OPERATION AND PARTS MANUAL
SERIES
MODEL MVC98D2
ONE-WAY PLATE COMPACTOR
(YANMAR L48V6 DIESEL ENGINE)
Revision #1 (01/12/11)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
MQ MIKASA SERIES MVC98D2
PLATE COMPACTOR
YANMAR L48V6F3R4AAW4
ENGINE
Proposition 65 Warning .............................................. 2
Table Of Contents ...................................................... 4
Parts Ordering Procedures ........................................ 5
Safety Information................................................. 6-10
Dimensions .............................................................. 11
Specifications ........................................................... 12
General Information ................................................. 13
Plate Compactor Components................................. 14
Engine Components ................................................ 15
Setup ........................................................................ 16
Inspection............................................................ 17-18
Operation ............................................................ 19-20
Preparation For Long term Storage ........................ 20
Maintenance ....................................................... 21-23
Troubleshooting .................................................. 24-25
Explanation Of Code In Remarks Column ............... 26
Suggested Spare Parts ............................................ 27
Cylinder Block Assembly.................................... 40-41
Cylinder Head Assembly.................................... 42-43
Air Cleaner Assembly......................................... 44-45
Muffler Assembly ............................................... 46-47
Crankshaft and Camshaft Assembly ................. 48-49
Piston Assembly................................................. 50-51
Lub. Oil Pump and Governor Assembly ............. 52-53
Cooling and Starting Device Assembly.............. 54-55
Fuel Injection Pump Assembly........................... 56-57
Fuel Tank and Fuel Line Assembly .................... 58-59
Tools, Labels and Gasket Set Assembly............ 60-61
Terms and Conditions Of Sale — Parts .................. 62
NOTICE
Specification and part number are subject to
change without notice.
COMPONENT DRAWINGS
Decal Placement ................................................. 28-29
Body Assembly ................................................... 30-33
Vibration Assembly ............................................. 34-35
Water Tank Assembly .......................................... 36-37
Transport Wheel Assembly ................................. 38-39
PAGE 4 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only):
Order parts on-line using Multiquip’s SmartEquip website!
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
■ View Parts Diagrams
■ Order Parts
■ Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
Order via Phone:
1-800-427-1244
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
❒
❒
❒
❒
❒
Dealer Name and Address
✓ UPS/Fed Ex
✓ DHL
✓ Truck
■
■
Priority One
Ground
Shipping Address (if different than billing address)
Return Fax Number
■ Next Day
Second/Third Day
Applicable Model Number
■
Quantity, Part Number and Description of Each Part
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
Do not operate or service the equipment before reading
the entire manual. Safety precautions should be followed
at all times when operating this equipment.
Failure to read and understand the safety
messages and operating instructions could
result in injury to yourself and others.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
SAFETY MESSAGES
The four safety messages shown below will inform you
about potential hazards that could injure you or others.The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
DANGER,WARNING, CAUTION or NOTICE.
SAFETY SYMBOLS
DANGER
Indicates a hazardous situation which, if not avoided,
WILL result in DEATH or SERIOUS INJURY.
WARNING
Indicates a hazardous situation which, if not avoided,
COULD result in DEATH or SERIOUS INJURY.
CAUTION
Indicates a hazardous situation which, if not avoided,
COULD result in MINOR or MODERATE INJURY.
NOTICE
Addresses practices not related to personal injury.
PAGE 6 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
GENERAL SAFETY
CAUTION
NOTICE
„ This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
„ NEVER operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
„ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
„ Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
„ NEVER use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
„ NEVER operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
„ ALWAYS know the location of the nearest
fire extinguisher.
„ NEVER operate this equipment under the influence of
drugs or alcohol.
„ ALWAYS know the location of the nearest
first aid kit.
„ ALWAYS know the location of the nearest phone or keep
a phone on the job site. Also, know the phone numbers
of the nearest ambulance,doctor and fire department.
This information will be invaluable in the case of an
emergency.
„ ALWAYS check the equipment for loosened threads or
bolts before starting.
„ DO NOT use the equipment for any purpose other than
its intended purposes or applications.
„ ALWAYS clear the work area of any debris, tools, etc.
that would constitute a hazard while the equipment is
in operation.
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
COMPACTOR SAFETY
DANGER
WARNING
„ DO NOT place hands or fingers inside engine
compartment when engine is running.
„ NEVER operate the equipment in an explosive
atmosphere or near combustible materials.An
explosion or fire could result causing severe
bodily harm or even death.
„ NEVER operate the engine with heat shields or
guards removed.
„ Keep fingers, hands hair and clothing away
from all moving parts to prevent injury.
WARNING
„ NEVER disconnect any emergency or safety devices.
These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death.Disconnection of any of these
devices will void all warranties.
„ DO NOT remove the radiator cap while the
engine is hot. High pressure boiling water will gush out
of the radiator and severely scald any persons in the
general area of the compactor.
„ DO NOT remove the coolant drain plug
while the engine is hot. Hot coolant will
gush out of the coolant tank and severely
scald any persons in the general area of
the compactor.
CAUTION
„ NEVER lubricate components or attempt service on a
running machine.
NOTICE
„ DO NOT remove the engine oil drain plug while the
engine is hot. Hot oil will gush out of the oil tank and
severely scald any persons in the general area of the
compactor.
„ ALWAYS keep the machine in proper running condition.
„ Fix damage to machine and replace any broken parts
immediately.
CAUTION
„ ALWAYS store equipment properly when it is not being
used.Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel.
„ NEVER touch the hot exhaust manifold,
muffler or cylinder.Allow these parts to cool
before servicing equipment.
ENGINE SAFETY
DANGER
NOTICE
„ NEVER run engine without an air filter or with a dirty air
filter.Severe engine damage may occur.Service air filter
frequently to prevent engine malfunction.
„ The engine fuel exhaust gases contain poisonous carbon
monoxide. This gas is colorless and odorless, and can
cause death if inhaled.
„ NEVER tamper with the factory settings
of the engine or engine governor. Damage
to the engine or equipment can result
if operating in speed ranges above the
maximum allowable.
„ The engine of this equipment requires an adequate
free flow of cooling air. NEVER operate this equipment
in any enclosed or narrow
area where free flow of the
air is restricted. If the air
flow is restricted it will cause
injury to people and property
and serious damage to the
equipment or engine.
„ NEVER tip the engine to extreme angles during lifting as
it may cause oil to gravitate into the cylinder head, making
the engine start difficult.
PAGE 8 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
FUEL SAFETY
DANGER
BATTERY SAFETY (ELECTRIC START ONLY)
DANGER
„ DO NOT add fuel to equipment if it is placed inside truck
bed with plastic liner. Possibility exists of explosion or
fire due to static electricity.
„ DO NOT drop the battery.There is a possibility that the
battery will explode.
„ DO NOT expose the battery to open flames,
sparks, cigarettes, etc.The battery contains
combustible gases and liquids. If these
gases and liquids come into contact with a
flame or spark, an explosion could occur.
FUEL
WARNING
„ ALWAYS wear safety glasses when
handling the battery to avoid eye irritation.
The battery contains acids that can cause
injury to the eyes and skin.
FUEL
„ Use well-insulated gloves when picking up
the battery.
„ ALWAYS keep the battery charged. If the battery is not
charged, combustible gas will build up.
„ DO NOT start the engine near spilled fuel or combustible
fluids. Diesel fuel is extremely flammable and its vapors
can cause an explosion if ignited.
„ DO NOT charge battery if frozen. Battery can explode.
When frozen, warm the battery to at least 61°F (16°C).
„ ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
„ ALWAYS recharge the battery in a well-ventilated
environment to avoid the risk of a dangerous concentration
of combustible gases.
„ ALWAYS use extreme caution when working with
flammable liquids.
„ If the battery liquid (dilute sulfuric acid)
comes into contact with clothing or skin,
rinse skin or clothing immediately with
plenty of water.
„ DO NOT fill the fuel tank while the engine is running
or hot.
„ DO NOT overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or sparks from
the ignition system.
„ If the battery liquid (dilute sulfuric acid) comes into
contact with eyes, rinse eyes immediately with plenty
of water and contact the nearest doctor or hospital to
seek medical attention.
„ Store fuel in appropriate containers, in well-ventilated
areas and away from sparks and flames.
CAUTION
„ NEVER use fuel as a cleaning agent.
„ ALWAYS disconnect the NEGATIVE battery terminal
before performing service on the equipment.
„ DO NOT smoke around or near the
equipment. Fire or explosion could result
from fuel vapors or if fuel is spilled on a
hot engine.
„ ALWAYS keep battery cables in good working condition.
Repair or replace all worn cables.
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
TRANSPORTING SAFETY
CAUTION
„ NEVER allow any person or animal to stand underneath
the equipment while lifting.
NOTICE
„ Before lifting, make sure that the equipment parts (hook
and vibration insulator) are not damaged and screws are
not loose or missing.
„ Always make sure crane or lifitng device has been
properly secured to the lifting bail (hook) of the
equipment.
„ ALWAYS shutdown engine before transporting.
„ NEVER lift the equipment while the engine is running.
„ Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
„ Use adequate lifting cable (wire or rope) of sufficient
strength.
„ Use one point suspension hook and lift straight
upwards.
„ DO NOT lift machine to unnecessary heights.
„ ALWAYS tie down equipment during transport by
securing the equipment with rope.
ENVIRONMENTAL SAFETY
NOTICE
„ Dispose of hazardous waste properly.
Examples of potentially hazardous waste
are used motor oil, fuel and fuel filters.
„ DO NOT use food or plastic containers to dispose of
hazardous waste.
„ DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
PAGE 10 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
C
B
D
A
Figure 1. MVC98D2 Reversible Plate Compactor Dimensions
TABLE 1. DIMENSIONS
REFERENCE
LETTER
DIMENSIONS
IN. (MM)
A
B
C
D
19.75 in. (502 mm.)
26 in. (660 mm.)
40 in. (1,016 mm.)
22.75 in. (578 mm.)
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
TABLE 2. Specifications (Compactor)
Models
MVC-98D2
Centrifugal Force
Number of Vibrations
Traveling Speed
3,350 lbs. (1,520 kg)
6,000 vibrations/min
72 ft./min (22 meters/min)
19.6 x 22.0 in.
(498 x 559 mm)
Plate Size (LxW)
Operating Weight
218 lbs. (99 kg)
13.7 qt. (13.0 liters)
7092 sq. ft./hr.
Water Tank Capacity
Max. Area Of Compaction
Table 3. Specifications (Engine)
YANMAR
L48V6F3R4AAW4
Model
Air-cooled 4 stroke, Vertical
Single Cylinder, Diesel
Engine
Type
2.7 in. x 1.8 in.
(70 mm x 57 mm)
Bore X Stroke
Displacement
Max Output
219 cc (13.4 cu-in)
4.2 H.P./3600 R.P.M.
Engine
Approx. 0.63 U.S. gallons
(2.4 liters)
Fuel Tank Capacity
Fuel
Diesel Fuel
0.84 qts. (.80 liters)
Recoil Start
Lube Oil Capacity
Starting Method
13.1 x 15.1 x 16.5 in.
(332.5 x 384.5 x 417.8 mm
Dimension (L x W x H)
Dry Net Weight
58.4 lbs (26.5 Kg.)
PAGE 12 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL INFORMATION
Frequency/Speed
Plate Compactor
The compactor's vibrating plate maximum frequency is 6,000
vpm (vibrations per minute).The forward and reverse travel speed
of the compactor is approximately 72 ft./minute (22 meters/
minute).
The Mikasa MVC98D2 is a walk-behind plate compactor
designed for the compaction of sand, clay and asphalt.This plate
compactor is a powerful compacting tool capable of applying a
tremendous force in consecutive high frequency vibrations to a
soil surface. Its applications include soil compacting for road,
embankments and reservoirs as well as backfilling for gas
pipelines, water pipelines and cable installation work.
Water Sprinkler System
The water sprinkler system will provide about 20 minutes of
sprinkling with the water cock in the full open position and the
compactor operating at full speed. It is suggested to mix a small
amount of detergent or diesel fuel with water.This will allow the
water to the flow much easier.
Compactor Components
This plate compactor is comprised of an anti-vibration handle,
vibrating case (eccentric), water tank, guard hook, rubber shock
absorbers and a Yanmar diesel engine.
Controls
Vibratory Plates
Before starting the MVC98D2 Plate Compactor, identify and
understand the function of the controls and components as
indicated in Figure 2.
The vibratory plates of the MVC98D2 produce low amplitude
high frequency vibrations, designed to compact granular soils
and asphalt.
The resulting vibrations cause forward motion.The engine and
handle are vibration isolated from the vibrating plate.The heavier
the plate, the more compaction force it generates.
Power Transfer
The Mikasa MVC98D2 Plate Compactor is equipped with an air-
cooled, vertical single-cylinder, 4-stroke Yanmar L48V6 diesel
engine. A centrifugal clutch is attached to the output shaft of the
engine and will engage when the engine speed reaches
approximately 2,300 ~ 2,600 rpm’s.
Engine shaft speed is transfered via engine pulley and V-belt to
vibrator pulley. The vibrator pulley rotates an eccentric rotor shaft
that is contained within the vibrator case.
The generated vibration created from the eccentric rotor is
transmitted to the compacting plate. This vibration causes the
compactor to move in a forward direction.
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS
4
2
3
1
10
9
8
5
7
6
Figure 2. MVC98D2 Components
Figure 2 illustrates the location of the major components for the
MVC98D2 Plate Compactor.The function of each component is
described below:
5. Belt Cover – Remove this cover to gain acess to theV-belt.
NEVER run the compactor without theV-belt cover.If theV-
belt cover is not installed, the possibility exist that your hand
may get caught between theV-belt and clutch, thus causing
serious injury and bodily harm.
1.
Water Tank Cap – Remove this cap to add water to the
water tank.
6. Vibrating Plate – A flat, open plate made of durable cast
2.
Lifting Hook – When lifting of the compactor is required
either by forklift, crane etc., tie rope or chain around this
lifting point.
iron construction used in the compacting of soil.
7. Vibration Case – Encloses the eccentric, gears and
counter weights.
3.
Diesel Engine – This plate compactor uses a YANMAR
L48V6 engine. Refer to the YANMAR owners manual for
engine information and related topics.
8. WaterTube (Sprinkler) – Supplies water to the soil via a
splash plate.
4.
Handle Bar – When operating the compactor use this
handle bar to manuever the compactor.
9. Water Shut-Off Valve – Turn this valve downward to let
water flow from the water tank to the water tube.
10. Water Tank – Holds 13.7 quarts of water, removable no
tools required.
PAGE 14 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC ENGINE
9
3
4
1
2
10
5
11
7
6
8
Figure 3. Engine Controls and Components
7.
Oil Filler Cap / Dipstick – Remove this cap to add oil to the
engine crankcase. Read dipstick to determine if oil level is
low. DO NOT over fill.
The engine shown above is a YANMAR L48V6 engine (Figure 3).
