Simply Engineered Better
Technical Manual
Undercounter
Dishwasher
Model
401-HTM2 PLUS
401-HTNM2 PLUS
401-LTM2 PLUS
Machine Serial No.
September, 2003
2674 N. Service Road
Manual P/N 0510645
Jordan Station, Ontario, Canada L0R 1S0
905/562-4195
Fax: 905/562-4618
Moyer Diebel, Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
REVISIONS
Revision History
Revision
Date
Revised
Pages
Serial Number
Effectivity
Comments
7/16/03
All
Issue of manual and replacement parts lists.
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE
INTENTIONALLY
LEFT BLANK
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
CONTENTS
Page
INTRODUCTION....................................................................................................................................... 1
WARRANTY.............................................................................................................................................. 2
GENERAL .................................................................................................................................................. 3
INSTALLATION........................................................................................................................................ 5
Unpacking ............................................................................................................................................ 5
Electrical Connections.......................................................................................................................... 5
Plumbing Connections ......................................................................................................................... 6
Detergent .............................................................................................................................................. 6
Rinse-Aid ............................................................................................................................................. 6
Chemical Sanitizer ............................................................................................................................... 6
Completing Installation........................................................................................................................ 7
OPERATION .............................................................................................................................................. 8
Operation Summary ............................................................................................................................. 8
Operation Procedures ........................................................................................................................... 8
MAINTENANCE........................................................................................................................................ 10
Cleaning Schedule................................................................................................................................ 10
Deliming............................................................................................................................................... 11
Deliming Process.................................................................................................................................. 11
Maintenance Schedule.......................................................................................................................... 12
TROUBLESHOOTING .............................................................................................................................. 13
REPLACEMENT PARTS........................................................................................................................... 15
ELECTRICAL DIAGRAMS ...................................................................................................................... 39
TIMER CHARTS AND DIAGRAMS........................................................................................................ 44
LIST OF FIGURES
Figure 1—Track and Panel Assembly......................................................................................................... 16
Figure 2—Door and Switch Assembly........................................................................................................ 18
Figure 3—Tank/Drain Assembly ................................................................................................................ 20
Figure 4—Pump Assembly ......................................................................................................................... 22
Figure 5—Wash System Assembly............................................................................................................. 24
Figure 6—Booster Assembly and Water Inlet Piping (HT PLUS Only) .................................................... 26
Figure 7—Water Inlet Piping (HTN PLUS, LT PLUS Only)..................................................................... 28
Figure 8—Fill System ................................................................................................................................. 30
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Figure 9—Detergent Pump Assembly......................................................................................................... 32
Figure 10—Sanitizer/Rinse-Aid Pump Assembly....................................................................................... 34
Figure 11—Control Panel Assembly........................................................................................................... 36
Figure 12—Electrical Diagram, 401-HT PLUS.......................................................................................... 40
Figure 13—Electrical Diagram, 401-HTN PLUS....................................................................................... 41
Figure 14—Electrical Diagram, 401-LT PLUS .......................................................................................... 42
Figure 15—Timer Chart and Diagram, 401-HT PLUS............................................................................... 43
Figure 16—Timer Chart and Diagram, 401-LT PLUS ............................................................................... 44
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
INTRODUCTION
Welcome to Moyer Diebel.
Thank you for choosing Moyer Diebel and for allowing us to take care of your dishwashing
needs.
This manual covers several models. Model numbers are shown on the front cover.
Your machine has been completely assembled, inspected, and thoroughly tested at our factory to
eliminate problems at installation before it was shipped to your installation site. This manual
provides:
•
•
•
•
•
Warranty information
Installation and operation procedures
Maintenance instructions
Troubleshooting guide
Replacement parts lists.
Complete and return your warranty registration card as soon as possible.
Moyer Diebel constantly improves its products; therefore, specifications contained in this
manual may have changed.
For your protection, factory authorized parts should always be used.
Replacement parts may be ordered from your Moyer Diebel authorized parts distributor or
service agency. When ordering parts, supply the model number, serial number, voltage and phase
of your machine, the part number, part description, and quantity.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
LIMITED WARRANTY
Champion Industries/Moyer Diebel Limited, P.O. Box 4183, Winston-Salem, North Carolina 27115, and P. O. Box 301, 2674
North Service Road, Jordan Station, Ontario, Canada L0R 1S0 warrants machines, and parts, as set out below.
Warranty of Machines: Champion Industries/Moyer Diebel Limited warrants all new machines of its manufacture bearing
the name “Champion” or "Moyer Diebel" and installed within the United States and Canada to be free from defects in
material and workmanship for a period of one (1) year after the date of installation or fifteen (15) months after the date of
shipment by Champion/Moyer Diebel, whichever occurs first. [See below for special provisions relating to Model Series DF
and SW.] The warranty registration card must be returned to Champion/Moyer Diebel within ten (10) days after installation.
If warranty card is not returned to Champion/Moyer Diebel within such period, the warranty will expire after one year from
the date of shipment.
Champion/Moyer Diebel will not assume any responsibility for extra costs for installation in any area where there are
jurisdictional problems with local trades or unions.
If a defect in workmanship or material is found to exist within the warranty period, Champion/Moyer Diebel, at its election,
will either repair or replace the defective machine or accept return of the machine for full credit; provided, however, as to
Model Series DF and SW, Champion/Moyer Diebel's obligation with respect to labor associated with any repairs shall end
(a) 120 days after shipment, or (b) 90 days after installation, whichever occurs first. In the event that Champion/Moyer
Diebel elects to repair, the labor and work to be performed in connection with the warranty shall be done during regular
working hours by a Champion/Moyer Diebel authorized service technician. Defective parts become the property of
Champion/Moyer Diebel. Use of replacement parts not authorized by Champion/Moyer Diebel will relieve Champion/
Moyer Diebel of all further liability in connection with its warranty. In no event will Champion/Moyer Diebel's warranty
obligation exceed Champion/Moyer Diebel's charge for the machine. The following are not covered by Champion/Moyer
Diebel's warranty:
a. Lighting of gas pilots or burners.
b. Cleaning of gas lines.
c. Replacement of fuses or resetting of overload breakers.
d. Adjustment of thermostats.
e. Adjustment of clutches.
f. Opening or closing of utility supply valves or switching of electrical supply current.
g. Adjustments to chemical dispensing equipment.
h. Cleaning of valves, strainers, screens, nozzles, or spray pipes.
i. Performance of regular maintenance and cleaning as outlined in operator’s guide.
j. Damages resulting from water conditions, accidents, alterations, improper use, abuse,
tampering, improper installation, or failure to follow maintenance and operation procedures.
Examples of the defects not covered by warranty include, but are not limited to: (1) Damage to the exterior or interior finish
as a result of the above, (2) Use with utility service other than that designated on the rating plate, (3) Improper connection to
utility service, (4) Inadequate or excessive water pressure, (5) Corrosion from chemicals dispensed in excess of recom-
mended concentrations, (6) Failure of electrical components due to connection of chemical dispensing equipment installed
by others, (7) Leaks or damage resulting from such leaks caused by the installer, including those at machine table connec-
tions or by connection of chemical dispensing equipment installed by others, (8) Failure to comply with local building
codes, (9) Damage caused by labor dispute.
