NEC DVD Player 16x User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.  
Welcome  
Thank you for purchasing the NEC 16x DVD R/RW DL  
drive. Please remove your service tag sticker found on the  
outer carton’s label. This label contains your drive’s service  
tag number and model number and can be placed in the  
space below or can be affixed to the outer cover of your PC.  
You will need this information for product registration and to  
obtain technical support service. To register this product  
Save the box that your drive was shipped in, as NEC can not  
be held accountable for damages caused by shipping in the  
case of a returned product.  
Service Tag Number: _______________________  
Purchase Date: ____________________________  
FCC NOTICE  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses, and can radiate  
radio frequency energy, and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications.  
However, there is no guarantee interference will not occur in a particular  
installation. If this equipment causes harmful interference to radio or  
television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or  
more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications of this device must be approved by the party  
responsible for FCC compliance, or the user loses authority to operate  
this product.  
LASER WARNING  
Visible and invisible laser radiation. Do not open optical housing. Avoid  
direct exposure to the beam.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
Hardware System  
Requirements  
Minimum  
Intel® Pentium® III 800 MHz.  
256 MB memory.  
Used for such things as data backup.  
Recommended  
Intel Pentium 4 1.0 GHz.  
512 MB memory.  
Highly recommended for all DVD recording.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Drive Installation  
! Shut down your computer and disconnect all cables  
plugged into the computer. [Fig. 1]  
@ Remove the computer’s case (refer to your computer’s  
documentation).  
# Once the cover is removed, touch a non-painted metal  
surface (i.e. the power supply) to ground yourself. This is  
an important step! You can damage the components  
inside the computer if you do not ground yourself.  
Fig. 1  
$ If you are replacing an existing drive:  
Unplug the cables from the rear of the drive. [Fig. 2]  
Remove the mounting hardware holding the drive in place  
(refer to your computer’s documentation).  
Slide the drive out through the front of the computer. [Fig. 3]  
Fig. 2  
% If you are NOT replacing an existing drive (i.e. adding an  
additional drive):  
Remove the front cover plate from the empty drive bay  
where you are installing the drive (refer to your computer’s  
documentation).  
^ Check the jumper settings on the NEC DVD drive:  
If you are replacing an existing drive, set the jumper to the  
same setting as the drive you are replacing. The jumper is  
the black plastic piece on the back of your drive bridging  
two of the six pins as seen below [Fig 4]. You may need  
small needle nose pliers to gently slide the jumper off.  
Fig. 3  
Fig. 4  
If you are installing the DVD drive as an additional drive,  
you will need to set the jumper settings according to your  
system requirements (see next page).  
jumper  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Jumper Setting Tutorial:  
There are three possible jumper settings: MASTER, SLAVE,  
and CABLE SELECT (CSEL). When two drives are connected  
to the same interface cable, one must be set to MASTER, and  
one set to SLAVE. Alternatively, both drives may be set to  
CABLE SELECT, in which case the system defines which  
drive is MASTER and which drive is SLAVE. If only one drive  
is present, set the jumper to MASTER. The NEC drive ships  
with a default setting of MASTER.  
If you are installing the DVD drive as a second drive, look at  
the jumper settings on the second drive (already in your  
system). If the settings on that drive are set to MASTER or  
SLAVE, set the jumper to the opposite setting. If the existing  
drive is set to CABLE SELECT (CSEL), set the jumper on the  
NEC DVD drive to CSEL also.  
& Slide the NEC DVD drive into the empty drive bay, from  
the front of the computer. [Fig 5]  
* Mount the drive to your computer’s chassis using the  
existing mounting hardware, or the provided screws (refer  
to your computer’s documentation).  
( Connect the interface cable, making sure the red stripe  
matches Pin 1 on the drive. If your drive is set to  
MASTER, connect it to the endmost connector on the  
cable. [Fig. 6]  
) Connect your computer’s analog audio cable from the  
drive’s audio connector to your sound card (not applicable  
for Windows XP users or those using digital audio  
playback). [Fig. 7]  
Fig. 5  
1 Connect the power cable. [Fig. 7]  
2 Replace the computer’s cover and re-connect all cables  
Fig. 6  
that were previously unplugged.  
