your Ethernet
network that the Netopia R2121 needs to recognize. If this is the case select Receive RIP and select v1,
v2, or Both from the popup menu. With Receive RIP set to “v1,” the Netopia R2121’s Ethernet port will
accept routing information provided by RIP packets from other routers that use the same subnet mask. Set
to “v2,” the Netopia R2121 will accept routing information provided by RIP packets from other routers that
use different subnet masks. Set to “Both,” the Netopia R2121 will accept information from either RIP v1 or
Download from Www.Somanuals.com. All Manuals Search And Download.
10-10 User’s Reference Guide
v2 routers.
■
If you want the Netopia R2121 to advertise its routing table to other routers via RIP, select Transmit RIP
and select v1, v2 (broadcast), or v2 (multicast) from the popup menu. With Transmit RIP v1 selected, the
Netopia R2121 will generate RIP packets only to other RIP v1 routers. With Transmit RIP v2 (broadcast)
selected, the Netopia R2121 will generate RIP packets to all other hosts on the network. With Transmit RIP
v2 (multicast) selected, the Netopia R2121 will generate RIP packets only to other routers capable of
recognizing RIP v2 packets.
IP subnets
The IP Subnets screen allows you to configure up to eight Ethernet IP subnets, one “primary” subnet and up to
seven secondary subnets, by entering IP address/ subnet mask pairs:
IP Subnets
IP Address
----------------
#1: 192.128.117.162
Subnet Mask
---------------
255.255.255.0
#2: 0.0.0.0
0.0.0.0
#3:
#4:
#5:
#6:
#7:
#8:
Note: You need not use this screen if you have only a single Ethernet IP subnet. In that case, you can continue
to enter or edit the IP address and subnet mask for the single subnet on the IP Setup screen.
This screen displays up to eight rows of two editable columns, preceded by a row number between one and
eight. If you have eight subnets configured, there will be eight rows on this screen. Otherwise, there will be one
more row than the number of configured subnets. The last row will have the value 0.0.0.0 in both the IP
address and subnet mask fields to indicate that you can edit the values in this row to configure an additional
subnet. All eight row labels are always visible, regardless of the number of subnets configured.
■
To add an IP subnet, enter the Netopia R2121’s IP address on the subnet in the IP Address field in a
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Setup, SmartIP and Network Address Translation 10-11
particular row and the subnet mask for the subnet in the Subnet Mask field in that row.
For example:
IP Subnets
IP Address
----------------
#1: 192.128.117.162
Subnet Mask
---------------
255.255.255.0
#2: 192.128.152.162
255.255.0.0
0.0.0.0
#3: 0.0.0.0
#4:
#5:
#6:
#7:
#8:
■
To delete a configured subnet, set both the IP address and subnet mask values to 0.0.0.0, either explicitly
or by clearing each field and pressing Return or Enter to commit the change. When a configured subnet is
deleted, the values in subsequent rows adjust up to fill the vacant fields.
Note that the subnets configured on this screen are tied to the address serving pools configured on the IP
Address Pools screen, and that changes on this screen may affect the IP Address Pools screen. In particular,
deleting a subnet configured on this screen will delete the corresponding address serving pool, if any, on the IP
Address Pools screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
10-12 User’s Reference Guide
If you have configured multiple Ethernet IP subnets, the IP Setup screen changes slightly:
IP Setup
Subnet Configuration...
Default IP Gateway:
192.128.117.163
Primary Domain Name Server:
Secondary Domain Name Server:
Domain Name:
0.0.0.0
0.0.0.0
Receive RIP:
Transmit RIP:
Static Routes...
Both
v2 (multicast)
Address Serving Setup...
Exported Services...
Filter Sets...
The IP address and Subnet mask items are hidden, and the “Define Additional Subnets...” item becomes
“Subnet Configuration...”. If you select Subnet Configuration, you will return to the IP Subnets screen that
allows you to define IP addresses and masks for additional Ethernet IP subnets.
■
Select Static Routes to manually configure IP routes. See the following section.
Static routes
Static routes are IP routes that are maintained manually. Each static route acts as a pointer that tells the
Netopia R2121 how to reach a particular network. However, static routes are used only if they appear in the IP
routing table, which contains all of the routes used by the Netopia R2121 (see “IP routing table” on page 13-9).
Static routes are helpful in situations where a route to a network must be used and other means of finding the
route are unavailable. For example, static routes are useful when you cannot rely on RIP.
To go to the Static Routes screen, select the Static Routes item in the IP Setup screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Setup, SmartIP and Network Address Translation 10-13
Static Routes
Display/Change Static Route...
Add Static Route...
Delete Static Route...
Configure/View/Delete Static Routes from this and the following Screens.
Viewing static routes
To display a view-only table of static routes, select Display/ Change Static Route in the Static Routes screen.
+-Dest. Network---Subnet Mask-----Next Gateway----Priority-Enabled-+
+------------------------------------------------------------------+
| 0.0.0.0
0.0.0.0
127.0.0.2
Low
Yes
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
+------------------------------------------------------------------+
Select a Static Route to modify.
The table has the following columns:
Dest. Network: The network IP address of the destination network.
Subnet Mask: The subnet mask associated with the destination network.
Next Gateway: The IP address of the router that will be used to reach the destination network.
Download from Www.Somanuals.com. All Manuals Search And Download.
10-14 User’s Reference Guide
Priority: An indication whether the Netopia R2121 will use the static route when it conflicts with information
received from RIP packets.
Enabled: An indication whether the static route should be installed in the IP routing table.
Adding a static route
To add a new static route, select Add Static Route in the Static Routes screen and go to the Add Static Route
screen.
Add Static Route
Static Route Enabled:
Yes
Destination Network IP Address:
0.0.0.0
Destination Network Subnet Mask: 0.0.0.0
Next Gateway IP Address:
Route Priority...
0.0.0.0
High
No
Advertise Route Via RIP:
ADD STATIC ROUTE NOW
CANCEL
Configure a new Static Route in this Screen.
■
■
To install the static route in the IP routing table, select Static Route Enabled and toggle it to Yes. To
remove the static route from the IP routing table, select Static Route Enabled and toggle it to No.
Be sure to read the rules on the installation of static routes in the IP routing table. See “Rules of static
route installation” on page 10-15.
■
■
■
Select Destination Network IP Address and enter the network IP address of the destination network.
Select Destination Network Subnet Mask and enter the subnet mask used by the destination network.
Select Next Gateway IP Address and enter the IP address for the router that the Netopia R2121 will use to
reach the destination network. This router does not necessarily have to be part of the destination network,
but it must at least know where to forward packets destined for that network.
■
Select Route Priority and choose High or Low. High means that the static route takes precedence over RIP
information; Low means that the RIP information takes precedence over the static route.
■
■
If the static route conflicts with a connection profile, the connection profile will always take precedence.
To make sure that the static route is known only to the Netopia R2121, select Advertise Route Via RIP
and toggle it to No. To allow other RIP-capable routers to know about the static route, select Advertise
Route Via RIP and toggle it to Yes. When Advertise Route Via RIP is toggled to Yes, a new item called RIP
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Setup, SmartIP and Network Address Translation 10-15
Metric appears below Advertise Route Via RIP.
With RIP Metric you set the number of routers, from 1 to 15, between the sending router and the
destination router. The maximum number of routers on a packet’s route is 15. Setting RIP Metric to 1
means that a route can involve 15 routers, while setting it to 15 means a route can only involve one router.
■
■
Select ADD STATIC ROUTE NOW to save the new static route, or select CANCEL to discard it and return to
the Static Routes screen.
Up to 16 static routes can be created, but one is always reserved for the default gateway, which is
configured using either Easy Setup or the IP Setup screen in System Configuration.
Modifying a static route
To modify a static route, select Display/ Change Static Route in the Static Routes screen to display a table of
static routes.
Select a static route from the table and go to the Change Static Route screen. The parameters in this screen
are the same as the ones in the Add Static Route screen (see “Adding a static route” on page 10-14).
Deleting a static route
To delete a static route, select Delete Static Route in the Static Routes screen to display a table of static
routes. Select a static route from the table and press Return to delete it. To exit the table without deleting the
selected static route, press the Escape key.
Rules of static route installation
The Netopia R2121 applies certain rules before installing enabled static routes in the IP routing table. An
enabled static route will not be installed in the IP routing table if any of the following conditions are true:
■
The static route’s Next Gateway IP Address matches the IP address used by a connection profile or the
Netopia R2121’s Ethernet port.
■
The static route’s Next Gateway IP Address matches an IP address in the range of IP addresses being
distributed by MacIP or DHCP.
■
■
■
The static route’s Next Gateway IP Address is determined to be unreachable by the Netopia R2121.
The static route’s route information conflicts with a connection profile’s route information.
The connection profile associated with the static route is set for dial-in connections only, and there is no
incoming call connected to that connection profile.
■
The connection profile associated with the static route has a disabled dial-on-demand setting, and there is
no current connection using that connection profile.
A static route is already installed in the IP routing table will be removed if any of the conditions listed above
become true for that static route. However, an enabled static route is automatically reinstalled once the
conditions listed above are no longer true for that static route.
Download from Www.Somanuals.com. All Manuals Search And Download.
10-16 User’s Reference Guide
IP address serving
• Serve DHCP Clients
System
Configuration
Main
Menu
IP Address
Serving
• Serve BootP Clients
• Serve Dynamic WAN Clients
• Serve Mac IP/ KIP Clients
In addition to being a router, the Netopia R2121 is also an IP address server. There are four protocols it can
use to distribute IP addresses.
■
The first, called Dynamic Host Configuration Protocol (DHCP), is widely supported on PC networks, as
well as Apple Macintosh computers using Open Transport and computers using the UNIX operating system.
Addresses assigned via DHCP are “leased” or allocated for a short period of time; if a lease is not
renewed, the address becomes available for use by another computer. DHCP also allows most of the IP
parameters for a computer to be configured by the DHCP server, simplifying setup of each machine.
■
■
■
The second, called BOOTP (also known as Bootstrap Protocol), is the predecessor to DHCP and allows
older IP hosts to obtain most of the information that a DHCP client would obtain. However, in contrast,
BOOTP address assignments are “permanent” since there is no lease renewal mechanism in BOOTP.
The third protocol, called Dynamic WAN, is part of the PPP/ MP suite of wide area protocols used for WAN
connections. It allows remote terminal adapters and NAT-enabled routers to be assigned a temporary IP
address for the duration of their connection.
The fourth protocol, called MacIP, is used only for computers on AppleTalk networks. MacIP provides a
protocol translation (or gateway) function between IP and AppleTalk as well as an IP address assignment
mechanism. Like DHCP, MacIP address assignments are normally temporary, although you may also use
static IP addresses with MacIP.
Since no two hosts can use the same IP address at the same time, make sure that the addresses distributed
by the Netopia R2121, and those that are manually configured are not the same. Each method of distribution
must have its own exclusive range of addresses to draw from.
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Setup, SmartIP and Network Address Translation 10-17
To go to the IP Address Serving screen, select IP Address Serving in the System Configuration screen and
press Return.
IP Address Serving
Number of Client IP Addresses:
1st Client Address:
Client Default Gateway...
5
192.168.6.138
192.168.6.137
Serve DHCP Clients:
DHCP NetBios Options...
Yes
Serve BOOTP Clients:
Yes
Yes
Yes
Serve Dynamic WAN Clients
Serve MacIP/KIP Clients:
MacIP/KIP Static Options...
Enter the maximum number of dynamic IP clients to support.
Configure Address Serving (DHCP, BOOTP, etc.) here.
Follow these steps to configure IP Address Serving:
■
If you enabled IP Address Serving either by using SmartStart or in Easy Setup, DHCP, BootP clients,
Dynamic WAN clients, and MacIP/ KIP clients (if you have the AppleTalk kit installed) are automatically
enabled.
■
Select Number of Client IP Addresses and enter the total number of contiguous IP addresses that the
Netopia R2121 will distribute to the client machines on your local area network.
■
■
In the screen example shown above, five Client IP addresses have been allocated.
Select 1st Client Address and enter the first client IP address that you will allocate to your first client
machine. For instance, on your local area network you may first want to figure out what machines are going
to be allocated specific static IP addresses so that you can determine the pool of IP addresses that you will
be serving addresses from via DHCP, BOOTP, Dynamic WAN, and/ or MacIP.
■
■
Example: Your ISP has given your Netopia R2121 the IP address 192.168.6.137, with a subnet mask of
255.255.255.248. The subnet mask allocated will give you six IP addresses to use when connecting to the
ISP over the Internet (for more information on understanding IP addressing refer to Appendix C,
“Understanding IP Addressing.”). Your address range will be from .137-.143. In this example you would
enter 192.168.6.138 as the 1st client address, as the router itself must have an IP address.
To enable DHCP, select Serve DHCP Clients and toggle it to Yes. DHCP serving is automatic when IP
Address Serving is enabled.
Download from Www.Somanuals.com. All Manuals Search And Download.
10-18 User’s Reference Guide
DHCP NetBIOS Options
If your network uses NetBIOS, you can enable the Netopia R2121 to use DHCP to distribute NetBIOS
information.
NetBIOS stands for Network Basic Input/ Output System. It is a layer of software originally developed by IBM
and Sytek to link a network operating system with specific hardware. NetBIOS has been adopted as an industry
standard. It offers LAN applications, a variety of “hooks” to carry out inter-application communications and data
transfer. Essentially, NetBIOS is a way for application programs to talk to the network. To run an application that
works with NetBIOS, a non-IBM network operating system or network interface card must offer a NetBIOS
emulator. Many vendors either provide a version of NetBIOS to interface with their hardware or emulate its
transport layer communications services in their network products. A NetBIOS emulator is a program provided
by NetWare clients that allow workstations to run applications that support IBM’s NetBIOS calls.
■
Select Serve NetBIOS Options and press Return. The DHCP NetBIOS Options screen appears.
DHCP NetBios Options
Serve NetBios Type:
NetBios Type...
Yes
Type B
Serve NetBios Scope:
NetBios Scope:
No
Serve NetBios Name Server:
NetBios Name Server IP Addr:
No
0.0.0.0
Configure DHCP-served NetBIOS options here.
■
To serve DHCP clients with the type of NetBIOS used on your network, select Serve NetBIOS Type and
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Setup, SmartIP and Network Address Translation 10-19
toggle it to Yes.
■
From the NetBIOS Type pop-up menu, select the type of NetBIOS used on your network.
DHCP NetBios Options
+--------+
Serve NetBios Type:
NetBios Type...
+--------+
| Type B |
| Type P |
| Type M |
| Type H |
+--------+
No
Serve NetBios Scope:
NetBios Scope:
Serve NetBios Name Server:
NetBios Name Server IP Addr:
0.0.0.0
■
■
To serve DHCP clients with the NetBIOS scope, select Serve NetBIOS Scope and toggle it to Yes.
Select NetBIOS Scope and enter the scope.
To serve DHCP clients with the IP address of a NetBIOS name server, select Serve NetBIOS Name Server
and toggle it to Yes.
Select NetBIOS Name Server IP Address and enter the IP address for the NetBIOS name server.
You are now finished setting up DHCP NetBIOS Options. To return to the IP Address Serving screen press
the Escape key once.
■
To enable BootP’s address serving capability, select Serve BOOTP Clients and toggle to Yes.
Note: Addresses assigned through BOOTP are permanently allocated from the IP Address Serving pool
until you release them.
To view all of the IP addresses currently being served by the Netopia R2121, from the Statistics & Logs menu
select Served IP Addresses.
Statistics
& Logs
Main
Menu
Served IP
Addresses
Download from Www.Somanuals.com. All Manuals Search And Download.
10-20 User’s Reference Guide
The Served IP Addresses screen appears.
Served IP Addresses
-IP Address-------Type----Expires--Client Identifier--------------------------
----------------------------------SCROLL UP-----------------------------------
192.168.1.100
192.168.1.101
192.168.1.102
192.168.1.103
192.168.1.104
192.168.1.105
192.168.1.106
192.168.1.107
192.168.1.108
192.168.1.109
192.168.1.110
192.168.1.111
192.168.1.112
192.168.1.113
DHCP
00:59
EN: 08-00-07-16-0c-85
BOOTP 00:44
EN: 00-00-c5-4a-1f-ea
---------------------------------SCROLL DOWN----------------------------------
Lease Management...
EN = Ethernet Address; AT = AppleTalk Address; CP = Profile Name; HX = hex
To release these addresses, select Lease Management.
IP Address Lease Management
Reset All Leases
Release BootP Leases
Reclaim Declined Addresses
Hit RETURN/ENTER, you will return to the previous screen.
Select Release BootP Leases and press Return.
For more lease management information see “Served IP Addresses” on page 13-11.
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Setup, SmartIP and Network Address Translation 10-21
MacIP (Kip Forwarding) Options
When hosts using AppleTalk (typically those using LocalTalk) are not directly connected to an IP network (usually
an Ethernet), they must use a MacIP (AppleTalk-IP) gateway.
The optional Netopia AppleTalk feature enhancement kit provides for this service. A MacIP gateway converts
network traffic into the correct format for AppleTalk or IP, depending on the traffic’s destination. The MacIP
gateway can also distribute IP addresses to AppleTalk computers on the network.
Note: Macintosh computers that have LocalTalk or EtherTalk selected in the MacTCP control panel, or
“AppleTalk (MacIP)” selected in the TCP/ IP control panel, must use the MacIP gateway to communicate with the
Internet or any other IP network. Users should point their MacTCP or TCP/ IP control panel to look in the
LocalTalk zone for the MacIP server. Macintosh computers that have Ethernet selected in the MacTCP or TCP/ IP
control panel can do their own AppleTalk-IP conversions.
Setting up MacIP involves choosing MacIP dynamic address serving and then configuring that type. KIP
forwarding is simply a method for distributing IP addresses to AppleTalk clients.
To go to the MacIP Setup screen, select MacIP/ KIP Clients in the IP Address Serving screen from the System
Configuration menu.
■
Select Serve Mac IP/ KIP Clients and toggle to Yes, to enable MacIP/ KIP address serving capability. This
option is automatically enabled if the AppleTalk kit is installed and IP Address Serving is enabled.
■
Select MacIP/ KIP Static Options and press Return. The MacIP (KIP) Forwarding Setup screen tells the
Netopia R2121 how many static addresses to allocate for MacIP/ KIP clients. The addresses must fall
within the address pool from the previous screen. You will need to enter the number of static MacIP
addresses to reserve in this screen.
Note that the address pool IP range will also be listed for your referral in this screen.
MacIP (KIP) Forwarding Setup
This screen tells the Netopia how many static addresses to allocate for
MacIP/KIP clients. The addresses must fall within one of the address pools
from the previous screen.
Number of Static Addresses:
First Static Client Address:
0
0.0.0.0
Enter the number of static MacIP addresses to reserve here.
Reserve static MacIP addresses for KIP Forwarding here.
You have finished your IP Setup.
Download from Www.Somanuals.com. All Manuals Search And Download.
10-22 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
IPX Setup 11-1
Chapter 11
IPX Setup
Internetwork Packet Exchange (IPX) is the network protocol used by Novell NetWare networks. This chapter
shows you how to configure the Netopia R2121 for routing data using IPX. You also learn how to configure the
This section covers the following topics:
■
■
■
“IPX Features” on page 11-1
“IPX Definitions” on page 11-1
“IPX routing tables” on page 11-7
IPX Features
The Netopia R2121 supports the following IPX features:
■
■
■
■
■
IPX RIP and SAP
NetBIOS broadcast packet forwarding (IPX type 20)
IPX packet filtering definable by source and destination IPX address and socket number, for added security
IPX SAP filtering to aid in optimizing WAN bandwidth
Dial-on-demand features:
■
■
Spoofing of IPX keep-alive, SPX, and server serialization packets
Configurable RIP/ SAP timers on connection profiles
IPX Definitions
This section defines IPX-related protocols such as RIP, SAP and NetBIOS, in addition to other related terms. See
the next section for setup instructions.
Internetwork Packet Exchange (IPX)
IPX is a datagram, connectionless protocol that Novell adapted from Xerox Network System’s (XNS) Internet
Datagram Protocol (IDP). IPX is dynamically routed, and the routing architecture works by “learning” network
addressing automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
11-2 User’s Reference Guide
IPX address
An IPX address consists of a network number, a node number, and a socket number. An IPX network number is
composed of eight hexadecimal digits. The network number must be the same for all nodes on a particular
physical network segment. The node number is composed of twelve hexadecimal digits and is usually the
hardware address of the interface card. The node number must be unique inside the particular IPX network.
Socket numbers correspond to the particular service being accessed.
Socket
A socket in IPX is the equivalent of a port in TCP/ IP. Sockets route packets to different processes within a
single node. Novell has reserved several sockets for use in the NetWare environment:
Field Value
Packet Type
Description
00h
Unknown Packet Type
Used for all packets not clas-
sified by any other type
01h
04h
05h
11h
14h
Routing Information Packet
Service Advertising Packet
Sequenced Packet
Unused for RIP packets
Used for SAP packets
Used for SPX packets
Used for NCP packets
Used for Novell NetBIOS
NetWare Core Protocol Packet
Propagated Packet
Routing Information Protocol (RIP)
RIP, which was also derived from XNS, is a protocol that allows for the bidirectional transfer of routing tables
and provides timing information (ticks), so that the fastest route to a destination can be determined. IPX
routers use RIP to create and dynamically maintain databases of internetwork routing information. See the last
section in this chapter for more information on routing tables.
Service Advertising Protocol (SAP)
SAP is a protocol that provides servers and routers with a method to exchange service information. Using SAP,
servers advertise their services and addresses. Routers collect this information to dynamically update their
routing tables and share it with other routers. These broadcasts keep all routers on the internetwork
synchronized and provide real-time information on accessible servers on the internetwork.
Download from Www.Somanuals.com. All Manuals Search And Download.
IPX Setup 11-3
The following is a list of common SAP server types:
Unknown
0000h
0003h
0004h
0005h
0007h
0009h
0024h
0047h
8000h
Print Queue
File Server
Job Server
Print Server
Archive Server
Remote Bridge Server
Advertising Print Server
Reserved Up To
NetBIOS
NetBIOS is a protocol that performs tasks related to the Transport and Session layers of the OSI model. It can
operate over IPX, using a special broadcast packet known as “IPX Packet type 20” to communicate with IPX
NetBIOS servers.
IPX Spoofing
The Netopia R2121 has several IPX features designed to restrict the traffic on the dial-up link when the unit is
not sending or receiving IPX data. When the link is idle and a user is logged into a Novell server, the server will
send “keep alive” packets to ensure the user is still there. If the link is idle, the “keep alive” packets will be
sent back to the server by the locally connected Netopia R2121 as though they came back from the user
without bringing up the dial-up link.
Similarly, “SPX keep alive” packets are treated in this manner. IPX RIP, and SAP messages will not be sent if the
link is down. Together these features enable the user to remain connected to a Novell server or SPX peer
without bringing up the dial-up link, except to send and receive actual user data.
IPX setup
Network
Protocols
Setup
System
Configuration
Main
Menu
IPX Setup
The IPX Setup screen is where you configure the Ethernet side of the Netopia R2121. The information you enter
here controls how the Router routes IPX traffic.
Consult your network administrator for the IPX setup information you will need before changing any of the
settings in this screen. Changes made in this screen will take effect only after the Netopia R2121 is reset.
Download from Www.Somanuals.com. All Manuals Search And Download.
11-4 User’s Reference Guide
To go to the IPX Setup screen, from the Main Menu select System Configuration and then select Network
Protocols Setup and then select IPX Setup.
Note: If you have completed Easy Setup, the information you have already entered will appear in the IP Setup
options screen.
IPX Setup
IPX Routing:
On
Ethernet Encapsulation...
Ethernet Network Address:
802.3
00000000
Ethernet Path Delay:
Ethernet NetBios Forwarding:
Ethernet Inbound SAP Filter Set...
1
No
<<NONE>>
Default Gateway Address:
Filters and Filter Sets...
IPX Wan Pool Base Address
00000000
00000000
Return/Enter accepts * Tab toggles * ESC cancels.
Set up the basic IPX attributes of your Netopia in this screen.
1. To enable IPX routing, select IPX Routing, toggle it to On, and press Return.
2. To change Ethernet encapsulation from the commonly used 802.3 standard, select Ethernet
Encapsulation and choose a different encapsulation method.
3. Select Ethernet Network Address and enter the network address of the IPX network connected to the
Netopia R2121’s Ethernet port.
Note: If the Ethernet network address is set to zero, the Router will attempt to learn the address from any
configured IPX device on the Ethernet network or from the remote IPX network when a call is established.
4. To change the default path delay, select Ethernet Path Delay and enter a value (in ticks). This value is used
to determine the port cost of using the Ethernet port in IPX RIP calculations.
5. To enable NetBIOS packet forwarding, select Ethernet NetBIOS Forwarding and toggle it to Yes. This
parameter will determine whether “IPX Packet type 20” packets are forwarded on the Ethernet interface.
These packets are used by NetBIOS and some other applications.
6. Select Ethernet Inbound SAP Filter Set to filter incoming IPX SAP advertisements on the Ethernet. By
attaching an incoming SAP filter on the Ethernet, you can restrict the number of SAP entries learned on a
large IPX network to only those required by remote users connecting to the Netopia R2121. An Ethernet
SAP filter must be used with networks that have so many servers advertised that the Netopia R2121 would
otherwise exhaust its internal memory storing server entries.
To attach a SAP filter set, first define the filter set using the Filters and Filter Sets option (see step 8
below). Then select the filter set from the Ethernet Incoming SAP Filter Set pop-up menu. To detach the
filter set, select Detach Filter Set.
Download from Www.Somanuals.com. All Manuals Search And Download.
IPX Setup 11-5
7. Select Default Gateway Address, and enter the network address of the IPX network to which all packets of
unknown destination address should be routed.
Note: The Default Gateway Address is usually set up to match the IPX Address in your network Connection
Profile.
8. To configure filters and filter sets, select Filters and Filter Sets and go to the IPX filters and filter sets
screens. For information on how to configure IPX filters and filter sets, see “IPX filters” on page 14-22.
9. Select IPX Wan Pool Base Address and enter the first IPX network address to be allocated to requesting
IPX WAN clients. The base address you enter must not conflict with other IPX networks assigned to your IPX
internet.
IPX in the answer profile
The answer profile can be configured to accept calls from remote IPX networks. To configure the answer profile
to accept calls from remote IPX networks, from the WAN Configuration menu go to the Default Answer Profile
screen.
WAN
Configuration
Main
Menu
Default Answer
Profile
Note: The Default Answer Profile screen varies according to configuration.
Default Answer Profile
Calling Number Authentication...
Ignored
Must Match a Defined Profile:
Yes
PPP Authentication...
PAP
Configure values which may be used when receiving a call in this screen.
To enable IPX routing in the answer profile, select IPX Enabled and toggle it to Yes. When IPX Enabled is set to
Yes, the item IPX Parameters appears below it.
Download from Www.Somanuals.com. All Manuals Search And Download.
11-6 User’s Reference Guide
To configure IPX routing in the answer profile, select IPX Parameters and go to the IPX Parameters (Default
Answer Profile) screen. The items in this screen are similar to the IPX Profile Parameters items of the same
name (see page 11-5).
IPX Parameters (Default Answer Profile)
NetBios Packet Forwarding:
Off
Incoming Packet Filter Set...
Outgoing Packet Filter Set...
Incoming SAP Filter Set...
Outgoing SAP Filter Set...
Detach Filter Sets...
Periodic RIP Timer:
Periodic SAP Timer:
60
60
Configure IPX values to use when no matching Profile can be found.
Download from Www.Somanuals.com. All Manuals Search And Download.
IPX Setup 11-7
IPX routing tables
Main
Menu
• IPX Routing Table
• IPX SAP Bindery Table
Statistics & Logs
IPX routing tables provide information on current IPX routes and services.
To go to the IPX Routing Table screen, select IPX Routing Table in the Routing Tables screen. This table shows
detailed information about current IPX network routes.
IPX Routing Table
Net Addr-Hops-Ticks-Type--Status-Interface--------------via Router------------
-----------------------------------SCROLL UP----------------------------------
00000020 2
00000030 2
00000033 4
00000100 2
00000110 1
3 RIP Active Ethernet
12 RIP Active Ethernet
14 RIP Active Ethernet
7 RIP Active Ethernet
1 RIP Active Ethernet
00000120:00000c465c2f
00000120:00000c465c2f
000000120:00000c465c2f
00000120:00000c465c2f
00000120:00000c465c2f
---------------------------------SCROLL DOWN-----------------------------
UPDATE
To go to the IPX SAP Bindery Table screen, select IPX SAP Bindery Table in the Routing Tables screen. This
table shows detailed information about available IPX services and their location.
Download from Www.Somanuals.com. All Manuals Search And Download.
11-8 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
AppleTalk Setup 12-1
Chapter 12
AppleTalk Setup
This chapter discusses the concept of AppleTalk routing and how to configure AppleTalk Setup for a Netopia
R2121 with the AppleTalk kit installed.
AppleTalk support is available as a separate kit for the Netopia R2121 Dual Analog Router. Skip this chapter if
This section covers the following topics:
■
■
■
“AppleTalk networks” on page 12-1
“Installing AppleTalk” on page 12-4
“Configuring AppleTalk” on page 12-6
Note: All changes to AppleTalk options require a restart to take effect.
AppleTalk networks
A network is a communication system that connects computers to share information using network services,
such as electronic mail, print spoolers, and file servers. Information is transferred over a cabling system or
WAN using a common set of protocols. You can think of the cabling system as an organization of cities, streets,
and buildings and the protocols as the method of sending letters or packages, as illustrated on the following
pages. A cable is the physical medium (for example, twisted pair or coaxial) over which information travels from
one device to another.
AppleTalk protocol
AppleTalk is a protocol set for local area networks developed by Apple Computer. While initially applied to the
LocalTalk cabling system for connecting Macintosh computers and LaserWriters, it has been expanded to use
other cabling systems, such as Ethernet, as well as the dial-up telephone networks and packet switching
systems. LocalTalk was originally known as the AppleTalk Personal Network system.
Each computer or peripheral device (printer, client, file server) connected to a network is called a node and has
a unique node address, which can be any number from 1 to 254. Whenever you open the Chooser or any
application that communicates with other computers on your network, your application compiles a list of all
node names and addresses. All you see are the names --- for example, “Paul’sMac,” “TechSportsWriter,” or
“2nd Floor AppleShare” --- but your application also knows the node addresses of all these devices.
When you send information, commands, or requests to a printer, server, or another workstation, your
application formats the information into units known as packets. It then attaches the correct address to the
packets and sends them to the AppleTalk software on your computer, which forwards the packets across the
network. Packets also include a return address, so the receiver will know where to reply.
Download from Www.Somanuals.com. All Manuals Search And Download.
12-2 User’s Reference Guide
If the cabling of your network were a street system, then a node address would correspond to a building’s
street address. Node addresses are not permanent. Each AppleTalk device determines its node address at
startup. Although a Macintosh that is starting up will try to use its previous address, the address will often be
different upon restart. This dynamic node addressing scheme prevents conflicts when devices are moved
between networks and simplifies the administrative tasks of a network. If you have only one network, the node
address alone is all the information AppleTalk needs to send a packet from one computer to another.
However, networks can be connected together through routers, such as the Netopia R2121, into an
internetwork (often shortened to internet). Because devices on different networks can have duplicate node
numbers, AppleTalk tells them apart according to an additional part of their addresses: the network number.
The Netopia R2121 assigns a unique network number to each member network. In terms of the city street
metaphor, the network number is similar to the name of the street. Putting a network number together with a
node number fully specifies the address of a node on an internet.
To make the services on an internet manageable, groups of devices on a network can be grouped into zones.
When this is done, selecting a network service (server, etc.) includes choosing a zone from which the service
can be selected. Like network numbers, zone names are assigned by routers.
A routing table is maintained by each AppleTalk router. The table serves as a map of the internet, specifying
the path and distance, in hops, between its router and other networks. The routing table is used to determine
whether a router will forward a data packet and, if so, to which network.
You can use the information in the AppleTalk routing table to observe and diagnose the Netopia R2121’s
current connections to other AppleTalk routers. To go to the AT Routing Table screen from the Netopia R2121’s
console, select Statistics & Logs from the Main Menu and then select AppleTalk Routing Table.
