Model MK-Manta I
Core Drill
Owner’s Manual
Parts List &
Operating
Instructions
CAUTION
READ SAFETY
AND GENERAL
INSTRUCTIONS
CAREFULLY
BEFORE USING
SAW FOR THE
FIRST TIME.
please record the serial number of
your drill in this block.
serial number
For your one (1) year warranty to
be effective, complete the warranty
card (include the serial number) and
mail it in as soon as possible.
Manual Part No. 161115
Revision 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
General Safety Instructions for the MK-Manta I Core Drill
For your Safety!
These safety precautions should be followed at all times. Failure to follow these
safety precautions could result in injury to yourself and others. Safety is a
combination of operator common sense and alertness at all times when this drill
rig is being used.
For your own safety and protection, do not attempt to operate the drill until it is
completely assembled and installed according to the instructions, and until you
read and understand all safety and operating instructions.
Take time to read and understand fully the owners manual and all safety labels
attached to the core drill.
Use safety equipment. Everyone in the work area should wear safety goggles
or glasses with side shields complying with current safety standards. Wear
hearing protection during extended use and a dust mask for dusty operations.
Hard hats, face shields, safety shoes, etc. should be used when specified or
necessary.
Use the right tool. Do not use a tool or attachment to do a job for which it is not
recommended. Do not alter the tool.
Keep your work area clean and safe to avoid accidents. Maintain a safe zone
and keep all visitors at a safe distance from the work area.
Always insure that the switch is off before plugging unit into electrical power.
Never leave the drill running unattended. Turn power off.
Do not over reach, maintain control. Keep proper footing and balance at all
times. Maintain a firm grip. Use extra care when using the tool on ladders,
roofs, scaffolds, etc.
Maintain all tools with care for the safest and best performance.
Should any part of this drill become missing or damaged, or any component fail
to perform properly, shut off the drill and unplug the power source. Replace the
missing, damaged, and/or failed part before resuming operations.
Always keep alert. Do not allow familiarity (gained from frequent use) to cause
a careless mistake. Always remember that a careless fraction of a second is
sufficient to inflict serious injury.
Think Safety The operation of any power tool can result in foreign objects
being thrown into the eyes causing severe damage. Use safety goggles to
comply with ANSI Z87.1.
FORESIGHT IS BETTER THAN NO SIGHT
2
Revision 03/05, Effective Date March 2, 2005
MANTA I
Download from Www.Somanuals.com. All Manuals Search And Download.
A safety message informs you about potential hazards that could hurt you or
others. Each safety message is preceded by one of the three words: Danger,
Warning, or Caution.
Safety Messages
! DANGER
You WILL be KILLED or SERIOUSLY injured if you don’t follow instructions.
! WARNING
You CAN be KILLED or SERIOUSLY injured if you don’t follow instructions.
! CAUTION
You CAN be injured if you don’t follow instructions.
Hazard Symbols
Additional information as to the nature of the hazard is provided by the following
hazard symbols, which appear throughout the manual in conjunction with safety
messages.
Electrical Shock!
Never touch electrical wires or
components while the drill is running. They can be sources of electrical shock
which could cause severe injury or burns.
on
Accidental Starts!
Before performing any maintence or service on this equipment, always turn
the switch off and unplug the drill from the power source to prevent accidental
starting.
Rotating Parts!
Keep hands, feet, hair, and clothing away from all moving parts to prevent injury.
Other important messages that are designed to help prevent damage to your
MK Diamond Manta Core Drill, other property, or the environment, are preceded
by the word notice.
Damage Prevention
Messages
Notice: Your MK-Manta I Core Drill or other property could be damaged if you
don’t follow instructions.
Safety labels contain important safety information. Please read them carefully.
These labels are considered a permanent part of your drill. If a label comes off
or becomes hard to read, contact MK Diamond or your dealer for replacement.
Safety Labels
3
Revision 03/05, Effective Date March 2, 2005
MANTA I
Download from Www.Somanuals.com. All Manuals Search And Download.
Manta I Core Drilling Machine
Drill Features
The MK-Manta I Core Drill is a powerful all-purpose drilling rig that is designed
to drill holes, up to 12 inches in diameter (14 inches with the 2 inch spacer), in
all types of concrete slabs, floors, walls, and ceilings. The Manta is designed for
easy anchoring using masonry anchors. A secondary vacuum base is provided
to facilitate quick and easy anchoring to smooth floor surfaces.
The Manta is designed for use with a variety of motors. All motors are powerful
two or three speed units that provide the correct cutting speed over a range
of diamond drill sizes. Some models utilizes a shear-pin system for motor
protection, while some others utilize a slip-clutch. See the Drilling Speeds
section of this manual.
Motor
The carraige, column and base assembly of the Manta I Core Drill is the strong,
sturdy drilling platform that provides the rigidity needed to quickly drill accurately
placed, straight, smooth holes in all types of concrete. The Manta’s base is
slotted to provide easy anchoring of the drill, in a variety of drilling situations,
with a single masonry anchor. The slot also allows more than one hole to be
drilled from a single anchor location. The base contains four leveling screws to
insure accurate hole alignment even on uneven concrete surfaces. The base
also has a cast in handle and a set of wheels to provide easy transport.The
carraige travel is controlled by a strong rack and pinion gear-system, that can
be locked at any point on the column. The slidding handle allows the operator
to easily control the drilling pressure and speed. At the top of the column is
a strong jack-screw that allows for additional bracing to overhead or opposite
surfaces.