The engine must be checked for proper lubrication and filled
with fuel prior to operation. Refer to the manufacturer’s engine
manual for instructions and details of operation and servicing.
Each component is described below:
NOTICE
Operating the engine without an air filter, with a damaged air
filter, or a filter in need of replacement will allow dirt to enter
the engine, causing rapid engine wear.
1.
Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
2.
Fuel Tank – Capacity is 2.5 quarts (2.4 liters) of diesel
8.
9.
Oil Drain Plug – Unscrew plug to drain oil from engine
crankcase.Dispose of oil in a safe manner.
fuel.
3.
Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
Decompression Lever– Press down before starting
engine.To prevent damage to engine, DO NOT use for any
other purpose.
4.
Muffler – Used to reduce noise and emissions.
5.
Recoil Starting Handle (pull rope) – Type of engine
starting method.
WARNING
Engine components can generate extreme
heat.To prevent burns, DO NOT touch these
areas while the engine is running or
immediatelyafteroperating. NEVER operate
the engine with the muffler removed.
WARNING
Add fuel to the tank only when the engine is
stopped and has cooled down. In the event
of a fuel spill, DO NOT attempt to start the
engine until the fuel residue has been
completely wiped up and the area
surrounding the engine is dry.
10. Fuel Cock– Controls the flow of diesel fuel to the carburetor.
Must be in the ON position when starting and running the
engine.
6.
Recoil Starter– Manual-starting method. Pull the starter
grip until resistance is felt, then pull briskly and smoothly.
11. Speed Control Lever– Regulates engine speed.
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
Compactor Instructions
Steering Handle Assembly
The purpose of this section is to assist the user in the setting
up of a NEW compactor. If your compactor is already
assembled (vibration handle), then this section can be
The steering handle is not attached to the compactor’s lower
base at the time of shipment.To attach the steeering handle
to the lower base assembly perform the following:
skipped
.
1. Remove the bolts and washers (handle mounting hard-
ware) from both sides of the plate compactor (Figure 4).
Before packaging and shipping this MQ MikasaWalk-Behind
Plate compactor was run and tested at the factory. If there
are problems, please let us know.
2. Position the anti-vibration handle over the compactor.
3. Align the holes at the bottom of the handle to the holes
on the compactor (lower base) where the bolts and wash-
ers where removed. Install and tighten the bolts and
washers.
NOTICE
The new plate compactor cannot be put into service until
the setup installation instructions are completed. These
setup instructions only need to be performed at the time
of unpacking a NEW compactor.
ANTI-VIBRATION
HANDLE
BASE PLATE
HANDLE MOUNTING
HARDWARE
Figure 4. Installing the Steering Handle
PAGE 16 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
CAUTION
CAUTION
NEVER operate the unit in a confined
area or enclosed area structure that does
not provide ample free flow of air.
4. If the oil level is low (Figure 6), fill to the edge of the oil filler
holewiththerecommendedoiltype(Table4).Maximum oil
capacity is 0.84 quarts (0.80 liters).
ALWAYS wear approved eye and hearing
protection before operating the unit.
Before Starting:
Figure 6. Engine Oil Dipstick (Oil Level)
Table 4. Oil Type
1.
Read safety instructions at the
beginning of manual.
2.
Remove dirt and dust, particularly
in the engine cooling air inlet,
carburetor and air cleaner.
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
3.
Check the air filter for dirt and dust.
If air filter is dirty, replace air filter
with a new one as required.
4.
5.
Check carburetor for external dirt and dust. Clean with dry
compressed air.
0°C or Lower
DANGER
Check fastening nuts and bolts for tightness.
EXPLOSIVE FUEL!
Explosive
Engine Oil Check:
Motor fuels are highly flammable and can
Fuel
1.
To check the engine oil level, place the compactor on secure
level ground with the engine stopped.
be dangerous if mishandled. DO NOT
smoke while refueling. DO NOT attempt to
refuel if the engine is hot or running.
2.
Remove the filler dipstick from the engine oil filler hole
(Figure 5) and wipe clean.
Fuel Check:
1. Remove the fuel cap located on top of fuel tank.
2. Visually inspect to see if the fuel level is low. If fuel is low,
replenish with clean diesel fuel.
3. Whenrefueling,besuretouseastrainerforfiltration.DONOT
top-off fuel.Wipe up any spilled fuel immediately!
Figure 5. Engine Oil Dipstick (Removal)
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
V-Belt Check
CAUTION
2. The V-belt tension is proper if theV-belt bends 10 to 15 mm
(Figure 9) when depressed with finger at midway between
the clutch and vibration pulley shafts.
NEVERattempttochecktheV-beltwiththeenginerunning.
Severeinjurycanoccurofyourhand(Figure7)getscaught
betweentheV-beltandtheclutch.Alwaysusesafetygloves.
CLUTCH
PULLEY
Figure 9.V-BeltTension
3. A looseV-belt will decrease the power transmission output,
causing reduced compaction and premature wear of the
belt.
VIBRATOR
PULLEY
4. If the V-belt becomes worn or loose, replace it. See
maintenance section.
Figure 7.V-Belt Hazard
1. To check the V-belt tension, remove the three bolts that
secure the belt cover to the frame as shown in Figure 8.
Vibrator Oil Check
1. Place the MVC98D2 plate compactor horizontally on a flat
surface.Makesurethecompactorislevelwhencheckingthe
oil in the vibrator assembly.
2. Check vibratoroillevelbyremoving theplug (vibrator oilgauge)
asshowninFigure10. Theoillevelshouldbeuptotheoilplug.
Thevibratorholds 140cc(approximately4oz.).IMPORTANT,
if oil is required, replace using only SAE10W-30 motor oil.
REMOVE
VIBRATOR
REMOVE
Mikasa
V-BELT
Figure 10.Vibrator Oil Plug
V-BELT COVER
Figure 8.V-Belt Cover Removal
PAGE 18 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
This section is intended to assist the operator with the initial
start-up of the compactor. It is extremely important that this
section be read carefully before attempting to use the compactor
in the field.
4. Grasp the starter grip (Figure 14) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
spondingtothecompressionpoint.Pullthestartergripbriskly
andsmoothlyforstarting.
Starting the Engine
1. Open the fuel cock (Figure 11).
Figure 14. Starter Grip
5. If the engine does not start, repeat steps 1 thru 4.
Figure 11. Fuel Cock
Operation
2.
Move the engine speed control lever (Figure 12) to the
IDLE position.
1. Once the engine has started, move the engine speed lever
quickly to the FAST (Figure 15) position.
2. With the engine speed control lever placed in the FAST
position,theenginespeedshouldbebetween2,300~2,600
RPM’s, thereforeengagingthecentrifugalclutch.
IDLE
ENGINE SPEED
CONTROL
LEVER
ENGINE SPEED
CONTROL
LEVER
FAST
Figure 12. Engine Speed Control Lever (Idle Position)
3. Push down the decompression lever (Figure 13) and re-
lease.
Figure 15. Speed Control Lever (Fast Position)
NOTICE
ALWAYS move the throttle lever quickly without
hesitation, because increasing the engine speed slowly
causes the clutch to slip.
Figure 13. Decompression Lever
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION/PREPARATION FOR LONG-TERM STORAGE
Normal Shut-Down Procedure:
CAUTION
1. Place the speed control lever in the IDLE position. Allow the
Make sure to follow all safety rules referenced in the safety
informationsectionofthismanualbeforeoperatingcompac-
tor. Keepworkareaclearofdebrisandotherobjectsthatcould
cause damage to the compactor or bodily injury.
engine to cool down for 2 to 3 minutes.