AT Routing Table
-Net---Range--Def Zone Name----------Hops-State-Next Rtr Addr.--Pkts Fwded
----------------------------------SCROLL UP--------------------------
1
2
--
--
--
--
--
--
--
--
--
--
--
--
27
31
Admin
AdMan
2
2
2
2
2
2
2
2
2
2
2
2
1
1
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
0
0
3
Aspirations
Sales
0
4
0
5
Marketing
Molluscs
Customer Service
Telemarketing
Rio
Regiment
Rhinos
Unique Services
Aspirations
Rhinos
0
6
1
7
1
8
0
10
11
12
16
*24
28
0
0
0
0
79
15
---------------------------------SCROLL DOWN-------------------------
UPDATE
'*' Entries have multiple zone names. Return/Enter on these to see zone list.
A router has multiple communications ports and is capable of forwarding information to other routers and
devices on the internet. The router performs packet forwarding, network and device address maintenance, and
other administrative functions required by the AppleTalk protocols.
Download from Www.Somanuals.com. All Manuals Search And Download.
AppleTalk Setup 12-3
MacIP
When Macintosh computers encapsulate TCP/ IP packets in AppleTalk, either because they are on LocalTalk or
they are on EtherTalk for administrative reasons, they must use the services of a MacIP gateway. This gateway
converts network traffic into the correct format for AppleTalk or IP, depending on the traffic’s destination.
Setting up MacIP involves enabling the feature and optionally setting up a range of addresses to be static.
See Chapter 10, “IP Setup, SmartIP and Network Address Translation,” for more information on how to set up
MacIP and other IP addressing schemes.
AURP
AppleTalk Update-Based Routing Protocol (AURP) allows AppleTalk networks to communicate across an IP
network. Your local AppleTalk networks (connected to the Netopia R2121) can exchange data with remote
AppleTalk networks that are also connected to an AURP-capable router.
When two networks using AppleTalk communicate with each other through a network based on the Internet
Protocol, they are said to be tunneling through the IP network. The Netopia R2121 uses AURP to allow your
AppleTalk network to tunnel to designated AppleTalk partner networks, as well as to accept connections from
remote AppleTalk networks tunneling to your AppleTalk LAN.
Routers and seeding
To configure AppleTalk networks, you must understand the concept of seeding. Seeding is the process by which
routers (or more specifically, router ports) agree on what routing information is valid. AppleTalk routers that
have been reset, for example, must decide what zones and network numbers are valid before they begin
routing. In this case, a router may use the information it has stored, or use information it receives from another
router, depending on how it has been configured.
To help ensure agreement between routers on a network, a seed router is configured with the correct
information, and other routers obtain their information from that router when they are turned on or reset.
Routers commonly use one of three types of seeding procedures: hard seeding, soft seeding, and non-seeding.
Hard seeding: When a router that uses hard seeding is turned on or reset, it requests network number and
zone name information from any existing routers on the networks it will serve. If no other routers reply, the
router uses the network numbers and zone names specified in its own configuration. If other routers reply, and
their information matches the router’s own configuration information, the result is the same—the router uses
the values in its own configuration. However, if other routers provide network numbers or zone names that
conflict with those in the router’s configuration, the router disables any of its own ports for which there are
conflicts.
Soft seeding: When a router that uses soft seeding is turned on or reset, it requests network number and zone
name information from any existing routers on the networks it will serve. If no other routers reply, the router
uses the network numbers and zone names specified in its own configuration. If other routers reply, the router
uses the information they provide, regardless of whether or not there are conflicts between the information
received and its configured information. Once a soft- or hard seeding router begins to route, it can serve as a
seed router, providing network number and zone name information to other routers upon request. The default
state of the Netopia R2121’s AppleTalk ports is soft seeding.
Non-seeding: When a router using non-seeding is turned on or reset, it requests network number and zone
name information from any existing routers on the networks it will serve. For any network where no other
routers reply, the non-seeding router will not have any active ports until the next reset.
Download from Www.Somanuals.com. All Manuals Search And Download.
12-4 User’s Reference Guide
You should set the Netopia R2121’s seeding action to work best in your particular network environment. These
scenarios may guide you in deciding how to set the router’s seeding:
■
■
■
If the Netopia R2121 is the only router on your network, you must set it to either hard seeding or soft
seeding. The default is soft seeding.
If there is another active router on your network, and you want that router to configure the Netopia R2121’s
EtherTalk or LocalTalk parameters, you can set the Netopia R2121 to non-seeding.
If there is another active router on your network, you could set the Netopia R2121 to be soft seeding if you
are unsure that the second router would always be available to configure the Netopia R2121’s EtherTalk or
LocalTalk parameters.
■
If you want the Netopia R2121 to configure the EtherTalk or LocalTalk parameters of other routers on your
network, you must set it to hard seeding. In this case, the other routers must be soft seeding or
non-seeding, and the Netopia R2121 must already be active when those other routers are rebooted.
■
If you want the Netopia R2121 and all other routers on your network to use only their own configurations,
set the Netopia R2121 and all other routers to hard seeding. In this case, any router (including the Netopia
R2121) that is rebooted will not begin routing if it detects a routing conflict between itself and any other
router. This last scenario could be useful for detecting and locating routing errors on your network.
Installing AppleTalk
The AppleTalk kit consists of hardware and firmware components that you enable on your router in order to
connect an AppleTalk network. The LocalTalk connector supplied in the AppleTalk feature expansion kit cable
connects to the Auxiliary port on the Netopia R2121.
Netopia R2121 back panel
Ethernet
Phone 2
Phone 1
Telco 1
8
4
7
3
6
2
5
1
Auxiliary
Console
Power
Telco 2
Normal/Uplink
1
Auxiliary connection port
HD-15 (female)
You then enable AppleTalk routing through the Console-based management screens.
To install the AppleTalk features from the Main Menu, go to System Configuration and select Upgrade Feature
Set.
Download from Www.Somanuals.com. All Manuals Search And Download.
AppleTalk Setup 12-5
System
Configuration
Main
Menu
Upgrade
Feature Set
The Netopia Feature Set Upgrade screen appears.
Netopia Feature Set Upgrade
You may be able to extend the features of your Netopia by purchasing a
'Software Upgrade'. For a list of available upgrades, please see the release
notes that came with your Netopia or visit the Netopia Communications web
site at www.netopia.com.
To purchase an upgrade, you must provide your Serial Number, which is:
xx-xx-xx
You will receive an Upgrade Key, which you should enter below.
Upgrade Key:
UPGRADE NOW
CANCEL
Follow the instructions to enable AppleTalk on your router. Once AppleTalk is enabled, you can configure your
network as described in the following sections.
Download from Www.Somanuals.com. All Manuals Search And Download.
12-6 User’s Reference Guide
Configuring AppleTalk
AppleTalk setup for Netopia R2121s consists of configuring EtherTalk, LocalTalk, and AURP.
EtherTalk Setup
To go to the EtherTalk Setup options screen, select Network Protocols Setup and then select AppleTalk Setup
in the System Configuration screen. Select EtherTalk Phase ll Setup and press Return.
EtherTalk Phase II Setup
EtherTalk Phase II Enabled:
Show Zones...
+---------ET II Zone List----------+
+----------------------------------+
| Unnamed
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Enter New Zone Name:
Delete Zone Name...
Set Default Zone...
Net Low:
Net Hi:
Seeding...
+----------------------------------+
Up/Down Arrow Keys to select, ESC to dismiss.
■
■
■
If you are using EtherTalk Phase ll on the Ethernet network connected to Netopia R2121, select EtherTalk
Phase ll Enabled and toggle it to On.
To view the zones available to EtherTalk Phase ll, select Show Zones and press Return. You can dismiss
the list of zones by pressing the Return or Escape key.
Select Enter New Zone Name to enter a new zone name.
Note: Your EtherTalk network number and zone name must match the values in use on the EtherTalk
network.
If another router is already present on the EtherTalk network that you will be connecting to the Netopia
R2121, use the zone names and network numbers used by that router for that EtherTalk network.
Otherwise, your EtherTalk network may experience routing conflicts. The Netopia R2121 supports creating
up to 32 zone names.
As an alternative, you can set EtherTalk seeding to soft seeding and let the Netopia R2121 receive the
zone name and network number from the other router.
■
■
To remove zones from the list, select Delete Zone Name and press Return to see the zones list. Use the
Up and Down Arrow keys to select the zone to delete. Press the Return key to delete it and exit the list.
Press the Escape key to exit the list without deleting any zones.
Select Set Default Zone to choose a different default zone. This is the zone where the Netopia R2121’s
Download from Www.Somanuals.com. All Manuals Search And Download.
AppleTalk Setup 12-7
EtherTalk Phase II port is visible to other AppleTalk nodes. The default zone is also where new AppleTalk
nodes will appear. If you do not set a default zone, the first zone you create will be the default zone.
■
■
You can also set the range of EtherTalk Phase II network numbers. Select Net Low and enter the lower limit
of the network number range. Select Net High and enter the upper limit of the range.
“Routers and seeding” on page 12-3).
You have finished configuring EtherTalk Phase II.
LocalTalk Setup
Note: For instructions on making the physical connections for LocalTalk, see “Connecting to a LocalTalk
network” on page 5-6.
Select LocalTalk Setup in the AppleTalk Setup screen and press Return to the LocalTalk Routing Setup screen.
LocalTalk Setup
LocalTalk Enabled:
LocalTalk Zone Name:
LocalTalk Net Number:
Seeding...
On
Unnamed
33126
Soft-Seeding
Use this screen to set up the LocalTalk Port Routing attributes.
■
If you are using LocalTalk with the Netopia R2121, select LocalTalk Enabled and make sure LocalTalk is
set to On, which is the default.
Note: Since the LocalTalk connector attaches to the Auxiliary port on the router, that port will no longer be
available for a third external modem.
■
Select LocalTalk Zone Name and enter a new or existing zone name.
Note: Your LocalTalk network may already have a zone and network number in place. For the Netopia
R2121’s LocalTalk port to be part of your LocalTalk network, it must have a network number and zone
name that matches the values in use on the LocalTalk network.
If another router is already present on the LocalTalk network that you will be connecting to the Netopia
R2121, use the zone name and network number used by that router for that LocalTalk network. Otherwise,
your LocalTalk network may experience routing conflicts.
Download from Www.Somanuals.com. All Manuals Search And Download.
12-8 User’s Reference Guide
As an alternative, you can set LocalTalk seeding to soft seeding and let the Netopia R2121 receive the
zone name and network number from the other router.
■
■
Select LocalTalk Network Number and enter the desired network number.
Select Seeding. From the pop-up menu, choose the type of seeding for the Netopia R2121’s LocalTalk port
to use (see “Routers and seeding” on page 12-3).
You have finished configuring LocalTalk.
AURP setup
To set up AURP, select AppleTalk Setup from the Network Protocols screen. Select AURP Setup and press
Return.
AURP Setup
AURP Enable:
On
Display/Change Partner...
Add Partner...
Delete Partner...
Enter Free Trade Zone Name:
Accept Connections From...
Configured Partners Only
Advanced Options...
AURP Allows you to connect remote AppleTalk Networks across IP.
■
To activate AURP and enable connections to and from AURP partners, select AURP Enable and toggle it to
On.
Viewing AURP partners
■
To see a table of existing AURP partners, select Display/ Show Partners and press Return.
Note: The Netopia R2121 can define a total of 32 AURP partners.
AURP Free Trade Zone
The Free Trade Zone is an AURP security feature. It allows the Netopia administrator to specify a single
AppleTalk zone that will be the only one visible to the remote side for partners that have this option enabled.
Example:
Download from Www.Somanuals.com. All Manuals Search And Download.
AppleTalk Setup 12-9
Site A has an AURP tunnel to site B. Both sides have multiple zones defined on the EtherTalk port and a unique
zone on their LocalTalk ports. If side A has indicated one of its EtherTalk zones is the Free Trade Zone and has
opted to use the Free Trade Zone option for its tunnel to B, then only this Free Trade Zone will show up on side
B and only those machines or services in the Free Trade Zone will be accessible to side B. All of side A will be
able to see all of side B.
Adding an AURP partner
■
To add a new AURP partner, select Add Partner and press Return to go to the Add AURP Partner screen.
Add AURP Partner
Partner IP Address or Domain Name:
Initiate Connection:
No
No
Restrict to Free Trade Zone:
ADD PARTNER NOW
CANCEL
Enter Information about new Partner.
■
Select Partner IP Address or Domain Name and enter the new AURP partner’s IP address. If you do not
know the remote network’s IP address, enter its domain name. Domain names are the Internet addresses
favored by people (for example, chagall.arts.edu). Domain names are matched to the IP addresses actually
used by IP routers (for example, 163.7.8.202).
■
■
■
To initiate a connection with an AURP partner, select Initiate Connection and toggle it to Yes. This will open
a connection to the remote AppleTalk network after rebooting.
You can choose to restrict this partner to the Free Trade Zone by toggling Restrict to Free Trade Zone to
Yes. See “AURP Free Trade Zone” on page 12-8 for more information.
To add the new AURP partner, select ADD PARTNER NOW. To discard the new AURP partner, select
CANCEL.
Modifying an AURP partner
■
To modify an AURP partner, select Display/ Change Partner in the AURP Setup screen and press Return to
display a table of existing partners.
Use the Up and Down Arrow keys to select a partner, then press Return to go to the Change AURP Partner
screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
12-10 User’s Reference Guide
Deleting an AURP partner
■
To delete an AURP partner, select Delete Partner in the AURP Setup screen and press Return to display a
table of existing partners.
Use the Up and Down Arrow keys to select an AURP partner, then press Return to delete it. Press the
Escape key to exit without deleting a partner.
Receiving AURP connections
■
To control the acceptance of incoming AURP tunnels, select Accept Connections From and choose Anyone
or Configured Partners Only from the pop-up menu. If you choose Anyone, all incoming AURP connections
will be accepted.
The more secure option is Configured Partners Only, which only accepts connections from recognized
AURP partners (the ones you have set up).
Configuring AURP Options
In the AURP Setup screen, Select AURP Options and go to the AURP Options screen. Using AURP can cause a
problem when two networks, one local and one remote, have the same network number. This may cause
network routing ambiguities than can result in routing errors.
AURP Options
Tickle Interval (HH:MM:SS):
Update Interval (HH:MM:SS):
00:00:00
00:00:30
Enable Network Number Remapping:
Yes
Remap into Range
From:
To:
4096
32768
Cluster Remote Networks:
No
No
Enable Hop-Count Reduction:
Return accepts * ESC cancels * Left/Right moves insertion point * Del deletes.
■
Select Tickle Pkt Rqst Interval (HH:MM:SS) and set the timer to indicate how often a tickle or ‘are you
still there’ packet will be sent to the remote AppleTalk Network.
The AURP tickle timer is a parameter that you can set anywhere between 0 and 100 hours. This parameter
tells the AURP partners when to send out an AURP tickle packet. If this value is set to 0, the Netopia
R2121 will never send out a tickle packet. Tickle packets verify that the remote router is working. The
minimum tickle interval is 90 seconds. The maximum tickle interval setting is 99:59:59 (100 hours), which
is the recommendation for small networks.
Download from Www.Somanuals.com. All Manuals Search And Download.
AppleTalk Setup 12-11
Raising the tickle packet interval does not ensure that the AURP tunnel is dropped or not brought up. If any
application on the local network generates AppleTalk traffic destined for the network at the remote end of
the AURP tunnel, the tunnel remains up. For example, if a host on the local network connects to a host on
the remote network using remote access software, the AURP tunnel remains up. The AURP tunnel also
remains up if a local user selects the Chooser and uses an AppleTalk service that involves a remote zone,
such as mounting a remote AppleShare volume.
■
In many AppleTalk internets, individual AppleTalk networks come and go. Routers are designed to notify
each other at the end of their Update Interval every time there's such a change in the network topology.
This will cause the Netopia's WAN link to be brought up. You can opt to minimize what may be unnecessary
calls by changing the Update Interval value to some larger value. At the end of this time window if there has
been a local AppleTalk network change the Netopia R2121 will call any remote AURP partner and forward
the new network information.
■
To enable network number remapping, select Enable Network Number Remapping and toggle it to Yes.
You should enable network number remapping if you plan on using AURP when connecting to unknown
AppleTalk networks. for example when “Accept Connections from Anyone” is enabled. With remapping, the
Netopia R2121 will substitute network numbers not used by your network for the numbers of other remote
networks. These safe remappings will only be used by local routers on your network; remote routers will not
be aware of the remapping.
When network number remapping is enabled, you must choose a safe range of network numbers as a
destination for the remapping. A safe range of network numbers does not intersect your local AppleTalk
network’s range of network numbers.
■
■
■
To choose a destination range for the remapping, select From under Remap into Range and enter a
starting value. Then select To and enter an ending value. Make sure the range you choose is large enough
to accommodate all expected incoming AURP network numbers.
To improve the efficiency of remapping network numbers into a safe range, select Cluster Remote
Networks and toggle it to Yes. This setting takes any number of remote networks being remapped and
causes them to be remapped into a continuous range.
To override the AppleTalk maximum limit of 15 hops, select Enable Hop-Count Reduction and toggle it to
Yes. Hosts on a local AppleTalk network will then “see” AppleTalk destinations across the IP tunnel as
being only one hop away.
AppleTalk allows a packet up to 15 hops (going through 15 AppleTalk routers) to reach its destination.
Packets that must reach destinations more than 15 hops away will not succeed, therefore tunneling from
one large AppleTalk network to another could exceed that limit. In such a case, hop count reduction
enables full network to network communication.
You have finished configuring AURP.
Download from Www.Somanuals.com. All Manuals Search And Download.
12-12 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Tools 13-1
Chapter 13
Monitoring Tools
This chapter discusses the Netopia R2121’s device and network monitoring tools. These tools can provide
statistical information, report on current network status, record events, and help in diagnosing and locating
problems.
■
■
■
■
■
■
■
“Routing Tables” on page 13-8
“Served IP Addresses” on page 13-11
“System Information” on page 13-13
“SNMP” on page 13-13
Quick View status overview
You can get a useful, overall status report from the Netopia R2121 in the Quick View screen. To go to the Quick
View screen, select Quick View in the Main Menu.
Main
Quick View
Menu
The Quick View screen has three status sections:
■
■
■
General status
Current WAN Connection Status
LED Status
The status sections vary according to the interface of your Netopia R2121.
Download from Www.Somanuals.com. All Manuals Search And Download.
13-2 User’s Reference Guide
General Status
Quick View
11/16/1998 04:40:47 PM
Default IP Gateway: 0.0.0.0
Domain Name Server: 0.0.0.0
Domain Name: None Provided
CPU Load: 10% Unused Memory: 541 KB
Call Acct: Disabled
LocalTalk Address: 34448:149
----------------MAC Address--------IP Address-------IPX Address---EtherTalk
Ethernet Hub: 00-00-c5-70-03-48 192.163.1.1
34449: 150
Current WAN Connection Status
Profile Name----------State-%Use-Remote Address-----Est.-More Info--------------
ISP
P1
10% IP 92.163.4.1
Lcl NAT 192.163.100.6
LED Status
-PWR-+-----MODEM1-----+--CON--AUX--+-----MODEM2-----+--EN--+--------LEDS---------
Current Date: The current date; this can be set with the Date and Time utility (see “Date and Time” on
page 8-11).
Default IP Gateway: The router’s default gateway, which may be either manually configured or learned via
DHCP. This is the value you assigned in the Default IP Gateway field on page 7-5. If you are using the router’s
defaults (DHCP and NAT) this value will be 0.0.0.0. If you have assigned an IP address as your default gateway,
it is shown here.
CPU Load: Percentage of the system’s resources being used by all current transmissions.
Unused Memory: The total remaining system memory available for use.
Domain Name Server: If you are using the router’s defaults (DHCP and NAT) this value will be 0.0.0.0. If you
have assigned an IP address as your default gateway, it is shown here.
Call Acct: Shows whether you have enabled or disabled the call accounting features.
Domain Name: the domain name you have assigned, typically the name of your ISP
MAC Address: The Netopia R2121’s hardware address, for those interfaces that support DHCP.
IP Address: The Netopia R2121’s IP address, entered in the IP Setup screen.
IPX Address: The Netopia R2121’s IPX address, entered in the IPX Setup screen.
EtherTalk Address: The Netopia R2121’s AppleTalk address on its EtherTalk Phase II interface, entered in the
EtherTalk Phase II Setup screen (only if the optional AppleTalk feature set is installed).
LocalTalk Address: The Netopia R2121’s AppleTalk address on its LocalTalk interface, entered in the LocalTalk
Setup screen (only if the optional AppleTalk feature set is installed).
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Tools 13-3
Current Status
The current status section is a table showing the current status of the WAN. For example:
WAN Status
Current WAN Connection Status
---Profile Name------State---%Use-Remote Address----Est.-More Info----------
ISP
P1
10 IP 92.163.4.1
Lcl NAT 192.163.100.6
Profile Name: Lists the name of the connection profile being used, if any. This field will also indicate if the line
is in use for a POTS call.
State: Lists the ports in use for this connection.
%Use: Indicates the average percent utilization of the maximum capacity of the channels in use for the
connection.
Remote Address: Shows the IP address of the connected remote router if the connection is using IP.
Otherwise, shows the IPX address of the connected remote router, if using IPX. If the directory number was
entered in the WAN configuration (see “Specifying telephone connections” on page 9-2) it shows the called
directory number if locally originated, otherwise the calling directory number (if available).
Est: Indicates whether the connection was locally (“Lcl”) or remotely (“Rmt”) established.
More Info: Indicates, in order of priority, the NAT address in use for this connection, the IPX address in use (if IP
is also in use), or the ISDN caller identification (if available).
Status lights
This section shows the current real-time status of the Netopia R2121’s status lights (LEDs). It is useful for
remotely monitoring the router’s status. The Quick View screen’s arrangement of LEDs corresponds to the
physical arrangement of LEDs on the router.
LED Status
-PWR-+----MODEM1-----+--CON--AUX--+----MODEM2-----+--EN--+--------LEDS---------
RNG DCD TX RX
- - - -
LNK LNK RNG DCD TX RX DATA | '-'= Off 'G'= Green
- | 'R'= Red 'Y'= Yellow
-
-
-
- - - -
Each LED representation can report one of four states:
R: The letter “R” means the LED is red.
G: The letter “G” means the LED is green.
Y: The letter “Y” means the LED is yellow.
The section “Netopia R2121 Dual Analog Router Status Lights” on page 2-6 describes the meanings of the
colors for each LED.
Download from Www.Somanuals.com. All Manuals Search And Download.
13-4 User’s Reference Guide
Statistics & Logs
Main
Menu
Statistics & Logs
• General Statistics
When you are troubleshooting your Netopia R2121, the Statistics screens provide insight into the recent event
activities of the Router.
From the Main Menu go to Statistics & Logs and select one of the options described in the sections below.
General Statistics
To go to the General Statistics screen, select General Statistics in the Statistics & Logs screen.
General Statistics
General Statistics screen
General Statistics
Physical I/F-----Rx Bytes---Tx Bytes---Rx Pkts---Tx Pkts----Rx Err----Tx Err
Ethernet Hub
LocalTalk
56K Modem 1
56K Modem 2
4404
20958
13294
0
60
0
375
754
0
0
0
0
0
0
0
842
842
0
0
5
0
0
4
0
Network----------Rx Bytes---Tx Bytes---Rx Pkts---Tx Pkts----Rx Err----Tx Err
0
IP
656
1152
2
2
0
AppleTalk
0
23046
0
1115
General Statistics displays information about data traffic on the Netopia R2121’s data ports. This information
is useful for monitoring and troubleshooting your LAN.
The left side of the screen lists total packets received and total packets transmitted for the following protocols:
■
■
■
IP (IP packets on the Ethernet)
IPX (IPX packets on the Ethernet) if IPX is enabled
ET II (AppleTalk packets on Ethernet, using EtherTalk Phase II) if the optional AppleTalk feature set is
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Tools 13-5
installed
■
LT (LocalTalk on the PhoneNET) if the optional AppleTalk feature set is installed
The right side of the table lists the total number of occurrences of each of five types of communication
statistics:
EN Rx Packets: The number of Ethernet packets received.
EN Rx Errors: The number of bad Ethernet packets received.
EN Collisions: An error occurring when Ethernet packets are transmitted simultaneously by nodes on the LAN.
WAN Connection Statistics
The WAN Connection Statistics give the following information about each channel of the point-to-point interface:
■
The number of bytes and packets received through the channel
The number of bytes and packets transmitted through the channel
■
Event Histories
The Netopia R2121 records certain relevant occurrences in event histories. Event histories are useful for
diagnosing problems because they list what happened before, during, and after a problem occurs. You can view
two different event histories: one for the router’s system and one for the WAN. The Netopia R2121’s built-in
battery backup prevents loss of event history from a shut down or reset.
The Router’s event histories are structured to display the most recent events first, and to make it easy to
distinguish error messages from informational messages. Error messages are prefixed with an asterisk. Both
the WAN Event History and the Device Event History retain records of the 128 most recent events.
To go to the Event Histories screens, select either WAN Event History or Device Event History in the Statistics
& Logs screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
13-6 User’s Reference Guide
Statistics & Logs
WAN Event History...
Device Event History...
IP Routing Table...
IPX Routing Table...
IPX SAP Bindery Table...
AppleTalk Routing Table...
Served IP Addresses...
General Statistics...
System Information...
WAN Event History
The WAN Event History screen lists a total of 128 events on the WAN. The most recent events appear at the
top.
To go to the WAN Event History screen, select WAN Event History in the Statistics & Logs screen.
WAN Event History
Current Date -- 11/22/98 01:57:07 AM
-Date-----Time-----Event------------------------------------------------------
----------------------------------SCROLL UP-----------------------------------
11/22/98 01:56:49 PPP: BACP negotiated, session 1
11/22/98 01:56:49 PPP: CCP negotiated, session 1, type: Ascend LZS
11/22/98 01:56:49 PPP: IPXCP negotiated, session 1
11/22/98 01:56:49 PPP: IPCP negotiated, session 1, rem: 163.176.249.1
11/22/98 01:56:49 PPP: MP negotiated, session 1
11/22/98 01:56:49 PPP: PAP remote accepted us, Channel 1
11/22/98 01:56:49 PPP: NCP up, session 1, Channel 1
11/22/98 01:56:46 PPP: Channel 1 up, Dialout
11/22/98 01:56:46 Received Connect Ind. for DN: 92384175
11/22/98 01:56:46 >>WAN: data link activated at 115 Kbps
11/22/98 01:56:46 ASYNC: Modem carrier detected (more)
11/22/98 01:56:24 >>Issued Speech Setup Request from our DN: (not supplied)
11/22/98 01:56:07 Link 1 down: PPP PAP failure
11/22/98 01:56:07 Issued Clear Response to DN: (not supplied)
---------------------------------SCROLL DOWN----------------------------------
Clear History...
Return/Enter on event item for details or SCROLL [UP/DOWN] item for scrolling.
Each entry in the list contains the following information:
Time: Time of the event.
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Tools 13-7
Date: Date of the event.
Event: A brief description of the event.
Ch.: The channel involved in the event.
Dir. Number: The directory number (number dialed) involved in the event.
The first event in each call sequence is marked with double arrows (>>).
Failures are marked with an asterisk (*).
If the event history exceeds the size of the screen, you can scroll through it by using the SCROLL UP and
SCROLL DOWN items.
To scroll up, select the SCROLL UP item at the top of the list and press the Return key. To scroll down, select
the SCROLL DOWN item at the bottom of the list and press the Return key.
To get more information about any event listed in the WAN Event History, select the event and then press the
Return key. A dialog box containing more information about the selected event will appear. Press Return or the
Escape key to dismiss the dialog box.
To clear the Event History, select Clear History at the bottom of the history screen and press Return.
Device Event History
The Device Event History screen lists a total of 128 port and system events, giving the time and date for each
event, as well as a brief description. The most recent events appear at the top.
To go to the Device Event History screen, select Device Event History in the Statistics & Logs screen.
Device Event History
Current Date -- 11/22/98 02:03:27 AM
-Date-----Time-----Event------------------------------------------------------
----------------------------------SCROLL UP-----------------------------------
11/22/98 02:03:18 AURP initialization complete
11/22/98 02:03:18 AppleTalk initialization complete
11/22/98 02:03:11 IPX initialization complete
11/22/98 02:03:11 IP address server initialization complete
11/22/98 02:03:11 --BOOT: Warm start v4.3
---------------------------------
11/22/98 02:02:32 IPX initialization complete
11/22/98 02:02:32 IP address server initialization complete
11/22/98 02:02:32 --BOOT: Warm start v4.3
---------------------------------
11/22/98 01:59:50 * IP: Route 0.0.0.0/0.0.0.0 not installed
11/22/98 01:59:50 IPX initialization complete
11/22/98 01:59:50 IP address server initialization complete
11/22/98 01:59:50 --BOOT: Cold start v4.3
---------------------------------
11/22/98 01:55:12 AppleTalk initialization complete
11/22/98 01:55:07 * IP: Route 0.0.0.0/0.0.0.0 not installed
---------------------------------SCROLL DOWN----------------------------------
Clear History...
Return/Enter on event item for details or SCROLL [UP/DOWN] item for scrolling.
If the event history exceeds the size of the screen, you can scroll through it by using the SCROLL UP and
SCROLL DOWN items.
To scroll up, select the SCROLL UP item at the top of the list and press the Return key. To scroll down, select
the SCROLL DOWN item at the bottom of the list and press Return.
Download from Www.Somanuals.com. All Manuals Search And Download.
13-8 User’s Reference Guide
To obtain more information about any event listed in the Device Event History, select the event and then press
Return. A dialog box containing more information about the selected event will appear. Press Return or the
Escape key to dismiss the dialog box.
To clear the Device Event History, select Clear Device Event History in the Event Histories screen and press
Return.
Routing Tables
You can view all of the IP, IPX and AppleTalk routes in the Netopia R2121’s IP, IPX and AppleTalk routing tables,
respectively.
To go to a Routing Table screen, select the Routing Table you are interested in from the Statistics & Logs
screen.
Each of the routing table screens represents a “snapshot” of the routing table information at the time the
screen is first invoked. To take a new snapshot, select Update at the bottom of the screen and press Return.
Statistics & Logs
WAN Event History...
Device Event History...
IP Routing Table...
IPX Routing Table...
IPX SAP Bindery Table...
AppleTalk Routing Table...
Served IP Addresses...
General Statistics...
System Information...
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Tools 13-9
IP routing table
The IP routing table displays all of the IP routes currently known to the Netopia R2121.
To display the IP Routing Table screen, select IP Routing Table in the Statistics & Logs screen and press
Return.
IP Routing Table
Network Address-Subnet Mask-----via Router------Port------------------Type----
----------------------------------SCROLL UP-----------------------------------
0.0.0.0
255.0.0.0
0.0.0.0
--
Other
Local
Local
Local
Bcast
Other
Bcast
127.0.0.1
192.168.1.0
192.168.1.1
192.168.1.15
224.0.0.0
255.255.255.255 127.0.0.1
255.255.255.240 192.168.1.1
255.255.255.255 192.168.1.1
255.255.255.255 192.168.1.15
Loopback
Ethernet
Ethernet
Ethernet
--
224.0.0.0
0.0.0.0
255.255.255.255 255.255.255.255 255.255.255.255 --
---------------------------------SCROLL DOWN----------------------------------
UPDATE
IPX routing table
The IPX routing table displays all of the IPC routes currently known to the Netopia R2121.
To display the IPX Routing Table screen, select IPX Routing Table in the Statistics & Logs screen and press
Return.
IPX Sap Bindery table
The IPX Sap Bindery table displays all of the IPX Sap Bindery routes currently known to the Netopia R2121.
To display the IPX SAP Bindery Table screen, select IPX Sap Bindery Table in the Statistics & Logs screen and
press Return.
AppleTalk routing table
The AppleTalk routing table displays information about the current state of AppleTalk networks connected to the
Netopia R2121, including remote AppleTalk networks connected with AURP. This information is gathered from
other active AppleTalk routers.
Download from Www.Somanuals.com. All Manuals Search And Download.
13-10 User’s Reference Guide
To display the AppleTalk Routing Table screen, select AppleTalk Routing Table in the Statistics & Logs screen
and press Return.
