ASSEMBLY AND OPERATING INSTRUCTIONS
MIRAGE 485
OUTDOOR STAINLESS STEEL GAS GRILL
DANGER
NOTICE TO INSTALLER:
IF YOU SMELL GAS:
• Shut off gas to the appliance.
• Extinguish any open flame.
• Open lid.
• If odor continues, keep away from the
appliance and immediately call your
gas supplier or your fire department
LEAVETHESEINSTRUCTIONS
WITHTHEGRILLOWNERFOR
FUTURE REFERENCE
DO NOT TRY TO LIGHT THIS APPLIANCE WITHOUT READING LIGHTING INSTRUCTIONS
SECTION OF THIS MANUAL
NAPOLEONAPPLIANCECORPORATION.,
214 BAYVIEW DR., BARRIE, ONTARIO, CANADA L4N 4Y8 PHONE: (705)726-4278
N415-0156 APR11/07
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
WARNING
WARNING
Do not store or use gasoline or other flam-
mable liquids or vapor in the vicinity of this
or any other appliance. An L.P. cylinder not
connected for use must not be stored in the
vicinity of this or any other appliance. Keep
area clear and free from combustible
Failure to follow these instructions could
result in property damage, personal
injury or death. Read and follow all
warnings and instructions in this manual
prior to operating grill.
WARNING
SAFE OPERATING PRACTICES
DANGER: READ ALL INSTRUCTIONS CAREFULLY BEFORE OPERATING GRILL. FAILURE TO FOLLOW
THESE INSTRUCTIONS EXACTLY COULD RESULT INA FIRE CAUSING SERIOUS INJURY OR DEATH.
•Read the entire instruction manual before operating grill.
•Under no circumstance should this gas grill be modified.
•Follow lighting instructions carefully when operating grill.
•Gas must be turned off at the propane cylinder or at the natural gas supply valve when the gas grill is not in use.
•Keep children and pets away from hot grill, DO NOT allow children to climb inside cabinet.
•Do not leave the grill unattended while in use.
•Do not move grill when hot or operating.
•This gas grill is not intended to be installed in or on recreational vehicles and/or boats.
•This gas grill must only be stored outdoors in a well-ventilated area and must not be used inside a building, garage or any enclosed
area.
•Maintain proper clearance to combustibles (16” to rear of unit 7” to sides). Additional clearance is recommended near vinyl siding or
large panes of glass.
•At all times keep the ventilation openings of the cylinder enclosure free and clear from debris.
•Do not locate unit under unprotected combustible construction.
•Do not locate in windy settings. High winds adversely affect the cooking performance of the gas grill.
•When the gas grill is stored indoors, the propane cylinder must be disconnected from the grill and stored outdoors in a well ventilated
area, disconnected cylinders must not be stored in a building, garage or other enclosed area.
•Inspect the fuel line hose before each use. If there is evidence of excessive abrasion or wear, it must be replaced before using the
gas grill, with a replacement hose assembly specified by the manufacturer.
•Never store a spare LP gas cylinder under or near this grill.
•Never fill the cylinder beyond 80 % full.
•Do not attempt to use a cylinder which is not equipped with a QCC1 type connection.
•Leak test all connection before first use, even if the grill was purchased fully assembled, annually or whenever any gas component
has been replaced.
•Never use natural gas in a unit designed for liquid propane gas.
•Never use charcoal briquets or lighter fluid in a gas grill.
•Burner controls must be off when turning supply cylinder on.
•Do not light burner with lid closed.
•Do not operate rear burner with main burner operating.
•The top lid is to be closed during the preheat period.
•Do not route hose underneath drip pan-proper hose clearance to bottom of unit must be maintained.
•Clean grease tray and sear plates regularly to avoid build-up which may lead to grease fires.
•Ensure sear plates are positioned properly according to sear plate installation instructions.
•Do not use side shelves to store lighter, matches or any other combustibles.
•Keep fuel line away from heated surfaces
•Keep electrical supply cords away from water or heated surfaces.
•Inspect infrared burner venturi tube for spider webs and other obstructions periodically. Clean the tubes
completely if you find any such obstructions.
•The outdoor cooking gas appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of 0.5psi (3.5kPa).
•The outdoor cooking gas appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5 kPa).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
CYLINDER SPECIFICATIONS/GAS HOOK UP
This gas barbecue is certified under Canadian and American national standards, CAN/CSA-1.6-2005 and ANSI Z21.58 -2005
respectively for outdoor gas grills and should be installed to conform with local codes. In absence of local codes, install to the
current CAN/CGA-B149.1 Propane Installation Code in Canada or to the National Fuel Gas Code, NFPA54/ANSI Z223.1 in the
United States.