Warranty of Parts: Champion/Moyer Diebel warrants all new machine parts produced or authorized by Champion/Moyer
Diebel to be free from defects in material and workmanship for a period of 90 days from date of invoice. If any defect in
material and workmanship is found to exist within the warranty period Champion/Moyer Diebel will replace the defective
part without charge.
DISCLAIMER OF WARRANTIES AND LIMITATIONS OF LIABILITY. CHAMPION/MOYER DIEBEL'S
WARRANTY IS ONLY TO THE EXTENT REFLECTED ABOVE. CHAMPION/MOYER DIEBEL MAKES NO
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF
MERCHANTABILITY, OR FITNESS OF PURPOSE. CHAMPION/MOYER DIEBEL SHALL NOT BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THE REMEDIES SET OUT ABOVE ARE THE EXCLU-
SIVE REMEDIES FOR ANY DEFECTS FOUND TO EXIST IN CHAMPION/MOYER DIEBEL DISHWASHING
MACHINES AND CHAMPION/MOYER DIEBEL PARTS, AND ALL OTHER REMEDIES ARE EXCLUDED,
INCLUDING ANY LIABILITY FOR INCIDENTALS OR CONSEQUENTIAL DAMAGES.
Champion/Moyer Diebel does not authorize any other person, including persons who deal in Champion/Moyer Diebel
dishwashing machines, to change this warranty or create any other obligation in connection with Champion/Moyer Diebel
Dishwashing Machines.
rev. 8699
2
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL
GENERAL
This manual covers the Moyer Diebel 401PLUS undercounter dishwashing machine. This
machine is fully automatic and is equipped with a 1/2 H.P. pump motor. All models are available
for mounting directly to the floor or on optional stands (see accessories listed on page 4).
Standard equipment includes:
-Automatic tank fill
-Upper and lower spray arms
-Two dish racks (peg and flat)
-Exclusive vent design for
-Common utility connections
-120 Volt control circuit
-Convenient, easy to use controls
-Door latch activated start switch
-Pumped drain (to 3 ft/1m) (vertical)
venting of condensation
-Stainless steel heavy-gauge construction
-Detergent and rinse aid pumps
-Final rinse sentry feature (high temp
models only)
This series of dishwahers is available in he following models:
Model Numbers
401-HT PLUS, 401-HTN PLUS, 401-LTPLUS
•
•
•
The 401-HT PLUS model is a high temperature (82°C/180°F rinse) sanitizing model with
booster and the final rinse sentry feature.
The 401-HTN PLUS model is a high temperature (customer supplied 82°C/180°F rinse
water) sanitizing model without booster.
The 401-LT PLUS model is a low temperature (60°C/140°F rinse) sanitizing model.
Options
•
•
•
•
•
•
Kit 504 - Top and side panels (P/N 0708756)
Kit 505 - Top panel only (P/N 0708744)
Kit 506 - Left side panel only (P/N 0708745)
Kit 507 - Right side panel only (P/N 0708746)
Kit 510 - Extended reach pumped drain kit (P/N 0708766)
Kit 511 - 30°C/70°F temperature rise booster (P/N 0708753)
(for 49°C/110°F supply water).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL
Accessories
•
•
•
•
•
17RS - 17" rack stand (raises working height and adds rack storage)
17T - 17" cabinet (raises working height and adds storage)
CST - Combination sink/table (scraping and sorting station)
101285 - Dish Rack (Peg Rack)
101273 - Silverware Rack (Flat Bottom Rack)
Electrical Power Requirements
Booster
Rise
Machine
Power Requirement
Model
Voltage
Full Load Amp (125% Service Factor)
401-LT PLUS
401-HTN PLUS
401-HT PLUS
401-HT PLUS
401-HT PLUS
401-HT PLUS
115/60/1
115/60/1
208/60/1
240/60/1
208/60/1
240/60/1
N/A
N/A
40
9
15
15
42
47
57
64
9
33
37
45
51
40
70
70
NOTE:
208-230V/60Hz/1PH electrical supply service must be a 3-wire plus ground for connection
as shown.
00036
—3-Wire Plus Ground Diagram
115v
115v
208-230
L1
L2
N
G
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
INSTALLATION
Unpacking
WARNING:
!
Care should be taken when lifting the machine to prevent damage.
1. Immediately after unpacking your machine, inspect for any shipping damage. If damage is
found, save the packing material and contact the carrier immediately.
2. Remove the dishwasher from the skid. Adjust the feet if required, then move the machine to
its permanent location.
3. Level the machine (if required) by placing a level on the top of the machine and adjusting
the feet. Level the machine front-to-back and side-to-side.
CAUTION:
!
After locating your machine, the installation must meet local health codes. An example may
be to seal your machine to the floor using a good grade of silicone sealant.
Electrical Connections
WARNING:
!
Electrical and grounding connections must comply with the National Electrical Code
and/or Local Electrical Codes.
WARNING:
!
When working on the dishwasher, disconnect the electric service and tag it to indicate work
is being done on that circuit.
1. The electrician should compare the electrical specifications on the machine electrical rating
label (located on the lower left front panel) to the electrical power supply before connecting
the machine to the incoming service at a fused disconnect switch.
NOTE:
The 208-240V/60Hz/1PH electrical supply service for this machine must be a
3-wire plus ground service.
2. On the 208V-240V models, a terminal block is provided on the left front side of the
machine (located behind the front panel) for electrical service connections. A fused
disconnect switch or circuit breaker (supplied by user) is required to protect each power
supply circuit.
3. On 115V models, your machine is already equipped with a 4-foot power cord and plug
suitable for 115V-15A service.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Plumbing Connections
CAUTION:
!
Plumbing connections must comply with local sanitary and plumbing codes.
Water Connections
1. Connect the hot water supply (60°C/ 140°F Min) to the 1/2" I.D. fill hose provided. The fill
solenoid valve is equipped with a flow control that will accept water pressures from 172
kPa/25 psi to 665 kPa/95 psi.
2. Install a manual shut-off valve with 3/4" garden hose connection in the water supply line
close to the machine to accommodate installation and servicing the machine. The shut-off
valve should be the same size or larger than the supply line.
3. The fill solenoid valve is equipped with a built-in strainer to protect from particles in the
water supply.
Drain Connections
1. All Models are supplied with a flexible 5/8" I.D. drain hose, which must be connected to a
1-1/2" drain using a wye (Y) fitting close to the machine.
2. Drain connections height should be a maxium of 3 feet from the from the floor.
Detergent/Chemicals
Use a qualified detergent/chemical supplier for your detergent, rinse aid, and chemical
sanitizer needs.