Carraige,
Column and
Base
The vacuum base and pump provide quick and reliable mounting to smooth
concrete slab and floor surfaces. The powerful vacuum pump provides 25 PSI of
holding power which equates to over 1800 pounds of force, holding the Manta
securely, for safe, accurate drilling. The pump has a quick disconnect connector
on the hose, as well as an ergonomic handle, to provide ease of transport. The
vacuum base also features leveling screws, a cast-in handle and six inch (6”)
wheels.
Vacuum
Base and
Pump
The water system for the Manta is a simple hose hook-up and shut-off valve
that provides water under pressure to the diamond drill bit. The water travels to
the center of the bit through the water swivel and spindle to insure that water is
supplied to the cutting end of the bit, even in deep drilling operations.
Water System
4
Revision 03/05, Effective Date March 2, 2005
MANTA I
Download from Www.Somanuals.com. All Manuals Search And Download.
Carefully cut through the carton approximately 6 inches from the bottom using a
box cutter or other safety knife, and lift away the top portion of the box. Remove the
Accessory Pack, Vacuum Pump and Manta Core Drill. Open the accessory pack and
check each item with the contents list and illustration below, making certain that all
items are accounted for and in good condition before discarding any packing material. If
there are any missing or damaged parts, call our toll free number 1-(800)-421-5830 for
instructions before proceeding with the assembly.
Unpacking
CONTENTS
Contents of the carton: Manta (including column, carraige, both bases and motor),
Vacuum Pump and Accessory Pack.
In the Accessory Pack you will find: Control box, leveling screws (8), feed handle (1)
and knobs (2), vacuum base gasket, wrench, Manta manual, Manta warranty card,
motor manual and motor warranty card.
Manta and Vacuum
Pump
Control Box
Vacuum Pump
Leveling Screws
Base Gasket
Feed Handle and
Knobs
Manta Manual
Warranty Card
5
Revision 03/05, Effective Date March 2, 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTA I
Assembly
! WARNING
For your own safety and protection, do not attempt to operate this drill until it is
completely assembled and installed according to these instructions, and until
you understand the machines capabilities and the potential hazards associated
with it.
Main Assembly
Step 1 The Manta I is shipped with the main part of the Manta mounted
backwards on the Vacuum base. Remove the nut and bolt that hold the main
assembly to the Vacuum base observing the following precaution. Turn the
Vacuum base around to the correct orientation, slide the small base all the way
back on the vacuum base, and reinstall the nut and bolt.
! CAUTION
When removing the nut and bolt that holds the main assembly to the vacuum
base, the Manta will tip forward. Be sure to hold the Manta when removing the
vacuum base.
To set the Manta so that it will stand up, loosen the carraige lock knob (be sure
to hold the carraige) and move the carraige down to a position where the end of
the motor spindle just touches the ground.
Step 2 Install the leveling screws (8), screwing four (4) into each base.
Feed Handle and
Meter Box
Step 3 Install the feed handles (1) and knobs (2) by screwing one knob onto
the end of the handle, then slip thru hub and attach other knob.
Step 4 Remove the Manta from the vacuum base by removing the nut and
bolt that holds the main assembly to the vacuum base. Set the Manta aside,
observing the following precaution.
Turn the vacuum base over. Press the gasket into the groove in the underside of
the base. The gasket is cut, at the factory, to the correct length, so that the two
ends will butt together once the gasket is installed.
Vacuum Base Gasket
Final Assembly
Step 5 Assemble the two pieces of the water valve, and install the valve, into
the water swivel, on the motor, just above the spindle (see motor literature).
Plug the cord from the motor into the upper outlet on the meter box (the one
opposite the motor on-off switch. The other outlet on the meter box is for the
vacuum pump.
6
Revision 03/05, Effective Date March 2, 2005
MANTA I
Download from Www.Somanuals.com. All Manuals Search And Download.
Drilling Operations
Electrical Requirements
The MK-Manta I Core Drill rig has been equipped with either a 20 Amp/115V 3
speed motor, a 20 Amp/120V 2 speed motor, or a 15 Amp/115V 2 speed motor.
The drill should be used on an electrical circuit, separate from other loads, and
protected by a 30 amp circuit breaker.
Grounding
NEMA L5-20 125 V, 20 Amp
Locking Plug and receptacle
The MK-Manta I has been provided with a 20 Amp plug (NEMA 15-20) or a 30
Amp (NEMA 15-30) locking plug depending on the model.
Grounding
blade
The MK Manta is marked “Grounding Required” and has a three wire cord and
three prong grounding plug. The plug must be connected to a properly grounded
outlet (see figure below). If the tool should electrically malfunction or break
down, grounding provides a low resistance path to carry electricity away from
the user, reducing the risk of electrical shock.
Cover of grounded outlet
box
The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding systems and must never be attached
to an electrically live terminal.
NEMA L5-30 125 V, 30 Amp
Locking Plug and receptacle
Grounding
blade
Your tool must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet
should look like those in the figure to the left.
