PARTS AND OPERATION MANUAL
CONCRETE SAW
MODELS FS2 & FS2SP
Revision #2 (06/26/06)
MULTIQUIPINC.
18910 WILMINGTON AVE.
PARTS DEPARTMENT:
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700
800-421-1244
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
800-478-1244
FAX:310-537-3927
FAX:310-631-5032
E-mail:mq@multiquip.com • www:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Montreal, Canada • Manchester, UK
Rio De Janiero, Brazil • Guadalajara, Mexico
P/N 25248
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE
800-478-1244 or 310-537-3700
FAX: 310-537-4259
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310-537-1173
MAIN
800-421-1244 or 310-537-3700
FAX: 310-537-3927
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Here's How To Get Help ........................................... 3
Table Of Contents .................................................... 4
Parts Ordering Procedures ...................................... 5
Safety Message Alert Symbols .............................6-7
Decals ...................................................................... 8
Rules for Safe Operation ....................................9-11
Dimensions ............................................................ 12
Weights .................................................................. 13
Basic Components ............................................14-15
Console Components ............................................ 16
Basic Engine Components..................................... 17
General Information ..........................................18-19
Engine Mount Assembly ...................................48-49
Pointers And Covers .........................................50-51
Water System Assembly ...................................52-53
Basic Platform Assembly ..................................54-55
Blade Guard 14-Inch Assembly ........................56-57
Blade Guard 20-Inch Assembly ........................58-59
Manual Raise and Lower Assembly .................60-61
Plug Kit (Push) Assembly..................................62-63
Plug Kit (Self-Propelled) Assembly ...................64-65
Battery Box Assembly .......................................66-67
Platform (Bare) Assembly .................................68-69
Transmission Assembly.....................................70-71
Engines
Engine Assemblies............................................72-73
MQ-Whiteman — FS2/FS2SP
Concrete Saw
Wiring Diagram
Wiring Diagram (Engine/Console) ......................... 74
Wiring Diagram (Rocker Switches) ........................ 75
Inspection..........................................................20-21
Inspection Blade .................................................... 22
Inspection Blade Placement .................................. 23
Inspection-Guards, Covers, and V-Belts ...........24-25
Initial Start-Up ...................................................26-27
Operation ..........................................................28-29
Maintenance .....................................................30-33
Troubleshooting (Engine)..................................34-35
Troubleshooting (Blade) ......................................... 36
Explanation Of Codes In Remarks Column ........... 38
Suggested Spare Parts .......................................... 39
Nameplate And Decals .....................................40-41
Under Carriage Assembly.................................42-43
Rear Axle Assembly ..........................................44-45
Blade Shaft Assembly .......................................46-47
Terms and Conditions Of Sale — Parts ................. 76
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective:June 1st, 2005
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only)
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!
:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
■
■
■
View Parts Diagrams
Order Parts
PrintSpecificationInformation
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Gotowww.multiquip.comandclickon
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 3% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
Order via Phone:
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
✓
Fed Ex/UPS
✓ DHL
Dealer Name and Address
■
■
Priority One
Ground
✓
Truck
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
■ Next Day
■
Second/ThirdDay
Quantity, Part Number and Description of Each Part
Unless otherwise indicated by customer, all orders are treated asStandard Orders and will ship
within24hours.WewillmakeeveryefforttoshipAirShipmentsthesamedaytheorderisreceived,
if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
NOTE
WE ACCEPT ALL MAJOR CREDIT CARDS!
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all times when
operating this equipment. Failure to read and understand the
Safety Messages and Operating Instructions could result in
injury to yourself and others.
Lethal Exhaust Gases
Engine exhaust gases contain poisonous
NOTE
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
This Owner's Manual has been developed to provide
complete instructions for the safe and efficient operation
of the MQWhiteman FS2 and FS2SP Concrete Saws.
Depending on the power plant you have selected, please
refer to the engine manufacturers instructions for data
relative to its safe operations.
Before using this Concrete Saw, ensure that the
operating individual has read and understands all
instructions in this manual.
Explosive Fuel
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
Burn Hazards
DANGER: You WILL be KILLED or
SERIOUSLY injured if you do not follow
directions.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. Never operate the engine with heat
shields or heat guards removed.
WARNING: You CAN be KILLED or
SERIOUSLY injured if you do not follow
directions.
Rotating Parts
CAUTION: You CAN be injured if you
do not follow directions.
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair and
clothing away from all moving parts to prevent
injury.
Potential hazards associated with Concrete Saw operations
will be referenced with Hazard Symbols which appear
throughout this manual, and will be referenced in conjunction
with Safety Message Alert Symbols.
PAGE 6 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
Respiratory Hazard
ALWAYS place the ON/OFF switch in the OFF
position, remove key and/or disconnect the
spark plug lead before servicing the engine
or equipment. Ground the lead to prevent
sparks that could ignite a fire.
ALWAYS wear approved respiratory
protection.
Over Speed Conditions
Sight and Hearing hazard
NEVER tamper with the factory settings of the
engine governor or settings. Personal injury
and damage to the engine or equipment can
result if operating in speed ranges above
maximum allowable.
ALWAYS wear approved eye and hearing
protection.
Guards and Covers In Place
Equipment Damage Messages
Other important messages are provided throughout this manual
to help prevent damage to your concrete saw, other property, or
the surrounding environment.
NEVER operate the saw without blade guards
and covers in place. Adhere to safety guidelines
ANSI American National Standards Institute,
OSHA or other applicable local regulations.
NOTE
This concrete saw, other property, or the
surrounding environment could be damaged
if you do not follow instructions.
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — DECALS
Machine Safety Decals
The FS2 and FS2SP Series concrete saws are equipped with a number of safety decals (Figure 1). These decals are provided for operator
safety and maintenance information. The illustration below shows these decals as they appear on either concrete saw. Should any of these
decals become unreadable, replacements can be obtained from you dealer. See pages 40 and 41 for decal placement.
Figure 1. FS2/FS2SP Decals
PAGE 8 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust manifold, muffler or cylinder. Allow
these parts to cool before
servicing engine or saw.
WARNING:
Failure to follow instructions in this manual may
lead to serious injury or even death! This
equipment is to be operated by trained and
qualified personnel only!This equipment is for
industrial use only.
The following safety guidelines should always be used when
operating the MQ Whiteman FS2 or FS2SP Concrete Saws:
■
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot components can cause serious burns.
GENERAL SAFETY
■
DO NOT operate or service this equipment
beforereadingthisentiremanual.
The engine section of this saw requires an adequate free flow
of cooling air. NEVER operate the saw in any enclosed or
narrow area where free flow of the air is
restricted. If the air flow is restricted it
will cause serious damage to the saw
or engine and may cause injury to
people. Remember the saw's engine
gives off DEADLY carbon monoxide
gas.
■
■
This equipment should not be operated by persons under 18
years of age.
NEVER operate this equipment without proper
protective clothing, shatterproof glasses, steel-
toed boots and other protective devices required
by the job.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
ALWAYS use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or explosion
could result from fuel vapors, or if fuel is
■
■
NEVER operate this equipment when not
feelingwellduetofatigue, illnessor taking
medicine.
spilled on a hot engine.
■
NEVER operate the saw in an explosive
atmosphere or near combustible materials.
An explosion or fire could result causing
severe bodily harm or even death.
NEVER operate this equipment under the
influence or drugs or alcohol.
■
■
Topping-off to the fuel filler port is dangerous, as it tends to
spill fuel.
■
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
NEVER use fuel as a cleaning agent.
■
■
■
The manufacturer does not assume responsibility for any
accident due to equipment modifications.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult to read.
ALWAYS check the machine for loosened threads or bolts
before starting.
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — RULES FOR SAFE OPERATION
GENERAL SAFETY
DIAMOND BLADE SAFETY
■
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
■
Use appropriate steel centered diamond blades manufactured
for use on concrete saws.
■
ALWAYS be sure the operator is familiar with proper safety
precautions and operating techniques before using the saw.
■
ALWAYS inspect diamond blades before each use. The blade
should exhibit no cracks, dings, or flaws in the steel centered
core and/or rim. Center (arbor) hole must be undamaged and
true.
■
■
■
Stop the engine when leaving the saw unattended.
Block the unit when leaving or when using on a slope.
■
Examine blade flanges for damage, excessive wear and
cleanliness before mounting blade. Blade should fit snugly on
the shaft and against the inside/outside blade flanges.
Maintain this equipment in a safe operating condition at all
times.
■
■
■
■
ALWAYS stop the engine before servicing, adding fuel and
oil.
■
■
Ensure that the blade is marked with an operating speed greater
than the blade shaft speed of the saw.
NEVER Run engine without air filter. Severe engine damage
may occur.
Only cut the material that is specified by the diamond blade.
Readthespecificationsofthediamondbladetoensuretheproper
tool has been matched to the material being cut.
ALWAYS service air cleaner frequently to prevent carburetor
malfunction.
■
■
ALWAYS keep blade guards in place. Exposure of the diamond
blade must not exceed 180 degrees.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
Ensure that the diamond blade does not come into contact with
the ground or surface during transportation. DO NOT drop the
diamond blade on ground or surface.
■
■
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■
■
The engine governor is designed to permit maximum engine
speed in a no-load condition. Speeds that exceed this limit may
cause the diamond blade to exceed the maximum safe allowable
speed.
NEVERoperatethissawinareasthatcontaincombustiblematerial
or fumes. Fire and/or explosions may result from errant sparks
from the equipment.
Ensure that the blade is mounted for proper operating direction.
WARNING:
SAWTRANSPORTATION SAFETY
■
DO NOT operate this equipment unless all
■
Use the lifting bail and appropriate lifting equipment to ensure
the safe movement of the saw.
guards and safety devices are attached and in
place.
■
■
■
DO NOT use the handle bars and/or front pointer as lifting points.
NEVER tow the saw behind a vehicle.
■
■
Caution must be exercised while servicing this equipment.
Rotating and moving parts can cause injury if contacted.
Ensure that both pointer bars are positioned appropriately to
minimize their exposure during transportation.
Keep all inexperienced and unauthorized people away from
the equipment at all times.
■
■
Safeguardagainstextremesawattitudesrelativetolevel. Engines
tippedtoextremeanglesmaycauseoiltogravitateintothecylinder
head making the engine difficult to start.
■
■
Unauthorized equipment modifications will void all warranties.
Test the ON/OFF switch before operating.The purpose of the
switch is to shut down the engine.
NEVER transport the saw with the blade mounted.
PAGE 10 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — RULES FOR SAFE OPERATION
Emergencies
ALWAYS know the location of the nearest fire extinguisher
■
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department. This information will be
invaluable in the case of an emergency.
Maintenance Safety
■
NEVER lubricate components or attempt service on a running
machine.
■
ALWAYS allow the machine a proper amount of time to cool
before servicing.
■
■
Keep the machinery in proper running condition.
Fix damage to the machine immediately and always replace
broken parts.
■
■
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
DO NOT use food or plastic containers to dispose of
hazardous waste.
