OWNER’S MANUAL
GP30 LOADER
PARTS and INSTRUCTIONS
1242 ARIZONA AVE.
LARCHWOOD, IA 51241
1-800-570-8205
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
• Composite Bearing Information
• Mounting Loader on Tractor
• Dismounting Loader
• Quick-attach Instructions
• Parts Schematics
• Cylinder Packing Detail
• Loader Specifications
• Warranty
SERIAL No. of Loader Purchased _______________________
Date Purchased____________________
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPOSITE BEARING INFORMATION
FIG. A
FIG. B
Pin Seal
Bearing
Housing
Pin Seal
Bearing
FIGURE A. Your GP/GL-Series loader is equipped
with composite, greaseless bearings at all (12) pivot
points. These high-quality bearings should not be
confused with plastic bushings, sintered bushings, or
metal-backed bearings. Composite bearings are
made from an ultra-strong fiberglass composite that
has twice the compressive yield strength of plain
carbon steel. Their greaseless feature is due to a
Teflon-impregnated liner that is interwoven to the
bearing’s inside diameter. The bearings are de-
signed to last the life of the loader and the pins that
rotate in the bearings should exhibit practically no
wear.
FIGURE B. Even though the composite bearings on
your GP/GL-Series loader have excellent resistance to
dirt particles, the (4) pivot points on the bucket have
an added feature. The two lower bucket cylinder piv-
ots and the two mainframe-to-bucket pivots are
equipped with pin seals on each end of the bearing
housing. It is these four pivot points that are usually
down in the dirt and grime, but with a GP/GL-Series
loader, you won’t have to worry about pin failures
again!
FIGURE C. Should any of your bearings have to be re-
moved, this photo shows the tool that is available to remove
and install the bearings properly. They are available for pur-
chase, you just need to tell your dealer or Miller Loaders the
model of loader you have. If you’d prefer to make your own,
here are a few things to remember:
Nose
Shoulder
•
•
•
The nose should be 1/4” longer than the bearing
A 1/4” bevel on the end of the nose
The shoulder must be just slightly smaller than the out-
side diameter of the bearing
Bevel
FIG. C
•
The diameter of the nose should be about 0.005 less
than the inside diameter of the bearing
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNTING LOADER
FIG. 3
FIG. 2
FIG. 1
FIG. 4B
FIG. 4A
FIG. 4C
V-Block
Upright mast
Support shaft
Tapered
Guide Block
FIG. 7
Stand Legs
Stand Legs Stored
FIG. 5
FIG. 6
STEP 1 For a new loader installation, the mountings must be installed on the tractor first. Refer to the typical
mounting kit shown in Figure 1. A detailed schematic of your specific kit is available—just call 1-800-570-8205 if the
schematic was not included with your new loader.
STEP 2 The loader should have been dismounted (or assembled) on flat, level ground (see Figure 2).
STEP 3 Approach the loader as shown in Figure 3 and connect the hydraulics.
STEP 4 Once the hydraulics are functional, begin to slowly tip the bucket forward from its flat position, see Figure
4A. This will bring the upright masts of the loader towards the support shafts on the mountings (Fig. 4B). Figure 4C
shows the mast completely seated on the support shaft. Once the mast is resting on the support shaft, the V-block
will also be aligned with the tapered guide block. The lift cylinders can be used to rotate the upright mast and firmly
seat the V-block against the guide block.
STEP 5 Using a 1-1/2” socket or end wrench, install and tighten the 1” retaining bolt that secures the V-block to
the guide block. See Figure 5.
STEP 6 Raise the bucket off the ground so that the stand legs are hanging free. See Figure 6.
STEP 7 Return the stand legs to their stored position. See Figure 7.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISMOUNTING LOADER
FIG. 1
FIG. 2
Stand Legs
FIG. 3
FIG. 5
FIG. 4
FIG. 6A
FIG. 6B
FIG. 7
Upright Mast
Pillar Mount
STEP 1 DRIVE THE TRACTOR ONTO FLAT CONCRETE and place the loader in the position shown in Fig 1.
STEP 2 Remove the stand legs from their stored position and place them in their dismount position. Slide the in-
ner tubes down to the extended position and secure them with the 3/4” pins. See Fig. 2.