Cover of grounded outlet
box
! WARNING
Improperly connecting the grounding wire can result in the risk of electric shock.
Check with a qualified electrician if you are in doubt as to whether the outlet
is properly grounded. Do not modify the plug provided with the tool. Never
remove the grounding prong from the plug. Do not use the tool if the cord or
plug is damaged. If damaged, have it repaired by an authorized service facility
before use. If the plug will not fit the outlet, have a proper outlet installed by a
qualified electrician. The use of a circuit protected by a ground fault interrupter
(GFI) is highly recommended.
Use extension cords of the proper cable size, referring to the following chart.
Extension Cords
Cord Length
25 feet
#10
50 feet
#8
75 feet
#6
Wire Size (AWG)
! WARNING
Never use an extension cord smaller than shown in the chart. Be sure your
extension cord is properly wired and in good electrical condition. Always replace
a damaged extension cord or have it repaired by a qualified electrician before
using it.
Protect your extension cords form sharp objects, excessive heat and damp or
wet areas.
Notice: Using an extension cord with inadequately sized wire causes a serious
drop in voltage, resulting in loss of power and possible tool damage.
7
Revision 03/05, Effective Date March 2, 2005
MANTA I
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Use a concrete anchor. Use either a 1/2 or 5/8 concrete anchor to secure
the base to the work surface. Always be sure to level the rig. Using a concrete
anchor, insert a bolt through the slot located on the base and tighten the bolt
firmly in the anchor.
Securing the Rig
Recommended
Methods
! WARNING
It is essential to always secure the rig to the work surface to help prevent
personal injury and also to protect the rig. An unsecured rig could rotate during
drilling and possibly cause injury. It could also cause the bit to chatter against
the work surface or bind in a hole, which can fracture the diamond segments.
B. Vacuum base. The MK-Manta I Core Drill Rig is equipped with a vacuum
base. This base is designed to provide approximately 1800 pounds of total
holding power. In order to provide the most rigidity to your core rig the unit
should be used on a relatively smooth surface such as concrete. (If the surface
is too porous or rough the vacuum mount may not hold securely.)
1. Turn the vacuum pump on and step on the vacuum base until a vacuum is
created and the base adheres to the work surface.
2. Level the rig using the leveling bolts. Use a minimum amount of adjustment to
the leveling bolts to avoid breaking the vacuum seal.
The vacuum gauge should read approximately 25 pounds per square inch
(PSI) of pressure. If the gauge reads 20 PSI or less, check the work surface
for conditions which may interfere with adequate suction such as cracks, dirt or
debris on a porous surface.
! WARNING
Do not drill if the gauge reads less than 20 PSI. Do no use vacuum base on
cracked, uneven, porous or vertical surfaces.
C. Additional support. For added rigidity, you may use a telescoping extension
assembly in conjunction with a concrete anchor or vacuum base. To use a
telescoping assembly, first level the rig with the leveling screws. Secure the
rig with an anchor or the vacuum base. Place the top flange of the extension
against a ceiling or wall and place the other end on the jack screw of the
column. The assembly is adjustable up to 14 feet. Use the jack screw to tighten
the assembly and to make small adjustments.
The MK-Manta I features two speed motors by Milwaukee and a three speed
motor by Eibenstock. Specifications for the different motors are listed in the
following table.
8
Revision 03/05, Effective Date March 2, 2005
MANTA I
Download from Www.Somanuals.com. All Manuals Search And Download.
Drilling Speeds
Manufacturer
Model #
AMP
Volts Speed(RPM)
Suggested Dia. in
Medium Aggregate
Eibenstock
EBM
300/3 P
20
120
Low – 270
Medium – 700
High – 1250
Low – 300
High – 600
Low – 375
High – 750
Low – 450
High – 900
Low – 450
High – 900
Low – 500
High – 1000
Low – 4”
Medium – 2”-6”
High – 3/4”-4”
Low – 4”
Milwaukee
Milwaukee
Milwaukee
Milwaukee
Milwaukee
4004
4090
20
15
20
20
15
120
120
120
120
120
High – 14”
Low – 5”-8”
High – 2 1/2”-5”
Low – 6”-10”
High – 2”-6”
Low – 6”-10”
High – 2”-6”
Low – 1 1/4”
High – 5”
4094
4096
4097-20
The MK-Manta I will operate in either a high or low gear speed. This speed combined
with applied pressure provides the cutting action for the core bit. Speed selection and
pressure are determined by hardness of material, aggregate size and grade of diamond
core bit. Generally, harder material and larger aggregates require more speed and
pressure. Use low speed for large diameter bits and high speed for small diameter bits.
Changing of the speeds is accomplished by using the speed shift lever built into the
gear case.
LOW
HIGH
Notice: Change the gears only when the motor is off.
All building materials and work surfaces are composed of aggregate of various size.
Aggregates are materials such as gravel or crushed stone. The size of the grains and
the hardness of the material affects the speed of drilling. Most building materials contain
some type of steel reinforcements. All MK bits are designed to cut through these types
of reinforcing steel. However, bits should never be used for drilling solid steel plates.
Proper selection of the diamond core bit should be based on material to be drilled and
performance requirements.
