SP-6457 TD
Concrete Saw
Operation Manual
Revision #1 (05/ 09/ 03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventions
Throughout this manual, the following conventions are used to indicate
important information.
Text set off like this presents clarifying information, specific
instructions, commentary, sidelights, or interesting points of
information.
!
NOTE
Text set off like this indicates that failure to follow directions could
result in damage to equipment.
CAUTION
Text set off like this indicates that failure to follow directions could
result in bodily harm or loss of life.
WARNING
It is extremely important that the operator reads and understands the
safety and message section of this manual.
!
NOTE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CALIFORNIA – Proposition 65 Warning
Engine exhaust and some of its constituents, and
some dust created by power sanding, sawing,
grinding, drilling and other construction activities
contain chemicals known to the State of California to
cause cancer, birth defects and other reproductive
harm. Some examples of these chemicals are:
o Lead from lead-based paints.
o Crystalline silica from brick.
o Cement and other masonry products.
o Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: ALWAYS work in a
well-ventilated area, and work with approved safety
equipment, such as duct masks that are specially
designed to filter out microscopic particles.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
CONVENTIONS.................................................................................................................. 3
SAFETY..............................................................................................................................7
OPERATION....................................................................................................................19
BEFORE STARTING ......................................................................................................... 19
ENGINE POWER, CUTTING POWER & SHEAVE SIZE........................................................ 20
Blade RPM vs Surface Feet Per Minute (SFPM)...................................................... 22
Stacking Blades for Wide Cuts.................................................................................. 24
WATER SUPPLY AND CONTROL...................................................................................... 28
CONTROL PANEL............................................................................................................ 29
HANDLEBARS................................................................................................................. 30
FUELING THE SAW......................................................................................................... 31
STARTING AND STOPPING THE ENGINE.......................................................................... 32
COLD WEATHER OPERATION ......................................................................................... 33
Glow Plugs................................................................................................................ 33
Block Heaters............................................................................................................ 33
Draining the Water System ....................................................................................... 33
POINTER ADJUSTMENT................................................................................................... 34
RAISE — LOWER CONTROLS.......................................................................................... 35
SETTING THE DEPTH GAUGE & DEPTH STOP ................................................................. 36
DRIVE SYSTEM............................................................................................................... 37
Transaxle................................................................................................................... 38
4-Speed BladeShaft................................................................................................... 39
Shifting Gears ........................................................................................................... 40
NIGHT LIGHT.................................................................................................................. 41
TRANSPORTATION TIE-DOWNS AND LIFT POINT............................................................ 41
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE.............................................................................................................43
REMOVABLE GUARDS AND ACCESS PANELS .................................................................. 43
BELTS AND PULLEYS ..................................................................................................... 44
V-Belt Tension........................................................................................................... 44
Adjusting BladeShaft Drive Belt Tension................................................................. 46
Replacing the BladeShaft Belt:................................................................................. 46
Replacing the Jackshaft Belt..................................................................................... 46
BLADESHAFT MAINTENANCE......................................................................................... 48
BladeShaft Replacement ........................................................................................... 48
BLADE COLLAR REMOVAL/INSTALLATION .................................................................... 49
CIRCUIT BREAKERS........................................................................................................ 52
MAXIMUM CUT DEPTH ADJUSTMENT ............................................................................ 52
LUBRICATION................................................................................................................. 53
ENGINE........................................................................................................................... 54
Air and Oil Filter Chart............................................................................................ 54
PTO DRIVE MAINTENANCE ........................................................................................... 55
REPLACING THE BATTERY.............................................................................................. 57
RAISE-LOWER SYSTEM .................................................................................................. 58
JOYSTICK TENSION ADJUSTMENT .................................................................................. 59
HYDRAULIC SYSTEM MAINTENANCE ............................................................................. 60
Routine Maintenance ............................................................................................... 60
Draining & Filling the Hydraulic System................................................................. 61
Bleeding the Depth Stop Cylinder............................................................................. 63
DRIVE WHEEL ALIGNMENT............................................................................................ 64
SPECIFICATIONS..........................................................................................................66
DIMENSIONS..................................................................................................................67
6457 ELECTRICAL SCHEMATIC ….. ............................................................................... 68
Specifications are subject to change without notice.
!
NOTE
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
This Owner's Manual has been developed to provide complete
instructions for the safe and efficient operation of the Multiquip SP-6457
CONCRETE SAW. For engine maintenance information, please refer to
the engine manufacturers’ instructions for data relative to its safe
operation.
Before using this CONCRETE SAW, ensure that the operating
individual has read and understands all instructions in this
manual.
!
NOTE
Safety precautions should be followed at all times when operating this equipment.
Failure to read and understand the Safety Messages and Operating Instructions could
result in injury to you and others.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you about potential hazards that
could injure you or others. The Safety Messages specifically address the level of
exposure to the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
DANGER: You WILL be KILLED or SERIOUSLY injured if you
DO NOT follow directions.
WARNING: You CAN be KILLED or SERIOUSLY injured if you
DO NOT follow directions.
CAUTION: You CAN be injured if you DO NOT follow directions.
Potential hazards associated with SP-6457 Concrete Saw operation will be referenced
with "Hazard Symbols" which appear throughout this manual, and will be referenced in
conjunction with Safety "Message Alert Symbols".
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HAZARD SYMBOLS
Lethal Exhaust Gases
Engine exhaust gases contain poisonous carbon monoxide gas is
colorless and odorless, and can cause death if inhaled. NEVER operate
this equipment in a confined area or structure that does not provide
ample free flow air.
Explosive Fuel
Motor fuels are highly flammable, and can be dangerous if mishandled.
DO NOT start the engine near spilled fuel or combustible fluids. DO
NOT fill the fuel tank while the engine is running or hot. DO NOT overfill
tank, since spilled fuel could ignite if it comes into contact with hot
engine parts or sparks from the ignition system. Store fuel in approved
containers, in well-ventilated areas and away from sparks and flames.
NEVER use fuel as a cleaning agent.
Burn Hazards
Engine components can generate extreme heat. To prevent burns,
DO NOT touch these areas while the engine is running or immediately
after operations. NEVER operate the engine with heat shields or heat
guards removed.
Rotating Parts
NEVER operate equipment with covers, or guards removed. Keep
fingers, hands, hair and clothing away from all moving parts to
prevent injury.
Accidental Starting
ALWAYS place the engine ON/OFF switch in the OFF position,
when the saw is not in use.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Guards and Covers
NEVER operate the saw without blade guards and covers in place.
Adhere to safety guidelines ANSI American National Standards
Institute, OSHA or other applicable local regulations.
Rotating Blades
Rotating blade can cut and crush. Keep hands and feet clear.
Respiratory Hazard
ALWAYS wear approved respiratory protection.
Sight and Hearing Hazard
ALWAYS wear approved eye and hearing protection.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Skin Injection Hazard
NEVER use your hand to find hydraulic leaks. Use a piece of wood
or cardboard. Hydraulic fluid injected into the skin must be treated by
a knowledgeable physician immediately or severe injury or death can
occur.
Over Speed Conditions
NEVER tamper with the factory settings of the engine governor or
engine settings. Personal injury and damage to the engine or
equipment can result if operating in speed ranges above maximum
allowable.
Equipment Damage Messages
Other important messages are provided throughout this manual to help
prevent damage to your concrete saw, other property, or the surrounding
environment.
NOTE
This concrete saw, other property, or the surrounding environment could
be damaged if you do not follow instructions.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
Most accidents involving product operation, maintenance and repair are caused
by failure to observe basic safety rules and precautions. Accidents can often be
avoided by recognizing potentially hazardous situations before an incident
occurs.
General Safety Warnings
§ DO NOT operate or service this equipment before reading this
entire manual. Failure to follow instructions may lead to serious
injury or death.