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — DIMENSIONS
Figure 2. FS2/FS2SP Concrete Saw Dimensions
TABLE 1. DIMENSIONS
REFERENCE
LETTER
DESCRIPTION
Max Height (Handle Bars Fully Raised)
DIMENSION (MM)
A
B
C
D
E
F
G
H
I
44" (1118)
35" (889)
98" (2489)
70" (1778)
62" (1575)
25" (635)
14" (356)
15" (381)
16" (406)
25" (635)
Max Height (Handle Bars Fully Lowered)
Max Length (Handle Bars Fully Raised & Front Pointer Lowered)
Max Length (Handle Bars Fully Raised & Front Pointer Raised)
Max Length (Handle Bars Fully Lowered & Front Pointer Raised)
Max Handle Bar Width
Max Handle Bar Deflection
Front Wheel Base
Rear Wheel Base
J
Max Width
Crated Dimension (L x W x H) 47" (1194) x 30" (762) x 44" (1118)
PAGE 12 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — WEIGHTS
Figure 3. FS2/FS2SP Concrete Saw Weights
TABLE 2. WEIGHTS
DESCRIPTION
OPERATING
WEIGHT
Lbs. (kgs)
SAW
FS2-LE14
FS2-LE20
SAW, FS2, 14", PUSH, LESS ENGINE
190 (86)
195 (88)
265 (120)
270 (122)
265 (120)
270 (122)
270 (122)
275 (125)
270 (122)
275 (125)
280 (127)
285 (129)
290 (132)
295 (134)
305 (138)
310 (141)
320 (145)
330 (150)
30 (14)
SAW, FS2, 20", PUSH, LESS ENGINE
FS2-8K14
SAW, FS2, 14", PUSH, 8.5 HP KOHLER
SAW, FS2, 20", PUSH, 8.5 HP KOHLER
SAW, FS2, 14", PUSH, 9 HP HONDA
FS2-8K20
FS2-9H14
FS2-9H20
FS2-12K14
FS2-12K20
FS2-13H14
FS2-13H20
FS2-13HE14
FS2-13HE20
FS2
SAW, FS2, 20", PUSH, 9 HP HONDA
SAW, FS2, 14", PUSH, 12 HP KOHLER
SAW, FS2, 20", PUSH, 12 HP KOHLER
SAW, FS2, 14", PUSH, 13 HP HONDA
SAW, FS2, 20", PUSH, 13 HP HONDA
SAW, FS2, 14", PUSH, 13 HP HONDA ELECTRIC START
SAW, FS2, 20", PUSH, 13 HP HONDA ELECTRIC START
FS2SP-13H14 SAW, FS2SP, 14", SELF PROPELLED, 13 HP HONDA
FS2SP-13H20 SAW, FS2SP, 20", SELF PROPELLED, 13 HP HONDA
FS2SP-13HE14 SAW, FS2, 14", SELF PROPELLED, 13 HP HONDA, ELECTRIC START
FS2SP-13HE20 SAW, FS2, 20", SELF PROPELLED, 13 HP HONDA, ELECTRIC START
FS2SP-20HE14 SAW, FS2SP, 14", SELF PROPELLED, 20 HP HONDA, ELECTRIC START
FS2SP-20HE20 SAW, FS2SP, 20", SELF PROPELLED, 20 HP HONDA, ELECTRIC START
FS2SP
FS214-BG
FS220-BG
BLADE GUARD KIT 14" W/PULLEYS BELTS AND MIST MANIFOLD FOR 8-13 HP
BLADE GUARD KIT 20" W/PULLEYS AND BELTS FOR 8-13 HP
25 (11)
FS214-BG20HE BLADE GUARD KIT 14" W/PULLEYS BELTS AND MIST MANIFOLD FOR 20 HP
FS220-BG20HE BLADE GUARD KIT 20" W/PULLEYS BELTS FOR 20 HP
30 (14)
FS2/FS2SP
OPTIONS
35 (16)
FS-WT
FS-LT
WATER TANK ASSEMBLY
20 (9)
EXTERNAL LIGHT ASSEMBLY (ELECTRIC START ONLY)
EXTERNAL ELECTRIC WATER PUMP ASSEMBLY (ELECTRIC START ONLY)
10 (4.5)
FS-WP
10 (4.5)
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BASIC COMPONENTS
BASIC COMPONENTS
Figure 4. FS2/FS2SP Concrete Saw Basic Components
PAGE 14 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BASIC COMPONENTS
MAJOR COMPONENTS
NO
1
DESCRIPTION
PAGE
UNDER CARRIAGE ASSEMBLY
SEE PAGES 42-43
SEE PAGES 44-45
SEE PAGES 46-47
SEE PAGES 48-49
SEE PAGES 50-51
SEE PAGES 52-53
SEE PAGES 54-55
SEE PAGES 56-57
SEE PAGES 58-59
SEE PAGES 60-61
SEE PAGES 66-67
SEE PAGES 68-69
SEE PAGES 70-71
SEE PAGE 74
2
REAR AXLE
3
BLADE SHAFT ASSEMBLY
4
ENGINE MOUNT ASSEMBLY
5
POINTERS AND COVERS ASSEMBLIES
WATER SYSTEM ASSEMBLY
6
7
FS2/FS2SP BASIC PLATFORM ASSEMBLY
14-INCH BLADE GUARD ASSEMBLY
20-INCH BLADE GUARD ASSEMBLY
MANUAL RAISE/LOWER ASSEMBLY
BATTERY BOX ASSEMBLY (ELECTRIC START)
TRANSMISSION ASSEMBLY
8
8
9
10
11
12
13
GASOLINE ENGINE ASSEMBLIES
WIRING DIAGRAM
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — CONSOLE COMPONENTS
8.
Pump On Switch – Push top of rocker switch to provide
(ON) +12 VDC power to the external water pump. Push
bottom of rocker switch to remove (OFF) +12 VDC power
from water pump (electric start models).
Figure 5 displays the location of the various operational control
features of the FS2/FS2SP saw. Features are dependent on the
specificmodelsawselected.Thefunctionofeachconsolecomponent
or indicator is explained below:
9.
Digital Tachometer/Hourmeter – Indicates engine RPM
and number of hours (operation) saw has been in use.
1.
Emergency Stop Button – Push this stop button to stop
the engine. Also acts as a fast and secure way to stop the
engine in the event of an emergency.
10. Raise/Lower Crank Handle – Physically orients saw
(raises or lowers) depending on cranking direction (CW or
CCW). One full turn equals 3/8". Turning the handle
clockwise lowers the saw, turning the saw counter-
clockwise raises the saw. The raise/lower crank handle is
used in conjunction with the depth feed gauge.
2. Transmission Engage/Disengage Lever – Forward
locking position engages transmission. Rear Locking
position disengages transmission from rear axle and
permits "free wheeling" (self-propelled models Only).
3.
4.
5.
Water ON/OFF Valve – On position opens valve and
permits water to flow from source through saw water hose.
OFF position closes valve and halts the flow of water.
11. Start Button – A spring loaded button, that when pressed
actuates the engine start solenoid (electric start models
only).
Throttle Lever – Pull the lever to increase engine RPM.
Push lever to decrease engine RPM (electric start models
only).
12. Depth Feed Gauge – Indicates the blade cutting depth in
inches. To activate, first lower the blade via the crank
handle until the blade touches the cutting surface. Then
roll the depth feed dial until the face label reads zero.
Choke Lever – Pull lever to assist when starting a cold
engine. Push lever down after engine warms to disengage
choke (electric start models).
13. Forward/Reverse Speed Lever – Controls forward and
reverse speeds for self-propelled operation. Provides
positive neutral for engine start. ALWAYS place
transmission engage/disengage lever in the engage
position before setting speed lever (self-propelled models
only).
6.
AUX Switch (Rocker) – Auxiliary switch for future features
(electric start models).
7.
Light Switch – Push top of rocker switch to provide +12
VDC power (ON) to the external halogen light. Push bottom
of rocker switch to remove (OFF) +12 VDC power from
halogen light (electric start models).
14. Handle Bar Locking Knobs – Loosen or tighten these
two knobs when making adjustments to the handlebar(s).
Turn handle(s) counter-clockwise to loosen and
clockwise to tighten.
Figure 5. Console Components
PAGE 16 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BASIC ENGINE COMPONENTS
HONDA 13 HP engine shown.
Figure 6. Engine Controls and Components
INITIAL SERVICING
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
The engine (Figure 6) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
NOTE
WARNING
WARNING
Operating the engine without an air filter,
with a damaged air filter, or a filter in need of
replacement will allow dirt to enter the
engine, causing rapid engine wear.
Adding fuel to the tank should be accomplished only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel spill,
DO NOT attempt to start the engine until the fuel residue has been
completely wiped up, and the area surrounding the engine is dry.
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap (HONDA) to 0.6 - 0.7 mm (0.028 - 0.031
inch). Clean spark plug once a week.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
9. Muffler – Used to reduce noise and emissions.
WARNING
3. Engine ON/OFF Switch – ON position permits engine
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after operating. NEVER
operate the engine with the muffler removed.
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — GENERAL INFORMATION
A unique water plumbing system allows for independent orientation
of either fluted floodwater to the blade for wet cutting applications or
cones of aerosol mist (14" blade guard only) to diminish material
dust cutting in situations where minimal water usage is necessary.
Quick disconnect hose fittings are provided for quick and easy water
orientation.
FAMILIARIZATION
The MQ Whiteman FS2/FS2SP Series concrete saws are designed
for wet or dry cutting utilizing diamond blades. They have been
engineered for general, industrial and high production flat sawing
applications. The exceptional performance of these saws centers
around innovative features, top quality components, and committed
attention to state-of-the-art manufacturing.
Operator control of the saw is safely accomplished with adjustable
ergonomic handle bars, and a combination of conveniently oriented
items on the console such as: Raise/Lower Crank Handle,
Tachometer/Hourmeter, ON/OFFWaterValve, Depth Feed Gauge,
and Emergency Engine ON/OFF switch. Additionally, for electric
start and self-propelled models, the console also provides starting,
power control and forward/reverse controls.
The reinforced heavy gauge steel frame and chassis assembly has
been precisely jig welded to eliminate operational bending and/or
flex that would lead to diminished blade performance. Additionally,
the general weight-to-strength ratio design of the frame and chassis
assembly provides for optimum weight distribution to keep the blade
running true in the cut.
An innovative outboard blade shaft bearing assembly ensures
minimalflutterandshaftharmonicsprovidingthemostadvantageous
condition for a diamond blade at operating speeds. Heavy duty
front and rear axles, oversized reinforced wheels supported by roller
wheel bearings and locking collars, and industrial under carriage
assembly ensure accurate tracking and years of reliable use.
All MQWhiteman FS2/FS2SP saws are designed, engineered
and manufactured with strict adherence to American National
Standards Institute, Inc. (ANSI) guidelines B7.1 and B7.5.
POWER PLANTS
The FS2/FS2SP Series saws provides a variety of gasoline engine
choices (Table 3). Selection of a specific engine, and its capacity
measured in horsepower/torque, directly affects the performance of
the diamond blade.
The positive locking Raise/Lower screw feed system with accurate
depth gauge easily orients blade elevation, and will not permit blade
creep during cutting operations.
TheFS2/FS2SP seriessaws aregenerallyclassifiedintheindustry
as a "LOW to MEDIUM " horsepower saws. This classification is
particularly useful when selecting the proper diamond blade for an
application. Refer to the engine Owner's Manual for specific
instructions regarding engine operation and maintenance practices.
TABLE 3. POWER PLANTS
FUEL TANK
GAL. (Liters)
ENGINE MFR.