If a rotisserie motor is used, it must be electrically grounded in accordance with local codes or, in absence of local codes, with
the current CSA C22.1 Canadian electrical code in Canada or the National Electrical Code, ANSI/NFPA 70 in the United States.
CALIFORNIA PROPOSITION 65: The burning of gas fuel creates by products, some of which are on the list as substances
known by the State of California to cause cancer or reproductive harm. When cooking with gas, always ensure adequate
ventilation to the unit, to minimize exposure to such substances.
PROPANE CYLINDER SPECIFICATIONS: A dented or rusty cylinder may be hazardous and should be checked by your propane
supplier. Never use a cylinder with a damaged valve. Use only a propane supply cylinder constructed and marked in accordance
with the specifications for LP-gas cylinders of the Canadian Transport Commission (CTC) or the US Department of Transportation
(DOT). This appliance has been designed for use with a 20lb. (9.1 kg) size propane cylinder only (not supplied).
The propane cylinder must be provided with a shut-off valve terminating in a propane cylinder valve type QCC1, and a safety relief
device having direct communication with the vapour space of the cylinder. The cylinder supply system must be arranged for vapour
withdrawal and the cylinder shall include a collar to protect the cylinder valve. The cylinder shall incorporate an OPD (overfill
protection device).
CYLINDER CONNECTION: Ensure that the gas regulator hose is kink free. Remove the cap or plug from the cylinder fuel valve.
Insert the black QCC1 regulator nipple onto the QCC1 fuel valve. Hand tighten clockwise. Do not use tools. Leak test all joints
prior to using the barbecue. A leak test must be performed annually, and each time a cylinder is hooked up, or if a part of the gas
system is replaced.
PROPANE CYLINDER INSTALLATION:
Check that the cylinder valve is closed by turning the knob clockwise.
Check that the grills burner knobs are in the off position.
Open Cabinet doors.
Place the cylinder into the tank holder in bottom of shelf.
Position the cylinder so that the valve faces toward the front of the unit.
Attach regulator hose.
IMPORTANT: Use only the pressure regulator and hose assembly provided with this barbecue. Replacement pressure
regulators and hose assemblies must be specified by the manufacturer. Do not store propane cylinder or spare cylinder on the
shelf beneath the barbecue The regulator must be attached so that no part of the hose touches the underside of the grill or
drippan. A fire will result if these directions are ignored.
The regulator supplies a pressure of 11 inches water column to the gas grill and has a QCC1 type fitting. Cylinders to be used
with this unit must be supplied with a Sherwood #3349 QCC1 cylinder valve. A QCC1 cylinder has a positive seating connection,
which will not allow gas flow until a positive seal has been achieved. It is also equipped with an excess flow device. In order to
attain full flow to the barbecue, the valves must be in the off position when the cylinder valve is turned on.
NATURAL GAS HOOK-UP: This natural gas grill is supplied with a 10ft supply hose (complete with a quick disconnect)
designed for natural gas and certified for outdoor use. The gas grill is designed to operate at an inlet pressure of 7 inches water
column. Piping and valves upstream of the quick disconnect are not supplied.
The quick disconnect must not be installed in an upward direction and a readily accessible manual shut-off valve must be
installed upstream of, and as close to, the quick disconnect as is feasible. The flared end of the hose must be connected to the
fitting on the end of the flex tube as illustrated in the Natural Gas Hose Attachment diagram. Tighten using two wrenches. (Do
not use thread sealer/pipe dope.) These connections must be made by a licensed gas installer. Leak test all joints prior to
using the gas grill.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
LIGHTING INSTRUCTIONS
OPEN LID.
ENSURING BURNER CONTROLS
ARE IN THE OFF POSITION, TURN
ON THE GAS SUPPLY VALVE.
RIGHT BURNER
SIDE BURNER
CENTER BURNER
LEFT BURNER
MAIN BURNER LIGHTING
SIDE BURNER LIGHTING
1. OPEN SIDE BURNER
COVER.
1. PUSH AND TURNANY MAIN
BURNER KNOB SLOWLYTO
THE ’HI’POSTION. THISACTION
WILL IGNITE THE PILOT FLAME
WHICH WILL IN TURN LIGHT THE
SELECTED BURNER. IF THE
PILOT LIGHTS, CONTINUE TO
PUSH DOWN ON THE CONTROL
KNOB UNTIL THE BURNER
2. PUSHAND TURNTHE
SIDE BURNER CONTROL
KNOB SLOWLY TO THE
‘HI’ POSITION. THIS
ACTION WILL IGNITE
THE SIDE BURNER
LIGHTSANDTHEN RELEASE.