Drilling Pressure
and the Ammeter
Steady, even pressure assures accurate holes and longer bit life. Always maintain
consistent pressure so that the bit is constantly cutting.
A
PS
Notice: Too much pressure will damage the bit and motor. Too little pressure will
glaze over the diamonds, reducing cutting efficiency and prematurely wearing the bit.
The ammeter is the gauge on the Control Box. It provides pressure feedback information
during drilling, allowing the operator to help prevent motor overload and premature bit
wear. The green area is the operating range, and the red area is the overload range.
Generally, the operator should keep the ammeter needle in the upper area of the
operating range for large diameter bits, and in the lower green area for small diameter
bits. If the bit contacts steel reinforcing rods, the needle on the ammeter may jump
slightly showing a heavier load. If this occurs, do not decrease pressure or you may
damage the diamonds. The Manta may be operated with the ammeter needle into the
red area for the short period of time that it takes to cut through a steel rod.
15
18
20
Water Supply
An adequate supply of clean water is necessary for drilling. Connect the water supply
hose to the hose fitting on the output of core drill motor. Take precautions that the water
supply will not be interrupted during the drilling operations.
Notice: If a bit is run dry it can be ruined in a few seconds.
9
Revision 03/05, Effective Date March 2, 2005
MANTA I
Download from Www.Somanuals.com. All Manuals Search And Download.
It is essential that the carraige fits snugly on the column to prevent the motor or
bit from wobbling during drilling. Through normal use the carraige may loosen
from the column and begin to wobble. Before drilling, always make sure the
carraige is rigid by trying to wiggle it with your hand. If the carraige is secure it
should not move. If it does move, tighten the adjustment screws for the nylon
gibs that secure the carraige to the column.
Carriage Rigidity
Tighten only enough to remove the play. Do not over tighten.
Shear Pin and
Clutch Protection
The MK-Manta I Core Drill uses either a shear pin or a friction clutch to protect
the gear and motor against overload. The shear pin drives the outer portion of
the drive spindle. If the motor should overload the pin will shear. Extra shear
pins are supplied or can be ordered from MK Diamond’s Customer Service.
Tighten only enough to remove the play. Do not over tighten. Another model
features a friction clutch rather than a shear pin to protect the motor and gears.
If the motor overloads the clutch will begin to slip and the bit will stop rotating.
The clutch is factory-set and does not require adjustments. However, under
normal use, the clutch may start to slip at low torque. If this happens, refer to the
motors Owner’s Manual.
Bits with permanently attached adapters simply screw directly onto the threads
of the drill spindle. Ensure that the end of the bit butts up squarely against the
shoulder on the spindle.
Mounting Bits
The MK-Manta I has a 1 1/4”-7 thread. For bits with other threads, use a shaft
coupling. After a bit has been mounted, turn the power on and check that there
is a minimum of run-out or wobble.
! WARNING
To reduce the risk of injury, always unplug tool before attaching or removing
accessories. Only use specifically recommended accessories. Others may be
hazardous.
! WARNING
Drilling Procedure
When drilling through concrete floors, the core will generally drop from the
diamond bit. Caution should be provided for people and property below the
drilling area.
1. Ensure that you have read and fully understand the complete operation of the
MK-Manta I you have purchased prior to commencing drilling operations.
2. Select and install a diamond core bit appropriate for the job. Note: Grease the
bit threads to help prevent the bit from seizing on the spindle due to rust.
3. Select either high or low gear speed according to the chart in the Drilling
Speeds section of this manual. (Do not shift speed when motor is on.)
4. Connect water hose to water swivel.
5. Secure the rig as described in the Securing the rig section of this manual.
10
Revision 03/05, Effective Date March 2, 2005
MANTA I
Download from Www.Somanuals.com. All Manuals Search And Download.
! WARNING
If using the vacuum base, do not continue operations unless the vacuum gauge
reads more than 20 inches of mercury. Normally, the gauge will read 23 inches
or more.
6. Turn the motor switch on the Control box ON. Turn the water ON so that an
adequate flow of water is supplied through the water swivel, to the bit. Hold the
handle and slightly loosen the carriage lock knob. Slowly rotate the handle to
lower the bit into the work piece - apply steady even pressure.
Note: To prevent the bit from wandering, always use a light load to start the
hole and wait for the diamond tip of the bit to penetrate the work surface before
increasing the load.
7. Use consistent pressure so that the bit cuts consistently. Insufficient pressure
will cause the diamond core bit to glaze over. Too much pressure will overload
the motor and crush the diamonds. Use the ammeter on the Control box as a
guide for proper pressure.
! CAUTION
If the rig shifts during drilling, stop the motor, reposition the rig, and resume
drilling.
8. Monitor the water flow. If the water flow is adequate, the water leaving the cut
should be slightly sludgy. When cutting metal rebar, the water should have a
gray metal coloring.
Notice: When drilling into prestressed concrete the bit may cut into the hardened
steel cable under tension. As the bit cuts through each strand, the tension in the
cable is released. The diamond segments on the bit crown can be damaged by
the loose wires. The best prevention for bit damage is to use a core bit designed
especially for drilling in prestressed concrete.