MODEL
HP
STARTING SYSTEM
AIR CLEANER
KOHLER
HONDA
KOHLER
HONDA
HONDA
KOHLER
COMMAND PA-951502
GX-270 K1QC9 (558300)
COMMAND PA-951502
GX-390 K1QC9
8.5
9
Manual
Manual
Manual
Electric
Electric
Electric
Cyclone Air Filtration
Cyclone Air Filtration
Cyclone Air Filtration
Cyclone Air Filtration
Dry Cannister
1.6 (6.1)
1.6 (6.1)
1.8 (6.8)
1.7 (6.4)
1.7 (6.4)
1.7 (6.4)
12
13
20
20
GX-620 TXF2 (5844000)
COMMAND CH-20
Dry Cannister
PAGE 18 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — GENERAL INFORMATION
A quick disconnect hose and blade guard are easily removed for
fast blade changes, and easily seats itself on the chassis bayonet
fitting. The blade guard may be oriented for left or right hand cutting.
See pages 54 and 56.
UNDER CARRIAGE SYSTEM
A jig welded heavy steel gauge under carriage assembly supports
the saw in tracking, pivoting and stabilization. A 3/4" diameter rear
axle supports two solid rubber (8" x 2-1/2" x 1") cast hub wheels with
roller bearings, grease fittings and locking collars. A 3/4" diameter
front axle supports two solid rubber (5" x 2" x 3/4") cast hub wheels
with roller bearings, grease fittings and locking collars. The assembly
pivots about two rocker blocks with bushings. See page 40.
WATER SYSTEM
All FS2 saws provide a water direction system to provide cooling
water to the diamond blade. This system consist of : a standard
"garden hose" valve that connects the water source (via hose) to the
saw, an ON/OFF console water switch, water hose with quick
disconnect manifold fittings, and either a 14" or 20" blade guard.
BLADE DRIVE SYSTEM
Both the 14" and 20" blade guards are designed with two 6" fluted
water tubes to direct floodwater to the diamond blade.The 14" blade
guardincorporatesanindependentwatermistingsystemthatutilizes
specifically positioned aerosol spray nozzles to support dust
suppression when sawing in minimal water environments.
An innovative blade shaft assembly has been specifically designed
to support the optimum distribution of torque from the engine shaft to
the blade shaft, and to ensure minimal vibratory conditions on the
tips of the shaft.
Balanced engine & blade shaft pulleys are connected to their
respective shafts, and four V-belts connect the engine pulley to the
blade shaft pulley. The 1- 1/4" diameter blade shaft is supported by
two self-aligning pillow block bearings that are uniquely positioned
on the most outboard portion of the reinforced frame.
The misting spray (approximately 5 gallons/hour) requires a 35-45
psi water pressure for effective results.
CONSOLE
An ergonomically designed control console allows the operator to
easily understand and/or operate the adjustable handlebars, Raise/
Lower Crank Handle, Tachometer/Hourmeter, ON/OFF Water
Valve, Depth Feed Gauge, and Emergency Engine ON/OFF Switch.
Additionally, for electric start and self-propelled models, the console
also provides starting, power control and forward/reverse controls.
The combination of pulley and blade shaft bearing positioning
ensures minimal vibration & flutter to the ends of the blade shaft.
The blade drive system has been designed for left and right hand
cutting. See page 44.
MECHANICAL RAISE/LOWER SYSTEM
BLADE GUARD ASSEMBLY
A positive locking mechanical raise and lower screw feed assembly
supports elevation cycling operations. A crank raise/lower handle
islocatedontheconsolewith"clockwise"rotationprovidinglowering
action, and "counter-clockwise" rotation providing raising action.
An ACME precision screw and thread assembly provide accurate
travel; while a spring loaded plunge ball system ensures positive
height position locking.
The FS2/FS2SP comes standard with either a 14" or 20" hinged
two-piece, heavy steel gauge blade guard.
Both blade guards provide zinc plated, fluted floodwater manifold
assemblies that supply optimum volume and dispersal of water to
both sides of the diamond blade for wet cutting. The sizable (6")
fluted floodwater tubes resist clogging and are easily removed for
maintenance.
An adjustable depth gauge assembly is synchronized with raise/
lower handle rotations to accurately depict depth feed.SeeTable 4
for blade selection with respect to depth of cut. Blade orientation is
referenced on the console's depth feed gauge.
The spray pattern and orientation, in conjunction with the design of
thebladeguard, providesexceptionaldustsuppressionwhencutting
dry, and may also be desired when the job site requires minimal use
ofwater.
TABLE 4. BLADE SELECTION
The 14" blade guard is designed with an independent aerosol
misting system to meet the challenges of minimal water sawing
operations.The spray pattern and orientation of the two removable
jet nozzles, in conjunction with the design of the 14" blade guard,
provides exceptional dust suppression.
Diamond Blade
Diameter (In.)
Depth of Cut
12"
14"
16"
18"
20"
3-5/8"
4-5/8"
5-5/8"
6-5/8"
7-5/8"
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — INSPECTION
HONDA 13 HP engine shown.
Before Starting
1. Read safety instructions at the beginning of manual.
2. Clean the SAW, removing dirt and dust, particularly the
engine cooling air inlet, carburetor and air cleaner.
3. Check theairfilterfor dirtanddust. Ifairfilterisdirty,replace
air filter with a new one as required.
Figure 8. Engine Oil Dipstick (Oil Level)
NOTE
4. Check carburetor for external dirt and dust. Clean with dry
compressedair.
5. Checkfasteningnutsandboltsfortightness.
Some engines used with the FS2/FS2SP
Series concrete saws have an oil Alert
System. This system will automatically
stop the engine in the event of low oil
level. ALWAYS be sure to check the
engine oil level prior to starting the engine.
Engine Oil Check
1. To check the engine oil level, place the saw on secure level
ground with the engine stopped, and the diamond blade
removed.
2. Remove the filler cap/dipstick from the engine oil filler hole
(Figure 7) and wipe it clean.
Table 5. Oil Type
Season
Temperature
25°C or Higher
25°C~10°C
Oil Type
Summer
Spring/Fall
Winter
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
HONDA 13 HP engine shown.
0°C or Lower
Figure 7. Engine Oil Dipstick (Removal)
Explosive Fuel
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
Gasoline Check
4. If the oil level is low (Figure 8), fill to the edge of the oil filler
holewiththerecommendedoiltype(Table5).Maximum oil
capacity is 400 cc.
1. Remove the gasoline cap located on top of fuel tank.
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish
with unleaded fuel.
NOTE
3. When refueling, be sure to use a strainer for filtration. DO
Reference manufacturer engine manual for
specific servicing instructions.
NOT top-off fuel. Wipe up any spilled fuel.
PAGE 20 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — INSPECTION
Battery - The 12-Volt DC battery (Figure 11) is shipped dry, and
will require a proper electrolyte level for operation (electric start
models only).
HydrostaticTransmission - An EATON® Model 7 hydrostatic
transmission (Figure 9) provides the power for the saw's
propulsion system.The transmission drives a sprocket that directly
connects the rear axle assembly via a drive chain.The "no load"
forward/reverse speeds are approximately 80 ft/min (FS2SP
models only).
Figure 11. Battery
When servicing of the battery is required perform the following:
z
z
z
A face shield and rubber gloves should be worn while
handling and servicing battery's electrolyte.
Disconnect battery terminal clamps, and remove the battery
from the saw when servicing is required.
DO NOT overfill the battery.
Figure 9. Hydrostatic Transmission
WARNING!
The transmission is factory filled with approved hydraulic fluid
that has a viscosity equivalent to SAE 20W-20. Should additional
servicing be required, the following hydraulic fluids are
recommended:
Electrolyte is an acid and must be handled with
caution. Servicing instructions from the
electrolyte manufacturer must always be
followed to ensure safety. Serious injury can
result from careless handling and non-
compliance to safety handling instructions.
z
z
z
z
General Motors Dextron B
Ford MM2C-33F
Ford M2C-41A
WARNING!
International harvester Hy-Tran Fluids
Overfilling the battery may cause the electrolyte to overflow
resulting in corrosion to nearby components. Immediately wash
off any spilled electrolyte (battery acid).
Additionally, when connecting the positive
(+) cable to the battery's positive (+)
terminal post, DO NOT allow contact of the
wrench or any metallic part to come in
contact with the battery's negative (-)
terminal post. This may result in an
electrical short circuit or an explosion.
Figure 10.Transmission Reservoir
NOTE
DO NOT over fill the fluid reservoir (Figure 10). Note
the level marks on the reservoir. It is essential to
reference the existing oil conditions (A) cold or
(B) hot prior to operating the saw. Overfilling the
transmission with hydraulic fluid may cause the seals
to rupture causing mechanical damage.
NOTE
Use only distilled water in the battery.Tap
water can reduce the operating life of the
battery.
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — INSPECTION -BLADE
4.
Directional Arrow – Check to ensure that the blade is
oriented properly on the blade shaft for sawing. Reference
the directional arrow in the blade and place it so the direction
of rotation “downcuts” with the turn of the shaft.
WARNING
Failure to thoroughly inspect the diamond blade (Figure 12) for
operational safety could result in damage to the blade, the saw,
and may cause injury to the user or others in the operating area.
5.
Diamond Segment or Rim – Ensure there are no cracks,
dings, or missing portions of the diamond segment/rim. DO
NOT use a blade that is missing a segment or a portion
of the rim. Damaged and/or missing segments/rims may
cause damage to your saw, and injury to the user or others
in the operating area.
6.
Specifications – Ensure that the blade specifications, size,
and diameter properly match up to the sawing operation.
Wet blades must have water to act as a coolant. Utilizing a
diamond blade not matched properly to the task may result
in poor performance and/or blade damage.
7.
Arbor Hole – It is essential that the arbor hole diameter
properly matches the blade, and that it is free from
distortions. Correct blade flanges (collars) must be used.
The inside face of the flanges must be clean & free of debris.
An out of round arbor condition will cause damage to the
blade and the saw.
8.
MAX RPM – This RPM reference is the maximum safe
operating speed for the blade selected. NEVER exceed
the max RPM on the diamond blade. Exceeding the MAX
RPM is dangerous, and may cause poor performance and
may damage the blade.
Figure 12. Diamond Blade
1. Drive Pin Hole – A commonly located hole on the diamond
blade core that prevents operational blade slippage
between the inner & outer blade flanges (collars). Inspect
the diameter of the hole to ensure there is no distortion,
and that a snug fit develops between the hole and drive
pin.
2.
Stress Relief Holes (Gullets) – Check the steel core for
cracks that may have propagated from the slots and/or
gullets. Cracks indicate extreme fatigue failure and if sawing
continues, catastrophic failure will occur.
3.
Edge Of The Steel Core – Check the diameter edge for
discoloration (blue oxidation) indicating an overheating
condition caused by insufficient cooling water/air.
Overheating of blades may lead to loss of core tension
and/or increase the possibility for blade failure. Check to
make sure the steel core’s width is uniform about the rim of
the blade, and not succumbing to an “under cutting”
condition brought about by highly abrasive material or
improper under cutting core protection.
PAGE 22 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — INSPECTION -BLADE PLACEMENT
NOTE
3.
Blade Nut Wrench – Remove the blade nut wrench (3)
from the tool holder and unscrew the blade shaft nut (right-
side). This nut loosens clockwise and tightens counter-
clockwise.
The following steps should be accomplished
before placing the diamond blade on the
blade shaft.
4.
Blade Nut – Remove the blade nut (4). For reassembly,
DO NOT over tighten the blade nut against the outer flange.
Tighten blade nut approximately 45-50 ft-lbs/62-69 N/m.
■
Set the engine ON/OFF switch to the OFF
position.
