Naut Air fm_2008.qxd:Naut Air fm.qxd 6/25/08 4:23 PM Page i
Dear Nautique Owner,
Welcome to the Nautique Family! For over 80 years, Nautiques by
Correct Craft has been dedicated to providing our customers and
their families with the finest inboard boats available. It’s our passion
to create the best performing boats in the industry. Boats that allow
you to escape the routine of every day life. Our customers don’t just
own a Nautique, they live the Nautique life.
Your boat has been built with the best material and workmanship
available, a legacy handed down from our founder. Our wealth of
experience gives us the edge in innovation, quality and
performance. We have the most dedicated and loyal employees in
the industry. Hands down. Every day, our employees do more than
just punch a clock; they take personal pride in every boat that comes
down the line.
Review this Owner’s Manual for your boat. We have assembled this
manual to inform you about your Nautique and educate you further
on boating. Please pay particular attention to the safety statements
labeled as DANGER, WARNING, CAUTION and NOTICE. These
statements alert you to possible safety hazards to avoid so you can
have a safer boating experience. There are also many tips and tricks
on care and maintenance sprinkled throughout the manual. Boating
is very important to us and we would like you to enjoy many years of
boating in your Nautique.
By purchasing a Nautique, you have taken the first step in trading
your old lifestyle for a new one. Now that you own a Nautique, life as
you know it will never be the same.
Enjoy the Nautique Life.
The Nautique Team
Keep your heart with all diligence,
for out of it spring the issues of life.
Proverbs 4:23
P/N 80128
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air fm_2008.qxd:Naut Air fm.qxd 6/25/08 4:23 PM Page iii
Boater’s Checklist
For improved safety and enjoyment, check each of these items:
Check Before You Launch Your Boat:
• Read both the engine and the boat operator manuals.
• Drain plug (Securely in place?)
• Propeller Condition (Prop nut tight and secured, no cracked
or bent blades, prop turns freely?)
• Steering System (Working smoothly and properly, self
locking nuts in place?)
• Battery (Fully charged, cable terminals clean and tight?)
• Capacity Plate (Are you overloaded?)
• Weather conditions (Safe to go out?)
• Fuel and Oil (Sufficient for trip, check bilge area for gas
odor, no leaks?)
• Hoses and Connectors (No leaks or damage?)
• Electrical Equipment (Lights, horn, pumps, etc.?)
• Safety Equipment (Fire extinguisher, bailer, paddle, anchor
and line, mooring lines, signaling device, tool kit, first aid
kit, first aid manual?)
• Personal Flotation Devices for all occupants
• Float Plan submitted to Responsible Person (Verbal or
written?)
Check Before You Start Your Engine:
• Fuel (Sufficient for trip, check bilge area for gas odor?)
• Control Lever in Neutral
• Capacity Plate (Are you overloaded?)
• Personal Flotation Devices for all occupants
• Seating (Everyone in proper place?)
• Engine Stop Switch and Lanyard (Operational and securely
fastened?)
• No one in water near boat
• Keep firm and continuous grip on steering wheel
• Engine Cooling Water Valve open
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air fm_2008.qxd:Naut Air fm.qxd 6/25/08 4:23 PM Page iv
Restricted Areas
Before boating, check with Local, State and Federal authorities to
identify restricted areas. Because of the threat of terrorism, the U.S.
Coast Guard has and will continue to implement strict limits on
watercraft near U.S. Navy and Coast Guard ships and other
potential targets.
Proposition 65
A wide variety of components used on this vessel contain or emit chemicals knows to the State
of California to cause cancer and birth defects and other reproductive harm.
EXAMPLES INCLUDE:
Engine and generator exhaust.
Engine and generator fuel, and other liquids such as coolants and oil, especially used motor oil.
Cooking fuels.
Cleaners, paints and substances used for vessel repair.
Waste materials that result from wear of vessel components.
Lead from battery terminals and from other sources such as ballast or fishing sinkers.
TO AVOID HARM:
Keep away from engine, generator and cooking fuel exhaust fumes.
Wash area thoroughly with soap and water after handling the substances above.
California Health & Safety Code 25249.5-.13
KC-0206-B
Emission Control Warranty
Information
The engine in your Nautique boat meets the
strict requirements set forth by the California
Air Resources Board (CARB). The engine has a
special environmental tag and the boat has this
label affixed to it. The tag and the label are
CORC013
required by the California Air Resources Board
(CARB). The label has 1, 2, 3 or 4 stars. The label MUST be affixed
to the boat, if the boat is operated in the state of California and/or
bordering waters.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air fm_2008.qxd:Naut Air fm.qxd 6/25/08 4:23 PM Page v
Boating Terminology
LENGTH OVERALL (LOA)
PORT
SIDE
STARBOARD
SIDE
HELM
TRANSOM
STERN
FORWARD
BOW
AFT
GUNWALE
FREEBOARD
DRAFT
WATERLINE
CORC001
* An easy way to remember PORT side from STARBOARD side is
“PORT” and “LEFT” both have four letters.
Product Improvement
Because of our policy of continuous product improvement, the
illustrations used in this manual may not look the same as on your
boat and are intended only as representative reference views. Some
illustrations may also show optional accessories which may or may
not be available for your boat. Many optional accessories can only
be installed at the time the boat is manufactured and cannot be
installed by your dealer. Your dealer will be happy to provide details
on installing accessories.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air fm_2008.qxd:Naut Air fm.qxd 6/25/08 4:23 PM Page vi
Table of Contents
Welcome.....................................i Recommended Safety
Record Important
Equipment ...........................1-20
Information...............................ii Emergency Stop Switch and
Boater’s Checklist....................iii Lanyard.................................1-21
Restricted Areas .......................iv Emergencies.........................1-22
Proposition 65..........................iv
Emission Control Warranty
Information ..............................iv
Boating Terminologyv
Fire/Explosion .................1-22
Capsizing and
Swamping..........................1-23
Collisions...........................1-23
Grounding ........................1-23
Water Rescue
Product Improvement..............v
Boating Safety ......................1-1
Safety While Boating .............1-1
General Precautions..............1-3
Boat Safety Labels..................1-5
Boating Regulations ..............1-8
Boater Responsibilities..........1-8
Registration/
Documentation......................1-9
Insurance..............................1-10
Education Opportunities....1-10
Operating By Minors...........1-11
Overloading .........................1-11
Passenger Safety and
Seating ..................................1-13
Visibility ................................1-13
Boating Under the
Influence ..............................1-14
Reporting Accidents............1-15
Rendering Assistance ..........1-15
Required Safety
(Man Overboard).............1-23
Medical Emergency..........1-24
Operation Failure.............1-24
Hazardous Conditions ........1-24
Shallow Water
Operation..........................1-24
Weeds.................................1-24
Dam Spillways ...................1-25
Weather/Seas....................1-25
Warning Markers..............1-26
Carbon Monoxide ...............1-27
Our Environment................1-28
Foreign Species ................1-28
Fuel/Oil Spillage..............1-28
Discharge/Disposal of
Waste..................................1-29
Excessive Noise.................1-29
Wake/Wash.......................1-29
Exhaust Emissions............1-29
Paints .................................1-29
Cleaning Agents ...............1-30
MARPOL Treaty ...............1-30
Watersport Safety.................1-30
Teak/Drag Surfing...........1-30
General Watersport
Equipment ...........................1-15
Life Saving Equipment ....1-16
Navigation Lights .............1-18
Horn or Whistle ...............1-18
Fire Extinguisher..............1-18
Visual Distress Signals ......1-18
Precautions .......................1-32
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air fm_2008.qxd:Naut Air fm.qxd 6/25/08 4:23 PM Page vii
Watersports Responsibility
Controls and Indicators........4-1
Code ..................................1-35 Steering...................................4-1
Hydro-Gate™ Control and
Basic Rules of the Road.......2-1
SportShift................................4-2
Aids to Navigation .................2-1
Shifter/Throttle.....................4-4
USWMS System ..................2-2
Emergency Stop Switch .....4-5
Uniform State Regulatory
Standard Dash Pod -
Markers................................2-3
210, 211 ..................................4-6
FWMS System......................2-3
Gauges.................................4-6
Right of Way...........................2-5
Speedometer Calibration ..4-8
Privileged Boats ..................2-5
Control Switches.................4-8
Burdened Boats..................2-5
12-Volt Port .......................4-10
Crossing Situation ..............2-6
Ignition Keyswitch............4-11
Meeting Head-On ..............2-7
Smart Pod - Limited or
Overtaking ..........................2-8
Team .....................................4-11
The General Prudential
Gauges...............................4-11
Rule......................................2-9
Control Switches...............4-12
Night Running....................2-9
12-Volt Port .......................4-16
Da Pod - Limited or
210, 211, 220, 230
Team .....................................4-16
Ignition and Switch
Panel..................................4-16
Nautique Cruise
Control ..............................4-21
Gauges...............................4-24
Tachometer/Fuel
and 236 ................................3-1
Specifications .........................3-1
210 .......................................3-1
211 .......................................3-1
220 .......................................3-2
230, 236 ...............................3-2
211, 220 Dash Pod and
Monitor .............................4-31
Standard Equipment...........4-37
Watersports Tow Point.....4-37
Bow Features of Your
Nautique............................4-38
Driver’s Seat
Adjustment........................4-39
Rearview Mirror
Adjustment .......................4-40
Love Seat...........................4-41
Storage Hatch...................4-41
Engine Cover Hatch ........4-42
Console...................................3-3
210, 230 and 236 Dash Pod
and Console ...........................3-4
Ignition and Switch Panel.....3-5
Keys .........................................3-6
210 Deck Layout....................3-8
211 Deck Layout..................3-10
220 Deck Layout..................3-12
230, 236 Deck Layout..........3-14
Standard and Optional
Equipment ...........................3-16
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air fm_2008.qxd:Naut Air fm.qxd 6/25/08 4:23 PM Page viii
Walk-Thru Windshield
Shifting .................................6-14
Opening/Latching...........4-43 Steering.................................6-14
Coolers ..............................4-43 Stopping ...............................6-15
Boarding Platform............4-44 Docking ................................6-15
Engine Cooling Water
Running................................7-1
Intake Valve.......................4-45
Maneuvering Techniques .....7-2
Fuel Tank ..........................4-46
Tow Pattern ............................7-3
Battery Selector Switch ....4-47
Freezing Temperatures .........7-4
Automatic Bilge Panel .....4-48
Anchoring ..............................7-4
Folding Instructions for
Dropping Anchor...............7-5
®
Flight Control Tower –
Weighing (Pulling In)
Optional............................4-49
Anchor.................................7-6
210, 220, 230 and
Performance Boating............7-7
236 - Optional Tower .......4-50
Propellers ...............................7-7
Stainless Steel Tower........4-51
Flight Clips™....................4-52
Ballast Tanks .....................4-53
Ballast Tank Control
Care and Maintenance .........8-1
General Maintenance............8-1
Engine Intake Water
Switches.............................4-53
Optional Accessories...........4-55
Stereo and Speaker
Strainer................................8-2
Bilge Pumps ...........................8-3
Propeller.................................8-4
Removal...............................8-4
Installation ..........................8-5
Propeller Shaft Stuffing
Box..........................................8-6
Through-Hull Fittings...........8-6
Quick Oil Drain System ........8-6
Salt Water Boating.................8-7
Pods ...................................4-55
Boat Systems ........................5-1
Fuel System.............................5-1
Ballast Tanks and Bilge
System.....................................5-3
Heater System-Optional........5-5
Getting Underway................6-1 Fresh Water Flushing Kit-
Safety Checklist......................6-1 Optional .................................8-7
Safety Equipment ..................6-2 Battery Maintenance .............8-8
Fueling....................................6-2 Gelcoat Maintenance ..........8-10
Gasoline Containing
Care of Metal .......................8-11
Alcohol ................................6-3 Care of Glass ........................8-11
Boarding.................................6-5 Vinyl Maintenance and
Boat Planing...........................6-5 Cleaning ...............................8-11
Pre-Operation Checks...........6-6 Tunable Rudder...................8-13
Flooded Engine................6-11
Break In Procedure..........6-13
Propeller Selection...........6-13
Rudder Remote Lube
Fitting ................................8-14
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air fm_2008.qxd:Naut Air fm.qxd 6/25/08 4:23 PM Page ix
Transmission ........................8-15
Shift Cable.........................8-16
Glossary ..............................G-1
Warranty..............................W-1
CORRECT CRAFT LIMITED
WARRANTY..........................W-1
Lifetime Limited
Warranty.............................W-1
Transferable Lifetime
Limited Warranty..............W-1
Boat Five (5) Year
Transferable Limited
Warranty.............................W-2
Gel Coat Three (3) Year
Non-transferable Limited
Warranty.............................W-2
Engine Warranty ...............W-2
Request for Transfer of
Warranty on Parts.................W-5
Request for Warranty
Transfer of Hull, Deck,
Troubleshooting...................9-1
Trouble Check Chart ............9-2
Performance.......................9-2
Electrical..............................9-3
Storage ...............................10-1
Lifting Rings and Lifting
Eyes .......................................10-1
Winterizing Your Boat.........10-3
Check for Water in Your Fuel
System...................................10-5
Winterizing Ballast Tanks
(if equipped)........................10-6
Trailer/Trailering ................10-7
Hitch..................................10-7
Wiring................................10-7
Security..............................10-7
Towing Your Boat.............10-8
Long Trips.........................10-8
and Stringer..........................W-6
Nautique Regional
Centers ..................................W-7
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air fm_2008.qxd:Naut Air fm.qxd 6/25/08 4:23 PM Page x
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-1
S e c t io n 1
B o a t in g S a f e t y
S a f e t y W h ile B o a t in g
Boating-related accidents are generally caused by the operator’s
failure to follow basic safety rules or written precautions. Most
accidents can be avoided if the operator is completely familiar with
the boat, its operation and can recognize potentially hazardous
situations.
In addition to everyday safety, failure to observe the safety
recommendations may result in severe personal injury or death to
you or to others. Use caution and common sense when operating
your boat. Do not take unnecessary chances! Remember that at
least three people are needed for safely towing watersport
participants.
Failure to adhere to these warnings may result in severe injury or
death to you and/ or others.
• Look before you turn the boat. As a boater you are obligated
to maintain a course and speed unless it is safe to alter
course and speed. Look before you turn.
• Improper operation of the boat is extremely dangerous.
Operators must read and understand all operating manuals
supplied with the boat before operation.
• On-board equipment must always conform to the governing
federal, state and local regulations.
• Prior to starting the engine, you MUST open the engine box
and check the engine compartment and bilge for gasoline
and oil vapors. You MUST also operate the blower for at
least four minutes. Failure to do so may result in fire or
explosion. If you smell gasoline vapor or see liquid gasoline,
DO NOT start the engine.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-2
S e c t io n 1
• DO NOT operate the boat while under the influence of
alcohol or other drugs.
• DO NOT stand or allow passengers to stand in the boat, or
sit on the transom, seat backs, engine cover or sides of the
boat while the engine is running. You or others may be
thrown from the boat.
• DO NOT allow any type of spark or open flame on board. It
may result in fire or explosion.
• DO NOT leave children in the boat without adult
supervision.
• DO NOT sit in front of the operator to avoid obstructing the
operator’s view.
• DO NOT dive from the boat without being absolutely sure
of the depth of the water, otherwise severe injury or death
may occur from striking the bottom or submerged objects.
• DO NOT swim near the boat when the engine is running.
Being in NEUTRAL is not enough, the propeller may still be
turning and carbon monoxide may be present.
• DO NOT replace your boat’s marine parts with automotive
parts.
• DO NOT remove or modify any components of the fuel
system except for maintenance by qualified personnel.
Tampering with fuel components may cause a hazardous
condition.
• DO NOT wrap ski lines or mooring lines around any body
part which may become entangled in the line if you fall
overboard and the boat is moving.
• Keep track of ski lines and dock lines so they do not become
entangled in the propeller.
• Be sure to securely attach the engine Emergency Stop switch
lanyard to a part of your clothing, such as a belt loop, when
operating the boat.
• Be sure to keep a watch for other boats, swimmers and
obstructions in the water. Stay away from other boats and
personal watercraft.
• Be sure to have an experienced operator at the helm and
always have at least three people present for safe towing –
one to drive, one to observe and one to ski or ride.
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-3
B o a t in g S a f e t y
• Seek shelter from open water if there is threat of lightning.
• Operate slowly in congested areas such as marinas and
mooring areas.
• The bow may be slippery. Do not go forward while the
engine is running.
• When you leave the boat take the keys with you. This will
keep untrained and unauthorized persons from operating
the boat.
• Engine exhaust contains carbon monoxide.
• DO NOT operate the engine in a confined space.
• DO NOT go under the boat cover with the engine
running or shortly after the engine has been running.
• DO NOT use boarding platform with the engine
running.
• DO NOT “teak surf.”
• Allow adequate ventilation with fresh air before
entering.
• Slow down when crossing waves or wake in order to
minimize the impact on passengers and the boat.
G e n e r a l P r e c a u t io n s
Your safety, the safety of your passengers and other boaters are
among your responsibilities as operator of this boat. Your boat must
be in compliance with USCG safety equipment regulations. You
should know how to react correctly to adverse weather conditions,
have good navigation skills, and follow the "Rules of the Road" as
defined by the USCG and state/ county/ local regulations.
Before each outing you should check all safety equipment, such as
fire extinguishers, PFDs, flares, distress flags, flashlights and
emergency stop switch. They should be operable, in good
condition, readily visible and easily accessed.
Know the weight capacity of your boat. DO NOT overload your
boat.
This section covers general boating safety information. Throughout
this manual specific precautions and symbols identify safety related
information.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-4
S e c t io n 1
The Safety Alert Symbol means ATTENTION! BECOME
ALERT! YOUR SAFETY IS INVOLVED!
!
!
!
Indicates a hazardous situation, which, if
not avoided, will result in death or serious injury.
!
Indicates a hazardous situation, which, if
not avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation, which, if not
avoided, may result in minor or moderate injury.
NOTICE
Indicates a property damage message.
The precautions listed in this manual and on your Nautique boat
are not all-inclusive. If a procedure, method, tool, or part is not
specifically recommended, you must satisfy yourself that it is safe for
you and others, and that the boat will not be damaged or made
unsafe as a result of your decision. REMEMBER - USE COMMON
SENSE WHEN OPERATING YOUR BOAT!
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-5
B o a t in g S a f e t y
B o a t S a f e t y L a b e ls
Your Nautique boat is affixed with various safety labels at the time
of manufacture. These labels appear at specific locations on the
boat where safety is of particular concern. Safety labels must be
legible. If you suspect a label is missing or one becomes damaged,
contact your Nautique dealer for immediate replacement.
CORC007
CORC004
Tow Pylon
Engine Inside Box and
on Fuel Tank
CORC091
CORC216
Water Strainer
Fuel Fill
CORC008
CORC006
Throttle Control
Transom Warning
WARNING!
BEFORE OPERATING
ENGINE, INSPECT
FOR LEAKAGE
If leakage is present, do not operate engine!
CORC092
CORC010
Cross Member/ Boarding Platform
Engine
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-6
S e c t io n 1
Avoid personal injury
or property damage
caused by flying objects.
Remove any items from
board racks when
trailering boat.
ENGINE WITH FLAME ARRESTOR REMOVED
ATTEMPT TO START OR OPERATE
CORC094
CORC093
Flame Arrestor
Board Racks
CORC064
Walk Through Windshield
CORC009
211 and 220
WARNING
DANGER
Gasoline vapors can
explode resulting in
injury or death. Before
engine start-up, check
engine compartment
for gasoline vapors,
then run blower for four
minutes. Run blower
when below cruising
speed.
A
spinning propeller
or carbon monoxide
fumes can cause
serious injury or
death. Do not start or
run engine while
anyone is on or near
the boarding platform.
Do not operate this
FIRE EXTINGUISHER SYSTEM
Armed when light is on.
See Owners Manual
boat
Correct Craft, Inc.
boarding platform
secured in place.
without
a
CORC204
CORC203A
210, 230 and 236
Dash Pod
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-7
B o a t in g S a f e t y
CORC011
CORC095
Fuel Control Cell
Flight Control Tower®
Never run engine when the operator is not seated facing
forward with hands on the controls.
Leaking fuel is
a
fire and explosion hazard; inspect fuel
system regularly and fix leaks immediately.
Do not sit on seat backs, boat sides, or engine box while
engine is running. Do not stand on boat sides at any time.
Do not make high speed maneuvers in this boat.
Always test the emergency engine shut off switch for proper
function before operating the boat and never operate the boat
unless the lanyard is securely attached to the driver.
Always empty all ballast systems before lifting or trailering boat.
To insure safe use and maintenance of this boat, read and
understand the owners manual thoroughly. If you do not have
manual, contact: Correct Craft, Inc. - 14700 Aerospace PKY.
Orlando, FL 32809 (407) 855-4141. ski@skinautique.com
a
Correct Craft, Inc. installs
a
permanent wake
enhancement ballast tank system in some models. The full
weight of this system has already been considered in the boat weight and
therefore does not influence maximum capacity, unlike portable ballast tanks or
weights, which must be included as part of the gear weight.
14700 Aerospace Pky. Orlando, FL 32809
CORC200
CORC003
211 and 220
210, 230 and 236
Side Console
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-8
S e c t io n 1
B o a t in g R e g u la t io n s
The U.S. Coast Guard (USCG) is the authority of the waterways;
they are there to help the boating public. State boating regulations
are enforced by local authorities. You are subject to marine traffic
laws and “Rules of the Road” for both federal and state waterways;
you must stop if signaled to do so by enforcement officers, and
permit to be boarded if asked.
There are many pamphlets, prepared by the USCG, available to
you. These pamphlets explain “Rules of the Road,” signal lights,
buoys, safety, international and inland regulations and much more
than is presented in the manual. For more information, contact
your local USCG Unit or call the Coast Guard Customer Infoline at
1-800-368-5647.
B o a t e r R e s p o n s ib ilit ie s
It is the owner’s responsibility to ensure that the operator of the
boat has been properly instructed in the lawful and safe operation
of this vessel. Therefore, before operating the boat, read this
owner/ operator manual. Be sure you understand each item before
operating it. Improper operation or trailering of the boat could
lead to severe damage and/ or injury.
At the time of delivery, the owner/ operator is responsible for:
• Understanding warranty terms and conditions of your boat,
your engine and your trailer.
• Obtaining insurance.
• Examining boat to ensure proper operation of all systems.
Before operating the boat, the owner/ operator is responsible for:
• Obtaining state registration of the boat.
• Providing the proper USCG required safety equipment.
• Following proper break-in procedure for the engine.
• Understanding safety information and proper operating
procedures within this manual.
While operating the boat, the owner/ operator is responsible for:
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-9
B o a t in g S a f e t y
• Knowing that all safety equipment and personal flotation
devices (PFDs) are in good condition and suitable for your
boat and passenger load.
• Knowing that the capacity of the load are within the limits
stated on the USCG Maximum Capacities Plate.
• Verifying that the emergency stop switch is in proper
operating condition.
• Ensuring that all passengers are properly and securely seated
in appropriate seating locations.
• Following safe operating practices and the “Rules of the
Road.”
• Understanding proper maintenance and knowledge of the
boat’s operating systems.
• Providing safety training for the passengers.
• Having at least one other passenger who is capable of
handling the boat in an emergency.
• Maintaining a proper lookout by sight and hearing.
• Avoiding use of alcohol and other drugs.
• Providing assistance to other boaters.
R e g is t r a t io n / D o c u m e n t a t io n
The USCG requires that all power boats operated on the navigable
waters of the U.S. must be registered in the state of main use; also,
many states require registration in that state whenever boating on
waters within their state boundary. Contact your state boating
authorities (and neighboring states) for registration information
on boats and trailers. Your Nautique dealer can supply you with the
appropriate forms.
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-10
S e c t io n 1
In s u r a n c e
You must get insurance before operating your new boat. Insurance
for loss by fire, theft or other causes, or liability protection against
accidents is a must for responsible boaters. The boat owner is
legally responsible for any damage or injury caused when he, or
someone else operating the boat, is involved in an accident. Many
states have laws detailing minimum insurance needs. Your
insurance agent or your Nautique dealer may be able to supply you
with more information.
E d u c a t io n O p p o r t u n it ie s
This manual is not intended to provide complete training on all
aspects of boat operation. We strongly recommend that all
operators of this boat seek additional training on boat handling
and safety. Have all operators become familiar with the handling
characteristics, and proper steering and control system usage
before attempting high speed operation.
Some states require youths 16 years of age and younger to complete
a boating safety course before operating any watercraft. Many
others require operators under the age of 18 to be licensed in small
boat operation.
Boat smart from the start, take a boating safety course and get a free
vessel safety check annually for your boat. For more information,
contact: United States Coast Guard Auxiliary, 1-800-368-5647,
www.cgaux.org; United States Power Squadrons, 1-888-FOR-USPS,
www.usps.org.
Most boaters can enhance their enjoyment of boating experiences
through increased knowledge of safe operation, navigation and
regulation of pleasure boats. The following is a list of some other
agencies and organizations that offer Water Safety, First Aid and
CPR courses or information. To find boating safety courses in your
area, call your state’s local boating agency or the USCG boating
safety courseline at 1-800-336-2628 (1-800-245-2628 in Virginia).