STEP 3 Gently lower the loader until the stand legs touch the ground. Please note that the stand legs are not de-
signed to withstand all of the down-force that can be generated with the lift cylinders, they are designed to support
the weight of the loader only. Rotate the bucket so that the cutting edge and stand legs are all resting on the
ground. See Fig. 3.
STEP 4,5 Using a 1-1/2” socket or end wrench, remove the 1” retaining bolt that secures the V-block to the guide
block. See Figures 4,5.
STEP 6 Using the bucket cylinders, slowly flatten the bucket. This will start to lift the upright mast out of the pillar
mount, see Figure 6A. When the bucket is completely flat on the ground, the upright mast will be high enough to
back away from the loader. See Figure 6B
STEP 7 Disconnect the hydraulic supply to the loader and slowly back away from the loader. See Figure 7.
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK-ATTACH INSTRUCTIONS
UNCOUPLING
1. Raise sliding latches as shown in Figure 1.
2. Rotate QT pins out of the lower notches, raise, and then rotate them into the upper notches
of the sliding latches as shown in Figure 2.
3. Slide the sliding latches down as shown in Figure 3. This secures the QT pins in the “up”
position so they do not interfere when hooking up to the next attachment.
COUPLING
1. Approach and hook onto the attachment with QT pins secured in the “up” position as shown
in Figure 3.
2. When the QT frame is flat against the attachment, raise the sliding latches as shown in Fig-
ure 2.
3. Rotate QT pins out of the upper notches, lower, and then rotate them into the lower notches
on the sliding latches as shown in Figure 1. NOTE: If the QT pins do not easily slide thru the
lug on the attachment, do not force them. Simply rotate the attachment back and forth
slowly with the bucket cylinders of the loader and the QT pins should fall into place. Periodi-
cally grease the QT pins and sliding latches.
4. Secure the QT pins in the “down” position by sliding the latches down.
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM
NO.
PART NUMBER
MF30
DESCRIPTION
MAINFRAME, GL30/GP30
QTY.
1
1
1
2
2
2
2
2
2
2
2
10
2
2
1
10
1
1
1
8
1
1
3
1
1
1
1
2
QT30
QUICK ATTACH FRAME
3
CY-059
CYLINDER, BUCKET, GL/GP30
PIN, CHROME 2" x 6" WITH RETAINER
PIN, CHROME 2" x 7" WITH RETAINER
PIN, CHROME 1-1/2 x 6-1/2 WITH RETAINER
PIN, CHROME 1-1/2 x 7-1/4 WITH RETAINER
REAR BUCKET CYLINDER PIN
LIFT CYLINDER PIN, 1-1/2 CHROME
LOCKWASHER, 1-IN., MED ZN
LOCKWASHER, 1/2, MED ZN
8
PN-600AC16
PN-700AC16
PN-650AC12
PN-725AC12
PN-11B12
34
1
9
8
10
11
12
13
14
15
16
17
18
19
26
27
28
29
30
31
32
33
34
35
36
15
PN-4750-J12
HW-LS-16-A
HW-LS-08-A
HW-NS-16-B
HW-NS-16-E
HW-NS-10-A
HW-NS-08-A
LV01-04
NUT, 1-14 UNF, GR5, NZ
19
NUT, 1-14 UNF GR8 TL, ZN
35
NUT, 5/8-11 UNC GR8, ZN
33
10
NUT, 1/2-13 UNC, ZN
SLIDE ROD ASSY, LEVEL INDICATOR
SLIDE TUBE ASSY, LEVEL INDICATOR
LEVEL INDICATOR ROD, GL/GP30
BOLT, 1/2-13 UNC, GR5 ZN, 2" LONG
BOLT, 5/8-11 UNC, GR5 ZN, 1" LONG
BOLT, 1/2-13 UNC, GR5 ZN, 1-1/2" LONG
WASHER, 1/2" FLAT, ZN
LV30-01
LV30-03
HW-BS-08-0200-A
HW-BS-10-0100-A
HW-BS-08-0150-A
HW-WS-08-A
UP30-AR
19
36
29
13
15
UPRIGHT LEG, RIGHT
UP30-AL
UPRIGHT LEG, LEFT
16
14
CY-060-L
CYLINDER, GP30 LIFT (LH)
CYLINDER, GP30 LIFT (RH)
CY-060-R
17
12
30
27
2
28
18
3
26
31
32
SC HEMATIC
9
G P30 LOADER
G ENERAL PART LIST
11
29
29
REV.