§ This equipment is to be operated by trained and qualified
personnel only. This equipment should not be operated by
persons under 18 years of age.
§ This equipment is for industrial use and to be used for its
intended purpose only.
§ NEVER operate this equipment when not feeling well due to
fatigue, illness or taking medicine.
§ NEVER operate the saw under the influence of drugs or alcohol.
§ NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to the
equipment and/or injury to user may result. Manufacturer does
WARNING
not assume responsibility for any accident due to equipment
modifications. Unauthorized equipment modification will void all
warranties.
§ NEVER operate this saw without proper protective clothing;
shatterproof glasses, steel-toed boots, respiration mask, and any
other protective devices required by the job.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
§ Before operating the saw, make sure all protective guards are
securely in place. Multiquip saws are supplied with a blade guard,
collar guard and belt guard.
§ Whenever necessary, replace operation and safety decals if they
become difficult to read.
§ Verify the engine start switch is set to the OFF position before
installing a blade.
§ Make sure the operator knows how to turn the engine OFF in case
of an emergency.
§ Do not go near rotating parts (blades, belts, pulleys or wheels)
while engine is running.
§ Catalytic muffler and exhaust gases are extremely hot. Stay clear
of muffler and exhaust gases. Allow these parts to cool before
servicing the saw.
§ Stay clear of the saw while it is being hoisted.
§ Anytime the saw is lifted onto its nose, or tilted fully back, for
maintenance access, the high end MUST be blocked up to prevent
the possibility of crush injury!
WARNING
§ Allow the engine to cool before adding fuel or performing service
and maintenance functions. Contact with HOT components can
cause serious burns.
§ Never operate the saw in any enclosed or narrow area where free
flow of air is restricted. If the air flow is restricted it will cause
serious damage to the saw’s engine and may cause injury to
people. Remember the saw’s engine gives off DEADLY carbon
monoxide gas.
§ ALWAYS refuel in a well-ventilated area; away from sparks and
open flame. Avoid “topping off” the filler port as spills can result.
§ ALWAYS use extreme caution when working with flammable
liquids. When refueling, STOP the engine and allow it to cool.
§ NEVER smoke around or near the machine. Fire or explosion
could result from fuel vapors, or if fuel is spilled on a HOT engine.
§ NEVER operate the saw in an explosive atmosphere where fumes
are present or near combustible materials. An explosion or fire
could result causing severe bodily harm or even death.
§ NEVER use fuel as a cleaning agent.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
General Safety Precautions
§ ALWAYS read, understand, and follow procedures in the
Operator’s Manual before attempting to operate the equipment.
§ Be sure the operator is familiar with proper safety precautions
and operating techniques before using the saw.
§ Make sure the operating area is clear before starting the engine.
§ Maintain this equipment in a safe operating condition at all times.
§ Keep the saw clean. It will work better and last longer.
§ Use proper blades and follow the blade manufacturer’s
recommendations. Match blade rpm (Blade Shaft rpm) to
recommended blade surface feet per minute (SFPM).
§ Tighten the 5/8” blade-mounting bolt to 100-125 foot-lbs. torque.
§ Turn engine OFF prior to fueling the saw.
§ Start engine with the joystick in NEUTRAL to prevent unexpected
saw movement.
§ Do not leave saw unattended while engine is running.
§ Do not start engine on a sloping surface to prevent unexpected
loss of control.
CAUTION
§ Do not park or leave saw unattended on a slope - the saw can roll
when the engine is OFF. Block the unit when leaving.
§ If the saw must be parked on a slope, turn it across the angle of
the slope, to prevent accidental downhill movement.
§ Always store equipment properly when not being used. Equipment
should be stored in a clean, dry location out of the reach of
children. When storing the saw in freezing weather, blow out
water lines to prevent damage to components in the water
delivery system.
§ Prior to service, level the frame surface.
§ Do not over tighten the Blade Shaft drive belt.
§ Turn on water flow prior to starting the engine, to prevent
damage to the impeller of a belt-driven water pump.
§ Don’t pollute! Waste oils and other chemicals must be disposed
of in a manner consistent with local and state environmental
protection regulations.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
BLADE SAFETY
§ ALWAYS inspect diamond blades before each use. The blade
should exhibit no cracks, dings, or flaws in the steel centered core
and/or rim. Center (arbor) hole must be undamaged and true.
§ Examine blade flanges for damage, excessive wear and
cleanliness before mounting blade. Blade should fit snugly on the
shaft and against the inside/outside of the saw.
§ Only cut the material that is specified by the blade. Read the
specifications of the blade to ensure the proper tool has been
matched to the material being cut.
WARNING
§ ALWAYS keep blade guards in place. Exposure of the blade must
not exceed 180 degrees.
§ Ensure that the blade does not come into contact with the ground
or surface during transportation. DO NOT drop the blade on the
ground or surface.
§ The engine governor is designed to permit maximum engine
speed in a no-load condition. Speeds that exceed this limit may
cause the blade to exceed the maximum safe allowable speed.
§ Ensure that the blade is mounted for proper operating direction.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SAW TRANSPORTATION SAFETY
§ Use appropriate lifting equipment to ensure the safe movement of
the saw.
§ DO NOT use the handle bars and/or front pointer as lifting points.
§ NEVER attempt to tow the untrailered saw behind a vehicle.
§ NEVER transport the saw with the blade mounted.
CAUTION
EMERGENCIES
§ ALWAYS know the location of the
nearest fire extinguisher.
§ ALWAYS know the location of the
nearest first aid kit.
§ In emergencies always know the
location of the nearest phone or
keep a phone on the job site.
Also know the phone numbers of the
nearest ambulance, doctor, and fire
department. This information will be
invaluable in the case of an emergency.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE OPERATION AND SAFETY DECALS
The Multiquip SP-6457 TD Saw is equipped with a number of operation and
safety decals. Should any of these decals become unreadable, replacements can
be obtained from your dealer.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial Tag
Fig. 1 — Serial Tag
For future reference, fill in the model number and serial number of
your saw in the spaces on the label above.
!
NOTE
The serial tag contains the model number and serial number of the saw. This
information details all parts that were included with the saw when it was
shipped from the factory, as well as the date of manufacture.
Record these numbers, in case you need to contact Multiquip in the future.
Record your ENGINE model, specification number and serial number here:
MODEL NO.
SPEC. NO.
SERIAL NO.
The SERIAL TAG is bonded to the panel forward of the console (between the
console and the engine. (See Figure 2.)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE SERIAL
NUMBERS
SERIAL TAG
Fig. 2 — Serial Number Locations
§ The 5/8” blade-mounting bolt on the right side of the saw (as
viewed from the operator’s position) has a left hand thread, while
the blade-mounting bolt on the left side of the saw has a right
hand thread.
!
§ Most saw hardware is measured in English (inch) units. The
Illustrated Parts List notes any Metric hardware. Be sure to use the
correct hardware and proper tools.
NOTE
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Before Starting
Before starting the saw, carefully follow the checklist below:
r Securely install the Belt Guard (2).
r Fully slide on the Collar Guard (3).
r Verify that proper-sized Blade Guard (4) is fully installed on the Blade
Guard mounting tab.
r Confirm the rear and side access panels (5) (6)& (7) and engine
protector are in place.
r Wear eye and hearing protection and protective clothing.
r Adjust handle bars (1) for best operator control.
r If a belt driven water pump is installed, do not run the engine with the
water pump switch on, unless the water supply is connected and
water is flowing.
Fig. 3 — Guards & Panels
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine Power, Cutting Power & Sheave Size
The cutting capability of your saw is a relationship between engine power (as
reflected in the engine RPM) and the speed (RPM) of the Blade Shaft. The diesel
engine of the SP-6457 TD runs at 2800 RPM (full load). If 2800 RPM was a
desirable Blade Shaft speed for the average conditions in which you work, we
would use the same size sheave on the engine shaft and the Blade Shaft; and the
ratio between the two would be 1 : 1.