3 Power-up the computer.  
Fig. 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Using Your Drive  
Disc Tray  
Busy  
Indicator LED  
Forced Eject  
Hole  
Eject Button  
Busy Indicator LED: Lights up when reading or writing data.  
Eject Button: Press to load or unload a disc.  
Disc Tray: Open or close by pressing the eject button. Load  
discs into the tray with the label side facing up.  
Forced Eject Hole: If the eject button will not open the tray,  
insert a stiff rod such as a large paper clip into the hole  
and push in to eject the tray after the drive has been turned  
off and the disc has stopped spinning.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
About DVD Media Types  
Media compatibility  
Disc Types  
NEC Supports  
DVD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Read  
DVD-Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Read  
DVD+R (SL, DL) . . . . . . . . . . . . . . . . . . . . . . . . . . .Read/Write  
DVD+RW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Read/Write  
DVD-R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Read/Write  
DVD-RW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Read/Write  
DVD-RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . .Not Supported  
SL- Single Layer  
DL- Double Layer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Product Specifications  
Read Speed: 16x max. DVD-ROM and 48x max. CD-ROM  
Write Speed: DVD+R: 16x max., DVD+RW: 8x max.,  
DVD+R DL: 4x max., DVD-R: 16x max., DVD-RW: 6x max.,  
CD-R: 48x max., CD-RW: 24x max.  
Access Time: 120 ms (CD), 140 ms (DVD)  
Mechanism: Motorized tray load mechanism for horizontal  
and vertical use  
Audio: Digital-out and line-out at the back (MPC compatible)  
Interface: IDE/ATAPI  
Burst Transfer Rate: PIO mode 4/Ultra DMA 33  
Cache: 2 MB  
Compatibility: MPC level 3, Multi Read, PC2001  
Media/Modes Supported: DVD-ROM, DVD-R, DVD-RW,  
DVD+R, DVD+R DL, DVD+RW, DVD-Video, CD-ROM,  
CD-ROM XA, CD-Audio, CD Extra, CD Text, CD-I Ready,  
CD-Bridge, Photo-CD, VideoCD, Hybrid CD  
Writing Methods: DAO (disc at once), SAO (session at  
once), TAO (track at once) with zero gap, variable or fixed  
packet, multisession  
Dust Protected Enclosure  
Forced Eject Hole  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Disc Care  
To clean the disc, use a soft cloth and wipe from the  
inside to the outside edge rather than in a circular motion.  
Do not use record-cleaning or anti-static agents as the  
solutions may damage a disc.  
Always store discs in proper storage cases when not in use.  
Check for dirt, dust, or fingerprints on a disc’s recording  
side before inserting into the unit.  
Avoid touching or scratching the recording side of the disc.  
Hold the disc only by the edges or by the center hole and  
one edge.  
Do not affix stickers, labels, or tape to the disc.  
Discard warped or cracked discs as they may cause  
damage to the drive.  
Avoid unusually shaped discs such as “business card” CDs.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Troubleshooting &  
Technical Support  
Nothing happens when eject button is pressed:  
Make sure the power cable is securely connected to the drive.  
Verify the computer is powered-up and running.  
Drive has power (responds to eject button), but is  
not recognized by computer:  
Verify the interface cable is attached correctly.  
Verify the drive’s jumper settings. If your system uses  
CABLE SELECT, verify the jumper settings are set to  
CSEL. If your system is MASTER/SLAVE, verify that there  
is no other device connected to the same cable using the  
same setting.  
Computer shuts down immediately after power-up  
when drive is installed:  
Verify the drive’s jumper settings.  
If drive is the only device connected to the interface cable,  
connect it to the alternate interface cable connector.  
Drive is very loud when reading/writing:  
Make sure the drive is securely mounted to the computer’s  
chassis. Excessive vibration can be caused by loose or  
uneven mounting.  
Still having problems?  
or call (801) 401-1466 for assistance Monday-Friday,  
5:00 a.m. – 5:00 p.m. Pacific Time.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Warranty Information  
ONE (1) YEAR LIMITED WARRANTY  
NEC Solutions (America), Inc. (“NECSAM”) warrants this hardware product (“Product”) against defects in material and  
workmanship for a period of one year from the date of original purchase (as established by the date of purchase on  
your sales receipt) from an authorized NECSAM dealer, retailer or distributor.  