AT Routing Table
-Net---Range--Def Zone Name----------Hops-State-Next Rtr Addr.--Pkts Fwded
----------------------------------SCROLL UP--------------------------
1
2
--
--
--
--
--
--
--
--
--
--
--
--
27
31
Admin
AdMan
2
2
2
2
2
2
2
2
2
2
2
2
1
1
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
Good 46.131
0
0
3
Aspirations
Sales
0
4
0
5
Marketing
Molluscs
Customer Service
Telemarketing
Rio
Regiment
Rhinos
Unique Services
Aspirations
Rhinos
0
6
1
7
1
8
0
10
11
12
16
*24
28
0
0
0
0
79
15
---------------------------------SCROLL DOWN-------------------------
UPDATE
'*' Entries have multiple zone names. Return/Enter on these to see zone list.
Each row in the AppleTalk routing table corresponds to an AppleTalk route or network range. If the list of routes
shown exceeds the size of the screen, you can scroll through it by using the SCROLL UP and SCROLL DOWN
items.
To scroll up, select the SCROLL UP item at the top of the table and press the Return key. To scroll down, select
the SCROLL DOWN item at the bottom of the table and press the Return key.
The table has the following columns:
Net: Displays the starting network number supplied by the AppleTalk router in the ‘Next Rtr Addr. Column’. If a
network number is preceded by an asterisk (*), it has multiple zones. To display the zones, select the network
entry and press Return.
Range: Displays the ending network number for the extended network.
(Def) Zone Name: Displays the zone or zones associated with the specified network or network range. The zone
name shown is either the only zone or the default zone name for an extended network. To see the complete list
of zones for an extended network with multiple zones, select the entry in the table and press the Return key.
Press the Return key again to close the list of zones.
Hops: Displays the number of routers between the Netopia R2121 and the specified network.
State: Displays the state of the specified route, based on the frequency of Routing Table Maintenance Protocol
(RTMP) packets received for the route. The state can be Good, Suspect, or Bad. AppleTalk routers regularly
exchange RTMP packets to update AppleTalk routing information.
Next Rtr Addr.: Displays the DDP or IP address of the next hop for the specified route. A DDP address is
displayed if the router shown is on the local AppleTalk network. DDP address means that a connection to the
next hop router is by a native AppleTalk network (e.g.: LocalTalk or EtherTalk Phase II). An IP address is
displayed if the Netopia R2121 is connected to the router shown using AURP. IP address means a connection
transports over AURP (AppleTalk encapsulated IP).
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Tools 13-11
Pkts Fwded: The number of packets sent to the router shown.
Served IP Addresses
You can view all of the IP addresses currently being served by the Netopia R2121 Dual Analog Router from the
Served IP Addresses screen. From the Statistics & Logs menu, select Served IP Addresses.
The Served IP Addresses screen appears.
Served IP Addresses
-IP Address-------Type----Expires--Client Identifier--------------------------
----------------------------------SCROLL UP-----------------------------------
192.168.1.100
192.168.1.101
192.168.1.102
192.168.1.103
192.168.1.104
192.168.1.105
192.168.1.106
192.168.1.107
192.168.1.108
192.168.1.109
192.168.1.110
192.168.1.111
192.168.1.112
192.168.1.113
DHCP
DHCP
00:36
00:58
EN: 00-00-c5-4a-1f-ea
EN: 08-00-07-16-0c-85
---------------------------------SCROLL DOWN----------------------------------
Lease Management...
EN = Ethernet Address; AT = AppleTalk Address; CP = Profile Name; HX = hex
You can manage DHCP leases by selecting Lease Management in this screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
13-12 User’s Reference Guide
The IP Address Lease Management screen appears.
IP Address Lease Management
Reset All Leases
Release BootP Leases
Reclaim Declined Addresses
Hit RETURN/ENTER, you will return to the previous screen.
By selecting each of these options you can:
■
Reset all current IP addresses leased through DHCP without waiting for the default one hour lease period
to elapse
■
■
Release BootP leases that may be in place, and which may no longer be required
Reclaim served leases that have been declined, for example by devices which may no longer be on the
network.
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Tools 13-13
System Information
The System Information screen gives a summary view of the general system level values in the Netopia R2121
Dual Analog Router. From the Statistics & Logs menu select System Information.
The System Information screen appears.
System Information
Serial Number
Firmware Version
7340872
4.3
Processor Speed (MHz)
Flash ROM Capacity (MBytes)
DRAM Capacity (MBytes)
33
1
4
Ethernet
8 Port 10Base-T
LocalTalk
56K Modem
Auxiliary Serial Port
WAN 1 Interface
WAN 2 Interface
56K Modem
AppleTalk Feature Set
Installed
SNMP
The Netopia R2121 includes a Simple Network Management Protocol (SNMP) agent, allowing monitoring and
configuration by a standard SNMP manager.
The Netopia R2121 supports the following Management Information Base (MIB) documents:
■
■
■
■
■
MIB II (RFC 1213)
Interface MIB (RFC 1229)
Ethernet MIB (RFC 1643)
AppleTalk MIB-I (RFC 1243)
Netopia MIB
These MIBs are on the Netopia R2121 CD included with the Netopia R2121. You should load these MIBs into
your SNMP management software in the order they are listed here. Follow the instructions included with your
SNMP manager on how to load MIBs.
Download from Www.Somanuals.com. All Manuals Search And Download.
13-14 User’s Reference Guide
The SNMP Setup screen
To go to the SNMP Setup screen from the Main Menu, select SNMP in the System Configuration screen and
press Return.
System
Configuration
Main
Menu
SNMP
SNMP Setup
System Name:
System Location:
System Contact:
Read-Only Community String:
Read/Write Community String:
public
private
Authentication Traps Enable:
IP Trap Receivers...
Off
Configure optional SNMP parameters from here.
Follow these steps to configure the first three items in the screen:
1. Select System Name and enter a descriptive name for the Netopia R2121’s SNMP agent.
2. Select System Location and enter the router’s physical location (room, floor, building, etc.).
3. Select System Contact and enter the name of the person responsible for maintaining the router.
System Name, System Location, and System Contact set the values returned by the Netopia R2121 SNMP
agent for the SysName, SysLocation, and SysContact objects, respectively, in the MIB-II system group. Although
optional, the information you enter in these items can help a system administrator manage the network more
efficiently.
Community strings
The Read-Only Community String and the Read/ Write Community String are like passwords that must be used
by an SNMP manager querying or configuring the Netopia R2121. An SNMP manager using the Read-Only
Community String can examine statistics and configuration information from the router, but cannot modify the
router’s configuration. An SNMP manager using the Read/ Write Community String can both examine and
modify configuration parameters.
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Tools 13-15
By default, the read-only and read/ write community strings are set to “public” and “private,” respectively. You
should change both of the default community strings to values known only to you and trusted system adminis-
trators.
To change a community string, select it and enter a new value.
Starting with the version 4.3 firmware, setting the Read-Only and Read-Write community strings to the empty
string will block all SNMP requests to the router. (The router may still send SNMP Traps if those are properly
enabled.)
Previously, if either community string was the empty string, SNMP Requests specifying an empty community
string were accepted and processed.
This change is designed to allow the administrator to block SNMP access to the router, and to provide more
granular control over the allowed SNMP operations to the router.
■
■
Setting only the Read-Write community string to the empty string will block SNMP Set Requests to the
router, but Get Requests and Get-Next Requests will still be honored using the Read-Only community string
(assuming that is not the empty string).
Setting only the Read-Only community string to the empty string will not block Get Requests or Get-Next
Requests since those operations (and Set Requests) are still allowed using the (non-empty) Read-Write
community string.
Caution!
Even if you decide not to use SNMP, you should change the community strings. This prevents unauthorized
access to the Netopia R2121 through SNMP. For more information on security issues, see “Suggested security
measures” on page 14-1.
SNMP traps
An SNMP trap is an informational message sent from an SNMP agent (in this case, the Netopia R2121) to a
manager. When a manager receives a trap, it may log the trap as well as generate an alert message of its own.
Standard traps generated by the Netopia R2121 include the following:
■
An authentication failure trap is generated when the router detects an incorrect community string in a
received SNMP packet. Authentication Traps Enable must be On for this trap to be generated.
■
■
A cold start trap is generated after the router is reset.
An interface down trap (ifDown) is generated when one of the router’s interfaces, such as a port, stops
functioning or is disabled.
■
An interface up trap (ifUp) is generated when one of the router’s interfaces, such as a port, begins
functioning.
The Netopia R2121 sends traps using UDP (for IP networks).
You can specify which SNMP managers are sent the IP traps generated by the Netopia R2121. Up to eight
receivers can be set. You can also review and remove IP traps.
Go to the IP Trap Receivers screen by selecting IP Trap Receivers in the SNMP Setup screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
13-16 User’s Reference Guide
IP Trap Receivers
Display/Change IP Trap Receiver...
Add IP Trap Receiver...
Delete IP Trap Receiver...
Return/Enter to modify an existing Trap Receiver.
Navigate from here to view, add, modify and delete IP Trap Receivers.
Setting the IP trap receivers
1. Select Add IP Trap Receiver.
2. Select Receiver IP Address or Domain Name. Enter the IP address or domain name of the SNMP manager
you want to receive the trap.
3. Select Community String if you enabled one in the SNMP Setup screen, and enter the appropriate
password.
4. Select Add Trap Receiver Now and press Return. You can add up to seven more receivers.
Viewing IP trap receivers
To display a view-only table of IP trap receivers, select Display/ Change IP Trap Receiver in the IP Trap
Receivers screen.
Modifying IP trap receivers
1. To edit an IP trap receiver, select Display/ Change IP Trap Receiver in the IP Trap Receivers screen.
2. Select an IP trap receiver from the table and press Return.
3. In the Change IP Trap Receiver screen, edit the information as needed and press Return.
Deleting IP trap receivers
1. To delete an IP trap receiver, select Delete IP Trap Receiver in the IP Trap Receivers screen.
2. Select an IP trap receiver from the table and press Return.
3. In the dialog box, select Continue and press Return.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-1
Chapter 14
Security
The Netopia R2121 provides a number of security features to help protect its configuration screens and your
local network from unauthorized access. Although these features are optional, it is strongly recommended that
you use them.
This section covers the following topics:
■
■
“Suggested security measures” on page 14-1, lists actions for blocking potential security holes.
“User accounts,” beginning on page 14-2, shows you how to set up name/ password combinations to
protect the Netopia R2121’s configuration screens.
■
■
“Dial-in Console Access” on page 14-3
“Telnet access” on page 14-4, shows you how to control access to the Netopia R2121 by those using the
■
beginning on page 14-12, have information on what filters are, how they work, how to customize them, and
how to use them in sets. For information on IPX filters and filter sets, see “IPX filters,” beginning on
page 14-22.
■
■
“Firewall tutorial” on page 14-30
“Token Security Authentication” on page 14-37
Suggested security measures
In addition to setting up user accounts, Telnet access, and filters (all of which are covered later in this chapter),
there are other actions you can take to make the Netopia R2121 and your network more secure:
■
Change the SNMP community strings (or passwords). The default community strings are universal and
could easily be known to a potential intruder.
■
■
■
■
Set the answer profile so it must match incoming calls to a connection profile.
Use CallerID.
Leave the “Enable Dial-in Console Access” option set to No.
Where possible, insist on using PAP, CHAP, or secure authentication token card to authenticate
connections to and from connection profiles.
■
■
When using AURP, accept connections only from configured partners.
Configure the Netopia R2121 through the serial console port to ensure that your communications cannot
be intercepted.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-2 User’s Reference Guide
User accounts
When you first set up and configure the Netopia R2121, no passwords are required to access the configuration
screens. Anyone could tamper with the router’s configuration by simply connecting it to a console.
However, by adding user accounts, you can protect the most sensitive screens from unauthorized access. User
accounts are composed of name/ password combinations that can be given to authorized users.
Caution!
You are strongly encouraged to add protection to the configuration screens. Unprotected screens could allow an
unauthorized user to compromise the operation of your entire network.
Once user accounts are created, users who attempt to access protected screens will be challenged. Users who
enter an incorrect name or password are returned to a screen requesting a name/ password combination to
access the Main Menu.
To set up user accounts, select Security in the System Configuration screen and go to the Security Options
screen.
Security Options
Enable Dial-in Console Access:
Yes
Yes
Enable SmartStart/SmartView/Web Server:
Enable Telnet Console Access:
Enable Telnet Access to SNMP Screens:
Yes
Yes
Show Users...
Add User...
Delete User...
Password for This Screen (11 chars max):
Return/Enter accepts * Tab toggles * ESC cancels.
Set up configuration access options here.
Protecting the Security Options screen
The first screen you should protect is the Security Options screen, because it controls access to the
configuration screens. Access to the Security Options screen can be protected with a password.
Select Password for This Screen in the Security Options screen and enter a password. Make sure this
password is secure and is different from any of the user account passwords.
Protecting the configuration screens
You can protect the configuration screens with user accounts. You can administer the accounts from the
Security Options screen. You can create up to four accounts.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-3
To display a view-only list of user accounts, select Show Users in the Security Options screen.
To add a new user account, select Add User in the Security Options screen and press Return to go to the Add
Name With Write Access screen.
Add Name With Write Access
Enter Name:
Enter Password (11 characters max):
ADD NAME/PASSWORD NOW
CANCEL
Follow these steps to configure the new account:
1. Select Enter Name and enter a descriptive name (for example, the user’s first name).
2. Select Enter Password and enter a password.
3. To accept the new name/ password combination, select ADD NAME/ PASSWORD NOW. To exit the Add
Name With Write Access screen without saving the new account, select CANCEL.
To delete a user account, select Delete User to display a list of accounts. Select an account from the list and
press Return to delete it. To exit the list without deleting the selected account, press the Escape key.
Dial-in Console Access
Remote modem terminal emulator setups can dial in to either internal modem line and establish a remote
console session, even though they are not using PPP. This allows Netopia Inc.'s “Up and Running, Guaranteed!”
department or other administrator with the appropriate security to remotely configure your router for you. If you
used SmartStart to configure your router, this option will be set to “No”.
■
To prevent any remote caller from establishing a remote session, leave the option Enable Dial-in Console
Access set to “No”.
■
To allow access for Up and Running, Guaranteed! with the default name and password in place, toggle this
option to “Yes”.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-4 User’s Reference Guide
Enable SmartStart/SmartView/Web Server
You may wish to restrict access to the web-based screens to prevent inadvertent switching or connecting and
disconnecting of Connection Profiles. Since SmartStart can be used to reconfigure the router, you may wish to
block inadvertent damage resulting from unauthorized use of SmartStart. To prevent access to these features
toggle this option to “No”.
Telnet access
Telnet is a TCP/ IP service that allows remote terminals to access hosts on an IP network. The Netopia R2121
supports Telnet access to its configuration screens.
Caution!
You should consider password-protecting or restricting Telnet access to the Netopia R2121 if you suspect there
is a chance of tampering.
To password-protect the configuration screens, select Easy Setup from the Main Menu, and go to the Easy
Setup Security Configuration screen. By entering a Name and Password pair in this screen, all access via
serial, Telnet, SNMP, and web server will be password-protected.
To restrict Telnet access, select Security in the Advanced Configuration Menu and go to the Security Options
screen. There are two levels of Telnet restriction available:
To restrict Telnet access to the SNMP screens, select Enable Telnet Access to SNMP Screens and toggle it to
No. (See “SNMP traps” on page 13-15.)
To restrict Telnet access to all of the configuration screens, select Enable Telnet Console Access and toggle it
to No.
About filters and filter sets
Security should be a high priority for anyone administering a network connected to the Internet. Using packet
filters to control network communications can greatly improve your network’s security.
The Netopia R2121’s packet filters are designed to provide security for the Internet connections made to and
from your network. You can customize the router’s filter sets for a variety of packet filtering applications.
Typically, you use filters to selectively admit or refuse TCP/ IP connections from certain remote networks and
specific hosts. You will also use filters to screen particular types of connections. This is commonly called
firewalling your network.
Before creating filter sets, you should read the next few sections to learn more about how these powerful
security tools work.
What’s a filter and what’s a filter set?
A filter is a rule that lets you specify what sort of data can flow in and out of your network. A particular filter can
either be an input filter—one that is used on data (packets) coming in to your network from the Internet—or an
output filter—one that is used on data (packets) going out from your network to the Internet.
A filter set is a group of filters that work together to check incoming or outgoing data. A filter set can consist of
a combination of input and output filters.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-5
How filter sets work
A filter set acts like a team of customs inspectors. Each filter is an inspector through which incoming and
outgoing packages must pass. The inspectors work as a team, but each inspects every package individually.
Each inspector has a specific task. One inspector’s task may be to examine the destination address of all
outgoing packages. That inspector looks for a certain destination—which could be as specific as a street
address or as broad as an entire country—and checks each package’s destination address to see if it matches
that destination.
FROM:
FROM:
FROM:
T
TO:
TO:
A filter inspects data packets like a customs inspector scrutinizing packages.
Filter priority
Continuing the customs inspectors analogy, imagine the inspectors lined up to examine a package. If the
package matches the first inspector’s criteria, the package is either rejected or passed on to its destination,
depending on the first inspector’s particular orders. In this case, the package is never seen by the remaining
inspectors.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-6 User’s Reference Guide
packet
first
filter
no
match?
yes
send
to next
filter
pass or
discard?
discard
(delete)
pass
to network
If the package does not match the first inspector’s criteria, it goes to the second inspector, and so on. You can
see that the order of the inspectors in the line is very important.
For example, let’s say the first inspector’s orders are to send along all packages that come from Rome, and the
second inspector’s orders are to reject all packages that come from France. If a package arrives from Rome,
the first inspector sends it along without allowing the second inspector to see it. A package from Paris is
ignored by the first inspector, rejected by the second inspector, and never seen by the others. A package from
London is ignored by the first two inspectors, and so it’s seen by the third inspector.
In the same way, filter sets apply their filters in a particular order. The first filter applied can pass or discard a
packet before that packet ever reaches any of the other filters. If the first filter can neither pass nor discard the
packet (because it cannot match any criteria), the second filter has a chance to pass or reject it, and so on.
Because of this hierarchical structure, each filter is said to have a priority. The first filter has the highest priority,
and the last filter has the lowest priority.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-7
How individual filters work
As described above, a filter applies criteria to an IP packet and then takes one of three actions:
A filter’s actions
■
■
■
Passes the packet to the local or remote network
Blocks (discards) the packet
Ignores the packet
A filter passes or blocks a packet only if it finds a match after applying its criteria. When no match occurs, the
filter ignores the packet.
The criteria are based on information contained in the packets. A filter is simply a rule that prescribes certain
actions based on certain conditions. For example, the following rule qualifies as a filter:
A filtering rule
Block all Telnet attempts that originate from the remote host 199.211.211.17.
This rule applies to Telnet packets that come from a host with the IP address 199.211.211.17. If a match
occurs, the packet is blocked.
Here is what this rule looks like when implemented as a filter on the Netopia R2121:
+-#--Source IP Addr--Dest IP Addr-----Proto-Src.Port-D.Port--On?-Fwd-+
+--------------------------------------------------------------------+
| 1 199.211.211.17 0.0.0.0
+--------------------------------------------------------------------+
TCP 23
Yes No |
To understand this particular filter, look at the parts of a filter.
Parts of a filter
A filter consists of criteria based on packet attributes. A typical filter can match a packet on any one of the
following attributes:
■
■
■
The source IP address (where the packet was sent from)
The destination IP address (where the packet is going)
The type of higher-layer Internet protocol the packet is carrying, such as TCP or UDP
Download from Www.Somanuals.com. All Manuals Search And Download.
14-8 User’s Reference Guide
Port numbers
A filter can also match a packet’s port number attributes, but only if the filter’s protocol type is set to TCP or
UDP, since only those protocols use port numbers. The filter can be configured to match the following:
■
■
The source port number (the port on the sending host that originated the packet)
The destination port number (the port on the receiving host that the packet is destined for)
By matching on a port number, a filter can be applied to selected TCP or UDP services, such as Telnet, FTP, and
World Wide Web. The tables below show a few common services and their associated port numbers..
Internet service
FTP
TCP port
Internet service
Finger
TCP port
20/ 21
23
79
80
Telnet
World Wide Web
News
SMTP (mail)
Gopher
25
144
513
70
rlogin
Internet service
UDP port
Internet service
UDP port
Who Is
43
AppleTalk Routing
202
Maintenance (at-rtmp)
World Wide Web
80
AppleTalk Name Binding
(at-nbp)
202
SNMP
TFTP
161
69
AURP (AppleTalk)
who
387
513
Port number comparisons
A filter can also use a comparison option to evaluate a packet’s source or destination port number. The
comparison options are:
No Compare: No comparison of the port number specified in the filter with the packet’s port number.
Not Equal To: For the filter to match, the packet’s port number cannot equal the port number specified in the
filter.
Less Than: For the filter to match, the packet’s port number must be less than the port number specified in the
filter.
Less Than or Equal: For the filter to match, the packet’s port number must be less than or equal to the port
number specified in the filter.
Equal: For the filter to match, the packet’s port number must equal the port number specified in the filter.
Greater Than: For the filter to match, the packet’s port number must be greater than the port number specified
in the filter.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-9
Greater Than or Equal: For the filter to match, the packet’s port number must be greater than or equal to the
port number specified in the filter.
Other filter attributes
There are three other attributes to each filter:
■
■
■
The filter’s order (i.e., priority) in the filter set
Whether the filter is currently active
Whether the filter is set to pass (forward) packets or to block (discard) packets
Putting the parts together
When you display a filter set, its filters are displayed as rows in a table:
+-#---Source IP Addr---Dest IP Addr-----Proto-Src.Port-D.Port--On?-Fwd-+
+----------------------------------------------------------------------+
| 1 192.211.211.17 0.0.0.0
TCP 0
23
=6000 Yes No |
Yes No |
| 2 0.0.0.0
| 3 0.0.0.0
| 4 0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
TCP NC
ICMP --
TCP NC
UDP NC
--
Yes Yes |
>1023 Yes Yes |
| 5 0.0.0.0
>1023 Yes Yes |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
+----------------------------------------------------------------------+
The table’s columns correspond to each filter’s attributes:
#: The filter’s priority in the set. Filter number 1, with the highest priority, is first in the table.
Source IP Addr: The packet source IP address to match.
Dest IP Addr: The packet destination IP address to match.
Proto: The protocol to match. This can be entered as a number (see the table below) or as TCP or UDP if using
those protocols.
Protocol
Number to use
Full name
N/ A
ICMP
TCP
0
1
6
Ignores protocol type
Internet Control Message Protocol
Transmission Control Protocol
Download from Www.Somanuals.com. All Manuals Search And Download.
14-10 User’s Reference Guide
Protocol
UDP
Number to use
Full name
17
User Datagram Protocol
Src. Port: The source port to match. This is the port on the sending host that originated the packet.
D. Port: The destination port to match. This is the port on the receiving host for which the packet is intended.
On?: Displays Yes when the filter is in effect or No when it is not.
Fwd: Shows whether the filter forwards (Yes) a packet or discards (No) it when there’s a match.
Filtering example #1
Returning to our filtering rule example from above (see page 14-7), look at how a rule is translated into a filter.
Start with the rule, then fill in the filter’s attributes:
1. The rule you want to implement as a filter is:
Block all Telnet attempts that originate from the remote host 199.211.211.17.
2. The host 199.211.211.17 is the source of the Telnet packets you want to block, while the destination
address is any IP address. How these IP addresses are masked determines what the final match will be,
although the mask is not displayed in the table that displays the filter sets (you set it when you create the
filter). In fact, since the mask for the destination IP address is 0.0.0.0, the address for Dest IP Addr could
have been anything. The mask for Source IP Addr must be 255.255.255.255 since an exact match is
desired.
■
■
■
■
Source IP Addr = 199.211.211.17
Dest IP Addr = 0.0.0.0
Destination IP address mask = 0.0.0.0
Note: To learn about IP addresses and masks, see Appendix C, “Understanding IP Addressing.”
3. Using the tables on page 14-8, find the destination port and protocol numbers (the local Telnet port):
■
■
Proto = TCP (or 6)
D. Port = 23
4. The filter should be enabled and instructed to block the Telnet packets containing the source address
shown in step 2:
■
■
On? = Yes
Fwd = No
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-11
This four-step process is how we produced the following filter from the original rule:
+-#---Source IP Addr---Dest IP Addr-----Proto-Src.Port-D.Port--On?-Fwd-+
+----------------------------------------------------------------------+
| 1 192.211.211.17 0.0.0.0 TCP 0 23 Yes No |
|
|
+----------------------------------------------------------------------+
Filtering example #2
Suppose a filter is configured to block all incoming IP packets with the source IP address of 200.233.14.0,
regardless of the type of connection or its destination. The filter would look like this:
+-#---Source IP Addr---Dest IP Addr-----Proto-Src.Port-D.Port--On?-Fwd-+
+----------------------------------------------------------------------+
| 1 200.233.14.0
0.0.0.0
0
Yes No |
|
+----------------------------------------------------------------------+
|
This filter blocks any packets coming from a remote network with the IP network address 200.233.14.0. The 0
at the end of the address signifies any host on the class C IP network 200.233.14.0. If, for example, the filter
is applied to a packet with the source IP address 200.233.14.5, it will block it.
In this case, the mask, which does not appear in the table, must be set to 255.255.255.0. This way, all
packets with a source address of 200.233.14.x will be matched correctly, no matter what the final address byte
is.
Note: The protocol attribute for this filter is 0 by default. This tells the filter to ignore the IP protocol or type of
IP packet.
Design guidelines
Careful thought should go into designing a new filter set. You should consider the following guidelines:
■
Be sure the filter set’s overall purpose is clear from the beginning. A vague purpose can lead to a faulty
set, and that can actually make your network less secure.
■
■
Be sure each individual filter’s purpose is clear.
Determine how filter priority will affect the set’s actions. Test the set (on paper) by determining how the
filters would respond to a number of different hypothetical packets.
■
Consider the combined effect of the filters. If every filter in a set fails to match on a particular packet, the
packet is:
■
■
■
passed if all the filters are configured to discard (not forward).
discarded if all the filters are configured to pass (forward).
discarded if the set contains a combination of pass and discard filters.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-12 User’s Reference Guide
Disadvantages of filters
Although using filter sets can greatly enhance network security, there are disadvantages:
■
■
■
Filters are complex. Combining them in filter sets introduces subtle interactions, increasing the likelihood
of implementation errors.
Enabling a large number of filters can have a negative impact on performance. Processing of packets will
take longer if they have to go through many checkpoints.
Too much reliance on packet filters can cause too little reliance on other security methods. Filter sets are
not a substitute for password protection, effective safeguarding of passwords, caller ID, the “must match”
option in the answer profile, PAP or CHAP in connection profiles, callback, and general awareness of how
your network may be vulnerable.
An approach to using filters
The ultimate goal of network security is to prevent unauthorized access to the network without compromising
authorized access. Using filter sets is part of reaching that goal.
Each filter set you design will be based on one of the following approaches:
■
■
That which is not expressly prohibited is permitted.
That which is not expressly permitted is prohibited.
It is strongly recommended that you take the latter, and safer, approach to all of your filter set designs.
Working with IP filters and filter sets
This section covers IP filters and filter sets. For working with IPX filters and filter sets, see “IPX filters” on
page 14-22.
Configuration
Menu
Filter
Sets
IP Filter Sets
To work with filters and filter sets, begin by accessing the filter set screens.
Note: Make sure you understand how filters work before attempting to use them. Read the section “About
filters and filter sets,” beginning on page 14-4.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-13
IP Filter Sets
Display/Change IP Filter Set...
Add IP Filter Set...
Delete IP Filter Set...
Return/Enter to configure and add a new Filter Set
Set Up IP Filter Sets (Firewalls) from this and the following Menus.
The procedure for creating and maintaining filter sets is as follows:
1. Add a new filter set.
2. Create the filters for the new filter set.
3. View, change, or delete individual filters and filter sets.
The sections below explain how to execute these steps.
Adding a filter set
You can create up to eight different custom filter sets. Each filter set can contain up to 16 output filters and up
to 16 input filters.
To add a new filter set, select Add IP Filter Set in the IP Filter Sets screen and press Return to go to the Add
Filter Set screen.
Note: There are two groups of items in the Add Filter Set screen, one for input filters and one for output filters.
The two groups work in essentially the same way, as you’ll see below.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-14 User’s Reference Guide
Add IP Filter Set
Filter Set 2
Filter Set Name:
Display/Change Input Filter...
Add Input Filter...
Delete Input Filter...
Display/Change Output Filter...
Add Output Filter...
Delete Output Filter...
ADD FILTER SET
CANCEL
Configure the Filter Set name and its associated Filters.
Naming a new filter set
All new filter sets have a default name. The first filter set you add will be called Filter Set 1, the next filter will be
Filter Set 2, and so on.
To give a new filter set a different name, select Filter Set Name and enter a new name for the filter set.
To save the filter set, select ADD FILTER SET. The saved filter set is empty (contains no filters), but you can
return to it later to add filters (see “Modifying filter sets” on page 14-18). Or you can add filters to your new set
before saving it (see “Adding filters to a filter set” on page 14-15).
Select CANCEL to leave the Add Filter Set screen without saving the new filter set and return to the Filter Sets
screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-15
Input and output filters—source and destination
There are two kinds of filters you can add to a filter set: input and output. Input filters check packets received
from the Internet, destined for your network. Output filters check packets transmitted from your network to the
Internet.
packet
input filter
LAN
WAN
packet
output filter
The Netopia R-series Router
Packets in the Netopia R2121 pass through an input filter if they originate in the WAN and through an output filter if they’re
being sent out to the WAN.
The process for adding input and output filters is exactly the same. The main difference between the two
involves their reference to source and destination. From the perspective of an input filter, your local network is
the destination of the packets it checks, and the remote network is their source. From the perspective of an
output filter, your local network is the source of the packets, and the remote network is their destination.
Type of filter
“source” means
“destination” means
Input filter
the remote network
the local network
the local network
Output filter
the remote network
Adding filters to a filter set
In this section you’ll learn how to add an input filter to a filter set. Adding an output filter works exactly the same
way, providing you keep the different source and destination perspectives in mind.
To add an input filter, select Add Input Filter in the Add IP Filter Set screen and go to the Add Filter screen.
(Select Add Output Filter to add an output filter.)
Download from Www.Somanuals.com. All Manuals Search And Download.
14-16 User’s Reference Guide
Add Filter
Enabled:
Forward:
No
No
Source IP Address:
Source IP Address Mask:
0.0.0.0
0.0.0.0
Dest. IP Address:
Dest. IP Address Mask:
0.0.0.0
0.0.0.0
Protocol Type:
0
Source Port Compare...
Source Port ID:
Dest. Port Compare...
Dest. Port ID:
No Compare
0
No Compare
0
ADD THIS FILTER NOW
CANCEL
Enter the IP specific information for this filter.
1. To make the filter active in the filter set, select Enabled and toggle it to Yes. If Enabled is toggled to No, the
filter can still exist in the filter set, but it will have no effect.
2. If you want the filter to forward packets that match its criteria to the destination IP address, select Forward
and toggle it to Yes. If Forward is toggled to No, packets matching the filter’s criteria will be discarded.
3. Select Source IP Address and enter the source IP address this filter will match on. You can enter a subnet
or a host address.
4. Select Source IP Address Mask and enter a mask for the source IP address. This allows you to further
modify the way the filter will match on the source address. Enter 0.0.0.0 to force the filter to match on all
source IP addresses, or enter 255.255.255.255 to match the source IP address exclusively.
5. Select Dest. IP Address and enter the destination IP address this filter will match on. You can enter a
6. Select Dest. IP Address Mask and enter a mask for the destination IP address. This allows you to further
modify the way the filter will match on the destination address. Enter 0.0.0.0 to force the filter to match on
all destination IP addresses.
7. Select Protocol Type and enter ICMP, TCP, UDP, Any, or the number of another IP transport protocol (see
Note: If Protocol Type is set to TCP or UDP, the settings for port comparison that you configure in steps 8
and 9 will appear. These settings only take effect if the Protocol Type is TCP or UDP.
8. Select Source Port Compare and choose a comparison method for the filter to use on a packet’s source
port number. Then select Source Port ID and enter the actual source port number to match on (see the
table on page 14-8).
9. Select Dest. Port Compare and choose a comparison method for the filter to use on a packet’s destination
port number. Then select Dest. Port ID and enter the actual destination port number to match on (see the
table on page 14-8).
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-17
10. When you are finished configuring the filter, select ADD THIS FILTER NOW to save the filter in the filter set.
Select CANCEL to discard the filter.
Viewing filters
To display a view-only table of input (output) filters, select Display/ Change Input Filters (Display/ Change
Output Filters) in the Add IP Filter Set screen.