1 : 1
1.4 : 1
Blade Shaft
Engine
Blade Shaft
Engine
Fig. 4 — Blade Shaft Ratios
If, however, for your cutting conditions, you need a Blade Shaft speed slower
than the engine speed (and this is usually the case), then we need to INCREASE
the ratio between the two speeds by putting a larger diameter sheave on the
Blade Shaft. This, in effect, is what occurs when you shift gears on the SP-6457
TD.
If, for example, you know from experience that you need a Blade Shaft speed of
2000 RPM for the size of blade you normally use (see the Blade RPM vs. SFPM
Chart, below):
2800 (engine RPM) ÷ 2000 (desired BS RPM) = 1.4
This is the ratio 1.4 : 1, which means that for every 1.4 revolutions of the engine,
the Blade Shaft only turns once.
Ratios greater than 1 : 1 also have the beneficial effect of increasing the torque of
the Blade Shaft by the same factor (1.4 in our example) . The manufacturer
advertises that the Deutz BF31011 diesel engine develops 123 ft. lbs. of torque.
To find the theoretical torque of our example saw setup:
123 x 1.4 = 172.2 ft. lbs.
Actual torque of the saw will vary somewhat. In general, more torque means
more cutting power.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Typically, however, the ratios are not used to design a level of torque; they are
used to create a saw with the optimum blade speed (blade Shaft RPM) for you.
The major factors are:
·
·
diameter of blade(s) you commonly use, and
cutting conditions you work under
The 4 gear ratios we have designed into the SP-6457 TD 4-speed Blade Shaft are:
1st Gear
2nd Gear
3rd Gear
4th Gear
1.00 : 1
1.34 : 1
1.70 : 1
2.02 : 1
In addition to the four” fixed” ratios of the Blade Shaft gears, we can also tailor
the Blade Shaft RPM (blade speed) by adjusting the “primary” ratio between the
engine and the Blade Shaft. By selecting a Blade Shaft sheave and Engine sheave,
a multitude of additional ratios (and Blade Shaft speeds) are possible. The
following Sheave sets are available as standard kits:
Engine
Sheave
Blade Shaft
Sheave
Engine
RPM
Ratio
Blade Shaft RPM
Kit #
2333 in 1st
1741 in 2nd
1372 in 3rd
1154 in 4th
5.1
5.4
6.0
5.6
1.17 : 1
2800
2800
18609
2700 in 1st
2000 in 2nd
1588 in 3rd
1350 in 4th
1.03 : 1
.83 : 1
18611
18612
3373 in 1st
2498 in 2nd
1984 in 3rd
1686 in 4th
6.0
5.0
2800
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade RPM vs. Surface Feet Per Minute (SFPM)
When choosing a blade for your cutting conditions, follow the blade
manufacturer’s recommendations. Match the blade speed (Blade Shaft RPM) to
the recommended blade Surface Feet Per Minute (SFPM).
SFPM
16”
diam.
RPM
18”
diam.
RPM
20”
diam.
RPM
24”
diam.
RPM
26”
diam.
RPM
30”
diam.
RPM
36”
diam.
RPM
42”
diam.
RPM
48”
diam.
RPM
8,000
8,500
1910
2029
2149
2268
2387
2507
2626
2745
2865
2984
3104
3229
3349
3468
1698
1804
1910
2016
2122
2228
2334
2440
2546
2653
2759
2866
2972
3078
1528
1623
1719
1814
1910
2005
2101
2196
2292
2387
2483
2581
2676
2772
1273
1353
1432
1512
1592
1671
1751
1830
1910
1989
2069
2149
2229
2308
1175
1249
1322
1396
1469
1543
1616
1690
1763
1836
1910
1985
2058
2132
1019
1082
1146
1210
1273
1337
1401
1464
1528
1592
1655
1719
1783
1847
849
902
728
773
636
676
9,000
955
819
716
9,500
1008
1061
1114
1167
1220
1273
1326
1378
1433
1486
1532
864
756
10,000
10,500
11,000
11,500
12,000
12,500
13,000
13,500
14,000
14,500
910
796
955
836
1001
1046
1092
1137
1183
1228
1273
1319
875
915
955
995
1035
1074
1114
1153
§ Verify that the engine start switch is OFF before installing blade.
§ Tighten the 5/8” blade-mounting bolt to
125-175 foot-pounds torque.
CAUTION
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Blade
The blade can be mounted on either side of the saw to accommodate different
cutting jobs.
1. Raise the saw so that the blade will clear the ground when installed.
2. Verify that blade collars are clean and undamaged.
3. Insert the bushing and mounting bolt through the outer collar and blade.
·
Align collar pin through the blade into the inner collar.
4. Tighten the 5/ 8” mounting bolt to 125-175 foot-pounds of torque.
·
The blade-mounting bolt on the right side of the saw (as viewed from the
operator’s position) has a left hand-thread, while the blade-mounting bolt
on the left side of the saw has a right-hand thread.
Blade Guard
Mounting Clip
Outer Collar
with Pin
Inner Collar
Collar
Bushing
Tapered
Blade Shaft
Mounting
Bolt
Fig. 5 — Installing the Blade
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Stacking Blades for Wide Cuts
NEVER attempt to stack blades beyond the capacity of the Kits
described here. NEVER operate the saw without blade guards in
place.
WARNING
Combining (stacking) blades together to make wide cuts requires an optional
Bushing Extension Kit.
·
·
Kit #18501 allows blade stacking from .375” to .75” thickness.
Kit #18502 allows blade stacking from .75” to 1.125” thickness.
The kits consist of an outer collar with a longer pin, an extended bushing, and
longer bolts.
1. Remove the existing Blade (see Installing the Blade, above).
2. Replace the standard Collar Bushing, Outer Collar, and Mounting Bolt that
came with the saw, with the extended Bolt and Bushing and the new Outer
Collar that came with the Kit.
·
The Mounting Bolt for the right side of the saw (as seen from the
operator’s position) has a left hand-thread, while the Mounting Bolt for
the left side of the saw has a right-hand thread.
3. Insert the Bushing and Mounting Bolt through the Outer Collar and stack of
Blades. The longer bushing and bolt allow blades to be stacked together
4. Align the Collar Pin through the stack of Blades into the Inner Collar.
5. Tighten the 5/8” Mounting Bolt to 125-175 foot-pounds of torque.
Outer Collar with extended pin
Inner Collar
Extended bushing
Extended bolt
Fig. 6 — Blade Stacking
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing and Removing the Blade Guard
Blade Guards are “ambidextrous” – that is, they can be installed on either side of
the saw.
Installing the Blade Guard
1. Slide the Blade Guard Mounting Clip onto the Guard Mounting Tab on the
frame.
2. Connect the water delivery hose to the Blade Guard.
·
Ensure that the water pipes are pointed toward the water distribution
grooves in the Blade Collars.
3. Make sure the front-hinged section of the Blade Guard is fully closed before
use.
Top Handle
Water
Delivery
Hose
Blade Guard
hinged front
Water
Distribution
Manifold
Rear Handle
Blade Guard
rear section
Mounting Clip
Fig. 7 — The Blade Guard installed
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Guard Water Supply
Verify that the water hose on the saw is connected to the Blade Guard and that
the water pipes are pointed into both Blade Collars.
Make sure that the 90º outlets of the water tubes point toward the
lower portion of the blade collars, aimed at the delivery ports, for
proper water delivery to the blade.