2. Next, place the speed control lever in the STOP position
(Figure 16) to stop the engine.
3. Close the fuel cock (Figure 11).
3. Firmlygaspthecompactor'shandlebar withbothhands,the
compactor will begin moving forward.
4. Slowlywalkbehindthecompactorandbeonthelookout for
anylargeobjectsorforeignmatterthatmightcausedamage
to the compactor or bodily injury.
5. Compactortravelingspeedmaydroponsoilswhichcontain
clay, however there may be cases where traveling speed
drops because the compaction plate does not leave the
ground surface easily due to the composition of the soil.To
rectify this problem do the following:
SPEED
STOP
CONTROL
LEVER
■
Check the bottom plate to see if clay or equivalent material
has been lodged in the plate mechanism. If so, wash with
water and remove.
Figure 16. Speed Control Lever (Stop Position)
Emergency Shutdown Procedure:
■
■
Remember the compactor does not work as efficiently on
clay or soils that have a high moisture content level.
1. Move the speed control lever quickly to the STOP position
If the soil has a high moisture level, dry soil to appropriate
moisture content level or carry out compaction twice.
(Figure 16).
2. Close the fuel cock.
NOTICE
Compactor Storage
Whenever the compactor's vibration becomes weak or lost
duringnormaloperation,regardlessofoperationhours,check
theV-beltandclutchimmediately.
For storage of the compactor for over 30 days, the following
is required:
■
■
Drain the fuel tank completely, or add STA-BIL to the fuel.
Run the engine until the fuel in the injection system is
completely consumed.
■
■
■
Completely drain the oil from the crankcase and refill with
fresh oil.
Pour 2 or 3 cc of SAE 30 oil into the cylinder and crank slowly
to distribute the oil.
Pull out the starter rope slowly and stop at the compression
point.
■
■
Clean all external parts of the compactor with a cloth.
Cover the compactor and store in a clean, dry place.
PAGE 20 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CAUTION
TABLE 6. MVC-98D2 ENGINE CHECK
Inspection and other services should always be carried out
on hard and level ground with the engine shutdown.
ITEM
HOURS OF OPERATION
Oil or Fuel Leak
Every 8 hours (every day)
Inspection and Maintenance ServiceTables.
Tightness of Fastening
Threads
Every 8 hours (every day)
To make sure your plate compactor is always in good working
condition before using, carry out the maintenance inspection in
accordance with Tables 5 through 7.
Every 8 hours (every day)
(Replenish to specified maximum
level)
Engine Oil Check and
Replenishment
TABLE 5. MVC-98D2 MACHINE
INSPECTION
After first 25 hours then every 50 to
100 hours
Engine Oil Replacement
Air Filter Cleaning
HOURS OF
Every 100 hours
ITEM
OPERATION
See separate engine manual for details on engine maintenance.
Loose or Missing
Screws
Every 8 hours (every
day)
Daily Service
Every 8 hours (every
day)
Damaged Parts
Check for leakage of fuel or oil.
V-Belt
Check/Replacement
Check for loose screws including tightness. See Table 7
below (tightening torque ), for retightening:
Every 200 hours
Clutch Check
Every 200 hours
Every 100 hours
TABLE 7.
Vibrator Oil Check
TIGHTENING TORQUE (in. kg/cm) Diameter
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm
Vibrator Oil
Replacement
Every 300 hours
Every 200 hours
4T
70
150
250
400
300
500
800
500
800
750
1,100 1,400
2,000
3,800
5,600
6-8T
11T
100
150
1,300 2,000 2,700
Clutch Check
1,200 2,000 2,900 4,200
300~ 650 ~
350 700
*
100
NOTICE
These inspection intervals are for operation under normal
conditions. Adjustyour inspection intervals based on the number
hours plate compactor is in use, and particular working
conditions. Fuel piping and connections should be replaced
every 2 years.
* (In case counter-part is of aluminum)
(Threads in use with this machine are all right handed)
Material and quality of material is marked on each bolt, and screw.
Remove soil and clean the bottom of compaction plate.
Check vibrating case for any oil leakage.
Check engine oil.
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Engine Oil Replacement
Checking and theV-Belt
1. Replace engine oil, first in 25 hours of operation and every
50 to 100 hours afterwards.
After 200 hours of operation, remove the belt cover to check theV-
belt tension (Figure 19).
2. Drain the engine oil when the oil is warm as shown in
1. Remove the belt cover.
Figure 17.
2. Tension is proper if the belt bends about 10 mm when
depressed strongly with finger between shafts. Loose or worn
V-belts reduces power transmission efficiency, causing weak
compaction and reduces the life of the belt itself.
Figure 17. Engine Oil (Draining)
3. Remove the oil drain bolt and sealing washer and allow the
oil to drain into a suitable container.
4. Replace engine oil in the oil tank with recommended type
oilaslistedinTable4.Engineoilcapacityis1.16quarts(1.1
liter). DO NOT overfill.
Figure 19. Checking V-beltTension
CAUTION
5. Install drain bolt with sealing washer and tighten securely.
NEVERattempttochecktheV-beltwith
the engine running. Severe injury can
occurifyourhandgetscaughtbetween
the V-belt and the clutch. Always use
safetygloves.
Air Filter Cleaning
1. Remove the air cleaner cover and foam filter element as
shown in Figure 18.
2. Tapthepaperfilterelement(Figure 18)severaltimesonahard
surfacetoremovedirt,orblowcompressedair[notexceeding
30psi(207kPa,2.1kgf/cm2)]throughthefilterelementfromthe
air cleaner case side.
Replacing theV-belt
CAUTION
1. Remove the V-belt cover (Figure 20).
NEVER brushoffdirt.Brushingwillforcedirtintothefibers
and cause poor performance in your air filter.Replace the
paper filter element if it is excessively dirty.
2. Using cutters, simply cut the worn or defective V-belt and
discard.
3. Place one end of the new V-belt onto the upper pulley (clutch
side).
3. Clean foam element in warm, soapy water or nonflammable
solvent. Rinse and dry thoroughly. Dip the element in clean
engineoilandcompletelysqueezeouttheexcessoilfromthe
element before installing.
4. Place a 19 mm offset wrench or the like onto the lower vibrator
pulley fastening bolt.
5. Place the other end of the V-belt onto lower vibrator pulley.
Rotate offset wrench clockwise so that theV-belt moves onto
the lower vibrator pulley.
Figure 18. Engine Air Filter
PAGE 22 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Checking and Replacing the Clutch
Checking the Clutch
1. With belt cover removed, visually check outer drum of the
clutch for seizure and "V" groove for wear or damage.
REMOVE
2. Clean the "V" groove as necessary.
VIBRATOR
3. Check the clutch lining and shoe for signs of wear. If the shoe
is worn, replace the clutch to prevent deficient power
transmission and slippage.
REMOVE
Replacing the Clutch
1. Place a 19 mm offset wrench or the like onto the lower vibrator
pulley fastening bolt.
2. While pulling back hard on theV-belt near the lower vibrating
pulley, rotate offset wrench clockwise so that theV-belt slips
off the lower vibrator pulley. SetV-belt aside.
Mikasa
V-BELT
3. Remove bolt at engine power output by giving a shock to an
engaged wrench (e.g. tapping with hammer) and rotate the
bolt counterclockwise.
V-BELT COVER
Figure 20. V-Belt Check
4. Remove clutch with a pulley extractor.
5. To install a new clutch, reverse steps 1-4.
Vibrating Case Oil Replacement (300 Hours)
CAUTION
Alwayscleantheareaaroundthevibratoroilplug(oillevel
check)holebeforeremovingplug.Thiswillpreventdirtand
debrisfromenteringthesystem.