5.
Outside Blade Flange (Collar) – Ensure that the flange
face is clean and free of debris and is placed flush against
the diamond blade (7). Check that the drive pin goes through
the blade pin hole (6) and seats properly into the inner
flange (8).
■
■
Place the console ON/OFF button in the OFF position.
Raise the saw to a high position by cranking the Raise/Lower
handle in a counterclockwise direction.
6.
Blade Pin Hole – Align this hole with the drive pin hole on
the inner flange collar.
■
Use the Blade Nut Wrench & Blade Shaft Locking Wrench
stored on the front section of the console to install the diamond
blade.
7.
Diamond Blade – Ensure that the proper blade has been
selected for the job. Pay close attention to the directional
arrow on the blade, clockwise for right-side cutting,
counter-clockwise for left-side cutting. The arbor hole
of the blade must match the 1" arbor of the blade shaft.
■
Reference Figure 13 (Diamond Blade Placement) when
removing or installing the diamond blade.
1.
Blade Guard – Unscrew the guard security knob and
water hose quick disconnect fitting and remove blade guard
(1) from its bayonet fitting and set it beside the saw.
8.
Inner Flange Collar – This flange is fixed upon the blade
shaft, and is manufactured with a drive pin hole. The inside
surface of the flange must be free of debris and permit a
tight closure on the surface of the blade.
2.
Shaft Lock Tool – Remove the shaft lock tool (2) from
the tool holder and insert the pointed end through the front
of the saw frame into the machined hole in the blade shaft.
A conveniently placed opening on the front of the saw frame
permits the use of the shaft lock tool. This tool inhibits the
shaft from rotating when applying torque to the blade nut.
Figure 13. Diamond Blade Placement
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — INSPECTION -GUARDS, COVERS & BELTS
Guards and Covers Check
V-Belts and Covers
CAUTION:
WARNING
NEVER attempt to check the V-belt with the engine running
because severe injury can occur. Keep fingers, hands, hair and
clothing away from all moving parts.
NEVER operate the saw without blade guards and covers
(Figures 14, 15 and 16) in place. DO NOT operate with the
front of the blade guard raised. The blade exposure cannot
exceed 180 degrees during operations. Adhere to the safety
guidelines of the American National Standards Institute
(ANSI) B7.1 and B7.5.
V-belts Alignment andTensioning
This concrete saw is equipped with four premium V-belts that
have been aligned and tensioned by factory personnel. All four
V-belts MUST be installed for proper operation of the saw.Failure
to run the saw with less than four belts may damage the saw or
equipment.
Use the following procedure to check the alignment of V-belts:
1. RemovetheboltsthatsecuretheV-beltcover(Figure16)to
thesawframe.
Figure 14. Blade Guard
CHECK the following on the "blade guard":
■
■
■
Check to ensure the capacity of the blade guard matches the
diameter of your diamond blade.
Check that the guard seats firmly upon the bayonet fitting of
the saw frame.
Check that the spring tensioned front cover of the guard is
firmly seated with the rear section of the guard, and there are
no gaps.
■
■
Check the fit of the water hoses about the two water manifolds
(14" guard). NEVER lift the blade guard while cutting.
Figure 16. V-Belt Cover
2. Check uniform parallelism (Figure 17) of V-belts and pulley
Check that the flood water tubes and water jets are clear and
open. Test the water supply for pressure and flow (to both
sides of the blade) before sawing operations.
(sheaves).Useastraightedgeormachinists'ssquareagainst
both pulleys and adjust both pulleys until equally aligned.
CHECK the following on the "blade flange cover":
■
Check that the flange cover seats firmly upon the bayonet
fitting of the saw frame prior to operation.
■
This flange cover is to be in place when cutting from either the
right or left side of the saw.
Figure 15. Blade Flange Cover
Figure 17.V-Belt Parallelism
PAGE 24 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — INSPECTION -GUARDS, COVERS & BELTS
FS2/FS2SP CONCRETE SAW — INSPECTION -GUARDS, COVERS & BELTS
3. Check V-belt tension (Figure 18) by using a tensionmeter
5. IftheV-beltsbecomeswornorloose,replacethembyusing
(6.0 - 9.0 lbs.) against the inside belt at a mid point between
the followingV-belt part numbers listed in Table 6.
the two pulleys, or by deflecting the center belt at a mid point
3/8” (10 mm) - 1/2” (13 mm).
Table 6. V-Belts and Pulleys
Engine Size
V-Belt P/N
15082 (4)
13249 (4)
15897 (4)
15082 (4)
Pulley P/N
15420
Blade Size
14
20
14
20
8.5 -13 HP Engine
15421
15365
20 HP Engine
15366
Figure 18.V-BeltTension
4. DO NOT over or under tension the V-belts. Severe damage
can occur to the saw and engine crank shaft if the belts are
over tensioned. A decrease of power to the blade and poor
performance will result if the belts are under tensioned (loose
on pulleys).
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW— INITIAL START-UP
CAUTION:
NOTE
DO NOT attempt to operate the saw untiDl the
The CLOSED position of the choke lever enriches
the fuel mixture for starting a COLD engine.The
OPEN position provides the correct fuel mixture
for normal operation after starting, and for
restarting a warm engine.
Safety, General Information and Inspection
sections have been read and understood.
Depending on engine manufacturer, operating
steps may vary.See engine operating manual.
The following start-up procedure makes reference to a HONDA
13 HP Engine (Manual Start)
6. Place the Choke Lever (Figure 22) in the "OPEN" position
1. Ensure the diamond blade has been mounted correctly and
that it is raised above the surface you are about to saw.
2. Connect a hose (water source) to the water input port of the
saw (see page 50, item 2, Water System Assembly), and
test for adequate flood water [ 4 to 5 gallons per minute (15
to 19 LT/min)], and/or misting water [steady geometric aero-
sol spray at 40 psi].
3. Place the fuel valve lever(Figure 19) to the "ON" position.
Figure 22. Choke Lever
CAUTION:
Figure 19. Fuel Valve Lever
4. Place the Engine ON/OFF switch (Figure 20) in the "ON"
position.
The engine governor speed has been set at the factory. Changing
the governor speed could damage the blade and/or the saw.
7. Place the throttle lever (Figure 23) halfway between fast
and slow for starting. All sawing is done at full throttle. The
engine governor speed is factory set to ensure optimum
blade operating speeds.
Figure 20. Engine ON/Off Switch
5. PULL the Console Engine ON/OFF switch (Figure 21) to
the"PULL-ON"position.
Figure 23. Throttle Lever
Figure 21. Console Engine ON/Off Switch
PAGE 26 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — INITIAL START-UP
8. Grasp the starter grip (Figure 24) and slowly pull it out.The
Stopping the Engine
resistancebecomesthehardestatacertainposition,corre-
spondingtothecompressionpoint.Pullthestartergripbriskly
andsmoothlyforstarting.
NEVER stop the engine while the blade is in the cut, except for
extreme emergencies. A sudden stoppage of the engine at high
speed while in a cut could damage the blade and/or saw, and
may cause injury to the user or other in the operating area.
CAUTION:
1. Place the throttle lever (Figure 23) in the slow position, and
listen for the engine speed to decrease.
z
DO NOT pull the starter rope all the way
to the end.
2. Push the console engine ON/OFF switch (Figure 21) to the
“OFF” position.
z
DO NOT release the starter rope after
pulling. Allow it to rewind as soon as
possible.
3. Place the engine ON/OFF switch (Figure 20) to the “OFF”
position.
4. Place the fuel valve lever (Figure 19) to the “OFF” position.
Maneuvering The Saw
WARNING
The blade is spinning whenever the engine is running.
Figure 24. Starter Grip
Raise the blade high above the surface when maneuvering the
saw. Damage to the blade and/or saw may occur if the blade
strikes the pavement.
9. If the engine has started, slowly return the choke lever
(Figure 22) to the CLOSED position. If the engine has not
started repeat steps 1 through 5.
CAUTION:
10. Before the saw is placed into operation, run the engine for
several minutes. Check for fuel leaks, and noises that would
associate with a loose guard and/or covers.
z
NEVER stop the engine in the cut while
working at high speeds, except for
extreme emergencies.
11. All sawing is done at full throttle. Your engine governor has
been set at the factory to ensure an optimum speed setting.
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — OPERATION
Saw Alignment
CAUTION:
1. The FS2/FS2SP employs a front and rear pointer (Figure 25)
that has been precisely aligned with the diamond blade at the
factory. Referencing the figure below, accurate tracking is
accomplished by referencing the front and rear pointer tips
over the cut line. Precise saw direction is accomplished by
slight operator pressure against the handle bars.
ALWAYS saw in a straight line only. Serious
damage to the blade may occur if the saw is
twisted or forced to cut radius shapes.
6. Slowlylowerthediamondbladeontothecutlinebycranking
theRaise/Lowerhandleclockwise. Whentheblade“touches”
thecuttingsurface,“zero-out”thedepthfeedgauge (Figure
5,item12)byrollingthedepthwheeluntil“0”islinedupwith
theslipmark. Slowlycontinuetolowerthebladeintothecut
until the desired depth is achieved.
If the water supply to your blade is interrupted - STOP
sawing immediately.
7. Set the sawing depth and saw only as job conditions and
specificationsrequire. Deepsawingiswastefultothelifeof
the blade. The preferred method of sawing is to “step cut”
in increments of 2” (51 mm). Step cutting provides the
optimum opportunity for the blade to cut fast and last it’s
longest.
Figure 25. Saw Pointers (Front/Rear)
2. To reorient a pointer position, loosen the screw that secures
thepointerbartotheshaft, adjustasnecessary, andretighten
the screw.
8. The rotation of the blade creates a tendency for the saw to
slightlypullinaparticulardirection. Toensureastraightline
ofsawing,applypressureagainsttheappropriatehandlebar
asyouslowlyadvancethesawforward. DONOTforcethe
bladeintothecutanyfasterthanitsdesignedtendency
is effective cut and remove the material.
3. For operator comfort, ergonomically designed handle bars
adjust by loosening two clamping knobs (Figure 5, item 14),
and adjusts to the desired height. Tighten the knobs back
down when the desired height has been achieved.
Wet Saw Operation
For Misting Water Sawing:
WARNING
The Water Misting System is designed to suppress the dust
signature caused by dry sawing. The aerosol spray pattern and
blade guard design greatly diminish the amount of dust that is
created. The misting water also acts as an added coolant for the
blade(14" blade guard only).
The operator must wear the appropriate protective
equipment and clothing while engaged in sawing.
For wet sawing :
1. Ensure the proper DRY CUTTING Diamond Blade is se-
1. Connecthosefromwatersourcetothehosefittingconnec-
tion(seepage 50,item 2, WaterSystemAssembly)ofthe
saw. The source pressure should be approximately 30-40
psi.
lected for the job.
2. Connecthosefromwatersourcetothehosefittingconnec-
tion(seepage50, item2, WaterSystemAssembly)ofthe
saw. The source pressure should be approximately 30-40
psi.
2. Ensurethequickdisconnectwaterthosefittingisconnected
to the Floodwater manifold of the blade guard.
3. Ensurethequickdisconnectwaterhosefittingisconnected
totheMisting(bottom)manifoldofthebladeguard(14”only).
3. Turn water source on.
4. Select the“ON”position (waterValve on the saw console),
andensurethe properflowandrate(4-6gallons/minute)is
equally directed to both sides of the diamond blade.