Modifying filters
To modify a filter, select Display/ Change Input Filter (Display/ Change Output Filter) in the Add IP Filter Set
screen to display a table of filters.
Select a filter from the table and press Return to go to the Change Filter screen. The parameters in this screen
are the same as the ones in the Add Filter screen (see “Adding filters to a filter set” on page 14-15).
Change Filter
Enabled:
Forward:
No
No
Source IP Address:
Source IP Address Mask:
0.0.0.0
0.0.0.0
Dest. IP Address:
Dest. IP Address Mask:
0.0.0.0
0.0.0.0
Protocol Type:
0
Source Port Compare...
Source Port ID:
Dest. Port Compare...
Dest. Port ID:
No Compare
0
No Compare
0
Enter the IP specific information for this filter.
Deleting filters
To delete a filter, select Delete Input Filter (Delete Output Filter) in the Add Filter Set screen to display a table
of filters.
Select the filter from the table and press Return to delete it. Press the Escape key to exit the table without
deleting the filter.
Viewing filter sets
To display a view-only list of filter sets, select Display/ Change Filter Sets in the IP Filter Sets screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-18 User’s Reference Guide
Modifying filter sets
To modify a filter set, select Display/ Change Filter Set in the Filter Sets screen to display a list of filter sets.
Select a filter set from the list and press Return to go to the Change IP Filter Set screen. The items in this
screen are the same as the ones in the Add Filter screen (see “Adding filters to a filter set” on page 14-15).
Change IP Filter Set
Filter Set Name:
Basic Firewall
Display/Change Input Filter...
Add Input Filter...
Delete Input Filter...
Display/Change Output Filter...
Add Output Filter...
Delete Output Filter...
Deleting a filter set
Note: If you delete a filter set, all of the filters it contains are deleted as well. To reuse any of these filters in
another set, you’ll have to note their configuration before deleting the current filter set and then recreate them.
To delete a filter set, select Delete Filter Set in the IP Filter Sets screen to display a list of filter sets.
Select a filter set from the list and press Return to delete it. Press the Escape key to exit the list without
deleting the filter set.
A sample IP filter set
This section contains the settings for a filter set, called Basic Firewall, which is part of the Netopia R2121’s
factory configuration.
Basic Firewall blocks undesirable traffic originating from the WAN (in most cases, the Internet), but passes all
traffic originating from the LAN. It follows the conservative “that which is not expressly permitted is prohibited”
approach: unless an incoming packet expressly matches one of the constituent input filters, it will not be
forwarded to the LAN.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-19
The five input filters and one output filter that make up Basic Firewall are shown in the table below.
Output filter
1
Setting
Input filter 1
Input filter 2
Input filter 3
Input filter 4
Input filter 5
Enabled
Forward
Yes
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Source IP
address
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
Source IP
address mask
0.0.0.0
0.0.0.0
0.0.0.0
TCP
0.0.0.0
0.0.0.0
0.0.0.0
TCP
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
TCP
0.0.0.0
0.0.0.0
0.0.0.0
UDP
0.0.0.0
0.0.0.0
0.0.0.0
Dest. IP
address
Dest. IP
address mask
Protocol type
ICMP
N/ A
0
Source port
comparison
No Com-
pare
No Com-
pare
No Com-
pare
No Com-
pare
N/ A
Source port ID
0
0
N/ A
N/ A
0
0
N/ A
N/ A
Dest. port
comparison
Equal
Equal
Greater
Than
Greater
Than
Dest. port ID
2000
6000
N/ A
1023
1023
N/ A
Basic Firewall’s filters play the following roles.
Input filters 1 and 2: These block WAN-originated OpenWindows and X-Windows sessions. Service origination
requests for these protocols use ports 2000 and 6000, respectively. Since these are greater than 1023,
OpenWindows and X-Windows traffic would otherwise be allowed by input filter 4. Input filters 1 and 2 must
precede input filter 4; otherwise they would have no effect as filter 4 would have already passed OpenWindows
and X-Windows traffic.
Input filter 3: This filter explicitly passes all WAN-originated ICMP traffic to permit devices on the WAN to ping
devices on the LAN. Ping is an Internet service that is useful for diagnostic purposes.
Input filters 4 and 5: These filters pass all TCP and UDP traffic, respectively, when the destination port is
greater than 1023. This type of traffic generally does not allow a remote host to connect to the LAN using one
of the potentially intrusive Internet services, such as Telnet, FTP, and WWW.
Output filter 1: This filter passes all outgoing traffic to make sure that no outgoing connections from the LAN
are blocked.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-20 User’s Reference Guide
Basic Firewall is suitable for a LAN containing only client hosts that wish to access servers on the WAN, not for
a LAN containing servers providing services to clients on the WAN. Basic Firewall’s general strategy is to
explicitly pass WAN-originated TCP and UDP traffic to ports greater than 1023. Ports lower than 1024 are the
service origination ports for various Internet services such as FTP, Telnet, and the World Wide Web (WWW).
A more complicated filter set would be required to provide WAN access to a LAN-based server. See “Possible
modifications,” below, for ways to allow remote hosts to use services provided by servers on the LAN.
Possible modifications
You can modify the sample filter set Basic Firewall to allow incoming traffic using the examples below. These
modifications are not intended to be combined. Each modification is to be the only one used with Basic Firewall.
The results of combining filter set modifications can be difficult to predict. It is recommended that you take
special care if making more than one modification to the sample filter set.
Trusted host. To allow unlimited access by a trusted remote host with the IP address a.b.c.d (corresponding to
a numbered IP address such as 163.176.8.243), insert the following input filter ahead of the current input filter
1:
■
■
■
■
■
■
■
Enabled: Yes
Forward: Yes
Source IP Address: a.b.c.d
Source IP Address Mask: 255.255.255.255
Dest. IP Address: 0.0.0.0
Dest. IP Address Mask: 0.0.0.0
Protocol Type: 0
Trusted subnet. To allow unlimited access by a trusted remote subnet with subnet address a.b.c.d
(corresponding to a numbered IP address such as 163.176.8.0) and subnet mask e.f.g.h (corresponding to a
numbered IP mask such as 255.255.255.0), insert the following input filter ahead of the current input filter 1:
■
■
■
■
■
■
■
Enabled: Yes
Forward: Yes
Source IP Address: a.b.c.d
Source IP Address Mask: e.f.g.h
Dest. IP Address: 0.0.0.0
Dest. IP Address Mask: 0.0.0.0
Protocol Type: 0
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-21
FTP sessions. To allow WAN-originated FTP sessions to a LAN-based FTP server with the IP address a.b.c.d
(corresponding to a numbered IP address such as 163.176.8.243), insert the following input filter ahead of the
current input filter 1:
■
■
■
■
■
■
■
■
■
■
■
Enabled: Yes
Forward: Yes
Source IP Address: 0.0.0.0
Source IP Address Mask: 0.0.0.0
Dest. IP Address: a.b.c.d
Dest. IP Address Mask: 255.255.255.255
Protocol Type: TCP
Source Port Comparison: No Compare
Source Port ID: 0
Dest. Port Comparison: Equal
Dest. Port ID: 21
Note: A similar filter could be used to permit Telnet or WWW access. Set the Dest. Port ID to 23 for Telnet or
80 for WWW.
AURP tunnel. To allow an AURP tunnel between a remote AURP router with the IP address a.b.c.d
(corresponding to a numbered IP address such as 163.176.8.243) and a local AURP router (including the
Netopia R2121 itself), insert the following input filter ahead of the current input filter 1:
■
■
■
■
■
■
■
■
■
■
■
Enabled: Yes
Forward: Yes
Source IP Address: a.b.c.d
Source IP Address Mask: 255.255.255.255
Dest. IP Address: 0.0.0.0
Dest. IP Address Mask: 0.0.0.0
Protocol Type: UDP
Source Port Comparison: Equal
Source Port ID: 387
Dest. Port Comparison: Equal
Dest. Port ID: 387
Download from Www.Somanuals.com. All Manuals Search And Download.
14-22 User’s Reference Guide
IPX filters
Filter Sets
(Firewalls)
IPX Filters
and Filter Sets
System
Configuration
Main
Menu
IPX packet filters work very similarly to IP packet filters. They filter data traffic coming from or going to remote
IPX networks. IPX filters can be set up to pass or discard IPX packets based on a number of user-defined
criteria. Like IP filters, IPX filters must be grouped in sets that are applied to the answer profile or to connection
profiles.
IPX SAP filters are used for filtering server entries not required to pass over the WAN links. When connecting to
a large IPX network via dial-up connection, the transfer of large numbers of SAP entries can consume significant
bandwidth on the WAN link.
Note: Using SAP filtering to prevent a server from being advertised does not provide security against that
server being accessed—IPX packet filtering must be used for that purpose.
Setting up and using IPX filter sets is a four-step process:
1. Create the filters to use.
2. Create the filter sets to use.
3. Add filters to the filter sets.
4. Attach the filter sets to the answer profile or to connection profiles.
You can configure IPX filters and set up IPX filter sets from the IPX Filters and Filter Sets screen.
IPX Filters and Filter Sets
Display/Change IPX Packet Filters...
Add IPX Packet Filter...
Delete IPX Packet Filter...
Display/Change IPX Packet Filter Sets...
Add IPX Packet Filter Set...
Delete IPX Packet Filter Set...
Display/Change IPX Sap Filters...
Add IPX Sap Filter...
Delete IPX Sap Filter...
Display/Change IPX Sap Filter Sets...
Add IPX Sap Filter Set...
Delete IPX Sap Filter Set...
Define your filters 1st. IPX Filter Sets refer to, but don't contain, filters.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-23
The items in the IPX Filters and Filter Sets screen are grouped into four areas:
■
■
■
■
IPX packet filters
IPX packet filter sets
IPX SAP filters
IPX SAP filter sets
The following sections explain the items in each of these areas.
IPX packet filters
For each IPX packet filter, you can configure a set of parameters to match on the source or destination
attributes of IPX data packets coming from or going to the WAN.
Viewing and modifying packet filters
To display a view-only table of IPX packet filters, select Show/ Change IPX Packet Filters in the IPX Filters and
Filter Sets screen.
To modify any of the filters in the table, note the desired filter and press Return to go to the Change Packet Filter
screen. The parameters in this screen are the same as the ones in the Add Packet Filter screen (see the next
section).
Adding a packet filter
To add a new IPX packet filter, select Add IPX Packet Filter in the IPX Filters and Filter Sets screen and press
Return to go to the Add Packet Filter screen.
Add Packet Filter
Filter Name:
IPX Filter 1
Source Network:
Source Node Address:
Source Socket:
00000000
000000000000
0000
Destination Network:
Destination Node Address:
Destination Socket:
00000000
000000000000
0000
ADD FILTER NOW
CANCEL
Configure a new IPX Packet Filter. Finished? ADD or CANCEL to exit.
By default, the filter’s socket numbers and network and node addresses are null (all zeros). This sets the filter
to match on any IPX data packet. You should configure the filter using criteria that meet your security needs.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-24 User’s Reference Guide
1. Select Filter Name and enter a descriptive name for the filter.
2. To specify a source network for the filter to match on, select Source Network and enter an IPX network
address.
3. To specify a source node for the filter to match on, select Source Node Address and enter an IPX node
address.
4. To specify a source socket for the filter to match on, select Source Socket and enter an IPX source socket
number.
5. To specify a destination network for the filter to match on, select Destination Network and enter an IPX
network address.
6. To specify a destination node for the filter to match on, select Destination Node Address and enter an IPX
node address.
7. To specify a destination socket for the filter to match on, select Destination Socket and enter an IPX
destination socket number.
8. Select ADD FILTER NOW to save the current filter. Select CANCEL to exit the Add Packet Filter screen
without saving the new filter.
Deleting a packet filter
To delete a packet filter, select Delete IPX Packet Filter in the IPX Filters and Filter Sets screen to display a
table of filters. Select a filter from the table and press Return to delete it. Press the Escape key to exit the table
without deleting the filter.
IPX packet filter sets
Before the individual filters can be used, IPX packet filters must be grouped into sets. A filter can be part of
more than one filter set.
Viewing and modifying packet filter sets
To display a table of IPX packet filter sets, select Show/ Change IPX Packet Filter Sets in the IPX Filters and
Filter Sets screen.
To modify any of the filter sets in the list, select the desired filter set and press Return to go to the Change
Packet Filter Set screen. The parameters in this screen are the same as the ones in the Add Packet Filter Set
screen (see the next section).
Adding a packet filter set
To add a new IPX packet filter set, select Add IPX Packet Filter Set in the IPX Filters and Filter Sets screen and
press Return to go to the Add Packet Filter Set screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-25
Add Packet Filter Set
Filter Set Name:
Show Filters/Change Action on Match...
Append Filter...
Remove Filter...
ADD FILTER SET NOW
CANCEL
Configure an IPX Filter Set here. You must ADD FILTER SET NOW to save.
Follow these steps to configure the new packet filter set:
1. Select Filter Set Name and enter a descriptive name for the filter set.
2. To change the forwarding action of filters in the filter set, select Show Filters/ Change Action on Match
and press Return to go to the Show Filters/ Change Actions on Match screen.
Show Filters/Change Actions on Match
Filter Name---------------------Forward
Filter 1
No
Filter 2
No
<<NO MATCH>>
Yes
Set whether filters forward or drop matching packets here.
Select a filter and toggle the packet forwarding action to Yes (pass) or No (discard).
Download from Www.Somanuals.com. All Manuals Search And Download.
14-26 User’s Reference Guide
3. To add a filter to the filter set, select Append Filter to display a table of filters. Select a filter from the table
and press Return to add it to the filter set. The default action of newly added filters is to not forward
packets that match their criteria.
To exit the table without adding the filter, press the Escape key.
4. To remove a filter from the filter set, select Detach Filter to display a table of appended filters. Select a
filter from the table and press Return to remove it from the set. To exit the table without removing the filter,
press the Escape key.
5. Select ADD FILTER SET NOW to save the current filter set. Select CANCEL to exit the Add Packet Filter Set
screen without saving the new filter set.
Deleting a packet filter set
To delete a packet filter set, select Delete IPX Packet Filter Set in the IPX Filters and Filter Sets screen to
display a list of filter sets. Select a filter set from the list and press Return to delete it. Press the Escape key to
exit the list without deleting the filter set.
Note: Deleting a filter set does not delete the filters in that set. However, the filters in the deleted set are no
longer in effect (unless they are part of another set). The deleted set will no longer appear in the answer profile
or any connection profiles to which it was added.
IPX SAP filters
For each IPX SAP filter, you can configure a set of parameters to match on certain attributes of IPX SAP packet
entries. The filters check IPX SAP packets for entries that match and then act on those entries. The SAP
packets themselves are always allowed to continue after their entries are checked.
The purpose of filtering SAP packets is not to make your network more secure, but to add efficiency to network
bandwidth use. Filtering SAP packets may reduce the size of SAP packets and SAP bindery tables by removing
unwanted entries.
Viewing and modifying SAP filters
To display a table of IPX SAP filters, select Show/ Change IPX SAP Filters in the IPX Filters and Filter Sets
screen.
To modify any of the filters in the table, select the desired filter and press Return to go to the Change SAP Filter
screen. The parameters in this screen are the same as the ones in the Add SAP Filter screen (see the next
section).
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-27
Adding a SAP filter
To add a new IPX SAP filter, select Add IPX SAP Filter in the IPX Filters and Filter Sets screen and press Return
to go to the Add SAP Filter screen.
Add Sap Filter
Filter Name:
Server Name:
Socket:
Type:
0000
0000
IPX Network:
IPX Node Address:
00000000
000000000000
ADD FILTER NOW
CANCEL
Configure a new IPX SAP Filter. Finished? ADD or CANCEL to exit.
By default, the filter’s socket and type numbers and network and node addresses are null (all zeros). This sets
the filter to match on any IPX SAP packet entry. You should configure the filter using criteria that meet your
needs.
Follow these steps to configure the new SAP filter:
1. Select Filter Name and enter a descriptive name for the filter.
2. To specify a server name for the filter to match on, select Server Name and enter the name of an IPX
server. You can use the wildcard characters * (asterisk) and ? (question mark). Use * to match any string,
including a null string (no characters), and ? to match any single character in the server’s name. For
example, the filter could match on the server name “NETOPIA” with “NETO*”, “NETO?IA”, and “NETOPIA*”.
3. To specify a socket for the filter to match on, select Socket and enter an IPX socket number.
4. To specify a type number for the filter to match on, select Type and enter an IPX type number.
5. To specify an IPX network address for the filter to match on, select IPX Network and enter an IPX network
address.
6. To specify an IPX node address for the filter to match on, select IPX Node Address and enter an IPX node
address.
7. Select ADD FILTER NOW to save the current filter. Select CANCEL to exit the Add SAP Filter screen without
saving the new filter.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-28 User’s Reference Guide
Deleting a SAP filter
To delete a SAP filter, select Delete IPX SAP filter in the IPX Filters and Filter Sets screen to display a table of
filters. Select a filter from the table and press Return to delete it. Press the Escape key to exit the table without
deleting the filter.
IPX SAP filter sets
Before IPX SAP filters can be used, they must be grouped into sets. A SAP filter can be part of more than one
filter set.
Viewing and modifying SAP filter sets
To display a table of IPX SAP filter sets, select Show/ Change IPX SAP Filter Sets in the IPX Filters and Filter
Sets screen to display a list of filter sets.
To modify any of the filter sets in the list, select the desired filter set and go to the Change SAP Filter Set
screen. The parameters in this screen are the same as the ones in the Add SAP Filter Set screen (see the
previous section).
Adding a SAP filter set
To add a new IPX SAP filter set, select Add IPX SAP Filter Set in the IPX Filters and Filter Sets screen and go to
the Add SAP Filter Set screen.
Add SAP Filter Set
Filter Set Name:
Show Filters/Change Action on Match...
Append Filter...
Remove Filter...
ADD FILTER SET NOW
CANCEL
Configure an IPX Filter Set here. You must ADD FILTER SET NOW to save.
Follow these steps to configure the new SAP filter set:
1. Select Filter Set Name and enter a descriptive name for the filter set.
2. To change the forwarding action of filters in the filter set, select Show Filters/ Change Action on Match
and press Return to go to the Show Filters/ Change Actions on Match screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-29
Show Filters/Change Actions on Match
Filter Name---------------------Forward
Filter 1
No
Filter 2
No
<<NO MATCH>>
Yes
Set whether filters forward or drop matching packets here.
Select a filter and toggle the entry forwarding action to Yes (pass) or No (discard).
3. To add a filter to the filter set, select Append Filter to display a table of filters. Select a filter from the table
and press Return to add it to the filter set. The default action of newly added filters is to not forward
(discard) packet entries that match their criteria.
To exit the table without adding the filter, press the Escape key.
4. To remove a filter from the filter set, select Detach Filter to display a table of appended filters. Select a
filter from the table and press Return to remove it from the set. To exit the table without removing the filter,
press the Escape key.
5. Select ADD FILTER SET NOW to save the current filter set. Select CANCEL to exit the Add SAP Filter Set
screen without saving the new filter set.
Deleting a SAP filter set
To delete a SAP filter set, select Delete IPX SAP Filter Set in the IPX Filters and Filter Sets screen to display a
list of filter sets. Select a filter set from the list and press Return to delete it. Press the Escape key to exit the
list without deleting the filter set.
Note: Deleting a filter set does not delete the filters in that set. However, the filters in the deleted set are no
longer in effect (unless they are part of another set). The deleted set will no longer appear in the answer profile
or any connection profiles to which it was added.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-30 User’s Reference Guide
Firewall tutorial
General Firewall Terms
Firewall: a component or set of components that restrict access between a protected network and the Internet,
or between two networks.
Host: A workstation on the Network.
Packet: Unit of communication on the Internet.
Packet Filter: Packet filters allow or deny packets based on source or destination IP addresses, TCP or UDP
ports, or the TCP ACK bit.
Port: A number that defines a particular type of service.
Filter Rule: A filter set is comprised of individual filter rules.
Filter Set: A grouping of individual filter rules.
Basic IP Packet Components
All IP packets contain the same basic “header” information, as follows:
Source IP Address
Destination IP Address
Source Port
Destination Port
Protocol
163.176.132.18
163.176.4.27
2541
80
TCP
ACK Bit
Yes
DATA
User Data
This header information is what the packet filter uses to make filtering decisions. It is important to note that a
packet filter does not look into the IP datastream (the User Data from above) to make filtering decisions.
Basic Protocol Types
TCP: Transmission Control Protocol. TCP provides reliable packet delivery and has a retransmission
mechanism (so packets are not lost). RFC 793 is the specification for TCP.
UDP: User Datagram Protocol. Unlike TCP, UDP does not guarantee reliable, sequenced packet delivery. If data
does not reach its destination, UDP does not re transmit the data. RFC 768 is the specification for UDP.
And there are many more ports defined in the Assigned Addresses RFC.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-31
Example TCP/UDP Ports
TCP Port
Service
FTP
UDP Port
161
Service
SNMP
20/ 21
23
Telnet
SMTP
WWW
News
69
TFTP
25
387
AURP
80
144
Firewall design rules
There are two basic rules to firewall design:
■
“What is not explicitly allowed is denied...”
and
■
“What is not explicitly denied is allowed...”
The first rule is far more secure, and is the best approach to firewall design. It is far easier (and more secure)
to allow in or out only certain services and deny anything else. If the other rule is used, you would have to figure
out everything that you want to disallow, now and future.
Firewall Logic
Firewall design is a test of logic, and filter rule ordering is critical. If a packet is passed through a series of filter
rules and then the packet matches a rule, the appropriate action is taken. The packet will not pass through the
remainder of the filter rules.
For example, if you had the following filter set...
Allow WWW access;
Allow FTP access;
Allow SMTP access;
Deny all other packets.
and a packet goes through these rules destined for FTP, the packet would pass through the first rule (WWW), go
through the second rule (FTP), matches this rule and the packet is allowed through.
If you had this filter set for example....
Allow WWW access;
Allow FTP access;
Deny FTP access;
Deny all other packets.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-32 User’s Reference Guide
and a packet goes through these rules destined for FTP, the packet would pass through the first filter rule
(WWW), match the second rule (FTP) and the packet is allowed through. Even though the next rule is to deny all
FTP traffic, the FTP packet will never make it to this rule.
Binary Representation
It is easiest when doing filtering to convert the IP address and mask in question to binary. This will allow you to
perform the logical AND to determine if a packet matches a filter rule.
Logical ANDing
When a packet is compared (in most cases) a logical AND is performed. First the IP addresses and subnet
masks are converted to binary and then ANDed together. The rules for logical ANDing are as follows:
0 AND 0 = 0
0 AND 1 = 0
1 AND 0 = 0
1 AND 1 = 1
For example:
Filter rule:
Deny
IP: 163.176.1.15
Mask: 255.255.255.255 BINARY: 11111111.11111111.11111111.11111111
Incoming Packet:
IP 163.176.1.15
AND the incoming packet and subnet mask together, the result is:
10100011.10110000.00000001.00001111
BINARY: 10100011.10110000.00000001.00001111
BINARY: 10100011.10110000.00000001.00001111
which matches the IP address in the filter rule and the packet is denied.
Implied Rules
With a given set of filter rules, there is an Implied rule which may or may not be shown to the user. The implied
rule tells the filter set what to do with a packet that does not match any of the filter rules. An example of implied
rules is as follows:
Implied
Meaning
Y+Y+Y=N
N+N+N=Y
Y+N+Y=N
If all filter rules are YES, the implied is NO.
If all filter rules are NO, the implied is YES.
If a mix of YES and NO filters, the implied is NO.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-33
Established Connections
The TCP header contains one bit called the ACK Bit (or TCP Ack bit). This ACK Bit only appears with TCP, not
UDP. The ACK bit is part of the TCP mechanism that guaranteed the delivery of data. The ACK bit is set
whenever one side of a connection has received data from the other side. Only the first TCP packet will not have
the ACK bit set, once the TCP connection is in place the remainder of the TCP packets with have the ACK bit
set.
The ACK bit is helpful for firewall design and reduces the number of potential filter rules. A filter rule could be
created just allowing incoming TCP packets with the ACK bit set, as these packets had to be originated from the
local network.
Example IP Filter Set Screen
This is an example of the Netopia IP filter set screen:
Change Filter
Enabled:
Forward:
Yes
No
Source IP Address:
Source IP Address Mask:
0.0.0.0
0.0.0.0
Dest. IP Address:
Dest. IP Address Mask:
0.0.0.0
0.0.0.0
Protocol Type:
TCP
Source Port Compare...
Source Port ID:
Dest. Port Compare...
Dest. Port ID:
Established TCP Conns. Only:
No Compare
0
Equal
2000
No
Return/Enter accepts * Tab toggles * ESC cancels.
Enter the IP specific information for this filter.
Filter Basics
In the source or destination IP address fields, the IP address that is entered MUST be the NETWORK address of
the subnet. A HOST address can be entered, but the applied subnet mask must be 32 bits (255.255.255.255).
The Netopia R2121 has the ability to compare source and destination TCP or UDP ports. These options are as
follows:
Item
No compare
What it means
Does not compare TCP or UDP port
Matches any port other than what is defined
Anything less than the port defined
Not Equal To
Less Than
Download from Www.Somanuals.com. All Manuals Search And Download.
14-34 User’s Reference Guide
Less Than Or Equal
Equal
Any port less than or equal to the port defined
Matches only the port defined
Greater Than or Equal Matches the port or any port greater
Greater Than Matches anything greater than the port defined.
Example Network
Incoming
Packet Filter
Netopia
Internet
DATA
IP: 200.1.1.??
Example Filters
Example 1
Filter Rule:
200.1.1.0
(Source IP Network Address)
(Source IP Mask)
255.255.255.128
Forward = No
(What happens on match)
Incoming packet has the source address of 200.1.1.28
IP Address
200.1.1.28
AND
Binary Representation
00011100
(Source address in incoming IP packet)
255.255.255.128 10000000
00000000
(Perform the logical AND)
(Logical AND result)
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-35
This incoming IP packet has a source IP address that matches the network address in the Source IP Address
field (00000000) in the Netopia R2121. This will NOT forward this packet.
Example 2
Filter Rule:
200.1.1.0
(Source IP Network Address)
(Source IP Mask)
255.255.255.128
Forward = No
(What happens on match)
Incoming packet has the source address of 200.1.1.184
IP Address
200.1.1.184
AND
Binary Representation
10111000
(Source address in incoming IP packet)
255.255.255.128 10000000
10000000
(Perform the logical AND)
(Logical AND result)
This incoming IP packet (10000000) has a source IP address that does not match the network address in the
Source IP Address field (00000000) in the Netopia R2121. This rule WILL forward this packet because the
packet does not match.
Example 3
Filter Rule:
200.1.1.96
(Source IP Network Address)
(Source IP Mask)
255.255.255.240
Forward = No
(What happens on match)
Incoming packet has the source address of 200.1.1.184
IP Address
200.1.1.184
AND
Binary Representation
10111000
(Source address in incoming IP packet)
255.255.255.240 11110000
10110000
(Perform the logical AND)
(Logical AND result)
Download from Www.Somanuals.com. All Manuals Search And Download.
14-36 User’s Reference Guide
Since the Source IP Network Address in the Netopia R2121 is 01100000, and the source IP address after the
logical AND is 1011000, this rule does NOT match and this packet will be passed.
Example 4
Filter Rule:
200.1.1.96
(Source IP Network Address)
(Source IP Mask)
255.255.255.240
Forward = No
(What happens on match)
Incoming packet has the source address of 200.1.1.104
IP Address
200.1.1.104
AND
Binary Representation
01101000
(Source address in incoming IP packet)
255.255.255.240 11110000
01100000
(Perform the logical AND)
(Logical AND result)
Since the Source IP Network Address in the Netopia R2121 is 01100000, and the source IP address after the
logical AND is 01100000, this rule DOES match and this packet will NOT be passed.
Example 5
Filter Rule:
200.1.1.96
(Source IP Network Address)
(Source IP Mask)
255.255.255.255
Forward = No
(What happens on match)
Incoming packet has the source address of 200.1.1.96
IP Address
200.1.1.96
AND
Binary Representation
01100000
(Source address in incoming IP packet)
255.255.255.255 11111111
01100000
(Perform the logical AND)
(Logical AND result)
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-37
Since the Source IP Network Address in the Netopia R2121 is 01100000, and the source IP address after the
logical AND is 01100000, this rule DOES match and this packet will NOT be passed. This rule masks off a
SINGLE IP address.
Token Security Authentication
This section discusses how to configure and use security authentication on the Netopia R2121.
Note: The security authentication feature only applies to Netopia R2121 models connecting over a dial-up line
using the PPP-PAP-TOKEN or PPP-CACHE-TOKEN authentication protocol.
Securing network environments
Unauthorized tampering or theft of information on internal networks causes serious ramifications, given the
reliance on information systems. Network abuse is a serious problem, complicated by the difficulty in detecting
the source of the abuses. An unauthorized user can gain access to networks and copy information without
leaving a trace.
Password protection is one solution, but static passwords are often insecure. They can be compromised,
allowing unauthorized users to disguise themselves as authorized users and enter supposedly secure systems.
However, a company called Security Dynamics™ has patented a security authentication technology to increase
network security.
SecurID is a two-factor authentication process to protect against unauthorized access. This dynamic user
authentication produces a randomly-generated security code mechanism that changes every 60 seconds. At
login, authorized users enter their password and the code displayed on their SecurID token card. While a
password may be compromised, the constantly changing access code, which requires the token card during
system use, bars unauthorized users from entering the network.
Using the SecurID token card
Each SecurID token card is programmed with an algorithm that ensures every code displayed is valid only for
that user at that particular time. The token card has a display that authorizes the individual user access to the
computer. Through this authentication system, the user’s identity is verified when the correct password and
current code are entered from the user’s token.
Personal identification number (PIN)
The user’s password is called a personal identification number, or PIN. The user enters the secret PIN from a
console connection, followed by the current code displayed on the token card. Then the access control module
must authenticate the token’s unique code in combination with the user’s secret PIN before access is granted.
Key Security Authentication Features of the Netopia R2121
As a remote device, the Netopia R2121 offers client/ calling side security authentication. This feature allows
the Netopia R2121 to call a server router and perform security card authentication. The router of the called
server must have access to a server with ACE software loaded on it.
To perform security card authentication, each user must have a security authentication token card and a PIN. In
addition, the user’s identifying information must reside on the remote ACE servers for authentication
negotiation to properly take place.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-38 User’s Reference Guide
The Netopia R2121 supports the following user configurations for security authentication:
■
■
■
■
Single user, calling a single destination (single session)
Single user, calling multiple destinations (two simultaneous and separate sessions)
Multiple users, calling a single destination (single session)
Multiple users, calling multiple destinations (two simultaneous and separate sessions
Security authentication components
To properly identify and authenticate an authorized user, the following are required:
■
■
■
A secret personal identification number (PIN) for each user.
A security authentication token card.
A Security Access Control Module (ACM).
Note: The Netopia R2121 currently only supports Ascend routers as ACMs.
■
An external Netopia R2121 calling into a designated server. For example, a telecommuter dialing into a
remote site from a Netopia R2121 interested in accessing personal email or file sharing services.
Note: The Netopia R2121 does not include a security authentication token card.
Configuring for security authentication
To configure the Netopia R2121 to support security authentication, select an authentication method and set up
a designated connection profile from the System Configuration screen or your first connection profile from Easy
Setup.
1. From the WAN Configuration menu, select Display/ Change Connection Profile. From the pop-up menu that
appears, select a Connection Profile. In the Connection Profile screen select Datalink Options.
WAN
Configuration
Main
Menu
Display/ Change
Connection Profile
Datalink Options
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-39
Datalink (PPP/MP) Options
Data Compression...
Ascend LZS
PAP-TOKEN
Send Authentication...
Send User Name:
Receive User Name:
Receive Password:
Channel Usage...
Dynamic
Auto
Bandwidth Allocation...
Maximum Packet Size:
1500
In this Screen you will configure the PPP/MP specific connection params.
2. Select Send Authentication and press Return. From the pop-up menu, highlight PAP-TOKEN or
CACHE-TOKEN. Your network administrator or the remote network administrator will tell you which method
to select.
If you select PAP-TOKEN, select Send User Name and enter a name for your Netopia R2121. You will not
need to enter a Send Password for PAP-TOKEN. Press Return.