3. IF THE BURNER DOES NOT
IGNITE,THEN IMMEDIATELY
TURN THE CONTROL KNOB
BACK TO THE ‘OFF’ POSITION
AND REPEAT STEP 2 SEVERAL
TIMES.
2. IF THE PILOT DOES NOT
IGNITE,THEN IMMEDIATELY
TURN THE CONTROL KNOB
BACK TO THE ‘OFF POSITION
AND REPEAT STEP 1 SEVERAL
TIMES.
4. IF THE BURNER WILL NOT IGNITE
WITHIN 5 SECONDS, TURN THE
CONTROL KNOB TO THE ‘OFF’
POSITIONAND WAIT5 MINUTES
FOR ANY EXCESS GAS TO
3. IF THE PILOTAND BURNER WILL
NOT IGNITE WITHIN 5 SECONDS,
TURN THE CONTROL KNOB TO THE
‘OFF’POSITIONAND WAIT 5
MINUTES FORANY EXCESS GAS TO
DISSIPATE. EITHER REPEAT STEPS 1
AND 2 OR LIGHT WITHAMATCH.
DISSIPATE. EITHER REPEATSTEPS
2AND 3 OR LIGHT WITHAMATCH.
The propane cylinder is equipped with an excess flow device. Unless all burners are
turned off prior to turning the cylinder on, only small flames will be achievable.
If lighting the unit with a match, clip the match into the supplied lighting rod. Hold the
lit match down through the grill and sear plate while turning the corresponding burner
valve to high.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE GRILL
BURN IN PROCEDURE
When lit for the first time, the gas grill will emit a slight odour. This is a normal temporary condition caused by the "burn-in" of
internal paints and lubricants used in the manufacturing process and will not occur again. Simply run the main burners on high
for approximately ½ hour with the lid closed.
MAIN BURNER USE:
When searing foods, preheating is recommended by operating all main burners in the high position with the lid closed for
approximately 15 minutes. Food cooked for a short period of time (fish, vegetables) may be grilled with the lid open. Cooking with
the lid closed will ensure higher, more even temperatures that will reduce cooking time and cook meat more evenly. When
cooking very lean meats, such as chicken breasts, or lean pork, the grids can be oiled before pre-heating to reduce sticking.
Cooking meat with a high degree of fat content, may create flare-ups. Either trim some fat or reduce temperatures to prevent this.
Should a flare-up occur, move food away from flames, reduce heat. Leave the lid open. See 'Your All Season Grill' cookbook by
Napoleon for more detailed instructions.
DIRECT COOKING:
Place food to be cooked on the grill directly over the heat. This method is generally used for searing or for foods that do not
require prolonged cooking times - hamburgers, steaks, chicken pieces, vegetables, etc. The food is first seared to trap in the
juices and flavor, and then the temperature is lowered to finish cooking the food to your preference.
INDIRECT COOKING:
With one or more burners operating place food to be cooked on the grill over one of the burners that is not operating. The heat
circulates around the food, cooking slowly and evenly. Cooking in this manner is much the same as cooking in your oven and is
generally used for larger cuts of meats such as roasts, chickens or turkeys, but can also be used for cooking foods that are prone
to flare ups. Cooking in this method with lower temperatures and slower cooking times will result in tender foods every time you
grill.
INFRARED MAIN BURNER USE: (optional)
1. Operate on high for 5 minutes with the lid closed or until the ceramic burners glow red.
2. Place food on grills, searing in juices approximately 2 minutes per side.
3. Depending upon your taste, continue cooking over infrared burner on high, medium or low, turning food frequently, or place
food away from infrared burners, close lid, and allow oven temperature to slowly finish cooking your food.
PROTECTION OF YOUR INFRA RED BURNERS - The infrared burners of your grill are designed to provide a long
service life. However, there are steps you must take to prevent cracking of their ceramic surfaces, which will cause the
burners to malfunction.
1. Never let water come in direct contact with your ceramic burner.
2. Avoid impact with hard objects.
3. In order for the burners to function properly, hot air must have a way to escape the grill. If the hot air is not allowed to
escape, the burners may become deprived of oxygen, causing them to crack. Do not cover more than 75% of the cooking
surface with solid metal (ie. griddle or large pan).
Damage caused by failure to follow these steps is not covered by your grill warranty.