CAUTION
Water Tube bracket
Water Tube aimed at
groove in Blade Collar
Blade Collar
Fig. 8 — Water Tubes and the Blade Collar
Removing the Blade Guard
During use, the Blade Guard can become tight on the tapered mounting tab. To
loosen it, wiggle the Rear Blade Guard Handle up and down, while lifting with
the Top Handle.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Collar Guard
The Collar Guard protects unused Blade Collars.
1. Slide the Collar Guard (1) onto the Guard Mounting Tab on the frame.
2. Verify that the unused Blade Collar (2) is secured to the Blade Shaft, by
tightening the mounting bolt (3).
1 – Collar Guard
2 – Blade Collar
3 – Mounting Bolt
Fig. 9 — The Collar Guard, Installed
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Water Supply and Control
§ To prevent damage to the impeller of a belt driven water pump, do
not run the engine with the water pump switch on, unless the
water supply is connected and water is flowing.
§ When storing the saw during freezing weather, blow out the water
CAUTION
lines to prevent damage to the water delivery system.
1. Connect the water supply hose to the water inlet (garden hose) fitting (1) on
the left side of the saw.
2. Verify that the water hose on the saw is connected to the Blade Guard (5) and
that the water tubes are pointed into both Blade Collars.
3. The yellow lever (4) on left side of the control panel regulates water flow
volume. The other lever (3) turns the water On and Off.
4. If the saw is equipped with an optional water pump, the ON/ OFF switch (2)
is on the control panel next to the water flow control valve.
Because of the water delivery efficiency of the 24-port blade collars,
your saw will use less water for blade lubrication than other water
deliver systems.
!
NOTE
3
4
2
5
1
Fig. 10 — The Water Supply System
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Panel
Ignition Switch
ON-OFF
Depth
Indicator
Auxiliary
Switch
Light
Switch
Engine Status
Indicator
Blade shaft
Tachometer
Pointer Cable
Cam Cleat
Throttle
Engine
Tachometer
Voltmeter
Drive
Disengage
Operating
Instructions
Depth
Stop
Valve
Upper
Plunge
Button
Water
ON/OFF
Control
Valve
Speed
Control
Joystick
Water
Flow
Control
Lower Plunge
Button
Maintenance
Information
Water Pump
Switch
Raise Button
(Option)
Fig. 11 — The Control Panel
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Handlebars
The handlebars are adjustable to three different angles, for optimum operator
control, and can also be slid fully inward for storage. Once handlebars are
adjusted, lock them into position by tightening the lock knob on each side.
Lock Knob
P3
P2
P1
Three
operating
positions
Storage
position
Fig. 12 — Handlebar Positions
Using the handlebars in position #2 or #3 when employing larger diameter
blades, reduces the need to bend over, and reduces the effort required by the
operator to maneuver the saw.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Fueling the Saw
The saw features a 10-gallon, clear, molded plastic fuel tank with a sight gauge,
central drain, and shutoff valve. The fuel tank cap is located at the front of the
control console.
§ Be sure the engine is turned off prior to fueling the saw.
§ Do not spill diesel fuel on control panel or engine.
§ Do not over-tighten gas cap.
CAUTION
Use
WARNING
Fuel Tank Cap
Sight Gauge
Shut-off Valve
Fig. 13 — Fuel System
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting and Stopping The Engine
§ Do not leave the saw unattended while the engine is running.
§ Do not start, park, or leave the saw unattended on a slope.
§ If the saw has an optional water pump, do not run the saw dry
with the water pump switch ON — otherwise the pump impellers
will be damaged.
§ Do not stop the engine abruptly when hot! Reduce the throttle to
idle and allow the engine to run one or two minutes before turning
the ignition switch off. This allows the engine to cool down, and
prevents damage to the Turbo unit.
CAUTION
1. Move the speed control joystick to NEUTRAL position.
2. Set the throttle to IDLE.
3. Ensure that water lines are attached and water is flowing to the saw.
4. Momentarily turn the ignition switch to the START position.
·
Allow the engine to warm up for several minutes.
5. Set the throttle to the recommended engine RPM to match the recommended
blade speed of the attached blade.
6. Lower the blade to the cut depth.
7. Move the joystick FORWARD to advance the cut.
8. To stop the engine, turn the ignition switch to the OFF position.
Fig. 14 — ON/OFF Switch Location
§ Make sure the operator knows how to turn the engine off in case
of an emergency.
§ Do not go near rotating parts (blade, belts, pulleys, or wheels)
WARNING
while the saw is running.
Restarting After Running Out of Fuel
The 1011 series Deutz engines do not require bleeding the fuel system if you run
out of fuel. To restart the engine, simply re-fill the fuel tank, and crank the
engine normally (should be only 5-10 seconds) until it re-starts.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Cold Weather Operation
Glow Plugs
Optional Glow Plugs are installed inside the air intake. In cold weather (low
temperatures below 40°F):
1. Rotate the Ignition Switch PAST the ON position to the GLOW PLUG
position and HOLD there for 20-40 seconds.
2. After 20-40 seconds, continue to rotate the switch to the START position.
3. Once the engine has started, let the switch go-it will return to the ON
position.
In extreme cold weather (below 20°F), 2 or 3 cycles of Glow Plug may be
necessary before the engine will start.
Block Heaters
Optional Block Heaters, (installed directly on the crankcase), are operated by
plugging them into an electrical outlet via an extension cord. The block heater is
NOT thermostatically controlled. Use only just prior to saw use. DO NOT leave
the saw unattended with block heater in operation and DO NOT use when low
temperatures are above 20°F.
§ Do not leave optional Block Heaters plugged in for extended
periods when temperatures may rise above 20°F. The oil could
“cook” inside the crankcase and damage to the engine could
result.
CAUTION
§ If the Water System is not drained when the saw is not in use and
temperatures fall below 32°F, damage may occur to optional water
pumps and/or oil coolers.
Draining the Water System
When low temperatures fall below 32°F:
1. If the saw is equipped with an optional Water Pump, open the drain petcock
on the pump and allow the pump to drain.
·
With the engine running, turn the water pump switch on for a few
seconds to purge water remaining inside the pump body.
2. Tilt the saw up and back, to allow water to drain.
3. Tilt the saw forward, to allow water to drain again.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
4. If an air compressor is available, blow out the system by applying
compressed air to the Water Inlet (see Fig. 10).
Pointer Adjustment
1. Lower the front pointer assembly.
·
·
Adjust the pointer rod (1) by loosening the lock knob (2).
Once the pointer rod is set to the cut line, tighten the lock knob.
2. Adjust the rear pointer to the cut line:
·
Loosen the lock bolt, position the pointer rod, and tighten the lock bolt.
3. To raise the front pointer assembly, pull back and up on the pointer cable (3).
·
Secure the pointer assembly in the desired raised position by locking the
cable between the jaws of the cam cleat (5).
6
5
4
3
2
1
Fig. 15 — Pointer Adjustment
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Raise — Lower Controls
This saw uses a 12-volt hydraulic pump and cylinder to raise and lower the
blade. The SP-6457 TD saw has a plunge button and a raise button. Controls are
located on the joystick handle.
1
2
3
Fig. 16 — Joystick Handle Controls
1. To slowly lower the blade to the cut, push the top button (1).
2. For a fast plunge to the cut, push the bottom button (2).
3. For a very fast plunge, press both buttons simultaneously.
4. To lift the blade, hold down the Raise button on the side of the handle (3).
See the Maintenance section of this manual for an illustration of the Raise-Lower
System components, and troubleshooting techniques.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Depth Indicator
1. Lower the blade until it just touches the cutting surface.
2. Set the Depth Indicator dial to zero. (The Depth Indicator now accurately
indicates how deep the blade is cutting.)
Setting the Depth Stop
This saw uses a hydraulic Depth Stop to position and lock the blade at the
desired cut depth.
1. Depress SLOW LOWERING button until blade has reached desired cutting
depth.