If you select CACHE-TOKEN, select Send User Name and enter a name for your Netopia R2121. Then,
select Send Password and enter a secret name or number. Press Return.
3. Set up a connection profile to use with your authentication method. For information on setting up a
connection profile, see Chapter 7, “Easy Setup.”
Note: If you are setting up your first connection profile, you can also enter your authentication information in
the Easy Setup Connection Profile screen.
Connecting using security authentication
You can initiate a connection call using security authentication in either of two ways:
■
■
establish a dial-on-demand (DOD) connection, or
establish a manual connection.
Establishing a dial-on-demand (DOD) connection call
To establish a connection call using DOD, select Utilities & Diagnostics from the Main Menu and press Return.
Note: The Secure Authentication Monitor field will remain hidden if PAP-TOKEN or CACHE-TOKEN is not the
selected authentication method in the connection profile.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-40 User’s Reference Guide
Utilities & Diagnostics
Ping...
Trace Route...
Telnet...
Secure Authentication Monitor...
Trivial File Transfer Protocol (TFTP)...
X-Modem File Transfer...
Revert to Factory Defaults...
Restart System...
1. Select Secure Authentication Monitor and press Return. The Secure Authentication Monitor screen
appears.
2. Wait for the call to initiate.
Secure Authentication Monitor
Current Connection Status
Profile Name---State---%Use---Remote Address---Est.---More Info---
Status --- Passcode Required
For Connection Profile: Easy Setup Profile
0-Challenge: Enter PASSCODE:
Passcode:
123412345678
3. From the fields that appear, select Enter PASSCODE and press Return. Enter your PIN and the code
displayed on your security authentication token card LED.
4. Once the call is established, and you enter your passcode as prompted, PPP negotiation will continue. If
the call is specified for PAP-TOKEN, and the session involves more than one connection, you will be
prompted for each connection being brought up.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security 14-41
Note: When using CACHE-TOKEN, your passcode is valid for a time interval determined by the network
administrator. When this time interval expires, you must provide a new passcode for the call negotiation.
When using PAP-TOKEN, your passcode is valid for one call negotiation. For a second call negotiation, you must
enter the next passcode provided by the security authentication token card every 60 seconds.
You will be able to access information at the remote site that you are connecting to once authentication is
successfully completed.
Establishing a manual connection call
To establish a Manual connection call, select WAN Configuration from the Main Menu and press Return.
1. Select Establish WAN Connection from the WAN Configuration screen and press Return. The Establish
WAN Connection screen displays a table of all of the connection profiles you have defined. Highlight the
connection profile you wish to manually call. Press Return to initiate the call.
Call Status
Profile Name -- Easy Setup Profile
Connection State -- Dialing
Channel 1 State -- Acquiring
Channel 2 State --
0-Challenge: Enter PASSCODE:
Passcode:
123412345678
Hit ESCAPE/RETURN/ENTER to return to previous menu.
2. From the fields that appear, select Enter PASSCODE and press Return. Enter your PIN and the code
displayed on your security authentication token card LED screen.
3. Once the call is established, and you enter your passcode as prompted, PPP negotiation will continue. If
the call is specified for PAP-TOKEN, and the session involves more than one connection, you will be
prompted for each channel being brought up.
Note: When using CACHE-TOKEN, your passcode is valid for a time interval determined by the network
administrator. When this time interval expires, you must provide a new passcode for the call negotiation.
When using PAP-TOKEN for a dial-up call, your passcode is valid for one call negotiation. For a second call
negotiation, you must enter the next passcode provided by the security authentication token card every 60
seconds.
You will be able to access information at the remote site that you are connecting to once authentication is
successfully completed.
Download from Www.Somanuals.com. All Manuals Search And Download.
14-42 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Diagnostics 15-1
Chapter 15
■
■
■
■
■
■
■
■
■
“Transferring configuration and firmware files with TFTP” on page 15-7
“Transferring configuration and firmware files with XMODEM” on page 15-10
“Factory defaults” on page 15-7
“Restarting the system” on page 15-13
Note: These utilities and tests are accessible only through the console-based management screens. See
Chapter 6, “Console-based Management,” for information on accessing the console-based management
screens.
You access the Utilities & Diagnostics screens from the Main Menu.
Utilities & Diagnostics
Ping...
Trace Route...
Telnet...
Secure Authentication Monitor...
Disconnect Telnet Console Session...
Trivial File Transfer Protocol (TFTP)...
Revert to Factory Defaults...
Restart System...
Download from Www.Somanuals.com. All Manuals Search And Download.
15-2 User’s Reference Guide
Ping
The Netopia R2121 includes a standard Ping test utility. A Ping test generates IP packets destined for a
particular (Ping-capable) IP host. Each time the target host receives a Ping packet, it returns a packet to the
original sender.
Ping allows you to see whether a particular IP destination is reachable from the Netopia R2121. You can also
ascertain the quality and reliability of the connection to the desired destination by studying the Ping test’s
statistics.
To use the Ping utility, select Ping in the Statistics, Utilities, Tests screen and press Return to go to the Ping
screen.
ICMP Ping
Name of Host to Ping:
Packets to Send:
Data Size:
Delay (seconds):
5
56
1
START PING
Status:
Packets Out:
Packets In:
Packets Lost:
Round Trip Time
(Min/Max/Avg):
0
0
0 (0%)
0.000 / 0.000 / 0.000 secs
Enter the IP Address/Domain Name of a host to ping.
Send ICMP Echo Requests to a network host.
To configure and initiate a Ping test, follow these steps:
1. Select Name of Host to Ping and enter the destination domain name or IP address.
2. Select Packets to Send to change the default setting. This is the total number of packets to be sent during
the Ping test. The default setting is adequate in most cases, but you may change it to any value from 1 to
4,294,967,295.
3. Select Data Size to change the default setting. This is the size, in bytes, of each Ping packet sent. The
default setting is adequate in most cases, but you may change it to any value from 0 (only header data) to
1664.
4. Select Delay (seconds) to change the default setting. The delay, in seconds, determines the time between
Ping packets sent. The default setting is adequate in most cases, but you may change it to any value from
0 to 4,294,967. A delay of 0 seconds forces packets to be sent immediately one after another.
5. Select START PING and press Return to begin the Ping test. While the test is running, the START PING
item becomes STOP PING. To manually stop the Ping test, select STOP PING and press Return or the
Escape key.
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Diagnostics 15-3
While the Ping test is running, and when it is over, a status field and a number of statistical items are active on
the screen. These are described below.
Status: The current status of the Ping test. This item can display the following messages:
Message
Description
Resolving host name
Can’t resolve host name
Pinging
Finding the IP address for the domain name-style address
IP address can’t be found for the domain name-style name
Ping test is in progress
Complete
Ping test was completed
Cancelled by user
Ping test was cancelled manually
Destination unreachable from
w.x.y.z
Ping test was able to reach the router with IP address
w.x.y.z, which reported that the test could not reach the
final destination
Couldn’t allocate packet buffer
Couldn’t open ICMP port
Couldn’t proceed with Ping test; try again or reset system
Couldn’t proceed with Ping test; try again or reset system
Packets Out: The number of packets sent by the Ping test.
Packets In: The number of return packets received from the target host. To be considered “on time,” return
packets are expected back before the next packet in the sequence of Ping packets is sent. A count of the
number of late packets appears in parentheses to the right of the Packets In count.
In the example below, a Netopia R2121 is sending Ping packets to another host, which responds with return
Ping packets. Note that the second return Ping packet is considered to be late because it is not received by the
Netopia R2121 before the third Ping packet is sent. The first and third return Ping packets are on time.
Download from Www.Somanuals.com. All Manuals Search And Download.
15-4 User’s Reference Guide
time
send Ping packet 1
Netopia
receive Ping packet 1
host
host
send return Ping packet 1
receive return Ping packet 1
Netopia
Netopia
send Ping packet 2
receive Ping packet 2
send return Ping packet 2
host
host
send Ping packet 3
Netopia
Netopia
receive return Ping packet 2
receive Ping packet 3
host
host
send return Ping packet 3
receive return Ping packet 3
Netopia
Packets Lost: The number of packets unaccounted for, shown in total and as a percentage of total packets
sent. This statistic may be updated during the Ping test, and may not be accurate until after the test is over.
However, if an escalating one-to-one correspondence is seen between Packets Out and Packets Lost, and
Packets In is noticeably lagging behind Packets Out, the destination is probably unreachable. In this case, use
STOP PING.
Round Trip Time (Min/ Max/ Avg): Statistics showing the minimum, maximum, and average number of
seconds elapsing between the time each Ping packet was sent and the time its corresponding return Ping
packet was received.
The time-to-live (TTL) value for each Ping packet sent by the Netopia R2121 is 255, the maximum allowed. The
TTL value defines the number of IP routers that the packet can traverse. Ping packets that reach their TTL value
are dropped, and a “destination unreachable” notification is returned to the sender (see the table above). This
ensures that no infinite routing loops occur. The TTL value can be set and retrieved using the SNMP MIB-II ip
group’s ipDefaultTTL object.
Trace Route
You can count the number of routers between your Netopia Router and a given destination with the Trace Route
utility.
Select Trace Route in the Statistics & Diagnostics screen and press Return to go to the Trace Route screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Diagnostics 15-5
Trace Route
Host Name or IP Address:
Maximum Hops:
Timeout (seconds):
30
5
Use Reverse DNS:
Yes
START TRACE ROUTE
Enter the IP Address/Domain Name of a host.
Trace route to a network host.
To trace a route, follow these steps:
1. Select Host Name or IP Address and enter the name or address of the destination you want to trace.
2. Select Maximum hops (1..64) to set the maximum number of routers to count between the Netopia Router
and the destination router, up to the maximum of 64. The default is 30 hops.
3. Select Timeout per probe (1..10 sec) to set when the trace will timeout for each hop, up to 10 seconds.
The default is 3 seconds.
4. Select Use Reverse DNS to learn the names of the routers between the Netopia Router and the destination
router. The default is Yes.
5. Select START TRACE ROUTE and press Return. The screen will be replaced by a scrolling screen, listing
the destination, the number of hops, the IP addresses of each hop, and the DNS names, if selected.
6. Cancel the trace by pressing Escape. Return to the Trace Route screen by pressing Escape twice.
Telnet client
The Telnet client mode replaces the normal menu mode. Telnet sessions can be cascaded, that is, you can
initiate a Telnet client session when using a Telnet console session. To activate the Telnet client, select Telnet
from the Utilities & Diagnostics menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
15-6 User’s Reference Guide
The Telnet client screen appears.
Telnet
Host Name or IP Address:
Control Character to Suspend:
Q
START A TELNET SESSION
Enter the IP Address/Domain Name of a host.
■
Enter the host name or the IP address in dotted decimal format of the machine you want to telnet into and
press Return.
■
■
■
■
Either accept the default control character "Q" used to suspend the Telnet session, or type a different one.
START A TELNET SESSION becomes highlighted.
Press Return and the Telnet session will be initiated.
To suspend the session, press Control-Q, or whatever other control character you specified.
Two new options will appear in the Telnet screen (not shown):
Resume Suspended Session – select this one if you want to go back to your Telnet session
Terminate Suspended Session – select this one if you want to end the session
Secure Authentication Monitor
Note: The Secure Authentication Monitor field will remain hidden if PAP-TOKEN or CACHE-TOKEN is not the
selected authentication method in the Connection Profile.
You use the Secure Authentication Monitor screen when placing one type of SecurID connection call. See
“Connecting using security authentication” on page 14-39 for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Diagnostics 15-7
Disconnect Telnet Console Session
If you want to close your Telnet Console session, select Disconnect Telnet Console Session and press Return.
A dialog box appears asking you to cancel or continue your selection.
Utilities & Diagnostics
+------------------------------------------------------+
+------------------------------------------------------+
|
|
| Are you sure you want to close this Console Session? |
|
|
|
|
|
|
|
|
CANCEL
CONTINUE
+------------------------------------------------------+
X-Modem File Transfer...
Revert to Factory Defaults...
Restart System...
If you select Continue, you will immediately terminate your session.
Factory defaults
You can reset the Netopia R2121 to its factory default settings. Select the Revert to Factory Defaults item in
the Statistics & Diagnostics screen and press Return. Select CONTINUE in the dialog box and press Return.
The Netopia R2121 will reboot and its settings will return to the factory defaults, deleting your configurations.
In an emergency, you can also use the Reset Switch to return the router to its factory default settings. Call
Netopia Tech Support for instructions on using the Reset Switch.
Note: Reset to factory defaults with caution. You will need to reconfigure all your settings in the router.
Transferring configuration and firmware files with TFTP
Trivial File Transfer Protocol (TFTP) is a method of transferring data over an IP network. TFTP is a client-server
application, with the Router as the client. To use the Router as a TFTP client, a TFTP server must be available.
Netopia, Inc. has a public access TFTP server on the Internet where you can obtain the latest firmware versions.
To use TFTP, select Trivial File Transfer Protocol (TFTP) in the Statistics & Diagnostics screen and press
Return to go to the Trivial File Transfer Protocol (TFTP) screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
15-8 User’s Reference Guide
Trivial File Transfer Protocol (TFTP)
TFTP Server Name:
Firmware File Name:
GET FIRMWARE FROM SERVER...
GET MODEM FIRMWARE FROM SERVER...
Config File Name:
GET CONFIG FROM SERVER...
SEND CONFIG TO SERVER...
TFTP Transfer State -- Idle
TFTP Current Transfer Bytes -- 0
The sections below describe how to update the Router’s firmware and how to download and upload
configuration files.
Updating firmware
Firmware updates may be available periodically from Netopia or from a site maintained by your organization’s
network administrator.
There are two types of firmware in the Netopia R2121 Dual Analog Router: router firmware and modem
firmware. The router firmware governs how the router communicates with your network and the modems; the
modem firmware governs how the modems communicate with the remote site. Modem firmware, for example to
support the ITU V.90 standard, is included on your Netopia CD for XMODEM transfer and later updates will be
available on the Netopia website. Router firmware updates are also periodically posted on the Netopia website.
To update either the Router’s or the internal modems’ firmware, follow these steps:
■
■
Select TFTP Server Name and enter the server name or IP address of the TFTP server you will use. The
server name or IP address is available from the site where the server is located.
Select Firmware File Name and enter the name of the file you will download. The name of the file is
available from the site where the server is located. You may need to enter a file path along with the file
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Diagnostics 15-9
name (for example, bigroot/ config/ myfile).
■
Select Send Firmware to Netopia from TFTP Server and press Return. You will see the following dialog box:
+-----------------------------------------------------------+
+-----------------------------------------------------------+
|
|
|
|
|
|
|
Are you sure you want to read the firmware now?
The device will reset when the transfer is complete. |
|
|
|
CANCEL
CONTINUE
|
+-----------------------------------------------------------+
■
Select CANCEL to exit without downloading the file, or select CONTINUE to download the file. The system
will reset at the end of the file transfer to put the new firmware into effect. While the system resets, the
LEDs will blink on and off.
Caution!
■
Be sure the firmware update you load onto your router is the correct version for your particular model.
Some models do not support all firmware versions. Loading an incorrect firmware version can permanently
damage the unit.
■
■
Do not manually power down or reset the Netopia R2121 while it is automatically resetting or it could be
damaged.
If you choose to download the firmware, the TFTP Transfer State item will change from Idle to Reading
Firmware. The TFTP Current Transfer Bytes item will reflect the number of bytes transferred.
Downloading configuration files
The Router can be configured by downloading a configuration file using TFTP. Once downloaded, the file
reconfigures all of the Router’s parameters as if someone had manually done so through the console port.
To download a configuration file, follow these steps:
■
■
Select TFTP Server Name and enter the server name or IP address of the TFTP server you will use. The
server name or IP address is available from the site where the server is located.
Select Config File Name and enter the name of the file you will download. The name of the file is available
from the site where the server is located. You may need to enter a file path along with the file name (for
Download from Www.Somanuals.com. All Manuals Search And Download.
15-10 User’s Reference Guide
example, bigroot/ config/ myfile).
■
Select Read Config Now and press Return. You will see the following dialog box:
+-----------------------------------------------------------+
+-----------------------------------------------------------+
|
|
|
|
|
|
|
Are you sure you want to read the configuration now? |
The device will reset when the transfer is complete. |
|
CANCEL
CONTINUE
|
|
+-----------------------------------------------------------+
■
Select CANCEL to exit without downloading the file, or select CONTINUE to download the file. The system
will reset at the end of the file transfer to put the new configuration into effect.
■
If you choose to download the configuration file, the TFTP Transfer State item will change from Idle to
Uploading configuration files
Using TFTP, you can send a file containing a snapshot of the Router’s current configuration to a TFTP server. The
file can then be downloaded by a different Netopia R2121 unit to configure its parameters (see “Downloading
configuration files” on page 15-9). This is useful for configuring a number of Routers with identical parameters,
or just for creating configuration backup files.
Uploading a file can also be useful for troubleshooting purposes. The uploaded configuration file can be tested
on a different Netopia R2121 unit by Netopia or your network administrator.
To upload a configuration file, follow these steps:
1. Select TFTP Server Name and enter the server name or IP address of the TFTP server you will use. The
server name or IP address is available from the site where the server is located.
2. Select Config File Name and enter a name for the file you will upload. The file will appear with the name you
choose on the TFTP server. You may need to enter a file path along with the file name (for example,
Mypc/ Netopia/ myfile).
3. Select Write Config Now and press Return. Netopia will begin to transfer the file.
4. The TFTP Transfer State item will change from Idle to Writing Config. The TFTP Current Transfer Bytes
item will reflect the number of bytes transferred.
Transferring configuration and firmware files with XMODEM
You can transfer configuration and firmware files with XMODEM through the Netopia R2121’s console port. Be
sure your terminal emulation program supports XMODEM file transfers.
To go to the X-Modem File Transfer screen, select it in the Utilities & Diagnostics screen.
Note: The X-Modem File Transfer screen is only available if you are connected via the Console port.
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Diagnostics 15-11
X-Modem File Transfer
Send Firmware to Netopia...
Send Config to Netopia...
Receive Config from Netopia...
Send Firmware to Netopia Internal modem...
Modem Firmware Status:
IDLE
Updating firmware
Firmware updates may be available periodically from Netopia or from a site maintained by your organization’s
network administration.
The procedure below applies whether you are using the console or the built-in modems.
Follow these steps to update the Netopia R2121’s firmware:
1. Make sure you have the firmware file on disk and know the path to its location.
2. Select Send Firmware to Netopia (or Send Firmware to Netopia WAN module) and press Return. The
following dialog box appears:
+--------------------------------------------------------------------+
+--------------------------------------------------------------------+
| Are you sure you want to send a firmware file to your Netopia?
|
| If so, when you hit Return/Enter on the CONTINUE button, you will |
| have 10 seconds to begin the transfer from your terminal program. |
|
|
|
|
|
|
|
|
CANCEL
CONTINUE
+--------------------------------------------------------------------+
3. Select CANCEL to exit without downloading the file, or select CONTINUE to download the file.
If you choose CONTINUE, you will have ten seconds to use your terminal emulation software to initiate an
XMODEM transfer of the firmware file. If you fail to initiate the transfer in that time, the dialog box will
disappear and the terminal emulation software will inform you of the transfer’s failure. You can then try
again.
Download from Www.Somanuals.com. All Manuals Search And Download.
15-12 User’s Reference Guide
The system will reset at the end of a successful file transfer to put the new firmware into effect. While the
system resets, the LEDs will blink on and off.
Caution!
Do not manually power down or reset the Netopia R2121 while it is automatically resetting or it could be
damaged.
Downloading configuration files
The Netopia R2121 can be configured by downloading a configuration file. The downloaded file reconfigures all
of the Router’s parameters.
Configuration files are available from a site maintained by your organization’s network administrator or from
your local site (see “Uploading configuration files,” below).
Follow these steps to download a configuration file:
1. Make sure you have the configuration file on disk and know the path to its location.
2. Select Send Config to Netopia and press Return. The following dialog box appears:
+--------------------------------------------------------------------+
+--------------------------------------------------------------------+
|
|
| Do you want to send a saved configuration to your Netopia?
| If so, when you hit Return/Enter on the CONTINUE button, you will |
| have 10 seconds to begin the transfer from your terminal program. |
|
|
|
|
|
|
|
CANCEL
CONTINUE
+--------------------------------------------------------------------+
3. Select CANCEL to exit without downloading the file, or select CONTINUE to download the file.
If you choose CONTINUE, you will have ten seconds to use your terminal emulation software to initiate an
XMODEM transfer of the configuration file. If you fail to initiate the transfer in that time, the dialog box will
disappear and the terminal emulation software will inform you of the transfer’s failure. You can then try
again.
The system will reset at the end of a successful file transfer to put the new configuration into effect.
Uploading configuration files
A file containing a snapshot of the Netopia R2121’s current configuration can be uploaded from the Router to
disk. The file can then be downloaded by a different Netopia R2121 to configure its parameters (see
“Downloading configuration files” on page 15-12). This is useful for configuring a number of Routers with
identical parameters, or for creating configuration backup files.
Uploading a file can also be useful for troubleshooting purposes. The uploaded configuration file can be tested
on a different Netopia R2121 by Netopia or your network administrator.
The procedure below applies whether you are using the console or the built-in modems.
To upload a configuration file:
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities and Diagnostics 15-13
1. Decide on a name for the file and a path for saving it.
2. Select Receive Config from Netopia and press Return. The following dialog box appears:
+--------------------------------------------------------------------+
|
|
| Are you sure you want to save your current Netopia configuration? |
| If so, when you hit Return/Enter on the CONTINUE button, you will |
| have 10 seconds to begin the transfer from your terminal program. |
|
|
|
|
|
|
CANCEL
CONTINUE
+--------------------------------------------------------------------+
3. Select CANCEL to exit without uploading the file, or select CONTINUE to upload the file.
If you choose CONTINUE, you will have ten seconds to use your terminal emulation software to initiate an
XMODEM transfer of the configuration file. If you fail to initiate the transfer in that time, the dialog box will
disappear and the terminal emulation software will inform you of the transfer’s failure. You can then try
again.
Restarting the system
You can restart the system by selecting the Restart System item in the Utilities & Diagnostics screen.
You must restart the system whenever you reconfigure the Netopia R2121 and want the new parameter values
to take effect. Under certain circumstances, restarting the system may also clear up system or network
malfunctions. Some configuration processes automatically restart the system to apply the changes you have
made.
Download from Www.Somanuals.com. All Manuals Search And Download.
15-14 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting A-1
Appendix A
Troubleshooting
This appendix is intended to help you troubleshoot problems you may encounter while setting up and using the
Netopia R2121. It also includes information on how to contact Netopia Technical Support.
Important information on these problems may be found in the event histories kept by the Netopia R2121.
This section covers the following topics:
■
■
■
“Configuration problems” on page A-1
“Power outages” on page A-3
“Technical support” on page A-3
Configuration problems
If you encounter problems during your initial configuration process, review the following suggestions before
calling for technical support. There are four zones to consider when troubleshooting initial configuration:
1. the computer’s connection to the router;
2. the router’s connection to the telecommunication line(s);
3. the telecommunication line’s connection to your ISP, and
4. the ISP’s connection to the Internet.
If the connection from the computer to the router was not successful, check the following:
■
■
■
■
The Netopia R2121 is turned on.
An Ethernet cable connects your PC’s Ethernet card or built-in Ethernet port to the Netopia R2121.
The SmartStart application is running and able to access the Netopia R2121.
Telnet is available on your PC or Macintosh. (On a PC, it must be specified in your system path. You can
usually find the application as “c:\ windowselnet.exe”.)
■
■
■
Your PC or Macintosh is properly configured for TCP/ IP.
Your PC or Macintosh has an IP address.
Your PC or Macintosh has a subnet mask that matches or is compatible with the Netopia R2121’s subnet
mask.
■
If you are entering a new IP address via SmartStart be sure the correct serial number was entered.
Note: If you are attempting to modify the IP address or subnet mask from a previous, successful configuration
attempt, you will need to clear the IP address or reset your Netopia R2121 to the factory default before
reinitiating the configuration process. For further information on resetting your Netopia R2121 to factory
default, see “Factory defaults” on page 15-7.
Download from Www.Somanuals.com. All Manuals Search And Download.
A-2 User’s Reference Guide
SmartStart Troubleshooting
The Status field of the SmartStart application will display information and indicate problems as they are
detected.
Console connection problems
Can’t see the configuration screens (nothing appears)
■
Check the cable connection from the Netopia R2121’s console port to the computer being used as a
console.
■
Check that the terminal emulation software is accessing the correct port on the computer that’s being
used as a console.
■
■
Try pressing Ctrl-L or Return or the ▲ up or down ▼ key several times to refresh the terminal screen.
Check that flow control on serial connections is turned off.
Junk characters appear on the screen
■
Check that the terminal emulation software is configured correctly.
Check the baud rate. The default values are 9600, N, 8, and 1.
■
Characters are missing from some of the configuration screens
■
Try changing the Netopia R2121’s default speed of 9600 bps and setting your terminal emulation software
to match the new speed.
Network problems
Problems communicating with remote IP hosts
■
Verify the accuracy of the default gateway’s IP address (entered in the IP Setup or Easy Setup screen).
■
Use the Netopia R2121’s ping utility, in the Statistics, Tests, Utilities screen, and try to ping local and
remote hosts. See “Ping” on page 15-2 for instructions on how to use the ping utility. If you can
successfully ping hosts using their IP addresses but not their domain names (198.34.7.1 but not
garcia.netopia.com, for example), verify that the DNS server’s IP address is correct and that it is reachable
from the Netopia R2121 (use ping).
■
If you are using filters, check that your filter sets are not blocking the type of connections you are trying to
make.
Local routing problems
■
Observe the Ethernet LEDs to see if data traffic flow appears to be normal.
■
Check the WAN Statistics and LAN Statistics screens to see more specific information on data traffic flow
and address serving.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting A-3
Power outages
If you suspect that power was restored after a power outage, and the Netopia R2121 is connected to a remote
site, you may need to switch the Netopia R2121 off and then back on again. After temporary power outages, a
connection that still seems to be up may actually be disconnected. Rebooting the Router should reestablish the
connection.
Technical support
Netopia, Inc. is committed to providing its customers with reliable products and documentation, backed by
excellent technical support.
Before contacting Netopia
Look in this guide for a solution to your problem. You may find a solution in this troubleshooting appendix or in
other sections. Check the index for a reference to the topic of concern. If you cannot find a solution, complete
the environment profile below before contacting technical support.
Environment profile
■
Locate the Netopia R2121’s model number, product serial number, and firmware version. The serial
number is on the bottom side of the Router, along with the model number. The firmware version appears in
the Netopia R2121’s Main Menu screen.
Model number:
Serial number:
Firmware version:
■
What kind of local network(s) do you have, with how many devices?
Ethernet
LocalTalk
EtherTalk
TCP/ IP
IPX
Other:
How to reach us
We can help you with your problem more effectively if you have completed the environment profile in the
previous section. If you contact us by telephone, please be ready to supply Netopia Technical Support with the
information you used to configure the Netopia R2121. Also, please be at the site of the problem and prepared
to reproduce it and to try some troubleshooting steps.
When you are prepared, contact Netopia Customer Service by e-mail, telephone, fax, or post:
Internet: techsports@netopia.com (for technical support)
info@netopia.com (for general information)
Download from Www.Somanuals.com. All Manuals Search And Download.
A-4 User’s Reference Guide
Phone: 1 800-782-6449
Fax: 1 510-814-5023
Netopia, Inc.
Customer Service
2470 Mariner Square Loop
Alameda, California 94501
USA
Netopia Bulletin Board Service: 1 510-865-1321
Online product information
Product information can be found in the following:
Netopia World Wide Web server via http:/ / www.netopia.com
Internet via anonymous FTP to ftp.netopia.com/ pub
FAX-Back
This service provides technical notes which answer the most commonly asked questions, and offer solutions
for many common problems encountered with Netopia products.
FAX-Back: +1 510-814-5040
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Internet Services B-1
Appendix B
Setting Up Internet Services
This section covers the following topics:
■
■
■
“Finding an Internet service provider” on page B-1
“Deciding on an ISP account” on page B-2
“Obtaining information from the ISP” on page B-3
Note: Some companies act as their own ISP. For example, some organizations have branch offices that can
use the Netopia R2121 to access the Internet via the main office in a point-to-point scenario. If you install the
Netopia R2121 in this type of environment, refer to the following sections for specific information you must
receive from the network administrator to configure the Netopia R2121 properly.
Finding an Internet service provider
During the setup session, the SmartStart setup application will provide you with a list of service providers who
support the Netopia R2121 with Dual Analog. You can register with one of these ISPs as part of setting up your
router.
If you have purchased your Netopia R2121 through a Netopia ISP partner, you may have received a customized
configuration file from the ISP that will allow you to make an immediate connection when you run SmartStart.
Internet access is available from other Internet service providers. Typically, there are several ISPs in each area.
To locate ISPs in your area, consult your telephone book, local computer magazines, the business section of a
local newspaper, or the following URL on the Internet: ‘http:/ / thelist.internet.com’. Also see Netopia’s home
page at ‘http:/ / www.netopia.com’ for a list of ISPs with special programs and promotions for Netopia
customers.
If your area has more than one ISP, the following considerations may help you decide which ISP is best suited
for your requirements.
Use an ISP that provides Internet access through a V.90 or K56flex line and supports dual analog LAN
connections using Multilink PPP. If you would like to use an ISP that you already have a relationship with but is
not familiar with the Netopia R2121 Dual Analog Router or using Multilink PPP with analog modems, call us at
1-800-NETOPIA. Our representative can call your ISP and introduce them to the product. As necessary, we can
provide them with the technical background they need to support the product.
See “About 56K Line Access” on page H-1 for more information on 56K modem connections.
Download from Www.Somanuals.com. All Manuals Search And Download.
B-2 User’s Reference Guide
Unique requirements
Make sure the ISP can meet any unique requirements you may have. Potential requirements include:
■
■
■
■
■
■
Dynamic or static IP addressing
Class C IP address
Custom domain name
Multiple email addresses
Web site hosting
Call back for web site hosting at your site
Pricing and support
Compare pricing, service, and technical support service among various ISPs.
ISP’s Point of presence
Check with your ISP for the location of their nearest point of presence (POP) in reference to your site. In some
instances, the ISP that you choose may not offer a POP in your local area. If that is the case, you may incur
additional fees for long-distance calls.
Endorsements
Consider recommendations from colleagues and reviews in publications. Netopia lists Netopia Certified ISPs on
our web site at ‘http:/ / www.netopia.com’.
Deciding on an ISP account
Your ISP may offer various Internet access account plans. Typically, these plans vary by usage charges and the
number of host IP addresses supplied. Evaluate your networking needs and discuss them with your ISP before
deciding on a plan for your network.
The following checklist is a guide to ensure you obtain the Internet service you require.
Setting up a Netopia R2121 account
Check whether your ISP has the Netopia R2121 on a list of supported products that have been tested with a
particular configuration. If the ISP does not have the Netopia R2121 on such a list, describe the Netopia R2121
in as much detail as needed, so your ISP account can be optimized. As appropriate, you may refer your ISP to
Netopia’s web site for more information.
Obtaining an IP host address
Typically, each computer on the network that requires Internet access requires its own unique IP address. If
some or all network computers require simultaneous Internet access, obtain a block of IP host addresses large
enough for each computer to have its own address, plus one for the Netopia R2121.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Internet Services B-3
Consider expected growth in your network when deciding on the number of addresses to obtain. Alternatively,
you may use the Network Address Translation feature of SmartIP.
SmartIP™
Network Address Translation provides Internet access to the network connected to the Netopia R2121 using
only a single IP address. These routers translate between the internal or local area network (LAN) addresses
and a single external IP address and route accordingly.
For more information on Network Address Translation, see Chapter 10, “IP Setup, SmartIP and Network
Address Translation.”
Obtaining information from the ISP
After your account is set up, the ISP should send you the IP parameter information that will help you to configure
the Netopia R2121.
Local LAN IP address information to obtain (NAT enabled)
If you are using SmartIP (NAT), you should obtain the following:
■
If you are dialing out to a remote site using Network Address Translation on your router, your provider will
not define the IP address information on your local LAN. You can define this information based on
parameters defined by another connection profile such as that to a corporate network, or an IP
configuration that may already be in place for the existing network. Alternatively, you can use the default IP
address range used by the router.