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-11
B o a t in g S a f e t y
• American Red Cross
• U.S. Coast Guard Auxiliary
• U.S. Power Squadrons
• State Boating Offices
• Canadian Power and Sail Squadrons
• Boat Owners Association of the United States
• National Safe Boating Council
O p e r a t in g B y M in o r s
Minors must be supervised by an adult whenever operating a boat.
Many states have laws regarding the minimum age and licensing
requirements of minors. Be sure to contact the state boating
authorities for information.
O v e r lo a d in g
!
An overloaded boat can cause death or
serious injury. Do not purposely overload or add any
additional water to the boat other than to the Nautique
Launch Control System.
DO NOT overload your boat. Your boat is equipped with a required
capacity plate indicating the maximum acceptable load as
determined by the manufacturer following certain Federal
guidelines. If in doubt, contact your Nautique dealer.
2200
14
2200
CORRECT CRAFT, INC.
14700 AEROSPACE PKY
Nautique 236 ORLANDO, FL 32839
CORC021
CORC201
211 and 220
210, 230 and 236
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-12
S e c t io n 1
The capacity plate is used by boat manufacturers participating in
the National Marine Manufacturers Association certification
program. Nautiques by Correct Craft has submitted your model for
inspection and compliance with their guidelines.
The capacity plate has the following information permanently
printed on it. It is attached to the boat by the throttle for the
operator to read before they drive the boat.
• The total weight of persons, gear and other items which the
boat is capable of carrying under normal conditions. This
weight must include any added ballast other than the
Nautique Launch Control System™.
• Death or serious injury can occur from overloading the boat.
DO NOT purposely overload your Nautique boat. Do not fill
the bilge area with water to act as ballast.
• The maximum number of persons allowed on the boat. This
information on the capacity plate applies under normal
conditions and special care must be used in any other than
normal conditions. Check the capacity plate on your boat
and abide by these limits.
NOTICE
Correct Craft, Inc. installs permanent wake enhancement ballast
tanks called the Nautique Launch Control System™ in some models.
The full weight of this system has already been considered in the boat
weight and therefore does not influence maximum capacity, unlike
portable ballast tanks or weights, which must be included as part of
the gear weight.
An overloaded Nautique will handle differently than a lightly
loaded one. Drive and turn your Nautique with this in mind. As
wakeboarding has developed, we have witnessed the advent of
ballast systems which add weight and increase the size of the wake.
The simplest ballast system on the market is the water ballast type,
such as the “phat sack.” It is not uncommon to see operators use
such systems and then put additional people in their boat. Please be
advised that this practice can lead to overloading your boat. Each
Nautique boat has a required capacity label displaying the
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-13
B o a t in g S a f e t y
maximum weight of people, gear and ballast that can be placed in
the boat. Always be aware of the load in your boat and do not load
the boat in excess of the listed capacity. The quest for the "phattest"
wake has caused some to excessively overload their boats.
Overloading the boat will affect the operation and, possibly result
in injury to persons inside and/ or outside of the boat.
P a s s e n g e r S a f e t y a n d
S e a t in g
Make sure that at least one passenger is familiar with the operation
and safety aspects of the boat in case of an emergency. Show all
passengers the location of emergency equipment and explain how
to use it.
The operator of the boat is responsible for the safety of the
passengers as well as his/ her own safety. The operator should
ensure that all passengers are properly and securely seated in
appropriate seating locations before starting.
While the engine is running, and during the boat mooring, all
occupants should be properly seated. DO NOT sit on the engine
box, seat backs, boarding platform or gunnels. You could fall
overboard and be hit by the propeller. DO NOT allow objects, arms
or legs, or any other body parts to hang over the bow or gunnels.
DO NOT stand while the boat is moving.
The operator MUST sit in the driver’s seat while the boat is moving
and all passengers remain properly seated.
V is ib ilit y
!
Obstructed visibility can cause death or
serious injury. Maintain clear visibility at all times.
Arrange passengers and equipment for maximum
visibility or designate a passenger to assist when
visibility is limited.
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-14
S e c t io n 1
The operator of the boat is responsible by law to “maintain a proper
lookout by sight and hearing.” The operator must ensure that
he/ she has an unobstructed view particularly to the front. No
passengers or equipment should block the operator’s view.
Look carefully before turning, especially when you are turning
around to pick up a fallen skier. Someone else may not be following
the “Rules of the Road.”
Keep a visual check for boats behind your boat. This is an area
where accidents can happen very quickly.
The boat should not be driven at a rate of speed faster than will
allow it to be brought to a full stop within the operator’s field of
view.
B o a t in g U n d e r t h e In f lu e n c e
!
Impaired operation can cause death or
serious injury. Federal and state law prohibit operating a
boat under the influence of alcohol and other drugs.
These regulations are actively enforced.
Boating, alcohol and the use of other drugs just do not mix. Mixing
boating, alcohol and other drugs result in many marine accidents
and deaths. These substances increase your reaction time and
impair your judgment. Combined with the sun, wind, waves and
noise of other watercraft, the effects of drugs are increased and will
significantly increase your reaction time. As the owner/ operator,
you are responsible for the alcohol/ drug use and onboard
behavior of your passengers.
NOTICE
If the operator’s blood alcohol content is above the legal limit, violators
are subject to a civil penalty up to $1,000.00 or criminal penalty up
to $5,000.00, one year imprisonment or both. Operating a boat
under the influence can also result in a loss of automobile driving
privileges.
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-15
B o a t in g S a f e t y
R e p o r t in g A c c id e n t s
The USCG requires the owner or operator of a boat involved in an
accident, to report the incident to the proper marine law
enforcement agency for the state in which the accident occurred.
Immediate notification to the nearest State boating authority is
required if a person dies or disappears as a result of a recreational
boating accident. If a person dies or sustains injuries requiring
more than first aid, a formal report must be filed within 48 hours of
the accident. A formal report must be filed within 10 days for
accidents exceeding $500 in property damage or complete loss of
boat.
R e n d e r in g A s s is t a n c e
If you see a distress signal or suspect a boat is in trouble, you must
assume it is a real emergency and render assistance immediately. By
law, the operator in charge of the craft is obligated to provide
assistance to any individual in danger if such assistance can be
provided safely. Failure to render assistance can result in a fine
and/ or imprisonment.
The 1971 Boating Safety Act grants protection to a "Good
Samaritan" boater providing good faith assistance, and absolves a
boater from any civil liability arising from such assistance.
R e q u ir e d S a f e t y E q u ip m e n t
The Federal Boat Safety Act of 1971 (FBSA/ 71) established
minimum safety standards for boats and associated equipment,
specified by the USCG. In addition, the ABYC and the NMMA work
with boat builders to develop voluntary standards that exceed base
requirements.
The included safety equipment on your Nautique boat meets or
exceeds the standards of the USCG, ABYC and the NMMA. Some
required safety equipment such as PFDs are not included with your
Nautique boat. Your Nautique dealer can help you choose the
appropriate equipment.
NOTICE
Many states’ equipment requirements go beyond USCG requirements.
Contact your state boating office for further information.
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-16
S e c t io n 1
Equipment requirements for coastal and
inland waters differ. Check with local
authorities or the USCG for further
information
about
coastal
water
requirements.
The following equipment may or may not be
required by federal/ local regulations.
Type I
Life Preservers
Life Saving Equipment
Federal law requires at least one Type I, II, III,
or V Personal Flotation Device (PFD), of the
proper size, for each person on board or
being towed, and at least one Type IV
throwable PFD in the boat.
There are four types of PFDs to wear and one
type used for throwing in emergency
situations.
Type II
Buoyant Vests
Type I Life P res erver: Most buoyant PFDs
are effective on all waters, especially open,
rough water.
Type II Buoya nt Ves t : Good for calm water
near shore on most inland waters where quick
rescue is likely.
Type III Flot a t ion Aid: Good for most
inland water applications where quick rescue
is likely. Comes in various styles and some are
designed for water sport activities.
Type III
Flotation Aids
Type V Hybrid P FD: Inflatable design for
special use activities and may be used instead
of a Type I, II, or III PFD if used in accordance
with the approval conditions on the label and
if worn when the boat is underway. Some Type
V PFDs provide increased protection against
hypothermia.
Type V - Hybrid PFD
Must Be Worn
When Underway
1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-17
B o a t in g S a f e t y
NOTICE
•
•
A Type V PFD must be worn to be counted toward the
minimum carriage requirements.
Special PFDs are available for skiing and other water sports.
These PFDs are constructed with materials suitable for high
impact falls.
PFDs are intended to help save lives. The operator should set an
example by wearing one. Wear a PFD whenever boating. It is
especially important that children and non-swimmers wear a PFD at
all times. Make certain all passengers know how to put on and
properly adjust their PFDs. Also, selecting the proper type PFD for
your kind of outing helps ensure your time on the water can be the
safest possible.
At the beginning of each season, check PFDs for damage and test
for proper flotation. Refer to the PFD manufacturer’s information.
All boats over 16 feet (4.8 meters) in length must carry one USCG
approved Type IV throwable lifesaving device, such as a ring buoy
or buoyant cushion. To meet requirements, each lifesaving device
must have a current, legible USCG approval stamp permanently
affixed.
Type IV Throw a ble Device: Intended for heavy traffic inland
waters where help is available. Designed to be thrown to a person
in the water and should never be worn.
Type IV
Throwable Devices
Your Nautique dealer can help you select appropriate PFDs and
throwable lifesaving devices for your area.
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-18
S e c t io n 1
Navigation Lights
All power boats underway between sunset and sunrise must display
proper navigation lights. All boats at anchor must display a proper
anchor light. The anchor light must be visible 360 degrees.
Horn or Whistle
All boats over 16 feet (4.8 meters) in length must be equipped with
an operable horn or whistle, audible from one mile. Your Nautique
boat is equipped with a USCG approved horn.
Fire Extinguisher
At least one approved B-1 portable fire extinguisher is required.
Make sure all passengers know the location and operating
procedure for each fire extinguisher. Check fire extinguisher
regularly for condition and state of charge.
OVERCHARGED
RECHARGE
KC-0083C
1. Overcharge
2. Recharge
Portable Fire Extinguisher
Visual Distress Signals
All boats over 16 feet (4.8 meters) must have onboard day and
night visual distress signals when operating on coastal waters, the
Great Lakes, territorial seas or those waters directly connected to
them, up to a point where the body of water is less than two miles
wide. Carry several types of signaling devices to handle a variety of
conditions. Your Nautique dealer can help you select appropriate
visual distress signals for your area.
1-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-19
B o a t in g S a f e t y
If you are required to carry distress signals, you must have three
USCG approved pyrotechnic devices. Be sure they are in
serviceable condition, not exceeding the expiration date and
stored in a cool, dry location in a waterproof container. Have
enough signals on board to last three days.
!
Pyrotechnic signaling devices can cause
fire and / or explosion, death, serious injury and
property damage if improperly handled. Follow the
manufacturerʼs directions.
VISUAL DISTRESS SIGNALS
RED DISTRESS FLARE
(HAND)
ORANGE
FLAG
USE DAY AND NIGHT
USE
USE DAY ONLY
DAY
ONLY
ORANGE SMOKE
SIGNAL (HAND)
ARMS SIGNALS
(USE BRIGHT CLOTH)
RED METEOR FLARE
USE DAY AND NIGHT
USE DAY ONLY
ELECTRIC
DISTRESS
LIGHT
DYE MARKER
USE DAY ONLY
USE NIGHT ONLY
KC-0082
1-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-20
S e c t io n 1
R e c o m m e n d e d S a f e t y
E q u ip m e n t
As a precaution, a good boater will avoid potential problems on an
outing by having additional equipment on board. Normally, this
equipment is dependent on the body of water and the length of the
trip; your Nautique dealer can assist you:
• First aid kit and manual
• Anchor with at least 75 feet
(23 meters) of line
• Mooring lines and fenders
• Bailing device (bucket,
hand pump)
• Combination oar/ boat
hook
• Local charts and compass
• Day/ night distress signals
• Waterproof flashlight and
spare batteries
• Cellular phone
• Binoculars
• Portable AM/ FM radio with
weather band
• Lubricant
• Tool kit
• Spare propeller and
mounting hardware
• Spare fuses
• Spare keys
• Sunglasses and sun block
KC-0090
lotion
1-2 0
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-21
B o a t in g S a f e t y
E m e r g e n c y S t o p S w it c h a n d
L a n y a r d
Your Nautique boat is equipped with an emergency stop switch and
lanyard. Nautiques by Correct Craft strongly recommends that the
lanyard be secured to the operator and the lock plate attached to
the emergency stop switch prior to starting the engine and anytime
the engine is operating.
The lanyard is designed to turn off the engine whenever the
operator moves far enough away from the helm to activate the
switch. It is strongly recommended that the lanyard be used by the
operator.
!
An Emergency Stop Switch system that is
not used or does not function properly can cause death
or serious injury. DO NOT operate the boat if the
Emergency Stop Switch system does not function
properly.
• Attach the emergency stop switch lanyard to a secure place on
your clothing, your arm or leg while operating.
• DO NOT attach the lanyard to clothing that could tear loose.
DO NOT route the lanyard where it could become entangled,
preventing it from functioning.
• Avoid accidentally pulling the lanyard during normal operation.
Loss of engine power means loss of most steering control. Also,
without engine power, the boat could slow rapidly. This could
cause people and objects in the boat to be thrown forward.
There are practical limitations to what the emergency stop switch
and lanyard can do. It can take several seconds for the engine and
propeller to stop turning. The boat can continue to coast for
several hundred feet depending on the velocity at the time the
switch was activated, and the degree of any turn. While the boat is
coasting, it can cause injury to anyone in its path as seriously as if
the boat operated under power.
1-2 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-22
S e c t io n 1
Replacement lanyards should be of sufficient length to avoid
inadvertent activation. Accidental loss of power can be hazardous
particularly when docking or in heavy seas, strong current or high
winds.
E m e r g e n c ie s
Be prepared to deal with emergencies before they happen. Try to
formulate a plan for each type in advance so that decisions can be
made quickly and without hesitation. Precious moments lost can
mean the difference between losing and saving a life.
Fire/Explosion
You must be prepared and act quickly when dealing with a fire. It is
not recommended to battle a fire for an extended period of time.
Turn engines off and abandon the boat if the fire cannot be
extinguished quickly. Swim at least 25 yards (23 meters) upwind
from the boat and use the visual distress signals to get assistance.
!
Burn hazard from gasoline floating on
water which is ignited can cause death or serious injury.
Gasoline will float on top of water and can burn. If the
boat is abandoned, swim upwind, far enough to avoid
fuel that can spread over the surface of the water.
Onboard fires involving the fuel system usually result in either an
explosion that completely destroys the boat, or the boat burning to
the waterline and self-extinguishing. Deciding on abandoning the
boat or staying to fight the fire is difficult and depends on many
factors. Try to formulate a fire plan in advance to help make that
decision quickly and without hesitation.
Be sure to:
• Use caution and do not smoke when refueling.
• Verify that fuel does not leak.
• Use only marine approved equipment on your boat.
1-2 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-23
B o a t in g S a f e t y
Capsizing and Swamping
A boat may capsize or swamp when least expected. Like fires, try to
formulate a plan in advance on what to do if it should happen.
Keep in mind the following guidelines:
• Try to turn the engine OFF to prevent damage.
• If others were on board, try to locate them, make sure they
are conscious and that they can swim.
• Stay with the boat, it will float! Climb up on the hull and try
to get assistance.
• Do not try to swim to shore. It is usually farther than it looks.
If a leak is discovered, immediately determine the cause. A collision
with an underwater object could cause the hull to develop a leak. A
loose fitting or hose clamp on a piece of equipment could cause a
leak. Try to repair the leak if possible. If a leak is threatening the
safety of you and your passengers, call or signal for assistance.
Collisions
If a collision occurs, immediately account for all passengers. Assess
the hull for damage and activate the bilge pumps to reduce any
water intake. Try to operate the boat to keep the damaged area
above water. If necessary, call or signal for assistance.
Grounding
In the event you run aground, assess the situation before
proceeding. Immediately stop any water from entering the boat.
Inspect the rudder and rudder control system, the hull, propeller
and strut for damage. Maneuver the boat to safe water only if the
hull and all operating systems are in satisfactory operating
condition. Otherwise, call or signal for assistance.
Water Rescue (Man Overboard)
Immediately react to a person who has fallen overboard. Keep the
victim constantly in your sight. Safely return to the victim as soon as
possible. Throw the person a life preserver. Turn off the engine and
help the person into the boat.
1-2 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-24
S e c t io n 1
Medical Emergency
Be prepared in the event of an emergency. Know how to use your
first aid kit. Be aware of any special medical conditions of your
passengers.
Operation Failure
If you experience a propulsion, steering or control failure,
immediately turn OFF the engine. Try to determine the failure and
repair, if possible. Otherwise, call or signal for assistance.
H a z a r d o u s C o n d it io n s
Every waterway poses hazards that you should avoid, such as shallow
water, tree stumps and sand bars. Ask local boaters for information
and consult a marine chart when boating on unfamiliar waters. As
the operator of the boat, you should try to avoid all hazards, known
and unknown. The following information does not contain all
possible water hazards.
Shallow Water Operation
Operating in shallow water presents a number of hazards. If a
vibration is noticed after striking an object, it may indicate a
damaged propeller shaft or propeller.
Sand bars in narrow inlets are constantly shifting, making it difficult
to mark them with buoys. Tides in coastal areas affect water levels
producing sand bars. Sometimes sand bars are indicated by waves
as they form into breakers when passing over the sand bar. Refer to
Grounding, in this section, if you run aground on a sand bar.
Weeds
Weeds are generally a threat to your boat’s engine. Weeds on the
propeller may cause a vibration. They may also restrict water intake
causing the engine to overheat. If you run into weeds, stop the
engine and clear the propeller and water intakes completely of
weeds. Refer to your engine Operator’s Manual for additional
information.
1-2 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-25
B o a t in g S a f e t y
NOTICE
Weeds can sometimes be removed by shifting to NEUTRAL,
pausing for a moment, then shifting to REVERSE to unwind the
weeds from the propeller.
Dam Spillways
The water level around a dam spillway is a hazardous area. It is
subject to rapid changes caused by currents and turbulence. Keep
clear of the spillway areas below dams.
Weather/Seas
Getting caught in severe weather is hazardous. It is recommended
to check the weather, sea and wind conditions not only before, but
also periodically while you are boating.
A change in wave height, wind direction and speed indicates
deteriorating weather. Take common sense precautions if you are
forced to operate your boat in stormy conditions:
• Wear PFDs.
• Reduce speed and head for a safe place that you can easily
reach.
• If you lose power, keep the boat headed into the waves by
using the anchor.
It is best to avoid operating your boat in foggy weather. When fog
sets in take bearings and log courses and speeds. You are required
to emit a five-second blast from your horn or whistle once every
minute. Additionally, have passengers wear PFDs and observe for
oncoming watercrafts.
1-2 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-26
S e c t io n 1
Warning Markers
DIVERS FLAG
ALPHA FLAG
DISTRESS FLAG
RED
BLUE
ORANGE
USED BY
RECREATIONAL
DIVERS -
WORLDWIDE VESSELS
ENGAGED IN DIVING
OPERATIONS - DOES
NOT INDICATE
INDICATES
FELLOW
BOATER IS IN
NEED OF
INDICATES
DIVER'S
DIVER'S POSITION
ASSISTANCE
POSITION
KC-0352C-a
Warning Markers
It is a good idea to ask local authorities if there are hazardous areas
and how they are marked. Boaters must also recognize the flag
designs, which indicate that skin divers are present and keep well
clear of the area.
KC-0250C
Skin Diver Warning Flag
Watch for swimmers. Swimming areas may not be marked. Steer
clear from the area and remain alert.
1-2 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-27
B o a t in g S a f e t y
KC-0260C
Swim Area Warning Buoy
Navigation markers serve as a means of identifying navigable
routes, and indicate water hazards. Boaters should become familiar
with navigation markers and stay within marked boundaries and
clear of hazards.
C a r b o n M o n o x id e
Carbon Monoxide (CO) is a colorless and odorless gas
produced by all engines and fuel burning appliances. Even
!
with the best boat design and construction, plus the
utmost care in inspection, operation and maintenance, hazardous
levels of CO may still be present in occupied spaces under certain
conditions.
!
!
Exposure to carbon monoxide (CO) can
cause death or serious injury. Gasoline engines produce
carbon monoxide (CO). CO is colorless, odorless and
dangerous.
Direct and prolonged exposure to CO will cause brain
damage or death. Signs of exposure to CO include
nausea, dizziness and drowsiness. Avoid exposure to
yourself and / or your passengers to carbon monoxide.
Have a suspected CO victim deeply breathe fresh air and
immediately seek medical attention.
1-2 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-28
S e c t io n 1
O u r E n v ir o n m e n t
As a boater, you already appreciate nature’s beauty and the peace
of the great outdoors. It is a boater’s responsibility to protect the
natural environment by keeping waterways clean.
Foreign Species
If you trailer your boat from lake to lake, you may unknowingly
introduce a foreign aquatic species from one lake to the next.
Thoroughly clean the boat and trailer below the water line, remove
all weeds and algae, and drain the bilge and ballast tanks before
launching the boat in a new body of water.
Fuel/Oil Spillage
!
Fire or explosion hazard from fumes
accumulating from rags being stored in bilge area. DO
NOT store rags used to wipe up fuel or solvent spills in
the boat. Dispose of rags properly ashore.
The spilling of fuel or oil into our waterways contaminates the
environment and is dangerous to wildlife. DO NOT discharge or
dispose of fuel, oil or other chemicals into the water; it is prohibited
and you can be fined. These are three common, accidental types of
discharge:
• During initial fueling of a nearly empty tank
• Overfilling the fuel tanks
• Pumping contaminated bilge water
1-2 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-29
B o a t in g S a f e t y
If the fuel tank is near empty, start fueling the tank very slowly to
prevent accidental discharge. Once several gallons have been
added, the fueling rate can be increased to normal.
Avoid overfilling of the tank by monitoring the fuel level gauge
while fueling. Turn on the ignition without starting the engine and
monitor the gauge. Stop fueling as the gauge approaches the ‘full’
level and turn off the ignition when finished.
Discharge/Disposal of Waste
Waste means all forms of garbage, plastics, recyclables, food, wood,
detergents, sewage and even fish parts in certain waters – in short,
nearly everything. We recommend you bring back everything you
take out with you for proper disposal ashore.
Excessive Noise
Noise means engine noise, radio noise or even voices. Many bodies
of water have adopted noise limits. Music and loud conversation
can carry a considerable distance on water, especially at night. Be
sure to follow regulations and be courteous.
Wake/Wash
Be alert for NO WAKE zones. Prior to entering a no wake zone,
come off plane to the slowest steerable speed. Use caution when
operating around smaller crafts, in channels and marinas, and in
congested areas.
Exhaust Emissions
Increased exhaust (hydrocarbon) emissions pollute our water and
air. Keep your engine tuned and boat hull clean for peak
performance. Consult your Nautique dealer for information.
Paints
If your boat is kept in water where marine growth is a problem, the
use of anti-fouling paint may reduce the growth rate. Be aware of
environmental regulations that may govern your paint choice.
Contact your local boating authorities for information.
1-2 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-30
S e c t io n 1
Cleaning Agents
Household cleaners should be used sparingly and not discharged
into waterways. DO NOT mix cleaners and be sure to use plenty of
ventilation in enclosed areas. DO NOT use products which contain
phosphates, chlorine, solvents, non-biodegradable or petroleum
based products. Citrus-based cleaners are excellent for marine
cleaning purposes and are safe for you and the environment.
MARPOL Treaty
The USCG enforces the International Convention for the
Prevention of Pollution from ships, commonly referred to as the
MARPOL Treaty (MARine POLlution). This treaty prohibits the
overboard dumping of all ship-generated plastics, chemicals,
garbage and oil.
W a t e r s p o r t S a f e t y
Skiers or riders are obligated to be aware of the same fundamental
safety rules as operators. If you are new to water skiing, seek
certified training before starting. You will find it especially helpful
to join a local ski club, World Wakeboard Association and/ or the
USA Water Ski, when possible.
Always remember that the majority of water skiing injuries are the
result of impacts with other objects. Always look where you are
going and be aware of what is going on around you.
Teak/Drag Surfing
READ, UNDERSTAND and be FAMILIAR with the information
contained on warning labels and adhere to the boat operation
practices described on them. The United States Coast Guard issued
a SAFETY ALERT on August 28, 2001 that covers some of the issues
of improper use of the boarding platform. The SAFETY ALERT
and portions of the accompanying information follow:
1-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-31
B o a t in g S a f e t y
EXHAUST PORT
CORC023
Every year tragic deaths occur from the negligence of unsafe
boating and dangerous activities. Experts say, "many of these deaths
may have been caused by an invisible hazard, carbon monoxide
poisoning." Taking the risk of swimming under a boarding platform
when the engine is running, skiing within 20 feet (6.1 meters),
"teak surfing" or "dragging" behind a moving boat can be fatal.
Nautiques by Correct Craft DOES NOT consider any dangerous
activities which can result in a serious injury or death a watersport.
Nautiques by Correct Craft is concerned for all boaters’ safety and
DOES NOT promote unsafe boating risks or jeopardizing any
boaters’ safety.
DO NOT use the boarding platform for any other purpose than
boarding the boat or preparation of entering the water, and DO
NOT use the boarding platform when the engine is running.