9. When the cut is complete, keep the drill motor on and rotate the handle to
bring the bit up out of the hole. The bit may become stuck if the motor is turned
off before the bit is completely clear of the hole. Once the bit is clear of the hole,
tighten the carraige lock knob, turn off the motor and the water supply.
Note: Normally the core will drop out of the bit, and remain in the hole. However,
in cases where the core sticks in the bit, it is sometimes necessary to push
the core up and down with the water running to allow the core to drop out.
Sometimes very light tapping on the barrel of the bit with a piece of wood will
loosen the core.
! CAUTION
Perform this action only with the motor turned off and the unit unplugged
to prevent accidental starting and injury. Exercise extreme caution in hand
placement when removing a stuck core, as it can be heavy and inflict injury.
11
Revision 03/05, Effective Date March 2, 2005
MANTA I
Download from Www.Somanuals.com. All Manuals Search And Download.
When drilling holes that are longer than the core bit, follow the steps below.
Deep Drilling
1. Begin drilling the hole as usual. When you have drilled to the length of the bit,
retract the bit from the hole and turn off the motor and water as usual.
2. Break off the core by driving a chisel or slender wedge into the circular kerf.
Remove the core using core tongs, bent music wire or anchor bolts.
3. After removing the core, insert the bit carefully into the hole, attach a bit
extension to the bit and core drill rig, then continue drilling as usual.
Periodic maintenance, including cleaning, lubrication and inspection for wear
and damage are routine servicing procedures. Following the procedures as
outlined can prevent serious damage or malfunctioning of the machine, and aid
in preserving the useful life of core drill bits.
Maintenance
on
! CAUTION
Before performing any maintenance to the MK-Manta I, always unplug the unit
from the electrical power source. Be sure the On-Off switches are in the Off
position, after servicing, and before plugging the unit back in.
Clean the machine after use, being careful to remove dust and slurry from the
motor, vents, carraige and column. Keep tool handles clean, dry and free of oil
and grease. Use only mild soap and a damp cloth to clean this tool since certain
cleaning agents and solvents are harmful to plastics and other insulated parts.
Cleaning
! WARNING
Never use flammable or combustible solvents around tools.
Through normal use, the rubber gasket on the underside of the vacuum base
can become worn, requiring replacement. Periodically check the gasket for
wear. If replacement is required, clean the groove in the base before installing a
new gasket.
Vacuum Base Gasket
12
Revision 03/05, Effective Date March 2, 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTA I
When trouble occurs, be sure to check the simple causes which, at first, may
seem too obvious to be considered. Refer to the table below for problems and
their possible causes.
Troubleshooting
PROBLEM WHAT TO DO?
INDICATION
CAUSE
SOLUTION/ RECOMMENDATIONS
1. Check fluid
return.
Fluid not muddy.
Evidence of steel
cuttings
Drilling in steel
reinforcement
Adjust drilling parameters to
recommendations for reinforcement
2. Check motor
speed range
Speed not correct for See recommended
the bit size used
speeds
Bit worn out.
Replace with new bit
Increase bit load
Low
Penetration
Rate Under
Prevailing
Drilling
Paramters
Insufficient bit load
Diamond without
exposure.
(flush with matrix)
Rotated with
high RPM on
reinforcement
Reduce RPM, or resharpen bit
3. Check wear
picture of bit
face
Break core, clean bottom of hole or
reduce RPM and drill with increased
bit load
Loose material at
bottom of hole
Not enough fluid
pumped. Cuttings
burnt to matrix.
Diamonds prevented
from cutting
Clean bit face by sharpening methods
such as drilling dry at low RPM in a
concrete block 3/8” deep max.
Increase water flow rate
Face of bit
plugged with
cuttings
Steel cuttings stick to
bit face. Diamonds
prevented from
cutting
Clean bit face by drilling in concrete
block.
Reduce RPM
Face of bit
covered with steel
Steel cuttings stick
to bit face.
Bit load too low
Increase bit load
Wear picture of
polished diamonds
Bit speed too high
Use lower speed; increase bit load
Heavy
Wear at
Steel Tube
Worn or open guide
ways on cradle.
Borehole is getting
undulated
Adjust guidance on carraige
Deep grooves.
Protruding steel.
Spindle is offset.
Bit out of true
Adjust guidance on carraige
Nicks or dirt on mounting faces
Bit is deformed.
Replace bit.
Heavy Wear.
Poor cleaning of
abrasive cuttings.
Improve flushing.
Crown clearance
worn out.
Replace bit
No return of Check where
If Leaking can be tolerated; continue
drilling with increased attention.
fluid
fluid is leaking.
13
Revision 03/05, Effective Date March 2, 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTA I
SOLUTION/ RECOMMENDATIONS
PROBLEM
WHAT TO DO?
INDICATION
Step 1: Apply wrench and rotate
bit in both directions while bit is
under tension. If not successful:
Loose material
(cut steel or
aggregates) is
blocking between
core and bit or
between borehole
and bit.
Bit Stuck
Step 2: Try to over drill a hole
slightly larger than the stuck bit.
1. Try to raise
bit, if impossible: Drill moved during
drilling (poor
Disconnect bit and remove,
break core. Start over with
improved fastening of machine.
fastening).
2. Stop rotation
Bit deviates, guide
ways on cradle
Disconnect machine, adjust
guidance.
have too much
clearance.