■
■
Primary and Secondary Domain Name Server (DNS) IP Addresses
Domain Name (usually the same as the ISP’s domain name unless you have registered for your own
individual domain name)
Remote WAN IP address information to obtain
■
■
■
Telephone number of the ISP’s local or nearby dial-up POP (point-of-presence).
PPP authentication type for router at the ISP, such as PAP.
Send and receive User Login name and Send and receive User Password if PAP or CHAP security
authentication is used
Local LAN IP address information to obtain (NAT-disabled)
If you are not using SmartIP (NAT), you should obtain:
■
The number of Ethernet IP host addresses available with your account and the first usable IP host address
Download from Www.Somanuals.com. All Manuals Search And Download.
B-4 User’s Reference Guide
in the address block
■
■
■
■
■
The Ethernet IP address for your Netopia R2121
The Ethernet IP subnet mask address for your Netopia R2121
The Default Gateway IP Address (same as Remote IP Address in most cases)
Primary and Secondary Domain Name Server IP Addresses
Domain Name (usually the same as the ISP’s domain name unless you have registered for your own
individual domain name)
Note: If you are not using Network Address Translation, you will need to obtain all of the Local LAN IP address
information from your ISP.
Remote WAN IP address information to obtain
■
■
■
■
■
The telephone number of the ISP’s local or nearby dial-up POP (point-of-presence).
Remote IP address of router at ISP or other remote site
Remote IP subnet mask address of router at ISP or other remote site
PPP authentication type for router at the ISP, such as PAP.
Send User Login name and Send User Password if PAP or CHAP security authentication is used
Note: If you are not using Network Address Translation, you will need to obtain all of the Remote WAN IP
address information from your ISP.
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding IP Addressing C-1
Appendix C
Understanding IP Addressing
This appendix is a brief general introduction to IP addressing. A basic understanding of IP will help you in
configuring the Netopia R2121 and using some of its powerful features, such as static routes and packet
filtering.
In packets, a header is part of the envelope information that surrounds the actual data being transmitted. In
■
■
■
■
■
“About IP addressing” on page C-1
“Distributing IP addresses” on page C-5
“Nested IP subnets” on page C-11
“Broadcasts” on page C-13
What is IP?
All networks use protocols to establish common standards for communication. One widely used network
protocol is the Internet Protocol, also known as IP. Like many other protocols, IP uses packets, or formatted
chunks of data, to communicate.
Note: This guide uses the term “IP” in a very general and inclusive way, to identify all of the following:
■
Networks that use the Internet Protocol, along with accompanying protocols such as TCP, UDP, and
ICMP
■
■
Packets that include an IP header within their structure
Devices that send IP packets
About IP addressing
Every networking protocol uses some form of addressing in order to ensure that packets are delivered correctly.
In IP, individual network devices that are initial sources and final destinations of packets are usually called
hosts, instead of nodes, but the two terms are interchangeable. Each host on an IP network must have a
unique IP address. An IP address, also called an Internet address, is a 32-bit number usually expressed as four
decimal numbers separated by periods. Each decimal number in an IP address represents a 1-byte (8-bit) binary
number. Thus, values for each of the four numbers range from 00000000 to 11111111 in binary notation, or
from 0 to 255 in decimal notation. The expression 192.168.1.1 is a typical example of an IP address.
Download from Www.Somanuals.com. All Manuals Search And Download.
C-2 User’s Reference Guide
IP addresses indicate both the identity of the network and the identity of the individual host on the network. The
number of bits used for the network number and the number of bits used for the host number can vary, as long
as certain rules are followed. The local network manager assigns IP host numbers to individual machines.
IP addresses are maintained and assigned by the InterNIC, a quasi-governmental organization now increasingly
under the auspices of private industry.
Note: It’s very common for an organization to obtain an IP address from a third party, usually an Internet
service provider (ISP). ISPs usually issue an IP address when they are contracted to provide Internet access
services.
The InterNIC (the NIC stands for Network Information Center) divides IP addresses into several classes.
Classes A, B, and C are assigned to organizations who request addresses. In Class A networks, the first byte of
an IP address is reserved for the network portion of the address. Class B networks reserve the first two bytes
of an IP address for the network address. Class C networks reserve the first three bytes of an IP address for the
network address. In all cases, a network manager can decide to use subnetting to assign even more bits to the
network portion of the IP address, but never less than the class requires. The following section gives more
information on subnetting.
Class A networks have a small number of possible network numbers, but a large number of possible host
numbers. Conversely, Class C networks have a small number of possible host numbers, but a large number of
possible network numbers. Thus, the InterNIC assigns Class A addresses to large organizations that have very
large numbers of IP hosts, while smaller organizations, with fewer hosts, get Class B or Class C addresses. You
can tell the various classes apart by the value of the first (or high-order) byte. Class A networks use values from
1 to 127, Class B networks use values from 128 to 191, and Class C networks use values from 192 to 223.
The following table summarizes some of the differences between Class A, B, and C networks.
Number of
networks
possible per
class
Number of
hosts
possible per
network
Format of address
(without subnetting)
Class
First byte
Example
A
B
C
1-127
128-191
192-223
127
16,384
16,777,214
65,534
254
net.host.host.host
net.net.host.host
net.net.net.host
97.3.14.250
140.100.10.11
197.204.13.7
2,097,152
Subnets and subnet masks
Often an entire organization is assigned only one IP network number. If the organization has several IP networks
connected together with IP routers, the network manager can use subnetting to distinguish between these
networks, even though they all use the same network number. Each physical network becomes a subnet with a
unique subnet number.
Subnet numbers appear within IP addresses, along with network numbers and host numbers. Since an IP
address is always 32 bits long, using subnet numbers means either the network number or the host numbers
must use fewer bits, in order to leave room for the subnet numbers. Since the InterNIC assigns the network
number proper, it should not change, so the subnet numbers must be created out of bits that would otherwise
be part of the host numbers.
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding IP Addressing C-3
Subnet masks
To create subnets, the network manager must define a subnet mask, a 32-bit number that indicates which bits
in an IP address are used for network and subnetwork addresses, and which are used for host addresses. One
subnet mask should apply to all IP networks that are physically connected together and share a single assigned
network number. Subnet masks are often written in decimal notation, like IP addresses, but they are most
easily understood in binary notation. When a subnet mask is written in binary notation, each numeral 1
indicates that the corresponding bit in the IP address is part of the network or subnet address. Each 0
indicates that the corresponding bit is part of the host address. The following table shows the proper subnet
masks to use for each class of network, when no subnets are required.
Class
Subnet mask for a network with no subnets
Binary: 11111111.00000000.00000000.00000000
Decimal: 255.0.0.0
A
Binary: 11111111.11111111.00000000.00000000
Decimal: 255.255.0.0
B
C
Binary: 11111111.11111111.11111111.00000000
Decimal: 255.255.255.0
To know whether subnets are being used or not, you must know what subnet mask is being used—you cannot
determine this information simply from an IP address. Subnet mask information is configured as part of the
process of setting up IP routers and gateways such as the Netopia R2121.
Note: If you receive a routed account from an ISP, there must be a mask associated with your network IP
address. By using the IP address with the mask you can discover exactly how many IP host addresses you
actually have.
To configure subnets properly, you must also be able to convert between binary notation and decimal notation.
Example: Using subnets on a Class C IP internet
When setting up IP routing with a Class A Address, or even multiple Class C Addresses, subnetting is fairly
straightforward. Subnetting a single Class C address between two networks, however, is more complex. This
section describes the general procedures for subnetting a single Class C network between two Netopia routers
so that each can have Internet access.
Download from Www.Somanuals.com. All Manuals Search And Download.
C-4 User’s Reference Guide
Network configuration
Below is a diagram of a simple network configuration. The ISP is providing a Class C address to the customer
site, and both networks A and B want to gain Internet access through this address. Netopia R2121 B connects
to Netopia R2121 A and is provided Internet access through Routers A and B.
Customer Site A
PC 1:
IP Address: 192.168.1.3
Subnet Mask:
255.255.255.128
Gateway: 192.168.1.1
Router B:
Netopia R2121 A:
IP Address: 192.168.1.1
IP Address: 192.168.1.2
Subnet Mask: 255.255.255.128
Subnet Mask:
Remote IP: 10.0.0.1
LAN
255.255.255.128
Remote Sub: 255.255.255.0
Gateway: 10.0.0.1
ISP Network
Router A:
Remote IP: 192.168.1.129
Remote Sub:
255.255.255.128
Static Route:
192.168.1.128 [network]
255.255.255.128 [mask]
192.168.1.2 [via router]
IP Address: 10.0.0.1
Gateway: 192.168.1.1
Subnet Mask: 255.255.255.0
Usable IP Addresses avail-
able to Customer Site A:
192.168.1.1 -->
Usable IP Addresses available to
Customer Site A: 192.168.1.1 -->
192.168.1.126
192.168.1.126
Customer Site B
Netopia R2121 B:
PC 2:
IP Address: 192.168.1.129
Subnet Mask: 255.255.255.128
Remote IP: 192.168.1.2
IP Address:
192.168.1.130
Internet
Subnet Mask:
255.255.255.128
Remote Sub: 255.255.255.128
Gateway: 192.168.1.2
Gateway:
192.168.1.129
Usable IP Addresses available to
Customer Site B: 192.168.1.129
--> 192.168.1.254
LAN
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding IP Addressing C-5
Background
The IP Addresses and routing configurations for the devices shown in the diagram are outlined below. In
addition, each individual field and its meaning are described.
The “IP Address” and “Subnet Mask” fields define the IP Address and Subnet Mask of the device's Ethernet
connection to the network while the “Remote IP” and “Remote Sub” fields describe the IP Address and Subnet
mask of the remote router. This information is entered in the Connection Profile of the Netopia R2121.
The “Gateway” field describes the router or workstation's default gateway or, where they will send their packets
if the appropriate route is not known. The “Static Route” field, which is only shown on Router B, tells Router B
what path to take to get to the network defined by Netopia R2121 B. Finally, the “Usable IP Address” field
shows the range of IP Addresses available to the hosts of that network.
Note that the IP Addresses given in this section are for example purposes only. Do not use these addresses
when configuring your network.
With this configuration, both Customer Site A and B can gain Internet access through Routers A and B, with no
reconfiguration of the ISP's equipment. The most important item in this configuration is the Static Route
defined on Router B. This tells Router B what path to take to get to the network defined by Netopia R2121 B.
Without this information, Customer Site B will be able to access Customer Site A, but not the Internet.
If it is not possible to define a Static Route on Router B, RIP could be enabled to serve the same purpose. To
use RIP instead of a Static Route, enable Transmit RIP on Netopia R2121 A and Transmit and Receive RIP on
Router B. This will allow the route from Customer Site B to propagate on Router B and Customer Site A.
Example: Working with a Class C subnet
Suppose that your organization has a site with only 10 hosts, and no plans to add any new hosts. You don’t
need a full Class C address for this site. Many ISPs offer Internet access with only a portion of a full Internet
address.
For example, you may obtain the Class C address 199.14.17.48, with the mask 255.255.255.240. From the
previous example, you can see that this gives you 14 host addresses to distribute to the hosts at your site. In
effect, your existing network of 10 hosts is a subnet of the ISP’s network. Since the Class C address has
already been reduced to subnets, you cannot further subnet your network without the risk of creating network
routing problems (since you must use the mask issued by the ISP). This, however, is not a problematic
limitation for your small network.
The advantages to this situation is the greater ease and lower cost of obtaining a subnet from an ISP rather
than a full Class C address.
Distributing IP addresses
To set up a connection to the Internet, you may have obtained a block of IP host addresses from an Internet
service provider. When configuring the Netopia R2121, you gave one of those addresses to its Ethernet port,
leaving a number of addresses to distribute to computers on your network.
Download from Www.Somanuals.com. All Manuals Search And Download.
C-6 User’s Reference Guide
There are two schemes for distributing the remaining IP addresses:
■
■
Manually give each computer an address
Let the Netopia R2121 automatically distribute the addresses
These two methods are not mutually exclusive; you can manually issue some of the addresses while the rest
are distributed by the Netopia R2121. Using the Router in this way allows it to function as an address server.
One reason to use the Netopia R2121 as an address server is that it takes less time than manually distributing
the addresses. This is particularly true if you have many addresses to distribute. You only need to enter
information once, rather than having to repeatedly enter it on each host separately. This also reduces the
potential for misconfiguring hosts.
Another reason to use the Netopia R2121 as an address server is that it will only distribute addresses to hosts
that need to use them.
All Netopia R2121s come with an integrated Dynamic Host Control Protocol (DHCP) server. Some routers also
come with a Macintosh Internet Protocol (MacIP) server. These servers provide a means of distributing IP
addresses to either a Mac or PC workstation as needed.
When setting up the DHCP or MacIP servers in the Netopia R2121, it is necessary to understand how
workstations lease, renew, and release their IP addresses. This information will be helpful in determining
dynamic address allocation for a network.
The term “lease” describes the action of a workstation requesting and using an IP address. The address is
dynamic and can be returned to the address pool at a later time.
The term “renew” refers to what the workstations do to keep their leased IP address. At certain intervals, the
workstation talks to the DHCP or MacIP server and renews the lease on that IP address. This renewal allows
the workstation to keep and use the assigned IP address until the next renewal period.
The term “release” refers to a situation where the workstation is no longer using its assigned IP address or has
been shut down. IP addresses can be manually released as well. The IP address goes back into the DHCP or
MacIP address pool to be reassigned to another workstation as needed.
Technical note on subnet masking
Note: The IP address supplied by the Netopia R2121 will be a unique number. You may wish to replace this
number with a number that your ISP supplies if you are configuring the router for a static IP address. The
automatic IP mask supplied by SmartStart is a Class C address. However, the Netopia R2121 and all devices
on the same local network must have the same subnet mask. If you require a different class address, you may
edit the IP Mask field to enter the correct address. Refer to the table below.
Number of Devices (other than
Netopia R2121) on Local Network
Largest Possible Ethernet Subnet
Mask
1
255.255.255.252
255.255.255.248
255.255.255.240
255.255.255.224
2-5
6-13
14-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding IP Addressing C-7
Number of Devices (other than
Netopia R2121) on Local Network
Largest Possible Ethernet Subnet
Mask
30-61
62-125
125-259
255.255.255.192
255.255.255.128
255.255.255.0
Configuration
This section describes the specific IP address lease, renew, and release mechanisms for both the Mac and PC,
with either DHCP or MacIP address serving.
DHCP Address Serving
Windows 95 Workstation:
■
■
■
The Win95 workstation requests and renews its lease every half hour.
The Win95 workstation does NOT relinquish its DHCP address lease when the machine is shut down.
The lease can be manually expired using the WINIPCFG program from the Win95 machine, which is a
command line program executable from the DOS prompt or from the START:RUN menu.
Windows 3.1 Workstation (MSTCP Version 3.11a):
■
■
The Win3.1 workstation requests and renews its lease every half hour.
The Win3.1 workstation does NOT relinquish its DHCP address lease when the user exits Windows and
goes to DOS.
■
The lease can be manually expired by typing IPCONFIG / RELEASE from a DOS window within Windows or
from the DOS prompt.</ UL>
Macintosh Workstation (Open Transport Version 1.1 or later):
■
■
The Mac workstation requests and renews its lease every half hour.
The Mac workstation will relinquish its address upon shutdown in all but one case. If the TCP/ IP control
panel is set to initialize at start-up, and no IP services are used or the TCP/ IP control panel is not opened,
the DHCP address will NOT be relinquished upon shutdown. However, if the TCP/ IP control panel is
opened, or if an IP application is used, the Mac WILL relinquish the lease upon shutdown.
■
If the TCP/ IP control panel is set to acquire an address only when needed (therefore a TCP/ IP application
must have been launched to obtain a lease) the Mac WILL relinquish its lease upon shutdown every time.
Netopia R2121 DHCP Server Characteristics
■
■
■
The Netopia R2121 ignores any lease-time associated with a DHCP request and automatically issues the
DHCP address lease for one hour.
The number of devices a Netopia R2121 can serve DHCP to is 512. This is imposed by global limits on the
size of the address serving database, which is shared by all address serving functions active in the router.
The Netopia R2121 does release the DHCP address back to the available DHCP address pool precisely
Download from Www.Somanuals.com. All Manuals Search And Download.
C-8 User’s Reference Guide
one hour after the last heard lease request as some other DHCP implementations may hold on to the lease
for an additional time after the lease expired, to act as a buffer for variances in clocks between the client
and server.
MacIP Serving
Macintosh Workstation (MacTCP or Open Transport):
Once the Mac workstation requests and receives a valid address, the Netopia R2121 will actively check for the
workstation’s existence once every minute.
■
For a DYNAMIC address, the Netopia R2121 will release the address back to the address pool after it has
lost contact with the Mac workstation for over 2 minutes.
■
For a STATIC address, the Netopia R2121 will release the address back to the address pool after it has
lost contact with the Mac workstation for over 20 minutes.
Netopia R2121 MacIP Server Characteristics
The Mac workstation uses ATP to both request and receive an address from the Netopia R2121's MacIP server.
Once acquired, NBP confirm packets will be sent out every minute from the Netopia R2121 to the Mac
workstation.
Manually distributing IP addresses
If you choose to manually distribute IP addresses, you must enter each computer’s address into its TCP/ IP
stack software. Once you manually issue an address to a computer, it possesses that address until you
manually remove it. That’s why manually distributed addresses are sometimes called static addresses.
Static addresses are useful in cases when you want to make sure that a host on your network cannot have its
address taken away by the address server. A network administrator’s computer, a computer dedicated to
communicating with the Internet, and routers are appropriate candidates for a static address.
Using address serving
The Netopia R2121 provides three ways to serve IP addresses to computers on a network. The first, Dynamic
Host Configuration Protocol (DHCP), is supported by PCs with Microsoft Windows and a TCP/ IP stack.
Macintosh computers using Open Transport and computers using the UNIX operating system may also be able
to use DHCP. The second way, MacIP, is for Macintosh computers. The third way, called Serve Dynamic WAN
Clients (IPCP), is used to fulfill WAN client requirements
The Netopia R2121 can use both DHCP and MacIP. Whether you use one or both will depend on your particular
networking environment. If that environment includes both PCs and Macintosh computers that do not use Open
Transport, you will need to use both DHCP and MacIP to distribute IP addresses to all of your computers.
Serve dynamic WAN clients
The third method, used to fulfill WAN client requirements, is called Serve Dynamic WAN Clients. This is a subset
of PPP. Originally, this would apply only to switched WAN interface routers, and not to leased line routers.
However, a new feature can give you Asynchronous PPP dial-in support on the Auxiliary port on any router
including leased line Netopia routers.
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding IP Addressing C-9
In any situation where a device is dialing into a Netopia router, the router may need to be configured to serve IP
via the WAN interface. This is only a requirement if the calling device has not been configured locally to know
what its address(es) are. So when a client, dialing into a Netopia router's WAN interface, is expecting
addresses to be served by the answering router, you must set the answering Netopia router to serve IP via its
WAN interface.
You can do this in either of two ways:
■
use the Serve Dynamic WAN Clients option in the Address Serving Setup screen.
Serve Dynamic WAN Clients enabled only allows you to specify a pool of addresses from which the dial-in
client may get an IP address. It does not allow static addressing.
If you want to serve addresses dynamically, use Serve Dynamic WAN Clients.
■
define the address that you want to serve in the Connection Profile's IP Setup screen.
This method requires a static value to be used. Thus any user dialing in can obtain the same IP address for
every connection to the profile.
If you want to serve addresses statically, define the address in the Connection Profile.
Notes:
■
■
The addresses that are to be served cannot be used elsewhere. For example you wouldn't want to
define a static address in a Connection Profile to be served via the WAN that is already defined in the
DHCP pool of addresses.
In order to work correctly, you must define a “host” or “node” address in the IP Profile Parameters of
the Connection Profile.
This is accomplished by specifying the IP address that is to be statically served via the WAN, and then
by entering a mask value of 255.255.255.255.
Tips and rules for distributing IP addresses
■
Before you allocate IP addresses using DHCP and MacIP, consider whether you need to set aside any static
addresses.
■
Note any planned and currently used static addresses before you use DHCP and MacIP.
■
Avoid fragmenting your block of IP addresses. For example, try to use a continuous range for the static
addresses you choose.
Download from Www.Somanuals.com. All Manuals Search And Download.
C-10 User’s Reference Guide
Distributed to the
1
Netopia R2121
1
(Ethernet IP address)
2
3
4
2
Manually distributed
(static)
5
3
6
4
7
8
9
10
11
12
13
14
15
16
5
6
7
8
9
10
11
12
13
14
15
16
Pool of Addresses Distributed
by MacIP and DHCP
Block of IP host addresses
(derived from network IP
address + mask issued by ISP)
The figure above shows an example of a block of IP addresses being distributed correctly.
The example follows these rules:
■
■
■
An IP address must not be used as a static address if it is also in a range of addresses being distributed
by DHCP or MacIP.
A single IP address range is used by all the address-served clients. These include DHCP, BOOTP, MacIP,
and WAN clients, even though BOOTP and static MacIP clients might not be considered served.
The address range specified for address-served clients cannot wrap around from the end of the total
available range back to the beginning. See below for a further explanation and an example.
■
The network address issued by an ISP cannot be used as a host address.
A DHCP example
Suppose, for example, that your ISP gave your network the IP address 199.1.1.32, and a 4-bit subnet mask.
Address 199.1.1.32 is reserved as the network address. Address 199.1.1.47 is reserved as the broadcast
address. This leaves 14 addresses to allocate, from 199.1.1.33 through 199.1.1.46. If you want to allocate a
sub-block of 10 addresses using DHCP, enter “10” in the DHCP Setup screen’s Number of Addresses to
Allocate item. Then, in the same screen’s First Address item, enter the first address in the sub-block to
allocate such that all 10 addresses are within your original block. You could enter 199.1.1.33, or 199.1.1.37,
or any address between them. Note that if you entered 199.1.1.42 as the first address, network routing errors
would probably result because you would be using a range with addresses that do not belong to your network
(199.1.1.49, 199.1.1.50, and 199.1.1.51).
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding IP Addressing C-11
Nested IP subnets
Under certain situations, you may wish to create remote subnets from the limited number of IP addresses
issued by your ISP or other authority. You can do this using connection profiles. These subnets can be nested
within the range of IP addresses available to your network.
For example, suppose that you obtain the Class C network address a.b.c.0 to be distributed among three
networks. This network address can be used on your main network while portions of it can be subnetted to the
two remaining networks.
Note: The IP address a.b.c.0 has letters in place of the first three numbers to generalize it for this example.
The figure at left shows a possible network configuration following this scheme. The main network is set up with
the Class C address a.b.c.0, and contains Router A (which could be a Netopia R2121), a Netopia R2121, and a
number of other hosts. Router A maintains a link to the Internet, and may be used as the default gateway.
Internet
a.b.c.16
a.b.c.1
Router A
a.b.c.0
a.b.c.2
Router B
Router C
a.b.c.248
a.b.c.249
a.b.c.128
a.b.c.129
Download from Www.Somanuals.com. All Manuals Search And Download.
C-12 User’s Reference Guide
Routers B and C (which could also be Netopia R2121s) serve the two remote networks that are subnets of
a.b.c.0. The subnetting is accomplished by configuring the Netopia R2121 with connection profiles for Routers
B and C (see the following table).
Bits available for host
Connection profile
Remote IP address
Remote IP mask
address
for Router B
for Router C
a.b.c.128
a.b.c.248
255.255.255.192
255.255.255.248
7
3
The Netopia R2121’s connection profiles for Routers B and C create entries in its IP routing table. One entry
points to the subnet a.b.c.128, while a second entry points to the subnet a.b.c.248. The IP routing table might
look similar to the following:
IP Routing Table
Network Address-Subnet Mask-----via Router------Port--Age--------Type------
----------------------------------SCROLL UP--------------------------------
0.0.0.0
0.0.0.0
a.b.c.1 WAN
3719
Management
Local
Local
127.0.0.1
a.b.c.128
a.b.c.248
255.255.255.255 127.0.0.1 lp1 6423
255.255.255.192 a.b.c.128 WAN 5157
255.255.255.248 a.b.c.248 WAN 6205
Local
---------------------------------SCROLL DOWN-------------------------------
UPDATE
Let’s see how a packet from the Internet gets routed to the host with IP address a.b.c.249, which is served by
Router C. The packet first arrives at Router A, which delivers it to its local network (a.b.c.0). The packet is then
received by the Netopia R2121, which examines its destination IP address.
The Netopia R2121 compares the packet’s destination IP address with the routes in its IP routing table. It
begins with the route at the bottom of the list and works up until there’s a match or the route to the default
gateway is reached.
When a.b.c.249 is masked by the first route’s subnet mask, it yields a.b.c.248, which matches the network
address in the route. The Netopia R2121 uses the connection profile associated with the route to connect to
Router C, and then forwards the packet. Router C delivers the packet to the host on its local network.
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding IP Addressing C-13
The following diagram illustrates the IP address space taken up by the two remote IP subnets. You can see from
the diagram why the term nested is appropriate for describing these subnets.
1
Address range
available to
a.b.c.0, less
the two nested
subnets
129
valid addresses used
by a.b.c.128
190
249
valid addresses used
by a.b.c.248
254
Broadcasts
As mentioned earlier, binary IP host or subnet addresses composed entirely of ones or zeros are reserved for
broadcasting. A broadcast packet is a packet that is to be delivered to every host on the network, if both the
host address and the subnet address are all ones or all zeros, or to every host on the subnetwork, if the host
address is all ones or all zeros but the subnet address is a combination or zeros and ones. Instead of making
many copies of the packet, individually addressed to different hosts, all the host machines know to pay
attention to broadcast packets, as well as to packets addressed to their specific individual host addresses.
Depending on the age and type of IP equipment you use, broadcasts will be addressed using either all zeros or
all ones, but not both. If your network requires zeros broadcasting, you must configure this through SNMP.
Packet header types
As previously mentioned, IP works with other protocols to allow communication over IP networks. When IP is
used on an Ethernet network, IP works with the Ethernet or 802.3 framing standards, among other protocols.
These two protocols specify two different ways to organize the very first signals in the sequence of electrical
signals that make up an IP packet travelling over Ethernet. By default, the Netopia R2121 uses Ethernet packet
headers for IP traffic. If your network requires 802.3 IP framing, you must configure this through SNMP.
Download from Www.Somanuals.com. All Manuals Search And Download.
C-14 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding Netopia NAT Behavior D-1
Appendix D
Understanding Netopia NAT Behavior
This appendix describes how Network Address Translation works within the Netopia R2121. The Netopia R2121
implements a powerful feature called Network Address Translation (NAT) as specified in RFC 1631. NAT is used
for IP address conservation and for security purposes since there will only be a single IP “presence” on the
WAN. This appendix describes the NAT functionality within the Netopia R2121 and provides examples for setup
and use.
Network Configuration
Below is a diagram of the network referenced in this appendix.
ISP Network
IP: 200.1.1.1
Customer Site
Netopia Router
Netopia Router
WAN IP: 200.1.1.40
Mask: 255.255.255.0
LAN IP: 192.168.5.1
Mask: 255.255.255.240
Mask: 255.255.255.0
MAC: 00-00-c5-60-21-0a MAC: 00-00-c5-60-21-0a
Router
Netopia
Workstation A
IP: 192.168.5.2
Mask: 255.255.255.240
MAC: 00-05-02-04-12-4f
LAN
Internet
WWW Server
IP: 163.176.4.32
Workstation B
IP: 192.168.5.3
Mask: 255.255.255.0
MAC: 00-05-02-0c-1b-41
Mask: 255.255.255.240
MAC: 00-05-02-00-1e-03
Background
NAT is a mechanism employed within the Netopia R2121 to acquire a statically or dynamically assigned IP
address on its WAN interface and proxy against locally assigned IP addresses on its LAN interface. The Netopia
R2121 uses a one-to-many IP address mapping scheme, that is against a single IP address the Netopia R2121
acquires on its WAN interface the Netopia R2121 can proxy 14, 30, or an unlimited number of IP hosts on the
LAN interface.
In order to fully understand how NAT works you must understand how a PPP connection is established and IP
addresses are negotiated.
Download from Www.Somanuals.com. All Manuals Search And Download.
D-2 User’s Reference Guide
When the Netopia R2121 establishes a connection over its WAN interface with another router it uses the Point
to Point Protocol (PPP). Within PPP there is a Network Control Protocol (NCP) called Internet Protocol Control
Protocol (IPCP) which handles the negotiation of IP addresses between the two routers, in this case the Netopia
R2121 at the customer site above and the Router at the Internet Service Provider (ISP).
If the Netopia R2121 calls the Router at the ISP with NAT disabled, the Netopia negotiates its LAN interface
address (as specified in IP Setup within the Netopia R2121's console) with the Router at the ISP through IPCP
and then sets up routing. From the previous diagram you can see that the address for the Netopia R2121 is
192.168.5.1 and the address of the Router at the ISP is 200.1.1.1. Assuming that the addresses negotiated
by the routers are valid and unique for the Internet, the Netopia R2121 and the hosts on its LAN would be able
to access the Internet.
If the Netopia R2121 calls the Router at the ISP with NAT enabled, instead of negotiating the LAN interface
address the Netopia R2121 suggests the address 0.0.0.0 through IPCP. When the Router at the ISP sees this
all-zeros IPCP request, the Router can either pull a free dynamic IP address from its pool and assign it to the
Netopia R2121’s WAN interface or, if configured to do so, match the Netopia R2121's incoming connection
profile and assign a pre-configured static IP address to the Netopia R2121's WAN interface.
From the previous diagram, you can see that the IP address assigned to the Netopia R2121's WAN interface is
200.1.1.40, while the IP address assigned to the LAN interface remains the same. The LAN interface address
192.168.5.1 is thus hidden from the ISP and the Internet, and the Netopia R2121 only has a single valid IP
presence on the Internet. The LAN interface IP address for the Netopia R2121 can be any IP address, however
it is recommended that you use the IANA specified 192.168.X.X Class C address range which is used for
networks not attached to the Internet. This address range is described in RFC 1597.
The dynamic IP address acquisition on the WAN interface of the Netopia R2121 is one of several features of
NAT. Another is the mapping of locally assigned IP addresses to the single globally unique IP address acquired
by the Netopia R2121 on its WAN interface. NAT employs several things to accomplish this seamlessly. You
must look at the formatting of an IP packet before IP address remapping can be explained.
Every IP packet that is transmitted across the Netopia R2121’s LAN interface or across the WAN interface to
the Internet contains several bits of information that indicate to any device where the packet is going and where
it came from. In particular you have the source and destination port and source and destination IP addresses.
A port is used within IP to define a particular type of service and could be either a Transmission Control
Protocol (TCP) port or User Datagram Protocol (UDP) port. Both TCP and UDP are protocols that use IP as the
underlying transport mechanism. The major difference between TCP and UDP is that TCP is a reliable delivery
service whereas UDP is a “best effort” delivery service. A list of well known TCP or UDP ports and services can
be found in RFC 1700.
If Workstation A wants to communicate with a World Wide Web (WWW) Server on the Internet and the Netopia
R2121 does not have NAT enabled, Workstation A forms an IP packet with the source IP address of
192.168.5.2 and destination IP address of 163.176.4.32. The source port could be 400 while the destination
port would be 80 (WWW server). The Netopia R2121 then looks at this IP packet, determines the best routing
method and sends that packet on its way across the WAN interface to the WWW Server on the Internet.
With NAT enabled the Netopia R2121 does something different. For example, suppose that Workstation A again
wants to communicate with the WWW Server on the Internet. Workstation A forms an IP packet with the source
IP address of 192.168.5.2 and destination IP address of 163.176.4.32 and source port could be 400 while
the destination port would be 80 (WWW server).
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding Netopia NAT Behavior D-3
When the Netopia R2121 receives this IP packet, it can not simply forward it to the WAN interface and the
Internet since the IP addresses on the LAN interface are not valid or globally unique for the Internet. Instead the
Netopia R2121 has to change the IP packet to reflect the IP address that was acquired on the WAN interface
from the ISP.
The Netopia R2121 will first substitute the source IP address with the IP address that was acquired on the WAN
interface which in this case is 200.1.1.40. Next the Netopia R2121 will substitute the source TCP or UDP port
with a TCP or UDP port from within a specified range maintained within the Netopia R2121. And finally the
modified IP packet's checksum is recalculated (as specified in RFC 1631) and the packet is transmitted across
the WAN interface to its destination, the WWW Server on the Internet.