1. Your machine has a liquid detergent dispensing pump. Insert the labeled detergent pickup
tube into the detergent container. The pickup tube has a strainer on the end to prevent
crystallized chemical from clogging the supply lines.
2. The cycle timer located in the main control cabinet is equipped with adjustable cams for the
chemical dispensing pump(s). The cams control the length of time that the pumps operate.
A qualified person may adjust the cam settings if necessary. Refer to the timer chart
diagram(s) at the end of the manual for timer cam locations. Factory time settings are only
approximate. Have your chemical supplier check the concentration and make the necessary
adjustments.
NOTE:
A nonchlorinated detergent is recommended for your dishwasher.
Rinse Aid
1. A rinse aid pump is included on all models. Insert the labeled Rinse Aid pickup tube into the
rinse aid container. Contact your chemical supplier for adjustment to ensure proper dosage.
Chemical Sanitizer
1. Model 401-LT PLUS is supplied with chemical sanitizer dispensing pump. Insert the
labeled Chemical Sanitizer pickup tube into the chemical sanitizer container. Have your
chemical supplier set chemical dosage according to local code.
2. Contact your chemical supplier for adjustment of the chemical sanitizer to ensure proper
dosage.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Completing Installation
1. Remove any foreign material from inside the machine.
2. Center the scrap screen over the sump opening.
3. Prime the booster using the following procedure (if applicable).
CAUTION:
!
To prime the booster, the folowing procedure must be followed AFTER the electrical
and plumbing connections have been made.
a. Remove the front panel.
b. Locate the Installation and Service toggle switch on the extreme left side of
of the control box.
c. Press the toggle switch to the Booster Fill position and hold it approximately
1 minute (or until water enters wash tank).
d. Release the toggle switch to stop the water flow.
e. You have complete the booster priming process.
NOTE:
Push the Installation and Service toggle switch to the ON position.
Electrical power is now supplied to the machine.
WARNING:
!
Failure to prime the booster may cause damage to the booster elements and other
electrical components and will void the warranty,
4. After plumbing and electrical connections are completed, check the machine for water leaks
by depressing the ON/FILL/OFF/DRAIN to the ON/FILL position, then close and latch
the door. This allows the tank to fill and complete the rinse cycle. Check for leaks.
4. Open the door and check the water level. The water level should be 1/2" over the scrap
screen.
5. Depress the ON/FILL/OFF/DRAIN switch to the OFF/DRAIN position, close and latch
the door to drain the machine. This allows the machine to complete the 105-second wash
and drain cycle. Check the drain plumbing for leaks or kinks in drain hose.
6. Replace the front panel. Installation is now complete.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
OPERATION
Operation Summary
The following is a summary of your Undercounter Dishwashing Machine operating cycle:
1. The cycle begins when you close and latch the door.
2. The green cycle lamp lights and the wash pump starts.
3. The pump runs during the wash cycle for approximately 80 seconds. The wash cycle
duration is extended if the booster is not up to temperature.
4. The wash pump stops, and the drain valve is opened.
5. After a 2-3 second pause, the pump drain cycle begins and continues for approximately 30
seconds. Just before this cycle ends the fill valve will come on for 2-3 seconds to flush the
wash tank of any remaining detergent.
6. After a 2-3 second pause, the fill valve opens, and the pump starts for the rinse cycle.
7. Within approximately 25 seconds, the rinse cycle is complete. The pump stops, the green
cycle lamp turns off, and the cycle is complete.
8. Open the door and remove the rack of clean ware.
Daily Operation Procedures
The operation of your dishwasher will be more efficient when these procedures are followed:
1. Check that the spray arm and scrap screen are in place.
2. Close and latch the door. Push the ON/FILL switch to the ON position. The tank will begin
filling with water. This procedure is followed only when the tank is empty.
3. When the tank is full, check the wash tank temperature gauge. Minimum wash temperatures
are:
• 401-HT PLUS, 401-HTN PLUS - 66°C/150°F.
• 401-LT PLUS - 60°C/140°F.
CAUTION:
!
If the wash water temperature falls below the minimums listed
above, you must run an empty cycle to refill with fresh hot water.
4. Scrap and preflush all items to be washed, and load the items into the rack. DO NOT
OVERLOAD the rack. Wash only one layer of silverware in a rack.
5. Open the door and insert the rack into the machine.
6. Close and latch the door. This will start the wash cycle. The green cycle lamp located on the
front control panel will light. This lamp will remain on until the entire wash and rinse
cycles are completed.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
NOTE:
The machine may be stopped at any time by opening the door. When restarted, the cycle
does not start over. It will continue from the point at which it was interrupted.
7. Check the rinse temperature during the final rinse (120 seconds into cycle). The rinse
temperature must be 82°C/180°F minimum for models 401-HT PLUS, 401-HTN PLUS
and 60°C/140°F for model 401-LT PLUS.
8. The pump will automatically stop and the green cycle light will turn off indicating the cycle
is completed.
9. Open the door and remove the rack.
10. Repeat steps 4-9 for additional cycles. Machine operation is automatic.
11. CLEAN the scrap screen after every meal period. During heavy usage, the scrap screen
should be cleaned more frequently.
CAUTION:
!
Poor machine performance and/or damage to the machine can occur if the scrap
screen becomes clogged with soil or waste particles.
12. To drain water out of the tank at the end of each day. Flip ON/FILL/OFF/DRAIN switch to
DRAIN position. Close and latch door. Machine will drain completely in approximately
105 seconds.
CAUTION:
!
DO NOT LEAVE WATER IN THE TANK OVERNIGHT. Water left in the tank
overnight will allow harmful chemicals to deteriorate the tank.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
MAINTENANCE
The efficiency and life of your machine is increased by regularly scheduled preventive
maintenance. A well maintained machine gives better results and service. An investment of a few
minutes of daily maintenance will be worthwhile.
The best maintenance you can provide is to keep your machine clean. Components that are not
regularly cleaned and flushed will clog and become inoperative.
Intervals shown in the following schedules represent an average length of time between necessary
maintenance. Maintenance intervals should be shortened whenever your machine is faced with
abnormal working conditions, hard water, or multiple shift operations.
Cleaning Schedule
•
Daily-Every 8 Hours
1. Depress the ON/FILL/OFF/DRAIN switch to OFF/DRAIN position and close and
latch the door to drain the tank.
2. Open the door and remove the upper and lower spray arms by unscrewing the knurled
fastener.
3. Remove the scrap screen carefully to keep soil or waste particles from falling into the
sump. Remove any material caught in pump intake.
4. Clean inside the tank with clean water. Backflush the scrap screen until it is clean. Do
not strike the screen against solid objects.
5. Clean the wash arms to remove any debris from spray openings. Do not strike the
spray arms against solid objects.