Replace bit.
No clearance
between tube I.D.
or O.D. and crown
I.D. or O.D.
Use recommended speed for
the bit diameter used. Raise bit
when it begins to load down.
Feed bit slowly when chattering
begins.
Shear Pin Fail 1. Stop rotation
2. Raise bit
Drill impacted
to stall at lower
speeds.
If within one (1) year from the date of purchase, this MK Diamond drill
fails due to a defect in material or workmanship, MK will repair it, free
of charge, by returning the unit to the dealer where it was purchased.
This warranty DOES NOT cover normal wear or damage resulting from
operator abuse. In no event shall MK Diamond Products, Inc. be liable
for consequential damages arising out of the failure of any product if
operating improperly. Selected components such as motors/engines
are excluded from this warranty and are subject to the manufacturer’s
warranty. Each manufacturer carries its own warranty conditions which
are listed on the literature accompanying the motor/engine at the time
of purchase. MK Diamond Products may act as a warranty station
for the motor/engine repairs based on individual agreement with the
manufacturer. This warranty is in lieu of all other warranties expressed or
implied.
Warranty Information
14
Revision 03/05, Effective Date March 2, 2005
MANTA I
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTA I COMBO EXPLODED VIEW AND PARTS LIST
EXPLODED VIEW
15
Revision 03/05, Effective Date March 2, 2005
MANTA I
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTA EXPLODED VIEW (cont...)
16
Revision 03/05, Effective Date March 2, 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTA I
MANTA EXPLODED VIEW (cont...)
17
Revision 03/05, Effective Date March 2, 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTA I
MANTA EXPLODED VIEW (cont...)
18
Revision 03/05, Effective Date March 2, 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTA I
MANTA PARTS LIST
PARTS LIST:
Item
A
A1
A2
A3
A4
A5
A6
A7
Description
Assembly, M1 Base, Vacuum
Base, M1 Vacuum
Screw, ꢀ-13 x 3 ꢀ Hex Hd. Cap, Full Thread
Gasket, Neoprene
Fitting, ꢁ MNPT x 3/8 Barb
Wheel 6”
Screw, 1/2 x 1 3/4 Socket Head Shoulder
Washer, ꢀ SAE Flat
Foot, Base Support
Screw, 3/8-16 x 2 ꢁ Hex Head Cap
Washer, 3/8 SAE Flat
Nut, 3/8-16 Hex Nylok
Stud, ꢀ-13 x 4 Clamping
Washer, Plate ꢁ x 2 x 2
Nut, ꢀ-13 Flange
Assembly, M1 Base, Anchor
Base, M1 Anchor
Screw, ꢀ-13 x 3 ꢀ Hex Hd. Cap, Full Thread
Wheel, Dia. 1 5/8 x 7/8
Sleeve Bearing
Screw, ꢁ-20 x 2.0, Socket Head Cap
Foot, Base Support
Screw, 3/8-16 x 2 ꢁ Hex Head Cap
Washer, 3/8 Flat
Qty
1
1
4
1
1
2
2
2
2
2
2
2
1
1
1
1
1
4
2
2
2
2
2
2
2
1
1
1
1
1
1
2
3
8
8
8
8
1
1
1
4
6
1
2
2
4
1
1
1
2
2
6
1
MK p/n
n/a
155753
158284
154543
154659
157434
158390
150924
158389
153529
150923
152505
155124
154613
155125
n/a
155755
158284
158396
158458
158394
158389
153529
150923
152505
157730
155576
157914
n/a
155757
158348
137711
157317
157318
154448
157521
157519
151681
151915
157438
151049
154226
157440
157523
154334
159336
158428
158274
158276
152587
152591
153681
154489
A8
A9
A10
A11
A12
A13
A14
AA
AA1
AA2
AA3
AA4
AA5
AA6
AA7
AA8
AA9
AA10
AA11
AA12
D
D1
D2
D3
D4
D5
D6
D7
D8
Nut, 3/8-16 Hex Nylok
Label, Manta Serial Tag (not shown)
Label, Caution, Safety (not shown)
Label, MK, Adhesive (not shown)
Assembly, Carriage 2 ꢀ”
Body, Carriage
Shaft, Gear, Short
Bearing
Plate, Adjustment
Slide, Carriage
Screw, 6-32 x 1/2 Flat Head Phillips Machine
Screw, 6-32 x 3/8 Flat Head Phillips Machine
Nut, 6-32 Nylok Hex
Knob, Davies ꢁ-20 x ꢂ
Washer, ꢁ SAE Flat
D9
D10
D11
D12
D13
D14
D15
D16
D17
E
E1
E2
E3
E4
Back, Carriage
Screw, 1/4-20 X 1 Socket Head Cap
Screw, ꢁ-20 x 5/16 Socket Head Set
Handle, Carriage
Screw, 1/4-20 X ꢂ Pan Head Phillips
Label, MK USA
Screw, 1/4-20 X 1 ꢁ Socket Head Cap
Assembly, Control Box, Fixed, Dual Switch 120V
Box, Control, Fixed
Cover, Control Box, Fixed, Dual Switch
Screw, ꢁ-20 x ꢂ Socket Head Cap
Washer, ꢁ Split Lock
E5
E6
Screw, 10-24 x 5/8 Self Tapping (phillips)
Ammeter 120V
19
Revision 03/05, Effective Date March 2, 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTA I
MANTA PARTS LIST (cont...)