2. While holding the Slow Lowering button, open the Depth Stop Valve.
3. Close the Depth Stop Valve.
4. Release the SLOW LOWERING button.
5. The saw will now repeatedly lower to the set cutting depth, until the Depth
Stop is re-adjusted.
Slow Lowering
Depth Indicator
Depth Stop Valve
Fig. 17 — Setting the Depth Gauge and Depth Stop
To disable the Depth Stop when it is not needed:
1. Open the Depth Stop Valve.
2. Set the Blade Collars on the ground.
3. Close the Depth Stop Valve.
Do not cut with the Depth Stop Valve in the OPEN position; this could
cause the blade to rise out of the cut.
CAUTION
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Drive System
This saw has a cable-controlled Hydro-Gear hydrostatic powered transaxle with
infinite F-N-R speed adjustment via a joystick controller. The saw is designed
with locked axle drive, and can travel at speeds up to 300 feet per minute.
Drive System Controls
The panel-mounted joystick controls FORWARD-NEUTRAL-REVERSE
(F-N-R) and infinitely variable speeds in both directions. To increase forward
speed, slowly move the joystick FORWARD. Pulling the joystick backward
decreases saw speed, and when the joystick passes NEUTRAL the saw moves
into REVERSE. Reverse speed is also controlled by the position of the joystick.
The Drive Disengage handle, when pulled, puts the saw in “free wheeling”
mode. This is not a “true” Neutral, but does provide a by-pass in the
pump/ motor group which allows the saw to be readily moved. Some rolling
resistance will be encountered.
Speed Control
Joystick in
NEUTRAL
Drive Disengage
Fig. 18 — Drive System Controls
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Transaxle
The Hydro-Gear hydrostatic-powered transaxle has no chains, sprockets or open
gears to service. There is a simple cable control. The remote filter promotes long
life and easy maintenance.
Drain Plug
Fig. 19 — The Transaxle
38
Download from Www.Somanuals.com. All Manuals Search And Download.
4-Speed Blade Shaft
The exclusive 4-speed Blade Shaft allows optimum performance with a variety of
different blade sizes under a wide range of conditions.
Fig. 20 — The 4-Speed Blade Shaft
The 4-speed design fully encloses the transmission, bearings and Blade Shaft,
and features an oil bath lubrication (no grease fittings). Oil is cooled, filtered and
circulated, and the assembly utilizes a remote, protected fill and vent. Gear
changes are made with rack & pinion shifting. Positive shift lock prevents the
multi-speed Blade Shaft from jumping out of gear. A Blade Shaft tachometer
assists in gear selection.
The 4 gear ratios are:
1st Gear
2nd Gear
3rd Gear
4th Gear
1.00 : 1
1.34 : 1
1.70 : 1
2.02 : 1
The 1: 1 ratio is for the smallest diameter blade. The middle two ratios are for
intermediate sized blades and the 2.02 : 1 ratio is for the largest blade. Blade
range is from 16” to 48”.
discussion of the 4-speed Blade Shaft, gears, and sheave ratios.
To calculate Blade Shaft speed, assuming a 1:1 ratio between engine and blade
shaft input, divide engine speed by the selected ratio. For example, for the 3rd
gear Blade Shaft RPM: 2500 Engine RPM ÷ 1.7 = 1470 Blade Shaft RPM in 3rd gear.
The gear pattern is marked on the casting around the shift lever.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
§ Never shift gears with the engine running.
§ Before inserting the Shift Wrench, verify that the ignition is OFF.
§ Disengage the Shift Lock before shifting, and engage the Shift Lock
after shifting.
WARNING
§ Remove the Shift Wrench before starting engine.
Shifting Gears
1. Verify that the ignition switch is OFF. This prevents accidentally starting the
engine while shifting gears.
2. Insert the Shift Wrench through the marked hole in the belt guard.
3. Pull and rotate the Shift Lock to disengage it.
4. Shift gears by turning the Shift Lever counter-clockwise from 3à1à2à4 or
clockwise from 4à2à1à3.
·
Slightly rock the Shift Wrench while turning the Shift Lever to the desired
gear, to make shifting easier.
5. Push and turn the Shift Lock, to lock the selected gear.
6. Slightly rotate the Shift Lever to verify the gear shift lock has popped into
place.
7. Remove the Shift Wrench before starting the engine.
§ DO NOT leave the Shift Wrench in the belt guard when starting the
engine. Injury to the operator or equipment damage is likely to
result.
WARNING
8. Use the Blade Shaft tachometer to verify that recommended blade rpm
matches blade manufacturer’s recommendation.
Shift Instruction Decal
Shift Lever
Shift Lock
Insert
Shift Wrench
Here
Fig. 21 — Gear Shift Components
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Night Light
The night light can be used on either side of the saw, and can be extended and
rotated for best illumination of the cutting area. Aim the light, then lock it in
position by tightening the lock knobs. The light can be removed for storage by
loosening the lock knobs, disconnecting the light cord and sliding the light bar
out of the saw.
Lock
Knob
Lock
Knob
Fig. 22 — Night Light
Transportation Tie-downs and Lift Point
Tie-downs
The saw is provided with holes at each corner of the lower frame for easy tie-
down during transportation. The ½” all-thread J-bolts, with which your saw
was attached to its shipping pallet, can be used in a variety of tie-down scenarios.
It is highly recommended that the saw be tied down any time it is being transported.
Tie-down
Tie-down
Fig. 23 —Tie-down Points
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Lift Point
The convenient single point for lifting the saw with a hoist is located just in front
of the console, between it and the engine.
Lift Point
Fig. 24 — Lift Point
§ To avoid possible injury, stay clear of the saw while it is being
hoisted.
§ To avoid possible damage to the saw, use approved rigging
(minimum 2000 lb. test) when hoisting the saw.
WARNING
42
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
This saw has many service-saving features, such as fully enclosed oil bath
lubricated Blade Shaft bearings, which require no daily lubrication.
Level the saw frame surface prior to service to get accurate oil level
readings.
!
NOTE
Removable Guards and Access Panels
For ease of service access, the following guards and panels are removable:
· Blade Guard (4)
· Belt Guard (2)
· Rear Access Panel (5)
· Console Access Panel (6)
· Collar Guard (3)
Belt Tension Panel (7)
·
Replace guards and panels prior to starting the engine.
Fig. 25 — Guards & Panels
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Belts and Pulleys
Belt
Qty Part Number
Blade Shaft Drive Belt (5)
2
Part # 520009
Jackshaft Belt (3)
1
1
Part # 521012
Part# 521004
Transaxle Drive Belt (2)
Part# 521006
Part# 521008
Water Pump Option Belts
1
JackShaft
1
2
5
3
4
Belt Tensioner Pulley
Fig. 26 — Belt Locations
V-Belt Tension
Ideal V-Belt tension is the lowest tension at which the belt will not slip under
peak load conditions. Check V-Belt tension frequently during the first 24-48
hours of run-in operation.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
§ Over-tensioning shortens belt and bearing life.
§ Keep belts clean of foreign material that may cause slippage.
§ Make V-Belt inspection a periodic procedure.
§ Never dress belts, as this can cause premature failure.
CAUTION
Adjusting Blade Shaft Drive Belt Tension
When tightening or loosening drive belts, raise the saw to reduce
stress on the tensioning system, and gravity will assist you by pulling
the engine backwards slightly.
!
NOTE
1. Access the Panel on the side of the saw, loosen the Engine Mount Lock
Bolts to allow the engine to rotate forward.
·
Requires 15/ 16” socket, 10”- 12” extension and ratchet or breaker bar.
Access Panel
Engine Mount
Lock Bolt
Engine Mount
Lock Bolt
Fig. 27 — Engine Mount Lock Bolts
45
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Loosen the jam nut on the Single Point Belt Tension Bolt.