DWG . NO.
G P30
A
WEIG HT:
2061.843
DATE 1/13/2005
1
1
SHEET
OF
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM NO.
PART NUMBER
DESCRIPTION
with bearings/QTY.
20
21
22
23
2
BR-2500K-3750
PS-2000-45
BR-2000K-1500
BR-2500K-3125
COMPOSITE BEARING, 2.00 BORE, 3.75 LONG
Pin Seal (MRW), 2.0 ID x 2.5 OD x 5/16 Thick
COMPOSITE BEARING, 1.50 BORE, 1.50 LONG
COMPOSITE BEARING, 2.00 BORE, 3.125 LONG
8
2
2
21
23
21
23
21
21
22
22
21
21
SC HEMATIC
20
MAINFRAME, G L30/G P30
BEARING & SEAL DETAIL
21
21
20
REV.
DWG . NO.
MF30
A
WEIG HT:
1159.886
DATE 1/28/2005
1
1
SHEET
OF
Download from Www.Somanuals.com. All Manuals Search And Download.
4
1
2
3
3
SLIDING LATCH DETAIL
4
5
6
5
1
2
ITEM
NO.
PART
NUMBER
Pin Up Latch
Up/QTY.
DESCRIPTION
1
QT02-01L
QT02-01R
QT02-14
QT30-W
SLIDING LATCH ASSY, QT, LH
SLIDING LATCH ASSY, QT, RH
RETAINING PIN ASSEMBLY, QT
WELDED QT FRAME
1
1
2
1
5
5
6
2
3
4
6
4
4
6
4
SC HEMATIC
ITEM
NO.
PART NUMBER
DESCRIPTION
NUT, 3/8-16 UNC, CL, ZN
QTY.
QUIC K ATTAC H FRAME
G L30/G P30/G P35
4
HW-NS-06-A
HW-SP-01
4
4
4
5
6
SPRING, QT HANDLE
HW-WS-06-A
WASHER, 3/8, FLAT, ZN
REV.
DWG . NO.
QT30
A
WEIG HT:
246.509
DATE 1/13/2005
1
1
SHEET
OF
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM
NO.
with
pipes/QTY.
PART NUMBER
DESCRIPTION
HP30P-BL
HP30P-BU
HP30P-LL
BUCKET TILT FEEDLINE, LOWER
BUCKET TILT FEEDLINE, UPPER
LIFT FEEDLINE, LOWER
1
1
1
1
1
7
2
2
2
2
7
7
2
11
3
HP30P-LU
PC06X2
LIFT FEEDLINE, UPPER
4
PIPE CLAMP
5
10
HP30-HBL
HP30-HBS
HP30-HLL
HP30-HLS
HW-LS-05-A
HW-BS-05-0125-A
6
BUCKET CYLINDER HOSE, LONG (45.5")
BUCKET CYLINDER HOSE, SHORT (41")
LIFT CYLINDER HOSE, LONG (35")
LIFT CYLINDER HOSE, SHORT (24")
LOCKWASHER, 5/16, ZN
7
2
8
5
9
1
10
11
BOLT, 5/16-18 UNC, GR5 ZN, 1-1/4" LONG
4
3
8
9
8
9
7
HOSE SPECIFICATIONS
7
INSIDE DIAMETER
1/2"
W ORKING PRESSURE
90 DEGREE END
STRAIGHT END
3000 PSI
-10FJX90
-08FJX
6
6
SC HEMATIC
G L30/G P30
HOSES & PIPING
REV.
DWG . NO.
HP30
A
WEIG HT:
23.706
DATE 1/13/2005
1
1
SHEET
OF
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM
NO.
PART NUMBER
DESCRIPTION
with aux kit/QTY.