1. Place the plate compactor horizontally on a flat surface.
2. Removeoildrainplug(Figure21)fromvibratoranddrainoil
fromthevibratingcase.
3. Using a funnel, fill vibrating case with SAE10W-30 motor
oil.The oil level should be up to the oil plug.The vibrator holds
140cc(approximately1pint).
4. Re-install oil drain plug into vibrator.
Figure 21. Oil Level Check Plug
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TABLE 8. ENGINE TROUBLESHOOTING
POSSIBLE PROBLEM
SYMPTOM
SOLUTION
Speed control lever is in "STOP" position?
No fuel reaching injection pump?
Defective fuel pump?
Set speed control lever to "START" position.
Add fuel. Check entire fuel system.
Replace fuel pump.
Fuel filter clogged?
Replace fuel filter and clean tank.
Replace or repair fuel line.
Faulty fuel supply line?
Engine will not start or start is
delayed, although engine can
be turned over.
Check piston, cylinder and valves. Adjust or
repair per engine repair manual.
Compression too low?
Repair or replace injector in accordance with
engine repair manual.
Fuel injector not working correctly?
Oil pressure too low?
Check engine oil pressure.
Comply with cold starting instructions and
proper oil viscosity.
Low starting temperature limit exceeded
Check whether clear (not turbid) fuel emerges
from the fuel line (detach from injection
pump). If the fuel is turbid or separated, warm
up the engine or drain the complete fuel
supply system. Refuel with winter grade diesel
fuel.
Fuel separates has inadequate resistance to
low temperatures?
At low temperatures engine will
not start.
Refill engine crankcase with correct type of oil
for winter environment.
Engine oil too thick?
Throttle lever in STOP position?
Fuel filter blocked?
Reposition throttle lever to RUN position.
Replace fuel filter.
Engine fires but stops soon as
starter is switched off.
Fuel supply blocked?
Fuel tank empty?
Check the entire fuel system.
Add fuel.
Engine stops by itself during
normal operation.
Fuel filter blocked?
Replace fuel filter.
Fuel tank empty?
Fill with No.2 diesel fuel.
Replace fuel filter.
Fuel filter clogged?
Low engine power, output and
speed.
Fuel tank venting is inadequate?
Ensure that tank is adequately vented.
See engine manual for corrective action.
Speed control lever does not remain in
selected position?
Engine oil level too full?
Air filter blocked?
Correct engine oil level?
Clean or replace air filter.
Adjust valves per engine specification.
See engine manual.
Low engine power output and
low speed, black exhaust
smoke.
Incorrect valve clearances?
Malfunction at injector?
PAGE 24 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TABLE 9. PLATE COMPACTOR TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
Engine speed too low?
SOLUTION
Set engine speed to correct RPM.
Check or replace clutch.
Clutch slips?
Travel speed too low, and vibration is
weak.
V-belt slips?
Adjust or replace V-belt.
Excessive oil in vibrator?
Drain excess oil and fill to proper level.
Check eccentric, gears and counter
weights.
Malfunction in vibrator housing?
V-belt slips?
Clutch slips?
Replace V-belt.
Check clutch springs and shoes.
Does not travel forward.
Check vibrator housing (eccentric,
gears and counterweights)
Vibrator locked?
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and
QTY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the“Remarks”
Column.
SAMPLE PARTS LIST
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
2%
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
WASHER, 3/8 IN....1 .....MQ-45T ONLY
2% 12347
3
4
12348
12349
HOSE ..................A/R ...MAKE LOCALLY
BEARING ..............1 .....S/N 2345B AND ABOVE
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
NO. Column
Indicated by:
Unique Symbols — All items with same unique
symbol
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
PART NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
“Not Sold Separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
PAGE 26 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SPARE PARTS
MQ MIKASA MVC98D2 PLATE COMPACTOR
W/YANMAR L48V6 DIESEL ENGINE
1 to 3 Units
Qty.
P/N
Description
3 ......... 070100382 ....... V-BELT A38 (BLUE)
2 ......... 956100050 ....... THROTTLE WIRE
3 ......... 11465012590 ... ELEMENT, A/C W/PRE-FILTER
1 ......... 11429955040 ... CAP, FUEL TANK
1 ......... 11429976630 ... ROPE, RECOIL STARTER
2 ......... 11429935110 ... LUB. OIL FILTER COMPLETE
2 ......... 11425055121 ... FILTER, FUEL STAINER
1 ......... 11429955100 ... FILTER, FUEL OIL
4 ......... 939010230 ....... SOCK ABSORBER
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS ASSY.
2
1
CAUTION
ATTENZIONE
ATENÇAÕ
PRECAUCION
* Read operator’s manual carefully before use.
* Libre le manual attentivement avant utillsation.
* Bitte lesen Sie vor inbetriebnahme der Maschine de
Bedienungsanleitung sogfältig durch.
* Prima dell’ uso leggere attentamente il manuale.
* Lee com atenÇão o manual de instruÇões antes de
usar.
* Leer detenidamente el mamual de instrucciones
antes de usar la maquina.
NPA-769
J
NPA-845
J
3
Serial No.
Model No.
CONTACT
MQ PARTS DEPT.
4
NPA-1066
5
8
6
V BELT RPF-3330
NPA-835
J
5
7
PAGE 28 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS ASSY.
NO.
1
2
PART NO.
920208450
920207690
PART NAME
DECAL, LIFTING POSITION
DECAL, CAUTION (MANUAL)
QTY.
1
1
REMARKS
NPA-845
NPA-769
3
4
5
6
7
8
PLATE, SERIAL NO ..................................... 1 ......... CONTACT MQ PARTS DEPT.
920210660
920201580
920101410
920105070
920208350
DECAL, DANGER-CAUTION
DECAL, MQ LOGO
1
2
1
1
1
NPA-106
NPA-158
NPA-141
NPA-507
NPA-835
DECAL, MIKASA LOGO (TRIANGLE)
DECAL, MIKASA LOGO (NAME)
DECAL, V BELT RPF3330
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
BODY ASSY.
PAGE 30 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
BODY ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
21
23
24
25
31
32
33
35
36
37
38
39
40
43
45
46
416115973
939010230
020310080
030210250
416115980
001221025
030210250
914410024
020310080
030210250
031110160
416456700
416456710
959404350
458337770
0320050150
416452760
458451380
001520825
070100382
416216390
001220825
030208200
031108160
952407100
416117760
001220825
030208200
031108160
001220820
416115930
416452730
404433430
416452360
952405600
001221253
030212300
416117520
001221025
030210250
416342980
001220820
030208200
VIBRATING PLATE
SHOCK ABSORBER 50D- 45H
NUT M10
WASHER, LOCK M10
BASE
1
4
4
4
1
4
4
1
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
5
5
1
1
2
2
2
2
2
2
1
4
4
1
4
4
BOLT 10 X 25 T
WASHER, LOCK M10
ENGINE ASSY. L48V6F3R4AAW4
NUT M10
WASHER, LOCK M10
WASHER, FLAT M10
ENGINE PLATE /FR (W BOLT)
ENGINE PLATE /RE (W BOLT)
EARTH WIRE
CLUTCH ASSY. A1- 124- 20
KEY
47
48
49
51
COLLAR 20- 25- 15.6
CLUTCH /WASHER
SOCKET HEAD BOLT 8 X 25 T
V- BELT A- 38 (BLUE)
BELT COVER (INSIDE)
BOLT 8 X 25 T
WASHER, LOCK M8
WASHER, FLAT M8
WASHER 9 X 25 6
BELT COVER
52
52-1
52-2
52-3
52-4
53
54
55
56
57
91
92
BOLT 8 X 25 T
WASHER, LOCK M8
WASHER, FLAT M8
BOLT 8 X 20 T
HANDLE
COLLAR 13- 20- 44
RUBBER 20 X 32 X 28.5
HANDLE STOPPER
WASHER 12.5 X 35 X 4.5
BOLT 12X65 T
WASHER, LOCK M12
GUARD HOOK
93
94
95
96
97
101
102
103
112
113
114
BOLT 10 X 25 T
WASHER, LOCK M10
MUFFLER GUARD
BOLT 8 X 20 T
WASHER, LOCK M8
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
BODY ASSY.