Single Point Belt
Tension Bolt
Jam Nut
Fig. 28 — Single Point Belt Tension Bolt
3. Adjust drive belt to the desired tension. DO NOT over tighten.
4. Tighten the Engine Mount Lock Bolt.
5. Turn the Single Point Tension Bolt until the head of the bolt no longer
touches the frame. Tighten the jam nut to prevent the bolt from turning.
Replacing the Blade Shaft Belt:
(See Fig. 27 & 28)
1. Remove the lower belt guard from around the Blade Shaft sheave.
2. Loosen the engine mount lock bolts.
3. Loosen the single-point belt-tensioning bolt to allow the engine to roll
forward.
4. Slide the belt off of the engine sheave and pull the belt down around
the Blade Shaft sheave.
5. Slide the belt off the top of the Blade Shaft sheave.
6. Reverse the order to install a new belt.
Replacing the Jackshaft Belt
(See Fig. 29)
1. Remove the Belt Guard.
2. Loosen the Rotary Tensioner Pulley.
3. Replace the Jackshaft Belt.
4. Adjust the Rotary Tensioner.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Rotary Belt Tensioner
The Rotary Belt Tensioner system uses a 3/ 4”-headed bolt and a 15/ 16” or 1”
nut to set belt tension by positioning an arm between the Tensioner Pulley and
the Tensioner Base. Ridges on the Base mark the amount of tension.
1. Loosen the Bolt Head.
2. Rotate the Tensioner Nut clockwise until the desired belt tension is
achieved.
3. Tighten the Bolt Head.
4. DO NOT OVER-TIGHTEN.
Engine Sheave
1
2
JackShaft Pulley
3
Tensioner Pulley
5
4
Tensioner Nut—
Tensioner Bolt Head is
on opposite side
Tensioner Base
Fig. 29 — The JackShaft Belt and Rotary Belt Tensioner System
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Shaft Maintenance
The fully enclosed Blade Shaft eliminates most maintenance. However, should
the Blade Shaft need service or repair, contact Multiquip for details.
Fig. 30 — 4-Speed Blade Shaft
Blade Shaft Replacement
To assure correct Blade Shaft/ Wheel alignment it is recommended that this
operation be performed by a Multiquip Authorized Service Center.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Collar Removal/Installation
Correct removal or installation of the Inner Blade Collar or Flange requires the
Collar Puller (option Part Number 18503) shown in Figure 31.
Follow instructions closely to prevent injury from flying Blade Collars!
Because of the tapered fit between Blade Collar and Blade Shaft,
5-10 tons of force is needed to release the inner collar. Parts and
tools can become dangerous projectiles if instructions are not
followed properly.
WARNING
Fig. 31 — Using the Collar Puller
Removing the Inner Blade Collar
With the Outer Blade Collar in place, and the Blade Mounting Bolt loosened
approximately ¼”:
1. While the three perimeter bolts hold the two Puller Plates together, slide
the Horseshoe Plate of the Collar Puller behind the (Shaft) side of the
Inner Collar as shown above.
2. Tighten the center Puller bolt to remove the Inner Collar from the Blade
Shaft.
·
Having the Outer Collar in place prevents the Puller and Inner Collar from flying
off when the taper breaks loose, and causing injury!
·
If the Inner Collar does not readily come free from the tapered Blade
Shaft, lightly tap on the central Puller bolt. This should cause the collar to
break free from the shaft.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Inner Blade Collar
1. Ensure that the tapered portion of the Blade Shaft, and the Inner Blade Collar
are perfectly clean and free of burrs or indentations. Clean and repair as
necessary
2. Ensure that the Drive Key is in place.
3. Slide the Inner Collar onto the tapered portion of the Blade Shaft
·
DO NOT use any lubricant! Lubricant prevents the tapered surfaces of the
Collar and Shaft from mating properly.
4. Install the Outer Blade Collar, Collar Bushing, and Mounting Bolt.
·
Tighten with a ½” impact wrench to seat the tapered surfaces of the Inner
Collar and Blade Shaft.
Mounting Bolt
Collar Bushing
Outer Collar
Dowel pin
Inner Collar
Drive Key
Blade Shaft
Fig. 32 — Installing the Inner Blade Collar
50
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Loosen the Mounting Bolt and remove the Outer Collar and Bushing.
6. Inspect the Inner Collar to ensure the proper seating of the tapered fit.
·
The Inner Collar should be seated between .030” and 0.0” (flush) to the
end of the Blade Shaft.
Inner Collar
Blade Shaft
Fig. 33 — Proper seating of the Inner Collar on the Blade Shaft
7. Test to ensure that the Inner Collar does not wobble when rotated. Use an
indicator dial on the face of the Collar. Maximum tolerance is .003” run out
on the face of the Collar.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Circuit Breakers
Three thermal circuit breakers are located inside the top of the Console.
Remove Panel to
access circuit
breakers
Fig. 34 — Circuit Breaker location
Under normal circumstances circuit breakers do not require service; they are
automatically re-set when an overload condition is corrected. If a breaker is
cycling on/ off, locate the cause of the electrical overload and repair as required.
Maximum Cut Depth Adjustment
This saw comes factory-adjusted for maximum usable cut depth. However,
should you desire to change this setting:
1. Park the blade-less saw on a flat and level surface.
2. Fully lower the saw onto the Stop Bolts (see Fig. 35).
3. Measure the distance from the Blade Collars to the surface.
4. Adjust the Stop Bolts in or out until the Blade Collars have 1/ 8” to 3/ 16”
ground clearance.
5. Ensure that both bolts are adjusted to the same settings so the load is evenly
distributed.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Lubrication
This saw has five grease fittings on the front axle assembly.
·
·
·
Front axle pivot bearings (F1 & F3)
Hydraulic lift cylinder ends (F2, and far end of cylinder)
Depth Stop Pivot Plate (F4)
These fittings are easily accessed by raising the saw half way up, and then lifting
the rear of the saw until the blade collars rest on the ground.
To prevent the possibility of crush injury, ensure that the saw is
securely placed on blocks before servicing the lubrication points.
WARNING
Grease fittings every 50 hours of operation with a premium grade
waterproof E. P. (extreme pressure) grease.
CAUTION
Maximum Cut Depth
Stop Bolt
Maximum Cut Depth
Stop Bolt
F2
F1
F3
F4
Fig. 35 — Grease Fittings and Maximum Cut Depth Stops (view from back of saw)
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine
The Model SP-6457 TD features a Turbocharged 57 HP Deutz diesel engine. See
the engine manual for service details and oil recommendations.
·
·
Check air filters daily, replace as required. Do Not clean air filters.
Check engine oil level daily.
·
·
Level the frame prior to service to get an accurate reading.
Do Not over-fill with oil.
·
Change engine oil and filter every 125 hours of operation
Safety Air Filters are not intended to be used for primary air
filtration.
When the Primary Filter gets clogged, replace it
immediately — do not run saw using just the Safety filter.
CAUTION
Air and Oil Filter Chart
Filter
Qty Part Number
Primary Air Filter
Safety Air Filter
Engine Oil Filter
Hydraulic System Filter
Fuel Filter
1
1
1
1
1
300004-1 (Donaldson #P827653)
300004-2 (Donaldson #P829332)
306012 (Deutz # 1174416-SP)
306002 (HydroGear # 51563)
304010 (Donaldson # 1174696)
Engine
Oil filter
Transaxle
filter
Fuel filter
Fig. 36 — Remote Filters
54
Download from Www.Somanuals.com. All Manuals Search And Download.
PTO Drive Maintenance
Disassembly of the PTO Drive and replacement of the PTO Drive
Sheave/ Bearing Assembly requires the PTO Bearing Puller
(P/ N 18610). The Sheave/ Bearing Assembly is not serviceable and must be
replaced as a complete unit.