1-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-32
S e c t io n 1
SAFETY ALERT From August 28, 2001:
The United States Coast Guard advised boaters not to "Teak/ Drag
Surf." Recent boating fatalities revealed that carbon monoxide
(CO) emitted from a vessel’s exhaust resulted in CO poisoning and
the death of at least six teak surfers. "Teak/ Drag Surfing" places the
individual in position directly exposed to the CO in the engine’s
exhaust. This may result in a loss of coherent responses and even
death. In addition, "Teak/ Drag Surfing" dangerously exposes the
individual to a possible propeller injury, and since it is done without
a life jacket (PFD), it significantly increases the probability of
drowning. Therefore, the Coast Guard stresses, "Teak/ Drag
Surfing" is a very dangerous activity and advises boaters not to
participate in it.
The Coast Guard pointed out that carbon monoxide is one of the
most dangerous gases. It strikes before you know you are exposed
and it impairs in a way that can and too often does lead to death.
That is why it is so important to the Coast Guard that in every
circumstance where it can be avoided, it is.
General Watersport Precautions
• DO NOT ski in shallow water, close to shore or in water
where you do not know the depth or what is beneath the
surface.
• DO NOT put your arm, head or any other part of your body
through the handle-bridle of the ski line nor wrap the line
around any part of the body at any time.
• DO NOT ski at night or directly in front of other boats.
• DO NOT jump from a boat that is moving at any speed, nor
enter or exit the water when the engine is running (RUN).
• DO NOT approach the boat if the engine is running.
• DO NOT ski near swimming areas, beaches or personal
watercraft.
• DO NOT follow directly behind another boat or skier
without leaving an adequate safe distance.
• DO NOT "back up" to anyone in the water.
• DO NOT ski with multiple skiers with different length ropes.
• DO NOT ski in limited visibility conditions.
• DO NOT approach the rear of the boat while the engine is
running.
1-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-33
B o a t in g S a f e t y
• DO NOT Kitefly.
• Make sure that everyone knows and uses approved skiing
hand signals and common skiing courtesy.
• Be sure to turn off the engine before allowing anyone to
approach the boat.
• The engine MUST be shut down (OFF) before a skier enters
or exits the boat, boarding platform or ladder.
• Every skier MUST always wear a USCG-approved Type III
personal flotation device. Special PFDs are available for high
impact falls into the water.
• Maintain a distance of at least 100 feet from all other
objects, including other boats, piers, rafts, mooring and
navigational buoys, pilings, abutments or any other items.
• Be sure to have an experienced operator and observer in the
boat when skiing.
• Look before you turn the boat to pick up a fallen skier.
• Have ship to shore communication devices if operating at a
significant distance off shore.
• The operator should never retrieve or pick up an article
from the water while the engine is running. The engine
MUST be shut OFF.
• The operator should always keep the skier in view when the
skier is entering or exiting the boat.
• Communicate skiing speed with the skier before starting.
• The operator should know the ability level of the skier.
• The skier should indicate he/ she is clear of the boat prior to
starting the boat or putting the boat into gear and tightening
the rope.
• The operator, observer and skier should agree to
communication hand signals before starting.
• Observer in the boat should keep operator appraised of
skier status.
• The operator should always watch the skier as the line is
tightened to start (in case rope wraps around ski or skier).
• The operator should look ahead before starting.
• Start from a safe place with good forward and peripheral
visibility.
• The operator should check direction of the rudder before
starting (in gear, slowly making sure the boat goes straight).
1-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-34
S e c t io n 1
• The operator should be primarily aware of what is occurring
in front of the boat, but be aware of skier’s progress.
• Be sure to inspect the tow eye or pylon before use. If there is
any evidence of corrosion or other damage, do not use until
it has been inspected by your Nautique dealer.
• Be sure to wear wet suits or protective shorts when skiing to
prevent abrasions, hypothermia and injuries to orifices
(rectal and vaginal) from impact with a water surface.
• When people are getting on or off of watersports
equipment, always turn the engine off. If boarding
watersports equipment from the boat, always do so from the
boarding platform.
• Always inspect watersports equipment for wear, fraying, etc.,
before use. DO NOT use if they show signs of wear or
fraying.
• When approaching a skier, always turn the engine off before
allowing the skier to come onboard. This will keep a
propeller that is rotating under engine power from injuring
the skier.
• Be sure to approach a downed skier on the operator’s side,
keep the skier always in view.
• Display a skier down flag whenever the skier is in the water
and not skiing.
• Inspect towline for fraying, unnecessary knots or cuts.
Replace when the rope shows signs of wear. DO NOT wait
for the rope to break before replacing an old rope.
• Be sure to follow the approved towing pattern on each lake.
1-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-35
B o a t in g S a f e t y
When participating in watersports, be safe and courteous and
follow these guidelines:
• Be considerate to fishermen and others you share the water
with.
• DO NOT perform watersports in congested areas.
• Stay away from navigation markers.
• Stay away from other boats and watersports participants.
CUT ENGINE
BACK
TO DOCK
CIRCLE
SPEED FASTER
SPEED SLOWER
SPEED OK
STOP
TURN LEFT
SKIER IN WATER
TURN RIGHT
SKIERS O.K.
KC-0271C-a
Water Sport Hand Signals
Watersports Responsibility Code
Be aware that there are elements of risk in boating, skiing and
riding that common sense and personal awareness can help reduce.
Know your ability level and stay within it.
To increase your enjoyment of the sport follow the “Watersports
Responsibility Code.”
It is your responsibility to:
• Familiarize yourself with all applicable laws, the risks
inherent in the sport and the proper use of equipment.
• Know the waterways where you will be skiing or riding.
• DO NOT ski or ride in shallow water, near shore, docks,
pilings, swimmers or other watercraft.
• Always have a person other than the boat driver as an
observer and agree on hand signals before starting.
• Always wear a U.S. Coast Guard type III (PFD) vest.
1-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 1_2008.qxd:Naut Air Sec 1.qxd 6/24/08 3:05 PM Page 1-36
S e c t io n 1
• Read your owner’s manual and inspect your equipment prior
to use.
• Ski or ride within your limits.
• Always ski or ride in control and at speeds appropriate for
your ability.
• Always turn ignition off when anyone is near watercraft
power drive unit.
• Avoid CO poisoning!
• Never drag within 20 feet (6.1 m) behind a moving
watercraft.
• DO NOT operate watercraft, ski or ride under the influence
of alcohol or drugs.
1-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 2_2008.qxd:Naut Air Sec 2.qxd 6/24/08 3:08 PM Page 2-1
S e c t io n 2
B a s ic R u le s o f t h e R o a d
!
Hazard from collisions between boats can
cause death or serious injury. Follow the nautical “Rules
of the Road.”
The operator is legally required to follow the rules. The following
information outlines only the most basic of the nautical “Rules of
the Road.” For more information, contact your local USCG
Auxiliary.
A id s T o N a v ig a t io n
Learn to recognize the different buoys and day markers; they are
the signposts of the waterways. There are two primary marking
systems in use in the U.S.: the Uniform State Waterway Marking
System (USWMS), used on inland waters and maintained by each
state, and the Federal Waterway Marking System (FWMS), used on
coastal waters and rivers and maintained by the USCG. In addition,
the FWMS has two modified systems: the Western River Buoyage,
and the Intercoastal Waterway Buoyage. Be sure to check with local
authorities on the buoyage system in use.
The type of hazard/ warning buoys and markers depends on the
area of jurisdiction. Check with local boating authorities.
The only buoys you are permitted to moor to are mooring buoys.
Mooring to a navigation buoy or other navigational aid or
regulatory marker is illegal.
2 -1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 2_2008.qxd:Naut Air Sec 2.qxd 6/24/08 3:08 PM Page 2-2
S e c t io n 2
BLUE
KC-0412C
Mooring Buoy – White with Blue Band
May Show White Reflector or Light
USWMS System
In the USWMS Lateral System, well-defined channels are marked
with red and black buoys. Lateral means the sides of the channel
are marked and the boat should pass between them.
The USWMS Cardinal System is used when there is no well-defined
channel or where an obstruction may be approached from more
than one direction. With the cardinal system:
• Pass north or east of BLACK-TOPPED WHITE buoy.
• Pass south or west of RED-TOPPED WHITE buoy.
• RED and WHITE VERTICALLY STRIPED buoy indicates
boat should pass outside of the buoy (away from shore).
2 -2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 2_2008.qxd:Naut Air Sec 2.qxd 6/24/08 3:08 PM Page 2-3
B a s ic R u le s o f t h e R o a d
Uniform State Regulatory Markers
USWMS regulatory markers are white with international orange
geometric shapes; you must obey regulatory markers.
UNIFORM STATE WATERWAY MARKING SYSTEM (USWMS)
CONTROLLED
AREA
DANGER
BOATS
KEEP OUT
INFORMATION
DO NOT PASS
BETWEEN SHORE
AND BUOY
SPECIAL
PURPOSE
NAVIGATE TO
STARBOARD
FACING UPSTREAM
NAVIGATE TO
PORT FACING
UPSTREAM
NAVIGATE TO
SOUTH OR WEST
NAVIGATE TO
NORTH OR EAST
MID-CHANNEL
KC-0411C
Uniform State Waterway Marking System (USWMS)
FWMS System
The FWMS Lateral System is for use on navigable waters except
Western Rivers and Intercoastal Waterways.
The markings on these buoys are oriented from the perspective of
being entered from seaward (the boater is going toward the port).
This means that red buoys are passed on the starboard (right) side
of the vessel when proceeding from open water into port, and
green buoys to the port (left) side.
The right side (starboard) of the channel is marked with RED, even
numbered buoys. The left (port) side of the channel is marked with
GREEN, odd numbered buoys.
2 -3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 2_2008.qxd:Naut Air Sec 2.qxd 6/24/08 3:08 PM Page 2-4
S e c t io n 2
UNLIGHTED
BELL BUOY
SPAR BUOY
CAN BUOY
LIGHTED BUOY
NUN BUOY
KC-0420
FWMS Marking System
The middle of the channel is marked with RED and WHITE
vertically striped buoys; pass close to these buoys.
RED
SPHERICAL SAFE
WATER MARKER
KC-0430
Spherical Safe Water Marker
Obstructions, channel junctions, etc. are marked with RED and
GREEN horizontally striped buoys.
A RED band at the top means the preferred channel is to the left
of the buoy; a GREEN top band means the preferred channel is to
the right of the buoy.
Day markers are colored and numbered the same as buoys. RED,
triangular day markers with even numbers mark the starboard side
of the channel. GREEN, square day markers with odd numbers
mark the port side of the channel.
2 -4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 2_2008.qxd:Naut Air Sec 2.qxd 6/24/08 3:08 PM Page 2-5
B a s ic R u le s o f t h e R o a d
STARBOARD
DAY
RED
MARKER
PORT
DAY
GREEN
MARKER
KC-0440C
Lights, bells and horns are used on buoys for night or poor visibility
conditions. Buoys with unique light flashing characteristics are
identified on nautical charts with the specific flashing pattern.
R ig h t o f W a y
NOTICE
In general, boats with less maneuverability have right of way over
more agile crafts. You must stay clear of the vessel with right of
way and pass to his stern.
Privileged Boats
Privileged boats have right of way and can hold course and speed.
Sailboats and boats paddled or rowed have the right of way over
motor boats. Sailboats under power are considered motorboats.
Small pleasure craft must yield to large commercial boats in narrow
channels.
Burdened Boats
The burdened boat is the boat that must make whatever adjustment
to course and speed necessary to keep out of the way of the
privileged boat.
2 -5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 2_2008.qxd:Naut Air Sec 2.qxd 6/24/08 3:08 PM Page 2-6
S e c t io n 2
Crossing Situation
In crossing situations, the boat to the right from the 12 o’clock to
the 4 o’clock position has the right of way. It must hold course and
speed. The burdened boat keeps clear and passes behind the
privileged boat. Boats going up and down a river have the privilege
over boats crossing the river.
12 O'CLOCK
STAND-ON
(PRIVILEGED)
VESSEL
DANGER ZONE
GIVE-WAY
(BURDENED)
VESSEL
4 O'CLOCK
CORC017
Crossing
2 -6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 2_2008.qxd:Naut Air Sec 2.qxd 6/24/08 3:08 PM Page 2-7
B a s ic R u le s o f t h e R o a d
Meeting Head-On
Neither boat has the right of way in this situation. Both boats should
decrease speed, turn to the right and pass port-to-port. However, if
both boats are on the left side of the channel, each vessel should
sound two short blasts and pass starboard-to-starboard.
HONK
HONK
HONK
HONK
HONK
HONK
MEETING
HEAD TO
HEAD
PASSING
PORT TO
PORT
PASSING
STARBOARD TO
STARBOARD
CORC018
Meeting Head-On
2 -7
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 2_2008.qxd:Naut Air Sec 2.qxd 6/24/08 3:08 PM Page 2-8
S e c t io n 2
Overtaking
The boat that is overtaking one ahead of it is the give-way boat and
must make any adjustments necessary to keep out of the way of the
stand-on boat. The stand-on boat should hold its course and speed.
HONK
(LONG)
STAND-ON
(PRIVILEGED)
VESSEL BEING
OVERTAKEN
HONK
(LONG)
GIVE-WAY
(BURDENED)
VESSEL
OVERTAKING
CORC019
Overtaking
2 -8
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 2_2008.qxd:Naut Air Sec 2.qxd 6/24/08 3:08 PM Page 2-9
B a s ic R u le s o f t h e R o a d
The General Prudential Rule
The General Prudential Rule regarding right of way, is that if a
collision appears unavoidable, neither boat has right of way. As
prescribed in the "Rules of the Road," both boats must act to avoid
collision.
Night Running
Boats operating between sunset and sunrise (hours vary by state)
must use navigational lights. Nighttime operation, especially during
bad weather or fog can be dangerous. All "Rules of the Road" apply
at night, but it is best to slow down and stay clear of all boats,
regardless of who has right of way. Protect your night vision by
avoiding bright lights and have a passenger, if possible, help keep
watch for other boats, water hazards and aids to navigation.
2 -9
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 2_2008.qxd:Naut Air Sec 2.qxd 6/24/08 3:08 PM Page 2-10
S e c t io n 2
N O T E S
2 -10
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 1
Section 3
210, 211, 220, 230
and 236
Specifications
210
Length Overall ........................................................21’ 0" (6.40 m)
Length with Platform...........................................23’ 3.5" (7.10 m)
Lifting Ring Spacing...............................................19’ 7" (5.97 m)
Beam.............................................................................98" (2.49 m)
Draft..............................................................................28" (0.71 m)
Approximate Dry Weight*..............................3,800 lbs (1,725 kg)
Fuel Capacity..................................................40 Gallons (151.4 L)
Maximum Capacity .........................12 People (1,850 lbs/839 kg)
Horsepower Range..........................................................343 to 390
Gear Reduction Ratio.............................................................1.48:1
Maximum Factory Ballast Capacity......................906 lbs (411 kg)
* Weights are estimates and can vary from options and equipment
added.
211
Length Overall ........................................................20’ 9" (6.32 m)
Length with Platform..............................................23’ 1" (7.04 m)
Lifting Ring Spacing...............................................19’ 8" (5.99 m)
Beam.............................................................................93" (2.36 m)
Draft..............................................................................28" (0.71 m)
Approximate Dry Weight*..............................3,500 lbs (1,589 kg)
Fuel Capacity..................................................38 Gallons (143.8 L)
Maximum Capacity .........................10 People (1,350 lbs/612 kg)
Horsepower Range..........................................................275 to 390
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 2
Section 3
Gear Reduction Ratio.............................................................1.48:1
Maximum Factory Ballast Capacity......................625 lbs (284 kg)
* Weights are estimates and can vary from options and equipment
added.
220
Length Overall ........................................................22’ 1" (6.73 m)
Length with Platform..............................................24’ 3" (7.39 m)
Lifting Ring Spacing..........................................20’ 7.25" (6.28 m)
Beam.............................................................................96" (2.44 m)
Draft..............................................................................29" (0.74 m)
Approximate Dry Weight*..............................4,070 lbs (1,847 kg)
Fuel Capacity..................................................51 Gallons (193.1 L)
Maximum Capacity .........................14 people (2,050 lbs/930 kg)
Horsepower Range..........................................................343 to 390
Gear Reduction Ratio.............................................................1.48:1
Maximum Factory Ballast Capacity......................849 lbs (385 kg)
* Weights are estimates and can vary from options and equipment
added.
230, 236
Length Overall .....................................................23’ 1.5" (7.05 m)
Length with Platform...........................................25’ 4.5" (7.73 m)
Lifting Ring Spacing..........................................22’ 0.25" (6.71 m)
Beam........................................................................100.5" (2.55 m)
Draft..............................................................................29" (0.74 m)
Approximate Dry Weight*..............................4,300 lbs (1,952 kg)
Fuel Capacity..................................................51 Gallons (193.1 L)
Maximum Capacity......................16 People (2,300 lbs/1,043 kg)
Horsepower Range..........................................................343 to 390
Gear Reduction Ratio.............................................................1.48:1
Maximum Factory Ballast Capacity......................791 lbs (359 kg)
* Weights are estimates and can vary from options and equipment
added.
NOTICE
The dash configurations used in this section may show more features
than what is included in your Nautique.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 3
210, 211, 220, 230 and 236
4
5
6
8
7
9
10
3
11
2
12
13
14
15
1/2
E
F
1
WATER
1/2
E
F
WATER
1/2
E
F
WATER
16
17
20
19
18
CORC140
211, 220 Dash Pod and
Console
1. Digital Stereo Remote w/Clock
2. Tachometer
3. Nautique Cruise
4. Check Engine Light
5. Speedometer
6. Service Soon Light (catanium engine only)
7. Fuel
8. Oil
9. Engine Temperature Gauge
10. Voltage Gauge
11. Ignition and Switch Panel – refer to Ignition and Switch Panel in this
section
12. 12-Volt Port
13. Shifter/Throttle Control Handle
14. SportShift™ Hydro-Gate™ Control Handle
15. Shift Safety Lock-out Umbrella
16. Neutral Warm-up Button
17. Emergency Stop Switch
18. Ballast Tank(s) Level Gauges
19. Automatic Bilge Panel
20. Steering Wheel Tilt Lever
NOTICE
A full description of the gauges and switches and their functions is
discussed in Section 4, Smart Pod – Limited or Team and
Ignition and Switch Panel.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 4
Section 3
8 9
10
7
6
5
4
3
2
11
12
13
Se
12V
S
T
A
RT
220
0
1
4
220
0
CO
147
RRE
CT
C
RAF
00
A
ORL
ERO
T
,
E
i
39
qu
AND
S
P
A
C
I
N
O
,
F
PKY
14
N
L
a
3
u
2
t
e
23
6
20
1
19
18
17 16
15
CORC208
210, 230 and 236 Dash Pod
and Console
1. Digital Stereo Remote w/Clock
2. Speedometer
3. Oil
4. Fuel
5. Check Engine Light
6. Tachometer
7. Service Soon Light (catanium engine only)
8. Voltage Gauge
9. Engine Temperature Gauge
10. Nautique Cruise
12. Ignition and Switch Panel – refer to Ignition and Switch Panel in this
section
12. Fire Extinguisher System – Optional
13. SportShift™ Hydro-Gate™ Control Handle
14. Emergency Stop Switch
15. Shifter/Throttle Control Handle
16. Shift Safety Lock-Out Umbrella
17. Neutral Warm-Up Button
18. Automatic Bilge Panel
19. Ballast Tank(s) Level Gauges
20. Steering Wheel Tilt Lever
NOTICE
A full description of the gauges and switches and their functions is
discussed in Section 4.
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 5
210, 211, 220, 230 and 236
5
6
4
7
8
3
9
2
10
11
1
13
12
CORC083
Ignition and Switch Panel
1. Keyless Ignition Key Pad
2. Belly Ballast (if equipped)
3. Port Ballast (if equipped)
4. Starboard Ballast (if equipped)
5. Underwater Lights
6. Heater Fan
7. Courtesy Lights/Docking lights
8. Navigation Lights/Anchor Light
9. Bilge Pumps
10. Engine Compartment/Bilge Area Blower
11. Horn
12. System Indicator Light
13. Ignition Indicator Light
NOTICE
If your boat is not equipped with the features on the Ignition and
Switch Panel Switch buttons, the button will not have a function.
A full description of the key pad keys and switch buttons and their
functions is discussed in Section 4, Smart Pod - Limited or
Team, Control Switches and Ballast Tank Control Switches.
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 6
Section 3
Keys
1
2
CORC027
1. Fuel Tank Fill Cap Key
2. Hatch Latch Key
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 7
210, 211, 220, 230 and 236
NOTES
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 8
Section 3
210 Deck Layout
1
30
2
3
29
27
4
5
6
26
7
25
24
8
28
23
22
10
9
10
3
21
11
12
13
14
20
31
15
16
17
CORC214
19
18
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 9
210, 211, 220, 230 and 236
210
Description
1. Bow Navigation Light
2. 12V Port
3. Bilge Pump Outlet
4. Belly Tank Vent
5. Dash Pod & Console
6. Sport Shift
7. Automatic Bilge Panel
8. Storage
9. Anchor Light Receptacle
10. Fuel Tank Fill
11. Starboard Ballast Tank Vent
12. Engine Cooling Water Intake Strainer
13. Storage Hatch Latch
14. Storage Trunk
15. Rudder Shaft Remote Lube Fitting
16. Boarding Platform
17. Stern Lifting Ring or Pop-Up Pylon or Lift Ring Pop-Up Pylon
Combo
18. Engine Cover Latch
19. Engine Cooling Water Intake Shut-off Valve
20. Starboard/Port Ballast Tank Water Intake/Drain Valves/Belly Tank
Water Intake/Drain Valve
21. Port Ballast Tank Vent
22. Fuel Tank Vent
23. Flight Control Tower Watersports Tow Point
24. Aft Facing Flip Up Seat
25. Flight Control Tower
26. Operator’s Pedestal Seat Adjustment
27. Love/Observers Seat/Storage Access
28. Flight Control Tower Anchor Light
29. Glove Box/Stereo/Auxiliary Input/12V Port
30. Bow Lifting Ring
31. Battery Selector Switch
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 10
Section 3
211 Deck Layout
1
2
3
4
22
29
5
6
7
28
27
26
25
8
22
9
24
10
23
11
22
21
30
20
11
12
13
4
14
15
16
19
18
17
CORC141
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 11
210, 211, 220, 230 and 236
211
Description
1. Bow Navigation Light
2. Bow Lifting Ring
3. 12V Port
4. Bilge Pump Outlet
5. Belly Tank Vent
6. Dash Pod and Console
7. Hydro-Gate™ Control and SportShift
8. Automatic Bilge Panel
9. Built-in Cooler
®
10. Anchor Light Receptacle (not included with Flight Control Tower
option)
11. Fuel Tank Fill
12. Engine Cooling Water Intake Strainer
13. Storage Hatch Latch
14. Starboard Ballast Tank Vent
15. Storage Trunk/Anchor Light Storage
16. Rudder Shaft Remote Lube Fitting
17. Boarding Platform
18. Engine Cover Latch
19. Port Ballast Tank Vent
20. Engine Cooling Water Intake Shutoff Valve
21. Starboard and Port Ballast Tank Water Intake/Drain Valves/Belly
Tank Water Intake/Drain Valve
22. Storage
23. Fuel Tank Vent
24. Watersports Tow Point
®
25. Flight Control Tower
26. Love Seat/Storage Access/Cooler
27. Operator’s Pedestal Seat Adjustment
28. Flight Clips™
29. Glove Box/Stereo/Auxiliary Input/12V Port
30. Battery Selector Switch
The primary battery is located in the port/aft storage compartment, below
the storage hatch latch. The optional secondary battery and the optional
battery selector switch are located in the forward portion of the Storage
Trunk/Anchor Light Storage trunk. The optional battery selector switch
is located next to the primary battery.
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 12
Section 3
220 Deck Layout
1
33
2
9
32
31
3
4
5
30
6
29
9
28
7
8
27
26
9
9
25
11
10
11
3
12
24
13
23
22
14
34
14
15
16
17
21
20
19
18
CORC172
3-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 13
210, 211, 220, 230 and 236
220
Description
1. Bow Navigation Light
2. 12V Port
3. Bilge Pump Outlet
4. Belly Tank Vent
5. Dash Pod and Console
6. Hydro-Gate™ Control and SportShift
7. Automatic Bilge Panel
8. Built-in Trash Receptacle Holder/Tower Step
9. Storage
®
10. Anchor Light Receptacle (not included with Flight Control Tower
option)
11. Fuel Tank Fill
12. Starboard Ballast Tank Vent
13. Engine Cooling Water Intake Strainer
14. Storage Hatch Latch
15. Storage Trunk/Anchor Light Storage
16. Rudder Shaft Remote Lube Fitting
17. Boarding Platform
18. Stern Lifting Ring or Pop-Up Pylon or Lift Ring Pop-Up Pylon
Combo
19. Storage Tray Rear Access Hatch
20. Storage Tray
21. Storage Tray/Engine Cover Latch
22. Engine Cooling Water Intake Shut-off Valve
23. Starboard and Port Ballast Tank Water Intake/Drain Valves/Belly
Tank Water Intake/Drain Valve
24. Port Ballast Tank Vent
25. Fuel Tank Vent
®
26. Flight Control Tower Watersports Tow Point
27. Built-in Cooler/Storage/Tower Step
®
28. Flight Control Tower
29. Operator’s Pedestal Seat Adjustment
30. Love/Observer’s Seat/Storage Access/Removable Cooler
®
31. Flight Control Tower Anchor Light
32. Glove Box/Stereo/Auxiliary Input/12V Port
33. Bow Lifting Ring
34. Battery Selector Switch
The primary battery is located in the port, aft, cockpit storage
compartment, in front of the aft jump seat, below the seat. The optional
secondary battery is located opposite of the primary battery. The optional
battery selector switch is located next to the primary battery.