IMPORTANT
•
Do not allow cold water (rain, sprinkler, hose, etc.) to come in contact with hot ceramic burners. A large
temperature differential can cause cracking of the ceramic tile.
SIDE BURNER USE:
The side burner can be used like any range top burner, for gravies, soups etc. The gas grill should be located so that the side
burner is protected from the wind, because the wind will adversely affect it’s performance. DO NOT use side burner to deep fry
foods as cooking with oil can create a dangerous situation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE/CLEANING INSTRUCTIONS
It is recommended that this gas grill be thoroughly inspected and serviced annually by a
qualified service person.
•
Do not use pressure washer to clean any part of the unit.
Ensure that the burners are turned off prior to cleaning. Avoid unprotected contact with hot surfaces. Clean grill in an
area where cleaning solutions will not harm decks, lawns or patios. Do not use oven cleaner to clean any part of this gas
grill. Do not use a self cleaning oven to clean cooking grids or any other parts of the gas grill. Barbecue sauce and salt
can be corrosive and will cause rapid deterioration of the gas grill components unless cleaned regularly.
Turn off the gas at the source and disconnect unit before servicing. Maintenance should only be done when the grill is
cool, to avoid the possibility of burns. A leak test must be performed annually, and whenever any component of the gas
train is replaced.
COMBUSTION AIR ADJUSTMENT - (This must be done by a qualified gas installer.) The air shutter is factory set and
should not have to be adjusted under normal conditions. However, some extreme field conditions may exist that require
adjustment. When the air shutter is adjusted correctly, the flames will be dark blue with light blue tips, and occasional yellow
tips.
If the burner is getting too little air, the flames will be lazy yellow, and possibly produce soot. If the burner is getting too
much air, the flames will be lifting erratically from the burner and may cause difficulties when lighting.
1. To adjust the air shutter, remove cooking grids and sear plates and leave lid open. The back cover must be removed for
back burner air shutter adjustment.
2. Loosen air-shutter lock screw and open or close air shutter as required. The normal settings are:
Main Burner
Propane
Natural
5/32"
5/32"
3. Light burners and set to high. Visually inspect burner flames. When shutters are set, turn burners off, tighten locking
screw, and replace removed parts. Ensure that the insect screens are installed.
BURNER
LIGHT BLUE
BURNER PORT
YELLOW TIPPING
APPROXIMATELY
1/2"
DARK BLUE
GRIDS AND WARMING RACK - The grids and warming rack are best cleaned during the pre-heat period with a soft brass
wire brush. Steel wool can be used for stubborn stains. Stainless grids will discolour permanently from normal usage, due
to the high temperature of the cooking surface.
CLEANING INSIDE THE GAS GRILL - Remove cooking grids. Use a soft brass wire brush to clean loose debris from casting
sides and insides of the lid. Scrape sear plates with a putty knife or scraper, and use a wire brush to remove ash. Remove
sear plates and brush debris off of burners with a brass wire brush. Brush all debris from inside the gas grill into the
removable drip pan. Ensure that the sear plates are placed properly when they are reinstalled (Check assembly instructions
for proper orientation).
DRIP PAN - Slide the drip pan out for easy cleaning. It should be cleaned frequently (every 4-5 uses) to avoid grease
buildup. Grease and excess drippings pass through to the drip pan, located under the gas grill, and accumulate in the
disposable grease tray below the drip pan. Accumulated grease can cause a fire hazard. Do not line the drip pan with
aluminum foil or sand, as it can prevent the grease from flowing properly. The pan should be scraped out with a putty knife or
scraper, and all the debris should be scraped into the disposable grease tray. This tray should be replaced every two to four
weeks, depending on gas grill usage. For supplies, see your Napoleon Gas Grill dealer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE/CLEANING INSTRUCTIONS
HOSE - Check for abrasion, melting, cuts and cracks. If any of these conditions exist, do not use gas grill. Have part
replaced by your Napoleon Gas Grill dealer, or qualified gas installer.
CLEANING THE OUTSIDE OF THE GAS GRILL - Do not use abrasive cleaners to clean any painted, porcelain or stainless
steel parts. Porcelain enamel components must be handled with additional care. The baked on enamel finish is glass like,
and will chip if struck. Touch-up enamel is available from your Napoleon Gas Grill dealer. Exterior grill surfaces should be
cleaned while warm to the touch, with warm soapy water. To clean stainless surfaces, use a stainless steel cleaner or a non-
abrasive cleaner. Always wipe in the direction of the grain. Do not use steel wool, as it will scratch the finish. Stainless steel
parts will discolour when heated, usually to a golden or brown colour. This discolouration is normal and will not affect the
performance of the grill.