PAGE 32 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
BODY ASSY.
CONTINUED
NO.
A
PART NO.
PART NAME
QTY.
REMARKS
362910060
956100050
362341550
362910090
362455630
362455620
050100450
050200100
031110160
032110180
096206006
020410060
022131008
THROTTLE LEVER ASSY. ........................... 1 ......... INCLUDES ITEMS W/
*
151
152
THROTTLEWIRE 845- 1010
THROTTLE BODY
THROTTLE GEAR CP, W/BOLT
THROTTLE LEVER
SLIDER
O- RING G- 45
O- RING P- 10
WASHER, FLAT M10
CONICAL SPRING WASHER M10
SOCKET HEAD SCREW 6X6
NUT M10, H=6
CAP NUT M10
SOCKET HEAD SCREW 8X20
NUT M8, H=5
1
1
1
1
1
1
1
3
2
1
1
1
1
1
2
2
2
2
3
1
1
1
1
2
2
*
153
155
156
157
158
159
160
161
162
163
*
*
*
*
*
*
*
*
*
164* *096208020
165
166
167
168
020408050
001220620
030206150
031106100
*
BOLT 6X20 T
WASHER, LOCK M6
WASHER, FLAT M6
CAP NUT M6
CLAMP TC- 300
CLAMP CORD
NUT M6, SPECIAL- L10
NUT M6
ADJUSTING BOLT
NUT M6
168-1 022130605
169
170
171
172
173
174
175
511010040
954406820
959406800
020306050
10210067080
020306050
952401690
WASHER 7173
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATION ASSY.
PAGE 34 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATION ASSY.
NO.
PART NO.
416910030
416115991
953400170
953405260
001221640
939216499
031116260
416215530
040406211
416338900
416338910
416338920
060803060
050101000
001220825
030208200
416454430
951405240
952404250
001221025
030210250
PART NAME
QTY.
REMARKS
A
VIBRATOR ASSY. ......................................... 1 ......... INCLUDES ITEMS W/
*
61
VIBRATING CASE
PLUG 1/4” X 14 10L
PACKING 1/4 (CU)
BOLT 16 X 40 T
WASHER, LOCK M16
WASHER, FLAT M16
ECCENTRIC ROTATOR
BEARING 6211C4
CASE COVER (R)
CASE COVER (L)
BELT COVER GUARD
OIL SEAL TC- 35488
O- RING G-100
1
1
1
4
4
4
1
2
1
1
1
1
2
8
8
1
1
1
1
1
*
62
*
63
*
64
*
65
*
66
*
68
*
69
*
70
*
71
*
72
*
73
*
74
*
75
*
BOLT 8X25 T
76
*
WASHER, LOCK M8
PULLEY A1- 28- 81- 20
KEY 7X7X19 R
WASHER 11 X 40X 4
BOLT 10X25 T
78
79
*
*
80
*
81
*
82
WASHER, LOCK M10
*
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER TANK ASSY.
PAGE 36 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER TANK ASSY.
NO.
111
112
113
114
115
116
117
118
120
121
PART NO.
416910010
033910050
953406390
954403241
416338930
416338940
416452750
001740825
416452790
954300342
001241030
033910010
022910180
PART NAME
QTY.
REMARKS
WATER TANK ASSY. (ORANGE) ................. 1 ......... INCLUDES ITEMS W/
*
WASHER 14.5 X 30 X 1.6
PACKING 13 X 28 X 2
COCK PT1/4”, BH-1211 (AL)
SPRINKLING PIPE
PIPE HOLDER (L)
PIPE HOLDER (R)
FLANGE BOLT 8X25 (SUS)
PIPE HOLDER STAY
WATER TANK CAP (NBR)
BOLT 10X30 U
WASHER 10.5 X 21 X 2 (SUS)
NYLON NUT M10 (SUS)
1
1
1
1
1
2
1
1
1
2
1
*
122
123
124
*
*
*
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSPORT WHEEL ASSY.
PAGE 38 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSPORT WHEEL ASSY.
NO.
1
2
3
4
5
6
PART NO.
416116160
959404310
031120320
025203030
416454150
025403025
PART NAME
QTY.
REMARKS
WHEEL SHAFT
WHEEL 150X42
WASHER, FLAT M20
SPLIT COTTER PIN 3X30
ROLLER
1
2
2
2
2
3
SPRING PIN 3X25
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
CYLINDER BLOCK ASSY.
PAGE 40 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
CYLINDER BLOCK ASSY.
NO.
1
5
6
7
8
9
10
11
12
13
14
20
21
22
33
34
35
36
37
38
39
40
PART NO.
PART NAME
QTY.
REMARKS
11429501050
11439901700
26106100122
24162152112
26106080122
11429901200
11429901210
11429901220
11429901230
12495001250
11429501330
11429901380
11429901600
11429901800
11429901830
11425001841
22312040080
26226060182
26226060222
26366060002
11429901410
11428401452
11425002100
11425002200
11425002210
11429935150
26106060252
26106080352
11429901690
11429901760
11429901950
22190160002
11429902030
11425002113
11429902220
16021002220
23876010000
CYLINDER BLOCK ASSY.
STARTER COVER
BOLT M10X 12 PLATED
NEEDLE BEARING
BOLT M 8X 12 PLATED
CYLINDER HEAD BOLT A
CYLINDER HEAD BOLT B
CYLINDER HEAD NUT A
CYLINDER HEAD NUT B
WASHER
1
1
2
1
1
2
2
2
2
4
1
1
2
1
1
1
2
1
2
3
1
CYLINDER HEAD GASKET ASSY.
O- RING
PIN 8X12
SHIM SET
COVER, (FO PUMP)
GASKET
PIN 4X8 STRAIGHT
STUD M 6X 18 PLATED
STUD M 6X 22 PLATED
NUT M 6
CRANK CASE GASKET
CRANK CASE COVER .............................. 1 ................ INCLUDES ITEMS W/
MAIN BEARING US=STD.
BEARING US=0.25, MAIN
BEARING US=0.50, MAIN
L.O. INLET PIPE
BOLT M 6X 25 PLATED
BOLT M 8X 35 PLATED
PLUG M16
CAP, W/LUBE OIL GAUGE ....................... 1 ................ INCLUDES ITEMS W/
O- RING
SEAL WASHER 16S
RETAINER
BALL BEARING
OIL SEAL
*
45
45
1
1
1
1
14
1
*
45
48
49
50
53
54
2
#
56
57
58
59
60
61
62
#
1
2
1
1
1
1
1
OIL SEAL
PLUG PT 1/8, SCREW
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
CYLINDER HEAD ASSY.
PAGE 42 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
CYLINDER HEAD ASSY.
NO.
1
6
7
8
PART NO.
PART NAME
QTY.