24
25
26
27
28
29
30
31
32
33
HP30P-GU
AUXILLARY FEEDLINE, UPPER
AUXILLARY FEEDLINE, LOWER
BULKHEAD CONNECTOR, -10 JIC to 1/2 NPT
PIPE CLAMP
1
1
2
9
9
9
2
1
1
2
HP30P-GL
SF-2706-LN-10-08
PC06X2
HW-BS-05-0100-A
HW-LS-05-A
HOSE
BOLT, 5/16-18 UNC, GR5 ZN, 1" LONG
LOCKWASHER, 5/16, ZN
SPECIFY LENGTH REQUIRED
HA-TP-4050-3
HA-TP-4010-3
SF-5405-06-08
TIP, FEMALE 3/8 NPT (PIONEER 4050-3)
TIP, MALE 3/8 NPT (PIONEER 4010-3)
EXPANDING PIPE ADAPTER, 3/8 to 1/2 NPT
24
30
25
30
27
29
28
SC HEMATIC
26
26
33
33
32
G L/G P30 LOADER
AUX. LINE KIT
31
REV.
DWG . NO.
AU30
A
WEIG HT:
9.0
DATE 1/13/2005
1
1
SHEET
OF
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM
NO.
1
PART NUMBER
DESCRIPTION
Stand Legs/QTY.
SL30-TL
TOP TUBE ASSY, LEFT
1
1
1
1
1
2
6
2
1
2
3
4
5
6
7
8
9
SL30-BL
SL30-HL
SL30-TR
SL30-BR
PIN1-006
PIN1-017
HW-NS-16-E
SL30-HR
BOTTOM TUBE ASSY, STAND LEG (LH)
STAND LEG HANDLE, LEFT
TOP TUBE ASSY, RIGHT
BOTTOM TUBE ASSY, STAND LEG (RH)
CLEVIS PIN, 3/4 X 3 1/2 ZNC
HAIRPIN COTTER, 2-11/16 LONG
NUT, 1-14 UNF GR8 TL, ZN
STAND LEG HANDLE, RIGHT
6
8
7
7
3
1
6
7
2
4
8
7
5
9
SC HEMATIC
G L30/G P30 LOADER
STAND LEG PART LIST
REV.
DWG . NO.
SL30H
A
WEIG HT:
85.345
DATE 1/13/2005
1
1
SHEET
OF
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
CY-059T
TUBE ASSEMBLY, GP/GL25-30 BUCKET
ROD ASSY, GL/GP30 BUCKET
1
1
1
1
1
1
4
1
1
25 1/4"
2
3
4
5
6
7
8
9
CY-059D
CP-GL-3017-S
CP-PS-3017-U
HW-NS-16-A
CP-KT-3017-U
PS-1500-45
GLAND, 3017, SHORT-TAIL
PISTON, 3017 U-CUP
NUT, 1-14 UNF, TOP LOCK, PLAIN
P-KIT, 3.000 X 1.750 UC
Pin Seal (MRW), 1.50 ID x 2.0 OD x 5/16 Thick
COMPOSITE BEARING, 1.50 BORE, 3.75 LONG
COMPOSITE BEARING, 1.50 BORE, 3.125 LONG
BR-2000K-3750
BR-2000K-3125
28 3/8"
7
1
9
7
SEE NOTE 1.
5
4
2
3
SEE NOTE 1.
7
SEE NOTE 1.
8
7
SEE NOTE 1.
ALL DIMENSIONS IN INC HES
NOTES:
1. BEARING S AND SEALS ARE SOLD SEPARATELY.
2. PAC KING KIT SHOWN IN PART LIST, BUT NOT SHOWN IN DRAWING .
SC HEMATIC
BORE
ROD
3.000
1.750
C YLINDER, G L/G P30 BUC KET
STROKE
20-5/8"
CY-059
DATE 1/28/2005
PORT STYLE
WEIG HT:
DWG . NO.
-08 JIC
49.822
LBS.
1
1
SHEET
OF
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
39 1/8" SEE NOTE 3.
1
CY-058D
ROD ASSEMBLY, GL/GP30 LIFT
NUT, 1-14 UNF, TOP LOCK, PLAIN
TUBE ASSEMBLY, GP30 LIFT, LH
GLAND, 3520 LONG-TAIL
1
1
1
1
1
1
1
2
2
3
4
5
6
7
8
HW-NS-16-A
CY-060-LT
CP-GL-3520-L
CP-PS-3520-U
CP-KT-3520-U
BR-2000K-3125
PS-1500-45
PISTON, 3520 U-CUP
P-KIT, 3.500 X 2.000 UC
COMPOSITE BEARING, 1.50 BORE, 3.125 LONG
Pin Seal (MRW), 1.50 ID x 2.0 OD x 5/16 Thick
46 7/8"
3
2
5
1
4
8
SEE NOTE 1
7
8
ALL DIMENSIONS IN INC HES
NOTES:
1. BEARING AND SEALS SOLD SEPARATELY.
2. PAC KING KIT SHOWN IN PART LIST, BUT NOT SHOWN IN DRAWING .
3. EARLY C YLINDERS (12/04-2/05) WERE 1" SHORTER AND HAD 1" LESS STROKE.
SC HEMATIC
BORE
3.500
LIFT C YLINDER, G P30, LH
ROD
2.000
STROKE
33-1/4"
CY-060-L
DATE 1/28/2005
PORT STYLE
WEIG HT:
DWG . NO.
-08 JIC
85.856
LBS.
1
1
SHEET
OF
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
CY-058D
ROD ASSEMBLY, GL/GP30 LIFT
NUT, 1-14 UNF, TOP LOCK, PLAIN
TUBE ASSEMBLY, GP30 LIFT, RH
GLAND, 3520 LONG-TAIL
1
1
1
1
1
1
1
2
39 1/8" SEE NOTE 3.
2
3
4
5
6
7
8
HW-NS-16-A
CY-060-RT
CP-GL-3520-L
CP-PS-3520-U
CP-KT-3520-U
BR-2000K-3125
PS-1500-45
PISTON, 3520 U-CUP
P-KIT, 3.500 X 2.000 UC
COMPOSITE BEARING, 1.50 BORE, 3.125 LONG
Pin Seal (MRW), 1.50 ID x 2.0 OD x 5/16 Thick
46 7/8"
3
2
5
1
4
8
7
SEE NOTE 1
8
ALL DIMENSIONS IN INC HES
NOTES:
SC HEMATIC
BORE
ROD
3.500
1. BEARING AND SEALS SOLD SEPARATELY FROM C OMPLETE C YLINDER.
2. PAC KING KIT SHOWN IN PART LIST, BUT NOT SHOWN IN DRAWING .
LIFT C YLINDER, G P30, RH
3. EARLY C YLINDERS (12/04-2/05) WERE 1" SHORTER AND HAD 1" LESS STROKE.
2.000
STROKE
33-3/4"
CY-060-R
DATE 1/28/2005
PORT STYLE
WEIG HT:
DWG . NO.
-08 JIC
85.856
LBS.
1
1
SHEET
OF
Download from Www.Somanuals.com. All Manuals Search And Download.
SEAL, U-C UP, LARG E
B/U WASHER
O-RING , LARG E
O-RING , SMALL
ROD WIPER
SEAL, U-C UP, SMALL
SNAP RING
PISTON
GLAND
FRONT OF C YLINDER
SC HEMATIC
PAC KING C ONFIG URATION, U-C UP
REV.
DWG . NO.
C P-KT-U
A
WEIG HT:
DATE 1/13/2005
1
1
SHEET
OF
Download from Www.Somanuals.com. All Manuals Search And Download.
GP30 SPECIFICATIONS
44°
2’−11"
14’−8"
13’−6"
11’−10"
34°
8"
100" TYPICAL
SPECIFICATIONS AND PERFORMANCE NUMBERS ARE FOR REFERENCE ONLY
LIFTING CAPACITY:
Breakaway Lift
Full Height Lift
: 7400 lbs.
: 6000 lbs.
With load 800mm (31.5”) ahead of bucket pivot
And 2850 psi pressure at lift cylinders
WEIGHTS:
Loader (less bucket and mounts)
8 FT Bucket
Mounting Kit (Typical)
Total
: 2090 lbs.
: 800 lbs.
: 710 lbs.
: 3600 lbs.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Dec 2004
ALL PRODUCTS MANUFACTURED BY MILLER LOADERS, INCOPRORATED (MLI) EXCEPT THE
CHROME-PLATED PIVOT PINS USED ON GREASELESS LOADERS, ARE GUARENTEED TO THE
ORIGINAL PURCHASER FOR A PERIOD OF ONE YEAR FROM THE DAY OF PURCHASE AGAINST ANY
DEFECTS IN MATERIALS AND WORKMANSHIP OF FARM LOADERS AND ATTACHMENTS THAT ARE
USED IN NORMAL FARM OPERATIONS. THE CHROME-PLATED PIVOT PINS USED ON GREASELESS
LOADERS ARE GUARENTEED TO THE ORIGINAL PURCHASER FOR A PERIOD OF FIVE YEARS FROM
THE DAY OF PURCHASE AGAINST ANY DEFECTS IN MATERIALS AND WORKMANSHIP OR AGAINST
WEAR THROUGH OF THE CHROME FINISH COVERING AT LEAST ONE-QUARTER OF THE PIN
SURFACE.