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 14
Section 3
230, 236 Deck Layout
1
2
3
4
5
3
26
6
3
7
25
8
9
24
10
11
23
12
12
4
13
14
22
15
15
16
18
21
19
18
15
20
17
CORC213
3-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 15
210, 211, 220, 230 and 236
230, 236
Description
1. Bow Navigation Light
2. Bow Lifting Ring
3. 12V Port
4. Bilge Pump Outlet
5. Belly Ballast Tank Vent
6. Dash Pod and Console
7. Hydro-Gate™ Control and SportShift
8. Removable Cooler
9. Engine Cooling Water Intake Shutoff Valve
10. Engine Cooling Water Intake Strainer
11. Battery
12. Fuel Tank Fill
13. Starboard Ballast Tank Vent
14. Battery Selector Switch
15. Trunk Storage Access
®
16. Anchor Light Receptacle (not included with Flight Control Tower
option)
17. Aft Built-In Cooler
18. Transom Lifting Eyes
19. Rudder Shaft Remote Lube Fitting
20. Pop-Up Water Sports Tow Point
21. Boarding Platform
22. Port Ballast Tank Vent
23. Fuel Tank Vent
24. Starboard and Port Ballast Tank Water Intake/Drain Valves/Belly
Tank Water Intake/Drain Valve
25. Love Seat/Storage Access
26. Glove Box/Stereo/Auxiliary Input/12V Port
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 3_2008.qxd:Naut Air Sec 3.qxd 6/25/08 4:26 PM Page 16
Section 3
Standard and Optional
Equipment
Nautique boats are equipped with only the finest standard and
optional equipment available. Your boat’s equipment will vary,
based on how your boat was built. Many options can only be
installed during the manufacturing of the boat and cannot be retro-
fitted to boats in the field.
Not all of the standard or optional equipment’s use, safety and
maintenance information can be covered in this manual. You will
find most of the standard and optional equipment in this manual
in the section pertaining to its use and function in Section 4. Make
sure you read and understand this manual and all the other
manufacturers’ literature provided in your Skipper’s Kit to
maximize the benefits and uses this equipment has to offer.
If you have any questions regarding the use of any equipment on
your Nautique boat, contact your Nautique dealer.
3-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 1
S e c t io n 4
C o n t r o ls a n d In d ic a t o r s
Knowing the systems, controls and indicators on your boat is
essential for safe and proper operation.
!
Improperly maintained controls are
hazardous and may cause sudden loss of control. Make
sure all steering and shift / throttle hardware, cables and
fluid levels are regularly inspected and maintained.
Improper maintenance may result in a loss of control,
possibly causing serious injury or death.
S t e e r in g
The steering system in your Nautique boat provides excellent
maneuvering performance for pleasure boating or during
watersports. Boat steering is not self-centering. Always keep a
secure grip on the steering wheel to maintain full boat control. The
steering wheel is equipped with a tilt lever to adjust the wheel angle
to a comfortable operating position when the boat is not moving.
RELEASE
LEVER
CORC133
4 -1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 2
S e c t io n 4
The helm transfers rotary motion of the steering wheel to linear
motion in the cable which pushes or pulls the rudder. Nautique
rudders are equipped with an adjustable trim tab under license
from Z-Marine (U.S. patent 5,746,147) to compensate for the
torque generated by the propeller.
Maintenance for the steering system is minimal because there are
few serviceable parts. The rack and pinion for the system is
lubricated and sealed during manufacturing. It is the responsibility
of the owner/ operator to inspect the steering system frequently.
If you experience difficulty in steering, refer to Section 8 - Care and
Maintenance.
!
Hazard from improper maintenance of the
controls can cause death or serious injury from sudden
loss of control. DO NOT operate your boat if you
suspect the steering system or control are
H y d r o - G a t e ™ C o n t r o l a n d
S p o r t S h if t
The Hydro-Gate is engaged by moving the SportShift lever located
at the helm’s starboard side fore and disengaged by moving the
lever aft. When the SportShift lever is pushed forward, the Hydro-
Gate is engaged, creating maximum lift for a wake with a well-
defined crest and shallower ramp. When the SportShift lever is
pushed aft, the Hydro-Gate is disengaged (raised), allowing your
boat to sit deeper in the water, creating the maximum wake with a
steep ramp. The SportShift lever can be placed in any position to
create your ultimate wake. When used in conjunction with the
Launch Control System, the SportShift and the Hydro-Gate can be
used to create a wide variety of wakes to meet your style and need.
The SportShift and Hydro-Gate can be used at any speed or at rest.
4 -2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 3
C o n t r o ls a n d In d ic a t o r s
R
A
D
O
B
E
K
A
W
CORC142B
CORC143
4 -3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 4
S e c t io n 4
S h if t e r / T h r o t t le
!
Hazard from replacing your shift/ throttle
control without a start-in-gear protection system can
cause death or serious injury, DO NOT replace the
control with a control that does not have this feature.
Your Nautique boat is equipped with a Shifter/ Throttle Control
Handle which features a start-in-gear protection to prevent the boat
from moving when started.
A single-lever control with neutral warm-up button and safety lock-
out umbrella operates as both a gear shifter and a throttle control.
When the throttle lever is vertical, it is locked in the NEUTRAL
position for safety. Be sure the control is in NEUTRAL before
attempting to start the engine. Lifting the safety lock-out umbrella
and moving the throttle lever forward will engage FORWARD gear
in the transmission and increase the engine RPM. Moving the
throttle lever backward will engage REVERSE gear in the
transmission and also increase the engine RPM.
NEUTRAL
FORWARD SHIFT
RANGE
REVERSE SHIFT RANGE
IDLE
IDLE
FORWARD
THROTTLE
RANGE
REVERSE
THROTTLE
RANGE
NEUTRAL
LOCKOUT
SAFETY LOCK-OUT
UMBRELLA
FULL
THROTTLE
FULL
THROTTLE
CORC0223
CAUTION
DO NOT shift too quickly from FORWARD to
REVERSE. Stay in NEUTRAL, or idle position until the
boat has lost most of its headway before completing the
shift to REVERSE or engine / transmission damage may
occur.
4 -4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 5
C o n t r o ls a n d In d ic a t o r s
Emergency Stop Switch
The emergency stop switch will stop the engine when the lanyard is
pulled far enough to disengage it from the switch. Attach the
lanyard to the boat operator whenever the engine is running but be
aware there will be a loss of engine power if the switch is activated.
If the operator is thrown from the seat, or moves too far from the
helm, the lanyard will become disconnected from the switch,
shutting off the engine. Refer to Section 1 for more information.
CAUTION
DO NOT allow your boat to be operated
without the proper use of the emergency stop switch
and lanyard.
EMERGENCY STOP SWITCH
CLIP
LANYARD
HOOK
CORC0224
To attach a lanyard, connect the clip to the emergency stop switch
and the hook to a strong piece of clothing on the operator, such as
a belt loop.
NOTICE
The engine will not start unless the emergency stop switch is
attached.
4 -5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 6
S e c t io n 4
!
Hazard from improper use of the
emergency stop switch can cause death or serious
injury. The emergency stop switch is designed to stop
the boat if the operator is accidentally thrown from the
helm. Attach the lanyard to the operator before starting
the engine.
The emergency stop switch can only be effective when it is in good
working condition.
Observe the following:
• DO NOT remove or modify an emergency stop switch
and/ or its lanyard.
• The lanyard must be free from obstructions that could
interfere with its operation.
Once a month: Check the emergency stop switch for proper
operation. With the engine running, pull lanyard. If the engine
does not stop, see your Nautique dealer for service of the switch.
S t a n d a r d D a s h P o d - 2 10 , 2 11
Gauges
• Volts - Indicates the condition of the engine’s cranking
battery in volts DC. With the ignition switch on and the
engine not running, a reading above 12.5 volts indicates a
fully charged battery. With the engine running at idle, the
gauge should read between 12.5 and 13 volts. With the
engine running at cruising speeds and above, it should show
13 to 14.5 volts. Have your Nautique dealer check the
charging system if the voltmeter reads outside these normal
ranges.
• Temp - Indicates the engine coolant temperature. Refer to
the engine manual for normal operating temperature. After
starting the engine, check your temperature gauge for
abnormally high readings. If the reading is outside the
manufacturer’s operating range, immediately turn OFF the
engine. An abnormally high temperature indicates a cooling
system problem. Consult your Nautique dealer when
experiencing a high engine temperature reading.
4 -6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 7
C o n t r o ls a n d In d ic a t o r s
• Oil Pressure - Measures the pressure of the engine’s
lubricating oil. Refer to the engine manual for normal
operating pressure. Many serious engine problems are
reflected on oil pressure gauge readings. If the pressure is
lower than the manufacturer’s specification, immediately
turn OFF the engine. Contact your Nautique dealer to
correct the problem before operating the engine.
• Tachometer / Hour Meter - Registers engine speed in
revolutions per minute (RPM). Use the tachometer to keep
the engine within the proper operating range. Consult the
engine manual for the proper RPM operating range of your
engine. The hour meter LCD display registers accumulated
engine operating time. Time will not be logged unless the
ignition switch is on and the engine is running. Use the hour
meter to keep accurate logs for scheduled maintenance.
• Speedometer - Your Nautique is equipped with a precision
speedometer by Faria. This gauge registers forward speed in
miles per hour (optional kilometers per hour). The
speedometer is equipped with an adjustment knob to
calibrate speedometer accuracy. You can also use this gauge
to monitor fuel consumption and propeller performance.
• Engine Warning Light - Indicates high engine temperature. If
light illuminates, stop engine and investigate for cause.
• Service Soon Light - For quality control check. When
ignition is turned on without cranking the engine, the red
“check engine” light will turn on for a few seconds and then
turn off. The amber “Service Soon” light will turn on and
stay on until either the engine is started or the ignition is
switched off. When the engine is running both lights will be
off. The amber “service soon” light will come on if there is a
problem with the catalyst system. The red “check engine”
light will come on for all other engine realted problems.
4 -7
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 8
S e c t io n 4
Speedometer Calibration
The speedometer calibration control knob is located on the under
side of the deck beneath the dash pod above the driver’s right knee.
Drive the boat at a known speed using a GPS or measured course
and adjust the knob until the speedometer is reading correctly.
Turning the knob one direction will raise the needle reading while
turning it in the other direction will lower the reading.
Control Switches
Each electrical circuit on your boat is equipped with a control
switch. The switches have an indicator light for easy ON/ OFF
identification. All switches are fuse protected.
Engine Compartment/ Bilge Area Blower
The “BLOWER” switch activates the engine compartment
ventilation blower to remove explosive fumes from the area. The
blower is turned on by pressing and releasing the “BLOWER”
switch. Press again to turn off. The blower must be operated for a
minimum of four minutes each time before starting the engines or
generator. In addition, the blower should be operated continuously
when at idle or running at slow speeds.
!
Explosion and fire hazard from gasoline
vapors can cause death or serious injury from failure to
check for fumes in the engine compartment or operating
the blower. Before engine start-up, check engine
compartment for gasoline vapors, then operate blower
for at least four minutes. Operate blower whenever
below planing speed.
4 -8
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 9
C o n t r o ls a n d In d ic a t o r s
Navigation Lights
The “NAV/ ANCHOR” switch controls the navigation lights. The
law requires the bow light and the 360 degree light (located near
the stern) be turned on while running the boat after sunset or
before dawn. NAV position will turn on the red and green
navigation bow lights, 360 degree white stern light and gauge
illumination.
!
Blocking navigation lights can cause
death or serious injury. DO NOT block the navigation
lights.
Anchor Light
The “NAV/ ANCHOR” switch turns on the 360 degree light. Insert
this light pole into the receptacle located near the stern and push
the anchor switch on the pod to turn this light on. This light is
required by law to be on after sunset and before dawn when the
boat is not moving.
Bilge Pump
The “BILGE” switch turns on the bilge pump to remove excess
water from the bottom of the boat. When you turn the switch on,
the pumps will operate and run for several moments to “sense” if
there is water in the bilge. If there is water in the bilge, the pumps
remain on until the water is pumped out. If there is no water in the
bilge, the pumps will turn off. If you want immediate pump action,
turn the switch off and then back on again. The pumps will turn on
periodically to determine if there is water in the bilge. If so, they will
remain on until the water is pumped out.
4 -9
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 10
S e c t io n 4
The bilge switch must be turned on for this feature to operate. This
will not drain significant power from the battery unless the bilge
pumps are required to run frequently because of a leak or excessive
rainwater. This pumping system should not be relied on over an
extended period of time. Frequently inspect your boat for evidence
of excessive water in the bilge area. Consult your Nautique dealer if
you have any questions.
NOTICE
Trash in bilge area can damage the bilge pumps.
Horn
The “HORN” button is a momentary switch. The horn will operate
whenever the button is pressed and will stop when the button is
released.
Engine Warning Light
This light indicates low engine oil pressure. The light should come
on when the ignition switch is in the ON position and the engine is
not running. If it stays on or comes on while you are operating the
boat, the light is indicating a problem. Turn the engine OFF. Refer
to the engine manual for additional information.
Heater Switch-Optional
The optional heater switch operates the fan to deliver heat. The
switch is a four position switch; OFF, LOW, MEDIUM and HIGH.
12-Volt Port
This receptacle can be used to power and charge cellular phones,
MP3 players, video cameras or other electronics. These receptacles
are powered through a 10-amp breaker.
4 -10
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 11
C o n t r o ls a n d In d ic a t o r s
Ignition Keyswitch
This keyswitch starts and stops the engine. A built-in protection
system prevents the engine from starting in any gear other than
NEUTRAL. Refer to Shifter/ Throttle in this section and consult
the engine operator’s manual for more information.
There is an accessory position on the ignition keyswitch and an
associated terminal on the back of the switch provided to control
power to add on accessories. Even though power to this terminal is
protected by a 20-amp fuse, do not connect any accessory that
draws more than 10 amps. Attaching an accessory to this terminal
should only be done by a qualified technician.
CAUTION
The keypad and switch control box will be
damaged beyond repair if the boat's battery cables, the
main switch control box power leads or battery charger
leads are reversed. DO NOT reverse these connections.
S m a r t P o d – L im it e d o r T e a m
Gauges
• Volts - Indicates the condition of the engine’s cranking
battery in volts DC. With the ignition switch on and the
engine not running, a reading above 12.5 volts indicates a
fully charged battery. With the engine running at idle, the
gauge should read between 12.5 and 13 volts. With the
engine running at cruising speeds and above, it should show
13 to 14.5 volts. Have your Nautique dealer check the
charging system if the voltmeter reads outside these normal
ranges.
• Temp - Indicates the engine coolant temperature. Refer to
the engine manual for normal operating temperature. After
starting the engine, check your temperature gauge for
abnormally high readings. If the reading is outside the
manufacturer’s operating range, immediately turn OFF the
engine. An abnormally high temperature indicates a cooling
system problem. Consult your Nautique dealer when
experiencing a high engine temperature reading.
4 -11
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 12
S e c t io n 4
• Oil Pressure - Measures the pressure of the engine’s
lubricating oil. Refer to the engine manual for normal
operating pressure. Many serious engine problems are
reflected on oil pressure gauge readings. If the pressure is
lower than the manufacturer’s specification, immediately
turn OFF the engine. Contact your Nautique dealer to
correct the problem before operating the engine.
• Tachometer/ Hour Meter - Registers engine speed in
revolutions per minute (RPM). Use the tachometer to keep
the engine within the proper operating range. Consult the
engine manual for the proper RPM operating range of your
engine. The hour meter LCD display registers accumulated
engine operating time. Time will not be logged unless the
ignition switch is on and the engine is running. Use the hour
meter to keep accurate logs for scheduled maintenance.
• Speedometer - Your Nautique is equipped with a precision
speedometer by Faria. This gauge registers forward speed in
miles per hour (optional kilometers per hour). The
speedometer is equipped with an adjustment knob to
calibrate speedometer accuracy. You can also use this gauge
to monitor fuel consumption and propeller performance.
• Engine Warning Light - Indicates high engine temperature. If
light illuminates, stop engine and investigate for cause.
• V-Drive Warning Light - Indicates low oil pressure in V-Drive.
If light illuminates when the engine is in gear and above
1200 rpm, stop engine and check V-Drive oil level.
Control Switches
Each electrical circuit on your boat is equipped with a control
switch. The switches have an indicator light for easy ON/ OFF
identification. All switches are protected by circuit breakers.
Belly, Port, Starboard Ballast
These buttons fill and drain the ballast tank designated to the
switch. Ballast tanks are an option on most Nautique boats. A full
description of how these buttons function is discussed in Section 4,
Ballast Tank Control Switches.
4 -12
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 13
C o n t r o ls a n d In d ic a t o r s
Underwater Lights
This switch controls the transom underwater lights. DO NOT
operate lights while the boat is out of the water.
Heater Fan (if equipped)
The heater button controls four different heater functions.
Pressing and releasing the “heater” button turns on Low Speed.
Press again for Medium Speed.
Press again for High Speed.
Press again for Off.
The indicator light for this button will illuminate if the heater is
running at any of the three speeds.
Courtesy/ Docking Lights
Press and release for courtesy lights, press and hold from this
position to turn docking lights on with courtesy lights. To turn the
courtesy lights and the docking lights off, press and release.
Docking lights only: from the OFF position, press and hold until
the docking lights are on and release, to turn off, press and release.
NOTICE
If either or both of the two light functions are on, the indicator
light will illuminate and a press and release will turn off any of
the lights that are on.
4 -13
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 14
S e c t io n 4
Engine Compartment/ Bilge Area Blower
The blower switch activates the engine compartment ventilation
blower to remove explosive fumes from the area. The blower is
turned on or off by pressing and releasing the button. The blower
must be operated for a minimum of four minutes each time before
starting the engines or generator. In addition, the blower should be
operated continuously when at idle or running at slow speeds.
!
Explosion and fire hazard from gasoline
vapors can cause death or serious injury from failure to
check for fumes in the engine compartment or operating
the blower. Before engine start-up, check engine
compartment for gasoline vapors, then operate blower
for at least four minutes. Operate blower whenever
below planing speed.
Navigation/ Anchor Light
A quick press and release of this button turns on the navigation
lights, and the indicator light for this button will illuminate. A press
and slight hold will only turn on the anchor light and cause the
indicator light to flash. A press and release of the key turns off both
of the lights.
!
Blocking navigation lights can cause
death or serious injury. DO NOT block the navigation
lights.
4 -14
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 15
C o n t r o ls a n d In d ic a t o r s
Bilge Pump
The bilge switch turns on the bilge pump to remove excess water
from the bottom of the boat. The pump turns on or off by pressing
and releasing the button. There is a bilge pump near the rudder
and one in the front. When you turn the switch on, the pump(s)
will operate and run for several moments to “sense” if there is water
in the bilge. If there is water in the bilge, the pump(s) remains on
until the water is pumped out. If there is no water in the bilge, the
pump(s) will turn off. If you want immediate pump action, turn the
switch off and then back on again. The pump(s) will turn on
periodically to determine if there is water in the bilge. If so, they will
remain on until the water is pumped out.
The bilge switch must be turned on for this feature to operate. This
will not drain significant power from the battery unless the bilge
pump(s) is required to run frequently because of a leak or excessive
rainwater. This pumping system should not be relied on over an
extended period of time. Frequently inspect your boat for evidence
of excessive water in the bilge area. Consult your Nautique dealer if
you have any questions.
NOTICE
Trash in bilge area can damage the bilge pumps.
Horn
The horn button is a momentary switch. The horn will operate
whenever the button is pressed and will stop when the button is
released.
4 -15
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 16
S e c t io n 4
12-Volt Port
This receptacle can be used to power and charge cellular phones,
MP3 players, video cameras or other electronics. These receptacles
are powered through a 10 amp breaker.
D a s h P o d - L im it e d o r T e a m
Ignition and Switch Panel
ST
AR
T
CORC137
NOTICE
Some of the switches on your boat may not have a function, based
on the way the boat is equipped.
Keyless Ignition
The optional ignition switch system is keyless and has three modes
of operation.
CAUTION
The keypad and switch control box will be
damaged beyond repair if the boatʼs battery cables, the
main switch control box power leads or battery charger
leads are reversed. DO NOT reverse these connections.
4 -16
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 17
C o n t r o ls a n d In d ic a t o r s
Locked Mode
When the boat’s battery is first connected, the unit is in locked
mode. In this mode, only the horn, bilge pump, bilge blower and
code keys operate.
Unlocked Mode
Unlocked mode is entered after the user successfully enters the
user code, presses and releases the start key. When the code keys
are pressed, the system indicator light will turn ON while the key is
pressed. This indicates the key has actually been pressed. When the
system is unlocked, power is supplied to the boat and the system
indicator light will turn ON. At this point all keypad keys will
operate and actuating these keys will control the corresponding
boat functions. To put the unit back in Locked Mode, the user must
successfully enter the user code, then press the STOP key. This will
turn off the system indicator light and shut off power to all of the
accessories except the horn, bilge pump, bilge blower and code
keys.
Run Mode
Enter the Unlocked Mode.
Pressing and releasing the START key quickly will put the unit in
Run Mode. Power is supplied to the engine ignition, but the engine
will not crank and the ignition indicator light is turned ON. If the
start key is not pressed again within 15 minutes, the unit will exit
Run Mode by shutting off power to the ignition and re-enter the
Unlocked Mode. If the user presses and holds the START key,
power is supplied to the ignition and starter for as long as the user
presses the START key. All accessory keys will operate in this mode.
Pressing the STOP key will shut off the engine and the unit is then
put back in the Unlocked Mode.
After the engine starts, release the START key.
CAUTION
DO NOT hold the START key for more than 30
seconds. The starter motor can be damaged.
4 -17
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 18
S e c t io n 4
Automatic Return to Locked Mode
If no keypad activity takes place for 10 hours after unlocking, the
system will automatically return to the Locked Mode to help
prevent battery drain.
Automatic Back-lighting
Pressing any keypad key will automatically turn the keypad back-
lighting on for 10 seconds. This feature is useful for finding the
keypad at night.
Multiple Keyless Ignition Codes
The keyless ignition system has provisions for three different
ignition codes. Any of the three codes may be used to unlock or
lock the system.
The “Master Embedded Code” is programmed into the system at
Correct Craft, Inc. It is not changeable and remains with the boat
for its life. This code can be used to unlock the system, to lock the
system and to erase the two user codes.
The “Primary User Code” is programmed into the system by the
owner with the Nautique dealer’s help at the time of boat delivery.
This code is used to unlock the system, to lock the system and to
add or change the “Secondary User Code.”
The “Secondary User Code” is programmed into the system by the
owner when necessary. This code is only used to unlock or lock the
system. The “Secondary User Code” is ideal to limit access to the
boat.
NOTICE
To help prevent battery drain, make sure you STOP the engine
and LOCK the PME ignition system (two steps) when you are
finished using the boat.
4 -18
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 19
C o n t r o ls a n d In d ic a t o r s
NOTICE
The “System Indicator Light” is on the right side of the ignition
keypad. The “Ignition Indicator Light” is on the left side of the
ignition keypad.
Programming the Primary User Code
NOTICE
Until a Primary User Code is set, the keyless ignition does not
require the entry of a code to unlock the system or start the engine.
This system operates as follows:
1. Press START to unlock the system.
2. Press it a second time to start the engine.
3. Press STOP to turn off the engine.
4. Press it a second time to lock the system. The system indicator
light should be OFF.
To program the Primary User Code, make sure the system indicator
light is off, then press and release the 1/ 2 key and the 7/ 8 key at
the same time to put the system in the Code Programming Mode.
The system indicator light will flash.
Enter a code from two to eight characters and press START. For
verification, re-enter the code and press START again. The system
indicator light should stop flashing and stay ON. If the light does
not stop flashing, press STOP and begin again.
To lock the system, re-enter either the Primary User Code or the
Master Embedded Code and press STOP.
4 -19
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 20
S e c t io n 4
Changing the Primary User Code
NOTICE
The current primary code must be used to change to another
primary code.
Make sure the system indicator light is OFF.
1. Enter the Primary User Code, then press and release the 1/ 2
key and the 7/ 8 key at the same time to put the system in the
code programming mode. The system indicator light will flash.
2. Enter a code from two to eight characters and press START. For
verification, re-enter the code and press START again. The
system indicator light should stop flashing and stay ON. If the
light does not stop flashing, press STOP and begin again.
To lock the system, re-enter either the new Primary User Code or
the Master Embedded Code and press STOP.
NOTICE
Changing the Primary User Code will erase the Secondary User
Code.
Programming or Changing the Secondary User Code
NOTICE
The Secondary User Code will only lock or unlock the system and
can not be used for any reprogramming
Make sure the system indicator light is OFF.
1. Enter the Primary User Code, press and release the 1/ 2 key and
the 5/ 6 key at the same time to put the system in Code
Programming Mode. The system indicator light will flash.
2. Enter a code from two to eight characters and press START. For
verification, re-enter the code and press START again. The
system indicator light should stop flashing and stay ON. If the
light does not stop flashing, press STOP and begin again.