REMARKS
11477111020
11477111100
11477111110
11429911120
1142511180
27310055001
22351040008
11477111250
11477111260
11477111650
11425011240
26856060002
11477111660
11425011240
26856060002
22242000120
11425011340
11926011370
11477111461
11429511470
11429911600
11429911901
26106060452
11471811910
26366060002
11477111310
11429511951
11425003591
11429903640
22312030160
26106060552
CYLINDER HEAD
SUCTION VALVE
EXHAUST VALVE
VALVE SPRING
SPRING RETAINER
COTTER
1
1
1
2
2
2
1
9
10
11
12
SPRING PIN 4X8
ARM SUPPORT CAM ................................. 1 .............. INCLUDES ITEMS W/
ROCKER ARM SUPPORT
INTAKE ARM ASSY. ................................... 1 .............. INCLUDES ITEMS W/
VALVE ADJUST. SCREW
LOCK NUT 6
EXHAUST ARM ASSY. ............................... 1 .............. INCLUDES ITEMS W/
VALVE ADJUST. SCREW
LOCK NUT 6
CIR CLIP 12
VALVE STEM SEAR
VALVE CAP
NOZZLE GASKET
NOZZLE SPACER
VALVE SPRING WASHER
NOZZLE RETAINER
BOLT M 6X45 PLATED
STUD BOLT M6X65
NUT M 6
*
%
13
14
*
1
*
16
17
18
20
21
22
23
24
25
26
27
28
29
30
31
32
33
35
38
39
55
%
%
1
1
$
*
$
1
1
2
2
2
1
1
2
1
2
2
2
1
$
*
BONNET GASKET
BONNET COMPLETE ................................. 1 .............. INCLUDES ITEMS W/
SHAFT ASSY. DECOMP.
SPRING, DECOMP.
PARALLEL PIN 3X16
BOLT M 6X 55 PLATED
#
#
#
#
1
1
1
3
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR CLEANER ASSY.
PAGE 44 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR CLEANER ASSY.
NO.
1
2
PART NO.
PART NAME
GASKET, AIR CLEANER
U- NUT
CLEANER, AIR ASSY. ................................ 1 .............. INCLUDES ITEMS W/
LABEL, AIR CLEANER
COVER COMPL.
CASE, AIR CLEANER
SEAL WASHER M8
ELEMENT W/ PRE- FILTER........................ 1 .............. INCLUDES ITEMS W/$
PRE- FILTER
WING NUT M8
INTAKE MANIFOLD
AIR INTAKE GASKET
BOLT M 6X 25 PLATED
STUD M 6X14 PLATED
STUD M 6X 55
QTY.
1
3
REMARKS
11429912210
11429912300
11428812511
11465007450
11428812520
11428812532
11425212560
11465012590
3
*
4
*
5
*
6
*
7
*
8
*
1
1
1
1
10 $ 11465012550
1
*
11
13
14
15
16
17
11425212550
11477112010
11477112200
26106060252
26226060142
26226060552
1
1
2
1
2
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
MUFFLER ASSY.
PAGE 46 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MUFFLER ASSY.
NO.
18
24
27
28
29
30
PART NO.
PART NAME
QTY.
REMARKS
11429913200
11428813500
26106060142
26216080182
26366080002
11429913800
MUFFLER GASKET
MUFFLER ASSY.
BOLT M6X14 PLATED
STUD M 8X 18 PLATED
NUT M 8
1
1
2
2
2
1
EXHAUST DEFLECTOR
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
CRANKSHAFT AND CAMSHAFT ASSY.
PAGE 48 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
CRANKSHAFT AND CAMSHAFT ASSY.
NO.
1
6
7
8
10
19
20
21
24
PART NO.
PART NAME
CAMSHAFT (D) ASSY.
TAPPET
TAPPET, F.O.
PUSH ROD
CRANKSHAFT ASSY.
NUT
FLYWHEEL WASHER
KEY 4X 12
FLYWHEEL ASSY. ...................................... 1 .............. INCLUDES ITEMS W/
QTY.
REMARKS
71429514580
11429914200
11477114260
11425014451
71477221701
11429921220
11429921550
22512040120
11429921590
11426221600
71477028531
24101062020
16031014550
22512050300
26106080202
1
2
1
2
1
1
1
1
*
27
61
RING GEAR
1
1
2
1
1
1
*
SHAFT ASSY. BEARING
BEARING 6202
WASHER
KEY 5X30
BOLT M8 X20 PLATED
66
67
68
69
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
PISTON ASSY.
PAGE 50 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PISTON ASSY.
NO.
28
28
PART NO.
PART NAME
QTY.
REMARKS
71429522720
71429522620
71429522580
71429522500
71429522540
71429522550
11429922300
22252000190
71429923700
11926523200
71477023600
71477023610
71477023620
11477023100
PISTON W/RINGS (D) STD. ........................ 1 .............. INCLUDES ITEMS W/
PISTON W/RING OS=0.25 .......................... 1 .............. INCLUDES ITEMS W/
PISTON W/RING OS=0.50 .......................... 1 .............. INCLUDES ITEMS W/
PISTON RING SET STD.
PISTON RING SET OS=0.25
PISTON RING SET OS=0.50
PISTON PIN
#
#
#
28
30
30
30
36
37
38
41
42
42
42
44
#
#
#
1
1
1
1
2
CIRCLIP 19
CONNECTING ROD ASSY.......................... 1 .............. INCLUDES ITEMS W/
ROD BOLT
CRANKPIN BEARING U.S=STD.
CRANKPIN BEARING U.S=0.25
CRANKPIN BEARING U.S=0.50
PISTON PIN BUSH
*
2
1
1
1
1
*
*
*
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
LUB. OIL PUMP AND GOVERNOR ASSY.
PAGE 52 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
LUB. OIL PUMP AND GOVERNOR ASSY.
NO.
1
7
PART NO.
PART NAME
QTY.
REMARKS
11425032010
11429932070
11429932570
22312030160
26106060122
11429935110
24341000224
26106060162
11429561190
22322030200
71477061100
11477061220
11477061520
11429961600
11477061610
11429961190
11425266051
18336060202
10522566990
26106060142
26106060202
11429966440
11429966440
26757060002
11477161810
11477161830
11429561940
11429966010
11429966200
11477166690
11481866600
13521061090
11477161890
LUB. OIL PUMP ASSY.
LUB. OIL PUMP COVER
O- RING COVER
1
1
1
1
3
9
10
11
12
PARALLEL PIN 3X16
BOLT M 6X 12 PLATED
LUB. OIL FILTER COMPLETE .................... 1 .............. INCLUDES ITEM W/
0- RING 1A S- 22.4
BOLT M 6X 16 PLATED
GOVERNOR LEVER ASSY.
TAPER PIN 3X20
#
14
15
16
22
23
25
29
30
31
32
40
42
43
44
45
46
47
48
49
50
51
52
53
54
55
57
58
#
1
1
1
1
GOVERNOR ASSY...................................... 1 .............. INCLUDES ITEM W/
*
GOVERNOR WEIGHT ASSY.
NEEDLE BEARING
OIL SEAL
THRUSTWASHER
GOVERNORWASHER
REGULATOR HANDLE
REGULATOR BRACKET
SCREW
BOLT M 6X 14 PLATED
BOLT M6X20 PLATED
RETURN SPRING
ADJUSTING BOLT
LOCK NUT M 6 PLATED
PLAIN WASHER 14
PLATE
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
*
NUT
REGULATOR SPRING
RETURN SPRING
NUT M14
FUEL LIMITER ASSY.