6. Reinstall the scrap screen and spray arms.
7. Leave the door open overnight to allow drying.
8. Report any unusual conditions to your supervisor.
Meal Periods
•
1. Clean the scrap screen after every meal period and more frequently during heavy
usage. Do not allow the scrap screen to become clogged with soil or waste particles.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Maintenance Schedule
•
As Required
1. Check the temperature gauge reading to make sure that it is accurate.
2. Check the chemical supplies and refill as necessary.
Weekly
•
1. Inspect all water lines for leaks and tighten them at joints if required.
2. Clean all detergent residue from the exterior of the machine.
3. Check the drain for leaks.
4. Remove and closely inspect the spray arms for blockage.
5. Check for damage to the scrap screen. Ineffective screening can cause wash system
failures, or poor washing results.
6. Clean the detergent, sanitizer, and rinse aid supply tubes. Complete the following
procedure:
a. Remove the detergent, sanitizer, and rinse aid pick-up tube(s) from the
container(s). Place the tube(s) into a container of hot water.
b. Ensure ON/FILL/OFF/DRAIN switch is in the ON position depress and hold
the DET prime switch (located on the front panel) until clear water enters the
tank through the fill air gap (located on the right side of the tank).
c. Your machine is equipped with a sanitizer and/or rinse aid pump, follow the
same procedure by pressing the SANITIZER and/or the RINSE AID prime
switch until clear water enters the tank through the fill air gap.
d. When completed, remove the pickup tubes from the hot water and reinsert them
into the correct chemical containers. Repeat the priming procedures to ensure
that chemicals have filled the tubes for the next operating period.
e. Run a complete cycle to flush chemicals from the tank.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Deliming
Your dishwasher should be delimed regularly. The frequency will depend on the mineral content
of your water.
Inspect your machine interior for lime deposits. If deliming is required, a deliming agent should
be used for best results.
DANGER:
!
Deliming solution or other acids must not come in contact with household bleach (sodium
hypochlorite) or any chemicals containing chlorine, iodine, bromine, or fluorine. Mixing
will cause hazardous gases to form. Skin contact with deliming solutions can cause severe
irritation and possible chemical burns. Consult your chemical supplier for specific safety
precautions.
If you have the chemical sanitizing model (401-LT PLUS), carefully follow the following
procedure before deliming:
1. Remove the sanitizer tube from the container. Place the tube into a container of hot water.
2. Depress and hold the SANITIZER prime switch (located on the front panel) until all
sanitizer has been purged from the hoses.
3. Close the door and depress the door latch. Complete two operating cycles to purge the
machine of all sanitizer.
Deliming Procedure
Complete the following procedure to delime your machine:
1. Add the delime chemical to wash the tank (per chemical supplier specifications).
2. Close and latch the door.
3. The dishwasher will complete a regular cycle.
4. Check the deliming results and repeat if necessary per the chemical supplier’s
specifications.
5. Operate the dishwasher for at least four complete cycles to purge the machine of any
deliming chemicals.
6. Drain the dishwasher. Deliming is complete.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TROUBLESHOOTING
Before determining any specific cause of a breakdown or abnormal operation of your dishwasher,
check that:
1. Power supply is turned on. All switches are ON.
2. Wash arms are clean.
3. Scrap screen is properly positioned and clean.
4. Thermostat is at the correct setting.
5. Sanitizer, detergent, and rinse additive dispensers are adequately filled.
6. All plumbing valves are open and drain hose is not kinked.
If a problem still exists, use the following table for troubleshooting.
CONDITION
Machine will not start
CAUSE
Door not closed and latched. . . . . . . .
Main switch off, or unit unplugged . .
SOLUTION
Make sure door is fully latched
Check disconnect or plug into outlet
Low or no water
Main water supply is turned off . . . .
Water level setting low. . . . . . . . . . . .
Turn on house water supply
Adjust water level
Chemical not feeding
No chemical in container . . . . . . . . . .
Feed tubes to/from chemical . . . . . . .
pump clogged
Replace or fill container
Clear obstruction and flush
with hot water
Screen on feed tube clogged. . . . . . . .
Tubing kinked or split . . . . . . . . . . . .
Clean and replace
Straighten or replace tubing
Water temperature
is low when in use
Incoming water temperature. . . . . . . .
at machine too low
Raise house supply temperature to
60°C/140°F for all machines
Insufficient pumped spray
pressure
Clogged spray arms . . . . . . . . . . . . . .
Scrap screen full. . . . . . . . . . . . . . . . .
Clean
Must be kept clean and in place
Low final rinse temperature
Low incoming water. . . . . . . . . . . . . .
temperature
Check the booster - be sure the
thermostat is set to maintain 66°C/180°F
temperature (401-L PLUS is 60°C/140°F)
(Check all valves to be
sure they are clean and operating)
Poor washing results
Detergent dispenser not . . . . . . . . . . .
operating properly
Contact service agent
Insufficient detergents . . . . . . . . . . . .
Check dosage
Check and fill
Contact detergent supplier
Contact detergent supplier
See above booster temperatures, run cycle
Clean wash arms
Check scraping procedures
Use proper racks - do not overload
racks
Detergent setting too low . . . . . . . . .
Wash water temperature too low . . . .
Wash arms clogged . . . . . . . . . . . . . .
Improperly scraped dishes . . . . . . . . .
Ware being improperly. . . . . . . . . . . .
placed in rack
Improperly cleaned . . . . . . . . . . . . . .
equipment
Unclog wash arms to maintain
proper pressure and flow conditions
No water in wash well
Opening door prior. . . . . . . . . . . . . . .
to cycle completion
Close and latch door. Wait for green light
to go out before opening door.
Water supply is turned off . . . . . . . . .
Turn on supply
No water in wash tank
after activating the
ON/FILL switch
Door not latched. . . . . . . . . . . . . . . . .
Latch door
Wait for wash tank to fill
Cycle time increases
with each cycle
Incoming water temperature. . . . . . . .
is too low
Raise temperature to 60°C/140°F for all
machines.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE
INTENTIONALLY
LEFT BLANK
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
REPLACEMENT
PARTS
15
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00050
12
11
10
12
7
6
4
9
5
3
12
2
8
1
Figure 1 — Track and Panel Assembly
16
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
TRACK AND PANEL ASSEMBLY
Description
Fig. 1
Item No. No.
Part
Qty
1
2
3
4
5
6
7
8
9
0508751
Screw, 10-32 x 1-1/2" Lg. Truss Head .......................................
Front Panel .................................................................................
Screw, 10-32 x 3/8" Lg. Round Head.........................................
Screw, 10-32 x 5/8" Lg. Round Head.........................................
Track, RH ...................................................................................
Track, LH ...................................................................................
Cover, Vent.................................................................................
Panel, LH Side ...........................................................................
Panel, Rear (HT PLUS) .............................................................
Panel, Rear (LT PLUS, HTN PLUS)..........................................
Panel, RH Side ..........................................................................
Panel, Top ..................................................................................
Screw, 10-32 x 3/8" Lg. Truss Head...........................................