To lock the system, re-enter any of the three codes and press STOP.
4 -2 0
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 21
C o n t r o ls a n d In d ic a t o r s
Erasing the User Codes
Make sure the system indicator light is OFF.
Enter the Master Embedded Code, press and release the 1/ 2 key
and the 7/ 8 key at the same time to erase the system user codes.
The keyless ignition will now act as if there are no codes in memory.
Pressing the START key will unlock the system and pressing the
STOP key will lock it without entering a code. Follow the steps in
“Programming The Primary User Code” in this section.
Nautique Cruise Control
CORC219
The steering wheel hub cruise control remote has five control
buttons:
(ON/ OFF)
SET
CNCL (Cancel)
s / RES (increment UP/ Resume)
t (decrement DOWN)
4 -2 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 22
S e c t io n 4
There are three small lights in the dash display that indicate the
status of Nautique Cruise. The top light is labeled MPH, the middle
one labeled RPM, and the bottom one labeled SET. When
Nautique Cruise is on either the MPH or RPM light will be
illuminated and the SET light will either be off, flashing slowly, or
on continuously. When the SET light is off, Nautique Cruise will not
control speed and the throttle control will function normally at all
speeds. If the SET light is flashing Nautique Cruise is armed but the
boat speed is below the set point. The throttle control will function
normally as long as the boat speed is below the set point. When the
speed nears the set point, Nautique Cruise will take over
controlling the speed. When Nautique Cruise takes over the SET
light illuminates continuously.
NOTICE
After Nautique Cruise takes control, it is best to push the throttle
control handle down a good portion of the way toward full throttle
in order for Nautique Cruise to function correctly. Nautique
Cruise can be turned off by pulling the throttle back toward
neutral, by pushing the Cancel button or by turning Nautique
Cruise off.
When the ignition is turned OFF and back ON, Nautique Cruise
will “remember” the last set point and return to it. The indicator
lights will provide the operator with an indication of the Nautique
Cruise status.
There are two ways to operate the buttons on the steering wheel
hub. One is to “push and release” (push and after a short delay of
more than 1/ 2 second but less than two seconds, release the
button). The other is to “push and hold” (push and after a longer
delay of at least two seconds, release the button).
4 -2 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 23
C o n t r o ls a n d In d ic a t o r s
Button Function
The MPH/ RPM button turns Nautique Cruise ON and OFF.
• When Nautique Cruise is OFF, a push and release of the
button will turn Nautique Cruise on in “SPEED MODE,”
while a push and hold will turn Nautique Cruise on in “RPM
MODE.” Turning Nautique Cruise on in either mode will
illuminate the appropriate light on the dash display.
• When Nautique Cruise is ON, a push and release or a push
and hold of the button will turn Nautique Cruise OFF, also
turning off the dash indicator light.
The SET and CNCL buttons respond the same way to a “push and
release” or a “push and hold.”
• If the SET light is off or flashing, the SET button activates
Nautique Cruise at the current boat speed, causing the SET
light to illuminate continuously while controlling the boat
speed.
• If the SET light is on continuously, the SET button will have
no effect.
• If the SET light is on continuously or flashing the CNCL
button will turn the SET light off and allow the boat to be
driven with the hand throttle.
• If the SET light is off the Set button will have no effect.
The s (increment) and t (decrement) buttons respond the same
way to a “push and release” or a “push and hold” and will only
function if the SET light is on continuously.
• The s (increment) button will raise the set speed
approximately 1/ 4 mile per hour.
• The t (decrement) button will decrease the set speed
approximately 1/ 4 mile per hour.
4 -2 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 24
S e c t io n 4
Gauges
The optional dash pod uses the Faria® Serial BusTM system which
receives information from the engine ECU and various individual
sensors throughout the boat. This information is transformed into
digital data, which is distributed to analog and digital instruments
via a single cable consisting of two shielded, twisted pairs of
conductors.
Each instrument selects the data, which applies and displays it as if
it was received from the sender directly. One of the two pairs of
conductors carries the data while the other pair of conductors
carries the power for the instruments. The tachometer and
speedometer each have three pushbuttons, which allow the
different functions of each instrument to be activated.
Mode
Button
M
Down
Button
Up
Button
CORC113
4 -2 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 25
C o n t r o ls a n d In d ic a t o r s
Refer to Standard Dash Pod in this section for additional
information on gauge operation.
Speedometer/ Depth Sounder
The Serial Bus Speedometer/ Depth Sounder provides both the
functions of a speedometer and a depth sounder. The analog
speedometer looks like a standard analog device but is actually a
digital instrument. On small pointer movements you may
occasionally see the pointer moving in the one-third degree "steps"
that represent the accuracy of the instrument.
QUICK
PRESS
PILOT STATUS
AIR TEMPERATURE
(OPTIONAL)
M
M
ADJUST
M
QUICK
PRESS
SAVE
WATER TEMPERATURE
(OPTIONAL)
M
NO SAVE
QUICK
PRESS
DEPTH SOUNDER
M
SHALLOW
ALARM SET
M
DEEP
ALARM SET
KEEL
OFFSET
SELECT
UNITS
CORC114
4 -2 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 26
S e c t io n 4
Speedometer Function
The speedometer measures speed over the water using a paddle
wheel sensor.
Speedometer Calibration
The analog speedometer displays the speed of the boat through the
water. The speedometer is calibrated at the factory however,
significant variations can occur due to changes in installations. The
speedometer can be easily calibrated to a known reference such as
a radar gun, measured course, or GPS.
When the unit is in digital speed display mode, push and release M
to put the speedometer in the calibration mode. Push and hold M
down for at least two seconds, the LCD will show “AdJUST.”
Calibration Display
CORC117
Run the boat at a constant 30 MPH as measured by the GPS, radar,
or closed course. Adjust the speedometer pointer by pressing s
and t until the speedometer matches the known speed.
When finished, press M to exit the adjustment screen. The operator
has the option of saving or canceling the adjustment procedure.
The options can be selected using s and t . To save the calibration
setting, press and hold M for two seconds when the display shows
“SAVE.”
Save Display
CORC118
4 -2 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 27
C o n t r o ls a n d In d ic a t o r s
To exit the adjustment procedure without saving, press and hold M
for two seconds when the display shows “NO SAVE.” Multiple runs
in opposite directions may be necessary to compensate for errors
due to water currents.
No Save Display
CORC119
Depth Sounder Function
To display depth information on the LCD push and release the M
until the display shows the depth. The depth sounder is turned on
and off with the ignition switch. The depth sounder can also be
turned off at any time, while in depth display mode, by pressing and
holding M while the depth sounder counts down a three second
delay.
The depth display will then indicate “OFF.”
Off Display
CORC120
Press and hold the M to turn the depth sounder back on.
When there are no alarm conditions, the water depth is displayed.
If the signal is weak or lost, or there is no transducer connected, the
display will alternate between the last known depth and four
horizontal bars.
4 -2 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 28
S e c t io n 4
Depth Display
CORC121
Canceling Depth Alarms
A depth alarm warning can be temporarily canceled by pressing
both s and t on the speedometer, simultaneously. After one
minute, the alarm will resume if the condition that caused the
alarm is not corrected. The operator can cancel the alarm as many
times as necessary, until the condition is corrected.
The depth alarm warning will replace any information on the LCD
screen. Canceling the alarm will restore the LCD to the original
display. If not already in the depth mode, this would be a good time
to switch to it (using M) in order to monitor water depth.
Depth Sounder Alarm Settings
NOTICE
The speedometer display must be in the depth display mode to
change settings. Use the M to scroll to the depth display.
To change the depth sounder alarm settings M must be held down
until the depth display changes to the alarm settings mode.
There are four menus in the alarm settings mode. Pressing and
releasing the mode switch quickly will cycle through the different
options.
Shallow Alarm
This alarm sounds when the water depth equals or is less than the
set value.
The display will show “S X.X” which is the current setting for the
shallow alarm. Pressing s and t will change the shallow setting.
4 -2 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 29
C o n t r o ls a n d In d ic a t o r s
Shallow Display
CORC122
Holding M in for two seconds will save the new shallow setting and
change the display back to the normal depth mode. Set to zero to
disable the alarm.
Deep Alarm
This alarm sounds when the water depth equals or is greater than
the set value.
The display will show “d XX.X” which is the current setting for the
deep alarm.
Deep Display
CORC123
Pressing s and t will change the deep setting.
Holding M in for two seconds will save the new deep setting and
change the display back to the normal depth mode. Set to zero to
disable alarm.
Keel Offset
Adjust depth sounder to measure depth below keel or drive instead
of sensor.
The display will show “K X.X” which is the current setting for the
keel offset. Pressing s and t will change the keel-offset setting.
4 -2 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 30
S e c t io n 4
Keel Display
CORC124
Holding M in for two seconds will save the new keel offset setting
and change the display back to the normal depth mode. The keel
offset is normally a negative number.
Units
Change the unit of measure.
This display will show “UNIT FT” for feet (default), “UNIT FA” for
fathoms, or “UNIT M” for meters. Pressing s and t will cycle
through the choices. Pressing and holding the M will save the units
shown in the display and change the display back to the normal
depth mode.
4 -30
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 31
C o n t r o ls a n d In d ic a t o r s
Feet (default)
METERS
FATHOMS
CORC125
Tachometer/Fuel Monitor
The Tachometer/ Fuel Monitor provides both the functions of a
tachometer and a fuel – engine monitoring system. The analog
tachometer looks like a standard analog device but is actually a
digital instrument. On smaller pointer movements you may
occasionally see the pointer moving in the one-third degree “steps”
that represent the accuracy of the instrument.
The tachometer LCD screen displays several user selected
functions. The displayed data includes: “engine hours,” “time
remaining,” “engine temperature,” “oil pressure,” “system voltage”
and engine alarm conditions.
Pressing the “mode M” button will select the various functions as
shown in the Tachometer Display Sequence.
In order to minimize “false” alarms, the “low fuel” and “low voltage”
alarms only function when the engine is known to be running
based on the presence of tachometer data.
4 -31
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 32
S e c t io n 4
Engine Hour Meter
Displays the number of hours the engine has been operated. The
display will show “XXXX.XHr.” Engine hours only accumulate
when the engine is running.
Hourmeter Display
CORC126
Hours Remaining
The “time remaining” display shows the approximate number of
hours the boat can operate based on the fuel remaining in the tank
and the current fuel usage rate. The display will show
“XXXX.XHrL.”
Hours Remaining Display
CORC127
Engine Temperature
Displays the Coolant Temperature of the Engine. There are no
adjustments available.
CORC205
4 -32
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 33
C o n t r o ls a n d In d ic a t o r s
Voltmeter
Displays the System Voltage. There are no adjustments available.
Voltmeter Display
CORC129
Oil Pressure
Displays the current Oil Pressure. There are no adjustments
available.
Oil Pressure Display
CORC130
Instrument Lights
The navigation light switch must be on for the instrument lights to
function. The s and t on the tachometer control the instrument
lighting intensity.
Press s to increase the light intensity. Press t to decrease the light
intensity.
4 -33
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 34
S e c t io n 4
Tachometer Display Sequence
QUICK
PRESS
HOURMETER
VOLTMETER
M
M
QUICK
PRESS
QUICK
PRESS
HOURS REMAINING
OIL PRESSURE
M
M
QUICK
PRESS
ENGINE TEMPERATURE
M
CORC131
LCD Alarm Condition Displays
Alarm messages will be displayed on the Tachometer LCD display.
All messages will be displayed until either the problem is corrected
or the operator manually cancels the warning message.
Messages will display as many screens shown sequentially.
Canceling System Alarms
To manually cancel system warning messages, simultaneously press
both s and t on the tachometer. This will disable the warning
message temporarily. If the problem is not corrected in one minute
(five minutes for low fuel), the warning will be displayed again. The
operator can cancel as often as needed.
4 -34
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 35
C o n t r o ls a n d In d ic a t o r s
Severe Conditions – Includes a Flashing Red Light
WARNINGS
Low Battery Voltage (Flashing Red Light)
High Engine Temperature (Flashing Red Light)
Low Oil Pressure (Flashing Red Light)
Low Fuel Level (Flashing Red Light)
RPM Reduction in Progress (Flashing Red Light)
CORC132
Engine Speed Limiter Active
Knock Detection System Malfunction
Spark Delivery System Malfunction
Manifold Pressure System Malfunction
Manifold Air Temperature Sensor Malfunction
Throttle Position Sensor Malfunction
Coolant Temperature Sensor Malfunction
CORC134
4 -35
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 36
S e c t io n 4
Dash Pod Circuit Breaker Box
All dash pod switches interface with a sealed circuit breaker box
located in the driver’s kickboard. The circuit breaker box consists
of 16 soft, opaque, flexible vinyl tubular shields which cover 16
circuit breakers. When the circuits are functioning, the tubular
shield is somewhat flexible. A tripped circuit breaker will extend
and fill the tubular shield, causing it to be inflexible. To locate a
tripped circuit breaker, run your fingers over the two rows of
switches and locate the switch shield which has become inflexible.
To re-set, press in the extended circuit switch shield.
NEGATIVE
COURTESY
/DOCKING
LIGHTS
KEYPAD
POWER
HEATER
MED/HIGH
HEATER
LOW
NAV/
ANCHOR
LIGHTS
HORN
BLOWER
BILGE
U
T
I
O
N
C
A
LCS PORT
FILL/
DRAIN
STARTER/
RUN
LCS STBD
FILL
LCS BELLY LCS BELLY
LCS STBD
DRAIN
UNDERWATER
LIGHTS
UNLOCK
DRAIN
FILL
POSITIVE
CORC035
4 -36
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 37
C o n t r o ls a n d In d ic a t o r s
S t a n d a r d E q u ip m e n t
Watersports Tow Point
The watersports tow-point (pylon) is manufactured from high
strength aluminum alloy, engineered for durability. It is “hard coat
anodized” and impregnated with a PTFE (teflon) material. If the
pylon becomes loose, stop using the pylon and take the boat to your
Nautique dealer for service.
!
Misuse of the tow-point can cause death
or serious injury. The pylon was designed for water
skiing only. DO NOT use for parasailing, kite flying,
towing other boats and / or using pylon extensions, sit
behind (aft) the pylon when towing skiers.
CAUTION
Although pylon extensions and barefoot
booms have become popular additions to many
tournament inboards, Correct Craft strongly objects and
opposes the use of any pylon extension, whether up or
to the side of any of its products. The use of pylon
extensions can alter the handling characteristics of the
boat, possibly resulting in dangerous instability, which
could then lead to loss of control, a situation which
could cause serious or fatal injury to the boat driver,
passengers, skiers and anyone else who might be in the
vicinity of such a mishap.
4 -37
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 38
S e c t io n 4
CAUTION
Correct Craft DOES NOT approve of any
structural changes, additions or modifications to our
products. Any time a dealer or consumer makes a
change to our product, they do so at their own risk and
sole liability. Correct Craft, Inc. will not be held liable for
unauthorized changes, whether deletions or additions,
to the original equipment / product manufactured and
sold by Correct Craft, Inc., even if such changes and
additions are made by an "authorized" Correct Craft
Dealer, customer, promotional representative or any
other person, known or unknown to Correct Craft, Inc.
Bow Features of Your Nautique
The open bow section of your boat has removable cushions. The
center section may be equipped with an optional cushion which
can be removed and stored in the trunk or under the love seat. The
cushion on the starboard side of the bow section of the 226 can be
removed to access the insulated cooler. Storage can be accessed by
removing the other cushions.
4 -38
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 39
C o n t r o ls a n d In d ic a t o r s
Driverʼs Seat Adjustment
The driver’s seat can be adjusted fore and aft and rotates side-to-
side.
To slide seat, turn the handle (A) counterclockwise about one full
turn, slide into position, and tighten the handle hand-tight to
secure in locked position.
To rotate seat, pull up on the lever (B) at the front of the seat and
push to the side. Release lever to lock the seat in position.
!
A seat or seats which are not locked in
position can cause death or serious injury. Lock the
seat(s) in position (fore and aft) before operating the
boat.
B
CORC164
A
4 -39
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 40
S e c t io n 4
Rearview Mirror Adjustment
The rearview mirror can be positioned on the windshield to
observe a skier and traffic behind you. The mirror should be
lowered when trailering or when using a mooring cover. To
reposition, loosen the thumbscrews (A), reposition and tighten
thumb screws.
Use the mirror friction nut (B) to increase the friction of the mirror
adjustment. If the mirror moves out of adjustment, increase the
friction by turning the friction nut clockwise.
B
A
CORC165
4 -4 0
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 41
C o n t r o ls a n d In d ic a t o r s
Love Seat
Lift up on the bottom of the love seat cushion to access storage
under the bow area. You can leave the seat in the “UP” position to
help dry the carpet.
Storage Hatch
To open the storage hatch, lift the latch and turn counterclockwise.
The gas shock will help raise the hatch. To close and latch the
hatch, pull down on the hatch and allow the hatch to close firmly.
Make sure there are no hands, fingers or any other obstructions in
the way of the hatch when you close it. To close the latch, turn the
latch clockwise and fold the red dot down.
The storage hatch latch features a lock. Use the key to lock and
unlock the latch. The key only requires about a 10° turn to lock and
unlock.
CORC146
4 -4 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 42
S e c t io n 4
Engine Cover Hatch
To open the engine cover hatch, lift the latch and turn
counterclockwise. The gas shock will help raise the hatch. To close
and latch the hatch, pull down on the hatch and allow the hatch to
close firmly. Make sure there are no hands, fingers or any other
obstructions in the way of the hatch when you close it. To close the
latch, turn the latch clockwise and fold the red dot down.
The engine cover hatch latch features a lock. Use the key to lock
and unlock the latch. The key only requires about a 10° turn to lock
and unlock.
COR036
210, 211, 220
!
An engine guard which is not in place or
contact with any moving parts can cause death or
serious injury. The engine box cover is a machinery
guard. DO NOT operate your boat without the cover
closed and in place unless you are performing a check
or maintenance. Keep your hands, clothing, hair and
any other body parts away from any moving parts.
4 -4 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 43
C o n t r o ls a n d In d ic a t o r s
Walk-Thru Windshield Opening/Latching
There are two latches on the inside starboard side of the walk-thru
windshield. Rotate both of the window locks (A) to secure or
unlock the window. Always have window closed and secured when
trailering the boat.
A
A
CORC039A
!
An open window can cause death or
serious injury. Make sure both window locks are secure
when vessel is in motion.
Coolers
The floor coolers can be used to store miscellaneous items or
drinks. There is a drain installed in the coolers. DO NOT depend
on the coolers to keep valuables or electronics dry. Keep these
items in a specialized dry bag. The floor cooler has a removable
tray. DO NOT use abrasive cleaners or place in a dishwasher. Use a
mild biodegradable soap only.
4 -4 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 44
S e c t io n 4
Boarding Platform
The boarding platform of your boat is a convenient feature to
enhance the watersports experience. There are serious safety
concerns regarding the use of the platform. Correct Craft, Inc. has
placed warning labels at the driver’s position, on the deck at the
rear of the occupant area and on the transom. Refer to Section 1,
Safety, for more information.
To remove the boarding platform, pull the pins (A) located in the
mounting brackets, under the platform and lift the platform
vertically.
A
CORC025
!
A spinning propeller or carbon monoxide
can cause death or serious injury. DO NOT use the
boarding platform when the engine is running or for any
other purpose than boarding the boat or preparation for
entering the water.
The boarding platform must be attached when the boat is in use.
4 -4 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 45
C o n t r o ls a n d In d ic a t o r s
Engine Cooling Water Intake Valve
Your boat is equipped with a valve (seacock) on the engine cooling
water intake. The handle has a slide mechanism to prevent the
valve from being shut off inadvertently. The valve is used to shut off
the water supply in the event a hose failure or water leakage occurs.
The valve is open when the yellow handle is in-line with the valve
body and the valve is closed when the handle is perpendicular to
the valve body. Leave the valve open at all times unless an
emergency condition requires you to close the valve to stop a leak
or the possibility of a leak.
The valve is located on the starboard side of the transmission.
WATER
VALVE
CORC106
4 -4 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 46
S e c t io n 4
Fuel Tank
There is a fuel tank fill cap on the port and starboard side for added
convenience. Use the fuel tank fill cap key to remove the fuel fill
cap to fuel your boat. Use caution when fueling your boat.
Avoid overfilling of the tank by monitoring the fuel level gauge
while fueling. Turn on the ignition without starting the engine and
monitor the gauge. Stop fueling as the gauge approaches the ‘full’
level and turn off the ignition when finished. Fuel spillage on our
waterways will pollute our environment.
The fuel tank is located beneath the cockpit deck, in the center of
the boat. To inspect the hose connections, raise the access panel.
Your Nautiques dealer should perform all fuel tank service.
!
Explosion or fire can occur under certain
conditions, causing death or serious injury:
• Turn the engine OFF.
• DO NOT smoke or allow open flame or sparks within
50 feet (15 meters) of the refueling area.
• DO NOT refuel unattended, avoid contact and spilling.
• DO NOT refuel indoors.
• DO NOT use a plastic funnel.
• DO NOT allow any spilled fuel to remain on your boatʼs
finish.
• DO NOT allow a fuel system problem to go unchecked.
• Always maintain contact with the fuel nozzle and the
fuel tank to prevent electrostatic spark.
4 -4 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:54 PM Page 47
C o n t r o ls a n d In d ic a t o r s
Battery Selector Switch
The battery selector switch allows you to isolate the boat from the
batteries, and switch from one battery to the other, or even operate
on both batteries. The identification of each battery as well as the
position allowing both to be used may differ depending on the
switch manufacturer, however, with any switch it should be easy to
determine how to select the desired configuration.
Under normal conditions, the switch should be set to one battery
or the other and almost never to the position for both batteries.
This will keep one battery in reserve should the other fail. Battery
selection should be done when the engine is off. Alternate batteries
daily. The switch can also be set to a position that turns off both
batteries isolating the boat from the batteries.
!
Avoid the possibility of personal injury or
death from an explosion and/or fire. Never operate the
boat with only one battery installed and the Battery
Selector Switch set to the position for both batteries.
The positive battery cable end of the missing battery will
be at full battery voltage and could short out against
metal components possibly causing an explosion
4 -4 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:55 PM Page 48
S e c t io n 4
Automatic Bilge Panel
Bilge Pump Only Mode - This feature is activated by a switch located
on the side console. The switch has three positions, ON, OFF and
BILGE. If the boat is going to sit for more than a few days with the
bilge pumps on, it is important the switch is set in the BILGE
position to minimize battery drain. This will activate the bilge pump
and shut off power to the Serial Switching and Keyless Ignition
System. It is important to remember the engine or other accessories
can not be used unless the switch is in the ON position.
All On
Bilge
Pump
Bilge
Pump
Indicator
All Off
Circuit
Breaker
Bilge Pump On
CORC024
CORC202
An indicator light is located with the switch for the bilge pump. The
indicator light will come on anytime the bilge pump is activated. If
your panel has a circuit breaker, the circuit breaker is only active
when the switch is in the BILGE position.
4 -4 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:55 PM Page 49
C o n t r o ls a n d In d ic a t o r s
Folding Instructions for Flight Control Tower® – Optional
!
Crush hazard. The Flight Control Tower is
heavy. Use care to fold or unfold the tower.
Flight Control Tower® Series 1 (FCT 1)
The Flight Control Tower® Series 1 (FCT 1) folds forward. To fold
the tower, loosen the knobs found under the support structure on
the port and starboard sides of the tower. Fold down light before
folding tower. Fold the tower forward. The tower will rest on the
bow section of the boat. In the folded position, strap securely to the
grab rails. Reverse the steps to return the tower to the upright
position. Make sure to tighten knobs securely before using the
tower.
CORC0221
4 -4 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:55 PM Page 50
S e c t io n 4
Flight Control Tower® Series 2 (FCT 2)
The Flight Control Tower® Series 2 (FCT 2) folds aft. To fold the
tower, loosen the knobs, under the top crossbar. Grasp both the
forward crossbar and the aft crossbar. Then lower the tower into the
cockpit seating area. Make sure the black protective sleeves are
positioned so they protect the tower and windshield header frame
when it rests on the windshield frame. The aft crossbar will rest on
the stern seat. Place a towel or something similar on the seat to
protect it. Reverse the steps to return the tower to the upright
position. Make sure to tighten the knobs securely before using the
tower.
CORC0218
4 -5 0
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:55 PM Page 51
C o n t r o ls a n d In d ic a t o r s
210, 220, 230 and 236 - Flight Control Tower® Series 3
(FCT 3)
Remove all boards from the board racks prior to folding the tower.
Make sure to support the tower before unlocking the tower lock
handles.
To Lower
Support the tower. Push the lock handles (A) down and rotate fully,
until they stop. Gently lower the tower ensuring it does not make
contact with anybody or part of the boat.
To Raise
Make sure the handles are in the fully open position before raising
the tower. Slowly raise the tower into position making sure nothing
interferes with a smooth seating.
With the tower in the fully upright position, turn the lock handles
(A) upward until they stop. The handles will be horizontal when
locked properly.
A
CORC0222
NOTICE
DO NOT leave the tower speakers facing forward while the boat is
underway or trailered. Make sure they are facing aft and secured.
4 -5 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:55 PM Page 52
S e c t io n 4
If your tower is equipped with the optional tower speakers, they can
be adjusted for redirection of sound by loosening the speaker
mounting hardware and adjusted. Make sure the hardware is
securely tightened after it is loosened.