LEAD
PROTECTOR CMP ...................................... 1 .............. INCLUDES ITEMS W/+
60+
61+
62
11477161960
24311000180
22451060000
SPACER
O- RING 1A P-18.0
WIRE 0.6
1
1
1
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
COOLING AND STARTING DEVICE ASSY.
PAGE 54 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
COOLING AND STARTING DEVICE ASSY.
NO.
1
2
4
5
6
7
8
10
PART NO.
PART NAME
QTY.
REMARKS
11429945210
26106060122
11429545100
11429945300
11429945310
11429945330
11429945350
11429976250
11429976500
11429976520
11439976530
11439976540
11439975550
11439976560
11439976570
11439976580
11439976620
11429976630
11429976590
26106060082
26106060122
11429976600
11429976610
CYLINDER COVER
BOLT M 6X12 PLATED
COOLING FAN CASE
CUSHION RUBBER
FAN CASE COLLAR
FAN CASE SEAL
FAN CASE BOLT
1
1
1
4
4
1
4
RECOIL STARTER (D) ASSY. ..................... 1 .............. INCLUDES ITEMS W/
STARTER CASE
REEL
*
11
1
1
1
1
1
1
1
1
1
1
1
4
3
1
1
*
13
*
15
*
RATCHET
17
SPIRAL SPRING
RATCHET COVER
SPRING
RETURN SPRING
SCREW
STARTER KNOB
STARTER ROPE
STARTER PULLEY
BOLT M 6X 8 PLATED
BOLT M6X 12 PLATED
PLUNGER
*
19
*
20
*
21
*
22
*
23
*
24
*
25
26
27
29
30
PLUNGER HOLDER
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL INJECTION PUMP ASSY.
PAGE 56 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL INJECTION PUMP ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
71477551100
10554651020
11425051080
11425051160
11435051200
11425051300
10554651330
11425051340
12455051350
11425051600
11425051640
11425051650
22351020006
22351030008
71477553101
11477153001
11959353080
11425053120
11959353130
11477553140
11477553210
11477553100
INJECTION PUMP ASSY., F ...................... 1 .............. INCLUDES ITEMS W/
*
2
3
GASKET
PLATE
SPRING
1
1
1
1
1
1
1
2
1
1
1
2
1
*
*
4
5
*
FUEL INJECTION PUMP BODY
VALVE ASSY. DELIVERY
DELIVERY VALVE SPRING
F.I.P. DELIVERY HOLDER
DELIVERY GASKET
CONTROL LEVER ASSY.
SPRING SEAT ( A)
SPRING SEAT (B)
SPRING PIN 2X 6
SPRING PIN 3X 8
*
11
*
14
*
15
*
16
*
17
*
18
*
19
*
20
*
21
22
*
FUEL INJECTION VALVE ASSY. ................ 1 .............. INCLUDES ITEMS W/
#
23
24
25
26
27
28
29
#
FUEL INJECTION NOZZLE ASSY.
NOZZLE CASE NUT
NOZZLE SPRING
SPRING RETAINER
VALVE STOP SPACER
PIN
1
1
1
1
1
2
#
#
#
#
#
#
HOLDER ASSY. .......................................... 1 .............. INCLUDES ITEMS W/
%
32 #% 11477553330
PIN
SHIM PACK
FUEL INJECTION PIPE
1
1
1
33
#
11425053400
11477159803
44
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL TANK AND FUEL LINE ASSY.
PAGE 58 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL TANK AND FUEL LINE ASSY.
NO.
1
PART NO.
PART NAME
QTY.
REMARKS
71429955720
10530055080
23414080000
11429955100
11429955040
11429955201
11425055121
11425055130
11429955210
11429955230
11425055301
24341000150
11429955810
22117080000
26106080452
26368060002
26106060162
11477059030
11427059010
11426859061
12472259050
11425059060
FUEL TANK, BLACK..................................... 1 ............. INCLUDES ITEMS W/ #
3#
4#
5#
6#
7#
8
9%
10#
11
12
13+
14
15
16
17
18
19
DRAIN PLUG
1
1
1
1
4
ROUND GASKET 8
FILTER, FUEL OIL
FUEL TANK CAP ASSY.
FUEL TANK DAMPER
FILTER, FUEL STRAINER ........................... 1 ............. INCLUDES ITEM W/ %
GASKET
STAY
1
1
1
STAY (B)
COCK ........................................................... 1 ............. INCLUDES ITEM W/+
O- RING 1A S- 15.0
LIFTING BOLT
WASHER 8
BOLT M 8X 45 PLATED
NUT M6
BOLT M6X 16 PLATED
FUEL OIL PIPE ASSY. ................................ 1 ............. INCLUDES ITEMS W/
HOSE CLIP
FUEL OIL PIPE
CLAMP 9
1
1
1
1
2
2
*
20
2
1
2
1
*
21
*
22
23
FUEL RETURN PIPE
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS, LABELS AND GASKET SET ASSY.
PAGE 60 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS, LABELS AND GASKET SET ASSY.
NO.
3
4
5
6
7
10
PART NO.
PART NAME
QTY.
REMARKS
11429907100
11429907110
11421007120
11421007130
11429907160
11429992590
11429992600
11429992710
11429992720
11429992730
11429992740
71411092600
11429501330
11429901280
11429901410
11429901950
11425001841
22190160002
11425011340
11477111461
11477111310
11429912210
11477112200
11429913200
11429932570
24341000100
23414080000
24341000224
24341000150
AIR COOLED LABEL
YANMAR LABEL
CAUTION LABEL
HOW TO START -E LABEL
DIESEL LABEL
1
1
1
1
1
TOOL ASSY................................................. 1 .............. INCLUDES ITEMS W/
TOOL BAG
SPANA
SPANA
DRIVER
*
11
1
1
1
1
1
*
12
*
13
*
14
*
15
FUEL FITTING
*
16
GASKET SET ............................................. 1 .............. INCLUDES ITEMS W/
CYLINDER HEAD GASKET ASSY.
O- RING
CRANK CASE GASKET
O- RING
GASKET
WASHER SEAL 16S
VALVE STEM SEAL
NOZZLE GASKET
BONNET GASKET
AIR CLEANER GASKET
AIR INTAKE GASKET
MUFFLER GASKET
O- RING, COVER
O- RING 1A S-10.0
PACKING 8
#
17
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
1
1
1
2
1
2
2
1
1
1
1
1
1
1
1
1
1
O- RING 1A S- 22.4
O- RING 1A S- 15.0
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
5. Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
PAYMENT TERMS
Terms of payment for parts are net 30 days.
FREIGHT POLICY
6. The following items are not returnable:
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
LIMITATIONS OF SELLER’S LIABILITY
MINIMUM ORDER
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c. Any line item with an extended
dealer net price of less than
$5.00.
d. Special order items.
RETURNED GOODS POLICY
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
1. A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
7. The sender will be notified of any material
received that is not acceptable.
8. Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
2. To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
9. Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. The list must state the reason(s)
for the return.
Effective: February 22, 2006
d. The list must reference the sales
order(s) or invoice(s) under
which the items were originally
purchased.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
e. The list must include the name
and phone number of the person
requesting the RMA.
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
3. AcopyoftheReturnMaterialAuthorization
must accompany the return shipment.
4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
PAGE 62 — MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MVC98D2 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #1 (1/12/11) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
Warranty Department
800-421-1244
310-537-3700
Fax: 310-537-4259
Fax: 310-943-2238
800-421-1244
310-537-3700
Fax: 310-537-1173
Technical Assistance
800-478-1244
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223
Fax: (52) 222-285-0420 Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [email protected]
Fax: 0161 339 3226
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2011, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks
are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times.This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|