2
1
2
4
1
1
2
1
1
1
1
1
10
0309572
0501413
0501415
0308632
0308631
0708647
0308736
0308734
0309573
0308737
0308735
0501412
9
10
11
12
17
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00020
11
1
5
4
8
7
6
10
9
12
3
1
14
13
2
1
15
18
16
17
15
Figure 2 — Door and Switch Assembly
18
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
DOOR AND SWITCH ASSEMBLY
Description
Fig. 2
Item No. No.
Part
Qty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
-
0501412
Screw, 10-32 x 3/8" Truss Head.................................................
Plate, Door Latch........................................................................
Handle, Door Latch....................................................................
Retaining Ring, Plunger.............................................................
Assembly, Door Catch (Includes items 4, 6)..............................
Plunger, Door Catch...................................................................
Gasket, Steam.............................................................................
Screw, Round Head (6-32 x 3/8") ..............................................
Plate, Door Switch......................................................................
Switch, Door Magnetic Reed .....................................................
Gasket, Upper Door....................................................................
Gasket, Side Door ......................................................................
Nut, Plain 1/4-20 ........................................................................
Spring, Door Hinge ....................................................................
Bolt, 1/4-20 x 1-1/4" Hex Head .................................................
Arm, Door Hinge........................................................................
Washer, Lock 1/4" Split .............................................................
Door............................................................................................
Wiring, Harness, Door Switch ...................................................
6
1
1
1
1
1
2
2
1
1
1
2
2
2
4
2
2
1
1
0308596
0308597
0508721
0709462
0509436
0508545
104883
0709431
111090
0508544
0508543
0501539
0503715
0501421
0708564
0501501
0708527
0508555
-
0708526
Door Assy. (includes items 1-6, 18)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00037A
1
9
TO RINSE
10
11
12
2
13
14
3
4
THERMOMETER
(CALLED OUT IN
CONTROL BOX)
TO PUMP
DRAIN
5
6
6
7
8
TO DRAIN
Figure 3 — Tank/Drain Assembly
20
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
TANK/DRAIN ASSEMBLY
Description
Fig. 3
Item No. No.
Part
Qty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
0508628
201029
Scrap Screen...............................................................................
Locknut, 1/2 NPT Nickel-Plated................................................
O-Ring, Thermometer................................................................
Adapter, Thermometer ...............................................................
Hose, 5/8" ID x 7/8" OD PVC Braided (3 ft.) ..............................
Clamp, hose................................................................................
Hose 5/8" ID x 1" OD Braided PVC..........................................
Valve, Drain................................................................................
Adapter, Pump Tube...................................................................
O-ring .........................................................................................
Nut, Jam 1"-8 .............................................................................
Tube, Pump Outlet .....................................................................
Thermostar, High Limit..............................................................
Nut, Grip 6-32 w/Nylon Insert...................................................
1
1
2
1
2
2
1
1
1
1
1
1
1
2
0501836
0508872
0507265
0510082
0509302
0306618
0508578
104414
0508579
0308655
110562
108954
21
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00005
1
3
2
4
5
6
7
8
9
10
13
14
11
12
TANK
BOTTOM
Figure 4 — Pump Assembly
22
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
PUMP ASSEMBLY
Description
Fig. 4
Item No. No.
Part
Qty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
*-
-
0508542
Spindle, Lower Wash Arm .........................................................
Screw, 8-32 x 1-1/8" Round Head..............................................
Screw, 8-32 x 5/8" Round Head.................................................
Housing, Top .............................................................................
Diffuser.......................................................................................
Impeller ......................................................................................
Adapter Plate, Suction................................................................
Plate, Drain lnlet.........................................................................
O-ring .........................................................................................
Propeller/Rotating Seal Assembly .............................................
Mounting Plate/Seal Assembly (Includes Item 10)....................
Gasket, Pump .............................................................................
Screw, 10-32 x 5/8" Hex Washer Head ......................................
Washer, Sealing Teflon...............................................................
Pump/Motor Assembly (60 Hz) (115V).....................................
Nut, Grip 10-32, SST (Not Shown) (For mounting Item 1).......
1
4
4
1
1
1
1
1
1
1
1
1
8
8
1
1
0501431
0501425
0508793
0502741
0502704
0502746
0502745
0502703
0502744
0502743
0501881
0508665
0508570
0710071
107966
* Motor not available as a separate repair part
23
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00038A
2
1
3
4
TOP OF
HOOD
5
6
7
8
9
10
10
11
12
13
PUMP
TANK BOTTOM
2
FROM
PUMP
Figure 5 — Wash System Assembly
24
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
WASH SYSTEM ASSEMBLY
Description
Fig. 5
Item No. No.
Part
Qty
1
2
3
4
5
6
7
8
9
10
11
12
13
0508549
Hose, Upper Wash......................................................................
Clamp, Hose 1" ..........................................................................
Spindle, Upper Wash Arm..........................................................
O-ring, 1-1/8" x 1-3/8"...............................................................
Screw 10-32 x 3/8 Truss Head ...................................................
Bushing, Upper Wash Arm ........................................................
Wash Arm, Upper.......................................................................
Pivot, Upper Wash Arm .............................................................
Retainer, Upper Pivot .................................................................
Screw, #8 x 3/8 Truss Head........................................................
Nut, Spray Arm Lock.................................................................
Wash Arm, Lower ......................................................................
Bushing, Lower Wash Arm........................................................
1
2
1
1
3
1
1
1
1
2
1
1
1
0502563
0708650
0503588
0501412
0508541
0710593
0505042
0308783
0501563
0501684
0705049
0508540
25
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
Figure 6 — Booster Assembly and Water Inlet Piping
(HT PLUS Only)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
BOOSTER ASSEMBLY AND WATER INLET PIPING
(HT PLUS ONLY)
Fig. 6
Part
Description
Qty.
Item No. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
---
---
---
0503679
Clamp, hose................................................................................
Hose, 1/2" I.D.............................................................................
Elbow, 3/8 MPT X1/2 Hose x 90°..............................................
Bushing, reducing 3/4 NPT x 3/8 NPT Brass ............................
Bolt., 1/4-20 x 1/2" Hex Head....................................................
Washer, Lock 1/4" Split..............................................................
Nut, Grip 6-32 w/Nylon Insert...................................................
Thermostat, high limit................................................................
Tank, booster (tank only)............................................................
Hose 1/2" I.D. (28") ...................................................................
Plug, pipe 1/8"............................................................................
O ring, gasket .............................................................................
Heater element, 6KW (40° rise) 208/230V 1PH........................
Heater element, 9KW (70° rise) 208/230V 1PH........................
Nut, plain 1/4-20 ........................................................................
Cover, heater element.................................................................
Wire, Jumper Heater Element (Not Shown)...............................
Insulation, Heater Terminal (Not Shown) ..................................
Label, Cover Warning (Not Shown)...........................................
2
3 ft.