Flight Clips™
One set (four) Flight Clips™ will hold a maximum of four
wakeboards. DO NOT overload Flight Clips™ with more than one
piece of equipment per slot. When loading boards into the Flight
Clips™, always insert boards into individual slots so the board
bottoms are facing each other. Always visually inspect bungee to
ensure the locking ball is securely in the locking claw.
CORC153
!
Flying objects can cause death or serious
injury. DO NOT trailer your boat or attempt to fold tower
with any items in the board racks
4 -5 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:55 PM Page 53
C o n t r o ls a n d In d ic a t o r s
Ballast Tanks
The tanks increase the wake for wake boarding, making your
Nautique the most versatile watersports tow package in the world.
Ballast Tank Control Switches
Press the button for the ballast tank you choose to fill or drain.
To fill: Press and release quickly; the LED will illuminate and the
pump will begin to fill the tank. Press the button again to stop the
pump. Use the tank gauge to measure the level of water in the tank.
If you continue to fill the tank beyond its capacity, the excess water
will expel from the tank vent. The pump will continue to operate
for approximately 10 minutes if the pump is left in the fill mode,
then shut off.
To drain: Press and hold the button until the LED begins to flash
and the pump will begin to drain the tank. Press the button again
to stop the pump.
The pump will stop pumping when the tank sensor senses the “No
Water Level” in the tank. The LED will continue to flash for
approximately 10 minutes unless the button is pressed again.
4 -5 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:55 PM Page 54
S e c t io n 4
1/2
E
F
WA
TER
1/2
E
F
W
ATER
1/2
E
F
WA
TER
CORC140A
Ballast Control Switches - 211, 220
CORC208A
Ballast Control Switches - 210, 230 and 236
4 -5 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:55 PM Page 55
C o n t r o ls a n d In d ic a t o r s
O p t io n a l A c c e s s o r ie s
Stereo and Speaker Pods
All Nautique boats are stereo ready and include an Auxiliary Input.
They have been pre-wired for your Nautique dealer to install a
stereo. Limited and Team Edition Nautique boats come with a
Clarion stereo with Polk/ MM speakers. Tower speakers can be
purchased as an option. Nautiques by Correct Craft mounts all of
its stereos in the glove box on the dash. A digital remote control can
be mounted on the lower left side of the dash pod. The digital
remote control displays all necessary control functions at your
fingertip. Consult your Nautique dealer for the stereo
configuration for your boat.
Optional accessories are available from your Nautique dealer. Your
dealer may have a wide range of other accessories available to
enhance your watersports or pleasure boating experience. Contact
your Nautique dealer for more information. Here are just a few of
the fine accessories Nautiques by Correct Craft offers:
• Pull-out Cleats
CORC042
4 -5 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 4_2008.qxd:Naut Air Sec 4.qxd 6/24/08 3:55 PM Page 56
S e c t io n 4
• Sun Pad Cargo Net - 210, 220 Only
CORC179
• Sun Pad Cargo Net - 211 Only
CORC217
4 -5 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 5_2008.qxd:Naut Air Sec 5.qxd 6/24/08 3:55 PM Page 5-1
S e c t io n 5
B o a t S y s t e m s
Knowing the systems, controls and indicators on your boat is
essential for safe and proper operation.
!
Systems which are not inspected
regularly or maintained can cause death, serious injury
or damage to product. Inspect and maintain all systems
to prevent unexpected hazards associated with worn or
faulty components.
When replacement parts are required, use marine grade parts with
equivalent characteristics, including type, strength and material.
Marine grade parts are designed specifically for the conditions and
environment they are exposed to. Using substandard parts could
result in injury and product failure.
F u e l S y s t e m
The fuel system consists of a built-in fuel tank, a port fuel fill, a
starboard fuel fill and a fuel tank vent.
The fuel tank is located under the cockpit floor. To inspect, lift aft
seat base and removable section of the cockpit floor.
5 -1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 5_2008.qxd:Naut Air Sec 5.qxd 6/24/08 3:55 PM Page 5-2
S e c t io n 5
FUEL
TANK
FUEL TANK
VENT
FUEL
FILL
FUEL
FILL
ENGINE
CORC097
5 -2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 5_2008.qxd:Naut Air Sec 5.qxd 6/24/08 3:55 PM Page 5-3
B o a t S y s t e m s
B a lla s t T a n k s a n d B ilg e
S y s t e m
NOTICE
The Federal Water Pollution Control Act prohibits the discharge of
oil or oily waste into the water. Violators can be fined $5,000.00.
Do not allow water to accumulate in the bilge area of your
boat. When the boat is in use, make sure the bilge pump is
turned on. The bilge pump is an automatic pump that tests
for the presence of water every two to three minutes and
pumps until the water is removed. If the pump is in
between detection cycles, the detection mode can be
bypassed to operate immediately by turning the switch off
and then back on. Remember, the engine and other parts
of the drive system could be damaged and there is also a
risk of personal injury as increasing water level will
adversely affect the handling and maneuverability of the
boat.
CAUTION
The risk of personal injury from excess water
in the bilge area will adversely affect the handling and
maneuverability of the boat. Also, damage to the engine
and other parts of the drive system can occur from the
additional water. DO NOT allow the bilge pump to
operate after all the water has been cleared from the
bilge area, damage to the pump will occur.
5 -3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 5_2008.qxd:Naut Air Sec 5.qxd 6/24/08 3:55 PM Page 5-4
S e c t io n 5
BILGE DRAIN
BELLY
VENT
BALLAST
TANK
PORT BALLAST
STARBOARD BALLAST
TANK WATER
INTAKE/DRAIN VALVE
BILGE
TANK WATER
INTAKE/DRAIN VALVE
BELLY TANK WATER
INTAKE/DRAIN VALVE
PORT BALLAST
TANK PUMP
STARBOARD BALLAST
TANK PUMP
PORT BALLAST
TANK
STARBOARD
BALLAST TANK
BILGE DRAIN
VENT
BILGE
VENT
ENGINE
BELLY
TANK PUMP
CORC104
5 -4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 5_2008.qxd:Naut Air Sec 5.qxd 6/24/08 3:55 PM Page 5-5
B o a t S y s t e m s
H e a t e r S y s t e m - O p t io n a l
HEATER
ENGINE
CORC099
5 -5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 5_2008.qxd:Naut Air Sec 5.qxd 6/24/08 3:55 PM Page 5-6
S e c t io n 5
N O T E S
5 -6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-1
S e c t io n 6
G e t t in g U n d e r w a y
There are many things to consider to make your boating trip safe
and enjoyable. You are responsible for the safety of all passengers,
the boat and any damage the boat or its wake may cause. Keep
passengers from blocking your view so that you do not run into
other boats, swimmers, water skiers, personal water vehicles or aids
to navigation.
S a f e t y C h e c k lis t
!
Operating the boat if any problem is found
during this inspection can cause death or serious injury.
DO NOT operate the boat if any problem is found during
this inspection.
Problems found during this inspection should be handled by your
Nautique dealer.
The following checks are essential to safe boating and must be
performed before starting the engine.
• Check the weather report, wind and water conditions.
• Check that required safety equipment and PFDs are
on-board and in proper operating condition.
• Check that the fire extinguisher is fully charged.
• Be sure the boat is not overloaded.
• Be sure the operator’s visibility is not obstructed.
• Check that all maintenance has been performed.
• Check the fuel system for leaks and fumes.
6 -1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-2
S e c t io n 6
S a f e t y E q u ip m e n t
Federal and local laws require certain safety equipment to be on-
board at all times. In addition, responsible boaters carry other
equipment in case of emergency. Check with local boating
authorities for any additional requirements over and above the
federal requirements.
F u e lin g
!
!
Explosion or fire hazard. Gasoline is
extremely flammable and highly explosive under certain
conditions. Turn the engine OFF and DO NOT smoke or
allow open flames or sparks within 50 feet (15 meters) of
the fueling area. Check your boat for fuel leaks and
fumes before, during and after each use. Maintain
contact between the fuel nozzle and the fuel tank to
prevent electrostatic spark. DO NOT use a plastic
CAUTION
To prevent engine damage not covered by
warranty, refer to your engine operation and
maintenance manual for recommended fuel type and
octane rating.
Take care not to spill gasoline. If gasoline is accidentally spilled,
wipe up all traces of it with dry rags and immediately dispose of the
rags properly ashore. Spilled fuel may “yellow” the gelcoat finish
and damage gunwale trim.
6 -2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-3
G e t t in g U n d e r w a y
Gasoline Containing Alcohol
CAUTION
DO NOT use any gasoline that contains
METHANOL. This fuel is very corrosive and will create
unsafe operating conditions to the boatʼs fuel system
and serious damage to the engine. Any engine damage
caused by the use of methanol will not be covered by
the engineʼs warranty.
The implementation of ethanol-based fuel is spreading rapidly
throughout the United States. As such, PCM Engines and
Nautiques by Correct Craft provide the following information
regarding the use of this fuel. This information addresses the use of
ethanol fuels in PCM Engines and Nautique boats.
CAUTION
Use of ethanol blended fuel rated E10 or less
is acceptable. DO NOT use fuels rated higher than E10.
Ethanol fuels rated higher than E10 could potentially
damage the engine and/or present an unsafe boat fuel
system. Damage to the engine resulting from the use of
ethanol fuel rated higher than E10 IS NOT covered by
the engineʼs warranty.
If ethanol blended fuel rated E10 or less is used, or if the presence
of alcohol is uncertain, inspections and service of the complete fuel
system are required more frequently. Any sign of fuel leakage or
deterioration must be repaired immediately before further engine
operation. It is also important to know that ethanol blended fuel
will act as a solvent and will attract and hold moisture.
NOTICE
Fuel system or engine damage caused by contamination from
water, foreign particles, sludge, or gums entering or forming in the
fuel system is not covered by the engine’s limited warranty.
6 -3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-4
S e c t io n 6
Without proper fuel filtration or fuel stabilization, ethanol blended
fuel may cause the following:
• Excessive moisture (water) can cause lean operation, hard
starting, and operating difficulties such as vapor lock and low
speed stalling, and can reduce fuel shelf life.
• Ethanol blended fuels acting as solvents can cause gum,
sediment, sludge and other particles to be loosened and
carried through the fuel system to the engine.
Fuel Stabilizer Recommendations for Ethanol Blended Fuels
The use of a commercially available fuel stabilizer, such as
STA-BIL®, is recommended when storing ethanol blended fuel for
more than two weeks.
When fueling:
1. Avoid fueling at night, except under well-lighted conditions.
Also avoid overfilling of the tank by monitoring the fuel level
gauge while fueling. Turn on the ignition without starting the
engine and monitor the gauge. Stop fueling as the gauge
approaches the ‘full’ level and turn off the ignition when
finished. Fuel spillage on our waterways will pollute our
environment.
2. Moor your boat securely to the dock. Know the location of the
fire extinguisher in case of emergency.
3. Close all doors, hatches, windows and other compartments.
4. Extinguish cigarettes, pipes, and all other flame producing
items.
5. Make sure all power is OFF, and DO NOT operate any
electrical switches.
6. Add fuel in accordance with the engine operator’s manual. DO
NOT overfill, and allow enough room for fuel expansion.
After fueling:
1. Tighten the fuel filler cap. Wipe up any spilled fuel.
2. Check all fuel lines, hoses and connections for leaks and
deterioration.
NOTICE
Each time you refuel, inspect all fuel lines, hoses and connections
for leaks and deterioration.
6 -4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-5
G e t t in g U n d e r w a y
B o a r d in g
When boarding the boat, always step in. DO NOT jump. Avoid
stepping on fiberglass or other potentially slippery surfaces. Board
one person at a time.
DO NOT board the boat while carrying gear. Set the gear on the
dock, board the boat and then pick up the gear.
Use the boarding platform to board from the water. To prevent
injury, make sure the engine is OFF when swimmers, divers and
skiers are boarding or even near the platform.
B o a t P la n in g
The performance of your Nautique boat depends on load weight
and distribution. DISTRIBUTE WEIGHT EVENLY, from bow to
stern, and also from port to starboard.
!
Overloading of passengers, personal
equipment and supplies could result in an accident,
especially in rough waters.
If your boat is equipped with a ballast tank or loaded, loss of
horizon may occur when you begin to plane your boat. Get on
plane immediately to restore the vision of your path. DO NOT
operate your boat if the loss of horizon prevents you from operating
it safely.
6 -5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-6
S e c t io n 6
P r e - O p e r a t io n C h e c k s
It is the owner’s responsibility to check all of the items listed below
to be certain all preparation steps are completed before you use
your boat. Checking these items periodically will soon become a
habit. If leaks or other abnormal conditions are found, stop using
the boat and contact your Nautique dealer to have the problem
corrected.
Get into the habit of performing these checks in the same order
each time so that it becomes routine.
• Make sure to check all safety items.
• Check that drain plug is properly installed.
• Check condition of propeller.
• Check that all batteries are fully charged and at the proper
level.
• Verify the amount of fuel in the fuel tanks.
• Be sure the lights, horn, bilge pumps and other electrical
equipment are in operating condition.
• Check that steering system operates properly.
• Make sure your float plan is submitted to a responsible
person.
• Refer to your engine operation and maintenance manual for
additional pre-operation checks.
6 -6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-7
G e t t in g U n d e r w a y
The following instructions are very important:
• Raise the engine hatch all the way up. Check to see if all the
engine drain plugs are in place. Make sure the hull drain
plug (T-handle) in the bilge area is installed.
• Look at all the hoses to make sure they are installed and the
hose clamps are tight. Close the engine hatch and turn on
the engine compartment blower. Run the blower at least
four minutes to remove fuel vapors that might be in the
bilge area and engine compartment before starting engine.
Remember, if you have detected the presence of fuel vapors,
do not start the engine until the source has been
determined, problems corrected and vapors removed.
• Check all gasoline line connections. Connections are located
at the fuel tank, the fuel control cell and the fuel injection
system. All Nautique boats are equipped with anti-siphon
valves on the outlet fittings of the fuel tanks to reduce the
chance of fuel siphoning from the fuel tank if a fuel hose
leaks or is severed.
• Fill the fuel tank and check for leaks. Check again for leaks
after the engine has run for a few minutes.
6 -7
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-8
S e c t io n 6
Checklist before starting boat:
1. Engine oil level - boat must be level.
2. Transmission oil level - boat must be level.
3. Shifting linkage and detent in forward, neutral and reverse.
4. Leaks (water, fuel and oil).
5. Coolant level (closed cooling system).
6. Operation of the throttle and transmission shift control.
7. Battery condition.
8. Visually inspect for any loose mounting fasteners.
9. Verify the emergency stop switch located by the throttle is fully
functional and the lanyard is not frayed or damaged. Clip the
safety lanyard securely to your body. Keep it attached at all times
while you are driving.
10. Check that engine cooling water (raw water) valve is open and
raw water strainer is clean.
CORC015
• Once the boat is in the water, visually check for water leaking
at the stuffing box. There should be no leakage from the
optional “dripless stuffing box” while a conventional stuffing
box must drip a moderate amount of water to properly
lubricate the drive shaft. If the “dripless stuffing box” is
leaking or water is coming in rapidly with the conventional
stuffing box, pull the boat out of the water and have your
Nautique dealer service the stuffing box.
6 -8
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-9
G e t t in g U n d e r w a y
• Make sure there are no ropes, gear bags, arms/ legs near the
belts and pulleys of the engine. Severe injury can result by
becoming entangled in the belts of the engine while it is
running. Make sure the boat is deep enough in the water to
supply the water intake with water to cool the engine. Move
the throttle into the NEUTRAL "straight up" position.
!
Fire or explosion hazard from fumes
accumulating in bilge area. Ventilate the engine
compartment by running the blower for four minutes,
especially after repairing or refueling and check for fuel
spills or leaks.
• Close the engine cover.
!
An engine guard which is not in place or
contact with any moving parts can cause death or
serious injury. The engine box cover is a machinery
guard. DO NOT operate your boat without the cover
closed and in place unless you are performing a check
or maintenance. Keep your hands, clothing, hair and
any other body parts away from any moving parts.
• Start the engine.
CAUTION
DO NOT continue to operate the starter for
more than 30 seconds without pausing to allow the
starter motor to cool off for five minutes. This allows the
battery to recover between starting attempts.
6 -9
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-10
S e c t io n 6
In order to prevent personal injury to you or others, the engine
cover must be closed whenever the engine is running.
• DO NOT operate the engine with the engine cover open or
while someone is in the area of an open engine cover.
• DO NOT open the engine cover unless the engine is turned
OFF and rotating parts are stationary and remain in a
stationary position.
IT IS RECOMMENDED THAT ALL WORK ON THE ENGINE BE
DONE BY TRAINED AND QUALIFIED SERVICE PERSONNEL.
During the warm up period, check the gauges for correct and
normal operation of all the systems:
• Oil pressure 35-80 psi, approximately at 2000 rpm
• Cooling water flow and water temperature 140-170°
• Cooling water temperature for fresh water systems: 170-210°
• Volts should rise to around 13-14V or higher
• Idle rpm (600-700) in gear
CAUTION
DO NOT operate at high rpms in NEUTRAL.
DO NOT shift into forward or reverse at engine speeds
above idle rpms.
DO NOT operate the engine without a cooling water
supply.
Damage to the water pump impeller and engine can
occur. If the engine does not start, refer to Section 9,
Troubleshooting.
6 -10
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-11
G e t t in g U n d e r w a y
If the engine does not start:
• If the fuel filter has been changed or if the fuel system was
run dry, it will be necessary to cycle the ignition start button
from the STOP position to the START position several times
until the fuel pumps build adequate pressure. The cycling of
the ignition is necessary because the fuel pumps will run
only one to two seconds when the ignition is turned on,
unless the engine starts. Keep the shifter/ throttle control in
NEUTRAL when starting the engine. If the throttle is
advanced, the computer will think the engine is flooded and
initiate a “clear flood” condition which will shut off fuel to
the engine and not allow it to start. The idle speed increase
is normally on hot or cold starts. This is programmed into
the computer. When the engine starts, the idle speed will
jump to approximately 1,500 rpm and quickly decrease to
between 750 and 900 rpm.
• Check for gasoline and cooling water leaks on the engine.
• Check for cooling water circulation (look at the raw water
strainer at the rear port side of the engine for water
movement).
Flooded Engine
If your engine does become flooded, use caution when attempting
to start the engine. Push in the transmission disengagement button
at the bottom of the shifter/ throttle control handle and advance
the throttle to the FULL THROTTLE position. By pushing the
button in, the shift linkage is disengaged and the transmission
remains in NEUTRAL during the starting procedure. Run the
starter until the engine starts. DO NOT operate the start switch for
more than 30 seconds. Allow the starter to cool.
We suggest you bring your boat back to your Nautique dealer after
25 hours of operation for an inspection of the shaft alignment,
stuffing boxes adjustment, and the fuel system checked for leaks.
This is not a free service. Follow Pleasure Craft Marine’s (PCM)
recommendations in the maintenance section for additional
service to the engine. Consult your Nautique dealer to determine
what charges will apply.
6 -11
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-12
S e c t io n 6
When the engine starts, move the throttle lever back until the
engine is running about 2,500 rpm or less. Check the gauges for
normal readings and let the engine run for a minute to burn the
excess fuel. If the gauge readings are abnormal, stop the engine
and contact your Nautique dealer. When the engine runs normally,
check the engine for fuel, water and exhaust leaks. If there are
leaks, stop the engine and correct them before you continue.
NOTICE
Read the “Notice to Dealer” located in your Skipper’s Kit. It
contains pre-delivery checks and adjustments which must be
performed by your Nautique dealer. It is still the boat owner’s
responsibility to make sure they were performed. This will also help
you become more familiar with your boat and its systems. If you
have any questions regarding this notice, contact your Nautique
dealer.
After your initial run:
• Check the engine oil level
• Check the transmission oil level
• Check the V-Drive oil level
• Check for leaks (water, fuel and oil)
• Check that engine frame bolts and mounts are tight
• Check that throttle and shift control operates correctly
NOTICE
If the engine backfires when you try to start it, the problem may be
more serious than flooding.
•
DO NOT CONTINUE TRYING TO START THE
ENGINE.
•
CONTACT YOUR NAUTIQUE DEALER OR A
QUALIFIED TECHNICIAN TO CORRECT THE
PROBLEM.
DO NOT keep trying to start the engine under these conditions.
Engine damage or personal injury can result.
6 -12
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-13
G e t t in g U n d e r w a y
Break In Procedure
Make sure all your passengers are properly seated before starting
the break in procedure. After the engine is thoroughly warmed up
and you have driven the boat into a large open area, advance the
throttle to wide open until the maximum rpms are reached. DO
NOT exceed 5,000 rpm. Reduce the throttle to 2,800-3,000 rpms
and cruise at or below this speed for 30 minutes. Reduce the speed
to idle, advance the throttle to wide open and operate at that speed
for one minute; reduce to the previous cruising speed for a few
minutes and repeat. Accelerating from idle speed to wide open
assists in seating the piston rings. This cycle can be repeated from
time to time during the first five hours of operation. DO NOT
operate engine at full throttle for longer than one to two minutes.
CAUTION
Follow these procedures only when
conditions are such that you can drive the boat safely.
DO NOT attempt to break in an engine by letting it idle at
the dock.
Propeller Selection
The maximum rpm of the engine at full throttle under normal load
conditions can be controlled by propeller pitch, diameter and
design. It is essential the propeller does not underload or overload
the engine.
Propeller Overloading, results in low rpms at wide open throttle
will give poor performance, poor fuel economy and eventually
result in engine damage.
Propeller Underloading, if operated with a propeller that has too
little pitch or diameter, poor performance will result.
6 -13
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-14
S e c t io n 6
NOTICE
Running your boat in shallow water can cause propeller shaft,
strut, propeller and rudder damage and sand and silt to be pulled
into the cooling system. This will cause excessive water pump wear
and can clog the water passages in the engine. Heavy weed growth
in the water can plug the raw water strainer and oil coolers and
cause engine damage. There is a raw water strainer located near
the rear of the engine to strain the water before it goes into the
transmission cooler and then the engine. Check this every time you
use your boat to make sure it is not clogged.
Refer to Section 1, Hazardous Conditions, Boating Safety.
If the engine fails to start or is not operating properly, contact your
Nautique dealer for assistance.
S h if t in g
!
Boat movement without making sure your
path is clear can cause death or serious injury. Make
sure there are no swimmers or obstacles in the water
near you.
Keep the control lever clean and clear of obstructions. Refer to
your engine operator and maintenance manual for shifting
information.
Always pause in NEUTRAL before shifting from reverse to forward
and from forward to reverse.
S t e e r in g
Practice steering your boat. Make sure the steering system is
working correctly and is properly maintained.
!
The steering system must be in good
operating condition for safe boating. Frequent
inspection, lubrication and adjustment by your Nautique
dealer is recommended.
6 -14
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-15
G e t t in g U n d e r w a y
S t o p p in g
Stopping the engine immediately after operating at high speed is
not recommended. Allow the engine a two to three minute cool-
down period at idle or low speed.
Refer to your engine operator and maintenance manual for
stopping information.
D o c k in g
!
There is a crushing hazard between the
boat and other objects that could cause death or serious
injury. DO NOT use your hands, arms or another part of
your body to attempt to keep the boat from hitting other
objects, especially a dock.
Approach a dock slowly and use caution. Plan your maneuvers
ahead of time. Allow wind and current movement to help
maneuver your boat.
Come to a stop a short distance from the dock, then proceed slowly.
• Have your fenders and mooring lines ready.
• Observe how the wind and current are moving your boat.
Approach the dock with the boat pointed into the wind, if
possible.
• If possible, throw a line to a person on the dock and have
that person secure a bow line. If no one is on the dock,
maneuver as close as you can, then secure any line to a
piling or dock cleat.
Before tying up your boat, be sure to use enough fenders to protect
the boat from damage. If possible, tie up the bow toward the waves
with a good quality double-braided nylon line. Tie up only to the
lifting rings, tie down eyes or cleats; DO NOT use the handrails or
windshield frame. If the boat is to be moored for a long period of
time, use chafing protectors on the lines to protect the gelcoat
finish. Leave a little slack in the lines to allow for some wave
movement or tidal action as applicable.
When departing, cast off the bow line and move away. If the wind
or current is pushing away from the dock, cast off all lines and allow
to drift until you are clear.
6 -15
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 6_2008.qxd:Naut Air Sec 6.qxd 6/25/08 12:34 PM Page 6-16
S e c t io n 6
N O T E S
6 -16
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 7_2008.qxd:Naut Air Sec 7.qxd 6/24/08 4:00 PM Page 7-1
S e c t io n 7
R u n n in g
Nautiques by Correct Craft urges you and all others operating your
boat to seek certified instruction from the local boating authorities.
This section is designed to present the most basic operational
principles. It is NOT intended to cover all conditions encountered
during operation. Therefore, the principles in this manual are
limited to the facts related directly to the operation of your boat,
while the responsibility for the proper application of these
principles belongs to you.
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 7_2008.qxd:Naut Air Sec 7.qxd 6/24/08 4:00 PM Page 7-2
S e c t io n 7
M a n e u v e r in g T e c h n iq u e s
Steering response depends on three factors: rudder position,
motion and throttle.
Maneuvering in congested areas and advanced courses requires
mastering and good “Rules of the Road” ethics. Your Nautique boat
is designed to be responsive and agile enough to meet the
challenge of these conditions.