4. Turn Water source on.
5. Turn the water valve on the saw console to the “ON ”
position, and ensure the proper spray is equally directed
inside the blade guard (approximately 30-45 psi water
source pressure is required).
5. Align the saw along the cut line utilizing the front and rear
pointers.
PAGE 28 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — OPERATION
3. Push the console engine ON/OFF button to the “OFF”
6. Align the saw along the cut line utilizing the front and rear
pointers.
position (Figure 5, item 1).
4. Set the engine ON/OFF switch to the “OFF” position
7. Slowlylowerthediamondbladeontothecutlinebycranking
theRaise/Lowerhandleclockwise. Whentheblade“touches”
thecuttingsurface,“zero-out”thedepthfeedgauge(Figure
5,item12)byrollingthedepthuntil“0”islinedupwiththeslip
mark. Slowlycontinuetolowerthebladeintothecutuntilthe
desireddepthisachieved.
(Figure 6, item 3).
5. Place the water valve (Figure 5, item 3) in the “OFF” position
(as required).
WARNING
8. Set the sawing depth and saw only as job conditions and
specificationsrequire. Deepsawingiswastefultothe lifeof
the blade and can negate the effectiveness of the water
misting system to suppress dust. The preferred method of
sawing is to “step cut” in increments of 2” (51 mm). Step
cuttingprovidestheoptimumopportunityforthebladetocut
fast and last it’s longest.
Engine components can generate extreme
heat.
Diamond Blades and Blade Speed
1. Diamond sawing consist of cutting WET (using water to cool
the blade) or DRY (using the circulating air to cool the blade).
2. Selecting the diamond blade type and grade defines how
9. The rotation of the blade creates a tendency for the saw to
slightlypullinaparticulardirection. Toensureastraightline
of sawing, apply pressure against the appropriate handle
barasyouslowlyadvancethesawforward. DONOTforce
the blade into the cut any faster than its designed
tendency is effective cut and remove the material.
the blade will perform both in cutting speed and blade life.
3. Selection of the proper diamond blade consists of:
z
z
z
z
z
z
Determining WET or DRY cutting
Material to be Cut
Type of Saw Being Used
WARNING
Horsepower of Saw
If the engine stalls for any reason during
sawing, raise the blade out of the cut
before restarting.
Hardness Characteristics of the Material
Performance Expectations
10. The operator must recognize and adhere to the optimum
speed that the saw advances while sawing. DO NOT force
the saw in the cut. Observe the engine tachometer from time
to time to get the feel for a smooth sawing pace relative to
RPM.
Blade Speed
1. A diamond blade’s performance is directly connected to
specific peripheral (rim) speeds.
2. The following shaft rotational speeds have been factory set
to ensure optimum blade performance.
11. Factors for sawing economy:
z
z
z
z
z
Type of Blade
z
z
FS2/FS2SP 14” Capacity-3,200 RPM.
FS2/FS2SP 20” Capacity-2,600 RPM.
Depth of Cut
Sawing Speed
Characteristics of the Material Being Cut
Wet or Dry Sawing
WARNING
Finishing A Cut
Operating saw blades at rotational speeds
greater than those specified by the manufac-
ture can cause blade damage, and may in-
jure the user or others in the operating area.
1. Raise the blade out of the cut by cranking the Raise/Lower
handle counter-clockwise (Figure 5, item 10). Raise the
bladehighenoughoutofthecuttoclearthesurfaceandallow
the saw to be maneuvered.
2. Move the engine throttle lever to the idle (SLOW) position
(Figure 20).
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — MAINTENANCE
4. ENGINE AIR FILTER: Clean air filter 2 to 3 times daily
CAUTION:
when DRY cutting.See Engine Owner’s Manual for detailed
General maintenance practices are crucial to
information.
the performance and longevity of your saw.The
extreme environments of sawing operations
require routine cleaning, lubrication, belt
tensioning, and inspection for wear and dam-
age
5. ENGINE TANK & STRAINER: Clean every year/or 300
hours.
6. FUEL LINE:Replace every two years/or as necessary.
7. SPARK PLUG:Clean/adjust every 6 months/or 100 hours.
Replace every year/ or 300 hours.
Bearing Lubrication Care
WARNING
There are seven (7) grease points for the FS2 Push Model saw,
and nine (9) grease points for the FS2SP Self-Propelled Model
saw.[Use only Premium Lithium 12 based Grease, conforming
to NLG1 Grade #2 consistency.]
The following procedures devoted to mainte-
nance can prevent serious saw damage or
malfunctioning. Before servicing or inspection,
ALWAYS park the saw on a level surface with
the blade removed, and the Console Engine ON/OFF switch &
Engine ON/OFF switch in “OFF” position.
1. Front Wheels (2): Grease daily, see page 42, item 8,
UndercarriageAssembly.
2. RearWheels (2):Grease daily, see page 44, item10, Rear
AxileAssembly.
WARNING
3. Blade Shaft Bearings (2): Grease daily, see page 46,
item1, Blade Shaft Assembly.
Some maintenance operations may require
the engine to be run. Ensure that the mainte-
nance area is well ventilated. Exhaust contains poisonous car-
bon monoxide gas that can cause of unconsciousness and may
result in DEATH.
4. Raise/Lower AdjustTube (1): Grease daily, see page 60,
item26, Raise/LowerAssembly.
5. Transmission Shaft Bearings (2): Grease weekly/or 25
hours,seepage70,item28,TransmissionAssembly(forself-
propelled models only).
General Engine Care
1. ENGINE CHECK: Check daily for any oil and/or fuel leakage,
thread nut & bolt tightness, and overall cleanliness.
2. ENGINE OIL:Check daily.Inspect with blade removed and
saw frame level on a level surface. Keep the oil clean, and
at the proper servicing level (Figure 8).DO NOT OVERFILL!
SAE 10W-30 of SG is recommended for general use.
NOTE
When cutting DRY, lubricate blade shaft bearings 2
to 3 times daily. The grease can provide an added
protective seal for the bearings.
3. ENGINE OIL CHANGE: Change engine oil the first month
or 20 hours of operation.Then every 3 months/or 50 HOURS
NOTE
ALWAYS dispose of used oil in a responsible
manner.Ensure that the disposition of all hazardous
waste is handled properly. Call your Recycling
Center for information about recycling engine oil.
PAGE 30 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — MAINTENANCE
General Transmission Care
AdjustV-Belt Alignment/Replacement Pulleys
All FS2SP Models utilize spline gear wheel design coupled
with an EATON Model 7 HydrostaticTransmission that provides
forward/reverse propulsion. The simple design of the system
keeps maintenance to a minimum.
TheV-belts and their respective pulleys have been professionally
aligned at the factory. If there is a requirement to remove/replace
or adjust the pulleys, proceed with the following instructions.
1. Select the proper sized pulley both in outside diameter and
arbor size. Use approved Multiquip parts to ensure the
component compatibility.
1. Transmission Reservoir Cup: Check every 8 hours
of operation. When the transmission is cold (A), check oil
level against the level indicator (see Figure 26).
2. AchangeinPulleydiametersmayrequirespecificallysized
V-Belts. Contact Multiquip Service Department to en-
sureV-Beltcompatibility.
DO NOT use multiple viscosity oils! DO NOT OVERFILL.
Complete DriveV-Belt(s) Replacement steps (1 through 7)
3. RemovetheV-BeltsfromaroundthePulley(s).
4. Removethesetscrewsthatsecurethepulleystotherespec-
tiveshafts(PTOshaft)forenginepulleyorthe(bladeshaft)
for the blade shaft pulley.
5. Remove/replace the pulley by sliding it off the shaft.
6. Reorient the new pulley on the shaft, and ensure precise
pulleyalignmentbyutilizinganaccuratestraightedge(see
Figures 27 and 28).
Figure 26. Transmission Reservoir
7. Replace/tightensetscrewstreatedwithadropofLOCTITE
2. Servicing: The transmission reservoir is factory filled.
Shouldservicingberequired,useSAE20W-20,APIclassi-
fication (SE,CC,CD) or better, General Motors Dexron B,
FordM2C-33F,M2C-41AorInternationalHarvesterHy-Tran
fluids. For extreme hot weather, drain oil and refill with an
oil having a viscosity of SAE30W-30 or SAE40W-40.
Threadlocker 266.
8. Orient the proper replacement V-Belt(s) around the blade
shaft pulley and engine pulley.
9. Reference the final stages of the DriveV-Belt(s) Replace-
m
3. Drive Chain: Check every 50 hours. Periodically wipe the
chain clean and relubricate with penetrating chain oil.
Thedrivechainmaystretchrequiringtensionadjustments.
Loosen the (3) transmission attachment screws (see page
68, item 11), and pivot the transmission in the“U”slots of
thetransmission mount untilthepropertensionisachieved.
(see page 68, item 33). EXCESSIVE TENSION ON THE
DRIVE CHAINWILL REDUCE CHAIN LIFE.
Figure 27. Pulley Alignment
4. SPLINEGEARWHEELS: Checkevery25hoursandclean
asnecessary. IfthesplinewheelsDONOTengagetherear
wheelswithsufficientpressure,slippageoftherearwheels
mayoccur.
To adjust the Spline Gear Assembly, place the transmis-
siondisengageleverintheDISENGAGEposition. Remove
therearconsolecover(seepage52,item19). Loosenthe
linkageadjustmentnutandslightlylengthenthelinkagerod
(see page 68, items 12 and 13). Recycle the transmission
ENGAGE/DISENGAGElevertoobservetheproperspline-
to-rearwheelcontact. Retightenadjustmentnutandreturn
Rear Console Cover.
Figure 28.V-Belt Alignment
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — MAINTENANCE
Blade Shaft Bearing Replacement
3. To loosen the tension on the four V-Belts perform the follow-
ing:
The FS2/FS2SP is supported by “tapped base lock collar (w/set
screw)’ self-aligning blade shaft bearings. These heavy duty
bearings support the 1-1/4 blade shaft, and have grease (zerk)
points (Figures 29 and 30) conveniently located for service.
z
z
z
Remove the Belt Guard, item, page 48, item 6 (Pointers
and Covers Assembly)
Loosen the Carriage Bolt, page 46, item 7 (Engine
Mount Assembly).
Loosen the Hex Head Cap Screws, page 46, item 4
(Engine Mount Assembly).
z
Rotate the engine down to provide slack in the V-Belts
Replacement of the Blade Shaft Bearings
4. Perform the following to replace the blade shaft bearings:
z
Remove blade flanges (page 44, items 7 and 8, Blade
Shaft Assembly) as required to permit the Shaft Bearing(s)
to slide off the blade shaft.
z
Loosen/remove shaft bearing(s) hex head cap screws,
page 44, item 11.
z
z
Loosen set screw on the blade shaft bearing collar.
Slide “old” bearing(s) off the blade shaft and replace with
“new” bearing(s)- grease (zerk) fitting pointing forward, and
the lock collar oriented to the “right" as you face the saw.
Figure 29. Right-Side Shaft Bearing
1. Reference pages 44 ( Blade Shaft Assembly) and
46 ( Engine Mount Assembly).
5. Looselyboltthebearing(s)intoplaceonthesawframe,then
ensurethealignmentbyreferencingpastbearingposition-
ing.
2. Its recommended to replace both left & right hand bearings
collectively.
6. Tighten the hex head cap screws, page 44, item 11 to
secure the shaft bearing (s) to the frame.
7. Tocompletethere-installationprocess,reversetheorderof
the above mentioned steps. For V-belt adjustment and
tensioningseepages31(Figures 27and 28)and33(Figure
32).