1
2
2
5
2
1
1
A/R
1
1
1
1
1
1
1
1
0509214
0502653
0508840
0501419
0501501
108954
110562
0509042
107417
0508817
109985
111235
111233
0501539
107908
110997
0307356
0508937
1
27
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
Figure 7 — Water Inlet Piping
(HTN PLUS, LT PLUS Only)
28
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
WATER INLET PIPING
(HTN PLUS, LT PLUS ONLY)
Description
Fig. 7
Item No. No.
Part
Qty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
0503718
0503679
107417
Foot, adjustable ..........................................................................
Clamp, hose................................................................................
Hose, 1/2" ID (LT PLUS Only).................................................
Hose, 1/2" I.D (HTN PLUS Only).............................................
Elbow, 3/8 MPT x 1/2" Hose x 90° Brass..................................
Valve, solenoid (3/8NPT)...........................................................
Repair kit, 3/8" valve..................................................................
Coil, 115V 3/8" valve.................................................................
Flow washer, 3/8" valve .............................................................
Washer, lock 1/4" split................................................................
Bolt, 1/4-20 x1/2" Hex Hd .........................................................
Clamp, valve support..................................................................
Coupling, 3/8 MPT x 3/4" hose barb .........................................
Washer, hose...............................................................................
4
3
3 ft.
3 ft.
1
1
1
1
1
2
2
1
1
107417
0502653
0504952
0502811
0505235
0504958
0501501
0501419
0300203
0502618
0505320
1
29
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00039
Figure 8 — Fill System
30
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
FILL SYSTEM
Description
Fig. 8
Item No. No.
Part
Qty
1
2
3
4
5
6
7
8
107417
Hose, 1/2" I.D. (HTN PLUS, LT PLUS)....................................
Tie Wrap, Hose...........................................................................
Bracket, Tie Wrap ......................................................................
Nut, Grip, 10-32 w/Nylon Insert................................................
Gasket, Inlet Chute.....................................................................
Inlet Chute..................................................................................
Tie, Nylon 4"..............................................................................
Hose, Fill 1/2" I.D. ....................................................................
A/R
2
3
8
1
1
3
3 ft.
0501518
106090
107966
0509048
0508867
0501519
107417
31
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
1
00022
Rinse Aid
2
6
7
22
4
Detergent
1
23
2
3
21
5
24
25
6
TO FILL
SYSTEM
7
25
4
11
26
12
8
13
14
9
19
20
10
TO FILL
ASSY
15
16
15
16
15
TO CHEMICAL SUPPLY
17
15
18
19
20
TO DETERGENT
SUPPLY
Figure 9 — Detergent/Rinse Aid Pump Assemblies
(HT PLUS, HTN PLUS)
32
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
DETERGENT/RINSE AID PUMP ASSEMBIES
(HT PLUS, HTN PLUS)
Fig. 9
Part
Description
Qty
Item No. No.
1
1
2
3
4
5
6
7
8
0503757
Motor, Pump (Detergent) ...........................................................
Motor, Pump Injector (Rinse Aid) .............................................
Bracket, Detergent/Sanitizer Pumps (Rinse Aid).......................
Screw, M4 x 35mm Hex Head ...................................................
Screw, 10-32 x 3/8" Lg. Truss Head...........................................
Housing, Pump...........................................................................
Washer, Lock #8 Split ................................................................
Screw,8-32 x 1/2" Lg. Pan Head ................................................
Screw, 8-32 x 5/8" Round Head.................................................
Screw, Set M6 x 8mm ................................................................
Rotor Assembly..........................................................................
Hose, Pump ................................................................................
Cover, Pump Housing ................................................................
Washer, Flat M4 .........................................................................
Nut, Wing M4.............................................................................
Tie Wrap, Hose...........................................................................
Hose, Detergent, 1/4" I.D. PVC (Clear).....................................
Elbow, 1/4" O.D. x 90° Barbed ..................................................
Label, Detergent.........................................................................
Tube, Pick-Up ............................................................................
Strainer, Pick-Up Tube...............................................................
Tie Wrap, Hose...........................................................................
Rotor Assembly..........................................................................
Element Tube Assy (45CC/Min)................................................
Screw, 6-32 x 7/8 Pan Head .......................................................
Hose, 1/8" ID PVC (Clear).........................................................
Label, Rinse Aid.........................................................................
1
1
1
4
2
1
2
2
2
1
1
1
1
4
4
2
A/R
2
1
1
1
2
1
1
2
A/R
1
0503756
0308610
N/A
0501412
N/A
0501497
0504822
0501425
N/A
N/A
108194
N/A
N/A
N/A
0501519
0502667
0502644
0503695
0306363
0501869
0501519
0707142
0706634
0506589
0502666
0505483
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
-
-
-
109829
0709624
0708754
Detergent Pump Head Assy. (includes items 4, 6, 10-15)
Detergent Pump/Motor Assy. (includes items 1, 4, 6-20)
Rinse Aid Pump Assy (includes items 1, 6, 7, 19-26)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00002
1
3
2
5
6
7
8
4
15
9
10
TO FILL
SYSTEM
DETERGENT
PUMP (SEE FIG. 9)
10
11
12
13
14
TO CHEMICAL SUPPLY
Figure 10 — Detergent/Sanitizer/Rinse-Aid Pump Assembly
(LT PLUS Only)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
DETERGENT/SANITIZER/RINSE-AID PUMP ASSEMBLIES
LT PLUS ONLY
Fig. 10
Part
Description
Qty
Item No. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0503756
Motor, Pump...............................................................................
Bracket, Detergent/Rinse Pump ................................................
Bracket, Sanitizer Pump.............................................................
Screw, 10-32 x 3/8" Lg. Truss Head...........................................
Washer, Lock #8 Split ................................................................
Screw, 8-32 x 1/2" Lg. Pan Head ...............................................
Rotor Assy..................................................................................
Element Tube Assy (45cc/min)..................................................
Screw, 6-32 x 7/8" Lg. Pan Head ...............................................
Hose, 1/8" I.D. PVC (Clear).......................................................
Label, Sanitizer...........................................................................
Label, Rinse-Aid ........................................................................
Tube, Pick-Up ............................................................................
Strainer, Pick-up Tube................................................................
Tie Wrap, Hose...........................................................................
1
1
1
2
4
4
1
1
2
A/R
1
1
1
1
0308610
0308697
0501412
0501497
0504822
0707142
0706635
0506589
0502666
0503694
0505483
0306363
0501869
0501519
2
-
-
0709624
0708754
Detergent Pump Assy. ...............................................................
(lncludes Detergent Pump and Items 2, 5-9)
1
Rinse-Aid Pump Assy (Includes Items 1,3, 5-10, 12-15)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
S
L
U P
Figure 11 — Control Panel Assembly
36
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
CONTROL PANEL ASSEMBLY
Description
Fig. 11
Item No. No.
Part
Qty.
*1
*1
*1
2
3
4
4
5
6
7
0710583
Timer assy (HT PLUS Only) (Includes items 2-5) ....................
Timer assy (HTN PLUS Only) (Includes items 2-5) .................