1. Remove the Drive Belt (see Replacing the Blade Shaft Drive Belt).
2. Remove the Drive Plate Assembly from the engine.
·
·
The Assembly is held on by 11 bolts.
Note the clocking orientation of the plate.
3. On the workbench:
·
·
Remove the Cap Screws and End Cap (Items 1 & 2, Fig. 37).
Remove the Splined Drive Cap Screws and the Drive Cap (Items 3 & 4,
Fig. 37).
·
·
With a sharp pointed awl or similar tool, remove the flat wound spiral
retaining ring (Item #5, Fig. 37)
Attach the PTO Bearing Puller in place of the Splined Drive Cap, as shown
in Fig. 37.
·
·
·
Insert the Puller Alignment Bushing (1).
Attach the Puller Cap (2) with the Drive Cap Screws (3).
Thread in the PTO Bearing Puller Bolt (4).
Fig. 37 — Attaching the PTO Bearing Puller to the Drive Plate Assembly
·
Tighten the Puller Bolt (4), to pull the Sheave/ Bearing Assembly off
of the Bearing Support (Fig. 38, #9).
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 38 — PTO Drive Sheave/Bearing Assembly
Re-Assembling the PTO Drive
1. Clean and inspect all parts.
2. Use a press to push the new Bearing/ Sheave assembly onto the Bearing
Support (9) until the bearings contact the shoulder of the Support.
3. Use a sharp pointed awl or similar tool to install the flat-wound Spiral
Retaining Ring (5) into the top groove of the Bearing Support (9).
4. Install the Splined Drive Shaft (10) in the Splined Drive Shaft Flange (15).
5. Slide the PTO Drive Plate assembly over the Splined Drive Shaft.
6. Bolt the plate to the Engine, making sure to clock the plate to its original
position.
7. Re-install the Splined Drive Cap (4) and bolts (3), with a low-strength
thread-locker (LocTite™ 242 or equivalent).
8. Install the End Cap (2) and screws (1).
9. Replace the Drive Belt.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Battery
This saw uses a Group 75, 12-Volt, 1000 cold cranking amp battery. To replace
the battery:
1. Remove Engine Guard and Upper Belt Guard.
2. Loosen the Rotary Tensioner and remove the Transaxle Belt.
3. Loosen the two Engine Mount Lock Bolts and the Single Point Belt
Tension Bolt.
Single Point Belt
Jam Nut
Engine Mount
Lock Bolt
Access Panel
Fig. 39 — Engine Mount Lock Bolts Single Point Belt Tension Bolt – from Belt Tension
4. Tilt the saw down and roll the engine as far forward as possible, to create
the maximum access opening. See figure 40.
5. Disconnect the battery cables, Positive first, to avoid arcing.
6. Remove the forward battery tie-down clip.
7. Carefully roll the battery up and maneuver it out through the space
between the Control Console and the Engine.
8. To replace the battery, repeat steps 1-5 in reverse order
Fig. 40 — Engine Rotated Forward to Remove the Battery
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Raise-Lower System
This saw uses a 12-volt hydraulic pump and hydraulic cylinder to power the
raise-lower system.
·
·
·
·
Level frame prior to service to get an accurate reading.
Check oil level daily.
Fill the reservoir half to two-thirds full when cold
Use 5W-30 premium grade engine oil.
Depth Stop Valve
Lift Pump
Reservoir
2
3
Lift
Pump
1
Depth Stop
Cylinder
4
5
Hydraulic
Manifold,
Lowering
valves
Lift Cylinder
Fig. 41 — Raise-Lower System
Raise/Lower Troubleshooting
If your new saw begins lowering all by itself when you release the Raise button,
the problem may be caused by debris in the hydraulic line which is blocking the
Lower valve in the open position.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Joystick Tension Adjustment
The speed control joystick uses friction adjustment to provide the preferred
“feel”:
1. Using a ¼” Allen wrench and 9/ 16” wrench, loosen both pivot bolts until
they can be turned by hand. Pivot #1 only requires a 9/ 16” wrench, as the
Allen nut side is welded in place.
2. Tighten pivot #1 until the handle is close to the desired “feel”.
3. Tighten pivot #2 until it just starts to increase the force required to move the
handle.
Pivot #1
Pivot #2
Fig. 42 — Joystick Adjustment
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Hydraulic System Maintenance
The hydraulic system consists of:
§ Blade Shaft
§ Hydraulic Pump
§ Transaxle
§ Depth Stop Cylinder & Valve
§ Hydraulic Manifold
§ Hydraulic Filter
§ Lift Cylinder
§ Oil Fill/ System Vent
Routine Maintenance
·
Check oil level daily.
·
·
Level the saw frame prior to service to get an accurate reading.
Fill reservoir to Fill line when cold, with 5W-30 premium grade engine oil.
Fig. 43 — Oil Reservoir Fill Line
·
Change oil and filter annually.
Oil Fill/System
Vent
Oil Cooler
Assembly
Depth Stop Cylinder
Lift Cylinder
Hydraulic Pump
Oil Filter
Fuel Filter
Transaxle
Hydraulic
Manifold
Blade Shaft
Fig. 44 — The Hydraulic System
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Draining & Filling the Hydraulic System
To drain the hydraulic system:
1. Remove the drain plug from the bottom of the Blade Shaft housing and the
bottom of the Transaxle.
Drain Plug
Drain Plug
Fig. 45 — Hydraulic System Drains
2. Collect and dispose of the used oil in an environmentally friendly manner.
3. Remove the used oil filter. See Fig. 44.
4. Once drained, reinstall the drain plugs.
5. Pre-fill and install a new oil filter.
To prevent hydraulic pump damage, pre-fill the filter with oil prior to
installing it.
CAUTION
61
Download from Www.Somanuals.com. All Manuals Search And Download.
To fill the hydraulic system:
1. Fully lower the saw.
2. Do not level the saw frame. The 4-Speed Blade Shaft is mounted at a 78° angle
to the saw frame. Adjust the level of the saw so that the face of the Blade Shaft
housing is at right angles to the ground.
Filler Plug
Housing Face
Collars will be approx. 6”
off the ground when
housing is perpendicular to
90
Ground
Level
the ground.
Sight Glass
Fig. 46 — Filling the Hydraulic System
If the saw is not leveled correctly, the 4-Speed Blade Shaft could be
damaged by operating with too little, or too much, oil.
CAUTION
3. Add oil to the fill port on top of the 4-Speed Blade Shaft Housing.
4. Start the engine, and run it for a couple minutes to spread the oil throughout
the system
·
·
Add more oil as required.
Repeat steps 3 & 4 as necessary.
5. When the 4-Speed Blade Shaft is full, and positioned at 90° to the ground, the
oil should show between the center and the top of the sight glass on the front of the
main housing.
6. Inspect for leaks after service.
If the Blade Shaft is drained completely, it will require approximately
1 gallon to refill. If the transaxle is drained as well, it will require
approximately one additional gallon.
!
NOTE
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Bleeding the Depth Stop Cylinder
After changing the hydraulic system oil, or after disturbing the Depth Stop
Cylinder plumbing, air may become trapped in the system and cause the Depth
Stop Cylinder to work improperly. To remedy the situation, the Depth Stop
Cylinder must be bled to remove trapped air. This procedure requires the use of
the Depth Stop Block tool (P/ N 584042)..
1. Open the Depth Stop Valve.
2. Fully raise the saw.
3. Place the Depth Stop Block between the Depth Stop Plate and the Front
Axle.
4. Fully lower the saw.
·
Verify that the Depth Stop Cylinder has fully collapsed.
5. With the Depth Stop Valve still open, and the engine running:
·
·
At the rear of the cylinder use a 1/ 8” diameter hose on the bleeder nipple.