If the send and response IP packets were drawn out, this process would look like the following:
Netopia Router
LAN: 192.168.5.1
WAN: 200.1.1.40
WWW Server
163.176.4.32
Workstation A
192.168.5.2
ISP Router
200.1.1.1
Netopia
Router
Wkstn A to Netopia
Netopia to ISP Router
ISP Router to WWW
Src IP: 192.168.5.2
Dst IP: 163.176.4.32
Src Port:: 400
Src IP: 200.1.1.40
Dst IP: 163.176.4.32
Src Port:: 5001
Dst Port:: 80
Src IP: 200.1.1.40
Dst IP: 163.176.4.32
Src Port:: 5001
Dst Port:: 80
Dst Port:: 80
WWW to ISP Router
Src IP: 163.176.4.32
Dst IP: 200.1.1.40
Src Port:: 80
Netopia to Wkstn A
Src IP: 163.176.4.32
Dst IP: 192.168.5.2
Src Port:: 80
ISP Router to Netopia
Src IP: 163.176.4.32
Dst IP: 200.1.1.40
Src Port:: 80
Dst Port:: 5001
Dst Port:: 400
Dst Port:: 5001
As you can see, the IP packet from Workstation A is sent to the Netopia R2121 and the source IP address is
substituted with 200.1.1.40 and the source port is substituted with 5001, then the IP packet checksum is
recalculated. When this modified packet reaches the WWW Server on the Internet, the WWW Server responds
and sends the IP packet back to destination IP address 200.1.1.40 and destination port 5001.
When the Netopia R2121 receives this IP packet from the WWW Server, the Netopia R2121 replaces the
destination IP address with 192.168.5.2, the address for Workstation A. The port is changed back to 400, the
IP packet checksum is recalculated, and the IP packet is sent to Workstation A on the Netopia R2121s LAN
interface.
The reasons for the IP address changes are obvious from the diagram above but what is not so obvious is why
the TCP or UDP source ports need to be changed as well. These are changed and maintained in an internal
table so the Netopia R2121 can determine which host on the local LAN interface sent the IP packet and what
host the response from the WAN interface is going to go to on the LAN interface. This becomes especially
important when two or more hosts on the LAN interface are accessing the same type of service on the Internet,
like a WWW Server (Port 80), for example.
Now look at how two hosts on the LAN interface accessing the same WWW Server on the Internet will work:
Download from Www.Somanuals.com. All Manuals Search And Download.
D-4 User’s Reference Guide
Netopia Router
LAN: 192.168.5.1
WAN: 200.1.1.40
WWW Server
163.176.4.32
Workstations
A & B
ISP Router
200.1.1.1
Netopia
Router
Wkstn A to Netopia
ISP Router to WWW
Src IP: 200.1.1.40
Dst IP: 163.176.4.32
Src Port:: 5001
Netopia to ISP Router
Src IP: 200.1.1.40
Dst IP: 163.176.4.32
Src Port:: 5001
Src IP: 192.168.5.2
Dst IP: 163.176.4.32
Src Port:: 400
Dst Port:: 80
Dst Port:: 80
Dst Port:: 80
Wkstn B to Netopia
Src IP: 192.168.5.3
Dst IP: 163.176.4.32
Src Port:: 400
Netopia to ISP Router
Src IP: 200.1.1.40
Dst IP: 163.176.4.32
Src Port:: 5002
ISP Router to WWW
Src IP: 200.1.1.40
Dst IP: 163.176.4.32
Src Port:: 5002
Dst Port:: 80
Dst Port:: 80
Dst Port:: 80
WWW to ISP Router
Src IP: 163.176.4.32
Dst IP: 200.1.1.40
Src Port:: 80
ISP Router to Netopia
Src IP: 163.176.4.32
Dst IP: 200.1.1.40
Src Port:: 80
Netopia to Wkstn B
Src IP: 163.176.4.32
Dst IP: 192.168.5.3
Src Port:: 80
Dst Port:: 5002
Dst Port:: 5002
Dst Port:: 400
WWW to ISP Router
Src IP: 163.176.4.32
Dst IP: 200.1.1.40
Src Port:: 80
ISP Router to Netopia
Src IP: 163.176.4.32
Dst IP: 200.1.1.40
Src Port:: 80
Netopia to Wkstn A
Src IP: 163.176.4.32
Dst IP: 192.168.5.2
Src Port:: 80
Dst Port:: 5001
Dst Port:: 5001
Dst Port:: 400
As you can see, when Workstation A and Workstation B transmit an IP packet to the WWW Server on the
Internet, they have unique source IP addresses on the LAN interface but potentially the same source ports,
which in this case is 400. When the Netopia R2121 receives these packets, the source IP addresses are
substituted with the single globally unique IP address that was acquired on the WAN interface which is
200.1.1.40.
Now both IP packets have the exact same source IP address (200.1.1.40) and source ports (400). The way the
Netopia R2121 is then able to distinguish between the two IP packets is to change the source TCP or UDP
ports and keep this information in an internal table. As seen above, the source port for Workstation A has been
changed to 5001 and the source port for Workstation B has been changed to 5002.
If you were to look at the internal port mapping table that is maintained by the Netopia R2121, it would look
similar to the following:
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding Netopia NAT Behavior D-5
Source LAN IP
192.168.5.2
192.168.5.3
Source LAN Port
TCP 400
TCP 400
Remapped LAN Port
TCP 5001
TCP 5002
With this information the Netopia R2121 can determine the appropriate routing for an IP response from the
Internet. In this case when the WWW Server responds with a destination port of 5001, the Netopia R2121 can
see that this packet's destination on the local LAN interface is actually Workstation A at IP address
192.168.5.2. Likewise with the response for port 5002, the Netopia R2121 can see that this packet's
destination on the local LAN interface is actually Workstation B at IP address 192.168.5.3.
Exported services
Note that this “automatic” port remapping and IP address substitution only works in one direction, for IP
packets that originated on the LAN interface destined to the WAN interface and the Internet. In order for port
remapping and IP address substitution to work in the other direction, that is, hosts on the Internet wishing to
originate an IP packet destined to a host on the Netopia R2121s LAN interface, a manual redirection of TCP or
UDP ports as well as destination IP addresses within the Netopia R2121 is required. This manual port
remapping and IP address substitution is accomplished by setting up Exported Services.
Exported Services are essentially user defined pointers for a particular type of incoming TCP or UDP service
from the WAN interface to a host on the local LAN interface. This is necessary since the Netopia R2121 and
thus the attached local LAN has only one IP presence on the WAN interface and Internet. Exported Services
allows the user to redirect one type of service, for example Port 21 (FTP), to a single host on the local LAN
interface. This will then allow the Netopia R2121 to redirect any packets coming in from the Internet with the
defined destination TCP or UDP port of Port 21 (FTP) to be redirected to a host on the local LAN interface.
For example, suppose the WWW Server on the Internet with the IP address of 163.176.4.32 wants to access
Workstation B on the Netopia R2121s local LAN interface which is operating as an FTP Server. The IP address
for Workstation B is 192.168.5.3, which is not a valid IP address and thus the WWW Server on the Internet can
not use this IP address to access Workstation B.
The WWW Server on the Internet would then have to use the single valid IP address that was acquired on the
Netopia R2121's WAN interface to access any host on the Netopia R2121's local LAN interface, since this is
the only valid address for the Internet. But if the WWW Server on the Internet opens a connection to
200.1.1.40 via Port 21 (FTP) and no Exported Services are defined on the Netopia R2121, the Netopia R2121
will discard the incoming packet since the Netopia R2121 itself does not perform the requested service.
Thus you can see why Exported Services are necessary. In the example above, an Exported Service needs to
be defined within the Netopia R2121 redirecting any incoming IP traffic with a destination port of 21 to the host
on the local LAN interface with the IP address of 192.168.5.3.
If the WWW Server on the Internet then tries to open a connection to the IP address of 200.1.1.40 with the
appropriate Exported Service defined, the Netopia R2121 will look at the destination port and will find that it is
destined for Port 21 (FTP). The Netopia R2121 then looks at the internal user-defined Exported Services table
and finds that any incoming IP traffic from the WAN port with a destination of Port 21 (FTP) should be redirected
to the IP address of 192.168.5.3 on the local LAN interface, which in this case is Workstation B.
Once the appropriate Exported Services are defined, there can be seamless communication between a host on
the Internet and a host on the Netopia R2121’s local LAN interface.
Download from Www.Somanuals.com. All Manuals Search And Download.
D-6 User’s Reference Guide
Important notes
Even with the advantages of NAT, there are several things you should note carefully:
■
There is no formally agreed upon method among router vendors to handle an all-zeros IPCP request. The
majority of router vendors use the all-zeros IPCP request to determine when a dial-in host wants to be
assigned an IP address. Some vendors however attempt to negotiate and establish routing with an
all-zeros IP address. The Netopia R2121 will not allow routing to be established with an all-zeros IP
address and the call will be dropped with an error logged in the Device Event History.
■
When using NAT it is most likely that the Netopia R2121 will be receiving an IP address from a “pool” of
dynamic IP addresses at the ISP. This means that the Netopia R2121's IP presence on the Internet will
change with each connection. This can potentially cause problems with devices on the Internet attempting
to access services like WWW and FTP servers or AURP partners on the Netopia R2121’s local LAN
interface. In this case, if a dynamic IP address is assigned to the WAN interface of the Netopia R2121
each time, the administrator of the Netopia R2121 will have to notify clients wishing to access services on
the Netopia R2121’s LAN interface of the new IP address after each connection.
■
■
With NAT enabled, there cannot be two or more of the same types of service accessible from the Internet
on the LAN interface of the Netopia R2121. For example, there cannot be multiple FTP servers (Port 23) on
the Netopia R2121's LAN interface that can be accessible by workstations on the Internet. This is due to
the fact that within the Netopia R2121 and IP there is no way to distinguish between multiple servers using
the same port, in this case port 23.
Fictional IP addresses may be assigned on the Netopia R2121’s LAN interface. It is strongly recommended
that for the Netopia R2121’s LAN interface, an IP address from the Class C address range of 192.168.X.X
be used. This is because this range is defined by the IANA as an address space that will never be routed
through the Internet and is to be used by private Intranets not attached to the Internet.
If the address range of 192.168.X.X is not used and another range of addresses such as 100.1.1.X is
used instead, this address space can potentially overlap an address space that is owned by a user
attached to the Internet. Thus if a user on the Netopia R2121’s LAN interface has an IP address of
100.1.1.2 while the Netopia R2121’s LAN interface is 100.1.1.2 and the local host wishes to access a
host on the Internet with the address of 100.1.1.8, the Netopia R2121 has no way of knowing that the
200.1.1.8 address is actually on the Internet and not on its local LAN interface, as the local LAN interface
is assigned the IP address range of 200.1.1.1 to 200.1.1.14.
Configuration
Network Address Translation is enabled by default with the SmartStart configuration utility. You can toggle
Enable Address Translation to NO or YES in the Connection Profile screen in System Configuration under the IP
Profile Parameters section. NAT is enabled on a per-profile basis, so it is possible to have any combination of
NAT and non-NAT profiles. An example of enabling NAT is as follows:
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding Netopia NAT Behavior D-7
IP Profile Parameters
127.0.0.2
Remote IP Address:
Remote IP Mask:
255.255.255.0
Address Translation Enabled:
Yes
Filter Set...
Remove Filter Set
Receive RIP:
No
Enter the remote IP network's IP address (form xxx.xxx.xxx.xxx decimal).
Configure IP requirements for a remote network connection here.
Toggling Address Translation Enabled to Yes enables the Netopia R2121 to send out an all-zeros IPCP address
that requests an IP to be assigned to the Netopia R2121’s WAN interface. Note that the remote IP address is
127.0.0.2, which should also be the Default Gateway under IP Setup in System Configuration. This is done for
profile matching purposes and because the IP address of the router the Netopia R2121 is dialing is not always
known.
As mentioned earlier in this appendix, NAT works well for IP sessions originated on the Netopia R2121’s LAN
interface destined for the Internet without any additional configuration. For incoming IP connections from the
Internet to a host on the Netopia R2121’s LAN interface, Exported Services need to be used.
Exported Services are configured under IP Setup in System Configuration. This is where a particular type of TCP
or UDP service originating from the Internet is redirected to a host on the Netopia R2121’s LAN interface. An
example of this screen is as follows:
Download from Www.Somanuals.com. All Manuals Search And Download.
D-8 User’s Reference Guide
Add Exported Service
+-Type------Port--+
+-----------------+
Service...
| ftp
21
23
25
69
70
79
|
|
|
|
|
|
|
| telnet
| smtp
| tftp
| gopher
| finger
Local Server's IP Address:
| www-http 80
| pop2
| pop3
| snmp
109 |
110 |
161 |
| timbuktu 407 |
| pptp
| irc
| Other...
1723 |
6667 |
|
+-----------------+
ADD EXPORT NOW
CANCEL
Within Exported Services is a pop-up containing a list of well known TCP and UDP services that can be
redirected to a single host on the Netopia R2121’s LAN interface. There is also an “Other...” option which
allows for manual configuration of additional TCP or UDP ports. There can be a total of 32 Exported Services
that can be defined.
When a particular type of service is redirected to an IP address, that service is removed from the pop-up list,
since only one type of service can be redirected to a single host. However several different types of services
can be redirected to a single or multiple hosts. For example, port 80 (WWW Server) could be redirected to
192.168.5.3 on the Netopia R2121’s LAN interface as well as port 23 (Telnet) can be redirected to that same
host.
Summary
NAT is a powerful feature of the Netopia R2121 and when used and set up properly can yield a secure network
while only using one IP address on the WAN interface. Note that the addresses listed in this appendix are for
demonstration purposes only. Do not use these addresses when configuring your local network.
Download from Www.Somanuals.com. All Manuals Search And Download.
Binary Conversion Table E-1
Appendix E
Binary Conversion Table
This table is provided to help you choose subnet numbers and host numbers for IP and MacIP networks that
use subnetting for IP addresses.
Decimal
Binary
Decimal
Binary
Decimal
Binary
1000000
1000001
1000010
1000011
1000100
1000101
1000110
1000111
1001000
1001001
1001010
1001011
1001100
1001101
1001110
1001111
1010000
1010001
1010010
1010011
1010100
1010101
1010110
1010111
1011000
1011001
1011010
1011011
1011100
1011101
1011110
1011111
Decimal
Binary
1100000
1100001
1100010
1100011
1100100
1100101
1100110
1100111
1101000
1101001
1101010
1101011
1101100
1101101
1101110
1101111
1110000
1110001
1110010
1110011
1110100
1110101
1110110
1110111
1111000
1111001
1111010
1111011
1111100
1111101
1111110
1111111
0
1
2
3
4
5
6
7
8
9
0
32
100000
64
96
1
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
1000001
100010
100011
100100
100101
100110
100111
101000
101001
101010
101011
101100
101101
101110
101111
110000
110001
110010
110011
110100
110101
110110
110111
111000
111001
111010
111011
111100
111101
111110
111111
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
97
10
11
98
99
100
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
101
110
111
1000
1001
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
1010
1011
1100
1101
1110
1111
10000
10001
10010
10011
10100
10101
10110
10111
11000
11001
11010
11011
11100
11101
11110
11111
Download from Www.Somanuals.com. All Manuals Search And Download.
E-2 User’s Reference Guide
Decimal
Binary
10000000
10000001
10000010
10000011
10000100
10000101
10000110
10000111
10001000
10001001
10001010
10001011
10001100
10001101
10001110
10001111
10010000
10010001
10010010
10010011
10010100
10010101
10010110
10010111
10011000
10011001
10011010
10011011
10011100
10011101
10011110
10011111
Decimal
Binary
10100000
10100001
10100010
10100011
10100100
10100101
10100110
10100111
10101000
10101001
10101010
10101011
10101100
10101101
10101110
10101111
10110000
10110001
10110010
10110011
10110100
10110101
10110110
10110111
10111000
10111001
10111010
10111011
10111100
10111101
10111110
10111111
Decimal
Binary
11000000
11000001
11000010
11000011
11000100
11000101
11000110
11000111
11001000
11001001
11001010
11001011
11001100
11001101
11001110
11001111
11010000
11010001
11010010
11010011
11010100
11010101
11010110
11010111
11011000
11011001
11011010
11011011
11011100
11011101
11011110
11011111
Decimal
Binary
11100000
11100001
11100010
11100011
11100100
11100101
11100110
11100111
11101000
11101001
11101010
11101011
11101100
11101101
11101110
11101111
11110000
11110001
11110010
11110011
11110100
11110101
11110110
11110111
11111000
11111001
11111010
11111011
11111100
11111101
11111110
11111111
128
160
192
224
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
Download from Www.Somanuals.com. All Manuals Search And Download.
Further Reading F-1
Appendix F
Further Reading
Angell, David. ISDN for Dummies, Foster City, CA: IDG Books Worldwide, 1995. Thorough introduction to ISDN
for beginners.
Apple Computer, Inc. AppleTalk Network System Overview. Reading, Massachusetts: Addison-Wesley Publishing
Company, Inc.; 1989.
Apple Computer, Inc. Planning and Managing AppleTalk Networks. Reading, Massachusetts: Addison-Wesley
Publishing Company, Inc.; 1991.
Black, U. Data Networks: Concepts, Theory and Practice. Englewood Cliffs, New Jersey: Prentice Hall; 1989.
Black, U. Physical Level Interfaces and Protocols. Los Alamitos, California: IEEE Computer Society Press; 1988.
Black, Uyless. Emerging Communications Technologies, Englewood Cliffs, New Jersey: PTR Prentice Hall, 1994.
Describes how emerging communications technologies, including ISDN and Frame Relay operate and where
they fit in a computer/ communications network.
Case, J.D., J.R. Davins, M.S. Fedor, and M.L. Schoffstall. "Network Management and the Design of SNMP."
ConneXions: The Interoperability Report, Vol. 3: March 1989.
Case, J.D., J.R. Davins, M.S. Fedor, and M.L. Schoffstall. "Introduction to the Simple Gateway Monitoring
Protocol." IEEE Network: March 1988."
Chapman, D. Brent and Elizabeth D. Zwicky. Building Internet Firewalls, Sebastopol, CA: O’Reilly & Associates,
1995. Dense and technical, but Chapter 6 provides a basic introduction to packet filtering.
Chapman, D. Brent. “Network (In)Security Through IP Packet Filtering,” paper available from Great Circle
Associates, 1057 West Dana Street, Mountain View, CA 94041
Chappell, L. Novell's Guide to NetWare LAN Analysis. San Jose, California: Novell Press; 1993.
Clark, W. "SNA Internetworking." ConneXions: The Interoperability Report, Vol. 6, No. 3: March 1992.
Coltun, R. "OSPF: An Internet Routing Protocol." ConneXions: The Interoperability Report, Vol. 3, No. 8: August
1989.
Comer, D.E. Internetworking with TCP/ IP: Principles, Protocols, and Architecture, Vol. I, 2nd ed. Englewood
Cliffs, New Jersey: Prentice Hall; 1991.
Davidson, J. An Introduction to TCP/ IP. New York, New York: Springer-Verlag; 1992.
Ferrari, D. Computer Systems Performance Evaluation. Englewood Cliffs, New Jersey: Prentice Hall; 1978.
Garcia-Luna-Aceves, J.J. "Loop-Free Routing Using Diffusing Computations." Publication pending in IEEE/ ACM
Transactions on Networking, Vol. 1, No. 1, 1993.
Garfinkel, Simson. PGP: Pretty Good Privacy, Sebastopol, CA: O’Reilly & Associates, 1991. A guide to the free
data encryption program PGP and the issues surrounding encryption.
Green, J.K. Telecommunications, 2nd ed. Homewood, Illinois: Business One Irwin; 1992.
Hagans, R. "Components of OSI: ES-IS Routing." ConneXions: The Interoperability Report, Vol. 3, No. 8: August
1989.
Download from Www.Somanuals.com. All Manuals Search And Download.
F-2 User’s Reference Guide
Hares, S. "Components of OSI: Inter-Domain Routing Protocol (IDRP)." ConneXions: The Interoperability Report,
Vol. 6, No. 5: May 1992.
Jones, N.E.H. and D. Kosiur. Macworld Networking Handbook. San Mateo, California: IDG Books Worldwide,
Inc.; 1992.
Joyce, S.T. and J.Q. Walker II. "Advanced Peer-to-Peer Networking (APPN): An Overview." ConneXions: The
Interoperability Report, Vol. 6, No. 10: October 1992.
Kousky, K. "Bridging the Network Gap." LAN Technology, Vol. 6, No. 1: January 1990.
LaQuey, Tracy. The Internet Companion: A Beginner's Guide to Global Networking, Reading, Massachusetts:
Addison-Wesley Publishing Company, Inc.; 1994.
Leinwand, A. and K. Fang. Network Management: A Practical Perspective. Reading, Massachusetts:
Addison-Wesley Publishing Company, Inc.; 1993.
Levine, John R. and Carol Baroudi. The Internet for Dummies, Foster City, CA: IDG Books Worldwide, 1993.
Covers all of the most popular Internet services, including e-mail, newsgroups, and the World Wide Web. Also
has information on setting up individual workstations with TCP/ IP stacks.
Lippis, N. "The Internetwork Decade." Data Communications, Vol. 20, No. 14: October 1991.
McNamara, J.E. Local Area Networks. Digital Press, Educational Services, Digital Equipment Corporation, 12
Crosby Drive, Bedford, MA 01730.
Malamud, C. Analyzing DECnet/ OSI Phase V. New York, New York: Van Nostrand Reinhold; 1991.
Malamud, C. Analyzing Novell Networks. New York, New York: Van Nostrand Reinhold; 1991.
Malamud, C. Analyzing Sun Networks. New York, New York: Van Nostrand Reinhold; 1991.
Martin, J. SNA: IBM's Networking Solution. Englewood Cliffs, New Jersey: Prentice Hall; 1987.
Martin, J., with K.K. Chapman and the ARBEN Group, Inc. Local Area Networks. Architectures and Implementa-
tions. Englewood Cliffs, New Jersey: Prentice Hall; 1989.
Medin, M. "The Great IGP Debate--Part Two: The Open Shortest Path First (OSPF) Routing Protocol."
ConneXions: The Interoperability Report, Vol. 5, No. 10: October 1991.
Meijer, A. Systems Network Architecture: A tutorial. New York, New York: John Wiley & Sons, Inc.; 1987.
Miller, A. Mark. Analyzing Broadband Networks (Frame Relay, SMDS, & ATM), M&T Books: A Division of MIS:
Press, 1994. An intermediate/ advanced reference on Frame Relay technologies.
Miller, M.A. Internetworking: A Guide to Network Communications LAN to LAN; LAN to WAN, 2nd. ed. San Mateo,
California: M&T Books; 1992.
Miller, M.A. LAN Protocol Handbook. San Mateo, California: M&T Books; 1990.
Miller, M.A. LAN Troubleshooting Handbook. San Mateo, California: M&T Books; 1989.
O'Reilly, T. and G. Todino. Managing UUCP and Usenet, 10th ed. Sebastopol, California: O'Reilly & Associates,
Inc.; 1992.
Perlman, R. Interconnections: Bridges and Routers. Reading, Massachusetts: Addison-Wesley Publishing
Company, Inc.; 1992.
Perlman, R. and R. Callon. "The Great IGP Debate--Part One: IS-IS and Integrated Routing." ConneXions: The
Interoperability Report, Vol. 5, No. 10: October 1991.
Download from Www.Somanuals.com. All Manuals Search And Download.
Further Reading F-3
Rose, M.T. The Open Book: A Practical Perspective on OSI. Englewood Cliffs, New Jersey: Prentice Hall; 1990.
Rose, M.T. The Simple Book: An Introduction to Management of TCP/ IP-based Internets. Englewood Cliffs, New
Jersey: Prentice Hall; 1991.
Ross, F.E. "FDDI--A Tutorial." IEEE Communications Magazine, Vol. 24, No. 5: May 1986.
Schlar, S.K. Inside X.25: A Manager's Guide. New York, New York: McGraw-Hill, Inc.; 1990.
Schwartz, M. Telecommunications Networks: Protocols, Modeling, and Analysis. Reading, Massachusetts:
Addison-Wesley Publishing Company, Inc.; 1987.
Sherman, K. Data Communications: A User's Guide. Englewood Cliffs, New Jersey: Prentice Hall; 1990.
Sidhu, G.S., R.F. Andrews, and A.B. Oppenheimer. Inside AppleTalk, 2nd ed. Reading, Massachusetts:
Addison-Wesley Publishing Company, Inc.; 1990.
Siyan, Karanjit. Internet Firewall and Network Security, Indianapolis: New Riders Publishing, 1995. Similar to the
Chapman and Zwicky book.
Smith, Philip. Frame Relay Principles and Applications, Addison-Wesley Publishing Company, 1996. Covers
information on Frame Relay, including the pros and cons of the technology, description of the theory and
application, and an explanation of the standardization process.
Spragins, J.D. et al. Telecommunications Protocols and Design. Reading, Massachusetts: Addison-Wesley
Publishing Company, Inc.; 1991.
Stallings, W. Data and Computer Communications. New York, New York: Macmillan Publishing Company; 1991.
Stallings, W. Handbook of Computer-Communications Standards, Vols. 1-3. Carmel, Indiana: Howard W. Sams,
Inc.; 1990.
Stallings, W. Local Networks, 3rd ed. New York, New York: Macmillan Publishing Company; 1990.
Stevens, W.R. TCP/ IP Illustrated, Vol 1. Reading, Massachusetts: Addison-Wesley Publishing Company, Inc.;
1994.
Sunshine, C.A. (ed.). Computer Network Architectures and Protocols, 2nd ed. New York, New York: Plenum
Press; 1989.
Tannenbaum, A.S. Computer Networks, 2nd ed. Englewood Cliffs, New Jersey: Prentice Hall; 1988.
Terplan, K. Communication Networks Management. Englewood Cliffs, New Jersey: Prentice Hall; 1992.
Tsuchiya, P. "Components of OSI: IS-IS Intra-Domain Routing." ConneXions: The Interoperability Report, Vol. 3,
No. 8: August 1989.
Tsuchiya, P. "Components of OSI: Routing (An Overview)." ConneXions: The Interoperability Report, Vol. 3, No.
8: August 1989.
Zimmerman, H. "OSI Reference Model--The ISO Model of Architecture for Open Systems Interconnection." IEEE
Transactions on Communications COM-28, No. 4: April 1980.
Download from Www.Somanuals.com. All Manuals Search And Download.
F-4 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications and Safety Information G-1
Appendix G
Technical Specifications and Safety Information
Pinouts for Auxiliary Port Modem Cable
1300 ohms
1
1
2
2
3
3
4
5
4
5
6
6
7
7
8
8
9
9
10
11
12
13
14
15
Shield
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Shield
BRAID
HD-15
DB-25
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Ground
TDA
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
(not used)
TD
TDB
RD
RDA
RTS
RDB
CTS
(not used)
DTR
DCE Ready
Ground
RLSD
CTS
Download from Www.Somanuals.com. All Manuals Search And Download.
G-2 User’s Reference Guide
HD-15
DB-25
Pin 9
DSR
DCD
Pin 9
-RSET (EIA-530)
(not used)
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
Pin 16
Pin 17
Pin 18
Pin 19
Pin 20
Pin 21
Pin 22
Pin 23
Pin 24
Pin 25
(not used)
TCA
-TSET (EIA-530)
(not used)
TCB
(not used)
RCA
-TD (EIA-530) STD (EIA-232)
(not used)
RCB
-RD (EIA-530) SRD (EIA-232)
RSET
(not used)
-RTS (EIA-530) SRTS (EIA-232)
DTE Ready
(not used)
(not used)
Ground
TSET
(not used)
Note: Certain RS-232 modems do not properly accept signals on pins 12/ 24, 13/ 11,
14/ 17, and 15/ 9. For these applications, these pins may need to be cut.
Description
Dimensions: 124.0 cm (w) x 20.0 cm (d) x 5.3 cm (h)
9.4” (w) x 7.9” (d) x 2.1” (h)
Communications interfaces: The Netopia R2121 Dual Analog Router has two RJ-45 jacks for modem
connections; an 8 port 10Base-T Ethernet hub for your LAN connection; a DE-9 Console port; and an HD-15
Auxiliary port that can be used as either a serial or LocalTalk port.
56K Modem Specifications: complies with ITU-T V.90 and/ or K56flex standard
Power requirements
■
12 VDC input
■
1.5 Amps
Environment
Operating temperature: 0° to +40° C
Storage temperature: 0° to +70° C
Relative storage humidity: 20 to 80% non-condensing
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications and Safety Information G-3
Software and protocols
Software media: Software preloaded on internal flash memory; field upgrades done via download to internal
flash memory via XMODEM or TFTP
Routing: TCP/ IP Internet Protocol Suite, RIP, AppleTalk*, LocalTalk-to-Ethernet routing*, AURP tunneling*,
MacIP*, IPX
* optional add-on feature
WAN support: PPP, MP, HDLC
Security: PAP, CHAP, PAP-TOKEN, CACHE-TOKEN, callback, SecurID, IP/ IPX firewalls, UI password security, and
CallerID
SNMP network management: SNMPv1, MIB-II (RFC 1213), Interface MIB (RFC 1229), Ethernet MIB (RFC
1643), AppleTalk MIB-I (1243), Netopia R2121 MIB
Management/ configuration methods: HTTP (web server), serial console, remote modem console, telnet,
SNMP
Diagnostics: PING, event logging, routing table displays, traceroute, statistics counters, Call Accounting
Agency approvals
The Netopia R2121 Dual Analog Router has met the safety standards (per CSA-950) of the Canadian Standards
Association for Canada.
The Netopia R2121 Dual Analog Router has met the safety standards (per UL-1950) of the Underwriters
Laboratories for United States.
Regulatory notices
Warning
This is a Class A product. In a domestic environment this product may cause radio interference, in which case
the user may be required to take adequate measures. Adequate measures include increasing the physical
distance between this product and other electrical devices.
United States. This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
FCC Requirements, Part 68. The Federal Communications Commission (FCC) has established Rules which
permit this device to be directly connected to the telephone network. Standardized jacks are used for these
connections. This equipment should not be used on party lines or coin phones.
Download from Www.Somanuals.com. All Manuals Search And Download.
G-4 User’s Reference Guide
If this device is malfunctioning, it may also be causing harm to the telephone network; this device should be
disconnected until the source of the problem can be determined and until repair has been made. If this is not
done, the telephone company may temporarily disconnect service.
The telephone company may make changes in its technical operations and procedures; if such changes affect
the compatibility or use of this device, the telephone company is required to give adequate notice of the
changes. You will be advised of your right to file a complaint with the FCC.
If the telephone company requests information on what equipment is connected to their lines, inform them of:
a) The telephone number to which this unit is connected.
b) The ringer equivalence number
c) The USOC jack required. (RJ11C)
d) The FCC Registration Number. (14 digits provided by FCC)
Items (b) and (d) are indicated on the label. The Ringer Equivalence Number (REN) is used to determine how
many devices can be connected to your telephone line. In most areas, the sum of the REN's of all devices on
any one line should not exceed five (5.0). If too many devices are attached, they many not ring properly.
Service Requirements. In the event of equipment malfunction, all repairs should be performed by our Company
or an authorized agent. Under FCC rules, no customer is authorized to repair this equipment. This restriction
applies regardless of whether the equipment is in or our of warranty. It is the responsibility of users requiring
service to report the need for service to our Company or to one of our authorized agents. Service can be
obtained at Netopia, Inc., 2470 Mariner Square Loop, Alameda, California, 94501.
Important
This product was tested for FCC compliance under conditions that included the use of shielded cables and
connectors between system components. Changes or modifications to this product not authorized by the
manufacturer could void your authority to operate the equipment.
Canada. This digital apparatus does not exceed the Class A limits for radio noise emission from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe A prescrites dans le Réglement sur le brouillage radioélectrique édicté par le
ministère des Communications du Canada.
Declaration for Canadian users
The Canadian Industry Canada label identifies certified equipment. This certification means that the equipment
meets certain telecommunications network protective, operation and safety requirements. The Department
does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of
the local telecommunications company. The equipment must also be installed using an acceptable method of
connection. In some cases, the company’s inside wiring associated with a single line individual service may be
extended by means of a certified connector assembly (telephone extension cord.) The customer should be
aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to the certified equipment should be made by an authorized Canadian maintenance facility designated
by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may
give the telecommunications company cause to request the user to disconnect the equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications and Safety Information G-5
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
Caution
Users should not attempt to make such connections themselves, but should contact the appropriate electric
inspection authority, or electrician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be
connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop
may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of
all the devices does not exceed 100.