This warranty only covers the hardware packaged with this Product. This warranty does not cover any software  
contained in or included with the Product. Any such software is provided “AS IS.” For your rights with respect to  
software please refer to any software documentation included.  
This limited warranty is valid only for Product purchased within the United States of America. This warranty applies  
only to the original purchaser of the Product and is non-transferable.  
This limited warranty excludes service due to (1) any external cause, including, acts of God, theft, fire, power failures,  
and other electrical and/or environmental problems; (2) accident, misuse, abuse, neglect, unauthorized modifications,  
improper installation or service not authorized by NECSAM; (3) cosmetic damages; (4) usage not in accordance with  
Product documentation and instructions; or (5) problems caused by use of software, parts and components not  
supplied by NECSAM. This warranty does not cover damage or loss to any software programs, data or removable  
discs. This warranty is invalid if the serial number has been defaced, modified or removed.  
If a defect arises and a valid claim is received by NECSAM during the limited warranty period, at its option, NECSAM  
will repair the Product using new or refurbished parts or replace the Product with a new or refurbished Product.  
Repair or replacement is your sole and exclusive remedy. All parts or Products exchanged under this warranty become  
the property of NECSAM. The replacement part or Product is warranted for the remainder of the original limited  
warranty period or thirty (30) days from shipment, whichever is longer.  
NECSAM MAKES NO OTHER EXPRESS WARRANTY WITH RESPECT TO THIS PRODUCT. ANY IMPLIED  
WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS  
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE PERIOD OF THE EXPRESS WARRANTY SET  
FORTH ABOVE, AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED WILL APPLY AFTER SUCH PERIOD.  
NECSAM IS NOT RESPONSIBLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES  
RESULTING FROM ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, NEGLIGENCE,  
STRICT LIABILITY OR ANY OTHER LEGAL THEORY RELATED TO THIS PRODUCT. SUCH DAMAGES INCLUDE, BUT  
ARE NOT LIMITED TO, LOSS OF DATA, LOSS OF BUSINESS, LOSS OF PROFITS, LOSS OF USE OF THE PRODUCT OR  
ANY ASSOCIATED PERIPHERALS, COST OF REPLACEMENT PRODUCT, DOWN-TIME, OR CHARGES FOR  
PURCHASER’S TIME AND EFFORT.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on  
how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This limited warranty  
gives you specific legal rights and you may also have other rights that may vary from state to state.  
Obtaining Warranty Service  
Please call the NEC telephone technical support line listed below.  
Original purchase receipt must be retained and presented to obtain warranty service.  
Request a RMA number and write the RMA number on the outside of the package in a prominent location.  
Return the Product freight prepaid in its original packaging or in other comparable packaging to avoid  
shipping damage.  
Be sure to remove all parts or options not under warranty or any discs prior to returning the Product.  
NECSAM is not responsible for any damage or loss to these items.  
NEC Technical Support  
For telephone technical support please call (801) 401-1466. Telephone technical support hours are Monday–Friday,  
5:00 a.m. – 5:00 p.m. Pacific Time.  
Warranty Registration  
Register your Product online today to help ensure seamless warranty coverage for your new equipment. Failure to  
complete registration does not diminish your limited warranty rights.  
©2005 NEC Solutions (America), Inc. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
NEC Solutions (America), Inc.  
Solutions Platform Group  
2890 Scott Boulevard  
Santa Clara, CA 95050  
Information in this publication is subject to change without notice. NEC is a  
registered trademark of NEC Corporation and/or one or more of its  
subsidiaries. All are used under license. All other trademarks and registered  
trademarks are the property of their respective owners. © 2005 NEC  
Solutions (America), Inc. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Freezer KFN 12823 SD 1 2 User Manual
Miele Washer W 1724 User Manual
Miller Electric Welding System TM 499C User Manual
MTD Log Splitter 24AD598A010 User Manual
Multiquip Portable Generator DCA 56SPX User Manual
NETGEAR Network Hardware WN604 100NAS User Manual
Nexus 21 Stereo Receiver Multi Control User Manual
NordicTrack Treadmill NTTL11990 User Manual
Omega Engineering Thermometer HH802U User Manual
Onkyo Speaker SL 107 User Manual