E7
E8
E9
Switch, Toggle
Receptacle, Flanged 15A / 125V
Cord, Power
Connector, Cord
Receptacle
Transformer
Screw, 6-32 x ꢀ Pan Head
Plug, Twist-lock
Wire Harness (not shown)
Cover, Toggle Switch
Assembly, Control Box, Single Switch 120V
Box, Control, Single Switch
Cover, Control Box, Single Switch
Screw, ꢁ-20 x ꢂ Socket Head Cap
Washer, ꢁ Split Lock
Screw, 10-24 x 5/8
Ammeter 120V
Switch, 30A Toggle
Cord, Power
Connector, Cord ꢀ
Receptacle, Flanged Twist-lock 20A / 125V
Plug, Twist-lock
Transformer, Current
Screw, 6-32 x ꢀ Pan Head
Wire Harness
RTV Silicon Adhesive Sealant
Cover, Toggle Switch
Assembly, Column
2
1
3’
1
1
1
2
1
1
2
1
1
1
2
2
6
1
1
3’
1
1
1
1
2
154491
154473
154494
151307
157375
154490
153459
154556
154715
154301
158430
158385
158387
152587
152591
153681
154489
154491
154494
151307
157375
154556
154490
153459
154715
n/a
E10
E11
E12
E13
E14
E15
E17
EB
EB1
EB2
EB3
EB4
EB5
EB6
EB7
EB8
EB9
EB10
EB11
EB12
EB13
EB14
EB15
EB16
F1
1
.25 oz.
1
154301
n/a
F1
F3
F4
F5
F6
F7
F8
GB
GB1
GB2
GB3
GB4
GB5
GB6
GB7
GB8
GB9
GB10
GB11
GB12
GB13
GB14
GB15
GB16
H
Manta, Core Drill Column (w/Gear Rack)
Screw, 10-32 X ꢀ Socket Hd. Cap
Washer, #10 Split Lock
Screw M22 x 1.25 Jack
Screw, 1/2-13 X 3 ꢀ Hex Head Cap
Washer, 1/2 Split Lock
Washer, 1/2 SAE Flat
Assembly, Vacuum Pump w/ Handle 120V
Pump, Vacuum 120v
Filter, Water
1
4
4
1
2
2
2
1
1
1
1
3
2
1
6’
1
2
2
1
1
4
4
4
4
1
1
158425-2
157525
153684
157445
154574
153524
150924
154741
154475
154476
154477
152598
154497
154488
154656
154617
154659
154660
154495
139949
151052
154496
154657
151893
n/a
Gauge, Vacuum
Nipple, 1/4 MNPT X Close
Fitting, 1/4 FNPT X 1/4 FNPT X 1/4 FNPT Tee
Valve, 1/4” Pettcock
Hose, 3/8 I.D. Air
Coupler Body, 1/4 FNPT
Fitting, 1/4 MNPT X 3/8 BARB
Ferrell, Crimp
Base, Vacuum Pump
Handgrip, 3/4 X 4 9/16 Black
Screw, 10-32 X 1/2 Phillips Pan Head Cap
Foot, Rubber
Screw, 1/4-20 X 3/4 Flat Head Phillips Cap
Nut, 1/4-20 Hex
Assembly, Handle, Slip
Hub, Slip Handle
H1
157321
20
Revision 03/05, Effective Date March 2, 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTA I
MANTA PARTS LIST(cont...)
H2
H3
H4
H5
K
K1
K2
K3
K4
LA
LA1
LB
LB1
LD
LD1
LE
LE1
LF
LF1
LJ
LJ1
M
M1
M2
M3
M4
MA
MA1
MA2
MA3
MA4
MB
MB1
MB2
MB3
MB4
Spoke, Slip Handle
Knob, Ball ꢀ-20 Female
Screw, 1/4-20 X ꢂ Thumb
Screw, ꢁ-20 X 1/4 Socket Head Set
Assembly, Accessory Pack (not shown)
Carton, Accessory Pack
Owner’s Manual, MK-Manta 1 Core Drill
Card, Warranty
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
4
1
1
4
1
4
1
1
4
1
4
157322
154486
157432
157528
n/a
157323
161115
155859
155333
n/a
154633
N/a
155540
n/a
159263
n/a
159264
n/a
MK Sell Sheet
Assembly, Motor, Milwaukee 4094
Motor, Milwaukee 4094 - Shear Pin, 20A/120V
Assembly, Motor, Milwaukee 4096
Motor, Milwaukee 4096 - Slip Clutch, 20A/120V
Assembly, Motor, Milwaukee 4004
Motor, Milwaukee 4004 - Slip Clutch, 20A/120V
Assembly, Motor, Milwaukee 4097-20
Motor, Milwaukee 4097-20 - Slip Clutch, 15A/120V
Assembly, Motor, Milwaukee 4090
Motor, Milwaukee 4090 - Shear Pin, 15A/120V
Assembly, Motor, Eibenstock EBM 300/3 P
Motor, Eibenstock EBM 300/3/P - Slip Clutch, 20A/120V
Assembly, ꢂ” Motor Mount Plate, Hybrid, Milwaukee
Casting, Motor Mount Plate, Hybrid
Screw, 3/8-16 x 1 ꢁ, Socket Hd. Cap
Key, 3/8 x 3/8 x 5
Screw, ꢁ-20 x 1.0, Socket Hd. Cap
Assembly, ꢂ” Motor Mount Plate, Hybrid, CB748
Casting, Motor Mount Plate, Hybrid
Screw, 3/8-16 x 1 ꢁ, Socket Hd. Cap
Key, 3/8 x 3/8 x 5
Screw, ꢁ-28 x 1.5”, Socket Hd. Cap
Assembly, ꢂ” Motor Mount Plate, Hybrid, Ebinstock
Casting, Motor Mount Plate, Hybrid
Screw, 3/8-16 x 1 ꢁ, Socket Hd. Cap
Key, 3/8 x 3/8 x 5
155976
N/a
158754
n/a
158412
157529
157520
151049
n/a
158412
157529
157520
154684
n/a
158412
157529
157520
157530
Screw, M8 x 1.25 x 25mm, Socket Hd. Cap