ALL GREASELESS COMPOSITE BEARINGS SOLD BUT NOT MANUFACTURED BY MLI ARE
GUARENTEED TO THE ORIGINAL PURCHASER FOR A PERIOD OF FIVE YEARS FROM THE DAY OF
PURCHASE AGAINST BREAKAGE OR LOSS OF THEIR SELF-LUBRICATING PROPERTY.
THE FIVE YEAR WARRANTY FOR THE CHROME-PLATED PIVOT PINS AND GREASELESS COMPOSITE
BEARINGS IS LIMITED TO THE PARTS ONLY. MLI IS NOT RESPONSIBLE FOR ANY LABOR NECESSARY
FOR THE INSPECTION, REMOVAL, OR REPLACEMENT OF SAID PIVOT PINS AND/OR COMPOSITE
BEARINGS.
ALL PARTS SOLD BUT NOT MANUFACTURED BY MLI THAT INCLUDE BUT ARE NOT LIMITED TO
ZINC-PLATED PINS, HOSES, VALVES, QUICK COUPLERS, PUMPS, TANKS, ETC. ARE COVERED ONLY
TO THE EXTENT OF THE MANUFACTURE’S WARRANTY ON THESE ITEMS. MLI DOES NOT
WARRANTY THESE ITEMS EXPRESSLY OR IMPLIEDLY.
DEFACEMENT OF ANY PART BY WELDING OR OTHERWISE ALTERING, OR EXCESSIVE WEAR ON PINS
CAUSED BY LACK OF LUBRICATION, NULLIFIES THE WARRANTY ON THE MLI PRODUCT.
MLI ASSUMES NO RESPONSIBILITY AS TO THE PERFORMANCE OR FAILURE OF A TRACTOR’S
HYDRAULIC SYSTEM.
THE HYDRAULIC COMPONENTS OF THE MLI PRODUCTS ARE GUARENTEED UP TO A PRESSURE OF
3000 POUNDS PER SQUARE INCH AT A MAXIMUM FLOW RATE OF 30 GALLONS PER MINUTE.
MLI ASSUMES NO RESPONSIBILITY FOR THE FAILURE OF THE PURCHASER TO SECURE THE LOADER
TO THE TRACTOR PROPER, WHICH INCLUDES PROPER BOLT TIGHTENING AND SECURING OF ALL
CONNECTION POINTS.
ALL ITEMS MANUFACTURED BY MLI REQUIRING WARRANTY CONSIDERATION MUST BE RETURNED
TO MLI OR A DESIGNATED REPRESENTATIVE BY THE ORIGINAL PURCHASER. ANY ITEM SO
RETURNED BY COMMON CARRIER MUST BE PREPAID FREIGHT.
THE WARRANTIES PROVIDED BY MLI AS REFERRED TO ABOVE SHALL BE THE SOLE AND
EXCLUSIVE WARRANTIES. THERE SHALL BE NO OTHER WARRANTIES EXPRESS OR IMPLIED
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS OR ANY OTHER
OBLIGATION ON THE PART OF MLI WITH RESPECT TO PRODUCTS COVERED BY THIS WARRANTY.
IN NO EVENT SHALL THE WARRANTIES OF MLI REQUIRE MORE FROM MLI THAN THE REPAIR OR
REPLACEMENT OF ANY PART OR PARTS WHICH ARE FOUND TO BE DEFECTIVE WITHIN THE
EFFECTIVE PERIOD OF THE WARRANTY, MLI SHALL HAVE NO LIABILITY FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
MILLER LOADERS INC, 1242 ARIZONA AVE, LARCHWOOD, IA 51241
PHONE: 1-800-570-8205
Or (712) 477-2795
FAX: (712) 477-2500
Download from Www.Somanuals.com. All Manuals Search And Download.
|