STERN
CIRCLE
BOW
CIRCLE
CORC135
Maneuvering
High speed maneuvering is relatively easy and takes little practice
to learn. Slow speed maneuvering is far more difficult and requires
time and practice to master.
When making tight maneuvers, it is important to understand the
effects of turning. Since both thrust and steering are at the stern of
the boat, the stern will push away from the direction of the turn.
The bow follows a smaller turning circle than the stern.
!
Quick maneuvers can cause people and
objects in the boat to be thrown about resulting in death
or serious injury. DO NOT make quick or high-speed
maneuvers when you or your passengers are not
prepared.
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 7_2008.qxd:Naut Air Sec 7.qxd 6/24/08 4:00 PM Page 7-3
R u n n in g
The effects of unequal propeller thrust, wind and current must also
be kept in mind. While wind and current may not always be
present, experienced boaters will use them to their advantage.
Unequal thrust is an aspect shared by all single-engine propeller-
driven watercrafts.
The 210, 211, 220, 230 and 236 have a counterclockwise rotation
propeller which tends to cause the boat, steering in the straight
ahead position, to drift to port when going forward or backward. At
high speed, this effect is usually unnoticed, but at slow speed,
especially during backing, it can be powerful. For this reason, many
veteran boaters approach the dock with the starboard side of the
boat toward the dock, if possible.
Stopping (checking headway) is a technique that must be
developed. Reverse thrust is used to slow and stop the boat. The
momentum of the boat will vary according to the load as well as the
speed. Make it a practice to slow to idle (no-wake) speed before
shifting into reverse.
It is best to learn maneuvering skills in open water away from traffic.
Adequate practice is the only way to develop your boating skills.
T o w P a t t e r n
A large loop pattern is preferred for beginners. This pattern does
not require the skier to cross the wake. As the skier’s skills improve,
a looped end or dumb bell pattern may be used. The dumb bell
pattern provides a long straight course which allows the wake to
disperse, leaving the skier with a smooth water surface. The dumb
bell pattern is popular with ski tournaments and clinics.
KCB-011
Dumb Bell Ski Pattern
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 7_2008.qxd:Naut Air Sec 7.qxd 6/24/08 4:00 PM Page 7-4
S e c t io n 7
F r e e z in g T e m p e r a t u r e s
When the boat is removed from the water, drain the cooling and
heater system (as equipped) completely.
A n c h o r in g
There are many types of anchors available on the market. The
choice of one anchor over another depends on many factors. An
anchor will usually hold best in a mixture of mud and clay or in
hard sand. A Danforth anchor is recommended for general
boating. For more information on anchors, contact your Nautique
dealer.
!
Improper use of an anchor can pull a boat
underwater causing death or serious injury. Anchor
from the bow, NOT from the stern.
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 7_2008.qxd:Naut Air Sec 7.qxd 6/24/08 4:00 PM Page 7-5
R u n n in g
KC-1571C
Danforth Anchor
Dropping Anchor
• Make sure the line is tied to the anchor and tie the other
end to the forward cleat or bow eye.
• Head the boat into the wind or current over the spot where
you want to lower the anchor. Spot the boat before lowering
the anchor.
• When the anchor hits bottom, slowly back up the boat,
keeping tension on the line. Let out an anchor line that is
six to seven times the depth of the water. For example, if you
are in 10 feet (3 m) of water, let out 60 to 70 feet (18 to 21
meters) of line.
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 7_2008.qxd:Naut Air Sec 7.qxd 6/24/08 4:00 PM Page 7-6
S e c t io n 7
LINE SIX TO SEVEN
TIMES DEPTH OF WATER
CORC136
Anchoring
• Pull on the line to make sure the anchor is holding.
• Occasionally check your position against the shoreline. If the
anchor is dragging and you are drifting, reset the anchor.
Weighing (Pulling In) Anchor
Start the engine and move forward until the anchor line is straight
up and down. Pull hard to lift the anchor from the bottom material.
If the anchor is caught on the bottom, attach a line to the bow cleat
so that it is taut. The up and down motion of the bow from wave
action may lift the anchor from the bottom. If the anchor remains
caught, let out a few more feet of line and attach it to the bow cleat.
Slowly maneuver the boat around the anchor until the anchor pulls
loose. Be sure to keep the line tight during this procedure.
7-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 7_2008.qxd:Naut Air Sec 7.qxd 6/24/08 4:00 PM Page 7-7
R u n n in g
P e r f o r m a n c e B o a t in g
!
Failure to maintain control can result in
death or serious injury. Always keep one hand on the
steering wheel and the other on the control lever. If the
boat begins to operate in an unsafe way, adjust speed
and course as necessary to regain control.
Your Nautique boat is a high performance boat. DO NOT be
tempted to push your boat to its limits until you are completely
familiar with its operating characteristics.
Nautique boats are the ones of choice of the better professional and
amateur ski shows and tournaments. You may have seen drivers put
their Nautique through extreme maneuvers. These drivers are paid
professionals on a closed course with hundreds of hours of
experience. DO NOT attempt extreme maneuvers without proper
training.
We recommend that you never operate the boat without first having
an initial orientation and familiarization/ demonstration ride with
your dealer or an operator experienced with the boat/ engine
combination. All boats perform differently.
The operator should have at least ten hours of experience with the
boat before any full throttle operation. DO NOT operate your boat
until you are completely experienced with its handling
characteristics.
P r o p e lle r s
Your Nautique boat is equipped with a propeller best matched to its
engine and boat combination. If you feel you are experiencing poor
performance, contact your Nautique dealer. Care and selection of
your propeller is very important to proper boat operation.
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 7_2008.qxd:Naut Air Sec 7.qxd 6/24/08 4:00 PM Page 7-8
S e c t io n 7
N O T E S
7-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-1
S e c t io n 8
C a r e a n d M a in t e n a n c e
This section describes how to care and maintain your Nautique
boat. Periodic inspection and maintenance of items listed in this
section is absolutely necessary.
Winterization and some engine maintenance functions are best
performed by your Nautique dealer. Some maintenance items that
can be done by you or your dealer are listed below. We suggest that
you familiarize yourself with these even if you have your dealer
service your boat.
G e n e r a l M a in t e n a n c e
1. Read engine operator and maintenance manual very carefully.
2. Check for fuel line leaks every time you use the boat.
3. DO NOT start your engine if gasoline odor is present. Gasoline
fumes are highly explosive. Before starting your engine, open
the engine cover, inspect the engine compartment for gasoline
fumes and operate the blower for at least four minutes. Run
your blower when operating at slow speeds. If fuel vapors are
present, do not start the engine. Check all hoses and fittings to
determine the source of the vapor. Make the necessary
adjustments or take the boat to your local dealer to eliminate
the fuel vapor.
Fumes accumulating in bilge area present a
!
fire or explosion hazard which could cause
death or severe injury. Ventilate the engine compartment by
running the blower for four minutes, especially after repairing
or refueling and check for fuel spills or leaks. If you smell
gasoline vapor or see liquid gasoline, DO NOT start the
engine.
8 -1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-2
S e c t io n 8
4. When servicing the ignition switch or any wiring, always
disconnect the battery cables from the battery.
5. Check for water circulation when the engine is running.
Exhaust should contain steady flow of water. In closed cooling
systems, make sure the coolant in the cooling system is at the
proper level.
Engine Intake Water Strainer
Visually inspect the engine intake water strainer for debris before
each use. To clean the strainer, close the engine intake water valve
and unscrew the strainer bowl (A). DO NOT lose the rubber O-ring
(B) that seals the bowl to the cap. Carefully remove the screen (C).
RAW WATER
STRAINER
OFF
ON
WATER
VALVE
CORC067
C
B
A
CORC078
8 -2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-3
C a r e a n d M a in t e n a n c e
Clean debris from the bowl and screen and rinse parts in fresh
water. Insert the screen, place the O-ring in the groove of the bowl
and screw the bowl on hand tight. Be sure to open the water valve
before starting the engine.
Some engines are equipped with a closed cooling system with a self-
contained reservoir for engine coolant. Self-contained systems are
equipped with a heat exchanger which uses raw water to cool the
coolant. All raw water systems are equipped with a valve and
strainer.
B ilg e P u m p s
Check your bilge pumps often to make sure they are operating
efficiently. There are two bilge pumps: one is at the rear of the boat
near the rudder and under the floor by the forward bulkhead
located next to the fuel tank. To keep the pumps from getting
clogged, remove any debris you find in the bilge. Wash the bilge
with a good biodegradable household detergent or a bilge cleaner
available at your Nautique dealer or a marine supply store. Rinse
with water with your bilge pumps running. If your pumps seem to
lag, remove the top of the pump from the base and check the
impeller to make sure there is no debris inside. See your dealer if
there is still a problem with the pumps.
8 -3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-4
S e c t io n 8
P r o p e lle r
CAUTION
• A propeller can be very sharp. Be careful when you
handle it. Wear a pair of protective gloves when
handling any propeller.
• Remove your key from the ignition and remove the
Emergency Stop Switch clip from the switch to
prevent accidental starting of the engine.
• DO NOT reuse the nylon locknut or the cotter pin.
• DO NOT use a damaged propeller. A damaged
propeller can damage your engine and boat.
Removal
1. Remove the cotter pin from the propeller shaft and discard.
2. Wedge a piece of 1" x 4" wood between the propeller blade and
the starboard side of the strut and rudder.
3. Remove the nylon locknut and discard.
8 -4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-5
C a r e a n d M a in t e n a n c e
Use a propeller puller to remove the propeller, then remove the
key from the keyway. Inspect the keyways and key for any damage.
A
C
B
CORC047
Installation
Before placing the propeller on the shaft, look at the keyway on the
shaft and in the propeller. Make sure the key slides freely in the
shaft keyway and the propeller keyway. DO NOT use the propeller
to advance the prop onto shaft.
If the key has burrs, remove them by filing the flat sides or replace
the key. DO NOT file the key beyond its normal shape or size.
1. Rotate the shaft until the keyway is “up.”
2. Place the key in the shaft keyway. The propeller will only slip on
in one direction. Rotate the propeller so the keyway in the
propeller is aligned with the keyway on the shaft. Once it is
aligned, push the propeller onto the shaft. You’ll hear a solid
“thunk” or feel it, as the propeller is seated.
3. Wedge a piece of 1" x 4" wood (A) between the propeller blade
and the port side of the strut and rudder.
4. Install a new nylon locknut (B) and torque the nut to maximum
of 30 ft-lbs (40.7 N•m).
5. Install new cotter pin (C). Bend the retaining ends of the cotter
pin in the opposite directions.
8 -5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-6
S e c t io n 8
P r o p e lle r S h a f t S t u f f in g B o x
The stuffing box is designed to prevent water from coming through
the through-hull fittings. These are found on the propeller shaft
where the shaft goes through the hull and where the rudder comes
up through the bottom of the boat. These devices contain a
lubricated fibrous packing that acts as a seal.
Check the propeller shaft stuffing box frequently for excessive
leakage. The engine must be OFF. A leaking rate of a few drops per
minute is acceptable and expected for proper lubrication. Raise the
engine cover and remove the storage bulkheads. If you see a steady
stream of water or an excessive drip rate, return your boat to your
Nautique dealer for service.
T h r o u g h - H u ll F it t in g s
All fittings that actually pass through the hull on the wetted surface
are caulked in. These are not serviceable and must not be tampered
with.
Q u ic k O il D r a in S y s t e m
Change the engine oil after the first 25 hours of operation, then
after every 50 hours. The boat must be removed from the water to
use the quick oil drain system. There is a drain hose attached to the
bottom of the oil pan with a small plug screwed into the loose end
of the hose. Remove the drain plug (T-handle) (A), located in the
bilge area, and put the end of the drain hose through the drain
hole.
Make sure there are no kinks or sharp bends in the hose. Remove
the plug at the end of the hose and drain the oil into a container
under the boat. The engine will drain most efficiently when the oil
is warm. Allow several minutes for the oil to settle and drain.
Dispose of used oil in an environmentally safe manner.
NOTICE
Be sure the engine is off when you are draining your oil.
!
Prolong or repeated contact of used
engine oil can cause death or serious injury. Wash
affected area immediately with soap and water.
8 -6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-7
C a r e a n d M a in t e n a n c e
S a lt W a t e r B o a t in g
NOTICE
If you use your boat in salt water or other unusual water
conditions, fresh water flush your engine and cooling system with
freshwater.
Nautiques by Correct Craft offers an optional fresh water flush kit.
The relief valve in this kit prevents excessive water pressure to your
engine. Excess water pressure can damage the engine. This is the
only system we recommend if you use your boat in salt water or
unusual water conditions. Flushing the system by running the boat
in fresh water is another good way to flush the engine, but it must
be done immediately.
F r e s h W a t e r F lu s h in g K it -
O p t io n a l
The optional freshwater flushing kit allows you to flush the water
system after your boat is operated in salt water, brackish water or
unusual water conditions.
The relief valve in this kit prevents excessive water pressure to
your engine. We recommend using this system if you use your
boat in salt water or unusual water conditions. Flushing the system
by running the boat in fresh water is another good way to flush
the engine, but it must be done immediately.
DO NOT connect the flushing kit to a water source which exceeds
normal municipality water pressure.
8 -7
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-8
S e c t io n 8
B a t t e r y M a in t e n a n c e
!
Explosion or fire hazard from vented
fumes can cause death or serious injury.
• Wear eye protection and rubber gloves when working
on or around batteries.
• DO NOT charge or use a battery booster to start your
engine.
• Charge the battery outside of the boat.
• DO NOT smoke or bring a flame near a battery at any
time.
• DO NOT have your head directly above a battery when
making or breaking electrical connections.
• DO NOT use a metal object to spark between battery
posts to check if the battery is charged.
Take care when connecting or disconnecting a battery charger. Be
sure the charger is turned OFF and unplugged from power source
when you clip ON/ OFF the connecting clamps.
Make sure you have a solid connection with the charging clamps.
Poor connections are common causes of electrical arcs and engine
problems. Follow instructions.
DO NOT make or break electrical circuits at the battery terminals;
a spark will occur when a live circuit is opened or made. Turn off all
components.
Use a voltmeter or hydrometer to check the battery charge
condition.
The battery cables should be removed from the battery when the
boat is placed in storage, on display or in transit. This will eliminate
the possibility of the engine accidentally starting without a supply of
cooling water and may damage the engine.
8 -8
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-9
C a r e a n d M a in t e n a n c e
A
CORC212
+ = red positive (A)
- = black negative (not shown)
To clean your battery, remove and wash down the battery case with
a diluted ammonia or baking soda/ water solution to neutralize the
acid, then flush with fresh water. Keep the fill/ vent caps tight so the
neutralizing solution does not get into the battery cells.
The electrolyte level should be checked every 30 days. Add only
distilled water to maintain the level between the top of the plates
and the bottom of the fill/ vent cap. DO NOT overfill. Remember
batteries contain sulfuric acid which can cause severe burns.
8 -9
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-10
S e c t io n 8
G e lc o a t M a in t e n a n c e
Your Skipper’s Kit included samples of quality boat care products
recommended by Nautiques by Correct Craft. Nautiques by Correct
Craft is proud of its heritage and wants you to feel this pride every
time you use your boat.
Regular maintenance is the key to keeping your hull and deck
surfaces in good condition. Sun exposure, residue from trees and
minerals in the water affect your boat’s finish.
To help maintain the shine of your boat, wash the hull with a mild
bio-degradable detergent after each use. This will help to remove
any debris and waterborne materials that are on the hull. Use a soft
sponge or towel and dry with a chamois cloth to prevent water
spots.
Wax the hull sides and deck regularly with a high quality wax.
Waxes and polishes are available at your Nautique dealer and
marine supply stores. Always follow the directions on these
products carefully before you use them.
The hull bottom is an especially important area to keep clean since
any buildup of water scum and algae will create drag and reduce
the boat’s efficiency. If you must leave your boat in the water, there
are compounds to remove algae buildup on your hull. Some of
these can be caustic. Pay special attention to the cautions on the
label of these coatings. Ask your Nautique dealer for advice on
which work best in your area.
If your boat’s gelcoat develops a chalky look over a period of time
due to exposure to sun, there are gelcoat buffing and polishing
compounds available at your Nautique dealer and marine supply
stores. DO NOT use common household scouring pads or
powders.
If you will be keeping your boat in the water for ANY period of time,
we suggest that the wetted surface of the hull be painted with an
epoxy paint formulated for blister protection.
8 -10
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-11
C a r e a n d M a in t e n a n c e
C a r e o f M e t a l
• Aluminum care
• Stainless care
• Chrome
• Anodized towers
• Aluminum Clear Coat Towers
Keep all metal work rinsed and wiped dry. Periodically polish it with
a quality commercially available metal polish to remove substances
such as air-borne pollution and natural body oils from your hands.
Do not use citrus cleaners on stainless steel or wax on anodized
towers. For best results on the Aluminum Clear Coat Towers, use
cleaners and waxes suitable for clear coat finishes.
C a r e o f G la s s
Your windshield, mirrors and gauge faces all deserve the same
attention as the other parts of your boat. Clean them often with
quality commercially available glass cleaners.
V in y l M a in t e n a n c e a n d
C le a n in g
Nautiques by Correct Craft has selected the finest marine grade
vinyl for your Nautique. It is important to keep it clean at all times.
There are some substances that will stain the vinyl if you leave them
on for even a short period of time. Remove any contaminant and
clean the area immediately. DO NOT use Formula 409® Cleaner,
Fantastik® or any silicone-based products. Certain household
cleaners, powdered abrasives, steel wool, industrial cleaners, dry
cleaning fluids and lacquer solvents can cause damage and
discoloration. DO NOT use these cleaners.
8 -11
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-12
S e c t io n 8
Common stains and steps to treat:
Step #1
Step #2
Step #3
Chewing gum
Eye shadow
Engine oil
D
E
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
D then A
E then B
B
C
D
A
D
D
A
D
A
A
A
D
A
D
E
B
B
A
Spray paint
Mildew or wet leaves *
Shoe polish *
Yellow mustard
Oil based paint (fresh)
Oil based paint (dried)
Suntan lotion *
Tar/ Asphalt
Lipstick
Latex paint
Crayon
Ketchup
Grease
Ball-point ink *
Permanent marker *
Coffee, tea, chocolate
E
B
Use the chart above to clean common stains:
A. Medium-soft brush, warm, soapy water/ rinse/ dry
B. Meguires Quick Clean #52
C. One(1) tablespoon ammonia, 1/ 4 cup hydrogen peroxide, 3/ 4
cup water rinse/ dry
D. Wipe or scrape off excess (chill gum with ice)
E. Denatured Alcohol/ rinse/ dry
After all cleaning methods, rinse well with water.
*Suntan lotion, shoe polish, wet leaves and some other products
contain dyes that stain permanently.
8 -12
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-13
C a r e a n d M a in t e n a n c e
T u n a b le R u d d e r
The Tunable Rudder* is designed to
offer easy steering adjustment. This
system uses a composite tuning foil
which is located at the upper aft corner
of the rudder blade. Use a Phillips head
screwdriver to adjust the foil. Loosen
the two screws in the relief slots of the
CORC045
tuning foil.
If the boat is pulling port (A), rotate the foil to port (B) and tighten
screws. If the boat is pulling starboard (C), rotate the foil to
starboard (D) and tighten screws. Always remember that movement
of the trailing edge of the foil to one side will cause the steering to
pull to the opposite side.
NOTICE
After each adjustment, test run and adjust again if necessary.
A
C
CORC162
B
D
*Manufactured under license from National Products, Inc. U.S. patent 5,746,147.
8 -13
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-14
S e c t io n 8
Rudder Remote Lube Fitting
The remote lube fitting allows for easy access to lubricating the
rudder. The remote lube fitting is located at the stern of the engine
compartment. Use a quality marine grease and gun. Connect the
grease gun to the fitting and apply a light pressure to the gun until
you feel a slight resistance.
8 -14
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-15
C a r e a n d M a in t e n a n c e
T r a n s m is s io n
!
Burn hazard from hot transmission fluid
can cause serious injury. Do not remove the
transmission drain/fill plug while the engine is running
or while the transmission is hot.
Allow the transmission to cool and check with the boat level.
1. Remove the drain/ fill plug from the transmission.
2. Verify the fluid level; the fluid level should be at the bottom of
the threaded hole. If low, add the specified fluid through the
threaded hole to the proper level.
NOTICE
The transmission fluid is a very high viscosity, to make adding
fluid easier, remove both fill plugs.
3
Replace the drain/ fill plug and tighten securely.
Oil Fill/Drain
Oil Fill/Drain
Plug
PL E ASURE CRA FT
PEONWGINEERGRPOLUUPS
Plug
RATI O
1.48
MADE IN USA
Raw Water
Drain Plug
CORC210
8 -15
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 8_2008.qxd:Naut Air Sec 8.qxd 6/25/08 12:42 PM Page 8-16
S e c t io n 8
Shift Cable
Lubricate pivot points and exposed cable with SAE 30W-30 engine
oil.
LUBRICATION
POINTS
CORC211
8 -16
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 9_2008.qxd:Naut Air Sec 9.qxd 6/24/08 4:10 PM Page 9-1
Section 9
Troubleshooting
The following chart will assist you in finding and correcting minor
problems with your Nautique boat. Refer to your engine operation
and maintenance manual for more detailed information for any
problem concerning the starting, shifting or operation of the
engine.
Some problems may require the skills of a trained technician and
special service tools. Please contact your Nautique dealer for
assistance.
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 9_2008.qxd:Naut Air Sec 9.qxd 6/24/08 4:10 PM Page 9-2
Section 9
Trouble Check Chart
Performance
Symptom
Possible Cause
Starter motor will not operate
• Shift handle not in NEUTRAL
• Battery Selector switch OFF
• Battery and electrical connection
loose or corroded
Engine will not start
• Emergency stop switch not in
place
• Starting procedure not followed
• Fuel tank empty
Poor boat performance
• Contaminated fuel
• Clogged fuel filter
• Uneven load distribution
• Improper propeller selection
• Marine growth on hull
• Engine problem
Poor gas mileage
Excessive vibration
• Marine growth on hull
• Engine problem
• Damaged or fouled propeller
• Misaligned propeller shaft
coupling
• Bent propeller shaft
• Engine problem
Engine runs but boat
makes little or no
progress
• Fouled or damaged propeller
• Engine problem
Steering problem
• Corroded steering cable
• Rudder worn
Throttle/ shifting problems
• Corroded cables
• Defective throttle return spring
• Low transmission fluid level
• Sticking transmission shift lever
9-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 9_2008.qxd:Naut Air Sec 9.qxd 6/24/08 4:10 PM Page 9-3
Troubleshooting
Electrical
Symptom
Possible Cause
Electrical problem
• Open circuit breaker or blown
fuse
• Loose wiring connection
• Defective switch or gauge
• Open circuit breaker tripped or
in OFF position
Dim or no lights
• Battery discharged
• See Page 4-30
9-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 9_2008.qxd:Naut Air Sec 9.qxd 6/24/08 4:10 PM Page 9-4
Section 9
NOTES
9-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 10_2008.qxd:Naut Air Sec 10.qxd 6/24/08 4:12 PM Page 10-1
S e c t io n 10
S t o r a g e
L if t in g R in g s a n d L if t in g E y e s
The 211 has lifting rings at the bow and at the stern. The 210, 220,
230 and 236 have a bow lifting ring and stern lifting eyes. These are
designed to lift your boat in a steady and secure manner. The
winch, hooks and other components of the lifting mechanism have
sufficient capacity sufficient for your boat. Refer to Section 3
Specifications. The weights listed in the specifications are dry
weight. You must add the weight of the battery, fuel and gear to the
dry weight.
If the lifting eyes at the stern of the boat are below the boarding
platform, the platform MUST BE removed before the boat is lifted.
The platform MUST BE reinstalled before the boat is put back into
service.
CORC060
10 -1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 10_2008.qxd:Naut Air Sec 10.qxd 6/24/08 4:12 PM Page 10-2
S e c t io n 10
CAUTION
Drain the bilge and / or launch control system
and/or aftermarket water bladder(s) to eliminate excess
water before you lift the boat.
NOTICE
Only use a hook that will pass easily through the lifting rings or
eyes without binding. A hook that is too large or off-center could
break the lifting rings or eyes. DO NOT use a sling to lift the boat.
Damage to your boat can occur.
If your boat is equipped with a retractable lifting eye, it can be used
for lifting your boat.
CORC055
10 -2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 10_2008.qxd:Naut Air Sec 10.qxd 6/24/08 4:12 PM Page 10-3
S t o r a g e
W in t e r iz in g Y o u r B o a t
Winter storage procedures vary depending on climate, type of
storage and length of storage. Check with your dealer/ storage
facility manager for their advice on what works best in your climate.
Winterization functions are best performed by your Nautique
dealer. Refer to your engine operation and maintenance manual
for more information.
When storing your boat up on a rack system, it is important the
racks adequately support the hull bottom.
If you do not have a trailer, support the boat like a Nautique dealer
recommended trailer. It is important to have an even weight
distribution.
If you do not have a dealer or marina nearby and must arrange
winter storage yourself, contact your regional warehouse.
If you use a mooring cover, DO NOT put it on when the interior of
the boat is wet and/ or hot. It will trap moisture and lead to mildew
on the carpet and/ or vinyl. Make sure your mooring cover allows
air to circulate, even if you have to leave a portion of the cover off.