TUBE BURNER - The burner is made from heavy wall 304 stainless steel, but due to the extreme heat and corrosive
environment, surface corrosion will occur. Use a brass wire brush to remove surface corrosion. Clean any blocked ports
using an opened paper clip. Do not enlarge the burner ports. Spiders and insects are attracted to the smell of propane and
natural gas. The burner is equipped with an insect screen on the air shutter, which will reduce the likelihood of insects
building nests inside the burner, but does not entirely eliminate the problem. The nest or web will cause the burner to burn
with a soft yellow or orange flame or cause a fire (flashback) at the air shutter underneath the control panel. To clean the
inside of the burner, it must be removed from the gas grill. Remove the screw located in the center of each burner. Lift the
back of the burner upwards to remove. Use a flexible venturi tube cleaning brush to clean out the inside of the burner. Shake
any loose debris out of the burner, through the gas inlet. Ensure that the insect screen is clean, tight, and free of any lint or
other debris. Check also that the valve orifices are clean. Do not enlarge the orifices. Re-install the burner.
CAUTION BEWARE OF SPIDERS
WARNING
It is very important when re-installing the burner after
cleaning that the valve/orifice enters the burner tube before
lighting your gas grill. If the valve is not inside the burner
tube a fire or explosion could occur.
INFRA RED BURNER - Because of the high intensity of the infrared burner, most drippings and food particles that fall onto the
burner surface are immediately incinerated. However, some debris and residue may remain. To remove this residue after
cooking, turn the grill on high with lid closed for 5-10 minutes. Never use a brush or pressure washer to clean the infra red
burners.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Possible Causes
Solution
Low heat / Low flame when
valve turned to high.
For propane - improper lighting
procedure.
Ensure lighting procedure is followed carefully. All gas grill
valves must be in the off position when the tank valve is
turned on. Turn tank on slowly to allow pressure to
equalize. See lighting instructions.
For natural gas - undersized
supply line.
Pipe must be sized according to installation code.
For both gases - improper
preheating.
Pre-heat grill with both main burners on high for 10 to 15
minutes.
Ensure sear plates are installed with the holes towards the
front, and the slots on the bottom. See assembly
instructions.
Excessive flare-ups/uneven
heat.
Sear plates installed incorrectly.
Improper pre-heating.
Pre-heat grill with both main burners on high for 10 to 15
minutes.
Excessive grease and ash build
up on sear plates and in drip
pan.
Clean sear plates and drip pan regularly. Do not line pan
with aluminum foil. Refer to cleaning instructions.
Burners burn with yellow
flame, accompanied by the
smell of gas.
Possible spider web or other
debris, or improper air shutter
adjustment.
Thoroughly clean burner by removing. See general
maintenance instructions. Open air shutter slightly
according to combustion air adjustment instructions.
Close air shutter slightly according to combustion air
adjustment instructions.
Improper air shutter adjustment.
Flames lift away from
burner, accompanied by the
smell of gas, and possibly
difficulties in lighting.
This is not a defect. It is caused by internal vibrations in the
regulator, and does not affect the performance or safety of
the gas grill. Humming regulators will not be replaced.
Regulator ‘Hums’ when
unit is operating.
Normal occurence on hot days.
Plugged ports at back of burner.
Burners will not crosslight
each other.
Clean burner ports. See burner maintenance instructions.
"Paint" appears to be
peeling inside lid or hood.
Grease build up on inside
surfaces.
This is not a defect. The finish on the lid and hood is
stainless steel, and will not peel. The peeling is caused
by hardened grease, which dries into paint-like shards,
that will flake off. Regular cleaning will prevent this. See
cleaning instructions.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
WARRANTY INFORMATION
KEEP YOUR RECEIPT AS
PROOF OF PURCHASE
TO VALIDATE YOUR
WARRANTY
MODEL:
DATE OF PURCHASE:
SERIAL NUMBER:
(record information here for easy reference)
Before contacting the customer service department, check the NAC web site for more extensive cleaning, maintenance,
troubleshooting and part replacement instructions at www.napoleongrills.com. Contact the factory directly for replacement parts
and warranty claims. The customer service department is available between 9 AM and 5 PM (Eastern standard time) at 1-866-
820-8686 or fax at 1-705-727-4282. In order to process a claim, we must be provided with the following information:
1. Model and serial number of the unit.
2. Part number and description.
3. A concise description of the problem ('broken' is not sufficient).
4. Proof of purchase (photocopy of the invoice).
In some cases the customer service representative may request to have the parts returned to the factory for inspection, before
providing replacement parts. The parts must be shipped prepaid to the attention of the customer service department with the
following information:
1. Model and serial number of the unit.
2. A concise description of the problem ('broken' is not sufficient).
3. Proof of purchase (photocopy of the invoice).
4. Return Authorization number - provided by the customer service representative.
Before contacting customer service, kindly note that the following items are not covered by the warranty:
-costs for transportation, brokerage or export duties
-labor costs for removal and re-installation
-costs for service calls to diagnose problems
-discoloration of stainless steel parts
-part failure due to lack of cleaning and maintenance, or use of improper cleaners (ovencleaner).