Use the length of hose to direct the flow of oil into a suitable receptacle.
Open the bleeder valve at the rear of the cylinder and allow the oil to flow
until no air is detected in the fluid. Close the bleeder valve.
Tighten the hose connection.
·
·
Dispose of the waste oil in an environmentally-friendly manner.
6. Remove the Depth Stop Block and test the operation of the Depth Stop.
7. Re-fill the Reservoir Fill bottle at the rear of the Fuel Tank.
Depth Stop
Block tool
Depth Stop Block
tool in place
Fig. 47 — Bleeding the Depth Stop Cylinder
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Drive Wheel Alignment
Below is the technique recommended for aligning the wheels. Distance X is the
same on both sides; the Front Wheel and Blade shaft axles must be at right angles
to the frame edge. Distance A is 3/ 16” (.187”) longer on the right side, so that the
saw steers slightly left. Users may wish to alter the alignment to fit a particular
application.
Distance X
Distance A
Distance X
Distance = A + .187”
Fig. 48 — Drive Wheel Alignment
64
Download from Www.Somanuals.com. All Manuals Search And Download.
The drive wheels are aligned by adjusting the entire rear drive assembly:
1. Loosen the Transaxle Attachment Bolts just enough to move the Transaxle
— do not completely loosen the bolts.
2. Loosen and tighten the Alignment Jackscrew nuts to move the Transaxle
— and thus the wheels — in the appropriate direction to achieve the
desired alignment distance (see Fig.46).
3. Lock down the Transaxle Attachment Bolts when the appropriate
alignment distance is set.
Pivot Side
|
Adjustment Side
Alignment
Jackscrew
Adjustment Side
Attachment Bolts
Pivot Side
Attachment Bolts
Fig. 49 — Drive Wheel Alignment Bolt Locations
65
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
57 HP Turbocharged Deutz Diesel, direct injection, air/ oil cooling, oil filter and
above-frame remote oil drain.
Engine
Engine Air Cleaner
Fuel Tank
4-Stage air filtration, pre-cleaner plus cartridge element and safety element.
10 Gallon clear-molded plastic fuel tank with sight gauge, central drain and
shutoff valve.
Fully enclosed transmission, bearings and shaft, oil bath lubrication with cooled
and filtered oil circulation system, 4 protected shaft seals, 2-3/ 8” diameter blade
shaft, rack & pinion shifting, positive shift lock, oil sight gauge, magnetic drain
plug, easy serviceability, remote protected oil fill and vent, blade usable on either
side of saw, taper lock blade collar attachment, standard blade shaft tachometer,
ratios of 1:1, 1.34:1, 1.7:1, and 2.02:1
Blade Shaft Assembly
Blade Collars
Plated quick-disconnect, taper lock attachment, 5.5” diam., 24 water spray ports.
Minimum water usage system, evenly distributed across the blade, panel-
mounted flow control.
Blade Flushing
Blade Range
14” to 48”.
21”.
Max Cut Depth
Extra heavy design, slip-on type with double lip seal and quick disconnect water
hose, two handles.
Blade Guard
Blade Shaft Drive Belt
Blade Control
Dual 5--Groove premium quality Goodyear HY-T Wedge Torque Team belts.
12-Volt hydraulic raise/ lower system, 3 blade plunge speeds, fast and slow blade
plunge speed buttons on joystick, raise button on joystick, one-hand control.
Blade Depth Stop
Balance
Positive, heavy-duty hydraulically controlled depth stop.
Front steer.
Handlebars
3-Position adjustable angle, storage position, quick locks.
8” x 3”, precision sealed bearings in each wheel with extra end seals and seal
protectors, no grease points.
Front Wheels
Rear Wheels
12” x 3”.
Hydrostatic powered transaxle with infinite speed control, joystick control, remote
oil filter and up to 300 feet per minute travel speed. Locked axle drive.
Drive System
Twist-lock throttle, backlit tachometer with hour meter, voltmeter, oil pressure
gauge and 3-position ignition switch.
Engine Controls
Battery
12-Volt, group 75, 1000 cold cranking amps.
Heavy gauge steel, 6” pointer wheel and plastic-coated tether.
Standard, adjustable.
Front Pointer
Rear Pointer
Hardware
Tools
Grade 8 fasteners throughout.
15/ 16” Blade wrench.
L= 47-1/ 2” with handlebars stored, W = 32” w/ o blade collars, H= 44” with front
pointer up.
Dimensions
Weight
1,700 Pounds, with oil but no fuel.
Serviceability
Spin-on oil filters, lubrication points, lube every 50 hours.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
D
A
B
C
Max Length, Handle Bar
Extended, Pointer Bar Up
Max Length, Handle Bar
Removed, Pointer Bar Up
Max Height, Console Top to
Surface
A
B
C
D
71”
50 3/ 8”
33 ½”
115”
E
Max Length, Handle Bar
Extended, Pointer Bar Down
Max Height
E
F
52 ¾”
19 ¾”
28”
Wheel Base, Front Wheels
Wheel Base, Rear Wheels
Max Width, Guards, Covers
OFF
G
H
35”
F
G
Max Width, Guards, Covers
ON
H
I
36 ½”
I
J
J
(with Collars & Guards OFF) 32 ½”
K
K Wheel Path (per side)
4.0”
Crated Dimensions: 60” x 60” x 61”
Crated Weight - 1 Blade Guard 1800 lbs.
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-6457 Electric Diagram
All Wire 18 Gauge Unless Noted: Ground Wires Are Black
10-
8-Ground
6-
-9
Fuel Rack-7
-5
8 Gauge
SOLENOID
/RELAY
BROWN
GREY/WHT
RED
Oil Pressure
4-Temperature
2-D+
-3
Tachometer-1
VIOLET/ORN
EMERGENCY
STOP
BLK/RED
GLOW
PLUG
IN2
IN1
IN4
IN3
GEN
IN5
8
8
4
3
4
3
WHITE
+
-
+
-
+
-
VOLTAGE
TACH
TACH
LOFA
AIR
SIG
MAG
KL 31
KL 50
FILTER
SWITCH
B
B
B
B
B
STOP
KL 15
S
B
AUX
LIGHT
GREY
YELLOW
SWITCH
SWITCH
STARTER
LINE
OUT
GREEN
CB3
LINE
IN
YL/BLK
RED
RED
2-PIN
PACKARD
BLUE/WHT
WATER
PUMP
SWITCH
A
SPOT
LIGHT
R
S
F
F-N-R
CONTROL
LINE
OUT
LINE
IN
LINE
IN
B
4-PIN
TRAILER
PLUG
CB2
CB1
LINE
OUT
LINE
OUT
4-PIN
PACKARD
A
B
C
D
1N4007
GREEN/BLK
RED/YL
+
RED
+
FENNER
POWER
UNIT
IGNITION SWITCH
A
A
D
D
C
C
B
B
MANIFOLD
CONNECTOR
2-PIN
PACKARD
4-PIN
PACKARD
B
A
1N4007
1N4007
HYDRAULIC
MANIFOLD
VALVES
WATER
PUMP
BATTERY
SLOW
LOWER
SV2
FAST
LOWER
SV1
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX: 310-537-3927
E-MAIL: mq@multiquip.com
www: multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR •
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Miele Washer G 7804 User Manual
Network Technologies Switch ST nXm U User Manual
NordicTrack Home Gym NTSY98970 User Manual
N Tron Switch 526FX2 A User Manual
Olympus Camera Accessories PT 026 User Manual
Omnimount TV Mount 100 W C User Manual
Optoma Technology Projector EP739 User Manual
Panasonic Answering Machine KX TG5664 User Manual
Panasonic Car Video System CY VH9300U User Manual
Panasonic TV Converter Box AJ FRC27E User Manual