Important safety instructions
Caution
■
The direct plug-in power supply serves as the main power disconnect; locate the direct plug-in power supply
near the product for easy access.
■
For use only with CSA Certified Class 2 power supply, rated 12VDC, 1.5A.
Telecommunication installation cautions
■
■
■
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at
the network interface.
■
■
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk
of electric shock from lightning.
■
Do not use the telephone to report a gas leak in the vicinity of the leak.
Battery
The Netopia R2121’s lithium battery is designed to last for the life of the product. The battery is not user-ser-
viceable.
Caution!
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer's instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
G-6 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
About 56K Line Access H-1
Appendix H
About 56K Line Access
The Netopia R2121 with Dual Analog is capable of 56Kbps per line connections. This means that if you use
both onboard modems, you can achieve inbound data transfer rates of up to 112Kbps. Using a third modem
bumps the theoretical speed limit to 168Kbps.
This section describes some practical limitations on the previous statements.
A current FCC limitation will only permit a maximum speed of 52Kbps over analog phone lines using combined
analog/ digital technology. Also, the data transfer rates are for inbound data only. Outbound data is limited to
the current transfer rates for analog phone lines alone which is 33.6Kbps. So, using both onboard modems
under optimal conditions, will yield an inbound data transfer rate of 104Kbps and an outbound rate of
67.2Kbps. This means that your incoming email, file transfers and downloads, web browsing, and so on, occur
at 104Kbps, while your outgoing information, such as outbound email, travels at 67.2Kbps. With a third
modem, the rates become 156Kbps inbound and 100.8Kbps outbound. Also, to achieve the maximum inbound
rates, the ISP-side data must be digitally sourced.
Outbound data
33.6K
67.2K
33.6K
Inbound data
56K
112K
56K
Above a certain threshold (called Shannon's Limit) the signal-to-noise ratio of any medium becomes too low to
reliably transfer data. The analog phone line is the limiting factor in the speed of data transmission because of
the inherent noise it contributes.
Today's telephone network is increasingly digital. In particular, the portion of the phone connection between the
phone company and the Internet Service Provider (ISP) is often digital. Digital lines still have noise, and are still
subject to Shannon's limit, but they have less noise and a higher ceiling.
Several companies have created techniques that take advantage of the digital portion of the phone network to
achieve higher speeds than were possible with a purely analog pathway.
Download from Www.Somanuals.com. All Manuals Search And Download.
H-2 User’s Reference Guide
These new techniques treat the phone system as a mostly digital network that just happens to have an analog
portion. There are several consequences to the reliance on a half-digital connection. Your Internet Service
Provider must have digital phone lines to the public switched telephone network (PSTN). That's the easy part: if
your ISP offers 56Kbps, they have the digital lines.
Getting the most out of 56K technology requires that you have optimal conditions on your telephone line. Any
noise in the line will degrade your connection. Statistics show that most people connect somewhere between
45 and 50K. Many connect at 52K. Connect rates between 40 and 50K are in no way a failure on the part of
the Internet Service Provider, but simply a fact of life in trying to extend the limitations of noisy analog
The Netopia R2121 with Dual Analog ships with the unified ITU V.90 standard firmware, also known as V.PCM,
which merges the K56flex standard with the competing x2 standard. K56flex firmware can be found on the
Netopia CD for XMODEM transfer to the onboard modems, if your ISP supports that technology. Subsequent
modem firmware updates will be made available on the Netopia website. See “Transferring configuration and
firmware files with TFTP,” and “Transferring configuration and firmware files with XMODEM,” in Chapter 15,
“Utilities and Diagnostics.”
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary 1
Glossary
Access Line: A telephone line reaching from the telephone company central office to a point usually on your
premises. Beyond this point the wire is considered inside wiring. See also Trunk Line.
analog: In telecommunications, telephone transmission and/ or switching that is not digital. An analog phone
transmission is one that was originally intended to carry speech or voice, but may with appropriate
modifications be used to carry data of other types.
ANSI (American National Standards Institute): Devises and proposes recommendations for international
communications standards. See also Comite Consultatif International Telegraphique et Telephonique (CCITT).
AppleTalk: A comprehensive network system designed and developed by Apple Computer, Inc. AppleTalk
allows many different types of computer systems, printers, and servers to communicate on a variety of cabling
schemes, including LocalTalk and Ethernet cabling. In this manual, AppleTalk refers especially to the protocols
or rule sets that govern this communication.
AppleTalk address: A unique identifier for each device using AppleTalk that allows information to be sent and
received correctly. An AppleTalk address always includes a network number wherever two or more AppleTalk
networks are connected together by routers.
AURP (Apple Update-based Router Protocol): An enhanced AppleTalk routing protocol. AURP provides
improved support for AppleTalk over wide area networks (WANs) and tunneling through non-AppleTalk (IP)
networks. AURP features include network number remapping, clustering of remote network numbers, and hop
count reduction.
backbone: A network topology consisting of a single length of cable with multiple network connection points.
Bandwidth: The range of frequencies, expressed in Kilobits per second, that can pass over a given data
transmission channel within a network. The bandwidth determines the rate at which information can be sent
through a channel - the greater the bandwidth, the more information that can be sent in a given amount of time.
BAP: Bandwidth Allocation Protocol. Manages the dynamic bandwidth allocation of implementations
supporting the PPP multilink protocol. This is done by defining the Bandwidth Allocation Protocol (BAP),
as well as its associated control protocol, the Bandwidth Allocation Control Protocol (BACP). BAP can be
used to manage the number of links in a multilink bundle.
baud rate: The rate of the signaling speed of a transmission medium.
bit: A binary digit; the smallest unit of data in the binary counting system. A bit has a value of either 0 or 1.
bits per second (bps): A measure of the actual data transmission rate. The bps rate may be equal to or greater
than the baud rate depending on the modulation technique used to encode bits into each baud interval. The
correct term to use when describing modem data transfer speeds.
bps: See bits per second.
branch: A length of cable in a star network that goes from the center of the star to a wall jack.
broadcast: A network transaction that sends data to all hosts connected to the network.
Burstiness: Data that uses bandwidth only sporadically; that is, information that does not use the total
bandwidth of a circuit 100 percent of the time. During pauses, channels are idle; and no traffic flows across
them in either direction. Interactive and LAN-to-LAN data is bursty in nature, because it is sent intermittently,
and in between data transmission the channel experiences idle time waiting for the DTEs to respond to the
transmitted data user’s input of waiting for the user to send more data.
Download from Www.Somanuals.com. All Manuals Search And Download.
2 User’s Reference Guide
byte: A group of bits, normally eight, which represent one data character.
CallerID: See CND.
CCITT (Comite Consultatif International Telegraphique et Telephonique): International Consultative
Committee for Telegraphy and Telephony, a standards organization that devises and proposes recommenda-
tions for international communications. See also ANSI (American National Standards Institute).
CHAP (challenge handshake protocol): A method for ensuring secure network access and communications.
Class A, B, and C networks: The values assigned to the first few bits in an IP network address determine
which class designation the network has. In decimal notation, Class A network addresses range from 1.X.X.X to
126.X.X.X, Class B network addresses range from 128.1.X.X to 191.254.X.X, and Class C addresses range
from 192.0.1.X to 223.255.254.X. For more information on IP network address classes, see Appendix C,
“Understanding IP Addressing.”
client: An intelligent workstation that makes requests to other computers known as servers. PC computers on
a LAN can be clients.
clustering: A feature that clusters remapped network numbers into a range of sequential network numbers.
CNA (Calling Number Authentication): A security feature that will reject an incoming call if it does not match
the Calling Number field in one of the Netopia ISDN Router’s Connection Profiles.
CND (Calling Number Delivery): Also known as caller ID, a feature that allows the Called Customer Premises
Equipment (CPE) to receive a calling party’s directory number during the call establishment phase.
community strings: Sequences of characters that serve much like passwords for devices using SNMP.
Different community strings may be used to allow an SNMP user to gather device information or change device
configurations.
CRC (Cyclic Redundancy Check): A computational means to ensure the integrity of a block of data. The
mathematical function is computed, before the data is transmitted at the originating device. Its numerical value
is computed based on the content of the data. This value is compared with a recomputed value of the function
at the destination device.
DCE (Data Communications Equipment): Term defined by standards committees, that applies to
communications equipment, typically modems or printers, as distinct from other devices that attach to the
network, typically personal computers or data terminals (DTE). The distinction generally refers to which pins in
an RS-232-C connection transmit or receive data. Also see DTE.
DDP (Datagram Delivery Protocol): Defines socket-to-socket delivery of datagrams over an AppleTalk internet.
DTE (Data Terminal Equipment): Term defined by standards committees, that applies to communications
equipment, typically personal computers or data terminals, as distinct from other devices that attach to the
network, typically modems or printers (DCE). The distinction generally refers to which pins in an RS-232-C
connection transmit or receive data. Pins 2 and 3 are reversed. Also see DCE.
default zone: When a Phase II EtherTalk network includes more than one zone, all routers on that network
must be configured to assign one of these zones as a default zone. The default zone is temporarily assigned to
any Phase II EtherTalk node that hasn’t chosen a zone. The user may choose another zone by opening the
Network Control Panel, selecting the correct physical connection, and then choosing a zone in the scrolling field
displayed.
DHCP (Dynamic Host Configuration Protocol): A service that lets clients on a LAN request configuration
information, such as IP host addresses, from a server.
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary 3
DNS (Domain Name Service): A TCP/ IP protocol for discovering and maintaining network resource information
distributed among different servers.
download: The process of transferring a file from a server to a client.
EIA (Electronic Industry Association): A North American standards association.
Ethernet: A networking protocol that defines a type of LAN characterized by a 10 Mbps (megabits per second)
data rate. Ethernet is used in many mainframe, PC, and UNIX networks, as well as for EtherTalk.
Ethernet address: Sometimes referred to as a hardware address. A 48-bits long number assigned to every
Ethernet hardware device. Ethernet addresses are usually expressed as 12-character hexadecimal numbers,
where each hexadecimal character (0 through F) represents four binary bits. Do not confuse the Ethernet
address of a device with its network address.
EtherTalk: Apple’s data-link software that allows an AppleTalk network to be connected by Ethernet cables.
EtherTalk is a protocol within the AppleTalk protocol set. Two versions of EtherTalk are in common use,
designated as Phase I and Phase II EtherTalk.
extended network: A network using AppleTalk Phase II protocols; EtherTalk 2.0 and TokenTalk are extended
networks. LocalTalk networks are compatible with Phase II but are not extended because a single LocalTalk
network cannot have multiple network numbers or multiple zone names.
firmware: System software stored in a device’s memory that controls the device. The Netopia ISDN Router’s
firmware can be updated.
gateway: A device that connects two or more networks that use different protocols. Gateways provide address
translation services, but do not translate data. Gateways must be used in conjunction with special software
packages that allow computers to use networking protocols not originally designed for them.
hard seeding: A router setting. In hard seeding, if a router that has just been reset detects a network number
or zone name conflict between its configured information and the information provided by another router, it
disables the router port for which there is a conflict. See also non-seeding, seeding, seed router, and soft
seeding.
HDLC (High Level Data Link Control): A generic link-level communications protocol developed by the
International Organization for Standardization (ISO). HDLC manages synchronous, code-transparent, serial
information transfer over a link connection. See also SDLC (Synchronous Data Link Control).
header: In packets, a header is part of the envelope information that surrounds the actual data being
transmitted. In e-mail, a header is usually the address and routing information found at the top of messages.
hop: A single traverse from one node to another on a LAN.
hop count: The number of nodes (routers or other devices) a packet has gone through. If there are six routers
between source and destination nodes, the hop count for the packet will be six when it arrives at its destination
node. The maximum allowable hop count is usually 15.
hop count reduction: A feature of AURP supported by the Netopia ISDN Router. Tunnels and point-to-point
links over WANs can often exceed the maximum allowable hop count of 15 routers. Network administrators can
use the hop count reduction feature to set up tunnels and point-to-point links that exceed the 15-router limit.
host: A single, addressable device on a network. Computers, networked printers, and routers are hosts.
Host Computer: A communications device that enables users to run applications programs to perform such
functions as text editing, program execution, access to data bases, etc.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 User’s Reference Guide
internet: A set of networks connected together by routers. This is a general term, not to be confused with the
large, multi-organizational collection of IP networks known as the Internet. An internet is sometimes also known
as an internetwork.
internet address, IP address: Any computing device that uses the Internet Protocol (IP) must be assigned an
internet or IP address. This is a 32-bit number assigned by the system administrator, usually written in the form
of 4 decimal fields separated by periods, e.g., 192.9.200.1. Part of the internet address is the IP network
number (IP network address), and part is the host address (IP host address). All machines on a given IP
network use the same IP network number, and each machine has a unique IP host address. The system
administrator sets the subnet mask to specify how much of the address is network number and how much is
host address. See also Class A, B, and C networks.
IP (Internet Protocol): A networking protocol developed for use on computer systems that use the UNIX
operating system. Often used with Ethernet cabling systems. In this manual, IP is used as an umbrella term to
cover all packets and networking operations that include the use of the Internet Protocol. See also TCP/ IP.
IP address, IP host address, IP network address: See internet address.
IP broadcast: See broadcast.
IP tunneling: See AURP.
IPX (Internet Package Exchange): A protocol used by Novell Netware networks.
ISDN (Integrated Services Digital Network): A method of transmitting data digitally over telephone lines.
ISP (Internet service provider): A company that provides Internet-related services. Most importantly, an ISP
provides Internet access services and products to other companies and consumers.
ITU (International Telecommunication Union): United Nations specialized agency for telecommunications.
Successor to CCITT.
K56flex: A modem data transmission technology standard created by Lucent Technologies and Rockwell
International. Its purpose is to take advantage of the largely digital portions of the telephone system in order to
exceed the theoretical speed limitations of data transmission over analog telephone lines. A competing
technology called “x2,” created by U.S. Robotics/ 3Com, performs a similar function. In February, 1998, the
interested parties agreed on a unified standard called V.90, also known as V.PCM, which merges the K56flex
standard with the competing x2 standard. In September, 1998, the International Telecommunications Union is
expected to ratify the unified standard, thereby allowing interoperability of modems and ISPs’ central site
equipment, with appropriate firmware upgrades.
LAN (Local Area Network): A privately owned network that offers high-speed communications channels to
connect information processing equipment in a limited geographic area.
LocalTalk: The cabling specification for AppleTalk running at a speed of 230.4 kbps (kilobits per second).
MacIP: A protocol in which IP packets are encapsulated within AppleTalk headers, for transmission over
AppleTalk networks. MacIP requires the presence of at least one AppleTalk–IP gateway. MacIP is usually used to
allow an AppleTalk computer to communicate with an IP computer.
MacIP client: A Macintosh computer that is using the MacIP protocol to communicate with an IP computer.
MIB (Management Information Base): A standardized structure for SNMP management information.
modem: A device used to convert digital signals from a computer into analog signals that can be transmitted
across standard analog (not ISDN) telephone lines. Modem is a contraction of modulator-demodulator.
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary 5
NAT (Network Address Translation): A feature that allows communication between the LAN connected to the
Netopia ISDN Router and the Internet using a single IP address, instead of having a separate IP address for
each computer on the network.
NetBIOS: A network communications protocol used on PC LANs.
network: A group of computer systems and other computer devices that communicate with one another.
network administrator: A person who coordinates the design, installation, and management of a network. A
network administrator is also responsible for troubleshooting and for adding new users to the network.
network log: A record of the names of devices, location of wire pairs, wall-jack numbers, and other information
about the network.
network number: A unique number for each network in an internet. AppleTalk network numbers are assigned
by seed routers, to which the network is directly connected. An isolated AppleTalk network does not need a
network number.
network number remapping: Resolves network number conflicts when two or more AppleTalk networks that
may have duplicate network numbers are connected together. The Netopia ISDN Router lets you set up a range
of network numbers into which remote AppleTalk network numbers are remapped.
network range: A unique set of contiguous numbers associated with an extended network; each number in a
network range can be associated with up to 253 node addresses.
node: See host.
non-seeding: A router setting that causes it to request network number and zone information from any other
routers on the network connected to the non-seeding port. If it receives this information, it begins to route
packets through that port. See also hard seeding, seeding, seed router, and soft seeding.
packet: A group of fixed-length binary digits, including the data and call control signals, that are transmitted
through an X.25 packet-switching network as a composite whole. The data, call control signals, and possible
error control information are arranged in a predetermined format. Packets do not always travel the same
pathway but are arranged in proper sequence at the destination side before forwarding the complete message
to an addressee.
Packet-Switching Network: A telecommunications network based on packet-switching technology, wherein a
transmission channel is occupied only for the duration of the transmission of the packet.
PAP (PPP authentication protocol): A method for ensuring secure network access.
Parameter: A numerical code that controls an aspect of terminal and/ or network operation. Parameters
control such aspects as page size, data transmission speed, and timing options.
port: A location for passing data in and out of a device, and, in some cases, for attaching other devices or
cables.
port number: A number that identifies a TCP/ IP-based service. Telnet, for example, is identified with TCP port
23.
POTS (Plain Old Telephone Service): Ordinary analog telephone service such as that used for voice
transmission, as distinct from digital service.
PPP (Point to Point Protocol): A protocol for framing IP packets and transmitting them over a serial line.
protocol: A set of rules for communication, sometimes made up of several smaller sets of rules also called
protocols. AppleTalk is a protocol that includes the LocalTalk, EtherTalk, and TokenTalk protocols.
Download from Www.Somanuals.com. All Manuals Search And Download.
6 User’s Reference Guide
remapping: See network number remapping.
RFC (Request for Comment): A series of documents used to exchange information and standards about the
Internet.
RIP (Routing Information Protocol): A protocol used for the transmission of IP routing information.
RJ-11: A telephone-industry standard connector type, usually containing four pins.
RJ-45: A telephone-industry standard connector type usually containing eight pins.
router: A device that supports network communications. A router can connect identical network types, such as
LocalTalk-to-LocalTalk, or dissimilar network types, such as LocalTalk-to-Ethernet. However—unless a gateway is
available—a common protocol, such as TCP/ IP, must be used over both networks. Routers may be equipped to
provide WAN line support to the LAN devices they serve. They may also provide various management and
monitoring functions as well as a variety of configuration capabilities.
router port: A physical or logical connection between a router and a network. Where a network only allows the
use of one protocol, each physical connection corresponds to one logical router port. An example is the Netopia
ISDN Router’s LocalTalk port. Where a network allows the use of several protocols, each physical connection
may correspond to several logical router ports—one for each protocol used. Each router port has its own
network address.
routing table: A list of networks maintained by each router on an internet. Information in the routing table
helps the router determine the next router to forward packets to.
seeding: A method for ensuring that two or more routers agree about which physical networks correspond to
which network numbers and zone names. There are three options: non-seeding, soft seeding, and hard seeding.
Seeding can often be set separately for each router port. See also hard seeding, non-seeding, seed router, and
soft seeding.
seed router: A router that provides network number and zone information to any router that starts up on the
same network. See also hard seeding, non-seeding, seeding, and soft seeding.
serial port: A connector on the back of the workstation through which data flows to and from a serial device.
server: A device or system that has been specifically configured to provide a service, usually to a group of
clients.
SNMP (Simple Network Management Protocol): A protocol used for communication between management
consoles and network devices. The Netopia ISDN Router can be managed through SNMP.
soft seeding: A router setting. In soft seeding, if a router that has just been reset detects a network number or
zone name conflict between its configured information for a particular port and the information provided by
another router connected to that port, it updates its configuration using the information provided by the other
router. See also hard seeding, non-seeding, seeding, and seed router.
subnet: A network address created by using a subnet mask to specify that a number of bits in an internet
address will be used as a subnet number rather than a host address.
subnet mask: A 32-bit number to specify which part of an internet address is the network number, and which
part is the host address. When written in binary notation, each bit written as 1 corresponds to 1 bit of network
address information. One subnet mask applies to all IP devices on an individual IP network.
SDLC (Synchronous Data Link Control): A link-level communications protocol used in an International
Business Machines (IBM) Systems Network Architecture (SNA) network that manages synchronous,
code-transparent, serial information transfer over a link connection. SDLC is a subset of the more generic HDLC
(High-Level Data Link Control) protocol developed by the International Organization for Standardization (ISO).
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary 7
TCP/ IP (Transmission Control Protocol/ Internet Protocol): An open network standard that defines how
devices from different manufacturers communicate with each other over one or more interconnected networks.
TCP/ IP protocols are the foundation of the Internet, a worldwide network of networks connecting businesses,
governments, researchers, and educators.
telephone wall cable: 2-pair, 4-pair, or 8-pair, 22- or 24-gauge solid copper wire cable. Telephone wall cable is
sometimes called telephone station cable or twisted-pair cable.
TFTP (Trivial File Transfer Protocol/ Internet Protocol): A protocol used to transfer files between IP nodes.
TFTP is often used to transfer firmware and configuration information from a UNIX computer acting as a TFTP
server to an IP networking device, such as the Netopia ISDN Router.
thicknet: Industry jargon for 10Base-5 coaxial cable, the original Ethernet cabling.
thinnet: Industry jargon for 10Base-2 coaxial cable, which is thinner (smaller in diameter) than the original
Ethernet cabling.
UDP (User Datagram Protocol): A TCP/ IP protocol describing how packets reach applications in destination
nodes.
V.90: A modem data transmission standard, also known as V.PCM, which merges the K56flex standard with
the competing x2 standard. In September, 1998, the International Telecommunications Union is expected to
ratify the unified standard, thereby allowing interoperability of modems and ISPs’ central site equipment, with
appropriate firmware upgrades.
wall jack: A small hardware component used to tap into telephone wall cable. An RJ-11 wall jack usually has
four pins; an RJ-45 wall jack usually has eight pins.
WAN (wide area network): A network that consists of nodes connected by long-distance transmission media,
such as telephone lines. WANs can span a state, a country, or even the world.
WAN IP: In addition to being a router, the Netopia ISDN Router is also an IP address server. There are four
protocols it can use to distribute IP addresses over the WAN which include: DHCP, BOOTP, IPCP and MacIP. WAN
IP is a feature for both the Small Office and Corporate Netopia ISDN Router models.
wiring closet: A central location where a building’s telephone and network wiring is connected. Multi-story
buildings often have a main wiring closet in the basement and satellite wiring closets on each floor.
zone: An arbitrary subset of nodes within an AppleTalk internet. Creating multiple zones makes it easier for
users to locate network services. The network administrator defines zones when he or she configures routers.
Isolated networks have no zones. LocalTalk and EtherTalk Phase I networks may have no more than one zone
each. EtherTalk Phase II and TokenTalk networks may have more than one zone each. Several networks of any
AppleTalk type may share a zone name.
Download from Www.Somanuals.com. All Manuals Search And Download.
8 User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-1
Index
Numerics
10Base-T 5-4
B
A
Adding a filter set 14-13
features 8-9
answer profile
defined 9-4
CHAP
and answer profile 9-6
configuration files
answering calls 9-4
AppleTalk 1-2
routing table 13-9
zones 12-6, 12-7
downloading with TFTP 15-9
downloading with XMODEM 15-12
AppleTalk routing table 13-9
AppleTalk setup 12-1
AURP
Application software 5-2
AURP
uploading with XMODEM 15-12
SmartPhone 9-2
telephone connections 9-2
with console-based management 6-1, 7-1,
8-1
hop-count reduction 12-11
network number remapping 12-11
receiving connections 12-10
setup 12-3, 12-8
Configuring profiles for incoming calls. 9-6
configuring terminal emulation software 6-3
configuring the console 8-12
Connecting to an Ethernet network 5-3
Connecting to the configuration screens 8-8
AURP setup 12-8
AURP tunnel 14-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-2
connection profiles
defined 7-3
scheduling 9-1, 9-7
console
connection profile 7-3
IPX setup 7-4
navigating 6-4
overview 7-1
Enabling CNA 9-6
configuring 8-12
screens, connecting to 8-8
Console connection problems A-2
configuring with 6-1, 7-1, 8-1
5-2
device 13-7
WAN 13-6
D
D. Port 14-10
date and time
setting 8-11
deciding on an ISP account B-2
4
Deleting a packet filter 14-24
Deleting filters 14-17
designing a new filter set 14-11
DHCP
features 1-1
adding 14-13
defined 14-4
deleting 14-18
disadvantages 14-12
modifying 14-18
sample (Basic Firewall) 14-18
using 14-12
defined C-8
DHCP NetBIOS Options 10-18
Disadvantages of filters 14-12
display a filter set 14-9
distributing IP addresses C-5
Downloading a configuration file 15-9
downloading configuration files
with TFTP 15-9
viewing 14-17
filters
defined 14-4
deleting 14-17
input 14-15
modifying 14-17
output 14-15
parts of 14-7
with XMODEM 15-12
Dynamic Host Configuration Protocol (DHCP)
10-16
Dynamic Host Configuration Protocol, see
DHCP
priority 14-5
using 14-12
Dynamic WAN 10-16
viewing 14-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-3
finding an ISP B-1
firewall 14-18
firmware files
updating with TFTP 15-8
FTP sessions 14-21
further reading F-1
LED Status 13-3
LEDs 2-6, 13-3
LocalTalk 12-7
connecting 5-6
setup 12-7
G
defined C-8
MIBs supported 13-13
General Statistics 13-4
Glossary GL-1
H
hard seeding 12-3
Hops 13-10
I
Input filter 3 14-19
Input filters 1 and 2 14-19
IP addresses
NAT
attributes 10-5
defined 10-1
guidelines 10-5
using 10-3
navigating
about C-1
distribution rules C-10
static C-8
Easy Setup 6-4
Navigating through the configuration screens 8-
8
NCSA Telnet 6-3
NetBIOS 10-18, 11-3
Netopia
IP addresses, distributing C-5
IP Addressing C-1
IP setup 10-6
IPX packet filter sets 14-24
IPX packet filters 14-23
IPX SAP filters 14-26
IPX Setup 11-1
connecting to Ethernet, rules 5-3
connecting to LocalTalk 5-6
connection profile 7-3
distributing IP addresses 10-16, C-5
IP setup 7-4
IPX Spoofing 11-3
ISP
account types B-2
finding B-1
IPX setup 7-4
LocalTalk configuration 12-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-4
monitoring 13-1
see NAT 10-1
Network problems A-2
Next 13-10
Next Router Address 13-10
non-seeding 12-3
RIP 10-9
router to serve IP addresses to hosts 10-1
routing tables
AppleTalk 13-9
IP 10-12, 13-9
O
Output filter 1 14-19
overview 1-1
S
SAP server types 11-3
adding 9-9
P
packet
defined 9-1, 9-7
deleting 9-12
modifying 9-12
once-only 9-11
viewing 9-8
weekly 9-10
header C-13
PAP
and answer profile 9-6
Parts of a filter 14-7
password
user accounts 14-2
Ping 15-2
Plain Old Telephone Services
see POTS 9-1
security
filters 14-4Ð14-21
measures to increase 14-1
telnet 14-4
seeding 12-3
Show Static Routes 10-13
SNMP
Port numbers 14-8
port numbers 14-8
POTS 9-1
Protecting the configuration screens 14-2
Protecting the Security Options screen 14-2
proxy addresses 10-1
SmartIP 10-1
SmartPhone 9-1
configuring 9-2
SmartStart
Q
Quick View 13-1
before launching 3-1
requirements
Macintosh 3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
PC 3-1
Trivial File Transfer Protocol (TFTP) 15-7
troubleshooting
Macintosh A-2
PC A-1
Windows 95 3-3
SmartStart
SmartView 4-1
SNMP
Macintosh A-2
PC A-1
WAN statistics 13-4
MIBs supported 13-13
SNMP traps 13-15
Socket 11-2
soft seeding 12-3
Src. Port
14-10
State 13-10
static routes 10-12
statistics, WAN 13-4
subnet masks C-3
subnets C-2ÐC-5
multiple 10-10
with TFTP 15-8
with XMODEM 15-11
with TFTP 15-10
with XMODEM 15-12
nested C-11
using filters 14-12
T
TCP/ IP stack 5-2
Technical support A-3
telnet 6-2
V
access 8-8, 14-4
terminal emulation software
configuring 6-3
default settings 6-4
TFTP
W
WAN
defined 15-7
event history 13-6
statistics 13-4
downloading configuration files 15-9
updating firmware 15-8
uploading configuration files 15-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-6
WAN configuration 9-2, 10-3
WAN statistics 13-4, 13-5
Windows 95
SmartStart 3-3
X
XMODEM 15-10
XMODEM file transfers
downloading configuration files 15-12
updating firmware 15-11
uploading configuration files 15-12
Z
Zone Name 13-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty and Limitation of Remedies
1
Limited Warranty and Limitation of Remedies
Netopia warrants to you, the end user, that the Netopia™ Router with Dual Analog (the “Product”) will be free
from defects in materials and workmanship under normal use for a period of one (1) year from date of
purchase. Netopia’s entire liability and your sole remedy under this warranty during the warranty period is that
Netopia shall, at its option, either repair the Product or refund the original purchase price of the Product.
In order to make a claim under this warranty you must comply with the following procedure:
1. Contact Netopia Customer Service within the warranty period to obtain a Return Materials Authorization
(“RMA”) number.
2. Return the defective Product and proof of purchase, shipping prepaid, to Netopia with the RMA number
prominently displayed on the outside of the package.
If you are located outside of the United States or Canada, please contact your dealer in order to arrange for
warranty service.
THE ABOVE WARRANTIES ARE MADE BY NETOPIA ALONE, AND THEY ARE THE ONLY WARRANTIES MADE BY
ANYONE REGARDING THE ENCLOSED PRODUCT. NETOPIA AND ITS LICENSOR(S) MAKE NO OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THE ENCLOSED PRODUCT. EXCEPT AS
OTHERWISE EXPRESSLY PROVIDED ABOVE, NETOPIA AND ITS LICENSOR(S) DO NOT WARRANT, GUARANTEE OR
MAKE ANY REPRESENTATION REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT IN TERMS
OF ITS CORRECTNESS, ACCURACY, RELIABILITY, CURRENTNESS, OR OTHERWISE. THE ENTIRE RISK AS TO THE
RESULTS AND PERFORMANCE OF THE PRODUCT IS ASSUMED BY YOU. THE EXCLUSION OF IMPLIED
WARRANTIES IS NOT PERMITTED BY SOME STATES OR JURISDICTIONS, SO THE ABOVE EXCLUSION MAY NOT
APPLY TO YOU. IN THAT CASE, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO NINETY (90) DAYS
FROM THE DATE OF DELIVERY OF THE PRODUCT. THERE MAY BE OTHER RIGHTS THAT YOU MAY HAVE WHICH
VARY FROM JURISDICTION TO JURISDICTION.
REGARDLESS OF WHETHER OR NOT ANY REMEDY SET FORTH HEREIN FAILS OF ITS ESSENTIAL PURPOSE, IN
NO EVENT WILL NETOPIA, ITS LICENSOR(S) AND THE DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS OF ANY
OF THEM BE LIABLE TO YOU FOR ANY CONSEQUENTIAL, INCIDENTAL OR INDIRECT DAMAGES (INCLUDING
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION,
AND THE LIKE) ARISING OUT THE USE OR INABILITY TO USE THE PRODUCT EVEN IF NETOPIA OR ITS
LICENSOR(S) HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES OR
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. NETOPIA AND ITS LICENSOR(S)
LIABILITY TO YOU FOR ACTUAL DAMAGES FROM ANY CAUSE WHATSOEVER, AND REGARDLESS OF THE FORM
OF THE ACTION (WHETHER IN CONTRACT, TORT [INCLUDING NEGLIGENCE], PRODUCT LIABILITY OR
OTHERWISE), WILL BE LIMITED TO $50. v.697
Download from Www.Somanuals.com. All Manuals Search And Download.
2
User’s Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Miele Dishwasher G 5915 SCI User Manual
Miller Electric Welding System Big Blue 400 KX User Manual
Milwaukee Saw 6232 20 User Manual
MTD Blower 160r User Manual
NEC Home Theater System M332XS User Manual
Network Technologies Switch ST nXm U User Manual
Nokia Cell Phone 1006 User Manual
Numark Industries DJ Equipment DXM09 User Manual
NXP Semiconductors Switch PIP3119 P User Manual
Palsonic CRT Television 7610WSPF User Manual