NAPOLEON APPLIANCE CORPORATION
ACCESSORIES / PARTS ORDER FORM
FAX TO: 1-705-727-4282
PLEASE PRINT CLEARLY
CUSTOMER NAME:
ADDRESS:
DATE:
MODEL #:
SERIAL #:
TELEPHONE:
VISA OR MASTERCARD #:
EXPIRY DATE:
DESCRIPTION
PRODUCT NUMBER
QUANTITY
TAXES & SHIPPING CHARGES MAYAPPLY
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
CAUTION: During unpacking and assembly it is recommended that you wear work gloves
and safety glasses for your protection. Although we make every effort to make the assembly
process as problem free and safe as possible, it is characteristic of fabricated steel parts that the
edges and corners may be sharp and can cause cuts if handled incorrectly during assembly.
GETTING STARTED
1. Remove all cart panels, hardware, and grill head from carton. Raise lid and remove any components
packed inside. Use the parts list to ensure all necessary parts are included.
2. Do not destroy packaging until grill has been fully assembled and operating to your satisfaction.
3. Assemble BBQ where it is to be used, lay down cardboard or a towel to protect parts from being
lost or damaged while assembling.
4. Most stainless steel parts are supplied with a protective plastic coating that must be removed prior
to using grill.
5. Follow all instructions in the order that they are layed out in this manual.
6. Two people are required to lift the grill head onto the assembled cart.
TOOLS REQUIRED FOR ASSEMBLY (tools not included)
7/16 WRENCH
OR RATCHET
3/8(10mm)
WRENCH
FLATAND PHILIPS
SCREWDRIVERS
HAMMER
OR RATCHET
If you have any questions about assembly or grill operation, or if there are
damaged or missing parts please call our customer service department at 1-
866-820-8686 between 9 AM and 5 PM (eastern standard time)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
1 x N430-0002
MAGNET CATCH
1
Magnet Installation
Snap magnet into slot in front of bottom shelf.
16 X
16 X
N570-0073 (1/4-20 X 3/8”)
N450-0027 (1/4-20)
Caster/Bracket Installation
2
Attach (4) casters, using (4) 1/4 - 20 X 3/8” screws and (4) 1/4-20 lock nuts
for each caster. Attach brackets under front casters as illustrated. Tighten
securely.
non revolving caster- left side
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PROPANE ONLY
3
Propane Tank Ring Installation
Insert propane tank ring into slots in bottom shelf as shown. Fold tabs over to
secure in place.
4 X
N570-0080 (#14 X 1/2")
4
Left and Right Cart Panel Installation
Install end cart panels ensuring slots in panel are to the top, rest panel on bottom
shelf and line up holes. Fasten using (4) #14 x 1/2” screws.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
6 X
N570-0080 (#14 X 1/2")
5
Rear Cart Panel Installation
Fit rear cart panel between the two end panels, ensure large hole in panel is to
the bottom right hand corner as illustrated. Fasten using (6) #14 x 1/2” screws,
three on each side.
Condiment Basket / Propane Tank Mount Installation
6
Rotate basket slightly to allow wire to enter the holes in the side panel. Push
through and upwards, rotating to allow the bend in the wire to pass through the
holes. Lay basket flat against the side panel. Clip top propane tank mount into
slots in back panel. Insert one end at a time, gently bending wire. (When not
in use tank mount will lay flat against back panel).
PROPANE ONLY
14
Download from Www.Somanuals.com. All Manuals Search And Download.
6 X
1 x N430-0002
MAGNET CATCH
N570-0080 (#14 X 1/2")
Front Cabinet Support Installation
7
Fasten top rail assembly to the front of side panels using (4) #14 x 1/2” screws.
For ease of installation start all screws before tightening completely. Attach
magnet bracket to bottom of top rail using (2) #14 x 1/2” screws, and snap mag-
net into place as shown.