Timer assy (LT PLUS Only) (Includes Items 2-5).....................
Motor, timer................................................................................
Switch, timer ..............................................................................
Bracket, timer support (HTN PLUS) .........................................
Bracket, timer support (HT PLUS, LT PLUS)...........................
Bearing, timer.............................................................................
Contactor, 2 pole 50A, 240V (401 HT PLUS only) (Booster)...
Relay, motor start (115V, 50Hz).................................................
Relay, door safety switch (15A, 120VAC coil) ..........................
Screw (10-32 x 3/4 Rd Hd) ........................................................
Washer, lock (#10 ext. tooth)......................................................
Washer, flat (#10 ss)...................................................................
Nut, plain (10-32 Brass).............................................................
Board, terminal...........................................................................
Bracket, thermostat (401 HT PLUS only)..................................
Thermostat, booster (401 HT PLUS only).................................
Thermometer, 4 ft. Gas Filled ...................................................
Lamp, green................................................................................
Switch, rocker (DPDT) ..............................................................
Switch, rocker (Spring return)....................................................
Label, switch, overlay ................................................................
French label, switch overlay.......................................................
Screw (10-32 x 3/8" Truss Hd)...................................................
Panel (sheet metal only) ............................................................
Block, terminal (HT PLUS) .......................................................
Switch, 3 position toggle ...........................................................
Relay 2PDT 10A 240V .............................................................
Harness, Control Box (HT PLUS) (Not Shown)........................
Harness, Conrtol Box (HTN PLUS) (Not Shown).....................
Harness, Control Box (LT PLUS) (Not Shown) ........................
1
1
1
1
A/R
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
0708538
0708590
0504956
0501379
0308644
0308645
0503701
111703
0501358
0509428
0501403
0501493
0507709
0501533
0503749
0310330
109069
8
9
10
11
12
13
14
15
16
17
18
19
20
20
21
22
23
24
25
—
—
—
113622
0508551
0501361
0501369
0509568
0509626
0501412
0309579
0504951
0501373
111069
0510582
0509608
0509611
37
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE
INTENTIONALLY
LEFT BLANK
38
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SCHEMATICS
ELECTRICAL
SCHEMATICS
39
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SCHEMATICS
TO CUSTOMER DISCONNECT SWITCH
CUSTOMER TO SUPPLY RATED
115V
NEUTRAL
VOLTAGE/PHASE/Hz, AS SPECIFIED
PER ORDER, TO DISCONNECT SWITCH.
ALL POWER SUPPLIED TO EACH CONNECTION
POINT MUST COMPLY WITH ALL LOCAL
ELECTRICAL CODES.
230V
SERVICE
SWITCH
GND
25
5
FILL
2
2
3
1
3
2
OFF
33
CT
CTC
1
1
NO
NC NC
NO
ON
32
31
28
29
MSW
ON
4
BOOSTER TANK
33
31
BHTR
5
5
35
NO
NC
4
30
31
WTS
HLTS
8
32
33
33
2CR
OFF
NO
NC
3
3
CAM 9
TM
4
6
10
11
WHTR
WTS
HLTS
35
NO
NC
1CR
NO
NC
8
4
8
CAM 1
NO
CAM 8
NC
8
7
CLT
16
17
PSDR
WASH/
4
START CW
START CCW
MAIN
BLU
RED
BLK
13 /RINSE
1
2
NO
CAM 3
NC
SRC
12
15
9
NO
CAM 2
NC
8
14
DRAIN
15
3
25
25
NO
NC
19
3
WHT
GRN
TP
F V
4
5
CAM 5
(IF USED)
DP
20
3
GND
GND
NO
NC
3
3
3
20
D V
CAM 4
CAM 7
8
16
8
16
NO
NC
21
DM
17
17
8
(IF USED)
22
NO
NC
3
RM
CAM 6
DSS
5
5
50
ICR
WTS
WATER THERMOSTAT
BHTR
BOOSTER HEATER
BLACK
MSW
MAIN SWITCH ON/FILL OFF/DRAIN
PRIME SWITCH DETERGENT, RINSE
RELAY
CLT
CT
CYCLE ON LIGHT
CONTACTOR
BLK
BLU
PSDR
1CR
BLUE
CTC
DM
DP
CONTACTOR COIL
2CR
RINSE SENTINEL RELAY
CAM 1
CAM 2
HOMING
DETERGENT MOTOR
PUMP MOTOR
DSS
RM
DOOR SAFETY SWITCH
DRAIN PUMP (IF USED)
DOOR SWITCH
RINSE MOTOR (IF USED)
CAM 3
PUMP MOTOR REVERSING
DS
SRC
CURRENT OPERATED START RELAY COIL
CAM 4
CAM 5
DRAIN
FILL
DV
DRAIN VALVE
SKH
SS
TM
SERVICE SWITCH
TIMER MOTOR
RELEASED TO
PRODUCTION
EC/D
EXTENDED CYCLE/DELIME
JUL
28-03
A
CAM 6
RINSE
FV
FILL VALVE
GROUND
GREEN
CAM 7
CAM 8
CAM 9
DETERGENT
CYCLE
TP
THERMAL PROTECTOR
WHITE
GND
GRN
BY
CH
WHT
WHTR
ECN
DESCRIPTION
REV
DATE
WATER HEATER
RINSE SENTINEL
HTLS
HIGH LIMIT THERMOSTAT
TOLERANCE
DECIMAL
ANGLE
ISSUED
HOLE DIMENSIONS
SCHEMATIC 401+ SERIES HIGH TEMP
A
B
C
F
DR.
G
DRAWING NO.
SCALE
1:1
CH.
FORMING:DIMENSIONS ARE FROM
BRAKELINE TO BRAKELINE
UNLESS OTHERWISE NOTED
H
J
D
E
RTG.
0510652
Figure 12 — Electrical Diagram, 401-HT PLUS
40
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SCHEMATICS
CUSTOMER TO SUPPLY RATED
VOLTAGE/PHASE/Hz, AS SPECIFIED
PER ORDER, TO DISCONNECT SWITCH.
ALL POWER SUPPLIED TO EACH CONNECTION
POINT MUST COMPLY WITH ALL LOCAL
ELECTRICAL CODES.