W — TRANSMISSION ASSY.
Figure 30. Left-Side Shaft Bearing
PAGE 32 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — MAINTENANCE
AdjustV-BeltTension
DriveV-Belt Check
Operating the saw with less than four (4)V-belts, or belts that are
slipping or are OverTensioned will significantly diminish the
performance of the saw, and may cause damage to the blade.
1. Tighten down the engine mount carriage bolt (page 46,
item 7,) and monitor the tension on the belts.
2. Determine the proper tension (Figure 32) by using a
tensionmeter against the inside belts at mid point between
thetwopulleys(6-9lbs.), orbydeflectingthecenterbeltsat
mid point 3/8” (10 mm) to 1/2” (13 mm).
1. TheV-BeltsoftheFS2/FS2SPhavebeenfactorysetutilizing
precisionstandards.
DriveV-Belt(s) Replacement
Reference Pointers and Covers Assembly (page 48), Blade Shaft
Assembly (page 44), Engine Mount Assembly (page 46) for this
operation.
1. Remove the Belt Guard (page 48, item 6), then loosen the
tensionoftheV-Belts
2. Loosen the Engine Mount Carriage Bolt (page 46, item 7).
3. Loosen the (4) 1 1/2” HHC screws (page 46, item 4).
4. Rotate the engine down to provide slack in theV-Belts.
5. Loosenthe(2)3/4”HHCscrewsthatsupporttheBladeShaft
Bearingsontheright-sideofthesaw(page44,item11,also
see Figure 31).
6. Removethe(2)3/4”HHCscrewsthatsecuretheBladeShaft
BearingontheV-Belt side ofthesaw(page44,item11, also
see Figure 31).
Figure 32. V-Belt Adjustment/Tension
3. Once the proper tension has been applied to the belts,
tighten the (4) 1-1/2” HHC screws (page 46, item 4).
4. Replace and secure the Belt Guard (page 48, item 6).
General Cleanliness
Figure 31.V-Belt Removal
Clean the machine daily. Remove all dust and slurry build up.
If the saw is steam cleaned, ensure that lubrication is accom-
plished AFTER steam cleaning operations.
7. Orientthebladeshaftsothebelt(s)tobereplacedcanslide
of the blade shaft pulley and engine pulley.
8. Select the proper Multiquip replacementV-Belts (see page
45, item12).
9. RemovethewornV-Belt(s).
10. Orient the proper replacement V-Belt(s) around the blade
shaft pulley and engine pulley.
11. Replaceandtightenthe(4)3/4”HHCscrewsthatsecurethe
Blade Shaft Bearings to the saw frame.
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — TROUBLESHOOTING (ENGINE)
TABLE 7. ENGINE TROUBLESHOOTING
SYMPTON
POSSIBLE CAUSE
SOLUTION
Check gap, insulation or
replace spark plug.
Spark plug bridging?
Carbon deposit on spark plug?
Clean or replace spark plug.
Difficult to start, "fuel is available, but no
SPARK at spark plug".
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
Set to proper gap.
Console or engine ON/OFF switch is
shorted?
Check switch wiring, replace
switch.
Ignition coil defective?
Replace ignition coil.
Set correct spark gap and
clean points.
Difficult to start, "fuel is available, and
SPARK is present at the spark plug".
Improper spark gap, points dirtry?
Condenser insulation worn or short
circuiting?
Replace condenser.
Replace defective spark plug
wiring.
Spark plug wire broken or short circuiting?
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Difficult to start, "fuel is available, spark
is present and compression is normal"
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Re-seat valves.
Suction/exhaust valve stuck or protruded?
Replace piston rings and or
piston.
Piston ring and/or cylinder worn?
Difficult to start, "fuel is available, spark
is present and compression is low"
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spark plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Apply lubricant to loosen fuel
cock lever, replace if necessary.
Fuel cock does not open properly?
No fuel present at carburetor.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Air in fuel line?
Clean or replace fuel tank cap.
Bleed fuel line.
PAGE 34 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — TROUBLESHOOTING (ENGINE)
TABLE 7. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTON
POSSIBLE CAUSE
Air cleaner not clean?
SOLUTION
Clean or replace air cleaner
Check float adjustment, re-build
carbureator.
Improper level in carburetor?
"Weak in power" compression is
proper and does not misfire.
Defective Spark plug?
Defective Spark plug?
Clean or replace spark plug.
Flush fuel system, and replace
with correct type of fuel.
Water in fuel system?
"Weak in power" compression is
proper but misfires.
Dirty spark plug?
Clean or replace spark plug.
Replace ignition coil.
Ignition coil defective?
Replace with correct type of
spark plug.
Spark plug heat value improper?
Engine overheats.
Correct type of fuel?
Replace with correct type of fuel
Clean cooling fins.
Cooling fins dirty?
Governor adjusted correctly?
Governor spring defective?
Adjust governor.
Replace governor spring.
Rotational speed fluctuates.
Recoil starter malfunction.
Check entire fuel system for
leaks or clogs.
Fuel flow restricted?
Recoil mechanism clogged with dust and Clean recoil assembly with soap
dirt?
and water.
Sprial spring loose?
Replace sprial spring.
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — TROUBLESHOOTING (BLADE)
TABLE 8. BLADE TROUBLESHOOTING
SYMPTON
POSSIBLE CAUSE
SOLUTION
Consult Dealer or Multiquip for correct blade. Try
cutting very soft material (sandstone, silica brick,
cinder block) to "Redress" the blade.
Blade too hard for the material being
cut.
Engine Torgue diminished because of
loose V-Belts.
Tighten and/or replace V-Belts.
Blade slows or Stops cutting,still
remains on blade.
Insufficent Engine power.
Check Throttle setting. Check Engine horespower.
Check that the blade is oriented, and rotational
arrow points in a "Down-Cutting" direction.
Improper direction of rotation.
Check that the blade & flange pin is properly
installed on the blade shaft (see Figure 10).
Blade is slipping on the blade shaft.
Blade being used on misaligned saw.
Check blade shaft bearings and alignment
integrity.
Check specifications of the blade with the
material being cut. Consult Dealer or Multiquip for
information.
Blade is excessively hard for the
material being cut.
Blade does not cut straight and/or
true.
Ensure blade surface feet per minute speed
(SFPM) is approximately 10,000 (see Page 29).
Blade being used at improper RPM.
Blade improperly mounted on arbor
shoulders and flanges.
Ensure blade is properly affixed on the blade
shaft.
Excessive force applied to blade while Do not force the blade in the cut. Apply a
cutting.
slow/steady pace to sawing..
Consult Dealer or Multiquip for correct blade. Try
cutting very soft material (sandstone, silica brick,
cinder block) to "Redress" the blade.
Blade too hard for the material being
cut.
Ensure blade is properly affixed on the blade
shaft. Ensure the blade flanges are clean & free
of debris.
Blade improperly mounted on arbor
shoulders and flanges.
Ensure proper flow & volume of water is provided
for wet cutting blades. Ensure sufficent cooling air
is circulated about a dry cutting blade.
Blade not receiving enough cooling
water or air.
Blade discoloring, crackling and/or
wearing excessively.
Ensure blade is properly affixed on the blade
shaft.
Abor hole out of round
Check specifications of the blade with the
material being cut. Consult Dealer or
multiquip for information.
Incorrect blade chosen for material
being cut.
Excessive force applied to blade while Do not force the blade in the cut. Apply a
cutting. slow/steady pace to sawing.
PAGE 36 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP SAW — EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts book.
Section 1: Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Section 2: Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial number
range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model number
or model number variant.
Section 3: Items Found In the“Items Number”Column
All parts with same symbol in the number column, , #,
, belong to the same assembly or kit.
+, %, or
*
■
Note: If more than one of the same reference number is listed,
the last one listed indicates newest (or latest) part available.
NOTE
The contents of this parts catalog are subject to
change without notice.
PAGE 38 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — SUGGESTED SPARE PARTS
FS2 CONCRETE SAW 1 TO 3 UNITS
1 to 3 Units
Qty......... P/N.............................. Description
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — NAME PLATE AND DECALS
NAME PLATE AND DECALS.
SEE DECAL ILLUSTRATIONS ON PAGE 8.
PAGE 40 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — NAME PLATE AND DECALS
NAME PLATE AND DECALS
NO
PART NO
15577
PART NAME
QTY.
REMARKS
1
DECAL: FS2 (WHITE)
2
2
1
1
1
1
*
2
15579
DECAL: MQ WHITEMAN 5.5" X 4"
DECAL: POWDER COATED
DECAL: WARNING PROP. 65
DECAL: WARNING RESPIRATORY
DECAL: WARNING BLADE GUARD
*
*
3
13118
4
15582
15580
15581
*
5
*
6
7
8
PLATE: SERIAL NO. .................................. 1 ......... CONTACT MQ SERVICE DEPT. W/MODEL & S/N
15741
15429
2942
DEPTH GAUGE LINEAR SCALE
CONSOLE
1
1
1
*
*
9
10
DECAL: MQ WHITEMAN 13"
11
15269
DECAL: KIT FS2 ......................................... 1 ......... INCLUDES ITEMS W/
*
SEE DECAL ILLUSTRATIONS ON PAGE 8.
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — UNDER CARRIAGE ASSY.
UNDER CARRIAGE ASSY.
1
1
1
6
6
5
7
3
2
7
4
10
LUBRICATION
POINT
8
NOTES:
USE LOCTITE 242 ON ITEM 1,
9
1
SCREW, HHC 3/8-16 X 1-1/4
PAGE 42 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — UNDER CARRIAGE ASSY.
UNDER CARRIAGE ASSY.
NO
1
PART NO
1023
PART NAME
QTY.
REMARKS
SCREW, HHC 3/8 - 16 X 1-1/ 4
SPACER, .88 X .64 X .35L
4
2
2
15020
15028
15090
15319
2079
3
SET COLLAR 5/8 DIA ..................................... 2 .......... INCLUDES ITEM W/
WHEEL, 5D X 2WX .6251D # 400 CAP
UNDERCARRIAGE W/A
*
4
2
1
2
4
2
2
5
6
ROCKER BLOCK, WITH BUSHING
WASHER, FLAT 5/8 SAE PLTD
ZERK FITTING
7
4684
8
2621
9
1162A
CAP, ZERK FITTING
10
SET SCREW
2
*
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — REAR AXLE ASSY.
REAR AXLE ASSY.
6
5
1
1
4
9
11
10
2
LUBRICATION
POINT
6 4
5
6
3
1
3
2
6
12
3
1
LUBRICATION
POINT
7
8
7
9
10
NOTES:
ITEMS ARE PLACED ON
INSIDE OF FRAME.
1
2
INCLUDED WITH SET COLLAR
ITEM 3.
INCLUDED WITH SET COLLAR
ITEM 7.
3
PAGE 44 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — REAR AXLE ASSY.
15313 (RAISE AXLE ASM )
NO
1
2
PART NO
15309
15310
PART NAME
WHEEL, 8.0 OD X 1.0 1D X 2.5W
AXLE, REAR
QTY.