RAW WATER
STRAINER
OFF
ON
WATER
VALVE
CORC067
10 -3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 10_2008.qxd:Naut Air Sec 10.qxd 6/24/08 4:12 PM Page 10-4
S e c t io n 10
C
B
A
CORC078
The raw water strainer bowl (A) remains full of water even after the
rest of the engine cooling water system is drained. To properly
winterize your boat, the strainer bowl must be removed and
emptied. DO NOT lose the rubber O-ring (B) that seals the bowl to
the cap. Clean screen (C) if required. If the water is not removed,
the bowl can be damaged. A damaged strainer can cause
overheating problems during the next season.
10 -4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 10_2008.qxd:Naut Air Sec 10.qxd 6/24/08 4:12 PM Page 10-5
S t o r a g e
C h e c k F o r W a t e r In Y o u r F u e l
S y s t e m
A small amount of water left in the fuel system for several months
can result in damage to the fuel system and engine. If you are
storing your boat for the winter, it is a good practice to remove any
water in the fuel system.
The Fuel Control Cell can be drained by removing the drain plug
at the bottom of the canister.
1. Loosen the return fuel hose to provide an incoming air source.
2. Clamp the return fuel line some way to minimize the amount
of fuel that may drain.
3. Once the canister is drained, coat the threads of the drain plug
with a fuel resistant pipe thread sealer, then replace and tighten
the plug.
4. Reconnect the fuel hose, and tighten the hose clamp. The
threads must be sealed properly to avoid a possible fuel leak.
Check your Fuel Control Cell once each year for signs of water in
the canister. If it appears there is water buildup in the canister, see
your Nautique dealer for service.
An empty fuel tank can accumulate water inside by changing
temperature and repeated cycles of condensation on the inner
surfaces of the tank. If the fuel tank is kept at about 3/ 4 full during
storage, less water can condense, limiting the buildup of water in
the fuel tank.
Fill the tank to 3/ 4 full maximum during storage to eliminate the
possibility of fuel expansion problems caused by temperature
changes. This minimizes overflow of fuel from the fuel vent. Not
only can this overflow be hazardous, but it will also adversely affect
decals and pin striping on the boat.
10 -5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 10_2008.qxd:Naut Air Sec 10.qxd 6/24/08 4:12 PM Page 10-6
S e c t io n 10
Add a good quality fuel stabilizer to the fuel prior to winterizing to
slow down the rate of fuel decomposition. You can purchase a fuel
stabilizer at your servicing dealer, most marinas or an auto supply
store. Add the stabilizer to the tank.
If you did not add the stabilizer previously, run the engine to
circulate fuel throughout the system. Remember, always follow the
fuel stabilizer manufacturer’s recommendations for proper mixing.
NOTICE
Gasoline expands when the temperature increases. Never store your
boat with more than 3/ 4 of a tank.
Refer to the engine’s owner’s manual for winterization of the
engine.
W in t e r iz in g B a lla s t T a n k s
( if e q u ip p e d )
NOTICE
It is extremely important to protect the Flight Control System
during freezing temperatures and during long periods of non-use.
When following this procedure, remember to protect our natural
resources by using environmentally friendly products; and to
always discard in an environmentally friendly manner.
1. Make sure your boat is out of the water, the tanks are
completely drained and the tank water intake/ drain valves are
open.
2. Use a 50/ 50 mixture of an environmentally friendly antifreeze
and fresh water.
3. Pour an even amount, approximately 1 gallon (3.8 liters) of the
antifreeze mixture into each tank’s vent.
4. Place a container under the intake/ drain of the tank you are
winterizing to catch any spilled mixture.
5. Operate the pump in the drain mode for two seconds and shut
off. Repeat procedure for other tank(s).
6. Close the tank’s water intake/ drain valves.
When returning your boat back to service, drain the remainder of
the mixture before getting onto the water.
10 -6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 10_2008.qxd:Naut Air Sec 10.qxd 6/24/08 4:12 PM Page 10-7
S t o r a g e
T r a ile r / T r a ile r in g
Hitch
If you do not already have a trailer hitch installed on your vehicle,
go to a reputable hitch company to have the proper size hitch
installed. Always use a hitch rated with the appropriate capacity to
match the trailer and boat’s gross weight.
!
Loss of control can cause death or
serious injury. DO NOT attempt to tow more than one
trailer at a time behind your vehicle. Attempting to tow
an additional trailer will adversely affect the trailer
tongue weight.
CAUTION
DO NOT use a bumper mounted hitch on
your vehicle. Use a hitch that is attached to the frame of
your vehicle only. DO NOT compromise your equipment,
your safety or the safety of others.
Wiring
The trailer requires wiring from your vehicle to the trailer lights.
This can usually be done by the hitch company.
Security
There are several locking devices available at marine supply stores
to aid in securing your boat whether or not it is attached to your
vehicle.
10 -7
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 10_2008.qxd:Naut Air Sec 10.qxd 6/24/08 4:12 PM Page 10-8
S e c t io n 10
Towing Your Boat
Read this checklist prior to trailering your boat.
• Check wheel lug nuts for tightness.
• Be sure the trailer tongue is securely on the hitch and the
safety chains from the trailer are secured to the vehicle.
• If your boat is equipped with a trailer bow winch, make sure
the boat is properly located on the trailer and the winch
strap/ cable is tight.
• Be sure a cable or strap secures the bow eye of the boat to
the trailer. Make sure this is tightly secured.
• Be sure the trailer electrical connector is plugged in. Allow
sufficient slack for cornering. Check brake lights, turn
signals, emergency flasher and running lights.
• Be sure your gear inside the boat and seat cushions cannot
shift or fly out of the boat during trailering.
• Be sure the walk-thru door of the windshield is closed and
latched while the boat is being trailered.
• If you are using any sort of water "ballast" system to add
weight to the boat, be sure it is drained before you put the
boat on the trailer. These systems can adversely affect the
tongue weight of the trailer. Your boat is not designed to
carry exceptionally heavy loads. This can adversely effect the
proper balance of the boat/ trailer combination and cause
tire failure and/ or loss of control.
• Make sure the platform bracket pins are in place before
trailering.
• Remove bilge drain plug(s).
Long Trips
DO NOT use your boat and trailer to haul excessive gear.
Each time you stop on a long trip, check the following:
• Make sure the wheel lug nuts are tight and the bearings are
lubricated.
• Make sure the boat is still positioned snugly against the bow
stops and has not shifted.
10 -8
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 10_2008.qxd:Naut Air Sec 10.qxd 6/24/08 4:12 PM Page 10-9
S t o r a g e
• Examine the hitch connection to be sure it is firmly attached
and the safety pin and chains are securely fastened.
• Make sure all trailer lights are still functioning properly.
• Re-examine the contents of your boat to ensure that no
items such as life jackets or other gear have shifted and will
not fly out while you are on the road.
10 -9
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Sec 10_2008.qxd:Naut Air Sec 10.qxd 6/24/08 4:12 PM Page 10-10
S e c t io n 10
N O T E S
10 -10
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Gloss_2008.qxd:Naut Air Gloss.qxd 6/24/08 4:13 PM Page G-1
Glossary
ABYC – American Boat and Yacht Council, Inc.
AFLOAT – On the water.
AFT – Toward the rear or stern of the boat.
AGROUND – Touching bottom.
AMIDSHIP – Center or middle of the boat.
ANCHOR – (1) An iron casting shaped to grip the lake bottom to
hold the boat. (2) The act of setting the anchor.
ANODE – An electrode carrying a positive charge.
ASHORE – On the shore.
ASTERN – Toward the stern.
BAIL – To remove water from the bottom of the boat with a pump,
bucket, sponge, etc.
BALLAST – Any solid or liquid weight placed in a boat to increase
the draft, to change the trim.
BEAM – The widest point on the boat.
BEARING – Relative position or direction of an object from the boat.
BILGE – The lowest interior section of the boat hull.
BOARDING – To enter the boat.
BOUNDARY WATERS – A body of water between two areas of
jurisdiction; i.e., a river between two states.
BOW – The forward end of the boat.
BULKHEAD – Vertical partition (wall) in a boat.
BUNKS – Carpeted trailer hull supports.
BURDENED BOAT – Term for the boat that must "give-way" to boats
with the right-of-way.
CAPACITY PLATE – A plate that provides maximum weight capacity
and engine horsepower rating information. It is located in full view
of the helm.
CAPSIZE – To turn over.
G-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Gloss_2008.qxd:Naut Air Gloss.qxd 6/24/08 4:13 PM Page G-2
CAST-OFF – To unfasten mooring lines in preparation for departure.
CATHODE – An electrode carrying a negative charge.
CAVITATION – A phenomenon in which low pressure within a
liquid allows vapor bubbles to form.
CENTER LINE – A lengthwise imaginary line which runs fore and
aft with the boat’s keel.
CHINE – The point on a boat where the side intersects (meets) the
bottom.
CLEAT – A deck fitting with ears to which lines are fastened.
CONSOLE – Also called helm. The steering wheel area of the boat.
CRANKING BATTERY – The main battery used for engine starting
and electrical circuits.
CURRENT – Water moving in a horizontal direction.
DEADRISE – Transverse angle of the bottom of the hull.
DECK – The open surface on the boat where the passengers walk.
DRAFT – The depth of the boat below the water line, measured
vertically to the lowest part of the hull.
ELECTROLYSIS – The break-up of metals due to the effects of
galvanic corrosion.
FENDER – Devices built into or hung over the sides of a boat to
prevent the boat from rubbing or chafing against other boats or
piers.
FORE – Toward the front or bow of the boat. Opposite of aft.
FREEBOARD –The distance from the waterline to the upper surface
of the side of the deck.
FUEL SENDING UNIT – The electrical device that is mounted on
the outside of a built-in fuel tank and controls the dashboard fuel
gauge.
GIVE-WAY BOAT – (1) Term for the boat that must take whatever
action necessary to keep well clear of the boat with the right-of-way in
meeting or crossing situations. (2) The burdened boat.
GUNWALE – The rail or upper edge of a boat’s side.
HEAD – A marine toilet.
HELM – The steering wheel or command area.
HULL – The structural body of a boat below the deck.
G-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Gloss_2008.qxd:Naut Air Gloss.qxd 6/24/08 4:13 PM Page G-3
Glossary
HYPOTHERMIA – A physical condition where the body loses heat
faster than it can produce it.
IN-LINE FUSE – A type of protective fuse located in the power wire
of a direct current (DC) circuit usually near the battery.
KEEL – The lowest portion of the boat; extends fore and aft along
the boat’s bottom.
LINE – All rope in a boat or on the dock is referred to as “line.”
LIST – Leaning or tilt of a boat toward the side.
MAKING WAY – Making progress through the water.
MARINE CHART – Seagoing maps showing depths, buoys,
navigation aids, etc.
MID SHIP (AMIDSHIP) – In the vicinity of the mid-length of a boat,
technically the exact half way between the bow and the stern.
MOORING – An anchor, chain, or similar device that holds a boat in
one location.
NAVIGATION AID – Recognizable objects on land or sea such as
buoys, towers or lights which are used to fix position to identify safe
and unsafe waters.
NMMA – National Marine Manufacturer’s Association
NO-WAKE SPEED – The speed at which a boat travels to produce an
imperceptible wake.
PFD – Personal flotation device.
PITOT TUBE – See SPEEDOMETER PICKUP TUBE.
PLANING HULL – A hull designed to lift, thereby reducing friction
and increasing efficiency.
PORPOISE – A condition in which the bow bounces up and down
caused by trimming the engine too far out.
PORT – (1) The left side of a boat when facing the bow. (2) A
destination or harbor.
PRIVILEGED BOAT – Term used for the boat with the right-of-way.
PROPELLER PITCH – Theoretical linear distance the propeller
would move ahead during one complete revolution of it were turning
with zero slippage.
RIGHT-OF-WAY – Term for the boat that has priority in meeting or
crossing situations. The stand on or privileged boat.
RUB RAIL – The rubber extrusion that is fastened over the hull and
deck joint.
G-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Gloss_2008.qxd:Naut Air Gloss.qxd 6/24/08 4:13 PM Page G-4
RUDDER – A vertical metal device used to steer the boat
RULES OF THE ROAD – Regulations for preventing collisions on
the water.
SACRIFICIAL ANODE – Metal parts fitted to the hull of boat to
provide a transfer of ions to the cathodic part of an electrolytic
coupling and so protect other parts of the boat that would otherwise
waste away through electrolysis
SLIP – The linear distance between the pitch (or advance) and the
actual distance the propeller moves straight ahead through the water.
SPEEDOMETER PICKUP TUBE – Also called pitot tube. The plastic
device that extends below the bottom of the boat. It connects to the
speedometer with plastic flexible tubing.
SPRING LINE – A mooring rope oriented at a small angle to the
boats centerline, usually attached to the boat mid ship.
STAND ON BOAT – Term for the boat that must maintain course
and speed in meeting or crossing situations. The privileged boat.
STARBOARD – The right side of the boat when looking towards the
bow.
STERN – The aft end of a boat.
STOW –To put away. To store cargo in a storage locker.
STRINGER – Members under the floor that stiffen the hull bottom.
SURGE BRAKES – A type of trailer braking system designed to
automatically actuate when the tow vehicle’s brakes are applied.
TRANSDUCER – The unit that sends/ receives signals for the depth
sounder.
TRANSOM – The transverse beam across the stern.
TRIM – Fore to aft and side to side balance of the boat when loaded.
UNDERWAY – Boat in motion; i.e., not moored or anchored.
USCG – United States Coast Guard
VISUAL DISTRESS SIGNAL – A device used to signal the need for
assistance such as flags, lights and flares.
WAKE – The waves that a boat leaves behind when moving through
the water.
WATERLINE The line of the water’s edge when the boat is afloat.
WATERWAY – A navigable body of water.
WETTED SURFACE – The area of the immersed hull plus
underwater gear.
G-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Warr_2008.qxd:Naut Air Warr.qxd 6/24/08 4:15 PM Page W-1
Warranty
CORRECT CRAFT LIMITED
WARRANTY
(Boats as Originally Manufactured by Correct Craft)
The Correct Craft warranty is backed by a family tradition of boat
building experience since 1925.
Lifetime Limited Warranty:
Correct Craft, Inc. warrants to the original user or purchaser,
whoever comes first, of each new Nautique boat, that the deck,
hull, and stringer system as originally manufactured by Correct
Craft, shall under normal authorized use remain free from
structural defect in material and workmanship.
Transferable Lifetime Limited Warranty:
In addition, Correct Craft offers a Transferable Lifetime Limited
Warranty against structural defect of the deck, hull and stringer
system as detailed in the Lifetime Limited Warranty above. This
policy may be transferred for a nominal fee to the second (2nd)
purchaser during a period of five (5) years from the date of delivery
to the original user or purchaser. See owner’s manual for proper
form.
Exception: The "Lifetime" and "Transferable" warranties do not
cover the gelcoat nor any other components fastened or applied to
the hull or deck. Gelcoat discoloration, blisters, or bubbles and
cracks are not considered structural defects.
W-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Warr_2008.qxd:Naut Air Warr.qxd 6/24/08 4:15 PM Page W-2
Boat Five (5) Year Transferable Limited Warranty:
Correct Craft, Inc. warrants to the original user or purchaser,
whichever comes first, that each new Nautique boat, as originally
manufactured by Correct Craft, shall under normal authorized use
be free of defect in material and workmanship for a period of five
(5) years from the date of delivery. This coverage applies to factory-
installed components including V-drive, boat parts, options, or
other components not manufactured by Correct Craft, Inc. The
remaining portion of this warranty covering PARTS (no labor),
may be transferred for a nominal fee to the second (2nd)
purchaser during a period of five (5) years from the date of
delivery. See owner’s manual for proper form.
Gel Coat Three (3) Year Non-transferable Limited
Warranty:
Correct Craft, Inc. warrants to the original user or purchaser,
whichever comes first, of each new Nautique boat that the gel coat,
under normal authorized use, shall remain free from defect in
material and workmanship (including blisters and cracks not
caused by negligence, impact or collision) for a period of three (3)
years from date of delivery. NOTE: Gelcoat maintenance is the
owner’s responsibility.
Engine Warranty:
For details see Pleasurecraft Marine Engine Co., owner’s manual.
Exceptions: This “Correct Craft Limited Warranty” shall not apply
to…
• Any Nautique boat which has been used at any time for
commercial or racing purposes, as a demonstrator or in a
promotional program, ski school or ski show.
• Normal maintenance of boat, or any component thereof,
including but not limited to alignment, adjustments,
connectors, saltwater/ brackish water corrosion, and wear
items including, but not limited to, non-skid material,
battery, bushings, packing material, bulbs, seals, gaskets.
• Gelcoat finish or colorfastness of gelcoat finish, chrome
plated, anodized or aluminum finish or colorfastness of
finish.
W-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Warr_2008.qxd:Naut Air Warr.qxd 6/24/08 4:15 PM Page W-3
Warranty
• Damage or malfunction of a boat, or any component
thereof, resulting from owner use, lack of maintenance,
improper maintenance, impact, misuse, negligence,
collision, delay of repair (unless specifically and directly
authorized by the Correct Craft warranty department in
writing), trailer or trailer design, improper or inadequate
trailering or cradling of the boat.
• Any addition, modification or repair of the boat, or any
component thereof, caused by, resulting from or in
connection with any party other than Correct Craft, Inc., or
any defect or product failure caused by, resulting from or in
connection with any such addition, modification or repair.
• Any and all consequential damages including, but not limited
to, costs incurred for haul-out, launching, towing, and
storage charges, telephone or rental charges of any type,
inconveniences, or loss of time or income.
Any defect or damage covered by this warranty shall, at the
discretion of Correct Craft, Inc., be repaired free of charge at an
authorized dealership or service facility. Repairs will be warranted
only for the remainder of the original warranty period.
Transportation and/ or labor to and from the point of repair will
be the responsibility of the owner.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND
THE DESCRIPTION OF THE FACE HEREOF. THIS LIMITED
WARRANTY IS EXPRESSLY MADE IN LIEU OF ALL OTHER
EXPRESSED WARRANTIES. DURATION OF ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR OTHERWISE, SHALL BE LIMITED
TO AND COINCIDENT TO THE DURATION OF THESE
EXPRESSED WARRANTIES. UNDER NO CIRCUMSTANCES
SHALL CORRECT CRAFT, INC. BE LIABLE TO THE
PURCHASER OR ANY THIRD PARTY FOR LOSS OF PROFITS
OR OTHER DIRECT OR INDIRECT COSTS, LOSSES OR
CONSEQUENTIAL DAMAGES ARISING OUT OF OR AS A
RESULT OF DEFECTS IN PRODUCTS HEREIN ABOVE
WARRANTED.
W-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Warr_2008.qxd:Naut Air Warr.qxd 6/24/08 4:15 PM Page W-4
Some states do not allow limitations on how long an implied
warranty lasts. Some states do not allow the exclusion or
limitation of incidental or consequential damages. This warranty
gives you specific legal rights, and you also have other rights which
may vary from state to state. To the extent that your state does
not allow any exclusion or limitation expressed herein, such
exclusion or limitation will not apply to you. All other allowable
limitations or exclusions shall apply to you.
Note: This warranty is expressly conditioned upon the
completion and return of the warranty registration card to
Correct Craft, Inc. Although not obligated to and without creating
such an obligation, this will enable us to notify you of any
necessary performance or safety modifications to your boat and to
verify ownership in case a warranty claim is filed on your boat.
Procedure:
In the event your Nautique boat has a claim covered by this
warranty, the following procedure shall be allowed to secure
performance of warranty obligations:
1. Notify the selling dealer in writing within thirty (30) days after
the discovery of any claimed defect.
2. You may be required to transport the boat, at your expense, to
an authorized dealership or service facility for their inspection
and/ or repair.
3. Correct Craft, Inc. reserves the right to require further
evaluation and/ or information regarding a warranty claim
against a boat prior to its repair as well as designate the place
of repair.
Correct Craft, Inc. reserves the right to make changes in prices,
color, specifications, equipment, options, materials, hull, decks,
and/ or discontinue models at any time (without notice), and shall
be under no obligation to equip or modify boats built prior to
such changes.
Correct Craft, Inc., 14700 Aerospace Pkwy, Orlando, Florida
32832. 407/ 855-4141, FAX 407/ 851-7844, E-mail address:
info@nautiques.com. Effective 2006-2009 Model boats.
W-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Warr_2008.qxd:Naut Air Warr.qxd 6/24/08 4:15 PM Page W-5
Warranty
** A COPY OF THE PURCHASE RECEIPT MUST BE INCLUDED **
At Correct Craft, Inc.’s discretion, the remaining portion of the Correct Craft Inc “Boat Five (5) Year
Transferable Limited Warranty” of 2006-2009 model boats, that covers parts (no labor), can be
transferred for $300.00 to the second purchaser within five (5) years from the date of sale to the first
purchaser. The sale must be complete within the first five years. The limited warranty on parts (no
labor) will be transferred upon the receipt and verification of: (1) this completed form, (2) a copy of the
purchase receipt, (3) a payment of $300.00 to "Correct Craft, Inc". This data MUST BE RECEIVED
WITHIN 15 DAYS OF THE SALE DATE. The warranty will be transferred retroactive to the sale
date. Review the warranty policy for details.
NOTE: THIS TRANSFER DOES NOT INCLUDE THE ENGINE.
ORIGINAL OWNER ___________________________________________________
BOAT MODEL/TYPE___________________________________________________
HULL NUMBER / CTC…__________________________________________________
NEW OWNER INFORMATION:
NAME
___________________________________________________
STREET / P.O. BOX_______________________________________________
CITY / STATE / ZIP CODE_________________________________________
DATE PURCHASED
/
/
PHONE NO.
THE CRITERIA LISTED ABOVE MUST BE RECEIVED WITHIN 15 DAYS OF THE SALE
DATE. SUBMIT IT TO CORRECT CRAFT, INC., 14700 AEROSPACE PKWY, ORLANDO,
FLORIDA 32832, "ATTENTION WARRANTY DEPARTMENT."
NOTE: Upon verification, the warranty will transfer retroactive to the sale date
W-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Warr_2008.qxd:Naut Air Warr.qxd 6/24/08 4:15 PM Page W-6
REQUEST FOR WARRANTY TRANSFER OF
HULL, DECK, AND STRINGER
**A COPY OF THE PURCHASE RECEIPT MUST BE INCLUDED **
At Correct Craft, Inc.’s discretion, Correct Craft's Lifetime Limited Warranty against
structural defects in material and workmanship of the hull, deck, and stringer for 2006-2009
model boats can be transferred, for a nominal fee, to the second purchaser within five (5)
years from the date of sale to the first purchaser. The sale must be complete within the first
five years. The limited warranty will be transferred upon the receipt and verification of: (1)
this completed form, (2) a copy of the purchase receipt, (3) a payment of $300.00 to
"Correct Craft, Inc". This data MUST BE RECEIVED WITHIN 15 DAYS OF THE SALE
DATE. The warranty will be transferred retroactive to the sale date. Review the warranty
policy for details.
NOTE: THIS TRANSFER DOES NOT INCLUDE THE ENGINE.
ORIGINAL OWNER ___________________________________________________
BOAT MODEL/TYPE___________________________________________________
HULL NUMBER / CTC…__________________________________________________
NEW OWNER INFORMATION:
NAME
___________________________________________________
STREET / P.O. BOX_______________________________________________
CITY / STATE / ZIP CODE_________________________________________
DATE PURCHASED
/
/
PHONE #____________________
THE CRITERIA LISTED ABOVE MUST BE RECEIVED WITHIN 15 DAYS OF THE
SALE DATE. SUBMIT IT TO CORRECT CRAFT, INC., 14700 AEROSPACE PKWY,
ORLANDO, FLORIDA 32832, "ATTENTION WARRANTY DEPARTMENT."
NOTE: Upon verification, the warranty will transfer retroactive to the sale date
W-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Warr_2008.qxd:Naut Air Warr.qxd 6/24/08 4:15 PM Page W-7
Warranty
NAUTIQUE REGIONAL CENTERS
Correct Craft West
11340 White Rock Rd., Suite A.
Rancho Cordova, CA 95742
916/638-3382
Correct Craft East
P.O. Box 216
Angola, IN 46703
260/833-2226
Southeast Correct Craft
7576 South Orange Ave.
Orlando, FL 32809
407/851-1965
W-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Naut Air Warr_2008.qxd:Naut Air Warr.qxd 6/24/08 4:15 PM Page W-8
If, for any reason your nearest dealer or the warehouse servicing
your territory cannot satisfactorily resolve your problem or answer
your questions, then please feel free to contact our Customer
Service Department at the main offices of Correct Craft, Inc.,
either by telephone or by mail.
14700 Aerospace Parkway, Orlando, Fl 32832
2009 210, 230, 236 only
40)
210, 236
40)
2008 210, 230, 236
Custom Engineered For:
9
(
except 2007 210, 236 & 2008-2009 210, 230, 236
CORC 215
W-8
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Milwaukee Cordless Saw 6509 User Manual
MTD Lawn Mower 111 030 User Manual
Multiquip Saw MP1415E User Manual
NEC Car Video System LCD1860NX User Manual
NEC Computer Monitor FP1375X User Manual
Nextar MP3 Player MA177 User Manual
N Tron Switch 508TX A User Manual
Oregon MP3 Player MP 130 User Manual
Oregon Scientific Weather Radio RMR802 User Manual
Palsonic CRT Television 5160G User Manual