2 X
PROPANE ONLY
N570-0080 (#14 X 1/2")
8
Propane Tank Heat Shield Installation
Attach propane tank heat shield above propane tank ring. Attach one end un-
der lip of back panel and other end to underside of front cabinet support.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
6 x
N570-0073 (1/4-20 x 3/8”)
Grill Head Installation
9
PROPANE ONLY - To avoid assembly difficulties, prior to mounting the grill
head, remove zip tie holding regulator up under control panel. This was installed
at the factory to protect the regulator hose during shipping and is no longer re-
quired. (Take care when removing the tie not to damage the hose).
Lift grill head and place on assembled cart, lining up holes in top of side cart
panels with holes in bottom of base. Fasten from inside using (4)1/4-20 x 3/
8”screws, two per side. Install battery pack below vent slots on left hand panel
using double sided tape supplied with battery pack. Plug wire from LED (lights)
located underneath control panel into wire from battery pack. Install rotisserie
mount bracket to left side of barbecue as shown using (2) 1/4-20 x 3/8” screws.
TWO PEOPLE ARE REQUIRED
FOR THIS STEP
16
Download from Www.Somanuals.com. All Manuals Search And Download.
10 x
N570-0073 (1/4-20 x 3/8")
Assembling End Caps to Side Shelf / Side Burner
10
Peel protective coating from side shelf / side burner. Attach corresponding end
cap as shown using (5) (1/4-20 x 3/8”) screws.
Bend tabs on front of shelf up with a flat head
screw driver, insert screw through tab and into
end cap.
4 X
4 X
N735-0001 (1 1/16” insulated washer)
N570-0082 (1/4-20 x 5/8")
Side Shelf Installation
11
Insert (4) 1/4-20 x 5/8” screws through washers into threaded holes in side of
base, do not tighten all the way. Slide assembled side shelf over screw heads
and finish tightening.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
1 X
4 X
4 X
N160-0016
N735-0001 (1 1/16” insulated washer)
N570-0082 (1/4-20 X 5/8")
12
Side Burner Installation
Insert (4)1/4-20 x 5/8” screws through washers into threaded holes in side of base.
Do not tighten all the way. Slide assembled side burner over screw heads and
finish tightening. Attach 1/2” flex connector hose from manifold to fitting on end of
side burner hose. Fit orifice into burner tube and secure with hose retainer clip
supplied. Attach wire from manifold to side burner electrode.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4 X N735-0003
(1/4” LOCK WASHER)
2 x N105-0011
DOOR BUSHING
4 x N570-0073
(1/4-20 X 3/8")
3/8
Cabinet Door Installation
13
Install door handle onto front of door using (2) 1/4-20 x 3/8” screws and (2) 1/4”
lock washers per door.
Insert pivot rod through hole on inside top of door. Holding door in one hand,
direct pivot rod into hole in underside of front cabinet support. Once secure, let
rod slide down and through hole in bottom of door and into bushing in bottom
shelf.
BUSHING
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3 X N305-0057
14
Sear Plate Installation
Insert sear plates into base, position one over each tube burner with slots down
to allow drippings to travel through.
1 X N520-0023
2 X N305-0058
15
Grill and Warming Rack Installation
Postion grills and warming rack into base as shown. Rest warming rack on
brackets inside hood and grills on front and back lip of base.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Grease Tray and Holder Installation
Clip the wire grease tray holder into the two holes located in the center of the
back panel. Place the aluminum grease tray into the grease tray holder
17
Drip Pan Installation
Slide drip pan into rear of base as shown. Ensure drip pan rides along rails on
bottom of base.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PROPANE ONLY
CLIP HOSE TO SIDE PANEL USING
HOSE RETAINER CLIP SUPPLIED
NATURAL GAS ONLY
2 X
1xN105-0002
INSTALL BUSHING INTO
BACK PANEL
CLIP HOSE TO SIDE PANEL USING HOSE
RETAINER CLIP SUPPLIED
THIS MUST BE PERFORMED BY A LICENSED GAS FITTER.
DO NOT USE PIPE DOPE OR TEFLON TAPE ON THIS CONNECTION
22
Download from Www.Somanuals.com. All Manuals Search And Download.
LEAK TESTING INSTRUCTIONS
DO NOT USE A FLAME TO LEAK TEST.
LEAK TESTING: This must be done before initial use, annually and whenever any gas components are replaced or serviced. No
smoking while performing this test, and remove all sources of ignition. See Leak Testing Diagram for areas to check.
1. Turn all burner controls to off. Turn supply valve on.
2. Brush a half and half solution of liquid soap and water onto all joints and connections of the regulator, hose, manifolds and
valves.