2
1
REMARKS
3
15311
15312
15314
3264
COLLAR, SET 1.00 1.D................................... 2 .......... INCLUDES ITEM W/
*
4
SPACER, 1.0 X 0.44 PIPE, SCHED 40
BUSHING, FLG 1.25 OD X 1.00 1D X0.75
WASHER, FLAT 1" SAE
2
2
4
5
6
7
3615
COLLAR SET 3/4 ID ........................................ 2 .......... INCLUDES ITEM W/#
8
15376
1162A
2621
REAR POINTER W/A
ZERK FITTING CAP
ZERK FITTING
1
2
2
9
10
11
SET SCREW
SET SCREW
2
2
*
12#
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BLADE SHAFT ASSY.
BLADE SHAFT ASSY.
PAGE 46 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BLADE SHAFT ASSY.
BLADE SHAFT ASSY.
NO
1
PART NO
2621
PART NAME
QTY.
REMARKS
ZERK FITTING
2
2
2
1
1
2
2
1
1
4
4
2
1162A
15119
6059B
15065
15066
15063
15012
15093
0448
CAP, ZERK FITTING
3
KEY, WOODRUFF #91, ANS1 #8061
KEY, /4 SQ. X 2"
4
5
SHAFT, BLADE
6
BEARING, PILLOW BLOCK 1 1/4 BORE
FLANGE, BLADE INSIDE
FLANGE, DRIVEN ASSY.
NUT, 1-14-2B-LH
7
8
9
10
11
12
12
12
12
13
13
13
13
15
16
17
18
WASHER, FLAT 7 / 16 SAE
SCREW, HHC 7/16 -14 X 3/4
15563
15082
13249
15897
15082
15419
15421
15365
15366
15148
15092
1528
V-BELTS 3VX335 ........................................ 4 ........... 8.5-13 HP ENGINE HONDA 14" BLADE
V-BELTS 3VX315 ........................................ 4 ........... 8.5-13 HP ENGINE HONDA 20" BLADE
V-BELTS 3VX355 ........................................ 4 ........... 20 HP ENGINE HONDA 14" BLADE
V-BELTS 3VX335 ........................................ 4 ........... 20 HP ENGINE HONDA 20" BLADE
PULLEY, 1.25 HUB 4/3V4.50D .................... 1 ........... 8.5-13 HP ENGINE HONDA 14" BLADE
PULLEY, 4/3V3.00 X 1.000 ID/3L2.75.......... 1 ........... 8.5-13 HP ENGINE HONDA 20" BLADE
PULLEY, 4/3V4.12 X 1.125 ID/3L2.75.......... 1 ........... 20 HP ENGINE HONDA 14" BLADE
PULLEY, 4/3V3.00 X 1.125 ID/3L2.75.......... 1 ........... 20 HP ENGINE HONDA 20" BLADE
SPACER, 1.320D X 1.051D X 0.53
NUT, 1-14-2B
SCREW, SHS 1/4-20 X 5/16 HDP
WASHER, LOCK 7/16 MED
1
1
2
4
2955
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — ENGINE MOUNT ASSY.
ENGINE MOUNT ASSY.
2
1
4
3
8
1
3
5
6
7
6
ENGINE MOUNTING SLOTS
3
FOR:
20 HP HONDA (ELECTRIC START)
2
1
ENGINE MOUNTING SLOTS
FOR:
8.5 HP KOHLER (RECOIL START)
9.0 HP HONDA (RECOIL START)
12.0 HP KOHLER (RECOIL START)
13.0 HP HONDA (RECOIL START)
13.0 HP HONDA (ELECTRIC START)
PAGE 48 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — ENGINE MOUNT ASSY.
MOUNT ENGINE
NO
1
PART NO
0166A
0205
PART NAME
QTY.
REMARKS
WASHER, LOCK, 3/8 MED
SCREW, HHC 3/8 - 16 X 1
WASHER, FLAT 3/8 SAE
SCREW, HHC 3/8 - 16 X 1- 1/2
NUT, HEX FINISH 3/8 - 16
BAR THREADED
8
4
8
4
1
2
1
1
2
3
10136
1284
4
5
1456
6
15033
15174
15306
7
BOLT, CARRIAGE 3/8 - 16 X 3
MOUNT, ENGINE W/A
8
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — POINTERS AND COVERS ASSY.
POINTERS AND COVERS ASSY.
11
10
9
7
8
8
9
7
7
8
9
6
5
4
12
15
4
13
3
2
14
1
PAGE 50 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — POINTERS AND COVERS ASSY.
POINTERS AND COVERS ASSY.
NO
1
PART NO
15053
15052
15889
10133
9154
15248
0131A
0181B
0948
15088
1023
PART NAME
QTY.
1
REMARKS
WHEEL, POINTER ARM
ROD, POINTER
2
1
3
POINTER, LOMG FRONT, W / A
NUT, NYLOC 3/8 - 16
SCREW, HHC 3/8 - 16 X 1- 3/4
BELT GUARD W/A
SCREW, HHC 1/4 -20 X 3/4
WASHER, LOCK 1/4 MED.
WASHER,FLAT 1/4 SAE
COVER, BLADE FLANGE W / A
SCREW, HHC 3/8 - 16 X 1 - 1/4
SASH, POINTER RETAINER
SCREW, HHC 1/4 - 20 X 3/4
NUT, HEX FINISH 1/4 - 20
SLEEVE, SASH
1
4
2
5
2
6
1
7
4
8
4
9
4
10
11
12
13
14
15
1
1
15113
0131A
0949
1
1
1
15114
1
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — WATER SYSTEM ASSY.
WATER SYSTEM ASSY.
4
5
3/8 DIA. HOSE
16 IN. (41 CM.)
6
7
4
CONNECT
WATER SOURCE
HERE
4
3
2
1
5
3/8 DIA. HOSE
50 IN. (127 CM.)
9
BLADE GUARD
WATER MISTING
4
8
PAGE 52 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — WATER SYSTEM ASSY.
WATER SYSTEM ASSY.
NO
1
PART NO
15546
15076
15180
15538
15181
15766
15767
15768
15769
PART NAME
QTY.
REMARKS
GASKET, 3/4 HOSE GASKET / SCREEN
FITTING, STR 3/4 FEM HOSE X 1/2 MP
FITTING, DTR 6 BARB - 1/2 MP
CLAMP, WORM HOSE 7/16 - 11/16
HOSE 3/8 BLACK WATER 200 PSI
VALVE, 2 WAY 3/8 BARB X 3/8 MPT
FITTING, 6FPT - 6 BARB
1
1
1
4
2
3
4
5
5.5 FT.
6
1
1
1
1
7
8
FITTING, 6 BARB 3/4 MALE HOSE
FITTING, 3/4 HOSE QUICK REL FEMALE
9
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BASIC PLATFORM ASSY.
BASIC PLATFORM ASSY.
4
5
5
21
22
5
25
5
24
23
7
8
9
8
3
10
11
12
5
1
13
1
14
15
16
1
14
2
2
1
15
13
17
18
19
3
20
2
NOTES:
USE LOCTITE 271 ON ITEM 13,
SCREW, HHC 3/8-16 X 1
1
2
REFERENCE PAGES 66 AND 67
FOR COMPLETE PARTS BREAK-
DOWN FOR BARE PLATFORM ASSY.
P/N 15409.
PAGE 54 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BASIC PLATFORM ASSY.
BASIC PLATFORM ASSY.
NO
1
PART NO
11819
12287
11534
15701
15081
15702
15317
15503
15260
15097
15098
15138
15468
0205
PART NAME
QTY.
1
REMARKS
SCREW, HHC WASHER 1/4-20 X 3/4
SCREW, THP 1/4-20 X 3/4 SS
NUT U TYPE 1/4-20
2
1
3
6
4
HANDLEBAR, LEFT W / A
HANDLE GRIPS 1" DIA
HANDLEBAR, RIGHT W / A
CONSOLE W/A
KN0B, CONFORT GRIP
LIFTING BALE W/A
1
5
4
6
1
7
1
8
2
9
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
WRENCH, ALL PURPOSE
TOOL, SHAFT LOCK SOCKET W / A
WRENCH, 6" POCKET SOCKET
GROMMET 1.0 X 13 X 1.375
SCREW HHC 3/8-16 X 1
WASHER, LOCK 3/8 MED
WASHER, FLAT 3/8 SAE
NUT, NYLOC 1/4-20
1
1
1
2
8
0166A
10136
10024
29057
15280
15409
0131A
0181B
0948
8
4
4
DOCUMENT BOX
COVER, REAR
1
1
PLATFORM W/A ............................................ 1 ..................... SEE PAGES 66 AND 67
SCREW, HHC 1/4-20 X 3/4
WASHER, LOCK 1/4 MED
WASHER, FLAT 1/4 SAE
NUT U TYPE 1/4-20
3
3
3
3
1
11534
15424
COVER, PUMP MOTOR
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BLADE GUARD 14-INCH ASSY.
BLADE GUARD 14-INCH ASSY.
PAGE 56 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BLADE GUARD 14-INCH ASSY.
BLADE GUARD 14-INCH ASSY.
NO
1
PART NO
130A
PART NAME
QTY.
2
REMARKS
SCREW, SHS 1/4-20 X 1/4
SCREW, SHS 1/4-20 X 3/4
SCREW, SHS 1/4-20 X 1-1/4
SCREW, SHS 1/4-20 X 1
2
131A
2
3
0424
2
4
0730
2
5
0948
WASHER, FLAT 1/4 SAE
NUT, HEX FINISH 1/4-20
NUT, NYLOC 1/4-20
6
6
0949
4
7
10024
11505
15005
15043
15086
15096
15151
15161
15503
15504
15507
15508
15509
15562
15770
15842
15867
25023
26250
14
2
8
CLAMP, HOSE SUPPORT 1/2 INCH LG
GUARD, BLADE 14" BODY W/A
FLAP, NEOPRENE WATER SHIELD
NOZZLE, 5 GPH 80 DEG. SPRAY ANGLE
ANGLE, SPLASH GUARD
GUARD, BLADE 14" DOOR W/A
STOP, RUBBER BUMPER
KNOB, COMFORT GRIP
MANIFOLD (CIPSA)
GASKET, MANIFOLD FLOOD
PLUG (CIPSA)
SPRING, CENTURY SPRING
GASKET, MANIFOLD
9
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1
2
1
1
1
1
2
1
2
1
1
FITTING, 3/4 HOSE QUICK REL MALE
FITTING, 1/2 MP-3/4 F HOSE
TUBE, FLOOD 14"
PIN, HINGE 1/2 X 3.22
SCREW, HHC 1/4-20 X 1-3/4
2
2
2
1
8
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BLADE GUARD 20 -INCH ASSY.
BLADE GUARD 20-INCH ASSY.
PAGE 58 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BLADE GUARD 20 -INCH ASSY.
BLADE GUARD 20-INCH ASSY.
NO
1
PART NO
130A
PART NAME
QTY.
2
REMARKS
SCREW, SHS 1/4-20 X 1/4
SCREW, SHS 1/4-20 X 3/4
SCREW, SHS 1/4-20 X 1-1/4
SCREW, SHS 1/4-20 X 1
WASHER, FLAT 1/4 SAE
NUT, HEX FINISH 1/4-20
NUT, NYLOC 1/4-20
2
131A
2
3
0424
2
4
0730
2
5
0948
6
6
0949
4
7
10024
11505
15043
15096
15161
15462
15463
15503
15504
15506
15507
15508
15509
15770
15842
25023
26250
10
2
8
CLAMP, HOSE SUPPORT 1/2 INCH LG
FLAP, NEOPRENE WATER SHIELD
ANGLE, SPLASH GUARD
STOP, RUBBER BUMPER
GUARD, BLADE 20" BODY W/A
GUARD, BLADE 20" DOOR W/A
KNOB, COMFORT GRIP
MANIFOLD (CIPSA)
9
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
1
1
1
1
1
1
TUBE, FLOOD
GASKET, MANIFOLD FLOOD
PLUG (CIPSA)
2
1
2
SPRING, CENTURY SPRING
FITTING, 3/4 HOSE QUICK REL MALE
FITTING, 1/2 MP-3/4 F HOSE
PIN, HINGE 1/2 X 3.22
1
1
1
1
SCREW, HHC 1/4-20 X 1-3/4
4
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — MANUAL RAISE AND LOWER ASSY.