TO CUSTOMER RECEPTACLE
115V 60Hz
BLK
WHT
GND
2
1
1
8
2
2
MSW
ON
CLT
34
1
6
7
NO
NC
NO
NC
4
8
8
8
8
CAM 1
TM
NO
CAM 8
NC
WASH/
13
5
START CW
START CCW
MAIN
BLU
RED
BLK
OFF
1CR
/RINSE
1
2
NO
CAM 3
NC
SRC
L
S
9
9
12
NO
CAM 2
NC
14
DRAIN
15
M
15
3
4
5
NO
WHT
GRN
19
2
2
TP
CAM 5
F V
NC
8
(IF USED)
DP
20
NO
NC
2
2
20
D V
CAM 4
CAM 7
CAM 6
GND
GND
8
8
8
16
NO
NC
21
22
2
2
DM
16
17
PSDR
34
17
(IF USED)
RM
NO
NC
DSS
1
1
50
2
1CR
BLK
BLACK
BLUE
PSS
ICR
DSS
RM
PRIME SWITCH SANITIZER
RELAY
CLT
CYCLE ON LIGHT
BLU
DM
DP
RL
DV
DETERGENT MOTOR
DRAIN PUMP
RELAY
(IF USED)
REED SWITCH
CAM 1
CAM 2
HOMING
PUMP MOTOR
RINSE MOTOR
(IF USED)
DRAIN VALVE
SRC
CURRENT OPERATED START RELAY COIL
CAM 3
CAM 4
CAM 5
CAM 6
CAM 7
PUMP MOTOR REVERSING
DRAIN
FV
FILL VALVE
GROUND
GREEN
SM
TM
SANITIZER MOTOR
TIMER MOTOR
FILL
GND
GRN
HTLS
RINSE
TP
THERMAL PROTECTOR
WHITE
SKH
AUG
01/03
RELEASED TO
PRODUCTION
DETERGENT
HIGH LIMIT THERMOSTAT
WHT
A
WHTR
WTS
WATER HEATER
WATER THERMOSTAT
MSW
MAIN SWITCH ON/FILL OFF/DRAIN
PRIME SWITCH DETERGENT, RINSE
CAM 8
CYCLE
BY
CH
REV ECN
DESCRIPTION
DATE
PSDR
TOLERANCE
DECIMAL
ANGLE
ISSUED
HOLE DIMENSIONS
F
SCHEMATIC 401+ SERIES HTN
A
B
C
D
E
DR.
CH.
G
DRAWING NO.
SCALE
1:1
FORMING:DIMENSIONS ARE FROM
BRAKELINE TO BRAKELINE
UNLESS OTHERWISE NOTED
H
J
RTG.
0510653
Figure 13 — Electrical Diagram, 401-HTN PLUS
41
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SCHEMATICS
CUSTOMER TO SUPPLY RATED
VOLTAGE/PHASE/Hz, AS SPECIFIED
PER ORDER, TO DISCONNECT SWITCH.
ALL POWER SUPPLIED TO EACH CONNECTION
POINT MUST COMPLY WITH ALL LOCAL
ELECTRICAL CODES.
TO CUSTOMER RECEPTACLE
115V 60Hz
BLK
WHT
GND
2
1
1
8
2
2
MSW
34
CLT
ON
1
6
NO
NO
NC
4
4
8
8
8
8
CAM 1
TM
NC
1CR
7
NO
CAM 9
NC
WASH/
13
5
START CW
START CCW
MAIN
BLU
RED
BLK
OFF
/RINSE
1
2
NO
CAM 3
NC
SRC
L
S
9
9
12
5
NO
CAM 2
NC
14
DRAIN
15
M
15
3
4
5
NO
WHT
GRN
19
2
2
TP
CAM 5
F V
NC
8
(IF USED)
DP
20
NO
NC
2
2
20
D V
CAM 4
CAM 8
CAM 6
GND
GND
8
8
8
8
16
NO
NC
21
22
23
2
2
2
DM
16
17
PSDR
34
5
(IF USED)
RM
NO
NC
17
18
18
PSS
NO
NC
SM
CAM 7
DSS
1
1
50
2
1CR
BLK
BLU
BLACK
BLUE
PSS
ICR
DSS
RM
PRIME SWITCH SANITIZER
RELAY
CLT
DM
CYCLE ON LIGHT
DETERGENT MOTOR
DP
RL
DV
DRAIN PUMP
RELAY
(IF USED)
CAM 1
CAM 2
HOMING
REED SWITCH
PUMP MOTOR
RINSE MOTOR
(IF USED)
DRAIN VALVE
SRC
CURRENT OPERATED START RELAY COIL
CAM 3
CAM 4
CAM 5
PUMP MOTOR REVERSING
DRAIN
FILL
FV
FILL VALVE
GROUND
GREEN
SM
TM
SANITIZER MOTOR
TIMER MOTOR
GND
GRN
HTLS
CAM 6
RINSE
TP
THERMAL PROTECTOR
WHITE
SKH
AUG
RELEASED TO
PRODUCTION
HIGH LIMIT THERMOSTAT
CAM 7
CAM 8
SANITIZER
WHT
WHTR
WTS
A
01-03
DETERGENT
MSW
MAIN SWITCH ON/FILL OFF/DRAIN
WATER HEATER
WATER THERMOSTAT
BY
CH
REV ECN
DESCRIPTION
DATE
PSDR
PRIME SWITCH DETERGENT, RINSE
CAM 9
CYCLE
TOLERANCE
DECIMAL
ANGLE
ISSUED
HOLE DIMENSIONS
F
SCHEMATIC 401+ SERIES LOW TEMP
A
B
C
DR.
G
DRAWING NO.
SCALE
1:1
CH.
FORMING:DIMENSIONS ARE FROM
BRAKELINE TO BRAKELINE
UNLESS OTHERWISE NOTED
H
J
D
E
RTG.
0510654
Figure 14 — Electrical Diagram, 401-LT PLUS
42
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMING CHARTS
00042M2
TIMING CHART 401-HTM2
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
CAM
TIME IN SECS
HOMING
CAM
1
2
WASH PUMP
FORWARD=WASH
WASH PUMP
REVERSE=DRAIN
2
WASH PUMP
REVERSING CAM
3
4
5
6
7
8
9
DRAIN VALVE
DRAIN PUMP OPTIONAL
FILL VALVE
RINSE
OPTIONAL
PUMP
DETERGENT
PUMP
AUTO-FILL
DRAIN
RINSE
SENTRY
If booster thermostat is calling for heat,
cam 9 will pause wash cycle until it reaches
82 C/180 F.
N
C
N
O
COM.
TIMER
SWITCH
DETAIL
9 8 7 6 5 4 3 2 1
TIMER MOTOR
LOCKING SCREW
TIMER ASSEMBLY 401-HTM2
Figure 15 — Timer Chart and Diagram,
401-HT PLUS, 401- HTN PLUS
43
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMING CHARTS
00043M
TIMING CHART 401-LTM2
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
CAM
TIME IN SECS
HOMING
CAM
1
2
WASH PUMP
FORWARD=WASH
WASH PUMP
REVERSE=DRAIN
2
WASH PUMP
REVERSING CAM
3
4
5
6
7
8
9
DRAIN VALVE
DRAIN PUMP
FILL VALVE
RINSE
PUMP
SANITIZER
PUMP
DETERGENT
PUMP
AUTO-FILL
DRAIN
N
C
N
O
COM.
TIMER
SWITCH
DETAIL
8 7 6 5 4 3 2 1
9
TIMER MOTOR
LOCKING SCREW
TIMER ASSEMBLY 401-LTM2
Figure 16 — Timer Chart and Diagram, 401-LT PLUS
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|