3. Bubbles will indicate a gas leak. Either tighten the loose joint or replace the part with one recommended by the dealer.
4. If the leak cannot be stopped, shut off the gas supply, disconnect it and have the barbecue inspected by your gas supplier or
dealer. Do not use the appliance until the leak has been corrected.
5. Turn off gas supply.
ALEAK TEST MUST BE PERFORMED AT THE
FOLLOWING TIMES:
•BEFORE INITIAL USE EVEN IF THE GRILL WAS
DEALER ASSEMBLED.
•AT LEAST ONCE PER YEAR.
•WHENEVER ANY GAS COMPONENT HAS BEEN
REPLACED.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Item
1
2
3
4
5
6
7
8
Part #
Description
485
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
p
n
p
N135-0024K left side lid casting
N385-0129 NAPOLEON logo
W450-0005 logo spring clips
N510-0010
N685-0003
N051-0004
N335-0042
N585-0040
N010-0504
black silicone lid bumper
temperature gauge
temperature gauge bezel
stainless steel lid insert
heat shield lid
9
lid handle
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
N135-0025K right side lid casting
N570-0015
N010-0502
N570-0008
N570-0073
N735-0003
N520-0023
N305-0058
N305-0057
N010-0529
N120-0009
N570-0082
N010-0528
N120-0008
lid pivot screw
hood assembly
#8 x 1/2" screw
1/4-20 x 3/8" screw
1/4" lockw asher
w arming rack
cooking grids - stainless rod
sear plate
stainless steel side shelf - right
LUXIDIO side shelf end cap, right
1/4-20 x 5/8" screw
stainless steel side shelf - left
LUXIDIO side shelf end cap, left
N500-0035K side burner plate
N100-0037
N335-0043
N305-0059
N555-0019
N100-0036
N080-0202
N475-0199
N010-0500
N010-0501
N160-0014
62007
side burner
side burner lid
side burner grate
side burner lid pivot rod
main burner
main burner cross light bracket
rotisserie mount
base
drip pan
grease tray holder
replacement grease trays (5 pieces)
N200-0077P back cover
N475-0181
N380-0011
N051-0003
N530-0003
N345-0001
N010-0507
control panel
control knob
control knob bezel
1-outlet regulator
10ft n/g hose c/w quick disconnect
manifold assembly c/w valves
41
x - standard
x - compris
p - propane units only
n - natural gas units only
ac - accessory
p - appareils propane seulement
n - appareils gaz naturel seulement
ac - accessoires
24
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Item
Part #
Description
485
n
x
N010-0508
N720-0044
N255-0027
N725-0034
N725-0035
N725-0032
N725-0033
N455-0049
N455-0050
N720-0055
manifold assembly c/w valves
manifold flex connector
union fitting 3/8" - 3/8"
main burner valve c/w #56 orifice
main burner valve c/w #52 orifice
side burner valve
42
43
44
x
p
n
p
n
p
n
x
45
side burner valve
side burner orifice #62
side burner orifice #54
side burner supply tube
47
48
49
50
N475-0183P left/right side panel cabinet enclosure
x
x
x
x
N555-0018
N010-0506
N325-0048
N570-0073
door pivot rod
cart door assembly
door handle
door handle screw s
x
52
53
54
55
56
57
58
59
N590-0147P bottom shelf
x
x
x
p
x
x
p
x
x
x
N010-0505
front cabinet support
N475-0184P rear cart panel
N585-0041P heat shield
N105-0002
N105-0011
snap bushing
door bushings
N655-0094P tank ring support
N430-0002
N020-0122
N750-0020
N190-0001
magnetic catch
main assembly baggie
w iring harness led,
battery pack
61
62
x
W043-0002 battery "AA'
x
64
N735-0001
N105-0001
N640-0001
N160-0015
N130-0012
N450-0027
N080-0212
N590-0164
N130-0013
N370-0454
N555-0020
63485
insulated w asher
bushing 7/8"
x
x
x
p
x
x
x
x
x
ac
ac
ac
ac
ac
66
67
68
69
70
71
72
hose retainer clip
propane tank clip
revolving caster
locking nut 1/4-20
stabilizer brackets
condiment basket
non revolving caster
rotisserie kit
rotisserie spit
vinyl cover
stainless steel griddle
charcoal tray
56017
67730
x - standard
x - compris
p - propane units only
n - natural gas units only
ac - accessory
p - appareils propane seulement
n - appareils gaz naturel seulement
ac - accessoires
25
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
27
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
28
Download from Www.Somanuals.com. All Manuals Search And Download.
|