MANUAL RAISE AND LOWER ASSY.
9
5
8
1
6
11
1
28
2
20
27
1
21
4
7
3
13
4
14
23
1
2
4
12
7
22
15
16
19
LUBRICATION
POINT
26
10
8
17
NOTES:
WHEN ORDERING DEPTH GAUGE,
1
ITEM 20 P/N 15704, ALSO ORDER
LINEAR SCALE P/N 15741.
24
25
PAGE 60 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — MANUAL RAISE AND LOWER ASSY.
MANUAL RAISE AND LOWER ASSY.
NO
1
PART NO
0131A
0948
PART NAME
QTY.
8
REMARKS
SCREW, HHC 1/4 -20 X 3/4
WASHER, FLAT, 1/4 SAE
NUT, HEX FINISH 1/4- 20
NUT, NYLOC 1/4 - 20
2
12
1
3
0949
4
10024
10133
10136
11149
1456
9
5
NUT, NYLOC 3/8 - 20
WASHER, FLAT 3/8 SAE
BEARING, SB-204-12
NUT, HEX FINISH 3/8-16
KNOB, 3/8 - 16 X 2, 1" OD, 3.88L
PLUNGE, BALL
1
6
1
7
2
8
1
9
15050
15054
15089
15170
15188
15189
15238
15239
15290
15294
15336
15704
15708
15717
15738
19988
2219
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
1
SPACER, DEPTH ADJUSTER
FLANGE, BEARING 47-3- MFM
FLANGE, BEARING 47-3- MFM, MOD
FLANGE, BEARING SUPPORT
U- JOINT
1
1
1
1
1
PIN SPRING 0.1875 X 1.00 HARDENED
RAISE / LOWER W/A
2
1
HANDLE, W / A
1
SCREW, ACME, LEFT HAND
1
GAUGE, DEPTH ................................................. 1 ....... ORDER LINEAR SCALE P/N 15741
BRACKET, DEPTH GAUGE
1
1
1
1
1
1
1
SPRING, EXTENSION 5L X 0.25D X .0388
CABLE ASM, DEPTH GAUGE
PIN, CLEVIS 1/2 X 1.75 EFF
PIN, COTTER 1/8 X 1-1/2
ZERK, GREASE STR 1/4 - 28
SCREW, HHC 1/4 - 20 X 2-1/4 GRD 8
2621
26385
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — PLUG KIT (PUSH) ASSY.
PLUG KIT (PUSH) ASSY.
PAGE 62 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — PLUG KIT (PUSH) ASSY.
PLUG KIT (PUSH) ASSY.
NO
1
PART NO
0916
PART NAME
QTY. REMARKS
SCREW, HHC RHM 1/4-20 X 3/4
WASHER, FLAT
8
8
8
1
1
8
1
1
1
3
2
0948
3
10024
15208
15339
15340
15341
15342
15345
15553
NUT, NYLOC 1/4-20
4
COVER, PROPEL LEVEL FS2
COVER, FS2 ENGAGE HOLE
PLUG, 0.65 DIA X 14 GA, BLACK
PLUG, 0.44 DIA X 14 GA, BLACK
PLUG, 0.38 DIA X 14 GA, BLACK
PLUG, 0.28 DIA X 14 GA, BLACK
SWITCH, BLANK
5
6
7
8
9
10
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — PLUG KIT (SELF PROPPELLED) ASSY.
PLUG KIT (SELF PROPELLED) ASSY.
PAGE 64 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — PLUG KIT (SELF PROPPELLED) ASSY.
PLUG KIT (SELF PROPELLED) ASSY.
NO
1
PART NO
0916
PART NAME
QTY. REMARKS
SCREW, HHC RHM 1/4-20 X 3/4
WASHER, FLAT
2
2
2
8
1
1
1
3
2
0948
3
10024
15340
15341
15342
15345
15553
NUT, NYLOC 1/4-20
4
PLUG, 0.65 DIA X 14 GA, BLACK
PLUG, 0.44 DIA X 14 GA, BLACK
PLUG, 0.38 DIA X 14 GA, BLACK
PLUG, 0.28 DIA X 14 GA, BLACK
SWITCH, BLANK
5
6
7
8
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BATTERY BOX ASSY.
BATTERY BOX ASSY.
6
4
3
2
5
8
7
1
9
PAGE 66 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — BATTERY BOX ASSY.
BATTERY BOX ASSY.
NO
1
PART NO
0131A
0181B
0948
PART NAME
QTY. REMARKS
SCREW, HHC 1/4-20 X 3/4
WASHER, LOCK 1/4 MED
WASHER, FLAT 1/4 SAE
NUT, NYLOC 1/4-20
SCREW, THP 1/4-20 X 3/4 SS
U-BOLT 1/4-20 THREAD
BOX, BATTERY
1
5
4
4
4
1
1
1
2
2
3
4
10024
12287
15237
15273
4671
5
6
7
8
BATTERY, GR. UI WET W/TAG
NUT
9
XXXX
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — PLATFORM (BARE) ASSY.
PLATFORM (BARE) ASSY.
PAGE 68 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — PLATFORM (BARE) ASSY.
PLATFORM (BARE) ASSY.
NO
1
PART NO
15035
15069
15296
15303
15308
15453
15455
15666
15672
20530
PART NAME
QTY. REMARKS
MOUNT, BLADE GUARD BAYONET
MOUNT, FRONT POINTER
MOUNT, ENGINE/TRANS SIDE
PLATFORM
4
4
2
1
2
1
1
4
1
9
2
3
4
5
SUPPORT, REAR AXLE
PLATE, MOUNT, BELT COVER
TAB, SPRING IDLER
NUT, WELD 1/4-20, SQ NP
TAB, IDLER MOUNT
NUT, WELD, HEX LOCK 3/8-16
6
7
8
9
10
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — TRANSMISSION ASSY.
TRANSMISSION ASSY.
PAGE 70 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — TRANSMISSION ASSY.
TRANSMISSION ASSY.
NO
PART NO
0131A
0948
PART NAME
SCREW, SHS 1/4-20 X 1/4
WASHER, FLAT
HANDLE, THROTTLE HYD. SPEED CTRL.
NUT, NYLOC 1/4-20
KNOB, CONTROL
HANDLE, W/A TRANS. DISENGAGE
NUT, NYLOC 3/8-16
ROD END, 3/8-24 MALE LH
WASHER, FLAT 3/8 SAE
SCREW, HHC 3/8-16 X 3-1/4
QTY.
REMARKS
1
*
2
*
3
6
2
1
2
1
1
10
1
15168
10024
4403
15197
10133
15187
10136
1493
15193
5023B
15275
0205
0166A
25007
2063
4
*
5
*
6
*
7
*
8
9
10
10
1
*
*
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
TRANSMISSION DISENGAGE ASSY................. 1 ................ INCLUDES ITEMS W/
*
NUT, HEX FINISH 3/8-24
ROD, 14.0 LENGTH 3/8-24 RH/LH FEMALE
SCREW, HHC 3/8-16 X 1
1
1
4
4
2
1
1
1
2
1
3
1
1
1
1
1
2
2
1
1
1
3
2
1
1
1
1
1
1
1
1
1
1
1
WASHER, LOCK 3/8 MED
BOLT, SHOULDER 1/2 X 3/4 PLT
ROD END, 3/8-24 MALE RH
CHAIN, ROLLER #40, 51P
CONNECTOR LINK #40 CHAIN
GEAR, SPLINE 2.0 DIA X 2.5 L
SPROCKET 40 BS 36 X 3/4
KEY, SQUARE 3/16 X 1-1/4
SHAFT, TRANSMISSION 0.75 DIA X 15.8L
SCREW, HHC 3/8-16 X 1-1/4
SPRING, TRANS 1.22 X 3.00 80-100 LB/IN
SCREW, HHC 1/2-13 X4
15199
15391
15330
15145
0627
15329
1023
15196
8087
10176
2621
NUT, NYLOC 1/2-13
ZERK FITTING
1162A
15360
15327
15354
1493
CAP, ZERK FITTING
SPROCKET, 40BS10 X 17 MM X 1/8
MOUNT, TRANSMISSION W/A
TRANSMISSION, EATON MODEL 700-044
SCREW, HHC 3/8-16 X 3-1/4
KEY, WOODRUFF #3
1578
10018
15169
3455
SCREW, SHC 10-32 X 1
RETAINER, THROTTLE
CABLE CLAMP
15395
15146
10935
15454
1665
15788
1284
15452
15432
CONTROL, PUMP W/A
PULLEY OK 50 X 17 -3/16 KEY
PULLEY, IDLER - EFSON - SEE EXT DE
SPACER IDLER
SCREW, HHC 3/8-16 X 2
SPRING, 2.5L X 0.5D X 0.0DD DIA
SCREW, HHC 3/8-16 X 1-1/2
ARM, IDLER
BELT, 3L ACCU-LINK........................................ 1 .................. INSTRUCTION SHEET INCLUDED
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — ENGINE ASSY.
ENGINE ASSY.
PAGE 72 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2SP CONCRETE SAW — ENGINE ASSY.
ENGINE ASSY.
NO
1
PART NO
15511
15101
15243
15103
15535
15059
6059B
PART NAME
QTY.
REMARKS
ENGINE, 8.5HP KOHLER COMMAND
ENGINE, 9HP HONDA GX270K1QXC9
ENGINE, 20HP HONDA GX620TXF2
ENGINE, 13HP HONDA GX390K1QXC9
OIL DRAIN ASSY.
1
1
1
1
1
1
1
1
1
1
2
3
PULLEY, TL 3V 4.12” OD
KEY, 1/4”SQ. X 2”
4
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2S CONCRETE SAW — WIRING DIAGRAM (ENGINE/CONSOLE)
PAGE 74 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FS2/FS2S CONCRETE SAW — WIRING DIAGRAM (ENGINE/CONSOLE)
FS2/FS2S CONCRETE SAW — WIRING DIAGRAM ROCKER SWITCHES
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: February 22, 2006
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 30 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
The minimum charge for orders from Mul-
tiquipis$15.00net.Customerswillbeasked
for instructions regarding handling of orders
notmeetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
PAGE 76 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
6668
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE
800-478-1244 or 310-537-3700
FAX: 310- 537-4259
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
MAIN
800-421-1244 or 310-537-3700
FAX: 310-537-3927
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
WWW:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Milan Technology Switch MIL S500 User Manual
MTD Chipper 243 645C000 User Manual
Multiquip Cordless Saw PS706016 User Manual
Multi Tech Systems Network Card MT5634ZPX V92 ISA User Manual
Neuro Logic Systems Mouse 17 User Manual
Nortec Humidifier RESDELUX User Manual
Nortel Networks Telephone NN10300 009 User Manual
Olympus TV Receiver DS 660 User Manual
Optimus Cassette Player SCP 103 User Manual
Parkinson Cowan Cooktop U02059 User Manual