Optional Accessories:
N
N
N2
N3
Assembly, 2”, Spacer Block Milwaukee
Spacer Block, 2” Milwaukee
Screw, 3/8-16 x 3 ꢁ, Socket Hd. Cap
Key, 3/8 x 3/8 x 5
1
1
4
1
n/a
154721
161118
157520
21
Revision 03/05, Effective Date March 2, 2005
MANTA I
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPAIR PARTS
please have the following information ready before calling:
SERIAL NUMBER OF YOUR SAW
MODEL NUMBER OF SAW
WHERE PURCHASED AND WHEN
PART NUMBER
PART DESCRIPTION
all parts listed may be ordered from your local distributor or from mk diamond. If the part is not stocked
locally, call our toll free number listed below and ask for our customer service department. For technical
support call: 1 (800) 474-5594. There is a $25.00 minimum order.
RETURNED MERCHANDISE POLICY
Should you need to return any product you have purchased from MK Diamond, please observe the
following:
Our customer service department should be contacted for approval to return merchandise. Merchandise
will not be accepted without a RETURNED GOODS authorization number. All returned merchandise must be
shipped prepaid to destination. All returned merchandise must have been purchased within the previous 12
months and be in resalable condition. A restocking charge of 15% will be billed.
PARA ORDENAR PARTES DE REPUESTO
Sírvase tener lista la siguiente información antes de llamar:
Número de serie de la sierra
número de modelo de la sierra
Dónde y cuando se compró la sierra
Número de la parte
Descripción de la parte
Todas las partes listadas se pueden pedir a través de su distribuidor autorizado o directamente a MK Diamond.
Si la parte no está en existencia local, llame al número de teléfono indicado abajo y pida el departmento de
atención al cliente. Para soporte técnio, llame al 1-800-474-5594 sin cargo. El pedido mínimo es de $25.00.
POLÍTICA DE DEVOLUCIÓN DE MERCANCÍA
En caso de que sea necesrio devolver algún producto que usted haya comprado a MK Diamond, sívase observar
lo siguiente:
Usted debe dirigirse a nuestro departamento de atención al cliente para recibir una aprobación de devolución
de mercanía. No se aceptará mercancía devuelta sin el correspondiente número de pagado hasta su destino.
Toda la mercancía devuelta deberá embarcarse con flete meses anteriores y estar en condiciones de poderse
vender como nueva. Se aplicará un cargo de 15% por reintegro al almacén.
POUR COMMANDER LES PIÈCES DE RECHANGE
VEUILLEZ AVOIR LES INFORMATIONS SUIVANTES AVANT D’APPELER :
NUMÉRO DE SÉRIE DE LA SCIE
NUMÉRO DE MODÈLE DE LA SCIE
DATE ET LIEU D’ACHAT
RÉFÉRENCE
DESIGNATION DE LA PIÈCE
Toutes les pièces indiquées peuvent être commandées auprès de votre distributeur local ou auprès de MK
Diamond. Si la pièce n’est pas stockée localement, veuillez appeler notre numéro d’appel gratuit indiqué ci-
dessous et demander le service de la clientèle. Pour support technique, veuillez contacter le 1 (800) 474-
5594. Un minimum de commande 25,00 dollars US est de rigueur.
POLITIQUE DE RETOUR DE MARCHANDISES
Si vous vous trouvez dans l’obligation de retourner un produit dont vous avez fait l’achat à MK Diamond,
veuillez suivre les consignes suivantes:
Notre service de clientèle devrait être consulté pour approbation avant de retourner toute marchandise. La
marchandise ne sera en aucun cas acceptée sans numéro d’autorisation de Marchandises retournées. Toutes
les marchandises retournées doivent avoir fait l’objet de l’achat dans les 12 mois précédents et être en état
de revente. Une charge de restockage de 15% sera facturée.
MK Diamond Products, Inc.
Manual Part No. 161115
1315 Storm Parkway. Torrance, CA 90509-2803
Revision 03/05
1 (800) 421-5830
FAX 1 (310) 539-5158
Download from Www.Somanuals.com. All Manuals Search And Download.
|